December 2022 - U-Boot

[PATCH v3 00/19] Add USB on SAM9X60, SAMA7G5 and SAMA5D2 boards
by Sergiu Moga 12 Dec '22

12 Dec '22

This series of patches is meant to add support for USB Mass Storage on SAM9X60, SAMA7G5 and SAMA5D2 boards and register ohci-at91 driver into Driver Model. In order for this to be achieved, the respective DT nodes have been added, the USB clock has been registered into CCF and the required defconfigs have been added to the boards' defconfig. What is more, in order for the VBUS to stay enabled, a `child_pre_probe` method has been added to overcome the DM core disabling it in `usb_scan_device`: when the generic `device_probe` method is called, the pinctrl is processed once again, undoing whatever changes have been made in our driver's probe method. In order to enable USB on SAMA7G5 the addition of RSTC and USB 2.0 PHY drivers were required. v1 -> v2: - Additional patch included: [PATCH v2 04/19] clk: at91: pmc: export clock setup to pmc - Updated [PATCH v2 05/19] clk: at91: sam9x60: Add initial setup of UPLL and USBCK rates in concordance with the previously mentioned additional patch - Move ` #include <asm/arch/clk.h>` below `#if !(CONFIG_IS_ENABLED(DM_USB))` to avoid implicit declarations warnings/errors in the OHCI driver v2 -> v3: - Also add USB pinctrl nodes and USB Mass Storage for SAM9X60 Curiosity and remove no longer necessary ifdef in sam9x60 clk driver - Remove no longer required CONFIG_SYS_USB_* configs from the defconfigs and add CONFIG_RESET_AT91 to all defconfigs Claudiu Beznea (1): clk: at91: pmc: export clock setup to pmc Cristian Birsan (2): ARM: at91: add sama7 SFR definitions usb: ohci-at91: Add `ohci_t` field in `ohci_at91_priv` Sergiu Moga (16): ARM: dts: sam9x60: Add OHCI and EHCI DT nodes clk: at91: Add support for sam9x60 USB clock clk: at91: sam9x60: Register the required clocks for USB clk: at91: sam9x60: Add initial setup of UPLL and USBCK rates usb: ohci-at91: Enable OHCI functionality and register into DM dt-bindings: reset: add sama7g5 definitions dt-bindings: clk: at91: Define additional UTMI related clocks ARM: dts: at91: sama7: Add USB related DT nodes reset: at91: Add reset driver for basic assert/deassert operations phy: at91: Add support for the USB 2.0 PHY's of SAMA7 usb: ohci-at91: Add USB PHY functionality ARM: dts: at91: sama5d2_icp: Add pinctrl nodes for USB related DT nodes ARM: dts: at91: sama5d27_wlsom1_ek: Add pinctrl nodes for USB DT nodes configs: at91: sam9x60ek: Add required configs for the USB command configs: at91: sama5d2: Enable OHCI/EHCI related configs configs: at91: sama7: Enable USB and RESET functionality arch/arm/dts/at91-sam9x60_curiosity.dts | 21 ++ arch/arm/dts/at91-sama5d27_wlsom1_ek.dts | 25 ++ arch/arm/dts/at91-sama5d2_icp.dts | 22 ++ arch/arm/dts/at91-sama7g5ek.dts | 34 +++ arch/arm/dts/sam9x60.dtsi | 18 ++ arch/arm/dts/sam9x60ek.dts | 21 ++ arch/arm/dts/sama7g5.dtsi | 73 ++++++ arch/arm/mach-at91/include/mach/sama7-sfr.h | 59 +++++ configs/sam9x60_curiosity_mmc_defconfig | 8 + configs/sam9x60ek_mmc_defconfig | 9 + configs/sam9x60ek_nandflash_defconfig | 9 + configs/sam9x60ek_qspiflash_defconfig | 9 + configs/sama5d27_giantboard_defconfig | 4 + configs/sama5d27_som1_ek_mmc1_defconfig | 4 + configs/sama5d27_som1_ek_mmc_defconfig | 4 + configs/sama5d27_som1_ek_qspiflash_defconfig | 4 + configs/sama5d27_wlsom1_ek_mmc_defconfig | 5 + .../sama5d27_wlsom1_ek_qspiflash_defconfig | 4 + configs/sama5d2_icp_mmc_defconfig | 8 + configs/sama5d2_icp_qspiflash_defconfig | 4 + configs/sama5d2_ptc_ek_mmc_defconfig | 4 + configs/sama5d2_ptc_ek_nandflash_defconfig | 4 + configs/sama5d2_xplained_emmc_defconfig | 4 + configs/sama5d2_xplained_mmc_defconfig | 4 + configs/sama5d2_xplained_qspiflash_defconfig | 4 + configs/sama5d2_xplained_spiflash_defconfig | 4 + configs/sama7g5ek_mmc1_defconfig | 10 + configs/sama7g5ek_mmc_defconfig | 10 + drivers/clk/at91/Kconfig | 7 + drivers/clk/at91/Makefile | 1 + drivers/clk/at91/clk-sam9x60-usb.c | 156 +++++++++++++ drivers/clk/at91/pmc.c | 42 ++++ drivers/clk/at91/pmc.h | 27 +++ drivers/clk/at91/sam9x60.c | 63 +++++ drivers/clk/at91/sama7g5.c | 48 +--- drivers/phy/Kconfig | 10 + drivers/phy/Makefile | 1 + drivers/phy/phy-sama7-usb.c | 92 ++++++++ drivers/phy/phy-sama7-utmi-clk.c | 202 ++++++++++++++++ drivers/reset/Kconfig | 8 + drivers/reset/Makefile | 1 + drivers/reset/reset-at91.c | 141 ++++++++++++ drivers/sysreset/sysreset_at91.c | 10 +- drivers/usb/host/ohci-at91.c | 215 ++++++++++++++++++ include/dt-bindings/clk/at91.h | 5 + include/dt-bindings/reset/sama7g5-reset.h | 10 + 46 files changed, 1377 insertions(+), 51 deletions(-) create mode 100644 arch/arm/mach-at91/include/mach/sama7-sfr.h create mode 100644 drivers/clk/at91/clk-sam9x60-usb.c create mode 100644 drivers/phy/phy-sama7-usb.c create mode 100644 drivers/phy/phy-sama7-utmi-clk.c create mode 100644 drivers/reset/reset-at91.c create mode 100644 include/dt-bindings/reset/sama7g5-reset.h -- 2.34.1

2 20

[PATCH v5 0/1] Makefile: rework u-boot-initial-env target
by Max Krummenacher 12 Dec '22

12 Dec '22

From: Max Krummenacher <max.krummenacher(a)toradex.com> With CONFIG_LTO enabled the current way of extracting the configured environment no longer works, i.e. the object file content changes due to LTO. Build a host tool which prints the configured environment instead of using objcopy and friends to achive the same. The code and Makefile changes were mostly stolen from tools/env/ i.e. the target userspace tools to access the environment. Changes in v5: - don't build the printinitialenv tool unconditionally but build it only as part of the u-boot-initial-env target. This no longer fails the 'make tools-only_defconfig tools-only' use-case which is reported by Tom Rini. Adding the $(env_h) dependencies to the tools target might give circular dependencies issues with some future tool. - add Acked-by: Pali Rohár <pali(a)kernel.org> Changes in v4: - add '(objtree)/' when calling the tool. Suggested by Pali Rohár. - renamed patch, as more than just the Makefile has changes Changes in v3: - moved the tool from scripts/ to tools/. Suggested by Tom Rini - changed the dependencies to '$(env_h)' and 'tools'. Suggested by Tom Rini and Pali Rohár. - removed the sed rule which replaces \x00 with \x0A as this is already done by the tool. Suggested by Pali Rohár. Changes in v2: - reworked to build a host tool which prints the configured environment as proposed by Pali Rohár https://lore.kernel.org/u-boot/20221018174827.1393211-1-max.oss.09@gmail.co… - renamed patch, v1 used "Makefile: fix u-boot-initial-env target if lto is enabled" Max Krummenacher (1): u-boot-initial-env: rework make target Makefile | 10 ++++++---- tools/.gitignore | 1 + tools/Makefile | 4 ++++ tools/printinitialenv.c | 44 +++++++++++++++++++++++++++++++++++++++++ 4 files changed, 55 insertions(+), 4 deletions(-) create mode 100644 tools/printinitialenv.c -- 2.35.3

3 5

[PATCH V2 1/1] Configs: enable gigadevice
by Victor Lim 12 Dec '22

12 Dec '22

enabling gigadevice in this file Signed-off-by: Victor Lim <vlim(a)gigadevice.com> --- configs/zynq_cse_qspi_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/configs/zynq_cse_qspi_defconfig b/configs/zynq_cse_qspi_defconfig index 60f0d7cac4..d58db07e71 100644 --- a/configs/zynq_cse_qspi_defconfig +++ b/configs/zynq_cse_qspi_defconfig @@ -71,6 +71,7 @@ CONFIG_SPI_FLASH_MACRONIX=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_SPI_FLASH_STMICRO=y CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_GIGADEVICE=y # CONFIG_SPI_FLASH_USE_4K_SECTORS is not set CONFIG_ARM_DCC=y CONFIG_ZYNQ_QSPI=y -- 2.25.1

1 0

[PATCH] phy: usbphyc: use regulator_set_enable_if_allowed for disabling vbus supply
by Patrick Delaunay 12 Dec '22

12 Dec '22

Use regulator_set_enable_if_allowed() api instead of regulator_set_enable() while disabling vbus supply. This way the driver doesn't see an error when it disable an always-on regulator for VBUS. This patch is needed for STM32MP157C-DK2 board when the regulator v3v3: buck4 used as the phy vbus supply in kernel device tree is always on with the next hack for low power use-case: &usbphyc_port0 { ... /* * Hack to keep hub active until all connected devices are suspended * otherwise the hub will be powered off as soon as the v3v3 is disabled * and it can disturb connected devices. */ connector { compatible = "usb-a-connector"; vbus-supply = <&v3v3>; }; }; Without this patch and the previous update in DT the command "usb stop" failed and the next command "usb start" cause a crash. Signed-off-by: Patrick Delaunay <patrick.delaunay(a)foss.st.com> --- drivers/phy/phy-stm32-usbphyc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/phy/phy-stm32-usbphyc.c b/drivers/phy/phy-stm32-usbphyc.c index 9f0b7d71187..dcf2194e9a7 100644 --- a/drivers/phy/phy-stm32-usbphyc.c +++ b/drivers/phy/phy-stm32-usbphyc.c @@ -375,7 +375,7 @@ static int stm32_usbphyc_phy_power_off(struct phy *phy) return 0; if (usbphyc_phy->vbus) { - ret = regulator_set_enable(usbphyc_phy->vbus, false); + ret = regulator_set_enable_if_allowed(usbphyc_phy->vbus, false); if (ret) return ret; } -- 2.25.1

4 4

[PATCH] dm: pmic: ignore disabled node in pmic_bind_children
by Patrick Delaunay 12 Dec '22

12 Dec '22

Ignore the disabled children node in pmic_bind_children() so the disabled regulators in device tree are not registered. This patch is based on the dm_scan_fdt_node() code - only the activated nodes are bound - and it solves possible issue when a deactivated regulator is bound, error for duplicated regulator name for example. Signed-off-by: Patrick Delaunay <patrick.delaunay(a)foss.st.com> --- This patch solves the errors for duplicated regulator names on STM32MP15x boards since the alignment with Linux device tree with the commit 9157a4ce36b18 ("ARM: dts: stm32: update SCMI dedicated file"). When SCMI is activated in "<board>-scmi.dts" device tree, the 3 regulators reg11, reg18, usb33 are duplicated (children of scmi_reguls and of pwr_regulators) even if the children of pwr_regulators are deactivated in the file arch/arm/dts/stm32mp15-scmi.dtsi. drivers/power/pmic/pmic-uclass.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/power/pmic/pmic-uclass.c b/drivers/power/pmic/pmic-uclass.c index 5dcf6d8079d2..0e2f5e1f4111 100644 --- a/drivers/power/pmic/pmic-uclass.c +++ b/drivers/power/pmic/pmic-uclass.c @@ -39,6 +39,10 @@ int pmic_bind_children(struct udevice *pmic, ofnode parent, node_name = ofnode_get_name(node); debug("* Found child node: '%s'\n", node_name); + if (!ofnode_is_enabled(node)) { + debug(" - ignoring disabled device\n"); + continue; + } child = NULL; for (info = child_info; info->prefix && info->driver; info++) { -- 2.25.1

4 3

[PATCH v2 00/19] Add USB on SAM9X60, SAMA7G5 and SAMA5D2 boards
by Sergiu Moga 12 Dec '22

12 Dec '22

This series of patches is meant to add support for USB Mass Storage on SAM9X60, SAMA7G5 and SAMA5D2 boards and register ohci-at91 driver into Driver Model. In order for this to be achieved, the respective DT nodes have been added, the USB clock has been registered into CCF and the required defconfigs have been added to the boards' defconfig. What is more, in order for the VBUS to stay enabled, a `child_pre_probe` method has been added to overcome the DM core disabling it in `usb_scan_device`: when the generic `device_probe` method is called, the pinctrl is processed once again, undoing whatever changes have been made in our driver's probe method. In order to enable USB on SAMA7G5 the addition of RSTC and USB 2.0 PHY drivers were required. v1 -> v2: - Additional patch included: [PATCH v2 04/19] clk: at91: pmc: export clock setup to pmc - Updated [PATCH v2 05/19] clk: at91: sam9x60: Add initial setup of UPLL and USBCK rates in concordance with the previously mentioned additional patch - Move ` #include <asm/arch/clk.h>` below `#if !(CONFIG_IS_ENABLED(DM_USB))` to avoid implicit declarations warnings/errors in the OHCI driver Claudiu Beznea (1): clk: at91: pmc: export clock setup to pmc Cristian Birsan (2): ARM: at91: add sama7 SFR definitions usb: ohci-at91: Add `ohci_t` field in `ohci_at91_priv` Sergiu Moga (16): ARM: dts: sam9x60ek: Add OHCI and EHCI DT nodes clk: at91: Add support for sam9x60 USB clock clk: at91: sam9x60: Register the required clocks for USB clk: at91: sam9x60: Add initial setup of UPLL and USBCK rates usb: ohci-at91: Enable OHCI functionality and register into DM configs: at91: sam9x60ek: Add required configs for the USB command dt-bindings: reset: add sama7g5 definitions dt-bindings: clk: at91: Define additional UTMI related clocks ARM: dts: at91: sama7: Add USB related DT nodes reset: at91: Add reset driver for basic assert/deassert operations phy: at91: Add support for the USB 2.0 PHY's of SAMA7 usb: ohci-at91: Add USB PHY functionality configs: at91: sama7: Enable USB and RESET functionality ARM: dts: at91: sama5d2_icp: Add pinctrl nodes for USB related DT nodes ARM: dts: at91: sama5d27_wlsom1_ek: Add pinctrl nodes for USB DT nodes configs: at91: sama5d2: Enable OHCI/EHCI related configs arch/arm/dts/at91-sama5d27_wlsom1_ek.dts | 25 ++ arch/arm/dts/at91-sama5d2_icp.dts | 22 ++ arch/arm/dts/at91-sama7g5ek.dts | 34 +++ arch/arm/dts/sam9x60.dtsi | 18 ++ arch/arm/dts/sam9x60ek.dts | 21 ++ arch/arm/dts/sama7g5.dtsi | 73 ++++++ arch/arm/mach-at91/include/mach/sama7-sfr.h | 59 +++++ configs/sam9x60ek_mmc_defconfig | 10 + configs/sam9x60ek_nandflash_defconfig | 10 + configs/sam9x60ek_qspiflash_defconfig | 10 + configs/sama5d27_som1_ek_mmc1_defconfig | 5 + configs/sama5d27_som1_ek_mmc_defconfig | 5 + configs/sama5d27_som1_ek_qspiflash_defconfig | 5 + configs/sama5d27_wlsom1_ek_mmc_defconfig | 6 + .../sama5d27_wlsom1_ek_qspiflash_defconfig | 5 + configs/sama5d2_icp_mmc_defconfig | 9 + configs/sama5d2_icp_qspiflash_defconfig | 9 + configs/sama5d2_ptc_ek_mmc_defconfig | 5 + configs/sama5d2_ptc_ek_nandflash_defconfig | 5 + configs/sama5d2_xplained_emmc_defconfig | 5 + configs/sama5d2_xplained_mmc_defconfig | 5 + configs/sama5d2_xplained_qspiflash_defconfig | 5 + configs/sama5d2_xplained_spiflash_defconfig | 5 + configs/sama7g5ek_mmc1_defconfig | 13 ++ configs/sama7g5ek_mmc_defconfig | 13 ++ drivers/clk/at91/Kconfig | 7 + drivers/clk/at91/Makefile | 1 + drivers/clk/at91/clk-sam9x60-usb.c | 156 +++++++++++++ drivers/clk/at91/pmc.c | 42 ++++ drivers/clk/at91/pmc.h | 27 +++ drivers/clk/at91/sam9x60.c | 67 ++++++ drivers/clk/at91/sama7g5.c | 48 +--- drivers/phy/Kconfig | 10 + drivers/phy/Makefile | 1 + drivers/phy/phy-sama7-usb.c | 92 ++++++++ drivers/phy/phy-sama7-utmi-clk.c | 202 ++++++++++++++++ drivers/reset/Kconfig | 8 + drivers/reset/Makefile | 1 + drivers/reset/reset-at91.c | 141 ++++++++++++ drivers/sysreset/sysreset_at91.c | 10 +- drivers/usb/host/ohci-at91.c | 215 ++++++++++++++++++ include/dt-bindings/clk/at91.h | 5 + include/dt-bindings/reset/sama7g5-reset.h | 10 + 43 files changed, 1374 insertions(+), 51 deletions(-) create mode 100644 arch/arm/mach-at91/include/mach/sama7-sfr.h create mode 100644 drivers/clk/at91/clk-sam9x60-usb.c create mode 100644 drivers/phy/phy-sama7-usb.c create mode 100644 drivers/phy/phy-sama7-utmi-clk.c create mode 100644 drivers/reset/reset-at91.c create mode 100644 include/dt-bindings/reset/sama7g5-reset.h -- 2.34.1

2 21

[PATCH v3 1/1] arm: mvebu: Espressobin: Fix default env variables
by Derek LaHousse 12 Dec '22

12 Dec '22

Default env variables on Espressobin boards are broken since commit c4df0f6f315c ("arm: mvebu: Espressobin: Set default value for $fdtfile env variable") as well as the 'env default -a' command. The algorithm to find free space in the default_environment[] array returns after the first env variable instead of the correct position of the last variable, where there is allocated free space. This causes that U-Boot board_late_init() function to overwrite a portion of the default environment with $ethXaddr and $fdtfile variables immediately after the first env variable and so it is overwriting other variables. This patch also adds an additional null byte to terminate the environment array. But U-Boot board_late_init() function do not fill this nul byte explicitly. And because of that, U-Boot is later trying to interpret remaining buffer as a continuation of variable list. Normally buffer should be empty but due to the above issue, it contains garbage from remaining env variables. For example 'env default -a' command results in damaging variable names. It was observed that scritaddr variable name was changed to criptaddr (without leading 's'). This bug was reported and discussed on the Armbian forum: https://forum.armbian.com/topic/19564-making-espressobin-v7-work-in-2022/?d… Fix these issues in two steps: 1) Change code which finds free space for dynamic env variables in default_environment[] array by jumping to the end of the variable list instead of jumping after the first defined variable. [By Derek] 2) Add code which appends terminating nul byte as indication of the end of the env list, after the last nul term env string. [By Pali] Fixes: c4df0f6f315c ("arm: mvebu: Espressobin: Set default value for $fdtfile env variable") Signed-off-by: Derek LaHousse <derek(a)seaofdirac.org> Signed-off-by: Pali Rohár <pali(a)kernel.org> --- Changes in v3: - End of line wrap fix Changes in v2: - Include Pali's end-of-array null - Better tags - More documentation of what is fixed diff --git a/board/Marvell/mvebu_armada-37xx/board.c b/board/Marvell/mvebu_armada-37xx/board.c index c6ecc323bb99..44c72344e8be 100644 --- a/board/Marvell/mvebu_armada-37xx/board.c +++ b/board/Marvell/mvebu_armada-37xx/board.c @@ -99,9 +99,16 @@ int board_late_init(void) if (!of_machine_is_compatible("globalscale,espressobin")) return 0; - /* Find free buffer in default_environment[] for new variables */ - while (*ptr != '\0' && *(ptr+1) != '\0') ptr++; - ptr += 2; + /* + * Find free space for new variables in default_environment[] array. + * Free space is after the last variable, each variable is termined + * by nul byte and after the last variable is additional nul byte. + * Move ptr to the position where new variable can be filled. + */ + while (*ptr != '\0') { + do { ptr++; } while (*ptr != '\0'); + ptr++; + } /* * Ensure that 'env default -a' does not erase permanent MAC addresses @@ -145,6 +152,13 @@ int board_late_init(void) strcpy(ptr, "fdtfile=marvell/armada-3720-espressobin- emmc.dtb"); else strcpy(ptr, "fdtfile=marvell/armada-3720-espressobin.dtb"); + ptr += strlen(ptr) + 1; + + /* + * After the last variable (which is nul term string) append another nul + * byte which terminates the list. So everything after ptr is ignored. + */ + *ptr = '\0'; return 0; }

2 1

[PATCH] patch V2: SPI NOR: ZynqMP: Zynq: GD25Q512: adding part # to the list
by Victor Lim 12 Dec '22

12 Dec '22

Adding GD25Q512 to the part # list. Signed-off-by: Victor Lim <vlim(a)gigadevice.com> --- drivers/mtd/spi/spi-nor-ids.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/mtd/spi/spi-nor-ids.c b/drivers/mtd/spi/spi-nor-ids.c index 92d3a4aa5d..fa8320eac2 100644 --- a/drivers/mtd/spi/spi-nor-ids.c +++ b/drivers/mtd/spi/spi-nor-ids.c @@ -120,6 +120,8 @@ const struct flash_info spi_nor_ids[] = { }, {INFO("gd25b256", 0xc84019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_HAS_LOCK | SPI_NOR_4B_OPCODES) }, + {INFO("gd25b512", 0xc8471A, 0, 64 * 1024, 1024, SECT_4K | + SPI_NOR_QUAD_READ | SPI_NOR_HAS_LOCK | SPI_NOR_4B_OPCODES)}, { INFO("gd25lq128", 0xc86018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | -- 2.25.1

2 1

[PATCH] patch V2: SPI: NOR: ZynqMp: enabling gigadevice part #
by Victor Lim 12 Dec '22

12 Dec '22

Enabling Gigadevice in the config file Signed-off-by: Victor Lim <vlim(a)gigadevice.com> --- configs/xilinx_zynqmp_mini_qspi_defconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/configs/xilinx_zynqmp_mini_qspi_defconfig b/configs/xilinx_zynqmp_mini_qspi_defconfig index 75014117f1..5e81dc193a 100644 --- a/configs/xilinx_zynqmp_mini_qspi_defconfig +++ b/configs/xilinx_zynqmp_mini_qspi_defconfig @@ -69,6 +69,7 @@ CONFIG_SPI_FLASH_MACRONIX=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_SPI_FLASH_STMICRO=y CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_GIGADEVICE=y # CONFIG_SPI_FLASH_USE_4K_SECTORS is not set # CONFIG_POWER is not set CONFIG_ARM_DCC=y @@ -78,4 +79,4 @@ CONFIG_ZYNQMP_GQSPI=y CONFIG_PANIC_HANG=y # CONFIG_GZIP is not set # CONFIG_LMB is not set -CONFIG_SPI_FLASH_GIGADEVICE=y + -- 2.25.1

2 1

[PATCH] SPI NOR: versal_virt: enabling gigadevice part #s
by Victor Lim 12 Dec '22

12 Dec '22

Enabling gigadevice part # in this config file Signed-off-by: Victor Lim <vlim(a)gigadevice.com> --- configs/xilinx_versal_virt_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/configs/xilinx_versal_virt_defconfig b/configs/xilinx_versal_virt_defconfig index 49cf7c30a8..732806559e 100644 --- a/configs/xilinx_versal_virt_defconfig +++ b/configs/xilinx_versal_virt_defconfig @@ -134,3 +134,4 @@ CONFIG_USB_GADGET_PRODUCT_NUM=0x0300 CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_USB_FUNCTION_THOR=y CONFIG_OF_LIBFDT_OVERLAY=y +CONFIG_SPI_FLASH_GIGADEVICE=y -- 2.25.1

2 1