August 2014 - U-Boot

[U-Boot] [PATCH 0/3] Serial Flash: call spi_flash_free more coherently
by Valentin Longchamp 15 Oct '14

15 Oct '14

Some board require spi_flash_free to be called after all the accesses, in order, for instance, to restore the pin multiplexing configuration in the case where the SPI pins are multiplexed. This patch series tries to enhance this. Patch 1 adds spi_flash_free calls to env_sf so that the SPI interface is always "cleaned up" after the env read/writes. Patch 2 adds a 'sf release' command that implicitly calls spi_flash_free and is thus the pendant of 'sf probe'. Patch 3 uses the 'sf command' for the km_arm board scripts. Valentin Longchamp (3): env_sf: generalize call to spi_flash_free after accesses cmd_sf: add 'release' command km_arm: call 'sf release' in the newenv and update scripts common/cmd_sf.c | 13 ++++++++++++- common/env_sf.c | 34 ++++++++++++++++------------------ include/configs/km/km_arm.h | 6 ++++-- 3 files changed, 32 insertions(+), 21 deletions(-) -- 1.8.0.1

2 6

[U-Boot] [PATCH v3] powerpc/85xx: enable some P1/P2 boards mtdparts for nor flash
by Yangbo Lu 14 Oct '14

14 Oct '14

Enable these boards mtdparts for nor flash: p1020rdb-pd, p1021rdb-pc, p1022ds, p1025twr, and p2020rdb-pc. Signed-off-by: Xie Xiaobo <X.Xie(a)freescale.com> Signed-off-by: Yangbo Lu <yangbo.lu(a)freescale.com> Cc: York Sun <yorksun(a)freescale.com> Cc: Scott Wood <scottwood(a)freescale.com> --- Changes for v2: - changed commit message - fixed max line length problem in code Changes for v3: - added a Cc to York Sun --- include/configs/P1022DS.h | 12 ++++++++++++ include/configs/p1_p2_rdb_pc.h | 31 +++++++++++++++++++++++++++++++ include/configs/p1_twr.h | 12 ++++++++++++ 3 files changed, 55 insertions(+) diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index 139d4fe..4480270 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -620,6 +620,18 @@ #endif /* + * Dynamic MTD Partition support with mtdparts + */ +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_MTDPARTS +#define CONFIG_FLASH_CFI_MTD +#define MTDIDS_DEFAULT "nor0=e8000000.nor" +#define MTDPARTS_DEFAULT "mtdparts=e8000000.nor:48m(ramdisk)," \ + "14m(diagnostic),2m(dink),6m(kernel),58112k(fs)," \ + "512k(dtb),768k(u-boot)" + +/* * Environment */ #ifdef CONFIG_SPIFLASH diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h index 07b6179..1ed8838 100644 --- a/include/configs/p1_p2_rdb_pc.h +++ b/include/configs/p1_p2_rdb_pc.h @@ -77,6 +77,16 @@ #define __SW_BOOT_NAND 0x44 #define __SW_BOOT_PCIE 0x74 #define CONFIG_SYS_L2_SIZE (256 << 10) +/* + * Dynamic MTD Partition support with mtdparts + */ +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_MTDPARTS +#define CONFIG_FLASH_CFI_MTD +#define MTDIDS_DEFAULT "nor0=ec000000.nor" +#define MTDPARTS_DEFAULT "mtdparts=ec000000.nor:128k(dtb),6016k(kernel)," \ + "57088k(fs),1m(vsc7385-firmware),1280k(u-boot)" #endif #if defined(CONFIG_P1021RDB) @@ -95,6 +105,17 @@ #define __SW_BOOT_NAND 0xec #define __SW_BOOT_PCIE 0x6c #define CONFIG_SYS_L2_SIZE (256 << 10) +/* + * Dynamic MTD Partition support with mtdparts + */ +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_MTDPARTS +#define CONFIG_FLASH_CFI_MTD +#define MTDIDS_DEFAULT "nor0=ef000000.nor" +#define MTDPARTS_DEFAULT "mtdparts=ef000000.nor:256k(vsc7385-firmware)," \ + "256k(dtb),4608k(kernel),9728k(fs)," \ + "256k(qe-ucode-firmware),1280k(u-boot)" #endif #if defined(CONFIG_P1024RDB) @@ -142,6 +163,16 @@ #define __SW_BOOT_NAND 0xe8 #define __SW_BOOT_PCIE 0xa8 #define CONFIG_SYS_L2_SIZE (512 << 10) +/* + * Dynamic MTD Partition support with mtdparts + */ +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_MTDPARTS +#define CONFIG_FLASH_CFI_MTD +#define MTDIDS_DEFAULT "nor0=ef000000.nor" +#define MTDPARTS_DEFAULT "mtdparts=ef000000.nor:256k(vsc7385-firmware)," \ + "256k(dtb),4608k(kernel),9984k(fs),1280k(u-boot)" #endif #ifdef CONFIG_SDCARD diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h index c296a07..d3093f5 100644 --- a/include/configs/p1_twr.h +++ b/include/configs/p1_twr.h @@ -389,6 +389,18 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #endif /* CONFIG_TWR-P1025 */ /* + * Dynamic MTD Partition support with mtdparts + */ +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_MTDPARTS +#define CONFIG_FLASH_CFI_MTD +#define MTDIDS_DEFAULT "nor0=ec000000.nor" +#define MTDPARTS_DEFAULT "mtdparts=ec000000.nor:256k(vsc7385-firmware)," \ + "256k(dtb),5632k(kernel),57856k(fs)," \ + "256k(qe-ucode-firmware),1280k(u-boot)" + +/* * Environment */ #ifdef CONFIG_SYS_RAMBOOT -- 1.8.5

2 2

[U-Boot] [PATCH] ARM: mx6: Add support for Kosagi Novena
by Marek Vasut 10 Oct '14

10 Oct '14

Add support for the Kosagi Novena board. Currently supported are: - I2C busses - FEC Ethernet - MMC0, MMC1, Booting from MMC - SATA - USB ports - USB Ethernet Signed-off-by: Marek Vasut <marex(a)denx.de> --- arch/arm/Kconfig | 4 + board/kosagi/novena/Kconfig | 23 ++ board/kosagi/novena/Makefile | 11 + board/kosagi/novena/novena.c | 346 +++++++++++++++++++++++++ board/kosagi/novena/novena_spl.c | 529 +++++++++++++++++++++++++++++++++++++++ board/kosagi/novena/setup.cfg | 47 ++++ configs/novena_defconfig | 4 + drivers/video/ipu_common.c | 2 +- include/configs/imx6_spl.h | 2 +- include/configs/novena.h | 306 ++++++++++++++++++++++ 10 files changed, 1272 insertions(+), 2 deletions(-) create mode 100644 board/kosagi/novena/Kconfig create mode 100644 board/kosagi/novena/Makefile create mode 100644 board/kosagi/novena/novena.c create mode 100644 board/kosagi/novena/novena_spl.c create mode 100644 board/kosagi/novena/setup.cfg create mode 100644 configs/novena_defconfig create mode 100644 include/configs/novena.h diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index f01ff8f..56f29a3 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -536,6 +536,9 @@ config TARGET_GW_VENTANA config TARGET_HUMMINGBOARD bool "Support hummingboard" +config TARGET_KOSAGI_NOVENA + bool "Support Kosagi Novena" + config TARGET_OMAP3_OVERO bool "Support omap3_overo" @@ -907,6 +910,7 @@ source "board/karo/tk71/Kconfig" source "board/karo/tx25/Kconfig" source "board/keymile/km_arm/Kconfig" source "board/kmc/kzm9g/Kconfig" +source "board/kosagi/novena/Kconfig" source "board/logicpd/am3517evm/Kconfig" source "board/logicpd/imx27lite/Kconfig" source "board/logicpd/imx31_litekit/Kconfig" diff --git a/board/kosagi/novena/Kconfig b/board/kosagi/novena/Kconfig new file mode 100644 index 0000000..4e52be9 --- /dev/null +++ b/board/kosagi/novena/Kconfig @@ -0,0 +1,23 @@ +if TARGET_KOSAGI_NOVENA + +config SYS_CPU + string + default "armv7" + +config SYS_BOARD + string + default "novena" + +config SYS_VENDOR + string + default "kosagi" + +config SYS_SOC + string + default "mx6" + +config SYS_CONFIG_NAME + string + default "novena" + +endif diff --git a/board/kosagi/novena/Makefile b/board/kosagi/novena/Makefile new file mode 100644 index 0000000..f67bbc9 --- /dev/null +++ b/board/kosagi/novena/Makefile @@ -0,0 +1,11 @@ +# +# Copyright (C) 2014 Marek Vasut <marex(a)denx.de> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +ifndef CONFIG_SPL_BUILD +obj-y := novena.o +else +obj-y := novena_spl.o +endif diff --git a/board/kosagi/novena/novena.c b/board/kosagi/novena/novena.c new file mode 100644 index 0000000..727ce1c --- /dev/null +++ b/board/kosagi/novena/novena.c @@ -0,0 +1,346 @@ +/* + * Novena board support + * + * Copyright (C) 2014 Marek Vasut <marex(a)denx.de> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/errno.h> +#include <asm/gpio.h> +#include <asm/io.h> +#include <asm/arch/clock.h> +#include <asm/arch/crm_regs.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/iomux.h> +#include <asm/arch/mxc_hdmi.h> +#include <asm/arch/sys_proto.h> +#include <asm/imx-common/boot_mode.h> +#include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/mxc_i2c.h> +#include <asm/imx-common/sata.h> +#include <asm/imx-common/video.h> +#include <fsl_esdhc.h> +#include <i2c.h> +#include <input.h> +#include <ipu_pixfmt.h> +#include <linux/fb.h> +#include <linux/input.h> +#include <malloc.h> +#include <micrel.h> +#include <miiphy.h> +#include <mmc.h> +#include <netdev.h> +#include <power/pmic.h> +#include <power/pfuze100_pmic.h> +#include <stdio_dev.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define NOVENA_BUTTON_GPIO IMX_GPIO_NR(4, 14) +#define NOVENA_SD_CD IMX_GPIO_NR(1, 4) +#define NOVENA_USB_HUB_RESET IMX_GPIO_NR(7, 12) + +/* + * GPIO button + */ +#ifdef CONFIG_KEYBOARD +static struct input_config button_input; + +static int novena_gpio_button_read_keys(struct input_config *input) +{ + int key = KEY_ENTER; + if (gpio_get_value(NOVENA_BUTTON_GPIO)) + return 0; + input_send_keycodes(&button_input, &key, 1); + return 1; +} + +static int novena_gpio_button_getc(struct stdio_dev *dev) +{ + return input_getc(&button_input); +} +static int novena_gpio_button_tstc(struct stdio_dev *dev) +{ + return input_tstc(&button_input); +} + +static int novena_gpio_button_init(struct stdio_dev *dev) +{ + gpio_direction_input(NOVENA_BUTTON_GPIO); + input_set_delays(&button_input, 250, 250); + return 0; +} + +int drv_keyboard_init(void) +{ + int error; + struct stdio_dev dev = { + .name = "button", + .flags = DEV_FLAGS_INPUT | DEV_FLAGS_SYSTEM, + .start = novena_gpio_button_init, + .getc = novena_gpio_button_getc, + .tstc = novena_gpio_button_tstc, + }; + + error = input_init(&button_input, 0); + if (error) { + debug("%s: Cannot set up input\n", __func__); + return -1; + } + button_input.read_keys = novena_gpio_button_read_keys; + + /* Register the device. init_tegra_keyboard() will be called soon */ + error = input_stdio_register(&dev); + if (error) + return error; + + return 0; +} +#endif + +/* + * SDHC + */ +#ifdef CONFIG_FSL_ESDHC +static struct fsl_esdhc_cfg usdhc_cfg[] = { + { USDHC3_BASE_ADDR, 0, 4 }, /* Micro SD */ + { USDHC2_BASE_ADDR, 0, 4 }, /* Big SD */ +}; + +int board_mmc_getcd(struct mmc *mmc) +{ + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; + + /* There is no CD for a microSD card, assume always present. */ + if (cfg->esdhc_base == USDHC3_BASE_ADDR) + return 1; + else + return !gpio_get_value(NOVENA_SD_CD); +} + +int board_mmc_init(bd_t *bis) +{ + s32 status = 0; + int index; + + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); + usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); + + for (index = 0; index < ARRAY_SIZE(usdhc_cfg); index++) + status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]); + + return status; +} +#endif + +/* + * USB + */ +#ifdef CONFIG_USB_EHCI_MX6 +int board_ehci_hcd_init(int port) +{ + /* Reset USB hub */ + if (port == 1) { + gpio_set_value(NOVENA_USB_HUB_RESET, 0); + mdelay(2); + gpio_set_value(NOVENA_USB_HUB_RESET, 1); + } + return 0; +} +#endif + +/* + * Video over HDMI + */ +#if defined(CONFIG_VIDEO_IPUV3) +static void enable_hdmi(struct display_info_t const *dev) +{ + imx_enable_hdmi_phy(); +} + +struct display_info_t const displays[] = { + { + /* HDMI Output */ + .bus = -1, + .addr = 0, + .pixfmt = IPU_PIX_FMT_RGB24, + .detect = detect_hdmi, + .enable = enable_hdmi, + .mode = { + .name = "HDMI", + .refresh = 60, + .xres = 1024, + .yres = 768, + .pixclock = 15385, + .left_margin = 220, + .right_margin = 40, + .upper_margin = 21, + .lower_margin = 7, + .hsync_len = 60, + .vsync_len = 10, + .sync = FB_SYNC_EXT, + .vmode = FB_VMODE_NONINTERLACED + } + } +}; + +size_t display_count = ARRAY_SIZE(displays); + +static void setup_display(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; + + enable_ipu_clock(); + imx_setup_hdmi(); + + /* Turn on LDB0,IPU,IPU DI0 clocks */ + setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK); + + /* set LDB0, LDB1 clk select to 011/011 */ + clrsetbits_le32(&mxc_ccm->cs2cdr, + MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK | + MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK, + (3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) | + (3 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET)); + + setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV); + + setbits_le32(&mxc_ccm->chsccdr, CHSCCDR_CLK_SEL_LDB_DI0 << + MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); + + writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES | + IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH | + IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW | + IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG | + IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT | + IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG | + IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT | + IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED | + IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0, + &iomux->gpr[2]); + + clrsetbits_le32(&iomux->gpr[3], IOMUXC_GPR3_LVDS0_MUX_CTL_MASK, + IOMUXC_GPR3_MUX_SRC_IPU1_DI0 << + IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET); +} +#endif + +int board_early_init_f(void) +{ +#if defined(CONFIG_VIDEO_IPUV3) + setup_display(); +#endif + + /* Bring Ethernet PHY out of reset. */ + gpio_set_value(IMX_GPIO_NR(3, 23), 1); + + return 0; +} + +int board_init(void) +{ + /* address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + +#ifdef CONFIG_CMD_SATA + setup_sata(); +#endif + + return 0; +} + +int checkboard(void) +{ + puts("Board: Novena 4x\n"); + return 0; +} + +int dram_init(void) +{ + gd->ram_size = imx_ddr_size(); + return 0; +} + +/* setup board specific PMIC */ +int power_init_board(void) +{ + struct pmic *p; + u32 reg; + int ret; + + power_pfuze100_init(1); + p = pmic_get("PFUZE100_PMIC"); + if (!p) + return -EINVAL; + + ret = pmic_probe(p); + if (ret) + return ret; + + pmic_reg_read(p, PFUZE100_DEVICEID, &reg); + printf("PMIC: PFUZE100 ID=0x%02x\n", reg); + + /* Set VGEN1 to 1.5V and enable */ + pmic_reg_read(p, PFUZE100_VGEN1VOL, &reg); + reg &= ~(LDO_VOL_MASK); + reg |= (LDOA_1_50V | LDO_EN); + pmic_reg_write(p, PFUZE100_VGEN1VOL, reg); + + /* Set SWBST to 5.0V and enable (for USB) */ + pmic_reg_read(p, PFUZE100_SWBSTCON1, &reg); + reg &= ~(SWBST_MODE_MASK | SWBST_VOL_MASK); + reg |= (SWBST_5_00V | SWBST_MODE_AUTO); + pmic_reg_write(p, PFUZE100_SWBSTCON1, reg); + + return 0; +} + +/* EEPROM configuration data */ +struct novena_eeprom_data { + uint8_t signature[6]; + uint8_t version; + uint8_t reserved; + uint32_t serial; + uint8_t mac[6]; + uint16_t features; +}; + +int misc_init_r(void) +{ + struct novena_eeprom_data data; + uchar *datap = (uchar *)&data; + const char *signature = "Novena"; + int ret; + + /* If 'ethaddr' is already set, do nothing. */ + if (getenv("ethaddr")) + return 0; + + /* EEPROM is at bus 2. */ + ret = i2c_set_bus_num(2); + if (ret) { + puts("Cannot select EEPROM I2C bus.\n"); + return 0; + } + + /* EEPROM is at address 0x56. */ + ret = eeprom_read(0x56, 0, datap, sizeof(data)); + if (ret) { + puts("Cannot read I2C EEPROM.\n"); + return 0; + } + + /* Check EEPROM signature. */ + if (memcmp(data.signature, signature, 6)) { + puts("Invalid I2C EEPROM signature.\n"); + return 0; + } + + /* Set ethernet address from EEPROM. */ + eth_setenv_enetaddr("ethaddr", data.mac); + + return ret; +} diff --git a/board/kosagi/novena/novena_spl.c b/board/kosagi/novena/novena_spl.c new file mode 100644 index 0000000..cce2b0e --- /dev/null +++ b/board/kosagi/novena/novena_spl.c @@ -0,0 +1,529 @@ +/* + * Novena SPL + * + * Copyright (C) 2014 Marek Vasut <marex(a)denx.de> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/clock.h> +#include <asm/arch/iomux.h> +#include <asm/arch/mx6-ddr.h> +#include <asm/arch/mx6-pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/gpio.h> +#include <asm/imx-common/boot_mode.h> +#include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/mxc_i2c.h> +#include <i2c.h> +#include <mmc.h> +#include <fsl_esdhc.h> +#include <spl.h> + +#include <asm/arch/mx6-ddr.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define UART_PAD_CTRL \ + (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CTRL \ + (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define ENET_PAD_CTRL \ + (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS) + +#define SPI_PAD_CTRL \ + (PAD_CTL_HYS | \ + PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) + +#define I2C_PAD_CTRL \ + (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_240ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE) + +#define BUTTON_PAD_CTRL \ + (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS) + +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) + +#define NOVENA_AUDIO_PWRON IMX_GPIO_NR(5, 17) +#define NOVENA_HDMI_GHOST_HPD IMX_GPIO_NR(5, 4) +#define NOVENA_PCIE_RESET_GPIO IMX_GPIO_NR(3, 29) +#define NOVENA_PCIE_POWER_ON_GPIO IMX_GPIO_NR(7, 12) +#define NOVENA_PCIE_WAKE_UP_GPIO IMX_GPIO_NR(3, 22) +#define NOVENA_PCIE_DISABLE_GPIO IMX_GPIO_NR(2, 16) + +/* + * Audio + */ +static iomux_v3_cfg_t audio_pads[] = { + /* AUD_PWRON */ + MX6_PAD_DISP0_DAT23__GPIO5_IO17 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static void novena_spl_setup_iomux_audio(void) +{ + imx_iomux_v3_setup_multiple_pads(audio_pads, ARRAY_SIZE(audio_pads)); + gpio_direction_output(NOVENA_AUDIO_PWRON, 1); +} + +/* + * ENET + */ +static iomux_v3_cfg_t enet_pads1[] = { + MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), + /* pin 35 - 1 (PHY_AD2) on reset */ + MX6_PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* pin 32 - 1 - (MODE0) all */ + MX6_PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* pin 31 - 1 - (MODE1) all */ + MX6_PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* pin 28 - 1 - (MODE2) all */ + MX6_PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* pin 27 - 1 - (MODE3) all */ + MX6_PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */ + MX6_PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* pin 42 PHY nRST */ + MX6_PAD_EIM_D23__GPIO3_IO23 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static iomux_v3_cfg_t enet_pads2[] = { + MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), +}; + +static void novena_spl_setup_iomux_enet(void) +{ + imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1)); + imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2)); + + gpio_direction_output(IMX_GPIO_NR(3, 23), 0); + gpio_direction_output(IMX_GPIO_NR(6, 30), 1); + gpio_direction_output(IMX_GPIO_NR(6, 25), 1); + gpio_direction_output(IMX_GPIO_NR(6, 27), 1); + gpio_direction_output(IMX_GPIO_NR(6, 28), 1); + gpio_direction_output(IMX_GPIO_NR(6, 29), 1); + gpio_direction_output(IMX_GPIO_NR(6, 24), 1); +} + +/* + * GPIO Button + */ +static iomux_v3_cfg_t button_pads[] = { + /* Debug */ + MX6_PAD_KEY_COL4__GPIO4_IO14 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), +}; + +static void novena_spl_setup_iomux_buttons(void) +{ + imx_iomux_v3_setup_multiple_pads(button_pads, ARRAY_SIZE(button_pads)); +} + +/* + * I2C + */ +/* I2C1, RAM */ +struct i2c_pads_info i2c_pad_info0 = { + .scl = { + .i2c_mode = MX6_PAD_EIM_D21__I2C1_SCL | PC, + .gpio_mode = MX6_PAD_EIM_D21__GPIO3_IO21 | PC, + .gp = IMX_GPIO_NR(3, 21) + }, + .sda = { + .i2c_mode = MX6_PAD_EIM_D28__I2C1_SDA | PC, + .gpio_mode = MX6_PAD_EIM_D28__GPIO3_IO28 | PC, + .gp = IMX_GPIO_NR(3, 28) + } +}; + +/* I2C2 Camera, MIPI */ +static struct i2c_pads_info i2c_pad_info1 = { + .scl = { + .i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | PC, + .gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | PC, + .gp = IMX_GPIO_NR(2, 30) + }, + .sda = { + .i2c_mode = MX6_PAD_EIM_D16__I2C2_SDA | PC, + .gpio_mode = MX6_PAD_EIM_D16__GPIO3_IO16 | PC, + .gp = IMX_GPIO_NR(3, 16) + } +}; + +/* I2C3, J15 - RGB connector */ +static struct i2c_pads_info i2c_pad_info2 = { + .scl = { + .i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC, + .gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | PC, + .gp = IMX_GPIO_NR(3, 17) + }, + .sda = { + .i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC, + .gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC, + .gp = IMX_GPIO_NR(3, 18) + } +}; + +static void novena_spl_setup_iomux_i2c(void) +{ + setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0); + setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); + setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); +} + +/* + * PCI express + */ +#ifdef CONFIG_CMD_PCI +static iomux_v3_cfg_t pcie_pads[] = { + /* "Reset" pin */ + MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* "Power on" pin */ + MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* "Wake up" pin (input) */ + MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* "Disable endpoint" (rfkill) pin */ + MX6_PAD_EIM_A22__GPIO2_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static void novena_spl_setup_iomux_pcie(void) +{ + imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads)); + + /* Ensure PCIe is powered down */ + gpio_direction_output(NOVENA_PCIE_POWER_ON_GPIO, 0); + + /* Put the card into reset */ + gpio_direction_output(NOVENA_PCIE_RESET_GPIO, 0); + + /* Input signal to wake system from mPCIe card */ + gpio_direction_input(NOVENA_PCIE_WAKE_UP_GPIO); + + /* Drive RFKILL high, to ensure the radio is turned on */ + gpio_direction_output(NOVENA_PCIE_DISABLE_GPIO, 1); +} +#else +static inline void novena_spl_setup_iomux_pcie(void) {} +#endif + +/* + * SDHC + */ +static iomux_v3_cfg_t usdhc2_pads[] = { + MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ +}; + +static iomux_v3_cfg_t usdhc3_pads[] = { + MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), +}; + +static void novena_spl_setup_iomux_sdhc(void) +{ + imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); + imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); + + /* Micro SD card detect */ + gpio_direction_input(IMX_GPIO_NR(7, 0)); + + /* Big SD card detect */ + gpio_direction_input(IMX_GPIO_NR(1, 4)); +} + +/* + * SPI + */ +#ifdef CONFIG_MXC_SPI +static iomux_v3_cfg_t ecspi1_pads[] = { + /* SS1 */ + MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), +}; + +static void novena_spl_setup_iomux_spi(void) +{ + imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); + gpio_direction_output(CONFIG_SF_DEFAULT_CS, 1); +} +#else +static void novena_spl_setup_iomux_spi(void) {} +#endif + +/* + * UART + */ +static iomux_v3_cfg_t const uart1_pads[] = { + MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static iomux_v3_cfg_t const uart2_pads[] = { + MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static void novena_spl_setup_iomux_uart(void) +{ + imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); + imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads)); +} + +/* + * USB + */ +#ifdef CONFIG_USB_EHCI_MX6 +static iomux_v3_cfg_t usb_pads[] = { + MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static void novena_spl_setup_iomux_usb(void) +{ + imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads)); +} +#else +static void novena_spl_setup_iomux_usb(void) {} +#endif + +/* + * Video + */ +#ifdef CONFIG_VIDEO +static iomux_v3_cfg_t hdmi_pads[] = { + /* "Ghost HPD" pin */ + MX6_PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static void novena_spl_setup_iomux_video(void) +{ + imx_iomux_v3_setup_multiple_pads(hdmi_pads, ARRAY_SIZE(hdmi_pads)); + gpio_direction_input(NOVENA_HDMI_GHOST_HPD); +} +#else +static inline void novena_spl_setup_iomux_video(void) {} +#endif + +/* + * SPL boots from uSDHC card + */ +#ifdef CONFIG_FSL_ESDHC +static struct fsl_esdhc_cfg usdhc_cfg = { + USDHC3_BASE_ADDR, 0, 4 +}; + +int board_mmc_getcd(struct mmc *mmc) +{ + /* There is no CD for a microSD card, assume always present. */ + return 1; +} + +int board_mmc_init(bd_t *bis) +{ + usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); + return fsl_esdhc_initialize(bis, &usdhc_cfg); +} +#endif + +/* Configure MX6Q/DUAL mmdc DDR io registers */ +static struct mx6dq_iomux_ddr_regs novena_ddr_ioregs = { + /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */ + .dram_sdclk_0 = 0x00020038, + .dram_sdclk_1 = 0x00020038, + .dram_cas = 0x00000038, + .dram_ras = 0x00000038, + .dram_reset = 0x00000038, + /* SDCKE[0:1]: 100k pull-up */ + .dram_sdcke0 = 0x00003000, + .dram_sdcke1 = 0x00003000, + /* SDBA2: pull-up disabled */ + .dram_sdba2 = 0x00000000, + /* SDODT[0:1]: 100k pull-up, 40 ohm */ + .dram_sdodt0 = 0x00000038, + .dram_sdodt1 = 0x00000038, + /* SDQS[0:7]: Differential input, 40 ohm */ + .dram_sdqs0 = 0x00000038, + .dram_sdqs1 = 0x00000038, + .dram_sdqs2 = 0x00000038, + .dram_sdqs3 = 0x00000038, + .dram_sdqs4 = 0x00000038, + .dram_sdqs5 = 0x00000038, + .dram_sdqs6 = 0x00000038, + .dram_sdqs7 = 0x00000038, + + /* DQM[0:7]: Differential input, 40 ohm */ + .dram_dqm0 = 0x00000038, + .dram_dqm1 = 0x00000038, + .dram_dqm2 = 0x00000038, + .dram_dqm3 = 0x00000038, + .dram_dqm4 = 0x00000038, + .dram_dqm5 = 0x00000038, + .dram_dqm6 = 0x00000038, + .dram_dqm7 = 0x00000038, +}; + +/* Configure MX6Q/DUAL mmdc GRP io registers */ +static struct mx6dq_iomux_grp_regs novena_grp_ioregs = { + /* DDR3 */ + .grp_ddr_type = 0x000c0000, + .grp_ddrmode_ctl = 0x00020000, + /* Disable DDR pullups */ + .grp_ddrpke = 0x00000000, + /* ADDR[00:16], SDBA[0:1]: 40 ohm */ + .grp_addds = 0x00000038, + /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */ + .grp_ctlds = 0x00000038, + /* DATA[00:63]: Differential input, 40 ohm */ + .grp_ddrmode = 0x00020000, + .grp_b0ds = 0x00000038, + .grp_b1ds = 0x00000038, + .grp_b2ds = 0x00000038, + .grp_b3ds = 0x00000038, + .grp_b4ds = 0x00000038, + .grp_b5ds = 0x00000038, + .grp_b6ds = 0x00000038, + .grp_b7ds = 0x00000038, +}; + +static struct mx6_mmdc_calibration novena_mmdc_calib = { + /* write leveling calibration determine */ + .p0_mpwldectrl0 = 0x00420048, + .p0_mpwldectrl1 = 0x006f0059, + .p1_mpwldectrl0 = 0x005a0104, + .p1_mpwldectrl1 = 0x01070113, + /* Read DQS Gating calibration */ + .p0_mpdgctrl0 = 0x437c040b, + .p0_mpdgctrl1 = 0x0413040e, + .p1_mpdgctrl0 = 0x444f0446, + .p1_mpdgctrl1 = 0x044d0422, + /* Read Calibration: DQS delay relative to DQ read access */ + .p0_mprddlctl = 0x4c424249, + .p1_mprddlctl = 0x4e48414f, + /* Write Calibration: DQ/DM delay relative to DQS write access */ + .p0_mpwrdlctl = 0x42414641, + .p1_mpwrdlctl = 0x46374b43, +}; + +static struct mx6_ddr_sysinfo novena_ddr_info = { + /* Width of data bus: 0=16, 1=32, 2=64 */ + .dsize = 2, + /* Config for full 4GB range so that get_mem_size() works */ + .cs_density = 32, /* 32Gb per CS */ + /* Single chip select */ + .ncs = 1, + .cs1_mirror = 0, + .rtt_wr = 1, /* RTT_Wr = RZQ/4 */ + .rtt_nom = 2, /* RTT_Nom = RZQ/2 */ + .walat = 3, /* Write additional latency */ + .ralat = 7, /* Read additional latency */ + .mif3_mode = 3, /* Command prediction working mode */ + .bi_on = 1, /* Bank interleaving enabled */ + .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ + .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ +}; + +static struct mx6_ddr3_cfg elpida_4gib_1600 = { + .mem_speed = 1600, + .density = 4, + .width = 64, + .banks = 8, + .rowaddr = 16, + .coladdr = 10, + .pagesz = 2, + .trcd = 1300, + .trcmin = 4900, + .trasmin = 3590, +}; + +/* + * called from C runtime startup code (arch/arm/lib/crt0.S:_main) + * - we have a stack and a place to store GD, both in SRAM + * - no variable global data is available + */ +void board_init_f(ulong dummy) +{ + /* + * Zero out global data: + * - this should be done by crt0.S + * - failure to zero it will cause i2c_setup to fail + */ + memset((void *)gd, 0, sizeof(struct global_data)); + + /* setup AIPS and disable watchdog */ + arch_cpu_init(); + + /* setup GP timer */ + timer_init(); + +#ifdef CONFIG_BOARD_POSTCLK_INIT + board_postclk_init(); +#endif +#ifdef CONFIG_FSL_ESDHC + get_clocks(); +#endif + + /* Setup IOMUX and configure basics. */ + novena_spl_setup_iomux_audio(); + novena_spl_setup_iomux_buttons(); + novena_spl_setup_iomux_enet(); + novena_spl_setup_iomux_i2c(); + novena_spl_setup_iomux_pcie(); + novena_spl_setup_iomux_sdhc(); + novena_spl_setup_iomux_spi(); + novena_spl_setup_iomux_uart(); + novena_spl_setup_iomux_usb(); + novena_spl_setup_iomux_video(); + + /* UART clocks enabled and gd valid - init serial console */ + preloader_console_init(); + + /* Start the DDR DRAM */ + mx6dq_dram_iocfg(64, &novena_ddr_ioregs, &novena_grp_ioregs); + mx6_dram_cfg(&novena_ddr_info, &novena_mmdc_calib, &elpida_4gib_1600); + + /* Clear the BSS. */ + memset(__bss_start, 0, __bss_end - __bss_start); + + /* load/boot image from boot device */ + board_init_r(NULL, 0); +} + +void reset_cpu(ulong addr) +{ +} diff --git a/board/kosagi/novena/setup.cfg b/board/kosagi/novena/setup.cfg new file mode 100644 index 0000000..18d139c --- /dev/null +++ b/board/kosagi/novena/setup.cfg @@ -0,0 +1,47 @@ +/* + * Copyright (C) 2014 Marek Vasut <marex(a)denx.de> + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ + +/* image version */ +IMAGE_VERSION 2 + +/* Boot Device : sd */ +BOOT_FROM sd + +#define __ASSEMBLY__ +#include <config.h> +#include "asm/arch/iomux.h" +#include "asm/arch/crm_regs.h" + +/* set the default clock gate to save power */ +DATA 4, CCM_CCGR0, 0x00C03F3F +DATA 4, CCM_CCGR1, 0x0030FC03 +DATA 4, CCM_CCGR2, 0x0FFFC000 +DATA 4, CCM_CCGR3, 0x3FF00000 +DATA 4, CCM_CCGR4, 0xFFFFF300 /* enable NAND/GPMI/BCH clocks */ +DATA 4, CCM_CCGR5, 0x0F0000C3 +DATA 4, CCM_CCGR6, 0x000003FF + +/* enable AXI cache for VDOA/VPU/IPU */ +DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF +/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ +DATA 4, MX6_IOMUXC_GPR6, 0x007F007F +DATA 4, MX6_IOMUXC_GPR7, 0x007F007F + +/* + * Setup CCM_CCOSR register as follows: + * + * cko1_en = 1 --> CKO1 enabled + * cko1_div = 111 --> divide by 8 + * cko1_sel = 1011 --> ahb_clk_root + * + * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz + */ +DATA 4, CCM_CCOSR, 0x000000fb diff --git a/configs/novena_defconfig b/configs/novena_defconfig new file mode 100644 index 0000000..a560afb --- /dev/null +++ b/configs/novena_defconfig @@ -0,0 +1,4 @@ +CONFIG_SPL=y +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/kosagi/novena/setup.cfg,MX6Q,SPL" ++S:CONFIG_ARM=y ++S:CONFIG_TARGET_KOSAGI_NOVENA=y diff --git a/drivers/video/ipu_common.c b/drivers/video/ipu_common.c index 8d4e925..e238492 100644 --- a/drivers/video/ipu_common.c +++ b/drivers/video/ipu_common.c @@ -203,7 +203,7 @@ static struct clk ipu_clk = { #else .enable_reg = (u32 *)(CCM_BASE_ADDR + offsetof(struct mxc_ccm_reg, CCGR3)), - .enable_shift = MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET, + .enable_shift = MXC_CCM_CCGR3_IPU1_IPU_MASK, #endif .enable = clk_ipu_enable, .disable = clk_ipu_disable, diff --git a/include/configs/imx6_spl.h b/include/configs/imx6_spl.h index 970460d..52fe9cf 100644 --- a/include/configs/imx6_spl.h +++ b/include/configs/imx6_spl.h @@ -27,7 +27,7 @@ #define CONFIG_SYS_THUMB_BUILD #define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/omap-common/u-boot-spl.lds" #define CONFIG_SPL_TEXT_BASE 0x00908000 -#define CONFIG_SPL_MAX_SIZE (64 * 1024) +#define CONFIG_SPL_MAX_SIZE 0x10000 #define CONFIG_SPL_START_S_PATH "arch/arm/cpu/armv7" #define CONFIG_SPL_STACK 0x0091FFB8 #define CONFIG_SPL_LIBCOMMON_SUPPORT diff --git a/include/configs/novena.h b/include/configs/novena.h new file mode 100644 index 0000000..b986767 --- /dev/null +++ b/include/configs/novena.h @@ -0,0 +1,306 @@ +/* + * Configuration settings for the Novena U-boot. + * + * Copyright (C) 2014 Marek Vasut <marex(a)denx.de> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* System configurations */ +#define CONFIG_MX6 +#define CONFIG_SYS_MX6_HCLK 24000000 +#define CONFIG_SYS_MX6_CLK32 32768 +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_MISC_INIT_R +#define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DOS_PARTITION +#define CONFIG_FAT_WRITE +#define CONFIG_FIT +#define CONFIG_KEYBOARD +#define CONFIG_MXC_GPIO +#define CONFIG_OF_LIBFDT +#define CONFIG_REGEX +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_SYS_NO_FLASH + +#include "configs/mx6_common.h" +#include <asm/arch/imx-regs.h> +#include <asm/imx-common/gpio.h> +#include <config_cmd_default.h> + +/* U-Boot Commands */ +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_BMODE +#define CONFIG_CMD_BOOTZ +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_EXT4 +#define CONFIG_CMD_EXT4_WRITE +#define CONFIG_CMD_FAT +#define CONFIG_CMD_FS_GENERIC +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IMXOTP +#define CONFIG_CMD_MII +#define CONFIG_CMD_MMC +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_SATA +#define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_TIME +#define CONFIG_CMD_USB +#define CONFIG_VIDEO + +/* U-Boot general configurations */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) + /* Print buffer size */ +#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + /* Boot argument buffer size */ +#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ +#define CONFIG_AUTO_COMPLETE /* Command auto complete */ +#define CONFIG_CMDLINE_EDITING /* Command history etc */ +#define CONFIG_SYS_HUSH_PARSER + +/* U-Boot environment */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_ENV_SIZE (16 * 1024) +/* + * Environment is on MMC, starting at offset 64KiB from start of the card. + * Please place first partition at offset 1MiB from the start of the card + * as recommended by GNU/fdisk. See below for details: + * http://homepage.ntlworld.com./jonathan.deboynepollard/FGA/disc-partition-al… + */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_OFFSET (512 * 1024) +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE +#define CONFIG_ENV_OFFSET_REDUND \ + (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#else +#define CONFIG_ENV_IS_NOWHERE +#endif + +/* Booting Linux */ +#define CONFIG_BOOTDELAY 5 +#define CONFIG_BOOTFILE "fitImage" +#define CONFIG_BOOTARGS "console=ttymxc1,115200 " +#define CONFIG_BOOTCOMMAND "run net_nfs" +#define CONFIG_LOADADDR 0x18000000 +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR +#define CONFIG_HOSTNAME novena + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR +#define PHYS_SDRAM_SIZE 0xF0000000 + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +#define CONFIG_SYS_MEMTEST_START 0x10000000 +#define CONFIG_SYS_MEMTEST_END 0x20000000 + +#define CONFIG_SYS_MALLOC_LEN (64 * 1024 * 1024) + +/* SPL */ +#define CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SPL_MMC_SUPPORT +#include "imx6_spl.h" /* common IMX6 SPL configuration */ + +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_REVISION_TAG + +/* Ethernet Configuration */ +#ifdef CONFIG_CMD_NET +#define CONFIG_FEC_MXC +#define CONFIG_MII +#define IMX_FEC_BASE ENET_BASE_ADDR +#define CONFIG_FEC_XCV_TYPE RGMII +#define CONFIG_ETHPRIME "FEC" +#define CONFIG_FEC_MXC_PHYADDR 0x7 +#define CONFIG_PHYLIB +#define CONFIG_PHY_MICREL +#define CONFIG_PHY_MICREL_KSZ9021 +#define CONFIG_ARP_TIMEOUT 200UL +#endif + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_MXC +#define CONFIG_SYS_I2C_SPEED 100000 + +/* I2C EEPROM */ +#ifdef CONFIG_CMD_EEPROM +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_SPD_BUS_NUM 2 +#endif + +/* MMC Configs */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_BOUNCE_BUFFER +#define CONFIG_FSL_ESDHC +#define CONFIG_FSL_USDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR 0 +#define CONFIG_SYS_FSL_USDHC_NUM 2 +#endif + +/* OCOTP Configs */ +#ifdef CONFIG_CMD_IMXOTP +#define CONFIG_IMX_OTP +#define IMX_OTP_BASE OCOTP_BASE_ADDR +#define IMX_OTP_ADDR_MAX 0x7F +#define IMX_OTP_DATA_ERROR_VAL 0xBADABADA +#endif + +/* PCI express */ +#undef CONFIG_CMD_PCI /* Disable to prevent Linux from hanging on MX6 */ +#ifdef CONFIG_CMD_PCI +#define CONFIG_PCI +#define CONFIG_PCI_PNP +#define CONFIG_PCI_SCAN_SHOW +#define CONFIG_PCIE_IMX +#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(3, 29) +#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(7, 12) +#endif + +/* PMIC */ +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_PFUZE100 +#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 + +/* SATA Configs */ +#ifdef CONFIG_CMD_SATA +#define CONFIG_DWC_AHSATA +#define CONFIG_SYS_SATA_MAX_DEVICE 1 +#define CONFIG_DWC_AHSATA_PORT_ID 0 +#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR +#define CONFIG_LBA48 +#define CONFIG_LIBATA +#endif + +/* UART */ +#define CONFIG_MXC_UART +#define CONFIG_MXC_UART_BASE UART2_BASE +#define CONFIG_BAUDRATE 115200 +#define CONFIG_CONS_INDEX 1 + +/* USB Configs */ +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_MX6 +#define CONFIG_USB_STORAGE +#define CONFIG_USB_KEYBOARD +#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP +#define CONFIG_USB_HOST_ETHER +#define CONFIG_USB_ETHER_ASIX +#define CONFIG_USB_ETHER_SMSC95XX +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) +#define CONFIG_MXC_USB_FLAGS 0 +/* Gadget part */ +#define CONFIG_CI_UDC +#define CONFIG_USBD_HS +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_USB_ETHER +#define CONFIG_USB_ETH_CDC +#define CONFIG_NETCONSOLE +#endif + +/* Video output */ +#ifdef CONFIG_VIDEO +#define CONFIG_VIDEO +#define CONFIG_VIDEO_IPUV3 +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_VIDEO_BMP_RLE8 +#define CONFIG_SPLASH_SCREEN +#define CONFIG_BMP_16BPP +#define CONFIG_VIDEO_LOGO +#define CONFIG_IPUV3_CLK 260000000 +#define CONFIG_CMD_HDMIDETECT +#define CONFIG_CONSOLE_MUX +#define CONFIG_IMX_HDMI +#define CONFIG_IMX_VIDEO_SKIP +#endif + +/* Extra U-Boot environment. */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "fdt_high=0xffffffff\0" \ + "initrd_high=0xffffffff\0" \ + "consdev=ttymxc1\0" \ + "baudrate=115200\0" \ + "bootdev=/dev/mmcblk0p1\0" \ + "rootdev=/dev/mmcblk0p2\0" \ + "netdev=eth0\0" \ + "rootpath=/opt/eldk-5.5/armv7a-hf/rootfs-qte-sdk\0" \ + "kernel_addr_r=0x18000000\0" \ + "addcons=" \ + "setenv bootargs ${bootargs} " \ + "console=${consdev},${baudrate}\0" \ + "addip=" \ + "setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:" \ + "${netmask}:${hostname}:${netdev}:off\0" \ + "addmisc=" \ + "setenv bootargs ${bootargs} ${miscargs}\0" \ + "addargs=run addcons addmisc\0" \ + "mmcload=" \ + "mmc rescan ; " \ + "ext4load mmc 0:1 ${kernel_addr_r} ${bootfile}\0" \ + "netload=" \ + "tftp ${kernel_addr_r} ${hostname}/${bootfile}\0" \ + "miscargs=nohlt panic=1\0" \ + "mmcargs=setenv bootargs root=${rootdev} rw rootwait\0" \ + "nfsargs=" \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath},v3,tcp\0" \ + "mmc_mmc=" \ + "run mmcload mmcargs addargs ; " \ + "bootm ${kernel_addr_r}\0" \ + "mmc_nfs=" \ + "run mmcload nfsargs addip addargs ; " \ + "bootm ${kernel_addr_r}\0" \ + "net_mmc=" \ + "run netload mmcargs addargs ; " \ + "bootm ${kernel_addr_r}\0" \ + "net_nfs=" \ + "run netload nfsargs addip addargs ; " \ + "bootm ${kernel_addr_r}\0" \ + "update_sd_spl_filename=SPL\0" \ + "update_sd_uboot_filename=u-boot.img\0" \ + "update_sd_firmware=" /* Update the SD firmware partition */ \ + "if mmc rescan ; then " \ + "if dhcp ${update_sd_spl_filename} ; then " \ + "mmc write ${loadaddr} 2 0x200 ; " \ + "fi ; " \ + "if dhcp ${update_sd_uboot_filename} ; then " \ + "fatwrite mmc 0:1 ${loadaddr} u-boot.img ${filesize} ; "\ + "fi ; " \ + "fi\0" \ + +#endif /* __CONFIG_H */ -- 2.0.0

6 19

[U-Boot] Pull request for u-boot-marvell.git
by Prafulla Wadaskar 08 Oct '14

08 Oct '14

Hi Albert, Please pull The following changes since commit 4b0561d84198f8d696fd51cfc27aeac8c7482a8c: Albert ARIBAUD (1): Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' are available in the git repository at: u-boot-marvell.git master branch. Holger Brunck (1): arm/km: fix i2c mux define for km_kirkwood_128m16 target Karlheinz Jerg (1): arm/km: add support for km_kirkwood_128m16 board Luka Perkov (1): kirkwood: ib62x0: use device tree and update config boards.cfg | 1 + include/configs/ib62x0.h | 38 +++++++++++++++++++++++--------------- include/configs/km_kirkwood.h | 10 ++++++++++ 3 files changed, 34 insertions(+), 15 deletions(-) Regards... Prafulla . . .

2 3

[U-Boot] [PATCH 0/2] e1000: add i210 support
by Tim Harvey 04 Oct '14

04 Oct '14

Two patches to add Intel i210 support to the e1000 driver. Marek Vasut (2): e1000: Implement dcache support e1000: add i210 support drivers/net/e1000.c | 266 ++++++++++++++++++++++++++++++++++++++++++---------- drivers/net/e1000.h | 12 +++ include/pci_ids.h | 7 ++ 3 files changed, 236 insertions(+), 49 deletions(-) -- 1.8.3.2

5 13

[U-Boot] Call for participation in the U-Boot Mini Summit 2014
by Detlev Zundel 02 Oct '14

02 Oct '14

Hi, as already indicated, we are looking forward to our next U-Boot Mini Summit at Embedded Linux Conference Europe 2014 which will take place in Düsseldorf, Germany from October 13 - 15. The call for papers of the main conference is now open[1] and if you want to submit a talk for the main tracks, you should note the deadline of July 11. For our U-Boot Mini Summit, I'd like to get the schedule completed synchronized to the schedule release of the main event, which is August 12. So please submit talk proposals here with at least me on CC. To coordinate the event better, I have setup another wiki page[2] that can and _should_ be edited by the interested parties. Feel free for example to add yourself to the "interested participants" so that we get an idea of how many of the U-Boot developers will be there. Best wishes Detlev [1] http://events.linuxfoundation.org/events/embedded-linux-conference-europe/p… [2] http://www.denx.de/wiki/U-Boot/MiniSummitELCE2014 -- Blaming Snowden for causing problems for the US cloud industry is like blaming Al Gore for the global warming. -- Mikko Hypponen -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-40 Fax: (+49)-8142-66989-80 Email: dzu(a)denx.de

13 27

[U-Boot] [PATCH v2] mvebu_mmc: Driver addition
by Mario Schuknecht 02 Oct '14

02 Oct '14

In function mvebu_mmc_write notice command timeout. It is possible that a command is done, but a timeout occurred. Enable timeout in set bus function. Set window registers. Without that I could not use the driver on a Kirkwood 88F6282 SoC. Set high capacity and 52MHz driver feature. Signed-off-by: Mario Schuknecht <mario.schuknecht(a)dresearch-fe.de> --- Changes in v2: - Correct indentation - Remove unneeded parentheses - Use correct coding style for multi-line statements drivers/mmc/mvebu_mmc.c | 62 ++++++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 61 insertions(+), 1 deletion(-) diff --git a/drivers/mmc/mvebu_mmc.c b/drivers/mmc/mvebu_mmc.c index 9759198..d34e743 100644 --- a/drivers/mmc/mvebu_mmc.c +++ b/drivers/mmc/mvebu_mmc.c @@ -17,8 +17,12 @@ #include <asm/arch/kirkwood.h> #include <mvebu_mmc.h> +DECLARE_GLOBAL_DATA_PTR; + #define DRIVER_NAME "MVEBU_MMC" +#define MVEBU_TARGET_DRAM 0 + static void mvebu_mmc_write(u32 offs, u32 val) { writel(val, CONFIG_SYS_MMC_BASE + (offs)); @@ -164,6 +168,9 @@ static int mvebu_mmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, return TIMEOUT; } } + if (mvebu_mmc_read(SDIO_ERR_INTR_STATUS) & + (SDIO_ERR_CMD_TIMEOUT | SDIO_ERR_DATA_TIMEOUT)) + return TIMEOUT; /* Handling response */ if (cmd->resp_type & MMC_RSP_136) { @@ -271,6 +278,7 @@ static void mvebu_mmc_set_bus(unsigned int bus) /* default to maximum timeout */ ctrl_reg |= SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX); + ctrl_reg |= SDIO_HOST_CTRL_TMOUT_EN; ctrl_reg |= SDIO_HOST_CTRL_PUSH_PULL_EN; @@ -296,6 +304,55 @@ static void mvebu_mmc_set_ios(struct mmc *mmc) mvebu_mmc_set_clk(mmc->clock); } +/* + * Set window register. + */ +static void mvebu_window_setup(void) +{ + int i; + + for (i = 0; i < 4; i++) { + mvebu_mmc_write(WINDOW_CTRL(i), 0); + mvebu_mmc_write(WINDOW_BASE(i), 0); + } + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + u32 size, base, attrib; + + /* Enable DRAM bank */ + switch (i) { + case 0: + attrib = KWCPU_ATTR_DRAM_CS0; + break; + case 1: + attrib = KWCPU_ATTR_DRAM_CS1; + break; + case 2: + attrib = KWCPU_ATTR_DRAM_CS2; + break; + case 3: + attrib = KWCPU_ATTR_DRAM_CS3; + break; + default: + /* invalide bank, disable access */ + attrib = 0; + break; + } + + size = gd->bd->bi_dram[i].size; + base = gd->bd->bi_dram[i].start; + if (size && attrib) { + mvebu_mmc_write(WINDOW_CTRL(i), + MVCPU_WIN_CTRL_DATA(size, + MVEBU_TARGET_DRAM, + attrib, + MVCPU_WIN_ENABLE)); + } else { + mvebu_mmc_write(WINDOW_CTRL(i), MVCPU_WIN_DISABLE); + } + mvebu_mmc_write(WINDOW_BASE(i), base); + } +} + static int mvebu_mmc_initialize(struct mmc *mmc) { debug("%s: mvebu_mmc_initialize", DRIVER_NAME); @@ -322,6 +379,8 @@ static int mvebu_mmc_initialize(struct mmc *mmc) mvebu_mmc_write(SDIO_NOR_INTR_EN, 0); mvebu_mmc_write(SDIO_ERR_INTR_EN, 0); + mvebu_window_setup(); + /* SW reset */ mvebu_mmc_write(SDIO_SW_RESET, SDIO_SW_RESET_NOW); @@ -342,7 +401,8 @@ static struct mmc_config mvebu_mmc_cfg = { .f_min = MVEBU_MMC_BASE_FAST_CLOCK / MVEBU_MMC_BASE_DIV_MAX, .f_max = MVEBU_MMC_CLOCKRATE_MAX, .voltages = MMC_VDD_32_33 | MMC_VDD_33_34, - .host_caps = MMC_MODE_4BIT | MMC_MODE_HS, + .host_caps = MMC_MODE_4BIT | MMC_MODE_HS | MMC_MODE_HC | + MMC_MODE_HS_52MHz, .part_type = PART_TYPE_DOS, .b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT, }; -- 1.8.4.5

3 3

[U-Boot] [PATCH] mmc: fix ERASE_GRP_DEF handling
by Hannes Petermaier 02 Oct '14

02 Oct '14

if we set manually this bit on the eMMC card using mmc_switch(...), we also have to set it within our (before read) internal structure 'ext_csd'. Otherwise following checks on this will fail. Signed-off-by: Hannes Petermaier <oe5hpm(a)oevsv.at> --- drivers/mmc/mmc.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c index a26f3ce..52a8e36 100644 --- a/drivers/mmc/mmc.c +++ b/drivers/mmc/mmc.c @@ -1010,6 +1010,8 @@ static int mmc_startup(struct mmc *mmc) if (err) return err; + else + ext_csd[EXT_CSD_ERASE_GROUP_DEF] = 1; /* Read out group size from ext_csd */ mmc->erase_grp_size = -- 1.7.10.4

3 3

[U-Boot] [PATCH] mmc: set correct block size value in bfin sdh driver
by Sonic Zhang 02 Oct '14

02 Oct '14

From: Sonic Zhang <sonic.zhang(a)analog.com> Wait data transfer till the data end bit other than the data block end bit is set. Signed-off-by: Sonic Zhang <sonic.zhang(a)analog.com> --- drivers/mmc/bfin_sdh.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/mmc/bfin_sdh.c b/drivers/mmc/bfin_sdh.c index bcd6a3e..9bdfbbc 100644 --- a/drivers/mmc/bfin_sdh.c +++ b/drivers/mmc/bfin_sdh.c @@ -138,9 +138,9 @@ static int sdh_setup_data(struct mmc *mmc, struct mmc_data *data) if (data->flags & MMC_DATA_WRITE) return UNUSABLE_ERR; #ifndef RSI_BLKSZ - data_ctl |= ((ffs(data_size) - 1) << 4); + data_ctl |= ((ffs(data->blocksize) - 1) << 4); #else - bfin_write_SDH_BLK_SIZE(data_size); + bfin_write_SDH_BLK_SIZE(data->blocksize); #endif data_ctl |= DTX_DIR; bfin_write_SDH_DATA_CTL(data_ctl); @@ -189,7 +189,8 @@ static int bfin_sdh_request(struct mmc *mmc, struct mmc_cmd *cmd, do { udelay(1); status = bfin_read_SDH_STATUS(); - } while (!(status & (DAT_BLK_END | DAT_END | DAT_TIME_OUT | DAT_CRC_FAIL | RX_OVERRUN))); + } while (!(status & (DAT_END | DAT_TIME_OUT | DAT_CRC_FAIL | + RX_OVERRUN))); if (status & DAT_TIME_OUT) { bfin_write_SDH_STATUS_CLR(DAT_TIMEOUT_STAT); -- 1.8.2.3

2 2

[U-Boot] [GENERIC_BOARD] env problems before relocation with ppc8360
by Valentin Longchamp 01 Oct '14

01 Oct '14

Hello, I am currently porting all the Keymile boards to CONFIG_SYS_GENERIC_BOARD. On u-boot 2014.10-rc1 I have all of them working quite well (at least booting and showing no obvious problem), except for our boards using a MPC8360 from Freescale (kmcoge5ne and kmeter1, both using km8360.h as config) that do not boot at all. I have found out that u-boot crashes as soon as a getenv function call happens before relocation. When I disable them, u-boot seems to work fine. I am currently trying to debug further, but it's not clear yet exactly what causes the crash. We also have quite a few MPC8321 boards (for instance tuxx1.h or suvd3.h) and there the problem is not present, while the environment is also in the NOR flash as on km8360 and their core also a e300 (so their initialization is VERY similar). Has anybody seen a similar problem so far ? Has anybody a clue why this could be a HW related problem (I don't think so) ? or what is the difference in both configs (km8360 and tuxx1 for intance) that causes this behaviour ? Best Regards Valentin Signed-off-by: Valentin Longchamp <valentin.longchamp(a)keymile.com> --- common/board_f.c | 7 ++++--- include/configs/km8360.h | 2 ++ 2 files changed, 6 insertions(+), 3 deletions(-) diff --git a/common/board_f.c b/common/board_f.c index 6203d85..9f034ab 100644 --- a/common/board_f.c +++ b/common/board_f.c @@ -133,7 +133,8 @@ void board_add_ram_info(int) static int init_baud_rate(void) { - gd->baudrate = getenv_ulong("baudrate", 10, CONFIG_BAUDRATE); + //gd->baudrate = getenv_ulong("baudrate", 10, CONFIG_BAUDRATE); + gd->baudrate = CONFIG_BAUDRATE; return 0; } @@ -798,7 +799,7 @@ static init_fnc_t init_sequence_f[] = { setup_ram_buf, #endif setup_mon_len, - setup_fdt, + //setup_fdt, trace_early_init, #if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) /* TODO: can this go into arch_cpu_init()? */ @@ -933,7 +934,7 @@ static init_fnc_t init_sequence_f[] = { reserve_logbuffer, #endif #ifdef CONFIG_PRAM - reserve_pram, + //reserve_pram, #endif reserve_round_4k, #if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF)) && \ diff --git a/include/configs/km8360.h b/include/configs/km8360.h index f5ac32a..c21c194 100644 --- a/include/configs/km8360.h +++ b/include/configs/km8360.h @@ -51,6 +51,8 @@ #define CONFIG_QE /* Has QE */ #define CONFIG_MPC8360 /* MPC8360 CPU specific */ +#define CONFIG_SYS_GENERIC_BOARD + #define CONFIG_SYS_TEXT_BASE 0xF0000000 /* include common defines/options for all 83xx Keymile boards */ -- 1.8.0.1

3 5