January 2019 - U-Boot

[U-Boot] [PATCH 0/9] Support 4GB of memory on 32bit systems
by Philipp Tomsich 19 Jan '19

19 Jan '19

Even on 32bit systems a full 4GB of DRAM may be installed and reported by the DRAM controller. Whether these 4GB are larger available depends on the size/configuration of address decoding windows and architectural features. This increases the fields holding the RAM size to have at least 33bits (i.e. we use a u64) and fixes the fallout from the change: some casts, the usage of min() and a few printf formats have to be adjusted. Philipp Tomsich (9): dm: allow 4GB of DRAM on 32bit systems rockchip: support 4GB DRAM on 32bit systems common: include <inttypes.h> always MIPS: use PRIx64 macros for printing ram size rockchip: rk3368: change type of ram-size field for a min()-calculation ram: stm32mp1: use PRIx64 macros for printing ram size board: keymile: add explicit cast to truncate the 64bit ram size field board: cm_fx6: use PRIx64 macros for printing ram size mpc85xx: add casts for ram size in min() calculation. arch/arm/include/asm/arch-rockchip/sdram_common.h | 2 +- arch/arm/mach-rockchip/sdram_common.c | 8 ++++---- arch/arm/mach-stm32mp/dram_init.c | 2 +- arch/mips/mach-bmips/dram.c | 2 +- arch/powerpc/cpu/mpc85xx/cpu.c | 6 ++++-- board/compulab/cm_fx6/cm_fx6.c | 3 ++- board/keymile/km_arm/km_arm.c | 6 ++++-- drivers/ram/rockchip/dmc-rk3368.c | 2 +- drivers/ram/stm32mp1/stm32mp1_ram.c | 2 +- include/asm-generic/global_data.h | 2 +- include/common.h | 1 + include/ram.h | 9 ++++++++- 12 files changed, 29 insertions(+), 16 deletions(-) -- 2.1.4

14 39

[U-Boot] [PATCH 1/2] ARM: dts: sun8i: Update A80 dts(i) from Linux-v4.18-rc3
by Jagan Teki 19 Jan '19

19 Jan '19

Update all A80 devicetree dtsi and dtsi files from Linux-v4.18-rc3 with below commits. arch/arm/boot/dts/sun9i-a80*: commit 190e3138f9577885691540dca59c2f07540bde04 Merge: cafc87023b0d a7affb13b271 Author: Arnd Bergmann <arnd(a)arndb.de> Date: Tue Mar 27 14:58:00 2018 +0200 Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt include/dt-bindings/*/sun9i-a80-*: commit 783ab76ae553abc23f80ef7511052d055697531b Author: Chen-Yu Tsai <wens(a)csie.org> Date: Sat Jan 28 20:22:36 2017 +0800 clk: sunxi-ng: Add A80 Display Engine CCU Note: sun9i-a80-cx-a99.dts is updated only uart0, since the same dts is not available in Linux. Signed-off-by: Jagan Teki <jagan(a)amarulasolutions.com> --- arch/arm/dts/sun9i-a80-cubieboard4.dts | 260 ++++- arch/arm/dts/sun9i-a80-cx-a99.dts | 2 +- arch/arm/dts/sun9i-a80-optimus.dts | 227 ++++- arch/arm/dts/sun9i-a80.dtsi | 1062 +++++++++++++-------- include/dt-bindings/clock/sun9i-a80-ccu.h | 162 ++++ include/dt-bindings/clock/sun9i-a80-de.h | 80 ++ include/dt-bindings/clock/sun9i-a80-usb.h | 59 ++ include/dt-bindings/reset/sun9i-a80-ccu.h | 102 ++ include/dt-bindings/reset/sun9i-a80-de.h | 58 ++ include/dt-bindings/reset/sun9i-a80-usb.h | 56 ++ 10 files changed, 1597 insertions(+), 471 deletions(-) create mode 100644 include/dt-bindings/clock/sun9i-a80-ccu.h create mode 100644 include/dt-bindings/clock/sun9i-a80-de.h create mode 100644 include/dt-bindings/clock/sun9i-a80-usb.h create mode 100644 include/dt-bindings/reset/sun9i-a80-ccu.h create mode 100644 include/dt-bindings/reset/sun9i-a80-de.h create mode 100644 include/dt-bindings/reset/sun9i-a80-usb.h diff --git a/arch/arm/dts/sun9i-a80-cubieboard4.dts b/arch/arm/dts/sun9i-a80-cubieboard4.dts index 1526b41c70..85da85faf8 100644 --- a/arch/arm/dts/sun9i-a80-cubieboard4.dts +++ b/arch/arm/dts/sun9i-a80-cubieboard4.dts @@ -47,7 +47,6 @@ #include "sun9i-a80.dtsi" #include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/pinctrl/sun4i-a10.h> / { model = "Cubietech Cubieboard4"; @@ -63,8 +62,6 @@ leds { compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins_cubieboard4>; green { label = "cubieboard4:green:usr"; @@ -76,18 +73,96 @@ gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ }; }; + + vga-connector { + compatible = "vga-connector"; + label = "vga"; + ddc-i2c-bus = <&i2c3>; + + port { + vga_con_in: endpoint { + remote-endpoint = <&vga_dac_out>; + }; + }; + }; + + vga-dac { + compatible = "corpro,gm7123", "adi,adv7123", "dumb-vga-dac"; + vdd-supply = <&reg_dcdc1>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + vga_dac_in: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_out_vga>; + }; + }; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + vga_dac_out: endpoint@0 { + reg = <0>; + remote-endpoint = <&vga_con_in>; + }; + }; + }; + }; + + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + /* enables internal regulator and de-asserts reset */ + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ + }; +}; + +&de { + status = "okay"; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; + status = "okay"; }; &mmc0 { pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>; + pinctrl-0 = <&mmc0_pins>; vmmc-supply = <&reg_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */ - cd-inverted; + cd-gpios = <&pio 7 18 GPIO_ACTIVE_LOW>; /* PH18 */ + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&reg_dldo1>; + vqmmc-supply = <&reg_cldo3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; status = "okay"; }; +&mmc1_pins { + bias-pull-up; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_pins>; @@ -100,23 +175,12 @@ &mmc2_8bit_pins { /* Increase drive strength for DDR modes */ - allwinner,drive = <SUN4I_PINCTRL_40_MA>; + drive-strength = <40>; }; -&pio { - led_pins_cubieboard4: led-pins@0 { - allwinner,pins = "PH6", "PH17"; - allwinner,function = "gpio_out"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; - }; - - mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 { - allwinner,pins = "PH18"; - allwinner,function = "gpio_in"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; - }; +&osc32k { + /* osc32k input is from AC100 */ + clocks = <&ac100_rtc 0>; }; &r_ir { @@ -248,14 +312,166 @@ reg_rtc_ldo: rtc_ldo { regulator-name = "vcc-rtc-vdd1v8-io"; }; + + sw { + /* unused */ + }; + }; + }; + + axp806: pmic@745 { + compatible = "x-powers,axp806"; + reg = <0x745>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + bldoin-supply = <&reg_dcdce>; + + regulators { + reg_s_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; + }; + + aldo2 { + /* + * unused, but use a different name to + * avoid name clash with axp809's aldo's + */ + regulator-name = "s_aldo2"; + }; + + aldo3 { + /* + * unused, but use a different name to + * avoid name clash with axp809's aldo's + */ + regulator-name = "s_aldo3"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + regulator-name = "vcc18-efuse-adc-display-csi"; + }; + + reg_bldo2: bldo2 { + regulator-always-on; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + regulator-name = + "vdd18-drampll-vcc18-pll-cpvdd"; + }; + + bldo3 { + /* unused */ + }; + + reg_bldo4: bldo4 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vcc12-hsic"; + }; + + reg_cldo1: cldo1 { + /* + * This was 3V in the original design, but + * 3.3V is the recommended supply voltage + * for the Ethernet PHY. + */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-gmac-phy"; + }; + + reg_cldo2: cldo2 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "afvcc-cam"; + }; + + reg_cldo3: cldo3 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-io-wifi-codec-io2"; + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-vpu"; + }; + + reg_dcdce: dcdce { + regulator-always-on; + regulator-min-microvolt = <2100000>; + regulator-max-microvolt = <2100000>; + regulator-name = "vcc-bldo-codec-ldoin"; + }; + + sw { + /* + * unused, but use a different name to + * avoid name clash with axp809's sw + */ + regulator-name = "s_sw"; + }; + }; + }; + + ac100: codec@e89 { + compatible = "x-powers,ac100"; + reg = <0xe89>; + + ac100_codec: codec { + compatible = "x-powers,ac100-codec"; + interrupt-parent = <&r_pio>; + interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */ + #clock-cells = <0>; + clock-output-names = "4M_adda"; + }; + + ac100_rtc: rtc { + compatible = "x-powers,ac100-rtc"; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + clocks = <&ac100_codec>; + #clock-cells = <1>; + clock-output-names = "cko1_rtc", + "cko2_rtc", + "cko3_rtc"; }; }; }; #include "axp809.dtsi" +&tcon0 { + pinctrl-names = "default"; + pinctrl-0 = <&lcd0_rgb888_pins>; +}; + +&tcon0_out { + tcon0_out_vga: endpoint@0 { + reg = <0>; + remote-endpoint = <&vga_dac_in>; + }; +}; + &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; + pinctrl-0 = <&uart0_ph_pins>; status = "okay"; }; diff --git a/arch/arm/dts/sun9i-a80-cx-a99.dts b/arch/arm/dts/sun9i-a80-cx-a99.dts index a30b6fec56..cf126bbd2c 100644 --- a/arch/arm/dts/sun9i-a80-cx-a99.dts +++ b/arch/arm/dts/sun9i-a80-cx-a99.dts @@ -365,7 +365,7 @@ */ &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; + pinctrl-0 = <&uart0_ph_pins>; status = "okay"; }; diff --git a/arch/arm/dts/sun9i-a80-optimus.dts b/arch/arm/dts/sun9i-a80-optimus.dts index 7fd22e8886..58a199b0e4 100644 --- a/arch/arm/dts/sun9i-a80-optimus.dts +++ b/arch/arm/dts/sun9i-a80-optimus.dts @@ -46,7 +46,6 @@ #include "sun9i-a80.dtsi" #include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/pinctrl/sun4i-a10.h> / { model = "Merrii A80 Optimus Board"; @@ -63,11 +62,8 @@ leds { compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins_optimus>, <&led_r_pins_optimus>; /* The LED names match those found on the board */ - led2 { label = "optimus:led2:usr"; gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; @@ -87,8 +83,6 @@ reg_usb1_vbus: usb1-vbus { compatible = "regulator-fixed"; pinctrl-names = "default"; - pinctrl-0 = <&usb1_vbus_pin_optimus>; - regulator-name = "usb1-vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; enable-active-high; @@ -98,13 +92,19 @@ reg_usb3_vbus: usb3-vbus { compatible = "regulator-fixed"; pinctrl-names = "default"; - pinctrl-0 = <&usb3_vbus_pin_optimus>; - regulator-name = "usb3-vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; enable-active-high; gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ }; + + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + /* enables internal regulator and de-asserts reset */ + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ + }; }; &ehci0 { @@ -112,7 +112,8 @@ }; &ehci1 { - status = "okay"; + /* Enable if HSIC peripheral is connected */ + status = "disabled"; }; &ehci2 { @@ -121,14 +122,28 @@ &mmc0 { pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>; + pinctrl-0 = <&mmc0_pins>; vmmc-supply = <&reg_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */ - cd-inverted; + cd-gpios = <&pio 7 18 GPIO_ACTIVE_LOW>; /* PH8 */ + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&reg_dldo1>; + vqmmc-supply = <&reg_cldo3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; status = "okay"; }; +&mmc1_pins { + bias-pull-up; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_pins>; @@ -141,7 +156,7 @@ &mmc2_8bit_pins { /* Increase drive strength for DDR modes */ - allwinner,drive = <SUN4I_PINCTRL_40_MA>; + drive-strength = <40>; }; &ohci0 { @@ -152,49 +167,15 @@ status = "okay"; }; -&pio { - led_pins_optimus: led-pins@0 { - allwinner,pins = "PH0", "PH1"; - allwinner,function = "gpio_out"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; - }; - - mmc0_cd_pin_optimus: mmc0_cd_pin@0 { - allwinner,pins = "PH18"; - allwinner,function = "gpio_in"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; - }; - - usb1_vbus_pin_optimus: usb1_vbus_pin@1 { - allwinner,pins = "PH4"; - allwinner,function = "gpio_out"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; - }; - - usb3_vbus_pin_optimus: usb3_vbus_pin@1 { - allwinner,pins = "PH5"; - allwinner,function = "gpio_out"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; - }; +&osc32k { + /* osc32k input is from AC100 */ + clocks = <&ac100_rtc 0>; }; &r_ir { status = "okay"; }; -&r_pio { - led_r_pins_optimus: led-pins@1 { - allwinner,pins = "PM15"; - allwinner,function = "gpio_out"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; - }; -}; - &r_rsb { status = "okay"; @@ -320,6 +301,146 @@ reg_rtc_ldo: rtc_ldo { regulator-name = "vcc-rtc-vdd1v8-io"; }; + + sw { + /* unused */ + }; + }; + }; + + axp806: pmic@745 { + compatible = "x-powers,axp806"; + reg = <0x745>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + bldoin-supply = <&reg_dcdce>; + + regulators { + reg_s_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; + }; + + aldo2 { + /* + * unused, but use a different name to + * avoid name clash with axp809's aldo's + */ + regulator-name = "s_aldo2"; + }; + + aldo3 { + /* + * unused, but use a different name to + * avoid name clash with axp809's aldo's + */ + regulator-name = "s_aldo3"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + regulator-name = "vcc18-efuse-adc-display-csi"; + }; + + reg_bldo2: bldo2 { + regulator-always-on; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + regulator-name = + "vdd18-drampll-vcc18-pll-cpvdd"; + }; + + bldo3 { + /* unused */ + }; + + reg_bldo4: bldo4 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vcc12-hsic"; + }; + + reg_cldo1: cldo1 { + /* + * This was 3V in the original design, but + * 3.3V is the recommended supply voltage + * for the Ethernet PHY. + */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-gmac-phy"; + }; + + reg_cldo2: cldo2 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "afvcc-cam"; + }; + + reg_cldo3: cldo3 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-io-wifi-codec-io2"; + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-vpu"; + }; + + reg_dcdce: dcdce { + regulator-always-on; + regulator-min-microvolt = <2100000>; + regulator-max-microvolt = <2100000>; + regulator-name = "vcc-bldo-codec-ldoin"; + }; + + sw { + /* + * unused, but use a different name to + * avoid name clash with axp809's sw + */ + regulator-name = "s_sw"; + }; + }; + }; + + ac100: codec@e89 { + compatible = "x-powers,ac100"; + reg = <0xe89>; + + ac100_codec: codec { + compatible = "x-powers,ac100-codec"; + interrupt-parent = <&r_pio>; + interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */ + #clock-cells = <0>; + clock-output-names = "4M_adda"; + }; + + ac100_rtc: rtc { + compatible = "x-powers,ac100-rtc"; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + clocks = <&ac100_codec>; + #clock-cells = <1>; + clock-output-names = "cko1_rtc", + "cko2_rtc", + "cko3_rtc"; }; }; }; @@ -328,7 +449,7 @@ &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; + pinctrl-0 = <&uart0_ph_pins>; status = "okay"; }; @@ -338,7 +459,9 @@ }; &usbphy2 { - status = "okay"; + phy-supply = <&reg_bldo4>; + /* Enable if HSIC peripheral is connected */ + status = "disabled"; }; &usbphy3 { diff --git a/arch/arm/dts/sun9i-a80.dtsi b/arch/arm/dts/sun9i-a80.dtsi index 92412b2ac1..25591d6883 100644 --- a/arch/arm/dts/sun9i-a80.dtsi +++ b/arch/arm/dts/sun9i-a80.dtsi @@ -42,13 +42,18 @@ * OTHER DEALINGS IN THE SOFTWARE. */ -#include "skeleton64.dtsi" - #include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/pinctrl/sun4i-a10.h> +#include <dt-bindings/clock/sun9i-a80-ccu.h> +#include <dt-bindings/clock/sun9i-a80-de.h> +#include <dt-bindings/clock/sun9i-a80-usb.h> +#include <dt-bindings/reset/sun9i-a80-ccu.h> +#include <dt-bindings/reset/sun9i-a80-de.h> +#include <dt-bindings/reset/sun9i-a80-usb.h> / { + #address-cells = <2>; + #size-cells = <2>; interrupt-parent = <&gic>; cpus { @@ -58,57 +63,76 @@ cpu0: cpu@0 { compatible = "arm,cortex-a7"; device_type = "cpu"; + cci-control-port = <&cci_control0>; + clock-frequency = <12000000>; + enable-method = "allwinner,sun9i-a80-smp"; reg = <0x0>; }; cpu1: cpu@1 { compatible = "arm,cortex-a7"; device_type = "cpu"; + cci-control-port = <&cci_control0>; + clock-frequency = <12000000>; + enable-method = "allwinner,sun9i-a80-smp"; reg = <0x1>; }; cpu2: cpu@2 { compatible = "arm,cortex-a7"; device_type = "cpu"; + cci-control-port = <&cci_control0>; + clock-frequency = <12000000>; + enable-method = "allwinner,sun9i-a80-smp"; reg = <0x2>; }; cpu3: cpu@3 { compatible = "arm,cortex-a7"; device_type = "cpu"; + cci-control-port = <&cci_control0>; + clock-frequency = <12000000>; + enable-method = "allwinner,sun9i-a80-smp"; reg = <0x3>; }; cpu4: cpu@100 { compatible = "arm,cortex-a15"; device_type = "cpu"; + cci-control-port = <&cci_control1>; + clock-frequency = <18000000>; + enable-method = "allwinner,sun9i-a80-smp"; reg = <0x100>; }; cpu5: cpu@101 { compatible = "arm,cortex-a15"; device_type = "cpu"; + cci-control-port = <&cci_control1>; + clock-frequency = <18000000>; + enable-method = "allwinner,sun9i-a80-smp"; reg = <0x101>; }; cpu6: cpu@102 { compatible = "arm,cortex-a15"; device_type = "cpu"; + cci-control-port = <&cci_control1>; + clock-frequency = <18000000>; + enable-method = "allwinner,sun9i-a80-smp"; reg = <0x102>; }; cpu7: cpu@103 { compatible = "arm,cortex-a15"; device_type = "cpu"; + cci-control-port = <&cci_control1>; + clock-frequency = <18000000>; + enable-method = "allwinner,sun9i-a80-smp"; reg = <0x103>; }; }; - memory { - /* 8GB max. with LPAE */ - reg = <0 0x20000000 0x02 0>; - }; - timer { compatible = "arm,armv7-timer"; interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, @@ -139,7 +163,7 @@ * would also throw all the PLL clock rates off, or just the * downstream clocks in the PRCM. */ - osc24M: osc24M_clk { + osc24M: clk-24M { #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <24000000>; @@ -148,244 +172,28 @@ /* * The 32k clock is from an external source, normally the - * AC100 codec/RTC chip. This clock is by default enabled - * and clocked at 32768 Hz, from the oscillator connected - * to the AC100. It is configurable, but no such driver or - * bindings exist yet. + * AC100 codec/RTC chip. This serves as a placeholder for + * board dts files to specify the source. */ - osc32k: osc32k_clk { + osc32k: clk-32k { #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <32768>; + compatible = "fixed-factor-clock"; + clock-div = <1>; + clock-mult = <1>; clock-output-names = "osc32k"; }; - usb_mod_clk: clk@00a08000 { - #clock-cells = <1>; - #reset-cells = <1>; - compatible = "allwinner,sun9i-a80-usb-mod-clk"; - reg = <0x00a08000 0x4>; - clocks = <&ahb1_gates 1>; - clock-output-names = "usb0_ahb", "usb_ohci0", - "usb1_ahb", "usb_ohci1", - "usb2_ahb", "usb_ohci2"; - }; - - usb_phy_clk: clk@00a08004 { - #clock-cells = <1>; - #reset-cells = <1>; - compatible = "allwinner,sun9i-a80-usb-phy-clk"; - reg = <0x00a08004 0x4>; - clocks = <&ahb1_gates 1>; - clock-output-names = "usb_phy0", "usb_hsic1_480M", - "usb_phy1", "usb_hsic2_480M", - "usb_phy2", "usb_hsic_12M"; - }; - - pll3: clk@06000008 { - /* placeholder until implemented */ - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-rate = <0>; - clock-output-names = "pll3"; - }; - - pll4: clk@0600000c { - #clock-cells = <0>; - compatible = "allwinner,sun9i-a80-pll4-clk"; - reg = <0x0600000c 0x4>; - clocks = <&osc24M>; - clock-output-names = "pll4"; - }; - - pll12: clk@0600002c { - #clock-cells = <0>; - compatible = "allwinner,sun9i-a80-pll4-clk"; - reg = <0x0600002c 0x4>; - clocks = <&osc24M>; - clock-output-names = "pll12"; - }; - - gt_clk: clk@0600005c { - #clock-cells = <0>; - compatible = "allwinner,sun9i-a80-gt-clk"; - reg = <0x0600005c 0x4>; - clocks = <&osc24M>, <&pll4>, <&pll12>, <&pll12>; - clock-output-names = "gt"; - }; - - ahb0: clk@06000060 { - #clock-cells = <0>; - compatible = "allwinner,sun9i-a80-ahb-clk"; - reg = <0x06000060 0x4>; - clocks = <&gt_clk>, <&pll4>, <&pll12>, <&pll12>; - clock-output-names = "ahb0"; - }; - - ahb1: clk@06000064 { - #clock-cells = <0>; - compatible = "allwinner,sun9i-a80-ahb-clk"; - reg = <0x06000064 0x4>; - clocks = <&gt_clk>, <&pll4>, <&pll12>, <&pll12>; - clock-output-names = "ahb1"; - }; - - ahb2: clk@06000068 { - #clock-cells = <0>; - compatible = "allwinner,sun9i-a80-ahb-clk"; - reg = <0x06000068 0x4>; - clocks = <&gt_clk>, <&pll4>, <&pll12>, <&pll12>; - clock-output-names = "ahb2"; - }; - - apb0: clk@06000070 { - #clock-cells = <0>; - compatible = "allwinner,sun9i-a80-apb0-clk"; - reg = <0x06000070 0x4>; - clocks = <&osc24M>, <&pll4>; - clock-output-names = "apb0"; - }; - - apb1: clk@06000074 { - #clock-cells = <0>; - compatible = "allwinner,sun9i-a80-apb1-clk"; - reg = <0x06000074 0x4>; - clocks = <&osc24M>, <&pll4>; - clock-output-names = "apb1"; - }; - - cci400_clk: clk@06000078 { - #clock-cells = <0>; - compatible = "allwinner,sun9i-a80-gt-clk"; - reg = <0x06000078 0x4>; - clocks = <&osc24M>, <&pll4>, <&pll12>, <&pll12>; - clock-output-names = "cci400"; - }; - - mmc0_clk: clk@06000410 { - #clock-cells = <1>; - compatible = "allwinner,sun9i-a80-mmc-clk"; - reg = <0x06000410 0x4>; - clocks = <&osc24M>, <&pll4>; - clock-output-names = "mmc0", "mmc0_output", - "mmc0_sample"; - }; - - mmc1_clk: clk@06000414 { - #clock-cells = <1>; - compatible = "allwinner,sun9i-a80-mmc-clk"; - reg = <0x06000414 0x4>; - clocks = <&osc24M>, <&pll4>; - clock-output-names = "mmc1", "mmc1_output", - "mmc1_sample"; - }; - - mmc2_clk: clk@06000418 { - #clock-cells = <1>; - compatible = "allwinner,sun9i-a80-mmc-clk"; - reg = <0x06000418 0x4>; - clocks = <&osc24M>, <&pll4>; - clock-output-names = "mmc2", "mmc2_output", - "mmc2_sample"; - }; - - mmc3_clk: clk@0600041c { - #clock-cells = <1>; - compatible = "allwinner,sun9i-a80-mmc-clk"; - reg = <0x0600041c 0x4>; - clocks = <&osc24M>, <&pll4>; - clock-output-names = "mmc3", "mmc3_output", - "mmc3_sample"; - }; - - ahb0_gates: clk@06000580 { - #clock-cells = <1>; - compatible = "allwinner,sun9i-a80-ahb0-gates-clk"; - reg = <0x06000580 0x4>; - clocks = <&ahb0>; - clock-indices = <0>, <1>, <3>, - <5>, <8>, <12>, - <13>, <14>, - <15>, <16>, <18>, - <20>, <21>, <22>, - <23>; - clock-output-names = "ahb0_fd", "ahb0_ve", "ahb0_gpu", - "ahb0_ss", "ahb0_sd", "ahb0_nand1", - "ahb0_nand0", "ahb0_sdram", - "ahb0_mipi_hsi", "ahb0_sata", "ahb0_ts", - "ahb0_spi0", "ahb0_spi1", "ahb0_spi2", - "ahb0_spi3"; - }; - - ahb1_gates: clk@06000584 { - #clock-cells = <1>; - compatible = "allwinner,sun9i-a80-ahb1-gates-clk"; - reg = <0x06000584 0x4>; - clocks = <&ahb1>; - clock-indices = <0>, <1>, - <17>, <21>, - <22>, <23>, - <24>; - clock-output-names = "ahb1_usbotg", "ahb1_usbhci", - "ahb1_gmac", "ahb1_msgbox", - "ahb1_spinlock", "ahb1_hstimer", - "ahb1_dma"; - }; - - ahb2_gates: clk@06000588 { - #clock-cells = <1>; - compatible = "allwinner,sun9i-a80-ahb2-gates-clk"; - reg = <0x06000588 0x4>; - clocks = <&ahb2>; - clock-indices = <0>, <1>, - <2>, <4>, <5>, - <7>, <8>, <11>; - clock-output-names = "ahb2_lcd0", "ahb2_lcd1", - "ahb2_edp", "ahb2_csi", "ahb2_hdmi", - "ahb2_de", "ahb2_mp", "ahb2_mipi_dsi"; - }; - - apb0_gates: clk@06000590 { - #clock-cells = <1>; - compatible = "allwinner,sun9i-a80-apb0-gates-clk"; - reg = <0x06000590 0x4>; - clocks = <&apb0>; - clock-indices = <1>, <5>, - <11>, <12>, <13>, - <15>, <17>, <18>, - <19>; - clock-output-names = "apb0_spdif", "apb0_pio", - "apb0_ac97", "apb0_i2s0", "apb0_i2s1", - "apb0_lradc", "apb0_gpadc", "apb0_twd", - "apb0_cirtx"; - }; - - apb1_gates: clk@06000594 { - #clock-cells = <1>; - compatible = "allwinner,sun9i-a80-apb1-gates-clk"; - reg = <0x06000594 0x4>; - clocks = <&apb1>; - clock-indices = <0>, <1>, - <2>, <3>, <4>, - <16>, <17>, - <18>, <19>, - <20>, <21>; - clock-output-names = "apb1_i2c0", "apb1_i2c1", - "apb1_i2c2", "apb1_i2c3", "apb1_i2c4", - "apb1_uart0", "apb1_uart1", - "apb1_uart2", "apb1_uart3", - "apb1_uart4", "apb1_uart5"; - }; - - cpus_clk: clk@08001410 { + cpus_clk: clk@8001410 { compatible = "allwinner,sun9i-a80-cpus-clk"; reg = <0x08001410 0x4>; #clock-cells = <0>; - clocks = <&osc32k>, <&osc24M>, <&pll4>, <&pll3>; + clocks = <&osc32k>, <&osc24M>, + <&ccu CLK_PLL_PERIPH0>, + <&ccu CLK_PLL_AUDIO>; clock-output-names = "cpus"; }; - ahbs: ahbs_clk { + ahbs: clk-ahbs { compatible = "fixed-factor-clock"; #clock-cells = <0>; clock-div = <1>; @@ -394,7 +202,7 @@ clock-output-names = "ahbs"; }; - apbs: clk@0800141c { + apbs: clk@800141c { compatible = "allwinner,sun8i-a23-apb0-clk"; reg = <0x0800141c 0x4>; #clock-cells = <0>; @@ -402,7 +210,7 @@ clock-output-names = "apbs"; }; - apbs_gates: clk@08001428 { + apbs_gates: clk@8001428 { compatible = "allwinner,sun9i-a80-apbs-gates-clk"; reg = <0x08001428 0x4>; #clock-cells = <1>; @@ -423,7 +231,7 @@ "apbs_i2s1", "apbs_twd"; }; - r_1wire_clk: clk@08001450 { + r_1wire_clk: clk@8001450 { reg = <0x08001450 0x4>; #clock-cells = <0>; compatible = "allwinner,sun4i-a10-mod0-clk"; @@ -431,7 +239,7 @@ clock-output-names = "r_1wire"; }; - r_ir_clk: clk@08001454 { + r_ir_clk: clk@8001454 { reg = <0x08001454 0x4>; #clock-cells = <0>; compatible = "allwinner,sun4i-a10-mod0-clk"; @@ -440,6 +248,12 @@ }; }; + de: display-engine { + compatible = "allwinner,sun9i-a80-display-engine"; + allwinner,pipelines = <&fe0>, <&fe1>; + status = "disabled"; + }; + soc { compatible = "simple-bus"; #address-cells = <1>; @@ -450,103 +264,149 @@ */ ranges = <0 0 0 0x20000000>; - ehci0: usb@00a00000 { + sram_b: sram@20000 { + /* 256 KiB secure SRAM at 0x20000 */ + compatible = "mmio-sram"; + reg = <0x00020000 0x40000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x00020000 0x40000>; + + smp-sram@1000 { + /* + * This is checked by BROM to determine if + * cpu0 should jump to SMP entry vector + */ + compatible = "allwinner,sun9i-a80-smp-sram"; + reg = <0x1000 0x8>; + }; + }; + + ehci0: usb@a00000 { compatible = "allwinner,sun9i-a80-ehci", "generic-ehci"; reg = <0x00a00000 0x100>; interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&usb_mod_clk 1>; - resets = <&usb_mod_clk 17>; + clocks = <&usb_clocks CLK_BUS_HCI0>; + resets = <&usb_clocks RST_USB0_HCI>; phys = <&usbphy1>; phy-names = "usb"; status = "disabled"; }; - ohci0: usb@00a00400 { + ohci0: usb@a00400 { compatible = "allwinner,sun9i-a80-ohci", "generic-ohci"; reg = <0x00a00400 0x100>; interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&usb_mod_clk 1>, <&usb_mod_clk 2>; - resets = <&usb_mod_clk 17>; + clocks = <&usb_clocks CLK_BUS_HCI0>, + <&usb_clocks CLK_USB_OHCI0>; + resets = <&usb_clocks RST_USB0_HCI>; phys = <&usbphy1>; phy-names = "usb"; status = "disabled"; }; - usbphy1: phy@00a00800 { + usbphy1: phy@a00800 { compatible = "allwinner,sun9i-a80-usb-phy"; reg = <0x00a00800 0x4>; - clocks = <&usb_phy_clk 1>; + clocks = <&usb_clocks CLK_USB0_PHY>; clock-names = "phy"; - resets = <&usb_phy_clk 17>; + resets = <&usb_clocks RST_USB0_PHY>; reset-names = "phy"; status = "disabled"; #phy-cells = <0>; }; - ehci1: usb@00a01000 { + ehci1: usb@a01000 { compatible = "allwinner,sun9i-a80-ehci", "generic-ehci"; reg = <0x00a01000 0x100>; interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&usb_mod_clk 3>; - resets = <&usb_mod_clk 18>; + clocks = <&usb_clocks CLK_BUS_HCI1>; + resets = <&usb_clocks RST_USB1_HCI>; phys = <&usbphy2>; phy-names = "usb"; status = "disabled"; }; - usbphy2: phy@00a01800 { + usbphy2: phy@a01800 { compatible = "allwinner,sun9i-a80-usb-phy"; reg = <0x00a01800 0x4>; - clocks = <&usb_phy_clk 2>, <&usb_phy_clk 10>, - <&usb_phy_clk 3>; - clock-names = "hsic_480M", "hsic_12M", "phy"; - resets = <&usb_phy_clk 18>, <&usb_phy_clk 19>; - reset-names = "hsic", "phy"; + clocks = <&usb_clocks CLK_USB1_HSIC>, + <&usb_clocks CLK_USB_HSIC>, + <&usb_clocks CLK_USB1_PHY>; + clock-names = "hsic_480M", + "hsic_12M", + "phy"; + resets = <&usb_clocks RST_USB1_HSIC>, + <&usb_clocks RST_USB1_PHY>; + reset-names = "hsic", + "phy"; status = "disabled"; #phy-cells = <0>; /* usb1 is always used with HSIC */ phy_type = "hsic"; }; - ehci2: usb@00a02000 { + ehci2: usb@a02000 { compatible = "allwinner,sun9i-a80-ehci", "generic-ehci"; reg = <0x00a02000 0x100>; interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&usb_mod_clk 5>; - resets = <&usb_mod_clk 19>; + clocks = <&usb_clocks CLK_BUS_HCI2>; + resets = <&usb_clocks RST_USB2_HCI>; phys = <&usbphy3>; phy-names = "usb"; status = "disabled"; }; - ohci2: usb@00a02400 { + ohci2: usb@a02400 { compatible = "allwinner,sun9i-a80-ohci", "generic-ohci"; reg = <0x00a02400 0x100>; interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&usb_mod_clk 5>, <&usb_mod_clk 6>; - resets = <&usb_mod_clk 19>; + clocks = <&usb_clocks CLK_BUS_HCI2>, + <&usb_clocks CLK_USB_OHCI2>; + resets = <&usb_clocks RST_USB2_HCI>; phys = <&usbphy3>; phy-names = "usb"; status = "disabled"; }; - usbphy3: phy@00a02800 { + usbphy3: phy@a02800 { compatible = "allwinner,sun9i-a80-usb-phy"; reg = <0x00a02800 0x4>; - clocks = <&usb_phy_clk 4>, <&usb_phy_clk 10>, - <&usb_phy_clk 5>; - clock-names = "hsic_480M", "hsic_12M", "phy"; - resets = <&usb_phy_clk 20>, <&usb_phy_clk 21>; - reset-names = "hsic", "phy"; + clocks = <&usb_clocks CLK_USB2_HSIC>, + <&usb_clocks CLK_USB_HSIC>, + <&usb_clocks CLK_USB2_PHY>; + clock-names = "hsic_480M", + "hsic_12M", + "phy"; + resets = <&usb_clocks RST_USB2_HSIC>, + <&usb_clocks RST_USB2_PHY>; + reset-names = "hsic", + "phy"; status = "disabled"; #phy-cells = <0>; }; - mmc0: mmc@01c0f000 { + usb_clocks: clock@a08000 { + compatible = "allwinner,sun9i-a80-usb-clks"; + reg = <0x00a08000 0x8>; + clocks = <&ccu CLK_BUS_USB>, <&osc24M>; + clock-names = "bus", "hosc"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + cpucfg@1700000 { + compatible = "allwinner,sun9i-a80-cpucfg"; + reg = <0x01700000 0x100>; + }; + + mmc0: mmc@1c0f000 { compatible = "allwinner,sun9i-a80-mmc"; reg = <0x01c0f000 0x1000>; - clocks = <&mmc_config_clk 0>, <&mmc0_clk 0>, - <&mmc0_clk 1>, <&mmc0_clk 2>; + clocks = <&mmc_config_clk 0>, <&ccu CLK_MMC0>, + <&ccu CLK_MMC0_OUTPUT>, + <&ccu CLK_MMC0_SAMPLE>; clock-names = "ahb", "mmc", "output", "sample"; resets = <&mmc_config_clk 0>; reset-names = "ahb"; @@ -556,11 +416,12 @@ #size-cells = <0>; }; - mmc1: mmc@01c10000 { + mmc1: mmc@1c10000 { compatible = "allwinner,sun9i-a80-mmc"; reg = <0x01c10000 0x1000>; - clocks = <&mmc_config_clk 1>, <&mmc1_clk 0>, - <&mmc1_clk 1>, <&mmc1_clk 2>; + clocks = <&mmc_config_clk 1>, <&ccu CLK_MMC1>, + <&ccu CLK_MMC1_OUTPUT>, + <&ccu CLK_MMC1_SAMPLE>; clock-names = "ahb", "mmc", "output", "sample"; resets = <&mmc_config_clk 1>; reset-names = "ahb"; @@ -570,11 +431,12 @@ #size-cells = <0>; }; - mmc2: mmc@01c11000 { + mmc2: mmc@1c11000 { compatible = "allwinner,sun9i-a80-mmc"; reg = <0x01c11000 0x1000>; - clocks = <&mmc_config_clk 2>, <&mmc2_clk 0>, - <&mmc2_clk 1>, <&mmc2_clk 2>; + clocks = <&mmc_config_clk 2>, <&ccu CLK_MMC2>, + <&ccu CLK_MMC2_OUTPUT>, + <&ccu CLK_MMC2_SAMPLE>; clock-names = "ahb", "mmc", "output", "sample"; resets = <&mmc_config_clk 2>; reset-names = "ahb"; @@ -584,11 +446,12 @@ #size-cells = <0>; }; - mmc3: mmc@01c12000 { + mmc3: mmc@1c12000 { compatible = "allwinner,sun9i-a80-mmc"; reg = <0x01c12000 0x1000>; - clocks = <&mmc_config_clk 3>, <&mmc3_clk 0>, - <&mmc3_clk 1>, <&mmc3_clk 2>; + clocks = <&mmc_config_clk 3>, <&ccu CLK_MMC3>, + <&ccu CLK_MMC3_OUTPUT>, + <&ccu CLK_MMC3_SAMPLE>; clock-names = "ahb", "mmc", "output", "sample"; resets = <&mmc_config_clk 3>; reset-names = "ahb"; @@ -598,12 +461,12 @@ #size-cells = <0>; }; - mmc_config_clk: clk@01c13000 { + mmc_config_clk: clk@1c13000 { compatible = "allwinner,sun9i-a80-mmc-config-clk"; reg = <0x01c13000 0x10>; - clocks = <&ahb0_gates 8>; + clocks = <&ccu CLK_BUS_MMC>; clock-names = "ahb"; - resets = <&ahb0_resets 8>; + resets = <&ccu RST_BUS_MMC>; reset-names = "ahb"; #clock-cells = <1>; #reset-cells = <1>; @@ -611,10 +474,10 @@ "mmc2_config", "mmc3_config"; }; - gic: interrupt-controller@01c41000 { + gic: interrupt-controller@1c41000 { compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; reg = <0x01c41000 0x1000>, - <0x01c42000 0x1000>, + <0x01c42000 0x2000>, <0x01c44000 0x2000>, <0x01c46000 0x2000>; interrupt-controller; @@ -622,37 +485,435 @@ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; }; - ahb0_resets: reset@060005a0 { - #reset-cells = <1>; - compatible = "allwinner,sun6i-a31-clock-reset"; - reg = <0x060005a0 0x4>; + cci: cci@1c90000 { + compatible = "arm,cci-400"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x01c90000 0x1000>; + ranges = <0x0 0x01c90000 0x10000>; + + cci_control0: slave-if@4000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x4000 0x1000>; + }; + + cci_control1: slave-if@5000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x5000 0x1000>; + }; + + pmu@9000 { + compatible = "arm,cci-400-pmu,r1"; + reg = <0x9000 0x5000>; + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; + }; }; - ahb1_resets: reset@060005a4 { + de_clocks: clock@3000000 { + compatible = "allwinner,sun9i-a80-de-clks"; + reg = <0x03000000 0x30>; + clocks = <&ccu CLK_DE>, + <&ccu CLK_SDRAM>, + <&ccu CLK_BUS_DE>; + clock-names = "mod", + "dram", + "bus"; + resets = <&ccu RST_BUS_DE>; + #clock-cells = <1>; #reset-cells = <1>; - compatible = "allwinner,sun6i-a31-clock-reset"; - reg = <0x060005a4 0x4>; }; - ahb2_resets: reset@060005a8 { - #reset-cells = <1>; - compatible = "allwinner,sun6i-a31-clock-reset"; - reg = <0x060005a8 0x4>; + fe0: display-frontend@3100000 { + compatible = "allwinner,sun9i-a80-display-frontend"; + reg = <0x03100000 0x40000>; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&de_clocks CLK_BUS_FE0>, <&de_clocks CLK_FE0>, + <&de_clocks CLK_DRAM_FE0>; + clock-names = "ahb", "mod", + "ram"; + resets = <&de_clocks RST_FE0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + fe0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + fe0_out_deu0: endpoint@0 { + reg = <0>; + remote-endpoint = <&deu0_in_fe0>; + }; + }; + }; }; - apb0_resets: reset@060005b0 { - #reset-cells = <1>; - compatible = "allwinner,sun6i-a31-clock-reset"; - reg = <0x060005b0 0x4>; + fe1: display-frontend@3140000 { + compatible = "allwinner,sun9i-a80-display-frontend"; + reg = <0x03140000 0x40000>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&de_clocks CLK_BUS_FE1>, <&de_clocks CLK_FE1>, + <&de_clocks CLK_DRAM_FE1>; + clock-names = "ahb", "mod", + "ram"; + resets = <&de_clocks RST_FE0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + fe1_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + fe1_out_deu1: endpoint@0 { + reg = <0>; + remote-endpoint = <&deu1_in_fe1>; + }; + }; + }; + }; + + be0: display-backend@3200000 { + compatible = "allwinner,sun9i-a80-display-backend"; + reg = <0x03200000 0x40000>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&de_clocks CLK_BUS_BE0>, <&de_clocks CLK_BE0>, + <&de_clocks CLK_DRAM_BE0>; + clock-names = "ahb", "mod", + "ram"; + resets = <&de_clocks RST_BE0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + be0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + be0_in_deu0: endpoint@0 { + reg = <0>; + remote-endpoint = <&deu0_out_be0>; + }; + + be0_in_deu1: endpoint@1 { + reg = <1>; + remote-endpoint = <&deu1_out_be0>; + }; + }; + + be0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + be0_out_drc0: endpoint@0 { + reg = <0>; + remote-endpoint = <&drc0_in_be0>; + }; + }; + }; + }; + + be1: display-backend@3240000 { + compatible = "allwinner,sun9i-a80-display-backend"; + reg = <0x03240000 0x40000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&de_clocks CLK_BUS_BE1>, <&de_clocks CLK_BE1>, + <&de_clocks CLK_DRAM_BE1>; + clock-names = "ahb", "mod", + "ram"; + resets = <&de_clocks RST_BE1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + be1_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + be1_in_deu0: endpoint@0 { + reg = <0>; + remote-endpoint = <&deu0_out_be1>; + }; + + be1_in_deu1: endpoint@1 { + reg = <1>; + remote-endpoint = <&deu1_out_be1>; + }; + }; + + be1_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + be1_out_drc1: endpoint@0 { + reg = <0>; + remote-endpoint = <&drc1_in_be1>; + }; + }; + }; + }; + + deu0: deu@3300000 { + compatible = "allwinner,sun9i-a80-deu"; + reg = <0x03300000 0x40000>; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&de_clocks CLK_BUS_DEU0>, + <&de_clocks CLK_IEP_DEU0>, + <&de_clocks CLK_DRAM_DEU0>; + clock-names = "ahb", + "mod", + "ram"; + resets = <&de_clocks RST_DEU0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + deu0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + deu0_in_fe0: endpoint@0 { + reg = <0>; + remote-endpoint = <&fe0_out_deu0>; + }; + }; + + deu0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + deu0_out_be0: endpoint@0 { + reg = <0>; + remote-endpoint = <&be0_in_deu0>; + }; + + deu0_out_be1: endpoint@1 { + reg = <1>; + remote-endpoint = <&be1_in_deu0>; + }; + }; + }; + }; + + deu1: deu@3340000 { + compatible = "allwinner,sun9i-a80-deu"; + reg = <0x03340000 0x40000>; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&de_clocks CLK_BUS_DEU1>, + <&de_clocks CLK_IEP_DEU1>, + <&de_clocks CLK_DRAM_DEU1>; + clock-names = "ahb", + "mod", + "ram"; + resets = <&de_clocks RST_DEU1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + deu1_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + deu1_in_fe1: endpoint@0 { + reg = <0>; + remote-endpoint = <&fe1_out_deu1>; + }; + }; + + deu1_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + deu1_out_be0: endpoint@0 { + reg = <0>; + remote-endpoint = <&be0_in_deu1>; + }; + + deu1_out_be1: endpoint@1 { + reg = <1>; + remote-endpoint = <&be1_in_deu1>; + }; + }; + }; + }; + + drc0: drc@3400000 { + compatible = "allwinner,sun9i-a80-drc"; + reg = <0x03400000 0x40000>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&de_clocks CLK_BUS_DRC0>, + <&de_clocks CLK_IEP_DRC0>, + <&de_clocks CLK_DRAM_DRC0>; + clock-names = "ahb", + "mod", + "ram"; + resets = <&de_clocks RST_DRC0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + drc0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + drc0_in_be0: endpoint@0 { + reg = <0>; + remote-endpoint = <&be0_out_drc0>; + }; + }; + + drc0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + drc0_out_tcon0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_in_drc0>; + }; + }; + }; + }; + + drc1: drc@3440000 { + compatible = "allwinner,sun9i-a80-drc"; + reg = <0x03440000 0x40000>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&de_clocks CLK_BUS_DRC1>, + <&de_clocks CLK_IEP_DRC1>, + <&de_clocks CLK_DRAM_DRC1>; + clock-names = "ahb", + "mod", + "ram"; + resets = <&de_clocks RST_DRC1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + drc1_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + drc1_in_be1: endpoint@0 { + reg = <0>; + remote-endpoint = <&be1_out_drc1>; + }; + }; + + drc1_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + drc1_out_tcon1: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon1_in_drc1>; + }; + }; + }; + }; + + tcon0: lcd-controller@3c00000 { + compatible = "allwinner,sun9i-a80-tcon-lcd"; + reg = <0x03c00000 0x10000>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_LCD0>, <&ccu CLK_LCD0>; + clock-names = "ahb", "tcon-ch0"; + resets = <&ccu RST_BUS_LCD0>, <&ccu RST_BUS_EDP>; + reset-names = "lcd", "edp"; + clock-output-names = "tcon0-pixel-clock"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + tcon0_in_drc0: endpoint@0 { + reg = <0>; + remote-endpoint = <&drc0_out_tcon0>; + }; + }; + + tcon0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + }; }; - apb1_resets: reset@060005b4 { + tcon1: lcd-controller@3c10000 { + compatible = "allwinner,sun9i-a80-tcon-tv"; + reg = <0x03c10000 0x10000>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_LCD1>, <&ccu CLK_LCD1>; + clock-names = "ahb", "tcon-ch1"; + resets = <&ccu RST_BUS_LCD1>, <&ccu RST_BUS_EDP>; + reset-names = "lcd", "edp"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon1_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + tcon1_in_drc1: endpoint@0 { + reg = <0>; + remote-endpoint = <&drc1_out_tcon1>; + }; + }; + + tcon1_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + }; + }; + + ccu: clock@6000000 { + compatible = "allwinner,sun9i-a80-ccu"; + reg = <0x06000000 0x800>; + clocks = <&osc24M>, <&osc32k>; + clock-names = "hosc", "losc"; + #clock-cells = <1>; #reset-cells = <1>; - compatible = "allwinner,sun6i-a31-clock-reset"; - reg = <0x060005b4 0x4>; }; - timer@06000c00 { + timer@6000c00 { compatible = "allwinner,sun4i-a10-timer"; reg = <0x06000c00 0xa0>; interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, @@ -665,13 +926,13 @@ clocks = <&osc24M>; }; - wdt: watchdog@06000ca0 { + wdt: watchdog@6000ca0 { compatible = "allwinner,sun6i-a31-wdt"; reg = <0x06000ca0 0x20>; interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; }; - pio: pinctrl@06000800 { + pio: pinctrl@6000800 { compatible = "allwinner,sun9i-a80-pinctrl"; reg = <0x06000800 0x400>; interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, @@ -679,195 +940,206 @@ <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&apb0_gates 5>; + clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>; + clock-names = "apb", "hosc", "losc"; gpio-controller; interrupt-controller; #interrupt-cells = <3>; #size-cells = <0>; #gpio-cells = <3>; - i2c3_pins_a: i2c3@0 { - allwinner,pins = "PG10", "PG11"; - allwinner,function = "i2c3"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + i2c3_pins: i2c3-pins { + pins = "PG10", "PG11"; + function = "i2c3"; + }; + + lcd0_rgb888_pins: lcd0-rgb888-pins { + pins = "PD0", "PD1", "PD2", "PD3", + "PD4", "PD5", "PD6", "PD7", + "PD8", "PD9", "PD10", "PD11", + "PD12", "PD13", "PD14", "PD15", + "PD16", "PD17", "PD18", "PD19", + "PD20", "PD21", "PD22", "PD23", + "PD24", "PD25", "PD26", "PD27"; + function = "lcd0"; }; - mmc0_pins: mmc0 { - allwinner,pins = "PF0", "PF1" ,"PF2", "PF3", - "PF4", "PF5"; - allwinner,function = "mmc0"; - allwinner,drive = <SUN4I_PINCTRL_30_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + mmc0_pins: mmc0-pins { + pins = "PF0", "PF1" ,"PF2", "PF3", + "PF4", "PF5"; + function = "mmc0"; + drive-strength = <30>; + bias-pull-up; }; - mmc1_pins: mmc1 { - allwinner,pins = "PG0", "PG1" ,"PG2", "PG3", + mmc1_pins: mmc1-pins { + pins = "PG0", "PG1" ,"PG2", "PG3", "PG4", "PG5"; - allwinner,function = "mmc1"; - allwinner,drive = <SUN4I_PINCTRL_30_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + function = "mmc1"; + drive-strength = <30>; + bias-pull-up; }; - mmc2_8bit_pins: mmc2_8bit { - allwinner,pins = "PC6", "PC7", "PC8", "PC9", - "PC10", "PC11", "PC12", - "PC13", "PC14", "PC15", - "PC16"; - allwinner,function = "mmc2"; - allwinner,drive = <SUN4I_PINCTRL_30_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + mmc2_8bit_pins: mmc2-8bit-pins { + pins = "PC6", "PC7", "PC8", "PC9", + "PC10", "PC11", "PC12", + "PC13", "PC14", "PC15", + "PC16"; + function = "mmc2"; + drive-strength = <30>; + bias-pull-up; }; - uart0_pins_a: uart0@0 { - allwinner,pins = "PH12", "PH13"; - allwinner,function = "uart0"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + uart0_ph_pins: uart0-ph-pins { + pins = "PH12", "PH13"; + function = "uart0"; }; - uart4_pins_a: uart4@0 { - allwinner,pins = "PG12", "PG13", "PG14", "PG15"; - allwinner,function = "uart4"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + uart4_pins: uart4-pins { + pins = "PG12", "PG13", "PG14", "PG15"; + function = "uart4"; }; }; - uart0: serial@07000000 { + uart0: serial@7000000 { compatible = "snps,dw-apb-uart"; reg = <0x07000000 0x400>; interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; - clocks = <&apb1_gates 16>; - resets = <&apb1_resets 16>; + clocks = <&ccu CLK_BUS_UART0>; + resets = <&ccu RST_BUS_UART0>; status = "disabled"; }; - uart1: serial@07000400 { + uart1: serial@7000400 { compatible = "snps,dw-apb-uart"; reg = <0x07000400 0x400>; interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; - clocks = <&apb1_gates 17>; - resets = <&apb1_resets 17>; + clocks = <&ccu CLK_BUS_UART1>; + resets = <&ccu RST_BUS_UART1>; status = "disabled"; }; - uart2: serial@07000800 { + uart2: serial@7000800 { compatible = "snps,dw-apb-uart"; reg = <0x07000800 0x400>; interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; - clocks = <&apb1_gates 18>; - resets = <&apb1_resets 18>; + clocks = <&ccu CLK_BUS_UART2>; + resets = <&ccu RST_BUS_UART2>; status = "disabled"; }; - uart3: serial@07000c00 { + uart3: serial@7000c00 { compatible = "snps,dw-apb-uart"; reg = <0x07000c00 0x400>; interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; - clocks = <&apb1_gates 19>; - resets = <&apb1_resets 19>; + clocks = <&ccu CLK_BUS_UART3>; + resets = <&ccu RST_BUS_UART3>; status = "disabled"; }; - uart4: serial@07001000 { + uart4: serial@7001000 { compatible = "snps,dw-apb-uart"; reg = <0x07001000 0x400>; interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; - clocks = <&apb1_gates 20>; - resets = <&apb1_resets 20>; + clocks = <&ccu CLK_BUS_UART4>; + resets = <&ccu RST_BUS_UART4>; status = "disabled"; }; - uart5: serial@07001400 { + uart5: serial@7001400 { compatible = "snps,dw-apb-uart"; reg = <0x07001400 0x400>; interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; - clocks = <&apb1_gates 21>; - resets = <&apb1_resets 21>; + clocks = <&ccu CLK_BUS_UART5>; + resets = <&ccu RST_BUS_UART5>; status = "disabled"; }; - i2c0: i2c@07002800 { + i2c0: i2c@7002800 { compatible = "allwinner,sun6i-a31-i2c"; reg = <0x07002800 0x400>; interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&apb1_gates 0>; - resets = <&apb1_resets 0>; + clocks = <&ccu CLK_BUS_I2C0>; + resets = <&ccu RST_BUS_I2C0>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; }; - i2c1: i2c@07002c00 { + i2c1: i2c@7002c00 { compatible = "allwinner,sun6i-a31-i2c"; reg = <0x07002c00 0x400>; interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&apb1_gates 1>; - resets = <&apb1_resets 1>; + clocks = <&ccu CLK_BUS_I2C1>; + resets = <&ccu RST_BUS_I2C1>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; }; - i2c2: i2c@07003000 { + i2c2: i2c@7003000 { compatible = "allwinner,sun6i-a31-i2c"; reg = <0x07003000 0x400>; interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&apb1_gates 2>; - resets = <&apb1_resets 2>; + clocks = <&ccu CLK_BUS_I2C2>; + resets = <&ccu RST_BUS_I2C2>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; }; - i2c3: i2c@07003400 { + i2c3: i2c@7003400 { compatible = "allwinner,sun6i-a31-i2c"; reg = <0x07003400 0x400>; interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&apb1_gates 3>; - resets = <&apb1_resets 3>; + clocks = <&ccu CLK_BUS_I2C3>; + resets = <&ccu RST_BUS_I2C3>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; }; - i2c4: i2c@07003800 { + i2c4: i2c@7003800 { compatible = "allwinner,sun6i-a31-i2c"; reg = <0x07003800 0x400>; interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&apb1_gates 4>; - resets = <&apb1_resets 4>; + clocks = <&ccu CLK_BUS_I2C4>; + resets = <&ccu RST_BUS_I2C4>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; }; - r_wdt: watchdog@08001000 { + r_wdt: watchdog@8001000 { compatible = "allwinner,sun6i-a31-wdt"; reg = <0x08001000 0x20>; interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; }; - apbs_rst: reset@080014b0 { + prcm@8001400 { + compatible = "allwinner,sun9i-a80-prcm"; + reg = <0x08001400 0x200>; + }; + + apbs_rst: reset@80014b0 { reg = <0x080014b0 0x4>; compatible = "allwinner,sun6i-a31-clock-reset"; #reset-cells = <1>; }; - nmi_intc: interrupt-controller@080015a0 { + nmi_intc: interrupt-controller@80015a0 { compatible = "allwinner,sun9i-a80-nmi"; interrupt-controller; #interrupt-cells = <2>; @@ -875,7 +1147,7 @@ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; }; - r_ir: ir@08002000 { + r_ir: ir@8002000 { compatible = "allwinner,sun5i-a13-ir"; interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; @@ -887,7 +1159,7 @@ status = "disabled"; }; - r_uart: serial@08002800 { + r_uart: serial@8002800 { compatible = "snps,dw-apb-uart"; reg = <0x08002800 0x400>; interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; @@ -898,35 +1170,33 @@ status = "disabled"; }; - r_pio: pinctrl@08002c00 { + r_pio: pinctrl@8002c00 { compatible = "allwinner,sun9i-a80-r-pinctrl"; reg = <0x08002c00 0x400>; interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&apbs_gates 0>; + clocks = <&apbs_gates 0>, <&osc24M>, <&osc32k>; + clock-names = "apb", "hosc", "losc"; resets = <&apbs_rst 0>; gpio-controller; interrupt-controller; - #address-cells = <1>; - #size-cells = <0>; + #interrupt-cells = <3>; #gpio-cells = <3>; - r_ir_pins: r_ir { - allwinner,pins = "PL6"; - allwinner,function = "s_cir_rx"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + r_ir_pins: r-ir-pins { + pins = "PL6"; + function = "s_cir_rx"; }; - r_rsb_pins: r_rsb { - allwinner,pins = "PN0", "PN1"; - allwinner,function = "s_rsb"; - allwinner,drive = <SUN4I_PINCTRL_20_MA>; - allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + r_rsb_pins: r-rsb-pins { + pins = "PN0", "PN1"; + function = "s_rsb"; + drive-strength = <20>; + bias-pull-up; }; }; - r_rsb: i2c@08003400 { + r_rsb: i2c@8003400 { compatible = "allwinner,sun8i-a23-rsb"; reg = <0x08003400 0x400>; interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; diff --git a/include/dt-bindings/clock/sun9i-a80-ccu.h b/include/dt-bindings/clock/sun9i-a80-ccu.h new file mode 100644 index 0000000000..6ea1492a73 --- /dev/null +++ b/include/dt-bindings/clock/sun9i-a80-ccu.h @@ -0,0 +1,162 @@ +/* + * Copyright (C) 2016 Chen-Yu Tsai <wens(a)csie.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#ifndef _DT_BINDINGS_CLOCK_SUN9I_A80_CCU_H_ +#define _DT_BINDINGS_CLOCK_SUN9I_A80_CCU_H_ + +#define CLK_PLL_AUDIO 2 +#define CLK_PLL_PERIPH0 3 + +#define CLK_C0CPUX 12 +#define CLK_C1CPUX 13 + +#define CLK_OUT_A 27 +#define CLK_OUT_B 28 + +#define CLK_NAND0_0 29 +#define CLK_NAND0_1 30 +#define CLK_NAND1_0 31 +#define CLK_NAND1_1 32 +#define CLK_MMC0 33 +#define CLK_MMC0_SAMPLE 34 +#define CLK_MMC0_OUTPUT 35 +#define CLK_MMC1 36 +#define CLK_MMC1_SAMPLE 37 +#define CLK_MMC1_OUTPUT 38 +#define CLK_MMC2 39 +#define CLK_MMC2_SAMPLE 40 +#define CLK_MMC2_OUTPUT 41 +#define CLK_MMC3 42 +#define CLK_MMC3_SAMPLE 43 +#define CLK_MMC3_OUTPUT 44 +#define CLK_TS 45 +#define CLK_SS 46 +#define CLK_SPI0 47 +#define CLK_SPI1 48 +#define CLK_SPI2 49 +#define CLK_SPI3 50 +#define CLK_I2S0 51 +#define CLK_I2S1 52 +#define CLK_SPDIF 53 +#define CLK_SDRAM 54 +#define CLK_DE 55 +#define CLK_EDP 56 +#define CLK_MP 57 +#define CLK_LCD0 58 +#define CLK_LCD1 59 +#define CLK_MIPI_DSI0 60 +#define CLK_MIPI_DSI1 61 +#define CLK_HDMI 62 +#define CLK_HDMI_SLOW 63 +#define CLK_MIPI_CSI 64 +#define CLK_CSI_ISP 65 +#define CLK_CSI_MISC 66 +#define CLK_CSI0_MCLK 67 +#define CLK_CSI1_MCLK 68 +#define CLK_FD 69 +#define CLK_VE 70 +#define CLK_AVS 71 +#define CLK_GPU_CORE 72 +#define CLK_GPU_MEMORY 73 +#define CLK_GPU_AXI 74 +#define CLK_SATA 75 +#define CLK_AC97 76 +#define CLK_MIPI_HSI 77 +#define CLK_GPADC 78 +#define CLK_CIR_TX 79 + +#define CLK_BUS_FD 80 +#define CLK_BUS_VE 81 +#define CLK_BUS_GPU_CTRL 82 +#define CLK_BUS_SS 83 +#define CLK_BUS_MMC 84 +#define CLK_BUS_NAND0 85 +#define CLK_BUS_NAND1 86 +#define CLK_BUS_SDRAM 87 +#define CLK_BUS_MIPI_HSI 88 +#define CLK_BUS_SATA 89 +#define CLK_BUS_TS 90 +#define CLK_BUS_SPI0 91 +#define CLK_BUS_SPI1 92 +#define CLK_BUS_SPI2 93 +#define CLK_BUS_SPI3 94 + +#define CLK_BUS_OTG 95 +#define CLK_BUS_USB 96 +#define CLK_BUS_GMAC 97 +#define CLK_BUS_MSGBOX 98 +#define CLK_BUS_SPINLOCK 99 +#define CLK_BUS_HSTIMER 100 +#define CLK_BUS_DMA 101 + +#define CLK_BUS_LCD0 102 +#define CLK_BUS_LCD1 103 +#define CLK_BUS_EDP 104 +#define CLK_BUS_CSI 105 +#define CLK_BUS_HDMI 106 +#define CLK_BUS_DE 107 +#define CLK_BUS_MP 108 +#define CLK_BUS_MIPI_DSI 109 + +#define CLK_BUS_SPDIF 110 +#define CLK_BUS_PIO 111 +#define CLK_BUS_AC97 112 +#define CLK_BUS_I2S0 113 +#define CLK_BUS_I2S1 114 +#define CLK_BUS_LRADC 115 +#define CLK_BUS_GPADC 116 +#define CLK_BUS_TWD 117 +#define CLK_BUS_CIR_TX 118 + +#define CLK_BUS_I2C0 119 +#define CLK_BUS_I2C1 120 +#define CLK_BUS_I2C2 121 +#define CLK_BUS_I2C3 122 +#define CLK_BUS_I2C4 123 +#define CLK_BUS_UART0 124 +#define CLK_BUS_UART1 125 +#define CLK_BUS_UART2 126 +#define CLK_BUS_UART3 127 +#define CLK_BUS_UART4 128 +#define CLK_BUS_UART5 129 + +#endif /* _DT_BINDINGS_CLOCK_SUN9I_A80_CCU_H_ */ diff --git a/include/dt-bindings/clock/sun9i-a80-de.h b/include/dt-bindings/clock/sun9i-a80-de.h new file mode 100644 index 0000000000..3dad6c3cd1 --- /dev/null +++ b/include/dt-bindings/clock/sun9i-a80-de.h @@ -0,0 +1,80 @@ +/* + * Copyright (C) 2016 Chen-Yu Tsai <wens(a)csie.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#ifndef _DT_BINDINGS_CLOCK_SUN9I_A80_DE_H_ +#define _DT_BINDINGS_CLOCK_SUN9I_A80_DE_H_ + +#define CLK_FE0 0 +#define CLK_FE1 1 +#define CLK_FE2 2 +#define CLK_IEP_DEU0 3 +#define CLK_IEP_DEU1 4 +#define CLK_BE0 5 +#define CLK_BE1 6 +#define CLK_BE2 7 +#define CLK_IEP_DRC0 8 +#define CLK_IEP_DRC1 9 +#define CLK_MERGE 10 + +#define CLK_DRAM_FE0 11 +#define CLK_DRAM_FE1 12 +#define CLK_DRAM_FE2 13 +#define CLK_DRAM_DEU0 14 +#define CLK_DRAM_DEU1 15 +#define CLK_DRAM_BE0 16 +#define CLK_DRAM_BE1 17 +#define CLK_DRAM_BE2 18 +#define CLK_DRAM_DRC0 19 +#define CLK_DRAM_DRC1 20 + +#define CLK_BUS_FE0 21 +#define CLK_BUS_FE1 22 +#define CLK_BUS_FE2 23 +#define CLK_BUS_DEU0 24 +#define CLK_BUS_DEU1 25 +#define CLK_BUS_BE0 26 +#define CLK_BUS_BE1 27 +#define CLK_BUS_BE2 28 +#define CLK_BUS_DRC0 29 +#define CLK_BUS_DRC1 30 + +#endif /* _DT_BINDINGS_CLOCK_SUN9I_A80_DE_H_ */ diff --git a/include/dt-bindings/clock/sun9i-a80-usb.h b/include/dt-bindings/clock/sun9i-a80-usb.h new file mode 100644 index 0000000000..783a60d2cc --- /dev/null +++ b/include/dt-bindings/clock/sun9i-a80-usb.h @@ -0,0 +1,59 @@ +/* + * Copyright (C) 2016 Chen-Yu Tsai <wens(a)csie.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#ifndef _DT_BINDINGS_CLOCK_SUN9I_A80_USB_H_ +#define _DT_BINDINGS_CLOCK_SUN9I_A80_USB_H_ + +#define CLK_BUS_HCI0 0 +#define CLK_USB_OHCI0 1 +#define CLK_BUS_HCI1 2 +#define CLK_BUS_HCI2 3 +#define CLK_USB_OHCI2 4 + +#define CLK_USB0_PHY 5 +#define CLK_USB1_HSIC 6 +#define CLK_USB1_PHY 7 +#define CLK_USB2_HSIC 8 +#define CLK_USB2_PHY 9 +#define CLK_USB_HSIC 10 + +#endif /* _DT_BINDINGS_CLOCK_SUN9I_A80_USB_H_ */ diff --git a/include/dt-bindings/reset/sun9i-a80-ccu.h b/include/dt-bindings/reset/sun9i-a80-ccu.h new file mode 100644 index 0000000000..4b8df4b367 --- /dev/null +++ b/include/dt-bindings/reset/sun9i-a80-ccu.h @@ -0,0 +1,102 @@ +/* + * Copyright (C) 2016 Chen-Yu Tsai <wens(a)csie.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#ifndef _DT_BINDINGS_RESET_SUN9I_A80_CCU_H_ +#define _DT_BINDINGS_RESET_SUN9I_A80_CCU_H_ + +#define RST_BUS_FD 0 +#define RST_BUS_VE 1 +#define RST_BUS_GPU_CTRL 2 +#define RST_BUS_SS 3 +#define RST_BUS_MMC 4 +#define RST_BUS_NAND0 5 +#define RST_BUS_NAND1 6 +#define RST_BUS_SDRAM 7 +#define RST_BUS_SATA 8 +#define RST_BUS_TS 9 +#define RST_BUS_SPI0 10 +#define RST_BUS_SPI1 11 +#define RST_BUS_SPI2 12 +#define RST_BUS_SPI3 13 + +#define RST_BUS_OTG 14 +#define RST_BUS_OTG_PHY 15 +#define RST_BUS_MIPI_HSI 16 +#define RST_BUS_GMAC 17 +#define RST_BUS_MSGBOX 18 +#define RST_BUS_SPINLOCK 19 +#define RST_BUS_HSTIMER 20 +#define RST_BUS_DMA 21 + +#define RST_BUS_LCD0 22 +#define RST_BUS_LCD1 23 +#define RST_BUS_EDP 24 +#define RST_BUS_LVDS 25 +#define RST_BUS_CSI 26 +#define RST_BUS_HDMI0 27 +#define RST_BUS_HDMI1 28 +#define RST_BUS_DE 29 +#define RST_BUS_MP 30 +#define RST_BUS_GPU 31 +#define RST_BUS_MIPI_DSI 32 + +#define RST_BUS_SPDIF 33 +#define RST_BUS_AC97 34 +#define RST_BUS_I2S0 35 +#define RST_BUS_I2S1 36 +#define RST_BUS_LRADC 37 +#define RST_BUS_GPADC 38 +#define RST_BUS_CIR_TX 39 + +#define RST_BUS_I2C0 40 +#define RST_BUS_I2C1 41 +#define RST_BUS_I2C2 42 +#define RST_BUS_I2C3 43 +#define RST_BUS_I2C4 44 +#define RST_BUS_UART0 45 +#define RST_BUS_UART1 46 +#define RST_BUS_UART2 47 +#define RST_BUS_UART3 48 +#define RST_BUS_UART4 49 +#define RST_BUS_UART5 50 + +#endif /* _DT_BINDINGS_RESET_SUN9I_A80_CCU_H_ */ diff --git a/include/dt-bindings/reset/sun9i-a80-de.h b/include/dt-bindings/reset/sun9i-a80-de.h new file mode 100644 index 0000000000..2050727701 --- /dev/null +++ b/include/dt-bindings/reset/sun9i-a80-de.h @@ -0,0 +1,58 @@ +/* + * Copyright (C) 2016 Chen-Yu Tsai <wens(a)csie.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#ifndef _DT_BINDINGS_RESET_SUN9I_A80_DE_H_ +#define _DT_BINDINGS_RESET_SUN9I_A80_DE_H_ + +#define RST_FE0 0 +#define RST_FE1 1 +#define RST_FE2 2 +#define RST_DEU0 3 +#define RST_DEU1 4 +#define RST_BE0 5 +#define RST_BE1 6 +#define RST_BE2 7 +#define RST_DRC0 8 +#define RST_DRC1 9 +#define RST_MERGE 10 + +#endif /* _DT_BINDINGS_RESET_SUN9I_A80_DE_H_ */ diff --git a/include/dt-bindings/reset/sun9i-a80-usb.h b/include/dt-bindings/reset/sun9i-a80-usb.h new file mode 100644 index 0000000000..ee492864c2 --- /dev/null +++ b/include/dt-bindings/reset/sun9i-a80-usb.h @@ -0,0 +1,56 @@ +/* + * Copyright (C) 2016 Chen-Yu Tsai <wens(a)csie.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#ifndef _DT_BINDINGS_RESET_SUN9I_A80_USB_H_ +#define _DT_BINDINGS_RESET_SUN9I_A80_USB_H_ + +#define RST_USB0_HCI 0 +#define RST_USB1_HCI 1 +#define RST_USB2_HCI 2 + +#define RST_USB0_PHY 3 +#define RST_USB1_HSIC 4 +#define RST_USB1_PHY 5 +#define RST_USB2_HSIC 6 +#define RST_USB2_PHY 7 + +#endif /* _DT_BINDINGS_RESET_SUN9I_A80_USB_H_ */ -- 2.18.0.321.gffc6fa0e3

3 5

[U-Boot] Please pull u-boot-fsl-qoriq master
by York Sun 19 Jan '19

19 Jan '19

Tom, The following changes since commit d3689267f92c5956e09cc7d1baa4700141662bff: Prepare v2019.01 (2019-01-14 17:02:36 -0500) are available in the Git repository at: git://git.denx.de/u-boot-fsl-qoriq.git tags/fsl-qoriq-for-v2019.04-rc1 for you to fetch changes up to a200ebea630002b14def4a015642fa341dc9cd11: armv8: ls2088ardb: Update MAINTAINERS (2019-01-17 13:17:51 -0800) ---------------------------------------------------------------- Add TFA boot flow for more boards Add TFA boot defconfig for ls1088a and ls2088a. Add dts fixup for PCIe endpoint and root complex. Travis build log is https://travis-ci.org/yorksun/u-boot/builds/481076641 ---------------------------------------------------------------- Florinel Iordache (1): ls1046aqds: Bypass xfi port fixup for KR mode Hou Zhiqiang (2): armv8: ls1043a: add SVR definitions for 23x23 package silicon armv8: ls1043a: correct the PCIe INTx fixup Laurentiu Tudor (1): armv8: fsl-layerscape: properly configure qdma ICID Mian Yousaf Kaukab (1): fsl-layerscape: dpaa: fix fsl-mc status in fdt with bootefi Pankit Garg (3): ls1043a: add support for nand-boot cmd for TFA armv8: ls1088ardb: Add TFABOOT support armv8: ls1088aqds: Add TFABOOT support Rajesh Bhagat (7): armv8: fsl-layerscape: fixes for TFABOOT framework drivers: ifc: restore the legacy flow for IFC config armv8: ls2088ardb: Add TFABOOT support armv8: ls2088aqds: Add TFABOOT support env: fix allow to build multiple environments configs: update TFABOOT defconfigs for SD boot support armv7: dts: ls1021a: Remove aliases property name warning Xiaowei Bao (3): pci: layerscape: Modify the EP and RC mode judge method pci: layerscape: Do not scan when PEX work in EP mode pci: layerscape: Add the dts fixup for EP and RC Yinbo Zhu (1): mmc: fsl_esdhc: make get_cd work well in dm_mmc_ops York Sun (2): armv8: ls1088ardb: Update MAINTAINERS armv8: ls2088ardb: Update MAINTAINERS arch/arm/cpu/armv8/fsl-layerscape/Kconfig | 26 +-- arch/arm/cpu/armv8/fsl-layerscape/cpu.c | 4 +- arch/arm/cpu/armv8/fsl-layerscape/fdt.c | 2 +- arch/arm/cpu/armv8/fsl-layerscape/soc.c | 13 +- arch/arm/dts/fsl-ls2088a-rdb-qspi.dts | 4 + arch/arm/dts/ls1021a-iot.dtsi | 6 +- arch/arm/dts/ls1021a-qds.dtsi | 10 +- arch/arm/dts/ls1021a-twr.dtsi | 6 +- .../arm/include/asm/arch-fsl-layerscape/fsl_icid.h | 6 +- .../include/asm/arch-fsl-layerscape/immap_lsch2.h | 1 + arch/arm/include/asm/arch-fsl-layerscape/soc.h | 3 + board/freescale/ls1046aqds/eth.c | 35 ++-- board/freescale/ls1088a/MAINTAINERS | 5 + board/freescale/ls1088a/ddr.c | 11 ++ board/freescale/ls1088a/ls1088a.c | 196 ++++++++++++++++++++- board/freescale/ls2080a/ls2080a.c | 10 +- board/freescale/ls2080aqds/MAINTAINERS | 2 + board/freescale/ls2080aqds/ddr.c | 12 ++ board/freescale/ls2080aqds/ls2080aqds.c | 3 +- board/freescale/ls2080ardb/MAINTAINERS | 3 + board/freescale/ls2080ardb/ddr.c | 12 ++ board/freescale/ls2080ardb/ls2080ardb.c | 40 ++++- configs/ls1043aqds_tfa_defconfig | 1 + configs/ls1043ardb_tfa_defconfig | 1 + configs/ls1046aqds_tfa_defconfig | 1 + configs/ls1046ardb_tfa_defconfig | 1 + configs/ls1088aqds_tfa_defconfig | 70 ++++++++ configs/ls1088ardb_tfa_SECURE_BOOT_defconfig | 64 +++++++ configs/ls1088ardb_tfa_defconfig | 62 +++++++ configs/ls2088aqds_tfa_defconfig | 64 +++++++ configs/ls2088ardb_tfa_SECURE_BOOT_defconfig | 74 ++++++++ configs/ls2088ardb_tfa_defconfig | 73 ++++++++ drivers/misc/fsl_ifc.c | 173 ++++++++++++++++++ drivers/mmc/fsl_esdhc.c | 1 - drivers/net/fsl-mc/mc.c | 5 + drivers/pci/pcie_layerscape.c | 21 +-- drivers/pci/pcie_layerscape.h | 1 + drivers/pci/pcie_layerscape_fixup.c | 25 ++- include/configs/ls1043a_common.h | 2 + include/configs/ls1088a_common.h | 11 +- include/configs/ls1088aqds.h | 99 ++++++++++- include/configs/ls1088ardb.h | 137 +++++++++++++- include/configs/ls2080a_common.h | 8 + include/configs/ls2080aqds.h | 40 ++++- include/configs/ls2080ardb.h | 137 +++++++++++++- include/environment.h | 9 - include/fsl-mc/fsl_mc.h | 1 + include/mmc.h | 3 + 48 files changed, 1420 insertions(+), 74 deletions(-) create mode 100644 configs/ls1088aqds_tfa_defconfig create mode 100644 configs/ls1088ardb_tfa_SECURE_BOOT_defconfig create mode 100644 configs/ls1088ardb_tfa_defconfig create mode 100644 configs/ls2088aqds_tfa_defconfig create mode 100644 configs/ls2088ardb_tfa_SECURE_BOOT_defconfig create mode 100644 configs/ls2088ardb_tfa_defconfig Thanks. York

2 1

[U-Boot] [PATCH v2 0/7] mmc: sunxi: Enable DM_MMC
by Jagan Teki 19 Jan '19

19 Jan '19

V2 for previous version[1] changes, for enabling DM_MMC on Allwinner platform. Changes for v2: - update the 'reset enablement' logic to do required SoC's Note: All changes available at u-boot-sunxi/next [1] https://patchwork.ozlabs.org/cover/1023710/ Any comments? Jagan. Jagan Teki (7): mmc: sunxi: Configure reset support for DM_MMC mmc: sunxi: Add A83T emmc compatible mmc: sunxi: Add mmc, emmc H5/A64 compatible mmc: sunxi: Add DM_MMC support for H6 mmc: sunxi: Add DM_MMC support for A80 arm: sunxi: Enable DM_MMC arm: dts: sunxi: Enumerate MMC2 as MMC1 arch/arm/Kconfig | 1 + arch/arm/dts/sunxi-u-boot.dtsi | 4 + .../include/asm/arch-sunxi/clock_sun50i_h6.h | 3 + arch/arm/mach-sunxi/Kconfig | 1 - configs/Linksprite_pcDuino3_defconfig | 1 - drivers/mmc/sunxi_mmc.c | 73 ++++++++++++++++++- 6 files changed, 79 insertions(+), 4 deletions(-) -- 2.18.0.321.gffc6fa0e3

4 14

[U-Boot] (no subject)
by Angelo Dureghello 19 Jan '19

19 Jan '19

[PATCH RESEND] drivers: esdhc: add support for ColdFire mcf5441x family

1 0

[U-Boot] [PATCH] arm: dts: am335x-pdu001: Sync with Linux 5.0-rc2
by Felix Brack 19 Jan '19

19 Jan '19

This patch synchronizes the PDU001 board DTS file with the one used by Linux 5.0-rc2. Signed-off-by: Felix Brack <fb(a)ltec.ch> --- arch/arm/dts/am335x-pdu001.dts | 25 +++++++++++++++++-------- 1 file changed, 17 insertions(+), 8 deletions(-) diff --git a/arch/arm/dts/am335x-pdu001.dts b/arch/arm/dts/am335x-pdu001.dts index 3a5e952663..ae43d61f4e 100644 --- a/arch/arm/dts/am335x-pdu001.dts +++ b/arch/arm/dts/am335x-pdu001.dts @@ -1,4 +1,3 @@ -// SPDX-License-Identifier: GPL-2.0+ /* * pdu001.dts * @@ -7,6 +6,8 @@ * Copyright (C) 2018 EETS GmbH - http://www.eets.ch/ * * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/ + * + * SPDX-License-Identifier: GPL-2.0+ */ /dts-v1/; @@ -17,7 +18,7 @@ / { model = "EETS,PDU001"; - compatible = "eets,pdu001", "ti,am33xx"; + compatible = "ti,am33xx"; chosen { stdout-path = &uart3; @@ -303,12 +304,12 @@ clock-frequency = <100000>; board_24aa025e48: board_24aa025e48@50 { - compatible = "microchip,24aa025e48"; + compatible = "atmel,24c02"; reg = <0x50>; }; backplane_24aa025e48: backplane_24aa025e48@53 { - compatible = "microchip,24aa025e48"; + compatible = "atmel,24c02"; reg = <0x53>; }; @@ -372,8 +373,8 @@ ti,pindir-d0-out-d1-in; status = "okay"; - cfaf240320a032t { - compatible = "orise,otm3225a"; + display-controller@0 { + compatible = "orisetech,otm3225a"; reg = <0>; spi-max-frequency = <1000000>; // SPI mode 3 @@ -532,16 +533,24 @@ pinctrl-names = "default"; pinctrl-0 = <&davinci_mdio_default>; status = "okay"; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; + + ethphy1: ethernet-phy@1 { + reg = <1>; + }; }; &cpsw_emac0 { - phy_id = <&davinci_mdio>, <0>; + phy-handle = <&ethphy0>; phy-mode = "mii"; dual_emac_res_vlan = <1>; }; &cpsw_emac1 { - phy_id = <&davinci_mdio>, <1>; + phy-handle = <&ethphy1>; phy-mode = "mii"; dual_emac_res_vlan = <2>; }; -- 2.17.1

2 1

[U-Boot] [PATCH] configs: Remove am335x_boneblack_defconfig
by Faiz Abbas 19 Jan '19

19 Jan '19

The am335x_evm_defconfig supports all am335x_boneblack variants. Remove the redundant am335x_boneblack_defconfig. Signed-off-by: Faiz Abbas <faiz_abbas(a)ti.com> --- configs/am335x_boneblack_defconfig | 50 ------------------------------ 1 file changed, 50 deletions(-) delete mode 100644 configs/am335x_boneblack_defconfig diff --git a/configs/am335x_boneblack_defconfig b/configs/am335x_boneblack_defconfig deleted file mode 100644 index 439d0cba05..0000000000 --- a/configs/am335x_boneblack_defconfig +++ /dev/null @@ -1,50 +0,0 @@ -CONFIG_ARM=y -CONFIG_ARCH_OMAP2PLUS=y -CONFIG_TI_COMMON_CMD_OPTIONS=y -CONFIG_AM33XX=y -CONFIG_SPL=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_SYS_EXTRA_OPTIONS="EMMC_BOOT" -CONFIG_BOOTCOMMAND="if test ${boot_fit} -eq 1; then run update_to_fit; fi; run findfdt; run init_console; run envboot; run distro_bootcmd" -CONFIG_SYS_CONSOLE_INFO_QUIET=y -CONFIG_VERSION_VARIABLE=y -CONFIG_ARCH_MISC_INIT=y -CONFIG_SPL_MUSB_NEW_SUPPORT=y -# CONFIG_SPL_NAND_SUPPORT is not set -CONFIG_SPL_OS_BOOT=y -CONFIG_AUTOBOOT_KEYED=y -CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" -CONFIG_AUTOBOOT_DELAY_STR="d" -CONFIG_AUTOBOOT_STOP_STR=" " -CONFIG_CMD_SPL=y -# CONFIG_CMD_FLASH is not set -# CONFIG_CMD_SETEXPR is not set -CONFIG_ENV_IS_IN_MMC=y -CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y -CONFIG_BOOTCOUNT_LIMIT=y -CONFIG_DFU_TFTP=y -CONFIG_DFU_MMC=y -CONFIG_DFU_RAM=y -CONFIG_USB_FUNCTION_FASTBOOT=y -CONFIG_FASTBOOT_FLASH=y -CONFIG_FASTBOOT_FLASH_MMC_DEV=1 -CONFIG_FASTBOOT_CMD_OEM_FORMAT=y -CONFIG_MMC_OMAP_HS=y -CONFIG_SPI_FLASH=y -CONFIG_SPI_FLASH_WINBOND=y -CONFIG_MII=y -CONFIG_DRIVER_TI_CPSW=y -CONFIG_SPI=y -CONFIG_OMAP3_SPI=y -CONFIG_USB=y -CONFIG_USB_MUSB_HOST=y -CONFIG_USB_MUSB_GADGET=y -CONFIG_USB_MUSB_DSPS=y -CONFIG_USB_GADGET=y -CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" -CONFIG_USB_GADGET_VENDOR_NUM=0x0451 -CONFIG_USB_GADGET_PRODUCT_NUM=0xd022 -CONFIG_USB_ETHER=y -CONFIG_USBNET_HOST_ADDR="de:ad:be:af:00:00" -CONFIG_LZO=y -CONFIG_OF_LIBFDT=y -- 2.19.2

2 2

[U-Boot] [PATCH] arm: am335x-pdu001: Remove SPI support
by Felix Brack 19 Jan '19

19 Jan '19

On this board SPI is only used to configure the SoC driving the LC TFT display which is not used in U-Boot. Hence remove SPI support. Signed-off-by: Felix Brack <fb(a)ltec.ch> --- configs/am335x_pdu001_defconfig | 1 - 1 file changed, 1 deletion(-) diff --git a/configs/am335x_pdu001_defconfig b/configs/am335x_pdu001_defconfig index e93c411766..2a8d318e57 100644 --- a/configs/am335x_pdu001_defconfig +++ b/configs/am335x_pdu001_defconfig @@ -50,6 +50,5 @@ CONFIG_SPL_DM_REGULATOR=y CONFIG_DM_REGULATOR_FIXED=y CONFIG_DM_REGULATOR_TPS65910=y CONFIG_CONS_INDEX=4 -CONFIG_SPI=y # CONFIG_USE_TINY_PRINTF is not set # CONFIG_EFI_LOADER is not set -- 2.17.1

2 1

[U-Boot] [PATCH] cmd: mtd: fix compilation warning for help when SYS_LONGHELP=n
by Quentin Schulz 19 Jan '19

19 Jan '19

cmd/mtd.c:447:13: warning: ‘mtd_help_text’ defined but not used [-Wunused-variable] static char mtd_help_text[] = ^~~~~~~~~~~~~ When SYS_LONGHELP is not defined. After looking at how other commands work, we should surround the whole help text (even its declaration) with an #ifdef CONFIG_SYS_LONGHELP, since it's compiled out when calling _CMD_HELP[1] on the help text variable argument to U_BOOT_CMD. [1] https://elixir.bootlin.com/u-boot/latest/source/include/command.h#L181 Signed-off-by: Quentin Schulz <quentin.schulz(a)bootlin.com> --- cmd/mtd.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) diff --git a/cmd/mtd.c b/cmd/mtd.c index 6142223984..361813a4a1 100644 --- a/cmd/mtd.c +++ b/cmd/mtd.c @@ -444,8 +444,8 @@ static int do_mtd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) return CMD_RET_SUCCESS; } -static char mtd_help_text[] = #ifdef CONFIG_SYS_LONGHELP +static char mtd_help_text[] = "- generic operations on memory technology devices\n\n" "mtd list\n" "mtd read[.raw][.oob] <name> <addr> [<off> [<size>]]\n" @@ -466,8 +466,7 @@ static char mtd_help_text[] = "\t\t* must be a multiple of a block for erase\n" "\t\t* must be a multiple of a page otherwise (special case: default is a page with dump)\n" "\n" - "The .dontskipff option forces writing empty pages, don't use it if unsure.\n" + "The .dontskipff option forces writing empty pages, don't use it if unsure.\n"; #endif - ""; U_BOOT_CMD(mtd, 10, 1, do_mtd, "MTD utils", mtd_help_text); -- 2.17.1

3 2

[U-Boot] [PATCH v2 1/2] travis: Setup QEMU_VERSION as variable
by Michal Simek 19 Jan '19

19 Jan '19

This change enables setting up specific Qemu version or sha1 for new targets which are added after (current) v3.0.0 version. This changes is preparation step for adding new Xilinx Versal Virt platform which was merge after v3.0.0. Signed-off-by: Michal Simek <michal.simek(a)xilinx.com> Reviewed-by: Bin Meng <bmeng.cn(a)gmail.com> --- Changes in v2: None .travis.yml | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/.travis.yml b/.travis.yml index 321fd793a756..6e4b4ba0a34a 100644 --- a/.travis.yml +++ b/.travis.yml @@ -63,6 +63,7 @@ env: - BUILD_DIR=build - HOSTCC="cc" - HOSTCXX="c++" + - QEMU_VERSION="v3.0.0" before_script: # install toolchains based on TOOLCHAIN} variable @@ -97,7 +98,7 @@ before_script: git clone git://git.qemu.org/qemu.git /tmp/qemu; pushd /tmp/qemu; git submodule update --init dtc && - git checkout v3.0.0 && + git checkout ${QEMU_VERSION} && ./configure --prefix=/tmp/qemu-install --target-list=${QEMU_TARGET} && make -j4 all install; popd; -- 1.9.1

2 5