May 2017 - U-Boot

[U-Boot] [PATCH 0/5] dm: led: add BCM6328 led support
by Álvaro Fernández Rojas 10 May '17

10 May '17

BCM6328 supports controlling LEDs both by using the GPIO controller and the LED controller. However, LED controller allows HW blinking and supports serial LEDs. Álvaro Fernández Rojas (5): dm: led: add BCM6328 led driver mips: bmips: add bcm6328-led driver support for BCM6328 mips: bmips: add bcm6328-led driver support for BCM63268 mips: bmips: add Comtrend AR-5387un bcm6328-leds mips: bmips: add Comtrend VR-3032u bcm6328-leds arch/mips/dts/brcm,bcm63268.dtsi | 9 ++ arch/mips/dts/brcm,bcm6328.dtsi | 9 ++ arch/mips/dts/comtrend,ar-5387un.dts | 30 ++++ arch/mips/dts/comtrend,vr-3032u.dts | 43 ++++++ configs/comtrend_ar5387un_ram_defconfig | 4 + configs/comtrend_vr3032u_ram_defconfig | 4 + drivers/led/Kconfig | 7 + drivers/led/Makefile | 1 + drivers/led/led_bcm6328.c | 262 ++++++++++++++++++++++++++++++++ 9 files changed, 369 insertions(+) create mode 100644 drivers/led/led_bcm6328.c -- 2.1.4

3 17

[U-Boot] [PATCH 0/5] dm: gpio: add BMIPS gpio support
by Álvaro Fernández Rojas 10 May '17

10 May '17

Broadcom MIPS SoCs have one or two GPIO banks, depending on the number of gpios present: BCM6345 => 16 GPIOs / 1 bank BCM6328 => 32 GPIOs / 1 bank BCM6358 => 40 GPIOs / 2 banks BCM63268 => 52 GPIOs / 2 banks typedef struct GpioControl { uint32 GPIODirHi; /* 0 */ uint32 GPIODir; /* 4 */ uint32 GPIOioHi; /* 8 */ uint32 GPIOio; /* C */ } Álvaro Fernández Rojas (5): dm: gpio: add BCM6345 gpio driver mips: bmips: add bcm6345-gpio driver support for BCM6358 mips: bmips: add bcm6345-gpio driver support for BCM6328 mips: bmips: add bcm6345-gpio driver support for BCM63268 mips: bmips: add Huawei HG556a gpio-leds arch/mips/dts/brcm,bcm63268.dtsi | 19 ++++++ arch/mips/dts/brcm,bcm6328.dtsi | 9 +++ arch/mips/dts/brcm,bcm6358.dtsi | 19 ++++++ arch/mips/dts/huawei,hg556a.dts | 73 +++++++++++++++++++++ configs/huawei_hg556a_ram_defconfig | 4 ++ drivers/gpio/Kconfig | 6 ++ drivers/gpio/Makefile | 1 + drivers/gpio/bcm6345_gpio.c | 125 ++++++++++++++++++++++++++++++++++++ 8 files changed, 256 insertions(+) create mode 100644 drivers/gpio/bcm6345_gpio.c -- 2.1.4

3 17

[U-Boot] [PATCH 0/5] dm: rst: add BCM6345 reset controller support
by Álvaro Fernández Rojas 10 May '17

10 May '17

Broadcom MIPS SoCs have reset controllers which supports asserting and deasserting each peripheral controller. Checking reset status is not supported, which is why delays are used. Álvaro Fernández Rojas (5): dm: reset: add BCM6345 reset driver mips: bmips: add bcm6345-rst driver support for BCM6358 mips: bmips: add bcm6345-rst driver support for BCM6328 mips: bmips: add bcm6345-rst driver support for BCM63268 mips: bmips: enable bcm6345-reset driver for all BMIPS boards arch/mips/dts/brcm,bcm63268.dtsi | 7 +++ arch/mips/dts/brcm,bcm6328.dtsi | 7 +++ arch/mips/dts/brcm,bcm6358.dtsi | 7 +++ configs/comtrend_ar5387un_ram_defconfig | 3 + configs/comtrend_vr3032u_ram_defconfig | 3 + configs/huawei_hg556a_ram_defconfig | 3 + configs/sfr_nb4-ser_ram_defconfig | 3 + drivers/reset/Kconfig | 6 ++ drivers/reset/Makefile | 1 + drivers/reset/reset-bcm6345.c | 89 ++++++++++++++++++++++++++++++ include/dt-bindings/reset/bcm63268-reset.h | 32 +++++++++++ include/dt-bindings/reset/bcm6328-reset.h | 24 ++++++++ include/dt-bindings/reset/bcm6358-reset.h | 21 +++++++ 13 files changed, 206 insertions(+) create mode 100644 drivers/reset/reset-bcm6345.c create mode 100644 include/dt-bindings/reset/bcm63268-reset.h create mode 100644 include/dt-bindings/reset/bcm6328-reset.h create mode 100644 include/dt-bindings/reset/bcm6358-reset.h -- 2.1.4

3 11

[U-Boot] NS16550 Baud Rates on OMAP3
by Adam Ford 10 May '17

10 May '17

Does anyone have any experience running the baud rate with the NS16550 serial driver at high rates (like 921600) I know someone who is having success with this rate in Linux but not U-Boot (from 2011). It looks like the calc_divisor was changed to use DIV_ROUND_CLOSEST a while ago, but the comments indicate it will return the same value. adam

1 0

[U-Boot] [PATCH v2 0/2] This series introduces the ability to override the environment offets
by Philipp Tomsich 10 May '17

10 May '17

from the device tree by setting the following nodes in '/config': 'u-boot,mmc-env-offset' - overrides CONFIG_ENV_OFFSET 'u-boot,mmc-env-offset-redundant' - overrides CONFIG_ENV_OFFSET_REDUND and adds the appropriate documentation in config.txt. Changes in v2: - added documentation in config.txt Philipp Tomsich (2): env_mmc: configure environment offsets via device tree doc: document u-boot,mmc-env-offset and u-boot,mmc-env-offset-redund common/env_mmc.c | 31 +++++++++++++++++++++++++++---- doc/device-tree-bindings/config.txt | 12 ++++++++++++ 2 files changed, 39 insertions(+), 4 deletions(-) -- 1.9.1

3 4

[U-Boot] [PATCH] davinci: omapl138_lcdk: enable time command
by Sekhar Nori 10 May '17

10 May '17

Enable time command for OMAP-L138 LCDK board. The patch was generated using savedefconfig method. Signed-off-by: Sekhar Nori <nsekhar(a)ti.com> --- configs/omapl138_lcdk_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/configs/omapl138_lcdk_defconfig b/configs/omapl138_lcdk_defconfig index 7a5a78f4944b..d6de9b82787e 100644 --- a/configs/omapl138_lcdk_defconfig +++ b/configs/omapl138_lcdk_defconfig @@ -25,6 +25,7 @@ CONFIG_CMD_PART=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y +CONFIG_CMD_TIME=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y -- 2.9.0

3 5

[U-Boot] USB2.0 device timeout issue.
by Terry Zhou 10 May '17

10 May '17

Hi all, This is Terry from Marvell BSP team in ShangHai China. We got one issue in USB like below: 1) When reading large files(larger than 32M ) from USB2.0 u-disk, two of the disks got the timeout error like below: Marvell>> fatload usb 0:1 0x1000000 got.mkv 0x2000000 reading got.mkv EHCI timed out on TD - token=0x1e008d80 EHCI timed out on TD - token=0x1e008d80 EHCI timed out on TD - token=0x1e008d80 Error reading cluster ** Unable to read file got.mkv ** 2) I did some research on this issue and found that this issue disappear if we set "USB_MAX_XFER_BLK" to a smaller value. /common/usb_storage.c @@ -145,7 +145,7 @@ struct us_data { * limited to 65535 blocks. */ #elif defined(CONFIG_USB_EHCI) -#define USB_MAX_XFER_BLK 65535 +#define USB_MAX_XFER_BLK 8000 3) We also did some test in linux, it works in linux, we found that linux set the max_sectors to 240, and even we set them to a larger value, The maximum value is 512, which is safe compares to the 8000 in Uboot. Reference link for linux: http://www.linux-usb.org/FAQ.html#i5 4) I found in Uboot forum, other guys met the same problem with us, see the link below: https://lists.denx.de/pipermail/u-boot/2016-February/246405.html and there is also some patches to find the optimal value of USB_MAX_XFER_BLK https://www.mail-archive.com/u-boot@lists.denx.de/msg215952.html But these patches have not been pushed to the mainline code. Could you please share your ideas, why we didn't merge the patches and how should we fix this issue? Thanks. Best Regards, Terry

1 0

[U-Boot] Marvell Kirkwood Guruplug Server Standard upgrade uboot and standalone app issue
by Kernel Hacker 10 May '17

10 May '17

I have a Guruplug server standard that I would like to upgrade with a newer version of u-boot. Serial output during boot currently shows the following: ----------------cut---------------- U-Boot 2009.11-rc1-00602-g8e6db3d (Dec 24 2009 - 03:11:17) Marvell-Plug2 SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB In: serial Out: serial Err: serial Net: egiga0 88E1121 Initialized on egiga0 Hit any key to stop autoboot: 0 Marvell>> ----------------cut---------------- I cloned git://git.denx.de/u-boot-marvell.git and built u-boot off master branch: make mrproper make guruplug_config make CROSS_COMPILE=arm-none-eabi- u-boot.kwb I wanted to verify that my uboot works properly on my device before committing to flash since I don't have a JTAG available at the moment. However, when I tftp the new u-boot.bin image to the device and issue a "go 0x......" command it never starts (no output after "Starting application at ...". Also, to do a sanity check I tried to get the standalone hello_world.bin to run in the current u-boot and I am unable to get this to work. I loaded the hellow_world.bin to 0x0c100000 (tftp 0x0c100000 hello_world.bin" and then I issue "go 0x0c100000" and again nothing is printed after the "Starting application at ..." is printed by u-boot. So my questions are what am I doing wrong and am I using the right repo, branch, and configuration? Appreciate any pointers.

2 3

[U-Boot] Please pull u-boot-dm
by Simon Glass 10 May '17

10 May '17

Hi Tom, This was my dm/next branch - it includes generic PHY uclass, some SCSI changes and a lot of AT91 driver-mode conversions. The following changes since commit 85ea850976daea57c8045f3569566fad5ce9fe0f: p1_p2_rdb: Fix unused variable warning (2017-05-09 09:11:04 -0400) are available in the git repository at: git://git.denx.de/u-boot-dm.git for you to fetch changes up to 9d0c4decfeaa7e312f50e0debb677f60ad170f61: defconfig: dra7xx_evm: enable CONFIG_BLK and disk driver model for SCSI (2017-05-09 12:14:16 -0600) ---------------------------------------------------------------- Jean-Jacques Hiblot (7): scsi: dm: split scsi_scan() drivers: phy: add generic PHY framework dm: test: Add tests for the generic PHY uclass drivers: phy: add PIPE3 phy driver dra7: dtsi: mark ocp2scp bus compatible with "simple-bus" drivers: block: dwc_ahci: Implement a driver for Synopsys DWC sata device defconfig: dra7xx_evm: enable CONFIG_BLK and disk driver model for SCSI Wenyou Yang (40): ARM: dts: sama5d2: add clock property for uart1 node ARM: dts: sama5d2_xplained: update for SPL configs: sama5d2_xplained: enable CONFIG_DM_ETH board: sama5d2_xplained: clean up macb init code board: sama5d2_xplained: remove uart1 init board: sama5d2_xplained: remove unnecessary header files configs: sama5d2_xplained: update for SPL board: sama5d4ek: fix DD2 configuration configs: sama5d3xek: add default config for CMP board net: macb: Add remove callback net: macb: Align the compatibles with kernel clk: at91: Enhance the peripheral clock clk: at91: Align clk-master compatibles with kernel clk: at91: Align the at91 pmc's compatibles serial: atmel_usart: Fix early debug not work in SPL serial: atmel_usart: Add clk support ARM: dts: at91: Add dts files for at91sam9x5ek ARM: dts: at91: Add dts files for at91sam9n12ek ARM: dts: at91: Add dts files for at91sam9m10g45ek ARM: dts: at91: Add dts files for at91sam9260ek/9g20ek ARM: dts: at91: Add dts files for at91sam9rlek ARM: dts: at91: Add dts files for at91sam9263ek configs: at91sam9x5ek: Update to support DM/DT board: at91sam9x5ek: Clean up code board: at91sam9x5ek: Enable early debug UART configs: at91sam9n12ek: Update for DT and DM support board: at91sam9n12ek: Clean up code board: at91sam9n12ek: Enable early debug UART configs: at91sam9m10g45ek: Update to support DM/DT board: at91sam9m10g45ek: Clean up code board: at91sam9m10g45ek: Enable early debug UART configs: at91sam9260ek/9g20ek: Update for DT and DM board: at91sam9260ek: Clean up code board: at91sam9260ek/9g20ek: Enable early debug UART configs: at91sam9rlek: Update for DT and DM support board: at91sam9rlek: Clean up code board: at91sam9rlek: Enable early debug UART configs: at91sam9263ek: Update for DT and DM support board: at91sam9263ek: Clean up code board: at91sam9263ek: Enable early debug UART arch/arm/dts/Makefile | 20 ++ arch/arm/dts/at91-sama5d2_xplained.dts | 12 + arch/arm/dts/at91sam9260.dtsi | 149 ++++---- arch/arm/dts/at91sam9260ek.dts | 215 +++++++++++ arch/arm/dts/at91sam9263.dtsi | 198 ++++++----- arch/arm/dts/at91sam9263ek.dts | 229 ++++++++++++ arch/arm/dts/at91sam9g15.dtsi | 29 ++ arch/arm/dts/at91sam9g15ek.dts | 26 ++ arch/arm/dts/at91sam9g20.dtsi | 4 +- arch/arm/dts/at91sam9g20ek.dts | 29 ++ arch/arm/dts/at91sam9g20ek_2mmc.dts | 56 +++ arch/arm/dts/at91sam9g20ek_common.dtsi | 227 ++++++++++++ arch/arm/dts/at91sam9g25.dtsi | 31 ++ arch/arm/dts/at91sam9g25ek.dts | 69 ++++ arch/arm/dts/at91sam9g35.dtsi | 30 ++ arch/arm/dts/at91sam9g35ek.dts | 31 ++ arch/arm/dts/at91sam9g45.dtsi | 218 ++++++------ arch/arm/dts/at91sam9m10g45ek.dts | 359 +++++++++++++++++++ arch/arm/dts/at91sam9n12.dtsi | 1064 ++++++++++++++++++++++++++++++++++++++++++++++++++++++ arch/arm/dts/at91sam9n12ek.dts | 265 ++++++++++++++ arch/arm/dts/at91sam9rl.dtsi | 1139 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ arch/arm/dts/at91sam9rlek.dts | 239 +++++++++++++ arch/arm/dts/at91sam9x25.dtsi | 32 ++ arch/arm/dts/at91sam9x25ek.dts | 30 ++ arch/arm/dts/at91sam9x35.dtsi | 31 ++ arch/arm/dts/at91sam9x35ek.dts | 30 ++ arch/arm/dts/at91sam9x5.dtsi | 1302 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ arch/arm/dts/at91sam9x5_can.dtsi | 71 ++++ arch/arm/dts/at91sam9x5_isi.dtsi | 72 ++++ arch/arm/dts/at91sam9x5_lcd.dtsi | 146 ++++++++ arch/arm/dts/at91sam9x5_macb0.dtsi | 67 ++++ arch/arm/dts/at91sam9x5_macb1.dtsi | 55 +++ arch/arm/dts/at91sam9x5_usart3.dtsi | 69 ++++ arch/arm/dts/at91sam9x5cm.dtsi | 100 ++++++ arch/arm/dts/at91sam9x5dm.dtsi | 66 ++++ arch/arm/dts/at91sam9x5ek.dtsi | 167 +++++++++ arch/arm/dts/omap5-u-boot.dtsi | 4 + arch/arm/dts/sama5d2.dtsi | 22 ++ arch/arm/mach-at91/include/mach/atmel_mpddrc.h | 7 +- arch/sandbox/dts/test.dts | 17 + board/atmel/at91sam9260ek/Makefile | 2 +- board/atmel/at91sam9260ek/at91sam9260ek.c | 79 +---- board/atmel/at91sam9263ek/Makefile | 2 +- board/atmel/at91sam9263ek/at91sam9263ek.c | 64 +--- board/atmel/at91sam9m10g45ek/Makefile | 2 +- board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 107 +----- board/atmel/at91sam9n12ek/at91sam9n12ek.c | 64 +--- board/atmel/at91sam9rlek/Makefile | 2 +- board/atmel/at91sam9rlek/at91sam9rlek.c | 24 +- board/atmel/at91sam9x5ek/at91sam9x5ek.c | 82 +---- board/atmel/sama5d2_xplained/sama5d2_xplained.c | 49 +-- board/atmel/sama5d4ek/sama5d4ek.c | 16 +- common/scsi.c | 102 +++--- configs/at91sam9260ek_dataflash_cs0_defconfig | 21 +- configs/at91sam9260ek_dataflash_cs1_defconfig | 21 +- configs/at91sam9260ek_nandflash_defconfig | 21 +- configs/at91sam9263ek_dataflash_cs0_defconfig | 24 +- configs/at91sam9263ek_dataflash_defconfig | 24 +- configs/at91sam9263ek_nandflash_defconfig | 24 +- configs/at91sam9263ek_norflash_boot_defconfig | 24 +- configs/at91sam9263ek_norflash_defconfig | 24 +- configs/at91sam9g20ek_2mmc_defconfig | 24 +- configs/at91sam9g20ek_2mmc_nandflash_defconfig | 24 +- configs/at91sam9g20ek_dataflash_cs0_defconfig | 21 +- configs/at91sam9g20ek_dataflash_cs1_defconfig | 21 +- configs/at91sam9g20ek_nandflash_defconfig | 21 +- configs/at91sam9m10g45ek_mmc_defconfig | 34 +- configs/at91sam9m10g45ek_nandflash_defconfig | 32 +- configs/at91sam9n12ek_mmc_defconfig | 25 +- configs/at91sam9n12ek_nandflash_defconfig | 31 +- configs/at91sam9n12ek_spiflash_defconfig | 32 +- configs/at91sam9rlek_dataflash_defconfig | 22 +- configs/at91sam9rlek_mmc_defconfig | 22 +- configs/at91sam9rlek_nandflash_defconfig | 22 +- configs/at91sam9x5ek_dataflash_defconfig | 29 +- configs/at91sam9x5ek_mmc_defconfig | 29 +- configs/at91sam9x5ek_nandflash_defconfig | 35 +- configs/at91sam9x5ek_spiflash_defconfig | 36 +- configs/at91sam9xeek_dataflash_cs0_defconfig | 21 +- configs/at91sam9xeek_dataflash_cs1_defconfig | 21 +- configs/at91sam9xeek_nandflash_defconfig | 21 +- configs/dra7xx_evm_defconfig | 12 +- configs/dra7xx_hs_evm_defconfig | 11 +- configs/sama5d2_xplained_mmc_defconfig | 10 +- configs/sama5d2_xplained_spiflash_defconfig | 9 +- configs/sama5d36ek_cmp_mmc_defconfig | 51 +++ configs/sama5d36ek_cmp_nandflash_defconfig | 51 +++ configs/sama5d36ek_cmp_spiflash_defconfig | 51 +++ configs/sandbox_defconfig | 2 + configs/sandbox_noblk_defconfig | 2 + configs/sandbox_spl_defconfig | 2 + drivers/Kconfig | 2 + drivers/Makefile | 1 + drivers/block/Kconfig | 10 + drivers/block/Makefile | 1 + drivers/block/dwc_ahci.c | 101 ++++++ drivers/clk/at91/clk-master.c | 1 + drivers/clk/at91/clk-peripheral.c | 29 +- drivers/clk/at91/pmc.c | 6 + drivers/net/macb.c | 52 ++- drivers/phy/Kconfig | 62 ++++ drivers/phy/Makefile | 10 + drivers/phy/phy-uclass.c | 139 ++++++++ drivers/phy/sandbox-phy.c | 108 ++++++ drivers/phy/ti-pipe3-phy.c | 373 +++++++++++++++++++ drivers/serial/atmel_usart.c | 84 ++++- include/configs/at91sam9260ek.h | 31 +- include/configs/at91sam9263ek.h | 26 +- include/configs/at91sam9m10g45ek.h | 31 +- include/configs/at91sam9n12ek.h | 21 +- include/configs/at91sam9rlek.h | 24 +- include/configs/at91sam9x5ek.h | 27 +- include/configs/sama5d2_xplained.h | 19 +- include/dm/uclass-id.h | 1 + include/generic-phy.h | 224 ++++++++++++ test/dm/Makefile | 1 + test/dm/phy.c | 112 ++++++ 117 files changed, 8935 insertions(+), 990 deletions(-) create mode 100644 arch/arm/dts/at91sam9260ek.dts create mode 100644 arch/arm/dts/at91sam9263ek.dts create mode 100644 arch/arm/dts/at91sam9g15.dtsi create mode 100644 arch/arm/dts/at91sam9g15ek.dts create mode 100644 arch/arm/dts/at91sam9g20ek.dts create mode 100644 arch/arm/dts/at91sam9g20ek_2mmc.dts create mode 100644 arch/arm/dts/at91sam9g20ek_common.dtsi create mode 100644 arch/arm/dts/at91sam9g25.dtsi create mode 100644 arch/arm/dts/at91sam9g25ek.dts create mode 100644 arch/arm/dts/at91sam9g35.dtsi create mode 100644 arch/arm/dts/at91sam9g35ek.dts create mode 100644 arch/arm/dts/at91sam9m10g45ek.dts create mode 100644 arch/arm/dts/at91sam9n12.dtsi create mode 100644 arch/arm/dts/at91sam9n12ek.dts create mode 100644 arch/arm/dts/at91sam9rl.dtsi create mode 100644 arch/arm/dts/at91sam9rlek.dts create mode 100644 arch/arm/dts/at91sam9x25.dtsi create mode 100644 arch/arm/dts/at91sam9x25ek.dts create mode 100644 arch/arm/dts/at91sam9x35.dtsi create mode 100644 arch/arm/dts/at91sam9x35ek.dts create mode 100644 arch/arm/dts/at91sam9x5.dtsi create mode 100644 arch/arm/dts/at91sam9x5_can.dtsi create mode 100644 arch/arm/dts/at91sam9x5_isi.dtsi create mode 100644 arch/arm/dts/at91sam9x5_lcd.dtsi create mode 100644 arch/arm/dts/at91sam9x5_macb0.dtsi create mode 100644 arch/arm/dts/at91sam9x5_macb1.dtsi create mode 100644 arch/arm/dts/at91sam9x5_usart3.dtsi create mode 100644 arch/arm/dts/at91sam9x5cm.dtsi create mode 100644 arch/arm/dts/at91sam9x5dm.dtsi create mode 100644 arch/arm/dts/at91sam9x5ek.dtsi create mode 100644 configs/sama5d36ek_cmp_mmc_defconfig create mode 100644 configs/sama5d36ek_cmp_nandflash_defconfig create mode 100644 configs/sama5d36ek_cmp_spiflash_defconfig create mode 100644 drivers/block/dwc_ahci.c create mode 100644 drivers/phy/Kconfig create mode 100644 drivers/phy/Makefile create mode 100644 drivers/phy/phy-uclass.c create mode 100644 drivers/phy/sandbox-phy.c create mode 100644 drivers/phy/ti-pipe3-phy.c create mode 100644 include/generic-phy.h create mode 100644 test/dm/phy.c Regards, Simon

2 1

[U-Boot] Please pull u-boot-marvell/master
by Stefan Roese 10 May '17

10 May '17

Hi Tom, please pull the first batch of Marvell related patches in this merge window. Thanks, Stefan The following changes since commit 2f92629112a1055ed37f8b05dfcf00c3f1875503: Merge branch 'next' of git://git.denx.de/u-boot-spi (2017-05-08 15:44:52 -0400) are available in the git repository at: git://www.denx.de/git/u-boot-marvell.git for you to fetch changes up to e38f5fc8d80d946b401ba0e9ba0fcb52d6e7e74b: ARM: mvebu: switch db-88f6820-amc to DM for i2c (2017-05-09 13:38:18 +0200) ---------------------------------------------------------------- Chris Packham (1): ARM: mvebu: switch db-88f6820-amc to DM for i2c Igal Liberman (5): fix: phy: marvell: cp110: sata: update analog parameters according to latest ETP phy: marvell: cp110: add 5G XFI mode fix: phy: marvell: cp110: sfi: update analog parameters according to latest ETP fix: phy: marvell: cp110: rename comphy_index to cp_index fix: phy: marvell: cp110: pcie: update analog parameters according to latest ETP Konstantin Porotchkin (9): fix: mvebu: pcie_dw: Allow probing empty PCIe slots mvebu: dts: a80x0: Sync the DB DTS with standard config A arm64: mvebu: Trigger PCI devices scan at early init stage arm64: mvebu: a8k: Add support for NAND clock get arm64: a8k: dts: Add support for NAND devices on A8K platform arm64: mvebu: a8k: Add NAND configuration parameters fix: mvebu_ comphy: Update COMPHY sequence number fix: nand: pxa3xx: Remove hardcode values from the driver arm64: mvebu: Fix the bubt comamnd NAND device support Stefan Roese (9): net: mvpp2: Add remove function that is called before the OS is started phy: marvell: Replace PHY_TYPE_KR with PHY_TYPE_SFI phy: marvell: cp110: add support for end point configuration phy: marvell: cp110: update utmi phy connection type phy: marvell: add IGNORE COMPHY type fix: phy: marvell: cp110: fix the KR/SFI line 4 selector fix: phy: marvell: cp110: update comphy selector option fix: phy: marvell: cp110: fix comphy lane 4 selection options phy: marvell: print comphy status even when it's disconnected Uwe Kleine-König (1): arm: mvebu: Minor fixes in the AXP / A38x SERDES code arch/arm/dts/Makefile | 1 + arch/arm/dts/armada-385-amc.dts | 3 + arch/arm/dts/armada-7040-db-nand.dts | 223 ++++++++++ arch/arm/dts/armada-7040-db.dts | 3 +- arch/arm/dts/armada-8040-db.dts | 222 +++++----- arch/arm/dts/armada-8040-mcbin.dts | 14 +- arch/arm/dts/armada-cp110-master.dtsi | 18 +- arch/arm/dts/armada-cp110-slave.dtsi | 2 +- arch/arm/mach-mvebu/arm64-common.c | 6 + arch/arm/mach-mvebu/armada8k/cpu.c | 18 + .../serdes/a38x/high_speed_env_spec-38x.c | 2 - .../mach-mvebu/serdes/a38x/high_speed_env_spec.c | 4 +- .../arm/mach-mvebu/serdes/axp/high_speed_env_lib.c | 6 +- .../mach-mvebu/serdes/axp/high_speed_env_spec.c | 1 - cmd/mvebu/bubt.c | 13 +- configs/db-88f6820-amc_defconfig | 2 + configs/mvebu_db-88f7040-nand_defconfig | 72 ++++ drivers/mtd/nand/pxa3xx_nand.c | 62 ++- drivers/net/mvpp2.c | 24 ++ drivers/pci/pcie_dw_mvebu.c | 10 +- drivers/phy/marvell/comphy.h | 3 +- drivers/phy/marvell/comphy_core.c | 16 +- drivers/phy/marvell/comphy_cp110.c | 449 ++++++++++++++++++--- drivers/phy/marvell/comphy_hpipe.h | 277 ++++++++++++- drivers/phy/marvell/comphy_mux.c | 7 + include/configs/db-88f6820-amc.h | 7 - include/configs/mvebu_armada-8k.h | 11 + include/dt-bindings/comphy/comphy_data.h | 20 +- 28 files changed, 1247 insertions(+), 249 deletions(-) create mode 100644 arch/arm/dts/armada-7040-db-nand.dts create mode 100644 configs/mvebu_db-88f7040-nand_defconfig

2 1