September 2013 - U-Boot

[U-Boot] [PATCH 1/7] mtd: Fix function description in part_validate comment
by Otavio Salvador 29 Sep '13

29 Sep '13

The part_validate comment had a wrong description of the actions it does and referenced to non-existent functions while in fact it calls 'part_validate_eraseblock()'. Signed-off-by: Otavio Salvador <otavio(a)ossystems.com.br> --- common/cmd_mtdparts.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/common/cmd_mtdparts.c b/common/cmd_mtdparts.c index 3023479..0104285 100644 --- a/common/cmd_mtdparts.c +++ b/common/cmd_mtdparts.c @@ -381,10 +381,10 @@ static int part_validate_eraseblock(struct mtdids *id, struct part_info *part) /** - * Performs sanity check for supplied partition. Offset and size are verified - * to be within valid range. Partition type is checked and either - * parts_validate_nor() or parts_validate_nand() is called with the argument - * of part. + * Performs sanity check for supplied partition. Offset and size are + * verified to be within valid range. Partition type is checked and + * either part_validate_eraseblock() is called with the argument of + * part. * * @param id of the parent device * @param part partition to validate -- 1.8.4.rc3

4 15

[U-Boot] [RFC 0/3] ARM: cleanup gd init
by Jeroen Hofstee 28 Sep '13

28 Sep '13

Hello, As I noticed at [1] gd is setup multiple times. As pointed Tom pointed out out me this actually leads to problems as well, see [2]. These patches attempt to cleanup gd usage (a bit, board_f.c is not included since that one is rather trivial), some questions I have about it: 1) The major one, do these init changes brick any board? 2) Is there any board which needs gdata as a global? 3) What to do with lowlevel_init on armv7. Hide it under a CONFIG_*, make it weak.. or just remove it completely? 4) Keep the s_init in crt0.S or move it to the board_init_f? The disadvantage of the later is that all the different board_init_f's need to call system_init. 5) Where to put the __weak s_init (or hide this under a define) Regards, Jeroen [1] http://lists.denx.de/pipermail/u-boot/2013-August/160933.html [2] http://lists.denx.de/pipermail/u-boot/2013-July/158144.html Jeroen Hofstee (3): ARM,crt0.S: call s_init instead from ctr0.S ARM,crt0.S: optional init gd to gdata for spl ARM: do not assign gd outside of crt0.S arch/arm/cpu/arm926ejs/davinci/spl.c | 3 +-- arch/arm/cpu/armv7/exynos/spl_boot.c | 6 ++---- arch/arm/cpu/armv7/lowlevel_init.S | 23 +---------------------- arch/arm/cpu/armv7/omap-common/hwinit-common.c | 2 -- arch/arm/cpu/armv7/omap3/board.c | 2 -- arch/arm/cpu/armv7/omap3/lowlevel_init.S | 8 ++++---- arch/arm/cpu/armv7/rmobile/lowlevel_init.S | 6 ------ arch/arm/lib/crt0.S | 8 ++++++++ arch/arm/lib/reset.c | 5 +++++ arch/arm/lib/spl.c | 5 ++--- board/isee/igep0033/board.c | 1 - board/phytec/pcm051/board.c | 2 -- board/ti/am335x/board.c | 2 -- board/ti/omap5912osk/lowlevel_init.S | 11 ----------- board/ti/ti814x/evm.c | 2 -- board/woodburn/woodburn.c | 3 --- 16 files changed, 23 insertions(+), 66 deletions(-) -- 1.8.1.2

2 6

[U-Boot] [PATCH v2 1/6] mtd: Fix function description in part_validate comment
by Otavio Salvador 28 Sep '13

28 Sep '13

The part_validate comment had a wrong description of the actions it does and referenced to non-existent functions while in fact it calls 'part_validate_eraseblock()'. Signed-off-by: Otavio Salvador <otavio(a)ossystems.com.br> --- Changes in v2: - rework commit log (Eric Benard) common/cmd_mtdparts.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/common/cmd_mtdparts.c b/common/cmd_mtdparts.c index 3023479..0104285 100644 --- a/common/cmd_mtdparts.c +++ b/common/cmd_mtdparts.c @@ -381,10 +381,10 @@ static int part_validate_eraseblock(struct mtdids *id, struct part_info *part) /** - * Performs sanity check for supplied partition. Offset and size are verified - * to be within valid range. Partition type is checked and either - * parts_validate_nor() or parts_validate_nand() is called with the argument - * of part. + * Performs sanity check for supplied partition. Offset and size are + * verified to be within valid range. Partition type is checked and + * either part_validate_eraseblock() is called with the argument of + * part. * * @param id of the parent device * @param part partition to validate -- 1.8.4.rc3

1 5

[U-Boot] apparent(?) flaw in recent patch "am335x_evm: Switch to zImage as default rather
by Robert P. J. Day 28 Sep '13

28 Sep '13

than uImage" (i already tossed the original post so i can't reply to it directly, sorry.) this recent patch by tom rini to make zImage rather than uImage the default kernel format for am335x_evm: http://lists.denx.de/pipermail/u-boot/2013-September/163365.html seems flawed as the loading will work fine, but the boot will fail as the "bootm" command will still be used rather than "bootz". i just tested it building for my beaglebone black and that's exactly what happens: ... 3250520 bytes read in 552 ms (5.6 MiB/s) 24493 bytes read in 17 ms (1.4 MiB/s) Wrong Image Format for bootm command ERROR: can't get kernel image! ... so all i did as a quick hack was to add the (very specific for my test case) changes to replace "bootm" with "bootz" for only what i needed: @@ -105,21 +105,21 @@ "root=${ramroot} " \ "rootfstype=${ramrootfstype}\0" \ "loadramdisk=load mmc ${mmcdev} ${rdaddr} ramdisk.gz\0" \ - "loaduimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \ + "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \ "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \ "mmcloados=run mmcargs; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if run loadfdt; then " \ - "bootm ${loadaddr} - ${fdtaddr}; " \ + "bootz ${loadaddr} - ${fdtaddr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" \ "mmcboot=mmc dev ${mmcdev}; " \ "if mmc rescan; then " \ and the kernel boot worked fine. is this an actual flaw in the patch? or am i doing something silly? rday -- ======================================================================== Robert P. J. Day Ottawa, Ontario, CANADA http://crashcourse.ca Twitter: http://twitter.com/rpjday LinkedIn: http://ca.linkedin.com/in/rpjday ========================================================================

1 0

Re: [U-Boot] [PATCH 1/1] am33xx: add CONFIG_SYS_NAND_DEVICE_WIDTH to determine NAND device bus-width
by Gupta, Pekon 28 Sep '13

28 Sep '13

> From: Scott Wood [mailto:scottwood@freescale.com] > > On Fri, 2013-09-27 at 04:18 +0000, Gupta, Pekon wrote: > > > From: Scott Wood [mailto:scottwood@freescale.com] > > > > > > On Thu, 2013-09-26 at 13:14 +0000, Gupta, Pekon wrote: > > > > > > From: Gupta, Pekon <pekon(a)ti.com> > > > > > > [snip] > > The changelog that introduced am335x_spl_bch.c says that "custom > read_page implementation is required for proper syndrome generation." > Other than that ECC mode, AFAICT you're already using nand_spl_simple.c. > Oh I missed referring to nand_spl_simple.c. Thanks for pointing out. Yes, we already have a generic SPL driver. > > > > because SPL is mostly statically configured, and it just does plain NAND > read > > > > (it doesn’t even support NAND write, etc). > > > > But I do not know the hardware configurations tweaks of other SoC, > > > > So at-least have common CONFIG_SYS_NAND_xx which all SPL drivers > can > > > use. > > > > > > Again, are you introducing this symbol for use only in SPL? > > Apart from SPL, CONFIG_SYS_NAND_DEVICE_WIDTH also be useful for > > (1) drivers which do not use CONFIG_SYS_NAND_ONFI_DETECTION, where > > code for reading on-chip ONFI parameters is not enabled in nand_base.c > > (2) non ONFI compatible NAND devices. > > Unlikely, given that they've all managed to work without this so far. > E.g. eLBC and IFC hardcode this information on a per-chip basis in the > #defines that hold values for config registers, and prior to this patch > omap_gpmc had code to read a config register (regardless of where it > originally got set). > (1) drivers/mtd/nand/fsl_ifc_spl.c They are doing same way as OMAP used to. They are also using controller configurations to tell driver about the]NAND bus-width "port_size = (cspr & CSPR_PORT_SIZE_16) ? 16 : 8;" (2) drivers/mtd/nand/fsl_elbc_spl.c They are doing incomplete check. Rather they are not caring for x16 device For a x16 device, badblock marker should be 16-bit (2 bytes) but here they are checking of only 1st byte. "if (i++ < 2 && buf[page_offs + bad_marker] != 0xff)" So CONFIG_SYS_NAND_DEVICE_WIDTH should help them also. right ? So can this new CONFIG_xx be accepted ? > > > It looked > > > like you were removing the code that does dynamic detection, which > would > > > also affect non-SPL. > > > > > > > - /* If we are 16 bit dev, our gpmc config tells us that */ > > > > - if ((readl(&gpmc_cfg->cs[cs].config1) & 0x3000) == 0x1000) > > > > omap_gpmc.c never had dynamic detection support. Above gpmc_config > bit > > which is used to tell whether device is x16 or x8, gets actually hard-coded in > > gpmc_init(). Thus it was actually a mechanism to pass hard-coded bus- > width > > information to nand driver. > > Refer: arch/arm/cpu/armv7/am33xx/mem.c : gpmc_init() > > > > So, instead of hacking the gpmc_init() everytime for different devices, > > this patch introduces a generic CONFIG which can be used everywhere. > > It looks like you do more NAND config in gpmc_init() than just setting > this one bit, so I don't think you save anything here. > > BTW, do you not need to set this bit in the config register for the > hardware to work in the SPL case? > Yes, I'm not changing the default configs for GPMC in gpmc_init(), because they are ok for x8 device. I'm just overriding them again during board_nand_init() if CONFIG_SYS_NAND_DEVICE_WIDTH == x16 device. + /* reconfigure GPMC.CONFIG1 register with correct device-width */ + gpmc_config = readl(&gpmc_cfg->cs[cs].config1); + if (nand->options & NAND_BUSWIDTH_16) + gpmc_config |= (0x1 << 12); + else + gpmc_config &= ~(0x1 << 12); + writel(gpmc_config, &gpmc_cfg->cs[cs].config1); + This way im not breaking any backward compatibility, just avoiding the need to hack the board file for x16 devices. with regards, pekon

1 0

[U-Boot] [PATCH V5 00/18] Make mv_udc work for i.mx6
by Troy Kisky 28 Sep '13

28 Sep '13

Hi Marek, Stefano This series is based on u-boot-usb/master branch. After this series, nitrogen6x works with tftpboot to transfer files over usb, and will recognize a usb stick in the OTG port. This V5 has been rebased to the latest u-boot-usb/master branch and changed to address Marek comments. The most noticeable change is the removal of ehci_hcd_init_after_reset using CONFIG_EHCI_HCD_INIT_AFTER_RESET instead. Stefano, if you would you like to take the last 3 patches, you should apply "i.MX6Q/DLS: Add MX6_PAD_GPIO_1__USB_OTG_ID" from Eric Nelson first. The patches are mostly independent, so if a patch has an issue, please feel free to skip it. An exception is 1/17 should be before 2/17 if Stefano's branch merges upstream first, otherwise nitrogen6x will get a build error. Thanks Troy Kisky (18): usb: gadget: mv_udc: don't check CONFIG_USB_MAX_CONTROLLER_COUNT usb: ehci-mx6: add support for host mode otg port usb: echi-hcd: add usb_lowlevel_init_device usb: gadget: ether set wMaxPacketSize usb: gadget: ether: return error from rx_submit if no request usb: gadget: mv_udc: split mv_udc.h file usb: udc: add udc.h include file usb: gadget: mv_udc: fix typo in error message usb: gadget: mv_udc: set is_dualspeed = 1 usb: gadget: mv_udc: fix full speed connections usb: gadget: mv_udc: optimize bounce usb: gadget: mv_udc: flush item before head usb: gadget: mv_udc: optimize ep_enable usb: gadget: mv_udc: zero transfer descriptor memory on probe usb: gadget: mv_udc: clear desc upon ep_disable mx6: iomux: add GPR1 defines for use with nitrogen6x nitrogen6x: add otg usb host/device mode support nitrogen6x: add CONFIG_MV_UDC arch/arm/include/asm/arch-mx6/iomux.h | 6 ++ board/boundary/nitrogen6x/nitrogen6x.c | 33 +++++++++ drivers/serial/usbtty.h | 3 +- drivers/usb/gadget/designware_udc.c | 1 + drivers/usb/gadget/ether.c | 4 ++ drivers/usb/gadget/mpc8xx_udc.c | 1 + drivers/usb/gadget/mv_udc.c | 115 +++++++++++++++++------------- drivers/usb/gadget/mv_udc.h | 115 ++++++++++++++++++++++++++++++ drivers/usb/gadget/omap1510_udc.c | 1 + drivers/usb/gadget/pxa27x_udc.c | 1 + drivers/usb/host/ehci-hcd.c | 13 ++++ drivers/usb/host/ehci-mx6.c | 123 ++++++++++++++++++++++----------- drivers/usb/musb/musb_udc.c | 3 +- include/configs/mx6qsabreauto.h | 3 +- include/configs/nitrogen6x.h | 9 ++- include/usb.h | 1 + include/usb/designware_udc.h | 31 --------- include/usb/mpc8xx_udc.h | 19 +---- include/usb/musb_udc.h | 40 ----------- include/usb/mv_udc.h | 118 ------------------------------- include/usb/omap1510_udc.h | 31 ++------- include/usb/pxa27x_udc.h | 26 +------ include/usb/udc.h | 53 ++++++++++++++ 23 files changed, 401 insertions(+), 349 deletions(-) create mode 100644 drivers/usb/gadget/mv_udc.h delete mode 100644 include/usb/musb_udc.h create mode 100644 include/usb/udc.h -- 1.8.1.2

3 43

Re: [U-Boot] [PATCH 1/1] am33xx: add CONFIG_SYS_NAND_DEVICE_WIDTH to determine NAND device bus-width
by Scott Wood 27 Sep '13

27 Sep '13

On Fri, 2013-09-27 at 04:18 +0000, Gupta, Pekon wrote: > > From: Scott Wood [mailto:scottwood@freescale.com] > > > > On Thu, 2013-09-26 at 13:14 +0000, Gupta, Pekon wrote: > > > > > From: Gupta, Pekon <pekon(a)ti.com> > > > > > > > > > > NAND driver needs to know bus-width of the connected NAND device, > > in > > > > order to perform proper I/O and initialize itself. Currently there is no > > CONFIG > > > > option to provide this information to NAND driver. > > > > > - SPL NAND driver does not have framework to parse ONFI parameter > > > > page. > > > > > > > > Is this about SPL? It looks like a more general change. > > > > > > > Yes, actually I would have loved to see a generic SPL driver for all platforms, > > > > How could that possibly work? > > > NAND SPL (as in drivers/mtd/nand/am335x_spl_bch.c) had following limitation > (a) depends on CONFIG_SYS_NAND_xx (for NAND device parameters like > erasesize, pagesize, oobsize, etc). > (b) can only do NAND read access. > (c) calls nand_chip->ecc.hwctl() for doing controller specific > configurations, which is populated while doing board_nand_init(). > > Above (a), (b), and (c) do not have any SoC specific dependency. And can be > put into a generic framework which can be used for all SPL drivers. Not all NAND controllers expose a low-level interface that matches hwctl() (e.g. fsl_ifc and fsl_elbc). For those that do, we do have a common nand_spl_simple.c that works for many drivers, without needing to hardcode the bus width (though perhaps a few bytes could be shaved off by hardcoding it). BTW, referring to "driver" in NAND context is ambiguous... I prefer to use it to refer to the controller drivers when not qualified as "high level driver" or similar. > All SoC specific configurations are done in either: > - board_nand_init(): initializations based on device. > - nand_chip->ecc.hwctl(): configurations for ECC scheme. > which is *shared* code between SPL & u-boot driver, and is present in > u-boot driver file (like drivers/mtd/nand/omap_gpmc.c), not in SPL driver file. > > The missing piece was device bus-width detection which I addresses in > this patch by adding CONFIG_SYS_NAND_DEVICE_WIDTH. The changelog that introduced am335x_spl_bch.c says that "custom read_page implementation is required for proper syndrome generation." Other than that ECC mode, AFAICT you're already using nand_spl_simple.c. > > > because SPL is mostly statically configured, and it just does plain NAND read > > > (it doesn’t even support NAND write, etc). > > > But I do not know the hardware configurations tweaks of other SoC, > > > So at-least have common CONFIG_SYS_NAND_xx which all SPL drivers can > > use. > > > > Again, are you introducing this symbol for use only in SPL? > Apart from SPL, CONFIG_SYS_NAND_DEVICE_WIDTH also be useful for > (1) drivers which do not use CONFIG_SYS_NAND_ONFI_DETECTION, where > code for reading on-chip ONFI parameters is not enabled in nand_base.c > (2) non ONFI compatible NAND devices. Unlikely, given that they've all managed to work without this so far. E.g. eLBC and IFC hardcode this information on a per-chip basis in the #defines that hold values for config registers, and prior to this patch omap_gpmc had code to read a config register (regardless of where it originally got set). > > It looked > > like you were removing the code that does dynamic detection, which would > > also affect non-SPL. > > > > > - /* If we are 16 bit dev, our gpmc config tells us that */ > > > - if ((readl(&gpmc_cfg->cs[cs].config1) & 0x3000) == 0x1000) > > omap_gpmc.c never had dynamic detection support. Above gpmc_config bit > which is used to tell whether device is x16 or x8, gets actually hard-coded in > gpmc_init(). Thus it was actually a mechanism to pass hard-coded bus-width > information to nand driver. > Refer: arch/arm/cpu/armv7/am33xx/mem.c : gpmc_init() > > So, instead of hacking the gpmc_init() everytime for different devices, > this patch introduces a generic CONFIG which can be used everywhere. It looks like you do more NAND config in gpmc_init() than just setting this one bit, so I don't think you save anything here. BTW, do you not need to set this bit in the config register for the hardware to work in the SPL case? -Scott

1 0

[U-Boot] [PATCH][v2] powerpc/t1040qds: Add T1040QDS board
by Prabhakar Kushwaha 27 Sep '13

27 Sep '13

T1040QDS is a high-performance computing evaluation, development and test platform supporting the T1040 QorIQ Power Architecture™ processor. T1040QDS board Overview ----------------------- - Four e5500 cores, each with a private 256 KB L2 cache - 256 KB shared L3 CoreNet platform cache (CPC) - Interconnect CoreNet platform - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: - Packet parsing, classification, and distribution - Queue management for scheduling, packet sequencing, and congestion management - Cryptography Acceleration - RegEx Pattern Matching Acceleration - IEEE Std 1588 support - Hardware buffer management for buffer allocation and deallocation - Ethernet interfaces - Integrated 8-port Gigabit Ethernet switch - Four 1 Gbps Ethernet controllers - SERDES Connections, 8 lanes supporting: — PCI Express: supporting Gen 1 and Gen 2; — SGMII — QSGMII — SATA 2.0 — Aurora debug with dedicated connectors - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and Interleaving -IFC/Local Bus - NAND flash: 8-bit, async, up to 2GB. - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB - GASIC: Simple (minimal) target within Qixis FPGA - PromJET rapid memory download support - Ethernet - Two on-board RGMII 10/100/1G ethernet ports. - PHY #0 remains powered up during deep-sleep - QIXIS System Logic FPGA - Clocks - System and DDR clock (SYSCLK, “DDRCLK”) - SERDES clocks - Power Supplies - Video - DIU supports video at up to 1280x1024x32bpp - USB - Supports two USB 2.0 ports with integrated PHYs — Two type A ports with 5V(a)1.5A per port. — Second port can be converted to OTG mini-AB - SDHC - SDHC port connects directly to an adapter card slot, featuring: - Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC — Supporting eMMC memory devices - SPI - On-board support of 3 different devices and sizes - Other IO - Two Serial ports - ProfiBus port - Four I2C ports Signed-off-by: Poonam Aggrwal <poonam.aggrwal(a)freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain(a)freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar(a)freescale.com> --- This patch depends upon powerpc: Fix CamelCase checkpatch warning in DDR related code http://patchwork.ozlabs.org/patch/271670/ TODO: Add support of ethernet. Changes for v2: Incorporated Wolfgang Denk's comments - fix checkpatch warning - removed uncalled function MAINTAINERS | 2 + board/freescale/common/qixis.h | 4 +- board/freescale/t1040qds/Makefile | 37 ++ board/freescale/t1040qds/README | 169 +++++++ board/freescale/t1040qds/ddr.c | 117 +++++ board/freescale/t1040qds/ddr.h | 50 ++ board/freescale/t1040qds/law.c | 32 ++ board/freescale/t1040qds/pci.c | 23 + board/freescale/t1040qds/t1040qds.c | 255 ++++++++++ board/freescale/t1040qds/t1040qds.h | 13 + board/freescale/t1040qds/t1040qds_qixis.h | 36 ++ board/freescale/t1040qds/tlb.c | 108 ++++ boards.cfg | 1 + drivers/net/fm/Makefile | 1 + drivers/net/fm/t1040.c | 16 + include/configs/T1040QDS.h | 761 +++++++++++++++++++++++++++++ 16 files changed, 1624 insertions(+), 1 deletion(-) create mode 100644 board/freescale/t1040qds/Makefile create mode 100644 board/freescale/t1040qds/README create mode 100644 board/freescale/t1040qds/ddr.c create mode 100644 board/freescale/t1040qds/ddr.h create mode 100644 board/freescale/t1040qds/law.c create mode 100644 board/freescale/t1040qds/pci.c create mode 100644 board/freescale/t1040qds/t1040qds.c create mode 100644 board/freescale/t1040qds/t1040qds.h create mode 100644 board/freescale/t1040qds/t1040qds_qixis.h create mode 100644 board/freescale/t1040qds/tlb.c create mode 100644 drivers/net/fm/t1040.c create mode 100644 include/configs/T1040QDS.h diff --git a/MAINTAINERS b/MAINTAINERS index 0807727..52fbb86 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -27,6 +27,8 @@ Poonam Aggrwal <poonam.aggrwal(a)freescale.com> BSC9131RDB BSC9131 + T1040QDS T1040 + Naveen Burmi <NaveenBurmi(a)freescale.com> BSC9132QDS BSC9132 diff --git a/board/freescale/common/qixis.h b/board/freescale/common/qixis.h index 26e2eeb..d8fed14 100644 --- a/board/freescale/common/qixis.h +++ b/board/freescale/common/qixis.h @@ -79,7 +79,9 @@ struct qixis { u8 clk_freq[6]; /* Clock Measurement Registers */ u8 res_c6[8]; u8 clk_base[2]; /* Clock Frequency Base Reg */ - u8 res_d0[16]; + u8 res_d0[8]; + u8 cms[2]; /* Core Management Space Address Register, 0xD8 */ + u8 res_c0[6]; u8 aux2[4]; /* Auxiliary Registers,0xE0 */ u8 res14[10]; u8 aux_ad; diff --git a/board/freescale/t1040qds/Makefile b/board/freescale/t1040qds/Makefile new file mode 100644 index 0000000..8f0057b --- /dev/null +++ b/board/freescale/t1040qds/Makefile @@ -0,0 +1,37 @@ +# +# Copyright 2013 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-$(CONFIG_PCI) += pci.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/t1040qds/README b/board/freescale/t1040qds/README new file mode 100644 index 0000000..f8b53b4 --- /dev/null +++ b/board/freescale/t1040qds/README @@ -0,0 +1,169 @@ +Overview +-------- +The T1040QDS is a Freescale reference board that hosts the T1040 SoC +(and variants). + +T1040 SoC Overview +------------------ +The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA +processor cores with high-performance data path acceleration architecture +and network peripheral interfaces required for networking & telecommunications. + +The T1040/T1042 SoC includes the following function and features: + + - Four e5500 cores, each with a private 256 KB L2 cache + - 256 KB shared L3 CoreNet platform cache (CPC) + - Interconnect CoreNet platform + - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving + support + - Data Path Acceleration Architecture (DPAA) incorporating acceleration + for the following functions: + - Packet parsing, classification, and distribution + - Queue management for scheduling, packet sequencing, and congestion + management + - Cryptography Acceleration (SEC 5.0) + - RegEx Pattern Matching Acceleration (PME 2.2) + - IEEE Std 1588 support + - Hardware buffer management for buffer allocation and deallocation + - Ethernet interfaces + - Integrated 8-port Gigabit Ethernet switch (T1040 only) + - Four 1 Gbps Ethernet controllers + - Two RGMII interfaces or one RGMII and one MII interfaces + - High speed peripheral interfaces + - Four PCI Express 2.0 controllers running at up to 5 GHz + - Two SATA controllers supporting 1.5 and 3.0 Gb/s operation + - Upto two QSGMII interface + - Upto six SGMII interface supporting 1000 Mbps + - One SGMII interface supporting upto 2500 Mbps + - Additional peripheral interfaces + - Two USB 2.0 controllers with integrated PHY + - SD/eSDHC/eMMC + - eSPI controller + - Four I2C controllers + - Four UARTs + - Four GPIO controllers + - Integrated flash controller (IFC) + - LCD and HDMI interface (DIU) with 12 bit dual data rate + - TDM interface + - Multicore programmable interrupt controller (PIC) + - Two 8-channel DMA engines + - Single source clocking implementation + - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) + + T1040QDS board Overview + ----------------------- + - SERDES Connections, 8 lanes supporting: + — PCI Express: supporting Gen 1 and Gen 2; + — SGMII + — QSGMII + — SATA 2.0 + — Aurora debug with dedicated connectors (T1040 only) + - DDR Controller + - Supports rates of up to 1600 MHz data-rate + - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types. + -IFC/Local Bus + - NAND flash: 8-bit, async, up to 2GB. + - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB + - GASIC: Simple (minimal) target within Qixis FPGA + - PromJET rapid memory download support + - Ethernet + - Two on-board RGMII 10/100/1G ethernet ports. + - PHY #0 remains powered up during deep-sleep (T1040 only) + - QIXIS System Logic FPGA + - Clocks + - System and DDR clock (SYSCLK, “DDRCLK”) + - SERDES clocks + - Power Supplies + - Video + - DIU supports video at up to 1280x1024x32bpp + - USB + - Supports two USB 2.0 ports with integrated PHYs + — Two type A ports with 5V(a)1.5A per port. + — Second port can be converted to OTG mini-AB + - SDHC + - SDHC port connects directly to an adapter card slot, featuring: + - Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC + — Supporting eMMC memory devices + - SPI + - On-board support of 3 different devices and sizes + - Other IO + - Two Serial ports + - ProfiBus port + - Four I2C ports + +Memory map on T1040QDS +---------------------- +The addresses in brackets are physical addresses. + +Start Address End Address Description Size +0xF_FFDF_0000 0xF_FFDF_0FFF IFC - FPGA 4KB +0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB +0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB +0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB +0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB +0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB +0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB +0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB +0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB +0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB +0xF_E000_0000 0xF_E7FF_FFFF Promjet 128MB +0xF_0000_0000 0xF_003F_FFFF DCSR 4MB +0xC_3000_0000 0xC_3FFF_FFFF PCI Express 4 Mem Space 256MB +0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB +0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB +0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB +0x0_0000_0000 0x0_ffff_ffff DDR 2GB + + +NOR Flash memory Map on T1040QDS +-------------------------------- + Start End Definition Size +0xEFF80000 0xEFFFFFFF u-boot (current bank) 512KB +0xEFF60000 0xEFF7FFFF u-boot env (current bank) 128KB +0xEFF40000 0xEFF5FFFF FMAN Ucode (current bank) 128KB +0xED300000 0xEFF3FFFF rootfs (alt bank) 44MB + 256KB +0xEC800000 0xEC8FFFF Hardware device tree (alt bank) 1MB +0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB +0xEC000000 0xEC01FFFF RCW (alt bank) 128KB +0xEBF80000 0xEBFFFFFF u-boot (alt bank) 512KB +0xEBF60000 0xEBF7FFFF u-boot env (alt bank) 128KB +0xEBF40000 0xEBF5FFFF FMAN ucode (alt bank) 128KB +0xE9300000 0xEBF3FFFF rootfs (current bank) 44MB + 256KB +0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 11MB + 512KB +0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB +0xE8000000 0xE801FFFF RCW (current bank) 128KB + + +Various Software configurations/environment variables/commands +-------------------------------------------------------------- +The below commands apply to T1040QDS + +1. U-boot environment variable hwconfig + The default hwconfig is: + hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1: + dr_mode=host,phy_type=utmi + Note: For USB gadget set "dr_mode=peripheral" + +2. FMAN Ucode versions + fsl_fman_ucode_t1040.bin + +3. Switching to alternate bank + Commands for switching to alternate bank. + + 1. To change from vbank0 to vbank4 + => qixis_reset altbank (it will boot using vbank4) + + 2.To change from vbank4 to vbank0 + => qixis reset (it will boot using vbank0) + +T1040 Personality +-------------------- + +T1022 Personality +-------------------- +T1022 is a reduced personality of T1040 with less core/clusters. + +T1042 Personality +-------------------- +T1042 is a reduced personality of T1040 without Integrated 8-port Gigabit +Ethernet switch. Rest of the blocks are same as T1040 diff --git a/board/freescale/t1040qds/ddr.c b/board/freescale/t1040qds/ddr.c new file mode 100644 index 0000000..4fd17da --- /dev/null +++ b/board/freescale/t1040qds/ddr.c @@ -0,0 +1,117 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <hwconfig.h> +#include <asm/mmu.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> +#include <asm/fsl_law.h> +#include "ddr.h" + +DECLARE_GLOBAL_DATA_PTR; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; + ulong ddr_freq; + + if (ctrl_num > 2) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + if (!pdimm->n_ranks) + return; + + pbsp = udimms[0]; + + /* Get clk_adjust, cpo, write_data_delay,2t, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + while (pbsp->datarate_mhz_high) { + if (pbsp->n_ranks == pdimm->n_ranks && + (pdimm->rank_density >> 30) >= pbsp->rank_gb) { + if (ddr_freq <= pbsp->datarate_mhz_high) { + popts->cpo_override = pbsp->cpo; + popts->write_data_delay = + pbsp->write_data_delay; + popts->clk_adjust = pbsp->clk_adjust; + popts->wrlvl_start = pbsp->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + popts->twot_en = pbsp->force_2t; + goto found; + } + pbsp_highest = pbsp; + } + pbsp++; + } + + if (pbsp_highest) { + printf("Error: board specific timing not found\n"); + printf("for data rate %lu MT/s\n", ddr_freq); + printf("Trying to use the highest speed (%u) parameters\n", + pbsp_highest->datarate_mhz_high); + popts->cpo_override = pbsp_highest->cpo; + popts->write_data_delay = pbsp_highest->write_data_delay; + popts->clk_adjust = pbsp_highest->clk_adjust; + popts->wrlvl_start = pbsp_highest->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + popts->twot_en = pbsp_highest->force_2t; + } else { + panic("DIMM is not supported by this board"); + } +found: + debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n" + "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, " + "wrlvl_ctrl_3 0x%x\n", + pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb, + pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2, + pbsp->wrlvl_ctl_3); + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * rtt and rtt_wr override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size; + + puts("Initializing....using SPD\n"); + + dram_size = fsl_ddr_sdram(); + + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; + + puts(" DDR: "); + return dram_size; +} diff --git a/board/freescale/t1040qds/ddr.h b/board/freescale/t1040qds/ddr.h new file mode 100644 index 0000000..8ee206e --- /dev/null +++ b/board/freescale/t1040qds/ddr.h @@ -0,0 +1,50 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __DDR_H__ +#define __DDR_H__ +struct board_specific_parameters { + u32 n_ranks; + u32 datarate_mhz_high; + u32 rank_gb; + u32 clk_adjust; + u32 wrlvl_start; + u32 wrlvl_ctl_2; + u32 wrlvl_ctl_3; + u32 cpo; + u32 write_data_delay; + u32 force_2t; +}; + +/* + * These tables contain all valid speeds we want to override with board + * specific parameters. datarate_mhz_high values need to be in ascending order + * for each n_ranks group. + */ + +static const struct board_specific_parameters udimm0[] = { + /* + * memory controller 0 + * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T + * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay | + */ + {2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, + {2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09, 0xff, 2, 0}, + {2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b, 0xff, 2, 0}, + {2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a, 0xff, 2, 0}, + {2, 1900, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0}, + {2, 2140, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0}, + {1, 1350, 0, 5, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, + {1, 1700, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0}, + {1, 1900, 0, 4, 8, 0x080a0a0c, 0x0e0e0f0a, 0xff, 2, 0}, + {1, 2140, 0, 4, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0}, + {} +}; + +static const struct board_specific_parameters *udimms[] = { + udimm0, +}; +#endif diff --git a/board/freescale/t1040qds/law.c b/board/freescale/t1040qds/law.c new file mode 100644 index 0000000..a2dc027 --- /dev/null +++ b/board/freescale/t1040qds/law.c @@ -0,0 +1,32 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { +#ifndef CONFIG_SYS_NO_FLASH + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), +#endif +#ifdef QIXIS_BASE_PHYS + SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/t1040qds/pci.c b/board/freescale/t1040qds/pci.c new file mode 100644 index 0000000..c53e3b7 --- /dev/null +++ b/board/freescale/t1040qds/pci.c @@ -0,0 +1,23 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/fsl_pci.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <asm/fsl_serdes.h> + +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/freescale/t1040qds/t1040qds.c b/board/freescale/t1040qds/t1040qds.c new file mode 100644 index 0000000..5abb18a --- /dev/null +++ b/board/freescale/t1040qds/t1040qds.c @@ -0,0 +1,255 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <i2c.h> +#include <netdev.h> +#include <linux/compiler.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <fm_eth.h> + +#include "../common/qixis.h" +#include "t1040qds.h" +#include "t1040qds_qixis.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + char buf[64]; + u8 sw; + struct cpu_type *cpu = gd->arch.cpu; + static const char *const freq[] = {"100", "125", "156.25", "161.13", + "122.88", "122.88", "122.88"}; + int clock; + + printf("Board: %sQDS, ", cpu->name); + printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, ", + QIXIS_READ(id), QIXIS_READ(arch)); + + sw = QIXIS_READ(brdcfg[0]); + sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; + + if (sw < 0x8) + printf("vBank: %d\n", sw); + else if (sw == 0x8) + puts("PromJet\n"); + else if (sw == 0x9) + puts("NAND\n"); + else if (sw == 0x15) + printf("IFCCard\n"); + else + printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH); + + printf("FPGA: v%d (%s), build %d", + (int)QIXIS_READ(scver), qixis_read_tag(buf), + (int)qixis_read_minor()); + /* the timestamp string contains "\n" at the end */ + printf(" on %s", qixis_read_time(buf)); + + /* + * Display the actual SERDES reference clocks as configured by the + * dip switches on the board. Note that the SWx registers could + * technically be set to force the reference clocks to match the + * values that the SERDES expects (or vice versa). For now, however, + * we just display both values and hope the user notices when they + * don't match. + */ + puts("SERDES Reference: "); + sw = QIXIS_READ(brdcfg[2]); + clock = (sw >> 6) & 3; + printf("Clock1=%sMHz ", freq[clock]); + clock = (sw >> 4) & 3; + printf("Clock2=%sMHz\n", freq[clock]); + + return 0; +} + +int select_i2c_ch_pca9547(u8 ch) +{ + int ret; + + ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); + if (ret) { + puts("PCA: failed to select proper channel\n"); + return ret; + } + + return 0; +} + +int board_early_init_r(void) +{ +#ifdef CONFIG_SYS_FLASH_BASE + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash + PROMJET region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash + promjet */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); +#endif + set_liodns(); +#ifdef CONFIG_SYS_DPAA_QBMAN + setup_portals(); +#endif + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + + return 0; +} + +unsigned long get_board_sys_clk(void) +{ + u8 sysclk_conf = QIXIS_READ(brdcfg[1]); + + switch (sysclk_conf & 0x0F) { + case QIXIS_SYSCLK_64: + return 64000000; + case QIXIS_SYSCLK_83: + return 83333333; + case QIXIS_SYSCLK_100: + return 100000000; + case QIXIS_SYSCLK_125: + return 125000000; + case QIXIS_SYSCLK_133: + return 133333333; + case QIXIS_SYSCLK_150: + return 150000000; + case QIXIS_SYSCLK_160: + return 160000000; + case QIXIS_SYSCLK_166: + return 166666666; + } + return 66666666; +} + +unsigned long get_board_ddr_clk(void) +{ + u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); + + switch ((ddrclk_conf & 0x30) >> 4) { + case QIXIS_DDRCLK_100: + return 100000000; + case QIXIS_DDRCLK_125: + return 125000000; + case QIXIS_DDRCLK_133: + return 133333333; + } + return 66666666; +} + +static const char *serdes_clock_to_string(u32 clock) +{ + switch (clock) { + case SRDS_PLLCR0_RFCK_SEL_100: + return "100"; + case SRDS_PLLCR0_RFCK_SEL_125: + return "125"; + case SRDS_PLLCR0_RFCK_SEL_156_25: + return "156.25"; + default: + return "Unknown frequency"; + } +} + +#define NUM_SRDS_BANKS 2 +int misc_init_r(void) +{ + u8 sw; + serdes_corenet_t *srds_regs = + (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; + u32 actual[NUM_SRDS_BANKS] = { 0 }; + int i; + + sw = QIXIS_READ(brdcfg[2]); + for (i = 0; i < NUM_SRDS_BANKS; i++) { + unsigned int clock = (sw >> (6 - 2 * i)) & 3; + switch (clock) { + case 0: + actual[i] = SRDS_PLLCR0_RFCK_SEL_100; + break; + case 1: + actual[i] = SRDS_PLLCR0_RFCK_SEL_125; + break; + case 2: + actual[i] = SRDS_PLLCR0_RFCK_SEL_156_25; + break; + } + } + + puts("SerDes1"); + for (i = 0; i < NUM_SRDS_BANKS; i++) { + u32 pllcr0 = srds_regs->bank[i].pllcr0; + u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK; + if (expected != actual[i]) { + printf("expects ref clk%d %sMHz, but actual is %sMHz\n", + i + 1, serdes_clock_to_string(expected), + serdes_clock_to_string(actual[i])); + } + } + + return 0; +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); + +#ifdef CONFIG_HAS_FSL_DR_USB + fdt_fixup_dr_usb(blob, bd); +#endif + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); +#endif +} + +void qixis_dump_switch(void) +{ + int i, nr_of_cfgsw; + + QIXIS_WRITE(cms[0], 0x00); + nr_of_cfgsw = QIXIS_READ(cms[1]); + + puts("DIP switch settings dump:\n"); + for (i = 1; i <= nr_of_cfgsw; i++) { + QIXIS_WRITE(cms[0], i); + printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1])); + } +} diff --git a/board/freescale/t1040qds/t1040qds.h b/board/freescale/t1040qds/t1040qds.h new file mode 100644 index 0000000..79bdeda --- /dev/null +++ b/board/freescale/t1040qds/t1040qds.h @@ -0,0 +1,13 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __T1040_QDS_H__ +#define __T1040_QDS_H__ + +void fdt_fixup_board_enet(void *blob); +void pci_of_setup(void *blob, bd_t *bd); + +#endif diff --git a/board/freescale/t1040qds/t1040qds_qixis.h b/board/freescale/t1040qds/t1040qds_qixis.h new file mode 100644 index 0000000..2ce8795 --- /dev/null +++ b/board/freescale/t1040qds/t1040qds_qixis.h @@ -0,0 +1,36 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __T1040QDS_QIXIS_H__ +#define __T1040QDS_QIXIS_H__ + +/* Definitions of QIXIS Registers for T1040QDS */ + +/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */ +#define BRDCFG4_EMISEL_MASK 0xE0 +#define BRDCFG4_EMISEL_SHIFT 5 + +/* SYSCLK */ +#define QIXIS_SYSCLK_66 0x0 +#define QIXIS_SYSCLK_83 0x1 +#define QIXIS_SYSCLK_100 0x2 +#define QIXIS_SYSCLK_125 0x3 +#define QIXIS_SYSCLK_133 0x4 +#define QIXIS_SYSCLK_150 0x5 +#define QIXIS_SYSCLK_160 0x6 +#define QIXIS_SYSCLK_166 0x7 +#define QIXIS_SYSCLK_64 0x8 + +/* DDRCLK */ +#define QIXIS_DDRCLK_66 0x0 +#define QIXIS_DDRCLK_100 0x1 +#define QIXIS_DDRCLK_125 0x2 +#define QIXIS_DDRCLK_133 0x3 + + +#define QIXIS_SRDS1CLK_122 0x5a +#define QIXIS_SRDS1CLK_125 0x5e +#endif diff --git a/board/freescale/t1040qds/tlb.c b/board/freescale/t1040qds/tlb.c new file mode 100644 index 0000000..412c591 --- /dev/null +++ b/board/freescale/t1040qds/tlb.c @@ -0,0 +1,108 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ +#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) + /* + * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the + * SRAM is at 0xfffc0000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256K, 1), +#else + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#endif + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + + /* *I*G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256K, 1), + + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 5, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 7, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 8, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 9, BOOKE_PAGESZ_4M, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE + /* + * *I*G - NAND + * entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so we use entry 16 for nand. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_64K, 1), +#endif +#ifdef QIXIS_BASE + SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 11, BOOKE_PAGESZ_4K, 1), +#endif + +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index 48aa0bf..1aa4f82 100644 --- a/boards.cfg +++ b/boards.cfg @@ -955,6 +955,7 @@ B4860QDS_SRIO_PCIE_BOOT powerpc mpc85xx b4860qds freesca B4420QDS powerpc mpc85xx b4860qds freescale - B4860QDS:PPC_B4420 B4420QDS_NAND powerpc mpc85xx b4860qds freescale - B4860QDS:PPC_B4420,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000 B4420QDS_SPIFLASH powerpc mpc85xx b4860qds freescale - B4860QDS:PPC_B4420,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 +T1040QDS powerpc mpc85xx t1040qds freescale - T1040QDS:PPC_T1040 xpedite520x powerpc mpc85xx - xes xpedite537x powerpc mpc85xx - xes xpedite550x powerpc mpc85xx - xes diff --git a/drivers/net/fm/Makefile b/drivers/net/fm/Makefile index 4edd849..dddde4f 100644 --- a/drivers/net/fm/Makefile +++ b/drivers/net/fm/Makefile @@ -29,6 +29,7 @@ COBJS-$(CONFIG_PPC_P3041) += p5020.o COBJS-$(CONFIG_PPC_P4080) += p4080.o COBJS-$(CONFIG_PPC_P5020) += p5020.o COBJS-$(CONFIG_PPC_P5040) += p5040.o +COBJS-$(CONFIG_PPC_T1040) += t1040.o COBJS-$(CONFIG_PPC_T4240) += t4240.o COBJS-$(CONFIG_PPC_T4160) += t4240.o COBJS-$(CONFIG_PPC_B4420) += b4860.o diff --git a/drivers/net/fm/t1040.c b/drivers/net/fm/t1040.c new file mode 100644 index 0000000..83cf081 --- /dev/null +++ b/drivers/net/fm/t1040.c @@ -0,0 +1,16 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#include <common.h> +#include <phy.h> +#include <fm_eth.h> +#include <asm/io.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_serdes.h> + +phy_interface_t fman_port_enet_if(enum fm_port port) +{ + return PHY_INTERFACE_MODE_NONE; +} diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h new file mode 100644 index 0000000..2738242 --- /dev/null +++ b/include/configs/T1040QDS.h @@ -0,0 +1,761 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * T1040 QDS board configuration file + */ +#define CONFIG_T1040QDS +#define CONFIG_PHYS_64BIT + +#ifdef CONFIG_RAMBOOT_PBL +#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#endif + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_E500MC /* BOOKE e500mc family */ +#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ +#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */ +#define CONFIG_MP /* support multiple processors */ + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff80000 +#endif + +#ifndef CONFIG_RESET_VECTOR_ADDRESS +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc +#endif + +#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ +#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS +#define CONFIG_FSL_IFC /* Enable IFC Support */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_PCIE2 /* PCIE controler 2 */ +#define CONFIG_PCIE3 /* PCIE controler 3 */ +#define CONFIG_PCIE4 /* PCIE controler 4 */ + +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +#define CONFIG_ENV_OVERWRITE + +#ifdef CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_NOWHERE +#else +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#endif + +#ifndef CONFIG_SYS_NO_FLASH +#if defined(CONFIG_SPIFLASH) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ +#define CONFIG_ENV_SECT_SIZE 0x10000 +#elif defined(CONFIG_SDCARD) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_OFFSET (512 * 1105) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif +#else /* CONFIG_SYS_NO_FLASH */ +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif + +#ifndef __ASSEMBLY__ +unsigned long get_board_sys_clk(void); +unsigned long get_board_ddr_clk(void); +#endif + +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_SYS_CACHE_STASHING +#define CONFIG_BACKSIDE_L2_CACHE +#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_DDR_ECC +#ifdef CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#endif + +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ + +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* + * Config the L3 Cache as L3 SRAM + */ +#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 + +#define CONFIG_SYS_DCSRBAR 0xf0000000 +#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +/* + * DDR Setup + */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */ +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) + +#define CONFIG_DDR_SPD +#define CONFIG_FSL_DDR3 +#define CONFIG_FSL_DDR_INTERACTIVE + +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x51 + +#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ + +/* + * IFC Definitions + */ +#define CONFIG_SYS_FLASH_BASE 0xe0000000 +#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) + +#define CONFIG_SYS_NOR0_CSPR_EXT (0xf) +#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ + + 0x8000000) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR1_CSPR_EXT (0xf) +#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) +/* NOR Flash Timing Params */ +#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ + FTIM0_NOR_TEADC(0x5) | \ + FTIM0_NOR_TEAHC(0x5)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ + FTIM1_NOR_TRAD_NOR(0x1A) |\ + FTIM1_NOR_TSEQRAD_NOR(0x13)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ + FTIM2_NOR_TCH(0x4) | \ + FTIM2_NOR_TWPH(0x0E) | \ + FTIM2_NOR_TWP(0x1c)) +#define CONFIG_SYS_NOR_FTIM3 0x0 + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ + + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} +#define CONFIG_FSL_QIXIS /* use common QIXIS code */ +#define QIXIS_BASE 0xffdf0000 +#define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) +#define QIXIS_LBMAP_SWITCH 0x06 +#define QIXIS_LBMAP_MASK 0x0f +#define QIXIS_LBMAP_SHIFT 0 +#define QIXIS_LBMAP_DFLTBANK 0x00 +#define QIXIS_LBMAP_ALTBANK 0x04 +#define QIXIS_RST_CTL_RESET 0x31 +#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 +#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 +#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 + +#define CONFIG_SYS_CSPR3_EXT (0xf) +#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_GPCM \ + | CSPR_V) +#define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024) +#define CONFIG_SYS_CSOR3 0x0 +/* QIXIS Timing parameters for IFC CS3 */ +#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ + FTIM0_GPCM_TEADC(0x0e) | \ + FTIM0_GPCM_TEAHC(0x0e)) +#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ + FTIM1_GPCM_TRAD(0x3f)) +#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ + FTIM2_GPCM_TCH(0x0) | \ + FTIM2_GPCM_TWP(0x1f)) +#define CONFIG_SYS_CS3_FTIM3 0x0 + +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_BASE 0xff800000 +#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) + +#define CONFIG_SYS_NAND_CSPR_EXT (0xf) +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ + | CSPR_MSEL_NAND /* MSEL = NAND */ \ + | CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) + +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ + | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ + | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ + | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ + | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +/* ONFI NAND Flash mode0 Timing Params */ +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ + FTIM0_NAND_TWP(0x18) | \ + FTIM0_NAND_TWCHT(0x07) | \ + FTIM0_NAND_TWH(0x0a)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ + FTIM1_NAND_TWBE(0x39) | \ + FTIM1_NAND_TRR(0x0e) | \ + FTIM1_NAND_TRP(0x18)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ + FTIM2_NAND_TREH(0x0a) | \ + FTIM2_NAND_TWHRE(0x1e)) +#define CONFIG_SYS_NAND_FTIM3 0x0 + +#define CONFIG_SYS_NAND_DDR_LAW 11 +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND + +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +#if defined(CONFIG_NAND) +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT +#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR +#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 +#else +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 +#endif + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#if defined(CONFIG_RAMBOOT_PBL) +#define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_MISC_INIT_R + +#define CONFIG_HWCONFIG + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) +#define CONFIG_SERIAL_MULTI /* Enable both serial ports */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ +#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000 + +#define I2C_MUX_PCA_ADDR 0x77 +#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/ + + +/* I2C bus multiplexer */ +#define I2C_MUX_CH_DEFAULT 0x8 + +/* + * RTC configuration + */ +#define RTC +#define CONFIG_RTC_DS3231 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_FSL_ESPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SPI_FLASH_SST +#define CONFIG_SPI_FLASH_EON +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE 0 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +#ifdef CONFIG_PCI +/* controller 1, direct to uli, tgtid 3, Base address 20000 */ +#ifdef CONFIG_PCIE1 +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 2, Slot 2, tgtid 2, Base address 201000 */ +#ifdef CONFIG_PCIE2 +#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 3, Slot 1, tgtid 1, Base address 202000 */ +#ifdef CONFIG_PCIE3 +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 4, Base address 203000 */ +#ifdef CONFIG_PCIE4 +#define CONFIG_SYS_PCIE4_MEM_VIRT 0xb0000000 +#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc30000000ull +#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE4_IO_VIRT 0xf8030000 +#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull +#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ +#endif + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_E1000 + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif /* CONFIG_PCI */ + +/* SATA */ +#define CONFIG_FSL_SATA_V2 +#ifdef CONFIG_FSL_SATA_V2 +#define CONFIG_LIBATA +#define CONFIG_FSL_SATA + +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SATA2 +#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA + +#define CONFIG_LBA48 +#define CONFIG_CMD_SATA +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +#endif + +/* +* USB +*/ +#define CONFIG_HAS_FSL_DR_USB + +#ifdef CONFIG_HAS_FSL_DR_USB +#define CONFIG_USB_EHCI + +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_CMD_EXT2 +#endif +#endif + +#define CONFIG_MMC + +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* Qman/Bman */ +#ifndef CONFIG_NOBQFMAN +#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ +#define CONFIG_SYS_BMAN_NUM_PORTALS 25 +#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 +#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull +#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 +#define CONFIG_SYS_QMAN_NUM_PORTALS 25 +#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 +#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull +#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 + +#define CONFIG_SYS_DPAA_FMAN +#define CONFIG_SYS_DPAA_PME + +/* Default address of microcode for the Linux Fman driver */ +#if defined(CONFIG_SPIFLASH) +/* + * env is stored at 0x100000, sector size is 0x10000, ucode is stored after + * env, so we got 0x110000. + */ +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000 +#elif defined(CONFIG_SDCARD) +/* + * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is + * about 545KB (1089 blocks), Env is stored after the image, and the env size is + * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_MMC +#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_QE_FMAN_FW_IN_NAND +#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000 +#endif +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) +#endif /* CONFIG_NOBQFMAN */ + +#ifdef CONFIG_SYS_DPAA_FMAN +#define CONFIG_FMAN_ENET +#define CONFIG_PHYLIB_10G +#define CONFIG_PHY_VITESSE +#define CONFIG_PHY_REALTEK +#define CONFIG_PHY_TERANETICS +#define SGMII_CARD_PORT1_PHY_ADDR 0x1C +#define SGMII_CARD_PORT2_PHY_ADDR 0x10 +#define SGMII_CARD_PORT3_PHY_ADDR 0x1E +#define SGMII_CARD_PORT4_PHY_ADDR 0x11 +#endif + +#ifdef CONFIG_FMAN_ENET +#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x10 +#define CONFIG_SYS_FM1_DTSEC6_PHY_ADDR 0x11 +#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 4 + +#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c +#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d +#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e +#define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC1" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* + * Environment + */ +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ERRATA +#define CONFIG_CMD_GREPENV +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SETEXPR + +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ + +#define CONFIG_BAUDRATE 115200 + +#define __USB_PHY_TYPE utmi + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ + "bank_intlv=cs0_cs1;" \ + "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ + "netdev=eth0\0" \ + "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ + "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot && " \ + "protect off $ubootaddr +$filesize && " \ + "erase $ubootaddr +$filesize && " \ + "cp.b $loadaddr $ubootaddr $filesize && " \ + "protect on $ubootaddr +$filesize && " \ + "cmp.b $loadaddr $ubootaddr $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=t1040qds/ramdisk.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=t1040qds/t1040qds.dtb\0" \ + "bdev=sda3\0" \ + "c=ffe\0" + +#define CONFIG_LINUX \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "setenv ramdiskaddr 0x02000000;" \ + "setenv fdtaddr 0x00c00000;" \ + "setenv loadaddr 0x1000000;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_HDBOOT \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_LINUX + +#ifdef CONFIG_SECURE_BOOT +#include <asm/fsl_secure_boot.h> +#endif + +#endif /* __CONFIG_H */ -- 1.7.9.5

2 1

[U-Boot] [PATCH 0/1] Fix ethernet regression on pcm051
by Lars Poeschel 27 Sep '13

27 Sep '13

From: Lars Poeschel <poeschel(a)lemonage.de> I compiled and tried v2013.10-rc2 on pcm051 and it fails booting over tftp. I could bisect 2bf36ac638ab2db9f0295aa47064976eeebf80c1 as the cause of the problem. It moves bd_ram_ofs from the cpsw driver to the board files. Adding the bd_ram_ofs to the board file of pcm051 fixes the problem. That is what the patch does. A quick grep reveals, that igep0033 MAY also be affected. As the patch is simple and obivous and fixes a regression I'd like to get this in before the v2013.10 release. Thanks Lars Poeschel (1): pcm051: Supply a bd_ram_ofs for the cpsw driver board/phytec/pcm051/board.c | 1 + 1 file changed, 1 insertion(+) -- 1.8.4.rc3

3 3

[U-Boot] [PATCH] powerpc/tool/pbl: fix pbl image compiling process
by shh.xie＠gmail.com 27 Sep '13

27 Sep '13

From: Shaohui Xie <Shaohui.Xie(a)freescale.com> Previous process of compiling a PBL boot image is: 1: make <board_name_config> 2: make u-boot.pbl for example: make T4240QDS_SDCARD_config make u-boot.pbl Now the process is: 1: make <board_name> for example: make T4240QDS_SDCARD Also, updated README.pblimage. Signed-off-by: Shaohui Xie <Shaohui.Xie(a)freescale.com> --- Makefile | 1 + doc/README.pblimage | 15 ++++++--------- 2 files changed, 7 insertions(+), 9 deletions(-) diff --git a/Makefile b/Makefile index 8aa8039..9ae1719 100644 --- a/Makefile +++ b/Makefile @@ -397,6 +397,7 @@ ALL-y += $(obj)u-boot.srec $(obj)u-boot.bin $(obj)System.map ALL-$(CONFIG_NAND_U_BOOT) += $(obj)u-boot-nand.bin ALL-$(CONFIG_ONENAND_U_BOOT) += $(obj)u-boot-onenand.bin +ALL-$(CONFIG_RAMBOOT_PBL) += $(obj)u-boot.pbl ALL-$(CONFIG_SPL) += $(obj)spl/u-boot-spl.bin ALL-$(CONFIG_SPL_FRAMEWORK) += $(obj)u-boot.img ALL-$(CONFIG_TPL) += $(obj)tpl/u-boot-tpl.bin diff --git a/doc/README.pblimage b/doc/README.pblimage index 2b9bb5c..7fdd26b 100644 --- a/doc/README.pblimage +++ b/doc/README.pblimage @@ -14,20 +14,17 @@ Building PBL Boot Image and boot steps 1. Building PBL Boot Image. The default Image is u-boot.pbl. - For eSPI boot(available on P3041/P4080/P5020): + For eSPI boot(available on P2041/P3041/P4080/P5020/P5040/T4240): To build the eSPI boot image: - make <board_name>_SPIFLASH_config - make u-boot.pbl + make <board_name>_SPIFLASH - For SD boot(available on P3041/P4080/P5020): + For SD boot(available on P2041/P3041/P4080/P5020/P5040/T4240): To build the SD boot image: - make <board_name>_SDCARD_config - make u-boot.pbl + make <board_name>_SDCARD - For Nand boot(available on P3041/P5020): + For Nand boot(available on P2041/P3041/P5020/P5040): To build the NAND boot image: - make <board_name>_NAND_config - make u-boot.pbl + make <board_name>_NAND 2. pblimage support available with mkimage utility will generate Freescale PBL -- 1.7.0.4

2 2