April 2022 - U-Boot

[PATCH] board: gateworks: gw_ventana: remove obsolete file
by Tim Harvey 20 May '22

20 May '22

commit 61cf22505339 ("board: gateworks: gw_ventana: use comomn GSC driver") moved to the common GSC driver and moved remaining board-specific functions to eeprom.c. The functions in gsc.c are no longer used and it was removed from the Makefile but the file itself was not removed. Remove it now. Signed-off-by: Tim Harvey <tharvey(a)gateworks.com> --- board/gateworks/gw_ventana/gsc.c | 471 ------------------------------- 1 file changed, 471 deletions(-) delete mode 100644 board/gateworks/gw_ventana/gsc.c diff --git a/board/gateworks/gw_ventana/gsc.c b/board/gateworks/gw_ventana/gsc.c deleted file mode 100644 index 46448a54db90..000000000000 --- a/board/gateworks/gw_ventana/gsc.c +++ /dev/null @@ -1,471 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2013 Gateworks Corporation - * - * Author: Tim Harvey <tharvey(a)gateworks.com> - */ - -#include <common.h> -#include <command.h> -#include <log.h> -#include <linux/delay.h> -#include <linux/errno.h> -#include <common.h> -#include <i2c.h> -#include <linux/ctype.h> - -#include <asm/arch/sys_proto.h> -#include <asm/global_data.h> -#include <dm/device.h> -#include <dm/uclass.h> - -#include "ventana_eeprom.h" -#include "gsc.h" - -DECLARE_GLOBAL_DATA_PTR; - -#if CONFIG_IS_ENABLED(DM_I2C) -struct udevice *i2c_get_dev(int busno, int slave) -{ - struct udevice *dev, *bus; - int ret; - - ret = uclass_get_device_by_seq(UCLASS_I2C, busno, &bus); - if (ret) - return NULL; - ret = dm_i2c_probe(bus, slave, 0, &dev); - if (ret) - return NULL; - - return dev; -} -#endif - -/* - * The Gateworks System Controller will fail to ACK a master transaction if - * it is busy, which can occur during its 1HZ timer tick while reading ADC's. - * When this does occur, it will never be busy long enough to fail more than - * 2 back-to-back transfers. Thus we wrap i2c_read and i2c_write with - * 3 retries. - */ -int gsc_i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len) -{ - int retry = 3; - int n = 0; - int ret; -#if CONFIG_IS_ENABLED(DM_I2C) - struct udevice *dev; - - dev = i2c_get_dev(CONFIG_I2C_GSC, chip); - if (!dev) - return -ENODEV; - ret = i2c_set_chip_offset_len(dev, alen); - if (ret) { - puts("EEPROM: Failed to set alen\n"); - return ret; - } -#else - i2c_set_bus_num(CONFIG_I2C_GSC); -#endif - - while (n++ < retry) { -#if CONFIG_IS_ENABLED(DM_I2C) - ret = dm_i2c_read(dev, addr, buf, len); -#else - ret = i2c_read(chip, addr, alen, buf, len); -#endif - if (!ret) - break; - debug("%s: 0x%02x 0x%02x retry%d: %d\n", __func__, chip, addr, - n, ret); - if (ret != -EREMOTEIO) - break; - mdelay(10); - } - return ret; -} - -int gsc_i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len) -{ - int retry = 3; - int n = 0; - int ret; -#if CONFIG_IS_ENABLED(DM_I2C) - struct udevice *dev; - - dev = i2c_get_dev(CONFIG_I2C_GSC, chip); - if (!dev) - return -ENODEV; - ret = i2c_set_chip_offset_len(dev, alen); - if (ret) { - puts("EEPROM: Failed to set alen\n"); - return ret; - } -#endif - - while (n++ < retry) { -#if CONFIG_IS_ENABLED(DM_I2C) - ret = dm_i2c_write(dev, addr, buf, len); -#else - ret = i2c_write(chip, addr, alen, buf, len); -#endif - if (!ret) - break; - debug("%s: 0x%02x 0x%02x retry%d: %d\n", __func__, chip, addr, - n, ret); - if (ret != -EREMOTEIO) - break; - mdelay(10); - } - mdelay(100); - return ret; -} - -int gsc_get_board_temp(void) -{ - const void *fdt = gd->fdt_blob; - int node, reg, mode, val; - const char *label; - u8 buf[2]; - int ret; - - node = fdt_node_offset_by_compatible(fdt, -1, "gw,gsc-adc"); - if (node <= 0) - return node; - - /* iterate over hwmon nodes */ - node = fdt_first_subnode(fdt, node); - while (node > 0) { - reg = fdtdec_get_int(fdt, node, "reg", -1); - mode = fdtdec_get_int(fdt, node, "gw,mode", -1); - label = fdt_stringlist_get(fdt, node, "label", 0, NULL); - - if ((reg == -1) || (mode == -1) || !label) { - printf("invalid dt:%s\n", fdt_get_name(fdt, node, NULL)); - continue; - } - - if ((mode != 0) || strcmp(label, "temp")) - continue; - - memset(buf, 0, sizeof(buf)); - ret = gsc_i2c_read(GSC_HWMON_ADDR, reg, 1, buf, sizeof(buf)); - val = buf[0] | buf[1] << 8; - if (val >= 0) { - if (val > 0x8000) - val -= 0xffff; - return val; - } - node = fdt_next_subnode(fdt, node); - } - - return 0; -} - -/* display hardware monitor ADC channels */ -int gsc_hwmon(void) -{ - const void *fdt = gd->fdt_blob; - int node, reg, mode, len, val, offset; - const char *label; - u8 buf[2]; - int ret; - - node = fdt_node_offset_by_compatible(fdt, -1, "gw,gsc-adc"); - if (node <= 0) - return node; - - /* iterate over hwmon nodes */ - node = fdt_first_subnode(fdt, node); - while (node > 0) { - reg = fdtdec_get_int(fdt, node, "reg", -1); - mode = fdtdec_get_int(fdt, node, "gw,mode", -1); - offset = fdtdec_get_int(fdt, node, "gw,voltage-offset-microvolt", 0); - label = fdt_stringlist_get(fdt, node, "label", 0, NULL); - - if ((reg == -1) || (mode == -1) || !label) - printf("invalid dt:%s\n", fdt_get_name(fdt, node, NULL)); - - memset(buf, 0, sizeof(buf)); - ret = gsc_i2c_read(GSC_HWMON_ADDR, reg, 1, buf, sizeof(buf)); - val = buf[0] | buf[1] << 8; - if (val >= 0) { - const u32 *div; - int r[2]; - - switch (mode) { - case 0: /* temperature (C*10) */ - if (val > 0x8000) - val -= 0xffff; - printf("%-8s: %d.%ldC\n", label, val / 10, abs(val % 10)); - break; - case 1: /* prescaled voltage */ - if (val != 0xffff) - printf("%-8s: %d.%03dV\n", label, val / 1000, val % 1000); - break; - case 2: /* scaled based on ref volt and resolution */ - val *= 2500; - val /= 1 << 12; - - /* apply pre-scaler voltage divider */ - div = fdt_getprop(fdt, node, "gw,voltage-divider-ohms", &len); - if (div && (len == sizeof(uint32_t) * 2)) { - r[0] = fdt32_to_cpu(div[0]); - r[1] = fdt32_to_cpu(div[1]); - if (r[0] && r[1]) { - val *= (r[0] + r[1]); - val /= r[1]; - } - } - - /* adjust by offset */ - val += (offset / 1000); - - printf("%-8s: %d.%03dV\n", label, val / 1000, val % 1000); - break; - } - } - node = fdt_next_subnode(fdt, node); - } - - return 0; -} - -int gsc_info(int verbose) -{ - unsigned char buf[16]; - - if (gsc_i2c_read(GSC_SC_ADDR, 0, 1, buf, 16)) - return CMD_RET_FAILURE; - - printf("GSC: v%d", buf[GSC_SC_FWVER]); - printf(" 0x%04x", buf[GSC_SC_FWCRC] | buf[GSC_SC_FWCRC+1]<<8); - printf(" WDT:%sabled", (buf[GSC_SC_CTRL1] & (1<<GSC_SC_CTRL1_WDEN)) - ? "en" : "dis"); - if (buf[GSC_SC_STATUS] & (1 << GSC_SC_IRQ_WATCHDOG)) { - buf[GSC_SC_STATUS] &= ~(1 << GSC_SC_IRQ_WATCHDOG); - puts(" WDT_RESET"); - gsc_i2c_write(GSC_SC_ADDR, GSC_SC_STATUS, 1, - &buf[GSC_SC_STATUS], 1); - } - printf(" board temp at %dC", gsc_get_board_temp() / 10); - puts("\n"); - if (!verbose) - return CMD_RET_SUCCESS; - - gsc_hwmon(); - - return 0; -} - -/* - * The Gateworks System Controller implements a boot - * watchdog (always enabled) as a workaround for IMX6 boot related - * errata such as: - * ERR005768 - no fix scheduled - * ERR006282 - fixed in silicon r1.2 - * ERR007117 - fixed in silicon r1.3 - * ERR007220 - fixed in silicon r1.3 - * ERR007926 - no fix scheduled - * see http://cache.freescale.com/files/32bit/doc/errata/IMX6DQCE.pdf - * - * Disable the boot watchdog - */ -int gsc_boot_wd_disable(void) -{ - u8 reg; - - if (!gsc_i2c_read(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1)) { - reg |= (1 << GSC_SC_CTRL1_WDDIS); - if (!gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1)) - return 0; - } - puts("Error: could not disable GSC Watchdog\n"); - return 1; -} - -/* determine BOM revision from model */ -int get_bom_rev(const char *str) -{ - int rev_bom = 0; - int i; - - for (i = strlen(str) - 1; i > 0; i--) { - if (str[i] == '-') - break; - if (str[i] >= '1' && str[i] <= '9') { - rev_bom = str[i] - '0'; - break; - } - } - return rev_bom; -} - -/* determine PCB revision from model */ -char get_pcb_rev(const char *str) -{ - char rev_pcb = 'A'; - int i; - - for (i = strlen(str) - 1; i > 0; i--) { - if (str[i] == '-') - break; - if (str[i] >= 'A') { - rev_pcb = str[i]; - break; - } - } - return rev_pcb; -} - -/* - * get dt name based on model and detail level: - */ -const char *gsc_get_dtb_name(int level, char *buf, int sz) -{ - const char *model = (const char *)ventana_info.model; - const char *pre = is_mx6dq() ? "imx6q-" : "imx6dl-"; - int modelno, rev_pcb, rev_bom; - - /* a few board models are dt equivalents to other models */ - if (strncasecmp(model, "gw5906", 6) == 0) - model = "gw552x-d"; - else if (strncasecmp(model, "gw5908", 6) == 0) - model = "gw53xx-f"; - else if (strncasecmp(model, "gw5905", 6) == 0) - model = "gw5904-a"; - - modelno = ((model[2] - '0') * 1000) - + ((model[3] - '0') * 100) - + ((model[4] - '0') * 10) - + (model[5] - '0'); - rev_pcb = tolower(get_pcb_rev(model)); - rev_bom = get_bom_rev(model); - - /* compare model/rev/bom in order of most specific to least */ - snprintf(buf, sz, "%s%04d", pre, modelno); - switch (level) { - case 0: /* full model first (ie gw5400-a1) */ - if (rev_bom) { - snprintf(buf, sz, "%sgw%04d-%c%d", pre, modelno, rev_pcb, rev_bom); - break; - } - fallthrough; - case 1: /* don't care about bom rev (ie gw5400-a) */ - snprintf(buf, sz, "%sgw%04d-%c", pre, modelno, rev_pcb); - break; - case 2: /* don't care about the pcb rev (ie gw5400) */ - snprintf(buf, sz, "%sgw%04d", pre, modelno); - break; - case 3: /* look for generic model (ie gw540x) */ - snprintf(buf, sz, "%sgw%03dx", pre, modelno / 10); - break; - case 4: /* look for more generic model (ie gw54xx) */ - snprintf(buf, sz, "%sgw%02dxx", pre, modelno / 100); - break; - default: /* give up */ - return NULL; - } - - return buf; -} - -#if defined(CONFIG_CMD_GSC) && !defined(CONFIG_SPL_BUILD) -static int do_gsc_sleep(struct cmd_tbl *cmdtp, int flag, int argc, - char *const argv[]) -{ - unsigned char reg; - unsigned long secs = 0; - - if (argc < 2) - return CMD_RET_USAGE; - - secs = dectoul(argv[1], NULL); - printf("GSC Sleeping for %ld seconds\n", secs); - - reg = (secs >> 24) & 0xff; - if (gsc_i2c_write(GSC_SC_ADDR, 9, 1, &reg, 1)) - goto error; - reg = (secs >> 16) & 0xff; - if (gsc_i2c_write(GSC_SC_ADDR, 8, 1, &reg, 1)) - goto error; - reg = (secs >> 8) & 0xff; - if (gsc_i2c_write(GSC_SC_ADDR, 7, 1, &reg, 1)) - goto error; - reg = secs & 0xff; - if (gsc_i2c_write(GSC_SC_ADDR, 6, 1, &reg, 1)) - goto error; - if (gsc_i2c_read(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1)) - goto error; - reg |= (1 << 2); - if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1)) - goto error; - reg &= ~(1 << 2); - reg |= 0x3; - if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1)) - goto error; - - return CMD_RET_SUCCESS; - -error: - printf("i2c error\n"); - return CMD_RET_FAILURE; -} - -static int do_gsc_wd(struct cmd_tbl *cmdtp, int flag, int argc, - char *const argv[]) -{ - unsigned char reg; - - if (argc < 2) - return CMD_RET_USAGE; - - if (strcasecmp(argv[1], "enable") == 0) { - int timeout = 0; - - if (argc > 2) - timeout = dectoul(argv[2], NULL); - if (gsc_i2c_read(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1)) - return CMD_RET_FAILURE; - reg &= ~((1 << GSC_SC_CTRL1_WDEN) | (1 << GSC_SC_CTRL1_WDTIME)); - if (timeout == 60) - reg |= (1 << GSC_SC_CTRL1_WDTIME); - else - timeout = 30; - reg |= (1 << GSC_SC_CTRL1_WDEN); - if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1)) - return CMD_RET_FAILURE; - printf("GSC Watchdog enabled with timeout=%d seconds\n", - timeout); - } else if (strcasecmp(argv[1], "disable") == 0) { - if (gsc_i2c_read(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1)) - return CMD_RET_FAILURE; - reg &= ~((1 << GSC_SC_CTRL1_WDEN) | (1 << GSC_SC_CTRL1_WDTIME)); - if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1)) - return CMD_RET_FAILURE; - printf("GSC Watchdog disabled\n"); - } else { - return CMD_RET_USAGE; - } - return CMD_RET_SUCCESS; -} - -static int do_gsc(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[]) -{ - if (argc < 2) - return gsc_info(1); - - if (strcasecmp(argv[1], "wd") == 0) - return do_gsc_wd(cmdtp, flag, --argc, ++argv); - else if (strcasecmp(argv[1], "sleep") == 0) - return do_gsc_sleep(cmdtp, flag, --argc, ++argv); - - return CMD_RET_USAGE; -} - -U_BOOT_CMD( - gsc, 4, 1, do_gsc, "GSC configuration", - "[wd enable [30|60]]|[wd disable]|[sleep <secs>]\n" - ); - -#endif /* CONFIG_CMD_GSC */ -- 2.17.1

2 1

[PATCH] imx8m: fix reading of DDR4 MR registers
by Rasmus Villemoes 20 May '22

20 May '22

I was trying to employ lpddr4_mr_read() to something similar to what the imx8mm-cl-iot-gate board is doing for auto-detecting the RAM type. However, the version in drivers/ddr/imx/imx8m/ddrphy_utils.c differs from the private one used by that board in how it extracts the byte value, and I was only getting zeroes. Adding a bit of debug printf'ing gives me tmp = 0x00ffff00 tmp = 0x00070700 tmp = 0x00000000 tmp = 0x00101000 and indeed I was expecting a (combined) value of 0xff070010 (0xff being Manufacturer ID for Micron). I can't find any documentation that says how the values are supposed to be read, but clearly the iot-gate definition is the right one, both for its use case as well as my imx8mp-based board. So lift the private definition of lpddr4_mr_read() from the imx8mm-cl-iot-gate board code to ddrphy_utils.c, and add a declaration in the ddr.h header where e.g. get_trained_CDD() is already declared. This has only been compile-tested for the imx8mm-cl-iot-gate board (since I don't have the hardware), but since I've merely moved its definition of lpddr4_mr_read(), I'd be surprised if it changed anything for that board. Signed-off-by: Rasmus Villemoes <rasmus.villemoes(a)prevas.dk> --- arch/arm/include/asm/arch-imx8m/ddr.h | 1 + board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c | 27 --------------------- drivers/ddr/imx/imx8m/ddrphy_utils.c | 9 +++++-- 3 files changed, 8 insertions(+), 29 deletions(-) diff --git a/arch/arm/include/asm/arch-imx8m/ddr.h b/arch/arm/include/asm/arch-imx8m/ddr.h index 0f1e832c03..2ce8a8f2d4 100644 --- a/arch/arm/include/asm/arch-imx8m/ddr.h +++ b/arch/arm/include/asm/arch-imx8m/ddr.h @@ -723,6 +723,7 @@ void ddrphy_init_read_msg_block(enum fw_type type); void update_umctl2_rank_space_setting(unsigned int pstat_num); void get_trained_CDD(unsigned int fsp); +unsigned int lpddr4_mr_read(unsigned int mr_rank, unsigned int mr_addr); static inline void reg32_write(unsigned long addr, u32 val) { diff --git a/board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c b/board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c index 5b93491923..b230478b61 100644 --- a/board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c +++ b/board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c @@ -24,33 +24,6 @@ #include <linux/delay.h> -static unsigned int lpddr4_mr_read(unsigned int mr_rank, unsigned int mr_addr) -{ - unsigned int tmp; - - reg32_write(DRC_PERF_MON_MRR0_DAT(0), 0x1); - do { - tmp = reg32_read(DDRC_MRSTAT(0)); - } while (tmp & 0x1); - - reg32_write(DDRC_MRCTRL0(0), (mr_rank << 4) | 0x1); - reg32_write(DDRC_MRCTRL1(0), (mr_addr << 8)); - reg32setbit(DDRC_MRCTRL0(0), 31); - do { - tmp = reg32_read(DRC_PERF_MON_MRR0_DAT(0)); - } while ((tmp & 0x8) == 0); - tmp = reg32_read(DRC_PERF_MON_MRR1_DAT(0)); - reg32_write(DRC_PERF_MON_MRR0_DAT(0), 0x4); - while (tmp) { //try to find a significant byte in the word - if (tmp & 0xff) { - tmp &= 0xff; - break; - } - tmp >>= 8; - } - return tmp; -} - struct lpddr4_desc { char name[16]; unsigned int id; diff --git a/drivers/ddr/imx/imx8m/ddrphy_utils.c b/drivers/ddr/imx/imx8m/ddrphy_utils.c index a54449e5f1..975d553674 100644 --- a/drivers/ddr/imx/imx8m/ddrphy_utils.c +++ b/drivers/ddr/imx/imx8m/ddrphy_utils.c @@ -198,9 +198,14 @@ unsigned int lpddr4_mr_read(unsigned int mr_rank, unsigned int mr_addr) tmp = reg32_read(DRC_PERF_MON_MRR0_DAT(0)); } while ((tmp & 0x8) == 0); tmp = reg32_read(DRC_PERF_MON_MRR1_DAT(0)); - tmp = tmp & 0xff; reg32_write(DRC_PERF_MON_MRR0_DAT(0), 0x4); - + while (tmp) { //try to find a significant byte in the word + if (tmp & 0xff) { + tmp &= 0xff; + break; + } + tmp >>= 8; + } return tmp; } -- 2.31.1

5 4

[PATCH] board: gateworks: gw_ventana: add support for GPY111 PHY
by Tim Harvey 20 May '22

20 May '22

The MaxLinear GPY111 PHY is being used on some boards due to part availability. Add support for this PHY which requires a longer reset post-delay and RGMII delay configuration. Signed-off-by: Tim Harvey <tharvey(a)gateworks.com> --- arch/arm/dts/imx6qdl-gw51xx.dtsi | 2 +- arch/arm/dts/imx6qdl-gw52xx.dtsi | 2 +- arch/arm/dts/imx6qdl-gw53xx.dtsi | 2 +- arch/arm/dts/imx6qdl-gw54xx.dtsi | 2 +- arch/arm/dts/imx6qdl-gw560x.dtsi | 2 +- arch/arm/dts/imx6qdl-gw5903.dtsi | 2 +- arch/arm/dts/imx6qdl-gw5904.dtsi | 2 +- arch/arm/dts/imx6qdl-gw5907.dtsi | 2 +- arch/arm/dts/imx6qdl-gw5910.dtsi | 2 +- arch/arm/dts/imx6qdl-gw5912.dtsi | 2 +- arch/arm/dts/imx6qdl-gw5913.dtsi | 2 +- board/gateworks/gw_ventana/gw_ventana.c | 27 +++++++++++++++++++------ 12 files changed, 32 insertions(+), 17 deletions(-) diff --git a/arch/arm/dts/imx6qdl-gw51xx.dtsi b/arch/arm/dts/imx6qdl-gw51xx.dtsi index 812acf7ab824..139ffe012dc3 100644 --- a/arch/arm/dts/imx6qdl-gw51xx.dtsi +++ b/arch/arm/dts/imx6qdl-gw51xx.dtsi @@ -130,7 +130,7 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; phy-reset-duration = <10>; - phy-reset-post-delay = <100>; + phy-reset-post-delay = <300>; status = "okay"; }; diff --git a/arch/arm/dts/imx6qdl-gw52xx.dtsi b/arch/arm/dts/imx6qdl-gw52xx.dtsi index 81a9ce38b9b1..1b5c836ff39b 100644 --- a/arch/arm/dts/imx6qdl-gw52xx.dtsi +++ b/arch/arm/dts/imx6qdl-gw52xx.dtsi @@ -196,7 +196,7 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; phy-reset-duration = <10>; - phy-reset-post-delay = <100>; + phy-reset-post-delay = <300>; status = "okay"; }; diff --git a/arch/arm/dts/imx6qdl-gw53xx.dtsi b/arch/arm/dts/imx6qdl-gw53xx.dtsi index 77ac103c2d9f..e5e9e0c0589a 100644 --- a/arch/arm/dts/imx6qdl-gw53xx.dtsi +++ b/arch/arm/dts/imx6qdl-gw53xx.dtsi @@ -190,7 +190,7 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; phy-reset-duration = <10>; - phy-reset-post-delay = <100>; + phy-reset-post-delay = <300>; status = "okay"; }; diff --git a/arch/arm/dts/imx6qdl-gw54xx.dtsi b/arch/arm/dts/imx6qdl-gw54xx.dtsi index 98c81e9c9b5b..2f41f0921424 100644 --- a/arch/arm/dts/imx6qdl-gw54xx.dtsi +++ b/arch/arm/dts/imx6qdl-gw54xx.dtsi @@ -227,7 +227,7 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; phy-reset-duration = <10>; - phy-reset-post-delay = <100>; + phy-reset-post-delay = <300>; status = "okay"; }; diff --git a/arch/arm/dts/imx6qdl-gw560x.dtsi b/arch/arm/dts/imx6qdl-gw560x.dtsi index 1e95267c974f..6586d877204c 100644 --- a/arch/arm/dts/imx6qdl-gw560x.dtsi +++ b/arch/arm/dts/imx6qdl-gw560x.dtsi @@ -281,7 +281,7 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; phy-reset-duration = <10>; - phy-reset-post-delay = <100>; + phy-reset-post-delay = <300>; status = "okay"; }; diff --git a/arch/arm/dts/imx6qdl-gw5903.dtsi b/arch/arm/dts/imx6qdl-gw5903.dtsi index 6ebf6aef2f7d..1df3faba4167 100644 --- a/arch/arm/dts/imx6qdl-gw5903.dtsi +++ b/arch/arm/dts/imx6qdl-gw5903.dtsi @@ -225,7 +225,7 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; phy-reset-duration = <10>; - phy-reset-post-delay = <100>; + phy-reset-post-delay = <300>; status = "okay"; }; diff --git a/arch/arm/dts/imx6qdl-gw5904.dtsi b/arch/arm/dts/imx6qdl-gw5904.dtsi index 286c7a9924c2..381f605cc0d5 100644 --- a/arch/arm/dts/imx6qdl-gw5904.dtsi +++ b/arch/arm/dts/imx6qdl-gw5904.dtsi @@ -203,7 +203,7 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; phy-reset-duration = <10>; - phy-reset-post-delay = <100>; + phy-reset-post-delay = <300>; status = "okay"; fixed-link { diff --git a/arch/arm/dts/imx6qdl-gw5907.dtsi b/arch/arm/dts/imx6qdl-gw5907.dtsi index a36b6e7048c7..68585f84d13c 100644 --- a/arch/arm/dts/imx6qdl-gw5907.dtsi +++ b/arch/arm/dts/imx6qdl-gw5907.dtsi @@ -132,7 +132,7 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; phy-reset-duration = <10>; - phy-reset-post-delay = <100>; + phy-reset-post-delay = <300>; status = "okay"; }; diff --git a/arch/arm/dts/imx6qdl-gw5910.dtsi b/arch/arm/dts/imx6qdl-gw5910.dtsi index 446c1043a768..594468dcba8e 100644 --- a/arch/arm/dts/imx6qdl-gw5910.dtsi +++ b/arch/arm/dts/imx6qdl-gw5910.dtsi @@ -148,7 +148,7 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; phy-reset-duration = <10>; - phy-reset-post-delay = <100>; + phy-reset-post-delay = <300>; status = "okay"; }; diff --git a/arch/arm/dts/imx6qdl-gw5912.dtsi b/arch/arm/dts/imx6qdl-gw5912.dtsi index 8fd8fdb5147c..f51ec3d62ce0 100644 --- a/arch/arm/dts/imx6qdl-gw5912.dtsi +++ b/arch/arm/dts/imx6qdl-gw5912.dtsi @@ -144,7 +144,7 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; phy-reset-duration = <10>; - phy-reset-post-delay = <100>; + phy-reset-post-delay = <300>; status = "okay"; }; diff --git a/arch/arm/dts/imx6qdl-gw5913.dtsi b/arch/arm/dts/imx6qdl-gw5913.dtsi index c2c1c2b160d4..44d347f04eb6 100644 --- a/arch/arm/dts/imx6qdl-gw5913.dtsi +++ b/arch/arm/dts/imx6qdl-gw5913.dtsi @@ -123,7 +123,7 @@ phy-mode = "rgmii-id"; phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; phy-reset-duration = <10>; - phy-reset-post-delay = <100>; + phy-reset-post-delay = <300>; status = "okay"; }; diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c index c06630a66b66..99f52b9953e2 100644 --- a/board/gateworks/gw_ventana/gw_ventana.c +++ b/board/gateworks/gw_ventana/gw_ventana.c @@ -32,9 +32,10 @@ DECLARE_GLOBAL_DATA_PTR; int board_phy_config(struct phy_device *phydev) { unsigned short val; + ofnode node; - /* Marvel 88E1510 */ - if (phydev->phy_id == 0x1410dd1) { + switch (phydev->phy_id) { + case 0x1410dd1: puts("MV88E1510"); /* * Page 3, Register 16: LED[2:0] Function Control Register @@ -47,10 +48,8 @@ int board_phy_config(struct phy_device *phydev) val |= 0x0017; phy_write(phydev, MDIO_DEVAD_NONE, 16, val); phy_write(phydev, MDIO_DEVAD_NONE, 22, 0); - } - - /* TI DP83867 */ - else if (phydev->phy_id == 0x2000a231) { + break; + case 0x2000a231: puts("TIDP83867 "); /* LED configuration */ val = 0; @@ -66,6 +65,22 @@ int board_phy_config(struct phy_device *phydev) val &= ~0x1f00; val |= 0x0b00; /* chD tx clock*/ phy_write(phydev, MDIO_DEVAD_NONE, 14, val); + break; + case 0xd565a401: + puts("GPY111 "); + node = phy_get_ofnode(phydev); + if (ofnode_valid(node)) { + u32 rx_delay, tx_delay; + + rx_delay = ofnode_read_u32_default(node, "rx-internal-delay-ps", 2000); + tx_delay = ofnode_read_u32_default(node, "tx-internal-delay-ps", 2000); + val = phy_read(phydev, MDIO_DEVAD_NONE, 0x17); + val &= ~((0x7 << 12) | (0x7 << 8)); + val |= (rx_delay / 500) << 12; + val |= (tx_delay / 500) << 8; + phy_write(phydev, MDIO_DEVAD_NONE, 0x17, val); + } + break; } if (phydev->drv->config) -- 2.17.1

2 1

[PATCH v2] usb: dwc3: add a SPL_USB_DWC3_GENERIC option for the dwc3 driver
by Angus Ainslie 20 May '22

20 May '22

Suppress warnings when building the SPL without USB_DWC3_GENERIC Signed-off-by: Angus Ainslie <angus(a)akkea.ca> --- Changes since v1: Updated Kconfig depends drivers/usb/dwc3/Kconfig | 7 +++++++ drivers/usb/dwc3/Makefile | 2 +- 2 files changed, 8 insertions(+), 1 deletion(-) diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig index 62aa65bf0c..f010291d02 100644 --- a/drivers/usb/dwc3/Kconfig +++ b/drivers/usb/dwc3/Kconfig @@ -30,6 +30,13 @@ config USB_DWC3_GENERIC Select this for Xilinx ZynqMP and similar Platforms. This wrapper supports Host and Peripheral operation modes. +config SPL_USB_DWC3_GENERIC + bool "Generic implementation of a DWC3 wrapper (aka dwc3 glue) for the SPL" + depends on SPL_DM_USB && USB_DWC3 && SPL_MISC + help + Select this for Xilinx ZynqMP and similar Platforms. + This wrapper supports Host and Peripheral operation modes. + config USB_DWC3_MESON_G12A bool "Amlogic Meson G12A USB wrapper" depends on DM_USB && USB_DWC3 && ARCH_MESON diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile index 0dd1ba87cd..97b4f7191c 100644 --- a/drivers/usb/dwc3/Makefile +++ b/drivers/usb/dwc3/Makefile @@ -9,7 +9,7 @@ obj-$(CONFIG_USB_DWC3_GADGET) += gadget.o ep0.o obj-$(CONFIG_USB_DWC3_OMAP) += dwc3-omap.o obj-$(CONFIG_USB_DWC3_MESON_G12A) += dwc3-meson-g12a.o obj-$(CONFIG_USB_DWC3_MESON_GXL) += dwc3-meson-gxl.o -obj-$(CONFIG_USB_DWC3_GENERIC) += dwc3-generic.o +obj-$(CONFIG_$(SPL_)USB_DWC3_GENERIC) += dwc3-generic.o obj-$(CONFIG_USB_DWC3_UNIPHIER) += dwc3-uniphier.o obj-$(CONFIG_USB_DWC3_LAYERSCAPE) += dwc3-layerscape.o obj-$(CONFIG_USB_DWC3_PHY_OMAP) += ti_usb_phy.o -- 2.34.1

3 4

[PATCH v2 1/2] pmic: pca9450: Add upstream regulators subnode match
by Marek Vasut 20 May '22

20 May '22

The upstream DT regulators node subnodes are named BUCKn and LDOn, the downstream DT regulators node subnodes are named buckn and ldon, add the upstream match. Reviewed-by: Fabio Estevam <festevam(a)denx.de> Signed-off-by: Marek Vasut <marex(a)denx.de> Cc: Fabio Estevam <festevam(a)denx.de> Cc: Peng Fan <peng.fan(a)nxp.com> Cc: Stefano Babic <sbabic(a)denx.de> --- V2: Add RB by Fabio --- drivers/power/pmic/pca9450.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/power/pmic/pca9450.c b/drivers/power/pmic/pca9450.c index 2394b196c56..26c876c9c45 100644 --- a/drivers/power/pmic/pca9450.c +++ b/drivers/power/pmic/pca9450.c @@ -19,8 +19,10 @@ DECLARE_GLOBAL_DATA_PTR; static const struct pmic_child_info pmic_children_info[] = { /* buck */ { .prefix = "b", .driver = PCA9450_REGULATOR_DRIVER}, + { .prefix = "B", .driver = PCA9450_REGULATOR_DRIVER}, /* ldo */ { .prefix = "l", .driver = PCA9450_REGULATOR_DRIVER}, + { .prefix = "L", .driver = PCA9450_REGULATOR_DRIVER}, { }, }; -- 2.35.1

3 7

[U-Boot] [PATCH 1/2] rockchip: rk3399: fix force power on reset
by Vasily Khoruzhick 19 May '22

19 May '22

Currently code doesn't even compile since it uses wrong define for ifdef. Fix that and also add missing include Fixes: 07586ee4322a ("rockchip: rk3399: Support common spl_board_init") Signed-off-by: Vasily Khoruzhick <anarsoul(a)gmail.com> --- arch/arm/mach-rockchip/rk3399/rk3399.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-rockchip/rk3399/rk3399.c b/arch/arm/mach-rockchip/rk3399/rk3399.c index 863024d071..eeb99dd11b 100644 --- a/arch/arm/mach-rockchip/rk3399/rk3399.c +++ b/arch/arm/mach-rockchip/rk3399/rk3399.c @@ -11,6 +11,7 @@ #include <asm/io.h> #include <asm/arch-rockchip/bootrom.h> #include <asm/arch-rockchip/clock.h> +#include <asm/arch-rockchip/cru_rk3399.h> #include <asm/arch-rockchip/gpio.h> #include <asm/arch-rockchip/grf_rk3399.h> #include <asm/arch-rockchip/hardware.h> @@ -213,7 +214,7 @@ void spl_perform_fixups(struct spl_image_info *spl_image) "u-boot,spl-boot-device", boot_ofpath); } -#if defined(SPL_GPIO_SUPPORT) +#if defined(CONFIG_SPL_GPIO_SUPPORT) static void rk3399_force_power_on_reset(void) { ofnode node; @@ -239,7 +240,7 @@ static void rk3399_force_power_on_reset(void) void spl_board_init(void) { -#if defined(SPL_GPIO_SUPPORT) +#if defined(CONFIG_SPL_GPIO_SUPPORT) struct rk3399_cru *cru = rockchip_get_cru(); /* -- 2.24.0

5 23

[RFC PATCH 0/8] Build Rockchip final images using binman
by Andrew Abbott 19 May '22

19 May '22

My original goal was to produce SPI images for Rockchip platforms (specifically for me, ROCKPro64, and in the future ROCK64). Looking into it, it seemed nicer to just switch the SD/MMC image generation over to binman as well in the process. This is my attempt to move Rockchip final full image generation to binman, adding the option to make full SPI images as well. I'm sending this as RFC patches because I'm not sure whether this is the ideal way to do this, whether this is even something we'd even want to do, and exactly what I might be breaking by doing this. Other questions: - I noticed that ATF generation for ARM64 Rockchip is done via a Python script instead of binman. I don't currently know how to change that over to binman, but is that something worth pursuing as part of this? Please give me your feedback! Andrew Abbott (8): binman: mkimage: Support ':'-separated inputs rockchip: Add binman definitions for final images soc: rockchip: Include common U-Boot dtsi file board: rockchip: Move SPI U-Boot offset to config rockchip: Remove obsolete Makefile targets rockchip: Enable binman for ARM64 doc: rockchip: Update for new binman image generation board: rockpro64: Enable building SPI image Kconfig | 4 +- Makefile | 31 +--------- arch/arm/Kconfig | 2 +- arch/arm/dts/rk3308-u-boot.dtsi | 2 + arch/arm/dts/rk3328-u-boot.dtsi | 2 + arch/arm/dts/rk3368-lion-haikou-u-boot.dtsi | 1 - arch/arm/dts/rk3368-u-boot.dtsi | 1 + arch/arm/dts/rk3399-pinebook-pro-u-boot.dtsi | 4 -- arch/arm/dts/rk3399-puma-haikou-u-boot.dtsi | 1 - arch/arm/dts/rk3399-roc-pc-u-boot.dtsi | 4 -- arch/arm/dts/rk3399-rockpro64-u-boot.dtsi | 4 -- arch/arm/dts/rk3568-u-boot.dtsi | 2 + arch/arm/dts/rockchip-u-boot.dtsi | 59 ++++++++++++++++++-- arch/arm/mach-rockchip/Kconfig | 7 +-- arch/arm/mach-rockchip/rk3399/Kconfig | 1 + configs/lion-rk3368_defconfig | 1 + configs/pinebook-pro-rk3399_defconfig | 1 + configs/puma-rk3399_defconfig | 2 +- configs/roc-pc-rk3399_defconfig | 1 + configs/rockpro64-rk3399_defconfig | 1 + doc/board/rockchip/rockchip.rst | 34 ++++------- tools/binman/etype/mkimage.py | 33 +++++++---- 22 files changed, 107 insertions(+), 91 deletions(-) -- 2.35.3

3 11

[PATCH v2] cmd: bootefi: restore ability to boot arbitrary blob
by kevans＠FreeBSD.org 19 May '22

19 May '22

From: Kyle Evans <kevans(a)FreeBSD.org> Up until commit 5f59518a7b1ae ("efi_loader: setting boot device"), we could boot an arbitrary blob with bootefi. Indeed, efi_run_image() even has a special case for missing device paths indicating a payload that was directly loaded via JTAG, for example. Restore the ability to inject a UEFI payload into memory and `bootefi` it. If the address passed isn't the last PE-COFF loaded, then we'll wipe out the pre-existing DP/Image information and let efi_run_image() synthesize a memory device path. An image size is required if we're booting an arbitrary payload, and the FDT argument has been changed to accept `-`. The size could be deduced from the image header, but it's required anyways as an explicit acknowledgment that one's trying to boot an arbitrary payload rather than accidentally using the wrong address in the single-addr form. If the image address matches the last loaded PE_COFF, it is an error to pass the incorrect size (but the size may be omitted). Signed-off-by: Kyle Evans <kevans(a)FreeBSD.org> --- Changes since v1: - Specifying an address that isn't the last-known without a size produces the same error as in the past ("No UEFI binary known at ...") - Specifying a size with the last known address that doesn't match the last recorded size will get: Size does not match known UEFI binary at %s cmd/bootefi.c | 42 ++++++++++++++++++++++++++++++++++-------- 1 file changed, 34 insertions(+), 8 deletions(-) diff --git a/cmd/bootefi.c b/cmd/bootefi.c index 53d9f0e0dc..0d3aecb2a1 100644 --- a/cmd/bootefi.c +++ b/cmd/bootefi.c @@ -425,7 +425,7 @@ static int do_efibootmgr(void) * @image_opt: string of image start address * Return: status code */ -static int do_bootefi_image(const char *image_opt) +static int do_bootefi_image(const char *image_opt, const char *size_opt) { void *image_buf; unsigned long addr, size; @@ -444,13 +444,35 @@ static int do_bootefi_image(const char *image_opt) if (!addr) return CMD_RET_USAGE; + size = 0; + if (size_opt) { + size = strtoul(size_opt, NULL, 16); + /* Check that a numeric value was passed */ + if (!size) + return CMD_RET_USAGE; + } + image_buf = map_sysmem(addr, 0); if (image_buf != image_addr) { - log_err("No UEFI binary known at %s\n", image_opt); - return CMD_RET_FAILURE; + /* Fake device path -- we must have a size. */ + + if (size == 0) { + printf("No UEFI binary known at %s\n", image_opt); + return CMD_RET_FAILURE; + } + + if (image_addr) + efi_clear_bootdev(); + } else { + if (size != 0 && size != image_size) { + printf("Size does not match known UEFI binary at %s\n", + image_opt); + return CMD_RET_FAILURE; + } + + size = image_size; } - size = image_size; } ret = efi_run_image(image_buf, size); @@ -654,7 +676,7 @@ static int do_bootefi(struct cmd_tbl *cmdtp, int flag, int argc, return CMD_RET_FAILURE; } - if (argc > 2) { + if (argc > 2 && strcmp(argv[2], "-") != 0) { uintptr_t fdt_addr; fdt_addr = hextoul(argv[2], NULL); @@ -677,15 +699,19 @@ static int do_bootefi(struct cmd_tbl *cmdtp, int flag, int argc, return do_efi_selftest(); #endif - return do_bootefi_image(argv[1]); + return do_bootefi_image(argv[1], argc > 3 ? argv[3] : NULL); } #ifdef CONFIG_SYS_LONGHELP static char bootefi_help_text[] = - "<image address> [fdt address]\n" + "<image address> [fdt address [image size]]\n" " - boot EFI payload stored at address <image address>.\n" " If specified, the device tree located at <fdt address> gets\n" " exposed as EFI configuration table.\n" + " The image size is required if this is not a preloaded image, but\n" + " it must be omitted if the image was preloaded.\n" + " The <fdt address> parameter accepts '-' to indicate FDT already\n" + " installed or pre-specified in fdt_addr or fdtcontroladdr.\n" #ifdef CONFIG_CMD_BOOTEFI_HELLO "bootefi hello\n" " - boot a sample Hello World application stored within U-Boot\n" @@ -707,7 +733,7 @@ static char bootefi_help_text[] = #endif U_BOOT_CMD( - bootefi, 3, 0, do_bootefi, + bootefi, 4, 0, do_bootefi, "Boots an EFI payload from memory", bootefi_help_text ); -- 2.33.0

4 4

[PATCH v14 0/2] add TCP and HTTP for downloading images
by Ying-Chun Liu 18 May '22

18 May '22

From: "Ying-Chun Liu (PaulLiu)" <paul.liu(a)linaro.org> This patch is a refresh from previous patches made by Duncan Hare <DuncanCHare(a)yahoo.com>. I've contacted him and continue to work on this patch. This patch introduce a TCP stack with SACK. And a simple wget command to download images from http server. v13: Fix some issues which is reviewed by Christian v14: Add options to enable/disable SACK. Ying-Chun Liu (PaulLiu) (2): net: Add TCP protocol net: Add wget application cmd/Kconfig | 7 + cmd/net.c | 13 + include/net.h | 10 +- include/net/tcp.h | 222 ++++++++++++++ include/net/wget.h | 19 ++ net/Kconfig | 12 + net/Makefile | 2 + net/net.c | 36 +++ net/tcp.c | 709 +++++++++++++++++++++++++++++++++++++++++++++ net/wget.c | 436 ++++++++++++++++++++++++++++ 10 files changed, 1464 insertions(+), 2 deletions(-) create mode 100644 include/net/tcp.h create mode 100644 include/net/wget.h create mode 100644 net/tcp.c create mode 100644 net/wget.c -- 2.35.1

4 7

[PATCH 1/4] Rename CONFIG_EHCI_IS_TDI to CONFIG_USB_EHCI_IS_TDI
by Marek Behún 18 May '22

18 May '22

From: Marek Behún <marek.behun(a)nic.cz> In preparation for moving this option to Kconfig, rename it to be consistent with other USB EHCI Kconfig options. Signed-off-by: Marek Behún <marek.behun(a)nic.cz> --- arch/arm/mach-kirkwood/include/mach/config.h | 2 +- drivers/usb/host/ehci-hcd.c | 2 +- include/configs/clearfog.h | 2 +- include/configs/controlcenterdc.h | 2 +- include/configs/crs3xx-98dx3236.h | 2 +- include/configs/db-88f6720.h | 2 +- include/configs/db-88f6820-amc.h | 2 +- include/configs/db-88f6820-gp.h | 2 +- include/configs/db-mv784mp-gp.h | 2 +- include/configs/db-xc3-24g4xg.h | 2 +- include/configs/ds414.h | 2 +- include/configs/helios4.h | 2 +- include/configs/mxs.h | 2 +- include/configs/nas220.h | 2 +- include/configs/tegra114-common.h | 2 +- include/configs/tegra124-common.h | 2 +- include/configs/tegra20-common.h | 2 +- include/configs/tegra210-common.h | 2 +- include/configs/tegra30-common.h | 2 +- include/configs/theadorable.h | 2 +- include/configs/tplink_wdr4300.h | 2 +- include/configs/turris_omnia.h | 2 +- include/configs/x530.h | 2 +- include/configs/zynq-common.h | 2 +- scripts/config_whitelist.txt | 2 +- 25 files changed, 25 insertions(+), 25 deletions(-) diff --git a/arch/arm/mach-kirkwood/include/mach/config.h b/arch/arm/mach-kirkwood/include/mach/config.h index 9002e26d75..f262d70b14 100644 --- a/arch/arm/mach-kirkwood/include/mach/config.h +++ b/arch/arm/mach-kirkwood/include/mach/config.h @@ -66,7 +66,7 @@ * USB/EHCI */ #ifdef CONFIG_CMD_USB -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI #endif /* CONFIG_CMD_USB */ /* diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index ba75c27d04..e6355263cb 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -108,7 +108,7 @@ static struct descriptor { }, }; -#if defined(CONFIG_EHCI_IS_TDI) +#if defined(CONFIG_USB_EHCI_IS_TDI) #define ehci_is_TDI() (1) #else #define ehci_is_TDI() (0) diff --git a/include/configs/clearfog.h b/include/configs/clearfog.h index 705217067b..a12e1582d6 100644 --- a/include/configs/clearfog.h +++ b/include/configs/clearfog.h @@ -19,7 +19,7 @@ */ /* USB/EHCI configuration */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI #define CONFIG_ENV_MIN_ENTRIES 128 diff --git a/include/configs/controlcenterdc.h b/include/configs/controlcenterdc.h index efd04c6fb8..12e9b8d06d 100644 --- a/include/configs/controlcenterdc.h +++ b/include/configs/controlcenterdc.h @@ -28,7 +28,7 @@ CONFIG_SYS_SCSI_MAX_LUN) /* USB/EHCI configuration */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI /* Environment in SPI NOR flash */ diff --git a/include/configs/crs3xx-98dx3236.h b/include/configs/crs3xx-98dx3236.h index 3feaa60eda..5300467a76 100644 --- a/include/configs/crs3xx-98dx3236.h +++ b/include/configs/crs3xx-98dx3236.h @@ -14,7 +14,7 @@ #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg /* USB/EHCI configuration */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI /* Environment in SPI NOR flash */ diff --git a/include/configs/db-88f6720.h b/include/configs/db-88f6720.h index 95f5cf0056..76c02f6656 100644 --- a/include/configs/db-88f6720.h +++ b/include/configs/db-88f6720.h @@ -20,7 +20,7 @@ #define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE /* USB/EHCI configuration */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI #define CONFIG_USB_MAX_CONTROLLER_COUNT 3 /* Environment in SPI NOR flash */ diff --git a/include/configs/db-88f6820-amc.h b/include/configs/db-88f6820-amc.h index 41216b8b4f..c5f0a1d2e0 100644 --- a/include/configs/db-88f6820-amc.h +++ b/include/configs/db-88f6820-amc.h @@ -11,7 +11,7 @@ */ /* USB/EHCI configuration */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI /* Environment in SPI NOR flash */ diff --git a/include/configs/db-88f6820-gp.h b/include/configs/db-88f6820-gp.h index 6bae063ae4..ecda30bab5 100644 --- a/include/configs/db-88f6820-gp.h +++ b/include/configs/db-88f6820-gp.h @@ -23,7 +23,7 @@ CONFIG_SYS_SCSI_MAX_LUN) /* USB/EHCI configuration */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI /* Environment in SPI NOR flash */ diff --git a/include/configs/db-mv784mp-gp.h b/include/configs/db-mv784mp-gp.h index 48471993b8..defe480613 100644 --- a/include/configs/db-mv784mp-gp.h +++ b/include/configs/db-mv784mp-gp.h @@ -21,7 +21,7 @@ #define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE /* USB/EHCI configuration */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI #define CONFIG_USB_MAX_CONTROLLER_COUNT 3 /* Environment in SPI NOR flash */ diff --git a/include/configs/db-xc3-24g4xg.h b/include/configs/db-xc3-24g4xg.h index 2c543fe12a..206afae590 100644 --- a/include/configs/db-xc3-24g4xg.h +++ b/include/configs/db-xc3-24g4xg.h @@ -13,7 +13,7 @@ #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg /* USB/EHCI configuration */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI /* Environment in SPI NOR flash */ diff --git a/include/configs/ds414.h b/include/configs/ds414.h index 58ecc5f699..85abed5d3b 100644 --- a/include/configs/ds414.h +++ b/include/configs/ds414.h @@ -25,7 +25,7 @@ #endif /* USB/EHCI/XHCI configuration */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI /* * mv-common.h should be defined after CMD configs since it used them diff --git a/include/configs/helios4.h b/include/configs/helios4.h index b5814ed55c..7ed70602d1 100644 --- a/include/configs/helios4.h +++ b/include/configs/helios4.h @@ -19,7 +19,7 @@ */ /* USB/EHCI configuration */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI #define CONFIG_ENV_MIN_ENTRIES 128 diff --git a/include/configs/mxs.h b/include/configs/mxs.h index b5c525dc78..330ac42402 100644 --- a/include/configs/mxs.h +++ b/include/configs/mxs.h @@ -129,7 +129,7 @@ /* USB */ #ifdef CONFIG_CMD_USB #define CONFIG_USB_EHCI_MXS -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI #endif #endif /* __CONFIGS_MXS_H__ */ diff --git a/include/configs/nas220.h b/include/configs/nas220.h index 16bbc9b049..f071ee6e1c 100644 --- a/include/configs/nas220.h +++ b/include/configs/nas220.h @@ -65,7 +65,7 @@ */ #ifdef CONFIG_CMD_USB #define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI #endif /* CONFIG_CMD_USB */ /* diff --git a/include/configs/tegra114-common.h b/include/configs/tegra114-common.h index f714c52bb5..06b687d556 100644 --- a/include/configs/tegra114-common.h +++ b/include/configs/tegra114-common.h @@ -58,7 +58,7 @@ #define CONFIG_SPL_STACK 0x800ffffc /* For USB EHCI controller */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10 #endif /* _TEGRA114_COMMON_H_ */ diff --git a/include/configs/tegra124-common.h b/include/configs/tegra124-common.h index 4a92954c9b..de78ac9924 100644 --- a/include/configs/tegra124-common.h +++ b/include/configs/tegra124-common.h @@ -60,7 +60,7 @@ #define CONFIG_SPL_STACK 0x800ffffc /* For USB EHCI controller */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10 /* GPU needs setup */ diff --git a/include/configs/tegra20-common.h b/include/configs/tegra20-common.h index 19934a4cf0..d2bed64ccd 100644 --- a/include/configs/tegra20-common.h +++ b/include/configs/tegra20-common.h @@ -78,7 +78,7 @@ * packets depending on the buffer address and size. */ #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10 -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI #define CONFIG_SYS_NAND_SELF_INIT diff --git a/include/configs/tegra210-common.h b/include/configs/tegra210-common.h index b9e04147be..6c58ccc3d5 100644 --- a/include/configs/tegra210-common.h +++ b/include/configs/tegra210-common.h @@ -47,7 +47,7 @@ "ramdisk_addr_r=0x83200000\0" /* For USB EHCI controller */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10 /* GPU needs setup */ diff --git a/include/configs/tegra30-common.h b/include/configs/tegra30-common.h index 0ee13a226d..56b2671e43 100644 --- a/include/configs/tegra30-common.h +++ b/include/configs/tegra30-common.h @@ -55,7 +55,7 @@ #define CONFIG_SPL_STACK 0x800ffffc /* For USB EHCI controller */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10 #endif /* _TEGRA30_COMMON_H_ */ diff --git a/include/configs/theadorable.h b/include/configs/theadorable.h index 64b7f25092..073855592b 100644 --- a/include/configs/theadorable.h +++ b/include/configs/theadorable.h @@ -29,7 +29,7 @@ #define CONFIG_I2C_MVTWSI_BASE1 MVEBU_TWSI1_BASE /* USB/EHCI configuration */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI #define CONFIG_USB_MAX_CONTROLLER_COUNT 3 /* Environment in SPI NOR flash */ diff --git a/include/configs/tplink_wdr4300.h b/include/configs/tplink_wdr4300.h index f9a0b7d1aa..ede94e95f7 100644 --- a/include/configs/tplink_wdr4300.h +++ b/include/configs/tplink_wdr4300.h @@ -41,7 +41,7 @@ /* USB, USB storage, USB ethernet */ #define CONFIG_EHCI_MMIO_BIG_ENDIAN #define CONFIG_EHCI_DESC_BIG_ENDIAN -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI /* * Diagnostics diff --git a/include/configs/turris_omnia.h b/include/configs/turris_omnia.h index 8646633ea4..4d8a7c37de 100644 --- a/include/configs/turris_omnia.h +++ b/include/configs/turris_omnia.h @@ -18,7 +18,7 @@ */ /* USB/EHCI configuration */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI /* Environment in SPI NOR flash */ diff --git a/include/configs/x530.h b/include/configs/x530.h index d6aec6d7f2..23b1121460 100644 --- a/include/configs/x530.h +++ b/include/configs/x530.h @@ -46,7 +46,7 @@ /* Additional FS support/configuration */ /* USB/EHCI configuration */ -#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_IS_TDI /* Environment in SPI NOR flash */ diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h index 0c87f19ac3..f3c8512641 100644 --- a/include/configs/zynq-common.h +++ b/include/configs/zynq-common.h @@ -55,7 +55,7 @@ #endif #ifdef CONFIG_USB_EHCI_ZYNQ -# define CONFIG_EHCI_IS_TDI +# define CONFIG_USB_EHCI_IS_TDI # define DFU_DEFAULT_POLL_TIMEOUT 300 # define CONFIG_THOR_RESET_OFF diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 02d86d79cf..682f597f37 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -246,7 +246,6 @@ CONFIG_EDB93XX_SDCS3 CONFIG_EFLASH_PROTSECTORS CONFIG_EHCI_DESC_BIG_ENDIAN CONFIG_EHCI_HCD_INIT_AFTER_RESET -CONFIG_EHCI_IS_TDI CONFIG_EHCI_MMIO_BIG_ENDIAN CONFIG_EHCI_MXS_PORT0 CONFIG_EHCI_MXS_PORT1 @@ -3036,6 +3035,7 @@ CONFIG_USB_EHCI_BASE CONFIG_USB_EHCI_BASE_LIST CONFIG_USB_EHCI_EXYNOS CONFIG_USB_EHCI_FARADAY +CONFIG_USB_EHCI_IS_TDI CONFIG_USB_EHCI_KIRKWOOD CONFIG_USB_EHCI_MXS CONFIG_USB_EHCI_TXFIFO_THRESH -- 2.32.0

3 9