March 2019 - U-Boot

[U-Boot] [PATCH] common: spl_fit: Allow firmware image if no loadables
by Abel Vesa 07 Mar '19

07 Mar '19

If CONFIG_SPL_OS_BOOT and FIT_IMAGE_TINY are enabled, the os will not be set to anything and therefore will remain as IH_OS_INVALID. What's needed here is to have IH_OS_U_BOOT as default. And since using the mkimage oneline command (that is, no its file), the loadables can't be specified, so we allow firmware as a fallback. Signed-off-by: Abel Vesa <abel.vesa(a)nxp.com> --- common/spl/spl_fit.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/common/spl/spl_fit.c b/common/spl/spl_fit.c index db43626..d5aa792 100644 --- a/common/spl/spl_fit.c +++ b/common/spl/spl_fit.c @@ -478,11 +478,14 @@ int spl_load_simple_fit(struct spl_image_info *spl_image, /* Now check if there are more images for us to load */ for (; ; index++) { - uint8_t os_type = IH_OS_INVALID; + uint8_t os_type = IH_OS_U_BOOT; node = spl_fit_get_image_node(fit, images, "loadables", index); if (node < 0) - break; + node = spl_fit_get_image_node(fit, images, + "firmware", index); + if (node < 0) + break; ret = spl_load_fit_image(info, sector, fit, base_offset, node, &image_info); -- 2.7.4

2 1

[U-Boot] [U-Boot, V3, PATCH 3/3] mips: fix erros on registers macros of pll-ddr-config1-nfrac for QCA956X
by rosysong＠rosinson.com 07 Mar '19

07 Mar '19

From: Rosy Song <rosysong(a)rosinson.com> See details in chapter 8.6.2 and 8.6.4 (page 140-141) of qca9563 datasheet, NFRAC[17:0] So the mask of [17:5] is 0x1fff not 0x3fff. Signed-off-by: Rosy Song <rosysong(a)rosinson.com> Changes for v2-v3: - add more information for this commit --- arch/mips/mach-ath79/include/mach/ar71xx_regs.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/mips/mach-ath79/include/mach/ar71xx_regs.h b/arch/mips/mach-ath79/include/mach/ar71xx_regs.h index 7cd16b8d81..5888f6eb28 100644 --- a/arch/mips/mach-ath79/include/mach/ar71xx_regs.h +++ b/arch/mips/mach-ath79/include/mach/ar71xx_regs.h @@ -554,7 +554,7 @@ #define QCA956X_PLL_CPU_CONFIG1_NFRAC_L_SHIFT 0 #define QCA956X_PLL_CPU_CONFIG1_NFRAC_L_MASK 0x1f #define QCA956X_PLL_CPU_CONFIG1_NFRAC_H_SHIFT 5 -#define QCA956X_PLL_CPU_CONFIG1_NFRAC_H_MASK 0x3fff +#define QCA956X_PLL_CPU_CONFIG1_NFRAC_H_MASK 0x1fff #define QCA956X_PLL_CPU_CONFIG1_NINT_SHIFT 18 #define QCA956X_PLL_CPU_CONFIG1_NINT_MASK 0x1ff @@ -566,7 +566,7 @@ #define QCA956X_PLL_DDR_CONFIG1_NFRAC_L_SHIFT 0 #define QCA956X_PLL_DDR_CONFIG1_NFRAC_L_MASK 0x1f #define QCA956X_PLL_DDR_CONFIG1_NFRAC_H_SHIFT 5 -#define QCA956X_PLL_DDR_CONFIG1_NFRAC_H_MASK 0x3fff +#define QCA956X_PLL_DDR_CONFIG1_NFRAC_H_MASK 0x1fff #define QCA956X_PLL_DDR_CONFIG1_NINT_SHIFT 18 #define QCA956X_PLL_DDR_CONFIG1_NINT_MASK 0x1ff -- 2.17.1

2 1

[U-Boot] [U-Boot, V3, PATCH 2/3] mips: add initial support for qca956x referenced board
by rosysong＠rosinson.com 07 Mar '19

07 Mar '19

From: Rosy Song <rosysong(a)rosinson.com> QCA9563 is CPU used on AP152 board : Clock speed : 750 MHz , Arch : Mips 74Kc, Eth : SGMII interface, MIMO config : 3 * 3 450M, 2 * USB 2.0, Signed-off-by: Rosy Song <rosysong(a)rosinson.com> Changes for v2: - coding Style cleanup - remove ununsed flash chip in defconfig - enable automatic icache / dcache size in defconfig Changes for v3: - add detailed information for qca956x in commit message --- arch/mips/dts/Makefile | 1 + arch/mips/dts/ap152.dts | 48 ++ arch/mips/dts/qca956x.dtsi | 87 ++++ arch/mips/mach-ath79/Kconfig | 14 + arch/mips/mach-ath79/Makefile | 1 + .../mach-ath79/include/mach/ar71xx_regs.h | 73 +++ arch/mips/mach-ath79/include/mach/ath79.h | 3 + arch/mips/mach-ath79/qca956x/Makefile | 5 + arch/mips/mach-ath79/qca956x/clk.c | 419 ++++++++++++++++++ arch/mips/mach-ath79/qca956x/cpu.c | 9 + arch/mips/mach-ath79/qca956x/ddr.c | 308 +++++++++++++ .../mips/mach-ath79/qca956x/qca956x-ddr-tap.S | 193 ++++++++ arch/mips/mach-ath79/reset.c | 271 +++++++++++ board/qca/ap152/Kconfig | 15 + board/qca/ap152/MAINTAINERS | 6 + board/qca/ap152/Makefile | 3 + board/qca/ap152/ap152.c | 81 ++++ configs/ap152_defconfig | 49 ++ include/configs/ap152.h | 54 +++ 19 files changed, 1640 insertions(+) create mode 100644 arch/mips/dts/ap152.dts create mode 100644 arch/mips/dts/qca956x.dtsi create mode 100644 arch/mips/mach-ath79/qca956x/Makefile create mode 100644 arch/mips/mach-ath79/qca956x/clk.c create mode 100644 arch/mips/mach-ath79/qca956x/cpu.c create mode 100644 arch/mips/mach-ath79/qca956x/ddr.c create mode 100644 arch/mips/mach-ath79/qca956x/qca956x-ddr-tap.S create mode 100644 board/qca/ap152/Kconfig create mode 100644 board/qca/ap152/MAINTAINERS create mode 100644 board/qca/ap152/Makefile create mode 100644 board/qca/ap152/ap152.c create mode 100644 configs/ap152_defconfig create mode 100644 include/configs/ap152.h diff --git a/arch/mips/dts/Makefile b/arch/mips/dts/Makefile index b94b582837..621c35f0ef 100644 --- a/arch/mips/dts/Makefile +++ b/arch/mips/dts/Makefile @@ -2,6 +2,7 @@ dtb-$(CONFIG_TARGET_AP121) += ap121.dtb dtb-$(CONFIG_TARGET_AP143) += ap143.dtb +dtb-$(CONFIG_TARGET_AP152) += ap152.dtb dtb-$(CONFIG_TARGET_BOSTON) += img,boston.dtb dtb-$(CONFIG_TARGET_MALTA) += mti,malta.dtb dtb-$(CONFIG_TARGET_PIC32MZDASK) += pic32mzda_sk.dtb diff --git a/arch/mips/dts/ap152.dts b/arch/mips/dts/ap152.dts new file mode 100644 index 0000000000..1722290c73 --- /dev/null +++ b/arch/mips/dts/ap152.dts @@ -0,0 +1,48 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 Rosy Song <rosysong(a)rosinson.com> + */ + +/dts-v1/; +#include "qca956x.dtsi" + +/ { + model = "AP152 Reference Board"; + compatible = "qca,ap152", "qca,qca956x"; + + aliases { + spi0 = &spi0; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&gmac0 { + phy-mode = "sgmii"; + status = "okay"; +}; + +&xtal { + clock-frequency = <25000000>; +}; + +&uart0 { + clock-frequency = <25000000>; + status = "okay"; +}; + +&spi0 { + spi-max-frequency = <25000000>; + status = "okay"; + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-flash"; + memory-map = <0x9f000000 0x01000000>; + spi-max-frequency = <25000000>; + reg = <0>; + }; +}; diff --git a/arch/mips/dts/qca956x.dtsi b/arch/mips/dts/qca956x.dtsi new file mode 100644 index 0000000000..6cb360b3f8 --- /dev/null +++ b/arch/mips/dts/qca956x.dtsi @@ -0,0 +1,87 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 Rosy Song <rosysong(a)rosinson.com> + */ + +#include "skeleton.dtsi" + +/ { + compatible = "qca,qca956x"; + + #address-cells = <1>; + #size-cells = <1>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "mips,mips74Kc"; + reg = <0>; + }; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + xtal: xtal { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-output-names = "xtal"; + }; + }; + + ahb { + compatible = "simple-bus"; + ranges; + + #address-cells = <1>; + #size-cells = <1>; + + apb { + compatible = "simple-bus"; + ranges; + + #address-cells = <1>; + #size-cells = <1>; + + uart0: uart@18020000 { + compatible = "ns16550"; + reg = <0x18020000 0x20>; + reg-shift = <2>; + + status = "disabled"; + }; + + gmac0: eth@0x19000000 { + compatible = "qca,ag956x-mac"; + reg = <0x19000000 0x200>; + phy = <&phy0>; + phy-mode = "sgmii"; + + status = "disabled"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <0>; + }; + }; + }; + }; + + spi0: spi@1f000000 { + compatible = "qca,ar7100-spi"; + reg = <0x1f000000 0x10>; + + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + }; + }; +}; diff --git a/arch/mips/mach-ath79/Kconfig b/arch/mips/mach-ath79/Kconfig index bc86f591df..bdb23b5765 100644 --- a/arch/mips/mach-ath79/Kconfig +++ b/arch/mips/mach-ath79/Kconfig @@ -33,6 +33,15 @@ config SOC_QCA953X help This supports QCA/Atheros qca953x family SOCs. +config SOC_QCA956X + bool + select MIPS_TUNE_74KC + select SUPPORTS_BIG_ENDIAN + select SUPPORTS_CPU_MIPS32_R1 + select SUPPORTS_CPU_MIPS32_R2 + help + This supports QCA/Atheros qca956x family SOCs. + choice prompt "Board select" @@ -44,6 +53,10 @@ config TARGET_AP143 bool "AP143 Reference Board" select SOC_QCA953X +config TARGET_AP152 + bool "AP152 Reference Board" + select SOC_QCA956X + config BOARD_TPLINK_WDR4300 bool "TP-Link WDR4300 Board" select SOC_AR934X @@ -52,6 +65,7 @@ endchoice source "board/qca/ap121/Kconfig" source "board/qca/ap143/Kconfig" +source "board/qca/ap152/Kconfig" source "board/tplink/wdr4300/Kconfig" endmenu diff --git a/arch/mips/mach-ath79/Makefile b/arch/mips/mach-ath79/Makefile index 7aa40c65d3..fbd40c02be 100644 --- a/arch/mips/mach-ath79/Makefile +++ b/arch/mips/mach-ath79/Makefile @@ -7,3 +7,4 @@ obj-y += dram.o obj-$(CONFIG_SOC_AR933X) += ar933x/ obj-$(CONFIG_SOC_AR934X) += ar934x/ obj-$(CONFIG_SOC_QCA953X) += qca953x/ +obj-$(CONFIG_SOC_QCA956X) += qca956x/ diff --git a/arch/mips/mach-ath79/include/mach/ar71xx_regs.h b/arch/mips/mach-ath79/include/mach/ar71xx_regs.h index 5d371bb582..7cd16b8d81 100644 --- a/arch/mips/mach-ath79/include/mach/ar71xx_regs.h +++ b/arch/mips/mach-ath79/include/mach/ar71xx_regs.h @@ -194,6 +194,9 @@ #define QCA956X_WMAC_BASE \ (AR71XX_APB_BASE + 0x00100000) #define QCA956X_WMAC_SIZE 0x20000 +#define QCA956X_RTC_BASE \ + (AR71XX_APB_BASE + 0x00107000) +#define QCA956X_RTC_SIZE 0x1000 #define QCA956X_EHCI0_BASE 0x1b000000 #define QCA956X_EHCI1_BASE 0x1b400000 #define QCA956X_EHCI_SIZE 0x200 @@ -201,6 +204,10 @@ (AR71XX_APB_BASE + 0x00070000) #define QCA956X_GMAC_SIZE 0x64 +#define QCA956X_SRIF_BASE \ + (AR71XX_APB_BASE + 0x00116000) +#define QCA956X_SRIF_SIZE 0x1000 + /* * DDR_CTRL block */ @@ -278,6 +285,18 @@ #define QCA953X_DDR_REG_CTL_CONF 0x108 #define QCA953X_DDR_REG_CONFIG3 0x15c +#define QCA956X_DDR_REG_TAP_CTRL2 0x24 +#define QCA956X_DDR_REG_TAP_CTRL3 0x28 +#define QCA956X_DDR_REG_DDR2_CONFIG 0xb8 +#define QCA956X_DDR_REG_DDR2_EMR2 0xbc +#define QCA956X_DDR_REG_DDR2_EMR3 0xc0 +#define QCA956X_DDR_REG_BURST 0xc4 +#define QCA956X_DDR_REG_BURST2 0xc8 +#define QCA956X_DDR_REG_TIMEOUT_MAX 0xcc +#define QCA956X_DDR_REG_FSM_WAIT_CTRL 0xe4 +#define QCA956X_DDR_REG_CTL_CONF 0x108 +#define QCA956X_DDR_REG_DDR3_CONFIG 0x15c + /* * PLL block */ @@ -519,6 +538,13 @@ #define QCA956X_PLL_DDR_CONFIG_REG 0x08 #define QCA956X_PLL_DDR_CONFIG1_REG 0x0c #define QCA956X_PLL_CLK_CTRL_REG 0x10 +#define QCA956X_PLL_SWITCH_CLK_CTRL_REG 0x28 +#define QCA956X_PLL_ETH_XMII_CTRL_REG 0x30 +#define QCA956X_PLL_DDR_DIT_FRAC_REG 0x38 +#define QCA956X_PLL_DDR_DIT2_FRAC_REG 0x3c +#define QCA956X_PLL_CPU_DIT_FRAC_REG 0x40 +#define QCA956X_PLL_CPU_DIT2_FRAC_REG 0x44 +#define QCA956X_PLL_ETH_SGMII_SERDES_REG 0x4c #define QCA956X_PLL_CPU_CONFIG_REFDIV_SHIFT 12 #define QCA956X_PLL_CPU_CONFIG_REFDIV_MASK 0x1f @@ -756,6 +782,17 @@ #define QCA955X_RESET_MBOX BIT(1) #define QCA955X_RESET_I2S BIT(0) +#define QCA956X_RESET_EXTERNAL BIT(28) +#define QCA956X_RESET_FULL_CHIP BIT(24) +#define QCA956X_RESET_GE1_MDIO BIT(23) /* Reserved in datasheet */ +#define QCA956X_RESET_GE0_MDIO BIT(22) +#define QCA956X_RESET_GE1_MAC BIT(13) /* Reserved in datasheet */ +#define QCA956X_RESET_SGMII_ASSERT BIT(12) +#define QCA956X_RESET_GE0_MAC BIT(9) +#define QCA956X_RESET_SGMII BIT(8) +#define QCA956X_RESET_SGMII_ANALOG BIT(2) +#define QCA956X_RESET_SWITCH BIT(0) + #define AR933X_BOOTSTRAP_MDIO_GPIO_EN BIT(18) #define AR933X_BOOTSTRAP_DDR2 BIT(13) #define AR933X_BOOTSTRAP_EEPBUSY BIT(4) @@ -1099,8 +1136,12 @@ #define QCA953X_GPIO_IN_MUX_UART0_SIN 9 #define QCA953X_GPIO_IN_MUX_SPI_DATA_IN 8 +#define QCA956X_GPIO(x) BIT(x) +#define QCA956X_GPIO_MUX_MASK(x) (0xff << (x)) #define QCA956X_GPIO_OUT_MUX_GE0_MDO 32 #define QCA956X_GPIO_OUT_MUX_GE0_MDC 33 +#define QCA956X_GPIO_IN_MUX_UART0_SIN 0x12 +#define QCA956X_GPIO_OUT_MUX_UART0_SOUT 0x16 #define AR71XX_GPIO_COUNT 16 #define AR7240_GPIO_COUNT 18 @@ -1179,6 +1220,25 @@ #define QCA953X_SRIF_DPLL2_OUTDIV_SHIFT 13 #define QCA953X_SRIF_DPLL2_OUTDIV_MASK 0x7 +#define QCA956X_SRIF_BB_DPLL1_REG 0x180 +#define QCA956X_SRIF_BB_DPLL2_REG 0x184 +#define QCA956X_SRIF_BB_DPLL3_REG 0x188 + +#define QCA956X_SRIF_CPU_DPLL1_REG 0xf00 +#define QCA956X_SRIF_CPU_DPLL2_REG 0xf04 +#define QCA956X_SRIF_CPU_DPLL3_REG 0xf08 + +#define QCA956X_SRIF_DDR_DPLL1_REG 0xec0 +#define QCA956X_SRIF_DDR_DPLL2_REG 0xec4 +#define QCA956X_SRIF_DDR_DPLL3_REG 0xec8 + +#define QCA956X_SRIF_PCIE_DPLL1_REG 0xc80 +#define QCA956X_SRIF_PCIE_DPLL2_REG 0xc84 +#define QCA956X_SRIF_PCIE_DPLL3_REG 0xc88 + +#define QCA956X_SRIF_PMU1_REG 0xcc0 +#define QCA956X_SRIF_PMU2_REG 0xcc4 + /* * MII_CTRL block */ @@ -1261,4 +1321,17 @@ #define QCA955X_ETH_CFG_RGMII_EN BIT(0) #define QCA955X_ETH_CFG_GE0_SGMII BIT(6) +/* + * QCA956X GMAC Interface + */ + +#define QCA956X_GMAC_REG_ETH_CFG 0x00 +#define QCA956X_GMAC_REG_SGMII_RESET 0x14 +#define QCA956X_GMAC_REG_SGMII_SERDES 0x18 +#define QCA956X_GMAC_REG_MR_AN_CTRL 0x1c +#define QCA956X_GMAC_REG_SGMII_CONFIG 0x34 +#define QCA956X_GMAC_REG_SGMII_DEBUG 0x58 + +#define QCA956X_ETH_CFG_GE0_SGMII BIT(6) + #endif /* __ASM_AR71XX_H */ diff --git a/arch/mips/mach-ath79/include/mach/ath79.h b/arch/mips/mach-ath79/include/mach/ath79.h index 5de7a43f79..0fde5079b1 100644 --- a/arch/mips/mach-ath79/include/mach/ath79.h +++ b/arch/mips/mach-ath79/include/mach/ath79.h @@ -2,6 +2,7 @@ /* * Atheros AR71XX/AR724X/AR913X common definitions * + * Copyright (C) 2018-2019 Rosy Song <rosysong(a)rosinson.com> * Copyright (C) 2015-2016 Wills Wang <wills.wang(a)live.com> * Copyright (C) 2008-2011 Gabor Juhos <juhosg(a)openwrt.org> * Copyright (C) 2008 Imre Kaloz <kaloz(a)openwrt.org> @@ -146,4 +147,6 @@ int ath79_usb_reset(void); void ar934x_pll_init(const u16 cpu_mhz, const u16 ddr_mhz, const u16 ahb_mhz); void ar934x_ddr_init(const u16 cpu_mhz, const u16 ddr_mhz, const u16 ahb_mhz); +void qca956x_pll_init(void); +void qca956x_ddr_init(void); #endif /* __ASM_MACH_ATH79_H */ diff --git a/arch/mips/mach-ath79/qca956x/Makefile b/arch/mips/mach-ath79/qca956x/Makefile new file mode 100644 index 0000000000..3f5fc0363f --- /dev/null +++ b/arch/mips/mach-ath79/qca956x/Makefile @@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0+ + +obj-y += cpu.o +obj-y += clk.o +obj-y += ddr.o qca956x-ddr-tap.o diff --git a/arch/mips/mach-ath79/qca956x/clk.c b/arch/mips/mach-ath79/qca956x/clk.c new file mode 100644 index 0000000000..ca956d1291 --- /dev/null +++ b/arch/mips/mach-ath79/qca956x/clk.c @@ -0,0 +1,419 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2019 Rosy Song <rosysong(a)rosinson.com> + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/addrspace.h> +#include <asm/types.h> +#include <mach/ar71xx_regs.h> +#include <mach/ath79.h> +#include <wait_bit.h> + +#define PLL_SRIF_DPLL2_KI_LSB 29 +#define PLL_SRIF_DPLL2_KI_MASK 0x60000000 +#define PLL_SRIF_DPLL2_KI_SET(x) \ + (((x) << PLL_SRIF_DPLL2_KI_LSB) & PLL_SRIF_DPLL2_KI_MASK) +#define PLL_SRIF_DPLL2_KD_LSB 25 +#define PLL_SRIF_DPLL2_KD_MASK 0x1e000000 +#define PLL_SRIF_DPLL2_KD_SET(x) \ + (((x) << PLL_SRIF_DPLL2_KD_LSB) & PLL_SRIF_DPLL2_KD_MASK) +#define PLL_SRIF_DPLL2_PLL_PWD_LSB 22 +#define PLL_SRIF_DPLL2_PLL_PWD_MASK 0x00400000 +#define PLL_SRIF_DPLL2_PLL_PWD_SET(x) \ + (((x) << PLL_SRIF_DPLL2_PLL_PWD_LSB) & PLL_SRIF_DPLL2_PLL_PWD_MASK) +#define PLL_SRIF_DPLL2_OUTDIV_LSB 19 +#define PLL_SRIF_DPLL2_OUTDIV_MASK 0x00380000 +#define PLL_SRIF_DPLL2_OUTDIV_SET(x) \ + (((x) << PLL_SRIF_DPLL2_OUTDIV_LSB) & PLL_SRIF_DPLL2_OUTDIV_MASK) +#define PLL_SRIF_DPLL2_PHASE_SHIFT_LSB 12 +#define PLL_SRIF_DPLL2_PHASE_SHIFT_MASK 0x0007f000 +#define PLL_SRIF_DPLL2_PHASE_SHIFT_SET(x) \ + (((x) << PLL_SRIF_DPLL2_PHASE_SHIFT_LSB) & PLL_SRIF_DPLL2_PHASE_SHIFT_MASK) +#define CPU_PLL_CONFIG_PLLPWD_LSB 30 +#define CPU_PLL_CONFIG_PLLPWD_MASK 0x40000000 +#define CPU_PLL_CONFIG_PLLPWD_SET(x) \ + (((x) << CPU_PLL_CONFIG_PLLPWD_LSB) & CPU_PLL_CONFIG_PLLPWD_MASK) +#define CPU_PLL_CONFIG_OUTDIV_LSB 19 +#define CPU_PLL_CONFIG_OUTDIV_MASK 0x00380000 +#define CPU_PLL_CONFIG_OUTDIV_SET(x) \ + (((x) << CPU_PLL_CONFIG_OUTDIV_LSB) & CPU_PLL_CONFIG_OUTDIV_MASK) +#define CPU_PLL_CONFIG_RANGE_LSB 17 +#define CPU_PLL_CONFIG_RANGE_MASK 0x00060000 +#define CPU_PLL_CONFIG_RANGE_SET(x) \ + (((x) << CPU_PLL_CONFIG_RANGE_LSB) & CPU_PLL_CONFIG_RANGE_MASK) +#define CPU_PLL_CONFIG_REFDIV_LSB 12 +#define CPU_PLL_CONFIG_REFDIV_MASK 0x0001f000 +#define CPU_PLL_CONFIG_REFDIV_SET(x) \ + (((x) << CPU_PLL_CONFIG_REFDIV_LSB) & CPU_PLL_CONFIG_REFDIV_MASK) +#define CPU_PLL_CONFIG1_NINT_LSB 18 +#define CPU_PLL_CONFIG1_NINT_MASK 0x07fc0000 +#define CPU_PLL_CONFIG1_NINT_SET(x) \ + (((x) << CPU_PLL_CONFIG1_NINT_LSB) & CPU_PLL_CONFIG1_NINT_MASK) +#define CPU_PLL_DITHER1_DITHER_EN_LSB 31 +#define CPU_PLL_DITHER1_DITHER_EN_MASK 0x80000000 +#define CPU_PLL_DITHER1_DITHER_EN_SET(x) \ + (((x) << CPU_PLL_DITHER1_DITHER_EN_LSB) & CPU_PLL_DITHER1_DITHER_EN_MASK) +#define CPU_PLL_DITHER1_UPDATE_COUNT_LSB 24 +#define CPU_PLL_DITHER1_UPDATE_COUNT_MASK 0x3f000000 +#define CPU_PLL_DITHER1_UPDATE_COUNT_SET(x) \ + (((x) << CPU_PLL_DITHER1_UPDATE_COUNT_LSB) & CPU_PLL_DITHER1_UPDATE_COUNT_MASK) +#define CPU_PLL_DITHER1_NFRAC_STEP_LSB 18 +#define CPU_PLL_DITHER1_NFRAC_STEP_MASK 0x00fc0000 +#define CPU_PLL_DITHER1_NFRAC_STEP_SET(x) \ + (((x) << CPU_PLL_DITHER1_NFRAC_STEP_LSB) & CPU_PLL_DITHER1_NFRAC_STEP_MASK) +#define CPU_PLL_DITHER1_NFRAC_MIN_LSB 0 +#define CPU_PLL_DITHER1_NFRAC_MIN_MASK 0x0003ffff +#define CPU_PLL_DITHER1_NFRAC_MIN_SET(x) \ + (((x) << CPU_PLL_DITHER1_NFRAC_MIN_LSB) & CPU_PLL_DITHER1_NFRAC_MIN_MASK) +#define CPU_PLL_DITHER2_NFRAC_MAX_LSB 0 +#define CPU_PLL_DITHER2_NFRAC_MAX_MASK 0x0003ffff +#define CPU_PLL_DITHER2_NFRAC_MAX_SET(x) \ + (((x) << CPU_PLL_DITHER2_NFRAC_MAX_LSB) & CPU_PLL_DITHER2_NFRAC_MAX_MASK) +#define DDR_PLL_CONFIG_PLLPWD_LSB 30 +#define DDR_PLL_CONFIG_PLLPWD_MASK 0x40000000 +#define DDR_PLL_CONFIG_PLLPWD_SET(x) \ + (((x) << DDR_PLL_CONFIG_PLLPWD_LSB) & DDR_PLL_CONFIG_PLLPWD_MASK) +#define DDR_PLL_CONFIG_OUTDIV_LSB 23 +#define DDR_PLL_CONFIG_OUTDIV_MASK 0x03800000 +#define DDR_PLL_CONFIG_OUTDIV_SET(x) \ + (((x) << DDR_PLL_CONFIG_OUTDIV_LSB) & DDR_PLL_CONFIG_OUTDIV_MASK) +#define DDR_PLL_CONFIG_RANGE_LSB 21 +#define DDR_PLL_CONFIG_RANGE_MASK 0x00600000 +#define DDR_PLL_CONFIG_RANGE_SET(x) \ + (((x) << DDR_PLL_CONFIG_RANGE_LSB) & DDR_PLL_CONFIG_RANGE_MASK) +#define DDR_PLL_CONFIG_REFDIV_LSB 16 +#define DDR_PLL_CONFIG_REFDIV_MASK 0x001f0000 +#define DDR_PLL_CONFIG_REFDIV_SET(x) \ + (((x) << DDR_PLL_CONFIG_REFDIV_LSB) & DDR_PLL_CONFIG_REFDIV_MASK) +#define DDR_PLL_CONFIG1_NINT_LSB 18 +#define DDR_PLL_CONFIG1_NINT_MASK 0x07fc0000 +#define DDR_PLL_CONFIG1_NINT_SET(x) \ + (((x) << DDR_PLL_CONFIG1_NINT_LSB) & DDR_PLL_CONFIG1_NINT_MASK) +#define DDR_PLL_DITHER1_DITHER_EN_LSB 31 +#define DDR_PLL_DITHER1_DITHER_EN_MASK 0x80000000 +#define DDR_PLL_DITHER1_DITHER_EN_SET(x) \ + (((x) << DDR_PLL_DITHER1_DITHER_EN_LSB) & DDR_PLL_DITHER1_DITHER_EN_MASK) +#define DDR_PLL_DITHER1_UPDATE_COUNT_LSB 27 +#define DDR_PLL_DITHER1_UPDATE_COUNT_MASK 0x78000000 +#define DDR_PLL_DITHER1_UPDATE_COUNT_SET(x) \ + (((x) << DDR_PLL_DITHER1_UPDATE_COUNT_LSB) & DDR_PLL_DITHER1_UPDATE_COUNT_MASK) +#define DDR_PLL_DITHER1_NFRAC_STEP_LSB 20 +#define DDR_PLL_DITHER1_NFRAC_STEP_MASK 0x07f00000 +#define DDR_PLL_DITHER1_NFRAC_STEP_SET(x) \ + (((x) << DDR_PLL_DITHER1_NFRAC_STEP_LSB) & DDR_PLL_DITHER1_NFRAC_STEP_MASK) +#define DDR_PLL_DITHER1_NFRAC_MIN_LSB 0 +#define DDR_PLL_DITHER1_NFRAC_MIN_MASK 0x0003ffff +#define DDR_PLL_DITHER1_NFRAC_MIN_SET(x) \ + (((x) << DDR_PLL_DITHER1_NFRAC_MIN_LSB) & DDR_PLL_DITHER1_NFRAC_MIN_MASK) +#define DDR_PLL_DITHER2_NFRAC_MAX_LSB 0 +#define DDR_PLL_DITHER2_NFRAC_MAX_MASK 0x0003ffff +#define DDR_PLL_DITHER2_NFRAC_MAX_SET(x) \ + (((x) << DDR_PLL_DITHER2_NFRAC_MAX_LSB) & DDR_PLL_DITHER2_NFRAC_MAX_MASK) +#define CPU_DDR_CLOCK_CONTROL_AHBCLK_FROM_DDRPLL_LSB 24 +#define CPU_DDR_CLOCK_CONTROL_AHBCLK_FROM_DDRPLL_MASK 0x01000000 +#define CPU_DDR_CLOCK_CONTROL_AHBCLK_FROM_DDRPLL_SET(x) \ + (((x) << CPU_DDR_CLOCK_CONTROL_AHBCLK_FROM_DDRPLL_LSB) & CPU_DDR_CLOCK_CONTROL_AHBCLK_FROM_DDRPLL_MASK) +#define CPU_DDR_CLOCK_CONTROL_CPU_DDR_CLK_FROM_CPUPLL_LSB 21 +#define CPU_DDR_CLOCK_CONTROL_CPU_DDR_CLK_FROM_CPUPLL_MASK 0x00200000 +#define CPU_DDR_CLOCK_CONTROL_CPU_DDR_CLK_FROM_CPUPLL_SET(x) \ + (((x) << CPU_DDR_CLOCK_CONTROL_CPU_DDR_CLK_FROM_CPUPLL_LSB) & CPU_DDR_CLOCK_CONTROL_CPU_DDR_CLK_FROM_CPUPLL_MASK) +#define CPU_DDR_CLOCK_CONTROL_CPU_DDR_CLK_FROM_DDRPLL_LSB 20 +#define CPU_DDR_CLOCK_CONTROL_CPU_DDR_CLK_FROM_DDRPLL_MASK 0x00100000 +#define CPU_DDR_CLOCK_CONTROL_CPU_DDR_CLK_FROM_DDRPLL_SET(x) \ + (((x) << CPU_DDR_CLOCK_CONTROL_CPU_DDR_CLK_FROM_DDRPLL_LSB) & CPU_DDR_CLOCK_CONTROL_CPU_DDR_CLK_FROM_DDRPLL_MASK) +#define CPU_DDR_CLOCK_CONTROL_AHB_POST_DIV_LSB 15 +#define CPU_DDR_CLOCK_CONTROL_AHB_POST_DIV_MASK 0x000f8000 +#define CPU_DDR_CLOCK_CONTROL_AHB_POST_DIV_SET(x) \ + (((x) << CPU_DDR_CLOCK_CONTROL_AHB_POST_DIV_LSB) & CPU_DDR_CLOCK_CONTROL_AHB_POST_DIV_MASK) +#define CPU_DDR_CLOCK_CONTROL_DDR_POST_DIV_LSB 10 +#define CPU_DDR_CLOCK_CONTROL_DDR_POST_DIV_MASK 0x00007c00 +#define CPU_DDR_CLOCK_CONTROL_DDR_POST_DIV_SET(x) \ + (((x) << CPU_DDR_CLOCK_CONTROL_DDR_POST_DIV_LSB) & CPU_DDR_CLOCK_CONTROL_DDR_POST_DIV_MASK) +#define CPU_DDR_CLOCK_CONTROL_CPU_POST_DIV_LSB 5 +#define CPU_DDR_CLOCK_CONTROL_CPU_POST_DIV_MASK 0x000003e0 +#define CPU_DDR_CLOCK_CONTROL_CPU_POST_DIV_SET(x) \ + (((x) << CPU_DDR_CLOCK_CONTROL_CPU_POST_DIV_LSB) & CPU_DDR_CLOCK_CONTROL_CPU_POST_DIV_MASK) +#define CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_LSB 4 +#define CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_MASK 0x00000010 +#define CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_SET(x) \ + (((x) << CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_LSB) & CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_MASK) +#define CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_LSB 3 +#define CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_MASK 0x00000008 +#define CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_SET(x) \ + (((x) << CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_LSB) & CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_MASK) +#define CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_LSB 2 +#define CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_MASK 0x00000004 +#define CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_SET(x) \ + (((x) << CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_LSB) & CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_MASK) + +#define CPU_PLL_CONFIG1_NINT_VAL CPU_PLL_CONFIG1_NINT_SET(0x1f) +#define CPU_PLL_CONFIG_REF_DIV_VAL CPU_PLL_CONFIG_REFDIV_SET(0x1) +#define CPU_PLL_CONFIG_RANGE_VAL CPU_PLL_CONFIG_RANGE_SET(0) +#define CPU_PLL_CONFIG_OUT_DIV_VAL1 CPU_PLL_CONFIG_OUTDIV_SET(0) +#define CPU_PLL_CONFIG_OUT_DIV_VAL2 CPU_PLL_CONFIG_OUTDIV_SET(0) +#define CPU_PLL_DITHER1_VAL CPU_PLL_DITHER1_DITHER_EN_SET(0) | \ + CPU_PLL_DITHER1_NFRAC_MIN_SET(0) | \ + CPU_PLL_DITHER1_NFRAC_STEP_SET(0) | \ + CPU_PLL_DITHER1_UPDATE_COUNT_SET(0x0) +#define CPU_PLL_DITHER2_VAL CPU_PLL_DITHER2_NFRAC_MAX_SET(0x0) +#define DDR_PLL_CONFIG1_NINT_VAL DDR_PLL_CONFIG1_NINT_SET(0x1a) +#define DDR_PLL_CONFIG_REF_DIV_VAL DDR_PLL_CONFIG_REFDIV_SET(0x1) +#define DDR_PLL_CONFIG_RANGE_VAL DDR_PLL_CONFIG_RANGE_SET(0) +#define DDR_PLL_CONFIG_OUT_DIV_VAL1 DDR_PLL_CONFIG_OUTDIV_SET(0) +#define DDR_PLL_CONFIG_OUT_DIV_VAL2 DDR_PLL_CONFIG_OUTDIV_SET(0) +#define DDR_PLL_DITHER1_VAL DDR_PLL_DITHER1_DITHER_EN_SET(0) | \ + DDR_PLL_DITHER1_NFRAC_MIN_SET(0) | \ + DDR_PLL_DITHER1_NFRAC_STEP_SET(0) | \ + DDR_PLL_DITHER1_UPDATE_COUNT_SET(0x0) +#define DDR_PLL_DITHER2_VAL DDR_PLL_DITHER2_NFRAC_MAX_SET(0x0) +#define AHB_CLK_FROM_DDR CPU_DDR_CLOCK_CONTROL_AHBCLK_FROM_DDRPLL_SET(0) +#define CPU_AND_DDR_CLK_FROM_DDR \ + CPU_DDR_CLOCK_CONTROL_CPU_DDR_CLK_FROM_DDRPLL_SET(0) +#define CPU_AND_DDR_CLK_FROM_CPU \ + CPU_DDR_CLOCK_CONTROL_CPU_DDR_CLK_FROM_CPUPLL_SET(0) +#define CPU_DDR_CLOCK_CONTROL_AHB_DIV_VAL \ + CPU_DDR_CLOCK_CONTROL_AHB_POST_DIV_SET(0x2) +#define CPU_DDR_CLOCK_CONTROL_DDR_POST_DIV \ + CPU_DDR_CLOCK_CONTROL_DDR_POST_DIV_SET(0) +#define CPU_DDR_CLOCK_CONTROL_CPU_POST_DIV \ + CPU_DDR_CLOCK_CONTROL_CPU_POST_DIV_SET(0) + +static inline void set_val(u32 _reg, u32 _mask, u32 _val) +{ + void __iomem *pll_regs = map_physmem(AR71XX_PLL_BASE, + AR71XX_PLL_SIZE, MAP_NOCACHE); + writel((readl(pll_regs + _reg) & (~(_mask))) | _val, pll_regs + _reg); +} + +#define cpu_pll_set(_mask, _val) \ + set_val(QCA956X_PLL_CPU_CONFIG_REG, _mask, _val) + +#define ddr_pll_set(_mask, _val) \ + set_val(QCA956X_PLL_DDR_CONFIG_REG, _mask, _val) + +#define cpu_ddr_control_set(_mask, _val) \ + set_val(QCA956X_PLL_CLK_CTRL_REG, _mask, _val) + +DECLARE_GLOBAL_DATA_PTR; + +static u32 qca956x_get_xtal(void) +{ + u32 val; + + val = ath79_get_bootstrap(); + if (val & QCA956X_BOOTSTRAP_REF_CLK_40) + return 40000000; + else + return 25000000; +} + +int get_serial_clock(void) +{ + return qca956x_get_xtal(); +} + +void qca956x_pll_init(void) +{ + void __iomem *srif_regs = map_physmem(QCA956X_SRIF_BASE, + QCA956X_SRIF_SIZE, MAP_NOCACHE); + void __iomem *pll_regs = map_physmem(AR71XX_PLL_BASE, + AR71XX_PLL_SIZE, MAP_NOCACHE); + + /* 8.16.2 Baseband DPLL2 */ + writel(PLL_SRIF_DPLL2_KI_SET(2) | PLL_SRIF_DPLL2_KD_SET(0xa) | + PLL_SRIF_DPLL2_PLL_PWD_SET(1) | PLL_SRIF_DPLL2_OUTDIV_SET(1) | + PLL_SRIF_DPLL2_PHASE_SHIFT_SET(6), srif_regs + QCA956X_SRIF_BB_DPLL2_REG); + + /* 8.16.2 PCIE DPLL2 */ + writel(PLL_SRIF_DPLL2_KI_SET(2) | PLL_SRIF_DPLL2_KD_SET(0xa) | + PLL_SRIF_DPLL2_PLL_PWD_SET(1) | PLL_SRIF_DPLL2_OUTDIV_SET(3) | + PLL_SRIF_DPLL2_PHASE_SHIFT_SET(6), srif_regs + QCA956X_SRIF_PCIE_DPLL2_REG); + + /* 8.16.2 DDR DPLL2 */ + writel(PLL_SRIF_DPLL2_KI_SET(2) | PLL_SRIF_DPLL2_KD_SET(0xa) | + PLL_SRIF_DPLL2_PLL_PWD_SET(1) | PLL_SRIF_DPLL2_PHASE_SHIFT_SET(6), + srif_regs + QCA956X_SRIF_DDR_DPLL2_REG); + + /* 8.16.2 CPU DPLL2 */ + writel(PLL_SRIF_DPLL2_KI_SET(1) | PLL_SRIF_DPLL2_KD_SET(7) | + PLL_SRIF_DPLL2_PLL_PWD_SET(1) | PLL_SRIF_DPLL2_PHASE_SHIFT_SET(6), + srif_regs + QCA956X_SRIF_CPU_DPLL2_REG); + + /* pll_bypass_set */ + cpu_ddr_control_set(CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_MASK, + CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_SET(1)); + cpu_ddr_control_set(CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_MASK, + CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_SET(1)); + cpu_ddr_control_set(CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_MASK, + CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_SET(1)); + + /* init_cpu_pll */ + cpu_pll_set(CPU_PLL_CONFIG_PLLPWD_MASK, CPU_PLL_CONFIG_PLLPWD_SET(1)); + cpu_pll_set(CPU_PLL_CONFIG_REFDIV_MASK, CPU_PLL_CONFIG_REF_DIV_VAL); + cpu_pll_set(CPU_PLL_CONFIG_RANGE_MASK, CPU_PLL_CONFIG_RANGE_VAL); + cpu_pll_set(CPU_PLL_CONFIG_OUTDIV_MASK, CPU_PLL_CONFIG_OUT_DIV_VAL1); + set_val(QCA956X_PLL_CPU_CONFIG1_REG, CPU_PLL_CONFIG1_NINT_MASK, \ + CPU_PLL_CONFIG1_NINT_VAL); + + /* init_ddr_pll */ + ddr_pll_set(DDR_PLL_CONFIG_PLLPWD_MASK, DDR_PLL_CONFIG_PLLPWD_SET(1)); + ddr_pll_set(DDR_PLL_CONFIG_REFDIV_MASK, DDR_PLL_CONFIG_REF_DIV_VAL); + ddr_pll_set(DDR_PLL_CONFIG_RANGE_MASK, DDR_PLL_CONFIG_RANGE_VAL); + ddr_pll_set(DDR_PLL_CONFIG_OUTDIV_MASK, DDR_PLL_CONFIG_OUT_DIV_VAL1); + set_val(QCA956X_PLL_DDR_CONFIG1_REG, DDR_PLL_CONFIG1_NINT_MASK, + DDR_PLL_CONFIG1_NINT_VAL); + + /* init_ahb_pll */ + writel(CPU_DDR_CLOCK_CONTROL_AHB_DIV_VAL | AHB_CLK_FROM_DDR | + CPU_AND_DDR_CLK_FROM_DDR | CPU_AND_DDR_CLK_FROM_CPU | + CPU_DDR_CLOCK_CONTROL_DDR_POST_DIV | CPU_DDR_CLOCK_CONTROL_CPU_POST_DIV | + CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_SET(1) | + CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_SET(1) | + CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_SET(1), pll_regs + QCA956X_PLL_CLK_CTRL_REG); + + /* ddr_pll_dither_unset */ + writel(DDR_PLL_DITHER1_VAL, pll_regs + QCA956X_PLL_DDR_DIT_FRAC_REG); + writel(DDR_PLL_DITHER2_VAL, pll_regs + QCA956X_PLL_DDR_DIT2_FRAC_REG); + + /* cpu_pll_dither_unset */ + writel(CPU_PLL_DITHER1_VAL, pll_regs + QCA956X_PLL_CPU_DIT_FRAC_REG); + writel(CPU_PLL_DITHER2_VAL, pll_regs + QCA956X_PLL_CPU_DIT2_FRAC_REG); + + /* pll_pwd_unset */ + cpu_pll_set(CPU_PLL_CONFIG_PLLPWD_MASK, CPU_PLL_CONFIG_PLLPWD_SET(0)); + ddr_pll_set(DDR_PLL_CONFIG_PLLPWD_MASK, DDR_PLL_CONFIG_PLLPWD_SET(0)); + + /* outdiv_unset */ + cpu_pll_set(CPU_PLL_CONFIG_OUTDIV_MASK, CPU_PLL_CONFIG_OUT_DIV_VAL2); + ddr_pll_set(DDR_PLL_CONFIG_OUTDIV_MASK, DDR_PLL_CONFIG_OUT_DIV_VAL2); + + /* pll_bypass_unset */ + cpu_ddr_control_set(CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_MASK, + CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_SET(0)); + cpu_ddr_control_set(CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_MASK, + CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_SET(0)); + cpu_ddr_control_set(CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_MASK, + CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_SET(0)); + + while (readl(pll_regs + QCA956X_PLL_CPU_CONFIG_REG) & 0x8000000) + /* NOP */; + + while (readl(pll_regs + QCA956X_PLL_DDR_CONFIG_REG) & 0x8000000) + /* NOP */; +} + +int get_clocks(void) +{ + void __iomem *regs; + u32 ref_rate, cpu_rate, ddr_rate, ahb_rate; + u32 out_div, ref_div, postdiv, nint, hfrac, lfrac, clk_ctrl; + u32 pll, cpu_pll, ddr_pll, misc; + + /* + * QCA956x timer init workaround has to be applied right before setting + * up the clock. Else, there will be no jiffies + */ + regs = map_physmem(AR71XX_RESET_BASE, AR71XX_RESET_SIZE, + MAP_NOCACHE); + misc = readl(regs + AR71XX_RESET_REG_MISC_INT_ENABLE); + misc |= MISC_INT_MIPS_SI_TIMERINT_MASK; + writel(misc, regs + AR71XX_RESET_REG_MISC_INT_ENABLE); + + regs = map_physmem(AR71XX_PLL_BASE, AR71XX_PLL_SIZE, + MAP_NOCACHE); + pll = readl(regs + QCA956X_PLL_CPU_CONFIG_REG); + out_div = (pll >> QCA956X_PLL_CPU_CONFIG_OUTDIV_SHIFT) & + QCA956X_PLL_CPU_CONFIG_OUTDIV_MASK; + ref_div = (pll >> QCA956X_PLL_CPU_CONFIG_REFDIV_SHIFT) & + QCA956X_PLL_CPU_CONFIG_REFDIV_MASK; + + pll = readl(regs + QCA956X_PLL_CPU_CONFIG1_REG); + nint = (pll >> QCA956X_PLL_CPU_CONFIG1_NINT_SHIFT) & + QCA956X_PLL_CPU_CONFIG1_NINT_MASK; + hfrac = (pll >> QCA956X_PLL_CPU_CONFIG1_NFRAC_H_SHIFT) & + QCA956X_PLL_CPU_CONFIG1_NFRAC_H_MASK; + lfrac = (pll >> QCA956X_PLL_CPU_CONFIG1_NFRAC_L_SHIFT) & + QCA956X_PLL_CPU_CONFIG1_NFRAC_L_MASK; + + ref_rate = qca956x_get_xtal(); + + cpu_pll = nint * ref_rate / ref_div; + cpu_pll += (lfrac * ref_rate) / ((ref_div * 25) << 13); + cpu_pll += (hfrac >> 13) * ref_rate / ref_div; + cpu_pll /= (1 << out_div); + + pll = readl(regs + QCA956X_PLL_DDR_CONFIG_REG); + out_div = (pll >> QCA956X_PLL_DDR_CONFIG_OUTDIV_SHIFT) & + QCA956X_PLL_DDR_CONFIG_OUTDIV_MASK; + ref_div = (pll >> QCA956X_PLL_DDR_CONFIG_REFDIV_SHIFT) & + QCA956X_PLL_DDR_CONFIG_REFDIV_MASK; + pll = readl(regs + QCA956X_PLL_DDR_CONFIG1_REG); + nint = (pll >> QCA956X_PLL_DDR_CONFIG1_NINT_SHIFT) & + QCA956X_PLL_DDR_CONFIG1_NINT_MASK; + hfrac = (pll >> QCA956X_PLL_DDR_CONFIG1_NFRAC_H_SHIFT) & + QCA956X_PLL_DDR_CONFIG1_NFRAC_H_MASK; + lfrac = (pll >> QCA956X_PLL_DDR_CONFIG1_NFRAC_L_SHIFT) & + QCA956X_PLL_DDR_CONFIG1_NFRAC_L_MASK; + + ddr_pll = nint * ref_rate / ref_div; + ddr_pll += (lfrac * ref_rate) / ((ref_div * 25) << 13); + ddr_pll += (hfrac >> 13) * ref_rate / ref_div; + ddr_pll /= (1 << out_div); + + clk_ctrl = readl(regs + QCA956X_PLL_CLK_CTRL_REG); + + postdiv = (clk_ctrl >> QCA956X_PLL_CLK_CTRL_CPU_POST_DIV_SHIFT) & + QCA956X_PLL_CLK_CTRL_CPU_POST_DIV_MASK; + + if (clk_ctrl & QCA956X_PLL_CLK_CTRL_CPU_PLL_BYPASS) + cpu_rate = ref_rate; + else if (clk_ctrl & QCA956X_PLL_CLK_CTRL_CPU_DDRCLK_FROM_CPUPLL) + cpu_rate = ddr_pll / (postdiv + 1); + else + cpu_rate = cpu_pll / (postdiv + 1); + + postdiv = (clk_ctrl >> QCA956X_PLL_CLK_CTRL_DDR_POST_DIV_SHIFT) & + QCA956X_PLL_CLK_CTRL_DDR_POST_DIV_MASK; + + if (clk_ctrl & QCA956X_PLL_CLK_CTRL_DDR_PLL_BYPASS) + ddr_rate = ref_rate; + else if (clk_ctrl & QCA956X_PLL_CLK_CTRL_CPU_DDRCLK_FROM_DDRPLL) + ddr_rate = cpu_pll / (postdiv + 1); + else + ddr_rate = ddr_pll / (postdiv + 1); + + postdiv = (clk_ctrl >> QCA956X_PLL_CLK_CTRL_AHB_POST_DIV_SHIFT) & + QCA956X_PLL_CLK_CTRL_AHB_POST_DIV_MASK; + + if (clk_ctrl & QCA956X_PLL_CLK_CTRL_AHB_PLL_BYPASS) + ahb_rate = ref_rate; + else if (clk_ctrl & QCA956X_PLL_CLK_CTRL_AHBCLK_FROM_DDRPLL) + ahb_rate = ddr_pll / (postdiv + 1); + else + ahb_rate = cpu_pll / (postdiv + 1); + + gd->cpu_clk = cpu_rate; + gd->mem_clk = ddr_rate; + gd->bus_clk = ahb_rate; + + debug("cpu_clk=%u, ddr_clk=%u, bus_clk=%u\n", + cpu_rate, ddr_rate, ahb_rate); + + return 0; +} + +ulong get_bus_freq(ulong dummy) +{ + if (!gd->bus_clk) + get_clocks(); + return gd->bus_clk; +} + +ulong get_ddr_freq(ulong dummy) +{ + if (!gd->mem_clk) + get_clocks(); + return gd->mem_clk; +} diff --git a/arch/mips/mach-ath79/qca956x/cpu.c b/arch/mips/mach-ath79/qca956x/cpu.c new file mode 100644 index 0000000000..08a8c84e72 --- /dev/null +++ b/arch/mips/mach-ath79/qca956x/cpu.c @@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2019 Rosy Song <rosysong(a)rosinson.com> + */ + +#include <common.h> + +/* The lowlevel_init() is not needed on QCA956X */ +void lowlevel_init(void) {} diff --git a/arch/mips/mach-ath79/qca956x/ddr.c b/arch/mips/mach-ath79/qca956x/ddr.c new file mode 100644 index 0000000000..fb2230430c --- /dev/null +++ b/arch/mips/mach-ath79/qca956x/ddr.c @@ -0,0 +1,308 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2019 Rosy Song <rosysong(a)rosinson.com> + * + * Based on QSDK + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/addrspace.h> +#include <asm/types.h> +#include <mach/ar71xx_regs.h> +#include <mach/ath79.h> + +#define DDR_FSM_WAIT_CTRL_VAL 0xa12 +#define DDR_CTL_CONFIG_SRAM_TSEL_LSB 30 +#define DDR_CTL_CONFIG_SRAM_TSEL_MASK 0xc0000000 +#define DDR_CTL_CONFIG_SRAM_TSEL_SET(x) \ + (((x) << DDR_CTL_CONFIG_SRAM_TSEL_LSB) & DDR_CTL_CONFIG_SRAM_TSEL_MASK) +#define DDR_CTL_CONFIG_GE0_SRAM_SYNC_LSB 20 +#define DDR_CTL_CONFIG_GE0_SRAM_SYNC_MASK 0x00100000 +#define DDR_CTL_CONFIG_GE0_SRAM_SYNC_SET(x) \ + (((x) << DDR_CTL_CONFIG_GE0_SRAM_SYNC_LSB) & DDR_CTL_CONFIG_GE0_SRAM_SYNC_MASK) +#define DDR_CTL_CONFIG_GE1_SRAM_SYNC_LSB 19 +#define DDR_CTL_CONFIG_GE1_SRAM_SYNC_MASK 0x00080000 +#define DDR_CTL_CONFIG_GE1_SRAM_SYNC_SET(x) \ + (((x) << DDR_CTL_CONFIG_GE1_SRAM_SYNC_LSB) & DDR_CTL_CONFIG_GE1_SRAM_SYNC_MASK) +#define DDR_CTL_CONFIG_USB_SRAM_SYNC_LSB 18 +#define DDR_CTL_CONFIG_USB_SRAM_SYNC_MASK 0x00040000 +#define DDR_CTL_CONFIG_USB_SRAM_SYNC_SET(x) \ + (((x) << DDR_CTL_CONFIG_USB_SRAM_SYNC_LSB) & DDR_CTL_CONFIG_USB_SRAM_SYNC_MASK) +#define DDR_CTL_CONFIG_PCIE_SRAM_SYNC_LSB 17 +#define DDR_CTL_CONFIG_PCIE_SRAM_SYNC_MASK 0x00020000 +#define DDR_CTL_CONFIG_PCIE_SRAM_SYNC_SET(x) \ + (((x) << DDR_CTL_CONFIG_PCIE_SRAM_SYNC_LSB) & DDR_CTL_CONFIG_PCIE_SRAM_SYNC_MASK) +#define DDR_CTL_CONFIG_WMAC_SRAM_SYNC_LSB 16 +#define DDR_CTL_CONFIG_WMAC_SRAM_SYNC_MASK 0x00010000 +#define DDR_CTL_CONFIG_WMAC_SRAM_SYNC_SET(x) \ + (((x) << DDR_CTL_CONFIG_WMAC_SRAM_SYNC_LSB) & DDR_CTL_CONFIG_WMAC_SRAM_SYNC_MASK) +#define DDR_CTL_CONFIG_MISC_SRC1_SRAM_SYNC_LSB 15 +#define DDR_CTL_CONFIG_MISC_SRC1_SRAM_SYNC_MASK 0x00008000 +#define DDR_CTL_CONFIG_MISC_SRC1_SRAM_SYNC_SET(x) \ + (((x) << DDR_CTL_CONFIG_MISC_SRC1_SRAM_SYNC_LSB) & DDR_CTL_CONFIG_MISC_SRC1_SRAM_SYNC_MASK) +#define DDR_CTL_CONFIG_MISC_SRC2_SRAM_SYNC_LSB 14 +#define DDR_CTL_CONFIG_MISC_SRC2_SRAM_SYNC_MASK 0x00004000 +#define DDR_CTL_CONFIG_MISC_SRC2_SRAM_SYNC_SET(x) \ + (((x) << DDR_CTL_CONFIG_MISC_SRC2_SRAM_SYNC_LSB) & DDR_CTL_CONFIG_MISC_SRC2_SRAM_SYNC_MASK) +#define DDR_CTL_CONFIG_PAD_DDR2_SEL_LSB 6 +#define DDR_CTL_CONFIG_PAD_DDR2_SEL_MASK 0x00000040 +#define DDR_CTL_CONFIG_PAD_DDR2_SEL_SET(x) \ + (((x) << DDR_CTL_CONFIG_PAD_DDR2_SEL_LSB) & DDR_CTL_CONFIG_PAD_DDR2_SEL_MASK) +#define DDR_CTL_CONFIG_CPU_DDR_SYNC_LSB 2 +#define DDR_CTL_CONFIG_CPU_DDR_SYNC_MASK 0x00000004 +#define DDR_CTL_CONFIG_CPU_DDR_SYNC_SET(x) \ + (((x) << DDR_CTL_CONFIG_CPU_DDR_SYNC_LSB) & DDR_CTL_CONFIG_CPU_DDR_SYNC_MASK) +#define DDR_CTL_CONFIG_HALF_WIDTH_LSB 1 +#define DDR_CTL_CONFIG_HALF_WIDTH_MASK 0x00000002 +#define DDR_CTL_CONFIG_HALF_WIDTH_SET(x) \ + (((x) << DDR_CTL_CONFIG_HALF_WIDTH_LSB) & DDR_CTL_CONFIG_HALF_WIDTH_MASK) +#define DDR_CONFIG_CAS_LATENCY_MSB_LSB 31 +#define DDR_CONFIG_CAS_LATENCY_MSB_MASK 0x80000000 +#define DDR_CONFIG_CAS_LATENCY_MSB_SET(x) \ + (((x) << DDR_CONFIG_CAS_LATENCY_MSB_LSB) & DDR_CONFIG_CAS_LATENCY_MSB_MASK) +#define DDR_CONFIG_OPEN_PAGE_LSB 30 +#define DDR_CONFIG_OPEN_PAGE_MASK 0x40000000 +#define DDR_CONFIG_OPEN_PAGE_SET(x) \ + (((x) << DDR_CONFIG_OPEN_PAGE_LSB) & DDR_CONFIG_OPEN_PAGE_MASK) +#define DDR_CONFIG_CAS_LATENCY_LSB 27 +#define DDR_CONFIG_CAS_LATENCY_MASK 0x38000000 +#define DDR_CONFIG_CAS_LATENCY_SET(x) \ + (((x) << DDR_CONFIG_CAS_LATENCY_LSB) & DDR_CONFIG_CAS_LATENCY_MASK) +#define DDR_CONFIG_TMRD_LSB 23 +#define DDR_CONFIG_TMRD_MASK 0x07800000 +#define DDR_CONFIG_TMRD_SET(x) \ + (((x) << DDR_CONFIG_TMRD_LSB) & DDR_CONFIG_TMRD_MASK) +#define DDR_CONFIG_TRFC_LSB 17 +#define DDR_CONFIG_TRFC_MASK 0x007e0000 +#define DDR_CONFIG_TRFC_SET(x) \ + (((x) << DDR_CONFIG_TRFC_LSB) & DDR_CONFIG_TRFC_MASK) +#define DDR_CONFIG_TRRD_LSB 13 +#define DDR_CONFIG_TRRD_MASK 0x0001e000 +#define DDR_CONFIG_TRRD_SET(x) \ + (((x) << DDR_CONFIG_TRRD_LSB) & DDR_CONFIG_TRRD_MASK) +#define DDR_CONFIG_TRP_LSB 9 +#define DDR_CONFIG_TRP_MASK 0x00001e00 +#define DDR_CONFIG_TRP_SET(x) \ + (((x) << DDR_CONFIG_TRP_LSB) & DDR_CONFIG_TRP_MASK) +#define DDR_CONFIG_TRCD_LSB 5 +#define DDR_CONFIG_TRCD_MASK 0x000001e0 +#define DDR_CONFIG_TRCD_SET(x) \ + (((x) << DDR_CONFIG_TRCD_LSB) & DDR_CONFIG_TRCD_MASK) +#define DDR_CONFIG_TRAS_LSB 0 +#define DDR_CONFIG_TRAS_MASK 0x0000001f +#define DDR_CONFIG_TRAS_SET(x) \ + (((x) << DDR_CONFIG_TRAS_LSB) & DDR_CONFIG_TRAS_MASK) +#define DDR_CONFIG2_HALF_WIDTH_LOW_LSB 31 +#define DDR_CONFIG2_HALF_WIDTH_LOW_MASK 0x80000000 +#define DDR_CONFIG2_HALF_WIDTH_LOW_SET(x) \ + (((x) << DDR_CONFIG2_HALF_WIDTH_LOW_LSB) & DDR_CONFIG2_HALF_WIDTH_LOW_MASK) +#define DDR_CONFIG2_SWAP_A26_A27_LSB 30 +#define DDR_CONFIG2_SWAP_A26_A27_MASK 0x40000000 +#define DDR_CONFIG2_SWAP_A26_A27_SET(x) \ + (((x) << DDR_CONFIG2_SWAP_A26_A27_LSB) & DDR_CONFIG2_SWAP_A26_A27_MASK) +#define DDR_CONFIG2_GATE_OPEN_LATENCY_LSB 26 +#define DDR_CONFIG2_GATE_OPEN_LATENCY_MASK 0x3c000000 +#define DDR_CONFIG2_GATE_OPEN_LATENCY_SET(x) \ + (((x) << DDR_CONFIG2_GATE_OPEN_LATENCY_LSB) & DDR_CONFIG2_GATE_OPEN_LATENCY_MASK) +#define DDR_CONFIG2_TWTR_LSB 21 +#define DDR_CONFIG2_TWTR_MASK 0x03e00000 +#define DDR_CONFIG2_TWTR_SET(x) \ + (((x) << DDR_CONFIG2_TWTR_LSB) & DDR_CONFIG2_TWTR_MASK) +#define DDR_CONFIG2_TRTP_LSB 17 +#define DDR_CONFIG2_TRTP_MASK 0x001e0000 +#define DDR_CONFIG2_TRTP_SET(x) \ + (((x) << DDR_CONFIG2_TRTP_LSB) & DDR_CONFIG2_TRTP_MASK) +#define DDR_CONFIG2_TRTW_LSB 12 +#define DDR_CONFIG2_TRTW_MASK 0x0001f000 +#define DDR_CONFIG2_TRTW_SET(x) \ + (((x) << DDR_CONFIG2_TRTW_LSB) & DDR_CONFIG2_TRTW_MASK) +#define DDR_CONFIG2_TWR_LSB 8 +#define DDR_CONFIG2_TWR_MASK 0x00000f00 +#define DDR_CONFIG2_TWR_SET(x) \ + (((x) << DDR_CONFIG2_TWR_LSB) & DDR_CONFIG2_TWR_MASK) +#define DDR_CONFIG2_CKE_LSB 7 +#define DDR_CONFIG2_CKE_MASK 0x00000080 +#define DDR_CONFIG2_CKE_SET(x) \ + (((x) << DDR_CONFIG2_CKE_LSB) & DDR_CONFIG2_CKE_MASK) +#define DDR_CONFIG2_CNTL_OE_EN_LSB 5 +#define DDR_CONFIG2_CNTL_OE_EN_MASK 0x00000020 +#define DDR_CONFIG2_CNTL_OE_EN_SET(x) \ + (((x) << DDR_CONFIG2_CNTL_OE_EN_LSB) & DDR_CONFIG2_CNTL_OE_EN_MASK) +#define DDR_CONFIG2_BURST_LENGTH_LSB 0 +#define DDR_CONFIG2_BURST_LENGTH_MASK 0x0000000f +#define DDR_CONFIG2_BURST_LENGTH_SET(x) \ + (((x) << DDR_CONFIG2_BURST_LENGTH_LSB) & DDR_CONFIG2_BURST_LENGTH_MASK) +#define RST_BOOTSTRAP_ADDRESS 0x180600b0 +#define PMU2_SWREGMSB_LSB 22 +#define PMU2_SWREGMSB_MASK 0xffc00000 +#define PMU2_SWREGMSB_SET(x) \ + (((x) << PMU2_SWREGMSB_LSB) & PMU2_SWREGMSB_MASK) +#define PMU2_PGM_LSB 21 +#define PMU2_PGM_MASK 0x00200000 +#define PMU2_PGM_SET(x) \ + (((x) << PMU2_PGM_LSB) & PMU2_PGM_MASK) + +#define CPU_DDR_SYNC_MODE DDR_CTL_CONFIG_CPU_DDR_SYNC_SET(0) + +/* +* DDR2 DDR1 +* 0x40c3 25MHz 0x4186 25Mhz +* 0x4138 40MHz 0x4270 40Mhz +*/ +#define CFG_DDR2_REFRESH_VAL 0x40c3 +#define CFG_DDR2_CONFIG_VAL DDR_CONFIG_CAS_LATENCY_MSB_SET(0x1) | \ + DDR_CONFIG_OPEN_PAGE_SET(0x1) | DDR_CONFIG_CAS_LATENCY_SET(0x4) | \ + DDR_CONFIG_TMRD_SET(0x6) | DDR_CONFIG_TRFC_SET(0x16) | \ + DDR_CONFIG_TRRD_SET(0x7) | DDR_CONFIG_TRP_SET(0xb) | \ + DDR_CONFIG_TRCD_SET(0xb) | DDR_CONFIG_TRAS_SET(0) +#define CFG_DDR2_CONFIG2_VAL DDR_CONFIG2_HALF_WIDTH_LOW_SET(0x1) | \ + DDR_CONFIG2_SWAP_A26_A27_SET(0x0) | DDR_CONFIG2_GATE_OPEN_LATENCY_SET(0xa) | \ + DDR_CONFIG2_TWTR_SET(0x16) | DDR_CONFIG2_TRTP_SET(0xa) | \ + DDR_CONFIG2_TRTW_SET(0xe) | DDR_CONFIG2_TWR_SET(0x2) | \ + DDR_CONFIG2_CKE_SET(0x1) | DDR_CONFIG2_CNTL_OE_EN_SET(0x1) | \ + DDR_CONFIG2_BURST_LENGTH_SET(0x8) + +#define CFG_DDR2_CONFIG3_VAL 0x0000000e +#define CFG_DDR2_EXT_MODE_VAL1 0x782 +#define CFG_DDR2_EXT_MODE_VAL2 0x402 +#define CFG_DDR2_MODE_VAL_INIT 0xb53 +#define CFG_DDR2_MODE_VAL 0xa53 +#define CFG_DDR2_TAP_VAL 0x10 +#define CFG_DDR2_EN_TWL_VAL 0x00001e91 +#define CFG_DDR2_RD_DATA_THIS_CYCLE_VAL_16 0xffff + +#define CFG_DDR_CTL_CONFIG DDR_CTL_CONFIG_SRAM_TSEL_SET(0x1) | \ + DDR_CTL_CONFIG_GE0_SRAM_SYNC_SET(0x1) | \ + DDR_CTL_CONFIG_GE1_SRAM_SYNC_SET(0x1) | \ + DDR_CTL_CONFIG_USB_SRAM_SYNC_SET(0x1) | \ + DDR_CTL_CONFIG_PCIE_SRAM_SYNC_SET(0x1) | \ + DDR_CTL_CONFIG_WMAC_SRAM_SYNC_SET(0x1) | \ + DDR_CTL_CONFIG_MISC_SRC1_SRAM_SYNC_SET(0x1) | \ + DDR_CTL_CONFIG_MISC_SRC2_SRAM_SYNC_SET(0x1) + +DECLARE_GLOBAL_DATA_PTR; + +void qca956x_ddr_init(void) +{ + u32 ddr_config, ddr_config2, ddr_config3, mod_val, \ + mod_val_init, cycle_val, tap_val, ctl_config; + void __iomem *ddr_regs = map_physmem(AR71XX_DDR_CTRL_BASE, AR71XX_DDR_CTRL_SIZE, + MAP_NOCACHE); + void __iomem *srif_regs = map_physmem(QCA956X_SRIF_BASE, QCA956X_SRIF_SIZE, + MAP_NOCACHE); + + ddr_config = CFG_DDR2_CONFIG_VAL; + ddr_config2 = CFG_DDR2_CONFIG2_VAL; + ddr_config3 = CFG_DDR2_CONFIG3_VAL; + mod_val_init = CFG_DDR2_MODE_VAL_INIT; + mod_val = CFG_DDR2_MODE_VAL; + tap_val = CFG_DDR2_TAP_VAL; + cycle_val = CFG_DDR2_RD_DATA_THIS_CYCLE_VAL_16; + ctl_config = CFG_DDR_CTL_CONFIG | DDR_CTL_CONFIG_PAD_DDR2_SEL_SET(0x1) | + DDR_CTL_CONFIG_HALF_WIDTH_SET(0x1) | CPU_DDR_SYNC_MODE; + + writel(0x10, ddr_regs + AR71XX_DDR_REG_CONTROL); + udelay(10); + + writel(0x20, ddr_regs + AR71XX_DDR_REG_CONTROL); + udelay(10); + + writel(ctl_config, ddr_regs + QCA956X_DDR_REG_CTL_CONF); + udelay(10); + + writel(cycle_val, ddr_regs + AR71XX_DDR_REG_RD_CYCLE); + udelay(100); + + writel(0x74444444, ddr_regs + QCA956X_DDR_REG_BURST); + udelay(100); + + writel(0x44444444, ddr_regs + QCA956X_DDR_REG_BURST2); + udelay(100); + + writel(DDR_FSM_WAIT_CTRL_VAL, ddr_regs + QCA956X_DDR_REG_FSM_WAIT_CTRL); + udelay(100); + + writel(0xfffff, ddr_regs + QCA956X_DDR_REG_TIMEOUT_MAX); + udelay(100); + + writel(ddr_config, ddr_regs + AR71XX_DDR_REG_CONFIG); + udelay(100); + + writel(ddr_config2, ddr_regs + AR71XX_DDR_REG_CONFIG2); + udelay(100); + + writel(ddr_config3, ddr_regs + QCA956X_DDR_REG_DDR3_CONFIG); + udelay(100); + + writel(CFG_DDR2_EN_TWL_VAL, ddr_regs + QCA956X_DDR_REG_DDR2_CONFIG); + udelay(100); + + writel(ddr_config2 | 0x80, ddr_regs + AR71XX_DDR_REG_CONFIG2); /* CKE Enable */ + udelay(100); + + writel(0x8, ddr_regs + AR71XX_DDR_REG_CONTROL); /* Precharge */ + udelay(10); + + writel(0, ddr_regs + QCA956X_DDR_REG_DDR2_EMR2); + writel(0x10, ddr_regs + AR71XX_DDR_REG_CONTROL); /* EMR2 */ + udelay(10); + + writel(0, ddr_regs + QCA956X_DDR_REG_DDR2_EMR3); + writel(0x20, ddr_regs + AR71XX_DDR_REG_CONTROL); /* EMR3 */ + udelay(10); + + /* EMR DLL enable, Reduced Driver Impedance control, Differential DQS disabled */ + writel(CFG_DDR2_EXT_MODE_VAL2, ddr_regs + AR71XX_DDR_REG_EMR); + udelay(100); + + writel(0x2, ddr_regs + AR71XX_DDR_REG_CONTROL); /* EMR write */ + udelay(10); + + writel(mod_val_init, ddr_regs + AR71XX_DDR_REG_MODE); + udelay(1000); + + writel(0x1, ddr_regs + AR71XX_DDR_REG_CONTROL); /* MR Write */ + udelay(10); + + writel(0x8, ddr_regs + AR71XX_DDR_REG_CONTROL); /* Precharge */ + udelay(10); + + writel(0x4, ddr_regs + AR71XX_DDR_REG_CONTROL); /* Auto Refresh */ + udelay(10); + + writel(0x4, ddr_regs + AR71XX_DDR_REG_CONTROL); /* Auto Refresh */ + udelay(10); + + /* Issue MRS to remove DLL out-of-reset */ + writel(mod_val, ddr_regs + AR71XX_DDR_REG_MODE); + udelay(100); + + writel(0x1, ddr_regs + AR71XX_DDR_REG_CONTROL); /* MR write */ + udelay(100); + + writel(CFG_DDR2_EXT_MODE_VAL1, ddr_regs + AR71XX_DDR_REG_EMR); + udelay(100); + + writel(0x2, ddr_regs + AR71XX_DDR_REG_CONTROL); /* EMR write */ + udelay(100); + + writel(CFG_DDR2_EXT_MODE_VAL2, ddr_regs + AR71XX_DDR_REG_EMR); + udelay(100); + + writel(0x2, ddr_regs + AR71XX_DDR_REG_CONTROL); /* EMR write */ + udelay(100); + + writel(CFG_DDR2_REFRESH_VAL, ddr_regs + AR71XX_DDR_REG_REFRESH); + udelay(100); + + writel(tap_val, ddr_regs + AR71XX_DDR_REG_TAP_CTRL0); + writel(tap_val, ddr_regs + AR71XX_DDR_REG_TAP_CTRL1); + writel(tap_val, ddr_regs + QCA956X_DDR_REG_TAP_CTRL2); + writel(tap_val, ddr_regs + QCA956X_DDR_REG_TAP_CTRL3); + + writel(0x633c8176, srif_regs + QCA956X_SRIF_PMU1_REG); + /* Set DDR2 Voltage to 1.8 volts */ + writel(PMU2_SWREGMSB_SET(0x40) | PMU2_PGM_SET(0x1), + srif_regs + QCA956X_SRIF_PMU2_REG); +} diff --git a/arch/mips/mach-ath79/qca956x/qca956x-ddr-tap.S b/arch/mips/mach-ath79/qca956x/qca956x-ddr-tap.S new file mode 100644 index 0000000000..db54b575fb --- /dev/null +++ b/arch/mips/mach-ath79/qca956x/qca956x-ddr-tap.S @@ -0,0 +1,193 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2019 Rosy Song <rosysong(a)rosinson.com> + * + * Based on QSDK + */ + +#include <config.h> +#include <asm/asm.h> +#include <asm/regdef.h> +#include <asm/mipsregs.h> +#include <asm/addrspace.h> +#include <mach/ar71xx_regs.h> + + .set noreorder + +LEAF(ddr_tap_tuning) + li a0, 0xbd001f00 + sw zero, 0x0(a0) /* Place where the tap values are saved and used for SWEEP */ + sw zero, 0x4(a0) /* Place where the number of passing taps are saved. */ + sw zero, 0x14(a0) /* Place where the last pass tap value is stored */ + li a1, 0xaa55aa55 /* Indicates that the First pass tap value is not found */ + sw a1, 0x10(a0) /* Place where the First pass tap value is stored */ + nop + + li a0, CKSEG1ADDR(AR71XX_RESET_BASE) /* RESET_BASE_ADDRESS */ + lw a1, 0x1c(a0) /* Reading the RST_RESET_ADDRESS */ + li a2, 0x08000000 /* Setting the RST_RESET_RTC_RESET */ + or a1, a1, a2 + sw a1, 0x1c(a0) + + li a3, 0xffffffff + xor a2, a2, a3 + and a1, a1, a2 + sw a1, 0x1c(a0) /* Taking the RTC out of RESET */ + nop + + li a0, CKSEG1ADDR(QCA956X_RTC_BASE) /* RTC_BASE_ADDRESS */ + li a1, 0x1 + sw a1, 0x0040(a0) /* RTC_SYNC_RESET_ADDRESS */ + + li a2, 0x2 + +_poll_for_RTC_ON: + lw a1, 0x0044(a0) /* RTC_SYNC_STATUS_ADDRESS */ + and a1, a2, a1 + bne a1, a2, _poll_for_RTC_ON + nop + +_CHANGE_TAPS: + li t0, 0xbd001f00 /* Read the current value of the TAP for programming */ + lw t1, 0x0(t0) + li t2, 0x00000000 + or t3, t1, t2 + + li t0, 0xb8000000 /* DDR_BASE_ADDRESS */ + sw t3, 0x1c(t0) /* TAP_CONTROL_0_ADDRESS */ + sw t3, 0x20(t0) /* TAP_CONTROL_1_ADDRESS */ + sw t3, 0x24(t0) /* TAP_CONTROL_2_ADDRESS */ + sw t3, 0x28(t0) /* TAP_CONTROL_3_ADDRESS */ + + li t1, 0x00000010 /* Running the test 8 times */ + sw t1, 0x0068(t0) /* PERF_COMP_ADDR_1_ADDRESS */ + + li t1, 0xfa5de83f /* 4 Row Address Bits, 4 Column Address Bits, 2 BA bits */ + sw t1, 0x002c(t0) /* PERF_MASK_ADDR_0_ADDRESS */ + + li t1, 0x0000ffff + sw t1, 0x0070(t0) /* PERF_COMP_AHB_GE0_1_ADDRESS */ + + li t1, 0x0000ffff + sw t1, 0x0040(t0) /* PERF_COMP_AHB_GE1_0_ADDRESS */ + + li t1, 0x0000ffff + sw t1, 0x0078(t0) /* PERF_COMP_AHB_GE1_1_ADDRESS */ + + li t1, 0x0000ffff + sw t1, 0x0034(t0) /* PERF_MASK_AHB_GE0_0_ADDRESS */ + + li t1, 0x0000ffff + sw t1, 0x006c(t0) /* PERF_MASK_AHB_GE0_1_ADDRESS */ + + li t1, 0x0000ffff + sw t1, 0x003c(t0) /* PERF_MASK_AHB_GE1_0_ADDRESS */ + + li t1, 0x0000ffff + sw t1, 0x0074(t0) /* PERF_MASK_AHB_GE1_1_ADDRESS */ + + li t1, 0x0000ffff + sw t1, 0x0038(t0) /* PERF_COMP_AHB_GE0_0_ADDRESS */ + + li t1, 0x00000001 + sw t1, 0x011c(t0) /* DDR_BIST_ADDRESS */ + + li t2, 0x1 + +_bist_done_poll: + lw t1, 0x0120(t0) /* DDR_BIST_STATUS_ADDRESS */ + and t1, t1, t2 + bne t1, t2, _bist_done_poll + nop + + lw t1, 0x0120(t0) /* DDR_BIST_STATUS_ADDRESS */ + li t4, 0x000001fe + and t2, t1, t4 + srl t2, t2, 0x1 /* no. of Pass Runs */ + + li t5, 0x00000000 + sw t5, 0x011c(t0) /* DDR_BIST_ADDRESS - Stop the DDR BIST test */ + + li t5, 0x0001fe00 + and t5, t5, t1 + bnez t5, _iterate_tap /* This is a redundant compare but nevertheless - Comparing the FAILS */ + nop + + lw t1, 0x0068(t0) /* PERF_COMP_ADDR_1_ADDRESS */ + li t3, 0x000001fe + and t3, t3, t1 + srl t3, t3, 0x1 /* No. of runs in the config register. */ + bne t3, t2, _iterate_tap + nop + +pass_tap: + li t0, 0xbd001f00 + lw t1, 0x4(t0) + addiu t1, t1, 0x1 + sw t1, 0x4(t0) + + li t0, 0xbd001f10 + lw t1, 0x0(t0) + li t2, 0xaa55aa55 + beq t1, t2, _first_pass + nop + + li t0, 0xbd001f00 + lw t1, 0x0(t0) + li t0, 0xbd001f10 + sw t1, 0x4(t0) + nop + b _iterate_tap + nop + +_first_pass: + li t0, 0xbd001f00 + lw t1, 0x0(t0) + li t0, 0xbd001f10 + sw t1, 0x0(t0) + sw t1, 0x4(t0) + nop + +_iterate_tap: + li t0, 0xbd001f00 + lw t1, 0x0(t0) + li t2, 0x3f + beq t1, t2, _STOP_TEST + nop + + addiu t1, t1, 0x1 + sw t1, 0x0(t0) + nop + b _CHANGE_TAPS + nop + +_STOP_TEST: + li t0, 0xbd001f00 + lw t1, 0x4(t0) + bnez t1, _load_center_tap + nop + + li t3, 0x8 /* Default Tap to be used */ + b _load_tap_into_reg + nop + +_load_center_tap: + li t0, 0xbd001f10 + lw t1, 0x0(t0) + lw t2, 0x4(t0) + add t3, t1, t2 + srl t3, t3, 0x1 + li t4, 0x3f + and t3, t3, t4 + +_load_tap_into_reg: + li t0, 0xb8000000 + sw t3, 0x1c(t0) /* TAP_CONTROL_0_ADDRESS */ + sw t3, 0x20(t0) /* TAP_CONTROL_1_ADDRESS */ + sw t3, 0x24(t0) /* TAP_CONTROL_2_ADDRESS */ + sw t3, 0x28(t0) /* TAP_CONTROL_3_ADDRESS */ + + nop + jr ra + nop + END(ddr_tap_tuning) diff --git a/arch/mips/mach-ath79/reset.c b/arch/mips/mach-ath79/reset.c index 6a94d886f9..0ab3ab6383 100644 --- a/arch/mips/mach-ath79/reset.c +++ b/arch/mips/mach-ath79/reset.c @@ -1,6 +1,7 @@ // SPDX-License-Identifier: GPL-2.0+ /* * Copyright (C) 2015-2016 Wills Wang <wills.wang(a)live.com> + * Copyright (C) 2018-2019 Rosy Song <rosysong(a)rosinson.com> */ #include <common.h> @@ -11,6 +12,44 @@ #include <mach/ath79.h> #include <mach/ar71xx_regs.h> +/* QCA956X ETH_SGMII_SERDES Registers */ +#define SGMII_SERDES_RES_CALIBRATION_LSB 23 +#define SGMII_SERDES_RES_CALIBRATION_MASK 0x07800000 +#define SGMII_SERDES_RES_CALIBRATION_SET(x) \ + (((x) << SGMII_SERDES_RES_CALIBRATION_LSB) & SGMII_SERDES_RES_CALIBRATION_MASK) +#define SGMII_SERDES_CDR_BW_LSB 1 +#define SGMII_SERDES_CDR_BW_MASK 0x00000006 +#define SGMII_SERDES_CDR_BW_SET(x) \ + (((x) << SGMII_SERDES_CDR_BW_LSB) & SGMII_SERDES_CDR_BW_MASK) +#define SGMII_SERDES_TX_DR_CTRL_LSB 4 +#define SGMII_SERDES_TX_DR_CTRL_MASK 0x00000070 +#define SGMII_SERDES_TX_DR_CTRL_SET(x) \ + (((x) << SGMII_SERDES_TX_DR_CTRL_LSB) & SGMII_SERDES_TX_DR_CTRL_MASK) +#define SGMII_SERDES_PLL_BW_LSB 8 +#define SGMII_SERDES_PLL_BW_MASK 0x00000100 +#define SGMII_SERDES_PLL_BW_SET(x) \ + (((x) << SGMII_SERDES_PLL_BW_LSB) & SGMII_SERDES_PLL_BW_MASK) +#define SGMII_SERDES_EN_SIGNAL_DETECT_LSB 16 +#define SGMII_SERDES_EN_SIGNAL_DETECT_MASK 0x00010000 +#define SGMII_SERDES_EN_SIGNAL_DETECT_SET(x) \ + (((x) << SGMII_SERDES_EN_SIGNAL_DETECT_LSB) & SGMII_SERDES_EN_SIGNAL_DETECT_MASK) +#define SGMII_SERDES_FIBER_SDO_LSB 17 +#define SGMII_SERDES_FIBER_SDO_MASK 0x00020000 +#define SGMII_SERDES_FIBER_SDO_SET(x) \ + (((x) << SGMII_SERDES_FIBER_SDO_LSB) & SGMII_SERDES_FIBER_SDO_MASK) +#define SGMII_SERDES_VCO_REG_LSB 27 +#define SGMII_SERDES_VCO_REG_MASK 0x78000000 +#define SGMII_SERDES_VCO_REG_SET(x) \ + (((x) << SGMII_SERDES_VCO_REG_LSB) & SGMII_SERDES_VCO_REG_MASK) +#define SGMII_SERDES_VCO_FAST_LSB 9 +#define SGMII_SERDES_VCO_FAST_MASK 0x00000200 +#define SGMII_SERDES_VCO_FAST_GET(x) \ + (((x) & SGMII_SERDES_VCO_FAST_MASK) >> SGMII_SERDES_VCO_FAST_LSB) +#define SGMII_SERDES_VCO_SLOW_LSB 10 +#define SGMII_SERDES_VCO_SLOW_MASK 0x00000400 +#define SGMII_SERDES_VCO_SLOW_GET(x) \ + (((x) & SGMII_SERDES_VCO_SLOW_MASK) >> SGMII_SERDES_VCO_SLOW_LSB) + void _machine_restart(void) { void __iomem *base; @@ -152,6 +191,236 @@ static int eth_init_qca953x(void) return 0; } +static int qca956x_sgmii_cal(void) +{ + int i; + u32 reg, rev_sgmii_val; + u32 vco_fast, vco_slow; + u32 start_val = 0, end_val = 0; + void __iomem *gregs = map_physmem(AR71XX_MII_BASE, AR71XX_MII_SIZE, + MAP_NOCACHE); + void __iomem *pregs = map_physmem(AR71XX_PLL_BASE, AR71XX_PLL_SIZE, + MAP_NOCACHE); + void __iomem *rregs = map_physmem(AR71XX_RESET_BASE, AR71XX_RESET_SIZE, + MAP_NOCACHE); + const u32 mask = QCA956X_RESET_SGMII_ASSERT | QCA956X_RESET_SGMII; + + writel(BIT(2) | BIT(0), pregs + QCA956X_PLL_ETH_SGMII_SERDES_REG); + + reg = readl(gregs + QCA956X_GMAC_REG_SGMII_SERDES); + vco_fast = SGMII_SERDES_VCO_FAST_GET(reg); + vco_slow = SGMII_SERDES_VCO_SLOW_GET(reg); + + /* Set resistor calibration from 0000 to 1111 */ + for (i = 0; i < 0x10; i++) { + reg = (readl(gregs + QCA956X_GMAC_REG_SGMII_SERDES) & + ~SGMII_SERDES_RES_CALIBRATION_MASK) | + SGMII_SERDES_RES_CALIBRATION_SET(i); + writel(reg, gregs + QCA956X_GMAC_REG_SGMII_SERDES); + + udelay(50); + + reg = readl(gregs + QCA956X_GMAC_REG_SGMII_SERDES); + if (vco_fast != SGMII_SERDES_VCO_FAST_GET(reg) || + vco_slow != SGMII_SERDES_VCO_SLOW_GET(reg)) { + if (start_val == 0) { + start_val = i; + end_val = i; + } else { + end_val = i; + } + } + vco_fast = SGMII_SERDES_VCO_FAST_GET(reg); + vco_slow = SGMII_SERDES_VCO_SLOW_GET(reg); + } + + if (start_val == 0) + rev_sgmii_val = 0x7; + else + rev_sgmii_val = (start_val + end_val) >> 1; + + writel((readl(gregs + QCA956X_GMAC_REG_SGMII_SERDES) & + ~SGMII_SERDES_RES_CALIBRATION_MASK) | + SGMII_SERDES_RES_CALIBRATION_SET(rev_sgmii_val), + gregs + QCA956X_GMAC_REG_SGMII_SERDES); + + writel(BIT(2) | BIT(0), pregs + QCA956X_PLL_ETH_SGMII_SERDES_REG); + + reg = readl(gregs + QCA956X_GMAC_REG_SGMII_SERDES); + writel(SGMII_SERDES_CDR_BW_SET(3) | SGMII_SERDES_TX_DR_CTRL_SET(1) | + SGMII_SERDES_PLL_BW_SET(1) | SGMII_SERDES_EN_SIGNAL_DETECT_SET(1) | + SGMII_SERDES_FIBER_SDO_SET(1) | SGMII_SERDES_VCO_REG_SET(3) | reg, + gregs + QCA956X_GMAC_REG_SGMII_SERDES); + + setbits_be32(rregs + QCA956X_RESET_REG_RESET_MODULE, mask); + mdelay(1); + clrbits_be32(rregs + QCA956X_RESET_REG_RESET_MODULE, mask); + mdelay(1); + + while (!(readl(gregs + QCA956X_GMAC_REG_SGMII_SERDES) & BIT(15))) + /* NOP */; + + return 0; +} + +static int qca956x_sgmii_setup(void) +{ + int i; + u32 s = 0, reg = 0; + u32 _regs[] = { + BIT(4), /* HW_RX_125M_N */ + BIT(2), /* RX_125M_N */ + BIT(3), /* TX_125M_N */ + BIT(0), /* RX_CLK_N */ + BIT(1), /* TX_CLK_N */ + }; + void __iomem *gregs = map_physmem(AR71XX_MII_BASE, AR71XX_MII_SIZE, + MAP_NOCACHE); + + /* Force sgmii mode */ + writel(BIT(6) | BIT(15) | BIT(8), gregs + QCA956X_GMAC_REG_MR_AN_CTRL); + udelay(10); + writel(0x2 | BIT(5) | (0x2 << 6), gregs + QCA956X_GMAC_REG_SGMII_CONFIG); + + /* SGMII reset sequence sugguest by qca systems team. */ + writel(0, gregs + QCA956X_GMAC_REG_SGMII_RESET); + for (i = 0; i < ARRAY_SIZE(_regs); i++) { + reg |= _regs[i]; + writel(reg, gregs + QCA956X_GMAC_REG_SGMII_RESET); + } + + writel(readl(gregs + QCA956X_GMAC_REG_MR_AN_CTRL) & ~BIT(15), + gregs + QCA956X_GMAC_REG_MR_AN_CTRL); + + /* + * WARNING: Across resets SGMII link status goes to weird state. + * if 0xb8070058 (SGMII_DEBUG Register) reads other than 0xf or 0x10 + * for sure we are in bad state. + * Issue a PHY RESET in MR_AN_CONTROL_ADDRESS to keep going. + */ + i = 0; + s = (readl(gregs + QCA956X_GMAC_REG_SGMII_DEBUG) & 0xff); + while (!(s == 0xf || s == 0x10)) { + writel(readl(gregs + QCA956X_GMAC_REG_MR_AN_CTRL) | BIT(15), + gregs + QCA956X_GMAC_REG_MR_AN_CTRL); + udelay(100); + writel(readl(gregs + QCA956X_GMAC_REG_MR_AN_CTRL) & ~BIT(15), + gregs + QCA956X_GMAC_REG_MR_AN_CTRL); + if (i++ == 10) + break; + s = (readl(gregs + QCA956X_GMAC_REG_SGMII_DEBUG) & 0xff); + } + + return 0; +} + +static int qca956x_s17_reset(void) +{ + void __iomem *regs = map_physmem(AR71XX_GPIO_BASE, AR71XX_GPIO_SIZE, + MAP_NOCACHE); + void __iomem *rregs = map_physmem(AR71XX_RESET_BASE, AR71XX_RESET_SIZE, + MAP_NOCACHE); + const u32 mask = QCA956X_RESET_SGMII_ASSERT | QCA956X_RESET_SGMII | + QCA956X_RESET_EXTERNAL | QCA956X_RESET_SGMII_ANALOG | + QCA956X_RESET_SWITCH; + /* Bits(Reserved in datasheet) should be set to 1 */ + const u32 mask_r = QCA956X_RESET_SGMII_ASSERT | QCA956X_RESET_SGMII | + QCA956X_RESET_EXTERNAL; + + setbits_be32(rregs + QCA956X_RESET_REG_RESET_MODULE, mask); + mdelay(1); + clrbits_be32(rregs + QCA956X_RESET_REG_RESET_MODULE, mask_r); + mdelay(1); + + /* Reset s17 switch(GPIO11) SYS_RST_L */ + writel(readl(regs + AR71XX_GPIO_REG_OE) & ~BIT(11), + regs + AR71XX_GPIO_REG_OE); + udelay(100); + + writel(readl(regs + AR71XX_GPIO_REG_OUT) & ~BIT(11), + regs + AR71XX_GPIO_REG_OUT); + udelay(100); + writel(readl(regs + AR71XX_GPIO_REG_OUT) | BIT(11), + regs + AR71XX_GPIO_REG_OUT); + + return 0; +} + +static int qca956x_init_mdio(void) +{ + u32 reg; + void __iomem *regs = map_physmem(AR71XX_GPIO_BASE, AR71XX_GPIO_SIZE, + MAP_NOCACHE); + void __iomem *rregs = map_physmem(AR71XX_RESET_BASE, AR71XX_RESET_SIZE, + MAP_NOCACHE); + const u32 mask = QCA956X_RESET_GE0_MDIO | QCA956X_RESET_GE0_MAC | + QCA956X_RESET_GE1_MDIO | QCA956X_RESET_GE1_MAC; + + setbits_be32(rregs + QCA956X_RESET_REG_RESET_MODULE, mask); + mdelay(1); + clrbits_be32(rregs + QCA956X_RESET_REG_RESET_MODULE, mask); + mdelay(1); + + /* GPIO4 as MDI */ + reg = readl(regs + QCA956X_GPIO_REG_IN_ENABLE3); + reg &= ~(0xff << 16); + reg |= (0x4 << 16); + writel(reg, regs + QCA956X_GPIO_REG_IN_ENABLE3); + + /* GPIO4 as MDO */ + reg = readl(regs + QCA956X_GPIO_REG_OUT_FUNC1); + reg &= ~0xff; + reg |= 0x20; + writel(reg, regs + QCA956X_GPIO_REG_OUT_FUNC1); + + /* Init MDC(GPIO3) / MDIO(GPIO4) */ + reg = readl(regs + AR71XX_GPIO_REG_OE); + reg &= ~BIT(4); + writel(reg, regs + AR71XX_GPIO_REG_OE); + udelay(100); + + reg = readl(regs + AR71XX_GPIO_REG_OE); + reg &= ~BIT(3); + writel(reg, regs + AR71XX_GPIO_REG_OE); + udelay(100); + + /* GPIO3 as MDI */ + reg = readl(regs + QCA956X_GPIO_REG_OUT_FUNC0); + reg &= ~(0xff << 24); + reg |= (0x21 << 24); + writel(reg, regs + QCA956X_GPIO_REG_OUT_FUNC0); + + return 0; +} + +static int eth_init_qca956x(void) +{ + void __iomem *pregs = map_physmem(AR71XX_PLL_BASE, AR71XX_PLL_SIZE, + MAP_NOCACHE); + void __iomem *gregs = map_physmem(AR71XX_MII_BASE, AR71XX_MII_SIZE, + MAP_NOCACHE); + + qca956x_sgmii_cal(); + qca956x_s17_reset(); + qca956x_init_mdio(); + + if (ath79_get_bootstrap() & QCA956X_BOOTSTRAP_REF_CLK_40) + writel(0x45500, pregs + QCA956X_PLL_SWITCH_CLK_CTRL_REG); + else + writel(0xc5200, pregs + QCA956X_PLL_SWITCH_CLK_CTRL_REG); + + qca956x_sgmii_setup(); + + writel((3 << 16) | (3 << 14) | (1 << 0) | (1 << 6), + gregs + QCA956X_GMAC_REG_ETH_CFG); + + writel((1 << 31) | (2 << 28) | (2 << 26) | (1 << 25), + pregs + QCA956X_PLL_ETH_XMII_CTRL_REG); + mdelay(1); + + return 0; +} + int ath79_eth_reset(void) { /* @@ -164,6 +433,8 @@ int ath79_eth_reset(void) return eth_init_ar934x(); if (soc_is_qca953x()) return eth_init_qca953x(); + if (soc_is_qca956x()) + return eth_init_qca956x(); return -EINVAL; } diff --git a/board/qca/ap152/Kconfig b/board/qca/ap152/Kconfig new file mode 100644 index 0000000000..f6ad498e85 --- /dev/null +++ b/board/qca/ap152/Kconfig @@ -0,0 +1,15 @@ +if TARGET_AP152 + +config SYS_VENDOR + default "qca" + +config SYS_BOARD + default "ap152" + +config SYS_CONFIG_NAME + default "ap152" + +config SYS_TEXT_BASE + default 0x9f000000 + +endif diff --git a/board/qca/ap152/MAINTAINERS b/board/qca/ap152/MAINTAINERS new file mode 100644 index 0000000000..785ec2766d --- /dev/null +++ b/board/qca/ap152/MAINTAINERS @@ -0,0 +1,6 @@ +AP152 BOARD +M: Rosy Song <rosysong(a)rosinson.com> +S: Maintained +F: board/qca/ap152/ +F: include/configs/ap152.h +F: configs/ap152_defconfig diff --git a/board/qca/ap152/Makefile b/board/qca/ap152/Makefile new file mode 100644 index 0000000000..4270afa129 --- /dev/null +++ b/board/qca/ap152/Makefile @@ -0,0 +1,3 @@ +# SPDX-License-Identifier: GPL-2.0+ + +obj-y = ap152.o diff --git a/board/qca/ap152/ap152.c b/board/qca/ap152/ap152.c new file mode 100644 index 0000000000..30cd56563b --- /dev/null +++ b/board/qca/ap152/ap152.c @@ -0,0 +1,81 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 Rosy Song <rosysong(a)rosinson.com> + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/addrspace.h> +#include <asm/types.h> +#include <mach/ar71xx_regs.h> +#include <mach/ddr.h> +#include <mach/ath79.h> +#include <debug_uart.h> + +#define RST_RESET_RTC_RESET_LSB 27 +#define RST_RESET_RTC_RESET_MASK 0x08000000 +#define RST_RESET_RTC_RESET_SET(x) \ + (((x) << RST_RESET_RTC_RESET_LSB) & RST_RESET_RTC_RESET_MASK) + +#ifdef CONFIG_DEBUG_UART_BOARD_INIT +void board_debug_uart_init(void) +{ + void __iomem *regs; + u32 val; + + regs = map_physmem(AR71XX_GPIO_BASE, AR71XX_GPIO_SIZE, + MAP_NOCACHE); + + /* UART : RX18, TX22 done + * GPIO18 as input, GPIO22 as output + */ + val = readl(regs + AR71XX_GPIO_REG_OE); + val |= QCA956X_GPIO(18); + val &= ~QCA956X_GPIO(22); + writel(val, regs + AR71XX_GPIO_REG_OE); + + /* + * Enable GPIO22 as UART0_SOUT + */ + val = readl(regs + QCA956X_GPIO_REG_OUT_FUNC5); + val &= ~QCA956X_GPIO_MUX_MASK(16); + val |= QCA956X_GPIO_OUT_MUX_UART0_SOUT << 16; + writel(val, regs + QCA956X_GPIO_REG_OUT_FUNC5); + + /* + * Enable GPIO18 as UART0_SIN + */ + val = readl(regs + QCA956X_GPIO_REG_IN_ENABLE0); + val &= ~QCA956X_GPIO_MUX_MASK(8); + val |= QCA956X_GPIO_IN_MUX_UART0_SIN << 8; + writel(val, regs + QCA956X_GPIO_REG_IN_ENABLE0); + + /* + * Enable GPIO22 output + */ + val = readl(regs + AR71XX_GPIO_REG_OUT); + val |= QCA956X_GPIO(22); + writel(val, regs + AR71XX_GPIO_REG_OUT); +} +#endif + +int board_early_init_f(void) +{ + u32 reg; + void __iomem *rst_regs = map_physmem(AR71XX_RESET_BASE, + AR71XX_RESET_SIZE, MAP_NOCACHE); + +#ifndef CONFIG_SKIP_LOWLEVEL_INIT + /* CPU:775, DDR:650, AHB:258 */ + qca956x_pll_init(); + qca956x_ddr_init(); +#endif + + /* Take WMAC out of reset */ + reg = readl(rst_regs + QCA956X_RESET_REG_RESET_MODULE); + reg &= (~RST_RESET_RTC_RESET_SET(1)); + writel(reg, rst_regs + QCA956X_RESET_REG_RESET_MODULE); + + ath79_eth_reset(); + return 0; +} diff --git a/configs/ap152_defconfig b/configs/ap152_defconfig new file mode 100644 index 0000000000..21cb6eb742 --- /dev/null +++ b/configs/ap152_defconfig @@ -0,0 +1,49 @@ +CONFIG_MIPS=y +CONFIG_SYS_TEXT_BASE=0x9F000000 +CONFIG_SYS_MALLOC_F_LEN=0x800 +CONFIG_SYS_CACHE_SIZE_AUTO=y +CONFIG_DEBUG_UART_BOARD_INIT=y +CONFIG_DEBUG_UART_BASE=0xb8020000 +CONFIG_DEBUG_UART_CLOCK=25000000 +CONFIG_ARCH_ATH79=y +CONFIG_TARGET_AP152=y +CONFIG_DEBUG_UART=y +CONFIG_BOOTDELAY=3 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=squashfs" +CONFIG_DISPLAY_CPUINFO=y +CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_SYS_PROMPT="ap152 # " +# CONFIG_CMD_BDI is not set +# CONFIG_CMD_CONSOLE is not set +# CONFIG_CMD_ELF is not set +# CONFIG_CMD_XIMG is not set +# CONFIG_CMD_EXPORTENV is not set +# CONFIG_CMD_IMPORTENV is not set +# CONFIG_CMD_EDITENV is not set +# CONFIG_CMD_CRC32 is not set +CONFIG_CMD_MEMTEST=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_SF=y +CONFIG_CMD_SPI=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nor0=spi-flash.0" +CONFIG_MTDPARTS_DEFAULT="mtdparts=spi-flash.0:256k(u-boot),64k(u-boot-env),6336k(rootfs),1472k(uImage),64k(ART)" +# CONFIG_ISO_PARTITION is not set +CONFIG_DEFAULT_DEVICE_TREE="ap152" +CONFIG_ENV_IS_IN_SPI_FLASH=y +# CONFIG_NET is not set +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_BAR=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_DATAFLASH=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_PINCTRL=y +CONFIG_DM_SERIAL=y +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_ATH79_SPI=y +CONFIG_LZMA=y diff --git a/include/configs/ap152.h b/include/configs/ap152.h new file mode 100644 index 0000000000..bc88506dff --- /dev/null +++ b/include/configs/ap152.h @@ -0,0 +1,54 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2018 Rosy Song <rosysong(a)rosinson.com> + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_MHZ 375 +#define CONFIG_SYS_MIPS_TIMER_FREQ (CONFIG_SYS_MHZ * 1000000) + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#define CONFIG_SYS_MALLOC_LEN 0x40000 +#define CONFIG_SYS_BOOTPARAMS_LEN 0x20000 + +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_LOAD_ADDR 0x81000000 + +#define CONFIG_SYS_INIT_RAM_ADDR 0xbd000000 +#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE - 1) + +/* + * Serial Port + */ +#define CONFIG_SYS_NS16550_CLK 25000000 +#define CONFIG_SYS_BAUDRATE_TABLE \ + {9600, 19200, 38400, 57600, 115200} + +#define CONFIG_BOOTCOMMAND "sf probe;" \ + "mtdparts default;" \ + "bootm 0x9f060000" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "ipaddr=192.168.1.1\0" \ + "serverip=192.168.1.10\0" \ + +#define CONFIG_ENV_SPI_MAX_HZ 25000000 +#define CONFIG_ENV_OFFSET 0x40000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#define CONFIG_ENV_SIZE 0x10000 + +/* Miscellaneous configurable options */ + +/* + * Diagnostics + */ +#define CONFIG_SYS_MEMTEST_START 0x80100000 +#define CONFIG_SYS_MEMTEST_END 0x83f00000 + +#endif /* __CONFIG_H */ -- 2.17.1

2 1

[U-Boot] i.MX8MQ: u-boot-spl-ddr.bin not found
by Fabio Estevam 07 Mar '19

07 Mar '19

Hi, I am not able to build top of tree U-Boot for imx8mq-evk: WARNING './spl/u-boot-spl-ddr.bin' not found, resulting binary is not-functional make[1]: Nothing to be done for 'SPL'. CFGCHK u-boot.cfg It works fine when I build from u-boot-imx tree though. I have copied all the binaries to the U-Boot source as per the README. Does anyone have any ideas to fix the build for U-boot mainline? Thanks, Fabio Estevam

5 14

[U-Boot] [PATCH v2 0/4] Add network support for Jaguar2 SoCs
by Horatiu Vultur 07 Mar '19

07 Mar '19

This patch series add network support for Jaguar2 SoCs family. There are following pcb: Jaguar2-24(110), Jaguar2-48(pcb111) and Serval2(pcb112). v2-changes: - create serdes6g_setup and serdes1g_setup functions to be easier to extand for future boards. Horatiu Vultur (4): net: Add MSCC Jaguar2 network driver. board: mscc: jr2: Update MSCC Jaguar2 boards net: mscc: jaguar2: Add ethenet nodes for Jaguar2. configs: mscc_jr2: Add network support arch/mips/dts/jr2_pcb110.dts | 67 ++++ arch/mips/dts/jr2_pcb111.dts | 352 ++++++++++++++++ arch/mips/dts/mscc,jr2.dtsi | 106 +++++ arch/mips/dts/serval2_pcb112.dts | 39 ++ board/mscc/jr2/jr2.c | 443 ++++++++++++++++++++ configs/mscc_jr2_defconfig | 6 +- drivers/net/mscc_eswitch/Kconfig | 7 + drivers/net/mscc_eswitch/Makefile | 1 + drivers/net/mscc_eswitch/jr2_switch.c | 735 ++++++++++++++++++++++++++++++++++ include/configs/vcoreiii.h | 2 +- 10 files changed, 1756 insertions(+), 2 deletions(-) create mode 100644 drivers/net/mscc_eswitch/jr2_switch.c -- 2.7.4

1 4

[U-Boot] Pull request: u-boot-net.git master
by Joe Hershberger 07 Mar '19

07 Mar '19

Hi Tom, These patches passed the CI build here: https://travis-ci.org/jhershbe/u-boot/builds/501807294 The following changes since commit aff66f22d6eeb27c6329c0a3c1ebc52914c8affa: Merge tag 'mips-pull-2019-01-23' of git://git.denx.de/u-boot-mips (2019-01-23 17:24:31 -0500) are available in the git repository at: git://git.denx.de/u-boot-net.git master for you to fetch changes up to 91c9cbabf935b37ab6c0b9b622e7faf0b350acb6: net: phy: aquantia: Print information on config (2019-01-24 11:35:30 -0600) ---------------------------------------------------------------- Aditya Prayoga (1): net: mvneta: Add GPIO configuration support Andreas Pretzsch (1): net: phy: micrel: fix KSZ9031 clock skew for values greater 0ps Baruch Siach (2): net: mvpp2: fix lookup of mdio registers base address net: mvpp2: mdio device per port Carlo Caione (1): net: phy: realtek: Add functions to read PHY's extended registers Chris Packham (3): net: mvgbe: fallback phy-mode to GMII net: move ether_crc to tsec driver net: remove CONFIG_MCAST_TFTP Pankaj Bansal (1): net: phy: Add clause 45 identifier to phy_device Ramon Fried (1): net: macb: fix mapping of registers Simon Goldschmidt (4): net: designware: fix tx packet length net: designware: clear padding bytes net: remove duplicate definition of ETHADDR_WILDCARD net: fix env flags for eth10addr and above Thomas RIENOESSL (1): net: explicitly assign errno to return code in case of network failure Valentin-catalin Neacsu (2): net: phy: aquantia: Enable autoneg when on USXGMII net: phy: aquantia: Print information on config README | 9 -- drivers/net/designware.c | 18 ++-- drivers/net/macb.c | 4 +- drivers/net/mvgbe.c | 6 +- drivers/net/mvneta.c | 15 +++ drivers/net/mvpp2.c | 84 +++++++-------- drivers/net/phy/aquantia.c | 39 +++++++ drivers/net/phy/micrel_ksz90x1.c | 4 +- drivers/net/phy/phy.c | 15 ++- drivers/net/phy/realtek.c | 29 ++++++ drivers/net/rtl8139.c | 6 +- drivers/net/tsec.c | 37 +++++-- drivers/usb/gadget/ether.c | 3 - include/env_callback.h | 2 - include/env_flags.h | 2 +- include/net.h | 15 +-- include/phy.h | 1 + net/eth-uclass.c | 2 - net/eth_legacy.c | 28 ----- net/net.c | 8 +- net/tftp.c | 219 --------------------------------------- scripts/config_whitelist.txt | 1 - test/dm/eth.c | 2 +- 23 files changed, 184 insertions(+), 365 deletions(-) Thanks! -Joe

2 1

[U-Boot] Pull request: u-boot-spi/master
by Jagan Teki 07 Mar '19

07 Mar '19

Hi Tom, Please pull this PR. Summary: - dw spi include file fix - Allwinner A31 spi, been in ML in many releases. thanks, Jagan. The following changes since commit cfba74d0bef350d81241b059180bcc5a1e93bdfa: Merge branch 'master' of git://git.denx.de/u-boot-socfpga (2019-02-28 18:57:32 -0500) are available in the Git repository at: git://git.denx.de/u-boot-spi.git master for you to fetch changes up to a51cd54eff284ee42bfc1b74b8581daec78496f6: spi: Rename sun4i_spi.c into spi-sunxi.c (2019-03-04 18:08:56 +0530) ---------------------------------------------------------------- Horatiu.Vultur(a)microchip.com (1): spi: designware: Change include order Jagan Teki (9): spi: sun4i: Poll for rxfifo to be filled up clk: sunxi: Implement SPI clocks, resets spi: sun4i: Simplify reg writes using set/clrbits_le32 spi: sun4i: Access registers and bits via enum offsets spi: sun4i: Support fifo_depth via drvdata spi: sun4i: Add CLK support spi: sun4: Add A31 spi controller support spi: sun4i: Driver cleanup spi: Rename sun4i_spi.c into spi-sunxi.c drivers/clk/sunxi/clk_a10.c | 10 + drivers/clk/sunxi/clk_a10s.c | 7 + drivers/clk/sunxi/clk_a23.c | 7 + drivers/clk/sunxi/clk_a31.c | 13 + drivers/clk/sunxi/clk_a64.c | 7 + drivers/clk/sunxi/clk_a80.c | 13 + drivers/clk/sunxi/clk_a83t.c | 7 + drivers/clk/sunxi/clk_h3.c | 7 + drivers/clk/sunxi/clk_h6.c | 9 + drivers/clk/sunxi/clk_r40.c | 13 + drivers/clk/sunxi/clk_v3s.c | 4 + drivers/spi/Kconfig | 12 +- drivers/spi/Makefile | 2 +- drivers/spi/designware_spi.c | 2 +- drivers/spi/{sun4i_spi.c => spi-sunxi.c} | 445 +++++++++++++++++++++---------- 15 files changed, 417 insertions(+), 141 deletions(-) rename drivers/spi/{sun4i_spi.c => spi-sunxi.c} (50%)

2 1

[U-Boot] PULL request for the UEFI subsystem for v2019.04-rc4
by Heinrich Schuchardt 07 Mar '19

07 Mar '19

The following changes since commit cfba74d0bef350d81241b059180bcc5a1e93bdfa: Merge branch 'master' of git://git.denx.de/u-boot-socfpga (2019-02-28 18:57:32 -0500) are available in the Git repository at: https://github.com/xypron2/u-boot.git efi-2019-04-rc4 for you to fetch changes up to 1a9fce50393d2e7b7c3adb70764ab22a9267d815: efi_loader: HII protocols: debug messages (2019-03-02 23:34:26 +0100) Primary key fingerprint: 6DC4 F9C7 1F29 A6FA 06B7 6D33 C481 DBBC 2C05 1AC4 This pull request contains only bug fixes. The most notable bug fixed was writing to random memory addresses when trying to add a HII package of a yet unsupported package type. Travis report: https://travis-ci.org/xypron2/u-boot/builds/500934600 ---------------------------------------------------------------- Heinrich Schuchardt (4): efi_loader: do not add \ in efi_fs_from_name() efi_loader: HII protocols: fix new_package_list() efi_loader: error handling for `efidebug boot add` efi_loader: HII protocols: debug messages cmd/efidebug.c | 2 +- lib/efi_loader/efi_device_path.c | 7 +------ lib/efi_loader/efi_hii.c | 38 +++++++++++++++++++------------------- 3 files changed, 21 insertions(+), 26 deletions(-)

2 1

[U-Boot] [PATCH 1/2] ddr: socfpga: Fix IO in Arria10 DDR driver
by Marek Vasut 07 Mar '19

07 Mar '19

The Altera Arria10 DDR driver was using constants in a few places instead of reading registers associated with those constants, fix this. Signed-off-by: Marek Vasut <marex(a)denx.de> Cc: Chin Liang See <chin.liang.see(a)intel.com> Cc: Dinh Nguyen <dinguyen(a)kernel.org> Cc: Simon Goldschmidt <simon.k.r.goldschmidt(a)gmail.com> Cc: Tien Fong Chee <tien.fong.chee(a)intel.com> --- drivers/ddr/altera/sdram_arria10.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/ddr/altera/sdram_arria10.c b/drivers/ddr/altera/sdram_arria10.c index 29ea7492f3..6724eb29f1 100644 --- a/drivers/ddr/altera/sdram_arria10.c +++ b/drivers/ddr/altera/sdram_arria10.c @@ -304,7 +304,7 @@ static void sdram_mmr_init(void) * bit[9:6] = Minor Release # * bit[14:10] = Major Release # */ - if ((socfpga_io48_mmr_base->niosreserve1 >> 6) & 0x1FF) { + if ((readl(&socfpga_io48_mmr_base->niosreserve1) >> 6) & 0x1FF) { update_value = readl(&socfpga_io48_mmr_base->niosreserve0); writel(((update_value & 0xFF) >> 5), &socfpga_ecc_hmc_base->ddrioctrl); @@ -394,7 +394,7 @@ static void sdram_mmr_init(void) caltim0_cfg_act_to_rdwr - (ctrlcfg0_cfg_ctrl_burst_len >> 2)); - io48_value = ((((socfpga_io48_mmr_base->dramtiming0 & + io48_value = ((((readl(&socfpga_io48_mmr_base->dramtiming0) & ALT_IO48_DRAMTIME_MEM_READ_LATENCY_MASK) + 2 + 15 + (ctrlcfg0_cfg_ctrl_burst_len >> 1)) >> 1) - /* Up to here was in memory cycles so divide by 2 */ @@ -424,7 +424,7 @@ static void sdram_mmr_init(void) &socfpga_noc_ddr_scheduler_base->ddr_t_main_scheduler_ddrmode); /* Configure the read latency [0xFFD12414] */ - writel(((socfpga_io48_mmr_base->dramtiming0 & + writel(((readl(&socfpga_io48_mmr_base->dramtiming0) & ALT_IO48_DRAMTIME_MEM_READ_LATENCY_MASK) >> 1) + DDR_READ_LATENCY_DELAY, &socfpga_noc_ddr_scheduler_base-> -- 2.20.1

3 5

[U-Boot] [PATCH 1/6] pico-imx6ul: Import dts files from kernel
by Fabio Estevam 07 Mar '19

07 Mar '19

Import the device tree files from kernel 5.0-rc6 in preparation for driver model conversion. Signed-off-by: Fabio Estevam <festevam(a)gmail.com> --- arch/arm/dts/imx6ul-pico-hobbit.dts | 100 ++++++ arch/arm/dts/imx6ul-pico-pi.dts | 97 ++++++ arch/arm/dts/imx6ul-pico.dtsi | 461 ++++++++++++++++++++++++++++ 3 files changed, 658 insertions(+) create mode 100644 arch/arm/dts/imx6ul-pico-hobbit.dts create mode 100644 arch/arm/dts/imx6ul-pico-pi.dts create mode 100644 arch/arm/dts/imx6ul-pico.dtsi diff --git a/arch/arm/dts/imx6ul-pico-hobbit.dts b/arch/arm/dts/imx6ul-pico-hobbit.dts new file mode 100644 index 0000000000..39eeeddac3 --- /dev/null +++ b/arch/arm/dts/imx6ul-pico-hobbit.dts @@ -0,0 +1,100 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +// +// Copyright 2015 Technexion Ltd. +// +// Author: Wig Cheng <wig.cheng(a)technexion.com> +// Richard Hu <richard.hu(a)technexion.com> +// Tapani Utriainen <tapani(a)technexion.com> +/dts-v1/; + +#include "imx6ul-pico.dtsi" +/ { + model = "TechNexion PICO-IMX6UL and HOBBIT baseboard"; + compatible = "technexion,imx6ul-pico-hobbit", "fsl,imx6ul"; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + led { + label = "gpio-led"; + gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; + }; + }; + + sound { + compatible = "fsl,imx-audio-sgtl5000"; + model = "imx6ul-sgtl5000"; + audio-cpu = <&sai1>; + audio-codec = <&sgtl5000>; + audio-routing = + "LINE_IN", "Line In Jack", + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + }; + + sys_mclk: clock-sys-mclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24576000>; + }; +}; + +&i2c2 { + clock_frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + sgtl5000: codec@a { + reg = <0x0a>; + compatible = "fsl,sgtl5000"; + clocks = <&sys_mclk>; + VDDA-supply = <&reg_2p5v>; + VDDIO-supply = <&reg_3p3v>; + }; +}; + +&i2c3 { + status = "okay"; + + polytouch: touchscreen@38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + interrupt-parent = <&gpio1>; + interrupts = <29 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>; + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + }; + + adc081c: adc@50 { + compatible = "ti,adc081c"; + reg = <0x50>; + vref-supply = <&reg_3p3v>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + MX6UL_PAD_CSI_VSYNC__GPIO4_IO19 0x10b0 + MX6UL_PAD_CSI_DATA00__GPIO4_IO21 0x10b0 + MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x10b0 + MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x10b0 + MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x10b0 + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x10b0 + >; + }; + + pinctrl_gpio_leds: gpioledsgrp { + fsl,pins = < + MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x10b0 + >; + }; +}; diff --git a/arch/arm/dts/imx6ul-pico-pi.dts b/arch/arm/dts/imx6ul-pico-pi.dts new file mode 100644 index 0000000000..de07357b27 --- /dev/null +++ b/arch/arm/dts/imx6ul-pico-pi.dts @@ -0,0 +1,97 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +// +// Copyright 2015 Technexion Ltd. +// +// Author: Wig Cheng <wig.cheng(a)technexion.com> +// Richard Hu <richard.hu(a)technexion.com> +// Tapani Utriainen <tapani(a)technexion.com> +/dts-v1/; + +#include "imx6ul-pico.dtsi" +/ { + model = "TechNexion PICO-IMX6UL and PI baseboard"; + compatible = "technexion,imx6ul-pico-pi", "fsl,imx6ul"; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + led { + label = "gpio-led"; + gpios = <&gpio4 20 GPIO_ACTIVE_HIGH>; + }; + }; + + sound { + compatible = "fsl,imx-audio-sgtl5000"; + model = "imx6ul-sgtl5000"; + audio-cpu = <&sai1>; + audio-codec = <&sgtl5000>; + audio-routing = + "LINE_IN", "Line In Jack", + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + }; + + sys_mclk: clock-sys-mclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24576000>; + }; +}; + +&i2c2 { + clock_frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + sgtl5000: codec@a { + reg = <0x0a>; + compatible = "fsl,sgtl5000"; + clocks = <&sys_mclk>; + VDDA-supply = <&reg_2p5v>; + VDDIO-supply = <&reg_3p3v>; + }; +}; + +&i2c3 { + clock_frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + polytouch: touchscreen@38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + interrupt-parent = <&gpio1>; + interrupts = <29 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>; + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + MX6UL_PAD_CSI_VSYNC__GPIO4_IO19 0x10b0 + MX6UL_PAD_CSI_DATA00__GPIO4_IO21 0x10b0 + MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x10b0 + MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x10b0 + MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x10b0 + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x10b0 + >; + }; + + pinctrl_gpio_leds: gpioledsgrp { + fsl,pins = < + MX6UL_PAD_CSI_HSYNC__GPIO4_IO20 0x10b0 + >; + }; +}; diff --git a/arch/arm/dts/imx6ul-pico.dtsi b/arch/arm/dts/imx6ul-pico.dtsi new file mode 100644 index 0000000000..de9f83189b --- /dev/null +++ b/arch/arm/dts/imx6ul-pico.dtsi @@ -0,0 +1,461 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +// +// Copyright 2015 Technexion Ltd. +// +// Author: Wig Cheng <wig.cheng(a)technexion.com> +// Richard Hu <richard.hu(a)technexion.com> +// Tapani Utriainen <tapani(a)technexion.com> +/dts-v1/; + +#include "imx6ul.dtsi" + +/ { + /* Will be filled by the bootloader */ + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0>; + }; + + chosen { + stdout-path = &uart6; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm3 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + status = "okay"; + }; + + reg_2p5v: regulator-2p5v { + compatible = "regulator-fixed"; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_sd1_vmmc: regulator-sd1-vmmc { + compatible = "regulator-fixed"; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_otg_vbus: regulator-usb-otg-vbus { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg1>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 6 0>; + }; + + reg_brcm: regulator-brcm { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_brcm_reg>; + regulator-name = "brcm_reg"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <200000>; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + status = "okay"; +}; + +&clks { + assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>; + assigned-clock-rates = <786432000>; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2>; + phy-mode = "rmii"; + phy-handle = <&ethphy1>; + status = "okay"; + phy-reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>; + phy-reset-duration = <1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + max-speed = <100>; + interrupt-parent = <&gpio5>; + interrupts = <6 IRQ_TYPE_LEVEL_LOW>; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic: pfuze3000@8 { + compatible = "fsl,pfuze3000"; + reg = <0x08>; + + regulators { + /* VDD_ARM_SOC_IN*/ + sw1b_reg: sw1b { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1475000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + /* DRAM */ + sw3a_reg: sw3 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1650000>; + regulator-boot-on; + regulator-always-on; + }; + + /* DRAM */ + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&lcdif { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcdif_dat &pinctrl_lcdif_ctrl>; + display = <&display0>; + status = "okay"; + + display0: display0 { + bits-per-pixel = <32>; + bus-width = <24>; + + display-timings { + native-mode = <&timing0>; + + timing0: timing0 { + clock-frequency = <33200000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <210>; + hback-porch = <46>; + hsync-len = <1>; + vback-porch = <22>; + vfront-porch = <23>; + vsync-len = <1>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "okay"; +}; + +&pwm7 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm7>; + status = "okay"; +}; + +&pwm8 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm8>; + status = "okay"; +}; + +&sai1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai1>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + uart-has-rtscts; + status = "okay"; +}; + +&uart6 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart6>; + status = "okay"; +}; + +&usbotg1 { + vbus-supply = <&reg_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg1_id>; + dr_mode = "otg"; + disable-over-current; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + bus-width = <8>; + no-1-8-v; + non-removable; + keep-power-in-suspend; + status = "okay"; +}; + +&usdhc2 { /* Wifi SDIO */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + no-1-8-v; + non-removable; + keep-power-in-suspend; + wakeup-source; + vmmc-supply = <&reg_brcm>; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; +}; + +&iomuxc { + pinctrl_brcm_reg: brcmreggrp { + fsl,pins = < + MX6UL_PAD_NAND_DATA06__GPIO4_IO08 0x10b0 /* WL_REG_ON */ + MX6UL_PAD_NAND_DATA04__GPIO4_IO06 0x10b0 /* WL_HOST_WAKE */ + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6UL_PAD_ENET1_TX_DATA1__ENET2_MDIO 0x1b0b0 + MX6UL_PAD_ENET1_TX_EN__ENET2_MDC 0x1b0b0 + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0 + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031 + MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x800 + MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x79 + >; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + MX6UL_PAD_ENET1_RX_DATA0__FLEXCAN1_TX 0x1b020 + MX6UL_PAD_ENET1_RX_DATA1__FLEXCAN1_RX 0x1b020 + >; + }; + + pinctrl_flexcan2: flexcan2grp { + fsl,pins = < + MX6UL_PAD_ENET1_TX_DATA0__FLEXCAN2_RX 0x1b020 + MX6UL_PAD_ENET1_RX_EN__FLEXCAN2_TX 0x1b020 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO02__I2C1_SCL 0x4001b8b0 + MX6UL_PAD_GPIO1_IO03__I2C1_SDA 0x4001b8b0 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0 + MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__I2C3_SCL 0x4001b8b0 + MX6UL_PAD_UART1_RX_DATA__I2C3_SDA 0x4001b8b0 + >; + }; + + pinctrl_lcdif_dat: lcdifdatgrp { + fsl,pins = < + MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79 + MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79 + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79 + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79 + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79 + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79 + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79 + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79 + MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79 + MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79 + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79 + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79 + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79 + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79 + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79 + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79 + MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79 + MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79 + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79 + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79 + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79 + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79 + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79 + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79 + >; + }; + + pinctrl_lcdif_ctrl: lcdifctrlgrp { + fsl,pins = < + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79 + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79 + MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79 + MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79 + /* LCD reset */ + MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x79 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6UL_PAD_NAND_ALE__PWM3_OUT 0x110b0 + >; + }; + + pinctrl_pwm7: pwm7grp { + fsl,pins = < + MX6UL_PAD_ENET1_TX_CLK__PWM7_OUT 0x110b0 + >; + }; + + pinctrl_pwm8: pwm8grp { + fsl,pins = < + MX6UL_PAD_ENET1_RX_ER__PWM8_OUT 0x110b0 + >; + }; + + pinctrl_sai1: sai1grp { + fsl,pins = < + MX6UL_PAD_CSI_DATA04__SAI1_TX_SYNC 0x1b0b0 + MX6UL_PAD_CSI_DATA05__SAI1_TX_BCLK 0x1b0b0 + MX6UL_PAD_CSI_DATA06__SAI1_RX_DATA 0x110b0 + MX6UL_PAD_CSI_DATA07__SAI1_TX_DATA 0x1f0b8 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b0 + MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b0 + MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b0 + MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b0 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO04__UART5_DCE_TX 0x1b0b1 + MX6UL_PAD_GPIO1_IO05__UART5_DCE_RX 0x1b0b1 + MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x1b0b1 + MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x1b0b1 + >; + }; + + pinctrl_uart6: uart6grp { + fsl,pins = < + MX6UL_PAD_CSI_MCLK__UART6_DCE_TX 0x1b0b1 + MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_usb_otg1: usbotg1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO06__GPIO1_IO06 0x10b0 + >; + }; + + pinctrl_usb_otg1_id: usbotg1idgrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10071 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059 + MX6UL_PAD_UART1_RTS_B__USDHC1_CD_B 0x03029 + MX6UL_PAD_NAND_READY_B__USDHC1_DATA4 0x17059 + MX6UL_PAD_NAND_CE0_B__USDHC1_DATA5 0x17059 + MX6UL_PAD_NAND_CE1_B__USDHC1_DATA6 0x17059 + MX6UL_PAD_NAND_CLE__USDHC1_DATA7 0x17059 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059 + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10059 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0 + >; + }; +}; -- 2.17.1

3 13