May 2016 - U-Boot

[U-Boot] [PATCH] mtd: nand: arasan_nfc: Correct nand ecc initialization
by Siva Durga Prasad Paladugu 25 May '16

25 May '16

Correct the nand ecc initialization code This fixes the issue of incorrect nand ecc init if no device is found in ecc_matrix then it endsup ecc init with junk initialization instead of the most suited one. Signed-off-by: Siva Durga Prasad Paladugu <sivadur(a)xilinx.com> --- drivers/mtd/nand/arasan_nfc.c | 18 +++++++++--------- 1 files changed, 9 insertions(+), 9 deletions(-) diff --git a/drivers/mtd/nand/arasan_nfc.c b/drivers/mtd/nand/arasan_nfc.c index 2d73a05..caa7982 100644 --- a/drivers/mtd/nand/arasan_nfc.c +++ b/drivers/mtd/nand/arasan_nfc.c @@ -1058,20 +1058,20 @@ static int arasan_nand_ecc_init(struct mtd_info *mtd) if (found < 0) return 1; - regval = ecc_matrix[i].eccaddr | - (ecc_matrix[i].eccsize << ARASAN_NAND_ECC_SIZE_SHIFT) | - (ecc_matrix[i].bch << ARASAN_NAND_ECC_BCH_SHIFT); + regval = ecc_matrix[found].eccaddr | + (ecc_matrix[found].eccsize << ARASAN_NAND_ECC_SIZE_SHIFT) | + (ecc_matrix[found].bch << ARASAN_NAND_ECC_BCH_SHIFT); writel(regval, &arasan_nand_base->ecc_reg); - if (ecc_matrix[i].bch) { + if (ecc_matrix[found].bch) { regval = readl(&arasan_nand_base->memadr_reg2); regval &= ~ARASAN_NAND_MEM_ADDR2_BCH_MASK; - regval |= (ecc_matrix[i].bchval << + regval |= (ecc_matrix[found].bchval << ARASAN_NAND_MEM_ADDR2_BCH_SHIFT); writel(regval, &arasan_nand_base->memadr_reg2); } - nand_oob.eccbytes = ecc_matrix[i].eccsize; + nand_oob.eccbytes = ecc_matrix[found].eccsize; eccpos_start = mtd->oobsize - nand_oob.eccbytes; for (i = 0; i < nand_oob.eccbytes; i++) @@ -1080,9 +1080,9 @@ static int arasan_nand_ecc_init(struct mtd_info *mtd) nand_oob.oobfree[0].offset = 2; nand_oob.oobfree[0].length = eccpos_start - 2; - nand_chip->ecc.size = ecc_matrix[i].ecc_codeword_size; - nand_chip->ecc.strength = ecc_matrix[i].eccbits; - nand_chip->ecc.bytes = ecc_matrix[i].eccsize; + nand_chip->ecc.size = ecc_matrix[found].ecc_codeword_size; + nand_chip->ecc.strength = ecc_matrix[found].eccbits; + nand_chip->ecc.bytes = ecc_matrix[found].eccsize; nand_chip->ecc.layout = &nand_oob; return 0; -- 1.7.1

2 1

[U-Boot] wanting to confirm i'm setting the MAC address the right way
by Robert P. J. Day 25 May '16

25 May '16

i want to use the fdt_fixup_ethernet() routine to automate most of the work of setting the MAC address in the FDT before passing it to the kernel, so here's what i'm about to do, and i'd appreciate someone saying, "yup, looks good" if it will indeed work. on either a MPC8280 or MPC8360 system, i will first set up the DTS file with some variation of: aliases { ethernet0 = &ucc0; }; ... snip ... ucc0:ucc@2000 { device_type = "network"; compatible = "ucc_geth"; model = "UCC"; device-id = <1>; reg = <0x2000 0x200>; interrupts = <0x20>; local-mac-address = [ 00 01 02 03 04 05 ]; rx-clock = <0x1c>; // CLK12 tx-clock = <0x1b>; // CLK11 phy-handle = <&PHY0>; }; at that point, given all the work done in fdt_fixup_ethernet(), i *think* that all i need to do in the board's ft_board_setup() routine is: eth_setenv_enetaddr("ethaddr", <physical addr of 6-byte MAC address>); is that about it? it *looks* like all i have to do, and fdt_fixup_etherhet() will do all the rest. rday -- ======================================================================== Robert P. J. Day Ottawa, Ontario, CANADA http://crashcourse.ca Twitter: http://twitter.com/rpjday LinkedIn: http://ca.linkedin.com/in/rpjday ========================================================================

2 2

[U-Boot] [PATCH v1] arm, am335x: siemens: enable DM/DTS support
by Heiko Schocher 25 May '16

25 May '16

enable basic DM/DTS support for the siemens am335x based boards. Signed-off-by: Heiko Schocher <hs(a)denx.de> --- This patchseries is based on the patches: [U-Boot,v1,1/7] siemens,am33x: add ubi fastmap support http://patchwork.ozlabs.org/patch/626008/ [U-Boot,v1,2/7] ubi: add new ubi command "ubi dettach" http://patchwork.ozlabs.org/patch/626010/ [U-Boot,v1,3/7] nand: add nand mtd concat support http://patchwork.ozlabs.org/patch/626009/ [U-Boot,v1,4/7] mtd: nand: omap: allow to switch to BCH16 http://patchwork.ozlabs.org/patch/626011/ [U-Boot,v1,5/7] am335x, dxr2: get ECC sType from I2C eeprom http://patchwork.ozlabs.org/patch/626012/ [U-Boot,v1,6/7] dfu, nand, ubi: fix erasing after write finish http://patchwork.ozlabs.org/patch/626013/ [U-Boot,v1,7/7] siemens,am33x: add draco etamin board http://patchwork.ozlabs.org/patch/626014/ arch/arm/Kconfig | 18 + arch/arm/dts/Makefile | 6 +- arch/arm/dts/am335x-draco.dts | 152 ++++++++ arch/arm/dts/am335x-draco.dtsi | 169 +++++++++ arch/arm/dts/am335x-pxm2.dtsi | 539 +++++++++++++++++++++++++++++ arch/arm/dts/am335x-pxm50.dts | 59 ++++ arch/arm/dts/am335x-rut.dts | 611 +++++++++++++++++++++++++++++++++ configs/draco_defconfig | 6 + configs/etamin_defconfig | 25 ++ configs/pxm2_defconfig | 6 + configs/rastaban_defconfig | 6 + configs/rut_defconfig | 6 + configs/thuban_defconfig | 6 + include/configs/siemens-am33x-common.h | 2 + 14 files changed, 1610 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/am335x-draco.dts create mode 100644 arch/arm/dts/am335x-draco.dtsi create mode 100644 arch/arm/dts/am335x-pxm2.dtsi create mode 100644 arch/arm/dts/am335x-pxm50.dts create mode 100644 arch/arm/dts/am335x-rut.dts diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index f72ce5c..6b98b72 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -328,31 +328,49 @@ config TARGET_DRACO bool "Support draco" select CPU_V7 select SUPPORT_SPL + select DM + select DM_SERIAL + select DM_GPIO config TARGET_THUBAN bool "Support thuban" select CPU_V7 select SUPPORT_SPL + select DM + select DM_SERIAL + select DM_GPIO config TARGET_RASTABAN bool "Support rastaban" select CPU_V7 select SUPPORT_SPL + select DM + select DM_SERIAL + select DM_GPIO config TARGET_ETAMIN bool "Support etamin" select CPU_V7 select SUPPORT_SPL + select DM + select DM_SERIAL + select DM_GPIO config TARGET_PXM2 bool "Support pxm2" select CPU_V7 select SUPPORT_SPL + select DM + select DM_SERIAL + select DM_GPIO config TARGET_RUT bool "Support rut" select CPU_V7 select SUPPORT_SPL + select DM + select DM_SERIAL + select DM_GPIO config TARGET_PENGWYN bool "Support pengwyn" diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index a75a485..3bfce04 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -90,7 +90,11 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += \ zynqmp-zc1751-xm015-dc1.dtb \ zynqmp-zc1751-xm016-dc2.dtb \ zynqmp-zc1751-xm019-dc5.dtb -dtb-$(CONFIG_AM33XX) += am335x-boneblack.dtb am335x-evm.dtb +dtb-$(CONFIG_AM33XX) += am335x-boneblack.dtb \ + am335x-draco.dtb \ + am335x-evm.dtb \ + am335x-pxm50.dtb \ + am335x-rut.dtb dtb-$(CONFIG_AM43XX) += am437x-gp-evm.dtb am437x-sk-evm.dtb dtb-$(CONFIG_THUNDERX) += thunderx-88xx.dtb diff --git a/arch/arm/dts/am335x-draco.dts b/arch/arm/dts/am335x-draco.dts new file mode 100644 index 0000000..25d0480 --- /dev/null +++ b/arch/arm/dts/am335x-draco.dts @@ -0,0 +1,152 @@ +/* + * Support for Siemens DRACO board + * + * Copyright (C) 2014 - Lukas Stockmann <lukas.stockmann(a)siemens.com> + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-draco.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Siemens DRACO"; + compatible = "siemens,draco", "ti,am33xx"; + + /* ethernet alias is needed for the MAC address passing from U-Boot */ + aliases { + ethernet0 = &cpsw_emac0; + mdio-gpio0 = &mdio0; + }; + + gpio-keys { + compatible = "gpio-keys"; + button0 { + label = "button0"; + gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; + linux,code = <KEY_F1>; /* button0 */ + }; + button1 { + label = "button1"; + gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + linux,code = <KEY_F2>; /* button1 */ + }; + }; + + ocp { + debugss: debugss@4b000000 { + compatible = "ti,debugss"; + ti,hwmods = "debugss"; + reg = <0x4b000000 1000000>; + status = "disabled"; + }; + }; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&gpio_mux_pins>; + + gpio_mux_pins: gpio_mux_pins { + pinctrl-single,pins = < + 0x1d0 (PIN_INPUT | MUX_MODE0) /* tms jtag */ + 0x1d4 (PIN_INPUT | MUX_MODE0) /* tdi jtag */ + 0x1d8 (PIN_OUTPUT | MUX_MODE0) /* tdo jtag */ + 0x1dc (PIN_INPUT | MUX_MODE0) /* tck jtag */ + 0x1e0 (PIN_INPUT | MUX_MODE0) /* trstn jtag */ + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + 0x0E8 (PIN_INPUT_PULLUP | MUX_MODE7) /* lcd_plck FIX STO should be a OUTPUT driven high*/ + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs_dv */ + 0x114 (PIN_OUTPUT | MUX_MODE1) /* mii1_txen.mii1_txen */ + 0x124 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd1.mii1_txd1 */ + 0x128 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd0.mii1_txd0 */ + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.mii1_rxd1 */ + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.mii1_rxd0 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + gpio_mdio_default: gpio_mdio_default { + pinctrl-single,pins = < + /* MDIO via GPIO */ + 0x148 (PIN_INPUT | MUX_MODE7) /* mdio_data.mdio_data GPIO0_0 */ + 0x14c (PIN_OUTPUT | MUX_MODE7) /* mdio_clk.mdio_clk GPIO0_1 */ + >; + }; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + slaves = <1>; /* use only one emac if */ + + mdio0: gpio { + compatible = "virtual,mdio-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_mdio_default>; + + #address-cells = <1>; + #size-cells = <0>; + gpios = <&gpio0 1 GPIO_ACTIVE_HIGH /* MDIO-CLK */ + &gpio0 0 GPIO_ACTIVE_HIGH>; /* MDIO-DATA */ + + phy0: ethernet-phy@1 { + reg = <0>; + }; + }; +}; + +/* Disable davinci/am335x mdio interface on this platform */ +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "disabled"; +}; + +&cpsw_emac0 { + phy_id = <&mdio0>, <0>; + phy-mode = "rmii"; +}; + +&phy_sel { + rmii-clock-ext; +}; diff --git a/arch/arm/dts/am335x-draco.dtsi b/arch/arm/dts/am335x-draco.dtsi new file mode 100644 index 0000000..b38ff55 --- /dev/null +++ b/arch/arm/dts/am335x-draco.dtsi @@ -0,0 +1,169 @@ +/* + * Common support for Siemens Draco SOM (AM335x based) + * + * Copyright (C) 2013,2014 - Stefan Roese <sr(a)denx.de> + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/ { + chosen { + stdout-path = &uart0; + tick-timer = &timer2; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x08000000>; /* 128 MB */ + }; + + ocp { + uart0: serial@44e09000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "okay"; + }; + + i2c0: i2c@44e0b000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + + eeprom: eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + pagesize = <64>; + }; + }; + + musb: usb@47400000 { + status = "okay"; + + control@44e10620 { + status = "okay"; + }; + + usb-phy@47401300 { + status = "okay"; + }; + + usb-phy@47401b00 { + status = "okay"; + }; + + usb@47401000 { + status = "okay"; + }; + + usb@47401800 { + status = "okay"; + dr_mode = "host"; + }; + + dma-controller@47402000 { + status = "okay"; + }; + }; + }; +}; + +&am33xx_pinmux { + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + nandflash_pins: nandflash_pins { + pinctrl-single,pins = < + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + >; + }; + }; + + +&timer3 { + status = "disabled"; +}; + +&uart4 { + status = "disabled"; +}; + +&elm { + status = "okay"; +}; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nandflash_pins>; + + ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ + + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + nand-bus-width = <8>; + ti,nand-ecc-opt = "bch8"; + gpmc,device-nand = "true"; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <40>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + + #address-cells = <1>; + #size-cells = <1>; + elm_id = <&elm>; + }; +}; + +/* disable the RTC node as its not accessible on the draco/dxr2 board */ +&rtc { + status = "disabled"; + ti,hwmods = "disabled"; +}; diff --git a/arch/arm/dts/am335x-pxm2.dtsi b/arch/arm/dts/am335x-pxm2.dtsi new file mode 100644 index 0000000..8d58cd4 --- /dev/null +++ b/arch/arm/dts/am335x-pxm2.dtsi @@ -0,0 +1,539 @@ +/* + * Copyright (C) 2014 DENX Software Engineering GmbH + * Heiko Schocher <hs(a)denx.de> + * + * Based on: + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "am33xx.dtsi" +#include <dt-bindings/input/input.h> + +/ { + chosen { + stdout-path = &uart0; + tick-timer = &timer2; + }; + + cpus { + cpu@0 { + cpu0-supply = <&vdd1_reg>; + }; + }; + + backlight0: backlight { + compatible = "pwm-backlight"; + pwms = <&ecap0 0 50000 0>; + brightness-levels = <0 2 5 7 10 12 15 17 20 22 25 28 30 33 35 + 38 40 43 45 48 51 53 56 58 61 63 66 68 71 + 73 76 79 81 84 86 89 91 94 96 99 102 104 + 107 109 112 114 117 119 122 124 127 130 + 132 135 137 140 142 145 147 150 153 155 + 158 160 163 165 168 170 173 175 178 181 + 183 186 188 191 193 196 198 201 204 206 + 209 211 214 216 219 221 224 226 229 232 + 234 237 239 242 244 247 249 252 255>; + default-brightness-level = <80>; + power-supply = <&backlight_reg>; + enable-gpios = <&gpio3 16 0>; + }; + + backlight_reg: fixedregulator0 { + compatible = "regulator-fixed"; + regulator-name = "backlight_reg"; + regulator-boot-on; + }; + + gpio_keys: restart-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + + restart0 { + label = "restart"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; + gpio-key,wakeup; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_blue { + label = "blue"; + gpios = <&gpio3 20 0>; + }; + led_green { + label = "green"; + gpios = <&gpio1 31 0>; + }; + led_red { + label = "red"; + gpios = <&gpio3 21 0>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + reg_lcd_3v3: fixedregulator1 { + compatible = "regulator-gpio"; + regulator-name = "lcd-3v3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-type = "voltage"; + startup-delay-us = <100>; + states = <1800000 0x1 + 2900000 0x0>; + enable-at-boot; + gpios = <&gpio3 19 0>; + enable-active-high; + }; + + vbat: fixedregulator2 { + compatible = "regulator-fixed"; + regulator-name = "vbat"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + + vmmc: fixedregulator3 { + compatible = "regulator-fixed"; + regulator-name = "vmmc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&cppi41dma { + status = "okay"; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii-txid"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +&elm { + status = "okay"; +}; + +&epwmss0 { + status = "okay"; + + ecap0: ecap@48300100 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&ecap0_pins>; + }; +}; + +&gpmc { + pinctrl-names = "default"; + pinctrl-0 = <&nandflash_pins>; + status = "okay"; + + ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ + + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + nand-bus-width = <8>; + ti,nand-ecc-opt = "bch8"; + gpmc,device-nand = "true"; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <40>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + + #address-cells = <1>; + #size-cells = <1>; + elm_id = <&elm>; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + clock-frequency = <400000>; + status = "okay"; + + tps: tps@2d { + reg = <0x2d>; + }; + eeprom: eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + pagesize = <32>; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; + status = "okay"; + + tsl2563: tsl2563@49 { + compatible = "amstaos,tsl2563"; + reg = <0x49>; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + clock-frequency = <100000>; + status = "okay"; + + egalax_ts@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio1>; + interrupts = <24 2>; + wakeup-gpios = <&gpio1 25 0>; + }; +}; + +&lcdc { + status = "okay"; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + status = "okay"; +}; + +&mmc1 { + vmmc-supply = <&vmmc>; + bus-width = <4>; + cd-gpios = <&gpio0 6 0>; + wp-gpios = <&gpio3 18 0>; + status = "okay"; +}; + +&phy_sel { + rgmii-no-delay; +}; + +#include "tps65910.dtsi" + +&tps { + vcc1-supply = <&vbat>; + vcc2-supply = <&vbat>; + vcc3-supply = <&vbat>; + vcc4-supply = <&vbat>; + vcc5-supply = <&vbat>; + vcc6-supply = <&vbat>; + vcc7-supply = <&vbat>; + vccio-supply = <&vbat>; + + regulators { + vrtc_reg: regulator@0 { + regulator-always-on; + }; + + vio_reg: regulator@1 { + regulator-always-on; + }; + + vdd1_reg: regulator@2 { + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <912500>; + regulator-max-microvolt = <1312500>; + regulator-boot-on; + regulator-always-on; + }; + + vdd2_reg: regulator@3 { + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <912500>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + vdd3_reg: regulator@4 { + regulator-always-on; + }; + + vdig1_reg: regulator@5 { + regulator-always-on; + }; + + vdig2_reg: regulator@6 { + regulator-always-on; + }; + + vpll_reg: regulator@7 { + regulator-always-on; + }; + + vdac_reg: regulator@8 { + regulator-always-on; + }; + + vaux1_reg: regulator@9 { + regulator-always-on; + }; + + vaux2_reg: regulator@10 { + regulator-always-on; + }; + + vaux33_reg: regulator@11 { + regulator-always-on; + }; + + vmmc_reg: regulator@12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + dr_mode = "host"; + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&clkout2_pin &gpio_pin>; + + clkout2_pin: pinmux_clkout2_pin { + pinctrl-single,pins = < + 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ + 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ + 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ + 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + ecap0_pins: ecap_pins { + pinctrl-single,pins = < + 0x198 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* mcasp0_axr0.gpio3_16 Backlight enable */ + 0x164 (MUX_MODE0) /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ + >; + }; + + + gpio_pin: gpio_pin { + pinctrl-single,pins = < + 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 touch reset */ + 0x60 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 touch irq */ + 0x64 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_a9.gpio1_25 touch power */ + 0x6c (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_a11.gpio1_27 pad14 to DFU */ + 0x21c (MUX_MODE0) /* usb0_drvvbus */ + 0x234 (MUX_MODE0) /* usb1_drvvbus */ + 0x1a0 (PIN_INPUT_PULLUP | MUX_MODE4) /* mcasp0_aclkr.mmc0_sdwp */ + 0x160 (PIN_INPUT_PULLUP | MUX_MODE5) /* spi0_cs1.mmc0_sdcd */ + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */ + 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + 0x150 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2) /* spi0_sclk.i2c2_sda */ + 0x154 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2) /* spi0_cs0.i2c2_scl */ + >; + }; + + lcd_pins_s0: lcd_pins_s0 { + pinctrl-single,pins = < + 0x20 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad8.lcd_data23 */ + 0x24 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad9.lcd_data22 */ + 0x28 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad10.lcd_data21 */ + 0x2c (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad11.lcd_data20 */ + 0x30 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad12.lcd_data19 */ + 0x34 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad13.lcd_data18 */ + 0x38 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad14.lcd_data17 */ + 0x3c (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad15.lcd_data16 */ + 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + 0xe0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + 0xe4 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + 0xe8 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + 0xec (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + 0x194 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* mcasp0_fsx.gpio3_15 LCD enable */ + >; + }; + + nandflash_pins: pinmux_nandflash_pins { + pinctrl-single,pins = < + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; +}; + +&wdt2 { + wdt-keep-enabled; +}; diff --git a/arch/arm/dts/am335x-pxm50.dts b/arch/arm/dts/am335x-pxm50.dts new file mode 100644 index 0000000..f4e66d2 --- /dev/null +++ b/arch/arm/dts/am335x-pxm50.dts @@ -0,0 +1,59 @@ +/* + * Copyright (C) 2014 DENX Software Engineering GmbH + * Heiko Schocher <hs(a)denx.de> + * + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am335x-pxm2.dtsi" + +/ { + model = "PXM2/PXM50"; + compatible = "ti,am335x-evm", "ti,am33xx"; + + panel { + compatible = "ti,tilcdc,panel"; + backlight = <&backlight0>; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pins_s0>; + enable-gpios = <&gpio3 15 0>; + status = "okay"; + + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <32>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + tft-alt-mode = <0>; + invert-pxl-clk = <0>; + }; + + display-timings { + native-mode = <&timing1>; + + timing1: 1376x768p50 { + clock-frequency = <60000000>; + hactive = <1376>; + vactive = <768>; + hfront-porch = <14>; + hback-porch = <64>; + hsync-len = <56>; + vback-porch = <28>; + vfront-porch = <1>; + vsync-len = <6>; + hsync-active = <1>; + vsync-active = <1>; + }; + }; + }; +}; diff --git a/arch/arm/dts/am335x-rut.dts b/arch/arm/dts/am335x-rut.dts new file mode 100644 index 0000000..c6cfbb8 --- /dev/null +++ b/arch/arm/dts/am335x-rut.dts @@ -0,0 +1,611 @@ +/* + * Copyright (C) 2014 DENX Software Engineering GmbH + * Heiko Schocher <hs(a)denx.de> + * + * Based on: + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "RUT"; + compatible = "ti,am335x-evm", "ti,am33xx"; + + buzzer { + compatible = "pwm-beeper"; + pwms = <&ecap0 0 16000 0>; + }; + + chosen { + stdout-path = &uart0; + tick-timer = &timer2; + }; + + cpus { + cpu@0 { + cpu0-supply = <&dcdc2_reg>; + }; + }; + + gpio_keys: powerfail-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + + pwr-fail0 { + label = "power-fail"; + linux,code = <KEY_POWER>; + gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>; + gpio-key,wakeup; + }; + + pwr-fail1 { + label = "power-fail-redundant"; + linux,code = <KEY_POWER>; + gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>; + gpio-key,wakeup; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_green { + label = "rut:green:debug:run_mode"; + gpios = <&gpio3 20 1>; + /* activelow = 1, default trigger heartbeat */ + }; + led_yellow { + label = "rut:debug:yellow:osc_ch1"; + gpios = <&gpio0 17 1>; + /* activelow = 1, default trigger mmc0 */ + }; + led_red { + label = "rut:debug:red:osc_ch2"; + gpios = <&gpio0 16 1>; + /* activelow = 1, default trigger debug_osc_ch2 */ + }; + /* optional */ + led_alive { + label = "rut:alive"; + gpios = <&gpio0 15 1>; + linux,default-trigger = "heartbeat"; + /* activelow = 1, default trigger heartbeat */ + }; + + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + panel { + compatible = "ti,tilcdc,panel"; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pins_s0>; + status = "okay"; + + /* FORMIKE_KWH043ST20_F01 */ + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <16>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + tft-alt-mode = <0>; + invert-pxl-clk = <1>; + }; + + display-timings { + native-mode = <&timing1>; + timing1: 480x800p60 { + clock-frequency = <29925000>; + hactive = <480>; + vactive = <800>; + hfront-porch = <50>; + hback-porch = <50>; + hsync-len = <50>; + vback-porch = <50>; + vfront-porch = <50>; + vsync-len = <50>; + hsync-active = <1>; + vsync-active = <1>; + }; + }; + }; + + vmmc: fixedregulator3 { + compatible = "regulator-fixed"; + regulator-name = "vmmc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&gpio0 14 0>; + hw_algo = "level"; + hw_margin_ms = <30000>; + }; +}; + +&aes { + status = "okay"; +}; + +&cppi41dma { + status = "okay"; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rmii"; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rmii"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; + gpios = <&gpio2 18 0>; + + ethernet_phy: ethernet-phy@1 { + compatible = "ethernet-phy-id2000.5ce1"; + reg = <1>; + natsemi,master_mode_fixup; + }; +}; + +&elm { + status = "okay"; +}; + +&epwmss0 { + status = "okay"; + + ecap0: ecap@48300100 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&ecap0_pins>; + }; +}; + +&epwmss1 { + status = "okay"; + + ehrpwm1: ehrpwm@48302200 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&epwmss1_pins>; + }; +}; + +&gpmc { + pinctrl-names = "default"; + pinctrl-0 = <&nandflash_pins>; + status = "okay"; + + ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ + + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + nand-bus-width = <8>; + ti,nand-ecc-opt = "bch8"; + gpmc,device-nand = "true"; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <57>; + gpmc,cs-wr-off-ns = <57>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <57>; + gpmc,adv-wr-off-ns = <57>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <48>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <57>; + gpmc,access-ns = <38>; + gpmc,rd-cycle-ns = <67>; + gpmc,wr-cycle-ns = <67>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <96>; + gpmc,wr-data-mux-bus-ns = <0>; + + #address-cells = <1>; + #size-cells = <1>; + elm_id = <&elm>; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + clock-frequency = <400000>; + status = "okay"; + + eeprom: eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + pagesize = <32>; + }; + + tps: tps@24 { + reg = <0x24>; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; + status = "okay"; + + atmel: atmel_mxt_ts@4a { + compatible = "atmel,maxtouch"; + reg = <0x4a>; + interrupt-parent = <&gpio1>; + interrupts = <28 8>; + gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>; + }; + + temp@48 { + compatible = "st,ds75"; + reg = <0x4c>; + }; +}; + +&lcdc { + status = "okay"; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + status = "okay"; +}; + +&mmc1 { + vmmc-supply = <&vmmc>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + status = "okay"; +}; + +&phy_sel { + rmii-clock-ext; +}; + +&sham { + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins>; + status = "okay"; + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "mx25l25635e"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <24000000>; + + partition@0 { + label = "dummy"; + reg = <0x0000000 0x8000>; + }; + }; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins>; + status = "okay"; + + lcd_init: lcd@0 { + compatible = "formike,kwh043st20"; + reg = <0>; + reset-gpios = <&gpio3 19 0>; + spi-max-frequency = <1200000>; + spi-cpol; + spi-cpha; + power-on-delay = <10>; + reset-delay = <10>; + }; +}; + +/include/ "tps65217.dtsi" + +&tps { + backlight0: backlight { + isel = <1>; /* 1 - ISET1, 2 ISET2 */ + fdim = <1000>; /* TPS65217_BL_FDIM_100HZ */ + default-brightness = <80>; + }; + + regulators { + dcdc1_reg: regulator@0 { + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1325000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + regulator-always-on; + }; + }; +}; + +&tscadc { + status = "okay"; + adc { + ti,adc-channels = <4 5 6 7>; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb0 { + dr_mode = "device"; + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&clkout2_pin &gpio_pin>; + + clkout2_pin: pinmux_clkout2_pin { + pinctrl-single,pins = < + 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs_dv */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.mii1_rxerr */ + 0x114 (MUX_MODE1) /* mii1_txen.mii1_txen */ + 0x124 (MUX_MODE1) /* mii1_txd1.mii1_txd1 */ + 0x128 (MUX_MODE1) /* mii1_txd0.mii1_txd0 */ + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.mii1_rxd1 */ + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.mii1_rxd0 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_ref_clk.rmii1_refclk */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + ecap0_pins: ecap_pins { + pinctrl-single,pins = < + 0x164 (MUX_MODE0) /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 buzzer frequency: ecap.0 */ + >; + }; + + epwmss1_pins: epwmss_pins { + pinctrl-single,pins = < + 0x48 (PIN_INPUT | MUX_MODE7) /* gpmc_a2.gpio1_18 buzzer frequency: ehrpwm1A high-Z due to connected to ecap0 by R0469 */ + 0x4c (MUX_MODE6) /* gpmc_a3.ehrpwm1B buzzer volume pwm */ + >; + }; + + gpio_pin: gpio_pin { + pinctrl-single,pins = < + 0x6c (PIN_INPUT | MUX_MODE7) /* gpmc_a11.gpio1_27 PWR_FAIL_GPIO_SPARE */ + 0x78 (PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) /* gpmc_be1n.gpio1_28 TOUCH_CHANGE_N */ + 0x88 (PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) /* gpmc_csn3.gpio2_0 RUT_GPIO0_GPIO */ + 0x118 (PIN_INPUT | MUX_MODE7) /* gmii1_rxdv.gpio3_4 PWR_FAIL_GPIO */ + 0x11c (MUX_MODE7) /* mii1_txd3.gpio0_16 DEBUG_OSC_CH2_GPIO */ + 0x120 (MUX_MODE7) /* mii1_txd2.gpio0_17 DEBUG_OSC_CH1_GPIO */ + 0x134 (MUX_MODE7) /* gmii1_rxd3.gpio2_18 PHY_RSTn_GPIO */ + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gmii1_rxd2.gpio2_19 PHY_INT_GPIO */ + 0x180 (MUX_MODE7) /* uart1_rxd.gpio0_14 WATCHDOG_TRIGGER_GPIO */ + 0x184 (MUX_MODE7) /* uart1_txd.gpio0_15 ALIVE_LED_N_GPIO */ + 0x1a0 (MUX_MODE7) /* mcasp0_aclkr.gpio3_18 MAXTOUCH_RESET_GPIO */ + 0x1a4 (MUX_MODE7) /* mcasp0_fsr.gpio3_19 DISPLAY_RESET_GPIO */ + 0x1a8 (MUX_MODE7) /* mcasp0_axr1.gpio3_20 DEBUG_RUN_MODE_GPIO */ + 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE7) /* mcasp0_ahclkx.gpio3_21 NORFLASH_WP_GPIO */ + 0x1b0 (PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x168 (PIN_INPUT | MUX_MODE3) /* uart0_ctsn.i2c1_sda */ + 0x16c (PIN_INPUT | MUX_MODE3) /* uart0.rtsn.i2c1_scl */ + >; + }; + + lcd_pins_s0: lcd_pins_s0 { + pinctrl-single,pins = < + 0x20 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad8.lcd_data23 */ + 0x24 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad9.lcd_data22 */ + 0x28 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad10.lcd_data21 */ + 0x2c (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad11.lcd_data20 */ + 0x30 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad12.lcd_data19 */ + 0x34 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad13.lcd_data18 */ + 0x38 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad14.lcd_data17 */ + 0x3c (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_ad15.lcd_data16 */ + 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + 0xe0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + 0xe4 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + 0xe8 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + 0xec (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + >; + }; + + mmc1_pins: mmc1_pins { + pinctrl-single,pins = < + 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + >; + }; + + nandflash_pins: pinmux_nandflash_pins { + pinctrl-single,pins = < + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + >; + }; + + spi0_pins: pinmux_spi0_pins { + pinctrl-single,pins = < + 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_sclk.spi0_sclk */ + 0x154 (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d0.spi0_d0 */ + 0x158 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_d1.spi0_d1 */ + 0x15c (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_CS0.spi0_CS0 */ + >; + }; + + spi1_pins: pinmux_spi1_pins { + pinctrl-single,pins = < + 0x190 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcasp0_aclkx.spi1_sclk */ + 0x194 (PIN_INPUT_PULLUP | MUX_MODE3) /* mcasp0_fsx.spi1_d0 */ + 0x198 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcasp0_axr0.spi1_d1 */ + 0x19c (PIN_INPUT_PULLUP | MUX_MODE3) /* mcasp0_ahclkr.spi1_cs0 */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; +}; diff --git a/configs/draco_defconfig b/configs/draco_defconfig index 0a437ed..f71a1cd 100644 --- a/configs/draco_defconfig +++ b/configs/draco_defconfig @@ -1,5 +1,8 @@ CONFIG_ARM=y CONFIG_TARGET_DRACO=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_DM_SERIAL=y +CONFIG_DEFAULT_DEVICE_TREE="am335x-draco" CONFIG_SPL=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="U-Boot# " @@ -22,6 +25,9 @@ CONFIG_CMD_PING=y CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y CONFIG_CMD_EXT2=y +CONFIG_OF_CONTROL=y +CONFIG_OF_EMBED=y +CONFIG_DM=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_WINBOND=y CONFIG_SYS_NS16550=y diff --git a/configs/etamin_defconfig b/configs/etamin_defconfig index 3f21bc4..ad7ddbd 100644 --- a/configs/etamin_defconfig +++ b/configs/etamin_defconfig @@ -1,17 +1,42 @@ CONFIG_ARM=y CONFIG_TARGET_ETAMIN=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_DM_SERIAL=y +CONFIG_DEFAULT_DEVICE_TREE="am335x-draco" CONFIG_SPL=y +CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="U-Boot# " CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n" CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b" # CONFIG_CMD_IMLS is not set +CONFIG_CMD_ASKENV=y # CONFIG_CMD_FLASH is not set +CONFIG_CMD_MMC=y +CONFIG_CMD_SF=y +CONFIG_CMD_I2C=y +CONFIG_CMD_USB=y +CONFIG_CMD_DFU=y CONFIG_CMD_GPIO=y # CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIME=y +CONFIG_CMD_EXT2=y +CONFIG_OF_CONTROL=y +CONFIG_OF_EMBED=y +CONFIG_DM=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_WINBOND=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_MUSB_HOST=y +CONFIG_USB_MUSB_GADGET=y CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_G_DNL_MANUFACTURER="Siemens AG" +CONFIG_G_DNL_VENDOR_NUM=0x0908 +CONFIG_G_DNL_PRODUCT_NUM=0x02d2 CONFIG_OF_LIBFDT=y diff --git a/configs/pxm2_defconfig b/configs/pxm2_defconfig index 8655665..b6ad69b 100644 --- a/configs/pxm2_defconfig +++ b/configs/pxm2_defconfig @@ -1,5 +1,8 @@ CONFIG_ARM=y CONFIG_TARGET_PXM2=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_DM_SERIAL=y +CONFIG_DEFAULT_DEVICE_TREE="am335x-pxm50" CONFIG_SPL=y CONFIG_FIT=y CONFIG_HUSH_PARSER=y @@ -24,6 +27,9 @@ CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y +CONFIG_OF_CONTROL=y +CONFIG_OF_EMBED=y +CONFIG_DM=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_WINBOND=y CONFIG_SYS_NS16550=y diff --git a/configs/rastaban_defconfig b/configs/rastaban_defconfig index ec89f05..2643cb7 100644 --- a/configs/rastaban_defconfig +++ b/configs/rastaban_defconfig @@ -1,5 +1,8 @@ CONFIG_ARM=y CONFIG_TARGET_RASTABAN=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_DM_SERIAL=y +CONFIG_DEFAULT_DEVICE_TREE="am335x-draco" CONFIG_SPL=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="U-Boot# " @@ -22,6 +25,9 @@ CONFIG_CMD_PING=y CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y CONFIG_CMD_EXT2=y +CONFIG_OF_CONTROL=y +CONFIG_OF_EMBED=y +CONFIG_DM=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_WINBOND=y CONFIG_SYS_NS16550=y diff --git a/configs/rut_defconfig b/configs/rut_defconfig index 406eaf3..351808d 100644 --- a/configs/rut_defconfig +++ b/configs/rut_defconfig @@ -1,5 +1,8 @@ CONFIG_ARM=y CONFIG_TARGET_RUT=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_DM_SERIAL=y +CONFIG_DEFAULT_DEVICE_TREE="am335x-rut" CONFIG_SPL=y CONFIG_FIT=y CONFIG_HUSH_PARSER=y @@ -24,6 +27,9 @@ CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y +CONFIG_OF_CONTROL=y +CONFIG_OF_EMBED=y +CONFIG_DM=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_WINBOND=y CONFIG_SYS_NS16550=y diff --git a/configs/thuban_defconfig b/configs/thuban_defconfig index f9391f2..7cd6992 100644 --- a/configs/thuban_defconfig +++ b/configs/thuban_defconfig @@ -1,5 +1,8 @@ CONFIG_ARM=y CONFIG_TARGET_THUBAN=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_DM_SERIAL=y +CONFIG_DEFAULT_DEVICE_TREE="am335x-draco" CONFIG_SPL=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="U-Boot# " @@ -22,6 +25,9 @@ CONFIG_CMD_PING=y CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y CONFIG_CMD_EXT2=y +CONFIG_OF_CONTROL=y +CONFIG_OF_EMBED=y +CONFIG_DM=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_WINBOND=y CONFIG_SYS_NS16550=y diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h index 5969541..eab665c 100644 --- a/include/configs/siemens-am33x-common.h +++ b/include/configs/siemens-am33x-common.h @@ -102,8 +102,10 @@ #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ /* NS16550 Configuration */ +#ifdef CONFIG_SPL_BUILD #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE (-4) +#endif #define CONFIG_SYS_NS16550_CLK (48000000) #define CONFIG_SYS_NS16550_COM1 0x44e09000 #define CONFIG_SYS_NS16550_COM4 0x481a6000 -- 2.5.5

1 0

[U-Boot] [PATCH 1/2 v2] powerpc:t4240rdb: Disable the non-existent ethernet port on T4240RDB
by ying.zhang＠freescale.com 25 May '16

25 May '16

From: Ying Zhang <b40530(a)freescale.com> There are 12 ethernet port on T4240RDB, but there need to set 16 MAC addressed for ethernets. There need to disable non-existent ethernet ports in U-boot Signed-off-by: Ying Zhang <b40530(a)freescale.com> --- [changed from v1]: --- update the title. board/freescale/t4rdb/eth.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/board/freescale/t4rdb/eth.c b/board/freescale/t4rdb/eth.c index e563a61..ae2451e 100644 --- a/board/freescale/t4rdb/eth.c +++ b/board/freescale/t4rdb/eth.c @@ -77,6 +77,9 @@ int board_eth_init(bd_t *bis) puts("Invalid SerDes1 protocol for T4240RDB\n"); } + fm_disable_port(FM1_DTSEC5); + fm_disable_port(FM1_DTSEC6); + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { interface = fm_info_get_enet_if(i); switch (interface) { @@ -115,6 +118,8 @@ int board_eth_init(bd_t *bis) puts("Invalid SerDes2 protocol for T4240RDB\n"); } + fm_disable_port(FM2_DTSEC5); + fm_disable_port(FM2_DTSEC6); for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) { interface = fm_info_get_enet_if(i); switch (interface) { -- 2.1.0.27.g96db324

2 2

[U-Boot] [PATCH 1/2 v3] powerpc:t4240rdb: Disable the non-existent ethernet ports on T4240RDB
by ying.zhang22455＠nxp.com 25 May '16

25 May '16

From: Ying Zhang <ying.zhang22455(a)nxp.com> Disable the non-existent ethernet ports on T4240RDB:FM1_DTSEC5, FM1_DTSEC6, FM2_DTSEC5 and FM2_DTSEC6. Signed-off-by: Ying Zhang <ying.zhang22455(a)nxp.com> --- [changed from v1]: --- update the title. [changed from v2]: --- update the commit message. board/freescale/t4rdb/eth.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/board/freescale/t4rdb/eth.c b/board/freescale/t4rdb/eth.c index e563a61..ae2451e 100644 --- a/board/freescale/t4rdb/eth.c +++ b/board/freescale/t4rdb/eth.c @@ -77,6 +77,9 @@ int board_eth_init(bd_t *bis) puts("Invalid SerDes1 protocol for T4240RDB\n"); } + fm_disable_port(FM1_DTSEC5); + fm_disable_port(FM1_DTSEC6); + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { interface = fm_info_get_enet_if(i); switch (interface) { @@ -115,6 +118,8 @@ int board_eth_init(bd_t *bis) puts("Invalid SerDes2 protocol for T4240RDB\n"); } + fm_disable_port(FM2_DTSEC5); + fm_disable_port(FM2_DTSEC6); for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) { interface = fm_info_get_enet_if(i); switch (interface) { -- 2.1.0.27.g96db324

3 2

[U-Boot] [PATCH] powerpc/mpc85xx: set L2PE in L2CSR0 before enabling L2 cache
by Aneesh Bansal 25 May '16

25 May '16

While enabling L2 cache, the value of L2PE (L2 cache parity/ECC error checking enable) must not be changed while the L2 cache is enabled. So, L2PE must be set before enabling L2 cache. Signed-off-by: Aneesh Bansal <aneesh.bansal(a)nxp.com> --- arch/powerpc/cpu/mpc85xx/start.S | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/powerpc/cpu/mpc85xx/start.S b/arch/powerpc/cpu/mpc85xx/start.S index 82a151a..4c51225 100644 --- a/arch/powerpc/cpu/mpc85xx/start.S +++ b/arch/powerpc/cpu/mpc85xx/start.S @@ -720,16 +720,39 @@ enable_l2_cluster_l2: ori r4, r4, (L2CSR0_L2FI|L2CSR0_L2LFC)@l sync stw r4, 0(r3) /* invalidate L2 */ + /* Poll till the bits are cleared */ 1: sync lwz r0, 0(r3) twi 0, r0, 0 isync and. r1, r0, r4 bne 1b + + /* L2PE must be set before L2 cache is enabled */ + lis r4, (L2CSR0_L2PE)@h + ori r4, r4, (L2CSR0_L2PE)@l + sync + stw r4, 0(r3) /* enable L2 parity/ECC error checking */ + /* Poll till the bit is set */ +1: sync + lwz r0, 0(r3) + twi 0, r0, 0 + isync + and. r1, r0, r4 + beq 1b + lis r4, (L2CSR0_L2E|L2CSR0_L2PE)@h ori r4, r4, (L2CSR0_L2REP_MODE)@l sync stw r4, 0(r3) /* enable L2 */ + /* Poll till the bit is set */ +1: sync + lwz r0, 0(r3) + twi 0, r0, 0 + isync + and. r1, r0, r4 + beq 1b + delete_ccsr_l2_tlb: delete_tlb0_entry 0, CONFIG_SYS_CCSRBAR + 0xC20000, MAS2_I|MAS2_G, r3 #endif -- 1.8.1.4

2 6

[U-Boot] [PATCH] powerpc/t2080qds: Enable qixis commands to reboot from NAND and SD
by York Sun 25 May '16

25 May '16

Signed-off-by: York Sun <york.sun(a)nxp.com> CC: Shengzhou Liu <Shengzhou.Liu(a)nxp.com> --- include/configs/T208xQDS.h | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/include/configs/T208xQDS.h b/include/configs/T208xQDS.h index 5957fa8..ec53ff0 100644 --- a/include/configs/T208xQDS.h +++ b/include/configs/T208xQDS.h @@ -291,6 +291,10 @@ unsigned long get_board_ddr_clk(void); #define QIXIS_LBMAP_SHIFT 0 #define QIXIS_LBMAP_DFLTBANK 0x00 #define QIXIS_LBMAP_ALTBANK 0x04 +#define QIXIS_LBMAP_NAND 0x09 +#define QIXIS_LBMAP_SD 0x00 +#define QIXIS_RCW_SRC_NAND 0x104 +#define QIXIS_RCW_SRC_SD 0x040 #define QIXIS_RST_CTL_RESET 0x83 #define QIXIS_RST_FORCE_MEM 0x1 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 -- 1.7.9.5

1 1

[U-Boot] [PATCH 1/2] powerpc/t208xqds: Update MAINTAINERS file
by York Sun 25 May '16

25 May '16

Signed-off-by: York Sun <york.sun(a)nxp.com> CC: Shengzhou Liu <Shengzhou.Liu(a)nxp.com> --- board/freescale/t208xqds/MAINTAINERS | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/board/freescale/t208xqds/MAINTAINERS b/board/freescale/t208xqds/MAINTAINERS index deda092..d747de3 100644 --- a/board/freescale/t208xqds/MAINTAINERS +++ b/board/freescale/t208xqds/MAINTAINERS @@ -1,5 +1,5 @@ T208XQDS BOARD -#M: - +M: Shengzhou Liu <Shengzhou.Liu(a)nxp.com> S: Maintained F: board/freescale/t208xqds/ F: include/configs/T208xQDS.h -- 1.7.9.5

1 3

[U-Boot] [RFC PATCH] powerpc: Disable flush or invalidate dcache by range for some SoCs
by York Sun 25 May '16

25 May '16

Commit ac337168a unified functions to flush and invalidate dcache by range. These two functions were no-op for SoCs other than 4xx and MPC86xx. Adding these functions seemed to be correct but introduced issues when the dcache is flushed. While the root cause is under investigation, disable these functions for affected SoCs so various drivers can work. Signed-off-by: York Sun <york.sun(a)nxp.com> --- arch/powerpc/lib/ppccache.S | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/powerpc/lib/ppccache.S b/arch/powerpc/lib/ppccache.S index b96dbc6..66cf02d 100644 --- a/arch/powerpc/lib/ppccache.S +++ b/arch/powerpc/lib/ppccache.S @@ -65,6 +65,7 @@ ppcSync: * flush_dcache_range(unsigned long start, unsigned long stop) */ _GLOBAL(flush_dcache_range) +#if defined(CONFIG_4xx) || defined(CONFIG_MPC86xx) li r5,L1_CACHE_BYTES-1 andc r3,r3,r5 subf r4,r3,r4 @@ -77,6 +78,7 @@ _GLOBAL(flush_dcache_range) addi r3,r3,L1_CACHE_BYTES bdnz 1b sync /* wait for dcbst's to get to ram */ +#endif blr /* @@ -87,6 +89,7 @@ _GLOBAL(flush_dcache_range) * invalidate_dcache_range(unsigned long start, unsigned long stop) */ _GLOBAL(invalidate_dcache_range) +#if defined(CONFIG_4xx) || defined(CONFIG_MPC86xx) li r5,L1_CACHE_BYTES-1 andc r3,r3,r5 subf r4,r3,r4 @@ -100,5 +103,6 @@ _GLOBAL(invalidate_dcache_range) addi r3,r3,L1_CACHE_BYTES bdnz 1b sync /* wait for dcbi's to get to ram */ +#endif blr -- 1.7.9.5

1 1

[U-Boot] Please pull u-boot-dm
by Simon Glass 25 May '16

25 May '16

Hi Tom, This includes a refinement of the GPIO interface, soft SPI fixes, driver model block-device support (and a legacy driver for non-driver-model code) and a few other things. The changes are fairly major so I'd like to get the maximum possible test window. The following changes since commit aeaec0e682f45b9e0c62c522fafea353931f73ed: Prepare v2016.05 (2016-05-16 10:40:32 -0400) are available in the git repository at: git://git.denx.de/u-boot-dm.git for you to fetch changes up to 341392dd115f1385c31bb0b034ec15f542730e30: dm: mmc: test: Add tests for MMC (2016-05-17 09:54:43 -0600) ---------------------------------------------------------------- Eric Nelson (6): dm: gpio: add a default gpio xlate routine gpio: intel_broadwell: remove gpio_xlate routine gpio: omap: remove gpio_xlate routine gpio: pic32: remove gpio_xlate routine gpio: rk: remove gpio_xlate routine gpio: exynos(s5p): remove gpio_xlate routine Mugunthan V N (1): drivers: usb: common: add common code for usb drivers to use Peng Fan (5): dm: gpio: pca953x: introduce driver model support for pca953x dm: spi: soft_spi bug fix dm: spi: soft_spi: switch to use linux compatible string dm: spi: introduce dm api dm: gpio: introduce 74x164 driver Simon Glass (67): Revert "dm: sandbox: Drop the pre-DM host implementation" dm: sandbox: Add a board for sandbox without CONFIG_BLK pci: Drop CONFIG_SYS_SCSI_SCAN_BUS_REVERSE dm: Rename disk uclass to ahci Allow iotrace byte access to use an address of any size sandbox: Add string and 16-bit I/O functions sandbox: Add dummy SCSI functions sandbox: Add dummy SATA functions dm: scsi: Remove the forward declarations dm: scsi: Fix up code style dm: ide: Correct various code style problems dm: ide: Remove the forward declarations dm: sata: Fix code style problems in cmd/sata.c dm: scsi: Rename CONFIG_CMD_SCSI to CONFIG_SCSI dm: blk: Add a legacy block interface dm: systemace: Add a legacy block interface dm: sandbox: Add a legacy host block interface dm: usb: Add a legacy block interface for USB storage dm: mmc: Add a legacy block interface for MMC dm: mmc: Add an implementation of the 'devnum' functions dm: scsi: Separate the non-command code into its own file dm: ide: Separate the non-command code into its own file dm: sata: Separate the non-command code into its own file dm: disk: Use legacy block driver info for block device access dm: usb: Drop the get_dev() function dm: ide: Drop the get_dev() function dm: mmc: Drop the get_dev() function dm: scsi: Drop the get_dev() function dm: sata: Drop the get_dev() function dm: systemace: Drop the get_dev() function dm: blk: Drop the systemace.h header dm: sandbox: Drop the host_get_dev() function dm: part: Drop the get_dev() method dm: ide: Add support for driver-model block devices dm: sandbox: Enable IDE dm: scsi: Add support for driver-model block devices dm: sandbox: Enable SCSI dm: sata: Add support for driver-model block devices dm: sandbox: Enable SATA dm: blk: Allow blk_create_device() to allocate the device number dm: blk: Add a easier way to create a named block device dm: systemace: Reorder function to avoid forward declarataions dm: systemace: Add driver-mode block-device support dm: sandbox: Enable systemace dm: blk: Fix allocation of block-device numbering dm: core: Allow device names to be freed automatically dm: blk: Free the block device name when unbound dm: mmc: Move mmc_switch_part() above its callers dm: mmc: Implement the select_hwpart() method dm: mmc: Add a function to obtain the block device dm: mmc: spl: Use the legacy block interface in SPL dm: mmc: Use the new select_hwpart() API dm: blk: Add functions to select a hardware partition dm: part: Use the legacy block driver for hardware partition support dm: part: Drop the block_drvr table dm: blk: Add a comment as to why the bdev member is needed dm: mmc: Set up the device pointer when using the MMC uclass dm: mmc: Move the device list into a separate file dm: blk: Use the correct error code for blk_get_device_by_str() dm: mmc: Adjust mmc_switch_part() to use a struct mmc dm: sandbox: Only enable the sandbox MMC driver when valid dm: mmc: Implement the MMC functions for block devices dm: mmc: Add a way to bind MMC devices with driver model dm: mmc: Add support for driver-model block devices dm: mmc: sandbox: Add an SD-card emulation dm: sandbox: mmc: Enable building MMC code for sandbox dm: mmc: test: Add tests for MMC Stephen Warren (4): buildman: allow more incremental building dm: core: allow drivers to refuse to bind video: tegra: refuse to bind to disabled dcs fdt: fix dev_get_addr_name node offset angelo(a)sysam.it (2): m68k: add malloc memory for early malloc m68k: add DM model serial driver README | 4 +- api/api_storage.c | 2 +- arch/arm/dts/exynos4210-universal_c210.dts | 10 +- arch/arm/dts/tegra20-seaboard.dts | 4 - arch/arm/include/asm/arch-ls102xa/config.h | 2 +- arch/m68k/cpu/mcf5227x/start.S | 25 +- arch/m68k/cpu/mcf523x/start.S | 27 +- arch/m68k/cpu/mcf52x2/start.S | 26 +- arch/m68k/cpu/mcf530x/cpu_init.c | 2 +- arch/m68k/cpu/mcf530x/start.S | 25 +- arch/m68k/cpu/mcf532x/start.S | 27 +- arch/m68k/cpu/mcf5445x/start.S | 27 +- arch/m68k/cpu/mcf547x_8x/start.S | 25 +- arch/m68k/include/asm/config.h | 2 - arch/sandbox/include/asm/io.h | 15 + arch/x86/Kconfig | 3 + arch/x86/cpu/broadwell/sata.c | 2 +- arch/x86/cpu/intel_common/cpu.c | 2 +- arch/x86/cpu/ivybridge/bd82x6x.c | 2 +- arch/x86/cpu/ivybridge/sata.c | 2 +- board/cm5200/fwupdate.c | 2 +- board/mpl/pip405/README | 6 +- board/sandbox/MAINTAINERS | 7 + cmd/Makefile | 8 +- cmd/disk.c | 2 +- cmd/ide.c | 1352 +----------------------- cmd/mmc.c | 18 +- cmd/sata.c | 142 +-- cmd/scsi.c | 753 ++----------- cmd/usb.c | 16 +- common/Makefile | 6 + common/board_r.c | 4 +- common/env_mmc.c | 6 +- common/ide.c | 1231 +++++++++++++++++++++ common/sata.c | 115 ++ common/scsi.c | 592 +++++++++++ common/spl/spl_mmc.c | 2 +- common/spl/spl_sata.c | 2 +- common/spl/spl_usb.c | 2 +- common/usb_storage.c | 37 +- configs/sandbox_defconfig | 2 + configs/sandbox_noblk_defconfig | 168 +++ disk/part.c | 83 +- drivers/Makefile | 2 + drivers/block/Kconfig | 5 +- drivers/block/Makefile | 8 +- drivers/block/{disk-uclass.c => ahci-uclass.c} | 6 +- drivers/block/blk-uclass.c | 361 +++++++ drivers/block/blk_legacy.c | 261 +++++ drivers/block/sandbox.c | 103 +- drivers/block/sandbox_scsi.c | 29 + drivers/block/sata_sandbox.c | 33 + drivers/block/sym53c8xx.c | 2 +- drivers/block/systemace.c | 110 +- drivers/core/device-remove.c | 2 + drivers/core/device.c | 10 +- drivers/core/lists.c | 4 + drivers/dfu/dfu_mmc.c | 13 +- drivers/gpio/74x164_gpio.c | 193 ++++ drivers/gpio/Kconfig | 30 + drivers/gpio/Makefile | 3 + drivers/gpio/gpio-uclass.c | 30 +- drivers/gpio/intel_broadwell_gpio.c | 10 - drivers/gpio/omap_gpio.c | 11 - drivers/gpio/pca953x_gpio.c | 351 ++++++ drivers/gpio/pic32_gpio.c | 10 - drivers/gpio/rk_gpio.c | 11 - drivers/gpio/s5p_gpio.c | 11 - drivers/mmc/Kconfig | 11 +- drivers/mmc/Makefile | 12 +- drivers/mmc/mmc-uclass.c | 106 ++ drivers/mmc/mmc.c | 311 +++--- drivers/mmc/mmc_legacy.c | 108 ++ drivers/mmc/mmc_private.h | 33 +- drivers/mmc/mmc_write.c | 18 +- drivers/mmc/omap_hsmmc.c | 1 + drivers/mmc/pic32_sdhci.c | 7 +- drivers/mmc/rockchip_dw_mmc.c | 1 + drivers/mmc/sandbox_mmc.c | 134 ++- drivers/mmc/socfpga_dw_mmc.c | 1 + drivers/mmc/uniphier-sd.c | 1 + drivers/mmc/zynq_sdhci.c | 1 + drivers/pci/pci.c | 4 - drivers/serial/mcfuart.c | 188 +++- drivers/spi/soft_spi.c | 55 +- drivers/spi/spi-uclass.c | 28 +- drivers/usb/common/Makefile | 1 + drivers/usb/common/common.c | 40 + drivers/video/tegra.c | 7 + fs/fat/fat.c | 2 +- include/asm-generic/gpio.h | 19 +- include/blk.h | 263 ++++- include/config_cmd_all.h | 2 +- include/config_distro_bootcmd.h | 6 +- include/config_fallbacks.h | 2 +- include/configs/MPC8544DS.h | 2 +- include/configs/MPC8572DS.h | 2 +- include/configs/MPC8610HPCD.h | 2 +- include/configs/MPC8641HPCN.h | 4 +- include/configs/PIP405.h | 2 +- include/configs/am57xx_evm.h | 2 +- include/configs/cm_t54.h | 2 +- include/configs/db-88f6820-gp.h | 2 +- include/configs/dra7xx_evm.h | 2 +- include/configs/efi-x86.h | 2 +- include/configs/galileo.h | 2 +- include/configs/highbank.h | 2 +- include/configs/ls1043aqds.h | 2 +- include/configs/ls2080aqds.h | 2 +- include/configs/ls2080ardb.h | 2 +- include/configs/omap5_uevm.h | 2 +- include/configs/qemu-x86.h | 2 +- include/configs/sandbox.h | 25 + include/configs/sbc8641d.h | 2 - include/configs/sunxi-common.h | 2 +- include/configs/x86-common.h | 2 +- include/configs/xilinx_zynqmp.h | 2 +- include/dm/device.h | 16 + include/dm/platform_data/serial_coldfire.h | 23 + include/dm/uclass-id.h | 2 +- include/ide.h | 8 + include/iotrace.h | 5 +- include/linux/usb/otg.h | 9 + include/mmc.h | 38 +- include/part.h | 33 - include/spi.h | 52 + include/systemace.h | 17 - include/usb.h | 1 - lib/efi_loader/efi_disk.c | 27 +- test/dm/blk.c | 4 +- test/dm/mmc.c | 19 + tools/buildman/README | 42 + tools/buildman/builder.py | 10 +- tools/buildman/builderthread.py | 24 +- tools/buildman/cmdline.py | 4 + tools/buildman/control.py | 4 +- 136 files changed, 5419 insertions(+), 2749 deletions(-) create mode 100644 common/ide.c create mode 100644 common/sata.c create mode 100644 common/scsi.c create mode 100644 configs/sandbox_noblk_defconfig rename drivers/block/{disk-uclass.c => ahci-uclass.c} (72%) create mode 100644 drivers/block/blk_legacy.c create mode 100644 drivers/block/sandbox_scsi.c create mode 100644 drivers/block/sata_sandbox.c create mode 100644 drivers/gpio/74x164_gpio.c create mode 100644 drivers/gpio/pca953x_gpio.c create mode 100644 drivers/mmc/mmc_legacy.c create mode 100644 drivers/usb/common/common.c create mode 100644 include/dm/platform_data/serial_coldfire.h delete mode 100644 include/systemace.h Regards, Simon

3 8