July 2009 - U-Boot

[U-Boot] [PATCH] uec: Fix compile warning
by Kumar Gala 23 Jul '09

23 Jul '09

cpu.c: In function 'cpu_eth_init': cpu.c:371: warning: implicit declaration of function 'uec_standard_init' Signed-off-by: Kumar Gala <galak(a)kernel.crashing.org> --- include/netdev.h | 1 + 1 files changed, 1 insertions(+), 0 deletions(-) diff --git a/include/netdev.h b/include/netdev.h index aed5c4c..92eceb1 100644 --- a/include/netdev.h +++ b/include/netdev.h @@ -50,6 +50,7 @@ int e1000_initialize(bd_t *bis); int eepro100_initialize(bd_t *bis); int eth_3com_initialize (bd_t * bis); int fec_initialize (bd_t *bis); +int uec_standard_init(bd_t *bis); int greth_initialize(bd_t *bis); void gt6426x_eth_initialize(bd_t *bis); int inca_switch_initialize(bd_t *bis); -- 1.6.0.6

2 4

[U-Boot] MPC8360ERDK - DDR Controller and DDR2 Memory initialization/configuration
by cmfairfa＠rockwellcollins.com 23 Jul '09

23 Jul '09

Hi, For the MPC8360ERDK, U-Boot configures the Micron DDR2 chips (in MPC8360ERDK.h) inconsistently with the chip's data sheet specifications (e.g., for the -3 speed grade part, the CAS Latency is specified to be 5, but the software uses 3). I'm looking for any information/input as to how the DDR controller and DDR2 chip settings were derived since most of the settings don't match the chip's specifications. I notice that a lot of the U-Boot settings are 2 clock cycles less than what is specified for the chip. Is this merely a coincedence or is there an "inherent" 2 clock cycle delay in the hardware? Any help is greatly appreciated. Thanks. Christopher M. Fairfax Sr. Software Engineer Rockwell Collins +1 540-428-3344 +1 540-428-3301 cmfairfa(a)rockwellcollins.com This message contains PRIVILEGED AND PROPRIETARY INFORMATION intended solely for the use of the addressee(s) named above. Any disclosure, distribution, copying or use of the information by others is strictly prohibited. If you have received this message in error, please advise the sender by immediate reply and delete the original message. Thank you.

1 0

[U-Boot] kirkwood openRD-base / PCI support
by Dieter Kiermaier 23 Jul '09

23 Jul '09

Hi Prafulla, hi list, is there anywhere pci support available for u-boot on openrd-base board? I've googled and searched the list archive but aren't sucessful :-( It looks like there is no PCI support until now, Are there any plans to do this from marvell side? I use Simons patches for initial openrd-base support and try to get up kirkwoods PCI port. u-boot without PCI is running fine on my openrd-base board. Many thanks, Dieter

1 0

Re: [U-Boot] How to start U-Boot for i.MX31 NAND out of RedBoot (out of RAM)
by Ulrich Gerster 23 Jul '09

23 Jul '09

Hello >>>> Magnus Lilja <lilja.magnus(a)gmail.com> 14.07.09 19.43 Uhr >>> > Hi >>>>2009/7/14 Ulrich Gerster <gersteru(a)dhbw-loerrach.de>: >> Hello. >> >>>>> Magnus Lilja <lilja.magnus(a)gmail.com> 14.07.09 16.03 Uhr >>> >> >>>> I used the patch from you out of this posting: >>>> [U-Boot-Users] [PATCH RFC 3/5] i.MX31: Add i.MX31 NAND Flash Controller driver. >>>> http://lists.denx.de/pipermail/u-boot/2008-August/038239.html >>>> >>>> They should work, or not? Do they require something else? >> >>> I haven't tried that driver on a recent U-boot so I don't know if (or >>> how) it will work when applied to a recent U-Boot. >> >> I'm using the u-boot master release of middle of June. >> How can I ensure that your patch is working? Or how do I know what is missing that it works? > You need to use either a debugger or add printf's to see what's going > on (to the mxc_nd.c or whatever the file is called. I have the drivers working now. But there's a little problem left. When I try to use u-boot to update itself (write itself from RAM to Flash) it seems that it overwrites the out of band information too. So when I try to reboot nothing is working because every program assumes that the first blocks are bad. Do you have a suggestion how to fix that issue? Thanks. Ulrich Gerster

2 1

[U-Boot] kirkwood sheevaplug - broken build using git.denx.de/u-boot.git
by Dieter Kiermaier 23 Jul '09

23 Jul '09

Hi all, I've tried to build u-boot for sheevaplug from git.denx.de/u-boot.git Is this expected to work or are there some missing dependencies or what am I doing wrong? (The same happens on u-boot-arm custodian tree. Only Prafullas tree from git.marvell.com allows me to build u-boot for sheevaplug.) The build gives me following error (without any prior warnings!): make[1]: Verlasse Verzeichnis '/home/dieter/git/u-boot/u-boot.git/cpu/arm926ejs' UNDEF_SYM=`arm-none-linux-gnueabi-objdump -x board/Marvell/sheevaplug/libsheevaplug.a lib_generic/libgeneric.a lib_generic/lzma/liblzma.a lib_generic/lzo/liblzo.a cpu/arm926ejs/libarm926ejs.a cpu/arm926ejs/kirkwood/libkirkwood.a lib_arm/libarm.a fs/cramfs/libcramfs.a fs/fat/libfat.a fs/fdos/libfdos.a fs/jffs2/libjffs2.a fs/reiserfs/libreiserfs.a fs/ext2/libext2fs.a fs/yaffs2/libyaffs2.a fs/ubifs/libubifs.a net/libnet.a disk/libdisk.a drivers/bios_emulator/libatibiosemu.a drivers/block/libblock.a drivers/dma/libdma.a drivers/fpga/libfpga.a drivers/gpio/libgpio.a drivers/hwmon/libhwmon.a drivers/i2c/libi2c.a drivers/input/libinput.a drivers/misc/libmisc.a drivers/mmc/libmmc.a drivers/mtd/libmtd.a drivers/mtd/nand/libnand.a drivers/mtd/onenand/libonenand.a drivers/mtd/ubi/libubi.a drivers/mtd/spi/libspi_flash.a drivers/net/libnet.a drivers/net/phy/libphy.a drivers/net/sk98lin/libsk98lin.a drivers/pci/libpci.a drivers/pcmcia/libpcmcia.a drivers/spi/libspi.a drivers/rtc/librtc.a drivers/serial/libserial.a drivers/twserial/libtws.a drivers/usb/gadget/libusb_gadget.a drivers/usb/host/libusb_host.a drivers/usb/musb/libusb_musb.a drivers/video/libvideo.a drivers/watchdog/libwatchdog.a common/libcommon.a libfdt/libfdt.a api/libapi.a post/libpost.a | sed -n -e 's/.*$__u_boot_cmd_.*$/-u\1/p'|sort|uniq`; cd /home/dieter/git/u-boot/u-boot.git && arm-none-linux-gnueabi-ld -Bstatic -T /home/dieter/git/u-boot/u-boot.git/cpu/arm926ejs/u-boot.lds -Ttext 0x00600000 $UNDEF_SYM cpu/arm926ejs/start.o --start-group lib_generic/libgeneric.a lib_generic/lzma/liblzma.a lib_generic/lzo/liblzo.a cpu/arm926ejs/libarm926ejs.a cpu/arm926ejs/kirkwood/libkirkwood.a lib_arm/libarm.a fs/cramfs/libcramfs.a fs/fat/libfat.a fs/fdos/libfdos.a fs/jffs2/libjffs2.a fs/reiserfs/libreiserfs.a fs/ext2/libext2fs.a fs/yaffs2/libyaffs2.a fs/ubifs/libubifs.a net/libnet.a disk/libdisk.a drivers/bios_emulator/libatibiosemu.a drivers/block/libblock.a drivers/dma/libdma.a drivers/fpga/libfpga.a drivers/gpio/libgpio.a drivers/hwmon/libhwmon.a drivers/i2c/libi2c.a drivers/input/libinput.a drivers/misc/libmisc.a drivers/mmc/libmmc.a drivers/mtd/libmtd.a drivers/mtd/nand/libnand.a drivers/mtd/onenand/libonenand.a drivers/mtd/ubi/libubi.a drivers/mtd/spi/libspi_flash.a drivers/net/libnet.a drivers/net/phy/libphy.a drivers/net/sk98lin/libsk98lin.a drivers/pci/libpci.a drivers/pcmcia/libpcmcia.a drivers/spi/libspi.a drivers/rtc/librtc.a drivers/serial/libserial.a drivers/twserial/libtws.a drivers/usb/gadget/libusb_gadget.a drivers/usb/host/libusb_host.a drivers/usb/musb/libusb_musb.a drivers/video/libvideo.a drivers/watchdog/libwatchdog.a common/libcommon.a libfdt/libfdt.a api/libapi.a post/libpost.a board/Marvell/sheevaplug/libsheevaplug.a --end-group -L /opt/Orion-SDK/armel-2.0/tools/gcc/bin/../lib/gcc/arm-none-linux-gnueabi/4.2.0 -lgcc -Map u-boot.map -o u-boot arm-none-linux-gnueabi-ld: ERROR: Source object /opt/Orion-SDK/armel-2.0/tools/gcc/bin/../lib/gcc/arm-none-linux-gnueabi/4.2.0/libgcc.a(_lshrdi3.o) has EABI version 4, but target u-boot has EABI version 0 arm-none-linux-gnueabi-ld: failed to merge target specific data of file /opt/Orion-SDK/armel-2.0/tools/gcc/bin/../lib/gcc/arm-none-linux-gnueabi/4.2.0/libgcc.a(_lshrdi3.o) make: *** [u-boot] Fehler 1 Used gcc is: arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease) Any hints are very welcome. Many thanks, Dieter

2 2

[U-Boot] FW: ARM Pull Request
by Prafulla Wadaskar 23 Jul '09

23 Jul '09

> > > Prafulla Wadaskar (3): > > > Marvell Sheevaplug Board support > > > Marvell MV88F6281GTW_GE Board support > > > Marvell RD6281A Board support Hi Ben, I think Pull request net not yet applied. This breaks build for RD6281A board. Some discussion was going for "net: Kirkwood_egiga: forced interface speed config support" patch inclusion. Jean has voted to keep this patch. Ref http://lists.denx.de/pipermail/u-boot/2009-July/057139.html even if wolfgang decides to skip this patch, rest other should be applied. Thanks and Regards.. Prafulla . .

4 7

[U-Boot] Nothing Else…MONEY! MONEY! MONEY!!!!!
by hazelwani 282 23 Jul '09

23 Jul '09

*Nothing Else…MONEY! MONEY! MONEY!!!!!* Hi guys, This really works! Just click to the ads and get a MONEY! You can wake up tomorrow morning log-in your account and find $15,000 PAYOUT staring back to you. You don’t believe it? Try first, sure you ENJOY!!! *All Honest Members Will be Paid* Members • FREE Membership • *All Emails Worth $200* • *$500 signup bonus before 10000 members!* • No downline required for payout! • *$15000 Payout* • $10 referral bonus ! • *Fast Payments For Honest Members* • Payments are made via PayPal, eGold, MoneyBookers, StormPay, EvoCash, AnyPay, NetPay, Neteller, E-Bullion, Money Order or check! • International Members are Welcome! • Receive eMail on the best products • Receive eMail on the best opportunities • 4 Ref levels of commission under you *Get more details at:* http://boffopaidmail.com/pages/index.php?refid=wani282

1 0

[U-Boot] [RFC] - sanve the server's mac address...
by Robin Getz 23 Jul '09

23 Jul '09

Linux's netconsole works much better when you can pass it the MAC address of the server. (otherwise it just uses broadcast, which everyone else on my network complains about :) This sets the evn var "serveraddr" (to match ethaddr), so that you can pass it to linux with whatever bootargs you want to.... addnetconsole=set bootargs $(bootargs) netconsole=@$(ipaddr)/eth0,@$(serverip)/$(serveraddr) I'm sure this is white space damaged - but you get the idea... Index: net/net.c =================================================================== --- net/net.c (revision 1961) +++ net/net.c (working copy) @@ -1273,6 +1273,15 @@ /* are we waiting for a reply */ if (!NetArpWaitPacketIP || !NetArpWaitPacketMAC) break; + +#ifdef CONFIG_KEEP_SERVERADDR + if (NetServerIP == NetArpWaitPacketIP) { + char buf[20]; + sprintf(buf, "%pM", arp->ar_data); + setenv("serveraddr", buf); + } +#endif + #ifdef ET_DEBUG printf("Got ARP REPLY, set server/gtwy eth addr (%pM)\n", arp->ar_data)

4 16

[U-Boot] [PATCH v10] Marvell Kirkwood family SOC support
by Prafulla Wadaskar 23 Jul '09

23 Jul '09

Kirkwood family controllers are highly integrated SOCs based on Feroceon-88FR131/Sheeva-88SV131 cpu core. SOC versions supported:- 1) 88F6281-A0 define CONFIG_KW88F6281_A0 2) 88F6192-A0 define CONFIG_KW88F6192_A0 Other supported features:- 1) get_random_hex() fucntion 2) SPI port controller driver 3) PCI Express port initialization Contributors: Yotam Admon <yotam(a)marvell.com> Michael Blostein <michaelbl(a)marvell.com Reviewed-by: Ronen Shitrit <rshitrit(a)marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla(a)marvell.com> --- Change log: v2: crated arch-kirkwood and moved some header files there renamed and moved spi.c to drivers/spi/ renamed and moved serial.c to drivers/serial/ doimage utility removed soc_init.S renamed as lowlevel_init.S debug prints removed v3: lowlevel_init.S converted to lowlevel_init.c removed BITxx macros, removed entire assembly code Added CONFIG_ARCH_LOWLEVE_INIT support for arm926ejs core updated as per review commens for v2 v4: updated as per review comments for v3 print_cpuinfo used to display Soc info arch_misc_init support created and used for lib_arm mandatory readl/write macros used asm/cache.h asm/arch/spi.h asm//arch/serial.h created and used v5: updated as per review comments for v4 cosmetic updates, arch_misc_init and arch_cpu_init used start.S updated to call arch_lowlevel_init in case if lowlevl_init is skipped bug fix in cpu.c v6: lowlevel_init.S removed code moved under arch_cpu_init v7: include <asm/arch/kirkwood.h> added to each c file reference removed from include/asm/config.h arch_misc_init defination kept as it is in include/common.h bugfixed in get_random_hex function v7.1: u-boot.lds moved from board specific to kirkwood v8: mpp configuration added u-boot.lsd and config.mk removed serial driver removed and used ns16550 register offsets replaced by c struct updated as per review comments for v7 v9: updated as per v8 review comments removed all (u32) typecasts spi driver bugfix and magic constants removed tabs used for all indentation v10: struct for nand flash registers added cpu/arm926ejs/kirkwood/Makefile | 49 +++++ cpu/arm926ejs/kirkwood/cpu.c | 316 +++++++++++++++++++++++++++++ cpu/arm926ejs/kirkwood/dram.c | 58 ++++++ cpu/arm926ejs/kirkwood/mpp.c | 80 ++++++++ cpu/arm926ejs/kirkwood/timer.c | 168 +++++++++++++++ drivers/serial/serial.c | 3 + drivers/spi/Makefile | 1 + drivers/spi/kirkwood_spi.c | 185 +++++++++++++++++ include/asm-arm/arch-kirkwood/cpu.h | 149 ++++++++++++++ include/asm-arm/arch-kirkwood/kirkwood.h | 69 +++++++ include/asm-arm/arch-kirkwood/kw88f6192.h | 37 ++++ include/asm-arm/arch-kirkwood/kw88f6281.h | 37 ++++ include/asm-arm/arch-kirkwood/mpp.h | 303 +++++++++++++++++++++++++++ include/asm-arm/arch-kirkwood/spi.h | 56 +++++ include/asm-arm/cache.h | 41 ++++ include/common.h | 1 + lib_arm/board.c | 4 + 17 files changed, 1557 insertions(+), 0 deletions(-) create mode 100644 cpu/arm926ejs/kirkwood/Makefile create mode 100644 cpu/arm926ejs/kirkwood/cpu.c create mode 100644 cpu/arm926ejs/kirkwood/dram.c create mode 100644 cpu/arm926ejs/kirkwood/mpp.c create mode 100644 cpu/arm926ejs/kirkwood/timer.c create mode 100644 drivers/spi/kirkwood_spi.c create mode 100644 include/asm-arm/arch-kirkwood/cpu.h create mode 100644 include/asm-arm/arch-kirkwood/kirkwood.h create mode 100644 include/asm-arm/arch-kirkwood/kw88f6192.h create mode 100644 include/asm-arm/arch-kirkwood/kw88f6281.h create mode 100644 include/asm-arm/arch-kirkwood/mpp.h create mode 100644 include/asm-arm/arch-kirkwood/spi.h create mode 100644 include/asm-arm/cache.h diff --git a/cpu/arm926ejs/kirkwood/Makefile b/cpu/arm926ejs/kirkwood/Makefile new file mode 100644 index 0000000..b966ea1 --- /dev/null +++ b/cpu/arm926ejs/kirkwood/Makefile @@ -0,0 +1,49 @@ +# +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Prafulla Wadaskar <prafulla(a)marvell.com> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(SOC).a + +COBJS-y = dram.o +COBJS-y += cpu.o +COBJS-y += mpp.o +COBJS-y += timer.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS-y)) + +all: $(obj).depend $(LIB) + +$(LIB): $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/cpu/arm926ejs/kirkwood/cpu.c b/cpu/arm926ejs/kirkwood/cpu.c new file mode 100644 index 0000000..1286cac --- /dev/null +++ b/cpu/arm926ejs/kirkwood/cpu.c @@ -0,0 +1,316 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar <prafulla(a)marvell.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include <common.h> +#include <netdev.h> +#include <asm/cache.h> +#include <u-boot/md5.h> +#include <asm/arch/kirkwood.h> + +#define BUFLEN 16 + +void reset_cpu(unsigned long ignored) +{ + struct kwcpu_registers *cpureg = + (struct kwcpu_registers *)KW_CPU_REG_BASE; + + writel(readl(&cpureg->rstoutn_mask) | (1 << 2), + &cpureg->rstoutn_mask); + writel(readl(&cpureg->sys_soft_rst) | 1, + &cpureg->sys_soft_rst); + while (1) ; +} + +/* + * Generates Ramdom hex number reading some time varient system registers + * and using md5 algorithm + */ +unsigned char get_random_hex(void) +{ + int i; + u32 inbuf[BUFLEN]; + u8 outbuf[BUFLEN]; + + /* + * in case of 88F6281/88F6192 A0, + * Bit7 need to reset to generate random values in KW_REG_UNDOC_0x1470 + * Soc reg offsets KW_REG_UNDOC_0x1470 and KW_REG_UNDOC_0x1478 are reserved regs and + * Does not have names at this moment (no errata available) + */ + writel(readl(KW_REG_UNDOC_0x1478) & ~(1 << 7), KW_REG_UNDOC_0x1478); + for (i = 0; i < BUFLEN; i++) { + inbuf[i] = readl(KW_REG_UNDOC_0x1470); + } + md5((u8 *) inbuf, (BUFLEN * sizeof(u32)), outbuf); + return outbuf[outbuf[7] % 0x0f]; +} + +/* + * Window Size + * Used with the Base register to set the address window size and location. + * Must be programmed from LSB to MSB as sequence of 1’s followed by + * sequence of 0’s. The number of 1’s specifies the size of the window in + * 64 KByte granularity (e.g., a value of 0x00FF specifies 256 = 16 MByte). + * NOTE: A value of 0x0 specifies 64-KByte size. + */ +static unsigned int kw_winctrl_calcsize(unsigned int sizeval) +{ + int i; + unsigned int j = 0; + + for (i = 0; i < (sizeval / 0x10000); i++) + j |= (1 << i); + + return (0x0000ffff & j); +} + +/* prepares data to be loaded in win_Ctrl register */ +#define KWCPU_WIN_CTRL_DATA(size, target, attr, en) (en | (target << 4) \ + | (attr << 8) | (kw_winctrl_calcsize(size) << 16)) + +/* + * kw_config_adr_windows - Configure address Windows + * + * There are 7 address windows supported by Kirkwood Soc to addess different + * devices. Each window can be configured for size, BAR and remap addr + * Below configuration is standard for most of the cases + * + * Reference Documentation: + * Mbus-L to Mbus Bridge Registers Configuration. + * (Sec 25.1 and 25.3 of Datasheet) + */ +int kw_config_adr_windows(void) +{ + struct kwwin_registers *winregs = + (struct kwwin_registers *)KW_CPU_WIN_BASE; + + writel(KWCPU_WIN_CTRL_DATA(0xc0000, KWCPU_TARGET_PCIE, + KWCPU_ATTR_PCIE_MEM, KWCPU_WIN_ENABLE), + &winregs[0].ctrl); + + writel(0x90000000, &winregs[0].base); + writel(0x90000000, &winregs[0].remap_lo); + writel(0x00000000, &winregs[0].remap_hi); + + writel(KWCPU_WIN_CTRL_DATA(0x70000, KWCPU_TARGET_MEMORY, + KWCPU_ATTR_NANDFLASH, KWCPU_WIN_ENABLE), + &winregs[1].ctrl); + writel(0xF9000000, &winregs[1].base); + writel(0xF9000000, &winregs[1].remap_lo); + writel(0x00000000, &winregs[1].remap_hi); + + writel(KWCPU_WIN_CTRL_DATA(0x80000, KWCPU_TARGET_PCIE, + KWCPU_ATTR_PCIE_IO, KWCPU_WIN_ENABLE), + &winregs[2].ctrl); + writel(0xF0000000, &winregs[2].base); + writel(0xC0000000, &winregs[2].remap_lo); + writel(0x00000000, &winregs[2].remap_hi); + + writel(KWCPU_WIN_CTRL_DATA(0x80000, KWCPU_TARGET_MEMORY, + KWCPU_ATTR_SPIFLASH, KWCPU_WIN_ENABLE), + &winregs[3].ctrl); + writel(0xF8000000, &winregs[3].base); + writel(0x00000000, &winregs[3].remap_lo); + writel(0x00000000, &winregs[3].remap_hi); + + writel(KWCPU_WIN_CTRL_DATA(0x80000, KWCPU_TARGET_MEMORY, + KWCPU_ATTR_BOOTROM, KWCPU_WIN_ENABLE), + &winregs[4].ctrl); + writel(0xFF000000, &winregs[4].base); + writel(0x00000000, &winregs[4].remap_lo); + writel(0x00000000, &winregs[4].remap_hi); + + writel(KWCPU_WIN_CTRL_DATA(0xb0000, KWCPU_TARGET_MEMORY, + KWCPU_ATTR_SPIFLASH, KWCPU_WIN_DISABLE), + &winregs[5].ctrl); + writel(0xE8000000, &winregs[5].base); + writel(0x00000000, &winregs[5].remap_lo); + writel(0x00000000, &winregs[5].remap_hi); + + writel(KWCPU_WIN_CTRL_DATA(0xb0000, KWCPU_TARGET_MEMORY, + KWCPU_ATTR_BOOTROM, KWCPU_WIN_DISABLE), + &winregs[6].ctrl); + writel(0xF0000000, &winregs[6].base); + writel(0x00000000, &winregs[6].remap_lo); + writel(0x00000000, &winregs[6].remap_hi); + + writel(KWCPU_WIN_CTRL_DATA(0x0, KWCPU_TARGET_SASRAM, KWCPU_ATTR_SASRAM, + KWCPU_WIN_ENABLE), &winregs[7].ctrl); + writel(0xFB000000, &winregs[7].base); + writel(0x00000000, &winregs[7].remap_lo); + writel(0x00000000, &winregs[7].remap_hi); + + return 0; +} + +/* + * kw_config_gpio - GPIO configuration + */ +void kw_config_gpio(u32 gpp0_oe_val, u32 gpp1_oe_val, u32 gpp0_oe, u32 gpp1_oe) +{ + struct kwgpio_registers *gpio0reg = + (struct kwgpio_registers *)KW_GPIO0_BASE; + struct kwgpio_registers *gpio1reg = + (struct kwgpio_registers *)KW_GPIO1_BASE; + + /* Init GPIOS to default values as per board requirement */ + writel(gpp0_oe_val, &gpio0reg->dout); + writel(gpp1_oe_val, &gpio1reg->dout); + writel(gpp0_oe, &gpio0reg->oe); + writel(gpp1_oe, &gpio1reg->oe); +} + +/* + * kw_config_mpp - Multi-Purpose Pins Functionality configuration + * + * Each MPP can be configured to different functionality through + * MPP control register, ref (sec 6.1 of kirkwood h/w specification) + * + * There are maximum 64 Multi-Pourpose Pins on Kirkwood + * Each MPP functionality can be configuration by a 4bit value + * of MPP control reg, the value and associated functionality depends + * upon used SoC varient + */ +int kw_config_mpp(u32 mpp0_7, u32 mpp8_15, u32 mpp16_23, u32 mpp24_31, + u32 mpp32_39, u32 mpp40_47, u32 mpp48_55) +{ + u32 *mppreg = (u32 *) KW_MPP_BASE; + + /* program mpp registers */ + writel(mpp0_7, &mppreg[0]); + writel(mpp8_15, &mppreg[1]); + writel(mpp16_23, &mppreg[2]); + writel(mpp24_31, &mppreg[3]); + writel(mpp32_39, &mppreg[4]); + writel(mpp40_47, &mppreg[5]); + writel(mpp48_55, &mppreg[6]); + return 0; +} + +#if defined(CONFIG_DISPLAY_CPUINFO) +int print_cpuinfo(void) +{ + char *name = "Unknown"; + + switch (readl(KW_REG_DEVICE_ID) & 0x03) { + case 1: + name = "88F6192_A0"; + break; + case 2: + name = "88F6281_A0"; + break; + default: + printf("SoC: Unsupported Kirkwood\n"); + return -1; + } + printf("SoC: Kirkwood %s\n", name); + return 0; +} +#endif /* CONFIG_DISPLAY_CPUINFO */ + +#ifdef CONFIG_ARCH_CPU_INIT +int arch_cpu_init(void) +{ + u32 reg; + struct kwcpu_registers *cpureg = + (struct kwcpu_registers *)KW_CPU_REG_BASE; + + /* Linux expects` the internal registers to be at 0xf1000000 */ + writel(KW_REGS_PHY_BASE, KW_OFFSET_REG); + + /* Enable and invalidate L2 cache in write through mode */ + writel(readl(&cpureg->l2_cfg) | 0x18, &cpureg->l2_cfg); + invalidate_l2_cache(); + + kw_config_adr_windows(); + +#ifdef CONFIG_KIRKWOOD_RGMII_PAD_1V8 + /* + * Configures the I/O voltage of the pads connected to Egigabit + * Ethernet interface to 1.8V + * By defult it is set to 3.3V + */ + reg = readl(KW_REG_MPP_OUT_DRV_REG); + reg |= (1 << 7); + writel(reg, KW_REG_MPP_OUT_DRV_REG); +#endif +#ifdef CONFIG_KIRKWOOD_EGIGA_INIT + /* + * Set egiga port0/1 in normal functional mode + * This is required becasue on kirkwood by default ports are in reset mode + * OS egiga driver may not have provision to set them in normal mode + * and if u-boot is build without network support, network may fail at OS level + */ + reg = readl(KWGBE_PORT_SERIAL_CONTROL1_REG(0)); + reg &= ~(1 << 4); /* Clear PortReset Bit */ + writel(reg, (KWGBE_PORT_SERIAL_CONTROL1_REG(0))); + reg = readl(KWGBE_PORT_SERIAL_CONTROL1_REG(1)); + reg &= ~(1 << 4); /* Clear PortReset Bit */ + writel(reg, (KWGBE_PORT_SERIAL_CONTROL1_REG(1))); +#endif +#ifdef CONFIG_KIRKWOOD_PCIE_INIT + /* + * Enable PCI Express Port0 + */ + reg = readl(&cpureg->ctrl_stat); + reg |= (1 << 0); /* Set PEX0En Bit */ + writel(reg, &cpureg->ctrl_stat); +#endif + return 0; +} +#endif /* CONFIG_ARCH_CPU_INIT */ + +/* + * SOC specific misc init + */ +#if defined(CONFIG_ARCH_MISC_INIT) +int arch_misc_init(void) +{ + volatile u32 temp; + + /*CPU streaming & write allocate */ + temp = readfr_extra_feature_reg(); + temp &= ~(1 << 28); /* disable wr alloc */ + writefr_extra_feature_reg(temp); + + temp = readfr_extra_feature_reg(); + temp &= ~(1 << 29); /* streaming disabled */ + writefr_extra_feature_reg(temp); + + /* L2Cache settings */ + temp = readfr_extra_feature_reg(); + /* Disable L2C pre fetch - Set bit 24 */ + temp |= (1 << 24); + /* enable L2C - Set bit 22 */ + temp |= (1 << 22); + writefr_extra_feature_reg(temp); + + icache_enable(); + /* Change reset vector to address 0x0 */ + temp = get_cr(); + set_cr(temp & ~CR_V); + + return 0; +} +#endif /* CONFIG_ARCH_MISC_INIT */ diff --git a/cpu/arm926ejs/kirkwood/dram.c b/cpu/arm926ejs/kirkwood/dram.c new file mode 100644 index 0000000..3ec0548 --- /dev/null +++ b/cpu/arm926ejs/kirkwood/dram.c @@ -0,0 +1,58 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar <prafulla(a)marvell.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include <config.h> +#include <asm/arch/kirkwood.h> + +#define KW_REG_CPUCS_WIN_BAR(x) (KW_REGISTER(0x1500) + (x * 0x08)) +#define KW_REG_CPUCS_WIN_SZ(x) (KW_REGISTER(0x1504) + (x * 0x08)) +/* + * kw_sdram_bar - reads SDRAM Base Address Register + */ +u32 kw_sdram_bar(enum memory_bank bank) +{ + u32 result = 0; + u32 enable = 0x01 & readl(KW_REG_CPUCS_WIN_SZ(bank)); + + if ((!enable) || (bank > BANK3)) + return 0; + + result = readl(KW_REG_CPUCS_WIN_BAR(bank)); + return result; +} + +/* + * kw_sdram_bs - reads SDRAM Bank size + */ +u32 kw_sdram_bs(enum memory_bank bank) +{ + u32 result = 0; + u32 enable = 0x01 & readl(KW_REG_CPUCS_WIN_SZ(bank)); + + if ((!enable) || (bank > BANK3)) + return 0; + result = 0xff000000 & readl(KW_REG_CPUCS_WIN_SZ(bank)); + result += 0x01000000; + return result; +} diff --git a/cpu/arm926ejs/kirkwood/mpp.c b/cpu/arm926ejs/kirkwood/mpp.c new file mode 100644 index 0000000..b2f0ad5 --- /dev/null +++ b/cpu/arm926ejs/kirkwood/mpp.c @@ -0,0 +1,80 @@ +/* + * arch/arm/mach-kirkwood/mpp.c + * + * MPP functions for Marvell Kirkwood SoCs + * Referenced from Linux kernel source + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <common.h> +#include <asm/arch/kirkwood.h> +#include <asm/arch/mpp.h> + +static u32 kirkwood_variant(void) +{ + switch (readl(KW_REG_DEVICE_ID) & 0x03) { + case 1: + return MPP_F6192_MASK; + case 2: + return MPP_F6281_MASK; + default: + debug("MPP setup: unknown kirkwood variant\n"); + return 0; + } +} + +#define MPP_CTRL(i) (KW_MPP_BASE + (i* 4)) +#define MPP_NR_REGS (1 + MPP_MAX/8) + +void kirkwood_mpp_conf(u32 *mpp_list) +{ + u32 mpp_ctrl[MPP_NR_REGS]; + unsigned int variant_mask; + int i; + + variant_mask = kirkwood_variant(); + if (!variant_mask) + return; + + debug( "initial MPP regs:"); + for (i = 0; i < MPP_NR_REGS; i++) { + mpp_ctrl[i] = readl(MPP_CTRL(i)); + debug(" %08x", mpp_ctrl[i]); + } + debug("\n"); + + + while (*mpp_list) { + unsigned int num = MPP_NUM(*mpp_list); + unsigned int sel = MPP_SEL(*mpp_list); + int shift; + + if (num > MPP_MAX) { + debug("kirkwood_mpp_conf: invalid MPP " + "number (%u)\n", num); + continue; + } + if (!(*mpp_list & variant_mask)) { + debug("kirkwood_mpp_conf: requested MPP%u config " + "unavailable on this hardware\n", num); + continue; + } + + shift = (num & 7) << 2; + mpp_ctrl[num / 8] &= ~(0xf << shift); + mpp_ctrl[num / 8] |= sel << shift; + + mpp_list++; + } + + debug(" final MPP regs:"); + for (i = 0; i < MPP_NR_REGS; i++) { + writel(mpp_ctrl[i], MPP_CTRL(i)); + debug(" %08x", mpp_ctrl[i]); + } + debug("\n"); + +} diff --git a/cpu/arm926ejs/kirkwood/timer.c b/cpu/arm926ejs/kirkwood/timer.c new file mode 100644 index 0000000..5c39ee8 --- /dev/null +++ b/cpu/arm926ejs/kirkwood/timer.c @@ -0,0 +1,168 @@ +/* + * Copyright (C) Marvell International Ltd. and its affiliates + * Prafulla Wadaskar <prafulla(a)marvell.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include <common.h> +#include <asm/arch/kirkwood.h> + +#define UBOOT_CNTR 0 /* counter to use for uboot timer */ + +/* Timer reload and current value registers */ +struct kwtmr_val { + u32 reload; /* Timer reload reg */ + u32 val; /* Timer value reg */ +}; + +/* Timer registers */ +struct kwtmr_registers { + u32 ctrl; /* Timer control reg */ + u32 pad[3]; + struct kwtmr_val tmr[2]; + u32 wdt_reload; + u32 wdt_val; +}; + +struct kwtmr_registers *kwtmr_regs = (struct kwtmr_registers *)KW_TIMER_BASE; + +/* + * ARM Timers Registers Map + */ +#define CNTMR_CTRL_REG &kwtmr_regs->ctrl +#define CNTMR_RELOAD_REG(tmrnum) &kwtmr_regs->tmr[tmrnum].reload +#define CNTMR_VAL_REG(tmrnum) &kwtmr_regs->tmr[tmrnum].val + +/* + * ARM Timers Control Register + * CPU_TIMERS_CTRL_REG (CTCR) + */ +#define CTCR_ARM_TIMER_EN_OFFS(cntr) (cntr * 2) +#define CTCR_ARM_TIMER_EN_MASK(cntr) (1 << CTCR_ARM_TIMER_EN_OFFS) +#define CTCR_ARM_TIMER_EN(cntr) (1 << CTCR_ARM_TIMER_EN_OFFS(cntr)) +#define CTCR_ARM_TIMER_DIS(cntr) (0 << CTCR_ARM_TIMER_EN_OFFS(cntr)) + +#define CTCR_ARM_TIMER_AUTO_OFFS(cntr) ((cntr * 2) + 1) +#define CTCR_ARM_TIMER_AUTO_MASK(cntr) (1 << 1) +#define CTCR_ARM_TIMER_AUTO_EN(cntr) (1 << CTCR_ARM_TIMER_AUTO_OFFS(cntr)) +#define CTCR_ARM_TIMER_AUTO_DIS(cntr) (0 << CTCR_ARM_TIMER_AUTO_OFFS(cntr)) + +/* + * ARM Timer\Watchdog Reload Register + * CNTMR_RELOAD_REG (TRR) + */ +#define TRG_ARM_TIMER_REL_OFFS 0 +#define TRG_ARM_TIMER_REL_MASK 0xffffffff + +/* + * ARM Timer\Watchdog Register + * CNTMR_VAL_REG (TVRG) + */ +#define TVR_ARM_TIMER_OFFS 0 +#define TVR_ARM_TIMER_MASK 0xffffffff +#define TVR_ARM_TIMER_MAX 0xffffffff +#define TIMER_LOAD_VAL 0xffffffff + +#define READ_TIMER (readl(CNTMR_VAL_REG(UBOOT_CNTR)) / \ + (CONFIG_SYS_TCLK / 1000)) + +static ulong timestamp; +static ulong lastdec; + +void reset_timer_masked(void) +{ + /* reset time */ + lastdec = READ_TIMER; + timestamp = 0; +} + +ulong get_timer_masked(void) +{ + ulong now = READ_TIMER; + + if (lastdec >= now) { + /* normal mode */ + timestamp += lastdec - now; + } else { + /* we have an overflow ... */ + timestamp += lastdec + + (TIMER_LOAD_VAL / (CONFIG_SYS_TCLK / 1000)) - now; + } + lastdec = now; + + return timestamp; +} + +void reset_timer(void) +{ + reset_timer_masked(); +} + +ulong get_timer(ulong base) +{ + return get_timer_masked() - base; +} + +void set_timer(ulong t) +{ + timestamp = t; +} + +void udelay(unsigned long usec) +{ + uint current; + ulong delayticks; + + current = readl(CNTMR_VAL_REG(UBOOT_CNTR)); + delayticks = (usec * (CONFIG_SYS_TCLK / 1000000)); + + if (current < delayticks) { + delayticks -= current; + while (readl(CNTMR_VAL_REG(UBOOT_CNTR)) < current) ; + while ((TIMER_LOAD_VAL - delayticks) < + readl(CNTMR_VAL_REG(UBOOT_CNTR))) ; + } else { + while (readl(CNTMR_VAL_REG(UBOOT_CNTR)) > + (current - delayticks)) ; + } +} + +/* + * init the counter + */ +int timer_init(void) +{ + unsigned int cntmrctrl; + + /* load value into timer */ + writel(TIMER_LOAD_VAL, CNTMR_RELOAD_REG(UBOOT_CNTR)); + writel(TIMER_LOAD_VAL, CNTMR_VAL_REG(UBOOT_CNTR)); + + /* enable timer in auto reload mode */ + cntmrctrl = readl(CNTMR_CTRL_REG); + cntmrctrl |= CTCR_ARM_TIMER_EN(UBOOT_CNTR); + cntmrctrl |= CTCR_ARM_TIMER_AUTO_EN(UBOOT_CNTR); + writel(cntmrctrl, CNTMR_CTRL_REG); + + /* init the timestamp and lastdec value */ + reset_timer_masked(); + + return 0; +} diff --git a/drivers/serial/serial.c b/drivers/serial/serial.c index 966df9a..dd5f332 100644 --- a/drivers/serial/serial.c +++ b/drivers/serial/serial.c @@ -27,6 +27,9 @@ #ifdef CONFIG_NS87308 #include <ns87308.h> #endif +#ifdef CONFIG_KIRKWOOD +#include <asm/arch/kirkwood.h> +#endif #if defined (CONFIG_SERIAL_MULTI) #include <serial.h> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 1350f3e..7ffa47d 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -28,6 +28,7 @@ LIB := $(obj)libspi.a COBJS-$(CONFIG_ATMEL_DATAFLASH_SPI) += atmel_dataflash_spi.o COBJS-$(CONFIG_ATMEL_SPI) += atmel_spi.o COBJS-$(CONFIG_BFIN_SPI) += bfin_spi.o +COBJS-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o COBJS-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o COBJS-$(CONFIG_MXC_SPI) += mxc_spi.o COBJS-$(CONFIG_SOFT_SPI) += soft_spi.o diff --git a/drivers/spi/kirkwood_spi.c b/drivers/spi/kirkwood_spi.c new file mode 100644 index 0000000..9d16e9b --- /dev/null +++ b/drivers/spi/kirkwood_spi.c @@ -0,0 +1,185 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar <prafulla(a)marvell.com> + * + * Derived from drivers/spi/mpc8xxx_spi.c + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include <common.h> +#include <malloc.h> +#include <spi.h> +#include <asm/arch/kirkwood.h> +#include <asm/arch/spi.h> +#include <asm/arch/mpp.h> + +static struct kwspi_registers *spireg = (struct kwspi_registers *)KW_SPI_BASE; + +struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, + unsigned int max_hz, unsigned int mode) +{ + struct spi_slave *slave; + u32 data; + u32 kwspi_mpp_config[] = { + MPP0_GPIO, + MPP7_SPI_SCn, + 0 + }; + + if (!spi_cs_is_valid(bus, cs)) + return NULL; + + slave = malloc(sizeof(struct spi_slave)); + if (!slave) + return NULL; + + slave->bus = bus; + slave->cs = cs; + + writel(~KWSPI_CSN_ACT | KWSPI_SMEMRDY, &spireg->ctrl); + + /* calculate spi clock prescaller using max_hz */ + data = ((CONFIG_SYS_TCLK / 2) / max_hz) & KWSPI_CLKPRESCL_MASK; + data |= 0x10; + + /* program spi clock prescaller using max_hz */ + writel(KWSPI_ADRLEN_3BYTE | data, &spireg->cfg); + debug("data = 0x%08x \n", data); + + writel(KWSPI_SMEMRDIRQ, &spireg->irq_cause); + writel(KWSPI_IRQMASK, spireg->irq_mask); + + /* program mpp registers to select SPI_CSn */ + if (cs) { + kwspi_mpp_config[0] = MPP0_GPIO; + kwspi_mpp_config[1] = MPP7_SPI_SCn; + } else { + kwspi_mpp_config[0] = MPP0_SPI_SCn; + kwspi_mpp_config[1] = MPP7_GPO; + } + kirkwood_mpp_conf(kwspi_mpp_config); + + return slave; +} + +void spi_free_slave(struct spi_slave *slave) +{ + free(slave); +} + +int spi_claim_bus(struct spi_slave *slave) +{ + return 0; +} + +void spi_release_bus(struct spi_slave *slave) +{ +} + +#ifndef CONFIG_SPI_CS_IS_VALID +/* + * you can define this function board specific + * define above CONFIG in board specific config file and + * provide the function in board specific src file + */ +int spi_cs_is_valid(unsigned int bus, unsigned int cs) +{ + return (bus == 0 && (cs == 0 || cs == 1)); +} +#endif + +void spi_cs_activate(struct spi_slave *slave) +{ + writel(readl(&spireg->ctrl) | KWSPI_IRQUNMASK, &spireg->ctrl); +} + +void spi_cs_deactivate(struct spi_slave *slave) +{ + writel(readl(&spireg->ctrl) & KWSPI_IRQMASK, &spireg->ctrl); +} + +int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, + void *din, unsigned long flags) +{ + unsigned int tmpdout, tmpdin; + int tm, isread = 0; + + debug("spi_xfer: slave %u:%u dout %08X din %08X bitlen %u\n", + slave->bus, slave->cs, dout, din, bitlen); + + if (flags & SPI_XFER_BEGIN) + spi_cs_activate(slave); + + /* + * handle data in 8-bit chunks + * TBD: 2byte xfer mode to be enabled + */ + writel(((readl(&spireg->cfg) & ~KWSPI_XFERLEN_MASK) | + KWSPI_XFERLEN_1BYTE), &spireg->cfg); + + while (bitlen > 4) { + debug("loopstart bitlen %d\n", bitlen); + tmpdout = 0; + + /* Shift data so it's msb-justified */ + if (dout) + tmpdout = *(u32 *) dout & 0x0ff; + + writel(~KWSPI_SMEMRDIRQ, &spireg->irq_cause); + writel(tmpdout, &spireg->dout); /* Write the data out */ + debug("*** spi_xfer: ... %08x written, bitlen %d\n", + tmpdout, bitlen); + + /* + * Wait for SPI transmit to get out + * or time out (1 second = 1000 ms) + * The NE event must be read and cleared first + */ + for (tm = 0, isread = 0; tm < KWSPI_TIMEOUT; ++tm) { + if (readl(&spireg->irq_cause) & KWSPI_SMEMRDIRQ) { + isread = 1; + tmpdin = readl(&spireg->din); + debug + ("spi_xfer: din %08x..%08x read\n", + din, tmpdin); + + if (din) { + *((u8 *) din) = (u8) tmpdin; + din += 1; + } + if (dout) + dout += 1; + bitlen -= 8; + } + if (isread) + break; + } + if (tm >= KWSPI_TIMEOUT) + printf("*** spi_xfer: Time out during SPI transfer\n"); + + debug("loopend bitlen %d\n", bitlen); + } + + if (flags & SPI_XFER_END) + spi_cs_deactivate(slave); + + return 0; +} diff --git a/include/asm-arm/arch-kirkwood/cpu.h b/include/asm-arm/arch-kirkwood/cpu.h new file mode 100644 index 0000000..635bd8f --- /dev/null +++ b/include/asm-arm/arch-kirkwood/cpu.h @@ -0,0 +1,149 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar <prafulla(a)marvell.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef _KWCPU_H +#define _KWCPU_H + +#include <asm/system.h> + +#ifndef __ASSEMBLY__ + +#define KWGBE_PORT_SERIAL_CONTROL1_REG(_x) \ + ((_x ? KW_EGIGA0_BASE : KW_EGIGA1_BASE) + 0x44c) + +#define KW_REG_DEVICE_ID (KW_MPP_BASE + 0x34) +#define KW_REG_MPP_OUT_DRV_REG (KW_MPP_BASE + 0xE0) + +enum memory_bank { + BANK0, + BANK1, + BANK2, + BANK3 +}; + +enum kwcpu_winen { + KWCPU_WIN_DISABLE, + KWCPU_WIN_ENABLE +}; + +enum kwcpu_target { + KWCPU_TARGET_RESERVED, + KWCPU_TARGET_MEMORY, + KWCPU_TARGET_1RESERVED, + KWCPU_TARGET_SASRAM, + KWCPU_TARGET_PCIE +}; + +enum kwcpu_attrib { + KWCPU_ATTR_SASRAM = 0x01, + KWCPU_ATTR_NANDFLASH = 0x2f, + KWCPU_ATTR_SPIFLASH = 0x1e, + KWCPU_ATTR_BOOTROM = 0x1d, + KWCPU_ATTR_PCIE_IO = 0xe0, + KWCPU_ATTR_PCIE_MEM = 0xe8 +}; + +/* + * read feroceon/sheeva core extra feature register + * using co-proc instruction + */ +static inline unsigned int readfr_extra_feature_reg(void) +{ + unsigned int val; + asm volatile ("mrc p15, 1, %0, c15, c1, 0 @ readfr exfr":"=r" + (val)::"cc"); + return val; +} + +/* + * write feroceon/sheeva core extra feature register + * using co-proc instruction + */ +static inline void writefr_extra_feature_reg(unsigned int val) +{ + asm volatile ("mcr p15, 1, %0, c15, c1, 0 @ writefr exfr"::"r" + (val):"cc"); + isb(); +} + +/* + * Register structures + */ +struct kwgpio_registers { + u32 dout; + u32 oe; + u32 blink_en; + u32 din_pol; + u32 din; + u32 irq_cause; + u32 irq_mask; + u32 irq_level; +}; + +struct kwwin_registers { + u32 ctrl; + u32 base; + u32 remap_lo; + u32 remap_hi; +}; + +/* CPU control and status registers */ +struct kwcpu_registers { + u32 config; /*0x20100 */ + u32 ctrl_stat; /*0x20104 */ + u32 rstoutn_mask; /* 0x20108 */ + u32 sys_soft_rst; /* 0x2010C */ + u32 ahb_mbus_cause_irq; /* 0x20110 */ + u32 ahb_mbus_mask_irq; /* 0x20114 */ + u32 pad1[2]; + u32 ftdll_config; /* 0x20120 */ + u32 pad2; + u32 l2_cfg; /* 0x20128 */ +}; + +/* NAND flash registers */ +struct kwnandf_registers { + u32 rd_params; /* 0x10418 */ + u32 wr_param; /* 0x1041c */ + u8 pag[0x10470 - 0x1041c -4]; + u32 ctrl; /* 0x10470 */ +}; + +/* + * functions + */ +void reset_cpu(unsigned long ignored); +unsigned char get_random_hex(void); +unsigned int kw_sdram_bar(enum memory_bank bank); +unsigned int kw_sdram_bs(enum memory_bank bank); +int kw_config_adr_windows(void); +void kw_config_gpio(unsigned int gpp0_oe_val, unsigned int gpp1_oe_val, + unsigned int gpp0_oe, unsigned int gpp1_oe); +int kw_config_mpp(unsigned int mpp0_7, unsigned int mpp8_15, + unsigned int mpp16_23, unsigned int mpp24_31, + unsigned int mpp32_39, unsigned int mpp40_47, + unsigned int mpp48_55); +#endif /* __ASSEMBLY__ */ + +#endif /* _KWCPU_H */ diff --git a/include/asm-arm/arch-kirkwood/kirkwood.h b/include/asm-arm/arch-kirkwood/kirkwood.h new file mode 100644 index 0000000..f026b9c --- /dev/null +++ b/include/asm-arm/arch-kirkwood/kirkwood.h @@ -0,0 +1,69 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar <prafulla(a)marvell.com> + * + * Header file for the Marvell's Feroceon CPU core. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef _ASM_ARCH_KIRKWOOD_H +#define _ASM_ARCH_KIRKWOOD_H + +#ifndef __ASSEMBLY__ +#include <asm/types.h> +#include <asm/io.h> +#endif /* __ASSEMBLY__ */ + +#if defined (CONFIG_FEROCEON_88FR131) || defined (CONFIG_SHEEVA_88SV131) +#include <asm/arch/cpu.h> + +/* SOC specific definations */ +#define INTREG_BASE 0xd0000000 +#define KW_REGISTER(x) (KW_REGS_PHY_BASE + x) +#define KW_OFFSET_REG (INTREG_BASE + 0x20080) + +/* undocumented registers */ +#define KW_REG_UNDOC_0x1470 (KW_REGISTER(0x1470)) +#define KW_REG_UNDOC_0x1478 (KW_REGISTER(0x1478)) + +#define KW_UART0_BASE (KW_REGISTER(0x12000)) +#define KW_UART1_BASE (KW_REGISTER(0x13000)) +#define KW_MPP_BASE (KW_REGISTER(0x10000)) +#define KW_GPIO0_BASE (KW_REGISTER(0x10100)) +#define KW_GPIO1_BASE (KW_REGISTER(0x10140)) +#define KW_NANDF_BASE (KW_REGISTER(0x10418)) +#define KW_SPI_BASE (KW_REGISTER(0x10600)) +#define KW_CPU_WIN_BASE (KW_REGISTER(0x20000)) +#define KW_CPU_REG_BASE (KW_REGISTER(0x20100)) +#define KW_TIMER_BASE (KW_REGISTER(0x20300)) +#define KW_REG_PCIE_BASE (KW_REGISTER(0x40000)) +#define KW_EGIGA0_BASE (KW_REGISTER(0x72000)) +#define KW_EGIGA1_BASE (KW_REGISTER(0x76000)) + +#if defined (CONFIG_KW88F6281) +#include <asm/arch/kw88f6281.h> +#elif defined (CONFIG_KW88F6192) +#include <asm/arch/kw88f6192.h> +#else +#error "SOC Name not defined" +#endif /* CONFIG_KW88F6281 */ +#endif /* CONFIG_FEROCEON_88FR131 */ +#endif /* _ASM_ARCH_KIRKWOOD_H */ diff --git a/include/asm-arm/arch-kirkwood/kw88f6192.h b/include/asm-arm/arch-kirkwood/kw88f6192.h new file mode 100644 index 0000000..a2b1f96 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/kw88f6192.h @@ -0,0 +1,37 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar <prafulla(a)marvell.com> + * + * Header file for Feroceon CPU core 88FR131 Based KW88F6192 SOC. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef _CONFIG_KW88F6192_H +#define _CONFIG_KW88F6192_H + +/* SOC specific definations */ +#define KW88F6192_REGS_PHYS_BASE 0xf1000000 +#define KW_REGS_PHY_BASE KW88F6192_REGS_PHYS_BASE + +/* TCLK Core Clock defination */ +#define CONFIG_SYS_TCLK 166000000 /* 166MHz */ + +#endif /* _CONFIG_KW88F6192_H */ diff --git a/include/asm-arm/arch-kirkwood/kw88f6281.h b/include/asm-arm/arch-kirkwood/kw88f6281.h new file mode 100644 index 0000000..9b89b93 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/kw88f6281.h @@ -0,0 +1,37 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar <prafulla(a)marvell.com> + * + * Header file for Feroceon CPU core 88FR131 Based KW88F6281 SOC. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef _ASM_ARCH_KW88F6281_H +#define _ASM_ARCH_KW88F6281_H + +/* SOC specific definations */ +#define KW88F6281_REGS_PHYS_BASE 0xf1000000 +#define KW_REGS_PHY_BASE KW88F6281_REGS_PHYS_BASE + +/* TCLK Core Clock defination*/ +#define CONFIG_SYS_TCLK 200000000 /* 200MHz */ + +#endif /* _ASM_ARCH_KW88F6281_H */ diff --git a/include/asm-arm/arch-kirkwood/mpp.h b/include/asm-arm/arch-kirkwood/mpp.h new file mode 100644 index 0000000..e021a80 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/mpp.h @@ -0,0 +1,303 @@ +/* + * linux/arch/arm/mach-kirkwood/mpp.h -- Multi Purpose Pins + * + * Copyright 2009: Marvell Technology Group Ltd. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __KIRKWOOD_MPP_H +#define __KIRKWOOD_MPP_H + +#define MPP(_num, _sel, _in, _out, _F6180, _F6190, _F6192, _F6281) ( \ + /* MPP number */ ((_num) & 0xff) | \ + /* MPP select value */ (((_sel) & 0xf) << 8) | \ + /* may be input signal */ ((!!(_in)) << 12) | \ + /* may be output signal */ ((!!(_out)) << 13) | \ + /* available on F6180 */ ((!!(_F6180)) << 14) | \ + /* available on F6190 */ ((!!(_F6190)) << 15) | \ + /* available on F6192 */ ((!!(_F6192)) << 16) | \ + /* available on F6281 */ ((!!(_F6281)) << 17)) + +#define MPP_NUM(x) ((x) & 0xff) +#define MPP_SEL(x) (((x) >> 8) & 0xf) + + /* num sel i o 6180 6190 6192 6281 */ + +#define MPP_INPUT_MASK MPP( 0, 0x0, 1, 0, 0, 0, 0, 0 ) +#define MPP_OUTPUT_MASK MPP( 0, 0x0, 0, 1, 0, 0, 0, 0 ) + +#define MPP_F6180_MASK MPP( 0, 0x0, 0, 0, 1, 0, 0, 0 ) +#define MPP_F6190_MASK MPP( 0, 0x0, 0, 0, 0, 1, 0, 0 ) +#define MPP_F6192_MASK MPP( 0, 0x0, 0, 0, 0, 0, 1, 0 ) +#define MPP_F6281_MASK MPP( 0, 0x0, 0, 0, 0, 0, 0, 1 ) + +#define MPP0_GPIO MPP( 0, 0x0, 1, 1, 1, 1, 1, 1 ) +#define MPP0_NF_IO2 MPP( 0, 0x1, 1, 1, 1, 1, 1, 1 ) +#define MPP0_SPI_SCn MPP( 0, 0x2, 0, 1, 1, 1, 1, 1 ) + +#define MPP1_GPO MPP( 1, 0x0, 0, 1, 1, 1, 1, 1 ) +#define MPP1_NF_IO3 MPP( 1, 0x1, 1, 1, 1, 1, 1, 1 ) +#define MPP1_SPI_MOSI MPP( 1, 0x2, 0, 1, 1, 1, 1, 1 ) + +#define MPP2_GPO MPP( 2, 0x0, 0, 1, 1, 1, 1, 1 ) +#define MPP2_NF_IO4 MPP( 2, 0x1, 1, 1, 1, 1, 1, 1 ) +#define MPP2_SPI_SCK MPP( 2, 0x2, 0, 1, 1, 1, 1, 1 ) + +#define MPP3_GPO MPP( 3, 0x0, 0, 1, 1, 1, 1, 1 ) +#define MPP3_NF_IO5 MPP( 3, 0x1, 1, 1, 1, 1, 1, 1 ) +#define MPP3_SPI_MISO MPP( 3, 0x2, 1, 0, 1, 1, 1, 1 ) + +#define MPP4_GPIO MPP( 4, 0x0, 1, 1, 1, 1, 1, 1 ) +#define MPP4_NF_IO6 MPP( 4, 0x1, 1, 1, 1, 1, 1, 1 ) +#define MPP4_UART0_RXD MPP( 4, 0x2, 1, 0, 1, 1, 1, 1 ) +#define MPP4_SATA1_ACTn MPP( 4, 0x5, 0, 1, 0, 0, 1, 1 ) +#define MPP4_PTP_CLK MPP( 4, 0xd, 1, 0, 1, 1, 1, 1 ) + +#define MPP5_GPO MPP( 5, 0x0, 0, 1, 1, 1, 1, 1 ) +#define MPP5_NF_IO7 MPP( 5, 0x1, 1, 1, 1, 1, 1, 1 ) +#define MPP5_UART0_TXD MPP( 5, 0x2, 0, 1, 1, 1, 1, 1 ) +#define MPP5_PTP_TRIG_GEN MPP( 5, 0x4, 0, 1, 1, 1, 1, 1 ) +#define MPP5_SATA0_ACTn MPP( 5, 0x5, 0, 1, 0, 1, 1, 1 ) + +#define MPP6_SYSRST_OUTn MPP( 6, 0x1, 0, 1, 1, 1, 1, 1 ) +#define MPP6_SPI_MOSI MPP( 6, 0x2, 0, 1, 1, 1, 1, 1 ) +#define MPP6_PTP_TRIG_GEN MPP( 6, 0x3, 0, 1, 1, 1, 1, 1 ) + +#define MPP7_GPO MPP( 7, 0x0, 0, 1, 1, 1, 1, 1 ) +#define MPP7_PEX_RST_OUTn MPP( 7, 0x1, 0, 1, 1, 1, 1, 1 ) +#define MPP7_SPI_SCn MPP( 7, 0x2, 0, 1, 1, 1, 1, 1 ) +#define MPP7_PTP_TRIG_GEN MPP( 7, 0x3, 0, 1, 1, 1, 1, 1 ) + +#define MPP8_GPIO MPP( 8, 0x0, 1, 1, 1, 1, 1, 1 ) +#define MPP8_TW_SDA MPP( 8, 0x1, 1, 1, 1, 1, 1, 1 ) +#define MPP8_UART0_RTS MPP( 8, 0x2, 0, 1, 1, 1, 1, 1 ) +#define MPP8_UART1_RTS MPP( 8, 0x3, 0, 1, 1, 1, 1, 1 ) +#define MPP8_MII0_RXERR MPP( 8, 0x4, 1, 0, 0, 1, 1, 1 ) +#define MPP8_SATA1_PRESENTn MPP( 8, 0x5, 0, 1, 0, 0, 1, 1 ) +#define MPP8_PTP_CLK MPP( 8, 0xc, 1, 0, 1, 1, 1, 1 ) +#define MPP8_MII0_COL MPP( 8, 0xd, 1, 0, 1, 1, 1, 1 ) + +#define MPP9_GPIO MPP( 9, 0x0, 1, 1, 1, 1, 1, 1 ) +#define MPP9_TW_SCK MPP( 9, 0x1, 1, 1, 1, 1, 1, 1 ) +#define MPP9_UART0_CTS MPP( 9, 0x2, 1, 0, 1, 1, 1, 1 ) +#define MPP9_UART1_CTS MPP( 9, 0x3, 1, 0, 1, 1, 1, 1 ) +#define MPP9_SATA0_PRESENTn MPP( 9, 0x5, 0, 1, 0, 1, 1, 1 ) +#define MPP9_PTP_EVENT_REQ MPP( 9, 0xc, 1, 0, 1, 1, 1, 1 ) +#define MPP9_MII0_CRS MPP( 9, 0xd, 1, 0, 1, 1, 1, 1 ) + +#define MPP10_GPO MPP( 10, 0x0, 0, 1, 1, 1, 1, 1 ) +#define MPP10_SPI_SCK MPP( 10, 0x2, 0, 1, 1, 1, 1, 1 ) +#define MPP10_UART0_TXD MPP( 10, 0X3, 0, 1, 1, 1, 1, 1 ) +#define MPP10_SATA1_ACTn MPP( 10, 0x5, 0, 1, 0, 0, 1, 1 ) +#define MPP10_PTP_TRIG_GEN MPP( 10, 0xc, 0, 1, 1, 1, 1, 1 ) + +#define MPP11_GPIO MPP( 11, 0x0, 1, 1, 1, 1, 1, 1 ) +#define MPP11_SPI_MISO MPP( 11, 0x2, 1, 0, 1, 1, 1, 1 ) +#define MPP11_UART0_RXD MPP( 11, 0x3, 1, 0, 1, 1, 1, 1 ) +#define MPP11_PTP_EVENT_REQ MPP( 11, 0x4, 1, 0, 1, 1, 1, 1 ) +#define MPP11_PTP_TRIG_GEN MPP( 11, 0xc, 0, 1, 1, 1, 1, 1 ) +#define MPP11_PTP_CLK MPP( 11, 0xd, 1, 0, 1, 1, 1, 1 ) +#define MPP11_SATA0_ACTn MPP( 11, 0x5, 0, 1, 0, 1, 1, 1 ) + +#define MPP12_GPO MPP( 12, 0x0, 0, 1, 1, 1, 1, 1 ) +#define MPP12_SD_CLK MPP( 12, 0x1, 0, 1, 1, 1, 1, 1 ) + +#define MPP13_GPIO MPP( 13, 0x0, 1, 1, 1, 1, 1, 1 ) +#define MPP13_SD_CMD MPP( 13, 0x1, 1, 1, 1, 1, 1, 1 ) +#define MPP13_UART1_TXD MPP( 13, 0x3, 0, 1, 1, 1, 1, 1 ) + +#define MPP14_GPIO MPP( 14, 0x0, 1, 1, 1, 1, 1, 1 ) +#define MPP14_SD_D0 MPP( 14, 0x1, 1, 1, 1, 1, 1, 1 ) +#define MPP14_UART1_RXD MPP( 14, 0x3, 1, 0, 1, 1, 1, 1 ) +#define MPP14_SATA1_PRESENTn MPP( 14, 0x4, 0, 1, 0, 0, 1, 1 ) +#define MPP14_MII0_COL MPP( 14, 0xd, 1, 0, 1, 1, 1, 1 ) + +#define MPP15_GPIO MPP( 15, 0x0, 1, 1, 1, 1, 1, 1 ) +#define MPP15_SD_D1 MPP( 15, 0x1, 1, 1, 1, 1, 1, 1 ) +#define MPP15_UART0_RTS MPP( 15, 0x2, 0, 1, 1, 1, 1, 1 ) +#define MPP15_UART1_TXD MPP( 15, 0x3, 0, 1, 1, 1, 1, 1 ) +#define MPP15_SATA0_ACTn MPP( 15, 0x4, 0, 1, 0, 1, 1, 1 ) + +#define MPP16_GPIO MPP( 16, 0x0, 1, 1, 1, 1, 1, 1 ) +#define MPP16_SD_D2 MPP( 16, 0x1, 1, 1, 1, 1, 1, 1 ) +#define MPP16_UART0_CTS MPP( 16, 0x2, 1, 0, 1, 1, 1, 1 ) +#define MPP16_UART1_RXD MPP( 16, 0x3, 1, 0, 1, 1, 1, 1 ) +#define MPP16_SATA1_ACTn MPP( 16, 0x4, 0, 1, 0, 0, 1, 1 ) +#define MPP16_MII0_CRS MPP( 16, 0xd, 1, 0, 1, 1, 1, 1 ) + +#define MPP17_GPIO MPP( 17, 0x0, 1, 1, 1, 1, 1, 1 ) +#define MPP17_SD_D3 MPP( 17, 0x1, 1, 1, 1, 1, 1, 1 ) +#define MPP17_SATA0_PRESENTn MPP( 17, 0x4, 0, 1, 0, 1, 1, 1 ) + +#define MPP18_GPO MPP( 18, 0x0, 0, 1, 1, 1, 1, 1 ) +#define MPP18_NF_IO0 MPP( 18, 0x1, 1, 1, 1, 1, 1, 1 ) + +#define MPP19_GPO MPP( 19, 0x0, 0, 1, 1, 1, 1, 1 ) +#define MPP19_NF_IO1 MPP( 19, 0x1, 1, 1, 1, 1, 1, 1 ) + +#define MPP20_GPIO MPP( 20, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP20_TSMP0 MPP( 20, 0x1, 1, 1, 0, 0, 1, 1 ) +#define MPP20_TDM_CH0_TX_QL MPP( 20, 0x2, 0, 1, 0, 0, 1, 1 ) +#define MPP20_GE1_0 MPP( 20, 0x3, 0, 0, 0, 1, 1, 1 ) +#define MPP20_AUDIO_SPDIFI MPP( 20, 0x4, 1, 0, 0, 0, 1, 1 ) +#define MPP20_SATA1_ACTn MPP( 20, 0x5, 0, 1, 0, 0, 1, 1 ) + +#define MPP21_GPIO MPP( 21, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP21_TSMP1 MPP( 21, 0x1, 1, 1, 0, 0, 1, 1 ) +#define MPP21_TDM_CH0_RX_QL MPP( 21, 0x2, 0, 1, 0, 0, 1, 1 ) +#define MPP21_GE1_1 MPP( 21, 0x3, 0, 0, 0, 1, 1, 1 ) +#define MPP21_AUDIO_SPDIFO MPP( 21, 0x4, 0, 1, 0, 0, 1, 1 ) +#define MPP21_SATA0_ACTn MPP( 21, 0x5, 0, 1, 0, 1, 1, 1 ) + +#define MPP22_GPIO MPP( 22, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP22_TSMP2 MPP( 22, 0x1, 1, 1, 0, 0, 1, 1 ) +#define MPP22_TDM_CH2_TX_QL MPP( 22, 0x2, 0, 1, 0, 0, 1, 1 ) +#define MPP22_GE1_2 MPP( 22, 0x3, 0, 0, 0, 1, 1, 1 ) +#define MPP22_AUDIO_SPDIFRMKCLK MPP( 22, 0x4, 0, 1, 0, 0, 1, 1 ) +#define MPP22_SATA1_PRESENTn MPP( 22, 0x5, 0, 1, 0, 0, 1, 1 ) + +#define MPP23_GPIO MPP( 23, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP23_TSMP3 MPP( 23, 0x1, 1, 1, 0, 0, 1, 1 ) +#define MPP23_TDM_CH2_RX_QL MPP( 23, 0x2, 1, 0, 0, 0, 1, 1 ) +#define MPP23_GE1_3 MPP( 23, 0x3, 0, 0, 0, 1, 1, 1 ) +#define MPP23_AUDIO_I2SBCLK MPP( 23, 0x4, 0, 1, 0, 0, 1, 1 ) +#define MPP23_SATA0_PRESENTn MPP( 23, 0x5, 0, 1, 0, 1, 1, 1 ) + +#define MPP24_GPIO MPP( 24, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP24_TSMP4 MPP( 24, 0x1, 1, 1, 0, 0, 1, 1 ) +#define MPP24_TDM_SPI_CS0 DEV( 24, 0x2, 0, 1, 0, 0, 1, 1 ) +#define MPP24_GE1_4 MPP( 24, 0x3, 0, 0, 0, 1, 1, 1 ) +#define MPP24_AUDIO_I2SDO MPP( 24, 0x4, 0, 1, 0, 0, 1, 1 ) + +#define MPP25_GPIO MPP( 25, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP25_TSMP5 MPP( 25, 0x1, 1, 1, 0, 0, 1, 1 ) +#define MPP25_TDM_SPI_SCK MPP( 25, 0x2, 0, 1, 0, 0, 1, 1 ) +#define MPP25_GE1_5 MPP( 25, 0x3, 0, 0, 0, 1, 1, 1 ) +#define MPP25_AUDIO_I2SLRCLK MPP( 25, 0x4, 0, 1, 0, 0, 1, 1 ) + +#define MPP26_GPIO MPP( 26, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP26_TSMP6 MPP( 26, 0x1, 1, 1, 0, 0, 1, 1 ) +#define MPP26_TDM_SPI_MISO MPP( 26, 0x2, 1, 0, 0, 0, 1, 1 ) +#define MPP26_GE1_6 MPP( 26, 0x3, 0, 0, 0, 1, 1, 1 ) +#define MPP26_AUDIO_I2SMCLK MPP( 26, 0x4, 0, 1, 0, 0, 1, 1 ) + +#define MPP27_GPIO MPP( 27, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP27_TSMP7 MPP( 27, 0x1, 1, 1, 0, 0, 1, 1 ) +#define MPP27_TDM_SPI_MOSI MPP( 27, 0x2, 0, 1, 0, 0, 1, 1 ) +#define MPP27_GE1_7 MPP( 27, 0x3, 0, 0, 0, 1, 1, 1 ) +#define MPP27_AUDIO_I2SDI MPP( 27, 0x4, 1, 0, 0, 0, 1, 1 ) + +#define MPP28_GPIO MPP( 28, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP28_TSMP8 MPP( 28, 0x1, 1, 1, 0, 0, 1, 1 ) +#define MPP28_TDM_CODEC_INTn MPP( 28, 0x2, 0, 0, 0, 0, 1, 1 ) +#define MPP28_GE1_8 MPP( 28, 0x3, 0, 0, 0, 1, 1, 1 ) +#define MPP28_AUDIO_EXTCLK MPP( 28, 0x4, 1, 0, 0, 0, 1, 1 ) + +#define MPP29_GPIO MPP( 29, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP29_TSMP9 MPP( 29, 0x1, 1, 1, 0, 0, 1, 1 ) +#define MPP29_TDM_CODEC_RSTn MPP( 29, 0x2, 0, 0, 0, 0, 1, 1 ) +#define MPP29_GE1_9 MPP( 29, 0x3, 0, 0, 0, 1, 1, 1 ) + +#define MPP30_GPIO MPP( 30, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP30_TSMP10 MPP( 30, 0x1, 1, 1, 0, 0, 1, 1 ) +#define MPP30_TDM_PCLK MPP( 30, 0x2, 1, 1, 0, 0, 1, 1 ) +#define MPP30_GE1_10 MPP( 30, 0x3, 0, 0, 0, 1, 1, 1 ) + +#define MPP31_GPIO MPP( 31, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP31_TSMP11 MPP( 31, 0x1, 1, 1, 0, 0, 1, 1 ) +#define MPP31_TDM_FS MPP( 31, 0x2, 1, 1, 0, 0, 1, 1 ) +#define MPP31_GE1_11 MPP( 31, 0x3, 0, 0, 0, 1, 1, 1 ) + +#define MPP32_GPIO MPP( 32, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP32_TSMP12 MPP( 32, 0x1, 1, 1, 0, 0, 1, 1 ) +#define MPP32_TDM_DRX MPP( 32, 0x2, 1, 0, 0, 0, 1, 1 ) +#define MPP32_GE1_12 MPP( 32, 0x3, 0, 0, 0, 1, 1, 1 ) + +#define MPP33_GPIO MPP( 33, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP33_TDM_DTX MPP( 33, 0x2, 0, 1, 0, 0, 1, 1 ) +#define MPP33_GE1_13 MPP( 33, 0x3, 0, 0, 0, 1, 1, 1 ) + +#define MPP34_GPIO MPP( 34, 0x0, 1, 1, 0, 1, 1, 1 ) +#define MPP34_TDM_SPI_CS1 MPP( 34, 0x2, 0, 1, 0, 0, 1, 1 ) +#define MPP34_GE1_14 MPP( 34, 0x3, 0, 0, 0, 1, 1, 1 ) + +#define MPP35_GPIO MPP( 35, 0x0, 1, 1, 1, 1, 1, 1 ) +#define MPP35_TDM_CH0_TX_QL MPP( 35, 0x2, 0, 1, 0, 0, 1, 1 ) +#define MPP35_GE1_15 MPP( 35, 0x3, 0, 0, 0, 1, 1, 1 ) +#define MPP35_SATA0_ACTn MPP( 35, 0x5, 0, 1, 0, 1, 1, 1 ) +#define MPP35_MII0_RXERR MPP( 35, 0xc, 1, 0, 1, 1, 1, 1 ) + +#define MPP36_GPIO MPP( 36, 0x0, 1, 1, 1, 0, 0, 1 ) +#define MPP36_TSMP0 MPP( 36, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP36_TDM_SPI_CS1 MPP( 36, 0x2, 0, 1, 0, 0, 0, 1 ) +#define MPP36_AUDIO_SPDIFI MPP( 36, 0x4, 1, 0, 1, 0, 0, 1 ) + +#define MPP37_GPIO MPP( 37, 0x0, 1, 1, 1, 0, 0, 1 ) +#define MPP37_TSMP1 MPP( 37, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP37_TDM_CH2_TX_QL MPP( 37, 0x2, 0, 1, 0, 0, 0, 1 ) +#define MPP37_AUDIO_SPDIFO MPP( 37, 0x4, 0, 1, 1, 0, 0, 1 ) + +#define MPP38_GPIO MPP( 38, 0x0, 1, 1, 1, 0, 0, 1 ) +#define MPP38_TSMP2 MPP( 38, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP38_TDM_CH2_RX_QL MPP( 38, 0x2, 0, 1, 0, 0, 0, 1 ) +#define MPP38_AUDIO_SPDIFRMLCLK MPP( 38, 0x4, 0, 1, 1, 0, 0, 1 ) + +#define MPP39_GPIO MPP( 39, 0x0, 1, 1, 1, 0, 0, 1 ) +#define MPP39_TSMP3 MPP( 39, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP39_TDM_SPI_CS0 MPP( 39, 0x2, 0, 1, 0, 0, 0, 1 ) +#define MPP39_AUDIO_I2SBCLK MPP( 39, 0x4, 0, 1, 1, 0, 0, 1 ) + +#define MPP40_GPIO MPP( 40, 0x0, 1, 1, 1, 0, 0, 1 ) +#define MPP40_TSMP4 MPP( 40, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP40_TDM_SPI_SCK MPP( 40, 0x2, 0, 1, 0, 0, 0, 1 ) +#define MPP40_AUDIO_I2SDO MPP( 40, 0x4, 0, 1, 1, 0, 0, 1 ) + +#define MPP41_GPIO MPP( 41, 0x0, 1, 1, 1, 0, 0, 1 ) +#define MPP41_TSMP5 MPP( 41, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP41_TDM_SPI_MISO MPP( 41, 0x2, 1, 0, 0, 0, 0, 1 ) +#define MPP41_AUDIO_I2SLRC MPP( 41, 0x4, 0, 1, 1, 0, 0, 1 ) + +#define MPP42_GPIO MPP( 42, 0x0, 1, 1, 1, 0, 0, 1 ) +#define MPP42_TSMP6 MPP( 42, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP42_TDM_SPI_MOSI MPP( 42, 0x2, 0, 1, 0, 0, 0, 1 ) +#define MPP42_AUDIO_I2SMCLK MPP( 42, 0x4, 0, 1, 1, 0, 0, 1 ) + +#define MPP43_GPIO MPP( 43, 0x0, 1, 1, 1, 0, 0, 1 ) +#define MPP43_TSMP7 MPP( 43, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP43_TDM_CODEC_INTn MPP( 43, 0x2, 0, 0, 0, 0, 0, 1 ) +#define MPP43_AUDIO_I2SDI MPP( 43, 0x4, 1, 0, 1, 0, 0, 1 ) + +#define MPP44_GPIO MPP( 44, 0x0, 1, 1, 1, 0, 0, 1 ) +#define MPP44_TSMP8 MPP( 44, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP44_TDM_CODEC_RSTn MPP( 44, 0x2, 0, 0, 0, 0, 0, 1 ) +#define MPP44_AUDIO_EXTCLK MPP( 44, 0x4, 1, 0, 1, 0, 0, 1 ) + +#define MPP45_GPIO MPP( 45, 0x0, 1, 1, 0, 0, 0, 1 ) +#define MPP45_TSMP9 MPP( 45, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP45_TDM_PCLK MPP( 45, 0x2, 1, 1, 0, 0, 0, 1 ) + +#define MPP46_GPIO MPP( 46, 0x0, 1, 1, 0, 0, 0, 1 ) +#define MPP46_TSMP10 MPP( 46, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP46_TDM_FS MPP( 46, 0x2, 1, 1, 0, 0, 0, 1 ) + +#define MPP47_GPIO MPP( 47, 0x0, 1, 1, 0, 0, 0, 1 ) +#define MPP47_TSMP11 MPP( 47, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP47_TDM_DRX MPP( 47, 0x2, 1, 0, 0, 0, 0, 1 ) + +#define MPP48_GPIO MPP( 48, 0x0, 1, 1, 0, 0, 0, 1 ) +#define MPP48_TSMP12 MPP( 48, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP48_TDM_DTX MPP( 48. 0x2, 0, 1, 0, 0, 0, 1 ) + +#define MPP49_GPIO MPP( 49, 0x0, 1, 1, 0, 0, 0, 1 ) +#define MPP49_TSMP9 MPP( 49, 0x1, 1, 1, 0, 0, 0, 1 ) +#define MPP49_TDM_CH0_RX_QL MPP( 49, 0x2, 0, 1, 0, 0, 0, 1 ) +#define MPP49_PTP_CLK MPP( 49, 0x5, 1, 0, 0, 0, 0, 1 ) + +#define MPP_MAX 49 + +void kirkwood_mpp_conf(unsigned int *mpp_list); + +#endif diff --git a/include/asm-arm/arch-kirkwood/spi.h b/include/asm-arm/arch-kirkwood/spi.h new file mode 100644 index 0000000..8719279 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/spi.h @@ -0,0 +1,56 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar <prafulla(a)marvell.com> + * + * Derived from drivers/spi/mpc8xxx_spi.c + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef __KW_SPI_H__ +#define __KW_SPI_H__ + +/* SPI Registers on kirkwood SOC */ +struct kwspi_registers { + u32 ctrl; /* 0x10600 */ + u32 cfg; /* 0x10604 */ + u32 dout; /* 0x10608 */ + u32 din; /* 0x1060c */ + u32 irq_cause; /* 0x10610 */ + u32 irq_mask; /* 0x10614 */ +}; + +#define KWSPI_CLKPRESCL_MASK 0x1f +#define KWSPI_CSN_ACT 1 /* Activates serial memory interface */ +#define KWSPI_SMEMRDY (1 << 1) /* SerMem Data xfer ready */ +#define KWSPI_IRQUNMASK 1 /* unmask SPI interrupt */ +#define KWSPI_IRQMASK 0 /* mask SPI interrupt */ +#define KWSPI_SMEMRDIRQ 1 /* SerMem data xfer ready irq */ +#define KWSPI_XFERLEN_1BYTE 0 +#define KWSPI_XFERLEN_2BYTE (1 << 5) +#define KWSPI_XFERLEN_MASK (1 << 5) +#define KWSPI_ADRLEN_1BYTE 0 +#define KWSPI_ADRLEN_2BYTE 1 << 8 +#define KWSPI_ADRLEN_3BYTE 2 << 8 +#define KWSPI_ADRLEN_4BYTE 3 << 8 +#define KWSPI_ADRLEN_MASK 3 << 8 +#define KWSPI_TIMEOUT 10000 + +#endif /* __KW_SPI_H__ */ diff --git a/include/asm-arm/cache.h b/include/asm-arm/cache.h new file mode 100644 index 0000000..205b5da --- /dev/null +++ b/include/asm-arm/cache.h @@ -0,0 +1,41 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar <prafulla(a)marvell.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef _ASM_CACHE_H +#define _ASM_CACHE_H + +#include <asm/system.h> + +/* + * Invalidate L2 Cache using co-proc instruction + */ +static inline void invalidate_l2_cache(void) +{ + unsigned int val=0; + + asm volatile("mcr p15, 1, %0, c15, c11, 0 @ invl l2 cache" + : : "r" (val) : "cc"); + isb(); +} +#endif /* _ASM_CACHE_H */ diff --git a/include/common.h b/include/common.h index 30fff7d..9e4b859 100644 --- a/include/common.h +++ b/include/common.h @@ -294,6 +294,7 @@ void pciinfo (int, int); #endif #endif +int arch_misc_init (void); int misc_init_f (void); int misc_init_r (void); diff --git a/lib_arm/board.c b/lib_arm/board.c index e081fbc..5c3bfec 100644 --- a/lib_arm/board.c +++ b/lib_arm/board.c @@ -399,6 +399,10 @@ void start_armboot (void) console_init_r (); /* fully init console as a device */ +#if defined(CONFIG_ARCH_MISC_INIT) + /* miscellaneous arch dependent initialisations */ + arch_misc_init (); +#endif #if defined(CONFIG_MISC_INIT_R) /* miscellaneous platform dependent initialisations */ misc_init_r (); -- 1.5.3.3

9 82

[U-Boot] Please pull u-boot-i2c.git
by Heiko Schocher 23 Jul '09

23 Jul '09

Hello Wolfgang, The following changes since commit 1bc1538613d66cef3cbce680fc8d7c3561a0fbd0: Peter Tyser (1): Move examples/ to examples/standalone are available in the git repository at: git://git.denx.de/u-boot-i2c.git master Heiko Schocher (1): i2c, mpc83xx: add CONFIG_SYS_I2C_INIT_BOARD for fsl_i2c board/keymile/common/common.c | 20 ++++++++++++++++++++ drivers/i2c/fsl_i2c.c | 6 ++++++ include/configs/kmeter1.h | 1 - 3 files changed, 26 insertions(+), 1 deletions(-) -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

2 1