April 2024 - U-Boot

[PATCH] spi: dw: Use controller clock rate as maximum frequency
by Kunihiko Hayashi 05 Apr '24

05 Apr '24

Currently the controller driver has maximum frequency in plat->frequency that is specified by "spi-max-frequency" DT property in the controller node. This is special to U-Boot and doesn't exist to Linux. spi { spi-max-frequency = <A>; }; Usually the frequency should be specified by "spi-max-frequency" at the slave device node. spi { slave { spi-max-frequency = <B>; }; }; The final maximum frequency is set to the smaller value of the controller node (A) and the slave device node (B). Currently, if the property in the controller node is omitted, the default frequency is fixed at 500kHz. Even if the controller and the slave device allow the higher frequency than 500kHz, the maximum frequency can't exceed 500kHz. The upper limit of the maximum frequency should be determined by the clock rate of the controller clock. And this patch determines the maximum frequency based on the clock rate if the controller node property isn't specified. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko(a)socionext.com> --- drivers/spi/designware_spi.c | 13 ++++++++----- 1 file changed, 8 insertions(+), 5 deletions(-) diff --git a/drivers/spi/designware_spi.c b/drivers/spi/designware_spi.c index 1c7d0ca310b6..637ea57eba24 100644 --- a/drivers/spi/designware_spi.c +++ b/drivers/spi/designware_spi.c @@ -250,15 +250,13 @@ static int dw_spi_of_to_plat(struct udevice *bus) if (!plat->regs) return -EINVAL; - /* Use 500KHz as a suitable default */ + /* Specify fixed max-frequency as default */ plat->frequency = dev_read_u32_default(bus, "spi-max-frequency", - 500000); + 0); if (dev_read_bool(bus, "spi-slave")) return -EINVAL; - dev_info(bus, "max-frequency=%d\n", plat->frequency); - return request_gpio_cs(bus); } @@ -362,12 +360,17 @@ static int dw_spi_probe(struct udevice *bus) u32 version; priv->regs = plat->regs; - priv->freq = plat->frequency; ret = dw_spi_get_clk(bus, &priv->bus_clk_rate); if (ret) return ret; + if (!plat->frequency) + plat->frequency = priv->bus_clk_rate; + + dev_info(bus, "max-frequency=%d\n", plat->frequency); + priv->freq = plat->frequency; + ret = dw_spi_reset(bus); if (ret) return ret; -- 2.25.1

2 2

[PULL] Please pull qcom-next-2024Apr04
by Caleb Connolly 04 Apr '24

04 Apr '24

Hi Tom, Some new Qualcomm features for you: * Ethernet, i2c, and USB support are now enabled by default * The clock driver gets some bug fixes and cleanup * Invalid FDTs are now properly detected in board_fdt_blob_setup(). * The pinctrl driver gains preparatory support for per-pin function muxes. * Support is added for two generations of Qualcomm HighSpeed USB PHY * A power domain driver is added for the Globall Distributed Switch Controllers on the GCC hardware block. * SDM845 gains USB host mode support. * OF_LIVE is enabled by default for Qualcomm platforms * Some U-Boot devicetree compatibility fixups are added during init to improve compatbility with upstream DT. The following changes since commit b2511143fba4c0631446c968fb4c0d962b01d850: qcom_defconfig: enable USB (2024-04-04 17:46:48 +0200) are available in the Git repository at: git@source.denx.de:u-boot/custodians/u-boot-snapdragon.git tags/qcom-next-2024Apr04 for you to fetch changes up to b2511143fba4c0631446c968fb4c0d962b01d850: qcom_defconfig: enable USB (2024-04-04 17:46:48 +0200) ----------------------------------------------------------------

1 0

[PATCH v2 0/4] boot: fix EFI boot methods
by Heinrich Schuchardt 04 Apr '24

04 Apr '24

The default sequence of boot methods is determined by alphabetical sorting during linkage. * efi_mgr must run before efi to be UEFI compliant * pxe should run as last resort If UEFI is enabled in U-Boot, we want it to conform to the UEFI specification. This requires enabling the boot manager boot method. The sandbox must not use an arbitrary file name bootsbox.efi but the file name matching the host architecture to properly boot the respective file. We already have an include which provides a macro with the name of the EFI binary. Use it. The path to the EFI binary should be absolute. The path and the file name must be capitalized to conform to the UEFI specification. This is important when reading from case sensitive file systems. v2: fix building with EFI_BOOT_MGR but w/o BOOTSTD correct finding the default EFI binary Heinrich Schuchardt (4): boot: correct the default sequence of boot methods boot: enable booting via EFI boot manager by default efi_loader: move HOST_ARCH to version_autogenerated.h boot: correct finding the default EFI binary Makefile | 1 + arch/sandbox/config.mk | 2 -- boot/Kconfig | 10 +++++++++ boot/Makefile | 2 +- boot/bootmeth_efi.c | 46 ++++------------------------------------- boot/bootmeth_efi_mgr.c | 2 +- boot/bootmeth_pxe.c | 2 +- include/host_arch.h | 2 ++ lib/efi_loader/Kconfig | 1 - lib/efi_loader/Makefile | 3 +-- test/boot/bootflow.c | 6 ++++-- 11 files changed, 25 insertions(+), 52 deletions(-) -- 2.43.0

3 11

[PATCH v5 0/5] TEE: minor cleanup
by Igor Opaniuk 04 Apr '24

04 Apr '24

- Address some spelling errors and typos - Support CMD_OPTEE_RPMB for SANDBOX configurations and add python tests - Remove common.h inclusion for drivers/tee - Add calls for closing tee session after every read/write operation. CI build: [1] https://dev.azure.com/igoropaniuk/u-boot/_build/results?buildId=33&view=res… Changes in v5: - Extended commit message for "cmd: optee_rpmb: close tee session" - Added R-b tag Changes in v4: - Rebased on the latest master and excluded "tee: sandbox: fix spelling errors", as it was merged already by Heinrich Schuchardt Changes in v3: - Added calls for closing tee session after every read/write operation Changes in v2: - Fixed chimp_optee.c:37:9: error: implicit declaration of function 'memset' - Applied R-b and T-b tags Igor Opaniuk (5): tee: optee: fix description in Kconfig cmd: optee_rpmb: close tee session cmd: optee_rpmb: build cmd for sandbox test: py: add optee_rpmb tests tee: remove common.h inclusion cmd/Kconfig | 4 +++- cmd/optee_rpmb.c | 23 +++++++++++++++++------ drivers/tee/broadcom/chimp_optee.c | 3 ++- drivers/tee/optee/Kconfig | 2 +- drivers/tee/optee/core.c | 1 - drivers/tee/optee/i2c.c | 1 - drivers/tee/optee/rpmb.c | 1 - drivers/tee/optee/supplicant.c | 2 +- drivers/tee/sandbox.c | 2 +- drivers/tee/tee-uclass.c | 1 - test/py/tests/test_optee_rpmb.py | 20 ++++++++++++++++++++ 11 files changed, 45 insertions(+), 15 deletions(-) create mode 100644 test/py/tests/test_optee_rpmb.py -- 2.34.1

1 5

[PATCH v3] arm: dts: kirkwood: Enable upstream DT on Kirkwood boards
by Tony Dinh 04 Apr '24

04 Apr '24

Enable OF_UPSTREAM to use upstream DT and add marvell/ prefix to the DEFAULT_DEVICE_TREE for Kirkwood boards. And so we can directly build DTBs from dts/upstream/src/arm/marvell, and including *-u-boot.dtsi files from arch/arm/dts/ directory. Background: The following 2 commands and filters were used in the analysis to determine which upstream DTS and DTSI files can be used as they are, or need to have modified/created *-u-boot.dtsi for u-boot specific implementation, and which board should be opt-out from OF_UPSTREAM. "git grep -li arch_kirkwood configs | xargs grep DEVICE_TREE | cut -d '"' -f2 | xargs -n1 sh -c 'diff -qs arch/arm/dts/$1.dts dts/upstream/src/arm/marvell/$1.dts' sh | grep differ" "diff -qrbu arch/arm/dts/ dts/upstream/src/arm/marvell/ | grep kirkwood | grep ".dtsi "" More detailed information can be found at: https://lore.kernel.org/u-boot/20240328021825.17935-1-mibodhi@gmail.com/T/#u I've regression tested this patch with the Zyxel NSA325 (Kirkwood 88F6282) and Zyxel NSA310S (Kirkwood 88F6281). The Zyxel NSA325 board has a USB 3.0 controller attached to the PCIe bus. And the Zyxel NSA310S has an extensive overhaul in bindings and styles in upstream DTS version. Tested-by: Michael Walle <michael(a)walle.cc> # on lschv2 Acked-by: Sumit Garg <sumit.garg(a)linaro.org> Reviewed-by: Stefan Roese <sr(a)denx.de> Signed-off-by: Tony Dinh <mibodhi(a)gmail.com> --- Changes in v3: - Collect Reviewed/Tested/Acked-by tags. - Trim the commit description and point to lore.kernel.org for detailed information. - No change from the V2 patch. Changes in v2: Remove unnecessary redefined OF_UPSTREAM and use "imply OF_UPSTREAM" for KW88F6281 and KW88F6192 SoCs. arch/arm/dts/kirkwood-dreamplug-u-boot.dtsi | 7 +++++++ arch/arm/dts/kirkwood-lschlv2-u-boot.dtsi | 6 ++++-- arch/arm/dts/kirkwood-lsxhl-u-boot.dtsi | 6 ++++-- arch/arm/dts/kirkwood-nsa325-u-boot.dtsi | 7 +++++++ arch/arm/mach-kirkwood/Kconfig | 2 ++ configs/SBx81LIFKW_defconfig | 1 + configs/SBx81LIFXCAT_defconfig | 1 + configs/d2net_v2_defconfig | 2 +- configs/dns325_defconfig | 2 +- configs/dockstar_defconfig | 2 +- configs/dreamplug_defconfig | 2 +- configs/ds109_defconfig | 2 +- configs/goflexhome_defconfig | 2 +- configs/guruplug_defconfig | 2 +- configs/ib62x0_defconfig | 2 +- configs/iconnect_defconfig | 2 +- configs/inetspace_v2_defconfig | 2 +- configs/lschlv2_defconfig | 2 +- configs/lsxhl_defconfig | 2 +- configs/nas220_defconfig | 2 +- configs/net2big_v2_defconfig | 2 +- configs/netspace_lite_v2_defconfig | 2 +- configs/netspace_max_v2_defconfig | 2 +- configs/netspace_mini_v2_defconfig | 2 +- configs/netspace_v2_defconfig | 2 +- configs/nsa310s_defconfig | 2 +- configs/nsa325_defconfig | 2 +- configs/openrd_base_defconfig | 2 +- configs/openrd_client_defconfig | 2 +- configs/openrd_ultimate_defconfig | 2 +- configs/pogo_e02_defconfig | 2 +- configs/pogo_v4_defconfig | 2 +- configs/sheevaplug_defconfig | 2 +- 33 files changed, 52 insertions(+), 30 deletions(-) create mode 100644 arch/arm/dts/kirkwood-dreamplug-u-boot.dtsi create mode 100644 arch/arm/dts/kirkwood-nsa325-u-boot.dtsi diff --git a/arch/arm/dts/kirkwood-dreamplug-u-boot.dtsi b/arch/arm/dts/kirkwood-dreamplug-u-boot.dtsi new file mode 100644 index 0000000000..59f19a211f --- /dev/null +++ b/arch/arm/dts/kirkwood-dreamplug-u-boot.dtsi @@ -0,0 +1,7 @@ +// SPDX-License-Identifier: GPL-2.0+ + +/ { + aliases { + spi0 = &spi0; + }; +}; diff --git a/arch/arm/dts/kirkwood-lschlv2-u-boot.dtsi b/arch/arm/dts/kirkwood-lschlv2-u-boot.dtsi index 7fc2d7d3b4..cf33ff822e 100644 --- a/arch/arm/dts/kirkwood-lschlv2-u-boot.dtsi +++ b/arch/arm/dts/kirkwood-lschlv2-u-boot.dtsi @@ -1,7 +1,9 @@ // SPDX-License-Identifier: GPL-2.0+ -&eth0 { - status = "disabled"; +/ { + aliases { + spi0 = &spi0; + }; }; &hdd_power { diff --git a/arch/arm/dts/kirkwood-lsxhl-u-boot.dtsi b/arch/arm/dts/kirkwood-lsxhl-u-boot.dtsi index 7fc2d7d3b4..cf33ff822e 100644 --- a/arch/arm/dts/kirkwood-lsxhl-u-boot.dtsi +++ b/arch/arm/dts/kirkwood-lsxhl-u-boot.dtsi @@ -1,7 +1,9 @@ // SPDX-License-Identifier: GPL-2.0+ -&eth0 { - status = "disabled"; +/ { + aliases { + spi0 = &spi0; + }; }; &hdd_power { diff --git a/arch/arm/dts/kirkwood-nsa325-u-boot.dtsi b/arch/arm/dts/kirkwood-nsa325-u-boot.dtsi new file mode 100644 index 0000000000..dec27b2a87 --- /dev/null +++ b/arch/arm/dts/kirkwood-nsa325-u-boot.dtsi @@ -0,0 +1,7 @@ +// SPDX-License-Identifier: GPL-2.0+ + +&nand { + partition@0 { + /delete-property/ read-only; + }; +}; diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig index c2fff84a68..031d4e5ecd 100644 --- a/arch/arm/mach-kirkwood/Kconfig +++ b/arch/arm/mach-kirkwood/Kconfig @@ -6,10 +6,12 @@ config FEROCEON_88FR131 config KW88F6192 bool select ARCH_VERY_EARLY_INIT + imply OF_UPSTREAM config KW88F6281 bool select ARCH_VERY_EARLY_INIT + imply OF_UPSTREAM config SHEEVA_88SV131 bool diff --git a/configs/SBx81LIFKW_defconfig b/configs/SBx81LIFKW_defconfig index cc17a8b114..977daf9f09 100644 --- a/configs/SBx81LIFKW_defconfig +++ b/configs/SBx81LIFKW_defconfig @@ -6,6 +6,7 @@ CONFIG_ARCH_KIRKWOOD=y CONFIG_SYS_KWD_CONFIG="board/alliedtelesis/SBx81LIFKW/kwbimage.cfg" CONFIG_TEXT_BASE=0x00600000 CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 +# CONFIG_OF_UPSTREAM is not set CONFIG_TARGET_SBx81LIFKW=y CONFIG_ENV_SIZE=0x2000 CONFIG_ENV_OFFSET=0xC0000 diff --git a/configs/SBx81LIFXCAT_defconfig b/configs/SBx81LIFXCAT_defconfig index 0612723298..9bc8614030 100644 --- a/configs/SBx81LIFXCAT_defconfig +++ b/configs/SBx81LIFXCAT_defconfig @@ -6,6 +6,7 @@ CONFIG_ARCH_KIRKWOOD=y CONFIG_SYS_KWD_CONFIG="board/alliedtelesis/SBx81LIFXCAT/kwbimage.cfg" CONFIG_TEXT_BASE=0x00600000 CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 +# CONFIG_OF_UPSTREAM is not set CONFIG_TARGET_SBx81LIFXCAT=y CONFIG_ENV_SIZE=0x2000 CONFIG_ENV_OFFSET=0xC0000 diff --git a/configs/d2net_v2_defconfig b/configs/d2net_v2_defconfig index bb1bcb0aa3..69658a2ba7 100644 --- a/configs/d2net_v2_defconfig +++ b/configs/d2net_v2_defconfig @@ -11,7 +11,7 @@ CONFIG_TARGET_NET2BIG_V2=y CONFIG_ENV_SIZE=0x1000 CONFIG_ENV_OFFSET=0x70000 CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-d2net" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-d2net" CONFIG_IDENT_STRING=" D2 v2" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 diff --git a/configs/dns325_defconfig b/configs/dns325_defconfig index edfe92c5f3..b85f7cac8e 100644 --- a/configs/dns325_defconfig +++ b/configs/dns325_defconfig @@ -10,7 +10,7 @@ CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_TARGET_DNS325=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0xE0000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-dns325" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-dns325" CONFIG_IDENT_STRING="\nD-Link DNS-325" CONFIG_SYS_LOAD_ADDR=0x800000 # CONFIG_SYS_MALLOC_F is not set diff --git a/configs/dockstar_defconfig b/configs/dockstar_defconfig index 719fa3979e..7b5f19433a 100644 --- a/configs/dockstar_defconfig +++ b/configs/dockstar_defconfig @@ -13,7 +13,7 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_TARGET_DOCKSTAR=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0x80000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-dockstar" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-dockstar" CONFIG_IDENT_STRING="\nSeagate FreeAgent DockStar" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_BOOTDELAY=3 diff --git a/configs/dreamplug_defconfig b/configs/dreamplug_defconfig index 02a2635af8..8518eabcb2 100644 --- a/configs/dreamplug_defconfig +++ b/configs/dreamplug_defconfig @@ -13,7 +13,7 @@ CONFIG_TARGET_DREAMPLUG=y CONFIG_ENV_SIZE=0x1000 CONFIG_ENV_OFFSET=0x100000 CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-dreamplug" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-dreamplug" CONFIG_IDENT_STRING="\nMarvell-DreamPlug" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x100000 diff --git a/configs/ds109_defconfig b/configs/ds109_defconfig index 304c098c99..ef805eca56 100644 --- a/configs/ds109_defconfig +++ b/configs/ds109_defconfig @@ -14,7 +14,7 @@ CONFIG_TARGET_DS109=y CONFIG_ENV_SIZE=0x10000 CONFIG_ENV_OFFSET=0x3D0000 CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ds109" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-ds109" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x3D0000 # CONFIG_SYS_MALLOC_F is not set diff --git a/configs/goflexhome_defconfig b/configs/goflexhome_defconfig index d577d5807b..53b2ce97e8 100644 --- a/configs/goflexhome_defconfig +++ b/configs/goflexhome_defconfig @@ -13,7 +13,7 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_TARGET_GOFLEXHOME=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0xC0000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-goflexnet" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-goflexnet" CONFIG_IDENT_STRING="\nSeagate GoFlex Home" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_BOOTDELAY=3 diff --git a/configs/guruplug_defconfig b/configs/guruplug_defconfig index 7cb649e29c..5371ee403b 100644 --- a/configs/guruplug_defconfig +++ b/configs/guruplug_defconfig @@ -10,7 +10,7 @@ CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_TARGET_GURUPLUG=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0xE0000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-guruplug-server-plus" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-guruplug-server-plus" CONFIG_IDENT_STRING="\nMarvell-GuruPlug" CONFIG_SYS_LOAD_ADDR=0x800000 # CONFIG_SYS_MALLOC_F is not set diff --git a/configs/ib62x0_defconfig b/configs/ib62x0_defconfig index 074384e387..32b0e1c395 100644 --- a/configs/ib62x0_defconfig +++ b/configs/ib62x0_defconfig @@ -10,7 +10,7 @@ CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_TARGET_IB62X0=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0xE0000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ib62x0" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-ib62x0" CONFIG_IDENT_STRING=" RaidSonic ICY BOX IB-NAS62x0" CONFIG_SYS_LOAD_ADDR=0x800000 # CONFIG_SYS_MALLOC_F is not set diff --git a/configs/iconnect_defconfig b/configs/iconnect_defconfig index f7b74c4662..45ffbd92db 100644 --- a/configs/iconnect_defconfig +++ b/configs/iconnect_defconfig @@ -13,7 +13,7 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_TARGET_ICONNECT=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0x80000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-iconnect" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-iconnect" CONFIG_IDENT_STRING=" Iomega iConnect" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_PCI=y diff --git a/configs/inetspace_v2_defconfig b/configs/inetspace_v2_defconfig index 2e8e3f3928..3fa7790d77 100644 --- a/configs/inetspace_v2_defconfig +++ b/configs/inetspace_v2_defconfig @@ -11,7 +11,7 @@ CONFIG_TARGET_NETSPACE_V2=y CONFIG_ENV_SIZE=0x1000 CONFIG_ENV_OFFSET=0x70000 CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-is2" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-is2" CONFIG_IDENT_STRING=" IS v2" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 diff --git a/configs/lschlv2_defconfig b/configs/lschlv2_defconfig index 99bdbc1483..ad060079a7 100644 --- a/configs/lschlv2_defconfig +++ b/configs/lschlv2_defconfig @@ -15,7 +15,7 @@ CONFIG_ENV_SIZE=0x10000 CONFIG_ENV_OFFSET=0x70000 CONFIG_ENV_SECT_SIZE=0x10000 CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-lschlv2" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-lschlv2" CONFIG_IDENT_STRING=" LS-CHLv2" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_HAS_BOARD_SIZE_LIMIT=y diff --git a/configs/lsxhl_defconfig b/configs/lsxhl_defconfig index bb0a5ddf50..b2d9f0c9d8 100644 --- a/configs/lsxhl_defconfig +++ b/configs/lsxhl_defconfig @@ -16,7 +16,7 @@ CONFIG_ENV_SIZE=0x10000 CONFIG_ENV_OFFSET=0x70000 CONFIG_ENV_SECT_SIZE=0x10000 CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-lsxhl" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-lsxhl" CONFIG_IDENT_STRING=" LS-XHL" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_HAS_BOARD_SIZE_LIMIT=y diff --git a/configs/nas220_defconfig b/configs/nas220_defconfig index f01b26f2df..4ea342a043 100644 --- a/configs/nas220_defconfig +++ b/configs/nas220_defconfig @@ -10,7 +10,7 @@ CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_TARGET_NAS220=y CONFIG_ENV_SIZE=0x10000 CONFIG_ENV_OFFSET=0xA0000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-blackarmor-nas220" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-blackarmor-nas220" CONFIG_IDENT_STRING="\nNAS 220" CONFIG_SYS_LOAD_ADDR=0x800000 # CONFIG_SYS_MALLOC_F is not set diff --git a/configs/net2big_v2_defconfig b/configs/net2big_v2_defconfig index dda627aac6..39cbc3384f 100644 --- a/configs/net2big_v2_defconfig +++ b/configs/net2big_v2_defconfig @@ -12,7 +12,7 @@ CONFIG_NET2BIG_V2=y CONFIG_ENV_SIZE=0x1000 CONFIG_ENV_OFFSET=0x70000 CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-net2big" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-net2big" CONFIG_IDENT_STRING=" 2Big v2" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 diff --git a/configs/netspace_lite_v2_defconfig b/configs/netspace_lite_v2_defconfig index 742e6205d8..cd416cb150 100644 --- a/configs/netspace_lite_v2_defconfig +++ b/configs/netspace_lite_v2_defconfig @@ -12,7 +12,7 @@ CONFIG_NETSPACE_LITE_V2=y CONFIG_ENV_SIZE=0x1000 CONFIG_ENV_OFFSET=0x70000 CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2lite" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-ns2lite" CONFIG_IDENT_STRING=" NS v2 Lite" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 diff --git a/configs/netspace_max_v2_defconfig b/configs/netspace_max_v2_defconfig index 7779e6815e..6a3d9296ac 100644 --- a/configs/netspace_max_v2_defconfig +++ b/configs/netspace_max_v2_defconfig @@ -12,7 +12,7 @@ CONFIG_NETSPACE_MAX_V2=y CONFIG_ENV_SIZE=0x1000 CONFIG_ENV_OFFSET=0x70000 CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2max" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-ns2max" CONFIG_IDENT_STRING=" NS Max v2" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 diff --git a/configs/netspace_mini_v2_defconfig b/configs/netspace_mini_v2_defconfig index 9e3614bb44..e25631b09f 100644 --- a/configs/netspace_mini_v2_defconfig +++ b/configs/netspace_mini_v2_defconfig @@ -12,7 +12,7 @@ CONFIG_NETSPACE_MINI_V2=y CONFIG_ENV_SIZE=0x1000 CONFIG_ENV_OFFSET=0x70000 CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2mini" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-ns2mini" CONFIG_IDENT_STRING=" NS v2 Mini" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 diff --git a/configs/netspace_v2_defconfig b/configs/netspace_v2_defconfig index 1583a0adb3..b6ac2a8b19 100644 --- a/configs/netspace_v2_defconfig +++ b/configs/netspace_v2_defconfig @@ -12,7 +12,7 @@ CONFIG_NETSPACE_V2=y CONFIG_ENV_SIZE=0x1000 CONFIG_ENV_OFFSET=0x70000 CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-ns2" CONFIG_IDENT_STRING=" NS v2" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_ENV_ADDR=0x70000 diff --git a/configs/nsa310s_defconfig b/configs/nsa310s_defconfig index 89d8b18b16..e859a43ffa 100644 --- a/configs/nsa310s_defconfig +++ b/configs/nsa310s_defconfig @@ -13,7 +13,7 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_TARGET_NSA310S=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0xE0000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-nsa310s" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-nsa310s" CONFIG_DEBUG_UART_BASE=0xf1012000 CONFIG_DEBUG_UART_CLOCK=166666667 CONFIG_IDENT_STRING="\nZyXEL NSA310S/320S 1/2-Bay Power Media Server" diff --git a/configs/nsa325_defconfig b/configs/nsa325_defconfig index 5da4a002b4..88a890002e 100644 --- a/configs/nsa325_defconfig +++ b/configs/nsa325_defconfig @@ -13,7 +13,7 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_TARGET_NSA325=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0xC0000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-nsa325" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-nsa325" CONFIG_IDENT_STRING="\nZyXEL NSA325 2-Bay Power Media Server" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_PCI=y diff --git a/configs/openrd_base_defconfig b/configs/openrd_base_defconfig index 29a14e0927..057dd28dff 100644 --- a/configs/openrd_base_defconfig +++ b/configs/openrd_base_defconfig @@ -11,7 +11,7 @@ CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_TARGET_OPENRD=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0x80000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-openrd-base" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-openrd-base" CONFIG_IDENT_STRING="\nOpenRD-Base" CONFIG_SYS_LOAD_ADDR=0x800000 # CONFIG_SYS_MALLOC_F is not set diff --git a/configs/openrd_client_defconfig b/configs/openrd_client_defconfig index a95a435bdf..05e4292764 100644 --- a/configs/openrd_client_defconfig +++ b/configs/openrd_client_defconfig @@ -12,7 +12,7 @@ CONFIG_TARGET_OPENRD=y CONFIG_BOARD_IS_OPENRD_CLIENT=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0x80000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-openrd-client" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-openrd-client" CONFIG_IDENT_STRING="\nOpenRD-Client" CONFIG_SYS_LOAD_ADDR=0x800000 # CONFIG_SYS_MALLOC_F is not set diff --git a/configs/openrd_ultimate_defconfig b/configs/openrd_ultimate_defconfig index e3f5294ff1..6e13c6eabd 100644 --- a/configs/openrd_ultimate_defconfig +++ b/configs/openrd_ultimate_defconfig @@ -12,7 +12,7 @@ CONFIG_TARGET_OPENRD=y CONFIG_BOARD_IS_OPENRD_ULTIMATE=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0x80000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-openrd-ultimate" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-openrd-ultimate" CONFIG_IDENT_STRING="\nOpenRD-Ultimate" CONFIG_SYS_LOAD_ADDR=0x800000 # CONFIG_SYS_MALLOC_F is not set diff --git a/configs/pogo_e02_defconfig b/configs/pogo_e02_defconfig index e53ccf34c7..880cb20b22 100644 --- a/configs/pogo_e02_defconfig +++ b/configs/pogo_e02_defconfig @@ -13,7 +13,7 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_TARGET_POGO_E02=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0xC0000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-pogo_e02" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-pogo_e02" CONFIG_IDENT_STRING="\nPogo E02" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_BOOTDELAY=3 diff --git a/configs/pogo_v4_defconfig b/configs/pogo_v4_defconfig index 95e22b3fef..50046e83b7 100644 --- a/configs/pogo_v4_defconfig +++ b/configs/pogo_v4_defconfig @@ -12,7 +12,7 @@ CONFIG_TEXT_BASE=0x600000 CONFIG_TARGET_POGO_V4=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0xC0000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-pogoplug-series-4" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-pogoplug-series-4" CONFIG_IDENT_STRING="\nPogoplug V4" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_PCI=y diff --git a/configs/sheevaplug_defconfig b/configs/sheevaplug_defconfig index 0af87dc4fb..b673b3f6da 100644 --- a/configs/sheevaplug_defconfig +++ b/configs/sheevaplug_defconfig @@ -13,7 +13,7 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_TARGET_SHEEVAPLUG=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0x80000 -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-sheevaplug" +CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-sheevaplug" CONFIG_IDENT_STRING="\nMarvell-Sheevaplug" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_HAS_BOARD_SIZE_LIMIT=y -- 2.39.2

2 1

[PATCH] arm: imx: fix signature_block_hdr struct fields order
by Javier Viguera 04 Apr '24

04 Apr '24

According to the documentation (for example AN13994), for AHAB-enabled devices the format of the signature block is: +--------------+--------------+--------------+-------------+ | Tag | Length - msb | Length - lsb | Version | +--------------+--------------+--------------+-------------+ | SRK Table offset | Certificate offset | +-----------------------------+----------------------------+ | Blob offset | Signature offset | +-----------------------------+----------------------------+ Signed-off-by: Javier Viguera <javier.viguera(a)digi.com> --- include/imx_container.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/include/imx_container.h b/include/imx_container.h index 54cd684e35d5..691c764b3e5b 100644 --- a/include/imx_container.h +++ b/include/imx_container.h @@ -50,10 +50,10 @@ struct signature_block_hdr { u8 length_lsb; u8 length_msb; u8 tag; - u16 srk_table_offset; u16 cert_offset; - u16 blob_offset; + u16 srk_table_offset; u16 signature_offset; + u16 blob_offset; u32 reserved; } __packed;

4 4

[PATCH] arm: dts: kirkwood: Remove DTS files for Kirkwood boards
by Tony Dinh 04 Apr '24

04 Apr '24

Remove DTS and DTSI files for Kirkwood boards that have upstream supports. This patch depends on "arm: dts: kirkwood: Enable upstream DT on Kirkwood boards" https://patchwork.ozlabs.org/project/uboot/patch/20240322021747.14873-1-mib… Signed-off-by: Tony Dinh <mibodhi(a)gmail.com> --- arch/arm/dts/Makefile | 28 +- arch/arm/dts/kirkwood-6192.dtsi | 88 -- arch/arm/dts/kirkwood-6281.dtsi | 90 -- arch/arm/dts/kirkwood-6282.dtsi | 161 ---- arch/arm/dts/kirkwood-98dx4122.dtsi | 53 -- arch/arm/dts/kirkwood-blackarmor-nas220.dts | 172 ---- arch/arm/dts/kirkwood-d2net.dts | 45 - arch/arm/dts/kirkwood-dns325.dts | 63 -- arch/arm/dts/kirkwood-dnskw.dtsi | 235 ----- arch/arm/dts/kirkwood-dockstar.dts | 110 --- arch/arm/dts/kirkwood-dreamplug.dts | 131 --- arch/arm/dts/kirkwood-ds109.dts | 40 - arch/arm/dts/kirkwood-goflexnet.dts | 190 ---- .../arm/dts/kirkwood-guruplug-server-plus.dts | 133 --- arch/arm/dts/kirkwood-ib62x0.dts | 146 --- arch/arm/dts/kirkwood-iconnect.dts | 195 ---- arch/arm/dts/kirkwood-is2.dts | 40 - arch/arm/dts/kirkwood-lschlv2.dts | 20 - arch/arm/dts/kirkwood-lsxhl.dts | 20 - arch/arm/dts/kirkwood-lsxl.dtsi | 241 ----- arch/arm/dts/kirkwood-net2big.dts | 63 -- arch/arm/dts/kirkwood-netxbig.dtsi | 232 ----- arch/arm/dts/kirkwood-ns2-common.dtsi | 97 -- arch/arm/dts/kirkwood-ns2.dts | 40 - arch/arm/dts/kirkwood-ns2lite.dts | 35 - arch/arm/dts/kirkwood-ns2max.dts | 59 -- arch/arm/dts/kirkwood-ns2mini.dts | 60 -- arch/arm/dts/kirkwood-nsa310s.dts | 319 ------- arch/arm/dts/kirkwood-nsa325.dts | 231 ----- arch/arm/dts/kirkwood-nsa3x0-common.dtsi | 157 ---- arch/arm/dts/kirkwood-openrd-base.dts | 39 - arch/arm/dts/kirkwood-openrd-client.dts | 73 -- arch/arm/dts/kirkwood-openrd-ultimate.dts | 55 -- arch/arm/dts/kirkwood-openrd.dtsi | 122 --- arch/arm/dts/kirkwood-pogo_e02.dts | 132 --- arch/arm/dts/kirkwood-pogoplug-series-4.dts | 180 ---- arch/arm/dts/kirkwood-sheevaplug-common.dtsi | 104 --- arch/arm/dts/kirkwood-sheevaplug.dts | 42 - arch/arm/dts/kirkwood-synology.dtsi | 855 ------------------ arch/arm/dts/kirkwood.dtsi | 393 -------- 40 files changed, 1 insertion(+), 5488 deletions(-) delete mode 100644 arch/arm/dts/kirkwood-6192.dtsi delete mode 100644 arch/arm/dts/kirkwood-6281.dtsi delete mode 100644 arch/arm/dts/kirkwood-6282.dtsi delete mode 100644 arch/arm/dts/kirkwood-98dx4122.dtsi delete mode 100644 arch/arm/dts/kirkwood-blackarmor-nas220.dts delete mode 100644 arch/arm/dts/kirkwood-d2net.dts delete mode 100644 arch/arm/dts/kirkwood-dns325.dts delete mode 100644 arch/arm/dts/kirkwood-dnskw.dtsi delete mode 100644 arch/arm/dts/kirkwood-dockstar.dts delete mode 100644 arch/arm/dts/kirkwood-dreamplug.dts delete mode 100644 arch/arm/dts/kirkwood-ds109.dts delete mode 100644 arch/arm/dts/kirkwood-goflexnet.dts delete mode 100644 arch/arm/dts/kirkwood-guruplug-server-plus.dts delete mode 100644 arch/arm/dts/kirkwood-ib62x0.dts delete mode 100644 arch/arm/dts/kirkwood-iconnect.dts delete mode 100644 arch/arm/dts/kirkwood-is2.dts delete mode 100644 arch/arm/dts/kirkwood-lschlv2.dts delete mode 100644 arch/arm/dts/kirkwood-lsxhl.dts delete mode 100644 arch/arm/dts/kirkwood-lsxl.dtsi delete mode 100644 arch/arm/dts/kirkwood-net2big.dts delete mode 100644 arch/arm/dts/kirkwood-netxbig.dtsi delete mode 100644 arch/arm/dts/kirkwood-ns2-common.dtsi delete mode 100644 arch/arm/dts/kirkwood-ns2.dts delete mode 100644 arch/arm/dts/kirkwood-ns2lite.dts delete mode 100644 arch/arm/dts/kirkwood-ns2max.dts delete mode 100644 arch/arm/dts/kirkwood-ns2mini.dts delete mode 100644 arch/arm/dts/kirkwood-nsa310s.dts delete mode 100644 arch/arm/dts/kirkwood-nsa325.dts delete mode 100644 arch/arm/dts/kirkwood-nsa3x0-common.dtsi delete mode 100644 arch/arm/dts/kirkwood-openrd-base.dts delete mode 100644 arch/arm/dts/kirkwood-openrd-client.dts delete mode 100644 arch/arm/dts/kirkwood-openrd-ultimate.dts delete mode 100644 arch/arm/dts/kirkwood-openrd.dtsi delete mode 100644 arch/arm/dts/kirkwood-pogo_e02.dts delete mode 100644 arch/arm/dts/kirkwood-pogoplug-series-4.dts delete mode 100644 arch/arm/dts/kirkwood-sheevaplug-common.dtsi delete mode 100644 arch/arm/dts/kirkwood-sheevaplug.dts delete mode 100644 arch/arm/dts/kirkwood-synology.dtsi delete mode 100644 arch/arm/dts/kirkwood.dtsi diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index d85a33055c..896476a823 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -47,33 +47,7 @@ dtb-$(CONFIG_ARCH_DAVINCI) += \ dtb-$(CONFIG_ARCH_KIRKWOOD) += \ kirkwood-atl-sbx81lifkw.dtb \ - kirkwood-atl-sbx81lifxcat.dtb \ - kirkwood-blackarmor-nas220.dtb \ - kirkwood-d2net.dtb \ - kirkwood-dns325.dtb \ - kirkwood-dockstar.dtb \ - kirkwood-dreamplug.dtb \ - kirkwood-ds109.dtb \ - kirkwood-goflexnet.dtb \ - kirkwood-guruplug-server-plus.dtb \ - kirkwood-ib62x0.dtb \ - kirkwood-iconnect.dtb \ - kirkwood-is2.dtb \ - kirkwood-lsxhl.dtb \ - kirkwood-lschlv2.dtb \ - kirkwood-net2big.dtb \ - kirkwood-ns2.dtb \ - kirkwood-ns2lite.dtb \ - kirkwood-ns2max.dtb \ - kirkwood-ns2mini.dtb \ - kirkwood-nsa310s.dtb \ - kirkwood-nsa325.dtb \ - kirkwood-openrd-base.dtb \ - kirkwood-openrd-client.dtb \ - kirkwood-openrd-ultimate.dtb \ - kirkwood-pogo_e02.dtb \ - kirkwood-pogoplug-series-4.dtb \ - kirkwood-sheevaplug.dtb + kirkwood-atl-sbx81lifxcat.dtb dtb-$(CONFIG_MACH_S900) += \ bubblegum_96.dtb diff --git a/arch/arm/dts/kirkwood-6192.dtsi b/arch/arm/dts/kirkwood-6192.dtsi deleted file mode 100644 index 396bcba08a..0000000000 --- a/arch/arm/dts/kirkwood-6192.dtsi +++ /dev/null @@ -1,88 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/ { - mbus@f1000000 { - pciec: pcie@82000000 { - compatible = "marvell,kirkwood-pcie"; - status = "disabled"; - device_type = "pci"; - - #address-cells = <3>; - #size-cells = <2>; - - bus-range = <0x00 0xff>; - - ranges = - <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 - 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ - 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>; - - pcie0: pcie@1,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>; - reg = <0x0800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 - 0x81000000 0 0 0x81000000 0x1 0 1 0>; - bus-range = <0x00 0xff>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &intc 9>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <0>; - clocks = <&gate_clk 2>; - status = "disabled"; - }; - }; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - compatible = "marvell,88f6192-pinctrl"; - - pmx_sata0: pmx-sata0 { - marvell,pins = "mpp5", "mpp21", "mpp23"; - marvell,function = "sata0"; - }; - pmx_sata1: pmx-sata1 { - marvell,pins = "mpp4", "mpp20", "mpp22"; - marvell,function = "sata1"; - }; - pmx_sdio: pmx-sdio { - marvell,pins = "mpp12", "mpp13", "mpp14", - "mpp15", "mpp16", "mpp17"; - marvell,function = "sdio"; - }; - }; - - rtc: rtc@10300 { - compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc"; - reg = <0x10300 0x20>; - interrupts = <53>; - clocks = <&gate_clk 7>; - }; - - sata: sata@80000 { - compatible = "marvell,orion-sata"; - reg = <0x80000 0x5000>; - interrupts = <21>; - clocks = <&gate_clk 14>, <&gate_clk 15>; - clock-names = "0", "1"; - phys = <&sata_phy0>, <&sata_phy1>; - phy-names = "port0", "port1"; - status = "disabled"; - }; - - sdio: mvsdio@90000 { - compatible = "marvell,orion-sdio"; - reg = <0x90000 0x200>; - interrupts = <28>; - clocks = <&gate_clk 4>; - bus-width = <4>; - cap-sdio-irq; - cap-sd-highspeed; - cap-mmc-highspeed; - status = "disabled"; - }; - }; -}; diff --git a/arch/arm/dts/kirkwood-6281.dtsi b/arch/arm/dts/kirkwood-6281.dtsi deleted file mode 100644 index faa05849a4..0000000000 --- a/arch/arm/dts/kirkwood-6281.dtsi +++ /dev/null @@ -1,90 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/ { - mbus@f1000000 { - pciec: pcie@82000000 { - compatible = "marvell,kirkwood-pcie"; - status = "disabled"; - device_type = "pci"; - - #address-cells = <3>; - #size-cells = <2>; - - bus-range = <0x00 0xff>; - - ranges = - <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 - 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ - 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>; - - pcie0: pcie@1,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>; - reg = <0x0800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 - 0x81000000 0 0 0x81000000 0x1 0 1 0>; - bus-range = <0x00 0xff>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &intc 9>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <0>; - clocks = <&gate_clk 2>; - status = "disabled"; - }; - }; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - compatible = "marvell,88f6281-pinctrl"; - - pmx_sata0: pmx-sata0 { - marvell,pins = "mpp5", "mpp21", "mpp23"; - marvell,function = "sata0"; - }; - pmx_sata1: pmx-sata1 { - marvell,pins = "mpp4", "mpp20", "mpp22"; - marvell,function = "sata1"; - }; - pmx_sdio: pmx-sdio { - marvell,pins = "mpp12", "mpp13", "mpp14", - "mpp15", "mpp16", "mpp17"; - marvell,function = "sdio"; - }; - }; - - rtc: rtc@10300 { - compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc"; - reg = <0x10300 0x20>; - interrupts = <53>; - clocks = <&gate_clk 7>; - }; - - sata: sata@80000 { - compatible = "marvell,orion-sata"; - reg = <0x80000 0x5000>; - interrupts = <21>; - clocks = <&gate_clk 14>, <&gate_clk 15>; - clock-names = "0", "1"; - phys = <&sata_phy0>, <&sata_phy1>; - phy-names = "port0", "port1"; - status = "disabled"; - }; - - sdio: mvsdio@90000 { - compatible = "marvell,orion-sdio"; - reg = <0x90000 0x200>; - interrupts = <28>; - clocks = <&gate_clk 4>; - pinctrl-0 = <&pmx_sdio>; - pinctrl-names = "default"; - bus-width = <4>; - cap-sdio-irq; - cap-sd-highspeed; - cap-mmc-highspeed; - status = "disabled"; - }; - }; -}; diff --git a/arch/arm/dts/kirkwood-6282.dtsi b/arch/arm/dts/kirkwood-6282.dtsi deleted file mode 100644 index e732c501ea..0000000000 --- a/arch/arm/dts/kirkwood-6282.dtsi +++ /dev/null @@ -1,161 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/ { - mbus@f1000000 { - pciec: pcie@82000000 { - compatible = "marvell,kirkwood-pcie"; - status = "disabled"; - device_type = "pci"; - - #address-cells = <3>; - #size-cells = <2>; - - bus-range = <0x00 0xff>; - - ranges = - <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 - 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 - 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 - 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ - 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */ - 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 1.0 MEM */ - 0x81000000 0x2 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 1.0 IO */>; - - pcie0: pcie@1,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>; - reg = <0x0800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 - 0x81000000 0 0 0x81000000 0x1 0 1 0>; - bus-range = <0x00 0xff>; - interrupt-names = "intx", "error"; - interrupts = <9>, <44>; - interrupt-map-mask = <0 0 0 7>; - interrupt-map = <0 0 0 1 &pcie0_intc 0>, - <0 0 0 2 &pcie0_intc 1>, - <0 0 0 3 &pcie0_intc 2>, - <0 0 0 4 &pcie0_intc 3>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <0>; - clocks = <&gate_clk 2>; - status = "disabled"; - - pcie0_intc: interrupt-controller { - interrupt-controller; - #interrupt-cells = <1>; - }; - }; - - pcie1: pcie@2,0 { - device_type = "pci"; - assigned-addresses = <0x82001000 0 0x00044000 0 0x2000>; - reg = <0x1000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 - 0x81000000 0 0 0x81000000 0x2 0 1 0>; - bus-range = <0x00 0xff>; - interrupt-names = "intx", "error"; - interrupts = <10>, <45>; - interrupt-map-mask = <0 0 0 7>; - interrupt-map = <0 0 0 1 &pcie1_intc 0>, - <0 0 0 2 &pcie1_intc 1>, - <0 0 0 3 &pcie1_intc 2>, - <0 0 0 4 &pcie1_intc 3>; - marvell,pcie-port = <1>; - marvell,pcie-lane = <0>; - clocks = <&gate_clk 18>; - status = "disabled"; - - pcie1_intc: interrupt-controller { - interrupt-controller; - #interrupt-cells = <1>; - }; - }; - }; - }; - ocp@f1000000 { - - pinctrl: pin-controller@10000 { - compatible = "marvell,88f6282-pinctrl"; - - pmx_sata0: pmx-sata0 { - marvell,pins = "mpp5", "mpp21", "mpp23"; - marvell,function = "sata0"; - }; - pmx_sata1: pmx-sata1 { - marvell,pins = "mpp4", "mpp20", "mpp22"; - marvell,function = "sata1"; - }; - - /* - * Default I2C1 pinctrl setting on mpp36/mpp37, - * overwrite marvell,pins on board level if required. - */ - pmx_twsi1: pmx-twsi1 { - marvell,pins = "mpp36", "mpp37"; - marvell,function = "twsi1"; - }; - - pmx_sdio: pmx-sdio { - marvell,pins = "mpp12", "mpp13", "mpp14", - "mpp15", "mpp16", "mpp17"; - marvell,function = "sdio"; - }; - }; - - thermal: thermal@10078 { - compatible = "marvell,kirkwood-thermal"; - reg = <0x10078 0x4>; - status = "okay"; - }; - - rtc: rtc@10300 { - compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc"; - reg = <0x10300 0x20>; - interrupts = <53>; - clocks = <&gate_clk 7>; - }; - - i2c1: i2c@11100 { - compatible = "marvell,mv64xxx-i2c"; - reg = <0x11100 0x20>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <32>; - clock-frequency = <100000>; - clocks = <&gate_clk 7>; - pinctrl-0 = <&pmx_twsi1>; - pinctrl-names = "default"; - status = "disabled"; - }; - - sata: sata@80000 { - compatible = "marvell,orion-sata"; - reg = <0x80000 0x5000>; - interrupts = <21>; - clocks = <&gate_clk 14>, <&gate_clk 15>; - clock-names = "0", "1"; - phys = <&sata_phy0>, <&sata_phy1>; - phy-names = "port0", "port1"; - status = "disabled"; - }; - - sdio: mvsdio@90000 { - compatible = "marvell,orion-sdio"; - reg = <0x90000 0x200>; - interrupts = <28>; - clocks = <&gate_clk 4>; - pinctrl-0 = <&pmx_sdio>; - pinctrl-names = "default"; - bus-width = <4>; - cap-sdio-irq; - cap-sd-highspeed; - cap-mmc-highspeed; - status = "disabled"; - }; - }; -}; diff --git a/arch/arm/dts/kirkwood-98dx4122.dtsi b/arch/arm/dts/kirkwood-98dx4122.dtsi deleted file mode 100644 index 299c147298..0000000000 --- a/arch/arm/dts/kirkwood-98dx4122.dtsi +++ /dev/null @@ -1,53 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/ { - mbus@f1000000 { - pciec: pcie@82000000 { - compatible = "marvell,kirkwood-pcie"; - status = "disabled"; - device_type = "pci"; - - #address-cells = <3>; - #size-cells = <2>; - - bus-range = <0x00 0xff>; - - ranges = - <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 - 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ - 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>; - - pcie0: pcie@1,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>; - reg = <0x0800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 - 0x81000000 0 0 0x81000000 0x1 0 1 0>; - bus-range = <0x00 0xff>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &intc 9>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <0>; - clocks = <&gate_clk 2>; - status = "disabled"; - }; - }; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - compatible = "marvell,98dx4122-pinctrl"; - - }; - }; -}; - -&sata_phy0 { - status = "disabled"; -}; - -&sata_phy1 { - status = "disabled"; -}; diff --git a/arch/arm/dts/kirkwood-blackarmor-nas220.dts b/arch/arm/dts/kirkwood-blackarmor-nas220.dts deleted file mode 100644 index 07fbfca444..0000000000 --- a/arch/arm/dts/kirkwood-blackarmor-nas220.dts +++ /dev/null @@ -1,172 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Device Tree file for Seagate Blackarmor NAS220 - * - * Copyright (C) 2014 Evgeni Dobrev <evgeni(a)studio-punkt.com> - */ - -/dts-v1/; - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> -#include "kirkwood.dtsi" -#include "kirkwood-6192.dtsi" - -/ { - model = "Seagate Blackarmor NAS220"; - compatible = "seagate,blackarmor-nas220","marvell,kirkwood-88f6192", - "marvell,kirkwood"; - - memory { /* 128 MB */ - device_type = "memory"; - reg = <0x00000000 0x8000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8"; - stdout-path = &uart0; - }; - - gpio_poweroff { - compatible = "gpio-poweroff"; - gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; - }; - - gpio_keys { - compatible = "gpio-keys"; - - reset { - label = "Reset"; - linux,code = <KEY_POWER>; - gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; - }; - - button { - label = "Power"; - linux,code = <KEY_SLEEP>; - gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - blue-power { - label = "nas220:blue:power"; - gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "default-on"; - }; - }; - - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_power_sata0 &pmx_power_sata1>; - pinctrl-names = "default"; - - sata0_power: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "SATA0 Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio0 24 GPIO_ACTIVE_LOW>; - }; - - sata1_power: regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - regulator-name = "SATA1 Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio0 28 GPIO_ACTIVE_LOW>; - }; - }; -}; - -/* - * Serial port routed to connector CN5 - * - * pin 1 - TX (CPU's TX) - * pin 4 - RX (CPU's RX) - * pin 6 - GND - */ -&uart0 { - status = "okay"; -}; - -&pinctrl { - pinctrl-0 = <&pmx_button_reset &pmx_button_power>; - pinctrl-names = "default"; - - pmx_act_sata0: pmx-act-sata0 { - marvell,pins = "mpp15"; - marvell,function = "sata0"; - }; - - pmx_act_sata1: pmx-act-sata1 { - marvell,pins = "mpp16"; - marvell,function = "sata1"; - }; - - pmx_power_sata0: pmx-power-sata0 { - marvell,pins = "mpp24"; - marvell,function = "gpio"; - }; - - pmx_power_sata1: pmx-power-sata1 { - marvell,pins = "mpp28"; - marvell,function = "gpio"; - }; - - pmx_button_reset: pmx-button-reset { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - - pmx_button_power: pmx-button-power { - marvell,pins = "mpp26"; - marvell,function = "gpio"; - }; -}; - -&sata { - status = "okay"; - nr-ports = <2>; -}; - -&i2c0 { - status = "okay"; - - adt7476: thermal@2e { - compatible = "adi,adt7476"; - reg = <0x2e>; - }; -}; - -&nand { - status = "okay"; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@8 { - reg = <8>; - }; -}; - -&eth0 { - status = "okay"; - - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; diff --git a/arch/arm/dts/kirkwood-d2net.dts b/arch/arm/dts/kirkwood-d2net.dts deleted file mode 100644 index bd3b266dd7..0000000000 --- a/arch/arm/dts/kirkwood-d2net.dts +++ /dev/null @@ -1,45 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Device Tree file for d2 Network v2 - * - * Copyright (C) 2014 Simon Guinot <simon.guinot(a)sequanux.org> - * -*/ - -/dts-v1/; - -#include <dt-bindings/leds/leds-ns2.h> -#include "kirkwood-netxbig.dtsi" - -/ { - model = "LaCie d2 Network v2"; - compatible = "lacie,d2net_v2", "lacie,netxbig", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x10000000>; - }; - - ns2-leds { - compatible = "lacie,ns2-leds"; - - blue-sata { - label = "d2net_v2:blue:sata"; - slow-gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; - cmd-gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; - modes-map = <NS_V2_LED_OFF 1 0 - NS_V2_LED_ON 0 1 - NS_V2_LED_ON 1 1 - NS_V2_LED_SATA 0 0>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - red-fail { - label = "d2net_v2:red:fail"; - gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; - }; - }; -}; diff --git a/arch/arm/dts/kirkwood-dns325.dts b/arch/arm/dts/kirkwood-dns325.dts deleted file mode 100644 index 94d9c06cbb..0000000000 --- a/arch/arm/dts/kirkwood-dns325.dts +++ /dev/null @@ -1,63 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include "kirkwood-dnskw.dtsi" - -/ { - model = "D-Link DNS-325 NAS (Rev A1)"; - compatible = "dlink,dns-325-a1", "dlink,dns-325", "dlink,dns-kirkwood", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x10000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk"; - stdout-path = &uart0; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_led_power &pmx_led_red_usb_325 - &pmx_led_red_left_hdd &pmx_led_red_right_hdd - &pmx_led_white_usb>; - pinctrl-names = "default"; - - white-power { - label = "dns325:white:power"; - gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - white-usb { - label = "dns325:white:usb"; - gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; /* GPIO 43 */ - }; - red-l_hdd { - label = "dns325:red:l_hdd"; - gpios = <&gpio0 28 GPIO_ACTIVE_LOW>; - }; - red-r_hdd { - label = "dns325:red:r_hdd"; - gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; - }; - red-usb { - label = "dns325:red:usb"; - gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; - }; - }; - - ocp@f1000000 { - i2c@11000 { - status = "okay"; - - lm75: lm75@48 { - compatible = "national,lm75"; - reg = <0x48>; - }; - }; - serial@12000 { - status = "okay"; - }; - }; -}; diff --git a/arch/arm/dts/kirkwood-dnskw.dtsi b/arch/arm/dts/kirkwood-dnskw.dtsi deleted file mode 100644 index cbaf06f2f7..0000000000 --- a/arch/arm/dts/kirkwood-dnskw.dtsi +++ /dev/null @@ -1,235 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - model = "D-Link DNS NASes (kirkwood-based)"; - compatible = "dlink,dns-kirkwood", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_button_power &pmx_button_unmount - &pmx_button_reset>; - pinctrl-names = "default"; - - power { - label = "Power button"; - linux,code = <KEY_POWER>; - gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; - }; - eject { - label = "USB unmount button"; - linux,code = <KEY_EJECTCD>; - gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - }; - reset { - label = "Reset button"; - linux,code = <KEY_RESTART>; - gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; - }; - }; - - gpio_fan { - /* Fan: ADDA AD045HB-G73 40mm 6000rpm@5v */ - compatible = "gpio-fan"; - pinctrl-0 = <&pmx_fan_high_speed &pmx_fan_low_speed>; - pinctrl-names = "default"; - gpios = <&gpio1 14 GPIO_ACTIVE_LOW - &gpio1 13 GPIO_ACTIVE_LOW>; - gpio-fan,speed-map = <0 0 - 3000 1 - 6000 2>; - }; - - gpio_poweroff { - compatible = "gpio-poweroff"; - pinctrl-0 = <&pmx_power_off>; - pinctrl-names = "default"; - gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - - pinctrl-0 = <&pmx_power_back_on &pmx_present_sata0 - &pmx_present_sata1 &pmx_fan_tacho - &pmx_temp_alarm>; - pinctrl-names = "default"; - - pmx_sata0: pmx-sata0 { - marvell,pins = "mpp20"; - marvell,function = "sata1"; - }; - pmx_sata1: pmx-sata1 { - marvell,pins = "mpp21"; - marvell,function = "sata0"; - }; - pmx_led_power: pmx-led-power { - marvell,pins = "mpp26"; - marvell,function = "gpio"; - }; - pmx_led_red_right_hdd: pmx-led-red-right-hdd { - marvell,pins = "mpp27"; - marvell,function = "gpio"; - }; - pmx_led_red_left_hdd: pmx-led-red-left-hdd { - marvell,pins = "mpp28"; - marvell,function = "gpio"; - }; - pmx_led_red_usb_325: pmx-led-red-usb-325 { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - pmx_button_power: pmx-button-power { - marvell,pins = "mpp34"; - marvell,function = "gpio"; - }; - pmx_led_red_usb_320: pmx-led-red-usb-320 { - marvell,pins = "mpp35"; - marvell,function = "gpio"; - }; - pmx_power_off: pmx-power-off { - marvell,pins = "mpp36"; - marvell,function = "gpio"; - }; - pmx_power_back_on: pmx-power-back-on { - marvell,pins = "mpp37"; - marvell,function = "gpio"; - }; - pmx_power_sata0: pmx-power-sata0 { - marvell,pins = "mpp39"; - marvell,function = "gpio"; - }; - pmx_power_sata1: pmx-power-sata1 { - marvell,pins = "mpp40"; - marvell,function = "gpio"; - }; - pmx_present_sata0: pmx-present-sata0 { - marvell,pins = "mpp41"; - marvell,function = "gpio"; - }; - pmx_present_sata1: pmx-present-sata1 { - marvell,pins = "mpp42"; - marvell,function = "gpio"; - }; - pmx_led_white_usb: pmx-led-white-usb { - marvell,pins = "mpp43"; - marvell,function = "gpio"; - }; - pmx_fan_tacho: pmx-fan-tacho { - marvell,pins = "mpp44"; - marvell,function = "gpio"; - }; - pmx_fan_high_speed: pmx-fan-high-speed { - marvell,pins = "mpp45"; - marvell,function = "gpio"; - }; - pmx_fan_low_speed: pmx-fan-low-speed { - marvell,pins = "mpp46"; - marvell,function = "gpio"; - }; - pmx_button_unmount: pmx-button-unmount { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - pmx_button_reset: pmx-button-reset { - marvell,pins = "mpp48"; - marvell,function = "gpio"; - }; - pmx_temp_alarm: pmx-temp-alarm { - marvell,pins = "mpp49"; - marvell,function = "gpio"; - }; - }; - sata@80000 { - pinctrl-0 = <&pmx_sata0 &pmx_sata1>; - pinctrl-names = "default"; - status = "okay"; - nr-ports = <2>; - }; - }; - - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_power_sata0 &pmx_power_sata1>; - pinctrl-names = "default"; - - sata0_power: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "SATA0 Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio1 7 0>; - }; - sata1_power: regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - regulator-name = "SATA1 Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio1 8 0>; - }; - }; -}; - -&nand { - status = "okay"; - chip-delay = <35>; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - read-only; - }; - - partition@100000 { - label = "uImage"; - reg = <0x0100000 0x500000>; - }; - - partition@600000 { - label = "ramdisk"; - reg = <0x0600000 0x500000>; - }; - - partition@b00000 { - label = "image"; - reg = <0x0b00000 0x6600000>; - }; - - partition@7100000 { - label = "mini firmware"; - reg = <0x7100000 0xa00000>; - }; - - partition@7b00000 { - label = "config"; - reg = <0x7b00000 0x500000>; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@8 { - reg = <8>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; diff --git a/arch/arm/dts/kirkwood-dockstar.dts b/arch/arm/dts/kirkwood-dockstar.dts deleted file mode 100644 index 6a3f1bf6d9..0000000000 --- a/arch/arm/dts/kirkwood-dockstar.dts +++ /dev/null @@ -1,110 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - model = "Seagate FreeAgent Dockstar"; - compatible = "seagate,dockstar", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x8000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; - stdout-path = &uart0; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pmx_usb_power_enable: pmx-usb-power-enable { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - pmx_led_green: pmx-led-green { - marvell,pins = "mpp46"; - marvell,function = "gpio"; - }; - pmx_led_orange: pmx-led-orange { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - }; - serial@12000 { - status = "ok"; - }; - }; - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_led_green &pmx_led_orange>; - pinctrl-names = "default"; - - health { - label = "status:green:health"; - gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - fault { - label = "status:orange:fault"; - gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - }; - }; - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_usb_power_enable>; - pinctrl-names = "default"; - - usb_power: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "USB Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio0 29 0>; - }; - }; -}; - -&nand { - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - read-only; - }; - - partition@100000 { - label = "uImage"; - reg = <0x0100000 0x400000>; - }; - - partition@500000 { - label = "data"; - reg = <0x0500000 0xfb00000>; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@0 { - compatible = "marvell,88e1116"; - reg = <0>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; diff --git a/arch/arm/dts/kirkwood-dreamplug.dts b/arch/arm/dts/kirkwood-dreamplug.dts deleted file mode 100644 index e9eea22fc9..0000000000 --- a/arch/arm/dts/kirkwood-dreamplug.dts +++ /dev/null @@ -1,131 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - model = "Globalscale Technologies Dreamplug"; - compatible = "globalscale,dreamplug-003-ds2001", "globalscale,dreamplug", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x20000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk"; - stdout-path = &uart0; - }; - - aliases { - spi0 = &spi0; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pmx_led_bluetooth: pmx-led-bluetooth { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - pmx_led_wifi: pmx-led-wifi { - marvell,pins = "mpp48"; - marvell,function = "gpio"; - }; - pmx_led_wifi_ap: pmx-led-wifi-ap { - marvell,pins = "mpp49"; - marvell,function = "gpio"; - }; - }; - serial@12000 { - status = "ok"; - }; - - spi@10600 { - status = "okay"; - - m25p40@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "mxicy,mx25l1606e", "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <50000000>; - mode = <0>; - - partition@0 { - reg = <0x0 0x80000>; - label = "u-boot"; - }; - - partition@100000 { - reg = <0x100000 0x10000>; - label = "u-boot env"; - }; - - partition@180000 { - reg = <0x180000 0x10000>; - label = "dtb"; - }; - }; - }; - - sata@80000 { - status = "okay"; - nr-ports = <1>; - }; - - mvsdio@90000 { - pinctrl-0 = <&pmx_sdio>; - pinctrl-names = "default"; - status = "okay"; - /* No CD or WP GPIOs */ - broken-cd; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_led_bluetooth &pmx_led_wifi - &pmx_led_wifi_ap >; - pinctrl-names = "default"; - - bluetooth { - label = "dreamplug:blue:bluetooth"; - gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - }; - wifi { - label = "dreamplug:green:wifi"; - gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; - }; - wifi-ap { - label = "dreamplug:green:wifi_ap"; - gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@0 { - reg = <0>; - }; - - ethphy1: ethernet-phy@1 { - reg = <1>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; - -&eth1 { - status = "okay"; - ethernet1-port@0 { - phy-handle = <&ethphy1>; - }; -}; diff --git a/arch/arm/dts/kirkwood-ds109.dts b/arch/arm/dts/kirkwood-ds109.dts deleted file mode 100644 index 29982e7acb..0000000000 --- a/arch/arm/dts/kirkwood-ds109.dts +++ /dev/null @@ -1,40 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Andrew Lunn <andrew(a)lunn.ch> - * Ben Peddell <klightspeed(a)killerwolves.net> - * - */ - -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" -#include "kirkwood-synology.dtsi" - -/ { - model = "Synology DS109, DS110, DS110jv20"; - compatible = "synology,ds109", "synology,ds110jv20", - "synology,ds110", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x8000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8"; - stdout-path = &uart0; - }; - - gpio-fan-150-32-35 { - status = "okay"; - }; - - gpio-leds-hdd-21-1 { - status = "okay"; - }; -}; - -&rs5c372 { - status = "okay"; -}; diff --git a/arch/arm/dts/kirkwood-goflexnet.dts b/arch/arm/dts/kirkwood-goflexnet.dts deleted file mode 100644 index 02d87e0a10..0000000000 --- a/arch/arm/dts/kirkwood-goflexnet.dts +++ /dev/null @@ -1,190 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - model = "Seagate GoFlex Net"; - compatible = "seagate,goflexnet", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x8000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; - stdout-path = &uart0; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pmx_usb_power_enable: pmx-usb-power-enable { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - pmx_led_right_cap_0: pmx-led_right_cap_0 { - marvell,pins = "mpp38"; - marvell,function = "gpio"; - }; - pmx_led_right_cap_1: pmx-led_right_cap_1 { - marvell,pins = "mpp39"; - marvell,function = "gpio"; - }; - pmx_led_right_cap_2: pmx-led_right_cap_2 { - marvell,pins = "mpp40"; - marvell,function = "gpio"; - }; - pmx_led_right_cap_3: pmx-led_right_cap_3 { - marvell,pins = "mpp41"; - marvell,function = "gpio"; - }; - pmx_led_left_cap_0: pmx-led_left_cap_0 { - marvell,pins = "mpp42"; - marvell,function = "gpio"; - }; - pmx_led_left_cap_1: pmx-led_left_cap_1 { - marvell,pins = "mpp43"; - marvell,function = "gpio"; - }; - pmx_led_left_cap_2: pmx-led_left_cap_2 { - marvell,pins = "mpp44"; - marvell,function = "gpio"; - }; - pmx_led_left_cap_3: pmx-led_left_cap_3 { - marvell,pins = "mpp45"; - marvell,function = "gpio"; - }; - pmx_led_green: pmx-led_green { - marvell,pins = "mpp46"; - marvell,function = "gpio"; - }; - pmx_led_orange: pmx-led_orange { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - }; - serial@12000 { - status = "ok"; - }; - - sata@80000 { - status = "okay"; - nr-ports = <2>; - }; - - }; - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = < &pmx_led_orange - &pmx_led_left_cap_0 &pmx_led_left_cap_1 - &pmx_led_left_cap_2 &pmx_led_left_cap_3 - &pmx_led_right_cap_0 &pmx_led_right_cap_1 - &pmx_led_right_cap_2 &pmx_led_right_cap_3 - >; - pinctrl-names = "default"; - - health { - label = "status:green:health"; - gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - fault { - label = "status:orange:fault"; - gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - }; - left0 { - label = "status:white:left0"; - gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; - }; - left1 { - label = "status:white:left1"; - gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; - }; - left2 { - label = "status:white:left2"; - gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>; - }; - left3 { - label = "status:white:left3"; - gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; - }; - right0 { - label = "status:white:right0"; - gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; - }; - right1 { - label = "status:white:right1"; - gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; - }; - right2 { - label = "status:white:right2"; - gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; - }; - right3 { - label = "status:white:right3"; - gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; - }; - }; - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_usb_power_enable>; - pinctrl-names = "default"; - - usb_power: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "USB Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&nand { - chip-delay = <40>; - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - read-only; - }; - - partition@100000 { - label = "uImage"; - reg = <0x0100000 0x400000>; - }; - - partition@500000 { - label = "pogoplug"; - reg = <0x0500000 0x2000000>; - }; - - partition@2500000 { - label = "root"; - reg = <0x02500000 0xd800000>; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@0 { - reg = <0>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; diff --git a/arch/arm/dts/kirkwood-guruplug-server-plus.dts b/arch/arm/dts/kirkwood-guruplug-server-plus.dts deleted file mode 100644 index ff1260ee3f..0000000000 --- a/arch/arm/dts/kirkwood-guruplug-server-plus.dts +++ /dev/null @@ -1,133 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - model = "Globalscale Technologies Guruplug Server Plus"; - compatible = "globalscale,guruplug-server-plus", "globalscale,guruplug", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x20000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk"; - stdout-path = &uart0; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pmx_led_health_r: pmx-led-health-r { - marvell,pins = "mpp46"; - marvell,function = "gpio"; - }; - pmx_led_health_g: pmx-led-health-g { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - pmx_led_wmode_r: pmx-led-wmode-r { - marvell,pins = "mpp48"; - marvell,function = "gpio"; - }; - pmx_led_wmode_g: pmx-led-wmode-g { - marvell,pins = "mpp49"; - marvell,function = "gpio"; - }; - }; - serial@12000 { - status = "ok"; - }; - - sata@80000 { - status = "okay"; - nr-ports = <1>; - }; - - /* AzureWave AW-GH381 WiFi/BT */ - mvsdio@90000 { - status = "okay"; - non-removable; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g - &pmx_led_wmode_r &pmx_led_wmode_g >; - pinctrl-names = "default"; - - health-r { - label = "guruplug:red:health"; - gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; - }; - health-g { - label = "guruplug:green:health"; - gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - }; - wmode-r { - label = "guruplug:red:wmode"; - gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; - }; - wmode-g { - label = "guruplug:green:wmode"; - gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&nand { - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x00000000 0x00100000>; - read-only; - }; - - partition@100000 { - label = "uImage"; - reg = <0x00100000 0x00400000>; - }; - - partition@500000 { - label = "data"; - reg = <0x00500000 0x1fb00000>; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@0 { - /* Marvell 88E1121R */ - compatible = "ethernet-phy-id0141.0cb0", - "ethernet-phy-ieee802.3-c22"; - reg = <0>; - }; - - ethphy1: ethernet-phy@1 { - /* Marvell 88E1121R */ - compatible = "ethernet-phy-id0141.0cb0", - "ethernet-phy-ieee802.3-c22"; - reg = <1>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - phy-connection-type = "rgmii-id"; - }; -}; - -&eth1 { - status = "okay"; - ethernet1-port@0 { - phy-handle = <&ethphy1>; - phy-connection-type = "rgmii-id"; - }; -}; diff --git a/arch/arm/dts/kirkwood-ib62x0.dts b/arch/arm/dts/kirkwood-ib62x0.dts deleted file mode 100644 index 962a910a6f..0000000000 --- a/arch/arm/dts/kirkwood-ib62x0.dts +++ /dev/null @@ -1,146 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)"; - compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x10000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk"; - stdout-path = &uart0; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pmx_led_os_red: pmx-led-os-red { - marvell,pins = "mpp22"; - marvell,function = "gpio"; - }; - pmx_power_off: pmx-power-off { - marvell,pins = "mpp24"; - marvell,function = "gpio"; - }; - pmx_led_os_green: pmx-led-os-green { - marvell,pins = "mpp25"; - marvell,function = "gpio"; - }; - pmx_led_usb_transfer: pmx-led-usb-transfer { - marvell,pins = "mpp27"; - marvell,function = "gpio"; - }; - pmx_button_reset: pmx-button-reset { - marvell,pins = "mpp28"; - marvell,function = "gpio"; - }; - pmx_button_usb_copy: pmx-button-usb-copy { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - }; - - serial@12000 { - status = "okay"; - }; - - sata@80000 { - status = "okay"; - nr-ports = <2>; - }; - }; - - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_button_reset &pmx_button_usb_copy>; - pinctrl-names = "default"; - - copy { - label = "USB Copy"; - linux,code = <KEY_COPY>; - gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; - }; - reset { - label = "Reset"; - linux,code = <KEY_RESTART>; - gpios = <&gpio0 28 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_led_os_red &pmx_led_os_green - &pmx_led_usb_transfer>; - pinctrl-names = "default"; - - green-os { - label = "ib62x0:green:os"; - gpios = <&gpio0 25 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - red-os { - label = "ib62x0:red:os"; - gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; - }; - usb-copy { - label = "ib62x0:red:usb_copy"; - gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>; - }; - }; - - gpio_poweroff { - compatible = "gpio-poweroff"; - pinctrl-0 = <&pmx_power_off>; - pinctrl-names = "default"; - gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>; - }; -}; - -&nand { - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0xe0000>; - }; - - partition@e0000 { - label = "u-boot environment"; - reg = <0xe0000 0x20000>; - }; - - partition@100000 { - label = "uImage"; - reg = <0x0100000 0x600000>; - }; - - partition@700000 { - label = "root"; - reg = <0x0700000 0xf900000>; - }; - -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@8 { - reg = <8>; - }; -}; - -&eth0 { - status = "okay"; - - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; diff --git a/arch/arm/dts/kirkwood-iconnect.dts b/arch/arm/dts/kirkwood-iconnect.dts deleted file mode 100644 index 4a512d8091..0000000000 --- a/arch/arm/dts/kirkwood-iconnect.dts +++ /dev/null @@ -1,195 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - model = "Iomega Iconnect"; - compatible = "iom,iconnect-1.1", "iom,iconnect", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x10000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk"; - stdout-path = &uart0; - linux,initrd-start = <0x4500040>; - linux,initrd-end = <0x4800000>; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pmx_button_reset: pmx-button-reset { - marvell,pins = "mpp12"; - marvell,function = "gpio"; - }; - pmx_button_otb: pmx-button-otb { - marvell,pins = "mpp35"; - marvell,function = "gpio"; - }; - pmx_led_level: pmx-led-level { - marvell,pins = "mpp41"; - marvell,function = "gpio"; - }; - pmx_led_power_blue: pmx-led-power-blue { - marvell,pins = "mpp42"; - marvell,function = "gpio"; - }; - pmx_led_power_red: pmx-power-red { - marvell,pins = "mpp43"; - marvell,function = "gpio"; - }; - pmx_led_usb1: pmx-led-usb1 { - marvell,pins = "mpp44"; - marvell,function = "gpio"; - }; - pmx_led_usb2: pmx-led-usb2 { - marvell,pins = "mpp45"; - marvell,function = "gpio"; - }; - pmx_led_usb3: pmx-led-usb3 { - marvell,pins = "mpp46"; - marvell,function = "gpio"; - }; - pmx_led_usb4: pmx-led-usb4 { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - pmx_led_otb: pmx-led-otb { - marvell,pins = "mpp48"; - marvell,function = "gpio"; - }; - }; - i2c@11000 { - status = "okay"; - - lm63: lm63@4c { - compatible = "national,lm63"; - reg = <0x4c>; - }; - }; - serial@12000 { - status = "ok"; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = < &pmx_led_level &pmx_led_power_blue - &pmx_led_power_red &pmx_led_usb1 - &pmx_led_usb2 &pmx_led_usb3 - &pmx_led_usb4 &pmx_led_otb >; - pinctrl-names = "default"; - - led-level { - label = "led_level"; - gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; - default-state = "on"; - }; - power-blue { - label = "power:blue"; - gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - power-red { - label = "power:red"; - gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; - }; - usb1 { - label = "usb1:blue"; - gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>; - }; - usb2 { - label = "usb2:blue"; - gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; - }; - usb3 { - label = "usb3:blue"; - gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>; - }; - usb4 { - label = "usb4:blue"; - gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; - }; - otb { - label = "otb:blue"; - gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; - }; - }; - - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = < &pmx_button_reset &pmx_button_otb >; - pinctrl-names = "default"; - - otb { - label = "OTB Button"; - linux,code = <KEY_COPY>; - gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; - debounce-interval = <100>; - }; - reset { - label = "Reset"; - linux,code = <KEY_RESTART>; - gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; - debounce-interval = <100>; - }; - }; -}; - -&nand { - status = "okay"; - - partition@0 { - label = "uboot"; - reg = <0x0000000 0xc0000>; - }; - - partition@a0000 { - label = "env"; - reg = <0xa0000 0x20000>; - }; - - partition@100000 { - label = "zImage"; - reg = <0x100000 0x300000>; - }; - - partition@540000 { - label = "initrd"; - reg = <0x540000 0x300000>; - }; - - partition@980000 { - label = "boot"; - reg = <0x980000 0x1f400000>; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@11 { - reg = <11>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; - -&pciec { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; diff --git a/arch/arm/dts/kirkwood-is2.dts b/arch/arm/dts/kirkwood-is2.dts deleted file mode 100644 index 1bc16a5cdb..0000000000 --- a/arch/arm/dts/kirkwood-is2.dts +++ /dev/null @@ -1,40 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include <dt-bindings/leds/leds-ns2.h> -#include "kirkwood-ns2-common.dtsi" - -/ { - model = "LaCie Internet Space v2"; - compatible = "lacie,inetspace_v2", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x8000000>; - }; - - ocp@f1000000 { - sata@80000 { - pinctrl-0 = <&pmx_ns2_sata0>; - pinctrl-names = "default"; - status = "okay"; - nr-ports = <1>; - }; - }; - - ns2-leds { - compatible = "lacie,ns2-leds"; - - blue-sata { - label = "ns2:blue:sata"; - slow-gpio = <&gpio0 29 0>; - cmd-gpio = <&gpio0 30 0>; - modes-map = <NS_V2_LED_OFF 1 0 - NS_V2_LED_ON 0 1 - NS_V2_LED_ON 1 1 - NS_V2_LED_SATA 0 0>; - }; - }; -}; - -&ethphy0 { reg = <8>; }; diff --git a/arch/arm/dts/kirkwood-lschlv2.dts b/arch/arm/dts/kirkwood-lschlv2.dts deleted file mode 100644 index 1d737d903f..0000000000 --- a/arch/arm/dts/kirkwood-lschlv2.dts +++ /dev/null @@ -1,20 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include "kirkwood-lsxl.dtsi" - -/ { - model = "Buffalo Linkstation LS-CHLv2"; - compatible = "buffalo,lschlv2", "buffalo,lsxl", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x4000000>; - }; - - ocp@f1000000 { - serial@12000 { - status = "okay"; - }; - }; -}; diff --git a/arch/arm/dts/kirkwood-lsxhl.dts b/arch/arm/dts/kirkwood-lsxhl.dts deleted file mode 100644 index a56e0d7977..0000000000 --- a/arch/arm/dts/kirkwood-lsxhl.dts +++ /dev/null @@ -1,20 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include "kirkwood-lsxl.dtsi" - -/ { - model = "Buffalo Linkstation LS-XHL"; - compatible = "buffalo,lsxhl", "buffalo,lsxl", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x10000000>; - }; - - ocp@f1000000 { - serial@12000 { - status = "okay"; - }; - }; -}; diff --git a/arch/arm/dts/kirkwood-lsxl.dtsi b/arch/arm/dts/kirkwood-lsxl.dtsi deleted file mode 100644 index c99c0da093..0000000000 --- a/arch/arm/dts/kirkwood-lsxl.dtsi +++ /dev/null @@ -1,241 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk"; - stdout-path = &uart0; - }; - - aliases { - spi0 = &spi0; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pmx_power_hdd: pmx-power-hdd { - marvell,pins = "mpp10"; - marvell,function = "gpo"; - }; - pmx_usb_vbus: pmx-usb-vbus { - marvell,pins = "mpp11"; - marvell,function = "gpio"; - }; - pmx_fan_high: pmx-fan-high { - marvell,pins = "mpp18"; - marvell,function = "gpo"; - }; - pmx_fan_low: pmx-fan-low { - marvell,pins = "mpp19"; - marvell,function = "gpo"; - }; - pmx_led_function_blue: pmx-led-function-blue { - marvell,pins = "mpp36"; - marvell,function = "gpio"; - }; - pmx_led_alarm: pmx-led-alarm { - marvell,pins = "mpp37"; - marvell,function = "gpio"; - }; - pmx_led_info: pmx-led-info { - marvell,pins = "mpp38"; - marvell,function = "gpio"; - }; - pmx_led_power: pmx-led-power { - marvell,pins = "mpp39"; - marvell,function = "gpio"; - }; - pmx_fan_lock: pmx-fan-lock { - marvell,pins = "mpp40"; - marvell,function = "gpio"; - }; - pmx_button_function: pmx-button-function { - marvell,pins = "mpp41"; - marvell,function = "gpio"; - }; - pmx_power_switch: pmx-power-switch { - marvell,pins = "mpp42"; - marvell,function = "gpio"; - }; - pmx_power_auto_switch: pmx-power-auto-switch { - marvell,pins = "mpp43"; - marvell,function = "gpio"; - }; - pmx_led_function_red: pmx-led-function_red { - marvell,pins = "mpp48"; - marvell,function = "gpio"; - }; - - }; - sata@80000 { - status = "okay"; - nr-ports = <1>; - }; - - spi@10600 { - status = "okay"; - - m25p40@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "m25p40", "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <25000000>; - mode = <0>; - - partition@0 { - reg = <0x0 0x60000>; - label = "uboot"; - read-only; - }; - - partition@60000 { - reg = <0x60000 0x10000>; - label = "dtb"; - read-only; - }; - - partition@70000 { - reg = <0x70000 0x10000>; - label = "uboot_env"; - }; - }; - }; - }; - - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_button_function &pmx_power_switch - &pmx_power_auto_switch>; - pinctrl-names = "default"; - - option { - label = "Function Button"; - linux,code = <KEY_OPTION>; - gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; - }; - reserved { - label = "Power-on Switch"; - linux,code = <KEY_RESERVED>; - linux,input-type = <5>; - gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; - }; - power { - label = "Power-auto Switch"; - linux,code = <KEY_ESC>; - linux,input-type = <5>; - gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; - }; - }; - - gpio_leds { - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_led_function_red &pmx_led_alarm - &pmx_led_info &pmx_led_power - &pmx_led_function_blue>; - pinctrl-names = "default"; - - func_blue { - label = "lsxl:blue:func"; - gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; - }; - - alarm { - label = "lsxl:red:alarm"; - gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; - }; - - info { - label = "lsxl:amber:info"; - gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; - }; - - power { - label = "lsxl:blue:power"; - gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - - func_red { - label = "lsxl:red:func"; - gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; - }; - }; - - gpio_fan { - compatible = "gpio-fan"; - pinctrl-0 = <&pmx_fan_low &pmx_fan_high &pmx_fan_lock>; - pinctrl-names = "default"; - gpios = <&gpio0 19 GPIO_ACTIVE_LOW - &gpio0 18 GPIO_ACTIVE_LOW>; - gpio-fan,speed-map = <0 3 - 1500 2 - 3250 1 - 5000 0>; - alarm-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; - }; - - restart_poweroff { - compatible = "restart-poweroff"; - }; - - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_power_hdd &pmx_usb_vbus>; - pinctrl-names = "default"; - - usb_power: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "USB Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio0 11 0>; - }; - hdd_power: regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - regulator-name = "HDD Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio0 10 0>; - }; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@0 { - reg = <0>; - }; - - ethphy1: ethernet-phy@8 { - reg = <8>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; - -&eth1 { - status = "okay"; - ethernet1-port@0 { - phy-handle = <&ethphy1>; - }; -}; diff --git a/arch/arm/dts/kirkwood-net2big.dts b/arch/arm/dts/kirkwood-net2big.dts deleted file mode 100644 index 3e3ac289e5..0000000000 --- a/arch/arm/dts/kirkwood-net2big.dts +++ /dev/null @@ -1,63 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Device Tree file for LaCie 2Big Network v2 - * - * Copyright (C) 2014 - * - * Andrew Lunn <andrew(a)lunn.ch> - * - * Based on netxbig_v2-setup.c, - * Copyright (C) 2010 Simon Guinot <sguinot(a)lacie.com> - * -*/ - -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" -#include "kirkwood-netxbig.dtsi" - -/ { - model = "LaCie 2Big Network v2"; - compatible = "lacie,net2big_v2", "lacie,netxbig", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x10000000>; - }; - - fan { - compatible = "gpio-fan"; - alarm-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; - }; -}; - -&regulators { - regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - regulator-name = "hdd1power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio0 17 GPIO_ACTIVE_HIGH>; - }; - - clocks { - g762_clk: g762-oscillator { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <32768>; - }; - }; -}; - -&i2c0 { - g762@3e { - compatible = "gmt,g762"; - reg = <0x3e>; - clocks = <&g762_clk>; - }; -}; diff --git a/arch/arm/dts/kirkwood-netxbig.dtsi b/arch/arm/dts/kirkwood-netxbig.dtsi deleted file mode 100644 index b5737026e2..0000000000 --- a/arch/arm/dts/kirkwood-netxbig.dtsi +++ /dev/null @@ -1,232 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Device Tree common file for LaCie 2Big and 5Big Network v2 - * - * Copyright (C) 2014 - * - * Andrew Lunn <andrew(a)lunn.ch> - * - * Based on netxbig_v2-setup.c, - * Copyright (C) 2010 Simon Guinot <sguinot(a)lacie.com> - * -*/ - -#include <dt-bindings/leds/leds-netxbig.h> -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - chosen { - bootargs = "console=ttyS0,115200n8"; - stdout-path = &uart0; - }; - - ocp@f1000000 { - serial@12000 { - status = "okay"; - }; - - spi@10600 { - status = "okay"; - - flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "mxicy,mx25l4005a", "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <20000000>; - mode = <0>; - - partition@0 { - reg = <0x0 0x80000>; - label = "u-boot"; - }; - }; - }; - - sata@80000 { - status = "okay"; - nr-ports = <2>; - }; - - }; - - gpio-keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - - /* - * esc and power represent a three position rocker - * switch. Thus the conventional KEY_POWER does not fit - */ - exc { - label = "Back power switch (on|auto)"; - linux,code = <KEY_ESC>; - linux,input-type = <5>; - gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; - }; - power { - label = "Back power switch (auto|off)"; - linux,code = <KEY_1>; - linux,input-type = <5>; - gpios = <&gpio0 15 GPIO_ACTIVE_LOW>; - }; - option { - label = "Function button"; - linux,code = <KEY_OPTION>; - gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; - }; - - }; - - gpio-poweroff { - compatible = "gpio-poweroff"; - gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; - }; - - regulators: regulators { - status = "okay"; - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - - regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "hdd0power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio0 16 GPIO_ACTIVE_HIGH>; - }; - }; - - netxbig_gpio_ext: netxbig-gpio-ext { - compatible = "lacie,netxbig-gpio-ext"; - - addr-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH - &gpio1 16 GPIO_ACTIVE_HIGH - &gpio1 17 GPIO_ACTIVE_HIGH>; - data-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH - &gpio1 13 GPIO_ACTIVE_HIGH - &gpio1 14 GPIO_ACTIVE_HIGH>; - enable-gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; - }; - - netxbig-leds { - compatible = "lacie,netxbig-leds"; - - gpio-ext = <&netxbig_gpio_ext>; - - timers = <NETXBIG_LED_TIMER1 500 500 - NETXBIG_LED_TIMER2 500 1000>; - - blue-power { - label = "netxbig:blue:power"; - mode-addr = <0>; - mode-val = <NETXBIG_LED_OFF 0 - NETXBIG_LED_ON 1 - NETXBIG_LED_TIMER1 3 - NETXBIG_LED_TIMER2 7>; - bright-addr = <1>; - max-brightness = <7>; - }; - red-power { - label = "netxbig:red:power"; - mode-addr = <0>; - mode-val = <NETXBIG_LED_OFF 0 - NETXBIG_LED_ON 2 - NETXBIG_LED_TIMER1 4>; - bright-addr = <1>; - max-brightness = <7>; - }; - blue-sata0 { - label = "netxbig:blue:sata0"; - mode-addr = <3>; - mode-val = <NETXBIG_LED_OFF 0 - NETXBIG_LED_ON 7 - NETXBIG_LED_SATA 1 - NETXBIG_LED_TIMER1 3>; - bright-addr = <2>; - max-brightness = <7>; - }; - red-sata0 { - label = "netxbig:red:sata0"; - mode-addr = <3>; - mode-val = <NETXBIG_LED_OFF 0 - NETXBIG_LED_ON 2 - NETXBIG_LED_TIMER1 4>; - bright-addr = <2>; - max-brightness = <7>; - }; - blue-sata1 { - label = "netxbig:blue:sata1"; - mode-addr = <4>; - mode-val = <NETXBIG_LED_OFF 0 - NETXBIG_LED_ON 7 - NETXBIG_LED_SATA 1 - NETXBIG_LED_TIMER1 3>; - bright-addr = <2>; - max-brightness = <7>; - }; - red-sata1 { - label = "netxbig:red:sata1"; - mode-addr = <4>; - mode-val = <NETXBIG_LED_OFF 0 - NETXBIG_LED_ON 2 - NETXBIG_LED_TIMER1 4>; - bright-addr = <2>; - max-brightness = <7>; - }; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@0 { - reg = <8>; - }; - - ethphy1: ethernet-phy@1 { - reg = <0>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; - -&pinctrl { - pinctrl-names = "default"; - - pmx_button_function: pmx-button-function { - marvell,pins = "mpp34"; - marvell,function = "gpio"; - }; - pmx_button_power_off: pmx-button-power-off { - marvell,pins = "mpp15"; - marvell,function = "gpio"; - }; - pmx_button_power_on: pmx-button-power-on { - marvell,pins = "mpp13"; - marvell,function = "gpio"; - }; -}; - -&i2c0 { - status = "okay"; - - eeprom@50 { - compatible = "atmel,24c04"; - pagesize = <16>; - reg = <0x50>; - }; -}; diff --git a/arch/arm/dts/kirkwood-ns2-common.dtsi b/arch/arm/dts/kirkwood-ns2-common.dtsi deleted file mode 100644 index 51530ea866..0000000000 --- a/arch/arm/dts/kirkwood-ns2-common.dtsi +++ /dev/null @@ -1,97 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - chosen { - bootargs = "console=ttyS0,115200n8"; - stdout-path = &uart0; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pmx_ns2_sata0: pmx-ns2-sata0 { - marvell,pins = "mpp21"; - marvell,function = "sata0"; - }; - pmx_ns2_sata1: pmx-ns2-sata1 { - marvell,pins = "mpp20"; - marvell,function = "sata1"; - }; - }; - - serial@12000 { - status = "okay"; - }; - - spi@10600 { - status = "okay"; - - flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "mxicy,mx25l4005a", "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <20000000>; - mode = <0>; - - partition@0 { - reg = <0x0 0x80000>; - label = "u-boot"; - }; - }; - }; - - i2c@11000 { - status = "okay"; - - eeprom@50 { - compatible = "atmel,24c04"; - pagesize = <16>; - reg = <0x50>; - }; - }; - }; - - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - - power { - label = "Power push button"; - linux,code = <KEY_POWER>; - gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - red-fail { - label = "ns2:red:fail"; - gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; - }; - }; - - gpio_poweroff { - compatible = "gpio-poweroff"; - gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; - }; - -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@X { - /* overwrite reg property in board file */ - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; diff --git a/arch/arm/dts/kirkwood-ns2.dts b/arch/arm/dts/kirkwood-ns2.dts deleted file mode 100644 index 7b67083e1e..0000000000 --- a/arch/arm/dts/kirkwood-ns2.dts +++ /dev/null @@ -1,40 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include <dt-bindings/leds/leds-ns2.h> -#include "kirkwood-ns2-common.dtsi" - -/ { - model = "LaCie Network Space v2"; - compatible = "lacie,netspace_v2", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x10000000>; - }; - - ocp@f1000000 { - sata@80000 { - pinctrl-0 = <&pmx_ns2_sata0>; - pinctrl-names = "default"; - status = "okay"; - nr-ports = <1>; - }; - }; - - ns2-leds { - compatible = "lacie,ns2-leds"; - - blue-sata { - label = "ns2:blue:sata"; - slow-gpio = <&gpio0 29 0>; - cmd-gpio = <&gpio0 30 0>; - modes-map = <NS_V2_LED_OFF 1 0 - NS_V2_LED_ON 0 1 - NS_V2_LED_ON 1 1 - NS_V2_LED_SATA 0 0>; - }; - }; -}; - -&ethphy0 { reg = <8>; }; diff --git a/arch/arm/dts/kirkwood-ns2lite.dts b/arch/arm/dts/kirkwood-ns2lite.dts deleted file mode 100644 index b0cb5907ed..0000000000 --- a/arch/arm/dts/kirkwood-ns2lite.dts +++ /dev/null @@ -1,35 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include "kirkwood-ns2-common.dtsi" - -/ { - model = "LaCie Network Space Lite v2"; - compatible = "lacie,netspace_lite_v2", "marvell,kirkwood-88f6192", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x8000000>; - }; - - ocp@f1000000 { - sata@80000 { - pinctrl-0 = <&pmx_ns2_sata0>; - pinctrl-names = "default"; - status = "okay"; - nr-ports = <1>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - blue-sata { - label = "ns2:blue:sata"; - gpios = <&gpio0 30 GPIO_ACTIVE_LOW>; - linux,default-trigger = "disk-activity"; - }; - }; -}; - -&ethphy0 { reg = <0>; }; diff --git a/arch/arm/dts/kirkwood-ns2max.dts b/arch/arm/dts/kirkwood-ns2max.dts deleted file mode 100644 index c0a087e774..0000000000 --- a/arch/arm/dts/kirkwood-ns2max.dts +++ /dev/null @@ -1,59 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include <dt-bindings/leds/leds-ns2.h> -#include "kirkwood-ns2-common.dtsi" - -/ { - model = "LaCie Network Space Max v2"; - compatible = "lacie,netspace_max_v2", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x10000000>; - }; - - ocp@f1000000 { - sata@80000 { - pinctrl-0 = <&pmx_ns2_sata0 &pmx_ns2_sata1>; - pinctrl-names = "default"; - status = "okay"; - nr-ports = <2>; - }; - }; - - gpio_fan { - compatible = "gpio-fan"; - gpios = <&gpio0 22 GPIO_ACTIVE_LOW - &gpio0 7 GPIO_ACTIVE_LOW - &gpio1 1 GPIO_ACTIVE_LOW - &gpio0 23 GPIO_ACTIVE_LOW>; - gpio-fan,speed-map = - < 0 0 - 1500 15 - 1700 14 - 1800 13 - 2100 12 - 3100 11 - 3300 10 - 4300 9 - 5500 8>; - alarm-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; - }; - - ns2-leds { - compatible = "lacie,ns2-leds"; - - blue-sata { - label = "ns2:blue:sata"; - slow-gpio = <&gpio0 29 0>; - cmd-gpio = <&gpio0 30 0>; - modes-map = <NS_V2_LED_OFF 1 0 - NS_V2_LED_ON 0 1 - NS_V2_LED_ON 1 1 - NS_V2_LED_SATA 0 0>; - }; - }; -}; - -&ethphy0 { reg = <8>; }; diff --git a/arch/arm/dts/kirkwood-ns2mini.dts b/arch/arm/dts/kirkwood-ns2mini.dts deleted file mode 100644 index 5b9fa14b64..0000000000 --- a/arch/arm/dts/kirkwood-ns2mini.dts +++ /dev/null @@ -1,60 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; - -#include <dt-bindings/leds/leds-ns2.h> -#include "kirkwood-ns2-common.dtsi" - -/ { - /* This machine is embedded in the first LaCie CloudBox product. */ - model = "LaCie Network Space Mini v2"; - compatible = "lacie,netspace_mini_v2", "marvell,kirkwood-88f6192", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x8000000>; - }; - - ocp@f1000000 { - sata@80000 { - pinctrl-0 = <&pmx_ns2_sata0>; - pinctrl-names = "default"; - status = "okay"; - nr-ports = <1>; - }; - }; - - gpio_fan { - compatible = "gpio-fan"; - gpios = <&gpio0 22 GPIO_ACTIVE_LOW - &gpio0 7 GPIO_ACTIVE_LOW - &gpio1 1 GPIO_ACTIVE_LOW - &gpio0 23 GPIO_ACTIVE_LOW>; - gpio-fan,speed-map = - < 0 0 - 3000 15 - 3180 14 - 4140 13 - 4570 12 - 6760 11 - 7140 10 - 7980 9 - 9200 8>; - alarm-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; - }; - - ns2-leds { - compatible = "lacie,ns2-leds"; - - blue-sata { - label = "ns2:blue:sata"; - slow-gpio = <&gpio0 29 0>; - cmd-gpio = <&gpio0 30 0>; - modes-map = <NS_V2_LED_OFF 1 0 - NS_V2_LED_ON 0 1 - NS_V2_LED_ON 1 1 - NS_V2_LED_SATA 0 0>; - }; - }; -}; - -&ethphy0 { reg = <0>; }; diff --git a/arch/arm/dts/kirkwood-nsa310s.dts b/arch/arm/dts/kirkwood-nsa310s.dts deleted file mode 100644 index 09ee76c2a2..0000000000 --- a/arch/arm/dts/kirkwood-nsa310s.dts +++ /dev/null @@ -1,319 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Device tree file for the Zyxel NSA 310S NAS box. - * - * Copyright (c) 2015-2021, Tony Dinh <mibodhi(a)gmail.com> - * - * Based on - * Copyright (c) 2014, Adam Baker <linux(a)baker-net.org.uk> - * Based upon the board setup file created by Peter Schildmann - */ -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - model = "Zyxel NSA310S"; - compatible = "zyxel,nsa320s", "marvell,kirkwood-88f6702", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x10000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &uart0; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pinctrl-names = "default"; - - pmx_sata0: pmx-sata0 { - marvell,pins ; - marvell,function = "sata0"; - }; - - pmx_sata1: pmx-sata1 { - marvell,pins ; - marvell,function = "sata1"; - }; - - pmx_usb_power: pmx-usb-power { - marvell,pins = "mpp21"; - marvell,function = "gpio"; - }; - - pmx_pwr_off: pmx-pwr-off { - marvell,pins = "mpp27"; - marvell,function = "gpio"; - }; - - pmx_btn_reset: pmx-btn-reset { - marvell,pins = "mpp24"; - marvell,function = "gpio"; - }; - - pmx_btn_copy: pmx-btn-copy { - marvell,pins = "mpp25"; - marvell,function = "gpio"; - }; - - pmx_btn_power: pmx-btn-power { - marvell,pins = "mpp26"; - marvell,function = "gpio"; - }; - - pmx_led_hdd2_green: pmx-led-hdd2-green { - marvell,pins = "mpp34"; - marvell,function = "gpio"; - }; - - pmx_led_hdd2_red: pmx-led-hdd2-red { - marvell,pins = "mpp12"; - marvell,function = "gpio"; - }; - - pmx_led_usb_green: pmx-led-usb-green { - marvell,pins = "mpp15"; - marvell,function = "gpio"; - }; - - pmx_led_copy_green: pmx-led-copy-green { - marvell,pins = "mpp22"; - marvell,function = "gpio"; - }; - - pmx_led_copy_red: pmx-led-copy-red { - marvell,pins = "mpp23"; - marvell,function = "gpio"; - }; - - pmx_led_sys_green: pmx-led-sys-green { - marvell,pins = "mpp28"; - marvell,function = "gpio"; - }; - - pmx_led_sys_orange: pmx-led-sys-orange { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - - pmx_led_hdd1_green: pmx-led-hdd1-green { - marvell,pins = "mpp16"; - marvell,function = "gpio"; - }; - - pmx_led_hdd1_red: pmx-led-hdd1-red { - marvell,pins = "mpp13"; - marvell,function = "gpio"; - }; - - pmx_pwr_sata1: pmx-pwr-sata1 { - marvell,pins = "mpp33"; - marvell,function = "gpio"; - }; - }; - - serial@12000 { - status = "ok"; - }; - - sata@80000 { - status = "okay"; - nr-ports = <1>; - }; - - rtc@10300 { - status = "disabled"; - }; - - i2c@11000 { - status = "okay"; - ht1382: rtc@68 { - compatible = "htk,ht1382"; - reg = <0x68>; - }; - }; - }; - - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pmx_usb_power &pmx_pwr_sata1>; - - usb0_power: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "USB Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; - enable-active-high; - gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>; - }; - - sata1_power: regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - regulator-name = "SATA1 Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; - enable-active-high; - gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; - }; - }; - - gpio_poweroff { - compatible = "gpio-poweroff"; - pinctrl-0 = <&pmx_pwr_off>; - pinctrl-names = "default"; - gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>; - }; - - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_btn_reset &pmx_btn_copy &pmx_btn_power>; - pinctrl-names = "default"; - - button@1 { - label = "Power Button"; - linux,code = <KEY_POWER>; - gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>; - }; - button@2 { - label = "Copy Button"; - linux,code = <KEY_COPY>; - gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; - }; - button@3 { - label = "Reset Button"; - linux,code = <KEY_RESTART>; - gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_led_hdd2_green &pmx_led_hdd2_red - &pmx_led_usb_green - &pmx_led_sys_green &pmx_led_sys_orange - &pmx_led_copy_green &pmx_led_copy_red - &pmx_led_hdd1_green &pmx_led_hdd1_red>; - pinctrl-names = "default"; - - green-sys { - label = "nsa310s:green:sys"; - gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "default-on"; - }; - orange-sys { - label = "nsa310s:orange:sys"; - gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; - }; - green-hdd1 { - label = "nsa310s:green:hdd1"; - gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; - }; - red-hdd1 { - label = "nsa310s:red:hdd1"; - gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; - }; - green-hdd2 { - label = "nsa310s:green:hdd2"; - gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; - }; - red-hdd2 { - label = "nsa310s:red:hdd2"; - gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; - }; - green-usb { - label = "nsa310s:green:usb"; - gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; - }; - green-copy { - label = "nsa310s:green:copy"; - gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "ide-disk"; - }; - red-copy { - label = "nsa310s:red:copy"; - gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&nand { - status = "okay"; - chip-delay = <35>; - - partition@0 { - label = "uboot"; - reg = <0x0000000 0x0100000>; - }; - partition@100000 { - label = "stock_uboot_env"; - reg = <0x0100000 0x0080000>; - }; - partition@180000 { - label = "key_store"; - reg = <0x0180000 0x0080000>; - }; - partition@200000 { - label = "info"; - reg = <0x0200000 0x0080000>; - }; - partition@280000 { - label = "etc"; - reg = <0x0280000 0x0a00000>; - }; - partition@c80000 { - label = "kernel_1"; - reg = <0x0c80000 0x0a00000>; - }; - partition@1680000 { - label = "rootfs1"; - reg = <0x1680000 0x2fc0000>; - }; - partition@4640000 { - label = "kernel_2"; - reg = <0x4640000 0x0a00000>; - }; - partition@5040000 { - label = "rootfs2"; - reg = <0x5040000 0x2fc0000>; - }; -}; - -&mdio { - status = "okay"; - ethphy0: ethernet-phy@1 { - compatible = "marvell,88e1510"; - reg = <1>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - phy-mode = "rgmii"; - }; -}; - -&pciec { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; diff --git a/arch/arm/dts/kirkwood-nsa325.dts b/arch/arm/dts/kirkwood-nsa325.dts deleted file mode 100644 index efc57cfa41..0000000000 --- a/arch/arm/dts/kirkwood-nsa325.dts +++ /dev/null @@ -1,231 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* Device tree file for the Zyxel NSA 325 NAS box. - * - * Copyright (c) 2015, Hans Ulli Kroll <ulli.kroll(a)googlemail.com> - * - * - * Based upon the board setup file created by Peter Schildmann - */ - -/dts-v1/; - -#include "kirkwood-nsa3x0-common.dtsi" - -/ { - model = "ZyXEL NSA325"; - compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x20000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &uart0; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pinctrl-names = "default"; - - pmx_led_hdd2_green: pmx-led-hdd2-green { - marvell,pins = "mpp12"; - marvell,function = "gpio"; - }; - - pmx_led_hdd2_red: pmx-led-hdd2-red { - marvell,pins = "mpp13"; - marvell,function = "gpio"; - }; - - pmx_mcu_data: pmx-mcu-data { - marvell,pins = "mpp14"; - marvell,function = "gpio"; - }; - - pmx_led_usb_green: pmx-led-usb-green { - marvell,pins = "mpp15"; - marvell,function = "gpio"; - }; - - pmx_mcu_clk: pmx-mcu-clk { - marvell,pins = "mpp16"; - marvell,function = "gpio"; - }; - - pmx_mcu_act: pmx-mcu-act { - marvell,pins = "mpp17"; - marvell,function = "gpio"; - }; - - pmx_led_sys_green: pmx-led-sys-green { - marvell,pins = "mpp28"; - marvell,function = "gpio"; - }; - - pmx_led_sys_orange: pmx-led-sys-orange { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - - pmx_led_hdd1_green: pmx-led-hdd1-green { - marvell,pins = "mpp41"; - marvell,function = "gpio"; - }; - - pmx_led_hdd1_red: pmx-led-hdd1-red { - marvell,pins = "mpp42"; - marvell,function = "gpio"; - }; - - pmx_htp: pmx-htp { - marvell,pins = "mpp43"; - marvell,function = "gpio"; - }; - - /* - * Buzzer needs to be switched at around 1kHz so is - * not compatible with the gpio-beeper driver. - */ - pmx_buzzer: pmx-buzzer { - marvell,pins = "mpp44"; - marvell,function = "gpio"; - }; - - pmx_vid_b1: pmx-vid-b1 { - marvell,pins = "mpp45"; - marvell,function = "gpio"; - }; - - pmx_power_resume_data: pmx-power-resume-data { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - - pmx_power_resume_clk: pmx-power-resume-clk { - marvell,pins = "mpp49"; - marvell,function = "gpio"; - }; - - pmx_pwr_sata1: pmx-pwr-sata1 { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - }; - - /* This board uses the pcf8563 RTC instead of the SoC RTC */ - rtc@10300 { - status = "disabled"; - }; - - i2c@11000 { - status = "okay"; - - pcf8563: pcf8563@51 { - compatible = "nxp,pcf8563"; - reg = <0x51>; - }; - }; - }; - - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_pwr_sata1>; - pinctrl-names = "default"; - - usb0_power: regulator@1 { - enable-active-high; - }; - - sata1_power: regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - regulator-name = "SATA1 Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; - enable-active-high; - gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_led_hdd2_green &pmx_led_hdd2_red - &pmx_led_usb_green - &pmx_led_sys_green &pmx_led_sys_orange - &pmx_led_copy_green &pmx_led_copy_red - &pmx_led_hdd1_green &pmx_led_hdd1_red>; - pinctrl-names = "default"; - - green-sys { - label = "nsa325:green:sys"; - gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; - }; - orange-sys { - label = "nsa325:orange:sys"; - gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; - }; - green-hdd1 { - label = "nsa325:green:hdd1"; - gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; - }; - red-hdd1 { - label = "nsa325:red:hdd1"; - gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; - }; - green-hdd2 { - label = "nsa325:green:hdd2"; - gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; - }; - red-hdd2 { - label = "nsa325:red:hdd2"; - gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; - }; - green-usb { - label = "nsa325:green:usb"; - gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; - }; - green-copy { - label = "nsa325:green:copy"; - gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; - }; - red-copy { - label = "nsa325:red:copy"; - gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; - }; - - /* The following pins are currently not assigned to a driver, - some of them should be configured as inputs. - pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act - &pmx_htp &pmx_vid_b1 - &pmx_power_resume_data &pmx_power_resume_clk>; */ - }; - -}; - -&mdio { - status = "okay"; - ethphy0: ethernet-phy@1 { - reg = <1>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; - -&pciec { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; diff --git a/arch/arm/dts/kirkwood-nsa3x0-common.dtsi b/arch/arm/dts/kirkwood-nsa3x0-common.dtsi deleted file mode 100644 index a21c50d44a..0000000000 --- a/arch/arm/dts/kirkwood-nsa3x0-common.dtsi +++ /dev/null @@ -1,157 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - model = "ZyXEL NSA310"; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - - pmx_usb_power: pmx-usb-power { - marvell,pins = "mpp21"; - marvell,function = "gpio"; - }; - - pmx_pwr_off: pmx-pwr-off { - marvell,pins = "mpp48"; - marvell,function = "gpio"; - }; - - pmx_btn_reset: pmx-btn-reset { - marvell,pins = "mpp36"; - marvell,function = "gpio"; - }; - - pmx_btn_copy: pmx-btn-copy { - marvell,pins = "mpp37"; - marvell,function = "gpio"; - }; - - pmx_btn_power: pmx-btn-power { - marvell,pins = "mpp46"; - marvell,function = "gpio"; - }; - - pmx_led_copy_green: pmx-led-copy-green { - marvell,pins = "mpp39"; - marvell,function = "gpio"; - }; - - pmx_led_copy_red: pmx-led-copy-red { - marvell,pins = "mpp40"; - marvell,function = "gpio"; - }; - }; - - serial@12000 { - status = "okay"; - }; - - sata@80000 { - status = "okay"; - nr-ports = <2>; - }; - }; - - gpio_poweroff { - compatible = "gpio-poweroff"; - pinctrl-0 = <&pmx_pwr_off>; - pinctrl-names = "default"; - gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; - }; - - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_btn_reset &pmx_btn_copy &pmx_btn_power>; - pinctrl-names = "default"; - - power { - label = "Power Button"; - linux,code = <KEY_POWER>; - gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>; - }; - copy { - label = "Copy Button"; - linux,code = <KEY_COPY>; - gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; - }; - reset { - label = "Reset Button"; - linux,code = <KEY_RESTART>; - gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; - }; - }; - - - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_usb_power>; - pinctrl-names = "default"; - - usb0_power: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "USB Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&nand { - status = "okay"; - chip-delay = <35>; - - partition@0 { - label = "uboot"; - reg = <0x0000000 0x0100000>; - }; - partition@100000 { - label = "uboot_env"; - reg = <0x0100000 0x0080000>; - }; - partition@180000 { - label = "key_store"; - reg = <0x0180000 0x0080000>; - }; - partition@200000 { - label = "info"; - reg = <0x0200000 0x0080000>; - }; - partition@280000 { - label = "etc"; - reg = <0x0280000 0x0a00000>; - }; - partition@c80000 { - label = "kernel_1"; - reg = <0x0c80000 0x0a00000>; - }; - partition@1680000 { - label = "rootfs1"; - reg = <0x1680000 0x2fc0000>; - }; - partition@4640000 { - label = "kernel_2"; - reg = <0x4640000 0x0a00000>; - }; - partition@5040000 { - label = "rootfs2"; - reg = <0x5040000 0x2fc0000>; - }; -}; - -&pciec { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; diff --git a/arch/arm/dts/kirkwood-openrd-base.dts b/arch/arm/dts/kirkwood-openrd-base.dts deleted file mode 100644 index 094191ece3..0000000000 --- a/arch/arm/dts/kirkwood-openrd-base.dts +++ /dev/null @@ -1,39 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Marvell OpenRD Base Board Description - * - * Andrew Lunn <andrew(a)lunn.ch> - * - * This file contains the definitions that are specific to OpenRD - * base variant of the Marvell Kirkwood Development Board. - */ - -/dts-v1/; - -#include "kirkwood-openrd.dtsi" - -/ { - model = "OpenRD Base"; - compatible = "marvell,openrd-base", "marvell,openrd", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - ocp@f1000000 { - serial@12100 { - status = "okay"; - }; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@8 { - reg = <8>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; diff --git a/arch/arm/dts/kirkwood-openrd-client.dts b/arch/arm/dts/kirkwood-openrd-client.dts deleted file mode 100644 index 74dc23daf6..0000000000 --- a/arch/arm/dts/kirkwood-openrd-client.dts +++ /dev/null @@ -1,73 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Marvell OpenRD Client Board Description - * - * Andrew Lunn <andrew(a)lunn.ch> - * - * This file contains the definitions that are specific to OpenRD - * client variant of the Marvell Kirkwood Development Board. - */ - -/dts-v1/; - -#include "kirkwood-openrd.dtsi" - -/ { - model = "OpenRD Client"; - compatible = "marvell,openrd-client", "marvell,openrd", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - ocp@f1000000 { - audio-controller@a0000 { - status = "okay"; - }; - i2c@11000 { - status = "okay"; - clock-frequency = <400000>; - - cs42l51: cs42l51@4a { - compatible = "cirrus,cs42l51"; - reg = <0x4a>; - #sound-dai-cells = <0>; - }; - }; - }; - - sound { - compatible = "simple-audio-card"; - simple-audio-card,format = "i2s"; - simple-audio-card,mclk-fs = <256>; - - simple-audio-card,cpu { - sound-dai = <&audio0 0>; - }; - - simple-audio-card,codec { - sound-dai = <&cs42l51>; - }; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@8 { - reg = <8>; - }; - ethphy1: ethernet-phy@24 { - reg = <24>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; - -&eth1 { - status = "okay"; - ethernet1-port@0 { - phy-handle = <&ethphy1>; - }; -}; diff --git a/arch/arm/dts/kirkwood-openrd-ultimate.dts b/arch/arm/dts/kirkwood-openrd-ultimate.dts deleted file mode 100644 index 888e13320c..0000000000 --- a/arch/arm/dts/kirkwood-openrd-ultimate.dts +++ /dev/null @@ -1,55 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Marvell OpenRD Ultimate Board Description - * - * Andrew Lunn <andrew(a)lunn.ch> - * - * This file contains the definitions that are specific to OpenRD - * ultimate variant of the Marvell Kirkwood Development Board. - */ - -/dts-v1/; - -#include "kirkwood-openrd.dtsi" - -/ { - model = "OpenRD Ultimate"; - compatible = "marvell,openrd-ultimate", "marvell,openrd", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - ocp@f1000000 { - i2c@11000 { - status = "okay"; - clock-frequency = <400000>; - - cs42l51: cs42l51@4a { - compatible = "cirrus,cs42l51"; - reg = <0x4a>; - }; - }; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@0 { - reg = <0>; - }; - ethphy1: ethernet-phy@1 { - reg = <1>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; - -&eth1 { - status = "okay"; - ethernet1-port@0 { - phy-handle = <&ethphy1>; - }; -}; diff --git a/arch/arm/dts/kirkwood-openrd.dtsi b/arch/arm/dts/kirkwood-openrd.dtsi deleted file mode 100644 index 47f03c69c5..0000000000 --- a/arch/arm/dts/kirkwood-openrd.dtsi +++ /dev/null @@ -1,122 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Marvell OpenRD (Base|Client|Ultimate) Board Description - * - * Andrew Lunn <andrew(a)lunn.ch> - * - * This file contains the definitions that are common between the three - * variants of the Marvell Kirkwood Development Board. - */ - -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - memory { - device_type = "memory"; - reg = <0x00000000 0x20000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8"; - stdout-path = &uart0; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pinctrl-0 = <&pmx_select28 &pmx_sdio_cd &pmx_select34>; - pinctrl-names = "default"; - - pmx_select28: pmx-select-rs232-rs485 { - marvell,pins = "mpp28"; - marvell,function = "gpio"; - }; - pmx_sdio_cd: pmx-sdio-cd { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - pmx_select34: pmx-select-uart-sd { - marvell,pins = "mpp34"; - marvell,function = "gpio"; - }; - }; - serial@12000 { - status = "okay"; - - }; - sata@80000 { - status = "okay"; - nr-ports = <2>; - }; - mvsdio@90000 { - status = "okay"; - cd-gpios = <&gpio0 29 9>; - }; - gpio@10100 { - p28 { - gpio-hog; - gpios = <28 GPIO_ACTIVE_HIGH>; - /* - * SelRS232or485 selects between RS-232 or RS-485 - * mode for the second UART. - * - * Low: RS-232 - * High: RS-485 - * - * To use the second UART, you need to change also - * the SelUARTorSD. - */ - output-low; - line-name = "SelRS232or485"; - }; - }; - gpio@10140 { - p2 { - gpio-hog; - gpios = <2 GPIO_ACTIVE_HIGH>; - /* - * SelUARTorSD selects between the second UART - * (serial@12100) and SD (mvsdio@90000). - * - * Low: UART - * High: SD - * - * When changing this line make sure the newly - * selected device node is enabled and the - * previously selected device node is disabled. - */ - output-high; /* Select SD by default */ - line-name = "SelUARTorSD"; - }; - }; - }; -}; - -&nand { - status = "okay"; - pinctrl-0 = <&pmx_nand>; - pinctrl-names = "default"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - }; - - partition@100000 { - label = "uImage"; - reg = <0x0100000 0x400000>; - }; - - partition@600000 { - label = "root"; - reg = <0x0600000 0x1FA00000>; - }; -}; - -&pciec { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; diff --git a/arch/arm/dts/kirkwood-pogo_e02.dts b/arch/arm/dts/kirkwood-pogo_e02.dts deleted file mode 100644 index f9e95e55f3..0000000000 --- a/arch/arm/dts/kirkwood-pogo_e02.dts +++ /dev/null @@ -1,132 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * kirkwood-pogo_e02.dts - Device tree file for Pogoplug E02 - * - * Copyright (C) 2015 Christoph Junghans <ottxor(a)gentoo.org> - * - * based on information of dts files from - * Arch Linux ARM by Oleg Rakhmanov <moonman.ca(a)gmail.com> - * OpenWrt by Felix Kaechele <heffer(a)fedoraproject.org> - * - */ - -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - model = "Cloud Engines Pogoplug E02"; - compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281", - "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x10000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8"; - stdout-path = &uart0; - }; - - gpio-leds { - compatible = "gpio-leds"; - - health { - label = "pogo_e02:green:health"; - gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - fault { - label = "pogo_e02:orange:fault"; - gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; - }; - }; - - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_usb_power_enable>; - pinctrl-names = "default"; - - usb_power: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "USB Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&pinctrl { - pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange - &pmx_led_green >; - pinctrl-names = "default"; - - pmx_usb_power_enable: pmx-usb-power-enable { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - - pmx_led_green: pmx-led-green { - marvell,pins = "mpp48"; - marvell,function = "gpio"; - }; - - pmx_led_orange: pmx-led-orange { - marvell,pins = "mpp49"; - marvell,function = "gpio"; - }; -}; - -&uart0 { - status = "okay"; -}; - -&nand { - chip-delay = <40>; - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - read-only; - }; - - partition@100000 { - label = "uImage"; - reg = <0x0100000 0x400000>; - }; - - partition@500000 { - label = "pogoplug"; - reg = <0x0500000 0x2000000>; - }; - - partition@2500000 { - label = "root"; - reg = <0x02500000 0x5b00000>; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@0 { - reg = <0>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; diff --git a/arch/arm/dts/kirkwood-pogoplug-series-4.dts b/arch/arm/dts/kirkwood-pogoplug-series-4.dts deleted file mode 100644 index 5aa4669ae2..0000000000 --- a/arch/arm/dts/kirkwood-pogoplug-series-4.dts +++ /dev/null @@ -1,180 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * kirkwood-pogoplug-series-4.dts - Device tree file for PogoPlug Series 4 - * inspired by the board files made by Kevin Mihelich for ArchLinux, - * and their DTS file. - * - * Copyright (C) 2015 Linus Walleij <linus.walleij(a)linaro.org> - */ - -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6192.dtsi" -#include <dt-bindings/input/linux-event-codes.h> - -/ { - model = "Cloud Engines PogoPlug Series 4"; - compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192", - "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x08000000>; - }; - - chosen { - stdout-path = "uart0:115200n8"; - }; - - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_button_eject>; - pinctrl-names = "default"; - - eject { - debounce-interval = <50>; - wakeup-source; - linux,code = <KEY_EJECTCD>; - label = "Eject Button"; - gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_led_green &pmx_led_red>; - pinctrl-names = "default"; - - health { - label = "pogoplugv4:green:health"; - gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; - default-state = "on"; - }; - fault { - label = "pogoplugv4:red:fault"; - gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&pinctrl { - pmx_sata0: pmx-sata0 { - marvell,pins = "mpp21"; - marvell,function = "sata0"; - }; - - pmx_sata1: pmx-sata1 { - marvell,pins = "mpp20"; - marvell,function = "sata1"; - }; - - pmx_sdio_cd: pmx-sdio-cd { - marvell,pins = "mpp27"; - marvell,function = "gpio"; - }; - - pmx_sdio_wp: pmx-sdio-wp { - marvell,pins = "mpp28"; - marvell,function = "gpio"; - }; - - pmx_button_eject: pmx-button-eject { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - - pmx_led_green: pmx-led-green { - marvell,pins = "mpp22"; - marvell,function = "gpio"; - }; - - pmx_led_red: pmx-led-red { - marvell,pins = "mpp24"; - marvell,function = "gpio"; - }; -}; - -&uart0 { - status = "okay"; -}; - -/* - * This PCIE controller has a USB 3.0 XHCI controller at 1,0 - */ -&pciec { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; - -&sata { - status = "okay"; - pinctrl-0 = <&pmx_sata0 &pmx_sata1>; - pinctrl-names = "default"; - nr-ports = <1>; -}; - -&sdio { - status = "okay"; - pinctrl-0 = <&pmx_sdio &pmx_sdio_cd &pmx_sdio_wp>; - pinctrl-names = "default"; - cd-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; - wp-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; -}; - -&nand { - /* 128 MiB of NAND flash */ - chip-delay = <40>; - status = "okay"; - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x00000000 0x200000>; - read-only; - }; - - partition@200000 { - label = "uImage"; - reg = <0x00200000 0x300000>; - }; - - partition@500000 { - label = "uImage2"; - reg = <0x00500000 0x300000>; - }; - - partition@800000 { - label = "failsafe"; - reg = <0x00800000 0x800000>; - }; - - partition@1000000 { - label = "root"; - reg = <0x01000000 0x7000000>; - }; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@0 { - reg = <0>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; diff --git a/arch/arm/dts/kirkwood-sheevaplug-common.dtsi b/arch/arm/dts/kirkwood-sheevaplug-common.dtsi deleted file mode 100644 index 0a698d3b73..0000000000 --- a/arch/arm/dts/kirkwood-sheevaplug-common.dtsi +++ /dev/null @@ -1,104 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * kirkwood-sheevaplug-common.dtsi - Common parts for Sheevaplugs - * - * Copyright (C) 2013 Simon Baatz <gmbnomis(a)gmail.com> - */ - -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - memory { - device_type = "memory"; - reg = <0x00000000 0x20000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk"; - stdout-path = &uart0; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - - pmx_usb_power_enable: pmx-usb-power-enable { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - pmx_led_red: pmx-led-red { - marvell,pins = "mpp46"; - marvell,function = "gpio"; - }; - pmx_led_blue: pmx-led-blue { - marvell,pins = "mpp49"; - marvell,function = "gpio"; - }; - pmx_sdio_cd: pmx-sdio-cd { - marvell,pins = "mpp44"; - marvell,function = "gpio"; - }; - pmx_sdio_wp: pmx-sdio-wp { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - }; - serial@12000 { - status = "okay"; - }; - }; - - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_usb_power_enable>; - pinctrl-names = "default"; - - usb_power: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "USB Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio0 29 0>; - }; - }; -}; - -&nand { - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - }; - - partition@100000 { - label = "uImage"; - reg = <0x0100000 0x400000>; - }; - - partition@500000 { - label = "root"; - reg = <0x0500000 0x1fb00000>; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@0 { - reg = <0>; - }; -}; - -&eth0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; diff --git a/arch/arm/dts/kirkwood-sheevaplug.dts b/arch/arm/dts/kirkwood-sheevaplug.dts deleted file mode 100644 index c73cc904e5..0000000000 --- a/arch/arm/dts/kirkwood-sheevaplug.dts +++ /dev/null @@ -1,42 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * kirkwood-sheevaplug.dts - Device tree file for Sheevaplug - * - * Copyright (C) 2013 Simon Baatz <gmbnomis(a)gmail.com> - */ - -/dts-v1/; - -#include "kirkwood-sheevaplug-common.dtsi" - -/ { - model = "Globalscale Technologies SheevaPlug"; - compatible = "globalscale,sheevaplug", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - ocp@f1000000 { - mvsdio@90000 { - pinctrl-0 = <&pmx_sdio>; - pinctrl-names = "default"; - status = "okay"; - /* No CD or WP GPIOs */ - broken-cd; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_led_blue &pmx_led_red>; - pinctrl-names = "default"; - - health { - label = "sheevaplug:blue:health"; - gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - - misc { - label = "sheevaplug:red:misc"; - gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; - }; - }; -}; diff --git a/arch/arm/dts/kirkwood-synology.dtsi b/arch/arm/dts/kirkwood-synology.dtsi deleted file mode 100644 index c97ed29a0a..0000000000 --- a/arch/arm/dts/kirkwood-synology.dtsi +++ /dev/null @@ -1,855 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Nodes for Marvell 628x Synology devices - * - * Andrew Lunn <andrew(a)lunn.ch> - * Ben Peddell <klightspeed(a)killerwolves.net> - * - */ - -/ { - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pmx_alarmled_12: pmx-alarmled-12 { - marvell,pins = "mpp12"; - marvell,function = "gpio"; - }; - - pmx_fanctrl_15: pmx-fanctrl-15 { - marvell,pins = "mpp15"; - marvell,function = "gpio"; - }; - - pmx_fanctrl_16: pmx-fanctrl-16 { - marvell,pins = "mpp16"; - marvell,function = "gpio"; - }; - - pmx_fanctrl_17: pmx-fanctrl-17 { - marvell,pins = "mpp17"; - marvell,function = "gpio"; - }; - - pmx_fanalarm_18: pmx-fanalarm-18 { - marvell,pins = "mpp18"; - marvell,function = "gpo"; - }; - - pmx_hddled_20: pmx-hddled-20 { - marvell,pins = "mpp20"; - marvell,function = "gpio"; - }; - - pmx_hddled_21: pmx-hddled-21 { - marvell,pins = "mpp21"; - marvell,function = "gpio"; - }; - - pmx_hddled_22: pmx-hddled-22 { - marvell,pins = "mpp22"; - marvell,function = "gpio"; - }; - - pmx_hddled_23: pmx-hddled-23 { - marvell,pins = "mpp23"; - marvell,function = "gpio"; - }; - - pmx_hddled_24: pmx-hddled-24 { - marvell,pins = "mpp24"; - marvell,function = "gpio"; - }; - - pmx_hddled_25: pmx-hddled-25 { - marvell,pins = "mpp25"; - marvell,function = "gpio"; - }; - - pmx_hddled_26: pmx-hddled-26 { - marvell,pins = "mpp26"; - marvell,function = "gpio"; - }; - - pmx_hddled_27: pmx-hddled-27 { - marvell,pins = "mpp27"; - marvell,function = "gpio"; - }; - - pmx_hddled_28: pmx-hddled-28 { - marvell,pins = "mpp28"; - marvell,function = "gpio"; - }; - - pmx_hdd1_pwr_29: pmx-hdd1-pwr-29 { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - - pmx_hdd1_pwr_30: pmx-hdd-pwr-30 { - marvell,pins = "mpp30"; - marvell,function = "gpio"; - }; - - pmx_hdd2_pwr_31: pmx-hdd2-pwr-31 { - marvell,pins = "mpp31"; - marvell,function = "gpio"; - }; - - pmx_fanctrl_32: pmx-fanctrl-32 { - marvell,pins = "mpp32"; - marvell,function = "gpio"; - }; - - pmx_fanctrl_33: pmx-fanctrl-33 { - marvell,pins = "mpp33"; - marvell,function = "gpo"; - }; - - pmx_fanctrl_34: pmx-fanctrl-34 { - marvell,pins = "mpp34"; - marvell,function = "gpio"; - }; - - pmx_hdd2_pwr_34: pmx-hdd2-pwr-34 { - marvell,pins = "mpp34"; - marvell,function = "gpio"; - }; - - pmx_fanalarm_35: pmx-fanalarm-35 { - marvell,pins = "mpp35"; - marvell,function = "gpio"; - }; - - pmx_hddled_36: pmx-hddled-36 { - marvell,pins = "mpp36"; - marvell,function = "gpio"; - }; - - pmx_hddled_37: pmx-hddled-37 { - marvell,pins = "mpp37"; - marvell,function = "gpio"; - }; - - pmx_hddled_38: pmx-hddled-38 { - marvell,pins = "mpp38"; - marvell,function = "gpio"; - }; - - pmx_hddled_39: pmx-hddled-39 { - marvell,pins = "mpp39"; - marvell,function = "gpio"; - }; - - pmx_hddled_40: pmx-hddled-40 { - marvell,pins = "mpp40"; - marvell,function = "gpio"; - }; - - pmx_hddled_41: pmx-hddled-41 { - marvell,pins = "mpp41"; - marvell,function = "gpio"; - }; - - pmx_hddled_42: pmx-hddled-42 { - marvell,pins = "mpp42"; - marvell,function = "gpio"; - }; - - pmx_hddled_43: pmx-hddled-43 { - marvell,pins = "mpp43"; - marvell,function = "gpio"; - }; - - pmx_hddled_44: pmx-hddled-44 { - marvell,pins = "mpp44"; - marvell,function = "gpio"; - }; - - pmx_hddled_45: pmx-hddled-45 { - marvell,pins = "mpp45"; - marvell,function = "gpio"; - }; - - pmx_hdd3_pwr_44: pmx-hdd3-pwr-44 { - marvell,pins = "mpp44"; - marvell,function = "gpio"; - }; - - pmx_hdd4_pwr_45: pmx-hdd4-pwr-45 { - marvell,pins = "mpp45"; - marvell,function = "gpio"; - }; - - pmx_fanalarm_44: pmx-fanalarm-44 { - marvell,pins = "mpp44"; - marvell,function = "gpio"; - }; - - pmx_fanalarm_45: pmx-fanalarm-45 { - marvell,pins = "mpp45"; - marvell,function = "gpio"; - }; - }; - - rtc@10300 { - status = "disabled"; - }; - - spi@10600 { - status = "okay"; - - m25p80@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,m25p80", "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <20000000>; - mode = <0>; - - partition@0 { - reg = <0x00000000 0x00080000>; - label = "RedBoot"; - }; - - partition@80000 { - reg = <0x00080000 0x00200000>; - label = "zImage"; - }; - - partition@280000 { - reg = <0x00280000 0x00140000>; - label = "rd.gz"; - }; - - partition@3c0000 { - reg = <0x003c0000 0x00010000>; - label = "vendor"; - }; - - partition@3d0000 { - reg = <0x003d0000 0x00020000>; - label = "RedBoot config"; - }; - - partition@3f0000 { - reg = <0x003f0000 0x00010000>; - label = "FIS directory"; - }; - }; - }; - - i2c@11000 { - status = "okay"; - clock-frequency = <400000>; - - rs5c372: rs5c372@32 { - status = "disabled"; - compatible = "ricoh,rs5c372"; - reg = <0x32>; - }; - - s35390a: s35390a@30 { - status = "disabled"; - compatible = "sii,s35390a"; - reg = <0x30>; - }; - }; - - serial@12000 { - status = "okay"; - }; - - serial@12100 { - status = "okay"; - }; - - poweroff@12100 { - compatible = "synology,power-off"; - reg = <0x12100 0x100>; - clocks = <&gate_clk 7>; - }; - - sata@80000 { - pinctrl-0 = <&pmx_sata0 &pmx_sata1>; - pinctrl-names = "default"; - status = "okay"; - nr-ports = <2>; - }; - }; - - gpio-fan-150-32-35 { - status = "disabled"; - compatible = "gpio-fan"; - pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34 - &pmx_fanalarm_35>; - pinctrl-names = "default"; - gpios = <&gpio1 0 GPIO_ACTIVE_HIGH - &gpio1 1 GPIO_ACTIVE_HIGH - &gpio1 2 GPIO_ACTIVE_HIGH>; - gpio-fan,speed-map = < 0 0 - 2200 1 - 2500 2 - 3000 4 - 3300 3 - 3700 5 - 3800 6 - 4200 7 >; - }; - - gpio-fan-150-15-18 { - status = "disabled"; - compatible = "gpio-fan"; - pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 - &pmx_fanalarm_18>; - pinctrl-names = "default"; - gpios = <&gpio0 15 GPIO_ACTIVE_HIGH - &gpio0 16 GPIO_ACTIVE_HIGH - &gpio0 17 GPIO_ACTIVE_HIGH>; - alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; - gpio-fan,speed-map = < 0 0 - 2200 1 - 2500 2 - 3000 4 - 3300 3 - 3700 5 - 3800 6 - 4200 7 >; - }; - - gpio-fan-100-32-35 { - status = "disabled"; - compatible = "gpio-fan"; - pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34 - &pmx_fanalarm_35>; - pinctrl-names = "default"; - gpios = <&gpio1 0 GPIO_ACTIVE_HIGH - &gpio1 1 GPIO_ACTIVE_HIGH - &gpio1 2 GPIO_ACTIVE_HIGH>; - alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; - gpio-fan,speed-map = < 0 0 - 2500 1 - 3100 2 - 3800 3 - 4600 4 - 4800 5 - 4900 6 - 5000 7 >; - }; - - gpio-fan-100-15-18 { - status = "disabled"; - compatible = "gpio-fan"; - pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 - &pmx_fanalarm_18>; - pinctrl-names = "default"; - gpios = <&gpio0 15 GPIO_ACTIVE_HIGH - &gpio0 16 GPIO_ACTIVE_HIGH - &gpio0 17 GPIO_ACTIVE_HIGH>; - alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; - gpio-fan,speed-map = < 0 0 - 2500 1 - 3100 2 - 3800 3 - 4600 4 - 4800 5 - 4900 6 - 5000 7 >; - }; - - gpio-fan-100-15-35-1 { - status = "disabled"; - compatible = "gpio-fan"; - pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 - &pmx_fanalarm_35>; - pinctrl-names = "default"; - gpios = <&gpio0 15 GPIO_ACTIVE_HIGH - &gpio0 16 GPIO_ACTIVE_HIGH - &gpio0 17 GPIO_ACTIVE_HIGH>; - alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; - gpio-fan,speed-map = < 0 0 - 2500 1 - 3100 2 - 3800 3 - 4600 4 - 4800 5 - 4900 6 - 5000 7 >; - }; - - gpio-fan-100-15-35-3 { - status = "disabled"; - compatible = "gpio-fan"; - pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 - &pmx_fanalarm_35 &pmx_fanalarm_44 &pmx_fanalarm_45>; - pinctrl-names = "default"; - gpios = <&gpio0 15 GPIO_ACTIVE_HIGH - &gpio0 16 GPIO_ACTIVE_HIGH - &gpio0 17 GPIO_ACTIVE_HIGH>; - alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH - &gpio1 12 GPIO_ACTIVE_HIGH - &gpio1 13 GPIO_ACTIVE_HIGH>; - gpio-fan,speed-map = < 0 0 - 2500 1 - 3100 2 - 3800 3 - 4600 4 - 4800 5 - 4900 6 - 5000 7 >; - }; - - gpio-leds-alarm-12 { - status = "disabled"; - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_alarmled_12>; - pinctrl-names = "default"; - - hdd1-green { - label = "synology:alarm"; - gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-leds-hdd-20 { - status = "disabled"; - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_hddled_20 &pmx_hddled_21 &pmx_hddled_22 - &pmx_hddled_23 &pmx_hddled_24 &pmx_hddled_25 - &pmx_hddled_26 &pmx_hddled_27>; - pinctrl-names = "default"; - - hdd1-green { - label = "synology:green:hdd1"; - gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; - }; - - hdd1-amber { - label = "synology:amber:hdd1"; - gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; - }; - - hdd2-green { - label = "synology:green:hdd2"; - gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; - }; - - hdd2-amber { - label = "synology:amber:hdd2"; - gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; - }; - - hdd3-green { - label = "synology:green:hdd3"; - gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; - }; - - hdd3-amber { - label = "synology:amber:hdd3"; - gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; - }; - - hdd4-green { - label = "synology:green:hdd4"; - gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; - }; - - hdd4-amber { - label = "synology:amber:hdd4"; - gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-leds-hdd-21-1 { - status = "disabled"; - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23>; - pinctrl-names = "default"; - - hdd1-green { - label = "synology:green:hdd1"; - gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; - }; - - hdd1-amber { - label = "synology:amber:hdd1"; - gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-leds-hdd-21-2 { - status = "disabled"; - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23 &pmx_hddled_20 &pmx_hddled_22>; - pinctrl-names = "default"; - - hdd1-green { - label = "synology:green:hdd1"; - gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; - }; - - hdd1-amber { - label = "synology:amber:hdd1"; - gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; - }; - - hdd2-green { - label = "synology:green:hdd2"; - gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; - }; - - hdd2-amber { - label = "synology:amber:hdd2"; - gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-leds-hdd-36 { - status = "disabled"; - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_hddled_36 &pmx_hddled_37 &pmx_hddled_38 - &pmx_hddled_39 &pmx_hddled_40 &pmx_hddled_41 - &pmx_hddled_42 &pmx_hddled_43 &pmx_hddled_44 - &pmx_hddled_45>; - pinctrl-names = "default"; - - hdd1-green { - label = "synology:green:hdd1"; - gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; - }; - - hdd1-amber { - label = "synology:amber:hdd1"; - gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; - }; - - hdd2-green { - label = "synology:green:hdd2"; - gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; - }; - - hdd2-amber { - label = "synology:amber:hdd2"; - gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; - }; - - hdd3-green { - label = "synology:green:hdd3"; - gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; - }; - - hdd3-amber { - label = "synology:amber:hdd3"; - gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; - }; - - hdd4-green { - label = "synology:green:hdd4"; - gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; - }; - - hdd4-amber { - label = "synology:amber:hdd4"; - gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; - }; - - hdd5-green { - label = "synology:green:hdd5"; - gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; - }; - - hdd5-amber { - label = "synology:amber:hdd5"; - gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-leds-hdd-38 { - status = "disabled"; - compatible = "gpio-leds"; - pinctrl-0 = <&pmx_hddled_38 &pmx_hddled_39 &pmx_hddled_36 &pmx_hddled_37>; - pinctrl-names = "default"; - - hdd1-green { - label = "synology:green:hdd1"; - gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; - }; - - hdd1-amber { - label = "synology:amber:hdd1"; - gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; - }; - - hdd2-green { - label = "synology:green:hdd2"; - gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; - }; - - hdd2-amber { - label = "synology:amber:hdd2"; - gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; - }; - }; - - regulators-hdd-29 { - status = "disabled"; - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_hdd1_pwr_29 &pmx_hdd2_pwr_31>; - pinctrl-names = "default"; - - regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "hdd1power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - startup-delay-us = <5000000>; - gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; - }; - - regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - regulator-name = "hdd2power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - startup-delay-us = <5000000>; - gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>; - }; - }; - - regulators-hdd-30-1 { - status = "disabled"; - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_hdd1_pwr_30>; - pinctrl-names = "default"; - - regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "hdd1power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - startup-delay-us = <5000000>; - gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; - }; - }; - - regulators-hdd-30-2 { - status = "disabled"; - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34>; - pinctrl-names = "default"; - - regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "hdd1power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - startup-delay-us = <5000000>; - gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; - }; - - regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - regulator-name = "hdd2power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - startup-delay-us = <5000000>; - gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; - }; - }; - - regulators-hdd-30-4 { - status = "disabled"; - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34 - &pmx_hdd3_pwr_44 &pmx_hdd4_pwr_45>; - pinctrl-names = "default"; - - regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "hdd1power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - startup-delay-us = <5000000>; - gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; - }; - - regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - regulator-name = "hdd2power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - startup-delay-us = <5000000>; - gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; - }; - - regulator@3 { - compatible = "regulator-fixed"; - reg = <3>; - regulator-name = "hdd3power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - startup-delay-us = <5000000>; - gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; - }; - - regulator@4 { - compatible = "regulator-fixed"; - reg = <4>; - regulator-name = "hdd4power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - startup-delay-us = <5000000>; - gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; - }; - }; - - regulators-hdd-31 { - status = "disabled"; - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_hdd2_pwr_31>; - pinctrl-names = "default"; - - regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "hdd2power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - startup-delay-us = <5000000>; - gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>; - }; - }; - - regulators-hdd-34 { - status = "disabled"; - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_hdd2_pwr_34 &pmx_hdd3_pwr_44 - &pmx_hdd4_pwr_45>; - pinctrl-names = "default"; - - regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - regulator-name = "hdd2power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - startup-delay-us = <5000000>; - gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; - }; - - regulator@3 { - compatible = "regulator-fixed"; - reg = <3>; - regulator-name = "hdd3power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - startup-delay-us = <5000000>; - gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; - }; - - regulator@4 { - compatible = "regulator-fixed"; - reg = <4>; - regulator-name = "hdd4power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - startup-delay-us = <5000000>; - gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@0 { - device_type = "ethernet-phy"; - reg = <8>; - }; - - ethphy1: ethernet-phy@1 { - device_type = "ethernet-phy"; - reg = <9>; - }; -}; - -&eth0 { - status = "okay"; - - ethernet0-port@0 { - phy-handle = <&ethphy0>; - }; -}; - -&eth1 { - status = "disabled"; - - ethernet1-port@0 { - phy-handle = <&ethphy1>; - }; -}; - -&pciec { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; diff --git a/arch/arm/dts/kirkwood.dtsi b/arch/arm/dts/kirkwood.dtsi deleted file mode 100644 index 81c7eda2c4..0000000000 --- a/arch/arm/dts/kirkwood.dtsi +++ /dev/null @@ -1,393 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/include/ "skeleton.dtsi" -#include <dt-bindings/input/input.h> -#include <dt-bindings/gpio/gpio.h> - -#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) - -/ { - compatible = "marvell,kirkwood"; - interrupt-parent = <&intc>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - cpu@0 { - device_type = "cpu"; - compatible = "marvell,feroceon"; - reg = <0>; - clocks = <&core_clk 1>, <&core_clk 3>, <&gate_clk 11>; - clock-names = "cpu_clk", "ddrclk", "powersave"; - }; - }; - - aliases { - gpio0 = &gpio0; - gpio1 = &gpio1; - i2c0 = &i2c0; - }; - - mbus@f1000000 { - compatible = "marvell,kirkwood-mbus", "simple-bus"; - #address-cells = <2>; - #size-cells = <1>; - /* If a board file needs to change this ranges it must replace it completely */ - ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */ - MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */ - MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */ - >; - controller = <&mbusc>; - pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256 MiB memory space */ - pcie-io-aperture = <0xf2000000 0x100000>; /* 1 MiB I/O space */ - - nand: nand@12f { - #address-cells = <1>; - #size-cells = <1>; - cle = <0>; - ale = <1>; - bank-width = <1>; - compatible = "marvell,orion-nand"; - reg = <MBUS_ID(0x01, 0x2f) 0 0x400>; - chip-delay = <25>; - /* set partition map and/or chip-delay in board dts */ - clocks = <&gate_clk 7>; - pinctrl-0 = <&pmx_nand>; - pinctrl-names = "default"; - status = "disabled"; - }; - - crypto_sram: sa-sram@301 { - compatible = "mmio-sram"; - reg = <MBUS_ID(0x03, 0x01) 0x0 0x800>; - clocks = <&gate_clk 17>; - #address-cells = <1>; - #size-cells = <1>; - }; - }; - - ocp@f1000000 { - compatible = "simple-bus"; - ranges = <0x00000000 0xf1000000 0x0100000>; - #address-cells = <1>; - #size-cells = <1>; - - pinctrl: pin-controller@10000 { - /* set compatible property in SoC file */ - reg = <0x10000 0x20>; - - pmx_ge1: pmx-ge1 { - marvell,pins = "mpp20", "mpp21", "mpp22", "mpp23", - "mpp24", "mpp25", "mpp26", "mpp27", - "mpp30", "mpp31", "mpp32", "mpp33"; - marvell,function = "ge1"; - }; - - pmx_nand: pmx-nand { - marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3", - "mpp4", "mpp5", "mpp18", "mpp19"; - marvell,function = "nand"; - }; - - /* - * Default SPI0 pinctrl setting with CSn on mpp0, - * overwrite marvell,pins on board level if required. - */ - pmx_spi: pmx-spi { - marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3"; - marvell,function = "spi"; - }; - - pmx_twsi0: pmx-twsi0 { - marvell,pins = "mpp8", "mpp9"; - marvell,function = "twsi0"; - }; - - /* - * Default UART pinctrl setting without RTS/CTS, - * overwrite marvell,pins on board level if required. - */ - pmx_uart0: pmx-uart0 { - marvell,pins = "mpp10", "mpp11"; - marvell,function = "uart0"; - }; - - pmx_uart1: pmx-uart1 { - marvell,pins = "mpp13", "mpp14"; - marvell,function = "uart1"; - }; - }; - - core_clk: core-clocks@10030 { - compatible = "marvell,kirkwood-core-clock"; - reg = <0x10030 0x4>; - #clock-cells = <1>; - }; - - spi0: spi@10600 { - compatible = "marvell,orion-spi"; - #address-cells = <1>; - #size-cells = <0>; - cell-index = <0>; - interrupts = <23>; - reg = <0x10600 0x28>; - clocks = <&gate_clk 7>; - pinctrl-0 = <&pmx_spi>; - pinctrl-names = "default"; - status = "disabled"; - }; - - gpio0: gpio@10100 { - compatible = "marvell,orion-gpio"; - #gpio-cells = <2>; - gpio-controller; - reg = <0x10100 0x40>; - ngpios = <32>; - interrupt-controller; - #interrupt-cells = <2>; - interrupts = <35>, <36>, <37>, <38>; - clocks = <&gate_clk 7>; - }; - - gpio1: gpio@10140 { - compatible = "marvell,orion-gpio"; - #gpio-cells = <2>; - gpio-controller; - reg = <0x10140 0x40>; - ngpios = <18>; - interrupt-controller; - #interrupt-cells = <2>; - interrupts = <39>, <40>, <41>; - clocks = <&gate_clk 7>; - }; - - i2c0: i2c@11000 { - compatible = "marvell,mv64xxx-i2c"; - reg = <0x11000 0x20>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <29>; - clock-frequency = <100000>; - clocks = <&gate_clk 7>; - pinctrl-0 = <&pmx_twsi0>; - pinctrl-names = "default"; - status = "disabled"; - }; - - uart0: serial@12000 { - compatible = "ns16550a"; - reg = <0x12000 0x100>; - reg-shift = <2>; - interrupts = <33>; - clocks = <&gate_clk 7>; - pinctrl-0 = <&pmx_uart0>; - pinctrl-names = "default"; - status = "disabled"; - }; - - uart1: serial@12100 { - compatible = "ns16550a"; - reg = <0x12100 0x100>; - reg-shift = <2>; - interrupts = <34>; - clocks = <&gate_clk 7>; - pinctrl-0 = <&pmx_uart1>; - pinctrl-names = "default"; - status = "disabled"; - }; - - mbusc: mbus-controller@20000 { - compatible = "marvell,mbus-controller"; - reg = <0x20000 0x80>, <0x1500 0x20>; - }; - - sysc: system-controller@20000 { - compatible = "marvell,orion-system-controller"; - reg = <0x20000 0x120>; - }; - - bridge_intc: bridge-interrupt-ctrl@20110 { - compatible = "marvell,orion-bridge-intc"; - interrupt-controller; - #interrupt-cells = <1>; - reg = <0x20110 0x8>; - interrupts = <1>; - marvell,#interrupts = <6>; - }; - - gate_clk: clock-gating-control@2011c { - compatible = "marvell,kirkwood-gating-clock"; - reg = <0x2011c 0x4>; - clocks = <&core_clk 0>; - #clock-cells = <1>; - }; - - l2: l2-cache@20128 { - compatible = "marvell,kirkwood-cache"; - reg = <0x20128 0x4>; - }; - - intc: main-interrupt-ctrl@20200 { - compatible = "marvell,orion-intc"; - interrupt-controller; - #interrupt-cells = <1>; - reg = <0x20200 0x10>, <0x20210 0x10>; - }; - - timer: timer@20300 { - compatible = "marvell,orion-timer"; - reg = <0x20300 0x20>; - interrupt-parent = <&bridge_intc>; - interrupts = <1>, <2>; - clocks = <&core_clk 0>; - }; - - wdt: watchdog-timer@20300 { - compatible = "marvell,orion-wdt"; - reg = <0x20300 0x28>, <0x20108 0x4>; - interrupt-parent = <&bridge_intc>; - interrupts = <3>; - clocks = <&gate_clk 7>; - status = "okay"; - }; - - cesa: crypto@30000 { - compatible = "marvell,kirkwood-crypto"; - reg = <0x30000 0x10000>; - reg-names = "regs"; - interrupts = <22>; - clocks = <&gate_clk 17>; - marvell,crypto-srams = <&crypto_sram>; - marvell,crypto-sram-size = <0x800>; - status = "okay"; - }; - - usb0: ehci@50000 { - compatible = "marvell,orion-ehci"; - reg = <0x50000 0x1000>; - interrupts = <19>; - clocks = <&gate_clk 3>; - status = "okay"; - }; - - dma0: xor@60800 { - compatible = "marvell,orion-xor"; - reg = <0x60800 0x100 - 0x60A00 0x100>; - status = "okay"; - clocks = <&gate_clk 8>; - - xor00 { - interrupts = <5>; - dmacap,memcpy; - dmacap,xor; - }; - xor01 { - interrupts = <6>; - dmacap,memcpy; - dmacap,xor; - dmacap,memset; - }; - }; - - dma1: xor@60900 { - compatible = "marvell,orion-xor"; - reg = <0x60900 0x100 - 0x60B00 0x100>; - status = "okay"; - clocks = <&gate_clk 16>; - - xor00 { - interrupts = <7>; - dmacap,memcpy; - dmacap,xor; - }; - xor01 { - interrupts = <8>; - dmacap,memcpy; - dmacap,xor; - dmacap,memset; - }; - }; - - eth0: ethernet-controller@72000 { - compatible = "marvell,kirkwood-eth"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x72000 0x4000>; - clocks = <&gate_clk 0>; - marvell,tx-checksum-limit = <1600>; - status = "disabled"; - - eth0port: ethernet0-port@0 { - compatible = "marvell,kirkwood-eth-port"; - reg = <0>; - interrupts = <11>; - /* overwrite MAC address in bootloader */ - local-mac-address = [00 00 00 00 00 00]; - /* set phy-handle property in board file */ - }; - }; - - mdio: mdio-bus@72004 { - compatible = "marvell,orion-mdio"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x72004 0x84>; - interrupts = <46>; - clocks = <&gate_clk 0>; - status = "disabled"; - - /* add phy nodes in board file */ - }; - - eth1: ethernet-controller@76000 { - compatible = "marvell,kirkwood-eth"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x76000 0x4000>; - clocks = <&gate_clk 19>; - marvell,tx-checksum-limit = <1600>; - pinctrl-0 = <&pmx_ge1>; - pinctrl-names = "default"; - status = "disabled"; - - eth1port: ethernet1-port@0 { - compatible = "marvell,kirkwood-eth-port"; - reg = <0>; - interrupts = <15>; - /* overwrite MAC address in bootloader */ - local-mac-address = [00 00 00 00 00 00]; - /* set phy-handle property in board file */ - }; - }; - - sata_phy0: sata-phy@82000 { - compatible = "marvell,mvebu-sata-phy"; - reg = <0x82000 0x0334>; - clocks = <&gate_clk 14>; - clock-names = "sata"; - #phy-cells = <0>; - status = "ok"; - }; - - sata_phy1: sata-phy@84000 { - compatible = "marvell,mvebu-sata-phy"; - reg = <0x84000 0x0334>; - clocks = <&gate_clk 15>; - clock-names = "sata"; - #phy-cells = <0>; - status = "ok"; - }; - - audio0: audio-controller@a0000 { - compatible = "marvell,kirkwood-audio"; - #sound-dai-cells = <0>; - reg = <0xa0000 0x2210>; - interrupts = <24>; - clocks = <&gate_clk 9>; - clock-names = "internal"; - status = "disabled"; - }; - }; -}; -- 2.39.2

3 3

[PATCH u-boot-mvebu v4 00/18] Turris Omnia - New board revision support
by Marek Behún 04 Apr '24

04 Apr '24

changes since v3: - added missing files turris_common.c and turris_common.h to patch 05/18 - added comment to patch 11/18 before while (1); as discussed in v3 v1, v2 and v3 at: https://patchwork.ozlabs.org/project/uboot/cover/20240304152148.3847-1-kabe… https://patchwork.ozlabs.org/project/uboot/cover/20240323180711.5498-1-kabe… https://patchwork.ozlabs.org/project/uboot/cover/20240327162355.24584-1-kab… Marek Behún (18): arm: mvebu: turris_omnia: Enable LTO by default on Turris Omnia arm: mvebu: turris_omnia: Add header containing MCU command interface and use it arm: mvebu: turris_{omnia, mox}: Don't print model two times arm: mvebu: turris_omnia: Update MCU status and features reading arm: mvebu: turris_omnia: Implement getting board information from MCU arm: mvebu: turris_omnia: Print board ECDSA public key if available arm: mvebu: turris_omnia: Disable Atmel SHA node if not present arm: mvebu: spl: Do not build mvebu-reset in SPL arm: mvebu: system-controller: Rework to use UCLASS_SYSCON arm: mvebu: system-controller: Select mvebu-reset if DM_RESET && PCI_MVEBU arm: mvebu: system-controller: Add support for SYSRESET gpio: turris_omnia_mcu: Use byteorder conversion functions gpio: turris_omnia_mcu: Update firmware features reading gpio: turris_omnia_mcu: Add support for system power off via sysreset arm: mvebu: turris_omnia: Enable poweroff command via sysreset in defconfig cmd: rng: Print "Abort" on -EINTR misc: turris_omnia_mcu: Add support for rng provided by MCU arm: mvebu: turris_omnia: Enable rng command in defconfig arch/arm/mach-mvebu/Kconfig | 25 ++ arch/arm/mach-mvebu/Makefile | 3 +- arch/arm/mach-mvebu/cpu.c | 2 + arch/arm/mach-mvebu/system-controller.c | 145 ++++++-- board/CZ.NIC/turris_atsha_otp.c | 27 +- board/CZ.NIC/turris_common.c | 42 +++ board/CZ.NIC/turris_common.h | 10 + board/CZ.NIC/turris_mox/turris_mox.c | 5 +- board/CZ.NIC/turris_omnia/Makefile | 2 +- board/CZ.NIC/turris_omnia/turris_omnia.c | 310 ++++++++++++----- cmd/rng.c | 7 +- configs/turris_omnia_defconfig | 6 + drivers/gpio/Kconfig | 7 - drivers/gpio/Makefile | 1 - drivers/gpio/turris_omnia_mcu.c | 316 ----------------- drivers/misc/Kconfig | 11 + drivers/misc/Makefile | 1 + drivers/misc/turris_omnia_mcu.c | 411 +++++++++++++++++++++++ include/turris-omnia-mcu-interface.h | 248 ++++++++++++++ 19 files changed, 1097 insertions(+), 482 deletions(-) create mode 100644 board/CZ.NIC/turris_common.c create mode 100644 board/CZ.NIC/turris_common.h delete mode 100644 drivers/gpio/turris_omnia_mcu.c create mode 100644 drivers/misc/turris_omnia_mcu.c create mode 100644 include/turris-omnia-mcu-interface.h -- 2.43.2

2 19

[PATCH v1] MAINTAINERS: add entries for tee-related orphaned files
by Igor Opaniuk 04 Apr '24

04 Apr '24

Add orphaned TEE/OP-TEE-related files to TEE subsystem entry in MAINTAINERS. This includes: - optee_rpmb cmd and test for it - Misc. OP-TEE tests - OP-TEE SCMI agent implementation - Documentation, including device tree bindings Signed-off-by: Igor Opaniuk <igor.opaniuk(a)gmail.com> --- MAINTAINERS | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index 0462ade4ac6..0f7325d6045 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1642,9 +1642,18 @@ M: Jens Wiklander <jens.wiklander(a)linaro.org> M: Ilias Apalodimas <ilias.apalodimas(a)linaro.org> T: git https://source.denx.de/u-boot/custodians/u-boot-tpm.git S: Maintained +F: cmd/optee* +F: doc/README.tee +F: doc/device-tree-bindings/firmware/linaro,optee-tz.txt +F: drivers/firmware/scmi/optee_agent.c F: drivers/tee/ +F: include/sandboxtee.h F: include/tee.h F: include/tee/ +F: include/test/optee.h +F: test/dm/tee.c +F: test/optee/ +F: test/py/tests/test_optee_rpmb.py TEE-lib M: Bryan O'Donoghue <bryan.odonoghue(a)linaro.org> -- 2.34.1

3 2

[PATCH v4 0/5] TEE: minor cleanup
by Igor Opaniuk 04 Apr '24

04 Apr '24

- Address some spelling errors and typos - Support CMD_OPTEE_RPMB for SANDBOX configurations and add python tests - Remove common.h inclusion for drivers/tee - Add calls for closing tee session after every read/write operation. CI build: [1] https://dev.azure.com/igoropaniuk/u-boot/_build/results?buildId=31&view=res… Changes in v4: - Rebased on the latest master and excluded "tee: sandbox: fix spelling errors", as it was merged already by Heinrich Schuchardt Changes in v3: - Added calls for closing tee session after every read/write operation Changes in v2: - Fixed chimp_optee.c:37:9: error: implicit declaration of function 'memset' - Applied R-b and T-b tags Igor Opaniuk (5): tee: optee: fix description in Kconfig cmd: optee_rpmb: close tee session cmd: optee_rpmb: build cmd for sandbox test: py: add optee_rpmb tests tee: remove common.h inclusion cmd/Kconfig | 4 +++- cmd/optee_rpmb.c | 23 +++++++++++++++++------ drivers/tee/broadcom/chimp_optee.c | 3 ++- drivers/tee/optee/Kconfig | 2 +- drivers/tee/optee/core.c | 1 - drivers/tee/optee/i2c.c | 1 - drivers/tee/optee/rpmb.c | 1 - drivers/tee/optee/supplicant.c | 2 +- drivers/tee/sandbox.c | 2 +- drivers/tee/tee-uclass.c | 1 - test/py/tests/test_optee_rpmb.py | 20 ++++++++++++++++++++ 11 files changed, 45 insertions(+), 15 deletions(-) create mode 100644 test/py/tests/test_optee_rpmb.py -- 2.34.1

2 15