September 2023 - U-Boot

USB: error messages on DWC3 gadget endpoint dequeue
by João Paulo Silva Gonçalves 15 Sep '23

15 Sep '23

Hi Marek, I was testing fastboot image download over usb for imx8mp (from usb recovery patch of verdin-imx8mp) and i am having error messages on endpoint request dequeue function of DWC3 gadget controller. However, download is working fine, so this message may not be an error. They are happening because fastboot tx before sending a new usb request dequeue the same request, maybe to be sure it does not send it twice. Can I just ignore these messages? Maybe change its log level to dbg instead of error? What do you think? The messages I am seeing are below and are the ones with "... was not queued to ep1in-bulk". U-Boot 2023.10-rc3-00028-gc99d052c76 (Sep 14 2023 - 15:59:22 -0300) CPU: Freescale i.MX8MP[8] rev1.1 1600 MHz (running at 1200 MHz) CPU: Industrial temperature grade (-40C to 105C) at 47C Reset cause: POR DRAM: 4 GiB Core: 168 devices, 28 uclasses, devicetree: separate WDT: Started watchdog@30280000 with servicing every 1000ms (60s timeout) MMC: FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@30880000 Out: serial@30880000 Err: serial@30880000 Model: Toradex 0058 Verdin iMX8M Plus Quad 4GB WB IT V1.1A Serial#: 15007098 Carrier: Toradex Dahlia V1.1C, Serial# 10952631 SEC0: RNG instantiated Net: eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME] Hit any key to stop autoboot: 0 Verdin iMX8MP # Verdin iMX8MP # fastboot 0 dwc3-generic-peripheral usb@38100000: request 00000000ffb29c40 was not queued to ep1in-bulk Starting download of 3084 bytes dwc3-generic-peripheral usb@38100000: request 00000000ffb29c40 was not queued to ep1in-bulk downloading of 3084 bytes finished dwc3-generic-peripheral usb@38100000: request 00000000ffb29c40 was not queued to ep1in-bulk dwc3-generic-peripheral usb@38100000: request 00000000ffb29c40 was not queued to ep1in-bulk Starting download of 86 bytes dwc3-generic-peripheral usb@38100000: request 00000000ffb29c40 was not queued to ep1in-bulk downloading of 86 bytes finished dwc3-generic-peripheral usb@38100000: request 00000000ffb29c40 was not queued to ep1in-bulk dwc3-generic-peripheral usb@38100000: request 00000000ffb29c40 was not queued to ep1in-bulk Starting download of 47173400 bytes dwc3-generic-peripheral usb@38100000: request 00000000ffb29c40 was not queued to ep1in-bulk ....................................................................... ... ....................................................................... ... ....................................................................... ... ....................................................................... ... ............................................................... downloading of 47173400 bytes finished dwc3-generic-peripheral usb@38100000: request 00000000ffb29c40 was not queued to ep1in-bulk dwc3-generic-peripheral usb@38100000: request 00000000ffb29c40 was not queued to ep1in-bulk Thanks, Joao Paulo

2 2

[PATCH] Makefile: Force regeneration of env.txt
by Andrew Davis 15 Sep '23

15 Sep '23

If the source .env file changes to one that is also older than the generated env.txt file then it is not regenerated. This means when switching board configs we do not regenerate the env. This can be tested easily with: $ make j721e_evm_a72_defconfig $ make # this may fail to complete but that is okay for this test $ make am64x_evm_a53_defconfig $ make $ vim include/generated/env.txt Note this is still the J721e env not the AM64 config as expected. There is probably a better way to detect if the dependency name changed, but that may involve extra files and hashing contents, so let's just force it for now. Signed-off-by: Andrew Davis <afd(a)ti.com> --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index 9be24c4ec61..d195590d4b0 100644 --- a/Makefile +++ b/Makefile @@ -1830,7 +1830,7 @@ quiet_cmd_envc = ENVC $@ touch $@ ; \ fi -include/generated/env.txt: $(wildcard $(ENV_FILE)) +include/generated/env.txt: $(wildcard $(ENV_FILE)) FORCE $(call cmd,envc) # Write out the resulting environment, converted to a C string -- 2.39.2

2 3

[PATCH] net: eth-uclass: Setup ROM source only when ROM reading passes
by Michal Simek 15 Sep '23

15 Sep '23

There is no reason to setup ROM source if read_rom_hwaddr hook doesn't exist or reading mac address fails. It is ending up with confusion about mac address source. It is nicely visible if you put mac address to DT as local-mac-address = [ff ff ff ff ff ff]; but also save ethaddr to variables setenv -f ethaddr 02:18:31:7e:3e:01 Before this patch U-Boot prints that source is DT Address in ROM is ff:ff:ff:ff:ff:ff Address in environment is 02:18:31:7e:3e:01 After that source is DT: Address in DT is ff:ff:ff:ff:ff:ff Address in environment is 02:18:31:7e:3e:01 Signed-off-by: Michal Simek <michal.simek(a)amd.com> --- net/eth-uclass.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-) diff --git a/net/eth-uclass.c b/net/eth-uclass.c index c393600fabcd..e40b869e1c31 100644 --- a/net/eth-uclass.c +++ b/net/eth-uclass.c @@ -588,10 +588,14 @@ static int eth_post_probe(struct udevice *dev) /* Check if the device has a valid MAC address in device tree */ if (!eth_dev_get_mac_address(dev, pdata->enetaddr) || !is_valid_ethaddr(pdata->enetaddr)) { - source = "ROM"; /* Check if the device has a MAC address in ROM */ - if (eth_get_ops(dev)->read_rom_hwaddr) - eth_get_ops(dev)->read_rom_hwaddr(dev); + if (eth_get_ops(dev)->read_rom_hwaddr) { + int ret; + + ret = eth_get_ops(dev)->read_rom_hwaddr(dev); + if (!ret) + source = "ROM"; + } } eth_env_get_enetaddr_by_index("eth", dev_seq(dev), env_enetaddr); -- 2.36.1

1 0

[PATCH 1/5] armv8: fsl-layerscape: make some functions static
by Laurentiu Tudor 15 Sep '23

15 Sep '23

Some functions are not used outside this file, so make them static. Signed-off-by: Laurentiu Tudor <laurentiu.tudor(a)nxp.com> --- arch/arm/cpu/armv8/fsl-layerscape/icid.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/arm/cpu/armv8/fsl-layerscape/icid.c b/arch/arm/cpu/armv8/fsl-layerscape/icid.c index ad20d71717b3..c22e73253c3c 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/icid.c +++ b/arch/arm/cpu/armv8/fsl-layerscape/icid.c @@ -23,8 +23,8 @@ static void set_icid(struct icid_id_table *tbl, int size) out_be32((u32 *)(tbl[i].reg_addr), tbl[i].reg); } -#ifdef CONFIG_SYS_DPAA_FMAN -void set_fman_icids(struct fman_icid_id_table *tbl, int size) +#if defined(CONFIG_SYS_DPAA_FMAN) && !defined(CONFIG_SPL_BUILD) +static void set_fman_icids(struct fman_icid_id_table *tbl, int size) { int i; ccsr_fman_t *fm = (void *)CFG_SYS_FSL_FM1_ADDR; @@ -71,7 +71,7 @@ int fdt_set_iommu_prop(void *blob, int off, int smmu_ph, u32 *ids, int num_ids) return 0; } -int fdt_fixup_icid_tbl(void *blob, int smmu_ph, +static int fdt_fixup_icid_tbl(void *blob, int smmu_ph, struct icid_id_table *tbl, int size) { int i, err, off; @@ -98,7 +98,7 @@ int fdt_fixup_icid_tbl(void *blob, int smmu_ph, } #ifdef CONFIG_SYS_DPAA_FMAN -int get_fman_port_icid(int port_id, struct fman_icid_id_table *tbl, +static int get_fman_port_icid(int port_id, struct fman_icid_id_table *tbl, const int size) { int i; @@ -111,7 +111,7 @@ int get_fman_port_icid(int port_id, struct fman_icid_id_table *tbl, return -1; } -void fdt_fixup_fman_port_icid_by_compat(void *blob, int smmu_ph, +static void fdt_fixup_fman_port_icid_by_compat(void *blob, int smmu_ph, const char *compat) { int noff, len, icid; @@ -140,7 +140,7 @@ void fdt_fixup_fman_port_icid_by_compat(void *blob, int smmu_ph, } } -void fdt_fixup_fman_icids(void *blob, int smmu_ph) +static void fdt_fixup_fman_icids(void *blob, int smmu_ph) { static const char * const compats[] = { "fsl,fman-v3-port-oh", -- 2.17.1

2 8

[PATCH] arm64: zynqmp: Corrected pcap_prog register address
by lukas.funke-oss＠weidmueller.com 15 Sep '23

15 Sep '23

From: Lukas Funke <lukas.funke(a)weidmueller.com> Currently the pcap_prog struct variable is pointing to 0x3004 which is incorrect according to [1]. The variable should point to 0x3000. [1] https://www.xilinx.com/htmldocs/registers/ug1087/ug1087-zynq-ultrascale-reg… Signed-off-by: Lukas Funke <lukas.funke(a)weidmueller.com> --- arch/arm/mach-zynqmp/include/mach/hardware.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-zynqmp/include/mach/hardware.h b/arch/arm/mach-zynqmp/include/mach/hardware.h index 634bf169c6..8cb6494e52 100644 --- a/arch/arm/mach-zynqmp/include/mach/hardware.h +++ b/arch/arm/mach-zynqmp/include/mach/hardware.h @@ -166,7 +166,7 @@ struct csu_regs { u32 jtag_dap_cfg; u32 idcode; u32 version; - u32 reserved2[3055]; + u32 reserved2[3054]; u32 pcap_prog; }; -- 2.30.2

2 1

[PATCH v2] global: Use proper project name U-Boot (next2)
by Michal Simek 15 Sep '23

15 Sep '23

Use proper project name in README, rst and comment. Done in connection to commit bb922ca3eb4b ("global: Use proper project name U-Boot (next)"). Signed-off-by: Michal Simek <michal.simek(a)amd.com> --- Changes in v2: - Revert change in tools/binman/entries.rst reported by Simon board/cobra5272/README | 18 +++++++++--------- board/emulation/qemu-ppce500/qemu-ppce500.c | 2 +- doc/board/xilinx/zynq.rst | 2 +- doc/board/xilinx/zynqmp-r5.rst | 4 ++-- doc/imx/mkimage/imximage.txt | 2 +- doc/usage/environment.rst | 2 +- doc/usage/semihosting.rst | 2 +- 7 files changed, 16 insertions(+), 16 deletions(-) diff --git a/board/cobra5272/README b/board/cobra5272/README index 11abcfacdb6e..0b07148b73a3 100644 --- a/board/cobra5272/README +++ b/board/cobra5272/README @@ -1,6 +1,6 @@ File: README.COBRA5272 Author: Florian Schlote for Sentec elektronik (linux(a)sentec-elektronik.de) -Contents: This is the README of u-boot (Universal bootloader) for our +Contents: This is the README of U-Boot (Universal bootloader) for our COBRA5272 board. Version: v01.00 Date: Tue Mar 30 00:28:33 CEST 2004 @@ -31,7 +31,7 @@ Please refer to u-boot README (general info, u-boot-x-x-x/README), to u-boot-x-x-x/board/cobra5272/README and to the comments in u-boot-x-x-x/include/configs/cobra5272.h -Configuring u-boot is done by commenting/uncommenting preprocessor defines. +Configuring U-Boot is done by commenting/uncommenting preprocessor defines. Default configuration is @@ -48,10 +48,10 @@ Default configuration is #----------------------------------- -# u-boot FLASH version & RAM version +# U-Boot FLASH version & RAM version #----------------------------------- -The u-boot bootloader for Coldfire processors can be configured +The U-Boot bootloader for Coldfire processors can be configured 1. as a standalone bootloader residing in flash & relocating itself to RAM on startup automatically => "FLASH version" @@ -60,7 +60,7 @@ The u-boot bootloader for Coldfire processors can be configured prestage bootloader ("chainloading") & is running only from the RAM address it is linked to => "RAM version" - This version may be very helpful when installing u-boot for the first time + This version may be very helpful when installing U-Boot for the first time since it can be used to make available s. th. like a "bootstrap mechanism". @@ -71,7 +71,7 @@ How to build the different images: Flash version ------------------------------ -Compile u-boot +Compile U-Boot in dir ./u-boot-x-x-x/ @@ -81,14 +81,14 @@ please first check: CONFIG_MONITOR_IS_IN_RAM has to be not present in the file - => u-boot as single bootloader starting from flash + => U-Boot as single bootloader starting from flash in configs/cobra5272_defconfig CONFIG_TEXT_BASE should be CONFIG_TEXT_BASE=0xffe00000 - => linking address for u-boot as single bootloader stored in flash + => linking address for U-Boot as single bootloader stored in flash then: @@ -116,7 +116,7 @@ please modify the settings: CONFIG_MONITOR_IS_IN_RAM=y - => u-boot as RAM version, chainloaded by another bootloader or using bdm cable + => U-Boot as RAM version, chainloaded by another bootloader or using bdm cable in configs/cobra5272_defconfig CONFIG_TEXT_BASE should be diff --git a/board/emulation/qemu-ppce500/qemu-ppce500.c b/board/emulation/qemu-ppce500/qemu-ppce500.c index a39bcb4fa0c7..40fd9e5e02b1 100644 --- a/board/emulation/qemu-ppce500/qemu-ppce500.c +++ b/board/emulation/qemu-ppce500/qemu-ppce500.c @@ -318,7 +318,7 @@ ulong get_bus_freq(ulong dummy) int cpu_numcores(void) { /* - * The QEMU u-boot target only needs to drive the first core, + * The QEMU U-Boot target only needs to drive the first core, * spinning and device tree nodes get driven by QEMU itself */ return 1; diff --git a/doc/board/xilinx/zynq.rst b/doc/board/xilinx/zynq.rst index 438912fe42c2..76d67bd62ee9 100644 --- a/doc/board/xilinx/zynq.rst +++ b/doc/board/xilinx/zynq.rst @@ -83,7 +83,7 @@ Mainline status --------------- - Added basic board configurations support. -- Added zynq u-boot bsp code - arch/arm/mach-zynq +- Added zynq U-Boot bsp code - arch/arm/mach-zynq - Added zynq boards named - zc70x, zed, microzed, zc770_xm010/xm011/xm012/xm013 - Added zynq drivers: diff --git a/doc/board/xilinx/zynqmp-r5.rst b/doc/board/xilinx/zynqmp-r5.rst index 2cd368b0308e..266d07d1193f 100644 --- a/doc/board/xilinx/zynqmp-r5.rst +++ b/doc/board/xilinx/zynqmp-r5.rst @@ -26,7 +26,7 @@ configure and build armv7 toolchain:: Notes ^^^^^ -Output fragment is u-boot. +Output fragment is U-Boot. Loading ------- @@ -38,7 +38,7 @@ Bootgen ^^^^^^^ The first way is to use Xilinx FSBL (First stage -bootloader) to load u-boot and start it. The following bif can be used for boot +bootloader) to load U-Boot and start it. The following bif can be used for boot image generation via Xilinx bootgen utility:: diff --git a/doc/imx/mkimage/imximage.txt b/doc/imx/mkimage/imximage.txt index f2cf23c5dab8..fa4e486661c2 100644 --- a/doc/imx/mkimage/imximage.txt +++ b/doc/imx/mkimage/imximage.txt @@ -213,7 +213,7 @@ Disk identifier: 0xb712a870 Device Boot Start End Blocks Id System /dev/mmcblk0p1 3 16 112455 83 Linux -I have set 100MB, leaving the first 2 sectors free. I will copy u-boot +I have set 100MB, leaving the first 2 sectors free. I will copy U-Boot there. 8. Write the partition table and exit. diff --git a/doc/usage/environment.rst b/doc/usage/environment.rst index c6439dde6689..c57b717caaf3 100644 --- a/doc/usage/environment.rst +++ b/doc/usage/environment.rst @@ -216,7 +216,7 @@ fdt_high 0xffffffffffffffff (64-bit machines) then the fdt will not be copied at all on boot. For this to work it must reside in writable memory, have - sufficient padding on the end of it for u-boot to + sufficient padding on the end of it for U-Boot to add the information it needs into it, and the memory must be accessible by the kernel. This usage is strongly discouraged however as it also stops U-Boot from ensuring the device tree starting diff --git a/doc/usage/semihosting.rst b/doc/usage/semihosting.rst index 6a280b455e0c..9303a6364d5d 100644 --- a/doc/usage/semihosting.rst +++ b/doc/usage/semihosting.rst @@ -23,7 +23,7 @@ eMMC or other NV media are available. There are two main ARM virtual Fixed Virtual Platform (FVP) models, `Versatile Express (VE) FVP and BASE FVP <http://www.arm.com/products/tools/models/fast-models/foundation-model.php>`_. -The initial vexpress64 u-boot board created here runs on the VE virtual +The initial vexpress64 U-Boot board created here runs on the VE virtual platform using the license-free Foundation_v8 simulator. Fortunately, the Foundation_v8 simulator also supports the BASE_FVP model which companies can purchase licenses for and contain much more functionality. -- 2.36.1

2 2

[PATCH v1 1/2] meson-a1: dts: add hw rng node
by Alexey Romanov 15 Sep '23

15 Sep '23

Add support for hardware random number generator of Amlogic Meson SoCs. Signed-off-by: Alexey Romanov <avromanov(a)sberdevices.ru> --- arch/arm/dts/meson-a1.dtsi | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/dts/meson-a1.dtsi b/arch/arm/dts/meson-a1.dtsi index f3560cbc3a4..1f57c137384 100644 --- a/arch/arm/dts/meson-a1.dtsi +++ b/arch/arm/dts/meson-a1.dtsi @@ -140,6 +140,11 @@ clock-names = "xtal", "pclk", "baud"; status = "disabled"; }; + + hwrng: rng@5118 { + compatible = "amlogic,meson-rng"; + reg = <0x0 0x5118 0x0 0x4>; + }; }; gic: interrupt-controller@ff901000 { -- 2.38.1

4 5

[PATCH v2 0/6] Add EFI HTTP boot support
by Masahisa Kojima 15 Sep '23

15 Sep '23

This series adds the EFI HTTP boot support. User can add the URI device path with "efidebug boot add" command. efibootmgr handles the URI device path, download the specified file using wget, mount the downloaded image with blkmap, then boot with the default file(e.g. EFI/BOOT/BOOTAA64.EFI). This version still does not include the test. To enable EFI HTTP boot, we need to enable the following Kconfig options. CONFIG_CMD_DNS CONFIG_CMD_WGET CONFIG_BLKMAP On the Socionext Developerbox, enter the following commands then debian installer is downloaded into "loadaddr" and installer automatically starts. => dhcp => setenv serverip 192.168.1.1 => efidebug boot add -u 3 debian-netinst http://ftp.riken.jp/Linux/debian/debian-cd/12.1.0/arm64/iso-cd/debian-12.1.… => efidebug boot order 3 => bootefi bootmgr Note that this debian installer can not proceed the installation bacause RAM disk of installer image is not recogniged by the kernel. I'm still investigating this issue, but drivers/nvdimm/of_pmem.c in linux will be one of the solution to recognize RAM disk from kernel. (In EDK2, the equivalent solution is called ACPI NFIT.) On QEMU, I can not make DNS work from the QEMU guest. The following commands work on qemu_arm64(manually set the http server ip in URI). => dhcp => setenv gatewayip 10.0.2.2 => setenv httpserverip 134.160.38.1 => efidebug boot add -u 3 debian-netinst http://134.160.38.1/Linux/debian/debian-cd/12.1.0/arm64/iso-cd/debian-12.1.… => efidebug boot order 3 => bootefi bootmgr [TODO] - add test - stricter wget uri check - omit the dns process if the given uri has ip address -> this will be supported when the lwip migration completes [change log] v1 -> v2 - carve out the network handling(wget and dns code) under net/wget.c - carve out ramdisk creation code under drivers/block/blkmap_helper.c - wget supports the valid range check to store the received blocks using lmb - support when the downloaded image have no partiton table but a file system - not start the .efi file in try_load_entry() - call efi_check_pe() for .efi file to check the file is PE-COFF image - add documentation for EFI HTTP Boot Masahisa Kojima (6): net: wget: prevent overwriting reserved memory net: wget: add wget with dns utility function blk: blkmap: add ramdisk creation utility function efi_loader: support boot from URI device path cmd: efidebug: add uri device path doc: uefi: add HTTP Boot support cmd/efidebug.c | 50 +++++++++ doc/develop/uefi/uefi.rst | 21 ++++ drivers/block/Makefile | 1 + drivers/block/blkmap.c | 15 --- drivers/block/blkmap_helper.c | 53 +++++++++ include/blkmap.h | 29 +++++ include/net.h | 8 ++ lib/efi_loader/efi_bootmgr.c | 197 +++++++++++++++++++++++++++++++++ net/wget.c | 202 ++++++++++++++++++++++++++++++++-- 9 files changed, 554 insertions(+), 22 deletions(-) create mode 100644 drivers/block/blkmap_helper.c base-commit: cc889bd0754e50a3cd50e8ed3094388480fbec86 -- 2.34.1

4 21

[PATCH] spi: zynqmp_qspi: Workaround for small data cache issue
by Venkatesh Yadav Abbarapu 15 Sep '23

15 Sep '23

Cache related issues are seen with small sized data reads. Due to this, proper data is not read. Also some times sf probe fails randomly. To workaround this issue, invalidate dcache after read DMA is triggered. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma(a)amd.com> Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu(a)amd.com> --- drivers/spi/zynqmp_gqspi.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/spi/zynqmp_gqspi.c b/drivers/spi/zynqmp_gqspi.c index a506d15227..ec59ef5804 100644 --- a/drivers/spi/zynqmp_gqspi.c +++ b/drivers/spi/zynqmp_gqspi.c @@ -707,6 +707,8 @@ static int zynqmp_qspi_start_dma(struct zynqmp_qspi_priv *priv, return -ETIMEDOUT; } + invalidate_dcache_range(addr, addr + size); + writel(GQSPI_DMA_DST_I_STS_DONE, &dma_regs->dmaisr); debug("buf:0x%lx, rxbuf:0x%lx, *buf:0x%x len: 0x%x\n", -- 2.17.1

3 2

[PATCH 00/35] treewide: Remove unused NEEDS_MANUAL_RELOC code bits
by Marek Vasut 15 Sep '23

15 Sep '23

The last user of the NEEDS_MANUAL_RELOC has been removed in commit 26af162ac8f8 ("arch: m68k: Implement relocation") Remove now unused NEEDS_MANUAL_RELOC code. This is a follow up on way over decade old commit 2e5167ccad93 ("Replace CONFIG_RELOC_FIXUP_WORKS by CONFIG_NEEDS_MANUAL_RELOC") " By now, the majority of architectures have working relocation support, so the few remaining architectures have become exceptions. To make this more obvious, we make working relocation now the default case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC. " It took a bit longer than expected, but now we can really sunset CONFIG_NEEDS_MANUAL_RELOC. Make it so. Marek Vasut (35): boot: Remove unused NEEDS_MANUAL_RELOC code bits blkcache: Remove unused NEEDS_MANUAL_RELOC code bits command: Remove unused NEEDS_MANUAL_RELOC code bits common: board_r: Remove unused NEEDS_MANUAL_RELOC code bits common: hush: Remove unused NEEDS_MANUAL_RELOC code bits common: malloc: Remove unused NEEDS_MANUAL_RELOC code bits common: event: Remove unused NEEDS_MANUAL_RELOC code bits common: hash: Remove unused NEEDS_MANUAL_RELOC code bits common: stdio: Remove unused NEEDS_MANUAL_RELOC code bits cmd: bmp: Remove unused NEEDS_MANUAL_RELOC code bits cmd: date: Remove unused NEEDS_MANUAL_RELOC code bits cmd: i2c: Remove unused NEEDS_MANUAL_RELOC code bits cmd: nvedit: Remove unused NEEDS_MANUAL_RELOC code bits cmd: onenand: Remove unused NEEDS_MANUAL_RELOC code bits cmd: pxe: Remove unused NEEDS_MANUAL_RELOC code bits dm: Remove unused NEEDS_MANUAL_RELOC code bits env: Remove unused NEEDS_MANUAL_RELOC code bits initcall: Remove unused NEEDS_MANUAL_RELOC code bits image: Remove unused NEEDS_MANUAL_RELOC code bits fs: Remove unused NEEDS_MANUAL_RELOC code bits cpu: Remove unused NEEDS_MANUAL_RELOC code bits crypto: rsa: Remove unused NEEDS_MANUAL_RELOC code bits gpio: Remove unused NEEDS_MANUAL_RELOC code bits hwspinlock: Remove unused NEEDS_MANUAL_RELOC code bits sf: Remove unused NEEDS_MANUAL_RELOC code bits mtd: ubifs: Remove unused NEEDS_MANUAL_RELOC code bits net: eth: Remove unused NEEDS_MANUAL_RELOC code bits net: miiphybb: Remove unused NEEDS_MANUAL_RELOC code bits net: phy: Remove unused NEEDS_MANUAL_RELOC code bits serial: Remove unused NEEDS_MANUAL_RELOC code bits spi: Remove unused NEEDS_MANUAL_RELOC code bits sysreset: Remove unused NEEDS_MANUAL_RELOC code bits timer: Remove unused NEEDS_MANUAL_RELOC code bits wdt: Remove unused NEEDS_MANUAL_RELOC code bits post: Remove unused NEEDS_MANUAL_RELOC code bits boot/bootm_os.c | 14 ---- boot/image-sig.c | 28 ------- boot/image.c | 10 +-- cmd/blkcache.c | 13 ---- cmd/bootm.c | 14 ---- cmd/date.c | 8 +- cmd/i2c.c | 14 ---- cmd/nvedit.c | 11 --- cmd/onenand.c | 6 -- cmd/pxe.c | 14 ---- common/bmp.c | 7 -- common/board_r.c | 28 ------- common/cli_hush.c | 16 ---- common/dlmalloc.c | 14 ---- common/event.c | 14 ---- common/hash.c | 29 -------- common/stdio.c | 12 --- doc/README.POST | 5 -- drivers/block/blkcache.c | 16 ---- drivers/core/root.c | 81 --------------------- drivers/cpu/cpu-uclass.c | 27 ------- drivers/crypto/rsa_mod_exp/mod_exp_uclass.c | 13 ---- drivers/gpio/gpio-uclass.c | 30 -------- drivers/hwspinlock/hwspinlock-uclass.c | 21 ------ drivers/mtd/spi/sf-uclass.c | 16 ---- drivers/net/phy/miiphybb.c | 20 +---- drivers/net/phy/phy.c | 31 -------- drivers/serial/serial-uclass.c | 22 ------ drivers/serial/serial.c | 17 ----- drivers/spi/spi-uclass.c | 32 -------- drivers/sysreset/sysreset-uclass.c | 16 ---- drivers/timer/timer-uclass.c | 13 ---- drivers/watchdog/wdt-uclass.c | 23 ------ env/callback.c | 12 --- env/common.c | 5 -- env/env.c | 23 ------ fs/fs.c | 16 ---- fs/ubifs/ubifs.c | 6 -- include/blk.h | 6 -- include/command.h | 21 ------ include/env.h | 13 ---- include/event.h | 10 --- include/initcall.h | 7 -- include/phy.h | 8 -- include/post.h | 3 - include/relocate.h | 24 ------ lib/initcall.c | 10 --- net/eth-uclass.c | 26 ------- net/eth_common.c | 4 - post/post.c | 48 ------------ 50 files changed, 8 insertions(+), 869 deletions(-) -- 2.40.1

3 37