November 2022 - U-Boot

[PATCH 0/1] configs: imx8mp_evk: revert to old ram settings
by Manoj Sai 31 Jan '23

31 Jan '23

revert the ram settings of imx8mp evk which are changed with commit id : 864ac2cf383e ("board: imx8mp: Add Engicam i.Core MX8M Plus EDIMM2.2 Starter Kit") Manoj Sai (1): configs: imx8mp_evk: revert to old ram settings include/configs/imx8mp_evk.h | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) -- 2.25.1

4 4

[PATCH 1/2] imx: mx6sabreauto: convert to DM_I2C
by Peng Fan (OSS) 31 Jan '23

31 Jan '23

From: Peng Fan <peng.fan(a)nxp.com> Convert to DM_I2C Signed-off-by: Peng Fan <peng.fan(a)nxp.com> --- configs/mx6sabreauto_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/configs/mx6sabreauto_defconfig b/configs/mx6sabreauto_defconfig index 2566f2a97fc..405f8f3d549 100644 --- a/configs/mx6sabreauto_defconfig +++ b/configs/mx6sabreauto_defconfig @@ -75,7 +75,7 @@ CONFIG_ARP_TIMEOUT=200 CONFIG_BOUNCE_BUFFER=y CONFIG_DFU_MMC=y CONFIG_DFU_SF=y -CONFIG_SYS_I2C_LEGACY=y +CONFIG_DM_I2C=y CONFIG_SPL_SYS_I2C_LEGACY=y CONFIG_SYS_I2C_MXC=y CONFIG_FSL_USDHC=y -- 2.36.0

2 3

[PATCH] configs: imx8mn_beacon_fspi: Add config for booting from QSPI
by Adam Ford 31 Jan '23

31 Jan '23

The imx8mn-beacon SOM has a QSPI part on it connected to the FlexSPI controller. Add a defconfig option which supports booting from the QSPI NOR flash instead of sd/mmc. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/configs/imx8mn_beacon_fspi_defconfig b/configs/imx8mn_beacon_fspi_defconfig new file mode 100644 index 0000000000..27b60824f3 --- /dev/null +++ b/configs/imx8mn_beacon_fspi_defconfig @@ -0,0 +1,156 @@ +CONFIG_ARM=y +CONFIG_ARCH_IMX8M=y +CONFIG_TEXT_BASE=0x40200000 +CONFIG_SYS_MALLOC_LEN=0x2000000 +CONFIG_SPL_GPIO=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_ENV_SIZE=0x2000 +CONFIG_ENV_OFFSET=0xFFFFDE00 +CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="imx8mn-beacon-kit" +CONFIG_SPL_TEXT_BASE=0x912000 +CONFIG_TARGET_IMX8MN_BEACON=y +CONFIG_SYS_PROMPT="u-boot=> " +CONFIG_SPL_SERIAL=y +CONFIG_SPL_DRIVERS_MISC=y +CONFIG_SPL=y +CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000 +CONFIG_SYS_LOAD_ADDR=0x42000000 +CONFIG_SYS_MEMTEST_START=0x40000000 +CONFIG_SYS_MEMTEST_END=0x44000000 +CONFIG_LTO=y +CONFIG_REMAKE_ELF=y +CONFIG_SYS_MONITOR_LEN=524288 +CONFIG_FIT=y +CONFIG_FIT_EXTERNAL_OFFSET=0x3000 +CONFIG_SPL_LOAD_FIT=y +# CONFIG_USE_SPL_FIT_GENERATOR is not set +CONFIG_OF_SYSTEM_SETUP=y +CONFIG_USE_BOOTCOMMAND=y +CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; else if run loadimage; then run mmcboot; else run netboot; fi; fi; else booti ${loadaddr} - ${fdt_addr}; fi" +CONFIG_DEFAULT_FDT_FILE="imx8mn-beacon-kit.dtb" +CONFIG_ARCH_MISC_INIT=y +CONFIG_SPL_MAX_SIZE=0x25000 +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y +CONFIG_SPL_BSS_START_ADDR=0x950000 +CONFIG_SPL_BSS_MAX_SIZE=0x2000 +CONFIG_SPL_BOARD_INIT=y +CONFIG_SPL_BOOTROM_SUPPORT=y +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set +CONFIG_SPL_STACK=0x980000 +CONFIG_SYS_SPL_MALLOC=y +CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y +CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x42200000 +CONFIG_SYS_SPL_MALLOC_SIZE=0x80000 +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300 +CONFIG_SPL_I2C=y +CONFIG_SPL_POWER=y +CONFIG_SPL_WATCHDOG=y +CONFIG_HUSH_PARSER=y +CONFIG_SYS_MAXARGS=64 +CONFIG_SYS_CBSIZE=2048 +CONFIG_SYS_PBSIZE=2074 +# CONFIG_BOOTM_NETBSD is not set +CONFIG_SYS_BOOTM_LEN=0x800000 +# CONFIG_CMD_EXPORTENV is not set +# CONFIG_CMD_IMPORTENV is not set +CONFIG_CMD_ERASEENV=y +# CONFIG_CMD_CRC32 is not set +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_CLK=y +CONFIG_CMD_FUSE=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PART=y +CONFIG_CMD_SPI=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_REGULATOR=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_FAT=y +CONFIG_OF_CONTROL=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_NOWHERE=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_SYS_MMC_ENV_DEV=2 +CONFIG_SYS_MMC_ENV_PART=2 +CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y +CONFIG_USE_ETHPRIME=y +CONFIG_ETHPRIME="FEC" +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_SPL_DM=y +CONFIG_REGMAP=y +CONFIG_SYSCON=y +CONFIG_SPL_CLK_IMX8MN=y +CONFIG_CLK_IMX8MN=y +CONFIG_USB_FUNCTION_FASTBOOT=y +CONFIG_FASTBOOT_BUF_ADDR=0x42800000 +CONFIG_FASTBOOT_BUF_SIZE=0x40000000 +CONFIG_FASTBOOT_FLASH=y +CONFIG_FASTBOOT_FLASH_MMC_DEV=0 +CONFIG_MXC_GPIO=y +CONFIG_DM_PCA953X=y +CONFIG_DM_I2C=y +CONFIG_SUPPORT_EMMC_BOOT=y +CONFIG_MMC_IO_VOLTAGE=y +CONFIG_MMC_UHS_SUPPORT=y +CONFIG_MMC_HS400_ES_SUPPORT=y +CONFIG_MMC_HS400_SUPPORT=y +CONFIG_FSL_USDHC=y +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SF_DEFAULT_SPEED=40000000 +CONFIG_SPI_FLASH_BAR=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_PHYLIB=y +CONFIG_PHY_ATHEROS=y +CONFIG_PHY_GIGE=y +CONFIG_FEC_MXC=y +CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_SPL_PINCTRL=y +CONFIG_PINCTRL_IMX8M=y +CONFIG_DM_PMIC=y +# CONFIG_SPL_PMIC_CHILDREN is not set +CONFIG_DM_PMIC_BD71837=y +CONFIG_SPL_DM_PMIC_BD71837=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_BD71837=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_DM_RESET=y +CONFIG_DM_SERIAL=y +CONFIG_MXC_UART=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_NXP_FSPI=y +CONFIG_SYSRESET=y +CONFIG_SPL_SYSRESET=y +CONFIG_SYSRESET_PSCI=y +CONFIG_SYSRESET_WATCHDOG=y +CONFIG_DM_THERMAL=y +CONFIG_USB=y +# CONFIG_SPL_DM_USB is not set +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y +CONFIG_SDP_LOADADDR=0x0 +CONFIG_IMX_WATCHDOG=y +CONFIG_OF_LIBFDT_OVERLAY=y +CONFIG_FSPI_CONF_HEADER=y +CONFIG_FSPI_CONF_FILE="fspi_header.bin" -- 2.34.1

2 1

[PATCH] imx: imx6ul: kontron-sl-mx6ul: Disable CONFIG_FSL_QSPI_AHB_FULL_MAP to fix SPI NAND read access
by Frieder Schrempf 31 Jan '23

31 Jan '23

From: Frieder Schrempf <frieder.schrempf(a)kontron.de> The introduction of CONFIG_FSL_QSPI_AHB_FULL_MAP as default in: def88bce094e ("spi: fsl_qspi: Support to use full AHB space on i.MX") broke the SPI NAND read access on the Kontron SL i.MX6UL/ULL boards. Reading data from the flash returns garbage instead of the actual content. Fix this for now by disabling the introduced option. In the long run this should be fixed globally. Fixes: def88bce094e ("spi: fsl_qspi: Support to use full AHB space on i.MX") Signed-off-by: Frieder Schrempf <frieder.schrempf(a)kontron.de> --- configs/kontron-sl-mx6ul_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/configs/kontron-sl-mx6ul_defconfig b/configs/kontron-sl-mx6ul_defconfig index aa789fc6e5e..db4b684690f 100644 --- a/configs/kontron-sl-mx6ul_defconfig +++ b/configs/kontron-sl-mx6ul_defconfig @@ -95,6 +95,7 @@ CONFIG_MXC_UART=y CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_FSL_QSPI=y +# CONFIG_FSL_QSPI_AHB_FULL_MAP is not set CONFIG_MXC_SPI=y CONFIG_IMX_THERMAL=y CONFIG_USB=y -- 2.38.1

5 4

[PATCH] include/configs: mx6/mx7: drop dangling comments
by Peter Robinson 31 Jan '23

31 Jan '23

Cleanup some dangling comments left by automated migration processes that are no longer value. Signed-off-by: Peter Robinson <pbrobinson(a)gmail.com> --- include/configs/mx6_common.h | 4 ---- include/configs/mx7_common.h | 12 ------------ 2 files changed, 16 deletions(-) diff --git a/include/configs/mx6_common.h b/include/configs/mx6_common.h index 43145567544..f70c515b840 100644 --- a/include/configs/mx6_common.h +++ b/include/configs/mx6_common.h @@ -22,8 +22,4 @@ #include <asm/arch/imx-regs.h> #include <asm/mach-imx/gpio.h> -/* Miscellaneous configurable options */ - -/* MMC */ - #endif diff --git a/include/configs/mx7_common.h b/include/configs/mx7_common.h index 4704276a74d..7e83715a76f 100644 --- a/include/configs/mx7_common.h +++ b/include/configs/mx7_common.h @@ -20,16 +20,4 @@ /* Enable iomux-lpsr support */ #define CONFIG_IOMUX_LPSR -/* Miscellaneous configurable options */ - -/* UART */ - -/* MMC */ - -/* - * If we have defined the OPTEE ram size and not OPTEE it means that we were - * launched by OPTEE, because of that we shall skip all the low level - * initialization since it was already done by ATF or OPTEE - */ - #endif -- 2.38.1

3 2

[PATCH] tools: imx8mimage: Fix handle leak
by Mikhail Ilin 31 Jan '23

31 Jan '23

The handle "fd" was created in imx8mimage.c:178 by calling the "fopen" function and is lost in imx8mimage.c:210. Should close the 'fd' file descriptor before exiting the parse_cfg_file(char *name) function. Fixes: 6609c2663c9c ("tools: add i.MX8M image support") Signed-off-by: Mikhail Ilin <ilin.mikhail.ol(a)gmail.com> --- tools/imx8mimage.c | 1 + 1 file changed, 1 insertion(+) diff --git a/tools/imx8mimage.c b/tools/imx8mimage.c index 35d0a92bfd..3ca79d865a 100644 --- a/tools/imx8mimage.c +++ b/tools/imx8mimage.c @@ -207,6 +207,7 @@ static uint32_t parse_cfg_file(char *name) } } + fclose(fd); return 0; } -- 2.17.1

2 1

[PATCH] tools: imx8image: Fix handle leak
by Mikhail Ilin 31 Jan '23

31 Jan '23

The handle "fd" was created in imx8image.c:249 by calling the "fopen" function and is lost in imx8image.c:282. Should close the 'fd' file descriptor before exiting the parse_cfg_file(image_t *param_stack, char *name) function. Fixes: a2b96ece5be1 ("tools: add i.MX8/8X image support") Signed-off-by: Mikhail Ilin <ilin.mikhail.ol(a)gmail.com> --- tools/imx8image.c | 1 + 1 file changed, 1 insertion(+) diff --git a/tools/imx8image.c b/tools/imx8image.c index 01e1486911..395d5c64bd 100644 --- a/tools/imx8image.c +++ b/tools/imx8image.c @@ -279,6 +279,7 @@ static uint32_t parse_cfg_file(image_t *param_stack, char *name) } } + fclose(fd); return 0; } -- 2.17.1

3 2

[PATCH] tools: imximage: Fix check array index
by Mikhail Ilin 31 Jan '23

31 Jan '23

The struct dcd_v1_t is initialized to MAX_HW_CFG_SIZE_V1 (60) structs 'dcd_type_addr_data_t', so the indexes to use on its elements are [0,59]. But on line 478, the variable 'length' can take on the value 60, which applies to array overflow: cd_v1->addr_data[length].type Thus, it is necessary to tighten the check on the 'size' variable on line 463. Fixes: 0b0c6af38738 ("Prepare v2020.01") Signed-off-by: Mikhail Ilin <ilin.mikhail.ol(a)gmail.com> --- tools/imximage.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/imximage.c b/tools/imximage.c index d7edd3c52f..8d45c917e6 100644 --- a/tools/imximage.c +++ b/tools/imximage.c @@ -460,7 +460,7 @@ static void print_hdr_v1(struct imx_header *imx_hdr) uint32_t size, length, ver; size = dcd_v1->preamble.length; - if (size > (MAX_HW_CFG_SIZE_V1 * sizeof(dcd_type_addr_data_t))) { + if (size >= (MAX_HW_CFG_SIZE_V1 * sizeof(dcd_type_addr_data_t))) { fprintf(stderr, "Error: Image corrupt DCD size %d exceed maximum %d\n", (uint32_t)(size / sizeof(dcd_type_addr_data_t)), -- 2.17.1

2 1

[PATCH] arm: kirkwood: Add nas440 board, Marvell 88SE6121 AHCI
by Hajo Noerenberg 30 Jan '23

30 Jan '23

This adds support for the Seagate Blackarmor NAS440 (4-bay Kirkwood NAS box). Does it make sense to include support for a 10+ year old device? If yes, I would be willing to discuss and finalize this patch. If no, it will be archived here for the public, which is fine with me. For the NAS440 is the something special that hard disk drives 1 and 2 are connected to a 88SE6121 SATA-II controller, which is connected via PCIe. Hard disk drives 3 and 4 are directly connected to the 88F6281 SoC. - Add NAS440 dtb and associated files/configs * Includes support for HD44780 front LCD * Includes support for device LEDs (via 74AHC164 shift register) - Add Marvell 88SE6121 AHCI support. Thanks to Pali Rohár for recently adding the necessary Kirkwood PCIe driver. It works :) - Tested with my NAS440 hardware: ETH/USB/SATA/AHCI-SCSI/GPIO/LCD/LEDs ok As far as I can see this fully implements the support for this board within U-Boot. With the Linux kernel however there are problems, the kernel AHCI driver fails with "failed to IDENTIFY" messages for the 88SE6121 drive ports, which I could not solve yet despite comparison with the GPL sources from Seagate. Note: I am collecting various information and patches for the family of Blackarmor NAS boards at https://github.com/hn/seagate-blackarmor-nas Hajo --- arch/arm/dts/kirkwood-blackarmor-nas440.dts | 166 +++++++++ board/Seagate/nas440/Kconfig | 12 + board/Seagate/nas440/MAINTAINERS | 7 + board/Seagate/nas440/Makefile | 7 + board/Seagate/nas440/kwbimage.cfg | 156 ++++++++ board/Seagate/nas440/nas440.c | 378 ++++++++++++++++++++ configs/nas440_defconfig | 89 +++++ drivers/ata/ahci-pci.c | 1 + include/configs/nas440.h | 50 +++ 9 files changed, 866 insertions(+) create mode 100644 arch/arm/dts/kirkwood-blackarmor-nas440.dts create mode 100644 board/Seagate/nas440/Kconfig create mode 100644 board/Seagate/nas440/MAINTAINERS create mode 100644 board/Seagate/nas440/Makefile create mode 100644 board/Seagate/nas440/kwbimage.cfg create mode 100644 board/Seagate/nas440/nas440.c create mode 100644 configs/nas440_defconfig create mode 100644 include/configs/nas440.h diff --git a/arch/arm/dts/kirkwood-blackarmor-nas440.dts b/arch/arm/dts/kirkwood-blackarmor-nas440.dts new file mode 100644 index 0000000000..60e3fe6f0d --- /dev/null +++ b/arch/arm/dts/kirkwood-blackarmor-nas440.dts @@ -0,0 +1,166 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Device Tree file for Seagate Blackarmor NAS440 + * + * Copyright (C) 2021 Hajo Noerenberg <www.github.com/hn> + * Copyright (C) 2015 Andreas Fischer <af(a)bantuX.org> + * Copyright (C) 2014 Evgeni Dobrev <evgeni(a)studio-punkt.com> + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" + +/ { + model = "Seagate Blackarmor NAS440"; + compatible = "seagate,blackarmor-nas440","marvell,kirkwood-88f6281", + "marvell,kirkwood"; + + memory { /* 256 MB */ + device_type = "memory"; + reg = <0x00000000 0x10000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = &uart0; + }; + + gpio_poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; /* GPIO1-16 is MPP48 */ + }; + + gpio_keys { + compatible = "gpio-keys"; + + reset { + label = "Reset"; + linux,code = <KEY_POWER>; + gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; + }; + + button { + label = "Power"; + linux,code = <KEY_SLEEP>; + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; /* GPIO1-17 is MPP49 */ + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_power_socsata>; + pinctrl-names = "default"; + + socsata_power: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "SoC SATA Power"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 28 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +/* + * Serial port routed to connector CN4 + * + * pin 1 - TX (CPU's TX) + * pin 4 - RX (CPU's RX) + * pin 6 - GND + */ +&uart0 { + status = "okay"; +}; + +&pinctrl { + pinctrl-0 = <&pmx_button_reset &pmx_button_power>; + pinctrl-names = "default"; + + pmx_act_sata0: pmx-act-sata0 { + marvell,pins = "mpp15"; + marvell,function = "sata0"; + }; + + pmx_act_sata1: pmx-act-sata1 { + marvell,pins = "mpp16"; + marvell,function = "sata1"; + }; + + pmx_power_socsata: pmx-power-socsata { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + pmx_button_reset: pmx-button-reset { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + pmx_button_power: pmx-button-power { + marvell,pins = "mpp49"; + marvell,function = "gpio"; + }; +}; + +&sata { + status = "okay"; + nr-ports = <2>; +}; + +&pciec { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + adt7473: thermal@2e { + compatible = "adi,adt7473"; + reg = <0x2e>; + }; +}; + +&nand { + status = "okay"; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@8 { + reg = <8>; + }; + ethphy1: ethernet-phy@9 { + reg = <9>; + }; +}; + +&eth0 { + status = "okay"; + + ethernet0-port@0 { + phy-handle = <&ethphy0>; + }; +}; + +&eth1 { + status = "okay"; + + ethernet1-port@0 { + phy-handle = <&ethphy1>; + }; +}; diff --git a/board/Seagate/nas440/Kconfig b/board/Seagate/nas440/Kconfig new file mode 100644 index 0000000000..3f93d75cd4 --- /dev/null +++ b/board/Seagate/nas440/Kconfig @@ -0,0 +1,12 @@ +if TARGET_NAS440 + +config SYS_BOARD + default "nas440" + +config SYS_VENDOR + default "Seagate" + +config SYS_CONFIG_NAME + default "nas440" + +endif diff --git a/board/Seagate/nas440/MAINTAINERS b/board/Seagate/nas440/MAINTAINERS new file mode 100644 index 0000000000..dcea1316c5 --- /dev/null +++ b/board/Seagate/nas440/MAINTAINERS @@ -0,0 +1,7 @@ +NAS440 BOARD +M: Hajo Noerenberg <hajo-uboot(a)noerenberg.de> +S: Maintained +F: board/Seagate/nas440/ +F: include/configs/nas440.h +F: configs/nas440_defconfig +F: arch/arm/dts/kirkwood-blackarmor-nas440.dts diff --git a/board/Seagate/nas440/Makefile b/board/Seagate/nas440/Makefile new file mode 100644 index 0000000000..2a3ef746d3 --- /dev/null +++ b/board/Seagate/nas440/Makefile @@ -0,0 +1,7 @@ +# +# Copyright (C) 2014 Evgeni Dobrev <evgeni(a)studio-punkt.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := nas440.o diff --git a/board/Seagate/nas440/kwbimage.cfg b/board/Seagate/nas440/kwbimage.cfg new file mode 100644 index 0000000000..e71da11694 --- /dev/null +++ b/board/Seagate/nas440/kwbimage.cfg @@ -0,0 +1,156 @@ +# +# Copyright (C) 2021 Hajo Noerenberg <hajo-uboot(a)noerenberg.de> +# +# Based on nas220/kwbimage.cfg originally written by +# Evgeni Dobrev <evgeni(a)studio-punkt.com> +# +# Based on sheevaplug/kwbimage.cfg originally written by +# Prafulla Wadaskar <prafulla(a)marvell.com> +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Refer doc/README.kwbimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM nand +NAND_ECC_MODE default +NAND_PAGE_SIZE 0x0200 + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0 interface pad voltage to 1.8V +DATA 0xFFD100E0 0x1B1B1B9B + +DATA 0xFFD20134 0xBBBBBBBB +DATA 0xFFD20138 0x00BBBBBB + +#Dram initalization for SINGLE x16 CL=5 @ 400MHz +DATA 0xFFD01400 0x43000C30 # DDR Configuration register +# bit13-0: 0xa00 (2560 DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x39543000 # DDR Controller Control Low +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000833 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x0000000C # DDR Address Control +# bit1-0: 00, Cs0width=x8 +# bit3-2: 11, Cs0size=1Gb +# bit5-4: 00, Cs1width=nonexistent +# bit7-6: 00, Cs1size =nonexistent +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000C52 # DDR Mode +# bit2-0: 2, BurstLen=2 required +# bit3: 0, BurstType=0 required +# bit6-4: 4, CL=5 +# bit7: 0, TestMode=0 normal +# bit8: 0, DLL reset=0 normal +# bit11-9: 6, auto-precharge write recovery ???????????? +# bit12: 0, PD must be zero +# bit31-13: 0 required + +DATA 0xFFD01420 0x00000042 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 0, DDR drive strenght normal +# bit2: 0, DDR ODT control lsd (disabled) +# bit5-3: 000, required +# bit6: 1, DDR ODT control msb, (disabled) +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F1FF # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 0 +# bit8 : 0 +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00085520 +DATA 0xFFD0147C 0x00008552 + +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x07, Size (i.e. 128MB) + +DATA 0xFFD01508 0x00000000 # CS[1]n Base address to 0x0 + +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled + +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x003C0000 # DDR ODT Control (Low) +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above +# bit3-2: 01, ODT1 active NEVER! +# bit31-4: zero, required + +DATA 0xFFD0149C 0x0000F80F # CPU ODT Control + +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +#bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 + diff --git a/board/Seagate/nas440/nas440.c b/board/Seagate/nas440/nas440.c new file mode 100644 index 0000000000..43a08e61bf --- /dev/null +++ b/board/Seagate/nas440/nas440.c @@ -0,0 +1,378 @@ +/* + * Copyright (C) 2022 Hajo Noerenberg <hajo-uboot(a)noerenberg.de> + * + * Based on nas220.c originally written by + * Evgeni Dobrev <evgeni(a)studio-punkt.com> + * + * Based on sheevaplug.c originally written by + * Prafulla Wadaskar <prafulla(a)marvell.com> + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <init.h> +#include <netdev.h> +#include <asm/arch/cpu.h> +#include <asm/arch/soc.h> +#include <asm/arch/mpp.h> +#include <asm/global_data.h> +#include <asm/mach-types.h> +#include <linux/bitops.h> +#include <bootstage.h> +#include <linux/delay.h> +#include <asm/arch/gpio.h> +#include <version.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* + * GPIO pin names, input/output direction and default values + * + * NAS440_GPIO_BUTTON_LCD_LOWER, NAS440_GPIO_BUTTON_LCD_UPPER + * Buttons next to LC display, LOW if pressed + * + * NAS440_GPIO_BUTTON_POWER + * Power button at front of case, LOW if pressed + * + * NAS440_GPIO_BUTTON_RESET + * Reset button at back of case, LOW if pressed + * + * NAS440_GPIO_LCD_HD44780_* + * HD44780-compatible LC display, control via 8bit parallel data transfer + * + * NAS440_GPIO_LED_74AHC164_* + * Control front panel LEDs via 74AHC164 8bit shift register + * + * NAS440_GPIO_SOCSATA_POWER + * 12V Power for SoC SATA ports (NAS drives 3 and 4) + * + * NAS440_GPIO_BOARD_POWER + * Shutdown board if LOW + * + */ + +#define NAS440_GPIO_LCD_HD44780_BACKLIGHT 7 +#define NAS440_GPIO_LED_74AHC164_DATA 12 +#define NAS440_GPIO_LED_74AHC164_CLK 13 +#define NAS440_GPIO_SOCSATA_POWER 28 +#define NAS440_GPIO_BUTTON_RESET 29 +#define NAS440_GPIO_BUTTON_LCD_LOWER 34 +#define NAS440_GPIO_LCD_HD44780_RS 35 +#define NAS440_GPIO_LCD_HD44780_D0 36 +#define NAS440_GPIO_LCD_HD44780_D1 37 +#define NAS440_GPIO_LCD_HD44780_D2 38 +#define NAS440_GPIO_LCD_HD44780_D3 39 +#define NAS440_GPIO_LCD_HD44780_D4 40 +#define NAS440_GPIO_LCD_HD44780_D5 41 +#define NAS440_GPIO_LCD_HD44780_D6 42 +#define NAS440_GPIO_LCD_HD44780_D7 43 +#define NAS440_GPIO_LCD_HD44780_RW 44 +#define NAS440_GPIO_LCD_HD44780_E 45 +#define NAS440_GPIO_BUTTON_LCD_UPPER 47 +#define NAS440_GPIO_BOARD_POWER 48 +#define NAS440_GPIO_BUTTON_POWER 49 + +/* + * GPIO output enable, pins 0-31 to LOW, pins 31-49 to HIGH config register + */ +#define NAS440_GE_OE_LOW (~(BIT(NAS440_GPIO_LCD_HD44780_BACKLIGHT) \ + | BIT(NAS440_GPIO_LED_74AHC164_DATA) \ + | BIT(NAS440_GPIO_LED_74AHC164_CLK) \ + | BIT(NAS440_GPIO_SOCSATA_POWER))) +#define NAS440_GE_OE_HIGH (~(BIT_MASK(NAS440_GPIO_BOARD_POWER) \ + | BIT_MASK(NAS440_GPIO_LCD_HD44780_RS) \ + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D0) \ + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D1) \ + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D2) \ + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D3) \ + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D4) \ + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D5) \ + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D6) \ + | BIT_MASK(NAS440_GPIO_LCD_HD44780_D7) \ + | BIT_MASK(NAS440_GPIO_LCD_HD44780_RW) \ + | BIT_MASK(NAS440_GPIO_LCD_HD44780_E))) + +/* + * GPIO output default values + */ +#define NAS440_GE_OE_VAL_LOW BIT(NAS440_GPIO_LCD_HD44780_BACKLIGHT) + +#define NAS440_GE_OE_VAL_HIGH BIT_MASK(NAS440_GPIO_BOARD_POWER) + +int board_early_init_f(void) +{ + /* + * default gpio configuration + */ + mvebu_config_gpio(NAS440_GE_OE_VAL_LOW, NAS440_GE_OE_VAL_HIGH, + NAS440_GE_OE_LOW, NAS440_GE_OE_HIGH); + + /* Multi-Purpose Pins Functionality configuration */ + static const u32 kwmpp_config[] = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_GPO, /* NAS440_GPIO_LCD_HD44780_BACKLIGHT */ + MPP8_TW_SDA, + MPP9_TW_SCK, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_GPO, /* NAS440_GPIO_LED_74AHC164_DATA */ + MPP13_GPIO, /* NAS440_GPIO_LED_74AHC164_CLK */ + MPP14_SATA1_PRESENTn, + MPP15_SATA0_ACTn, + MPP16_SATA1_ACTn, + MPP17_SATA0_PRESENTn, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GE1_0, /* GbE Port1, RGMII mode (12 pins GE1_0-7, GE1_10-13) */ + MPP21_GE1_1, + MPP22_GE1_2, + MPP23_GE1_3, + MPP24_GE1_4, + MPP25_GE1_5, + MPP26_GE1_6, + MPP27_GE1_7, + MPP28_GPIO, /* NAS440_GPIO_SOCSATA_POWER */ + MPP29_GPIO, /* NAS440_GPIO_BUTTON_RESET */ + MPP30_GE1_10, + MPP31_GE1_11, + MPP32_GE1_12, + MPP33_GE1_13, + MPP34_GPIO, /* NAS440_GPIO_BUTTON_LCD_LOWER */ + MPP35_GPIO, /* NAS440_GPIO_LCD_HD44780_RS */ + MPP36_GPIO, /* NAS440_GPIO_LCD_HD44780_D0 */ + MPP37_GPIO, /* NAS440_GPIO_LCD_HD44780_D1 */ + MPP38_GPIO, /* NAS440_GPIO_LCD_HD44780_D2 */ + MPP39_GPIO, /* NAS440_GPIO_LCD_HD44780_D3 */ + MPP40_GPIO, /* NAS440_GPIO_LCD_HD44780_D4 */ + MPP41_GPIO, /* NAS440_GPIO_LCD_HD44780_D5 */ + MPP42_GPIO, /* NAS440_GPIO_LCD_HD44780_D6 */ + MPP43_GPIO, /* NAS440_GPIO_LCD_HD44780_D7 */ + MPP44_GPIO, /* NAS440_GPIO_LCD_HD44780_RW */ + MPP45_GPIO, /* NAS440_GPIO_LCD_HD44780_E */ + MPP46_GPIO, + MPP47_GPIO, /* NAS440_GPIO_BUTTON_LCD_UPPER */ + MPP48_GPIO, /* NAS440_GPIO_BOARD_POWER */ + MPP49_GPIO, /* NAS440_GPIO_BUTTON_POWER */ + 0 + }; + kirkwood_mpp_conf(kwmpp_config, NULL); + return 0; +} + +/* HD44780 pins, data bits first, backlight last */ +static int hd44780_pins[12] = { + NAS440_GPIO_LCD_HD44780_D0, + NAS440_GPIO_LCD_HD44780_D1, + NAS440_GPIO_LCD_HD44780_D2, + NAS440_GPIO_LCD_HD44780_D3, + NAS440_GPIO_LCD_HD44780_D4, + NAS440_GPIO_LCD_HD44780_D5, + NAS440_GPIO_LCD_HD44780_D6, + NAS440_GPIO_LCD_HD44780_D7, + NAS440_GPIO_LCD_HD44780_E, + NAS440_GPIO_LCD_HD44780_RW, + NAS440_GPIO_LCD_HD44780_RS, + NAS440_GPIO_LCD_HD44780_BACKLIGHT +}; + +#define HD44780_NUM_COL 16 +#define HD44780_BUF_COL 40 +#define HD44780_NUM_ROW 2 + +#define HD44780_PIN_NUM (sizeof(hd44780_pins)/sizeof(int)) + +/* + * HD44780 LCD display commands - adapted from hd44780.h by Joerg Wunsch + * + * ---------------------------------------------------------------------------- + * "THE BEER-WARE LICENSE" (Revision 42): + * <joerg(a)FreeBSD.ORG> wrote this file. As long as you retain this notice you + * can do whatever you want with this stuff. If we meet some day, and you think + * this stuff is worth it, you can buy me a beer in return. Joerg Wunsch + * ---------------------------------------------------------------------------- + */ + +#define HD44780_CMD_CLR \ + 0x01 +#define HD44780_CMD_HOME \ + 0x02 +#define HD44780_CMD_ENTMODE(inc, shift) \ + (0x04 | ((inc)? 0x02: 0) | ((shift)? 1: 0)) +#define HD44780_CMD_DISPCTL(disp, cursor, blink) \ + (0x08 | ((disp)? 0x04: 0) | ((cursor)? 0x02: 0) | ((blink)? 1: 0)) +#define HD44780_CMD_SHIFT(shift, right) \ + (0x10 | ((shift)? 0x08: 0) | ((right)? 0x04: 0)) +#define HD44780_CMD_FNSET(if8bit, twoline, font5x10) \ + (0x20 | ((if8bit)? 0x10: 0) | ((twoline)? 0x08: 0) | \ + ((font5x10)? 0x04: 0)) +#define HD44780_CMD_CGADDR(addr) \ + (0x40 | ((addr) & 0x3f)) +#define HD44780_CMD_DDADDR(addr) \ + (0x80 | ((addr) & 0x7f)) + +static void lcd_send(unsigned int val, int mode) +{ + udelay(1); + kw_gpio_set_value(NAS440_GPIO_LCD_HD44780_RS, mode); + udelay(1); + + kw_gpio_set_value(NAS440_GPIO_LCD_HD44780_E, 0); + for (int i=0; i<8; i++) { + kw_gpio_set_value(hd44780_pins[i], (val&(1<<i))>>i ); + } + udelay(1); + kw_gpio_set_value(NAS440_GPIO_LCD_HD44780_E, 1); + udelay(1); + kw_gpio_set_value(NAS440_GPIO_LCD_HD44780_E, 0); + udelay(50); +} + +void lcd_init(void) +{ + for (int i=0; i<HD44780_PIN_NUM; i++) { + kw_gpio_set_valid(hd44780_pins[i], GPIO_OUTPUT_OK); + kw_gpio_direction_output(hd44780_pins[i], i == (HD44780_PIN_NUM-1)); + } + + lcd_send(HD44780_CMD_FNSET(1, 1, 0), 0); + udelay(50); + lcd_send(HD44780_CMD_FNSET(1, 1, 0), 0); + udelay(50); + lcd_send(HD44780_CMD_FNSET(1, 1, 0), 0); + udelay(50); + lcd_send(HD44780_CMD_DISPCTL(1, 0, 0), 0); + udelay(50); + lcd_send(HD44780_CMD_CLR, 0); + udelay(50); + lcd_send(HD44780_CMD_ENTMODE(1, 0), 0); + + udelay(2000); +} + +void lcd_row(int row, char *buf) +{ + int p = 0; + + if (row >= HD44780_NUM_ROW) { + return; + } + + lcd_send(HD44780_CMD_DDADDR(HD44780_BUF_COL * row + 0), 0); + for (int i=0; i<HD44780_NUM_COL; i++) { + if (buf[i] == 0) { + p++; + } + lcd_send(p ? 32 : buf[i], 1); + } +} + +enum led_disk { + LED_DSK_OFF, + LED_DSK_RED + /* LED_DSK_GREEN disk activity led is controlled directly by the hardware */ +}; + +enum led_system { + LED_SYS_OFF, + LED_SYS_BLUE, + LED_SYS_RED +}; + +void led_init(void) +{ + kw_gpio_set_valid(NAS440_GPIO_LED_74AHC164_DATA, GPIO_OUTPUT_OK); + kw_gpio_direction_output(NAS440_GPIO_LED_74AHC164_DATA, 0); + kw_gpio_set_valid(NAS440_GPIO_LED_74AHC164_CLK, GPIO_OUTPUT_OK); + kw_gpio_direction_output(NAS440_GPIO_LED_74AHC164_CLK, 0); +} + +void led_set(enum led_disk disk1, enum led_disk disk2, enum led_disk disk3, + enum led_disk disk4, enum led_system front1 ) +{ + int ledbits = (0x81 | ((front1==LED_SYS_RED)? 0x08 : 0) | ((front1==LED_SYS_BLUE)? 0x04 : 0) \ + | ((disk1==LED_DSK_RED)? 0 : 0x02) | ((disk2==LED_DSK_RED)? 0 : 0x40) \ + | ((disk3==LED_DSK_RED)? 0 : 0x20) | ((disk4==LED_DSK_RED)? 0 : 0x10)); + + for (int i=0; i<8; i++) { + kw_gpio_set_value(NAS440_GPIO_LED_74AHC164_DATA, (ledbits >> i) & 1); + udelay(1); + kw_gpio_set_value(NAS440_GPIO_LED_74AHC164_CLK, 1); + kw_gpio_set_value(NAS440_GPIO_LED_74AHC164_CLK, 0); + } +} + +/* factory firmware delays hard disk spinup, presumably to avoid power peaks */ +void delay_hdd_spinup(void) +{ + lcd_row(1, "Delay HDD spinup"); + + for (int i = 0; i<2500; i++) { + udelay(1000); + } + + kw_gpio_set_valid(NAS440_GPIO_SOCSATA_POWER, GPIO_OUTPUT_OK); + kw_gpio_direction_output(NAS440_GPIO_SOCSATA_POWER, 1); +} + +#if CONFIG_IS_ENABLED(BOOTSTAGE) +void show_boot_progress(int val) +{ + switch (val) { +/* 0123456789abcdef */ + case BOOTSTAGE_ID_BOARD_INIT_DONE: + lcd_row(1, "Board init done"); + break; + case BOOTSTAGE_ID_USB_START: + lcd_row(1, "Init USB"); + break; + case BOOTSTAGE_ID_ETH_START: + lcd_row(1, "Init ethernet"); + break; + case BOOTSTAGE_ID_MAIN_LOOP: + lcd_row(1, "Wait for input"); + break; + case BOOTSTAGE_ID_RUN_OS: + lcd_row(1, "Starting Linux"); + break; + default: + if (val < 0) /* error */ + lcd_row(1, "Error"); + break; + } +} +#endif + +int board_eth_init(struct bd_info *bis) +{ + return cpu_eth_init(bis); +} + +int board_init(void) +{ + /* + * arch number of board + */ + gd->bd->bi_arch_number = MACH_TYPE_DB88F6281_BP; + + /* adress of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + + led_init(); + led_set(LED_DSK_OFF, LED_DSK_OFF, LED_DSK_OFF, LED_DSK_OFF, LED_SYS_BLUE); + + lcd_init(); + lcd_row(0, U_BOOT_VERSION ""); + + delay_hdd_spinup(); + + return 0; +} diff --git a/configs/nas440_defconfig b/configs/nas440_defconfig new file mode 100644 index 0000000000..74faf1a24b --- /dev/null +++ b/configs/nas440_defconfig @@ -0,0 +1,89 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_SYS_DCACHE_OFF=y +CONFIG_ARCH_CPU_INIT=y +CONFIG_ARCH_KIRKWOOD=y +CONFIG_SUPPORT_PASSING_ATAGS=y +CONFIG_CMDLINE_TAG=y +CONFIG_INITRD_TAG=y +CONFIG_SYS_KWD_CONFIG="board/Seagate/nas440/kwbimage.cfg" +CONFIG_SYS_TEXT_BASE=0x600000 +CONFIG_NR_DRAM_BANKS=2 +CONFIG_TARGET_NAS440=y +CONFIG_ENV_SIZE=0x10000 +CONFIG_ENV_OFFSET=0xA0000 +CONFIG_DEFAULT_DEVICE_TREE="kirkwood-blackarmor-nas440" +CONFIG_IDENT_STRING="\nNAS 440" +# CONFIG_SYS_MALLOC_F is not set +CONFIG_SYS_LOAD_ADDR=0x800000 +CONFIG_SHOW_BOOT_PROGRESS=y +CONFIG_BOOTSTAGE=y +CONFIG_BOOTDELAY=3 +CONFIG_USE_PREBOOT=y +CONFIG_PREBOOT="pci enum; " +# CONFIG_DISPLAY_BOARDINFO is not set +CONFIG_HUSH_PARSER=y +CONFIG_SYS_PROMPT="nas440> " +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_SATA=y +CONFIG_CMD_PCI=y +CONFIG_CMD_DM=y +CONFIG_CMD_SCSI=y +CONFIG_CMD_NAND=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_FAT=y +CONFIG_CMD_JFFS2=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0xa0000@0x0(uboot),0x010000@0xa0000(env),0x500000@0xc0000(uimage),0x1a40000@0x5c0000(rootfs)" +CONFIG_CMD_UBI=y +CONFIG_ISO_PARTITION=y +CONFIG_EFI_PARTITION=y +# CONFIG_PARTITION_UUIDS is not set +CONFIG_OF_CONTROL=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_NAND=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_NETCONSOLE=y +CONFIG_DM=y +CONFIG_SYS_ATA_STRIDE=4 +CONFIG_SYS_ATA_DATA_OFFSET=0x100 +CONFIG_SYS_ATA_REG_OFFSET=0x100 +CONFIG_SYS_ATA_ALT_OFFSET=0x100 +CONFIG_KIRKWOOD_GPIO=y +CONFIG_MVEBU_GPIO=y +CONFIG_GPIO_EXTRA_HEADER=y +CONFIG_DM_GPIO=y +CONFIG_CMD_GPIO=y +CONFIG_GPIO=y +CONFIG_DM_GPIO_LOOKUP_LABEL=y +# CONFIG_MMC is not set +CONFIG_MTD=y +CONFIG_MTD_RAW_NAND=y +CONFIG_PHY_MARVELL=y +CONFIG_DM_ETH=y +CONFIG_MVGBE=y +CONFIG_MII=y +CONFIG_SATA_MV=y +CONFIG_SYS_SATA_MAX_DEVICE=2 +CONFIG_DM_RTC=y +CONFIG_RTC_MV=y +CONFIG_SYS_NS16550=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_STORAGE=y + +CONFIG_PCI=y +CONFIG_DM_PCI_COMPAT=y +CONFIG_PCI_MVEBU=y +CONFIG_AHCI_PCI=y + +CONFIG_SCSI=y +CONFIG_SCSI_AHCI=y +CONFIG_DM_SCSI=y diff --git a/drivers/ata/ahci-pci.c b/drivers/ata/ahci-pci.c index b1d231e0f9..af7e97dc4a 100644 --- a/drivers/ata/ahci-pci.c +++ b/drivers/ata/ahci-pci.c @@ -38,6 +38,7 @@ U_BOOT_DRIVER(ahci_pci) = { static struct pci_device_id ahci_pci_supported[] = { { PCI_DEVICE_CLASS(PCI_CLASS_STORAGE_SATA_AHCI, ~0) }, { PCI_DEVICE(0x1b21, 0x0611) }, + { PCI_DEVICE(0x11ab, 0x6121) }, {}, }; diff --git a/include/configs/nas440.h b/include/configs/nas440.h new file mode 100644 index 0000000000..58e6afb2c3 --- /dev/null +++ b/include/configs/nas440.h @@ -0,0 +1,50 @@ +/* + * Copyright (C) 2022 Hajo Noerenberg <hajo-uboot(a)noerenberg.de> + * + * based on work from: + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar <prafulla(a)marvell.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_NAS440_H +#define _CONFIG_NAS440_H + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ + +#include "mv-common.h" + +/* + * Default environment variables + */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "bootargs=console=ttyS0,115200\0" \ + "mtdids=nand0=orion_nand\0"\ + "mtdparts=" CONFIG_MTDPARTS_DEFAULT \ + "autostart=no\0"\ + "autoload=no\0" + +/* + * Ethernet Driver configuration + */ +#ifdef CONFIG_MVGBE +#define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ +#define CONFIG_PHY_BASE_ADR 8 +#ifdef CONFIG_RESET_PHY_R +#undef CONFIG_RESET_PHY_R /* remove legacy reset_phy() */ +#endif +#endif /* CONFIG_MVGBE */ + +/* + * SATA driver configuration + */ +#define CONFIG_LBA48 +#define CONFIG_SYS_64BIT_LBA + +#endif /* _CONFIG_NAS440_H */ -- 2.20.1

3 11

[PATCH] phy: add of_set_phy_supported() helper, call from phy_config()
by Rasmus Villemoes 30 Jan '23

30 Jan '23

Currently, U-Boot doesn't parse a "max-speed" DT property in a phy's DT node. That property is a standard binding which should be honoured, and in linux that is done by the core phy code via a call to an of_set_phy_supported() helper. (Some ethernet drivers support a max-speed property in their DT node, but that's orthogonal to what the phy supports.) Add a similar helper in U-Boot, and call it from phy_config(). Signed-off-by: Rasmus Villemoes <rasmus.villemoes(a)prevas.dk> --- Resending, this time including the u-boot list in recipients. Sorry for the duplicate. drivers/net/phy/phy.c | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index e6e1755518..ec690361e6 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -599,6 +599,20 @@ int phy_register(struct phy_driver *drv) return 0; } +static int of_set_phy_supported(struct phy_device *phydev) +{ + ofnode node = phy_get_ofnode(phydev); + u32 max_speed; + + if (!ofnode_valid(node)) + return 0; + + if (!ofnode_read_u32(node, "max-speed", &max_speed)) + return phy_set_supported(phydev, max_speed); + + return 0; +} + int phy_set_supported(struct phy_device *phydev, u32 max_speed) { /* The default values for phydev->supported are provided by the PHY @@ -1070,6 +1084,12 @@ __weak int board_phy_config(struct phy_device *phydev) int phy_config(struct phy_device *phydev) { + int ret; + + ret = of_set_phy_supported(phydev); + if (ret) + return ret; + /* Invoke an optional board-specific helper */ return board_phy_config(phydev); } -- 2.31.1

4 7