September 2019 - U-Boot

[U-Boot] [PATCH] soc: ti: k3-navss-ringacc: fix k3_nav_ringacc_ring_reset_dma
by Vignesh Raghavendra 15 Sep '19

15 Sep '19

In case dma_ring_reset_quirk is not set the k3_ringacc_ring_reset_dma will just exit without ring reset. Fix it, by adding ring reset call in case dma_ring_reset_quirk is not. Signed-off-by: Grygorii Strashko <grygorii.strashko(a)ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr(a)ti.com> --- drivers/soc/ti/k3-navss-ringacc.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/soc/ti/k3-navss-ringacc.c b/drivers/soc/ti/k3-navss-ringacc.c index fcb84f7aa49b..64ebc0ba0030 100644 --- a/drivers/soc/ti/k3-navss-ringacc.c +++ b/drivers/soc/ti/k3-navss-ringacc.c @@ -366,8 +366,10 @@ void k3_nav_ringacc_ring_reset_dma(struct k3_nav_ring *ring, u32 occ) if (!ring || !(ring->flags & KNAV_RING_FLAG_BUSY)) return; - if (!ring->parent->dma_ring_reset_quirk) + if (!ring->parent->dma_ring_reset_quirk) { + k3_nav_ringacc_ring_reset(ring); return; + } if (!occ) occ = ringacc_readl(&ring->rt->occ); -- 2.23.0

2 1

[U-Boot] [PATCH] ARM: dts: dra74x: Fix iodelay configuration for mmc3
by Faiz Abbas 15 Sep '19

15 Sep '19

According to the latest am572x[1] and dra74x[2] data manuals, mmc3 default, hs, sdr12 and sdr25 modes use iodelay values given in MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is selected and correct iodelay values are configured. [1] http://www.ti.com/lit/ds/symlink/am5728.pdf [2] http://www.ti.com/lit/ds/symlink/dra746.pdf Signed-off-by: Faiz Abbas <faiz_abbas(a)ti.com> --- arch/arm/dts/dra74x-mmc-iodelay.dtsi | 50 ++++++++++++++-------------- 1 file changed, 25 insertions(+), 25 deletions(-) diff --git a/arch/arm/dts/dra74x-mmc-iodelay.dtsi b/arch/arm/dts/dra74x-mmc-iodelay.dtsi index 28ebb4eb88..214b9e6de2 100644 --- a/arch/arm/dts/dra74x-mmc-iodelay.dtsi +++ b/arch/arm/dts/dra74x-mmc-iodelay.dtsi @@ -32,7 +32,7 @@ * * Datamanual Revisions: * - * AM572x Silicon Revision 2.0: SPRS953B, Revised November 2016 + * AM572x Silicon Revision 2.0: SPRS953F, Revised May 2019 * AM572x Silicon Revision 1.1: SPRS915R, Revised November 2016 * */ @@ -229,45 +229,45 @@ mmc3_pins_default: mmc3_pins_default { pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ - DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ - DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ - DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ - DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ - DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ + DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ + DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ + DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ + DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ + DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ + DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ >; }; mmc3_pins_hs: mmc3_pins_hs { pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ - DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ - DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ - DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ - DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ - DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ + DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ + DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ + DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ + DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ + DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ + DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ >; }; mmc3_pins_sdr12: mmc3_pins_sdr12 { pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ - DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ - DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ - DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ - DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ - DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ + DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ + DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ + DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ + DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ + DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ + DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ >; }; mmc3_pins_sdr25: mmc3_pins_sdr25 { pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ - DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ - DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ - DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ - DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ - DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ + DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ + DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ + DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ + DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ + DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ + DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ >; }; -- 2.19.2

2 1

[U-Boot] [PATCH 1/2] configs: ti: Add environment support commands for FIT loading
by Andrew F. Davis 15 Sep '19

15 Sep '19

Some parts of these commands can be reused, add them to common files. Signed-off-by: Andrew F. Davis <afd(a)ti.com> --- include/configs/am65x_evm.h | 3 +++ include/configs/ti_armv7_common.h | 8 +++++++- 2 files changed, 10 insertions(+), 1 deletion(-) diff --git a/include/configs/am65x_evm.h b/include/configs/am65x_evm.h index 6072e4a48c..0249a20ba8 100644 --- a/include/configs/am65x_evm.h +++ b/include/configs/am65x_evm.h @@ -94,11 +94,14 @@ "done;\0" \ "get_kern_mmc=load mmc ${bootpart} ${loadaddr} " \ "${bootdir}/${name_kern}\0" \ + "get_fit_mmc=load mmc ${bootpart} ${addr_fit} " \ + "${bootdir}/${name_fit}\0" \ "partitions=" PARTS_DEFAULT /* Incorporate settings into the U-Boot environment */ #define CONFIG_EXTRA_ENV_SETTINGS \ DEFAULT_MMC_TI_ARGS \ + DEFAULT_FIT_TI_ARGS \ EXTRA_ENV_AM65X_BOARD_SETTINGS \ EXTRA_ENV_AM65X_BOARD_SETTINGS_MMC diff --git a/include/configs/ti_armv7_common.h b/include/configs/ti_armv7_common.h index 2058f8de0f..2de6bc2390 100644 --- a/include/configs/ti_armv7_common.h +++ b/include/configs/ti_armv7_common.h @@ -55,7 +55,13 @@ "addr_fit=0x90000000\0" \ "name_fit=fitImage\0" \ "update_to_fit=setenv loadaddr ${addr_fit}; setenv bootfile ${name_fit}\0" \ - "loadfit=run args_mmc; bootm ${loadaddr}#${fdtfile};\0" \ + "get_overlaystring=" \ + "for overlay in $overlay_files;" \ + "do;" \ + "setenv overlaystring ${overlaystring}'#'${overlay};" \ + "done;\0" \ + "run_fit=bootm ${loadaddr}#${fdtfile}${overlaystring}\0" \ + "loadfit=run args_mmc; run run_fit;\0" \ /* * DDR information. If the CONFIG_NR_DRAM_BANKS is not defined, -- 2.17.1

2 3

[U-Boot] [PATCH 1/4] sh: Fix incorrect linking with new binutils
by Marek Vasut 14 Sep '19

14 Sep '19

Since binutils 2.30 , the resulting U-Boot binary was incorrectly linked against address 0 instead of text base, fix it. Signed-off-by: Marek Vasut <marek.vasut+renesas(a)gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu(a)nigauri.org> --- arch/sh/cpu/u-boot.lds | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/sh/cpu/u-boot.lds b/arch/sh/cpu/u-boot.lds index 47302da252..4cc97737f1 100644 --- a/arch/sh/cpu/u-boot.lds +++ b/arch/sh/cpu/u-boot.lds @@ -25,6 +25,7 @@ ENTRY(_start) SECTIONS { + . = CONFIG_SYS_TEXT_BASE; reloc_dst = .; PROVIDE (_ftext = .); -- 2.23.0.rc1

1 3

[U-Boot] ARMv7-a NEON optimizations
by Adam Ford 14 Sep '19

14 Sep '19

I was Googling ARM Neon optimizations, and I came across a pay-article written by someone who was talking about optimizing ECC using NEON. I didn't want to buy the article, nor would I understand it, but I was thinking about running some tests on whether or not NEON could be enabled in U-Boot. At least for the OMAP3 boards which have HW detection and SW correction, I was wondering if the enhanced integer math might be useful for increasing NAND flash performance by helping with ECC calculations on board without HW correction. I will admit that I don't know much about the NEON stuff or ECC, but when reading about it from GCC documentation, and it states: "For floating-point and Advanced SIMD (Neon) instructions, the settings of the options -mfloat-abi and -mfpu must also be considered: floating-point and Advanced SIMD instructions will only be used if -mfloat-abi is not set to ‘soft’; and any setting of -mfpu other than ‘auto’ will override the available floating-point and SIMD extension instructions." I looked through the build instructions, and it appears that we use: arch/arm/config.mk:PLATFORM_RELFLAGS += $(call cc-option, -msoft-float) \ I wasn't sure how -msoft-float compares to mfloat-abi, but when I tried to change msoft-float to mhard-float it stopped working. Can someone tell me if/why we still need to hard-code msoft-float? Maybe I am wasting my time, but it seems like if the NEON has the ability to accelerate integers and not just floating points, it seems like there might be some performance enhancements depending on how the math works. I was hoping to run some simple benchmarks, but I cannot even get u-boot or SPL if I play around with the msoft-float, but some platforms disable it. The Zynq platform seems to partially enable this, but it seems like it could be made more generic for any NEON enabled ARM. arch/arm/mach-zynq/Makefile:AFLAGS_lowlevel_init.o := -mfpu=neon adam

1 0

[U-Boot] [PATCH 1/5] pico-imx6ul: Add DWARF baseboard support
by Otavio Salvador 14 Sep '19

14 Sep '19

This add the boot menu option for the DWARF baseboard as well as a specific config file for users which wish to use it as a pre-defined board. Signed-off-by: Otavio Salvador <otavio(a)ossystems.com.br> --- configs/pico-dwarf-imx6ul_defconfig | 64 +++++++++++++++++++++++++++++ include/configs/pico-imx6ul.h | 6 ++- 2 files changed, 68 insertions(+), 2 deletions(-) create mode 100644 configs/pico-dwarf-imx6ul_defconfig diff --git a/configs/pico-dwarf-imx6ul_defconfig b/configs/pico-dwarf-imx6ul_defconfig new file mode 100644 index 0000000000..e7af415abd --- /dev/null +++ b/configs/pico-dwarf-imx6ul_defconfig @@ -0,0 +1,64 @@ +CONFIG_ARM=y +CONFIG_ARCH_MX6=y +CONFIG_SYS_TEXT_BASE=0x87800000 +CONFIG_SPL_GPIO_SUPPORT=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_TARGET_PICO_IMX6UL=y +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL=y +CONFIG_SPL_LIBDISK_SUPPORT=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg" +CONFIG_BOOTDELAY=3 +CONFIG_BOOTCOMMAND="run findfdt; run finduuid; run distro_bootcmd" +CONFIG_DEFAULT_FDT_FILE="imx6ul-pico-dwarf.dtb" +CONFIG_BOUNCE_BUFFER=y +CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_SPL_USB_HOST_SUPPORT=y +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_SDP_SUPPORT=y +CONFIG_CMD_BOOTMENU=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_DFU=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="imx6ul-pico-pi" +CONFIG_ENV_IS_IN_MMC=y +CONFIG_DFU_MMC=y +CONFIG_USB_FUNCTION_FASTBOOT=y +CONFIG_FASTBOOT_BUF_SIZE=0x10000000 +CONFIG_FASTBOOT_FLASH=y +CONFIG_FASTBOOT_FLASH_MMC_DEV=0 +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y +CONFIG_DM_GPIO=y +CONFIG_DM_I2C=y +CONFIG_DM_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_PHYLIB=y +CONFIG_PHY_MICREL=y +CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_IMX6=y +CONFIG_DM_PMIC=y +CONFIG_DM_PMIC_PFUZE100=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_PFUZE100=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_USB=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y diff --git a/include/configs/pico-imx6ul.h b/include/configs/pico-imx6ul.h index cd051bf263..39c83a8c78 100644 --- a/include/configs/pico-imx6ul.h +++ b/include/configs/pico-imx6ul.h @@ -63,9 +63,11 @@ "rootfs part 0 1\0" \ #define BOOTMENU_ENV \ - "bootmenu_0=Boot using PICO-Hobbit baseboard=" \ + "bootmenu_0=Boot using PICO-Dwarf baseboard=" \ + "setenv fdtfile imx6ul-pico-dwarf.dtb\0" \ + "bootmenu_1=Boot using PICO-Hobbit baseboard=" \ "setenv fdtfile imx6ul-pico-hobbit.dtb\0" \ - "bootmenu_1=Boot using PICO-Pi baseboard=" \ + "bootmenu_2=Boot using PICO-Pi baseboard=" \ "setenv fdtfile imx6ul-pico-pi.dtb\0" \ #define CONFIG_SYS_MMC_IMG_LOAD_PART 1 -- 2.23.0

5 13

[U-Boot] [PATCH] pico: Convert to CONFIG_FSL_USDHC
by Fabio Estevam 14 Sep '19

14 Sep '19

The eSDHC config symbol has been converted to CONFIG_FSL_USDHC, so adjust it accordingly in order to fix the build errors: https://travis-ci.org/sbabic/u-boot-imx/jobs/584781580#L1287 Reported-by: Anatolij Gustschin <agust(a)denx.de> Signed-off-by: Fabio Estevam <festevam(a)gmail.com> --- configs/pico-dwarf-imx6ul_defconfig | 2 +- configs/pico-dwarf-imx7d_defconfig | 2 +- configs/pico-nymph-imx7d_defconfig | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) diff --git a/configs/pico-dwarf-imx6ul_defconfig b/configs/pico-dwarf-imx6ul_defconfig index 33bb70bf1f..f1f6506868 100644 --- a/configs/pico-dwarf-imx6ul_defconfig +++ b/configs/pico-dwarf-imx6ul_defconfig @@ -44,7 +44,7 @@ CONFIG_FASTBOOT_CMD_OEM_FORMAT=y CONFIG_DM_GPIO=y CONFIG_DM_I2C=y CONFIG_DM_MMC=y -CONFIG_FSL_ESDHC=y +CONFIG_FSL_USDHC=y CONFIG_PHYLIB=y CONFIG_PHY_MICREL=y CONFIG_MII=y diff --git a/configs/pico-dwarf-imx7d_defconfig b/configs/pico-dwarf-imx7d_defconfig index b8a5fb60ad..3ba7adcc25 100644 --- a/configs/pico-dwarf-imx7d_defconfig +++ b/configs/pico-dwarf-imx7d_defconfig @@ -52,7 +52,7 @@ CONFIG_FASTBOOT_CMD_OEM_FORMAT=y CONFIG_DM_GPIO=y CONFIG_DM_MMC=y CONFIG_SUPPORT_EMMC_BOOT=y -CONFIG_FSL_ESDHC=y +CONFIG_FSL_USDHC=y CONFIG_PHYLIB=y CONFIG_MII=y CONFIG_PINCTRL=y diff --git a/configs/pico-nymph-imx7d_defconfig b/configs/pico-nymph-imx7d_defconfig index b8a5fb60ad..3ba7adcc25 100644 --- a/configs/pico-nymph-imx7d_defconfig +++ b/configs/pico-nymph-imx7d_defconfig @@ -52,7 +52,7 @@ CONFIG_FASTBOOT_CMD_OEM_FORMAT=y CONFIG_DM_GPIO=y CONFIG_DM_MMC=y CONFIG_SUPPORT_EMMC_BOOT=y -CONFIG_FSL_ESDHC=y +CONFIG_FSL_USDHC=y CONFIG_PHYLIB=y CONFIG_MII=y CONFIG_PINCTRL=y -- 2.17.1

1 0

[U-Boot] [PATCH] imx: sksimx6_defconfig: remove SPL misc option to fix build error
by Anatolij Gustschin 14 Sep '19

14 Sep '19

Remove CONFIG_SPL_DRIVERS_MISC_SUPPORT since it is already defined in include/configs/mx6_common.h for SPL builds. When this option is in defconfig, we get build warnings (or errors when building with -Werror). Signed-off-by: Anatolij Gustschin <agust(a)denx.de> --- Hi Stefano, This fixes build breakage seen here: https://travis-ci.org/sbabic/u-boot-imx/jobs/584781580#L1870 Please apply. Thanks! Anatolij configs/sksimx6_defconfig | 1 - 1 file changed, 1 deletion(-) diff --git a/configs/sksimx6_defconfig b/configs/sksimx6_defconfig index 7bc687f64d..7030438f08 100644 --- a/configs/sksimx6_defconfig +++ b/configs/sksimx6_defconfig @@ -8,7 +8,6 @@ CONFIG_MX6_DDRCAL=y CONFIG_TARGET_SKSIMX6=y CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y CONFIG_NR_DRAM_BANKS=1 CONFIG_SPL=y CONFIG_SPL_LIBDISK_SUPPORT=y -- 2.17.1

1 0

[U-Boot] Please pull pico-imx7d-2019.10-1 from https://github.com/OSSystems/u-boot
by Otavio Salvador 14 Sep '19

14 Sep '19

Hello Stefano, The same patches I sent before are also online. See: The following changes since commit 333027284f9a591747ec469ede2b13b3fb8df65a: Merge branch 'nxp-imx-8-13' of https://github.com/MrVan/u-boot (2019-08-18 12:10:11 +0200) are available in the Git repository at: https://github.com/OSSystems/u-boot pico-imx7d-2019.10-1 for you to fetch changes up to 697cc0eaa7104950a52425786c2c830879b044d4: logos: Add the TechNexion's logo (2019-09-12 16:35:59 -0300) ---------------------------------------------------------------- Fabio Berton (1): pico-imx7d: Sync pico-hobbit-imx7d_defconfig Fabio Estevam (3): pico-imx7d: Add instructions for booting in Falcon mode pico-imx7d: Provide a way to escape the Falcon mode logos: Add the TechNexion's logo Otavio Salvador (2): pico-imx7d: Add DWARF baseboard support pico-imx7d: Add NYMPH baseboard support board/technexion/pico-imx7d/README | 91 ++++++++++++++++++++++++++++++++++++ board/technexion/pico-imx7d/spl.c | 4 ++ configs/pico-dwarf-imx7d_defconfig | 68 +++++++++++++++++++++++++++ configs/pico-hobbit-imx7d_defconfig | 2 +- configs/pico-nymph-imx7d_defconfig | 68 +++++++++++++++++++++++++++ include/configs/pico-imx7d.h | 6 ++- tools/logos/technexion.bmp | Bin 0 -> 22390 bytes 7 files changed, 237 insertions(+), 2 deletions(-) create mode 100644 configs/pico-dwarf-imx7d_defconfig create mode 100644 configs/pico-nymph-imx7d_defconfig create mode 100644 tools/logos/technexion.bmp -- Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9 9981-7854 Mobile: +1 (347) 903-9750

3 8

[U-Boot] U-boot Tegra 3
by Saint Alt 14 Sep '19

14 Sep '19

Hi, can you help me to solve problem with u-boot. I have tegra30 board like (180-61852-1606-c00) it’s looks like cardhu one. But when I build(cardhu board) u-boot and run it, I have error when I want to select emmc card. Error: Card did not respond to voltage select! , mmc_init: -95, time 77. Can you help me or give advice how I can initialize this emmc.

1 0