May 2018 - U-Boot

[U-Boot] help on DM
by Andy Tang 17 May '18

17 May '18

Hi Simon, I am working on enabling DM for sata driver. Previously sata was initialized by calling the functions ahci_init() and scsi_scan(). Now I plan to use driver/ata/sata_ceva.c as our sata driver. In board config file I enabled the following configs (dts was added properly): +CONFIG_DM_SCSI=y +CONFIG_SATA_CEVA=y +CONFIG_AHCI=y +CONFIG_BLK=y +CONFIG_SCSI_AHCI=y +CONFIG_SCSI=y But I always got the "Synchronous Abort" error. I tracked the code and found dev->uclass_priv was not allocated properly because dev->uclass->uc_drv->per_device_auto_alloc_size is 0. But I didn't find where I can set per_device_auto_alloc_size or attach a uclass_priv structure to the device. I am new to DM. Could you please give me some suggestions here? Thanks, Andy

2 2

[U-Boot] [PATCH 1/1] efi_loader: avoid using unitialized values as console size
by Heinrich Schuchardt 16 May '18

16 May '18

If a request for the console size would be answered with a response with less then three values, uninitialized stack memory would be copied to the number of rows and columns of the terminal. Signed-off-by: Heinrich Schuchardt <xypron.glpk(a)gmx.de> --- lib/efi_loader/efi_console.c | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-) diff --git a/lib/efi_loader/efi_console.c b/lib/efi_loader/efi_console.c index 5d1a9a8081e..8365431291c 100644 --- a/lib/efi_loader/efi_console.c +++ b/lib/efi_loader/efi_console.c @@ -63,7 +63,15 @@ static struct simple_text_output_mode efi_con_mode = { .cursor_visible = 1, }; -static int term_read_reply(int *n, int maxnum, char end_char) +/* + * Receive and parse a reply from the terminal. + * + * @n: array of return values + * @num: number of return values expected + * @end_char: character indicating end of terminal message + * @return: non-zero indicates error + */ +static int term_read_reply(int *n, int num, char end_char) { char c; int i = 0; @@ -80,7 +88,7 @@ static int term_read_reply(int *n, int maxnum, char end_char) c = getc(); if (c == ';') { i++; - if (i >= maxnum) + if (i >= num) return -1; n[i] = 0; continue; @@ -94,6 +102,8 @@ static int term_read_reply(int *n, int maxnum, char end_char) n[i] *= 10; n[i] += c - '0'; } + if (i != num - 1) + return -1; return 0; } -- 2.14.2

2 1

[U-Boot] [PATCH v4 00/14] Add fastboot UDP support
by Alex Kiernan 16 May '18

16 May '18

This series merges the fastboot UDP support from AOSP into mainline U-Boot. Changes in UDP behaviour from the AOSP code, so it follows the existing USB behaviour: - 'boot' now follows the USB code and does 'bootm CONFIG_FASTBOOT_BUF_ADDR'. I've added 'fastboot_bootcmd' which if set overrides the boot command and allows the existing UDP behaviour to be preserved. - 'continue' in UDP now exits the fastboot server rather than executing 'run bootcmd' - 'reboot-bootloader' no longer writes 'reboot-bootloader' to CONFIG_FASTBOOT_BUF_ADDR as its marker for the subsequent boot. The code which is in AOSP common/android_bootloader.c expects this marker, but we have prior art in the USB code using the weak function fastboot_set_reboot_flag - 'getvar' in the UDP path now supports fetching 'fastboot.' prefixed variables (inherited from the USB path), these override the defaults I'll post the USB migration as a separate patch. Changes in v4: - add docbook comments - leave strcmp_l1() in USB fastboot as we don't need it in UDP path - add docbook comments - new - guard fb_getvar/fb_command with UDP_FUNCTION_FASTBOOT in Makefile - add docbook comments - remove parameter from fastboot_boot() since we always want fastboot_buf_addr (and if we're using fastboot_bootcmd then it's ignored) Changes in v3: - move imply ANDROID_BOOT_IMAGE, CMD_FASTBOOT to FASTBOOT from USB_FUNCTION_FASTBOOT - add depend on USB_FUNCTION_FASTBOOT to FASTBOOT_USB_DEV - leave images-sparse.c in common to acommodate 2f83f21 - move Kconfig changes to previous patch - refactor for changes in master - Merge subsequent patch for formatting response strings into this one - allow NULL to fastboot_okay() when there's no message to send - guard FASTBOOT_GPT_NAME/FASTBOOT_MBR_NAME with EFI/DOS_PARTITION - use FASTBOOT as our guard in Kconfig not a list of USB || UDP - correct mis-translation from AOSP introduced when cleaning up for checkpatch - we should write when buffer is not NULL, rather than erasing, and erase when buffer is NULL - use CMD_RET_USAGE from do_fastboot - remove do_fastboot_udp from cmd/net.c and rewrite using net_loop() - rename timed_send_info to fastboot_send_info, rename fastboot_send_info to fastboot_udp_send_info - replace FASTBOOT_HEADER_SIZE with sizeof(struct fastboot_header) - move start time into timed_send_info() rather than passing it in - make calls to fastboot_udp_send_info a runtime dependency, not a compile time one - set ${filesize} to size of downloaded image - add progress meter from USB path during download - add support for 'oem format' command from the USB path - rename 'fastbootcmd' to 'fastboot_bootcmd' to make clear that this is the fastboot boot command - make getvar implementation table driven - add fastboot_buf_addr, fastboot_buf_size to override buffer address and size - return correct filesystem type in getvar partition-type on MMC - process "fastboot." prefixed env variables in getvar first so you can override the normal values (this also lets you set a fs type for NAND devices) - make global variables static and add accessors for the things which the transport layers need - squash subsequent patches which change this code into this one: - If the fastboot flash/erase commands are disabled, remove that support so we still build correctly. - Add NAND support to fastboot UDP flash/erase commands - If we don't have a partition name passed, report it as not found. - Change the behaviour of the fastboot net code such that "reboot-bootloader" is no longer written to CONFIG_FASTBOOT_BUF_ADDR for use as a marker on reboot (the AOSP code in common/android-bootloader.c uses this marker - this code could be reinstated there if that gets merged). - Merge USB and UDP boot code. The USB implementation stays the same, but UDP no longer passes an fdt. We introduce a new environment variable 'fastboot_bootcmd' which if set overrides the hardcoded boot command, setting this then allows the UDP implementation to remain the same. If after running 'fastboot_bootcmd' the board has not booted, control is returned to U-Boot and the fastboot process ends. - Separate the fastboot protocol handling from the fastboot UDP code in preparation for reusing it in the USB code. Changes in v2: - ensure fastboot syntax is backward compatible - 'fastboot 0' means 'fastboot usb 0' Alex Kiernan (14): fastboot: Move fastboot to drivers/fastboot fastboot: Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT fastboot: Refactor fastboot_okay/fail to take response fastboot: Extract fastboot_okay/fail to fb_common.c fastboot: Correct dependencies in FASTBOOT_FLASH fastboot: Add missing newlines fastboot: Remove FIXME for CONFIG_FASTBOOT_...NAME fastboot: Fix parameter types in _fb_nand_write fastboot: Rename fb_set_reboot_flag to fastboot_set_reboot_flag fastboot: Extract common definitions from USB fastboot ti: fastboot: Move weak overrides to board files fs: Add fs_get_type_name to return current filesystem name mmc: Separate "mmc swrite" from fastboot net: fastboot: Merge AOSP UDP fastboot arch/arm/Kconfig | 2 - arch/arm/mach-omap2/boot-common.c | 10 - arch/arm/mach-omap2/utils.c | 4 +- arch/arm/mach-rockchip/rk3128-board.c | 4 +- arch/arm/mach-rockchip/rk322x-board.c | 4 +- board/amazon/kc1/kc1.c | 2 +- board/lg/sniper/sniper.c | 2 +- board/ti/am57xx/board.c | 10 + board/ti/common/Kconfig | 1 - board/ti/dra7xx/evm.c | 10 + cmd/Kconfig | 22 +- cmd/fastboot.c | 91 ++++++- cmd/mmc.c | 14 +- common/Makefile | 14 - configs/am335x_boneblack_defconfig | 2 +- configs/am335x_boneblack_vboot_defconfig | 2 +- configs/am335x_evm_defconfig | 2 +- configs/am335x_evm_nor_defconfig | 2 +- configs/am335x_evm_norboot_defconfig | 2 +- configs/am335x_evm_spiboot_defconfig | 2 +- configs/am335x_evm_usbspl_defconfig | 2 +- configs/am57xx_evm_defconfig | 2 +- configs/am57xx_hs_evm_defconfig | 2 +- configs/bcm23550_w1d_defconfig | 2 +- configs/bcm28155_ap_defconfig | 2 +- configs/birdland_bav335a_defconfig | 2 +- configs/birdland_bav335b_defconfig | 2 +- configs/cgtqmx6eval_defconfig | 2 +- configs/dra7xx_evm_defconfig | 2 +- configs/dra7xx_hs_evm_defconfig | 2 +- configs/kc1_defconfig | 2 +- configs/mx6qsabrelite_defconfig | 2 +- configs/mx6sabresd_defconfig | 2 +- configs/nitrogen6dl2g_defconfig | 2 +- configs/nitrogen6dl_defconfig | 2 +- configs/nitrogen6q2g_defconfig | 2 +- configs/nitrogen6q_defconfig | 2 +- configs/nitrogen6s1g_defconfig | 2 +- configs/nitrogen6s_defconfig | 2 +- configs/omap3_beagle_defconfig | 2 +- configs/omap3_evm_defconfig | 2 +- configs/omap3_logic_defconfig | 2 +- configs/sniper_defconfig | 2 +- configs/stih410-b2260_defconfig | 2 +- configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 2 +- configs/xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 2 +- configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 2 +- configs/xilinx_zynqmp_zcu102_revA_defconfig | 2 +- configs/xilinx_zynqmp_zcu102_revB_defconfig | 2 +- configs/xilinx_zynqmp_zcu106_revA_defconfig | 2 +- drivers/Kconfig | 2 + drivers/Makefile | 1 + {cmd => drivers}/fastboot/Kconfig | 53 ++-- drivers/fastboot/Makefile | 7 + drivers/fastboot/fb_command.c | 327 +++++++++++++++++++++++ drivers/fastboot/fb_common.c | 190 +++++++++++++ drivers/fastboot/fb_getvar.c | 229 ++++++++++++++++ {common => drivers/fastboot}/fb_mmc.c | 192 ++++++++----- {common => drivers/fastboot}/fb_nand.c | 46 ++-- drivers/usb/gadget/f_fastboot.c | 59 ++-- fs/fs.c | 13 + include/fastboot.h | 167 +++++++++++- include/fb_mmc.h | 10 +- include/fb_nand.h | 12 +- include/fs.h | 10 + include/image-sparse.h | 4 +- include/net.h | 2 +- include/net/fastboot.h | 21 ++ lib/Kconfig | 3 + lib/Makefile | 1 + {common => lib}/image-sparse.c | 32 ++- net/Makefile | 1 + net/fastboot.c | 312 +++++++++++++++++++++ net/net.c | 7 + 74 files changed, 1704 insertions(+), 259 deletions(-) rename {cmd => drivers}/fastboot/Kconfig (83%) create mode 100644 drivers/fastboot/Makefile create mode 100644 drivers/fastboot/fb_command.c create mode 100644 drivers/fastboot/fb_common.c create mode 100644 drivers/fastboot/fb_getvar.c rename {common => drivers/fastboot}/fb_mmc.c (66%) rename {common => drivers/fastboot}/fb_nand.c (81%) create mode 100644 include/net/fastboot.h rename {common => lib}/image-sparse.c (89%) create mode 100644 net/fastboot.c -- 2.7.4

5 31

[U-Boot] spi(u-boot)+MMC(Kernel)
by Mehmet Ali İPİN 16 May '18

16 May '18

Dear Fabio, Thank you for your all helps very much. I had our mx6dl board boot from SPI flash. Now I wish to boot kernel from eMMC flash. I am studying warp board's config parameters. Do you now a (i.mx6) product which has similar (SPI+eMMC) boot configuration, which I can modify my u-boot environment parameters accordingly? Do you know a link of tutorial or a document which explains these parameters? Thanks and best regards.

2 1

[U-Boot] [PATCH] rockchip: make_fit_atf: use elf entry point
by Mian Yousaf Kaukab 16 May '18

16 May '18

make_fit_atf.py uses physical address of first segment as the entry point to bl31. It is incorrect and causes following abort when bl31_entry() is called: U-Boot SPL board initTrying to boot from MMC1 "Synchronous Abort" handler, esr 0x02000000 elr: 0000000000000000 lr : 00000000ff8c7e8c x 0: 00000000ff8e0000 x 1: 0000000000000000 x 2: 0000000000000000 x 3: 00000000ff8e0180 x 4: 0000000000000000 x 5: 0000000000000000 x 6: 0000000000000030 x 7: 00000000ff8e0188 x 8: 00000000000001e0 x 9: 0000000000000000 x10: 000000000007fcdc x11: 00000000002881b8 x12: 00000000000001a2 x13: 0000000000000198 x14: 000000000007fdcc x15: 00000000002881b8 x16: 00000000003c0724 x17: 00000000003c0718 x18: 000000000007fe80 x19: 00000000ff8e0000 x20: 0000000000200000 x21: 00000000ff8e0000 x22: 0000000000000000 x23: 000000000007fe30 x24: 00000000ff8d1c3c x25: 00000000ff8d5000 x26: 00000000deadbeef x27: 00000000000004a0 x28: 000000000000009c x29: 000000000007fd90 Fix it by using the entry point from the elf header. Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab(a)suse.com> --- arch/arm/mach-rockchip/make_fit_atf.py | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/arch/arm/mach-rockchip/make_fit_atf.py b/arch/arm/mach-rockchip/make_fit_atf.py index 6b3d9201c9..b88a5e1f16 100755 --- a/arch/arm/mach-rockchip/make_fit_atf.py +++ b/arch/arm/mach-rockchip/make_fit_atf.py @@ -53,7 +53,7 @@ DT_END=""" }; """ -def append_atf_node(file, atf_index, phy_addr): +def append_atf_node(file, atf_index, phy_addr, elf_entry): """ Append ATF DT node to input FIT dts file. """ @@ -67,7 +67,7 @@ def append_atf_node(file, atf_index, phy_addr): print >> file, '\t\t\tcompression = "none";' print >> file, '\t\t\tload = <0x%08x>;' % phy_addr if atf_index == 1: - print >> file, '\t\t\tentry = <0x%08x>;' % phy_addr + print >> file, '\t\t\tentry = <0x%08x>;' % elf_entry print >> file, '\t\t};' print >> file, '' @@ -141,12 +141,13 @@ def generate_atf_fit_dts(fit_file_name, bl31_file_name, uboot_file_name, dtbs_fi with open(bl31_file_name) as bl31_file: bl31 = ELFFile(bl31_file) + elf_entry = bl31.header['e_entry'] for i in range(bl31.num_segments()): seg = bl31.get_segment(i) if ('PT_LOAD' == seg.__getitem__(ELF_SEG_P_TYPE)): paddr = seg.__getitem__(ELF_SEG_P_PADDR) p= seg.__getitem__(ELF_SEG_P_PADDR) - append_atf_node(fit_file, i+1, paddr) + append_atf_node(fit_file, i+1, paddr, elf_entry) atf_cnt = i+1 append_fdt_node(fit_file, dtbs_file_name) print >> fit_file, '%s' % DT_IMAGES_NODE_END -- 2.11.0

1 0

[U-Boot] [PATCH v1 00/21] This patch series brings in sync DISPLAY5 internal
by Lukasz Majewski 16 May '18

16 May '18

This patch series brings the internal DISPLAY5 development in sync with mainline. Lukasz Majewski (21): display5: factory: Add support for BOOT_FROM = FACTORY switch display5: config: factory: Setup IP config data according to LEG production setup display5: config: Add "factory" (1MiB) SPI-NOR partition in u-boot display5: config: Provide command to flash the whole SPI-NOR memory display5: spl: Check return code of the env_* functions display5: config: Reset the board when bootm fails display5: config: Remove support for Linux initramfs recovery image boot display5: config: Update SPI-NOR partition for larger swupdate-initramfs display5: config: factory: Extend mtdparts to support LEG factory partition display5: Support for the emergency PAD pressing display5: wdt: Enable WDT support (both SPL and u-boot) display5: config: Provide 'tftp_mmc_rootfs_bkp' command to write BACKUP rootfs display5: config: factory: Update BACKUP rootfs in factory mode display5: config: Update swupdate initramfs file name (now supporting ext4) display5: ddr: Enable support for DDR3 auto calibration display5: net: Add function to read ethaddr from iMX6 fuses display5: config: Add cma=256M to command line arguments display5: config: Reduce rootfs2 (BACKUP) size from 1528M to 512M display5: display5_defconfig: Enable support for gpt command (CMD_GPT) in production u-boot display5: config: Add GPT verification and restoration code on SWUpdate entry display5: Add missing environment.h include to avoid warning board/liebherr/display5/common.c | 10 ++++ board/liebherr/display5/common.h | 1 + board/liebherr/display5/display5.c | 41 +++++++++++++++ board/liebherr/display5/spl.c | 78 +++++++++++++++++++++++++++- configs/display5_defconfig | 6 ++- configs/display5_factory_defconfig | 3 +- include/configs/display5.h | 102 ++++++++++++++++++++++--------------- 7 files changed, 194 insertions(+), 47 deletions(-) -- 2.11.0

2 24

[U-Boot] [PATCH 0/8] Initial integration of AVB2.0
by Igor Opaniuk 16 May '18

16 May '18

This series of patches introduces support of Android Verified Boot 2.0, which provides integrity checking of Android partitions on MMC. It integrates libavb/libavb_ab into the U-boot, provides implementation of AvbOps, subset of `avb` commands to run verification chain (and for debugging purposes), and it enables AVB2.0 verification on AM57xx HS SoC by default. Currently, there is still no support for verification of A/B boot slots and no rollback protection (for storing rollback indexes there are plans to use eMMC RPMB) Libavb/libavb_ab will be deviated from AOSP upstream in the future, that's why minimal amount of changes were introduced into the lib sources, so checkpatch may fail. For additional details check [1] AVB 2.0 README and doc/README.avb2, which is a part of this patchset. [1] https://android.googlesource.com/platform/external/avb/+/master/README.md Igor Opaniuk (8): avb2.0: add Android Verified Boot 2.0 libraries avb2.0: integrate avb 2.0 into the build system avb2.0: implement AVB ops cmd: avb2.0: avb command for performing verification avb2.0: add boot states and dm-verity support am57xx_hs: avb2.0: add support of AVB 2.0 test/py: avb2.0: add tests for avb commands doc: avb2.0: add README about AVB2.0 integration cmd/Kconfig | 15 + cmd/Makefile | 3 + cmd/avb.c | 366 ++++++++ common/Makefile | 2 + common/avb_verify.c | 748 ++++++++++++++++ configs/am57xx_hs_evm_defconfig | 3 + doc/README.avb2 | 100 +++ include/avb/avb_ab_flow.h | 235 ++++++ include/avb/avb_ab_ops.h | 61 ++ include/avb/avb_chain_partition_descriptor.h | 54 ++ include/avb/avb_crypto.h | 147 ++++ include/avb/avb_descriptor.h | 113 +++ include/avb/avb_footer.h | 68 ++ include/avb/avb_hash_descriptor.h | 55 ++ include/avb/avb_hashtree_descriptor.h | 65 ++ include/avb/avb_kernel_cmdline_descriptor.h | 63 ++ include/avb/avb_ops.h | 196 +++++ include/avb/avb_property_descriptor.h | 89 ++ include/avb/avb_rsa.h | 55 ++ include/avb/avb_sha.h | 72 ++ include/avb/avb_slot_verify.h | 239 ++++++ include/avb/avb_sysdeps.h | 97 +++ include/avb/avb_util.h | 259 ++++++ include/avb/avb_vbmeta_image.h | 272 ++++++ include/avb/avb_version.h | 45 + include/avb/libavb.h | 32 + include/avb/libavb_ab.h | 22 + include/avb_verify.h | 97 +++ include/configs/am57xx_evm.h | 11 + include/environment/ti/boot.h | 15 + lib/Kconfig | 20 + lib/Makefile | 2 + lib/libavb/Makefile | 15 + lib/libavb/avb_chain_partition_descriptor.c | 46 + lib/libavb/avb_crypto.c | 355 ++++++++ lib/libavb/avb_descriptor.c | 142 ++++ lib/libavb/avb_footer.c | 36 + lib/libavb/avb_hash_descriptor.c | 43 + lib/libavb/avb_hashtree_descriptor.c | 51 ++ lib/libavb/avb_kernel_cmdline_descriptor.c | 40 + lib/libavb/avb_property_descriptor.c | 167 ++++ lib/libavb/avb_rsa.c | 277 ++++++ lib/libavb/avb_sha256.c | 364 ++++++++ lib/libavb/avb_sha512.c | 362 ++++++++ lib/libavb/avb_slot_verify.c | 1169 ++++++++++++++++++++++++++ lib/libavb/avb_sysdeps_posix.c | 57 ++ lib/libavb/avb_util.c | 385 +++++++++ lib/libavb/avb_vbmeta_image.c | 290 +++++++ lib/libavb/avb_version.c | 16 + lib/libavb_ab/Makefile | 9 + lib/libavb_ab/avb_ab_flow.c | 502 +++++++++++ test/py/tests/test_avb.py | 111 +++ 52 files changed, 8058 insertions(+) create mode 100644 cmd/avb.c create mode 100644 common/avb_verify.c create mode 100644 doc/README.avb2 create mode 100644 include/avb/avb_ab_flow.h create mode 100644 include/avb/avb_ab_ops.h create mode 100644 include/avb/avb_chain_partition_descriptor.h create mode 100644 include/avb/avb_crypto.h create mode 100644 include/avb/avb_descriptor.h create mode 100644 include/avb/avb_footer.h create mode 100644 include/avb/avb_hash_descriptor.h create mode 100644 include/avb/avb_hashtree_descriptor.h create mode 100644 include/avb/avb_kernel_cmdline_descriptor.h create mode 100644 include/avb/avb_ops.h create mode 100644 include/avb/avb_property_descriptor.h create mode 100644 include/avb/avb_rsa.h create mode 100644 include/avb/avb_sha.h create mode 100644 include/avb/avb_slot_verify.h create mode 100644 include/avb/avb_sysdeps.h create mode 100644 include/avb/avb_util.h create mode 100644 include/avb/avb_vbmeta_image.h create mode 100644 include/avb/avb_version.h create mode 100644 include/avb/libavb.h create mode 100644 include/avb/libavb_ab.h create mode 100644 include/avb_verify.h create mode 100644 lib/libavb/Makefile create mode 100644 lib/libavb/avb_chain_partition_descriptor.c create mode 100644 lib/libavb/avb_crypto.c create mode 100644 lib/libavb/avb_descriptor.c create mode 100644 lib/libavb/avb_footer.c create mode 100644 lib/libavb/avb_hash_descriptor.c create mode 100644 lib/libavb/avb_hashtree_descriptor.c create mode 100644 lib/libavb/avb_kernel_cmdline_descriptor.c create mode 100644 lib/libavb/avb_property_descriptor.c create mode 100644 lib/libavb/avb_rsa.c create mode 100644 lib/libavb/avb_sha256.c create mode 100644 lib/libavb/avb_sha512.c create mode 100644 lib/libavb/avb_slot_verify.c create mode 100644 lib/libavb/avb_sysdeps_posix.c create mode 100644 lib/libavb/avb_util.c create mode 100644 lib/libavb/avb_vbmeta_image.c create mode 100644 lib/libavb/avb_version.c create mode 100644 lib/libavb_ab/Makefile create mode 100644 lib/libavb_ab/avb_ab_flow.c create mode 100644 test/py/tests/test_avb.py -- 2.7.4

7 29

[U-Boot] [PATCH v3 00/21] efi: Enable basic sandbox support for EFI loader
by Simon Glass 16 May '18

16 May '18

A limitation of the EFI loader at present is that it does not build with sandbox. This makes it hard to write tests, since sandbox is used for most testing in U-Boot. This series enables the EFI loader feature. It allows sandbox to build and run a trivial function which calls the EFI API to output a message. This series is at u-boot-dm/efi-working Changes in v3: - Add new patch to init the 'rows' and 'cols' variables - Return error value of efi_allocate_pages() - Update function comment for write_smbios_table() - Add comments on aligment - Avoid adding a new call to efi_init_obj_list() - Fix spelling of initalized - Drop incorrect map_sysmem() in map_sysmem() - Init the 'rows' and 'cols' vars to avoid a compiler error (gcc 4.8.4) - Add new patch to split out test init/uninit into functions - Rebase to master - Add new patch to reorder code in do_bootefi_exec() - Add patch to create a function to set up for running EFI code - Add new patch to rename bootefi_test_finish() to bootefi_run_finish() Changes in v2: - Update return type of efi_smbios_register() to efi_status_t - Use return value of efi_install_configuration_table - Change return type of efi_init_obj_list() to efi_status_t - Convert #ifdef CONFIG_GENERATE_SMBIOS_TABLE to if() - Update commit message to dropping libfdt_env.h - Update to use mapmem instead of a cast - Rebase to master Simon Glass (21): efi: Init the 'rows' and 'cols' variables efi: Update efi_smbios_register() to return error code efi: Move the init check inside efi_init_obj_list() efi: Add error checking for efi_init_obj_list() efi: Add a TODO to efi_init_obj_list() efi: Correct header order in efi_memory efi: sandbox: Adjust memory usage for sandbox sandbox: smbios: Update to support sandbox sandbox: Add a setjmp() implementation efi: sandbox: Add required linker sections efi: sandbox: Add distroboot support Define board_quiesce_devices() in a shared location Add a comment for board_quiesce_devices() efi: sandbox: Add relocation constants efi: Add a comment about duplicated ELF constants efi: sandbox: Enable EFI loader builder for sandbox efi: Split out test init/uninit into functions efi: sandbox: Add a simple 'bootefi test' command efi: Reorder code in do_bootefi_exec() efi: Create a function to set up for running EFI code efi: Rename bootefi_test_finish() to bootefi_run_finish() arch/arm/include/asm/u-boot-arm.h | 1 - arch/sandbox/cpu/cpu.c | 13 ++ arch/sandbox/cpu/os.c | 17 +++ arch/sandbox/cpu/u-boot.lds | 29 +++++ arch/sandbox/include/asm/setjmp.h | 21 ++++ arch/sandbox/lib/Makefile | 2 +- arch/sandbox/lib/sections.c | 12 ++ arch/x86/include/asm/u-boot-x86.h | 1 - arch/x86/lib/bootm.c | 4 - cmd/bootefi.c | 203 +++++++++++++++++++----------- common/bootm.c | 4 + include/bootm.h | 8 ++ include/config_distro_bootcmd.h | 2 +- include/efi_loader.h | 12 +- include/os.h | 21 ++++ include/smbios.h | 5 +- lib/efi_loader/Kconfig | 12 +- lib/efi_loader/Makefile | 1 + lib/efi_loader/efi_console.c | 2 +- lib/efi_loader/efi_memory.c | 36 +++--- lib/efi_loader/efi_runtime.c | 7 ++ lib/efi_loader/efi_smbios.c | 18 ++- lib/efi_loader/efi_test.c | 17 +++ lib/smbios.c | 32 +++-- 24 files changed, 367 insertions(+), 113 deletions(-) create mode 100644 arch/sandbox/include/asm/setjmp.h create mode 100644 arch/sandbox/lib/sections.c create mode 100644 lib/efi_loader/efi_test.c -- 2.16.1.291.g4437f3f132-goog

3 38

[U-Boot] [PATCH 1/2] sandbox: Correct dtc warning in /chosen node
by Simon Glass 16 May '18

16 May '18

At present dtc produces these warnings when compiling sandbox: arch/sandbox/dts/test.dtb: Warning (reg_format): "reg" property in /chosen/chosen-test has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1) arch/sandbox/dts/test.dtb: Warning (avoid_default_addr_size): Relying on default #address-cells value for /chosen/chosen-test arch/sandbox/dts/test.dtb: Warning (avoid_default_addr_size): Relying on default #size-cells value for /chosen/chosen-test Add the missing properties to avoid this. Signed-off-by: Simon Glass <sjg(a)chromium.org> Fixes: f200680 (dm: core: parse chosen node) --- arch/sandbox/dts/test.dts | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/sandbox/dts/test.dts b/arch/sandbox/dts/test.dts index 3f9e788e6c3..c38e3691628 100644 --- a/arch/sandbox/dts/test.dts +++ b/arch/sandbox/dts/test.dts @@ -480,6 +480,8 @@ }; chosen { + #address-cells = <1>; + #size-cells = <1>; chosen-test { compatible = "denx,u-boot-fdt-test"; reg = <9 1>; -- 2.16.0.rc1.238.g530d649a79-goog

1 2

[U-Boot] [PATCH] ARM: re-enable MVGBE for edminiv2
by Chris Packham 16 May '18

16 May '18

This was unintentionally disabled when moving MVGBE to Kconfig. Fixes: commit ed52ea507f12 ("net: add Kconfig for MVGBE") Signed-off-by: Chris Packham <judge.packham(a)gmail.com> --- configs/edminiv2_defconfig | 2 ++ 1 file changed, 2 insertions(+) diff --git a/configs/edminiv2_defconfig b/configs/edminiv2_defconfig index 1ad1fb779030..5abf81dedd98 100644 --- a/configs/edminiv2_defconfig +++ b/configs/edminiv2_defconfig @@ -26,6 +26,8 @@ CONFIG_ENV_IS_IN_FLASH=y CONFIG_MVSATA_IDE=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y +CONFIG_NETDEVICES=y +CONFIG_MVGBE=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_USB_EHCI_HCD=y -- 2.17.0

2 1