March 2014 - U-Boot

[U-Boot] [PATCH 0/6] Adjust command macros to allow smaller U-Boot size
by Simon Glass 31 Mar '14

31 Mar '14

A large chunk of U-Boot's executable size is the code to process and execute commands. This is reasonable, since commands and scripts are an important part of U-Boot's feature set and provide much of its flexibility. However, for some applications only a very limited set of commands is required. Where image size is important, it is desirable to be able to easily remove unwanted code. This series introduces a new board_run_command() function which can be used to run a small subset of commands as required by the board (typically load and bootm), thus allowing the rest of the commands to be automatically and reliably dropped from the image using toolchain dead code elimination. Tests on snow (ARMv7) show this reduces image size dramatically, more than just undefining all the commands: text data bss dec hex filename before: 356359 12550 300056 668965 a3525 b/snow/u-boot with all commands undefined: 155336 5402 8624 169362 29592 b/snow/u-boot with this series: 123177 2958 1544 127679 1f2bf b/snow/u-boot The difference is more pronounced the more effort is put into reducing the image size. For example, removing additional subsystem options yields: text data bss dec hex filename with all commands undefined and most subsystems: 86479 4186 7480 98145 17f61 b/snow/u-boot with this series: 52395 1818 228 54441 d4a9 b/snow/u-boot Further, it is possible to enable some of the split-use options like CONFIG_CMD_USB, and get USB support without the unwanted command overhead (it would be better if USB had a separate option for the command and the USB stack, but that is not the case, and a few other features have a similar problem). U-Boot can then become a really minimal boot loader, with only the required functions available. Simply undefining various unwanted commands in the board config is not as effective, and is much more time-consuming to figure out. Apart from the cost of the parsing code, the commands necessarily provide a lot options and features which are not required by many boards. In particular, with this series, it is possible to run a minimal U-Boot within the SRAM of a modern SoC, providing the benefits of the full U-Boot environment with the small size of SPL. This helps to bridge the gap somewhat. A key difference between U-Boot and SPL is the inclusion of the command parser, and this small size of SPL is a key reason why some boards currently use 'falcon mode', where only SPL is used to boot a kernel. This series has a fairly small impact on the source code, changing command.h and a fairly small change to each list of subcommands (there are about 19 such sites in U-Boot). Note: some effort was expended in trying to obtain the same result with just linker code elimination. However this did not work, since the linker would not eliminate some transitively-called functions like do_fdt() even when callers are removed. Simon Glass (6): Add an info word to commands Refactor command macros so they can compile to nothing Add CONFIG_CMDLINE to allow removal of all commands main: Exclude getline code when CONFIG_CMDLINE is not defined main: Process FDT options even without CONFIG_BOOTDELAY sandbox: Add board_run_command() function README | 8 +++ arch/x86/cpu/u-boot.lds | 4 ++ board/inka4x0/inkadiag.c | 12 ++-- board/intercontrol/digsy_mtc/cmd_mtc.c | 20 +++---- board/sandbox/sandbox/sandbox.c | 10 ++++ common/cmd_bmp.c | 8 +-- common/cmd_bootm.c | 39 ++++++++----- common/cmd_bootstage.c | 10 ++-- common/cmd_cbfs.c | 3 +- common/cmd_clk.c | 6 +- common/cmd_demo.c | 10 ++-- common/cmd_help.c | 4 ++ common/cmd_i2c.c | 34 +++++------ common/cmd_nvedit.c | 42 +++++++------- common/cmd_onenand.c | 23 ++++---- common/cmd_pxe.c | 6 +- common/cmd_sandbox.c | 14 ++--- common/cmd_sound.c | 8 +-- common/cmd_spl.c | 14 ++--- common/cmd_tpm.c | 52 ++++++++--------- common/command.c | 12 +++- common/main.c | 101 ++++++++++++++++++++++---------- drivers/gpio/pca953x.c | 14 ++--- drivers/gpio/tca642x.c | 14 ++--- drivers/misc/ds4510.c | 24 ++++---- include/command.h | 102 ++++++++++++++++++++++++++++----- include/config_defaults.h | 2 + include/config_fallbacks.h | 7 +++ test/dm/cmd_dm.c | 10 ++-- 29 files changed, 392 insertions(+), 221 deletions(-) -- 1.9.1.423.g4596e3a

2 10

Re: [U-Boot] [PATCH 1/1] TPM: STMicroelectronics u-boot driver I2C
by Simon Glass 31 Mar '14

31 Mar '14

Hi Jean-Luc, On 31 March 2014 02:44, Jean-Luc BLANC <jean-luc.blanc(a)st.com> wrote: > Hi Simon, > > I rewrote the patch. A complete different version will be pushed soon. > Sounds good, thanks. Please cc me when you are ready. Regards, Simon

1 0

[U-Boot] u-boot does not build when lensfun is installed on host system
by Alexander Stein 31 Mar '14

31 Mar '14

Hello, u-boot is not compilable when lensfun is isntalled on the host system. The package manager descrption says "lensfun: A library for rectifying and simulating photographic lens distortions". It seems that this caused by using -idirafter instead of -I. Any idea how to fix that? Best regards, Alexander Here are my step: {/tmp} % git clone git://git.denx.de/u-boot.git Cloning into 'u-boot'... remote: Counting objects: 252184, done. remote: Compressing objects: 100% (48664/48664), done. remote: Total 252184 (delta 202282), reused 248994 (delta 199296) Receiving objects: 100% (252184/252184), 60.77 MiB | 665.00 KiB/s, done. Resolving deltas: 100% (202282/202282), done. Checking connectivity... done git clone git://git.denx.de/u-boot.git 10.14s user 2.07s system 10% cpu 1:53.47 total {/tmp} % cd u-boot {master u-boot} % git describe v2014.04-rc2-96-gb4722fe {master u-boot} % CROSS_COMPILE=/opt/OSELAS.Toolchain-2013.12.1/arm-v5te-linux-gnueabi/gcc-4.8.2-glibc-2.18-binutils-2.24-kernel-3.12-sanitized/bin/arm-v5te-linux-gnueabi- make at91sam9263ek_norflash_config Configuring for at91sam9263ek_norflash - Board: at91sam9263ek, Options: AT91SAM9263,SYS_USE_NORFLASH {master u-boot} % CROSS_COMPILE=/opt/OSELAS.Toolchain-2013.12.1/arm-v5te-linux-gnueabi/gcc-4.8.2-glibc-2.18-binutils-2.24-kernel-3.12-sanitized/bin/arm-v5te-linux-gnueabi- make GEN include/autoconf.mk.dep GEN include/autoconf.mk CHK include/config/uboot.release UPD include/config/uboot.release CHK include/generated/version_autogenerated.h UPD include/generated/version_autogenerated.h CHK include/generated/timestamp_autogenerated.h UPD include/generated/timestamp_autogenerated.h HOSTCC scripts/basic/fixdep CC lib/asm-offsets.s GEN include/generated/generic-asm-offsets.h CC arch/arm/lib/asm-offsets.s GEN include/generated/asm-offsets.h HOSTCC tools/bmp_logo HOSTCC tools/aisimage.o In file included from /usr/include/image.h:22:0, from tools/aisimage.c:10: /usr/include/rgbpixel.h:61:3: error: expected specifier-qualifier-list before 'RGBpixel' In file included from tools/aisimage.c:10:0: /usr/include/image.h:40:1: error: unknown type name 'class' /usr/include/image.h:41:1: error: expected '=', ',', ';', 'asm' or '__attribute__' before '{' token tools/aisimage.c:22:1: error: unknown type name 'table_entry_t' tools/aisimage.c:23:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:23:2: warning: (near initialization for 'aisimage_cmds[0]') [enabled by default] tools/aisimage.c:23:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:23:2: warning: (near initialization for 'aisimage_cmds[0]') [enabled by default] tools/aisimage.c:23:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:23:2: warning: (near initialization for 'aisimage_cmds[0]') [enabled by default] tools/aisimage.c:24:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:24:2: warning: (near initialization for 'aisimage_cmds[1]') [enabled by default] tools/aisimage.c:24:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:24:2: warning: (near initialization for 'aisimage_cmds[1]') [enabled by default] tools/aisimage.c:24:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:24:2: warning: (near initialization for 'aisimage_cmds[1]') [enabled by default] tools/aisimage.c:25:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:25:2: warning: (near initialization for 'aisimage_cmds[2]') [enabled by default] tools/aisimage.c:25:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:25:2: warning: (near initialization for 'aisimage_cmds[2]') [enabled by default] tools/aisimage.c:25:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:25:2: warning: (near initialization for 'aisimage_cmds[2]') [enabled by default] tools/aisimage.c:26:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:26:2: warning: (near initialization for 'aisimage_cmds[3]') [enabled by default] tools/aisimage.c:26:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:26:2: warning: (near initialization for 'aisimage_cmds[3]') [enabled by default] tools/aisimage.c:26:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:26:2: warning: (near initialization for 'aisimage_cmds[3]') [enabled by default] tools/aisimage.c:27:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:27:2: warning: (near initialization for 'aisimage_cmds[4]') [enabled by default] tools/aisimage.c:27:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:27:2: warning: (near initialization for 'aisimage_cmds[4]') [enabled by default] tools/aisimage.c:27:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:27:2: warning: (near initialization for 'aisimage_cmds[4]') [enabled by default] tools/aisimage.c:28:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:28:2: warning: (near initialization for 'aisimage_cmds[5]') [enabled by default] tools/aisimage.c:28:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:28:2: warning: (near initialization for 'aisimage_cmds[5]') [enabled by default] tools/aisimage.c:28:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:28:2: warning: (near initialization for 'aisimage_cmds[5]') [enabled by default] tools/aisimage.c:29:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:29:2: warning: (near initialization for 'aisimage_cmds[6]') [enabled by default] tools/aisimage.c:29:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:29:2: warning: (near initialization for 'aisimage_cmds[6]') [enabled by default] tools/aisimage.c:29:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:29:2: warning: (near initialization for 'aisimage_cmds[6]') [enabled by default] tools/aisimage.c:30:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:30:2: warning: (near initialization for 'aisimage_cmds[7]') [enabled by default] tools/aisimage.c:30:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:30:2: warning: (near initialization for 'aisimage_cmds[7]') [enabled by default] tools/aisimage.c:30:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:30:2: warning: (near initialization for 'aisimage_cmds[7]') [enabled by default] tools/aisimage.c:31:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:31:2: warning: (near initialization for 'aisimage_cmds[8]') [enabled by default] tools/aisimage.c:31:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:31:2: warning: (near initialization for 'aisimage_cmds[8]') [enabled by default] tools/aisimage.c:31:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:31:2: warning: (near initialization for 'aisimage_cmds[8]') [enabled by default] tools/aisimage.c:32:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:32:2: warning: (near initialization for 'aisimage_cmds[9]') [enabled by default] tools/aisimage.c:32:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:32:2: warning: (near initialization for 'aisimage_cmds[9]') [enabled by default] tools/aisimage.c:32:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:32:2: warning: (near initialization for 'aisimage_cmds[9]') [enabled by default] tools/aisimage.c:33:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:33:2: warning: (near initialization for 'aisimage_cmds[10]') [enabled by default] tools/aisimage.c:33:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:33:2: warning: (near initialization for 'aisimage_cmds[10]') [enabled by default] tools/aisimage.c:33:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:33:2: warning: (near initialization for 'aisimage_cmds[10]') [enabled by default] tools/aisimage.c:34:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:34:2: warning: (near initialization for 'aisimage_cmds[11]') [enabled by default] tools/aisimage.c:34:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:34:2: warning: (near initialization for 'aisimage_cmds[11]') [enabled by default] tools/aisimage.c:34:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:34:2: warning: (near initialization for 'aisimage_cmds[11]') [enabled by default] tools/aisimage.c:35:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:35:2: warning: (near initialization for 'aisimage_cmds[12]') [enabled by default] tools/aisimage.c:35:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:35:2: warning: (near initialization for 'aisimage_cmds[12]') [enabled by default] tools/aisimage.c:35:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:35:2: warning: (near initialization for 'aisimage_cmds[12]') [enabled by default] tools/aisimage.c:36:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:36:2: warning: (near initialization for 'aisimage_cmds[13]') [enabled by default] tools/aisimage.c:36:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:36:2: warning: (near initialization for 'aisimage_cmds[13]') [enabled by default] tools/aisimage.c:36:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:36:2: warning: (near initialization for 'aisimage_cmds[13]') [enabled by default] tools/aisimage.c:37:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:37:2: warning: (near initialization for 'aisimage_cmds[14]') [enabled by default] tools/aisimage.c:37:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:37:2: warning: (near initialization for 'aisimage_cmds[14]') [enabled by default] tools/aisimage.c:37:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:37:2: warning: (near initialization for 'aisimage_cmds[14]') [enabled by default] tools/aisimage.c:38:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:38:2: warning: (near initialization for 'aisimage_cmds[15]') [enabled by default] tools/aisimage.c:38:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:38:2: warning: (near initialization for 'aisimage_cmds[15]') [enabled by default] tools/aisimage.c:38:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:38:2: warning: (near initialization for 'aisimage_cmds[15]') [enabled by default] tools/aisimage.c:39:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:39:2: warning: (near initialization for 'aisimage_cmds[16]') [enabled by default] tools/aisimage.c:39:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:39:2: warning: (near initialization for 'aisimage_cmds[16]') [enabled by default] tools/aisimage.c:39:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:39:2: warning: (near initialization for 'aisimage_cmds[16]') [enabled by default] tools/aisimage.c:40:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:40:2: warning: (near initialization for 'aisimage_cmds[17]') [enabled by default] tools/aisimage.c:40:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:40:2: warning: (near initialization for 'aisimage_cmds[17]') [enabled by default] tools/aisimage.c:40:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:40:2: warning: (near initialization for 'aisimage_cmds[17]') [enabled by default] tools/aisimage.c:41:2: warning: braces around scalar initializer [enabled by default] tools/aisimage.c:41:2: warning: (near initialization for 'aisimage_cmds[18]') [enabled by default] tools/aisimage.c:41:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:41:2: warning: (near initialization for 'aisimage_cmds[18]') [enabled by default] tools/aisimage.c:41:2: warning: excess elements in scalar initializer [enabled by default] tools/aisimage.c:41:2: warning: (near initialization for 'aisimage_cmds[18]') [enabled by default] tools/aisimage.c: In function 'aisimage_print_header': tools/aisimage.c:151:4: warning: implicit declaration of function 'get_table_entry_name' [-Wimplicit-function-declaration] tools/aisimage.c:151:4: warning: format '%s' expects argument of type 'char *', but argument 3 has type 'int' [-Wformat] tools/aisimage.c: In function 'aisimage_generate': tools/aisimage.c:317:5: warning: implicit declaration of function 'get_table_entry_id' [-Wimplicit-function-declaration] tools/aisimage.c:335:25: error: request for member 'sname' in something not a structure or union tools/aisimage.c: In function 'aisimage_check_image_types': tools/aisimage.c:366:14: error: 'IH_TYPE_AISIMAGE' undeclared (first use in this function) tools/aisimage.c:366:14: note: each undeclared identifier is reported only once for each function it appears in tools/aisimage.c:370:1: warning: control reaches end of non-void function [-Wreturn-type] make[1]: *** [tools/aisimage.o] Error 1 make: *** [tools] Error 2 -- Dipl.-Inf. Alexander Stein SYS TEC electronic GmbH Am Windrad 2 08468 Heinsdorfergrund Tel.: 03765 38600-1156 Fax: 03765 38600-4100 Email: alexander.stein(a)systec-electronic.com Website: www.systec-electronic.com Managing Director: Dipl.-Phys. Siegmar Schmidt Commercial registry: Amtsgericht Chemnitz, HRB 28082

1 0

[U-Boot] [PATCH] Kbuild: allow building tools without board configuration
by Masahiro Yamada 31 Mar '14

31 Mar '14

Prior to Kbuild, U-Boot could build under tools/ directory withour configuring for a specific board. That feature was lost when switching to Kbuild. This patch revives it again by adding a make target "tools-only". Usage: $ make tools-only Neither board configuration nor cross compiler are required to build host tools. Signed-off-by: Masahiro Yamada <yamada.m(a)jp.panasonic.com> Suggested-by: Alexey Brodkin <Alexey.Brodkin(a)synopsys.com> Cc: Alexey Brodkin <Alexey.Brodkin(a)synopsys.com> Cc: Simon Glass <sjg(a)chromium.org> Cc: Tom Rini <trini(a)ti.com> --- Makefile | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/Makefile b/Makefile index e5f5a8c..43391eb 100644 --- a/Makefile +++ b/Makefile @@ -409,7 +409,7 @@ timestamp_h := include/generated/timestamp_autogenerated.h no-dot-config-targets := clean clobber mrproper distclean \ help %docs check% coccicheck \ - ubootversion backup + ubootversion backup tools-only config-targets := 0 mixed-targets := 0 @@ -1128,6 +1128,9 @@ checkarmreloc: u-boot env: scripts_basic $(Q)$(MAKE) $(build)=tools/$@ +tools-only: scripts_basic $(version_h) $(timestamp_h) + $(Q)$(MAKE) $(build)=tools + tools-all: export HOST_TOOLS_ALL=y tools-all: env tools ; -- 1.8.3.2

3 7

[U-Boot] [PATCH] tegra: fix Makefile to pass per-file CFLAGS
by Masahiro Yamada 31 Mar '14

31 Mar '14

Since Kbuild was introduced, warmboot_avp.o has been compiled without -march=armv4t. Makefile should be adjusted to pass a per-file option. Signed-off-by: Masahiro Yamada <yamada.m(a)jp.panasonic.com> Cc: Stephen Warren <swarren(a)nvidia.com> Cc: Tom Warren <twarren(a)nvidia.com> --- arch/arm/cpu/tegra20-common/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/cpu/tegra20-common/Makefile b/arch/arm/cpu/tegra20-common/Makefile index 32ddbda..0e4b3fc 100644 --- a/arch/arm/cpu/tegra20-common/Makefile +++ b/arch/arm/cpu/tegra20-common/Makefile @@ -9,7 +9,7 @@ # The AVP is ARMv4T architecture so we must use special compiler # flags for any startup files it might use. -CFLAGS_arch/arm/cpu/tegra20-common/warmboot_avp.o += -march=armv4t +CFLAGS_warmboot_avp.o += -march=armv4t obj-y += clock.o funcmux.o pinmux.o obj-$(CONFIG_TEGRA_LP0) += warmboot.o crypto.o warmboot_avp.o -- 1.8.3.2

2 1

[U-Boot] [PATCH] board: enable 32kHz RTC OSC at B&R boards
by Hannes Petermaier 31 Mar '14

31 Mar '14

Since RTC-Clock is needed on all B&R boards, the OSC will be enabled wihtin SPL-stage. Signed-off-by: Hannes Petermaier <oe5hpm(a)oevsv.at> --- include/configs/bur_am335x_common.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/configs/bur_am335x_common.h b/include/configs/bur_am335x_common.h index 7bbe596..7adc8c0 100644 --- a/include/configs/bur_am335x_common.h +++ b/include/configs/bur_am335x_common.h @@ -22,7 +22,7 @@ /* Timer information */ #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ #define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */ - +#define CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC /* enable 32kHz OSC at bootime */ #define CONFIG_SPL_POWER_SUPPORT #define CONFIG_POWER_TPS65217 -- 1.7.9.5

2 1

[U-Boot] All Sparc boards are broken
by Masahiro Yamada 31 Mar '14

31 Mar '14

Hi Daniel, All Sparc boards are broken because get_tbclk() func is missing. lib/built-in.o: In function `tick_to_time': u-boot/lib/time.c:56: undefined reference to `get_tbclk' lib/built-in.o: In function `usec_to_tick': u-boot/lib/time.c:80: undefined reference to `get_tbclk' Nothing has been done with that error since Rob Herring's common timer framework. Daniel, can you fix them? Best Regards Masahiro Yamada

2 1

[U-Boot] [PATCH] tools: fix Makefile to clean-up fit_info and fit_check_sign
by Masahiro Yamada 31 Mar '14

31 Mar '14

We should avoid the description in Makefile like this ifdef CONFIG_FIT_SIGNATURE hostprogs-y += fit_info$(SFX) fit_check_sign$(SFX) endif Otherwise, fit_info and fit_check_sign would never be cleaned by "make clean". Cc: Heiko Schocher <hs(a)denx.de> --- tools/Makefile | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/tools/Makefile b/tools/Makefile index c5c378c..c34df4f 100644 --- a/tools/Makefile +++ b/tools/Makefile @@ -60,9 +60,7 @@ hostprogs-y += mkenvimage$(SFX) mkenvimage$(SFX)-objs := crc32.o mkenvimage.o os_support.o hostprogs-y += dumpimage$(SFX) mkimage$(SFX) -ifdef CONFIG_FIT_SIGNATURE -hostprogs-y += fit_info$(SFX) fit_check_sign$(SFX) -endif +hostprogs-$(CONFIG_FIT_SIGNATURE) += fit_info$(SFX) fit_check_sign$(SFX) FIT_SIG_OBJS-$(CONFIG_FIT_SIGNATURE) := image-sig.o # Flattened device tree objects -- 1.8.3.2

2 3

[U-Boot] Pull request: u-boot-sh/master
by Nobuhiro Iwamatsu 31 Mar '14

31 Mar '14

Dear Tom Rini. Please pull u-boot-sh master branch. The following changes since commit 0b2da7e209f4110b7c81d578336a10330e4a4404: blackfin: mmc: Correct mmc_host_is_spi and bfin_sdh.c (2014-03-28 16:55:29 -0400) are available in the git repository at: git://git.denx.de/u-boot-sh master for you to fetch changes up to 82778e92c2816036ed79cdfb47e6eb6f6487a3f9: board: ecovec: fix USB0 clock enable (2014-03-31 10:48:02 +0900) ---------------------------------------------------------------- Baruch Siach (2): board: ecovec: fix debug LEDs pin direction board: ecovec: fix USB0 clock enable board/renesas/ecovec/ecovec.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) -- Nobuhiro Iwamatsu iwamatsu at {nigauri.org / debian.org} GPG ID: 40AD1FA6

3 3

[U-Boot] [i2c] Pull request
by Heiko Schocher 31 Mar '14

31 Mar '14

Hello Tom, please pull from u-boot-i2c.git, thanks! The following changes since commit 0b2da7e209f4110b7c81d578336a10330e4a4404: blackfin: mmc: Correct mmc_host_is_spi and bfin_sdh.c (2014-03-28 16:55:29 -0400) are available in the git repository at: git://git.denx.de/u-boot-i2c.git master for you to fetch changes up to 462d1883f78353c5ed9d09de45a9b5b2422793a3: drivers: i2c: delete an unused source file (2014-03-31 07:30:55 +0200) ---------------------------------------------------------------- Masahiro Yamada (1): drivers: i2c: delete an unused source file drivers/i2c/adi_i2c.c | 387 -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 1 file changed, 387 deletions(-) delete mode 100644 drivers/i2c/adi_i2c.c bye, Heiko -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

2 1