December 2014 - U-Boot

[U-Boot] [PATCH 0/19] powerpc: Introduce device tree control and driver model
by Simon Glass 26 Jan '15

26 Jan '15

This series does a small amount of tweaking to support device tree control (CONFIG_OF_CONTROL) on PowerPC platforms. It also adds support for driver model. In both cases the main effort is to set things up correctly before calling board_init_f(). A new generic function, board_init_f_mem() is introduced. This does the various memory calculations in C code, since they are messy in assembler and every architecture should in fact be the same. A later series will adjust ARM and x86 to use this function. As an example, the Canyonlands boards are converted over to use device tree control and driver model for their serial console. It should be fairly straightforward to convert over other boards. Simon Glass (18): Introduce board_init_f_mem() to handle early memory layout powerpc: Permit device tree control of U-Boot (CONFIG_OF_CONTROL) powerpc: ppc4xx: canyonlands: config: Tidy up CONFIGs and config.mk powerpc: ppc4xx: Move CANYONLANDS/GLACIER/ARCHES to Kconfig powerpc: ppc4xx: Add ramboot config for glacier powerpc: ppc4xx: canyonlands: Move to generic board powerpc: ppc4xx: dts: Bring in canyonlands device tree files powerpc: ppc4xx: Call board_init_f_mem() for generic board powerpc: ppc4xx: Add a gpio.h header file powerpc: ppc4xx: Allow the end of u-boot.bin to be found powerpc: ppc4xx: Use CONFIG_OF_CONTROL for canyonlands boards ppc: amcc: Omit unneeded ns16550 CONFIG if using driver model powerpc: Add serial driver for driver model dm: powerpc: ppc4xx: Move glacier to use driver model for serial powerpc: Add linkage.h file serial: Support an early UART for debugging serial: ns16550: Support debug UART powerpc: ppc4xx: Provide early debug UART defaults Stefan Roese (1): WIP: powerpc: ppc4xx: Somehow BSS is not cleared in RAMBOOT case arch/Kconfig | 1 + arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c | 8 + arch/powerpc/cpu/ppc4xx/config.mk | 5 +- arch/powerpc/cpu/ppc4xx/cpu_init.c | 2 + arch/powerpc/cpu/ppc4xx/start.S | 18 +- arch/powerpc/cpu/ppc4xx/u-boot.lds | 8 +- arch/powerpc/dts/Makefile | 11 + arch/powerpc/dts/arches.dts | 339 ++++++++++++++++ arch/powerpc/dts/canyonlands.dts | 555 ++++++++++++++++++++++++++ arch/powerpc/dts/glacier.dts | 579 ++++++++++++++++++++++++++++ arch/powerpc/include/asm/arch-ppc4xx/gpio.h | 7 + arch/powerpc/include/asm/linkage.h | 7 + arch/powerpc/include/asm/ppc460ex_gt.h | 2 + arch/powerpc/lib/board.c | 3 + board/amcc/canyonlands/Kconfig | 35 ++ board/amcc/canyonlands/MAINTAINERS | 1 + board/amcc/canyonlands/config.mk | 2 - board/amcc/canyonlands/u-boot-ram.lds | 85 ++++ common/board_f.c | 18 + common/board_r.c | 8 +- configs/arches_defconfig | 5 +- configs/canyonlands_defconfig | 5 +- configs/glacier_defconfig | 5 +- configs/glacier_ramboot_defconfig | 8 + drivers/serial/Kconfig | 59 +++ drivers/serial/Makefile | 1 + drivers/serial/ns16550.c | 42 +- drivers/serial/serial_ppc.c | 40 ++ include/configs/amcc-common.h | 2 + include/configs/canyonlands.h | 38 +- include/debug_uart.h | 139 +++++++ 31 files changed, 2006 insertions(+), 32 deletions(-) create mode 100644 arch/powerpc/dts/Makefile create mode 100644 arch/powerpc/dts/arches.dts create mode 100644 arch/powerpc/dts/canyonlands.dts create mode 100644 arch/powerpc/dts/glacier.dts create mode 100644 arch/powerpc/include/asm/arch-ppc4xx/gpio.h create mode 100644 arch/powerpc/include/asm/linkage.h create mode 100644 board/amcc/canyonlands/u-boot-ram.lds create mode 100644 configs/glacier_ramboot_defconfig create mode 100644 drivers/serial/serial_ppc.c create mode 100644 include/debug_uart.h -- 2.2.0.rc0.207.ga3a616c

4 32

[U-Boot] [PATCH v2 1/2] ARM: HYP/non-sec: Make variable gic_dist_addr as a local one
by Tang Yuantian 24 Jan '15

24 Jan '15

Defining variable gic_dist_addr as a globe one prevents some functions, which use it, from being used before relocation which is the case in the deep sleep resume process on Freescale SoC platforms. Besides, we can always get the GIC base address by calling get_gicd_base_address() without referring gic_dist_addr. Signed-off-by: Tang Yuantian <Yuantian.Tang(a)freescale.com> --- v2: - change variable gic_dist_addr back as local arch/arm/cpu/armv7/virt-v7.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/arch/arm/cpu/armv7/virt-v7.c b/arch/arm/cpu/armv7/virt-v7.c index 651ca40..b69fd37 100644 --- a/arch/arm/cpu/armv7/virt-v7.c +++ b/arch/arm/cpu/armv7/virt-v7.c @@ -15,8 +15,6 @@ #include <asm/io.h> #include <asm/secure.h> -unsigned long gic_dist_addr; - static unsigned int read_id_pfr1(void) { unsigned int reg; @@ -68,6 +66,12 @@ static void kick_secondary_cpus_gic(unsigned long gicdaddr) void __weak smp_kick_all_cpus(void) { + unsigned long gic_dist_addr; + + gic_dist_addr = get_gicd_base_address(); + if (gic_dist_addr == -1) + return; + kick_secondary_cpus_gic(gic_dist_addr); } @@ -75,6 +79,7 @@ int armv7_init_nonsec(void) { unsigned int reg; unsigned itlinesnr, i; + unsigned long gic_dist_addr; /* check whether the CPU supports the security extensions */ reg = read_id_pfr1(); -- 2.1.0.27.g96db324

3 5

[U-Boot] [PATCH] ls102xa: fdt: Disable QSPI and DSPI in NOR/NAND/SD boot
by Alison Wang 24 Jan '15

24 Jan '15

As QSPI/DSPI and IFC are pin multiplexed, QSPI and DSPI are only enabled in QSPI boot, and disabled in other boot modes. IFC is enabled in NOR/NAND/SD boot, and disabled in QSPI boot. This patch will add fdt support for the above rules. Signed-off-by: Alison Wang <alison.wang(a)freescale.com> --- arch/arm/cpu/armv7/ls102xa/fdt.c | 13 +++++++++++++ arch/arm/include/asm/arch-ls102xa/config.h | 4 ++++ 2 files changed, 17 insertions(+) diff --git a/arch/arm/cpu/armv7/ls102xa/fdt.c b/arch/arm/cpu/armv7/ls102xa/fdt.c index 989780d..b5c8d9d 100644 --- a/arch/arm/cpu/armv7/ls102xa/fdt.c +++ b/arch/arm/cpu/armv7/ls102xa/fdt.c @@ -133,4 +133,17 @@ void ft_cpu_setup(void *blob, bd_t *bd) do_fixup_by_compat_u32(blob, "fsl, ls1021a-flexcan", "clock-frequency", busclk / 2, 1); + +#ifdef CONFIG_QSPI_BOOT + off = fdt_node_offset_by_compat_reg(blob, FSL_IFC_COMPAT, + CONFIG_SYS_IFC_ADDR); + fdt_set_node_status(blob, off, FDT_STATUS_DISABLED, 0); +#else + off = fdt_node_offset_by_compat_reg(blob, FSL_QSPI_COMPAT, + QSPI0_BASE_ADDR); + fdt_set_node_status(blob, off, FDT_STATUS_DISABLED, 0); + off = fdt_node_offset_by_compat_reg(blob, FSL_DSPI_COMPAT, + DSPI1_BASE_ADDR); + fdt_set_node_status(blob, off, FDT_STATUS_DISABLED, 0); +#endif } diff --git a/arch/arm/include/asm/arch-ls102xa/config.h b/arch/arm/include/asm/arch-ls102xa/config.h index 5e934da..884c30e 100644 --- a/arch/arm/include/asm/arch-ls102xa/config.h +++ b/arch/arm/include/asm/arch-ls102xa/config.h @@ -101,4 +101,8 @@ #error SoC not defined #endif +#define FSL_IFC_COMPAT "fsl,ifc" +#define FSL_QSPI_COMPAT "fsl,ls1-qspi" +#define FSL_DSPI_COMPAT "fsl,vf610-dspi" + #endif /* _ASM_ARMV7_LS102XA_CONFIG_ */ -- 2.1.0.27.g96db324

2 1

[U-Boot] [PATCH] ls102xa: dcu: Add platform support for DCU on LS1021AQDS board
by Xiubo Li 24 Jan '15

24 Jan '15

This patch adds the CH7301 HDMI options and the common configuration for DCU on LS1021AQDS board. Signed-off-by: Xiubo Li <Li.Xiubo(a)freescale.com> Signed-off-by: Alison Wang <alison.wang(a)freescale.com> Cc: Jason Jin <Jason.Jin(a)freescale.com> --- board/freescale/ls1021aqds/Makefile | 1 + board/freescale/ls1021aqds/dcu.c | 92 +++++++++++++++++++++++++++ board/freescale/ls1021aqds/ls1021aqds.c | 4 ++ board/freescale/ls1021aqds/ls1021aqds_qixis.h | 2 + include/configs/ls1021aqds.h | 20 ++++++ 5 files changed, 119 insertions(+) create mode 100644 board/freescale/ls1021aqds/dcu.c diff --git a/board/freescale/ls1021aqds/Makefile b/board/freescale/ls1021aqds/Makefile index 3b6903c..ab02344 100644 --- a/board/freescale/ls1021aqds/Makefile +++ b/board/freescale/ls1021aqds/Makefile @@ -7,3 +7,4 @@ obj-y += ls1021aqds.o obj-y += ddr.o obj-y += eth.o +obj-$(CONFIG_FSL_DCU_FB) += dcu.o diff --git a/board/freescale/ls1021aqds/dcu.c b/board/freescale/ls1021aqds/dcu.c new file mode 100644 index 0000000..90f5bc0 --- /dev/null +++ b/board/freescale/ls1021aqds/dcu.c @@ -0,0 +1,92 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * FSL DCU Framebuffer driver + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <asm/io.h> +#include <common.h> +#include <fsl_dcu_fb.h> +#include <i2c.h> +#include "div64.h" +#include "../common/diu_ch7301.h" +#include "ls1021aqds_qixis.h" + +DECLARE_GLOBAL_DATA_PTR; + +static int select_i2c_ch_pca9547(u8 ch) +{ + int ret; + + ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); + if (ret) { + puts("PCA: failed to select proper channel\n"); + return ret; + } + + return 0; +} + +unsigned int dcu_set_pixel_clock(unsigned int pixclock) +{ + unsigned long long div; + + div = (unsigned long long)(gd->bus_clk / 1000); + div *= (unsigned long long)pixclock; + do_div(div, 1000000000); + + return div; +} + +int platform_dcu_init(unsigned int xres, unsigned int yres, + const char *port, + struct fb_videomode *dcu_fb_videomode) +{ + const char *name; + unsigned int pixel_format; + int ret; + u8 ch; + + /* Mux I2C3+I2C4 as HSYNC+VSYNC */ + ret = i2c_read(CONFIG_SYS_I2C_QIXIS_ADDR, QIXIS_DCU_BRDCFG5, + 1, &ch, 1); + if (ret) { + printf("Error: failed to read I2C @%02x\n", + CONFIG_SYS_I2C_QIXIS_ADDR); + return ret; + } + ch &= 0x1F; + ch |= 0xA0; + ret = i2c_write(CONFIG_SYS_I2C_QIXIS_ADDR, QIXIS_DCU_BRDCFG5, + 1, &ch, 1); + if (ret) { + printf("Error: failed to write I2C @%02x\n", + CONFIG_SYS_I2C_QIXIS_ADDR); + return ret; + } + + if (strncmp(port, "hdmi", 4) == 0) { + unsigned long pixval; + + name = "HDMI"; + + pixval = 1000000000 / dcu_fb_videomode->pixclock; + pixval *= 1000; + + i2c_set_bus_num(CONFIG_SYS_I2C_DVI_BUS_NUM); + select_i2c_ch_pca9547(I2C_MUX_CH_CH7301); + diu_set_dvi_encoder(pixval); + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + } else { + return 0; + } + + printf("DCU: Switching to %s monitor @ %ux%u\n", name, xres, yres); + + pixel_format = 32; + fsl_dcu_init(xres, yres, pixel_format); + + return 0; +} diff --git a/board/freescale/ls1021aqds/ls1021aqds.c b/board/freescale/ls1021aqds/ls1021aqds.c index 2bc029c..738b71e 100644 --- a/board/freescale/ls1021aqds/ls1021aqds.c +++ b/board/freescale/ls1021aqds/ls1021aqds.c @@ -194,6 +194,10 @@ int board_early_init_f(void) out_be32(&scfg->qspi_cfg, SCFG_QSPI_CLKSEL); #endif +#ifdef CONFIG_FSL_DCU_FB + out_be32(&scfg->pixclkcr, SCFG_PIXCLKCR_PXCKEN); +#endif + /* * Enable snoop requests and DVM message requests for * Slave insterface S4 (A7 core cluster) diff --git a/board/freescale/ls1021aqds/ls1021aqds_qixis.h b/board/freescale/ls1021aqds/ls1021aqds_qixis.h index 09b3be2..8e482eb 100644 --- a/board/freescale/ls1021aqds/ls1021aqds_qixis.h +++ b/board/freescale/ls1021aqds/ls1021aqds_qixis.h @@ -32,4 +32,6 @@ #define QIXIS_SRDS1CLK_100 0x0 +#define QIXIS_DCU_BRDCFG5 0x55 + #endif diff --git a/include/configs/ls1021aqds.h b/include/configs/ls1021aqds.h index 5e2c0c3..2ea1134 100644 --- a/include/configs/ls1021aqds.h +++ b/include/configs/ls1021aqds.h @@ -402,6 +402,7 @@ unsigned long get_board_ddr_clk(void); */ #define I2C_MUX_PCA_ADDR_PRI 0x77 #define I2C_MUX_CH_DEFAULT 0x8 +#define I2C_MUX_CH_CH7301 0xC /* * MMC @@ -468,6 +469,25 @@ unsigned long get_board_ddr_clk(void); #endif /* + * Video + */ +#define CONFIG_FSL_DCU_FB + +#ifdef CONFIG_FSL_DCU_FB +#define CONFIG_VIDEO +#define CONFIG_CMD_BMP +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_BMP_LOGO + +#define CONFIG_FSL_DIU_CH7301 +#define CONFIG_SYS_I2C_DVI_BUS_NUM 0 +#define CONFIG_SYS_I2C_QIXIS_ADDR 0x66 +#define CONFIG_SYS_I2C_DVI_ADDR 0x75 +#endif + +/* * eTSEC */ #define CONFIG_TSEC_ENET -- 2.1.0.27.g96db324

2 1

[U-Boot] [PATCH] crypto/fsl: Add fixup for crypto node
by Ruchika Gupta 24 Jan '15

24 Jan '15

Era property is added in the crypto node in device tree. Move the code to do so from arch/powerpc/mpc8xxx/fdt.c to drivers/sec/sec.c so that it can be used across arm and powerpc platforms having crypto node. Signed-off-by: Ruchika Gupta <ruchika.gupta(a)freescale.com> --- arch/arm/cpu/armv7/ls102xa/fdt.c | 17 ++++ arch/powerpc/cpu/mpc8xxx/fdt.c | 170 ----------------------------------- arch/powerpc/include/asm/config.h | 1 + drivers/crypto/fsl/Makefile | 1 + drivers/crypto/fsl/sec.c | 184 ++++++++++++++++++++++++++++++++++++++ 5 files changed, 203 insertions(+), 170 deletions(-) create mode 100644 drivers/crypto/fsl/sec.c diff --git a/arch/arm/cpu/armv7/ls102xa/fdt.c b/arch/arm/cpu/armv7/ls102xa/fdt.c index 989780d..0fda694 100644 --- a/arch/arm/cpu/armv7/ls102xa/fdt.c +++ b/arch/arm/cpu/armv7/ls102xa/fdt.c @@ -15,6 +15,8 @@ #include <fsl_esdhc.h> #endif #include <tsec.h> +#include <asm/arch/immap_ls102xa.h> +#include <fsl_sec.h> DECLARE_GLOBAL_DATA_PTR; @@ -77,9 +79,24 @@ void ft_cpu_setup(void *blob, bd_t *bd) int off; int val; const char *sysclk_path; + struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); + unsigned int svr; + svr = in_be32(&gur->svr); unsigned long busclk = get_bus_freq(0); + /* delete crypto node if not on an E-processor */ + if (!IS_E_PROCESSOR(svr)) + fdt_fixup_crypto_node(blob, 0); +#if CONFIG_SYS_FSL_SEC_COMPAT >= 4 + else { + ccsr_sec_t __iomem *sec; + + sec = (void __iomem *)CONFIG_SYS_FSL_SEC_ADDR; + fdt_fixup_crypto_node(blob, sec_in32(&sec->secvid_ms)); + } +#endif + fdt_fixup_ethernet(blob); off = fdt_node_offset_by_prop_value(blob, -1, "device_type", "cpu", 4); diff --git a/arch/powerpc/cpu/mpc8xxx/fdt.c b/arch/powerpc/cpu/mpc8xxx/fdt.c index 1c63f93..9cc1676 100644 --- a/arch/powerpc/cpu/mpc8xxx/fdt.c +++ b/arch/powerpc/cpu/mpc8xxx/fdt.c @@ -73,176 +73,6 @@ void ft_fixup_num_cores(void *blob) { } #endif /* defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) */ -/* - * update crypto node properties to a specified revision of the SEC - * called with sec_rev == 0 if not on an E processor - */ -#if CONFIG_SYS_FSL_SEC_COMPAT == 2 /* SEC 2.x/3.x */ -void fdt_fixup_crypto_node(void *blob, int sec_rev) -{ - static const struct sec_rev_prop { - u32 sec_rev; - u32 num_channels; - u32 channel_fifo_len; - u32 exec_units_mask; - u32 descriptor_types_mask; - } sec_rev_prop_list [] = { - { 0x0200, 4, 24, 0x07e, 0x01010ebf }, /* SEC 2.0 */ - { 0x0201, 4, 24, 0x0fe, 0x012b0ebf }, /* SEC 2.1 */ - { 0x0202, 1, 24, 0x04c, 0x0122003f }, /* SEC 2.2 */ - { 0x0204, 4, 24, 0x07e, 0x012b0ebf }, /* SEC 2.4 */ - { 0x0300, 4, 24, 0x9fe, 0x03ab0ebf }, /* SEC 3.0 */ - { 0x0301, 4, 24, 0xbfe, 0x03ab0ebf }, /* SEC 3.1 */ - { 0x0303, 4, 24, 0x97c, 0x03a30abf }, /* SEC 3.3 */ - }; - static char compat_strlist[ARRAY_SIZE(sec_rev_prop_list) * - sizeof("fsl,secX.Y")]; - int crypto_node, sec_idx, err; - char *p; - u32 val; - - /* locate crypto node based on lowest common compatible */ - crypto_node = fdt_node_offset_by_compatible(blob, -1, "fsl,sec2.0"); - if (crypto_node == -FDT_ERR_NOTFOUND) - return; - - /* delete it if not on an E-processor */ - if (crypto_node > 0 && !sec_rev) { - fdt_del_node(blob, crypto_node); - return; - } - - /* else we got called for possible uprev */ - for (sec_idx = 0; sec_idx < ARRAY_SIZE(sec_rev_prop_list); sec_idx++) - if (sec_rev_prop_list[sec_idx].sec_rev == sec_rev) - break; - - if (sec_idx == ARRAY_SIZE(sec_rev_prop_list)) { - puts("warning: unknown SEC revision number\n"); - return; - } - - val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].num_channels); - err = fdt_setprop(blob, crypto_node, "fsl,num-channels", &val, 4); - if (err < 0) - printf("WARNING: could not set crypto property: %s\n", - fdt_strerror(err)); - - val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].descriptor_types_mask); - err = fdt_setprop(blob, crypto_node, "fsl,descriptor-types-mask", &val, 4); - if (err < 0) - printf("WARNING: could not set crypto property: %s\n", - fdt_strerror(err)); - - val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].exec_units_mask); - err = fdt_setprop(blob, crypto_node, "fsl,exec-units-mask", &val, 4); - if (err < 0) - printf("WARNING: could not set crypto property: %s\n", - fdt_strerror(err)); - - val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].channel_fifo_len); - err = fdt_setprop(blob, crypto_node, "fsl,channel-fifo-len", &val, 4); - if (err < 0) - printf("WARNING: could not set crypto property: %s\n", - fdt_strerror(err)); - - val = 0; - while (sec_idx >= 0) { - p = compat_strlist + val; - val += sprintf(p, "fsl,sec%d.%d", - (sec_rev_prop_list[sec_idx].sec_rev & 0xff00) >> 8, - sec_rev_prop_list[sec_idx].sec_rev & 0x00ff) + 1; - sec_idx--; - } - err = fdt_setprop(blob, crypto_node, "compatible", &compat_strlist, val); - if (err < 0) - printf("WARNING: could not set crypto property: %s\n", - fdt_strerror(err)); -} -#elif CONFIG_SYS_FSL_SEC_COMPAT >= 4 /* SEC4 */ -static u8 caam_get_era(void) -{ - static const struct { - u16 ip_id; - u8 maj_rev; - u8 era; - } caam_eras[] = { - {0x0A10, 1, 1}, - {0x0A10, 2, 2}, - {0x0A12, 1, 3}, - {0x0A14, 1, 3}, - {0x0A14, 2, 4}, - {0x0A16, 1, 4}, - {0x0A10, 3, 4}, - {0x0A11, 1, 4}, - {0x0A18, 1, 4}, - {0x0A11, 2, 5}, - {0x0A12, 2, 5}, - {0x0A13, 1, 5}, - {0x0A1C, 1, 5} - }; - - ccsr_sec_t __iomem *sec = (void __iomem *)CONFIG_SYS_FSL_SEC_ADDR; - u32 secvid_ms = sec_in32(&sec->secvid_ms); - u32 ccbvid = sec_in32(&sec->ccbvid); - u16 ip_id = (secvid_ms & SEC_SECVID_MS_IPID_MASK) >> - SEC_SECVID_MS_IPID_SHIFT; - u8 maj_rev = (secvid_ms & SEC_SECVID_MS_MAJ_REV_MASK) >> - SEC_SECVID_MS_MAJ_REV_SHIFT; - u8 era = (ccbvid & SEC_CCBVID_ERA_MASK) >> SEC_CCBVID_ERA_SHIFT; - - int i; - - if (era) /* This is '0' prior to CAAM ERA-6 */ - return era; - - for (i = 0; i < ARRAY_SIZE(caam_eras); i++) - if (caam_eras[i].ip_id == ip_id && - caam_eras[i].maj_rev == maj_rev) - return caam_eras[i].era; - - return 0; -} - -static void fdt_fixup_crypto_era(void *blob, u32 era) -{ - int err; - int crypto_node; - - crypto_node = fdt_path_offset(blob, "crypto"); - if (crypto_node < 0) { - printf("WARNING: Missing crypto node\n"); - return; - } - - err = fdt_setprop(blob, crypto_node, "fsl,sec-era", &era, - sizeof(era)); - if (err < 0) { - printf("ERROR: could not set fsl,sec-era property: %s\n", - fdt_strerror(err)); - } -} - -void fdt_fixup_crypto_node(void *blob, int sec_rev) -{ - u8 era; - - if (!sec_rev) { - fdt_del_node_and_alias(blob, "crypto"); - return; - } - - /* Add SEC ERA information in compatible */ - era = caam_get_era(); - if (era) { - fdt_fixup_crypto_era(blob, era); - } else { - printf("WARNING: Unable to get ERA for CAAM rev: %d\n", - sec_rev); - } -} -#endif - int fdt_fixup_phy_connection(void *blob, int offset, phy_interface_t phyc) { return fdt_setprop_string(blob, offset, "phy-connection-type", diff --git a/arch/powerpc/include/asm/config.h b/arch/powerpc/include/asm/config.h index 423a6fb..65496d0 100644 --- a/arch/powerpc/include/asm/config.h +++ b/arch/powerpc/include/asm/config.h @@ -75,6 +75,7 @@ * SEC (crypto unit) major compatible version determination */ #if defined(CONFIG_MPC83xx) +#define CONFIG_SYS_FSL_SEC_BE #define CONFIG_SYS_FSL_SEC_COMPAT 2 #endif diff --git a/drivers/crypto/fsl/Makefile b/drivers/crypto/fsl/Makefile index cb13d2e..067d0a9 100644 --- a/drivers/crypto/fsl/Makefile +++ b/drivers/crypto/fsl/Makefile @@ -6,5 +6,6 @@ # Version 2 as published by the Free Software Foundation. # +obj-y += sec.o obj-$(CONFIG_FSL_CAAM) += jr.o fsl_hash.o jobdesc.o error.o obj-$(CONFIG_CMD_BLOB) += fsl_blob.o diff --git a/drivers/crypto/fsl/sec.c b/drivers/crypto/fsl/sec.c new file mode 100644 index 0000000..443ee96 --- /dev/null +++ b/drivers/crypto/fsl/sec.c @@ -0,0 +1,184 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <libfdt.h> +#include <fdt_support.h> +#if CONFIG_SYS_FSL_SEC_COMPAT == 2 || CONFIG_SYS_FSL_SEC_COMPAT >= 4 +#include <fsl_sec.h> +#endif + +/* + * update crypto node properties to a specified revision of the SEC + * called with sec_rev == 0 if not on an E processor + */ +#if CONFIG_SYS_FSL_SEC_COMPAT == 2 /* SEC 2.x/3.x */ +void fdt_fixup_crypto_node(void *blob, int sec_rev) +{ + static const struct sec_rev_prop { + u32 sec_rev; + u32 num_channels; + u32 channel_fifo_len; + u32 exec_units_mask; + u32 descriptor_types_mask; + } sec_rev_prop_list[] = { + { 0x0200, 4, 24, 0x07e, 0x01010ebf }, /* SEC 2.0 */ + { 0x0201, 4, 24, 0x0fe, 0x012b0ebf }, /* SEC 2.1 */ + { 0x0202, 1, 24, 0x04c, 0x0122003f }, /* SEC 2.2 */ + { 0x0204, 4, 24, 0x07e, 0x012b0ebf }, /* SEC 2.4 */ + { 0x0300, 4, 24, 0x9fe, 0x03ab0ebf }, /* SEC 3.0 */ + { 0x0301, 4, 24, 0xbfe, 0x03ab0ebf }, /* SEC 3.1 */ + { 0x0303, 4, 24, 0x97c, 0x03a30abf }, /* SEC 3.3 */ + }; + static char compat_strlist[ARRAY_SIZE(sec_rev_prop_list) * + sizeof("fsl,secX.Y")]; + int crypto_node, sec_idx, err; + char *p; + u32 val; + + /* locate crypto node based on lowest common compatible */ + crypto_node = fdt_node_offset_by_compatible(blob, -1, "fsl,sec2.0"); + if (crypto_node == -FDT_ERR_NOTFOUND) + return; + + /* delete it if not on an E-processor */ + if (crypto_node > 0 && !sec_rev) { + fdt_del_node(blob, crypto_node); + return; + } + + /* else we got called for possible uprev */ + for (sec_idx = 0; sec_idx < ARRAY_SIZE(sec_rev_prop_list); sec_idx++) + if (sec_rev_prop_list[sec_idx].sec_rev == sec_rev) + break; + + if (sec_idx == ARRAY_SIZE(sec_rev_prop_list)) { + puts("warning: unknown SEC revision number\n"); + return; + } + + val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].num_channels); + err = fdt_setprop(blob, crypto_node, "fsl,num-channels", &val, 4); + if (err < 0) + printf("WARNING: could not set crypto property: %s\n", + fdt_strerror(err)); + + val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].descriptor_types_mask); + err = fdt_setprop(blob, crypto_node, "fsl,descriptor-types-mask", + &val, 4); + if (err < 0) + printf("WARNING: could not set crypto property: %s\n", + fdt_strerror(err)); + + val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].exec_units_mask); + err = fdt_setprop(blob, crypto_node, "fsl,exec-units-mask", &val, 4); + if (err < 0) + printf("WARNING: could not set crypto property: %s\n", + fdt_strerror(err)); + + val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].channel_fifo_len); + err = fdt_setprop(blob, crypto_node, "fsl,channel-fifo-len", &val, 4); + if (err < 0) + printf("WARNING: could not set crypto property: %s\n", + fdt_strerror(err)); + + val = 0; + while (sec_idx >= 0) { + p = compat_strlist + val; + val += sprintf(p, "fsl,sec%d.%d", + (sec_rev_prop_list[sec_idx].sec_rev & 0xff00) >> 8, + sec_rev_prop_list[sec_idx].sec_rev & 0x00ff) + 1; + sec_idx--; + } + err = fdt_setprop(blob, crypto_node, "compatible", &compat_strlist, + val); + if (err < 0) + printf("WARNING: could not set crypto property: %s\n", + fdt_strerror(err)); +} +#elif CONFIG_SYS_FSL_SEC_COMPAT >= 4 /* SEC4 */ +static u8 caam_get_era(void) +{ + static const struct { + u16 ip_id; + u8 maj_rev; + u8 era; + } caam_eras[] = { + {0x0A10, 1, 1}, + {0x0A10, 2, 2}, + {0x0A12, 1, 3}, + {0x0A14, 1, 3}, + {0x0A14, 2, 4}, + {0x0A16, 1, 4}, + {0x0A10, 3, 4}, + {0x0A11, 1, 4}, + {0x0A18, 1, 4}, + {0x0A11, 2, 5}, + {0x0A12, 2, 5}, + {0x0A13, 1, 5}, + {0x0A1C, 1, 5} + }; + + ccsr_sec_t __iomem *sec = (void __iomem *)CONFIG_SYS_FSL_SEC_ADDR; + u32 secvid_ms = sec_in32(&sec->secvid_ms); + u32 ccbvid = sec_in32(&sec->ccbvid); + u16 ip_id = (secvid_ms & SEC_SECVID_MS_IPID_MASK) >> + SEC_SECVID_MS_IPID_SHIFT; + u8 maj_rev = (secvid_ms & SEC_SECVID_MS_MAJ_REV_MASK) >> + SEC_SECVID_MS_MAJ_REV_SHIFT; + u8 era = (ccbvid & SEC_CCBVID_ERA_MASK) >> SEC_CCBVID_ERA_SHIFT; + + int i; + + if (era) /* This is '0' prior to CAAM ERA-6 */ + return era; + + for (i = 0; i < ARRAY_SIZE(caam_eras); i++) + if (caam_eras[i].ip_id == ip_id && + caam_eras[i].maj_rev == maj_rev) + return caam_eras[i].era; + + return 0; +} + +static void fdt_fixup_crypto_era(void *blob, u32 era) +{ + int err; + int crypto_node; + + crypto_node = fdt_path_offset(blob, "crypto"); + if (crypto_node < 0) { + printf("WARNING: Missing crypto node\n"); + return; + } + + err = fdt_setprop(blob, crypto_node, "fsl,sec-era", &era, + sizeof(era)); + if (err < 0) { + printf("ERROR: could not set fsl,sec-era property: %s\n", + fdt_strerror(err)); + } +} + +void fdt_fixup_crypto_node(void *blob, int sec_rev) +{ + u8 era; + + if (!sec_rev) { + fdt_del_node_and_alias(blob, "crypto"); + return; + } + + /* Add SEC ERA information in compatible */ + era = caam_get_era(); + if (era) { + fdt_fixup_crypto_era(blob, era); + } else { + printf("WARNING: Unable to get ERA for CAAM rev: %d\n", + sec_rev); + } +} +#endif -- 1.8.1.4

2 1

[U-Boot] [PATCH 1/2] arm: ls102xa: Add dummy gpio.h to enable CONFIG_OF_CONTROL
by Ruchika Gupta 24 Jan '15

24 Jan '15

If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled. It includes <asm/gpio.h> and then <asm/gpio.h> includes <asm/arch/gpio.h>. As a result, all the SoCs that enable CONFIG_OF_CONTROL must have <asm/arch/gpio.h> even if they do not support GPIO. The right fix would be to split the lib/fdtdec.c to remove dependency on GPIO.This commit adds a dummy <asm/arch/gpio.h> to support OF_CONTROL for LS102x platform. This dummy header will be removed after FDT-GPIO stuff is fixed correctly. Signed-off-by: Ruchika Gupta <ruchika.gupta(a)freescale.com> --- arch/arm/include/asm/arch-ls102xa/gpio.h | 15 +++++++++++++++ 1 file changed, 15 insertions(+) create mode 100644 arch/arm/include/asm/arch-ls102xa/gpio.h diff --git a/arch/arm/include/asm/arch-ls102xa/gpio.h b/arch/arm/include/asm/arch-ls102xa/gpio.h new file mode 100644 index 0000000..b704436 --- /dev/null +++ b/arch/arm/include/asm/arch-ls102xa/gpio.h @@ -0,0 +1,15 @@ +/* + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * Dummy header file to enable CONFIG_OF_CONTROL. + * If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled. + * It includes <asm/arch/gpio.h> via <asm/gpio.h>, so those SoCs that enable + * OF_CONTROL must have arch/gpio.h. + */ + +#ifndef __ASM_ARCH_LS102XA_GPIO_H_ +#define __ASM_ARCH_LS102XA_GPIO_H_ + +#endif -- 1.8.1.4

4 3

[U-Boot] [PATCH v1] ls102xa: etsec: Select ge0_clk125 for eTSEC clock muxing as default
by Alison Wang 24 Jan '15

24 Jan '15

This patch reverts to use ge0_clk125 for eTSEC clock muxing. For SAI and CAN which are pin multiplexed with RGMII1 in EC1 of RCW, ge2_clk125 will be used via hwconfig. Signed-off-by: Bhupesh Sharma <bhupesh.sharma(a)freescale.com> Signed-off-by: Alison Wang <alison.wang(a)freescale.com> --- arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h | 2 ++ board/freescale/ls1021aqds/ls1021aqds.c | 35 ++++++++++++++++++++++- 2 files changed, 36 insertions(+), 1 deletion(-) diff --git a/arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h b/arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h index 697d4ca..afdccdc 100644 --- a/arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h +++ b/arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h @@ -105,6 +105,8 @@ struct ccsr_gur { #define SCFG_ETSECDMAMCR_LE_BD_FR 0xf8001a0f #define SCFG_ETSECCMCR_GE2_CLK125 0x04000000 +#define SCFG_ETSECCMCR_GE0_CLK125 0x00000000 +#define SCFG_ETSECCMCR_GE1_CLK125 0x08000000 #define SCFG_PIXCLKCR_PXCKEN 0x80000000 #define SCFG_QSPI_CLKSEL 0xc0100000 diff --git a/board/freescale/ls1021aqds/ls1021aqds.c b/board/freescale/ls1021aqds/ls1021aqds.c index f08e54f..f4a5dda 100644 --- a/board/freescale/ls1021aqds/ls1021aqds.c +++ b/board/freescale/ls1021aqds/ls1021aqds.c @@ -48,6 +48,12 @@ enum { MUX_TYPE_SD_PC_SG_SG, }; +enum { + GE0_CLK125, + GE2_CLK125, + GE1_CLK125, +}; + int checkboard(void) { #ifndef CONFIG_QSPI_BOOT @@ -177,7 +183,6 @@ int board_early_init_f(void) #ifdef CONFIG_TSEC_ENET out_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR); - out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125); #endif #ifdef CONFIG_FSL_IFC @@ -244,6 +249,32 @@ void board_init_f(ulong dummy) } #endif +void config_etseccm_source(int etsec_gtx_125_mux) +{ + struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR; + + switch (etsec_gtx_125_mux) { + case GE0_CLK125: + out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE0_CLK125); + debug("etseccm set to GE0_CLK125\n"); + break; + + case GE2_CLK125: + out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125); + debug("etseccm set to GE2_CLK125\n"); + break; + + case GE1_CLK125: + out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE1_CLK125); + debug("etseccm set to GE1_CLK125\n"); + break; + + default: + printf("Error! trying to set etseccm to invalid value\n"); + break; + } +} + int config_board_mux(int ctrl_type) { u8 reg12, reg14; @@ -253,6 +284,7 @@ int config_board_mux(int ctrl_type) switch (ctrl_type) { case MUX_TYPE_CAN: + config_etseccm_source(GE2_CLK125); reg14 = SET_EC_MUX_SEL(reg14, PIN_MUX_SEL_CAN); break; case MUX_TYPE_IIC2: @@ -262,6 +294,7 @@ int config_board_mux(int ctrl_type) reg14 = SET_EC_MUX_SEL(reg14, PIN_MUX_SEL_RGMII); break; case MUX_TYPE_SAI: + config_etseccm_source(GE2_CLK125); reg14 = SET_EC_MUX_SEL(reg14, PIN_MUX_SEL_SAI); break; case MUX_TYPE_SDHC: -- 2.1.0.27.g96db324

2 1

[U-Boot] [PATCH V2] add README.distro file
by Stephen Warren 23 Jan '15

23 Jan '15

From: Dennis Gilmore <dennis(a)ausil.us> Add documentation on how to setup a system to use the generic distro configs and boot commands. This spells out what is needed to make a system conformant, but does not limit the board to only the defaults. Signed-off-by: Dennis Gilmore <dennis(a)ausil.us> [swarren, added concept, user config, BOOT_TARGET_DEVICES sections. edited the rest] Signed-off-by: Stephen Warren <swarren(a)nvidia.com> --- Back at the end of September, Otavio requested I or Dennis get this finished and submitted. Better late than never, right:-) doc/README.distro | 327 ++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 327 insertions(+) create mode 100644 doc/README.distro diff --git a/doc/README.distro b/doc/README.distro new file mode 100644 index 000000000000..da21aef4973a --- /dev/null +++ b/doc/README.distro @@ -0,0 +1,327 @@ +/* + * (C) Copyright 2014 Red Hat Inc. + * Copyright (c) 2014, NVIDIA CORPORATION. All rights reserved. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +Generic Distro Configuration Concept +==================================== + +Linux distributions are faced with supporting a variety of boot mechanisms, +environments or bootloaders (PC BIOS, EFI, U-Boot, Barebox, ...). This makes +life complicated. Worse, bootloaders such as U-Boot have a configurable set +of features, and each board chooses to enable a different set of features. +Hence, distros typically need to have board-specific knowledge in order to +set up a bootable system. + +This document defines a common set of U-Boot features that are required for +a distro to support the board in a generic fashion. Any board wishing to +allow distros to install and boot in an out-of-the-box fashion should enable +all these features. Linux distros can then create a single set of boot +support/install logic that targets these features. This will allow distros +to install on many boards without the need for board-specific logic. + +In fact, some of these features can be implemented by any bootloader, thus +decoupling distro install/boot logic from any knowledge of the bootloader. + +This model assumes that boards will load boot configuration files from a +regular storage mechanism (eMMC, SD card, USB Disk, SATA disk, etc.) with +a standard partitioning scheme (MBR, GPT). Boards that cannnot support this +storage model are outside the scope of this document, and may still need +board-specific installer/boot-configuration support in a distro. + +To some extent, this model assumes that a board has a separate boot flash +that contains U-Boot, and that the user has somehow installed U-Boot to this +flash before running the distro installer. Even on boards that do not conform +to this aspect of the model, the extent of the board-specific support in the +distro installer logic would be to install a board-specific U-Boot package to +the boot partition partition during installation. This distro-supplied U-Boot +can still implement the same features as on any other board, and hence the +distro's boot configuration file generation logic can still be board-agnostic. + +Locating Bootable Disks +----------------------- + +Typical desktop/server PCs search all (or a user-defined subset of) attached +storage devices for a bootable partition, then load the bootloader or boot +configuration files from there. A U-Boot board port that enables the features +mentioned in this document will search for boot configuration files in the +same way. + +Thus, distros do not need to manipulate any kind of bootloader-specific +configuration data to indicate which storage device the system should boot +from. + +Distros simply need to install the boot configuration files (see next +section) in an ext2/3/4 or FAT partition, mark the partition bootable (via +the MBR bootable flag, or GPT legacy_bios_bootable attribute), and U-Boot (or +any other bootloader) will find those boot files and execute them. This is +conceptually identical to creating a grub2 configuration file on a desktop +PC. + +Note that in the absense of any partition that is explicitly marked bootable, +U-Boot falls back to searching the first valid partition of a disk for boot +configuration files. Other bootloaders are recommended to do the same, since +I believe that partition table bootable flags aren't so commonly used outside +the realm of x86 PCs. + +U-Boot can also search for boot configuration files from a TFTP server. + +Boot Configuration Files +------------------------ + +The standard format for boot configuration files is that of extlinux.conf, as +handled by U-Boot's "syslinux" (disk) or "pxe boot" (network). This is roughly +as specified at: + +http://www.freedesktop.org/wiki/Specifications/BootLoaderSpec/ + +... with the exceptions that: + +* That document prescribes a separate configuration per boot menu option, + whereas U-Boot lumps all options into a single extlinux.conf file. Hence, + U-Boot searches for /extlinux/extlinux.conf then + /boot/extlinux/extlinux.conf on disk, or pxelinux.cfg/default over the + network. + +* Does not document the fdtdir option, which automatically selects the DTB to + pass to the kernel. + +One example extlinux.conf generated by the Fedora installer is: + +------------------------------------------------------------ +# extlinux.conf generated by anaconda + +ui menu.c32 + +menu autoboot Welcome to Fedora. Automatic boot in # second{,s}. Press a key for options. +menu title Fedora Boot Options. +menu hidden + +timeout 50 +#totaltimeout 9000 + +default Fedora (3.17.0-0.rc4.git2.1.fc22.armv7hl+lpae) 22 (Rawhide) + +label Fedora (3.17.0-0.rc4.git2.1.fc22.armv7hl) 22 (Rawhide) + kernel /boot/vmlinuz-3.17.0-0.rc4.git2.1.fc22.armv7hl + append ro root=UUID=8eac677f-8ea8-4270-8479-d5ddbb797450 console=ttyS0,115200n8 LANG=en_US.UTF-8 drm.debug=0xf + fdtdir /boot/dtb-3.17.0-0.rc4.git2.1.fc22.armv7hl + initrd /boot/initramfs-3.17.0-0.rc4.git2.1.fc22.armv7hl.img + +label Fedora (3.17.0-0.rc4.git2.1.fc22.armv7hl+lpae) 22 (Rawhide) + kernel /boot/vmlinuz-3.17.0-0.rc4.git2.1.fc22.armv7hl+lpae + append ro root=UUID=8eac677f-8ea8-4270-8479-d5ddbb797450 console=ttyS0,115200n8 LANG=en_US.UTF-8 drm.debug=0xf + fdtdir /boot/dtb-3.17.0-0.rc4.git2.1.fc22.armv7hl+lpae + initrd /boot/initramfs-3.17.0-0.rc4.git2.1.fc22.armv7hl+lpae.img + +label Fedora-0-rescue-8f6ba7b039524e0eb957d2c9203f04bc (0-rescue-8f6ba7b039524e0eb957d2c9203f04bc) + kernel /boot/vmlinuz-0-rescue-8f6ba7b039524e0eb957d2c9203f04bc + initrd /boot/initramfs-0-rescue-8f6ba7b039524e0eb957d2c9203f04bc.img + append ro root=UUID=8eac677f-8ea8-4270-8479-d5ddbb797450 console=ttyS0,115200n8 + fdtdir /boot/dtb-3.16.0-0.rc6.git1.1.fc22.armv7hl+lpae +------------------------------------------------------------ + +Another hand-crafted network boot configuration file is: + +------------------------------------------------------------ +TIMEOUT 100 + +MENU TITLE TFTP boot options + +LABEL jetson-tk1-emmc + MENU LABEL ../zImage root on Jetson TK1 eMMC + LINUX ../zImage + FDTDIR ../ + APPEND console=ttyS0,115200n8 console=tty1 loglevel=8 rootwait rw earlyprintk root=PARTUUID=80a5a8e9-c744-491a-93c1-4f4194fd690b + +LABEL venice2-emmc + MENU LABEL ../zImage root on Venice2 eMMC + LINUX ../zImage + FDTDIR ../ + APPEND console=ttyS0,115200n8 console=tty1 loglevel=8 rootwait rw earlyprintk root=PARTUUID=5f71e06f-be08-48ed-b1ef-ee4800cc860f + +LABEL sdcard + MENU LABEL ../zImage, root on 2GB sdcard + LINUX ../zImage + FDTDIR ../ + APPEND console=ttyS0,115200n8 console=tty1 loglevel=8 rootwait rw earlyprintk root=PARTUUID=b2f82cda-2535-4779-b467-094a210fbae7 + +LABEL fedora-installer-fk + MENU LABEL Fedora installer w/ Fedora kernel + LINUX fedora-installer/vmlinuz + INITRD fedora-installer/initrd.img.orig + FDTDIR fedora-installer/dtb + APPEND loglevel=8 ip=dhcp inst.repo=http://10.0.0.2/mirrors/fedora/linux/development/rawhide/armhfp/os/ rd.shell cma=64M +------------------------------------------------------------ + +U-Boot Implementation +===================== + +Enabling the distro options +--------------------------- + +In your board configuration file, include the following: + +------------------------------------------------------------ +#ifndef CONFIG_SPL_BUILD +#include <config_distro_defaults.h> +#include <config_distro_bootcmd.h> +#endif +------------------------------------------------------------ + +The first of those headers primarily enables a core set of U-Boot features, +such as support for MBR and GPT partitions, ext* and FAT filesystems, booting +raw zImage and initrd (rather than FIT- or uImage-wrapped files), etc. Network +boot support is also enabled here, which is useful in order to boot distro +installers given that distros do not commonly distribute bootable install +media for non-PC targets at present. + +Finally, a few options that are mostly relevant only when using U-Boot- +specific boot.scr boot configuration files are enabled This enables +compatibility with various board configurations that existed before these +distro default existed, and assumed boot.scr-based booting. + +The second of those headers sets up the default environment so that $bootcmd +is defined in a way that searches attached disks for boot configuration files, +and executes them if found. + +Required Environment Variables +------------------------------ + +The U-Boot "syslinux" and "pxe boot" commands require a number of environment +variables be set. Default values for these variables are often hard-coded into +CONFIG_EXTRA_ENV_SETTINGS in the board's U-Boot configuration file, so that +the user doesn't have to configure them. + +fdt_addr: + + Optional. If specified a dtb to boot the system must be available at the + given address. + +fdt_addr_r: + + Mandatory. The location in RAM where the dtb will be loaded or copied to + when processing the fdtdir/devicetreedir or fdt/devicetree options in + extlinux.conf. + + A size of 1MB for the FDT/DTB seems reasonable. + +ramdisk_addr_r: + + Mandatory. The location in RAM where the initial ramdisk will be loaded to + when processing the initrd option in extlinux.conf. + + It is recommended that this location be highest in RAM out of fdt_addr_, + kernel_addr_r, and ramdisk_addr_r, so that the RAM disk can vary in size + and use any available RAM. + +kernel_addr_r: + + Mandatory. The location in RAM where the kernel will be loaded to when + processing the kernel option in the extlinux.conf. + + The kernel should be located within the first 128M of RAM in order for the + kernel CONFIG_AUTO_ZRELADDR option to work, which is likely enabled on any + distro kernel. Since the kernel will decompress itself to 0x8000 after the + start of RAM, kernel_addr_rshould not overlap that area, or the kernel will + have to copy itself somewhere else first before decompression. + + A size of 16MB for the kernel is likely adequate. + +pxe_addr_r: + + Mandatory. The location in RAM where extlinux.conf will be loaded to prior + to processing. + + A size of 1MB for extlinux.conf is more than adequate. + +scriptaddr: + + Mandatory, if the boot script is boot.scr rather than extlinux.conf. The + location in RAM where boot.scr will be loaded to prior to execution. + + A size of 1MB for extlinux.conf is more than adequate. + +For suggestions on memory locations for ARM systems, you must follow the +guidelines specified in Documentation/arm/Booting in the Linux kernel tree. + +For a commented example of setting these values, please see the definition of +MEM_LAYOUT_ENV_SETTINGS in include/configs/tegra124-common.h. + +Boot Target Configuration +------------------------- + +<config_distro_bootcmd.h> defines $bootcmd and many helper command variables +that automatically search attached disks for boot configuration files and +execute them. Boards must provide configure <config_distro_bootcmd.h> so that +it supports the correct set of possible boot device types. To provide this +configuration, simply define macro BOOT_TARGET_DEVICES prior to including +<config_distro_bootcmd.h>. For example: + +------------------------------------------------------------ +#ifndef CONFIG_SPL_BUILD +#define BOOT_TARGET_DEVICES(func) \ + func(MMC, mmc, 1) \ + func(MMC, mmc, 0) \ + func(USB, usb, 0) \ + func(PXE, pxe, na) \ + func(DHCP, dhcp, na) +#include <config_distro_bootcmd.h> +#endif +------------------------------------------------------------ + +Each entry in the macro defines a single boot device (e.g. a specific eMMC +device or SD card) or type of boot device (e.g. USB disk). The parameters to +the func macro (passed in by the internal implementation of the header) are: + +- Upper-case disk type (MMC, SATA, SCSI, IDE, USB, DHCP, PXE). +- Lower-case disk type (same options as above). +- ID of the specific disk (MMC only) or ignored for other types. + +User Configuration +================== + +Once the user has installed U-Boot, it is expected that the environment will +be reset to the default values in order to enable $bootcmd and friends, as set +up by <config_distro_bootcmd.h>. After this, various environment variables may +be altered to influence the boot process: + +boot_targets: + + The list of boot locations searched. + + Example: mmc0, mmc1, usb, pxe + + Entries may be removed or re-ordered in this list to affect the boot order. + +boot_prefixes: + + For disk-based booting, the list of directories within a partition that are + searched for boot configuration files (extlinux.conf, boot.scr). + + Example: / /boot/ + + Entries may be removed or re-ordered in this list to affect the set of + directories which are searched. + +boot_scripts: + + The name of U-Boot style boot.scr files that $bootcmd searches for. + + Example: boot.scr.uimg boot.scr + + (Typically we expect extlinux.conf to be used, but execution of boot.scr is + maintained for backwards-compatibility.) + + Entries may be removed or re-ordered in this list to affect the set of + filenames which are supported. + +scan_dev_for_extlinux: + + If you want to disable extlinux.conf on any disk, delete this. + +scan_dev_for_scripts: + + If you want to disable boot.scr on any disk, delete this. -- 1.9.1

6 15

[U-Boot] [PATCH v4 00/18] Support for eMMC partitioning and related fixes
by Diego Santa Cruz 23 Jan '15

23 Jan '15

I have the need to hardware partition eMMC devices from U-Boot along with setting enhanced and reliable write attributes. This series of patches adds this support to U-Boot via a new mmc API, a few new members of struct mmc and a new mmc sub-command. It also features several fixes to the eMMC hardware partition support. I have tested this with Micron eMMC 4.41 parts and it is working as expected. This version resyncs to u-boot.git master d8bec60c1b0de7770f9b56ad092ab9be801d99af as some recent mmc changes conflicted with these patches, in particular the DDR mode support. Diego Santa Cruz (18): mmc: show hardware partition sizes in mmcinfo output mmc: extend mmcinfo to show enhanced partition attribute mmc: make eMMC general purpose partition numbering match spec mmc: skip mmcinfo partition info processing for eMMC < 4.41 mmc: incomplete test to switch to high-capacity group size definitions mmc: computation of eMMC GP partition size was missing 512 KiB factor mmc: read the size of eMMC enhanced user data area mmc: display size and start of eMMC enhanced user data area in mmcinfo mmc: fix erase_grp_size computation with high-capacity size definition mmc: read the high capacity WP group size for eMMC mmc: show the erase group size and HC WP group size in mmcinfo output mmc: eMMC partitioning data is not effective till partitioning completed mmc: the ext_csd data may be used during init even if reading failed mmc: add API to do eMMC hardware partitioning mmc: add mmc hwpartition sub-command to do eMMC hardware partitioning mmc: extend the mmc hardware partitioning API with write reliability mmc: extend the mmc hwpartition sub-command to change write reliability mmc: extend mmcinfo output to show partition write reliability settings common/cmd_mmc.c | 207 ++++++++++++++++++++++++++++++++++++++- drivers/mmc/mmc.c | 288 +++++++++++++++++++++++++++++++++++++++++++++++++----- include/mmc.h | 45 ++++++++- 3 files changed, 515 insertions(+), 25 deletions(-) -- 2.2.1

3 27

[U-Boot] [PATCH] phylib: add support for aquantia PHYs
by shh.xie＠gmail.com 23 Jan '15

23 Jan '15

From: Shaohui Xie <Shaohui.Xie(a)freescale.com> This patch supports AQ1202, AQ2104, AQR105 PHY. Signed-off-by: Shaohui Xie <Shaohui.Xie(a)freescale.com> --- drivers/net/phy/Makefile | 1 + drivers/net/phy/aquantia.c | 156 +++++++++++++++++++++++++++++++++++++++++++++ drivers/net/phy/phy.c | 3 + include/phy.h | 1 + 4 files changed, 161 insertions(+) create mode 100644 drivers/net/phy/aquantia.c diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile index 9556536..87d5c9c 100644 --- a/drivers/net/phy/Makefile +++ b/drivers/net/phy/Makefile @@ -11,6 +11,7 @@ obj-$(CONFIG_MV88E6352_SWITCH) += mv88e6352.o obj-$(CONFIG_PHYLIB) += phy.o obj-$(CONFIG_PHYLIB_10G) += generic_10g.o +obj-$(CONFIG_PHY_AQUANTIA) += aquantia.o obj-$(CONFIG_PHY_ATHEROS) += atheros.o obj-$(CONFIG_PHY_BROADCOM) += broadcom.o obj-$(CONFIG_PHY_DAVICOM) += davicom.o diff --git a/drivers/net/phy/aquantia.c b/drivers/net/phy/aquantia.c new file mode 100644 index 0000000..ef4da4e --- /dev/null +++ b/drivers/net/phy/aquantia.c @@ -0,0 +1,156 @@ +/* + * Aquantia PHY drivers + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Copyright 2014 Freescale Semiconductor, Inc. + */ +#include <config.h> +#include <common.h> +#include <phy.h> + +#ifndef CONFIG_PHYLIB_10G +#error The Aquantia PHY needs 10G support +#endif + +#define AQUNTIA_10G_CTL 0x20 +#define AQUNTIA_VENDOR_P1 0xc400 + +#define AQUNTIA_SPEED_LSB_MASK 0x2000 +#define AQUNTIA_SPEED_MSB_MASK 0x40 + +int aquantia_config(struct phy_device *phydev) +{ + u32 val = phy_read(phydev, MDIO_MMD_PMAPMD, MII_BMCR); + + if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { + /* 1000BASE-T mode */ + phydev->advertising = SUPPORTED_1000baseT_Full; + phydev->supported = phydev->advertising; + + val = (val & ~AQUNTIA_SPEED_LSB_MASK) | AQUNTIA_SPEED_MSB_MASK; + phy_write(phydev, MDIO_MMD_PMAPMD, MII_BMCR, val); + } else if (phydev->interface == PHY_INTERFACE_MODE_XGMII) { + /* 10GBASE-T mode */ + phydev->advertising = SUPPORTED_10000baseT_Full; + phydev->supported = phydev->advertising; + + if (!(val & AQUNTIA_SPEED_LSB_MASK) || + !(val & AQUNTIA_SPEED_MSB_MASK)) + phy_write(phydev, MDIO_MMD_PMAPMD, MII_BMCR, + AQUNTIA_SPEED_LSB_MASK | + AQUNTIA_SPEED_MSB_MASK); + } else if (phydev->interface == PHY_INTERFACE_MODE_SGMII_2500) { + /* 2.5GBASE-T mode */ + phydev->advertising = SUPPORTED_1000baseT_Full; + phydev->supported = phydev->advertising; + + phy_write(phydev, MDIO_MMD_AN, AQUNTIA_10G_CTL, 1); + phy_write(phydev, MDIO_MMD_AN, AQUNTIA_VENDOR_P1, 0x9440); + } else if (phydev->interface == PHY_INTERFACE_MODE_MII) { + /* 100BASE-TX mode */ + phydev->advertising = SUPPORTED_100baseT_Full; + phydev->supported = phydev->advertising; + + val = (val & ~AQUNTIA_SPEED_MSB_MASK) | AQUNTIA_SPEED_LSB_MASK; + phy_write(phydev, MDIO_MMD_PMAPMD, MII_BMCR, val); + } + return 0; +} + +int aquantia_startup(struct phy_device *phydev) +{ + u32 reg, speed; + int i = 0; + + phydev->duplex = DUPLEX_FULL; + + /* if the AN is still in progress, wait till timeout. */ + phy_read(phydev, MDIO_MMD_AN, MDIO_STAT1); + reg = phy_read(phydev, MDIO_MMD_AN, MDIO_STAT1); + if (!(reg & MDIO_AN_STAT1_COMPLETE)) { + printf("%s Waiting for PHY auto negotiation to complete", + phydev->dev->name); + do { + udelay(1000); + reg = phy_read(phydev, MDIO_MMD_AN, MDIO_STAT1); + if ((i++ % 500) == 0) + printf("."); + } while (!(reg & MDIO_AN_STAT1_COMPLETE) && + i < (4 * PHY_ANEG_TIMEOUT)); + + if (i > PHY_ANEG_TIMEOUT) + printf(" TIMEOUT !\n"); + } + + /* Read twice because link state is latched and a + * read moves the current state into the register */ + phy_read(phydev, MDIO_MMD_AN, MDIO_STAT1); + reg = phy_read(phydev, MDIO_MMD_AN, MDIO_STAT1); + if (reg < 0 || !(reg & MDIO_STAT1_LSTATUS)) + phydev->link = 0; + else + phydev->link = 1; + + speed = phy_read(phydev, MDIO_MMD_PMAPMD, MII_BMCR); + if (speed & AQUNTIA_SPEED_MSB_MASK) { + if (speed & AQUNTIA_SPEED_LSB_MASK) + phydev->speed = SPEED_10000; + else + phydev->speed = SPEED_1000; + } else { + if (speed & AQUNTIA_SPEED_LSB_MASK) + phydev->speed = SPEED_100; + else + phydev->speed = SPEED_10; + } + + return 0; +} + +struct phy_driver aq1202_driver = { + .name = "Aquantia AQ1202", + .uid = 0x3a1b445, + .mask = 0xfffffff0, + .features = PHY_10G_FEATURES, + .mmds = (MDIO_MMD_PMAPMD | MDIO_MMD_PCS| + MDIO_MMD_PHYXS | MDIO_MMD_AN | + MDIO_MMD_VEND1), + .config = &aquantia_config, + .startup = &aquantia_startup, + .shutdown = &gen10g_shutdown, +}; + +struct phy_driver aq2104_driver = { + .name = "Aquantia AQ2104", + .uid = 0x3a1b460, + .mask = 0xfffffff0, + .features = PHY_10G_FEATURES, + .mmds = (MDIO_MMD_PMAPMD | MDIO_MMD_PCS| + MDIO_MMD_PHYXS | MDIO_MMD_AN | + MDIO_MMD_VEND1), + .config = &aquantia_config, + .startup = &aquantia_startup, + .shutdown = &gen10g_shutdown, +}; + +struct phy_driver aqr105_driver = { + .name = "Aquantia AQR105", + .uid = 0x3a1b4a2, + .mask = 0xfffffff0, + .features = PHY_10G_FEATURES, + .mmds = (MDIO_MMD_PMAPMD | MDIO_MMD_PCS| + MDIO_MMD_PHYXS | MDIO_MMD_AN | + MDIO_MMD_VEND1), + .config = &aquantia_config, + .startup = &aquantia_startup, + .shutdown = &gen10g_shutdown, +}; +int phy_aquantia_init(void) +{ + phy_register(&aq1202_driver); + phy_register(&aq2104_driver); + phy_register(&aqr105_driver); + + return 0; +} diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index 1d6c14f..7b75f85 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -442,6 +442,9 @@ static LIST_HEAD(phy_drivers); int phy_init(void) { +#ifdef CONFIG_PHY_AQUANTIA + phy_aquantia_init(); +#endif #ifdef CONFIG_PHY_ATHEROS phy_atheros_init(); #endif diff --git a/include/phy.h b/include/phy.h index 2fcc328..c84a441 100644 --- a/include/phy.h +++ b/include/phy.h @@ -221,6 +221,7 @@ int gen10g_startup(struct phy_device *phydev); int gen10g_shutdown(struct phy_device *phydev); int gen10g_discover_mmds(struct phy_device *phydev); +int phy_aquantia_init(void); int phy_atheros_init(void); int phy_broadcom_init(void); int phy_davicom_init(void); -- 2.1.0.27.g96db324

3 3