September 2013 - U-Boot

[U-Boot] [PATCH v1 0/5]
by Stefano Babic 02 Sep '13

02 Sep '13

Some phys have additional registers that are not covered by standard. Access to this registers can be done via specific sequence according to the phy datasheet. The driver for Micrel phy contains some additional function, that the board maintainer can call to tune the phy. However, these registers cannot be accessed with "mmdio" command. Add calback to the phy API to allow to call the function for reading / writing extended registers with the mmdio command. Stefano Babic (5): phy: add missing constants for Micrel KSZ9031 net: fix mask for phy Micrel KSZ9031 net: add extended function to phy API net: add function to read/write extended registers in Micrel Phy net: add support for extended registers to mdio command common/cmd_mdio.c | 75 ++++++++++++++++++++++++++++++++++++---------- drivers/net/phy/micrel.c | 34 ++++++++++++++++++++- include/micrel.h | 5 ++++ include/phy.h | 3 ++ 4 files changed, 100 insertions(+), 17 deletions(-) -- 1.7.9.5

2 7

[U-Boot] [PATCH] mmc:sdhci: Fix card ready status timeout.
by Przemyslaw Marczak 02 Sep '13

02 Sep '13

According to JEDEC eMMC specification, after data transfer (multiple or single block) host must wait for card ready status. This is done by waiting for command and data lines to be at idle state after transfer. JEDEC does not specify maximum timeout. Before this change max timeout was 10 ms but in case of UMS - when system do multiple read/write operations on random card blocks - timeout causes I/O errors. The timeout has been increased to 200ms after data transfer. For other transfers it stays unchanged. Tested on Goni and Trats. Signed-off-by: Przemyslaw Marczak <p.marczak(a)samsung.com> Cc: Pantelis Antoniou <panto(a)antoniou-consulting.com> --- drivers/mmc/sdhci.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/sdhci.c b/drivers/mmc/sdhci.c index 4261991..22c18d1 100644 --- a/drivers/mmc/sdhci.c +++ b/drivers/mmc/sdhci.c @@ -121,8 +121,10 @@ int sdhci_send_command(struct mmc *mmc, struct mmc_cmd *cmd, unsigned int timeout, start_addr = 0; unsigned int retry = 10000; - /* Wait max 10 ms */ - timeout = 10; + if (!data) + timeout = 200; + else + timeout = 10; sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_INT_STATUS); mask = SDHCI_CMD_INHIBIT | SDHCI_DATA_INHIBIT; -- 1.7.9.5

2 2

[U-Boot] [PATCH 1/3] arm:mmc:goni/exynos: Fix wrong mmc base register devices offset.
by Przemyslaw Marczak 02 Sep '13

02 Sep '13

On s5pc1xx mmc devices offset is multiply of 0x100000, wrong value was 0x10000. Register offset always points to mmc 0 before this change. Add macro definition of mmc dev register offset to s5pc1xx and exynos mmc. Signed-off-by: Przemyslaw Marczak <p.marczak(a)samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park(a)samsung.com> CC: Minkyu Kang <mk7.kang(a)samsung.com> --- arch/arm/include/asm/arch-exynos/mmc.h | 6 +++++- arch/arm/include/asm/arch-s5pc1xx/mmc.h | 6 +++++- 2 files changed, 10 insertions(+), 2 deletions(-) diff --git a/arch/arm/include/asm/arch-exynos/mmc.h b/arch/arm/include/asm/arch-exynos/mmc.h index 96610b8..98312d1 100644 --- a/arch/arm/include/asm/arch-exynos/mmc.h +++ b/arch/arm/include/asm/arch-exynos/mmc.h @@ -8,6 +8,8 @@ #ifndef __ASM_ARCH_MMC_H_ #define __ASM_ARCH_MMC_H_ +#define S5P_MMC_DEV_OFFSET 0x10000 + #define SDHCI_CONTROL2 0x80 #define SDHCI_CONTROL3 0x84 #define SDHCI_CONTROL4 0x8C @@ -55,7 +57,9 @@ int s5p_sdhci_init(u32 regbase, int index, int bus_width); static inline unsigned int s5p_mmc_init(int index, int bus_width) { - unsigned int base = samsung_get_base_mmc() + (0x10000 * index); + unsigned int base = samsung_get_base_mmc() + + (S5P_MMC_DEV_OFFSET * index); + return s5p_sdhci_init(base, index, bus_width); } #endif diff --git a/arch/arm/include/asm/arch-s5pc1xx/mmc.h b/arch/arm/include/asm/arch-s5pc1xx/mmc.h index 96610b8..55ff10b 100644 --- a/arch/arm/include/asm/arch-s5pc1xx/mmc.h +++ b/arch/arm/include/asm/arch-s5pc1xx/mmc.h @@ -8,6 +8,8 @@ #ifndef __ASM_ARCH_MMC_H_ #define __ASM_ARCH_MMC_H_ +#define S5P_MMC_DEV_OFFSET 0x100000 + #define SDHCI_CONTROL2 0x80 #define SDHCI_CONTROL3 0x84 #define SDHCI_CONTROL4 0x8C @@ -55,7 +57,9 @@ int s5p_sdhci_init(u32 regbase, int index, int bus_width); static inline unsigned int s5p_mmc_init(int index, int bus_width) { - unsigned int base = samsung_get_base_mmc() + (0x10000 * index); + unsigned int base = samsung_get_base_mmc() + + (S5P_MMC_DEV_OFFSET * index); + return s5p_sdhci_init(base, index, bus_width); } #endif -- 1.7.9.5

4 17

[U-Boot] [PATCH 00/10 V2] EXYNOS5420: Add SMDK5420 board support
by Rajeshwari S Shinde 02 Sep '13

02 Sep '13

This patch adds basic board support for SMDK5420 board. These patches are tested for booting fine on EVT0 SMDK5420. Changes in V2: Corrected a compilation issue for SMDK5250. Akshay Saraswat (5): Exynos5420: Add base addresses for 5420 Exynos5420: Add clock initialization for 5420 Exynos5420: Modify TZPC init to support 5420 Exynos5420: Alter UNCON and UFCON for 5420 Exynos5420: Add support for 5420 in pinmux and gpio Rajeshwari S Shinde (5): EXYNOS5: Create a common board file Exynos5420: Add DDR3 initialization for 5420 Exynos5420: Add base patch for SMDK5420 DTS: Add dts support for SMDK5420 Config: Add initial config for SMDK5420 MAINTAINERS | 1 + Makefile | 2 +- arch/arm/cpu/armv7/exynos/clock.c | 270 ++++++++- arch/arm/cpu/armv7/exynos/clock_init.h | 17 + arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 349 +++++++++++- arch/arm/cpu/armv7/exynos/dmc_common.c | 8 - arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 413 +++++++++++++- arch/arm/cpu/armv7/exynos/exynos5_setup.h | 740 +++++++++++++++++++------ arch/arm/cpu/armv7/exynos/pinmux.c | 171 +++++- arch/arm/cpu/armv7/exynos/tzpc.c | 7 +- arch/arm/dts/exynos5.dtsi | 213 +++++++ arch/arm/dts/exynos5250.dtsi | 177 +----- arch/arm/dts/exynos5420.dtsi | 74 +++ arch/arm/include/asm/arch-exynos/board.h | 17 + arch/arm/include/asm/arch-exynos/clk.h | 1 + arch/arm/include/asm/arch-exynos/clock.h | 494 +++++++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 52 +- arch/arm/include/asm/arch-exynos/dmc.h | 121 ++-- arch/arm/include/asm/arch-exynos/gpio.h | 52 ++ board/samsung/common/Makefile | 4 + board/samsung/common/board.c | 314 +++++++++++ board/samsung/dts/exynos5420-smdk5420.dts | 172 ++++++ board/samsung/smdk5250/exynos5-dt.c | 269 +-------- board/samsung/smdk5250/smdk5250.c | 182 +----- board/samsung/smdk5420/Makefile | 50 ++ board/samsung/smdk5420/smdk5420.c | 281 ++++++++++ board/samsung/smdk5420/smdk5420_spl.c | 68 +++ boards.cfg | 1 + drivers/serial/serial_s5p.c | 6 + include/configs/exynos5250-dt.h | 2 + include/configs/smdk5420.h | 316 +++++++++++ tools/Makefile | 2 + 32 files changed, 3976 insertions(+), 870 deletions(-) create mode 100644 arch/arm/dts/exynos5.dtsi create mode 100644 arch/arm/dts/exynos5420.dtsi create mode 100644 arch/arm/include/asm/arch-exynos/board.h create mode 100644 board/samsung/common/board.c create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts create mode 100644 board/samsung/smdk5420/Makefile create mode 100644 board/samsung/smdk5420/smdk5420.c create mode 100644 board/samsung/smdk5420/smdk5420_spl.c create mode 100644 include/configs/smdk5420.h -- 1.7.12.4

1 10

[U-Boot] [PATCH] net: Add fixed phy driver
by Christian Gmeiner 02 Sep '13

02 Sep '13

This patch is needed if the MAC is directly connected to a ethernet switch. In my case the FEC MAC is connected to a Micrel KSZ8895. All I need to to is configure my fixed phy/link like: Signed-off-by: Christian Gmeiner <christian.gmeiner(a)gmail.com> --- drivers/net/phy/Makefile | 1 + drivers/net/phy/fixed.c | 34 ++++++++++++++++++++++++++++++++++ drivers/net/phy/phy.c | 3 +++ 3 files changed, 38 insertions(+) create mode 100644 drivers/net/phy/fixed.c diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile index fe762e9..17e486f 100644 --- a/drivers/net/phy/Makefile +++ b/drivers/net/phy/Makefile @@ -19,6 +19,7 @@ COBJS-$(CONFIG_PHY_ATHEROS) += atheros.o COBJS-$(CONFIG_PHY_BROADCOM) += broadcom.o COBJS-$(CONFIG_PHY_DAVICOM) += davicom.o COBJS-$(CONFIG_PHY_ET1011C) += et1011c.o +COBJS-$(CONFIG_PHY_FIXED) += fixed.o COBJS-$(CONFIG_PHY_ICPLUS) += icplus.o COBJS-$(CONFIG_PHY_LXT) += lxt.o COBJS-$(CONFIG_PHY_MARVELL) += marvell.o diff --git a/drivers/net/phy/fixed.c b/drivers/net/phy/fixed.c new file mode 100644 index 0000000..70ff7bb --- /dev/null +++ b/drivers/net/phy/fixed.c @@ -0,0 +1,34 @@ +/* + * Fixed PHY driver + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Copyright 2013 Bachmann electronic GmbH + * author Gmeiner Christian + */ +#include <config.h> +#include <common.h> +#include <phy.h> + +int fixed_config(struct phy_device *phydev) +{ + phydev->link = 1; + phydev->duplex = CONFIG_PHY_FIXED_SPEED; + phydev->speed = CONFIG_PHY_FIXED_DUPLEX; + + return 0; +} + +static struct phy_driver fixed_driver = { + .uid = 0xffffffff, + .mask = 0x00000000, + .name = "Fixed PHY", + .features = 0, + .config = &fixed_config, +}; + +int phy_fixed_init(void) +{ + phy_register(&fixed_driver); + return 0; +} diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index 62925bb..f2bccaf 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -479,6 +479,9 @@ int phy_init(void) #ifdef CONFIG_PHY_VITESSE phy_vitesse_init(); #endif +#ifdef CONFIG_PHY_FIXED + phy_fixed_init(); +#endif return 0; } -- 1.7.10.4

1 0

[U-Boot] [PATCH 00/10] EXYNOS5420: Add SMDK5420 board support
by Rajeshwari S Shinde 02 Sep '13

02 Sep '13

This patch adds basic board support for SMDK5420 board. These patches are tested for booting fine on EVT0 SMDK5420. Akshay Saraswat (6): Exynos5420: Add base addresses for 5420 Exynos5420: Add clock initialization for 5420 Exynos5420: Add DDR3 initialization for 5420 Exynos5420: Modify TZPC init to support 5420 Exynos5420: Alter UNCON and UFCON for 5420 Exynos5420: Add support for 5420 in pinmux and gpio Rajeshwari S Shinde (4): EXYNOS5: Create a common board file Exynos5420: Add base patch for SMDK5420 DTS: Add dts support for SMDK5420 Config: Add initial config for SMDK5420 MAINTAINERS | 1 + Makefile | 2 +- arch/arm/cpu/armv7/exynos/clock.c | 270 ++++++++- arch/arm/cpu/armv7/exynos/clock_init.h | 17 + arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 349 +++++++++++- arch/arm/cpu/armv7/exynos/dmc_common.c | 8 - arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 411 +++++++++++++- arch/arm/cpu/armv7/exynos/exynos5_setup.h | 740 +++++++++++++++++++------ arch/arm/cpu/armv7/exynos/pinmux.c | 171 +++++- arch/arm/cpu/armv7/exynos/tzpc.c | 7 +- arch/arm/dts/exynos5.dtsi | 213 +++++++ arch/arm/dts/exynos5250.dtsi | 177 +----- arch/arm/dts/exynos5420.dtsi | 74 +++ arch/arm/include/asm/arch-exynos/board.h | 17 + arch/arm/include/asm/arch-exynos/clk.h | 1 + arch/arm/include/asm/arch-exynos/clock.h | 494 +++++++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 52 +- arch/arm/include/asm/arch-exynos/dmc.h | 121 ++-- arch/arm/include/asm/arch-exynos/gpio.h | 52 ++ board/samsung/common/Makefile | 4 + board/samsung/common/board.c | 314 +++++++++++ board/samsung/dts/exynos5420-smdk5420.dts | 172 ++++++ board/samsung/smdk5250/exynos5-dt.c | 269 +-------- board/samsung/smdk5250/smdk5250.c | 182 +----- board/samsung/smdk5420/Makefile | 50 ++ board/samsung/smdk5420/smdk5420.c | 281 ++++++++++ board/samsung/smdk5420/smdk5420_spl.c | 68 +++ boards.cfg | 1 + drivers/serial/serial_s5p.c | 6 + include/configs/exynos5250-dt.h | 2 + include/configs/smdk5420.h | 316 +++++++++++ tools/Makefile | 2 + 32 files changed, 3975 insertions(+), 869 deletions(-) create mode 100644 arch/arm/dts/exynos5.dtsi create mode 100644 arch/arm/dts/exynos5420.dtsi create mode 100644 arch/arm/include/asm/arch-exynos/board.h create mode 100644 board/samsung/common/board.c create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts create mode 100644 board/samsung/smdk5420/Makefile create mode 100644 board/samsung/smdk5420/smdk5420.c create mode 100644 board/samsung/smdk5420/smdk5420_spl.c create mode 100644 include/configs/smdk5420.h -- 1.7.12.4

1 10

[U-Boot] [RFC PATCH] armv7:omap4-common: Correct check of the SPL image size
by Oleg Kosheliev 02 Sep '13

02 Sep '13

From: Oleg_Kosheliev <oleg.kosheliev(a)ti.com> The u-boot-spl image must be stored in SRAM at addresses from 0x40300000 till 0x4030bfff. Higher than that area is located the ROM code stack. Thus we should check that the highest address of the SPL image is not in the stack area or higher. In this patch CONFIG_SPL_MAX_SIZE is corrected based on the max allowed for SPL image address. Signed-off-by: Oleg Kosheliev <oleg.kosheliev(a)ti.com> --- include/configs/omap4_common.h | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) diff --git a/include/configs/omap4_common.h b/include/configs/omap4_common.h index 2fa4382..aeeef6c 100644 --- a/include/configs/omap4_common.h +++ b/include/configs/omap4_common.h @@ -266,7 +266,14 @@ #define CONFIG_SPL #define CONFIG_SPL_FRAMEWORK #define CONFIG_SPL_TEXT_BASE 0x40304350 -#define CONFIG_SPL_MAX_SIZE (38 * 1024) +/* + * The allowed space in SRAM for SPL is from 0x40300000 till 0x4030bfff. + * The space above 0x4030c000 is used by ROM code stack + * and this area must not be rewritten by the SPL + */ +#define CONFIG_SPL_MAX_ADDR 0x4030bfff +#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_MAX_ADDR - \ + CONFIG_SPL_TEXT_BASE) #define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR #define CONFIG_SPL_DISPLAY_PRINT -- 1.7.9.5

3 2

[U-Boot] [PATCH 1/2] ARM: IGEP0033: rename config file to am335x_igep0033.h
by Javier Martinez Canillas 02 Sep '13

02 Sep '13

There seems to be a naming convention for the configuration files for boards using the same SoC family. This makes easier to do changes that affect different boards based on the same SoC. Since the IGEP COM AQUILA use an AM3352/AM3354 processor is better to rename its board config to use this naming scheme. Signed-off-by: Javier Martinez Canillas <javier.martinez(a)collabora.co.uk> --- boards.cfg | 2 +- include/configs/am335x_igep0033.h | 291 +++++++++++++++++++++++++++++++++++++ include/configs/igep0033.h | 291 ------------------------------------- 3 files changed, 292 insertions(+), 292 deletions(-) create mode 100644 include/configs/am335x_igep0033.h delete mode 100644 include/configs/igep0033.h diff --git a/boards.cfg b/boards.cfg index 7ccc7ce..d717226 100644 --- a/boards.cfg +++ b/boards.cfg @@ -302,7 +302,7 @@ igep0020_nand arm armv7 igep00x0 isee igep0030 arm armv7 igep00x0 isee omap3 igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_ONENAND igep0030_nand arm armv7 igep00x0 isee omap3 igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_NAND igep0032 arm armv7 igep00x0 isee omap3 igep00x0:MACH_TYPE=MACH_TYPE_IGEP0032,BOOT_ONENAND -igep0033 arm armv7 igep0033 isee am33xx +am335x_igep0033 arm armv7 igep0033 isee am33xx am3517_evm arm armv7 am3517evm logicpd omap3 mt_ventoux arm armv7 mt_ventoux teejet omap3 omap3_zoom1 arm armv7 zoom1 logicpd omap3 diff --git a/include/configs/am335x_igep0033.h b/include/configs/am335x_igep0033.h new file mode 100644 index 0000000..e08fc14 --- /dev/null +++ b/include/configs/am335x_igep0033.h @@ -0,0 +1,291 @@ +/* + * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/ + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation version 2. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __CONFIG_IGEP0033_H +#define __CONFIG_IGEP0033_H + +#define CONFIG_AM33XX +#define CONFIG_OMAP +#define CONFIG_OMAP_COMMON + +#include <asm/arch/omap.h> + +/* Mach type */ +#define MACH_TYPE_IGEP0033 4521 /* Until the next sync */ +#define CONFIG_MACH_TYPE MACH_TYPE_IGEP0033 + +/* Clock defines */ +#define V_OSCK 24000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK) + +#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ +#define CONFIG_SYS_MALLOC_LEN (1024 << 10) +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_PROMPT "U-Boot# " +#define CONFIG_SYS_NO_FLASH + +/* Display cpuinfo */ +#define CONFIG_DISPLAY_CPUINFO + +/* Flattened Device Tree */ +#define CONFIG_OF_LIBFDT + +/* Commands to include */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_BOOTZ +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ECHO +#define CONFIG_CMD_EXT4 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_FS_GENERIC +#define CONFIG_CMD_MMC +#define CONFIG_CMD_MTDPARTS +#define CONFIG_CMD_NAND +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS + +/* Make the verbose messages from UBI stop printing */ +#define CONFIG_UBI_SILENCE_MSG +#define CONFIG_UBIFS_SILENCE_MSG + +#define CONFIG_BOOTDELAY 1 /* negative for no autoboot */ +#define CONFIG_ENV_VARS_UBOOT_CONFIG +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG +#define CONFIG_EXTRA_ENV_SETTINGS \ + "loadaddr=0x80F80000\0" \ + "dtbaddr=0x80200000\0" \ + "bootdir=/boot\0" \ + "bootfile=zImage\0" \ + "dtbfile=am335x-base0033.dtb\0" \ + "console=ttyO0,115200n8\0" \ + "mtdids=" MTDIDS_DEFAULT "\0" \ + "mtdparts=" MTDPARTS_DEFAULT "\0" \ + "mmcdev=0\0" \ + "mmcroot=/dev/mmcblk0p2 rw\0" \ + "ubiroot=ubi0:filesystem rw ubi.mtd=3,2048\0" \ + "mmcrootfstype=ext4 rootwait\0" \ + "ubirootfstype=ubifs rootwait\0" \ + "mmcargs=setenv bootargs console=${console} " \ + "root=${mmcroot} " \ + "rootfstype=${mmcrootfstype}\0" \ + "ubiargs=setenv bootargs console=${console} " \ + "root=${ubiroot} " \ + "rootfstype=${ubirootfstype}\0" \ + "bootenv=uEnv.txt\0" \ + "loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \ + "importbootenv=echo Importing environment from mmc ...; " \ + "env import -t ${loadaddr} ${filesize}\0" \ + "mmcload=load mmc ${mmcdev}:2 ${loadaddr} ${bootdir}/${bootfile}; " \ + "load mmc ${mmcdev}:2 ${dtbaddr} ${bootdir}/${dtbfile}\0" \ + "ubiload=ubi part filesystem 2048; ubifsmount ubi0; " \ + "ubifsload ${loadaddr} ${bootdir}/${bootfile}; " \ + "ubifsload ${dtbaddr} ${bootdir}/${dtbfile} \0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "bootz ${loadaddr} - ${dtbaddr}\0" \ + "ubiboot=echo Booting from nand (ubifs) ...; " \ + "run ubiargs; run ubiload; " \ + "bootz ${loadaddr} - ${dtbaddr}\0" \ + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "echo SD/MMC found on device ${mmcdev};" \ + "if run loadbootenv; then " \ + "echo Loaded environment from ${bootenv};" \ + "run importbootenv;" \ + "fi;" \ + "if test -n $uenvcmd; then " \ + "echo Running uenvcmd ...;" \ + "run uenvcmd;" \ + "fi;" \ + "if run mmcload; then " \ + "run mmcboot;" \ + "fi;" \ + "else " \ + "run ubiboot;" \ + "fi;" \ + +/* Max number of command args */ +#define CONFIG_SYS_MAXARGS 16 + +/* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 512 + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ + + sizeof(CONFIG_SYS_PROMPT) + 16) + +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_LOAD_ADDR 0x81000000 /* Default load address */ + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ +#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ + +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ + GENERATED_GBL_DATA_SIZE) +/* Platform/Board specific defs */ +#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */ +#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ +#define CONFIG_SYS_HZ 1000 /* 1ms clock */ + +/* NS16550 Configuration */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK (48000000) +#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */ + +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 + +/* CPU */ +#define CONFIG_ARCH_CPU_INIT + +#define CONFIG_ENV_OVERWRITE 1 +#define CONFIG_SYS_CONSOLE_INFO_QUIET + +/* MMC support */ +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_OMAP_HSMMC +#define CONFIG_DOS_PARTITION + +/* GPIO support */ +#define CONFIG_OMAP_GPIO + +/* Ethernet support */ +#define CONFIG_DRIVER_TI_CPSW +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_NET_MULTI +#define CONFIG_PHYLIB +#define CONFIG_PHY_ADDR 0 +#define CONFIG_PHY_SMSC + +/* NAND support */ +#define CONFIG_NAND +#define CONFIG_NAND_OMAP_GPMC +#define GPMC_NAND_ECC_LP_x16_LAYOUT 1 +#define CONFIG_SYS_NAND_BASE (0x08000000) /* phys address CS0 */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_ONFI_DETECTION 1 +#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x180000 /* environment starts here */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_OFFSET + CONFIG_SYS_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +#define CONFIG_MTD_PARTITIONS +#define CONFIG_MTD_DEVICE +#define CONFIG_RBTREE +#define CONFIG_LZO + +#define MTDIDS_DEFAULT "nand0=omap2-nand.0" +#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(spl),"\ + "1m(uboot),256k(environment),"\ + "-(filesystem)" + +/* Unsupported features */ +#undef CONFIG_USE_IRQ + +/* Defines for SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK +/* + * Place the image at the start of the ROM defined image space. + * We limit our size to the ROM-defined downloaded image area, and use the + * rest of the space for stack. + */ +#define CONFIG_SPL_TEXT_BASE 0x402F0400 +#define CONFIG_SPL_MAX_SIZE (0x4030C000 - CONFIG_SPL_TEXT_BASE) +#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR + +#define CONFIG_SPL_BSS_START_ADDR 0x80000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ + +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ +#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1 +#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_GPIO_SUPPORT +#define CONFIG_SPL_YMODEM_SUPPORT +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds" + +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_NAND_AM33XX_BCH +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ + CONFIG_SYS_NAND_PAGE_SIZE) +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \ + 10, 11, 12, 13, 14, 15, 16, 17, \ + 18, 19, 20, 21, 22, 23, 24, 25, \ + 26, 27, 28, 29, 30, 31, 32, 33, \ + 34, 35, 36, 37, 38, 39, 40, 41, \ + 42, 43, 44, 45, 46, 47, 48, 49, \ + 50, 51, 52, 53, 54, 55, 56, 57, } + +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 14 + +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE + +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 + +/* + * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM + * 64 bytes before this address should be set aside for u-boot.img's + * header. That is 0x800FFFC0--0x80100000 should not be used for any + * other needs. + */ +#define CONFIG_SYS_TEXT_BASE 0x80800000 +#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 + +/* + * Since SPL did pll and ddr initialization for us, + * we don't need to do it twice. + */ +#ifndef CONFIG_SPL_BUILD +#define CONFIG_SKIP_LOWLEVEL_INIT +#endif + +#endif /* ! __CONFIG_IGEP0033_H */ diff --git a/include/configs/igep0033.h b/include/configs/igep0033.h deleted file mode 100644 index e08fc14..0000000 --- a/include/configs/igep0033.h +++ /dev/null @@ -1,291 +0,0 @@ -/* - * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/ - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation version 2. - * - * This program is distributed "as is" WITHOUT ANY WARRANTY of any - * kind, whether express or implied; without even the implied warranty - * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - */ - -#ifndef __CONFIG_IGEP0033_H -#define __CONFIG_IGEP0033_H - -#define CONFIG_AM33XX -#define CONFIG_OMAP -#define CONFIG_OMAP_COMMON - -#include <asm/arch/omap.h> - -/* Mach type */ -#define MACH_TYPE_IGEP0033 4521 /* Until the next sync */ -#define CONFIG_MACH_TYPE MACH_TYPE_IGEP0033 - -/* Clock defines */ -#define V_OSCK 24000000 /* Clock output from T2 */ -#define V_SCLK (V_OSCK) - -#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ -#define CONFIG_SYS_MALLOC_LEN (1024 << 10) -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ -#define CONFIG_SYS_PROMPT "U-Boot# " -#define CONFIG_SYS_NO_FLASH - -/* Display cpuinfo */ -#define CONFIG_DISPLAY_CPUINFO - -/* Flattened Device Tree */ -#define CONFIG_OF_LIBFDT - -/* Commands to include */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_BOOTZ -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_EXT4 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_FS_GENERIC -#define CONFIG_CMD_MMC -#define CONFIG_CMD_MTDPARTS -#define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_PING -#define CONFIG_CMD_UBI -#define CONFIG_CMD_UBIFS - -/* Make the verbose messages from UBI stop printing */ -#define CONFIG_UBI_SILENCE_MSG -#define CONFIG_UBIFS_SILENCE_MSG - -#define CONFIG_BOOTDELAY 1 /* negative for no autoboot */ -#define CONFIG_ENV_VARS_UBOOT_CONFIG -#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG -#define CONFIG_EXTRA_ENV_SETTINGS \ - "loadaddr=0x80F80000\0" \ - "dtbaddr=0x80200000\0" \ - "bootdir=/boot\0" \ - "bootfile=zImage\0" \ - "dtbfile=am335x-base0033.dtb\0" \ - "console=ttyO0,115200n8\0" \ - "mtdids=" MTDIDS_DEFAULT "\0" \ - "mtdparts=" MTDPARTS_DEFAULT "\0" \ - "mmcdev=0\0" \ - "mmcroot=/dev/mmcblk0p2 rw\0" \ - "ubiroot=ubi0:filesystem rw ubi.mtd=3,2048\0" \ - "mmcrootfstype=ext4 rootwait\0" \ - "ubirootfstype=ubifs rootwait\0" \ - "mmcargs=setenv bootargs console=${console} " \ - "root=${mmcroot} " \ - "rootfstype=${mmcrootfstype}\0" \ - "ubiargs=setenv bootargs console=${console} " \ - "root=${ubiroot} " \ - "rootfstype=${ubirootfstype}\0" \ - "bootenv=uEnv.txt\0" \ - "loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \ - "importbootenv=echo Importing environment from mmc ...; " \ - "env import -t ${loadaddr} ${filesize}\0" \ - "mmcload=load mmc ${mmcdev}:2 ${loadaddr} ${bootdir}/${bootfile}; " \ - "load mmc ${mmcdev}:2 ${dtbaddr} ${bootdir}/${dtbfile}\0" \ - "ubiload=ubi part filesystem 2048; ubifsmount ubi0; " \ - "ubifsload ${loadaddr} ${bootdir}/${bootfile}; " \ - "ubifsload ${dtbaddr} ${bootdir}/${dtbfile} \0" \ - "mmcboot=echo Booting from mmc ...; " \ - "run mmcargs; " \ - "bootz ${loadaddr} - ${dtbaddr}\0" \ - "ubiboot=echo Booting from nand (ubifs) ...; " \ - "run ubiargs; run ubiload; " \ - "bootz ${loadaddr} - ${dtbaddr}\0" \ - -#define CONFIG_BOOTCOMMAND \ - "mmc dev ${mmcdev}; if mmc rescan; then " \ - "echo SD/MMC found on device ${mmcdev};" \ - "if run loadbootenv; then " \ - "echo Loaded environment from ${bootenv};" \ - "run importbootenv;" \ - "fi;" \ - "if test -n $uenvcmd; then " \ - "echo Running uenvcmd ...;" \ - "run uenvcmd;" \ - "fi;" \ - "if run mmcload; then " \ - "run mmcboot;" \ - "fi;" \ - "else " \ - "run ubiboot;" \ - "fi;" \ - -/* Max number of command args */ -#define CONFIG_SYS_MAXARGS 16 - -/* Console I/O Buffer Size */ -#define CONFIG_SYS_CBSIZE 512 - -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - + sizeof(CONFIG_SYS_PROMPT) + 16) - -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE -#define CONFIG_SYS_LOAD_ADDR 0x81000000 /* Default load address */ - -/* Physical Memory Map */ -#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ -#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ - -#define CONFIG_SYS_SDRAM_BASE 0x80000000 -#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ - GENERATED_GBL_DATA_SIZE) -/* Platform/Board specific defs */ -#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */ -#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ -#define CONFIG_SYS_HZ 1000 /* 1ms clock */ - -/* NS16550 Configuration */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK (48000000) -#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */ - -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 115200 - -/* CPU */ -#define CONFIG_ARCH_CPU_INIT - -#define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_SYS_CONSOLE_INFO_QUIET - -/* MMC support */ -#define CONFIG_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_OMAP_HSMMC -#define CONFIG_DOS_PARTITION - -/* GPIO support */ -#define CONFIG_OMAP_GPIO - -/* Ethernet support */ -#define CONFIG_DRIVER_TI_CPSW -#define CONFIG_MII -#define CONFIG_BOOTP_DEFAULT -#define CONFIG_BOOTP_DNS -#define CONFIG_BOOTP_DNS2 -#define CONFIG_BOOTP_SEND_HOSTNAME -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_NET_RETRY_COUNT 10 -#define CONFIG_NET_MULTI -#define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 0 -#define CONFIG_PHY_SMSC - -/* NAND support */ -#define CONFIG_NAND -#define CONFIG_NAND_OMAP_GPMC -#define GPMC_NAND_ECC_LP_x16_LAYOUT 1 -#define CONFIG_SYS_NAND_BASE (0x08000000) /* phys address CS0 */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_ONFI_DETECTION 1 -#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ -#define CONFIG_SYS_REDUNDAND_ENVIRONMENT -#define CONFIG_ENV_IS_IN_NAND -#define CONFIG_ENV_OFFSET 0x180000 /* environment starts here */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_OFFSET + CONFIG_SYS_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#define CONFIG_MTD_PARTITIONS -#define CONFIG_MTD_DEVICE -#define CONFIG_RBTREE -#define CONFIG_LZO - -#define MTDIDS_DEFAULT "nand0=omap2-nand.0" -#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(spl),"\ - "1m(uboot),256k(environment),"\ - "-(filesystem)" - -/* Unsupported features */ -#undef CONFIG_USE_IRQ - -/* Defines for SPL */ -#define CONFIG_SPL -#define CONFIG_SPL_FRAMEWORK -/* - * Place the image at the start of the ROM defined image space. - * We limit our size to the ROM-defined downloaded image area, and use the - * rest of the space for stack. - */ -#define CONFIG_SPL_TEXT_BASE 0x402F0400 -#define CONFIG_SPL_MAX_SIZE (0x4030C000 - CONFIG_SPL_TEXT_BASE) -#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR - -#define CONFIG_SPL_BSS_START_ADDR 0x80000000 -#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ - -#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ -#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ -#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1 -#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" -#define CONFIG_SPL_MMC_SUPPORT -#define CONFIG_SPL_FAT_SUPPORT -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBDISK_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_SERIAL_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT -#define CONFIG_SPL_YMODEM_SUPPORT -#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds" - -#define CONFIG_SPL_BOARD_INIT -#define CONFIG_SPL_NAND_AM33XX_BCH -#define CONFIG_SPL_NAND_SUPPORT -#define CONFIG_SPL_NAND_BASE -#define CONFIG_SPL_NAND_DRIVERS -#define CONFIG_SPL_NAND_ECC -#define CONFIG_SYS_NAND_5_ADDR_CYCLE -#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ - CONFIG_SYS_NAND_PAGE_SIZE) -#define CONFIG_SYS_NAND_PAGE_SIZE 2048 -#define CONFIG_SYS_NAND_OOBSIZE 64 -#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) -#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS -#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \ - 10, 11, 12, 13, 14, 15, 16, 17, \ - 18, 19, 20, 21, 22, 23, 24, 25, \ - 26, 27, 28, 29, 30, 31, 32, 33, \ - 34, 35, 36, 37, 38, 39, 40, 41, \ - 42, 43, 44, 45, 46, 47, 48, 49, \ - 50, 51, 52, 53, 54, 55, 56, 57, } - -#define CONFIG_SYS_NAND_ECCSIZE 512 -#define CONFIG_SYS_NAND_ECCBYTES 14 - -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE - -#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 - -/* - * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM - * 64 bytes before this address should be set aside for u-boot.img's - * header. That is 0x800FFFC0--0x80100000 should not be used for any - * other needs. - */ -#define CONFIG_SYS_TEXT_BASE 0x80800000 -#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 -#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 - -/* - * Since SPL did pll and ddr initialization for us, - * we don't need to do it twice. - */ -#ifndef CONFIG_SPL_BUILD -#define CONFIG_SKIP_LOWLEVEL_INIT -#endif - -#endif /* ! __CONFIG_IGEP0033_H */ -- 1.7.10.4

2 3

[U-Boot] [PATCH] powerpc/p1010rdb: add p1010rdb-pb support with updating p1010rdb-pa
by Shengzhou Liu 02 Sep '13

02 Sep '13

- Rename old P1010RDB board as P1010RDB-PA. - Add support for new P1010RDB-PB board. - Enable IFC flash access in case of SD boot. - Some optimization and code cleanup. Only P1010RDB-PB board is supported officially, but we still reserve code-support for previous P1010RDB-PA board. Signed-off-by: Shengzhou Liu <Shengzhou.Liu(a)freescale.com> --- board/freescale/p1010rdb/law.c | 2 - board/freescale/p1010rdb/p1010rdb.c | 330 ++++++++++++++++++++++++++++++------ board/freescale/p1010rdb/tlb.c | 4 - boards.cfg | 41 +++-- include/configs/P1010RDB.h | 113 +++++++++--- 5 files changed, 389 insertions(+), 101 deletions(-) diff --git a/board/freescale/p1010rdb/law.c b/board/freescale/p1010rdb/law.c index 0045127..ed41a05 100644 --- a/board/freescale/p1010rdb/law.c +++ b/board/freescale/p1010rdb/law.c @@ -9,11 +9,9 @@ #include <asm/mmu.h> struct law_entry law_table[] = { -#ifndef CONFIG_SDCARD SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_IFC), SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_IFC), SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC), -#endif }; int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/p1010rdb/p1010rdb.c b/board/freescale/p1010rdb/p1010rdb.c index 06aa800..2fd7790 100644 --- a/board/freescale/p1010rdb/p1010rdb.c +++ b/board/freescale/p1010rdb/p1010rdb.c @@ -21,10 +21,8 @@ #include <asm/fsl_serdes.h> #include <asm/fsl_ifc.h> #include <asm/fsl_pci.h> - -#ifndef CONFIG_SDCARD #include <hwconfig.h> -#endif +#include <i2c.h> DECLARE_GLOBAL_DATA_PTR; @@ -33,10 +31,30 @@ DECLARE_GLOBAL_DATA_PTR; #define MUX_CPLD_TDM 0x01 #define MUX_CPLD_SPICS0_FLASH 0x00 #define MUX_CPLD_SPICS0_SLIC 0x02 +#define PMUXCR1_IFC_MASK 0x00ffff00 +#define PMUXCR1_SDHC_MASK 0x00fff000 +#define PMUXCR1_SDHC_ENABLE 0x00555000 + +enum { + MUX_TYPE_IFC, + MUX_TYPE_SDHC, + MUX_TYPE_SPIFLASH, + MUX_TYPE_TDM, + MUX_TYPE_CAN, + MUX_TYPE_CS0_NOR, + MUX_TYPE_CS0_NAND, +}; + +enum { + I2C_READ_BANK, + I2C_READ_PCB_VER, +}; + +static uint sd_ifc_mux; -#ifndef CONFIG_SDCARD struct cpld_data { u8 cpld_ver; /* cpld revision */ +#if defined(CONFIG_P1010RDB_PA) u8 pcba_ver; /* pcb revision number */ u8 twindie_ddr3; u8 res1[6]; @@ -51,53 +69,18 @@ struct cpld_data { u8 por1; /* POR Options */ u8 por2; /* POR Options */ u8 por3; /* POR Options */ -}; - -void cpld_show(void) -{ - struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); - - printf("CPLD: V%x.%x PCBA: V%x.0\n", - in_8(&cpld_data->cpld_ver) & 0xF0, - in_8(&cpld_data->cpld_ver) & 0x0F, - in_8(&cpld_data->pcba_ver) & 0x0F); - -#ifdef CONFIG_DEBUG - printf("twindie_ddr =%x\n", - in_8(&cpld_data->twindie_ddr3)); - printf("bank_sel =%x\n", - in_8(&cpld_data->bank_sel)); - printf("usb2_sel =%x\n", - in_8(&cpld_data->usb2_sel)); - printf("porsw_sel =%x\n", - in_8(&cpld_data->porsw_sel)); - printf("tdm_can_sel =%x\n", - in_8(&cpld_data->tdm_can_sel)); - printf("tdm_can_sel =%x\n", - in_8(&cpld_data->tdm_can_sel)); - printf("spi_cs0_sel =%x\n", - in_8(&cpld_data->spi_cs0_sel)); - printf("bcsr0 =%x\n", - in_8(&cpld_data->bcsr0)); - printf("bcsr1 =%x\n", - in_8(&cpld_data->bcsr1)); - printf("bcsr2 =%x\n", - in_8(&cpld_data->bcsr2)); - printf("bcsr3 =%x\n", - in_8(&cpld_data->bcsr3)); -#endif -} +#elif defined(CONFIG_P1010RDB_PB) + u8 rom_loc; #endif +}; int board_early_init_f(void) { ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR); -#ifndef CONFIG_SDCARD struct fsl_ifc *ifc = (void *)CONFIG_SYS_IFC_ADDR; /* Clock configuration to access CPLD using IFC(GPCM) */ setbits_be32(&ifc->ifc_gcr, 1 << IFC_GCR_TBCTL_TRN_TIME_SHIFT); -#endif /* * Reset PCIe slots via GPIO4 */ @@ -109,7 +92,6 @@ int board_early_init_f(void) int board_early_init_r(void) { -#ifndef CONFIG_SDCARD const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); @@ -133,7 +115,7 @@ int board_early_init_r(void) CONFIG_SYS_FLASH_BASE_PHYS + 0x1000000, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, flash_esel+1, BOOKE_PAGESZ_16M, 1); -#endif + return 0; } @@ -144,13 +126,201 @@ void pci_init_board(void) } #endif /* ifdef CONFIG_PCI */ +int config_board_mux(int ctrl_type) +{ + ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u8 tmp; + +#if defined(CONFIG_P1010RDB_PA) + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + + switch (ctrl_type) { + case MUX_TYPE_IFC: + i2c_set_bus_num(I2C_PCA9557_BUS_NUM); + tmp = 0xf0; + i2c_write(I2C_PCA9557_ADDR1, 3, 1, &tmp, 1); + tmp = 0x01; + i2c_write(I2C_PCA9557_ADDR1, 1, 1, &tmp, 1); + sd_ifc_mux = MUX_TYPE_IFC; + clrbits_be32(&gur->pmuxcr, PMUXCR1_IFC_MASK); + debug("pin mux is configured for IFC, SDHC disabled\n"); + break; + case MUX_TYPE_SDHC: + i2c_set_bus_num(I2C_PCA9557_BUS_NUM); + tmp = 0xf0; + i2c_write(I2C_PCA9557_ADDR1, 3, 1, &tmp, 1); + tmp = 0x05; + i2c_write(I2C_PCA9557_ADDR1, 1, 1, &tmp, 1); + sd_ifc_mux = MUX_TYPE_SDHC; + clrsetbits_be32(&gur->pmuxcr, PMUXCR1_SDHC_MASK, + PMUXCR1_SDHC_ENABLE); + debug("pin mux is configured for SDHC, IFC disabled\n"); + break; + case MUX_TYPE_SPIFLASH: + out_8(&cpld_data->spi_cs0_sel, MUX_CPLD_SPICS0_FLASH); + break; + case MUX_TYPE_TDM: + out_8(&cpld_data->tdm_can_sel, MUX_CPLD_TDM); + out_8(&cpld_data->spi_cs0_sel, MUX_CPLD_SPICS0_SLIC); + break; + case MUX_TYPE_CAN: + out_8(&cpld_data->tdm_can_sel, MUX_CPLD_CAN_UART); + break; + default: + break; + } +#elif defined(CONFIG_P1010RDB_PB) + uint orig_bus = i2c_get_bus_num(); + i2c_set_bus_num(I2C_PCA9557_BUS_NUM); + + switch (ctrl_type) { + case MUX_TYPE_IFC: + i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); + clrbits_8(&tmp, 0x04); + i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); + i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + clrbits_8(&tmp, 0x04); + i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + sd_ifc_mux = MUX_TYPE_IFC; + clrbits_be32(&gur->pmuxcr, PMUXCR1_IFC_MASK); + break; + case MUX_TYPE_SDHC: + i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); + setbits_8(&tmp, 0x04); + i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); + i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + clrbits_8(&tmp, 0x04); + i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + sd_ifc_mux = MUX_TYPE_SDHC; + clrsetbits_be32(&gur->pmuxcr, PMUXCR1_SDHC_MASK, + PMUXCR1_SDHC_ENABLE); + break; + case MUX_TYPE_SPIFLASH: + i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); + clrbits_8(&tmp, 0x80); + i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); + i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + clrbits_8(&tmp, 0x80); + i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + break; + case MUX_TYPE_TDM: + i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); + setbits_8(&tmp, 0x82); + i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); + i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + clrbits_8(&tmp, 0x82); + i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + break; + case MUX_TYPE_CAN: + i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); + clrbits_8(&tmp, 0x02); + i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); + i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + clrbits_8(&tmp, 0x02); + i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + break; + case MUX_TYPE_CS0_NOR: + i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); + clrbits_8(&tmp, 0x08); + i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); + i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + clrbits_8(&tmp, 0x08); + i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + break; + case MUX_TYPE_CS0_NAND: + i2c_read(I2C_PCA9557_ADDR2, 0, 1, &tmp, 1); + setbits_8(&tmp, 0x08); + i2c_write(I2C_PCA9557_ADDR2, 1, 1, &tmp, 1); + i2c_read(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + clrbits_8(&tmp, 0x08); + i2c_write(I2C_PCA9557_ADDR2, 3, 1, &tmp, 1); + break; + default: + break; + } + i2c_set_bus_num(orig_bus); +#endif + return 0; +} + +#ifdef CONFIG_P1010RDB_PB +int i2c_pca9557_read(int type) +{ + u8 val; + + i2c_set_bus_num(I2C_PCA9557_BUS_NUM); + i2c_read(I2C_PCA9557_ADDR2, 0, 1, &val, 1); + + switch (type) { + case I2C_READ_BANK: + val = (val & 0x10) >> 4; + break; + case I2C_READ_PCB_VER: + val = ((val & 0x60) >> 5) + 1; + break; + default: + break; + } + + return val; +} +#endif + int checkboard(void) { struct cpu_type *cpu; + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + u8 val; cpu = gd->arch.cpu; - printf("Board: %sRDB\n", cpu->name); +#if defined(CONFIG_P1010RDB_PA) + printf("Board: %sRDB-PA, ", cpu->name); +#elif defined(CONFIG_P1010RDB_PB) + printf("Board: %sRDB-PB, ", cpu->name); + i2c_set_bus_num(I2C_PCA9557_BUS_NUM); + i2c_init(CONFIG_SYS_FSL_I2C_SPEED, CONFIG_SYS_FSL_I2C_SLAVE); + val = 0x0; /* no polarity inversion */ + i2c_write(I2C_PCA9557_ADDR2, 2, 1, &val, 1); +#endif + +#ifdef CONFIG_SDCARD + /* switch to IFC to read info from CPLD */ + config_board_mux(MUX_TYPE_IFC); +#endif +#if defined(CONFIG_P1010RDB_PA) + val = (in_8(&cpld_data->pcba_ver) & 0xF); + printf("PCB: v%x.0\n", val); +#elif defined(CONFIG_P1010RDB_PB) + val = in_8(&cpld_data->cpld_ver); + printf("CPLD: v%x.%x, ", val >> 4, val & 0xf); + printf("PCB: v%x.0, ", i2c_pca9557_read(I2C_READ_PCB_VER)); + val = in_8(&cpld_data->rom_loc) & 0xf; + puts("Boot from: "); + switch (val) { + case 0xf: + config_board_mux(MUX_TYPE_CS0_NOR); + printf("NOR vBank%d\n", i2c_pca9557_read(I2C_READ_BANK)); + break; + case 0xe: + puts("SDHC\n"); + val = 0x60; /* set pca9557 pin input/output */ + i2c_write(I2C_PCA9557_ADDR2, 3, 1, &val, 1); + break; + case 0x5: + config_board_mux(MUX_TYPE_IFC); + config_board_mux(MUX_TYPE_CS0_NAND); + puts("NAND\n"); + break; + case 0x6: + config_board_mux(MUX_TYPE_IFC); + puts("SPI\n"); + break; + default: + puts("unknown\n"); + break; + } +#endif return 0; } @@ -246,6 +416,16 @@ void fdt_del_sdhc(void *blob) } } +void fdt_del_ifc(void *blob) +{ + int nodeoff = 0; + + while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, + "fsl,ifc")) >= 0) { + fdt_del_node(blob, nodeoff); + } +} + void fdt_disable_uart1(void *blob) { int nodeoff; @@ -289,9 +469,13 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_del_flexcan(blob); fdt_del_node_and_alias(blob, "ethernet2"); } -#ifndef CONFIG_SDCARD - /* disable sdhc due to sdhc bug */ - fdt_del_sdhc(blob); + + /* Delete IFC node as IFC pins are multiplexing with SDHC */ + if (sd_ifc_mux != MUX_TYPE_IFC) + fdt_del_ifc(blob); + else + fdt_del_sdhc(blob); + if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "can")) { fdt_del_tdm(blob); fdt_del_spi_slic(blob); @@ -309,14 +493,26 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_del_flexcan(blob); fdt_disable_uart1(blob); } +} #endif + +#ifdef CONFIG_SDCARD +int board_mmc_init(bd_t *bis) +{ + config_board_mux(MUX_TYPE_SDHC); + return -1; +} +#else +void board_reset(void) +{ + /* mux to IFC to enable CPLD for reset */ + if (sd_ifc_mux != MUX_TYPE_IFC) + config_board_mux(MUX_TYPE_IFC); } #endif -#ifndef CONFIG_SDCARD int misc_init_r(void) { - struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "can")) { @@ -324,7 +520,7 @@ int misc_init_r(void) MPC85xx_PMUXCR_CAN1_UART | MPC85xx_PMUXCR_CAN2_TDM | MPC85xx_PMUXCR_CAN2_UART); - out_8(&cpld_data->tdm_can_sel, MUX_CPLD_CAN_UART); + config_board_mux(MUX_TYPE_CAN); } else if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) { clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN2_UART | MPC85xx_PMUXCR_CAN1_UART); @@ -332,13 +528,37 @@ int misc_init_r(void) MPC85xx_PMUXCR_CAN1_TDM); clrbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_GPIO); setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_TDM); - out_8(&cpld_data->tdm_can_sel, MUX_CPLD_TDM); - out_8(&cpld_data->spi_cs0_sel, MUX_CPLD_SPICS0_SLIC); + config_board_mux(MUX_TYPE_TDM); } else { /* defaultly spi_cs_sel to flash */ - out_8(&cpld_data->spi_cs0_sel, MUX_CPLD_SPICS0_FLASH); + config_board_mux(MUX_TYPE_SPIFLASH); } + if (hwconfig("esdhc")) + config_board_mux(MUX_TYPE_SDHC); + +#ifdef CONFIG_P1010RDB_PB + setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_GPIO01_DRVVBUS); +#endif return 0; } -#endif + +static int pin_mux_cmd(cmd_tbl_t *cmdtp, int flag, int argc, + char * const argv[]) +{ + if (argc < 2) + return CMD_RET_USAGE; + if (strcmp(argv[1], "ifc") == 0) + config_board_mux(MUX_TYPE_IFC); + else if (strcmp(argv[1], "sdhc") == 0) + config_board_mux(MUX_TYPE_SDHC); + else + return CMD_RET_USAGE; + return 0; +} + +U_BOOT_CMD( + mux, 2, 0, pin_mux_cmd, + "configure multiplexing pin for IFC/SDHC bus in runtime", + "bus_type (e.g. mux sdhc)" +); diff --git a/board/freescale/p1010rdb/tlb.c b/board/freescale/p1010rdb/tlb.c index 77a8043..a7af0f6 100644 --- a/board/freescale/p1010rdb/tlb.c +++ b/board/freescale/p1010rdb/tlb.c @@ -42,7 +42,6 @@ struct fsl_e_tlb_entry tlb_table[] = { 0, 1, BOOKE_PAGESZ_1M, 1), #ifndef CONFIG_SPL_BUILD -#ifndef CONFIG_SDCARD SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, 0, 2, BOOKE_PAGESZ_16M, 1), @@ -51,7 +50,6 @@ struct fsl_e_tlb_entry tlb_table[] = { CONFIG_SYS_FLASH_BASE_PHYS + 0x1000000, MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, 0, 3, BOOKE_PAGESZ_16M, 1), -#endif #ifdef CONFIG_PCI /* *I*G* - PCI */ @@ -66,7 +64,6 @@ struct fsl_e_tlb_entry tlb_table[] = { #endif #endif -#ifndef CONFIG_SDCARD /* *I*G - Board CPLD */ SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS, MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, @@ -75,7 +72,6 @@ struct fsl_e_tlb_entry tlb_table[] = { SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 7, BOOKE_PAGESZ_1M, 1), -#endif #if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_SPL) SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, diff --git a/boards.cfg b/boards.cfg index be810c7..e2d3cdc 100644 --- a/boards.cfg +++ b/boards.cfg @@ -783,21 +783,32 @@ MPC8572DS_36BIT powerpc mpc85xx mpc8572ds freesca MPC8572DS_NAND powerpc mpc85xx mpc8572ds freescale - MPC8572DS:NAND C29XPCIE powerpc mpc85xx c29xpcie freescale - C29XPCIE:C29XPCIE,36BIT C29XPCIE_SPIFLASH powerpc mpc85xx c29xpcie freescale - C29XPCIE:C29XPCIE,36BIT,SPIFLASH -P1010RDB_36BIT_NAND powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,NAND -P1010RDB_36BIT_NAND_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,NAND_SECBOOT,SECURE_BOOT -P1010RDB_36BIT_NOR powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT -P1010RDB_36BIT_NOR_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,SECURE_BOOT -P1010RDB_36BIT_SDCARD powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,SDCARD -P1010RDB_36BIT_SPIFLASH powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,SPIFLASH -P1010RDB_36BIT_SPIFLASH_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,SPIFLASH,SECURE_BOOT -P1010RDB_NAND powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,NAND -P1010RDB_NAND_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,NAND_SECBOOT,SECURE_BOOT -P1010RDB_NOR powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB -P1010RDB_NOR_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,SECURE_BOOT -P1010RDB_SDCARD powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,SDCARD -P1010RDB_SPIFLASH powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,SPIFLASH -P1010RDB_SPIFLASH_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,SPIFLASH,SECURE_BOOT -P1011RDB powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1011RDB +P1010RDB-PA_36BIT_NAND powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PA,36BIT,NAND +P1010RDB-PA_36BIT_NAND_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PA,36BIT,NAND_SECBOOT,SECURE_BOOT +P1010RDB-PA_36BIT_NOR powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PA,36BIT +P1010RDB-PA_36BIT_NOR_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PA,36BIT,SECURE_BOOT +P1010RDB-PA_36BIT_SDCARD powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PA,36BIT,SDCARD +P1010RDB-PA_36BIT_SPIFLASH powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PA,36BIT,SPIFLASH +P1010RDB-PA_36BIT_SPIFLASH_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PA,36BIT,SPIFLASH,SECURE_BOOT +P1010RDB-PA_NAND powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PA,NAND +P1010RDB-PA_NOR powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PA +P1010RDB-PA_SDCARD powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PA,SDCARD +P1010RDB-PA_SPIFLASH powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PA,SPIFLASH +P1010RDB-PA_SPIFLASH_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PA,SPIFLASH,SECURE_BOOT +P1010RDB-PB_NOR powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB +P1010RDB-PB_NAND powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB,NAND +P1010RDB-PB_SDCARD powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB,SDCARD +P1010RDB-PB_SPIFLASH powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB,SPIFLASH +P1010RDB-PB_NOR_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB,SECURE_BOOT +P1010RDB-PB_NAND_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB,NAND_SECBOOT,SECURE_BOOT +P1010RDB-PB_SPIFLASH_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB,SPIFLASH,SECURE_BOOT +P1010RDB-PB_36BIT_NOR powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB,36BIT +P1010RDB-PB_36BIT_NOR_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB,36BIT,SECURE_BOOT +P1010RDB-PB_36BIT_NAND powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB,36BIT,NAND +P1010RDB-PB_36BIT_NAND_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB,36BIT,NAND_SECBOOT,SECURE_BOOT +P1010RDB-PB_36BIT_SDCARD powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB,36BIT,SDCARD +P1010RDB-PB_36BIT_SPIFLASH powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB,36BIT,SPIFLASH +P1010RDB-PB_36BIT_SPIFLASH_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB_PB,36BIT,SPIFLASH,SECURE_BOOT P1011RDB_36BIT powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1011RDB,36BIT P1011RDB_36BIT_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1011RDB,36BIT,SDCARD P1011RDB_36BIT_SPIFLASH powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1011RDB,36BIT,SPIFLASH diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h index ba3f7c2..8bb52af 100644 --- a/include/configs/P1010RDB.h +++ b/include/configs/P1010RDB.h @@ -120,7 +120,11 @@ #endif /* controller 2, Slot 2, tgtid 2, Base address 9000 */ +#if defined(CONFIG_P1010RDB_PA) #define CONFIG_SYS_PCIE2_NAME "PCIe Slot" +#elif defined(CONFIG_P1010RDB_PB) +#define CONFIG_SYS_PCIE2_NAME "mini PCIe Slot" +#endif #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 @@ -203,25 +207,24 @@ extern unsigned long get_sdram_size(void); #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 - #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 #define CONFIG_SYS_DDR_RCW_1 0x00000000 #define CONFIG_SYS_DDR_RCW_2 0x00000000 -#define CONFIG_SYS_DDR_CONTROL 0x470C0000 /* Type = DDR3 */ -#define CONFIG_SYS_DDR_CONTROL_2 0x04401010 +#define CONFIG_SYS_DDR_CONTROL 0xc70c0008 /* Type = DDR3 */ +#define CONFIG_SYS_DDR_CONTROL_2 0x24401000 #define CONFIG_SYS_DDR_TIMING_4 0x00000001 -#define CONFIG_SYS_DDR_TIMING_5 0x03402400 +#define CONFIG_SYS_DDR_TIMING_5 0x02401400 -#define CONFIG_SYS_DDR_TIMING_3_800 0x00020000 -#define CONFIG_SYS_DDR_TIMING_0_800 0x00330004 -#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6B4644 +#define CONFIG_SYS_DDR_TIMING_3_800 0x00030000 +#define CONFIG_SYS_DDR_TIMING_0_800 0x00110104 +#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b8644 #define CONFIG_SYS_DDR_TIMING_2_800 0x0FA888CF #define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000 -#define CONFIG_SYS_DDR_MODE_1_800 0x40461520 -#define CONFIG_SYS_DDR_MODE_2_800 0x8000c000 +#define CONFIG_SYS_DDR_MODE_1_800 0x00441420 +#define CONFIG_SYS_DDR_MODE_2_800 0x00000000 #define CONFIG_SYS_DDR_INTERVAL_800 0x0C300100 -#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8655A608 +#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8675f608 /* settings for DDR3 at 667MT/s */ #define CONFIG_SYS_DDR_TIMING_3_667 0x00010000 @@ -256,10 +259,6 @@ extern unsigned long get_sdram_size(void); * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable */ -/* In case of SD card boot, IFC interface is not available because of muxing */ -#ifdef CONFIG_SDCARD -#define CONFIG_SYS_NO_FLASH -#else /* * IFC Definitions */ @@ -322,6 +321,8 @@ extern unsigned long get_sdram_size(void); | CSPR_MSEL_NAND \ | CSPR_V) #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) + +#if defined(CONFIG_P1010RDB_PA) #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ @@ -329,13 +330,25 @@ extern unsigned long get_sdram_size(void); | CSOR_NAND_PGS_512 /* Page Size = 512b */ \ | CSOR_NAND_SPRZ_16 /* Spare size = 16 */ \ | CSOR_NAND_PB(32)) /* 32 Pages Per Block */ +#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024) +#elif defined(CONFIG_P1010RDB_PB) +#define CONFIG_SYS_NAND_ONFI_DETECTION +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ + | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ + | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ + | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \ + | CSOR_NAND_PB(128)) /*Pages Per Block = 128 */ +#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) +#endif #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_MTD_NAND_VERIFY_WRITE #define CONFIG_CMD_NAND -#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024) +#if defined(CONFIG_P1010RDB_PA) /* NAND Flash Timing Params */ #define CONFIG_SYS_NAND_FTIM0 FTIM0_NAND_TCCST(0x01) | \ FTIM0_NAND_TWP(0x0C) | \ @@ -350,6 +363,23 @@ extern unsigned long get_sdram_size(void); FTIM2_NAND_TWHRE(0x0f) #define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x04) +#elif defined(CONFIG_P1010RDB_PB) +/* support MT29F16G08ABABAWP 4k-pagesize 2G-bytes NAND */ +/* ONFI NAND Flash mode0 Timing Params */ +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07)| \ + FTIM0_NAND_TWP(0x18) | \ + FTIM0_NAND_TWCHT(0x07) | \ + FTIM0_NAND_TWH(0x0a)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32)| \ + FTIM1_NAND_TWBE(0x39) | \ + FTIM1_NAND_TRR(0x0e) | \ + FTIM1_NAND_TRP(0x18)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ + FTIM2_NAND_TREH(0x0a) | \ + FTIM2_NAND_TWHRE(0x1e)) +#define CONFIG_SYS_NAND_FTIM3 0x0 +#endif + #define CONFIG_SYS_NAND_DDR_LAW 11 /* Set up IFC registers for boot location NOR/NAND */ @@ -410,7 +440,6 @@ extern unsigned long get_sdram_size(void); FTIM2_GPCM_TCH(0x0) | \ FTIM2_GPCM_TWP(0x1f)) #define CONFIG_SYS_CS3_FTIM3 0x0 -#endif /* CONFIG_SDCARD */ #if defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH) #define CONFIG_SYS_RAMBOOT @@ -482,9 +511,20 @@ extern unsigned long get_sdram_size(void); #define CONFIG_SYS_FSL_I2C2_SPEED 400000 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define I2C_PCA9557_ADDR1 0x18 +#define I2C_PCA9557_ADDR2 0x19 +#define I2C_PCA9557_BUS_NUM 0 /* I2C EEPROM */ -#undef CONFIG_ID_EEPROM +#if defined(CONFIG_P1010RDB_PB) +#define CONFIG_ID_EEPROM +#ifdef CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#endif +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#endif /* enable read and write access to EEPROM */ #define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_MULTI_EEPROMS @@ -567,12 +607,7 @@ extern unsigned long get_sdram_size(void); #define CONFIG_LBA48 #endif /* #ifdef CONFIG_FSL_SATA */ -/* SD interface will only be available in case of SD boot */ -#ifdef CONFIG_SDCARD #define CONFIG_MMC -#define CONFIG_DEF_HWCONFIG esdhc -#endif - #ifdef CONFIG_MMC #define CONFIG_CMD_MMC #define CONFIG_DOS_PARTITION @@ -613,9 +648,14 @@ extern unsigned long get_sdram_size(void); #define CONFIG_ENV_SIZE 0x2000 #elif defined(CONFIG_NAND) #define CONFIG_ENV_IS_IN_NAND +#if defined(CONFIG_P1010RDB_PA) #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) /* 3*16=48K for env */ +#elif defined(CONFIG_P1010RDB_PB) +#define CONFIG_ENV_SIZE (16 * 1024) +#define CONFIG_ENV_RANGE (32 * CONFIG_ENV_SIZE) /* new block size 512K */ +#endif #define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) -#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) #elif defined(CONFIG_SYS_RAMBOOT) #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) @@ -708,7 +748,6 @@ extern unsigned long get_sdram_size(void); #define CONFIG_HAS_ETH2 #endif -#define CONFIG_HOSTNAME P1010RDB #define CONFIG_ROOTPATH "/opt/nfsroot" #define CONFIG_BOOTFILE "uImage" #define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */ @@ -747,7 +786,31 @@ extern unsigned long get_sdram_size(void); "ext2load usb 0:4 $loadaddr $bootfile;" \ "ext2load usb 0:4 $fdtaddr $fdtfile;" \ "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ + CONFIG_BOOTMODE + +#if defined(CONFIG_P1010RDB_PA) +#define CONFIG_BOOTMODE \ + "boot_bank0=i2c dev 0; i2c mw 18 1 f1; i2c mw 18 3 f0;" \ + "mw.b ffb00011 0; mw.b ffb00009 0; reset\0" \ + "boot_bank1=i2c dev 0; i2c mw 18 1 f1; i2c mw 18 3 f0;" \ + "mw.b ffb00011 0; mw.b ffb00009 1; reset\0" \ + "boot_nand=i2c dev 0; i2c mw 18 1 f9; i2c mw 18 3 f0;" \ + "mw.b ffb00011 0; mw.b ffb00017 1; reset\0" + +#elif defined(CONFIG_P1010RDB_PB) +#define CONFIG_BOOTMODE \ + "boot_bank0=i2c dev 0; i2c mw 18 1 fe; i2c mw 18 3 0;" \ + "i2c mw 19 1 2; i2c mw 19 3 e1; reset\0" \ + "boot_bank1=i2c dev 0; i2c mw 18 1 fe; i2c mw 18 3 0;" \ + "i2c mw 19 1 12; i2c mw 19 3 e1; reset\0" \ + "boot_nand=i2c dev 0; i2c mw 18 1 fc; i2c mw 18 3 0;" \ + "i2c mw 19 1 8; i2c mw 19 3 f7; reset\0" \ + "boot_spi=i2c dev 0; i2c mw 18 1 fa; i2c mw 18 3 0;" \ + "i2c mw 19 1 0; i2c mw 19 3 f7; reset\0" \ + "boot_sd=i2c dev 0; i2c mw 18 1 f8; i2c mw 18 3 0;" \ + "i2c mw 19 1 4; i2c mw 19 3 f3; reset\0" +#endif #define CONFIG_RAMBOOTCOMMAND \ "setenv bootargs root=/dev/ram rw " \ -- 1.8.0

1 0

[U-Boot] [PATCH v3] i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework
by Heiko Schocher 02 Sep '13

02 Sep '13

- add omap24xx driver to new multibus/multiadpater support - adapted all config files, which uses this driver Tested on the am335x based siemens boards rut, dxr2 and pxm2 posted here: http://patchwork.ozlabs.org/patch/263211/ Signed-off-by: Heiko Schocher <hs(a)denx.de> Cc: Tom Rini <trini(a)ti.com> Cc: Lars Poeschel <poeschel(a)lemonage.de> Cc: Steve Sakoman <sakoman(a)gmail.com> Cc: Thomas Weber <weber(a)corscience.de> Cc: Tom Rix <Tom.Rix(a)windriver.com> Cc: Grazvydas Ignotas <notasas(a)gmail.com> Cc: Enric Balletbo i Serra <eballetbo(a)iseebcn.com> Cc: Luca Ceresoli <luca.ceresoli(a)comelit.it> Cc: Igor Grinberg <grinberg(a)compulab.co.il> Cc: Ilya Yanok <yanok(a)emcraft.com> Cc: Stefano Babic <sbabic(a)denx.de> Cc: Nishanth Menon <nm(a)ti.com> Cc: Pali Rohár <pali.rohar(a)gmail.com> Cc: Peter Barada <peter.barada(a)logicpd.com> Cc: Nagendra T S <nagendra(a)mistralsolutions.com> Cc: Michael Jones <michael.jones(a)matrix-vision.de> Cc: Raphael Assenat <raph(a)8d.com> --- - changes for v2: rebased against u-boot-ti 425faf74cd8189c87919f7e72a0101c684ee3b9f - changes for v3: rebase against: u-boot-it 901ce27c6f018992b7dd6c08d3c98cf217cc4c96 add siemens boards (rut, dxr2 and pxm2) --- README | 13 ++ arch/arm/cpu/armv7/omap-common/clocks-common.c | 3 +- arch/arm/cpu/armv7/omap3/board.c | 2 +- arch/arm/cpu/armv7/omap3/clock.c | 2 +- arch/arm/include/asm/arch-am33xx/i2c.h | 6 +- board/compulab/cm_t35/Makefile | 2 +- board/compulab/cm_t35/cm_t35.c | 2 +- board/compulab/cm_t35/eeprom.h | 2 +- board/logicpd/am3517evm/am3517evm.c | 4 +- board/overo/overo.c | 2 +- board/phytec/pcm051/board.c | 4 +- board/siemens/common/board.c | 4 +- board/ti/am335x/board.c | 2 +- board/ti/am3517crane/am3517crane.c | 4 +- board/ti/evm/evm.c | 4 +- drivers/i2c/Makefile | 4 +- drivers/i2c/omap24xx_i2c.c | 172 ++++++++++++++++--------- include/configs/am335x_evm.h | 1 - include/configs/am3517_crane.h | 8 +- include/configs/am3517_evm.h | 8 +- include/configs/cm_t35.h | 8 +- include/configs/devkit8000.h | 8 +- include/configs/dig297.h | 8 +- include/configs/igep00x0.h | 8 +- include/configs/mcx.h | 8 +- include/configs/nokia_rx51.h | 8 +- include/configs/omap3_beagle.h | 9 +- include/configs/omap3_evm_common.h | 9 +- include/configs/omap3_logic.h | 10 +- include/configs/omap3_mvblx.h | 9 +- include/configs/omap3_overo.h | 9 +- include/configs/omap3_pandora.h | 8 +- include/configs/omap3_sdp3430.h | 8 +- include/configs/omap3_zoom1.h | 8 +- include/configs/omap3_zoom2.h | 8 +- include/configs/omap4_common.h | 9 +- include/configs/pcm051.h | 9 +- include/configs/siemens-am33x-common.h | 9 +- include/configs/tam3517-common.h | 11 +- include/configs/ti_armv7_common.h | 9 +- include/configs/tricorder.h | 8 +- 41 Dateien geändert, 238 Zeilen hinzugefügt(+), 192 Zeilen entfernt(-) diff --git a/README b/README index 78aa5a5..a30ea31 100644 --- a/README +++ b/README @@ -1974,6 +1974,19 @@ CBFS (Coreboot Filesystem) support - CONFIG_SYS_I2C_PPC4XX_CH0 activate hardware channel 0 - CONFIG_SYS_I2C_PPC4XX_CH1 activate hardware channel 1 + - drivers/i2c/omap24xx_i2c.c + - activate this driver with CONFIG_SYS_I2C_OMAP24XX + - CONFIG_SYS_OMAP24_I2C_SPEED speed channel 0 + - CONFIG_SYS_OMAP24_I2C_SLAVE slave addr channel 0 + - CONFIG_SYS_OMAP24_I2C_SPEED1 speed channel 1 + - CONFIG_SYS_OMAP24_I2C_SLAVE1 slave addr channel 1 + - CONFIG_SYS_OMAP24_I2C_SPEED2 speed channel 2 + - CONFIG_SYS_OMAP24_I2C_SLAVE2 slave addr channel 2 + - CONFIG_SYS_OMAP24_I2C_SPEED3 speed channel 3 + - CONFIG_SYS_OMAP24_I2C_SLAVE3 slave addr channel 3 + - CONFIG_SYS_OMAP24_I2C_SPEED4 speed channel 4 + - CONFIG_SYS_OMAP24_I2C_SLAVE4 slave addr channel 4 + additional defines: CONFIG_SYS_NUM_I2C_BUSES diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c index 7580594..fc70595 100644 --- a/arch/arm/cpu/armv7/omap-common/clocks-common.c +++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c @@ -786,7 +786,8 @@ void gpi2c_init(void) static int gpi2c = 1; if (gpi2c) { - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, + CONFIG_SYS_OMAP24_I2C_SLAVE); gpi2c = 0; } } diff --git a/arch/arm/cpu/armv7/omap3/board.c b/arch/arm/cpu/armv7/omap3/board.c index 7d1f8d9..2922816 100644 --- a/arch/arm/cpu/armv7/omap3/board.c +++ b/arch/arm/cpu/armv7/omap3/board.c @@ -98,7 +98,7 @@ void spl_board_init(void) gpmc_init(); #endif #ifdef CONFIG_SPL_I2C_SUPPORT - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); #endif } #endif /* CONFIG_SPL_BUILD */ diff --git a/arch/arm/cpu/armv7/omap3/clock.c b/arch/arm/cpu/armv7/omap3/clock.c index 9f989ff..14fc7e8 100644 --- a/arch/arm/cpu/armv7/omap3/clock.c +++ b/arch/arm/cpu/armv7/omap3/clock.c @@ -708,7 +708,7 @@ void per_clocks_enable(void) sr32(&prcm_base->iclken_per, 17, 1, 1); #endif -#ifdef CONFIG_DRIVER_OMAP34XX_I2C +#ifdef CONFIG_SYS_I2C_OMAP34XX /* Turn on all 3 I2C clocks */ sr32(&prcm_base->fclken1_core, 15, 3, 0x7); sr32(&prcm_base->iclken1_core, 15, 3, 0x7); /* I2C1,2,3 = on */ diff --git a/arch/arm/include/asm/arch-am33xx/i2c.h b/arch/arm/include/asm/arch-am33xx/i2c.h index 8bfa53f..8642c8f 100644 --- a/arch/arm/include/asm/arch-am33xx/i2c.h +++ b/arch/arm/include/asm/arch-am33xx/i2c.h @@ -4,8 +4,8 @@ * * SPDX-License-Identifier: GPL-2.0+ */ -#ifndef _I2C_H_ -#define _I2C_H_ +#ifndef _I2C_AM33XX_H_ +#define _I2C_AM33XX_H_ #define I2C_BASE1 0x44E0B000 #define I2C_BASE2 0x4802A000 @@ -62,4 +62,4 @@ struct i2c { #define I2C_IP_CLK 48000000 #define I2C_INTERNAL_SAMPLING_CLK 12000000 -#endif /* _I2C_H_ */ +#endif /* _I2C_AM33XX_H_ */ diff --git a/board/compulab/cm_t35/Makefile b/board/compulab/cm_t35/Makefile index 6d07947..9014d2a 100644 --- a/board/compulab/cm_t35/Makefile +++ b/board/compulab/cm_t35/Makefile @@ -11,7 +11,7 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o -COBJS-$(CONFIG_DRIVER_OMAP34XX_I2C) += eeprom.o +COBJS-$(CONFIG_SYS_I2C_OMAP34XX) += eeprom.o COBJS-$(CONFIG_LCD) += display.o COBJS := cm_t35.o leds.o $(COBJS-y) diff --git a/board/compulab/cm_t35/cm_t35.c b/board/compulab/cm_t35/cm_t35.c index 3caa5be..1dd3647 100644 --- a/board/compulab/cm_t35/cm_t35.c +++ b/board/compulab/cm_t35/cm_t35.c @@ -470,7 +470,7 @@ static void setup_net_chip_gmpc(void) &ctrl_base->gpmc_nadv_ale); } -#ifdef CONFIG_DRIVER_OMAP34XX_I2C +#ifdef CONFIG_SYS_I2C_OMAP34XX /* * Routine: reset_net_chip * Description: reset the Ethernet controller via TPS65930 GPIO diff --git a/board/compulab/cm_t35/eeprom.h b/board/compulab/cm_t35/eeprom.h index 02ffbb1..a07559d 100644 --- a/board/compulab/cm_t35/eeprom.h +++ b/board/compulab/cm_t35/eeprom.h @@ -10,7 +10,7 @@ #ifndef _EEPROM_ #define _EEPROM_ -#ifdef CONFIG_DRIVER_OMAP34XX_I2C +#ifdef CONFIG_SYS_I2C_OMAP34XX int cm_t3x_eeprom_read_mac_addr(uchar *buf); u32 cm_t3x_eeprom_get_board_rev(void); #else diff --git a/board/logicpd/am3517evm/am3517evm.c b/board/logicpd/am3517evm/am3517evm.c index 1cabc80..33709bd 100644 --- a/board/logicpd/am3517evm/am3517evm.c +++ b/board/logicpd/am3517evm/am3517evm.c @@ -98,8 +98,8 @@ static void am3517_evm_musb_init(void) */ int misc_init_r(void) { -#ifdef CONFIG_DRIVER_OMAP34XX_I2C - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +#ifdef CONFIG_SYS_I2C_OMAP34XX + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); #endif dieid_num_r(); diff --git a/board/overo/overo.c b/board/overo/overo.c index aace42a..9ac35d2 100644 --- a/board/overo/overo.c +++ b/board/overo/overo.c @@ -92,7 +92,7 @@ int get_board_revision(void) { int revision; -#ifdef CONFIG_DRIVER_OMAP34XX_I2C +#ifdef CONFIG_SYS_I2C_OMAP34XX unsigned char data; /* board revisions <= R2410 connect 4030 irq_1 to gpio112 */ diff --git a/board/phytec/pcm051/board.c b/board/phytec/pcm051/board.c index e40b0bd..a2ad650 100644 --- a/board/phytec/pcm051/board.c +++ b/board/phytec/pcm051/board.c @@ -91,7 +91,7 @@ void set_mux_conf_regs(void) { /* Initalize the board header */ enable_i2c0_pin_mux(); - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); enable_board_pin_mux(); } @@ -108,7 +108,7 @@ void sdram_init(void) */ int board_init(void) { - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; diff --git a/board/siemens/common/board.c b/board/siemens/common/board.c index 6279c32..32d2ee4 100644 --- a/board/siemens/common/board.c +++ b/board/siemens/common/board.c @@ -42,7 +42,7 @@ void set_mux_conf_regs(void) { /* Initalize the board header */ enable_i2c0_pin_mux(); - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); if (read_eeprom() < 0) puts("Could not get board ID.\n"); @@ -67,7 +67,7 @@ int board_init(void) #if defined(CONFIG_HW_WATCHDOG) hw_watchdog_init(); #endif /* defined(CONFIG_HW_WATCHDOG) */ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); if (read_eeprom() < 0) puts("Could not get board ID.\n"); diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c index cc04426..f78af9a 100644 --- a/board/ti/am335x/board.c +++ b/board/ti/am335x/board.c @@ -249,7 +249,7 @@ const struct dpll_params *get_dpll_ddr_params(void) struct am335x_baseboard_id header; enable_i2c0_pin_mux(); - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); if (read_eeprom(&header) < 0) puts("Could not get board ID.\n"); diff --git a/board/ti/am3517crane/am3517crane.c b/board/ti/am3517crane/am3517crane.c index 5eb97ff..a649697 100644 --- a/board/ti/am3517crane/am3517crane.c +++ b/board/ti/am3517crane/am3517crane.c @@ -43,8 +43,8 @@ int board_init(void) */ int misc_init_r(void) { -#ifdef CONFIG_DRIVER_OMAP34XX_I2C - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +#ifdef CONFIG_SYS_I2C_OMAP34XX + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); #endif dieid_num_r(); diff --git a/board/ti/evm/evm.c b/board/ti/evm/evm.c index c71c218..81dd081 100644 --- a/board/ti/evm/evm.c +++ b/board/ti/evm/evm.c @@ -146,8 +146,8 @@ void get_board_mem_timings(struct board_sdrc_timings *timings) int misc_init_r(void) { -#ifdef CONFIG_DRIVER_OMAP34XX_I2C - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +#ifdef CONFIG_SYS_I2C_OMAP34XX + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); #endif #if defined(CONFIG_CMD_NET) diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile index 37ccbd1..f32daea 100644 --- a/drivers/i2c/Makefile +++ b/drivers/i2c/Makefile @@ -17,8 +17,6 @@ COBJS-$(CONFIG_I2C_MV) += mv_i2c.o COBJS-$(CONFIG_I2C_MXC) += mxc_i2c.o COBJS-$(CONFIG_I2C_MXS) += mxs_i2c.o COBJS-$(CONFIG_DRIVER_OMAP1510_I2C) += omap1510_i2c.o -COBJS-$(CONFIG_DRIVER_OMAP24XX_I2C) += omap24xx_i2c.o -COBJS-$(CONFIG_DRIVER_OMAP34XX_I2C) += omap24xx_i2c.o COBJS-$(CONFIG_PCA9564_I2C) += pca9564_i2c.o COBJS-$(CONFIG_DRIVER_S3C24X0_I2C) += s3c24x0_i2c.o COBJS-$(CONFIG_S3C44B0_I2C) += s3c44b0_i2c.o @@ -30,6 +28,8 @@ COBJS-$(CONFIG_SYS_I2C) += i2c_core.o COBJS-$(CONFIG_SYS_I2C_FSL) += fsl_i2c.o COBJS-$(CONFIG_SYS_I2C_FTI2C010) += fti2c010.o COBJS-$(CONFIG_SYS_I2C_PPC4XX) += ppc4xx_i2c.o +COBJS-$(CONFIG_SYS_I2C_OMAP24XX) += omap24xx_i2c.o +COBJS-$(CONFIG_SYS_I2C_OMAP34XX) += omap24xx_i2c.o COBJS-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o COBJS-$(CONFIG_SYS_I2C_TEGRA) += tegra_i2c.o COBJS-$(CONFIG_ZYNQ_I2C) += zynq_i2c.o diff --git a/drivers/i2c/omap24xx_i2c.c b/drivers/i2c/omap24xx_i2c.c index ef38d71..3d38c03 100644 --- a/drivers/i2c/omap24xx_i2c.c +++ b/drivers/i2c/omap24xx_i2c.c @@ -35,6 +35,7 @@ */ #include <common.h> +#include <i2c.h> #include <asm/arch/i2c.h> #include <asm/io.h> @@ -48,22 +49,14 @@ DECLARE_GLOBAL_DATA_PTR; /* Absolutely safe for status update at 100 kHz I2C: */ #define I2C_WAIT 200 -static int wait_for_bb(void); -static u16 wait_for_event(void); -static void flush_fifo(void); +static int wait_for_bb(struct i2c_adapter *adap); +static struct i2c *omap24_get_base(struct i2c_adapter *adap); +static u16 wait_for_event(struct i2c_adapter *adap); +static void flush_fifo(struct i2c_adapter *adap); -/* - * For SPL boot some boards need i2c before SDRAM is initialised so force - * variables to live in SRAM - */ -static struct i2c __attribute__((section (".data"))) *i2c_base = - (struct i2c *)I2C_DEFAULT_BASE; -static unsigned int __attribute__((section (".data"))) bus_initialized[I2C_BUS_MAX] = - { [0 ... (I2C_BUS_MAX-1)] = 0 }; -static unsigned int __attribute__((section (".data"))) current_bus = 0; - -void i2c_init(int speed, int slaveadd) +static void omap24_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd) { + struct i2c *i2c_base = omap24_get_base(adap); int psc, fsscll, fssclh; int hsscll = 0, hssclh = 0; u32 scll, sclh; @@ -163,16 +156,15 @@ void i2c_init(int speed, int slaveadd) I2C_IE_NACK_IE | I2C_IE_AL_IE, &i2c_base->ie); #endif udelay(1000); - flush_fifo(); + flush_fifo(adap); writew(0xFFFF, &i2c_base->stat); writew(0, &i2c_base->cnt); - - if (gd->flags & GD_FLG_RELOC) - bus_initialized[current_bus] = 1; } -static void flush_fifo(void) -{ u16 stat; +static void flush_fifo(struct i2c_adapter *adap) +{ + struct i2c *i2c_base = omap24_get_base(adap); + u16 stat; /* note: if you try and read data when its not there or ready * you get a bus error @@ -192,8 +184,9 @@ static void flush_fifo(void) * i2c_probe: Use write access. Allows to identify addresses that are * write-only (like the config register of dual-port EEPROMs) */ -int i2c_probe(uchar chip) +static int omap24_i2c_probe(struct i2c_adapter *adap, uchar chip) { + struct i2c *i2c_base = omap24_get_base(adap); u16 status; int res = 1; /* default = fail */ @@ -201,7 +194,7 @@ int i2c_probe(uchar chip) return res; /* Wait until bus is free */ - if (wait_for_bb()) + if (wait_for_bb(adap)) return res; /* No data transfer, slave addr only */ @@ -212,7 +205,7 @@ int i2c_probe(uchar chip) writew(I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX | I2C_CON_STP, &i2c_base->con); - status = wait_for_event(); + status = wait_for_event(adap); if ((status & ~I2C_STAT_XRDY) == 0 || (status & I2C_STAT_AL)) { /* @@ -223,7 +216,7 @@ int i2c_probe(uchar chip) */ if (status == I2C_STAT_XRDY) printf("i2c_probe: pads on bus %d probably not configured (status=0x%x)\n", - current_bus, status); + adap->hwadapnr, status); goto pr_exit; } @@ -239,7 +232,7 @@ int i2c_probe(uchar chip) I2C_CON_STP, &i2c_base->con); /* STP */ } pr_exit: - flush_fifo(); + flush_fifo(adap); writew(0xFFFF, &i2c_base->stat); writew(0, &i2c_base->cnt); return res; @@ -258,8 +251,10 @@ pr_exit: * or that do not need a register address at all (such as some clock * distributors). */ -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) +static int omap24_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { + struct i2c *i2c_base = omap24_get_base(adap); int i2c_error = 0; u16 status; @@ -287,7 +282,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) } /* Wait until bus not busy */ - if (wait_for_bb()) + if (wait_for_bb(adap)) return 1; /* Zero, one or two bytes reg address (offset) */ @@ -308,12 +303,12 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) #endif /* Send register offset */ while (1) { - status = wait_for_event(); + status = wait_for_event(adap); /* Try to identify bus that is not padconf'd for I2C */ if (status == I2C_STAT_XRDY) { i2c_error = 2; printf("i2c_read (addr phase): pads on bus %d probably not configured (status=0x%x)\n", - current_bus, status); + adap->hwadapnr, status); goto rd_exit; } if (status == 0 || status & I2C_STAT_NACK) { @@ -348,7 +343,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) /* Receive data */ while (1) { - status = wait_for_event(); + status = wait_for_event(adap); /* * Try to identify bus that is not padconf'd for I2C. This * state could be left over from previous transactions if @@ -357,7 +352,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) if (status == I2C_STAT_XRDY) { i2c_error = 2; printf("i2c_read (data phase): pads on bus %d probably not configured (status=0x%x)\n", - current_bus, status); + adap->hwadapnr, status); goto rd_exit; } if (status == 0 || status & I2C_STAT_NACK) { @@ -375,15 +370,17 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) } rd_exit: - flush_fifo(); + flush_fifo(adap); writew(0xFFFF, &i2c_base->stat); writew(0, &i2c_base->cnt); return i2c_error; } /* i2c_write: Address (reg offset) may be 0, 1 or 2 bytes long. */ -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) +static int omap24_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { + struct i2c *i2c_base = omap24_get_base(adap); int i; u16 status; int i2c_error = 0; @@ -415,7 +412,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) } /* Wait until bus not busy */ - if (wait_for_bb()) + if (wait_for_bb(adap)) return 1; /* Start address phase - will write regoffset + len bytes data */ @@ -428,12 +425,12 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) while (alen) { /* Must write reg offset (one or two bytes) */ - status = wait_for_event(); + status = wait_for_event(adap); /* Try to identify bus that is not padconf'd for I2C */ if (status == I2C_STAT_XRDY) { i2c_error = 2; printf("i2c_write: pads on bus %d probably not configured (status=0x%x)\n", - current_bus, status); + adap->hwadapnr, status); goto wr_exit; } if (status == 0 || status & I2C_STAT_NACK) { @@ -455,7 +452,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) } /* Address phase is over, now write data */ for (i = 0; i < len; i++) { - status = wait_for_event(); + status = wait_for_event(adap); if (status == 0 || status & I2C_STAT_NACK) { i2c_error = 1; printf("i2c_write: error waiting for data ACK (status=0x%x)\n", @@ -474,7 +471,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) } wr_exit: - flush_fifo(); + flush_fifo(adap); writew(0xFFFF, &i2c_base->stat); writew(0, &i2c_base->cnt); return i2c_error; @@ -484,8 +481,9 @@ wr_exit: * Wait for the bus to be free by checking the Bus Busy (BB) * bit to become clear */ -static int wait_for_bb(void) +static int wait_for_bb(struct i2c_adapter *adap) { + struct i2c *i2c_base = omap24_get_base(adap); int timeout = I2C_TIMEOUT; u16 stat; @@ -514,8 +512,9 @@ static int wait_for_bb(void) * Wait for the I2C controller to complete current action * and update status */ -static u16 wait_for_event(void) +static u16 wait_for_event(struct i2c_adapter *adap) { + struct i2c *i2c_base = omap24_get_base(adap); u16 status; int timeout = I2C_TIMEOUT; @@ -540,7 +539,7 @@ static u16 wait_for_event(void) * not been configured for I2C, and/or pull-ups are missing. */ printf("Check if pads/pull-ups of bus %d are properly configured\n", - current_bus); + adap->hwadapnr); writew(0xFFFF, &i2c_base->stat); status = 0; } @@ -548,48 +547,93 @@ static u16 wait_for_event(void) return status; } -int i2c_set_bus_num(unsigned int bus) +static struct i2c *omap24_get_base(struct i2c_adapter *adap) { - if (bus >= I2C_BUS_MAX) { - printf("Bad bus: %x\n", bus); - return -1; - } - - switch (bus) { - default: - bus = 0; /* Fall through */ + switch (adap->hwadapnr) { case 0: - i2c_base = (struct i2c *)I2C_BASE1; + return (struct i2c *)I2C_BASE1; break; case 1: - i2c_base = (struct i2c *)I2C_BASE2; + return (struct i2c *)I2C_BASE2; break; #if (I2C_BUS_MAX > 2) case 2: - i2c_base = (struct i2c *)I2C_BASE3; + return (struct i2c *)I2C_BASE3; break; #if (I2C_BUS_MAX > 3) case 3: - i2c_base = (struct i2c *)I2C_BASE4; + return (struct i2c *)I2C_BASE4; break; #if (I2C_BUS_MAX > 4) case 4: - i2c_base = (struct i2c *)I2C_BASE5; + return (struct i2c *)I2C_BASE5; break; #endif #endif #endif + default: + printf("wrong hwadapnr: %d\n", adap->hwadapnr); + break; } + return NULL; +} - current_bus = bus; +#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED1) +#define CONFIG_SYS_OMAP24_I2C_SPEED1 CONFIG_SYS_OMAP24_I2C_SPEED +#endif +#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE1) +#define CONFIG_SYS_OMAP24_I2C_SLAVE1 CONFIG_SYS_OMAP24_I2C_SLAVE +#endif - if (!bus_initialized[current_bus]) - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +U_BOOT_I2C_ADAP_COMPLETE(omap24_0, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED, + CONFIG_SYS_OMAP24_I2C_SLAVE, + 0) +U_BOOT_I2C_ADAP_COMPLETE(omap24_1, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED1, + CONFIG_SYS_OMAP24_I2C_SLAVE1, + 1) +#if (I2C_BUS_MAX > 2) +#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED2) +#define CONFIG_SYS_OMAP24_I2C_SPEED2 CONFIG_SYS_OMAP24_I2C_SPEED +#endif +#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE2) +#define CONFIG_SYS_OMAP24_I2C_SLAVE2 CONFIG_SYS_OMAP24_I2C_SLAVE +#endif - return 0; -} +U_BOOT_I2C_ADAP_COMPLETE(omap24_2, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED2, + CONFIG_SYS_OMAP24_I2C_SLAVE2, + 2) +#if (I2C_BUS_MAX > 3) +#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED3) +#define CONFIG_SYS_OMAP24_I2C_SPEED3 CONFIG_SYS_OMAP24_I2C_SPEED +#endif +#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE3) +#define CONFIG_SYS_OMAP24_I2C_SLAVE3 CONFIG_SYS_OMAP24_I2C_SLAVE +#endif -int i2c_get_bus_num(void) -{ - return (int) current_bus; -} +U_BOOT_I2C_ADAP_COMPLETE(omap24_3, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED3, + CONFIG_SYS_OMAP24_I2C_SLAVE3, + 3) +#if (I2C_BUS_MAX > 4) +#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED4) +#define CONFIG_SYS_OMAP24_I2C_SPEED4 CONFIG_SYS_OMAP24_I2C_SPEED +#endif +#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE4) +#define CONFIG_SYS_OMAP24_I2C_SLAVE4 CONFIG_SYS_OMAP24_I2C_SLAVE +#endif + +U_BOOT_I2C_ADAP_COMPLETE(omap24_4, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED4, + CONFIG_SYS_OMAP24_I2C_SLAVE4, + 4) +#endif +#endif +#endif diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index eae5a19..b2c8ea8 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -180,7 +180,6 @@ #define CONFIG_SYS_NS16550_COM6 0x481aa000 /* UART5 */ #define CONFIG_BAUDRATE 115200 -/* I2C Configuration */ #define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */ diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h index 1fd2508..73207f9 100644 --- a/include/configs/am3517_crane.h +++ b/include/configs/am3517_crane.h @@ -142,10 +142,10 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX #undef CONFIG_CMD_NET #undef CONFIG_CMD_NFS diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h index 6500878..fa44597 100644 --- a/include/configs/am3517_evm.h +++ b/include/configs/am3517_evm.h @@ -136,10 +136,10 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX #undef CONFIG_CMD_NET #undef CONFIG_CMD_NFS diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h index bc5b66c..c301697 100644 --- a/include/configs/cm_t35.h +++ b/include/configs/cm_t35.h @@ -140,10 +140,10 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 #define CONFIG_I2C_MULTI_BUS diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h index cb79b4e..670945a 100644 --- a/include/configs/devkit8000.h +++ b/include/configs/devkit8000.h @@ -90,10 +90,10 @@ #define CONFIG_DOS_PARTITION 1 /* I2C */ -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* TWL4030 */ #define CONFIG_TWL4030_POWER 1 diff --git a/include/configs/dig297.h b/include/configs/dig297.h index 30e3908..e066f7b 100644 --- a/include/configs/dig297.h +++ b/include/configs/dig297.h @@ -123,10 +123,10 @@ #undef CONFIG_CMD_NFS /* NFS support */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/igep00x0.h b/include/configs/igep00x0.h index 9982cf6..e1a92f0 100644 --- a/include/configs/igep00x0.h +++ b/include/configs/igep00x0.h @@ -124,10 +124,10 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/mcx.h b/include/configs/mcx.h index 85ae016..5a2a693 100644 --- a/include/configs/mcx.h +++ b/include/configs/mcx.h @@ -137,10 +137,10 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* RTC */ #define CONFIG_RTC_DS1337 diff --git a/include/configs/nokia_rx51.h b/include/configs/nokia_rx51.h index cfc5f12..40a77ff 100644 --- a/include/configs/nokia_rx51.h +++ b/include/configs/nokia_rx51.h @@ -157,10 +157,10 @@ #undef CONFIG_CMD_SETGETDCR /* DCR support on 4xx */ #define CONFIG_OMAP3_SPI -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index c1245e7..aa8de324e 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -161,11 +161,10 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_I2C_MULTI_BUS 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX #define CONFIG_VIDEO_OMAP3 /* DSS Support */ /* diff --git a/include/configs/omap3_evm_common.h b/include/configs/omap3_evm_common.h index edf6543..bc7d24e 100644 --- a/include/configs/omap3_evm_common.h +++ b/include/configs/omap3_evm_common.h @@ -88,11 +88,10 @@ /* * I2C */ -#define CONFIG_HARD_I2C -#define CONFIG_DRIVER_OMAP34XX_I2C - -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * PISMO support diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h index ee6db51..b49c5a1 100644 --- a/include/configs/omap3_logic.h +++ b/include/configs/omap3_logic.h @@ -118,12 +118,10 @@ /* * I2C */ -#define CONFIG_HARD_I2C -#define CONFIG_DRIVER_OMAP34XX_I2C - -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/omap3_mvblx.h b/include/configs/omap3_mvblx.h index 0c88419..6eaeeae 100644 --- a/include/configs/omap3_mvblx.h +++ b/include/configs/omap3_mvblx.h @@ -128,11 +128,10 @@ #define CONFIG_CMD_PING #define CONFIG_CMD_FPGA -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 -#define CONFIG_I2C_MULTI_BUS 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h index 88380a4..8344028 100644 --- a/include/configs/omap3_overo.h +++ b/include/configs/omap3_overo.h @@ -98,11 +98,10 @@ #define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_DRIVER_OMAP34XX_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h index 91a2568..4f36d07 100644 --- a/include/configs/omap3_pandora.h +++ b/include/configs/omap3_pandora.h @@ -111,10 +111,10 @@ #undef CONFIG_CMD_NFS /* NFS support */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/omap3_sdp3430.h b/include/configs/omap3_sdp3430.h index a5e469c..57929d7 100644 --- a/include/configs/omap3_sdp3430.h +++ b/include/configs/omap3_sdp3430.h @@ -114,10 +114,10 @@ /* * I2C for power management setup */ -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* OMITTED: single 1 Gbit MT29F1G NAND flash */ diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h index c747d52..fdc4ab9 100644 --- a/include/configs/omap3_zoom1.h +++ b/include/configs/omap3_zoom1.h @@ -118,10 +118,10 @@ #undef CONFIG_CMD_NFS /* NFS support */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h index cb8c7ec..f749740 100644 --- a/include/configs/omap3_zoom2.h +++ b/include/configs/omap3_zoom2.h @@ -138,10 +138,10 @@ #undef CONFIG_CMD_NFS /* NFS support */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/omap4_common.h b/include/configs/omap4_common.h index e9f2383..97d5a6b 100644 --- a/include/configs/omap4_common.h +++ b/include/configs/omap4_common.h @@ -73,11 +73,10 @@ #define CONFIG_ARCH_CPU_INIT /* I2C */ -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 -#define CONFIG_I2C_MULTI_BUS 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* TWL6030 */ #ifndef CONFIG_SPL_BUILD diff --git a/include/configs/pcm051.h b/include/configs/pcm051.h index d4d4d79..a5c3f6b 100644 --- a/include/configs/pcm051.h +++ b/include/configs/pcm051.h @@ -173,11 +173,10 @@ /* I2C Configuration */ #define CONFIG_I2C #define CONFIG_CMD_I2C -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_DRIVER_OMAP24XX_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP24XX #define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */ diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h index 6593425..0438d9c 100644 --- a/include/configs/siemens-am33x-common.h +++ b/include/configs/siemens-am33x-common.h @@ -133,11 +133,10 @@ /* I2C Configuration */ #define CONFIG_I2C #define CONFIG_CMD_I2C -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_DRIVER_OMAP24XX_I2C - +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED OMAP_I2C_STANDARD +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP24XX /* Defines for SPL */ #define CONFIG_SPL diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h index c215f0b..e47b4f7 100644 --- a/include/configs/tam3517-common.h +++ b/include/configs/tam3517-common.h @@ -117,14 +117,13 @@ #undef CONFIG_CMD_IMLS #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_SLAVE 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 400000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CONFIG_DRIVER_OMAP34XX_I2C - /* * Board NAND Info. @@ -371,7 +370,7 @@ struct tam3517_module_info { #define TAM3517_READ_EEPROM(info, ret) \ do { \ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); \ + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \ if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, \ (void *)info, sizeof(*info))) \ ret = 1; \ diff --git a/include/configs/ti_armv7_common.h b/include/configs/ti_armv7_common.h index e89e874..72a4ec5 100644 --- a/include/configs/ti_armv7_common.h +++ b/include/configs/ti_armv7_common.h @@ -60,12 +60,11 @@ /* I2C IP block */ #define CONFIG_I2C -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_DRIVER_OMAP24XX_I2C #define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP24XX /* MMC/SD IP block */ #define CONFIG_MMC diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h index a9b2714..8ceb93a 100644 --- a/include/configs/tricorder.h +++ b/include/configs/tricorder.h @@ -80,10 +80,10 @@ #define CONFIG_DOS_PARTITION /* I2C */ -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* TWL4030 */ #define CONFIG_TWL4030_POWER -- 1.7.11.7

2 2