November 2012 - U-Boot

[U-Boot] [PATCH] common/cmd_ext_common: measure throughput
by Andreas Bießmann 14 Nov '12

14 Nov '12

This patch adds time measurement and throughput calculation for the ext2load and ext4load commands. The output of ext2load changes from ---8<--- Loading file "/boot/uImage" from mmc device 0:1 1830666 bytes read --->8--- to ---8<--- Loading file "/boot/uImage" from mmc device 0:1 1830666 bytes read in 237 ms (7.4 MiB/s) --->8--- Signed-off-by: Andreas Bießmann <andreas.devel(a)googlemail.com> --- common/cmd_ext_common.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) diff --git a/common/cmd_ext_common.c b/common/cmd_ext_common.c index 1952f4d..57958e6 100644 --- a/common/cmd_ext_common.c +++ b/common/cmd_ext_common.c @@ -76,6 +76,7 @@ int do_ext_load(cmd_tbl_t *cmdtp, int flag, int argc, char buf[12]; unsigned long count; const char *addr_str; + unsigned long time_start; count = 0; addr = simple_strtoul(argv[3], NULL, 16); @@ -135,18 +136,26 @@ int do_ext_load(cmd_tbl_t *cmdtp, int flag, int argc, if ((count < filelen) && (count != 0)) filelen = count; + time_start = get_timer(0); if (ext4fs_read((char *)addr, filelen) != filelen) { printf("** Unable to read \"%s\" from %s %d:%d **\n", filename, argv[1], dev, part); ext4fs_close(); goto fail; } + time_start = get_timer(time_start); ext4fs_close(); /* Loading ok, update default load address */ load_addr = addr; - printf("%d bytes read\n", filelen); + printf("%d bytes read in %lu ms", filelen, time_start); + if (time_start > 0) { + puts(" ("); + print_size(filelen / time_start * 1000, "/s"); + puts(")"); + } + puts("\n"); sprintf(buf, "%X", filelen); setenv("filesize", buf); -- 1.7.10.4

4 8

[U-Boot] [PATCH] fs: zfs: fix illegal use of fp
by Alejandro Mery 14 Nov '12

14 Nov '12

the upcoming sunxi (allwinner a10/a13) platform enables zfs by default, and using linaro's hf -msoft-float makes the build fail because this u64 division. Signed-off-by: Alejandro Mery <amery(a)geeks.cl> --- fs/zfs/zfs.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/fs/zfs/zfs.c b/fs/zfs/zfs.c index 360f723..ff857ae 100644 --- a/fs/zfs/zfs.c +++ b/fs/zfs/zfs.c @@ -30,6 +30,7 @@ #include <linux/ctype.h> #include <asm/byteorder.h> #include "zfs_common.h" +#include "div64.h" block_dev_desc_t *zfs_dev_desc; @@ -2158,7 +2159,8 @@ zfs_read(zfs_file_t file, char *buf, uint64_t len) /* * Find requested blkid and the offset within that block. */ - uint64_t blkid = (file->offset + red) / blksz; + uint64_t blkid = file->offset + red; + blkid = do_div(blkid, blksz); free(data->file_buf); data->file_buf = 0; -- 1.7.12.3

3 2

[U-Boot] [PATCH] Video: fix compiler warnings in bus_vcxk
by Jens Scharsig (BuS Elektronik) 14 Nov '12

14 Nov '12

From: "Jens Scharsig (BuS Elektronik)" <esw(a)bus-elektronik.de> if a board uses the vcxk driver option CONFIG_SYS_VCXK_DOUBLEBUFFERD, compilier shows warnings. This patch will fix it. Signed-off-by: Jens Scharsig (BuS Elektronik) <esw(a)bus-elektronik.de> --- drivers/video/bus_vcxk.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/video/bus_vcxk.c b/drivers/video/bus_vcxk.c index 9c4714d..a0607cf 100644 --- a/drivers/video/bus_vcxk.c +++ b/drivers/video/bus_vcxk.c @@ -153,7 +153,7 @@ int vcxk_init(unsigned long width, unsigned long height) #ifdef CONFIG_SYS_VCXK_DOUBLEBUFFERED double_bws_word = (u_short *)double_bws; double_bws_long = (u_long *)double_bws; - debug("%lx %lx %lx \n", double_bws, double_bws_word, double_bws_long); + debug("%px %px %px\n", double_bws, double_bws_word, double_bws_long); #endif display_width = width; display_height = height; -- 1.7.10.4

2 1

[U-Boot] [PATCH] M68K: eb_cpu5282: general update and enhanced board support
by Jens Scharsig (BuS Elektronik) 14 Nov '12

14 Nov '12

From: "Jens Scharsig (BuS Elektronik)" <esw(a)bus-elektronik.de> - update clock settings for higher perfomance - change standard baud rate to 115200 - fix flash base address - remove unused defines - add I2C support - switch form board dependent flash to cfi - remove board dependent flash code - use sdram bank 0 instead of bank 1 on boot - enable on board frame buffer instead external - remove fake mac address form config - add watchdog support - add status led support Signed-off-by: Jens Scharsig (BuS Elektronik) <esw(a)bus-elektronik.de> --- board/BuS/eb_cpu5282/Makefile | 2 +- board/BuS/eb_cpu5282/cfm_flash.c | 212 ------------------- board/BuS/eb_cpu5282/cfm_flash.h | 40 ---- board/BuS/eb_cpu5282/config.mk | 27 --- board/BuS/eb_cpu5282/eb_cpu5282.c | 102 ++++++--- board/BuS/eb_cpu5282/flash.c | 415 ------------------------------------- boards.cfg | 2 +- include/configs/eb_cpu5282.h | 101 +++++---- 8 files changed, 142 insertions(+), 759 deletions(-) delete mode 100644 board/BuS/eb_cpu5282/cfm_flash.c delete mode 100644 board/BuS/eb_cpu5282/cfm_flash.h delete mode 100644 board/BuS/eb_cpu5282/config.mk delete mode 100644 board/BuS/eb_cpu5282/flash.c diff --git a/board/BuS/eb_cpu5282/Makefile b/board/BuS/eb_cpu5282/Makefile index 0f14699..ac860c1 100644 --- a/board/BuS/eb_cpu5282/Makefile +++ b/board/BuS/eb_cpu5282/Makefile @@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o -COBJS = $(BOARD).o cfm_flash.o flash.o +COBJS = $(BOARD).o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) diff --git a/board/BuS/eb_cpu5282/cfm_flash.c b/board/BuS/eb_cpu5282/cfm_flash.c deleted file mode 100644 index fe03b17..0000000 --- a/board/BuS/eb_cpu5282/cfm_flash.c +++ /dev/null @@ -1,212 +0,0 @@ -/* - * Basic Flash Driver for Freescale MCF 5281/5282 internal FLASH - * - * (C) Copyright 2005 BuS Elektronik GmbH & Co.KG <esw(a)bus-elektonik.de> - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <common.h> -#include <asm/m5282.h> -#include "cfm_flash.h" - -#if defined(CONFIG_M5281) || defined(CONFIG_M5282) - -#if (CONFIG_SYS_CLK>20000000) - #define CFM_CLK (((long) CONFIG_SYS_CLK / (400000 * 8) + 1) | 0x40) -#else - #define CFM_CLK ((long) CONFIG_SYS_CLK / 400000 + 1) -#endif - -#define cmf_backdoor_address(addr) (((addr) & 0x0007FFFF) | 0x04000000 | \ - (CONFIG_SYS_MBAR & 0xC0000000)) - -void cfm_flash_print_info (flash_info_t * info) -{ - printf ("Freescale: "); - switch (info->flash_id & FLASH_TYPEMASK) { - case FREESCALE_ID_MCF5281 & FLASH_TYPEMASK: - printf ("MCF5281 internal FLASH\n"); - break; - case FREESCALE_ID_MCF5282 & FLASH_TYPEMASK: - printf ("MCF5282 internal FLASH\n"); - break; - default: - printf ("Unknown Chip Type\n"); - break; - } -} - -void cfm_flash_init (flash_info_t * info) -{ - int sector; - ulong protection; - MCFCFM_MCR = 0; - MCFCFM_CLKD = CFM_CLK; - debug ("CFM Clock divider: %ld (%d Hz @ %ld Hz)\n",CFM_CLK,\ - CONFIG_SYS_CLK / (2* ((CFM_CLK & 0x3F)+1) * (1+((CFM_CLK & 0x40)>>6)*7)),\ - CONFIG_SYS_CLK); - MCFCFM_SACC = 0; - MCFCFM_DACC = 0; - - if (MCFCFM_SEC & MCFCFM_SEC_KEYEN) - puts("CFM backdoor access is enabled\n"); - if (MCFCFM_SEC & MCFCFM_SEC_SECSTAT) - puts("CFM securety is enabled\n"); - - #ifdef CONFIG_M5281 - info->flash_id = (FREESCALE_MANUFACT & FLASH_VENDMASK) | - (FREESCALE_ID_MCF5281 & FLASH_TYPEMASK); - info->size = 256*1024; - info->sector_count = 16; - #else - info->flash_id = (FREESCALE_MANUFACT & FLASH_VENDMASK) | - (FREESCALE_ID_MCF5282 & FLASH_TYPEMASK); - info->size = 512*1024; - info->sector_count = 32; - #endif - protection = MCFCFM_PROT; - for (sector = 0; sector < info->sector_count; sector++) - { - if (sector == 0) - { - info->start[sector] = CONFIG_SYS_INT_FLASH_BASE; - } - else - { - info->start[sector] = info->start[sector-1] + 0x04000; - } - info->protect[sector] = protection & 1; - protection >>= 1; - } -} - -int cfm_flash_readycheck(int checkblank) -{ - int rc; - unsigned char state; - - rc = ERR_OK; - while (!(MCFCFM_USTAT & MCFCFM_USTAT_CCIF)); - state = MCFCFM_USTAT; - if (state & MCFCFM_USTAT_ACCERR) - { - debug ("%s(): CFM access error",__FUNCTION__); - rc = ERR_PROG_ERROR; - } - if (state & MCFCFM_USTAT_PVIOL) - { - debug ("%s(): CFM protection violation",__FUNCTION__); - rc = ERR_PROTECTED; - } - if (checkblank) - { - if (!(state & MCFCFM_USTAT_BLANK)) - { - debug ("%s(): CFM erras error",__FUNCTION__); - rc = ERR_NOT_ERASED; - } - } - MCFCFM_USTAT = state & 0x34; /* reset state */ - return rc; -} - -/* Erase 16KiB = 8 2KiB pages */ - -int cfm_flash_erase_sector (flash_info_t * info, int sector) -{ - ulong address; - int page; - int rc; - rc= ERR_OK; - address = cmf_backdoor_address(info->start[sector]); - for (page=0; (page<8) && (rc==ERR_OK); page++) - { - *(volatile __u32*) address = 0; - MCFCFM_CMD = MCFCFM_CMD_PGERS; - MCFCFM_USTAT = MCFCFM_USTAT_CBEIF; - rc = cfm_flash_readycheck(0); - if (rc==ERR_OK) - { - *(volatile __u32*) address = 0; - MCFCFM_CMD = MCFCFM_CMD_PGERSVER; - MCFCFM_USTAT = MCFCFM_USTAT_CBEIF; - rc = cfm_flash_readycheck(1); - } - address += 0x800; - } - return rc; -} - -int cfm_flash_write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt) -{ - int rc; - ulong dest, data; - - rc = ERR_OK; - if (addr & 3) - { - debug ("Byte and Word alignment not supported\n"); - rc = ERR_ALIGN; - } - if (cnt & 3) - { - debug ("Byte and Word transfer not supported\n"); - rc = ERR_ALIGN; - } - dest = cmf_backdoor_address(addr); - while ((cnt>=4) && (rc == ERR_OK)) - { - data = *((volatile u32 *) src); - *(volatile u32*) dest = data; - MCFCFM_CMD = MCFCFM_CMD_PGM; - MCFCFM_USTAT = MCFCFM_USTAT_CBEIF; - rc = cfm_flash_readycheck(0); - if (*(volatile u32*) addr != data) rc = ERR_PROG_ERROR; - src +=4; - dest +=4; - addr +=4; - cnt -=4; - } - return rc; -} - -#ifdef CONFIG_SYS_FLASH_PROTECTION - -int cfm_flash_protect(flash_info_t * info,long sector,int prot) -{ - int rc; - - rc= ERR_OK; - if (prot) - { - MCFCFM_PROT |= (1<<sector); - info->protect[sector]=1; - } - else - { - MCFCFM_PROT &= ~(1<<sector); - info->protect[sector]=0; - } - return rc; -} - -#endif - -#endif diff --git a/board/BuS/eb_cpu5282/cfm_flash.h b/board/BuS/eb_cpu5282/cfm_flash.h deleted file mode 100644 index ed4e794..0000000 --- a/board/BuS/eb_cpu5282/cfm_flash.h +++ /dev/null @@ -1,40 +0,0 @@ -/* - * Basic Flash Driver for Freescale MCF 5282 internal FLASH - * - * (C) Copyright 2005 BuS Elektronik GmbH & Co.KG <esw(a)bus-elektonik.de> - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef __CFM_FLASH_H_ -#define __CFM_FLASH_H_ - -#define FREESCALE_MANUFACT 0xFACFFACF -#define FREESCALE_ID_MCF5281 0x5281 -#define FREESCALE_ID_MCF5282 0x5282 - -extern void cfm_flash_print_info (flash_info_t * info); -extern int cfm_flash_erase_sector (flash_info_t * info, int sector); -extern void cfm_flash_init (flash_info_t * info); -extern int cfm_flash_write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt); -#ifdef CONFIG_SYS_FLASH_PROTECTION -extern int cfm_flash_protect(flash_info_t * info,long sector,int prot); -#endif - -#endif diff --git a/board/BuS/eb_cpu5282/config.mk b/board/BuS/eb_cpu5282/config.mk deleted file mode 100644 index 18fb84e..0000000 --- a/board/BuS/eb_cpu5282/config.mk +++ /dev/null @@ -1,27 +0,0 @@ -# -# (C) Copyright 2000-2003 -# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. -# Coldfire contribution by Bernhard Kuhn <bkuhn(a)metrowerks.com> -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -ifndef CONFIG_SYS_TEXT_BASE -CONFIG_SYS_TEXT_BASE = 0xFE000000 -endif diff --git a/board/BuS/eb_cpu5282/eb_cpu5282.c b/board/BuS/eb_cpu5282/eb_cpu5282.c index d64ad1b..231ff77 100644 --- a/board/BuS/eb_cpu5282/eb_cpu5282.c +++ b/board/BuS/eb_cpu5282/eb_cpu5282.c @@ -35,18 +35,19 @@ DECLARE_GLOBAL_DATA_PTR; +#ifdef CONFIG_VIDEO unsigned long display_width; unsigned long display_height; +#endif /*---------------------------------------------------------------------------*/ int checkboard (void) { - puts ("Board: MCF-EV1 + MCF-EV23 (BuS Elektronik GmbH & Co. KG)\n"); + puts("Board: EB+CPU5282 (BuS Elektronik GmbH & Co. KG)\n"); #if (CONFIG_SYS_TEXT_BASE == CONFIG_SYS_INT_FLASH_BASE) - puts (" Boot from Internal FLASH\n"); + puts(" Boot from Internal FLASH\n"); #endif - return 0; } @@ -55,29 +56,39 @@ phys_size_t initdram (int board_type) int size, i; size = 0; - MCFSDRAMC_DCR = MCFSDRAMC_DCR_RTIM_6 - | MCFSDRAMC_DCR_RC ((15 * CONFIG_SYS_CLK) >> 4); + MCFSDRAMC_DCR = MCFSDRAMC_DCR_RTIM_6 | + MCFSDRAMC_DCR_RC((15 * CONFIG_SYS_CLK / 1000000) >> 4); + asm (" nop"); #ifdef CONFIG_SYS_SDRAM_BASE0 - - MCFSDRAMC_DACR0 = MCFSDRAMC_DACR_BASE (CONFIG_SYS_SDRAM_BASE0) - | MCFSDRAMC_DACR_CASL (1) - | MCFSDRAMC_DACR_CBM (3) - | MCFSDRAMC_DACR_PS_16; + MCFSDRAMC_DACR0 = MCFSDRAMC_DACR_BASE(CONFIG_SYS_SDRAM_BASE0)| + MCFSDRAMC_DACR_CASL(1) | MCFSDRAMC_DACR_CBM(3) | + MCFSDRAMC_DACR_PS_32; + asm (" nop"); MCFSDRAMC_DMR0 = MCFSDRAMC_DMR_BAM_16M | MCFSDRAMC_DMR_V; + asm (" nop"); MCFSDRAMC_DACR0 |= MCFSDRAMC_DACR_IP; + asm (" nop"); + for (i = 0; i < 10; i++) + asm (" nop"); - *(unsigned short *) (CONFIG_SYS_SDRAM_BASE0) = 0xA5A5; + *(unsigned long *)(CONFIG_SYS_SDRAM_BASE0) = 0xA5A5A5A5; + asm (" nop"); MCFSDRAMC_DACR0 |= MCFSDRAMC_DACR_RE; + asm (" nop"); + for (i = 0; i < 2000; i++) asm (" nop"); - mbar_writeLong (MCFSDRAMC_DACR0, - mbar_readLong (MCFSDRAMC_DACR0) | MCFSDRAMC_DACR_IMRS); - *(unsigned int *) (CONFIG_SYS_SDRAM_BASE0 + 0x220) = 0xA5A5; - size += CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; + + MCFSDRAMC_DACR0 |= MCFSDRAMC_DACR_IMRS; + asm (" nop"); + /* write SDRAM mode register */ + *(unsigned long *)(CONFIG_SYS_SDRAM_BASE0 + 0x80440) = 0xA5A5A5A5; + asm (" nop"); + size += CONFIG_SYS_SDRAM_SIZE0 * 1024 * 1024; #endif -#ifdef CONFIG_SYS_SDRAM_BASE1 +#ifdef CONFIG_SYS_SDRAM_BASE1xx MCFSDRAMC_DACR1 = MCFSDRAMC_DACR_BASE (CONFIG_SYS_SDRAM_BASE1) | MCFSDRAMC_DACR_CASL (1) | MCFSDRAMC_DACR_CBM (3) @@ -139,19 +150,53 @@ int misc_init_r(void) #ifdef CONFIG_HW_WATCHDOG hw_watchdog_init(); #endif -#ifndef CONFIG_VIDEO - vcxk_init(16, 16); -#endif return 1; } -#if defined(CONFIG_VIDEO) +#if defined(CONFIG_HW_WATCHDOG) -/* - ****h* EB+CPU5282-T1/drv_video_init - * FUNCTION - *** - */ +void hw_watchdog_init(void) +{ + char *s; + int enable; + + enable = 1; + s = getenv("watchdog"); + if (s != NULL) + if ((strncmp(s, "off", 3) == 0) || (strncmp(s, "0", 1) == 0)) + enable = 0; + if (enable) + MCFGPTA_GPTDDR |= (1<<2); + else + MCFGPTA_GPTDDR &= ~(1<<2); +} + +void hw_watchdog_reset(void) +{ + MCFGPTA_GPTPORT ^= (1<<2); +} +#endif + +void __led_toggle(led_id_t mask) +{ + MCFGPTA_GPTPORT ^= (1 << 3); +} + +void __led_init(led_id_t mask, int state) +{ + __led_set(mask, state); + MCFGPTA_GPTDDR |= (1 << 3) ; +} + +void __led_set(led_id_t mask, int state) +{ + if (state == STATUS_LED_ON) + MCFGPTA_GPTPORT |= (1 << 3); + else + MCFGPTA_GPTPORT &= ~(1 << 3); +} + +#if defined(CONFIG_VIDEO) int drv_video_init(void) { @@ -159,13 +204,14 @@ int drv_video_init(void) unsigned long splash; printf("Init Video as "); - - if ((s = getenv("displaywidth")) != NULL) + s = getenv("displaywidth"); + if (s != NULL) display_width = simple_strtoul(s, NULL, 10); else display_width = 256; - if ((s = getenv("displayheight")) != NULL) + s = getenv("displayheight"); + if (s != NULL) display_height = simple_strtoul(s, NULL, 10); else display_height = 256; diff --git a/board/BuS/eb_cpu5282/flash.c b/board/BuS/eb_cpu5282/flash.c deleted file mode 100644 index 8b7f957..0000000 --- a/board/BuS/eb_cpu5282/flash.c +++ /dev/null @@ -1,415 +0,0 @@ -/* - * (C) Copyright 2005 - * BuS Elektronik GmbH & Co.KG <esw(a)bus-elektonik.de> - * - * Based On - * Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <common.h> -#include "cfm_flash.h" - -#define PHYS_FLASH_1 CONFIG_SYS_FLASH_BASE -#define FLASH_BANK_SIZE 0x200000 - -flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; - -void flash_print_info (flash_info_t * info) -{ - int i; - - switch (info->flash_id & FLASH_VENDMASK) { - case (AMD_MANUFACT & FLASH_VENDMASK): - printf ("AMD: "); - switch (info->flash_id & FLASH_TYPEMASK) { - case (AMD_ID_LV160B & FLASH_TYPEMASK): - printf ("AM29LV160B (16Bit)\n"); - break; - default: - printf ("Unknown Chip Type\n"); - break; - } - break; - case FREESCALE_MANUFACT & FLASH_VENDMASK: - cfm_flash_print_info (info); - break; - default: - printf ("Unknown Vendor "); - break; - } - - puts (" Size: "); - if ((info->size >> 20) > 0) - { - printf ("%ld MiB",info->size >> 20); - } - else - { - printf ("%ld KiB",info->size >> 10); - } - printf (" in %d Sectors\n", info->sector_count); - - printf (" Sector Start Addresses:"); - for (i = 0; i < info->sector_count; i++) { - if ((i % 4) == 0) { - printf ("\n "); - } - printf ("%02d: %08lX%s ", i,info->start[i], - info->protect[i] ? " P" : " "); - } - printf ("\n\n"); -} - -unsigned long flash_init (void) -{ - int i, j; - ulong size = 0; - - for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) { - ulong flashbase = 0; - - switch (i) - { - case 1: - flash_info[i].flash_id = - (AMD_MANUFACT & FLASH_VENDMASK) | - (AMD_ID_LV160B & FLASH_TYPEMASK); - flash_info[i].size = FLASH_BANK_SIZE; - flash_info[i].sector_count = CONFIG_SYS_MAX_FLASH_SECT; - memset (flash_info[i].protect, 0, CONFIG_SYS_MAX_FLASH_SECT); - flashbase = PHYS_FLASH_1; - for (j = 0; j < flash_info[i].sector_count; j++) { - if (j == 0) { - /* 1st is 16 KiB */ - flash_info[i].start[j] = flashbase; - } - if ((j >= 1) && (j <= 2)) { - /* 2nd and 3rd are 8 KiB */ - flash_info[i].start[j] = - flashbase + 0x4000 + 0x2000 * (j - 1); - } - if (j == 3) { - /* 4th is 32 KiB */ - flash_info[i].start[j] = flashbase + 0x8000; - } - if ((j >= 4) && (j <= 34)) { - /* rest is 256 KiB */ - flash_info[i].start[j] = - flashbase + 0x10000 + 0x10000 * (j - 4); - } - } - break; - case 0: - cfm_flash_init (&flash_info[i]); - break; - default: - panic ("configured to many flash banks!\n"); - } - - size += flash_info[i].size; - } - - flash_protect (FLAG_PROTECT_SET, - CONFIG_SYS_FLASH_BASE, - CONFIG_SYS_FLASH_BASE + 0xffff, &flash_info[0]); - - return size; -} - -#define CMD_READ_ARRAY 0x00F0 -#define CMD_UNLOCK1 0x00AA -#define CMD_UNLOCK2 0x0055 -#define CMD_ERASE_SETUP 0x0080 -#define CMD_ERASE_CONFIRM 0x0030 -#define CMD_PROGRAM 0x00A0 -#define CMD_UNLOCK_BYPASS 0x0020 - -#define MEM_FLASH_ADDR1 (*(volatile u16 *)(info->start[0] + (0x00000555<<1))) -#define MEM_FLASH_ADDR2 (*(volatile u16 *)(info->start[0] + (0x000002AA<<1))) - - -#define BIT_ERASE_DONE 0x0080 -#define BIT_RDY_MASK 0x0080 -#define BIT_PROGRAM_ERROR 0x0020 -#define BIT_TIMEOUT 0x80000000 /* our flag */ - -#define ERR_READY -1 - -int amd_flash_erase_sector(flash_info_t * info, int sector) -{ - int state; - ulong result; - ulong start; - - volatile u16 *addr = - (volatile u16 *) (info->start[sector]); - - MEM_FLASH_ADDR1 = CMD_UNLOCK1; - MEM_FLASH_ADDR2 = CMD_UNLOCK2; - MEM_FLASH_ADDR1 = CMD_ERASE_SETUP; - - MEM_FLASH_ADDR1 = CMD_UNLOCK1; - MEM_FLASH_ADDR2 = CMD_UNLOCK2; - *addr = CMD_ERASE_CONFIRM; - - /* wait until flash is ready */ - state = 0; - start = get_timer(0); - - do { - result = *addr; - - /* check timeout */ - if (get_timer(start) > CONFIG_SYS_FLASH_ERASE_TOUT) { - MEM_FLASH_ADDR1 = CMD_READ_ARRAY; - state = ERR_TIMOUT; - } - - if (!state && (result & 0xFFFF) & BIT_ERASE_DONE) - state = ERR_READY; - } - while (!state); - if (state == ERR_READY) - state = ERR_OK; - - MEM_FLASH_ADDR1 = CMD_READ_ARRAY; - - return state; -} - -int flash_erase (flash_info_t * info, int s_first, int s_last) -{ - int iflag, cflag; - int sector; - int rc; - - rc = ERR_OK; - - if (info->flash_id == FLASH_UNKNOWN) - { - rc = ERR_UNKNOWN_FLASH_TYPE; - } /* (info->flash_id == FLASH_UNKNOWN) */ - - if ((s_first < 0) || (s_first > s_last) || s_last >= info->sector_count) - { - rc = ERR_INVAL; - } - - cflag = icache_status (); - icache_disable (); - iflag = disable_interrupts (); - - for (sector = s_first; (sector <= s_last) && (rc == ERR_OK); sector++) { - - if (info->protect[sector]) - { - putc('P'); /* protected sector will not erase */ - } - else - { - /* erase on unprotected sector */ - puts("E\b"); - switch (info->flash_id & FLASH_VENDMASK) - { - case (AMD_MANUFACT & FLASH_VENDMASK): - rc = amd_flash_erase_sector(info,sector); - break; - case (FREESCALE_MANUFACT & FLASH_VENDMASK): - rc = cfm_flash_erase_sector(info,sector); - break; - default: - return ERR_UNKNOWN_FLASH_VENDOR; - } - putc('.'); - } - } - if (rc!=ERR_OK) - { - printf ("\n "); - flash_perror (rc); - } - else - { - printf (" done\n"); - } - - udelay (10000); /* allow flash to settle - wait 10 ms */ - - if (iflag) - enable_interrupts (); - - if (cflag) - icache_enable (); - - return rc; -} - -volatile static int amd_write_word (flash_info_t * info, ulong dest, u16 data) -{ - volatile u16 *addr; - ulong result; - int cflag, iflag; - int state; - ulong start; - - /* - * Check if Flash is (sufficiently) erased - */ - addr = (volatile u16 *) dest; - - result = *addr; - if ((result & data) != data) - return ERR_NOT_ERASED; - - /* - * Disable interrupts which might cause a timeout - * here. Remember that our exception vectors are - * at address 0 in the flash, and we don't want a - * (ticker) exception to happen while the flash - * chip is in programming mode. - */ - - cflag = icache_status (); - icache_disable (); - iflag = disable_interrupts (); - - MEM_FLASH_ADDR1 = CMD_UNLOCK1; - MEM_FLASH_ADDR2 = CMD_UNLOCK2; - MEM_FLASH_ADDR1 = CMD_PROGRAM; - *addr = data; - - /* arm simple, non interrupt dependent timer */ - start = get_timer(0); - - /* wait until flash is ready */ - state = 0; - do { - result = *addr; - - /* check timeout */ - if (get_timer(start) > CONFIG_SYS_FLASH_ERASE_TOUT) { - state = ERR_TIMOUT; - } - if (!state && ((result & BIT_RDY_MASK) == (data & BIT_RDY_MASK))) - state = ERR_READY; - - } while (!state); - - *addr = CMD_READ_ARRAY; - - if (state == ERR_READY) - state = ERR_OK; - if ((*addr != data) && (state != ERR_TIMOUT)) - state = ERR_PROG_ERROR; - - if (iflag) - enable_interrupts (); - - if (cflag) - icache_enable (); - - return state; -} - -int amd_flash_write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt) -{ - int rc; - ulong dest; - u16 data; - - rc = ERR_OK; - if (addr & 1) - { - debug ("Byte alignment not supported\n"); - rc = ERR_ALIGN; - } - if (cnt & 1) - { - debug ("Byte transfer not supported\n"); - rc = ERR_ALIGN; - } - - dest = addr; - while ((cnt>=2) && (rc == ERR_OK)) - { - data = *((volatile u16 *) src); - rc=amd_write_word (info,dest,data); - src +=2; - dest +=2; - cnt -=2; - } - return rc; -} - -int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt) -{ - int rc; - - switch (info->flash_id & FLASH_VENDMASK) - { - case (AMD_MANUFACT & FLASH_VENDMASK): - rc = amd_flash_write_buff(info,src,addr,cnt); - break; - case (FREESCALE_MANUFACT & FLASH_VENDMASK): - rc = cfm_flash_write_buff(info,src,addr,cnt); - break; - default: - rc = ERR_UNKNOWN_FLASH_VENDOR; - } - return rc; - -} -int amd_flash_protect(flash_info_t * info,long sector,int prot) -{ - int rc; - rc= ERR_OK; - if (prot) - { - info->protect[sector]=1; - } - else - { - info->protect[sector]=0; - } - return rc; -} - -#ifdef CONFIG_SYS_FLASH_PROTECTION - -int flash_real_protect(flash_info_t * info,long sector,int prot) -{ - int rc; - - switch (info->flash_id & FLASH_VENDMASK) - { - case (AMD_MANUFACT & FLASH_VENDMASK): - rc = amd_flash_protect(info,sector,prot); - break; - case (FREESCALE_MANUFACT & FLASH_VENDMASK): - rc = cfm_flash_protect(info,sector,prot); - break; - default: - rc = ERR_UNKNOWN_FLASH_VENDOR; - } - return rc; -} - -#endif diff --git a/boards.cfg b/boards.cfg index 7c1fc74..07699f7 100644 --- a/boards.cfg +++ b/boards.cfg @@ -361,7 +361,7 @@ M5235EVB m68k mcf523x m5235evb freesca M5235EVB_Flash32 m68k mcf523x m5235evb freescale - M5235EVB:NORFLASH_PS32BIT,SYS_TEXT_BASE=0xFFC00000 cobra5272 m68k mcf52x2 cobra5272 - idmr m68k mcf52x2 -eb_cpu5282 m68k mcf52x2 eb_cpu5282 BuS - eb_cpu5282:SYS_TEXT_BASE=0xFFE00000 +eb_cpu5282 m68k mcf52x2 eb_cpu5282 BuS - eb_cpu5282:SYS_TEXT_BASE=0xFF000000 eb_cpu5282_internal m68k mcf52x2 eb_cpu5282 BuS - eb_cpu5282:SYS_TEXT_BASE=0xF0000000 TASREG m68k mcf52x2 tasreg esd M5208EVBE m68k mcf52x2 m5208evbe freescale diff --git a/include/configs/eb_cpu5282.h b/include/configs/eb_cpu5282.h index 9ecc10b..f1ce94e 100644 --- a/include/configs/eb_cpu5282.h +++ b/include/configs/eb_cpu5282.h @@ -38,7 +38,7 @@ #define CONFIG_MCFUART #define CONFIG_SYS_UART_PORT (0) -#define CONFIG_BAUDRATE 9600 +#define CONFIG_BAUDRATE 115200 #undef CONFIG_MONITOR_IS_IN_RAM /* starts uboot direct */ @@ -52,20 +52,24 @@ #define CONFIG_RESET_TO_RETRY #define CONFIG_SPLASH_SCREEN +#define CONFIG_HW_WATCHDOG + +#define CONFIG_STATUS_LED +#define CONFIG_BOARD_SPECIFIC_LED +#define STATUS_LED_ACTIVE 0 +#define STATUS_LED_BIT 0x0008 /* Timer7 GPIO */ +#define STATUS_LED_BOOT 0 +#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) +#define STATUS_LED_STATE STATUS_LED_OFF + /*----------------------------------------------------------------------* * Configuration for environment * * Environment is in the second sector of the first 256k of flash * *----------------------------------------------------------------------*/ -#ifndef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_ENV_ADDR 0xF003C000 /* End of 256K */ -#define CONFIG_ENV_SECT_SIZE 0x4000 -#define CONFIG_ENV_IS_IN_FLASH 1 -#else -#define CONFIG_ENV_ADDR 0xFFE04000 -#define CONFIG_ENV_SECT_SIZE 0x2000 +#define CONFIG_ENV_ADDR 0xFF040000 +#define CONFIG_ENV_SECT_SIZE 0x00020000 #define CONFIG_ENV_IS_IN_FLASH 1 -#endif /* * BOOTP options @@ -78,26 +82,24 @@ /* * Command line configuration. */ +#define CONFIG_CMDLINE_EDITING #include <config_cmd_default.h> #undef CONFIG_CMD_LOADB +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_I2C +#define CONFIG_CMD_LED #define CONFIG_CMD_MII #define CONFIG_CMD_NET #define CONFIG_MCFTMR - #define CONFIG_BOOTDELAY 5 -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #define CONFIG_SYS_PROMPT "\nEB+CPU5282> " #define CONFIG_SYS_LONGHELP 1 -#if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE @@ -112,12 +114,12 @@ /*----------------------------------------------------------------------* * Clock and PLL Configuration * *----------------------------------------------------------------------*/ -#define CONFIG_SYS_HZ 10000000 -#define CONFIG_SYS_CLK 58982400 /* 9,8304MHz * 6 */ +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_CLK 80000000 /* 8MHz * 8 */ -/* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */ +/* PLL Configuration: Ext Clock * 8 (see table 9-4 of MCF user manual) */ -#define CONFIG_SYS_MFD 0x01 /* PLL Multiplication Factor Devider */ +#define CONFIG_SYS_MFD 0x02 /* PLL Multiplication Factor Devider */ #define CONFIG_SYS_RFD 0x00 /* PLL Reduce Frecuency Devider */ /*----------------------------------------------------------------------* @@ -135,7 +137,6 @@ #define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE #define MCFFEC_TOUT_LOOP 50000 -#define CONFIG_ETHADDR 00:CF:52:82:EB:01 #define CONFIG_OVERWRITE_ETHADDR_ONCE /*------------------------------------------------------------------------- @@ -151,7 +152,7 @@ *-----------------------------------------------------------------------*/ #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 +#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 #define CONFIG_SYS_GBL_DATA_OFFSET \ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET @@ -161,12 +162,11 @@ * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CONFIG_SYS_SDRAM_BASE1 0x00000000 -#define CONFIG_SYS_SDRAM_SIZE1 16 /* SDRAM size in MB */ - -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM_BASE1 -#define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_SDRAM_SIZE1 +#define CONFIG_SYS_SDRAM_BASE0 0x00000000 +#define CONFIG_SYS_SDRAM_SIZE0 16 /* SDRAM size in MB */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM_BASE0 +#define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_SDRAM_SIZE0 /* If M5282 port is fully implemented the monitor base will be behind * the vector table. */ @@ -190,16 +190,24 @@ /*----------------------------------------------------------------------- * FLASH organization */ +#define CONFIG_FLASH_SHOW_PROGRESS 45 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE #define CONFIG_SYS_INT_FLASH_BASE 0xF0000000 #define CONFIG_SYS_INT_FLASH_ENABLE 0x21 -#define CONFIG_SYS_MAX_FLASH_SECT 35 -#define CONFIG_SYS_MAX_FLASH_BANKS 2 +#define CONFIG_SYS_MAX_FLASH_SECT 128 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 #define CONFIG_SYS_FLASH_ERASE_TOUT 10000000 #define CONFIG_SYS_FLASH_PROTECTION +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_SIZE 16*1024*1024 +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT + +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } + /*----------------------------------------------------------------------- * Cache Configuration */ @@ -221,12 +229,16 @@ * Memory bank definitions */ -#define CONFIG_SYS_CS0_BASE 0xFFE00000 +#define CONFIG_SYS_CS0_BASE 0xFF000000 #define CONFIG_SYS_CS0_CTRL 0x00001980 -#define CONFIG_SYS_CS0_MASK 0x001F0001 +#define CONFIG_SYS_CS0_MASK 0x00FF0001 -#define CONFIG_SYS_CS3_BASE 0xE0000000 -#define CONFIG_SYS_CS0_CTRL 0x00001980 +#define CONFIG_SYS_CS2_BASE 0xE0000000 +#define CONFIG_SYS_CS2_CTRL 0x00001980 +#define CONFIG_SYS_CS2_MASK 0x000F0001 + +#define CONFIG_SYS_CS3_BASE 0xE0100000 +#define CONFIG_SYS_CS3_CTRL 0x00001980 #define CONFIG_SYS_CS3_MASK 0x000F0001 /*----------------------------------------------------------------------- @@ -248,23 +260,42 @@ #define CONFIG_SYS_PCDDR 0x0000000 #define CONFIG_SYS_PCDAT 0x0000000 +#define CONFIG_SYS_PASPAR 0x0F0F #define CONFIG_SYS_PEHLPAR 0xC0 #define CONFIG_SYS_PUAPAR 0x0F #define CONFIG_SYS_DDRUA 0x05 #define CONFIG_SYS_PJPAR 0xFF /*----------------------------------------------------------------------- + * I2C + */ + +#define CONFIG_HARD_I2C +#define CONFIG_FSL_I2C + +#define CONFIG_SYS_I2C_OFFSET 0x00000300 +#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR + +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SLAVE 0 + +#ifdef CONFIG_CMD_DATE +#define CONFIG_RTC_DS1338 +#define CONFIG_I2C_RTC_ADDR 0x68 +#endif + +/*----------------------------------------------------------------------- * VIDEO configuration */ #define CONFIG_VIDEO #ifdef CONFIG_VIDEO -#define CONFIG_VIDEO_VCXK 1 +#define CONFIG_VIDEO_VCXK 1 #define CONFIG_SYS_VCXK_DEFAULT_LINEALIGN 2 #define CONFIG_SYS_VCXK_DOUBLEBUFFERED 1 -#define CONFIG_SYS_VCXK_BASE CONFIG_SYS_CS3_BASE +#define CONFIG_SYS_VCXK_BASE CONFIG_SYS_CS2_BASE #define CONFIG_SYS_VCXK_AUTODETECT 1 #define CONFIG_SYS_VCXK_ACKNOWLEDGE_PORT MCFGPTB_GPTPORT -- 1.7.10.4

3 4

[U-Boot] v2013.01-rc1 released
by Tom Rini 14 Nov '12

14 Nov '12

Hey all, With the official closing of the merge window just past us now, I've tagged v2013.01-rc1. I expect a number of pull requests still covering all of the patches that have been posted before the merge window closed and are ready to pull, but haven't yet. Since we have tagged -rc1 that does mean that I'd really like it if folks can focus on their current patch sets before starting off on new projects too. And please, please give things a whirl on your hardware, there have been a lot of changes made in some important areas. Thanks all! -- Tom

4 4

[U-Boot] [PATCH V3 00/12] Blackfin: add new processor and board
by Bob Liu 14 Nov '12

14 Nov '12

Blackfin bf60x is a new processor for blackfin. This series patches add some basic support for it with a bf609-ezkit reference board. I got some suggestion in the former commit. Some of them are fixed, but some is still not clear. Since it's a long time ago, i send out V3 for feedback. Bob Liu (7): Blackfin: bf60x: new processor header files Blackfin: bf60x: add dma support Blackfin: bf60x: support big cplb page Blackfin: bf60x: add gpio support Blackfin: bf60x: core support blackfin: bf609: add board support Blackfin: bf60x: add hw watchdog support Scott Jiang (1): Blackfin: spi: add bf6xx spi driver Sonic Zhang (3): Blackfin: bf60x: add serial support Blackfin: bf60x: add rsi/sdh support Blackfin: bf609-ezkit: implement soft switch Steven Miao (1): Blackfin: Bf60x: add resume from hibernate MAINTAINERS | 1 + arch/blackfin/cpu/cpu.c | 4 +- arch/blackfin/cpu/gpio.c | 36 +- arch/blackfin/cpu/initcode.c | 365 +- arch/blackfin/cpu/initcode.h | 52 + arch/blackfin/cpu/reset.c | 6 + arch/blackfin/cpu/serial.c | 81 +- arch/blackfin/cpu/serial.h | 222 +- arch/blackfin/cpu/serial1.h | 275 ++ arch/blackfin/cpu/serial4.h | 139 + arch/blackfin/cpu/start.S | 2 + arch/blackfin/include/asm/blackfin_cdef.h | 3 + arch/blackfin/include/asm/blackfin_def.h | 5 + arch/blackfin/include/asm/blackfin_local.h | 3 + arch/blackfin/include/asm/config-pre.h | 4 + arch/blackfin/include/asm/cplb.h | 17 +- arch/blackfin/include/asm/dma.h | 113 +- arch/blackfin/include/asm/gpio.h | 2 +- arch/blackfin/include/asm/mach-bf609/BF609_cdef.h | 543 +++ arch/blackfin/include/asm/mach-bf609/BF609_def.h | 3758 ++++++++++++++++++++ arch/blackfin/include/asm/mach-bf609/anomaly.h | 128 + arch/blackfin/include/asm/mach-bf609/def_local.h | 5 + arch/blackfin/include/asm/mach-bf609/gpio.h | 151 + arch/blackfin/include/asm/mach-bf609/portmux.h | 257 ++ arch/blackfin/include/asm/mach-bf609/ports.h | 103 + arch/blackfin/include/asm/mach-common/bits/cgu.h | 80 + arch/blackfin/include/asm/mach-common/bits/dde.h | 88 + arch/blackfin/include/asm/mach-common/bits/dma.h | 48 +- arch/blackfin/include/asm/mach-common/bits/mpu.h | 6 +- arch/blackfin/include/asm/mach-common/bits/pll.h | 5 + arch/blackfin/include/asm/mach-common/bits/sdh.h | 38 +- .../blackfin/include/asm/mach-common/bits/spi6xx.h | 240 ++ arch/blackfin/include/asm/mach-common/bits/uart4.h | 66 + arch/blackfin/lib/board.c | 33 +- arch/blackfin/lib/clocks.c | 113 +- arch/blackfin/lib/string.c | 97 +- board/bf609-ezkit/Makefile | 55 + board/bf609-ezkit/bf609-ezkit.c | 67 + board/bf609-ezkit/soft_switch.c | 169 + board/bf609-ezkit/soft_switch.h | 71 + boards.cfg | 1 + common/cmd_reginfo.c | 19 +- drivers/mmc/bfin_sdh.c | 68 +- drivers/spi/Makefile | 1 + drivers/spi/bfin_spi6xx.c | 308 ++ include/configs/bf609-ezkit.h | 175 + include/configs/bfin_adi_common.h | 8 +- 47 files changed, 7611 insertions(+), 420 deletions(-) create mode 100644 arch/blackfin/cpu/serial1.h create mode 100644 arch/blackfin/cpu/serial4.h create mode 100644 arch/blackfin/include/asm/mach-bf609/BF609_cdef.h create mode 100644 arch/blackfin/include/asm/mach-bf609/BF609_def.h create mode 100644 arch/blackfin/include/asm/mach-bf609/anomaly.h create mode 100644 arch/blackfin/include/asm/mach-bf609/def_local.h create mode 100644 arch/blackfin/include/asm/mach-bf609/gpio.h create mode 100644 arch/blackfin/include/asm/mach-bf609/portmux.h create mode 100644 arch/blackfin/include/asm/mach-bf609/ports.h create mode 100644 arch/blackfin/include/asm/mach-common/bits/cgu.h create mode 100644 arch/blackfin/include/asm/mach-common/bits/dde.h create mode 100644 arch/blackfin/include/asm/mach-common/bits/spi6xx.h create mode 100644 arch/blackfin/include/asm/mach-common/bits/uart4.h create mode 100644 board/bf609-ezkit/Makefile create mode 100644 board/bf609-ezkit/bf609-ezkit.c create mode 100644 board/bf609-ezkit/soft_switch.c create mode 100644 board/bf609-ezkit/soft_switch.h create mode 100644 drivers/spi/bfin_spi6xx.c create mode 100644 include/configs/bf609-ezkit.h -- 1.7.9.5

1 12

[U-Boot] [PATCH] nand_spl: fix u-boot.lst breakage
by Scott Wood 14 Nov '12

14 Nov '12

Commit 97b24d3d51a92cb8c0c1e1a74abf22fe1a1807a3 "common: Add symbol handling for generic lists into Makefile" introduced build errors in many nand_spl targets, complaining of a missing u-boot.lst. When not doing an out-of-tree build, $(obj) expands to nothing, so GCC ended up being given -I with no argument (or rather, -ansi was the argument). The failure didn't show up during a -j1 build because it was picking up the non-SPL version of u-boot.lst. Signed-off-by: Scott Wood <scottwood(a)freescale.com> --- I didn't fix p1_p2_rdb_pc because that will just conflict with the patchset that migrates that target away from nand_spl. nand_spl/board/freescale/mpc8536ds/Makefile | 3 ++- nand_spl/board/freescale/mpc8569mds/Makefile | 3 ++- nand_spl/board/freescale/mpc8572ds/Makefile | 3 ++- nand_spl/board/freescale/mx31pdk/Makefile | 3 ++- nand_spl/board/freescale/p1010rdb/Makefile | 3 ++- nand_spl/board/freescale/p1023rds/Makefile | 3 ++- nand_spl/board/freescale/p1_p2_rdb/Makefile | 3 ++- nand_spl/board/karo/tx25/Makefile | 3 ++- 8 files changed, 16 insertions(+), 8 deletions(-) diff --git a/nand_spl/board/freescale/mpc8536ds/Makefile b/nand_spl/board/freescale/mpc8536ds/Makefile index c923557..9c77826 100644 --- a/nand_spl/board/freescale/mpc8536ds/Makefile +++ b/nand_spl/board/freescale/mpc8536ds/Makefile @@ -67,7 +67,8 @@ $(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot-nand_spl.lds # $(LDSCRIPT). The function make_u_boot_list is defined in helper.mk file. $(eval $(call make_u_boot_list, $(LSTSCRIPT), $(OBJS))) $(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT) $(LSTSCRIPT) - $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(obj) -ansi -D__ASSEMBLY__ -P - <$< >$@ + $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(nandobj)/board/$(BOARDDIR) \ + -ansi -D__ASSEMBLY__ -P - <$< >$@ # create symbolic links for common files diff --git a/nand_spl/board/freescale/mpc8569mds/Makefile b/nand_spl/board/freescale/mpc8569mds/Makefile index c923557..9c77826 100644 --- a/nand_spl/board/freescale/mpc8569mds/Makefile +++ b/nand_spl/board/freescale/mpc8569mds/Makefile @@ -67,7 +67,8 @@ $(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot-nand_spl.lds # $(LDSCRIPT). The function make_u_boot_list is defined in helper.mk file. $(eval $(call make_u_boot_list, $(LSTSCRIPT), $(OBJS))) $(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT) $(LSTSCRIPT) - $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(obj) -ansi -D__ASSEMBLY__ -P - <$< >$@ + $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(nandobj)/board/$(BOARDDIR) \ + -ansi -D__ASSEMBLY__ -P - <$< >$@ # create symbolic links for common files diff --git a/nand_spl/board/freescale/mpc8572ds/Makefile b/nand_spl/board/freescale/mpc8572ds/Makefile index c923557..9c77826 100644 --- a/nand_spl/board/freescale/mpc8572ds/Makefile +++ b/nand_spl/board/freescale/mpc8572ds/Makefile @@ -67,7 +67,8 @@ $(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot-nand_spl.lds # $(LDSCRIPT). The function make_u_boot_list is defined in helper.mk file. $(eval $(call make_u_boot_list, $(LSTSCRIPT), $(OBJS))) $(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT) $(LSTSCRIPT) - $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(obj) -ansi -D__ASSEMBLY__ -P - <$< >$@ + $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(nandobj)/board/$(BOARDDIR) \ + -ansi -D__ASSEMBLY__ -P - <$< >$@ # create symbolic links for common files diff --git a/nand_spl/board/freescale/mx31pdk/Makefile b/nand_spl/board/freescale/mx31pdk/Makefile index 43e72c4..f67ed09 100644 --- a/nand_spl/board/freescale/mx31pdk/Makefile +++ b/nand_spl/board/freescale/mx31pdk/Makefile @@ -42,7 +42,8 @@ $(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds # $(LDSCRIPT). The function make_u_boot_list is defined in helper.mk file. $(eval $(call make_u_boot_list, $(LSTSCRIPT), $(OBJS))) $(nandobj)u-boot.lds: $(LDSCRIPT) $(LSTSCRIPT) - $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(obj) -ansi -D__ASSEMBLY__ -P - <$< >$@ + $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(nandobj)/board/$(BOARDDIR) \ + -ansi -D__ASSEMBLY__ -P - <$< >$@ ######################################################################### diff --git a/nand_spl/board/freescale/p1010rdb/Makefile b/nand_spl/board/freescale/p1010rdb/Makefile index ccff1c7..c3495ec 100644 --- a/nand_spl/board/freescale/p1010rdb/Makefile +++ b/nand_spl/board/freescale/p1010rdb/Makefile @@ -67,7 +67,8 @@ $(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot-nand_spl.lds # $(LDSCRIPT). The function make_u_boot_list is defined in helper.mk file. $(eval $(call make_u_boot_list, $(LSTSCRIPT), $(OBJS))) $(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT) $(LSTSCRIPT) - $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(obj) -ansi -D__ASSEMBLY__ -P - <$< >$@ + $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(nandobj)board/$(BOARDDIR) \ + -ansi -D__ASSEMBLY__ -P - <$< >$@ # create symbolic links for common files diff --git a/nand_spl/board/freescale/p1023rds/Makefile b/nand_spl/board/freescale/p1023rds/Makefile index ffe29c8..9b2c0d7 100644 --- a/nand_spl/board/freescale/p1023rds/Makefile +++ b/nand_spl/board/freescale/p1023rds/Makefile @@ -62,7 +62,8 @@ $(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot-nand_spl.lds # $(LDSCRIPT). The function make_u_boot_list is defined in helper.mk file. $(eval $(call make_u_boot_list, $(LSTSCRIPT), $(OBJS))) $(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT) $(LSTSCRIPT) - $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(obj) -ansi -D__ASSEMBLY__ -P - <$< >$@ + $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(nandobj)/board/$(BOARDDIR) \ + -ansi -D__ASSEMBLY__ -P - <$< >$@ # create symbolic links for common files diff --git a/nand_spl/board/freescale/p1_p2_rdb/Makefile b/nand_spl/board/freescale/p1_p2_rdb/Makefile index c923557..9c77826 100644 --- a/nand_spl/board/freescale/p1_p2_rdb/Makefile +++ b/nand_spl/board/freescale/p1_p2_rdb/Makefile @@ -67,7 +67,8 @@ $(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot-nand_spl.lds # $(LDSCRIPT). The function make_u_boot_list is defined in helper.mk file. $(eval $(call make_u_boot_list, $(LSTSCRIPT), $(OBJS))) $(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT) $(LSTSCRIPT) - $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(obj) -ansi -D__ASSEMBLY__ -P - <$< >$@ + $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(nandobj)/board/$(BOARDDIR) \ + -ansi -D__ASSEMBLY__ -P - <$< >$@ # create symbolic links for common files diff --git a/nand_spl/board/karo/tx25/Makefile b/nand_spl/board/karo/tx25/Makefile index becf7fa..b27189d 100644 --- a/nand_spl/board/karo/tx25/Makefile +++ b/nand_spl/board/karo/tx25/Makefile @@ -63,7 +63,8 @@ $(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds # $(LDSCRIPT). The function make_u_boot_list is defined in helper.mk file. $(eval $(call make_u_boot_list, $(LSTSCRIPT), $(OBJS))) $(nandobj)u-boot.lds: $(LDSCRIPT) $(LSTSCRIPT) - $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(obj) -ansi -D__ASSEMBLY__ -P - <$< >$@ + $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(nandobj)/board/$(BOARDDIR) \ + -ansi -D__ASSEMBLY__ -P - <$< >$@ ######################################################################### -- 1.7.9.5

4 3

[U-Boot] U-Boot NAND-Access
by Peter Niklas 14 Nov '12

14 Nov '12

Hello, We are using a Zynq SoC on a custom Board. We are trying to use a NAND-Flash (MT29F8G08ABABAWP-IT) to store the Xilinx First Stage Boot Loader, U-Boot, Kernel .... We are having trouble to use the NAND-Flash in U-Boot. Currently we are using U-Boot 2012.04.01-00304-g7639205-dirty. and I get the Messag: NAND: No NAND device found!!! nand_scan_ident for NAND failed I enabled CMD_NAND in the specific config file: #define CONFIG_NAND_ZYNQ #define CONFIG_CMD_NAND #define CONFIG_CMD_NAND_LOCK_UNLOCK #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE XPSS_NAND_BASEADDR #define CONFIG_MTD_DEVICE I also tried an older version of U-Boot (U-Boot 2011.03-dirty) before where I got the Output: NAND: No oob scheme defined for oobsize 224 No oob scheme defined for oobsize 224 I also enabled the CMD_NAND as before. When I look into the sources I only see oob_schemes defined for 128. Has anyone tried to use a NAND-flash with the oobsize of 224? Is there some configuration missing? Besides the CMD config, I did not change anything else for NAND-Configuration. Am I missing something? The NAND-Flash has been tested with the Xilinx Drivers and it works. Thanks, Regards, Peter Niklas CONFIDENTIALITY: The contents of this e-mail are confidential and intended only for the above addressee(s). If you are not the intended recipient, or the person responsible for delivering it to the intended recipient, copying or delivering it to anyone else or using it in any unauthorized manner is prohibited and may be unlawful. If you receive this e-mail by mistake, please notify the sender and the systems administrator at straymail(a)tttech.com immediately.

3 4

[U-Boot] [PATCH 1/2] libfdt: Add support for appending the values to a existing property
by Kim Phillips 13 Nov '12

13 Nov '12

From: Minghuan Lian <Minghuan.Lian(a)freescale.com> Some properties may contain multiple values, these values may need to be added to the property respectively. this patch provides this functionality. The main purpose of fdt_append_prop() is to append the values to a existing property, or create a new property if it dose not exist. Signed-off-by: Minghuan Lian <Minghuan.Lian(a)freescale.com> Signed-off-by: David Gibson <david(a)gibson.dropbear.id.au> --- include/libfdt.h | 95 +++++++++++++++++++++++++++++++++++++++++++++++++++++ lib/libfdt/fdt_rw.c | 27 +++++++++++++++ 2 files changed, 122 insertions(+) diff --git a/include/libfdt.h b/include/libfdt.h index de82ed5..78798e8 100644 --- a/include/libfdt.h +++ b/include/libfdt.h @@ -1134,6 +1134,101 @@ static inline int fdt_setprop_cell(void *fdt, int nodeoffset, const char *name, fdt_setprop((fdt), (nodeoffset), (name), (str), strlen(str)+1) /** + * fdt_appendprop - append to or create a property + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to change + * @name: name of the property to append to + * @val: pointer to data to append to the property value + * @len: length of the data to append to the property value + * + * fdt_appendprop() appends the value to the named property in the + * given node, creating the property if it does not already exist. + * + * This function may insert data into the blob, and will therefore + * change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, there is insufficient free space in the blob to + * contain the new property value + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_TRUNCATED, standard meanings + */ +int fdt_appendprop(void *fdt, int nodeoffset, const char *name, + const void *val, int len); + +/** + * fdt_appendprop_cell - append a single cell value to a property + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to change + * @name: name of the property to change + * @val: 32-bit integer value to append to the property (native endian) + * + * fdt_appendprop_cell() appends the given cell value (converting to + * big-endian if necessary) to the value of the named property in the + * given node, or creates a new property with that value if it does + * not already exist. + * + * This function may insert data into the blob, and will therefore + * change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, there is insufficient free space in the blob to + * contain the new property value + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_TRUNCATED, standard meanings + */ +static inline int fdt_appendprop_cell(void *fdt, int nodeoffset, + const char *name, uint32_t val) +{ + val = cpu_to_fdt32(val); + return fdt_appendprop(fdt, nodeoffset, name, &val, sizeof(val)); +} + +/** + * fdt_appendprop_string - append a string to a property + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to change + * @name: name of the property to change + * @str: string value to append to the property + * + * fdt_appendprop_string() appends the given string to the value of + * the named property in the given node, or creates a new property + * with that value if it does not already exist. + * + * This function may insert data into the blob, and will therefore + * change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, there is insufficient free space in the blob to + * contain the new property value + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_TRUNCATED, standard meanings + */ +#define fdt_appendprop_string(fdt, nodeoffset, name, str) \ + fdt_appendprop((fdt), (nodeoffset), (name), (str), strlen(str)+1) + +/** * fdt_delprop - delete a property * @fdt: pointer to the device tree blob * @nodeoffset: offset of the node whose property to nop diff --git a/lib/libfdt/fdt_rw.c b/lib/libfdt/fdt_rw.c index 5c27a67..5ed23d6 100644 --- a/lib/libfdt/fdt_rw.c +++ b/lib/libfdt/fdt_rw.c @@ -293,6 +293,33 @@ int fdt_setprop(void *fdt, int nodeoffset, const char *name, return 0; } +int fdt_appendprop(void *fdt, int nodeoffset, const char *name, + const void *val, int len) +{ + struct fdt_property *prop; + int err, oldlen, newlen; + + FDT_RW_CHECK_HEADER(fdt); + + prop = fdt_get_property_w(fdt, nodeoffset, name, &oldlen); + if (prop) { + newlen = len + oldlen; + err = _fdt_splice_struct(fdt, prop->data, + FDT_TAGALIGN(oldlen), + FDT_TAGALIGN(newlen)); + if (err) + return err; + prop->len = cpu_to_fdt32(newlen); + memcpy(prop->data + oldlen, val, len); + } else { + err = _fdt_add_property(fdt, nodeoffset, name, len, &prop); + if (err) + return err; + memcpy(prop->data, val, len); + } + return 0; +} + int fdt_delprop(void *fdt, int nodeoffset, const char *name) { struct fdt_property *prop; -- 1.7.12

4 8

[U-Boot] [PATCH V2 1/2] mmc: add bcm2835 driver
by Stephen Warren 13 Nov '12

13 Nov '12

This adds a simple driver for the BCM2835's SD controller. Workarounds are implemented for: * Register writes can't be too close to each-other in time, or they will be lost. * Register accesses must all be 32-bit, so implement custom accessors. This code was extracted from: git://github.com/gonzoua/u-boot-pi.git master which was created by Oleksandr Tymoshenko. Portions of the code there were obviously based on the Linux kernel at: git://github.com/raspberrypi/linux.git rpi-3.6.y commit f5b930b "Main bcm2708 linux port" signed-off-by Dom Cobley. swarren changed the following for upstream: * Removed hack udelay()s in bcm2835_sdhci_raw_writel(); setting SDHCI_QUIRK_WAIT_SEND_CMD appears to solve the issues. * Remove register logging from read*/write* functions. * Sort out confusion with min/max_freq values passed to add_sdhci(). * Use more descriptive variable names and calculations in IO accessors. * Simplified and commented twoticks_delay calculation. * checkpatch fixes. Signed-off-by: Oleksandr Tymoshenko <gonzo(a)bluezbox.com> Signed-off-by: Stephen Warren <swarren(a)wwwdotorg.org> --- This series is based on the previous bcm2835 patches I sent, to add the mbox and video drivers. Patch 1 should be independant, but patch 2 depends on those other patches. v2: * Use more descriptive variable names and calculations in IO accessors. * Add Oleksandr's S-o-b. * Rewrite commit description to note that the Linux code this was derived from was S-o-b Dom Cobley. --- arch/arm/include/asm/arch-bcm2835/sdhci.h | 24 ++++ drivers/mmc/Makefile | 1 + drivers/mmc/bcm2835_sdhci.c | 177 +++++++++++++++++++++++++++++ 3 files changed, 202 insertions(+) create mode 100644 arch/arm/include/asm/arch-bcm2835/sdhci.h create mode 100644 drivers/mmc/bcm2835_sdhci.c diff --git a/arch/arm/include/asm/arch-bcm2835/sdhci.h b/arch/arm/include/asm/arch-bcm2835/sdhci.h new file mode 100644 index 0000000..a4f867b --- /dev/null +++ b/arch/arm/include/asm/arch-bcm2835/sdhci.h @@ -0,0 +1,24 @@ +/* + * (C) Copyright 2012 Stephen Warren + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef _BCM2835_SDHCI_H_ +#define _BCM2835_SDHCI_H_ + +#define BCM2835_SDHCI_BASE 0x20300000 + +int bcm2835_sdhci_init(u32 regbase, u32 emmc_freq); + +#endif diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile index a1dd730..6be36f2 100644 --- a/drivers/mmc/Makefile +++ b/drivers/mmc/Makefile @@ -43,6 +43,7 @@ COBJS-$(CONFIG_MXS_MMC) += mxsmmc.o COBJS-$(CONFIG_OMAP_HSMMC) += omap_hsmmc.o COBJS-$(CONFIG_PXA_MMC_GENERIC) += pxa_mmc_gen.o COBJS-$(CONFIG_SDHCI) += sdhci.o +COBJS-$(CONFIG_BCM2835_SDHCI) += bcm2835_sdhci.o COBJS-$(CONFIG_S5P_SDHCI) += s5p_sdhci.o COBJS-$(CONFIG_SH_MMCIF) += sh_mmcif.o COBJS-$(CONFIG_TEGRA_MMC) += tegra_mmc.o diff --git a/drivers/mmc/bcm2835_sdhci.c b/drivers/mmc/bcm2835_sdhci.c new file mode 100644 index 0000000..8f2137e --- /dev/null +++ b/drivers/mmc/bcm2835_sdhci.c @@ -0,0 +1,177 @@ +/* + * This code was extracted from: + * git://github.com/gonzoua/u-boot-pi.git master + * and hence presumably (C) 2012 Oleksandr Tymoshenko + * + * Tweaks for U-Boot upstreaming + * (C) 2012 Stephen Warren + * + * Portions (e.g. read/write macros, concepts for back-to-back register write + * timing workarounds) obviously extracted from the Linux kernel at: + * https://github.com/raspberrypi/linux.git rpi-3.6.y + * + * The Linux kernel code has the following (c) and license, which is hence + * propagated to Oleksandr's tree and here: + * + * Support for SDHCI device on 2835 + * Based on sdhci-bcm2708.c (c) 2010 Broadcom + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +/* Supports: + * SDHCI platform device - Arasan SD controller in BCM2708 + * + * Inspired by sdhci-pci.c, by Pierre Ossman + */ + +#include <common.h> +#include <malloc.h> +#include <sdhci.h> + +/* 400KHz is max freq for card ID etc. Use that as min */ +#define MIN_FREQ 400000 + +static uint twoticks_delay; + +static inline void bcm2835_sdhci_raw_writel(struct sdhci_host *host, u32 val, + int reg) +{ + static ulong last_write; + + /* + * The Arasan has a bugette whereby it may lose the content of + * successive writes to registers that are within two SD-card clock + * cycles of each other (a clock domain crossing problem). + * It seems, however, that the data register does not have this problem. + * (Which is just as well - otherwise we'd have to nobble the DMA engine + * too) + */ + while (get_timer(last_write) < twoticks_delay) + ; + + writel(val, host->ioaddr + reg); + last_write = get_timer(0); +} + +static inline u32 bcm2835_sdhci_raw_readl(struct sdhci_host *host, int reg) +{ + return readl(host->ioaddr + reg); +} + +static void bcm2835_sdhci_writel(struct sdhci_host *host, u32 val, int reg) +{ + bcm2835_sdhci_raw_writel(host, val, reg); +} + +static void bcm2835_sdhci_writew(struct sdhci_host *host, u16 val, int reg) +{ + static u32 shadow; + u32 oldval = (reg == SDHCI_COMMAND) ? shadow : + bcm2835_sdhci_raw_readl(host, reg & ~3); + u32 word_num = (reg >> 1) & 1; + u32 word_shift = word_num * 16; + u32 mask = 0xffff << word_shift; + u32 newval = (oldval & ~mask) | (val << word_shift); + + if (reg == SDHCI_TRANSFER_MODE) + shadow = newval; + else + bcm2835_sdhci_raw_writel(host, newval, reg & ~3); +} + +static void bcm2835_sdhci_writeb(struct sdhci_host *host, u8 val, int reg) +{ + u32 oldval = bcm2835_sdhci_raw_readl(host, reg & ~3); + u32 byte_num = reg & 3; + u32 byte_shift = byte_num * 8; + u32 mask = 0xff << byte_shift; + u32 newval = (oldval & ~mask) | (val << byte_shift); + + bcm2835_sdhci_raw_writel(host, newval, reg & ~3); +} + +static u32 bcm2835_sdhci_readl(struct sdhci_host *host, int reg) +{ + u32 val = bcm2835_sdhci_raw_readl(host, reg); + + return val; +} + +static u16 bcm2835_sdhci_readw(struct sdhci_host *host, int reg) +{ + u32 val = bcm2835_sdhci_raw_readl(host, (reg & ~3)); + u32 word_num = (reg >> 1) & 1; + u32 word_shift = word_num * 16; + u32 word = (val >> word_shift) & 0xffff; + + return word; +} + +static u8 bcm2835_sdhci_readb(struct sdhci_host *host, int reg) +{ + u32 val = bcm2835_sdhci_raw_readl(host, (reg & ~3)); + u32 byte_num = reg & 3; + u32 byte_shift = byte_num * 8; + u32 byte = (val >> byte_shift) & 0xff; + + return byte; +} + +static const struct sdhci_ops bcm2835_ops = { + .write_l = bcm2835_sdhci_writel, + .write_w = bcm2835_sdhci_writew, + .write_b = bcm2835_sdhci_writeb, + .read_l = bcm2835_sdhci_readl, + .read_w = bcm2835_sdhci_readw, + .read_b = bcm2835_sdhci_readb, +}; + +int bcm2835_sdhci_init(u32 regbase, u32 emmc_freq) +{ + struct sdhci_host *host = NULL; + + /* + * See the comments in bcm2835_sdhci_raw_writel(). + * + * This should probably be dynamically calculated based on the actual + * frequency. However, this is the longest we'll have to wait, and + * doesn't seem to slow access down too much, so the added complexity + * doesn't seem worth it for now. + * + * 1/MIN_FREQ is (max) time per tick of eMMC clock. + * 2/MIN_FREQ is time for two ticks. + * Multiply by 1000000 to get uS per two ticks. + * +1 for hack rounding. + */ + twoticks_delay = ((2 * 1000000) / MIN_FREQ) + 1; + + host = malloc(sizeof(struct sdhci_host)); + if (!host) { + printf("sdhci_host malloc fail!\n"); + return 1; + } + + host->name = "bcm2835_sdhci"; + host->ioaddr = (void *)regbase; + host->quirks = SDHCI_QUIRK_BROKEN_VOLTAGE | SDHCI_QUIRK_BROKEN_R1B | + SDHCI_QUIRK_WAIT_SEND_CMD; + host->voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195; + host->ops = &bcm2835_ops; + + host->version = sdhci_readw(host, SDHCI_HOST_VERSION); + add_sdhci(host, emmc_freq, MIN_FREQ); + + return 0; +} -- 1.7.9.5

2 4