May 2010 - U-Boot

[U-Boot] [PATCH 0/3] Add support for MB86R0x SoCs
by Matthias Weisser 12 Jun '10

12 Jun '10

This patchset adds support for MB86R0x SoC familiy from Fujitsu, its built in lcd controller and a first board using the MB86R01. Matthias Weisser (3): arm: Add support for MB86R0x SoCs video: add support for display controller in MB86R0x SoCs arm: Add support for jadecpu board based on MB86R01 SoC MAINTAINERS | 4 + MAKEALL | 1 + Makefile | 3 + arch/arm/cpu/arm926ejs/mb86r0x/Makefile | 47 +++++ arch/arm/cpu/arm926ejs/mb86r0x/reset.c | 37 ++++ arch/arm/cpu/arm926ejs/mb86r0x/timer.c | 129 ++++++++++++ arch/arm/include/asm/arch-mb86r0x/hardware.h | 31 +++ arch/arm/include/asm/arch-mb86r0x/mb86r0x.h | 170 ++++++++++++++++ board/syteco/jadecpu/Makefile | 55 +++++ board/syteco/jadecpu/config.mk | 1 + board/syteco/jadecpu/jadecpu.c | 198 ++++++++++++++++++ board/syteco/jadecpu/lowlevel_init.S | 279 ++++++++++++++++++++++++++ common/serial.c | 3 +- drivers/video/Makefile | 1 + drivers/video/cfb_console.c | 8 + drivers/video/mb86r0xgdc.c | 194 ++++++++++++++++++ include/configs/jadecpu.h | 189 +++++++++++++++++ include/serial.h | 3 +- tools/Makefile | 3 + tools/logos/syteco.bmp | Bin 0 -> 11414 bytes 20 files changed, 1354 insertions(+), 2 deletions(-) create mode 100644 arch/arm/cpu/arm926ejs/mb86r0x/Makefile create mode 100644 arch/arm/cpu/arm926ejs/mb86r0x/reset.c create mode 100644 arch/arm/cpu/arm926ejs/mb86r0x/timer.c create mode 100644 arch/arm/include/asm/arch-mb86r0x/hardware.h create mode 100644 arch/arm/include/asm/arch-mb86r0x/mb86r0x.h create mode 100644 board/syteco/jadecpu/Makefile create mode 100644 board/syteco/jadecpu/config.mk create mode 100644 board/syteco/jadecpu/jadecpu.c create mode 100644 board/syteco/jadecpu/lowlevel_init.S create mode 100644 drivers/video/mb86r0xgdc.c create mode 100644 include/configs/jadecpu.h create mode 100644 tools/logos/syteco.bmp

4 21

[U-Boot] [PATCH] arm: add initilisation of watchdog in init_sequence
by Nicolas Ferre 10 Jun '10

10 Jun '10

For platforms that implement a hardware watchdog, call its initialization routine in init_sequence. This location has been chosen to be the closest to initialization of console as some watchdog drivers are writing status messages. On the other hand, watchdog setup should be close to chip startup to be able to begin the triggering quickly. Signed-off-by: Nicolas Ferre <nicolas.ferre(a)atmel.com> --- arch/arm/lib/board.c | 7 +++++++ 1 files changed, 7 insertions(+), 0 deletions(-) diff --git a/arch/arm/lib/board.c b/arch/arm/lib/board.c index f5660a9..569009e 100644 --- a/arch/arm/lib/board.c +++ b/arch/arm/lib/board.c @@ -70,6 +70,10 @@ extern int AT91F_DataflashInit(void); extern void dataflash_print_info(void); #endif +#ifdef CONFIG_HW_WATCHDOG +extern void hw_watchdog_init(void); +#endif + #ifndef CONFIG_IDENT_STRING #define CONFIG_IDENT_STRING "" #endif @@ -251,6 +255,9 @@ init_fnc_t *init_sequence[] = { serial_init, /* serial communications setup */ console_init_f, /* stage 1 init of console */ display_banner, /* say that we are here */ +#if defined(CONFIG_HW_WATCHDOG) + hw_watchdog_init, /* watchdog setup */ +#endif #if defined(CONFIG_DISPLAY_CPUINFO) print_cpuinfo, /* display cpu info (and speed) */ #endif -- 1.5.6.5

2 2

[U-Boot] [PATCH] nios2: add gpio based status led driver
by Thomas Chou 09 Jun '10

09 Jun '10

This patch adds a gpio based status led driver. The led mask is used to specify the gpio pin. Signed-off-by: Thomas Chou <thomas(a)wytron.com.tw> --- board/altera/common/gpioled.c | 30 ++++++++++++++++++++++++++++++ 1 files changed, 30 insertions(+), 0 deletions(-) create mode 100644 board/altera/common/gpioled.c diff --git a/board/altera/common/gpioled.c b/board/altera/common/gpioled.c new file mode 100644 index 0000000..9a51fae --- /dev/null +++ b/board/altera/common/gpioled.c @@ -0,0 +1,30 @@ +/* + * Status LED driver based on gpio + * + * Copyright (C) 2010 Thomas Chou <thomas(a)wytron.com.tw> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <common.h> +#include <status_led.h> +#include <asm/gpio.h> + +/* assume led is active low */ + +void __led_init(led_id_t mask, int state) +{ + gpio_direction_output(mask, (state == STATUS_LED_ON) ? 0 : 1); +} + +void __led_set(led_id_t mask, int state) +{ + gpio_set_value(mask, (state == STATUS_LED_ON) ? 0 : 1); +} + +void __led_toggle(led_id_t mask) +{ + gpio_set_value(mask, !gpio_get_value (mask)); +} -- 1.6.6.1

5 48

[U-Boot] [PATCH] logbuff: Prevent an infinite loop for console output
by Peter Tyser 08 Jun '10

08 Jun '10

When using 'logbuff' as stdout and the console loglevel is greater than a message's loglevel it is supposed to be both logged, and printed to the console. The logbuff_printk() function is responsible for both logging and displaying the message. However, logbuff_printk() previously used printf() to print the message to the console. The printf() call would eventually end up back in logbuff_printk(), and an infinite loop would occur which would hang a board. Using serial_puts() instead of printf() in logbuff_printk() avoids the recursion and resolves the issue. Signed-off-by: Peter Tyser <ptyser(a)xes-inc.com> Reported-by: Dennis Ruffer <daruffer(a)gmail.com> --- common/cmd_log.c | 7 ++++--- 1 files changed, 4 insertions(+), 3 deletions(-) diff --git a/common/cmd_log.c b/common/cmd_log.c index e3ebe96..baffeb1 100644 --- a/common/cmd_log.c +++ b/common/cmd_log.c @@ -313,9 +313,10 @@ static int logbuff_printk(const char *line) break; } } - if (msg_level < console_loglevel) { - printf("%s", msg); - } + + if (msg_level < console_loglevel) + serial_puts(msg); + if (line_feed) msg_level = -1; } -- 1.6.2.1

3 4

[U-Boot] [PATCH] OMAP3: pandora: enable battery backup capacitor
by Grazvydas Ignotas 08 Jun '10

08 Jun '10

Pandora has a capacitor connected as backup battery, which allows retaining RTC for some time while main battery is removed. Enable backup battery charge function to charge that capacitor. Signed-off-by: Grazvydas Ignotas <notasas(a)gmail.com> --- board/pandora/pandora.c | 9 +++++++++ 1 files changed, 9 insertions(+), 0 deletions(-) diff --git a/board/pandora/pandora.c b/board/pandora/pandora.c index 75e4330..355e9ea 100644 --- a/board/pandora/pandora.c +++ b/board/pandora/pandora.c @@ -37,6 +37,10 @@ #include <asm/mach-types.h> #include "pandora.h" +#define TWL4030_BB_CFG_BBCHEN (1 << 4) +#define TWL4030_BB_CFG_BBSEL_3200MV (3 << 2) +#define TWL4030_BB_CFG_BBISEL_500UA 2 + /* * Routine: board_init * Description: Early hardware init. @@ -78,6 +82,11 @@ int misc_init_r(void) writel(GPIO28, &gpio5_base->setdataout); writel(GPIO4, &gpio6_base->setdataout); + /* Enable battery backup capacitor (3.2V, 0.5mA charge current) */ + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_BB_CFG_BBCHEN | TWL4030_BB_CFG_BBSEL_3200MV | + TWL4030_BB_CFG_BBISEL_500UA, TWL4030_PM_RECEIVER_BB_CFG); + dieid_num_r(); return 0; -- 1.6.3.3

2 2

[U-Boot] [PATCH 0/2] arm: Adding support for TI OMAP4430 SDP
by Aneesh V 08 Jun '10

08 Jun '10

The following series implements support for TI OMAP4430 SDP based TI OMAP4430. TI OMAP4430 is a Cortex-A9 based SOC from TI. OMAP4430 is a refrence board based on OMAP4430. The first patch in this series renames the cpu arm_cortexa8 to armv7 so that the existing cortexa8 code can be shared with cortexa9. Both A8 and A9 are based on armv7 architecture. The second patch adds minimal support for OMAP4430 SDP. With this patch OMAP4430 SDP boots up. Other features such as MMC, ethernet etc will be added in subsequent patches. Aneesh V (2): arm: renaming the cpu arm_cortexa8 to armv7 arm: cortexa9: adding support for TI OMAP4430 SDP Makefile | 28 ++- arch/arm/cpu/{arm_cortexa8 => armv7}/Makefile | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/config.mk | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/cpu.c | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/Makefile | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/clock.c | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/iomux.c | 0 .../{arm_cortexa8 => armv7}/mx51/lowlevel_init.S | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/soc.c | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/speed.c | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/timer.c | 0 .../cpu/{arm_cortexa8 => armv7}/mx51/u-boot.lds | 0 .../arm/cpu/{arm_cortexa8 => armv7}/omap3/Makefile | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/board.c | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/cache.S | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/clock.c | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/gpio.c | 0 .../{arm_cortexa8 => armv7}/omap3/lowlevel_init.S | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/mem.c | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/reset.S | 0 .../cpu/{arm_cortexa8 => armv7}/omap3/sys_info.c | 0 .../arm/cpu/{arm_cortexa8 => armv7}/omap3/syslib.c | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/timer.c | 0 .../{arm_cortexa8/omap3 => armv7/omap4}/Makefile | 7 +- .../{arm_cortexa8/s5pc1xx => armv7/omap4}/cache.S | 66 +++-- .../mx51/speed.c => armv7/omap4/lowlevel_init.S} | 40 ++- arch/arm/cpu/armv7/omap4/omap4.c | 97 +++++++ .../{arm_cortexa8/omap3 => armv7/omap4}/reset.S | 0 .../s5pc1xx/cpu_info.c => armv7/omap4/sys_info.c} | 51 ++-- .../{arm_cortexa8/omap3 => armv7/omap4}/timer.c | 48 ++-- .../cpu/{arm_cortexa8 => armv7}/s5pc1xx/Makefile | 0 .../cpu/{arm_cortexa8 => armv7}/s5pc1xx/cache.S | 0 .../cpu/{arm_cortexa8 => armv7}/s5pc1xx/clock.c | 0 .../cpu/{arm_cortexa8 => armv7}/s5pc1xx/cpu_info.c | 0 .../cpu/{arm_cortexa8 => armv7}/s5pc1xx/reset.S | 0 .../cpu/{arm_cortexa8 => armv7}/s5pc1xx/sromc.c | 0 .../cpu/{arm_cortexa8 => armv7}/s5pc1xx/timer.c | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/start.S | 0 arch/arm/cpu/{arm_cortexa8 => armv7}/u-boot.lds | 2 +- arch/arm/include/asm/arch-omap4/cpu.h | 89 ++++++ arch/arm/include/asm/arch-omap4/omap4.h | 142 ++++++++++ .../reset.S => include/asm/arch-omap4/sys_proto.h} | 38 ++-- .../cpu/arm_cortexa8 => board/ti/sdp4430}/Makefile | 24 +- .../arm_cortexa8 => board/ti/sdp4430}/config.mk | 25 +- .../s5pc1xx/reset.S => board/ti/sdp4430/sdp.c | 57 +++-- include/configs/omap4_sdp4430.h | 280 ++++++++++++++++++++ 46 files changed, 817 insertions(+), 177 deletions(-) copy arch/arm/cpu/{arm_cortexa8 => armv7}/Makefile (100%) copy arch/arm/cpu/{arm_cortexa8 => armv7}/config.mk (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/cpu.c (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/Makefile (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/clock.c (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/iomux.c (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/lowlevel_init.S (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/soc.c (100%) copy arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/speed.c (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/timer.c (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/mx51/u-boot.lds (100%) copy arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/Makefile (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/board.c (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/cache.S (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/clock.c (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/gpio.c (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/lowlevel_init.S (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/mem.c (100%) copy arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/reset.S (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/sys_info.c (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/syslib.c (100%) copy arch/arm/cpu/{arm_cortexa8 => armv7}/omap3/timer.c (100%) rename arch/arm/cpu/{arm_cortexa8/omap3 => armv7/omap4}/Makefile (93%) copy arch/arm/cpu/{arm_cortexa8/s5pc1xx => armv7/omap4}/cache.S (73%) rename arch/arm/cpu/{arm_cortexa8/mx51/speed.c => armv7/omap4/lowlevel_init.S} (63%) create mode 100644 arch/arm/cpu/armv7/omap4/omap4.c copy arch/arm/cpu/{arm_cortexa8/omap3 => armv7/omap4}/reset.S (100%) copy arch/arm/cpu/{arm_cortexa8/s5pc1xx/cpu_info.c => armv7/omap4/sys_info.c} (51%) rename arch/arm/cpu/{arm_cortexa8/omap3 => armv7/omap4}/timer.c (73%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/s5pc1xx/Makefile (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/s5pc1xx/cache.S (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/s5pc1xx/clock.c (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/s5pc1xx/cpu_info.c (100%) copy arch/arm/cpu/{arm_cortexa8 => armv7}/s5pc1xx/reset.S (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/s5pc1xx/sromc.c (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/s5pc1xx/timer.c (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/start.S (100%) rename arch/arm/cpu/{arm_cortexa8 => armv7}/u-boot.lds (97%) create mode 100644 arch/arm/include/asm/arch-omap4/cpu.h create mode 100644 arch/arm/include/asm/arch-omap4/omap4.h rename arch/arm/{cpu/arm_cortexa8/omap3/reset.S => include/asm/arch-omap4/sys_proto.h} (58%) rename {arch/arm/cpu/arm_cortexa8 => board/ti/sdp4430}/Makefile (79%) rename {arch/arm/cpu/arm_cortexa8 => board/ti/sdp4430}/config.mk (54%) rename arch/arm/cpu/arm_cortexa8/s5pc1xx/reset.S => board/ti/sdp4430/sdp.c (58%) create mode 100644 include/configs/omap4_sdp4430.h

6 8

[U-Boot] [PATCH v6 0/3] TI: tnetv107x patch series
by Cyril Chemparathy 07 Jun '10

07 Jun '10

TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a bunch on on-chip integrated peripherals. This patch series generalizes current ARM1176 code to allow for the addition of new ARM1176 SOCs. The remaining patches in this series add arch and board support. Cyril Chemparathy (3): ARM1176: Coexist with other ARM1176 platforms ARM1176: TI: TNETV107X soc initial support TI: TNETV107X EVM initial support MAINTAINERS | 4 + MAKEALL | 1 + Makefile | 3 + arch/arm/cpu/arm1176/cpu.c | 3 - arch/arm/cpu/arm1176/start.S | 65 +++- arch/arm/cpu/arm1176/tnetv107x/Makefile | 44 +++ arch/arm/cpu/arm1176/tnetv107x/aemif.c | 93 +++++ arch/arm/cpu/arm1176/tnetv107x/clock.c | 451 +++++++++++++++++++++++ arch/arm/cpu/arm1176/tnetv107x/init.c | 37 ++ arch/arm/cpu/arm1176/tnetv107x/lowlevel_init.S | 25 ++ arch/arm/cpu/arm1176/tnetv107x/mux.c | 334 +++++++++++++++++ arch/arm/cpu/arm1176/tnetv107x/timer.c | 122 ++++++ arch/arm/cpu/arm1176/tnetv107x/wdt.c | 180 +++++++++ arch/arm/include/asm/arch-tnetv107x/clock.h | 68 ++++ arch/arm/include/asm/arch-tnetv107x/emif_defs.h | 1 + arch/arm/include/asm/arch-tnetv107x/hardware.h | 173 +++++++++ arch/arm/include/asm/arch-tnetv107x/mux.h | 306 +++++++++++++++ arch/arm/include/asm/arch-tnetv107x/nand_defs.h | 38 ++ board/ti/tnetv107xevm/Makefile | 49 +++ board/ti/tnetv107xevm/config.mk | 20 + board/ti/tnetv107xevm/sdb_board.c | 149 ++++++++ include/configs/smdk6400.h | 8 +- include/configs/tnetv107x_evm.h | 153 ++++++++ 23 files changed, 2304 insertions(+), 23 deletions(-) create mode 100644 arch/arm/cpu/arm1176/tnetv107x/Makefile create mode 100644 arch/arm/cpu/arm1176/tnetv107x/aemif.c create mode 100644 arch/arm/cpu/arm1176/tnetv107x/clock.c create mode 100644 arch/arm/cpu/arm1176/tnetv107x/init.c create mode 100644 arch/arm/cpu/arm1176/tnetv107x/lowlevel_init.S create mode 100644 arch/arm/cpu/arm1176/tnetv107x/mux.c create mode 100644 arch/arm/cpu/arm1176/tnetv107x/timer.c create mode 100644 arch/arm/cpu/arm1176/tnetv107x/wdt.c create mode 100644 arch/arm/include/asm/arch-tnetv107x/clock.h create mode 100644 arch/arm/include/asm/arch-tnetv107x/emif_defs.h create mode 100644 arch/arm/include/asm/arch-tnetv107x/hardware.h create mode 100644 arch/arm/include/asm/arch-tnetv107x/mux.h create mode 100644 arch/arm/include/asm/arch-tnetv107x/nand_defs.h create mode 100644 board/ti/tnetv107xevm/Makefile create mode 100644 board/ti/tnetv107xevm/config.mk create mode 100644 board/ti/tnetv107xevm/sdb_board.c create mode 100644 include/configs/tnetv107x_evm.h

2 5

[U-Boot] [PATCH-V3 1/2] AM35x: Add support for AM3517EVM
by hvaibhav＠ti.com 07 Jun '10

07 Jun '10

From: Vaibhav Hiremath <hvaibhav(a)ti.com> This patch adds basic support for the AM3517EVM. It includes: - Board int file (.c and .h) - Default configuration file - Updates for Makefile Changes from V2: - Removed trailing spaces - Updated MAINTAINERS & MAKEALL for am3517_evm Signed-off-by: Vaibhav Hiremath <hvaibhav(a)ti.com> Signed-off-by: Sanjeev Premi <premi(a)ti.com> --- MAINTAINERS | 4 + MAKEALL | 1 + Makefile | 3 + arch/arm/include/asm/arch-omap3/mux.h | 38 +++- board/logicpd/am3517evm/Makefile | 46 ++++ board/logicpd/am3517evm/am3517evm.c | 76 ++++++ board/logicpd/am3517evm/am3517evm.h | 405 +++++++++++++++++++++++++++++++++ board/logicpd/am3517evm/config.mk | 30 +++ include/configs/am3517_evm.h | 296 ++++++++++++++++++++++++ 9 files changed, 898 insertions(+), 1 deletions(-) create mode 100644 board/logicpd/am3517evm/Makefile create mode 100644 board/logicpd/am3517evm/am3517evm.c create mode 100644 board/logicpd/am3517evm/am3517evm.h create mode 100644 board/logicpd/am3517evm/config.mk create mode 100644 include/configs/am3517_evm.h diff --git a/MAINTAINERS b/MAINTAINERS index 5cbc845..0bc65e1 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -798,6 +798,10 @@ Alex Z lart SA1100 dnp1110 SA1110 +Vaibhav Hiremath <hvaibhav(a)ti.com> + + am3517_evm ARM CORTEX-A8 (AM35x SoC) + ------------------------------------------------------------------------- Unknown / orphaned boards: diff --git a/MAKEALL b/MAKEALL index bb09627..cd59daa 100755 --- a/MAKEALL +++ b/MAKEALL @@ -641,6 +641,7 @@ LIST_ARM11=" \ ## ARM Cortex-A8 Systems ######################################################################### LIST_ARM_CORTEX_A8=" \ + am3517_evm \ devkit8000 \ mx51evk \ omap3_beagle \ diff --git a/Makefile b/Makefile index 2d96574..57b3491 100644 --- a/Makefile +++ b/Makefile @@ -3155,6 +3155,9 @@ SMN42_config : unconfig ## ARM CORTEX Systems ######################################################################### +am3517_evm_config : unconfig + @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 am3517evm logicpd omap3 + devkit8000_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 devkit8000 timll omap3 diff --git a/arch/arm/include/asm/arch-omap3/mux.h b/arch/arm/include/asm/arch-omap3/mux.h index 0c01c73..ffeb982 100644 --- a/arch/arm/include/asm/arch-omap3/mux.h +++ b/arch/arm/include/asm/arch-omap3/mux.h @@ -283,7 +283,7 @@ /*Control and debug */ #define CONTROL_PADCONF_SYS_32K 0x0A04 #define CONTROL_PADCONF_SYS_CLKREQ 0x0A06 -#define CONTROL_PADCONF_SYS_NIRQ 0x01E0 +#define CONTROL_PADCONF_SYS_NRESWARM 0x0A08 #define CONTROL_PADCONF_SYS_BOOT0 0x0A0A #define CONTROL_PADCONF_SYS_BOOT1 0x0A0C #define CONTROL_PADCONF_SYS_BOOT2 0x0A0E @@ -337,6 +337,7 @@ #define CONTROL_PADCONF_ETK_D14_ES2 0x05F8 #define CONTROL_PADCONF_ETK_D15_ES2 0x05FA /*Die to Die */ +#define CONTROL_PADCONF_SYS_NIRQ 0x01E0 #define CONTROL_PADCONF_D2D_MCAD0 0x01E4 #define CONTROL_PADCONF_D2D_MCAD1 0x01E6 #define CONTROL_PADCONF_D2D_MCAD2 0x01E8 @@ -403,6 +404,41 @@ #define CONTROL_PADCONF_D2D_SBUSFLAG 0x0260 #define CONTROL_PADCONF_SDRC_CKE0 0x0262 #define CONTROL_PADCONF_SDRC_CKE1 0x0264 +/* AM3517 specific */ +#define CONTROL_PADCONF_CCDC_PCLK 0x01E4 +#define CONTROL_PADCONF_CCDC_FIELD 0x01E6 +#define CONTROL_PADCONF_CCDC_HD 0x01E8 +#define CONTROL_PADCONF_CCDC_VD 0x01EA +#define CONTROL_PADCONF_CCDC_WEN 0x01EC +#define CONTROL_PADCONF_CCDC_DATA0 0x01EE +#define CONTROL_PADCONF_CCDC_DATA1 0x01F0 +#define CONTROL_PADCONF_CCDC_DATA2 0x01F2 +#define CONTROL_PADCONF_CCDC_DATA3 0x01F4 +#define CONTROL_PADCONF_CCDC_DATA4 0x01F6 +#define CONTROL_PADCONF_CCDC_DATA5 0x01F8 +#define CONTROL_PADCONF_CCDC_DATA6 0x01FA +#define CONTROL_PADCONF_CCDC_DATA7 0x01FC +#define CONTROL_PADCONF_RMII_MDIO_DATA 0x01FE +#define CONTROL_PADCONF_RMII_MDIO_CLK 0x0200 +#define CONTROL_PADCONF_RMII_RXD0 0x0202 +#define CONTROL_PADCONF_RMII_RXD1 0x0204 +#define CONTROL_PADCONF_RMII_CRS_DV 0x0206 +#define CONTROL_PADCONF_RMII_RXER 0x0208 +#define CONTROL_PADCONF_RMII_TXD0 0x020A +#define CONTROL_PADCONF_RMII_TXD1 0x020C +#define CONTROL_PADCONF_RMII_TXEN 0x020E +#define CONTROL_PADCONF_RMII_50MHZ_CLK 0x0210 +#define CONTROL_PADCONF_USB0_DRVBUS 0x0212 +#define CONTROL_PADCONF_HECC1_TXD 0x0214 +#define CONTROL_PADCONF_HECC1_RXD 0x0216 +#define CONTROL_PADCONF_SYS_BOOT7 0x0218 +#define CONTROL_PADCONF_SDRC_DQS0N 0x021A +#define CONTROL_PADCONF_SDRC_DQS1N 0x021C +#define CONTROL_PADCONF_SDRC_DQS2N 0x021E +#define CONTROL_PADCONF_SDRC_DQS3N 0x0220 +#define CONTROL_PADCONF_STRBEN_DLY0 0x0222 +#define CONTROL_PADCONF_STRBEN_DLY1 0x0224 +#define CONTROL_PADCONF_SYS_BOOT8 0x0226 #define MUX_VAL(OFFSET,VALUE)\ writew((VALUE), OMAP34XX_CTRL_BASE + (OFFSET)); diff --git a/board/logicpd/am3517evm/Makefile b/board/logicpd/am3517evm/Makefile new file mode 100644 index 0000000..3a6b1a1 --- /dev/null +++ b/board/logicpd/am3517evm/Makefile @@ -0,0 +1,46 @@ +# +# Author: Vaibhav Hiremath <hvaibhav(a)ti.com> +# +# Based on ti/evm/Makefile +# +# Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ +# +# This program is free software; you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation; either version 2 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := am3517evm.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend diff --git a/board/logicpd/am3517evm/am3517evm.c b/board/logicpd/am3517evm/am3517evm.c new file mode 100644 index 0000000..2b912a9 --- /dev/null +++ b/board/logicpd/am3517evm/am3517evm.c @@ -0,0 +1,76 @@ +/* + * am3517evm.c - board file for TI's AM3517 family of devices. + * + * Author: Vaibhav Hiremath <hvaibhav(a)ti.com> + * + * Based on ti/evm/evm.c + * + * Copyright (C) 2010 + * Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/mem.h> +#include <asm/arch/mux.h> +#include <asm/arch/sys_proto.h> +#include <asm/mach-types.h> +#include <i2c.h> +#include "am3517evm.h" + +/* + * Routine: board_init + * Description: Early hardware init. + */ +int board_init(void) +{ + DECLARE_GLOBAL_DATA_PTR; + + gpmc_init(); /* in SRAM or SDRAM, finish GPMC */ + /* board id for Linux */ + gd->bd->bi_arch_number = MACH_TYPE_OMAP3517EVM; + /* boot param addr */ + gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100); + + return 0; +} + +/* + * Routine: misc_init_r + * Description: Init i2c, ethernet, etc... (done here so udelay works) + */ +int misc_init_r(void) +{ +#ifdef CONFIG_DRIVER_OMAP34XX_I2C + i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +#endif + + dieid_num_r(); + + return 0; +} + +/* + * Routine: set_muxconf_regs + * Description: Setting up the configuration Mux registers specific to the + * hardware. Many pins need to be moved from protect to primary + * mode. + */ +void set_muxconf_regs(void) +{ + MUX_AM3517EVM(); +} diff --git a/board/logicpd/am3517evm/am3517evm.h b/board/logicpd/am3517evm/am3517evm.h new file mode 100644 index 0000000..68d746c --- /dev/null +++ b/board/logicpd/am3517evm/am3517evm.h @@ -0,0 +1,405 @@ +/* + * am3517evm.h - Header file for the AM3517 EVM. + * + * Author: Vaibhav Hiremath <hvaibhav(a)ti.com> + * + * Based on ti/evm/evm.h + * + * Copyright (C) 2010 + * Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef _AM3517EVM_H_ +#define _AM3517EVM_H_ + +const omap3_sysinfo sysinfo = { + DDR_DISCRETE, + "AM3517EVM Board", + "NAND", +}; + +/* + * IEN - Input Enable + * IDIS - Input Disable + * PTD - Pull type Down + * PTU - Pull type Up + * DIS - Pull type selection is inactive + * EN - Pull type selection is active + * M0 - Mode 0 + * The commented string gives the final mux configuration for that pin + */ +#define MUX_AM3517EVM() \ + /* SDRC */\ + MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_DQS0N), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(SDRC_DQS1N), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(SDRC_DQS2N), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(SDRC_DQS3N), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(SDRC_CKE0), (M0)) \ + MUX_VAL(CP(SDRC_CKE1), (M0)) \ + /*sdrc_strben_dly0*/\ + MUX_VAL(CP(STRBEN_DLY0), (IEN | PTD | EN | M0)) \ + /*sdrc_strben_dly1*/\ + MUX_VAL(CP(STRBEN_DLY1), (IEN | PTD | EN | M0)) \ + /* GPMC */\ + MUX_VAL(CP(GPMC_A1), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A2), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A3), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A4), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A5), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A6), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A7), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A8), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A9), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A10), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D0), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D1), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D2), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D3), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D4), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D5), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D6), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D7), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D8), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D9), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D10), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D11), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D12), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D13), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D14), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D15), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NCS4), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NCS5), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_CLK), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NBE1), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M4)) /*GPIO_64*/\ + /* - ETH_nRESET*/\ + MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) \ + /* DSS */\ + MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) \ + /* CAMERA */\ + MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CAM_XCLKA), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CAM_FLD), (IDIS | PTD | DIS | M4)) /*GPIO_98*/\ + /* - CAM_RESET*/\ + MUX_VAL(CP(CAM_D0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D3), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D4), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D5), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D6), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D7), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D8), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D9), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D10), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D11), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_XCLKB), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_WEN), (IEN | PTD | DIS | M4)) /*GPIO_167*/\ + MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CSI2_DY1), (IEN | PTD | DIS | M0)) \ + /* MMC */\ + MUX_VAL(CP(MMC1_CLK), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(MMC1_CMD), (IEN | PTU | DIS | M0)) \ + MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | DIS | M0)) \ + MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | DIS | M0)) \ + MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | DIS | M0)) \ + MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | DIS | M0)) \ + /* WriteProtect */\ + MUX_VAL(CP(MMC1_DAT4), (IEN | PTU | EN | M4)) \ + MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M4)) /*CardDetect*/\ + MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M4)) \ + MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M4)) \ + \ + MUX_VAL(CP(MMC2_CLK), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(MMC2_CMD), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MMC2_DAT0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MMC2_DAT1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MMC2_DAT2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MMC2_DAT3), (IEN | PTD | DIS | M0)) \ + /* McBSP */\ + MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) \ + MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(MCBSP1_DX), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP1_DR), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP1_FSX), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTD | DIS | M0)) \ + \ + MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP2_DR), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0)) \ + \ + MUX_VAL(CP(MCBSP3_DX), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP3_DR), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP3_FSX), (IEN | PTD | DIS | M0)) \ + \ + MUX_VAL(CP(MCBSP4_CLKX), (IDIS | PTD | DIS | M4)) /*GPIO_152*/\ + /* - LCD_INI*/\ + MUX_VAL(CP(MCBSP4_DR), (IDIS | PTD | DIS | M4)) /*GPIO_153*/\ + /* - LCD_ENVDD */\ + MUX_VAL(CP(MCBSP4_DX), (IDIS | PTD | DIS | M4)) /*GPIO_154*/\ + /* - LCD_QVGA/nVGA */\ + MUX_VAL(CP(MCBSP4_FSX), (IDIS | PTD | DIS | M4)) /*GPIO_155*/\ + /* - LCD_RESB */\ + /* UART */\ + MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(UART1_CTS), (IEN | PTU | DIS | M0)) \ + \ + MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M0)) \ + \ + MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTU | DIS | M0)) \ + MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) \ + /* I2C */\ + MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) \ + /* McSPI */\ + MUX_VAL(CP(MCSPI1_CLK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(MCSPI1_CS1), (IEN | PTD | EN | M4)) /*GPIO_175*/\ + MUX_VAL(CP(MCSPI1_CS2), (IEN | PTU | DIS | M4)) /*GPIO_176*/\ + /* - LAN_INTR*/\ + MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | EN | M0)) \ + \ + MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M4)) \ + MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M4)) \ + /* CCDC */\ + MUX_VAL(CP(CCDC_PCLK), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CCDC_FIELD), (IEN | PTD | DIS | M1)) \ + MUX_VAL(CP(CCDC_HD), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CCDC_VD), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CCDC_WEN), (IEN | PTD | DIS | M1)) \ + MUX_VAL(CP(CCDC_DATA0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA3), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA4), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA5), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA6), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA7), (IEN | PTD | DIS | M0)) \ + /* RMII */\ + MUX_VAL(CP(RMII_MDIO_DATA), (IEN | M0)) \ + MUX_VAL(CP(RMII_MDIO_CLK), (M0)) \ + MUX_VAL(CP(RMII_RXD0) , (IEN | PTD | M0)) \ + MUX_VAL(CP(RMII_RXD1), (IEN | PTD | M0)) \ + MUX_VAL(CP(RMII_CRS_DV), (IEN | PTD | M0)) \ + MUX_VAL(CP(RMII_RXER), (PTD | M0)) \ + MUX_VAL(CP(RMII_TXD0), (PTD | M0)) \ + MUX_VAL(CP(RMII_TXD1), (PTD | M0)) \ + MUX_VAL(CP(RMII_TXEN), (PTD | M0)) \ + MUX_VAL(CP(RMII_50MHZ_CLK), (IEN | PTD | EN | M0)) \ + /* HECC */\ + MUX_VAL(CP(HECC1_TXD), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(HECC1_RXD), (IEN | PTU | EN | M0)) \ + /* HSUSB */\ + MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(USB0_DRVBUS), (IEN | PTD | EN | M0)) \ + /* HDQ */\ + MUX_VAL(CP(HDQ_SIO), (IEN | PTU | EN | M0)) \ + /* Control and debug */\ + MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0)) \ + /*SYS_nRESWARM */\ + MUX_VAL(CP(SYS_NRESWARM), (IDIS | PTU | DIS | M4)) \ + /* - GPIO30 */\ + MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) /*GPIO_2*/\ + /* - PEN_IRQ */\ + MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) /*GPIO_3 */\ + MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /*GPIO_4*/\ + MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) /*GPIO_5*/\ + MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) /*GPIO_6*/\ + MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4)) /*GPIO_7*/\ + MUX_VAL(CP(SYS_BOOT6), (IDIS | PTD | DIS | M4)) /*GPIO_8*/\ + /* - VIO_1V8*/\ + MUX_VAL(CP(SYS_BOOT7), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(SYS_BOOT8), (IEN | PTD | EN | M0)) \ + \ + MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTU | EN | M0)) \ + /* JTAG */\ + MUX_VAL(CP(JTAG_nTRST), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(JTAG_TCK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(JTAG_TMS), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(JTAG_TDI), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(JTAG_EMU0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(JTAG_EMU1), (IEN | PTD | DIS | M0)) \ + /* ETK (ES2 onwards) */\ + MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D0_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D1_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D2_ES2), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(ETK_D3_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D4_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D5_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D6_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D7_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D8_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D9_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D10_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D11_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M0)) \ + /* Die to Die */\ + MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)) \ + +#endif diff --git a/board/logicpd/am3517evm/config.mk b/board/logicpd/am3517evm/config.mk new file mode 100644 index 0000000..f7a35ce --- /dev/null +++ b/board/logicpd/am3517evm/config.mk @@ -0,0 +1,30 @@ +# +# Author: Vaibhav Hiremath <hvaibhav(a)ti.com> +# +# Based on ti/evm/config.mk +# +# Copyright (C) 2010 +# Texas Instruments Incorporated - http://www.ti.com/ +# +# This program is free software; you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation; either version 2 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +# +# Physical Address: +# 8000'0000 (bank0) +# A000/0000 (bank1) +# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000 +# (mem base + reserved) + +# For use with external or internal boots. +TEXT_BASE = 0x80e80000 diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h new file mode 100644 index 0000000..63f853a --- /dev/null +++ b/include/configs/am3517_evm.h @@ -0,0 +1,296 @@ +/* + * am3517_evm.h - Default configuration for AM3517 EVM board. + * + * Author: Vaibhav Hiremath <hvaibhav(a)ti.com> + * + * Based on omap3_evm_config.h + * + * Copyright (C) 2009 Texas Instruments Incorporated + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */ +#define CONFIG_OMAP 1 /* in a TI OMAP core */ +#define CONFIG_OMAP34XX 1 /* which is a 34XX */ +#define CONFIG_OMAP3_AM3517EVM 1 /* working with AM3517EVM */ + +#define CONFIG_EMIF4 1 /* The chip has EMIF4 controller */ + +#include <asm/arch/cpu.h> /* get chip and board defs */ +#include <asm/arch/omap3.h> + +/* + * Display CPU and Board information + */ +#define CONFIG_DISPLAY_CPUINFO 1 +#define CONFIG_DISPLAY_BOARDINFO 1 + +/* Clock Defines */ +#define V_OSCK 26000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK >> 1) + +#undef CONFIG_USE_IRQ /* no support for IRQs */ +#define CONFIG_MISC_INIT_R + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 +#define CONFIG_REVISION_TAG 1 + +/* + * Size of malloc() pool + */ +#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */ + /* initial data */ +/* + * DDR related + */ +#define CONFIG_OMAP3_MICRON_DDR 1 /* Micron DDR */ +#define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024) + +/* + * Hardware drivers + */ + +/* + * NS16550 Configuration + */ +#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ + +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK + +/* + * select serial console configuration + */ +#define CONFIG_CONS_INDEX 3 +#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 +#define CONFIG_SERIAL3 3 /* UART3 on AM3517 EVM */ + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ + 115200} +#define CONFIG_MMC 1 +#define CONFIG_OMAP3_MMC 1 +#define CONFIG_DOS_PARTITION 1 + +/* commands to include */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_EXT2 /* EXT2 Support */ +#define CONFIG_CMD_FAT /* FAT support */ +#define CONFIG_CMD_JFFS2 /* JFFS2 Support */ + +#define CONFIG_CMD_I2C /* I2C serial bus support */ +#define CONFIG_CMD_MMC /* MMC support */ +#define CONFIG_CMD_NAND /* NAND support */ +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING + +#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */ +#undef CONFIG_CMD_FPGA /* FPGA configuration Support */ +#undef CONFIG_CMD_IMI /* iminfo */ +#undef CONFIG_CMD_IMLS /* List all found images */ + +#define CONFIG_SYS_NO_FLASH +#define CONFIG_HARD_I2C 1 +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_BUS 0 +#define CONFIG_SYS_I2C_BUS_SELECT 1 +#define CONFIG_DRIVER_OMAP34XX_I2C 1 + +#undef CONFIG_CMD_NET +/* + * Board NAND Info. + */ +#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ + /* to access nand */ +#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ + /* to access */ + /* nand at CS0 */ + +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */ + /* NAND devices */ +#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ + +#define CONFIG_JFFS2_NAND +/* nand device jffs2 lives on */ +#define CONFIG_JFFS2_DEV "nand0" +/* start of jffs2 partition */ +#define CONFIG_JFFS2_PART_OFFSET 0x680000 +#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* sz of jffs2 part */ + +/* Environment information */ +#define CONFIG_BOOTDELAY 10 + +#define CONFIG_BOOTFILE uImage + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "loadaddr=0x82000000\0" \ + "console=ttyS2,115200n8\0" \ + "mmcargs=setenv bootargs console=${console} " \ + "root=/dev/mmcblk0p2 rw " \ + "rootfstype=ext3 rootwait\0" \ + "nandargs=setenv bootargs console=${console} " \ + "root=/dev/mtdblock4 rw " \ + "rootfstype=jffs2\0" \ + "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source ${loadaddr}\0" \ + "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "bootm ${loadaddr}\0" \ + "nandboot=echo Booting from nand ...; " \ + "run nandargs; " \ + "nand read ${loadaddr} 280000 400000; " \ + "bootm ${loadaddr}\0" \ + +#define CONFIG_BOOTCOMMAND \ + "if mmc init; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loaduimage; then " \ + "run mmcboot; " \ + "else run nandboot; " \ + "fi; " \ + "fi; " \ + "else run nandboot; fi" + +#define CONFIG_AUTO_COMPLETE 1 +/* + * Miscellaneous configurable options + */ +#define V_PROMPT "AM3517_EVM # " + +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_PROMPT V_PROMPT +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 32 /* max number of command */ + /* args */ +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) +/* memtest works on */ +#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) +#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ + 0x01F00000) /* 31MB */ + +#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */ + /* address */ + +/* + * AM3517 has 12 GP timers, they can be driven by the system clock + * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). + * This rate is divided by a local divisor. + */ +#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2 +#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ +#define CONFIG_SYS_HZ 1000 + +/*----------------------------------------------------------------------- + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */ +#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */ +#endif + +/*----------------------------------------------------------------------- + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ +#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 +#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */ +#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 + +/* SDRAM Bank Allocation method */ +#define SDRC_R_B_C 1 + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ + +/* **** PISMO SUPPORT *** */ + +/* Configure the PISMO */ +#define PISMO1_NAND_SIZE GPMC_SIZE_128M +#define PISMO1_ONEN_SIZE GPMC_SIZE_128M + +#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */ + /* on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ + +#define CONFIG_SYS_FLASH_BASE boot_flash_base + +/* Monitor at start of flash */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE + +#define CONFIG_NAND_OMAP_GPMC +#define GPMC_NAND_ECC_LP_x16_LAYOUT 1 +#define CONFIG_ENV_IS_IN_NAND 1 +#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */ + +#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec +#define CONFIG_ENV_OFFSET boot_flash_off +#define CONFIG_ENV_ADDR boot_flash_env_addr + +/*----------------------------------------------------------------------- + * CFI FLASH driver setup + */ +/* timeout values are in ticks */ +#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ) +#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ) + +/* Flash banks JFFS2 should use */ +#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \ + CONFIG_SYS_MAX_NAND_DEVICE) +#define CONFIG_SYS_JFFS2_MEM_NAND +/* use flash_info[2] */ +#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS +#define CONFIG_SYS_JFFS2_NUM_BANKS 1 + +#ifndef __ASSEMBLY__ +extern unsigned int boot_flash_base; +extern volatile unsigned int boot_flash_env_addr; +extern unsigned int boot_flash_off; +extern unsigned int boot_flash_sec; +extern unsigned int boot_flash_type; +#endif + +#endif /* __CONFIG_H */ -- 1.6.2.4

3 6

[U-Boot] ARM pull request.
by Tom Rix 07 Jun '10

07 Jun '10

This is to catch master up to ARM mach-types Tom The following changes since commit 01f03bda5b22e5aeae5f02fd537da97a41485c73: Wolfgang Denk (1): Prepare v2010.06-rc1 are available in the git repository at: git://git.denx.de/u-boot-arm master Tom (2): ARM Update mach-types ARM Update mach-types arch/arm/include/asm/mach-types.h | 1173 ++++++++++++++++++++++++++++++++++++- 1 files changed, 1165 insertions(+), 8 deletions(-)

4 4

[U-Boot] [PATCH v3] add new board pm9g45
by Asen Dimov 07 Jun '10

07 Jun '10

Add the new board PM9G45 from Ronetix GmbH. * AT91SAM9G45 MCU at 400Mhz. * 128MB DDR2 SDRAM * 256MB NAND * 10/100 MBits Ethernet DP83848 * Serial number chip DS2401 The board is made as SODIMM200 module. For more info www.ronatix.at or info(a)ronetix.at. Signed-off-by: Asen Dimov <dimov(a)ronetix.at> --- MAINTAINERS | 1 + MAKEALL | 1 + Makefile | 4 + board/ronetix/pm9g45/Makefile | 54 ++++++ .../at91sam9m10g45ek => ronetix/pm9g45}/config.mk | 0 board/ronetix/pm9g45/pm9g45.c | 188 ++++++++++++++++++++ include/configs/pm9g45.h | 186 +++++++++++++++++++ 7 files changed, 434 insertions(+), 0 deletions(-) create mode 100644 board/ronetix/pm9g45/Makefile copy board/{atmel/at91sam9m10g45ek => ronetix/pm9g45}/config.mk (100%) create mode 100644 board/ronetix/pm9g45/pm9g45.c create mode 100644 include/configs/pm9g45.h diff --git a/MAINTAINERS b/MAINTAINERS index 0e759c9..a3993fc 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -224,6 +224,7 @@ Ilko Iliev <iliev(a)ronetix.at> PM9261 AT91SAM9261 PM9263 AT91SAM9263 + PM9G45 ARM926EJS (AT91SAM9G45 SoC) Gary Jennejohn <garyj(a)denx.de> diff --git a/MAKEALL b/MAKEALL index b15d407..911983e 100755 --- a/MAKEALL +++ b/MAKEALL @@ -672,6 +672,7 @@ LIST_at91=" \ otc570 \ pm9261 \ pm9263 \ + pm9g45 \ SBC35_A9G20 \ TNY_A9260 \ TNY_A9G20 \ diff --git a/Makefile b/Makefile index 8b4e0b9..46845a5 100644 --- a/Makefile +++ b/Makefile @@ -2871,6 +2871,10 @@ otc570_config : unconfig pm9263_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm926ejs pm9263 ronetix at91 +pm9g45_config : unconfig + @mkdir -p $(obj)include + @$(MKCONFIG) -a pm9g45 arm arm926ejs pm9g45 ronetix at91 + SBC35_A9G20_NANDFLASH_config \ SBC35_A9G20_EEPROM_config \ SBC35_A9G20_config : unconfig diff --git a/board/ronetix/pm9g45/Makefile b/board/ronetix/pm9g45/Makefile new file mode 100644 index 0000000..dd5b02e --- /dev/null +++ b/board/ronetix/pm9g45/Makefile @@ -0,0 +1,54 @@ +# +# (C) Copyright 2003-2008 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# (C) Copyright 2008 +# Stelian Pop <stelian.pop(a)leadtechdesign.com> +# Lead Tech Design <www.leadtechdesign.com> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y += pm9g45.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/atmel/at91sam9m10g45ek/config.mk b/board/ronetix/pm9g45/config.mk similarity index 100% copy from board/atmel/at91sam9m10g45ek/config.mk copy to board/ronetix/pm9g45/config.mk diff --git a/board/ronetix/pm9g45/pm9g45.c b/board/ronetix/pm9g45/pm9g45.c new file mode 100644 index 0000000..3b4d9a3 --- /dev/null +++ b/board/ronetix/pm9g45/pm9g45.c @@ -0,0 +1,188 @@ +/* + * (C) Copyright 2010 + * Ilko Iliev <iliev(a)ronetix.at> + * Asen Dimov <dimov(a)ronetix.at> + * Ronetix GmbH <www.ronetix.at> + * + * (C) Copyright 2007-2008 + * Stelian Pop <stelian.pop(a)leadtechdesign.com> + * Lead Tech Design <www.leadtechdesign.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/sizes.h> +#include <asm/arch/at91sam9g45.h> +#include <asm/arch/at91sam9_smc.h> +#include <asm/arch/at91_common.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_rstc.h> +#include <asm/arch/at91_matrix.h> +#include <asm/arch/at91_pio.h> +#include <asm/arch/clk.h> +#include <asm/arch/io.h> +#include <asm/arch/hardware.h> +#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB) +#include <net.h> +#endif +#include <netdev.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Miscelaneous platform dependent initialisations + */ + +#ifdef CONFIG_CMD_NAND +static void pm9g45_nand_hw_init(void) +{ + unsigned long csa; + at91_smc_t *smc = (at91_smc_t *) AT91_SMC_BASE; + at91_matrix_t *matrix = (at91_matrix_t *) AT91_MATRIX_BASE; + at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + + /* Enable CS3 */ + csa = readl(&matrix->ccr[6]) | AT91_MATRIX_CSA_EBI_CS3A; + writel(csa, &matrix->ccr[6]); + + /* Configure SMC CS3 for NAND/SmartMedia */ + writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[3].setup); + + writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(3) | + AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(2), + &smc->cs[3].pulse); + + writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(4), + &smc->cs[3].cycle); + + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | + AT91_SMC_MODE_DBW_8 | + AT91_SMC_MODE_TDF_CYCLE(3), + &smc->cs[3].mode); + + writel(1 << AT91SAM9G45_ID_PIOC, &pmc->pcer); + +#ifdef CONFIG_SYS_NAND_READY_PIN + /* Configure RDY/BSY */ + at91_set_pio_input(CONFIG_SYS_NAND_READY_PIN, 1); +#endif + + /* Enable NandFlash */ + at91_set_pio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); +} +#endif + +#ifdef CONFIG_MACB +static void pm9g45_macb_hw_init(void) +{ + at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + at91_pio_t *pio = (at91_pio_t *) AT91_PIO_BASE; + + /* + * PD2 enables the 50MHz oscillator for Ethernet PHY + * 1 - enable + * 0 - disable + */ + at91_set_pio_output(AT91_PIO_PORTD, 2, 1); + at91_set_pio_value(AT91_PIO_PORTD, 2, 1); /* 1- enable, 0 - disable */ + + /* Enable clock */ + writel(1 << AT91SAM9G45_ID_EMAC, &pmc->pcer); + + /* + * Disable pull-up on: + * RXDV (PA15) => PHY normal mode (not Test mode) + * ERX0 (PA12) => PHY ADDR0 + * ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0 + * + * PHY has internal pull-down + */ + at91_set_pio_pullup(AT91_PIO_PORTA, 15, 0); + at91_set_pio_pullup(AT91_PIO_PORTA, 12, 0); + at91_set_pio_pullup(AT91_PIO_PORTA, 13, 0); + + /* Re-enable pull-up */ + at91_set_pio_pullup(AT91_PIO_PORTA, 15, 1); + at91_set_pio_pullup(AT91_PIO_PORTA, 12, 1); + at91_set_pio_pullup(AT91_PIO_PORTA, 13, 1); + + at91_macb_hw_init(); +} +#endif + +int board_init(void) +{ + at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + + /* Enable Ctrlc */ + console_init_f(); + + writel((1 << AT91SAM9G45_ID_PIOA) | + (1 << AT91SAM9G45_ID_PIOB) | + (1 << AT91SAM9G45_ID_PIOC) | + (1 << AT91SAM9G45_ID_PIODE), &pmc->pcer); + + /* arch number of AT91SAM9M10G45EK-Board */ + gd->bd->bi_arch_number = MACH_TYPE_PM9G45; + /* adress of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + + at91_serial_hw_init(); +#ifdef CONFIG_CMD_NAND + pm9g45_nand_hw_init(); +#endif + +#ifdef CONFIG_MACB + pm9g45_macb_hw_init(); +#endif + return 0; +} + +int dram_init(void) +{ + gd->bd->bi_dram[0].start = PHYS_SDRAM; + gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE; + return 0; +} + +#ifdef CONFIG_RESET_PHY_R +void reset_phy(void) +{ +#ifdef CONFIG_MACB + /* + * Initialize ethernet HW addr prior to starting Linux, + * needed for nfsroot + */ + eth_init(gd->bd); +#endif +} +#endif + +int board_eth_init(bd_t *bis) +{ + int rc = 0; +#ifdef CONFIG_MACB + rc = macb_eth_initialize(0, (void *)AT91_EMAC_BASE, 0x01); +#endif + return rc; +} diff --git a/include/configs/pm9g45.h b/include/configs/pm9g45.h new file mode 100644 index 0000000..690f119 --- /dev/null +++ b/include/configs/pm9g45.h @@ -0,0 +1,186 @@ +/* + * (C) Copyright 2010 + * Ilko Iliev <iliev(a)ronetix.at> + * Asen Dimov <dimov(a)ronetix.at> + * Ronetix GmbH <www.ronetix.at> + * + * (C) Copyright 2007-2008 + * Stelian Pop <stelian.pop(a)leadtechdesign.com> + * Lead Tech Design <www.leadtechdesign.com> + * + * Configuation settings for the PM9G45 board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */ +#define CONFIG_PM9G45 1 /* It's an Ronetix PM9G45 */ +#define CONFIG_AT91SAM9G45 1 /* It's an Atmel AT91SAM9G45 SoC */ + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */ +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_ARCH_CPU_INIT + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 + +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SKIP_RELOCATE_UBOOT + +/* + * Hardware drivers + */ +#define CONFIG_AT91_GPIO 1 +#define CONFIG_ATMEL_USART 1 +#define CONFIG_USART3 1 /* USART 3 is DBGU */ + +#define CONFIG_SYS_USE_NANDFLASH 1 + +/* LED */ +#define CONFIG_AT91_LED +#define CONFIG_RED_LED AT91_PIO_PORTD, 31 /* this is the user1 led */ +#define CONFIG_GREEN_LED AT91_PIO_PORTD, 0 /* this is the user2 led */ + +#define CONFIG_BOOTDELAY 3 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE 1 +#define CONFIG_BOOTP_BOOTPATH 1 +#define CONFIG_BOOTP_GATEWAY 1 +#define CONFIG_BOOTP_HOSTNAME 1 + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMLS + +#define CONFIG_CMD_PING 1 +#define CONFIG_CMD_DHCP 1 +#define CONFIG_CMD_NAND 1 +#define CONFIG_CMD_USB 1 + +#define CONFIG_CMD_JFFS2 1 +#define CONFIG_JFFS2_CMDLINE 1 +#define CONFIG_JFFS2_NAND 1 +#define CONFIG_JFFS2_DEV "nand0" /* NAND dev jffs2 lives on */ +#define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */ +#define CONFIG_JFFS2_PART_SIZE (256 * 1024 * 1024) /* partition */ + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM 0x70000000 +#define PHYS_SDRAM_SIZE 0x08000000 /* 128 megs */ + +/* NOR flash, not available */ +#define CONFIG_SYS_NO_FLASH 1 +#undef CONFIG_CMD_FLASH + +/* NAND flash */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_MAX_CHIPS 1 +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE 0x40000000 +#define CONFIG_SYS_NAND_DBW_8 1 +/* our ALE is AD21 */ +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +/* our CLE is AD22 */ +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTC, 14 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTD, 3 + +#endif + +/* Ethernet */ +#define CONFIG_MACB 1 +#define CONFIG_RMII 1 +#define CONFIG_NET_MULTI 1 +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_RESET_PHY_R 1 + +/* USB */ +#define CONFIG_USB_ATMEL +#define CONFIG_USB_OHCI_NEW 1 +#define CONFIG_DOS_PARTITION 1 +#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 +#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00700000 /* _UHP_OHCI_BASE */ +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g45" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 +#define CONFIG_USB_STORAGE 1 + +/* board specific(not enough SRAM) */ +#define CONFIG_AT91SAM9G45_LCD_BASE PHYS_SDRAM + 0xE00000 + +#define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM + 0x2000000 /* load addr */ + +#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM +#define CONFIG_SYS_MEMTEST_END CONFIG_AT91SAM9G45_LCD_BASE + +/* bootstrap + u-boot + env + linux in nandflash */ +#define CONFIG_ENV_IS_IN_NAND 1 +#define CONFIG_ENV_OFFSET 0x60000 +#define CONFIG_ENV_OFFSET_REDUND 0x80000 +#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ +#define CONFIG_BOOTCOMMAND "nand read 0x72000000 0x200000 0x200000; bootm" +#define CONFIG_BOOTARGS "fbcon=rotate:3 console=tty0 " \ + "console=ttyS0,115200 " \ + "root=/dev/mtdblock4 " \ + "mtdparts=atmel_nand:128k(bootstrap)ro," \ + "256k(uboot)ro,1664k(env)," \ + "2M(linux)ro,-(root) rw " \ + "rootfstype=jffs2" + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 } + +#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_LONGHELP 1 +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024,\ + 0x1000) +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* 128 bytes for initial data */ + +#define CONFIG_STACKSIZE (32*1024) /* regular stack */ + +#ifdef CONFIG_USE_IRQ +#error CONFIG_USE_IRQ not supported +#endif + +#endif -- 1.5.5.6

3 2