March 2008 - U-Boot

[U-Boot-Users] => tftp 100000 fpganew.bit Using FEC ETHERNET device TFTP from server 192.168.1.100; our IP address is 192.168.1.1 Filename 'fpganew.bit'. Load address: 0x100000 Loading: ######### done Bytes transferred = 131034 (1ffda hex) => fpga loadb 0 100000 ${
by Tales Toledo 25 Mar '08

25 Mar '08

Hi, does anybody have a CRC problem programming Xilinx Spartan3 in slave serial mode? I'm using u-boot-1.3.0 with Matthias suggested changes in bit swapping and always get the same error. The .bit is ok since it was programmed using JTAG and works fine. The command sequence and u-boot debug messages are below for reference. Any suggestion is appreciated. Thx, TT => tftp 100000 fpganew.bit Using FEC ETHERNET device TFTP from server 192.168.1.100; our IP address is 192.168.1.1 Filename 'fpganew.bit'. Load address: 0x100000 Loading: ######### done Bytes transferred = 131034 (1ffda hex) => fpga loadb 0 100000 ${filesize} do_fpga: fpga_data = 0x100000 do_fpga: device = 0 design filename = "fpga_top.ncd" part number = "3s200tq144" date = "2008/ 3/25" time = "16:37:58" bytes in bitstream = 130952 fpga_get_desc: found fpga descriptor #0 @ 0x01ffad04 Spartan3_load: Launching Slave Serial Load Spartan3_ss_load: start with interface functions @ 0x01ff8c00 Spartan3_ss_load: Function Table: ptr: 0x01bb6a90 struct: 0x01ff8c00 pgm: 0x01febf80 init: 0x01fec000 clk: 0x01fec0e8 wr: 0x01fec118 done: 0x01fec070 Loading FPGA Device 0... fpga_pre_fn:111: FPGA pre-configuration fpga_pgm_fn:122: FPGA PROGRAM asserted fpga_init_fn:145: INIT check... low fpga_pgm_fn:122: FPGA PROGRAM deasserted fpga_init_fn:145: INIT check... high ........................................fpga_init_fn:145: INIT check... high fpga_init_fn:145: INIT check... low ** CRC error during FPGA load. bytecount=130938, bsize=130952

1 0

[U-Boot-Users] Regarding my patch to move FSL boards...
by Jon Loeliger 25 Mar '08

25 Mar '08

Wolfgang, I sent a patch last week that moved 3 FSL boards from board/ so that they would instead be under board/freescale/. As that patch is for a 7448, 826x and 8266 families, I didn't apply it to my mpc86xx repository. Would you be willing to apply that patch directly when you get a chance? Or, if you would prefer, I can apply it to my 86xx repository and have you pull it. Your preference! Thanks, jdl

2 1

[U-Boot-Users] U-Boot 1.3.2 release
by Wolfgang Denk 25 Mar '08

25 Mar '08

Hi everybody, U-Boot v1.3.2 has been released and is available from the git repository and the FTP server. The Merge Window for v1.3.3 is open until Mar 31, 23:59:59 MET. Release v1.3.3 is scheduled for May 12, but you know that you better don't hold your breath. A little statistics - changes since release v1.3.1: 858 csets from 101 developers 34 employers found A total of 180495 lines added, 55592 removed (delta 124903) Developers with the most changesets Stefan Roese 111 (12.9%) Kumar Gala 61 (7.1%) Wolfgang Denk 58 (6.8%) Jean-Christophe PLAGNIOL-VILLARD 37 (4.3%) Matthias Fuchs 35 (4.1%) Larry Johnson 32 (3.7%) Mike Frysinger 32 (3.7%) Haavard Skinnemoen 28 (3.3%) Nobuhiro Iwamatsu 25 (2.9%) Dave Liu 22 (2.6%) ... Developers with the most changed lines Mike Frysinger 61837 (31.8%) Wolfgang Denk 17556 (9.0%) TsiChung Liew 14534 (7.5%) Kumar Gala 13081 (6.7%) Stefan Roese 11118 (5.7%) Matthias Fuchs 7143 (3.7%) Nobuhiro Iwamatsu 6540 (3.4%) Larry Johnson 6048 (3.1%) Michael Schwingen 5771 (3.0%) Haavard Skinnemoen 4327 (2.2%) ... Developers with the most lines removed Andreas Engel 1422 (2.6%) Kumar Gala 1335 (2.4%) Marian Balakowicz 337 (0.6%) Paul Gortmaker 325 (0.6%) Becky Bruce 290 (0.5%) Shinya Kuribayashi 145 (0.3%) Ladislav Michl 137 (0.2%) Bernhard Nemec 22 (0.0%) Andy Fleming 8 (0.0%) Michael Firth 8 (0.0%) ... Developers with the most signoffs (total 1697) Stefan Roese 244 (14.4%) Kumar Gala 127 (7.5%) Wolfgang Denk 127 (7.5%) Kim Phillips 89 (5.2%) Jean-Christophe PLAGNIOL-VILLARD 79 (4.7%) Matthias Fuchs 72 (4.2%) Larry Johnson 66 (3.9%) Mike Frysinger 60 (3.5%) Haavard Skinnemoen 59 (3.5%) Nobuhiro Iwamatsu 53 (3.1%) ... Top changeset contributors by employer DENX 295 (34.4%) Freescale 208 (24.2%) (Unknown) 116 (13.5%) ESD Electronics 35 (4.1%) ACM 32 (3.7%) Gentoo 32 (3.7%) Funky 29 (3.4%) Semihalf 17 (2.0%) Netstal-Maschinen 13 (1.5%) TQ Systems 12 (1.4%) ... Top lines changed by employer Gentoo 61912 (31.8%) Freescale 40796 (21.0%) DENX 35173 (18.1%) (Unknown) 17694 (9.1%) ESD Electronics 9607 (4.9%) ACM 7872 (4.0%) Funky 4386 (2.3%) Semihalf 3568 (1.8%) ARM 2622 (1.3%) Embedded Specialties 1654 (0.8%) ... Best regards, Wolfgang Denk -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd(a)denx.de So we follow our wandering paths, and the very darkness acts as our guide and our doubts serve to reassure us. - Jean-Pierre de Caussade, eighteenth-century Jesuit priest

5 8

[U-Boot-Users] [PATCH] [new uImage] Fix build issue on ARM
by Kumar Gala 25 Mar '08

25 Mar '08

ARM platforms don't have a bd->bi_memsize so use bd->bi_dram[0].size instead. Signed-off-by: Kumar Gala <galak(a)kernel.crashing.org> --- Let's see if this fixes the issue on ARM. common/image.c | 8 +++++++- 1 files changed, 7 insertions(+), 1 deletions(-) diff --git a/common/image.c b/common/image.c index 9e446fa..4e0e96d 100644 --- a/common/image.c +++ b/common/image.c @@ -140,8 +140,10 @@ ulong getenv_bootm_low(void) return tmp; } -#ifdef CFG_SDRAM_BASE +#if defined(CFG_SDRAM_BASE) return CFG_SDRAM_BASE; +#elif defined(CONFIG_ARM) + return gd->bd->bi_dram[0].start; #else return 0; #endif @@ -155,7 +157,11 @@ ulong getenv_bootm_size(void) return tmp; } +#if defined(CONFIG_ARM) + return gd->bd->bi_dram[0].size; +#else return gd->bd->bi_memsize; +#endif } void memmove_wd (void *to, void *from, size_t len, ulong chunksz) -- 1.5.4.1

2 1

[U-Boot-Users] [PATCH] net: Divided code of NE2000 ethernet driver
by goda.yusuke 25 Mar '08

25 Mar '08

There are more devices of the NE2000 base. A present code is difficult for us to support more devices. To support more NE2000 clone devices, separated the function. Signed-off-by: Yusuke Goda <goda.yusuke(a)renesas.com> --- drivers/net/ne2000.c | 213 +++++++++--------------------- drivers/net/ne2000.h | 316 ++++++++++++++++----------------------------- drivers/net/ne2000_base.h | 282 ++++++++++++++++++++++++++++++++++++++++ 3 files changed, 456 insertions(+), 355 deletions(-) create mode 100644 drivers/net/ne2000_base.h diff --git a/drivers/net/ne2000.c b/drivers/net/ne2000.c index b100657..4928014 100644 --- a/drivers/net/ne2000.c +++ b/drivers/net/ne2000.c @@ -82,25 +82,11 @@ Add SNMP #ifdef CONFIG_DRIVER_NE2000 -/* wor around udelay resetting OCR */ -static void my_udelay(long us) { - long tmo; - - tmo = get_timer (0) + us * CFG_HZ / 1000000; /* will this be much greater than 0 ? */ - while (get_timer (0) < tmo); -} - -#define mdelay(n) my_udelay((n)*1000) - +#define mdelay(n) udelay((n)*1000) /* forward definition of function used for the uboot interface */ void uboot_push_packet_len(int len); void uboot_push_tx_done(int key, int val); -/* timeout for tx/rx in s */ -#define TOUT 5 - -#define ETHER_ADDR_LEN 6 - /* ------------------------------------------------------------------------ Debugging details @@ -118,18 +104,18 @@ void uboot_push_tx_done(int key, int val); #if DEBUG & 1 #define DEBUG_FUNCTION() do { printf("%s\n", __FUNCTION__); } while (0) #define DEBUG_LINE() do { printf("%d\n", __LINE__); } while (0) +#define PRINTK(args...) printf(args) #else #define DEBUG_FUNCTION() do {} while(0) #define DEBUG_LINE() do {} while(0) +#define PRINTK(args...) #endif -#include "ne2000.h" +/* NE2000 base header file */ +#include "ne2000_base.h" -#if DEBUG & 1 -#define PRINTK(args...) printf(args) -#else -#define PRINTK(args...) -#endif +/* Basic NE2000 chip support */ +#include "ne2000.h" static dp83902a_priv_data_t nic; /* just one instance of the card supported */ @@ -137,8 +123,7 @@ static bool dp83902a_init(void) { dp83902a_priv_data_t *dp = &nic; - cyg_uint8* base; - int i; + u8* base; DEBUG_FUNCTION(); @@ -147,6 +132,7 @@ dp83902a_init(void) DEBUG_LINE(); +#if defined(NE2000_BASIC_INIT) /* Prepare ESA */ DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE1); /* Select page 1 */ /* Use the address from the serial EEPROM */ @@ -163,6 +149,7 @@ dp83902a_init(void) dp->esa[4], dp->esa[5] ); +#endif /* NE2000_BASIC_INIT */ return true; } @@ -170,7 +157,7 @@ static void dp83902a_stop(void) { dp83902a_priv_data_t *dp = &nic; - cyg_uint8 *base = dp->base; + u8 *base = dp->base; DEBUG_FUNCTION(); @@ -188,10 +175,10 @@ dp83902a_stop(void) the hardware ready to send/receive packets. */ static void -dp83902a_start(unsigned char * enaddr) +dp83902a_start(u8 * enaddr) { dp83902a_priv_data_t *dp = &nic; - cyg_uint8 *base = dp->base; + u8 *base = dp->base; int i; DEBUG_FUNCTION(); @@ -206,15 +193,20 @@ dp83902a_start(unsigned char * enaddr) dp->tx1 = dp->tx2 = 0; dp->tx_next = dp->tx_buf1; dp->tx_started = false; + dp->running = true; DP_OUT(base, DP_PSTART, dp->rx_buf_start); /* Receive ring start page */ DP_OUT(base, DP_BNDRY, dp->rx_buf_end-1); /* Receive ring boundary */ DP_OUT(base, DP_PSTOP, dp->rx_buf_end); /* Receive ring end page */ dp->rx_next = dp->rx_buf_start-1; + dp->running = true; DP_OUT(base, DP_ISR, 0xFF); /* Clear any pending interrupts */ DP_OUT(base, DP_IMR, DP_IMR_All); /* Enable all interrupts */ DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE1 | DP_CR_STOP); /* Select page 1 */ DP_OUT(base, DP_P1_CURP, dp->rx_buf_start); /* Current page - next free page for Rx */ + dp->running = true; for (i = 0; i < ETHER_ADDR_LEN; i++) { + /* FIXME */ + //*((vu_short*)( base + ((DP_P1_PAR0 + i) * 2) + 0x1400)) = enaddr[i]; DP_OUT(base, DP_P1_PAR0+i, enaddr[i]); } /* Enable and start device */ @@ -222,6 +214,7 @@ dp83902a_start(unsigned char * enaddr) DP_OUT(base, DP_TCR, DP_TCR_NORMAL); /* Normal transmit operations */ DP_OUT(base, DP_RCR, DP_RCR_AB); /* Accept broadcast, no errors, no multicast */ dp->running = true; + } /* @@ -234,7 +227,7 @@ static void dp83902a_start_xmit(int start_page, int len) { dp83902a_priv_data_t *dp = (dp83902a_priv_data_t *) &nic; - cyg_uint8 *base = dp->base; + u8 *base = dp->base; DEBUG_FUNCTION(); @@ -259,10 +252,10 @@ dp83902a_start_xmit(int start_page, int len) that there is free buffer space (dp->tx_next). */ static void -dp83902a_send(unsigned char *data, int total_len, unsigned long key) +dp83902a_send(u8 *data, int total_len, u32 key) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - cyg_uint8 *base = dp->base; + u8 *base = dp->base; int len, start_page, pkt_len, i, isr; #if DEBUG & 4 int dx; @@ -296,7 +289,7 @@ dp83902a_send(unsigned char *data, int total_len, unsigned long key) /* but the code is extended a bit to do what Hitachi's monitor */ /* does (i.e., also read data). */ - cyg_uint16 tmp; + u16 tmp; int len = 1; DP_OUT(base, DP_RSAL, 0x100-len); @@ -322,7 +315,7 @@ dp83902a_send(unsigned char *data, int total_len, unsigned long key) /* Put data into buffer */ #if DEBUG & 4 - printf(" sg buf %08lx len %08x\n ", (unsigned long) data, len); + printf(" sg buf %08lx len %08x\n ", (u32)data, len); dx = 0; #endif while (len > 0) { @@ -330,6 +323,7 @@ dp83902a_send(unsigned char *data, int total_len, unsigned long key) printf(" %02x", *data); if (0 == (++dx % 16)) printf("\n "); #endif + DP_OUT_DATA(dp->data, *data++); len--; } @@ -358,6 +352,7 @@ dp83902a_send(unsigned char *data, int total_len, unsigned long key) do { DP_IN(base, DP_ISR, isr); } while ((isr & DP_ISR_RDC) == 0); + /* Then disable DMA */ DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START); @@ -383,9 +378,9 @@ static void dp83902a_RxEvent(void) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - cyg_uint8 *base = dp->base; - unsigned char rsr; - unsigned char rcv_hdr[4]; + u8 *base = dp->base; + u8 rsr; + u8 rcv_hdr[4]; int i, len, pkt, cur; DEBUG_FUNCTION(); @@ -423,6 +418,7 @@ dp83902a_RxEvent(void) CYGACC_CALL_IF_DELAY_US(10); #endif + /* read header (get data size)*/ for (i = 0; i < sizeof(rcv_hdr);) { DP_IN_DATA(dp->data, rcv_hdr[i++]); } @@ -432,7 +428,10 @@ dp83902a_RxEvent(void) rcv_hdr[0], rcv_hdr[1], rcv_hdr[2], rcv_hdr[3]); #endif len = ((rcv_hdr[3] << 8) | rcv_hdr[2]) - sizeof(rcv_hdr); + + /* data read */ uboot_push_packet_len(len); + if (rcv_hdr[1] == dp->rx_buf_start) DP_OUT(base, DP_BNDRY, dp->rx_buf_end-1); else @@ -448,12 +447,12 @@ dp83902a_RxEvent(void) efficient processing in the upper layers of the stack. */ static void -dp83902a_recv(unsigned char *data, int len) +dp83902a_recv(u8 *data, int len) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - cyg_uint8 *base = dp->base; + u8 *base = dp->base; int i, mlen; - cyg_uint8 saved_char = 0; + u8 saved_char = 0; bool saved; #if DEBUG & 4 int dx; @@ -482,7 +481,7 @@ dp83902a_recv(unsigned char *data, int len) if (data) { mlen = len; #if DEBUG & 4 - printf(" sg buf %08lx len %08x \n", (unsigned long) data, mlen); + printf(" sg buf %08lx len %08x \n", (u32) data, mlen); dx = 0; #endif while (0 < mlen) { @@ -495,7 +494,7 @@ dp83902a_recv(unsigned char *data, int len) } { - cyg_uint8 tmp; + u8 tmp; DP_IN_DATA(dp->data, tmp); #if DEBUG & 4 printf(" %02x", tmp); @@ -516,9 +515,9 @@ static void dp83902a_TxEvent(void) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - cyg_uint8 *base = dp->base; - unsigned char tsr; - unsigned long key; + u8 *base = dp->base; + u8 tsr; + u32 key; DEBUG_FUNCTION(); @@ -551,8 +550,8 @@ static void dp83902a_ClearCounters(void) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - cyg_uint8 *base = dp->base; - cyg_uint8 cnt1, cnt2, cnt3; + u8 *base = dp->base; + u8 cnt1, cnt2, cnt3; DP_IN(base, DP_FER, cnt1); DP_IN(base, DP_CER, cnt2); @@ -566,8 +565,8 @@ static void dp83902a_Overflow(void) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *)&nic; - cyg_uint8 *base = dp->base; - cyg_uint8 isr; + u8 *base = dp->base; + u8 isr; /* Issue a stop command and wait 1.6ms for it to complete. */ DP_OUT(base, DP_CR, DP_CR_STOP | DP_CR_NODMA); @@ -603,8 +602,8 @@ static void dp83902a_poll(void) { struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - cyg_uint8 *base = dp->base; - unsigned char isr; + u8 *base = dp->base; + u8 isr; DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE0 | DP_CR_START); DP_IN(base, DP_ISR, isr); @@ -642,13 +641,13 @@ dp83902a_poll(void) /* find prom (taken from pc_net_cs.c from Linux) */ #include "8390.h" - +/* typedef struct hw_info_t { u_int offset; u_char a0, a1, a2; u_int flags; } hw_info_t; - +*/ #define DELAY_OUTPUT 0x01 #define HAS_MISC_REG 0x02 #define USE_BIG_BUF 0x04 @@ -731,102 +730,17 @@ static hw_info_t hw_info[] = { static hw_info_t default_info = { 0, 0, 0, 0, 0 }; -unsigned char dev_addr[6]; +u8 dev_addr[6]; #define PCNET_CMD 0x00 #define PCNET_DATAPORT 0x10 /* NatSemi-defined port window offset. */ #define PCNET_RESET 0x1f /* Issue a read to reset, a write to clear. */ #define PCNET_MISC 0x18 /* For IBM CCAE and Socket EA cards */ -unsigned long nic_base; - -static void pcnet_reset_8390(void) -{ - int i, r; - - PRINTK("nic base is %lx\n", nic_base); - - n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); - PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); - n2k_outb(E8390_NODMA+E8390_PAGE1+E8390_STOP, E8390_CMD); - PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); - n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); - PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); - n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); - - n2k_outb(n2k_inb(PCNET_RESET), PCNET_RESET); - - for (i = 0; i < 100; i++) { - if ((r = (n2k_inb(EN0_ISR) & ENISR_RESET)) != 0) - break; - PRINTK("got %x in reset\n", r); - my_udelay(100); - } - n2k_outb(ENISR_RESET, EN0_ISR); /* Ack intr. */ - - if (i == 100) - printf("pcnet_reset_8390() did not complete.\n"); -} /* pcnet_reset_8390 */ - -static hw_info_t * get_prom(void ) { - unsigned char prom[32]; - int i, j; - struct { - u_char value, offset; - } program_seq[] = { - {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/ - {0x48, EN0_DCFG}, /* Set byte-wide (0x48) access. */ - {0x00, EN0_RCNTLO}, /* Clear the count regs. */ - {0x00, EN0_RCNTHI}, - {0x00, EN0_IMR}, /* Mask completion irq. */ - {0xFF, EN0_ISR}, - {E8390_RXOFF, EN0_RXCR}, /* 0x20 Set to monitor */ - {E8390_TXOFF, EN0_TXCR}, /* 0x02 and loopback mode. */ - {32, EN0_RCNTLO}, - {0x00, EN0_RCNTHI}, - {0x00, EN0_RSARLO}, /* DMA starting at 0x0000. */ - {0x00, EN0_RSARHI}, - {E8390_RREAD+E8390_START, E8390_CMD}, - }; - - PRINTK("trying to get MAC via prom reading\n"); - - pcnet_reset_8390(); - - mdelay(10); - - for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++) - n2k_outb(program_seq[i].value, program_seq[i].offset); - - PRINTK("PROM:"); - for (i = 0; i < 32; i++) { - prom[i] = n2k_inb(PCNET_DATAPORT); - PRINTK(" %02x", prom[i]); - } - PRINTK("\n"); - for (i = 0; i < NR_INFO; i++) { - if ((prom[0] == hw_info[i].a0) && - (prom[2] == hw_info[i].a1) && - (prom[4] == hw_info[i].a2)) { - PRINTK("matched board %d\n", i); - break; - } - } - if ((i < NR_INFO) || ((prom[28] == 0x57) && (prom[30] == 0x57))) { - for (j = 0; j < 6; j++) - dev_addr[j] = prom[j<<1]; - PRINTK("on exit i is %d/%ld\n", i, NR_INFO); - PRINTK("MAC address is %02x:%02x:%02x:%02x:%02x:%02x\n", - dev_addr[0],dev_addr[1],dev_addr[2],dev_addr[3],dev_addr[4],dev_addr[5]); - return (i < NR_INFO) ? hw_info+i : &default_info; - } - return NULL; -} +u32 nic_base; /* U-boot specific routines */ - - -static unsigned char *pbuf = NULL; +static u8 *pbuf = NULL; static int pkey = -1; static int initialized=0; @@ -839,7 +753,7 @@ void uboot_push_packet_len(int len) { } dp83902a_recv(&pbuf[0], len); - /* Just pass it to the upper layer */ + /*Just pass it to the upper layer*/ NetReceive(&pbuf[0], len); } @@ -864,7 +778,7 @@ int eth_init(bd_t *bd) { #ifdef CONFIG_DRIVER_NE2000_CCR { - volatile unsigned char *p = (volatile unsigned char *) CONFIG_DRIVER_NE2000_CCR; + vu_char *p = (vu_char *) CONFIG_DRIVER_NE2000_CCR; PRINTK("CCR before is %x\n", *p); *p = CONFIG_DRIVER_NE2000_VAL; @@ -873,9 +787,9 @@ int eth_init(bd_t *bd) { #endif nic_base = CONFIG_DRIVER_NE2000_BASE; - nic.base = (cyg_uint8 *) CONFIG_DRIVER_NE2000_BASE; + nic.base = (u8 *) CONFIG_DRIVER_NE2000_BASE; - r = get_prom(); + r = get_prom(dev_addr); if (!r) return -1; @@ -886,22 +800,23 @@ int eth_init(bd_t *bd) { PRINTK("Set environment from HW MAC addr = \"%s\"\n", ethaddr); setenv ("ethaddr", ethaddr); - -#define DP_DATA 0x10 nic.data = nic.base + DP_DATA; - nic.tx_buf1 = 0x40; - nic.tx_buf2 = 0x48; - nic.rx_buf_start = 0x50; - nic.rx_buf_end = 0x80; + nic.tx_buf1 = START_PG; + nic.tx_buf2 = START_PG2; + nic.rx_buf_start = RX_START; + nic.rx_buf_end = RX_END; if (dp83902a_init() == false) return -1; + dp83902a_start(dev_addr); initialized=1; + return 0; } void eth_halt() { + PRINTK("### eth_halt\n"); if(initialized) dp83902a_stop(); @@ -920,7 +835,7 @@ int eth_send(volatile void *packet, int length) { pkey = -1; - dp83902a_send((unsigned char *) packet, length, 666); + dp83902a_send((u8 *) packet, length, 666); tmo = get_timer (0) + TOUT * CFG_HZ; while(1) { dp83902a_poll(); diff --git a/drivers/net/ne2000.h b/drivers/net/ne2000.h index c13d9f0..06e9a28 100644 --- a/drivers/net/ne2000.h +++ b/drivers/net/ne2000.h @@ -71,209 +71,113 @@ are GPL, so this is, of course, GPL. */ /* - ------------------------------------------------------------------------ - Macros for accessing DP registers - These can be overridden by the platform header -*/ - -#define DP_IN(_b_, _o_, _d_) (_d_) = *( (volatile unsigned char *) ((_b_)+(_o_))) -#define DP_OUT(_b_, _o_, _d_) *( (volatile unsigned char *) ((_b_)+(_o_))) = (_d_) - -#define DP_IN_DATA(_b_, _d_) (_d_) = *( (volatile unsigned char *) ((_b_))) -#define DP_OUT_DATA(_b_, _d_) *( (volatile unsigned char *) ((_b_))) = (_d_) - - -/* here is all the data */ - -#define cyg_uint8 unsigned char -#define cyg_uint16 unsigned short -#define bool int - -#define false 0 -#define true 1 - -#define CYGHWR_NS_DP83902A_PLF_BROKEN_TX_DMA 1 -#define CYGACC_CALL_IF_DELAY_US(X) my_udelay(X) - -typedef struct dp83902a_priv_data { - cyg_uint8* base; - cyg_uint8* data; - cyg_uint8* reset; - int tx_next; /* First free Tx page */ - int tx_int; /* Expecting interrupt from this buffer */ - int rx_next; /* First free Rx page */ - int tx1, tx2; /* Page numbers for Tx buffers */ - unsigned long tx1_key, tx2_key; /* Used to ack when packet sent */ - int tx1_len, tx2_len; - bool tx_started, running, hardwired_esa; - cyg_uint8 esa[6]; - void* plf_priv; - - /* Buffer allocation */ - int tx_buf1, tx_buf2; - int rx_buf_start, rx_buf_end; -} dp83902a_priv_data_t; - -/* - ------------------------------------------------------------------------ - Some forward declarations -*/ -static void dp83902a_poll(void); - -/* ------------------------------------------------------------------------ */ -/* Register offsets */ - -#define DP_CR 0x00 -#define DP_CLDA0 0x01 -#define DP_PSTART 0x01 /* write */ -#define DP_CLDA1 0x02 -#define DP_PSTOP 0x02 /* write */ -#define DP_BNDRY 0x03 -#define DP_TSR 0x04 -#define DP_TPSR 0x04 /* write */ -#define DP_NCR 0x05 -#define DP_TBCL 0x05 /* write */ -#define DP_FIFO 0x06 -#define DP_TBCH 0x06 /* write */ -#define DP_ISR 0x07 -#define DP_CRDA0 0x08 -#define DP_RSAL 0x08 /* write */ -#define DP_CRDA1 0x09 -#define DP_RSAH 0x09 /* write */ -#define DP_RBCL 0x0a /* write */ -#define DP_RBCH 0x0b /* write */ -#define DP_RSR 0x0c -#define DP_RCR 0x0c /* write */ -#define DP_FER 0x0d -#define DP_TCR 0x0d /* write */ -#define DP_CER 0x0e -#define DP_DCR 0x0e /* write */ -#define DP_MISSED 0x0f -#define DP_IMR 0x0f /* write */ -#define DP_DATAPORT 0x10 /* "eprom" data port */ - -#define DP_P1_CR 0x00 -#define DP_P1_PAR0 0x01 -#define DP_P1_PAR1 0x02 -#define DP_P1_PAR2 0x03 -#define DP_P1_PAR3 0x04 -#define DP_P1_PAR4 0x05 -#define DP_P1_PAR5 0x06 -#define DP_P1_CURP 0x07 -#define DP_P1_MAR0 0x08 -#define DP_P1_MAR1 0x09 -#define DP_P1_MAR2 0x0a -#define DP_P1_MAR3 0x0b -#define DP_P1_MAR4 0x0c -#define DP_P1_MAR5 0x0d -#define DP_P1_MAR6 0x0e -#define DP_P1_MAR7 0x0f - -#define DP_P2_CR 0x00 -#define DP_P2_PSTART 0x01 -#define DP_P2_CLDA0 0x01 /* write */ -#define DP_P2_PSTOP 0x02 -#define DP_P2_CLDA1 0x02 /* write */ -#define DP_P2_RNPP 0x03 -#define DP_P2_TPSR 0x04 -#define DP_P2_LNPP 0x05 -#define DP_P2_ACH 0x06 -#define DP_P2_ACL 0x07 -#define DP_P2_RCR 0x0c -#define DP_P2_TCR 0x0d -#define DP_P2_DCR 0x0e -#define DP_P2_IMR 0x0f - -/* Command register - common to all pages */ - -#define DP_CR_STOP 0x01 /* Stop: software reset */ -#define DP_CR_START 0x02 /* Start: initialize device */ -#define DP_CR_TXPKT 0x04 /* Transmit packet */ -#define DP_CR_RDMA 0x08 /* Read DMA (recv data from device) */ -#define DP_CR_WDMA 0x10 /* Write DMA (send data to device) */ -#define DP_CR_SEND 0x18 /* Send packet */ -#define DP_CR_NODMA 0x20 /* Remote (or no) DMA */ -#define DP_CR_PAGE0 0x00 /* Page select */ -#define DP_CR_PAGE1 0x40 -#define DP_CR_PAGE2 0x80 -#define DP_CR_PAGEMSK 0x3F /* Used to mask out page bits */ - -/* Data configuration register */ - -#define DP_DCR_WTS 0x01 /* 1=16 bit word transfers */ -#define DP_DCR_BOS 0x02 /* 1=Little Endian */ -#define DP_DCR_LAS 0x04 /* 1=Single 32 bit DMA mode */ -#define DP_DCR_LS 0x08 /* 1=normal mode, 0=loopback */ -#define DP_DCR_ARM 0x10 /* 0=no send command (program I/O) */ -#define DP_DCR_FIFO_1 0x00 /* FIFO threshold */ -#define DP_DCR_FIFO_2 0x20 -#define DP_DCR_FIFO_4 0x40 -#define DP_DCR_FIFO_6 0x60 - -#define DP_DCR_INIT (DP_DCR_LS|DP_DCR_FIFO_4) - -/* Interrupt status register */ - -#define DP_ISR_RxP 0x01 /* Packet received */ -#define DP_ISR_TxP 0x02 /* Packet transmitted */ -#define DP_ISR_RxE 0x04 /* Receive error */ -#define DP_ISR_TxE 0x08 /* Transmit error */ -#define DP_ISR_OFLW 0x10 /* Receive overflow */ -#define DP_ISR_CNT 0x20 /* Tally counters need emptying */ -#define DP_ISR_RDC 0x40 /* Remote DMA complete */ -#define DP_ISR_RESET 0x80 /* Device has reset (shutdown, error) */ - -/* Interrupt mask register */ - -#define DP_IMR_RxP 0x01 /* Packet received */ -#define DP_IMR_TxP 0x02 /* Packet transmitted */ -#define DP_IMR_RxE 0x04 /* Receive error */ -#define DP_IMR_TxE 0x08 /* Transmit error */ -#define DP_IMR_OFLW 0x10 /* Receive overflow */ -#define DP_IMR_CNT 0x20 /* Tall counters need emptying */ -#define DP_IMR_RDC 0x40 /* Remote DMA complete */ - -#define DP_IMR_All 0x3F /* Everything but remote DMA */ - -/* Receiver control register */ - -#define DP_RCR_SEP 0x01 /* Save bad(error) packets */ -#define DP_RCR_AR 0x02 /* Accept runt packets */ -#define DP_RCR_AB 0x04 /* Accept broadcast packets */ -#define DP_RCR_AM 0x08 /* Accept multicast packets */ -#define DP_RCR_PROM 0x10 /* Promiscuous mode */ -#define DP_RCR_MON 0x20 /* Monitor mode - 1=accept no packets */ - -/* Receiver status register */ - -#define DP_RSR_RxP 0x01 /* Packet received */ -#define DP_RSR_CRC 0x02 /* CRC error */ -#define DP_RSR_FRAME 0x04 /* Framing error */ -#define DP_RSR_FO 0x08 /* FIFO overrun */ -#define DP_RSR_MISS 0x10 /* Missed packet */ -#define DP_RSR_PHY 0x20 /* 0=pad match, 1=mad match */ -#define DP_RSR_DIS 0x40 /* Receiver disabled */ -#define DP_RSR_DFR 0x80 /* Receiver processing deferred */ - -/* Transmitter control register */ - -#define DP_TCR_NOCRC 0x01 /* 1=inhibit CRC */ -#define DP_TCR_NORMAL 0x00 /* Normal transmitter operation */ -#define DP_TCR_LOCAL 0x02 /* Internal NIC loopback */ -#define DP_TCR_INLOOP 0x04 /* Full internal loopback */ -#define DP_TCR_OUTLOOP 0x08 /* External loopback */ -#define DP_TCR_ATD 0x10 /* Auto transmit disable */ -#define DP_TCR_OFFSET 0x20 /* Collision offset adjust */ - -/* Transmit status register */ - -#define DP_TSR_TxP 0x01 /* Packet transmitted */ -#define DP_TSR_COL 0x04 /* Collision (at least one) */ -#define DP_TSR_ABT 0x08 /* Aborted because of too many collisions */ -#define DP_TSR_CRS 0x10 /* Lost carrier */ -#define DP_TSR_FU 0x20 /* FIFO underrun */ -#define DP_TSR_CDH 0x40 /* Collision Detect Heartbeat */ -#define DP_TSR_OWC 0x80 /* Collision outside normal window */ - -#define IEEE_8023_MAX_FRAME 1518 /* Largest possible ethernet frame */ -#define IEEE_8023_MIN_FRAME 64 /* Smallest possible ethernet frame */ + * NE2000 support header file. + * Created by Nobuhiro Iwamatsu <iwamatsu(a)nigauri.org> + */ + +#ifndef __DRIVERS_NE2000_H__ +#define __DRIVERS_NE2000_H__ + +/* Enable NE2000 basic init function */ +#define NE2000_BASIC_INIT + +#define DP_DATA 0x10 +#define START_PG 0x50 /* First page of TX buffer */ +#define STOP_PG 0x80 /* Last page +1 of RX ring */ + +#define RX_START 0x50 +#define RX_END 0x80 + +#define DP_IN(_b_, _o_, _d_) (_d_) = *( (vu_char *) ((_b_)+(_o_))) +#define DP_OUT(_b_, _o_, _d_) *( (vu_char *) ((_b_)+(_o_))) = (_d_) +#define DP_IN_DATA(_b_, _d_) (_d_) = *( (vu_char *) ((_b_))) +#define DP_OUT_DATA(_b_, _d_) *( (vu_char *) ((_b_))) = (_d_) + +static void pcnet_reset_8390(void) +{ + int i, r; + + PRINTK("nic base is %lx\n", nic_base); + + n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); + PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); + n2k_outb(E8390_NODMA+E8390_PAGE1+E8390_STOP, E8390_CMD); + PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); + n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); + PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); + n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); + + n2k_outb(n2k_inb(PCNET_RESET), PCNET_RESET); + + for (i = 0; i < 100; i++) { + if ((r = (n2k_inb(EN0_ISR) & ENISR_RESET)) != 0) + break; + PRINTK("got %x in reset\n", r); + udelay(100); + } + n2k_outb(ENISR_RESET, EN0_ISR); /* Ack intr. */ + + if (i == 100) + printf("pcnet_reset_8390() did not complete.\n"); +} /* pcnet_reset_8390 */ + +int get_prom(u8* mac_addr) +{ + u8 prom[32]; + int i, j; + struct { + u_char value, offset; + } program_seq[] = { + {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/ + {0x48, EN0_DCFG}, /* Set byte-wide (0x48) access. */ + {0x00, EN0_RCNTLO}, /* Clear the count regs. */ + {0x00, EN0_RCNTHI}, + {0x00, EN0_IMR}, /* Mask completion irq. */ + {0xFF, EN0_ISR}, + {E8390_RXOFF, EN0_RXCR}, /* 0x20 Set to monitor */ + {E8390_TXOFF, EN0_TXCR}, /* 0x02 and loopback mode. */ + {32, EN0_RCNTLO}, + {0x00, EN0_RCNTHI}, + {0x00, EN0_RSARLO}, /* DMA starting at 0x0000. */ + {0x00, EN0_RSARHI}, + {E8390_RREAD+E8390_START, E8390_CMD}, + }; + + PRINTK("trying to get MAC via prom reading\n"); + + pcnet_reset_8390(); + + mdelay(10); + + for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++) + n2k_outb(program_seq[i].value, program_seq[i].offset); + + PRINTK("PROM:"); + for (i = 0; i < 32; i++) { + prom[i] = n2k_inb(PCNET_DATAPORT); + PRINTK(" %02x", prom[i]); + } + PRINTK("\n"); + for (i = 0; i < NR_INFO; i++) { + if ((prom[0] == hw_info[i].a0) && + (prom[2] == hw_info[i].a1) && + (prom[4] == hw_info[i].a2)) { + PRINTK("matched board %d\n", i); + break; + } + } + if ((i < NR_INFO) || ((prom[28] == 0x57) && (prom[30] == 0x57))) { + PRINTK("on exit i is %d/%ld\n", i, NR_INFO); + PRINTK("MAC address is "); + for (j = 0; j < 6; j++){ + mac_addr[j] = prom[j<<1]; + PRINTK("%02x:",mac_addr[i]); + } + PRINTK("\n"); + return (i < NR_INFO) ? i : 0; + } + return NULL; +} + + +#endif /* __DRIVERS_NE2000_H__ */ diff --git a/drivers/net/ne2000_base.h b/drivers/net/ne2000_base.h new file mode 100644 index 0000000..1badf62 --- /dev/null +++ b/drivers/net/ne2000_base.h @@ -0,0 +1,282 @@ +/* +Ported to U-Boot by Christian Pellegrin <chri(a)ascensit.com> + +Based on sources from the Linux kernel (pcnet_cs.c, 8390.h) and +eCOS(if_dp83902a.c, if_dp83902a.h). Both of these 2 wonderful world +are GPL, so this is, of course, GPL. + + +========================================================================== + + dev/dp83902a.h + + National Semiconductor DP83902a ethernet chip + +========================================================================== +####ECOSGPLCOPYRIGHTBEGIN#### + ------------------------------------------- + This file is part of eCos, the Embedded Configurable Operating System. + Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc. + + eCos is free software; you can redistribute it and/or modify it under + the terms of the GNU General Public License as published by the Free + Software Foundation; either version 2 or (at your option) any later version. + + eCos is distributed in the hope that it will be useful, but WITHOUT ANY + WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + for more details. + + You should have received a copy of the GNU General Public License along + with eCos; if not, write to the Free Software Foundation, Inc., + 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA. + + As a special exception, if other files instantiate templates or use macros + or inline functions from this file, or you compile this file and link it + with other works to produce a work based on this file, this file does not + by itself cause the resulting work to be covered by the GNU General Public + License. However the source code for this file must still be made available + in accordance with section (3) of the GNU General Public License. + + This exception does not invalidate any other reasons why a work based on + this file might be covered by the GNU General Public License. + + Alternative licenses for eCos may be arranged by contacting Red Hat, Inc. + at http://sources.redhat.com/ecos/ecos-license/ + ------------------------------------------- +####ECOSGPLCOPYRIGHTEND#### +####BSDCOPYRIGHTBEGIN#### + + ------------------------------------------- + + Portions of this software may have been derived from OpenBSD or other sources, + and are covered by the appropriate copyright disclaimers included herein. + + ------------------------------------------- + +####BSDCOPYRIGHTEND#### +========================================================================== +#####DESCRIPTIONBEGIN#### + + Author(s): gthomas + Contributors: gthomas, jskov + Date: 2001-06-13 + Purpose: + Description: + +####DESCRIPTIONEND#### + +========================================================================== + +*/ + +/* + ------------------------------------------------------------------------ + Macros for accessing DP registers + These can be overridden by the platform header +*/ + +#define bool int + +#define false 0 +#define true 1 + +/* timeout for tx/rx in s */ +#define TOUT 5 +/* Ether MAC address size */ +#define ETHER_ADDR_LEN 6 + + +#define CYGHWR_NS_DP83902A_PLF_BROKEN_TX_DMA 1 +#define CYGACC_CALL_IF_DELAY_US(X) udelay(X) + +/* H/W infomation struct */ +typedef struct hw_info_t { + u32 offset; + u8 a0, a1, a2; + u32 flags; +} hw_info_t; + +typedef struct dp83902a_priv_data { + u8* base; + u8* data; + u8* reset; + int tx_next; /* First free Tx page */ + int tx_int; /* Expecting interrupt from this buffer */ + int rx_next; /* First free Rx page */ + int tx1, tx2; /* Page numbers for Tx buffers */ + u32 tx1_key, tx2_key; /* Used to ack when packet sent */ + int tx1_len, tx2_len; + bool tx_started, running, hardwired_esa; + u8 esa[6]; + void* plf_priv; + + /* Buffer allocation */ + int tx_buf1, tx_buf2; + int rx_buf_start, rx_buf_end; +} dp83902a_priv_data_t; + +/* + ------------------------------------------------------------------------ + Some forward declarations +*/ +int get_prom( u8* mac_addr); +static void dp83902a_poll(void); + +/* ------------------------------------------------------------------------ */ +/* Register offsets */ + +#define DP_CR 0x00 +#define DP_CLDA0 0x01 +#define DP_PSTART 0x01 /* write */ +#define DP_CLDA1 0x02 +#define DP_PSTOP 0x02 /* write */ +#define DP_BNDRY 0x03 +#define DP_TSR 0x04 +#define DP_TPSR 0x04 /* write */ +#define DP_NCR 0x05 +#define DP_TBCL 0x05 /* write */ +#define DP_FIFO 0x06 +#define DP_TBCH 0x06 /* write */ +#define DP_ISR 0x07 +#define DP_CRDA0 0x08 +#define DP_RSAL 0x08 /* write */ +#define DP_CRDA1 0x09 +#define DP_RSAH 0x09 /* write */ +#define DP_RBCL 0x0a /* write */ +#define DP_RBCH 0x0b /* write */ +#define DP_RSR 0x0c +#define DP_RCR 0x0c /* write */ +#define DP_FER 0x0d +#define DP_TCR 0x0d /* write */ +#define DP_CER 0x0e +#define DP_DCR 0x0e /* write */ +#define DP_MISSED 0x0f +#define DP_IMR 0x0f /* write */ +#define DP_DATAPORT 0x10 /* "eprom" data port */ + +#define DP_P1_CR 0x00 +#define DP_P1_PAR0 0x01 +#define DP_P1_PAR1 0x02 +#define DP_P1_PAR2 0x03 +#define DP_P1_PAR3 0x04 +#define DP_P1_PAR4 0x05 +#define DP_P1_PAR5 0x06 +#define DP_P1_CURP 0x07 +#define DP_P1_MAR0 0x08 +#define DP_P1_MAR1 0x09 +#define DP_P1_MAR2 0x0a +#define DP_P1_MAR3 0x0b +#define DP_P1_MAR4 0x0c +#define DP_P1_MAR5 0x0d +#define DP_P1_MAR6 0x0e +#define DP_P1_MAR7 0x0f + +#define DP_P2_CR 0x00 +#define DP_P2_PSTART 0x01 +#define DP_P2_CLDA0 0x01 /* write */ +#define DP_P2_PSTOP 0x02 +#define DP_P2_CLDA1 0x02 /* write */ +#define DP_P2_RNPP 0x03 +#define DP_P2_TPSR 0x04 +#define DP_P2_LNPP 0x05 +#define DP_P2_ACH 0x06 +#define DP_P2_ACL 0x07 +#define DP_P2_RCR 0x0c +#define DP_P2_TCR 0x0d +#define DP_P2_DCR 0x0e +#define DP_P2_IMR 0x0f + +/* Command register - common to all pages */ + +#define DP_CR_STOP 0x01 /* Stop: software reset */ +#define DP_CR_START 0x02 /* Start: initialize device */ +#define DP_CR_TXPKT 0x04 /* Transmit packet */ +#define DP_CR_RDMA 0x08 /* Read DMA (recv data from device) */ +#define DP_CR_WDMA 0x10 /* Write DMA (send data to device) */ +#define DP_CR_SEND 0x18 /* Send packet */ +#define DP_CR_NODMA 0x20 /* Remote (or no) DMA */ +#define DP_CR_PAGE0 0x00 /* Page select */ +#define DP_CR_PAGE1 0x40 +#define DP_CR_PAGE2 0x80 +#define DP_CR_PAGEMSK 0x3F /* Used to mask out page bits */ + +/* Data configuration register */ + +#define DP_DCR_WTS 0x01 /* 1=16 bit word transfers */ +#define DP_DCR_BOS 0x02 /* 1=Little Endian */ +#define DP_DCR_LAS 0x04 /* 1=Single 32 bit DMA mode */ +#define DP_DCR_LS 0x08 /* 1=normal mode, 0=loopback */ +#define DP_DCR_ARM 0x10 /* 0=no send command (program I/O) */ +#define DP_DCR_FIFO_1 0x00 /* FIFO threshold */ +#define DP_DCR_FIFO_2 0x20 +#define DP_DCR_FIFO_4 0x40 +#define DP_DCR_FIFO_6 0x60 + +#define DP_DCR_INIT (DP_DCR_LS|DP_DCR_FIFO_4) + +/* Interrupt status register */ + +#define DP_ISR_RxP 0x01 /* Packet received */ +#define DP_ISR_TxP 0x02 /* Packet transmitted */ +#define DP_ISR_RxE 0x04 /* Receive error */ +#define DP_ISR_TxE 0x08 /* Transmit error */ +#define DP_ISR_OFLW 0x10 /* Receive overflow */ +#define DP_ISR_CNT 0x20 /* Tally counters need emptying */ +#define DP_ISR_RDC 0x40 /* Remote DMA complete */ +#define DP_ISR_RESET 0x80 /* Device has reset (shutdown, error) */ + +/* Interrupt mask register */ + +#define DP_IMR_RxP 0x01 /* Packet received */ +#define DP_IMR_TxP 0x02 /* Packet transmitted */ +#define DP_IMR_RxE 0x04 /* Receive error */ +#define DP_IMR_TxE 0x08 /* Transmit error */ +#define DP_IMR_OFLW 0x10 /* Receive overflow */ +#define DP_IMR_CNT 0x20 /* Tall counters need emptying */ +#define DP_IMR_RDC 0x40 /* Remote DMA complete */ + +#define DP_IMR_All 0x3F /* Everything but remote DMA */ + +/* Receiver control register */ + +#define DP_RCR_SEP 0x01 /* Save bad(error) packets */ +#define DP_RCR_AR 0x02 /* Accept runt packets */ +#define DP_RCR_AB 0x04 /* Accept broadcast packets */ +#define DP_RCR_AM 0x08 /* Accept multicast packets */ +#define DP_RCR_PROM 0x10 /* Promiscuous mode */ +#define DP_RCR_MON 0x20 /* Monitor mode - 1=accept no packets */ + +/* Receiver status register */ + +#define DP_RSR_RxP 0x01 /* Packet received */ +#define DP_RSR_CRC 0x02 /* CRC error */ +#define DP_RSR_FRAME 0x04 /* Framing error */ +#define DP_RSR_FO 0x08 /* FIFO overrun */ +#define DP_RSR_MISS 0x10 /* Missed packet */ +#define DP_RSR_PHY 0x20 /* 0=pad match, 1=mad match */ +#define DP_RSR_DIS 0x40 /* Receiver disabled */ +#define DP_RSR_DFR 0x80 /* Receiver processing deferred */ + +/* Transmitter control register */ + +#define DP_TCR_NOCRC 0x01 /* 1=inhibit CRC */ +#define DP_TCR_NORMAL 0x00 /* Normal transmitter operation */ +#define DP_TCR_LOCAL 0x02 /* Internal NIC loopback */ +#define DP_TCR_INLOOP 0x04 /* Full internal loopback */ +#define DP_TCR_OUTLOOP 0x08 /* External loopback */ +#define DP_TCR_ATD 0x10 /* Auto transmit disable */ +#define DP_TCR_OFFSET 0x20 /* Collision offset adjust */ + +/* Transmit status register */ + +#define DP_TSR_TxP 0x01 /* Packet transmitted */ +#define DP_TSR_COL 0x04 /* Collision (at least one) */ +#define DP_TSR_ABT 0x08 /* Aborted because of too many collisions */ +#define DP_TSR_CRS 0x10 /* Lost carrier */ +#define DP_TSR_FU 0x20 /* FIFO underrun */ +#define DP_TSR_CDH 0x40 /* Collision Detect Heartbeat */ +#define DP_TSR_OWC 0x80 /* Collision outside normal window */ + +#define IEEE_8023_MAX_FRAME 1518 /* Largest possible ethernet frame */ +#define IEEE_8023_MIN_FRAME 64 /* Smallest possible ethernet frame */ --

4 4

[U-Boot-Users] DDR-II @ MPC8343A
by Andre Schwarz 25 Mar '08

25 Mar '08

All, has anyone set up the DDR-II controller on a Freescale MPC8343A without ? As far as I can see there are only DDR-I boards from Freescale. Are there any patches not yet posted to handle this ? regards, Andre Schwarz Matrix Vision MATRIX VISION GmbH, Talstraße 16, DE-71570 Oppenweiler - Registergericht: Amtsgericht Stuttgart, HRB 271090 Geschäftsführer: Gerhard Thullner, Werner Armingeon, Uwe Furtner

3 8

[U-Boot-Users] [PATCH] smc91111: use SSYNC() rather than asm(ssync) for Blackfin
by Mike Frysinger 25 Mar '08

25 Mar '08

Since the "ssync" instruction may have hardware anomalies associated with it, have the smc91111 driver use the SSYNC macro rather than invoking it directly. We workaround all the anomalies via this macro. Signed-off-by: Mike Frysinger <vapier(a)gentoo.org> --- drivers/net/smc91111.h | 4 ++-- 1 files changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/smc91111.h b/drivers/net/smc91111.h index d03cbc3..8dcbb3e 100644 --- a/drivers/net/smc91111.h +++ b/drivers/net/smc91111.h @@ -186,7 +186,7 @@ typedef unsigned long int dword; #ifdef CONFIG_ADNPESC1 #define SMC_inw(r) (*((volatile word *)(SMC_BASE_ADDRESS+((r)<<1)))) #elif CONFIG_BLACKFIN -#define SMC_inw(r) ({ word __v = (*((volatile word *)(SMC_BASE_ADDRESS+(r)))); asm("ssync;"); __v;}) +#define SMC_inw(r) ({ word __v = (*((volatile word *)(SMC_BASE_ADDRESS+(r)))); SSYNC(); __v;}) #else #define SMC_inw(r) (*((volatile word *)(SMC_BASE_ADDRESS+(r)))) #endif @@ -195,7 +195,7 @@ typedef unsigned long int dword; #ifdef CONFIG_ADNPESC1 #define SMC_outw(d,r) (*((volatile word *)(SMC_BASE_ADDRESS+((r)<<1))) = d) #elif CONFIG_BLACKFIN -#define SMC_outw(d,r) {(*((volatile word *)(SMC_BASE_ADDRESS+(r))) = d);asm("ssync;");} +#define SMC_outw(d,r) {(*((volatile word *)(SMC_BASE_ADDRESS+(r))) = d); SSYNC();} #else #define SMC_outw(d,r) (*((volatile word *)(SMC_BASE_ADDRESS+(r))) = d) #endif -- 1.5.4.2

2 1

[U-Boot-Users] [PATCH 2/2] 8xx: Update of support on 8xx
by Bryan O'Donoghue 25 Mar '08

25 Mar '08

Resubmit- previous patch mangled by milter @ 80 characters. This patch does some shifting around of OF support on 8xx. Signed-off-by: Bryan O'Donoghue <bodonoghue(a)codehermit.ie> --- diff --git a/cpu/mpc8xx/Makefile b/cpu/mpc8xx/Makefile index 223b30c..dbdc2e0 100644 --- a/cpu/mpc8xx/Makefile +++ b/cpu/mpc8xx/Makefile @@ -29,7 +29,7 @@ LIB = $(obj)lib$(CPU).a START = start.o kgdb.o COBJS = bedbug_860.o commproc.o cpu.o cpu_init.o \ - fec.o i2c.o interrupts.o lcd.o scc.o \ + fec.o fdt.o i2c.o interrupts.o lcd.o scc.o \ serial.o speed.o spi.o \ traps.o upatch.o video.o SOBJS = plprcr_write.o diff --git a/cpu/mpc8xx/cpu.c b/cpu/mpc8xx/cpu.c index c878352..a86598e 100644 --- a/cpu/mpc8xx/cpu.c +++ b/cpu/mpc8xx/cpu.c @@ -637,14 +637,3 @@ void reset_8xx_watchdog (volatile immap_t * immr) #endif /* CONFIG_WATCHDOG */ -/* ------------------------------------------------------------------------- */ -#if defined(CONFIG_OF_LIBFDT) -void ft_cpu_setup (void *blob, bd_t *bd) -{ - char * cpu_path = "/cpus/" OF_CPU; - - do_fixup_by_path_u32(blob, cpu_path, "bus-frequency", bd->bi_busfreq, 1); - do_fixup_by_path_u32(blob, cpu_path, "timebase-frequency", OF_TBCLK, 1); - do_fixup_by_path_u32(blob, cpu_path, "clock-frequency", bd->bi_intfreq, 1); -} -#endif /* CONFIG_OF_LIBFDT */ diff --git a/cpu/mpc8xx/fdt.c b/cpu/mpc8xx/fdt.c new file mode 100644 index 0000000..567094a --- /dev/null +++ b/cpu/mpc8xx/fdt.c @@ -0,0 +1,46 @@ +/* + * Copyright 2008 (C) Bryan O'Donoghue + * + * Code copied & edited from Freescale mpc85xx stuff. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <libfdt.h> +#include <fdt_support.h> + +DECLARE_GLOBAL_DATA_PTR; + +void ft_cpu_setup(void *blob, bd_t *bd) +{ + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "timebase-frequency", get_tbclk(), 1); + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "bus-frequency", bd->bi_busfreq, 1); + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "clock-frequency", bd->bi_intfreq, 1); + do_fixup_by_compat_u32(blob, "fsl,cpm-brg", "clock-frequency", + gd->brg_clk, 1); + + /* Fixup ethernet MAC addresses */ + fdt_fixup_ethernet(blob, bd); + + fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize); +} diff --git a/cpu/mpc8xx/speed.c b/cpu/mpc8xx/speed.c index 11b0893..070babc 100644 --- a/cpu/mpc8xx/speed.c +++ b/cpu/mpc8xx/speed.c @@ -174,6 +174,27 @@ unsigned long measure_gclk(void) #endif +void get_brgclk(uint sccr) +{ + uint divider = 0; + + switch((sccr&SCCR_DFBRG11)>>11){ + case 0: + divider = 1; + break; + case 1: + divider = 4; + break; + case 2: + divider = 16; + break; + case 3: + divider = 64; + break; + } + gd->brg_clk = gd->cpu_clk/divider; +} + #if !defined(CONFIG_8xx_CPUCLK_DEFAULT) /* @@ -223,6 +244,8 @@ int get_clocks (void) gd->bus_clk = gd->cpu_clk / 2; } + get_brgclk(sccr); + return (0); } @@ -254,6 +277,8 @@ int get_clocks_866 (void) gd->cpu_clk = measure_gclk (); #endif + get_brgclk(immr->im_clkrst.car_sccr); + /* if cpu clock <= 66 MHz then set bus division factor to 1, * otherwise set it to 2 */ diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h index f9a3d92..789e116 100644 --- a/include/asm-ppc/global_data.h +++ b/include/asm-ppc/global_data.h @@ -40,8 +40,11 @@ typedef struct global_data { bd_t *bd; unsigned long flags; unsigned long baudrate; - unsigned long cpu_clk; /* CPU clock in Hz! */ + unsigned long cpu_clk; /* CPU clock in Hz! */ unsigned long bus_clk; +#if defined(CONFIG_8xx) + unsigned long brg_clk; +#endif #if defined(CONFIG_CPM2) /* There are many clocks on the MPC8260 - see page 9-5 */ unsigned long vco_out;

2 2

[U-Boot-Users] [PATCH] ppc: Allow boards to specify how much memory they can map
by Kumar Gala 25 Mar '08

25 Mar '08

For historical reasons we limited the stack to 256M because some boards could only map that much via BATS. However newer boards are capable of mapping more memory (for example 85xx is capble of doing up to 2G). Signed-off-by: Kumar Gala <galak(a)kernel.crashing.org> --- lib_ppc/board.c | 7 ++++++- 1 files changed, 6 insertions(+), 1 deletions(-) diff --git a/lib_ppc/board.c b/lib_ppc/board.c index 45d1328..8c9f6e6 100644 --- a/lib_ppc/board.c +++ b/lib_ppc/board.c @@ -419,12 +419,17 @@ void board_init_f (ulong bootflag) */ len = (ulong)&_end - CFG_MONITOR_BASE; +#ifndef CONFIG_MAX_MEM_MAPPED +#define CONFIG_MAX_MEM_MAPPED (256 << 20) +#endif + #ifndef CONFIG_VERY_BIG_RAM addr = CFG_SDRAM_BASE + gd->ram_size; #else /* only allow stack below 256M */ addr = CFG_SDRAM_BASE + - (gd->ram_size > 256 << 20) ? 256 << 20 : gd->ram_size; + (gd->ram_size > CONFIG_MAX_MEM_MAPPED) ? + CONFIG_MAX_MEM_MAPPED : gd->ram_size; #endif #ifdef CONFIG_LOGBUFFER -- 1.5.3.8

2 1

[U-Boot-Users] [PATCH 3/3] 8xx: Update and extend 8xx fdt support - resubmit
by Bryan O'Donoghue 25 Mar '08

25 Mar '08

Attached patch updates the 8xx fdt support for 8xx. As pointed out by Scott Wood - OF_CPU, OF_TBCLK aren't needed and get_tbclk() should be used instead of bd->bi_busfreq. Signed-off-by: Bryan O'Donoghue <bodonoghue(a)codehermit.ie> --- diff --git a/cpu/mpc8xx/fdt.c b/cpu/mpc8xx/fdt.c new file mode 100644 index 0000000..567094a --- /dev/null +++ b/cpu/mpc8xx/fdt.c @@ -0,0 +1,46 @@ +/* + * Copyright 2008 (C) Bryan O'Donoghue + * + * Code copied & edited from Freescale mpc85xx stuff. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <libfdt.h> +#include <fdt_support.h> + +DECLARE_GLOBAL_DATA_PTR; + +void ft_cpu_setup(void *blob, bd_t *bd) +{ + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "timebase-frequency", get_tbclk(), 1); + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "bus-frequency", bd->bi_busfreq, 1); + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "clock-frequency", bd->bi_intfreq, 1); + do_fixup_by_compat_u32(blob, "fsl,cpm-brg", "clock-frequency", + gd->brg_clk, 1); + + /* Fixup ethernet MAC addresses */ + fdt_fixup_ethernet(blob, bd); + + fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize); +} diff --git a/cpu/mpc8xx/Makefile b/cpu/mpc8xx/Makefile index 223b30c..dbdc2e0 100644 --- a/cpu/mpc8xx/Makefile +++ b/cpu/mpc8xx/Makefile @@ -29,7 +29,7 @@ LIB = $(obj)lib$(CPU).a START = start.o kgdb.o COBJS = bedbug_860.o commproc.o cpu.o cpu_init.o \ - fec.o i2c.o interrupts.o lcd.o scc.o \ + fec.o fdt.o i2c.o interrupts.o lcd.o scc.o \ serial.o speed.o spi.o \ traps.o upatch.o video.o SOBJS = plprcr_write.o diff --git a/cpu/mpc8xx/cpu.c b/cpu/mpc8xx/cpu.c index c878352..a86598e 100644 --- a/cpu/mpc8xx/cpu.c +++ b/cpu/mpc8xx/cpu.c @@ -637,14 +637,3 @@ void reset_8xx_watchdog (volatile immap_t * immr) #endif /* CONFIG_WATCHDOG */ -/* ------------------------------------------------------------------------- */ -#if defined(CONFIG_OF_LIBFDT) -void ft_cpu_setup (void *blob, bd_t *bd) -{ - char * cpu_path = "/cpus/" OF_CPU; - - do_fixup_by_path_u32(blob, cpu_path, "bus-frequency", bd->bi_busfreq, 1); - do_fixup_by_path_u32(blob, cpu_path, "timebase-frequency", OF_TBCLK, 1); - do_fixup_by_path_u32(blob, cpu_path, "clock-frequency", bd->bi_intfreq, 1); -} -#endif /* CONFIG_OF_LIBFDT */ diff --git a/cpu/mpc8xx/speed.c b/cpu/mpc8xx/speed.c index 11b0893..070babc 100644 --- a/cpu/mpc8xx/speed.c +++ b/cpu/mpc8xx/speed.c @@ -174,6 +174,27 @@ unsigned long measure_gclk(void) #endif +void get_brgclk(uint sccr) +{ + uint divider = 0; + + switch((sccr&SCCR_DFBRG11)>>11){ + case 0: + divider = 1; + break; + case 1: + divider = 4; + break; + case 2: + divider = 16; + break; + case 3: + divider = 64; + break; + } + gd->brg_clk = gd->cpu_clk/divider; +} + #if !defined(CONFIG_8xx_CPUCLK_DEFAULT) /* @@ -223,6 +244,8 @@ int get_clocks (void) gd->bus_clk = gd->cpu_clk / 2; } + get_brgclk(sccr); + return (0); } @@ -254,6 +277,8 @@ int get_clocks_866 (void) gd->cpu_clk = measure_gclk (); #endif + get_brgclk(immr->im_clkrst.car_sccr); + /* if cpu clock <= 66 MHz then set bus division factor to 1, * otherwise set it to 2 */ diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h index aa6384c..47c49ea 100644 --- a/include/asm-ppc/global_data.h +++ b/include/asm-ppc/global_data.h @@ -42,6 +42,9 @@ typedef struct global_data { unsigned long baudrate; unsigned long cpu_clk; /* CPU clock in Hz! */ unsigned long bus_clk; +#if defined(CONFIG_8xx) + unsigned long brg_clk; +#endif #if defined(CONFIG_CPM2) /* There are many clocks on the MPC8260 - see page 9-5 */ unsigned long vco_out;

2 1