April 2007 - U-Boot

[U-Boot-Users] [PATCH 3/4] Modify MPC85xx CPU files for MPC8544DS board port.
by Jon Loeliger 11 Apr '07

11 Apr '07

Recognize new SVR values, add a few register definitions, and add a few new sysclk cases. Make some DDR biasing configurations apply only to 8548. Allow for skipping DDR initialization if it is already done. Signed-off-by: Ed Swarthout <Ed.Swarthout(a)freescale.com> Signed-off-by: Jon Loeliger <jdl(a)freescale.com> --- cpu/mpc85xx/cpu.c | 33 ++++++++++++++++------ cpu/mpc85xx/spd_sdram.c | 68 +++++++++++++++++++++++++++++++++++++++++----- cpu/mpc85xx/speed.c | 27 +++++++++++++++--- 3 files changed, 106 insertions(+), 22 deletions(-) diff --git a/cpu/mpc85xx/cpu.c b/cpu/mpc85xx/cpu.c index 0507c47..660379c 100644 --- a/cpu/mpc85xx/cpu.c +++ b/cpu/mpc85xx/cpu.c @@ -1,5 +1,5 @@ /* - * Copyright 2004 Freescale Semiconductor. + * Copyright 2004,2007 Freescale Semiconductor, Inc. * (C) Copyright 2002, 2003 Motorola Inc. * Xianghua Xiao (X.Xiao(a)motorola.com) * @@ -70,6 +70,12 @@ int checkcpu (void) case SVR_8548_E: puts("8548_E"); break; + case SVR_8544: + puts("8544"); + break; + case SVR_8544_E: + puts("8544_E"); + break; default: puts("Unknown"); break; @@ -112,7 +118,7 @@ int checkcpu (void) #endif clkdiv = lcrr & 0x0f; if (clkdiv == 2 || clkdiv == 4 || clkdiv == 8) { -#ifdef CONFIG_MPC8548 +#if defined(CONFIG_MPC8548) || defined(CONFIG_MPC8544) /* * Yes, the entire PQ38 family use the same * bit-representation for twice the clock divider values. @@ -183,9 +189,9 @@ reset_85xx_watchdog(void) * Clear TSR(WIS) bit by writing 1 */ unsigned long val; - val = mfspr(tsr); - val |= 0x40000000; - mtspr(tsr, val); + val = mfspr(SPRN_TSR); + val |= TSR_WIS; + mtspr(SPRN_TSR, val); } #endif /* CONFIG_WATCHDOG */ @@ -196,6 +202,7 @@ void dma_init(void) { dma->satr0 = 0x02c40000; dma->datr0 = 0x02c40000; + dma->sr0 = 0xfffffff; /* clear any errors */ asm("sync; isync; msync"); return; } @@ -210,6 +217,10 @@ uint dma_check(void) { status = dma->sr0; } + /* clear MR0[CS] channel start bit */ + dma->mr0 &= 0x00000001; + asm("sync;isync;msync"); + if (status != 0) { printf ("DMA Error: status = %x\n", status); } @@ -254,22 +265,26 @@ ft_cpu_setup(void *blob, bd_t *bd) *p = cpu_to_be32(clock); #if defined(CONFIG_MPC85XX_TSEC1) - p = ft_get_prop(blob, "/" OF_SOC "/ethernet@24000/mac-address", &len); + p = ft_get_prop(blob, "/" OF_SOC "/ethernet@24000/local-mac-address", &len); + if (p != NULL) memcpy(p, bd->bi_enetaddr, 6); #endif #if defined(CONFIG_HAS_ETH1) - p = ft_get_prop(blob, "/" OF_SOC "/ethernet@25000/mac-address", &len); + p = ft_get_prop(blob, "/" OF_SOC "/ethernet@25000/local-mac-address", &len); + if (p != NULL) memcpy(p, bd->bi_enet1addr, 6); #endif #if defined(CONFIG_HAS_ETH2) - p = ft_get_prop(blob, "/" OF_SOC "/ethernet@26000/mac-address", &len); + p = ft_get_prop(blob, "/" OF_SOC "/ethernet@26000/local-mac-address", &len); + if (p != NULL) memcpy(p, bd->bi_enet2addr, 6); #endif #if defined(CONFIG_HAS_ETH3) - p = ft_get_prop(blob, "/" OF_SOC "/ethernet@27000/mac-address", &len); + p = ft_get_prop(blob, "/" OF_SOC "/ethernet@27000/local-mac-address", &len); + if (p != NULL) memcpy(p, bd->bi_enet3addr, 6); #endif diff --git a/cpu/mpc85xx/spd_sdram.c b/cpu/mpc85xx/spd_sdram.c index 6da5367..45e7879 100644 --- a/cpu/mpc85xx/spd_sdram.c +++ b/cpu/mpc85xx/spd_sdram.c @@ -1,5 +1,5 @@ /* - * Copyright 2004 Freescale Semiconductor. + * Copyright 2004, 2007 Freescale Semiconductor, Inc. * (C) Copyright 2003 Motorola Inc. * Xianghua Xiao (X.Xiao(a)motorola.com) * @@ -173,7 +173,6 @@ spd_sdram(void) { volatile immap_t *immap = (immap_t *)CFG_IMMR; volatile ccsr_ddr_t *ddr = &immap->im_ddr; - volatile ccsr_gur_t *gur = &immap->im_gur; spd_eeprom_t spd; unsigned int n_ranks; unsigned int rank_density; @@ -189,7 +188,7 @@ spd_sdram(void) unsigned int max_data_rate, effective_data_rate; unsigned int busfreq; unsigned sdram_cfg; - unsigned int memsize; + unsigned int memsize=0; unsigned char caslat, caslat_ctrl; unsigned int trfc, trfc_clk, trfc_low, trfc_high; unsigned int trcd_clk; @@ -204,6 +203,46 @@ spd_sdram(void) unsigned int mode_caslat; unsigned char sdram_type; unsigned char d_init; + unsigned int bnds; + + /* + * Skip configuration if already configured. + * memsize is determined from last configured chip select. + */ + if (ddr->cs0_config & 0x80000000) { + debug(" cs0 already configured, bnds=%x\n",ddr->cs0_bnds); + bnds = 0xfff & ddr->cs0_bnds; + if (bnds < 0xff) { /* do not add if at top of 4G */ + memsize = (bnds + 1) << 4; + } + } + if (ddr->cs1_config & 0x80000000) { + debug(" cs1 already configured, bnds=%x\n",ddr->cs1_bnds); + bnds = 0xfff & ddr->cs1_bnds; + if (bnds < 0xff) { /* do not add if at top of 4G */ + memsize = (bnds + 1) << 4; /* assume ordered bnds */ + } + } + if (ddr->cs2_config & 0x80000000) { + debug(" cs2 already configured, bnds=%x\n",ddr->cs2_bnds); + bnds = 0xfff & ddr->cs2_bnds; + if (bnds < 0xff) { /* do not add if at top of 4G */ + memsize = (bnds + 1) << 4; + } + } + if (ddr->cs3_config & 0x80000000) { + debug(" cs3 already configured, bnds=%x\n",ddr->cs3_bnds); + bnds = 0xfff & ddr->cs3_bnds; + if (bnds < 0xff) { /* do not add if at top of 4G */ + memsize = (bnds + 1) << 4; + } + } + + if (memsize) { + printf(" Reusing current %dMB configuration\n",memsize); + memsize = setup_laws_and_tlbs(memsize); + return memsize << 20; + } /* * Read SPD information. @@ -262,15 +301,19 @@ spd_sdram(void) return 0; } +#ifdef CONFIG_MPC8548 /* - * Adjust DDR II IO voltage biasing. It just makes it work. + * Adjust DDR II IO voltage biasing - fix only 8548 rev 1. */ - if (spd.mem_type == SPD_MEMTYPE_DDR2) { + if (((get_svr() & 0xffff00f0) == ((SVR_8548_E << 16) | 0x10)) + && spd.mem_type == SPD_MEMTYPE_DDR2) { + volatile ccsr_gur_t *gur = &immap->im_gur; gur->ddrioovcr = (0 | 0x80000000 /* Enable */ | 0x10000000 /* VSEL to 1.8V */ ); } +#endif /* * Determine the size of each Rank in bytes. @@ -786,9 +829,11 @@ spd_sdram(void) * Is this an ECC DDR chip? * But don't mess with it if the DDR controller will init mem. */ -#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) +#if defined(CONFIG_DDR_ECC) if (spd.config == 0x02) { +#if !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) ddr->err_disable = 0x0000000d; +#endif ddr->err_sbe = 0x00ff0000; } debug("DDR: err_disable = 0x%08x\n", ddr->err_disable); @@ -991,17 +1036,24 @@ setup_laws_and_tlbs(unsigned int memsize) break; case 256: case 512: + tlb_size = BOOKE_PAGESZ_256M; + break; case 1024: case 2048: - tlb_size = BOOKE_PAGESZ_256M; + if (PVR_VER(get_pvr()) > PVR_85xx>>16) + tlb_size = BOOKE_PAGESZ_1G; + else + tlb_size = BOOKE_PAGESZ_256M; break; default: puts("DDR: only 16M,32M,64M,128M,256M,512M,1G and 2G are supported.\n"); /* * The memory was not able to be mapped. + * Default to a small size. */ - return 0; + tlb_size = BOOKE_PAGESZ_64M; + memsize = 64; break; } diff --git a/cpu/mpc85xx/speed.c b/cpu/mpc85xx/speed.c index ca81ee7..3c87926 100644 --- a/cpu/mpc85xx/speed.c +++ b/cpu/mpc85xx/speed.c @@ -1,5 +1,5 @@ /* - * Copyright 2004 Freescale Semiconductor. + * Copyright 2004, 2007 Freescale Semiconductor, Inc. * (C) Copyright 2003 Motorola Inc. * Xianghua Xiao, (X.Xiao(a)motorola.com) * @@ -31,27 +31,32 @@ DECLARE_GLOBAL_DATA_PTR; -/* --------------------------------------------------------------- */ -void get_sys_info (sys_info_t * sysInfo) +void get_sys_info (sys_info_t *sysInfo) { - volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile immap_t *immap = (immap_t *)CFG_IMMR; volatile ccsr_gur_t *gur = &immap->im_gur; uint plat_ratio,e500_ratio; plat_ratio = (gur->porpllsr) & 0x0000003e; plat_ratio >>= 1; - switch(plat_ratio) { + + switch (plat_ratio) { case 0x02: case 0x03: case 0x04: case 0x05: case 0x06: + case 0x07: case 0x08: case 0x09: case 0x0a: + case 0x0b: case 0x0c: + case 0x0e: + case 0x0f: case 0x10: + case 0x14: sysInfo->freqSystemBus = plat_ratio * CONFIG_SYS_CLK_FREQ; break; default: @@ -62,6 +67,12 @@ void get_sys_info (sys_info_t * sysInfo) e500_ratio = (gur->porpllsr) & 0x003f0000; e500_ratio >>= 16; switch(e500_ratio) { + case 0x02: + sysInfo->freqProcessor = sysInfo->freqSystemBus; + break; + case 0x03: + sysInfo->freqProcessor = 3*sysInfo->freqSystemBus/2; + break; case 0x04: sysInfo->freqProcessor = 2*sysInfo->freqSystemBus; break; @@ -74,6 +85,12 @@ void get_sys_info (sys_info_t * sysInfo) case 0x07: sysInfo->freqProcessor = 7*sysInfo->freqSystemBus/2; break; + case 0x08: + sysInfo->freqProcessor = 4*sysInfo->freqSystemBus; + break; + case 0x09: + sysInfo->freqProcessor = 9*sysInfo->freqSystemBus/2; + break; default: sysInfo->freqProcessor = 0; break; -- 1.5.0.3

1 0

[U-Boot-Users] [PATCH 2/4] Add MPC8544DS basic port board files.
by Jon Loeliger 11 Apr '07

11 Apr '07

Add board port under new board/freescale directory structure and reuse existing PIXIS FPGA support there. Signed-off-by: Ed Swarthout <Ed.Swarthout(a)freescale.com> Signed-off-by: Jon Loeliger <jdl(a)freescale.com> --- board/freescale/mpc8544ds/Makefile | 58 ++++++++ board/freescale/mpc8544ds/config.mk | 32 +++++ board/freescale/mpc8544ds/init.S | 243 +++++++++++++++++++++++++++++++++ board/freescale/mpc8544ds/mpc8544ds.c | 205 +++++++++++++++++++++++++++ board/freescale/mpc8544ds/u-boot.lds | 148 ++++++++++++++++++++ 5 files changed, 686 insertions(+), 0 deletions(-) create mode 100644 board/freescale/mpc8544ds/Makefile create mode 100644 board/freescale/mpc8544ds/config.mk create mode 100644 board/freescale/mpc8544ds/init.S create mode 100644 board/freescale/mpc8544ds/mpc8544ds.c create mode 100644 board/freescale/mpc8544ds/u-boot.lds diff --git a/board/freescale/mpc8544ds/Makefile b/board/freescale/mpc8544ds/Makefile new file mode 100644 index 0000000..bec2168 --- /dev/null +++ b/board/freescale/mpc8544ds/Makefile @@ -0,0 +1,58 @@ +# +# Copyright 2007 Freescale Semiconductor, Inc. +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +# ifneq ($(OBJTREE),$(SRCTREE)) +# $(shell mkdir -p $(obj)./common) +# endif + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o \ + ../common/pixis.o + +SOBJS := init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) crv $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/mpc8544ds/config.mk b/board/freescale/mpc8544ds/config.mk new file mode 100644 index 0000000..85663ef --- /dev/null +++ b/board/freescale/mpc8544ds/config.mk @@ -0,0 +1,32 @@ +# +# Copyright 2007 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# mpc8544ds board +# +ifndef TEXT_BASE +TEXT_BASE = 0xfff80000 +endif + +PLATFORM_CPPFLAGS += -DCONFIG_E500=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC8544=1 diff --git a/board/freescale/mpc8544ds/init.S b/board/freescale/mpc8544ds/init.S new file mode 100644 index 0000000..296fee5 --- /dev/null +++ b/board/freescale/mpc8544ds/init.S @@ -0,0 +1,243 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <ppc_asm.tmpl> +#include <ppc_defs.h> +#include <asm/cache.h> +#include <asm/mmu.h> +#include <config.h> +#include <mpc85xx.h> + +#define LAWAR_TRGT_PCI1 0x00000000 +#define LAWAR_TRGT_PCIE1 0x00200000 +#define LAWAR_TRGT_PCIE2 0x00100000 +#define LAWAR_TRGT_PCIE3 0x00300000 +#define LAWAR_TRGT_LBC 0x00400000 +#define LAWAR_TRGT_DDR 0x00f00000 + +/* + * TLB0 and TLB1 Entries + * + * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR. + * However, CCSRBAR is then relocated to CFG_CCSRBAR right after + * these TLB entries are established. + * + * The TLB entries for DDR are dynamically setup in spd_sdram() + * and use TLB1 Entries 8 through 15 as needed according to the + * size of DDR memory. + * + * MAS0: tlbsel, esel, nv + * MAS1: valid, iprot, tid, ts, tsize + * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr + */ + +#define entry_start \ + mflr r1 ; \ + bl 0f ; + +#define entry_end \ +0: mflr r0 ; \ + mtlr r1 ; \ + blr ; + + + .section .bootpg, "ax" + .globl tlb1_entry +tlb1_entry: + entry_start + + /* + * Number of TLB0 and TLB1 entries in the following table + */ + .long (2f-1f)/16 +1: + /* + * TLB0 4K Non-cacheable, guarded + * 0xff700000 4K Initial CCSRBAR mapping + * + * This ends up at a TLB0 Index==0 entry, and must not collide + * with other TLB0 Entries. + */ + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB0 16K Cacheable, guarded + * Temporary Global data for initialization + * + * Use four 4K TLB0 entries. These entries must be cacheable + * as they provide the bootstrap memory before the memory + * controler and real memory have been configured. + * + * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, + * and must not collide with other TLB0 entries. + */ + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), + 0,0,0,0,0,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), + 0,0,0,0,0,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), + 0,0,0,0,0,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), + 0,0,0,0,0,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + + /* + * TLB 0: 64M Non-cacheable, guarded + * 0xfc000000 64M Covers FLASH at 0xFE800000 and 0xFF800000 + * Out of reset this entry is only 4K. + */ + .long TLB1_MAS0(1, 0, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_BOOT_BLOCK), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_BOOT_BLOCK), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 1: 1G Non-cacheable, guarded + * 0x80000000 1G PCIE 8,9,a,b + */ + .long TLB1_MAS0(1, 1, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCIE_PHYS), + 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCIE_PHYS), + 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 2: 256M Non-cacheable, guarded + */ + .long TLB1_MAS0(1, 2, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS), + 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 3: 256M Non-cacheable, guarded + */ + .long TLB1_MAS0(1, 3, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS + 0x10000000), + 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS + 0x10000000), + 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 4: 64M Non-cacheable, guarded + * 0xe000_0000 1M CCSRBAR + * 0xe100_0000 255M PCI IO range + */ + .long TLB1_MAS0(1, 4, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + +#ifdef CFG_LBC_CACHE_BASE + /* + * TLB 5: 64M Cacheable, non-guarded + */ + .long TLB1_MAS0(1, 5, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_CACHE_BASE), 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_CACHE_BASE), 0,0,0,0,0,1,0,1,0,1) +#endif + /* + * TLB 6: 64M Non-cacheable, guarded + * 0xf8000000 64M PIXIS 0xF8000000 - 0xFBFFFFFF + */ + .long TLB1_MAS0(1, 6, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_NONCACHE_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_NONCACHE_BASE), 0,0,0,0,0,1,0,1,0,1) +2: + entry_end + +/* + * LAW(Local Access Window) configuration: + * + * + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + * + * LAW 0 is reserved for boot mapping + */ + + .section .bootpg, "ax" + .globl law_entry +law_entry: + entry_start + + .long (4f-3f)/8 +3: + .long 0 + .long (LAWAR_TRGT_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN + + .long (CFG_PCI1_MEM_BASE>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M) + + .long (CFG_PCI1_IO_PHYS>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M) + + .long (CFG_LBC_CACHE_BASE>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M) + + .long (CFG_PCIE1_MEM_PHYS>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCIE1 | (LAWAR_SIZE & LAWAR_SIZE_256M) + + /* To keep to 10 LAWs, PCIE1_IO_PHYS must use top of mem region */ + + .long (CFG_PCIE2_MEM_PHYS>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCIE2 | (LAWAR_SIZE & LAWAR_SIZE_512M) + + .long (CFG_PCIE2_IO_PHYS>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCIE2 | (LAWAR_SIZE & LAWAR_SIZE_16M) + + .long (CFG_PCIE3_MEM_PHYS>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCIE3 | (LAWAR_SIZE & LAWAR_SIZE_256M) + + .long (CFG_PCIE3_IO_PHYS>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCIE3 | (LAWAR_SIZE & LAWAR_SIZE_16M) +4: + entry_end diff --git a/board/freescale/mpc8544ds/mpc8544ds.c b/board/freescale/mpc8544ds/mpc8544ds.c new file mode 100644 index 0000000..9059934 --- /dev/null +++ b/board/freescale/mpc8544ds/mpc8544ds.c @@ -0,0 +1,205 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <command.h> +#include <asm/processor.h> +#include <asm/immap_85xx.h> +#include <spd.h> +#include <miiphy.h> + +#include "../common/pixis.h" + +#if defined(CONFIG_OF_FLAT_TREE) +#include <ft_build.h> +extern void ft_cpu_setup(void *blob, bd_t *bd); +#endif + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) +extern void ddr_enable_ecc(unsigned int dram_size); +#endif + +extern long int spd_sdram(void); + +void sdram_init(void); + +int board_early_init_f (void) +{ + return 0; +} + +int checkboard (void) +{ + volatile immap_t *immap = (immap_t *) CFG_CCSRBAR; + volatile ccsr_gur_t *gur = &immap->im_gur; + + if ((uint)&gur->porpllsr != 0xe00e0000) { + printf("immap size error %x\n",&gur->porpllsr); + } + printf ("Board: MPC8544DS\n"); + + return 0; +} + +long int +initdram(int board_type) +{ + long dram_size = 0; + + puts("Initializing\n"); + + dram_size = spd_sdram(); + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* + * Initialize and enable DDR ECC. + */ + ddr_enable_ecc(dram_size); +#endif + puts(" DDR: "); + return dram_size; +} + + +#if defined(CFG_DRAM_TEST) +int +testdram(void) +{ + uint *pstart = (uint *) CFG_MEMTEST_START; + uint *pend = (uint *) CFG_MEMTEST_END; + uint *p; + + printf("Testing DRAM from 0x%08x to 0x%08x\n", + CFG_MEMTEST_START, + CFG_MEMTEST_END); + + printf("DRAM test phase 1:\n"); + for (p = pstart; p < pend; p++) + *p = 0xaaaaaaaa; + + for (p = pstart; p < pend; p++) { + if (*p != 0xaaaaaaaa) { + printf ("DRAM test fails at: %08x\n", (uint) p); + return 1; + } + } + + printf("DRAM test phase 2:\n"); + for (p = pstart; p < pend; p++) + *p = 0x55555555; + + for (p = pstart; p < pend; p++) { + if (*p != 0x55555555) { + printf ("DRAM test fails at: %08x\n", (uint) p); + return 1; + } + } + + printf("DRAM test passed.\n"); + return 0; +} +#endif + + + +int last_stage_init(void) +{ + return 0; +} + + +unsigned long +get_board_sys_clk(ulong dummy) +{ + u8 i, go_bit, rd_clks; + ulong val = 0; + + go_bit = in8(PIXIS_BASE + PIXIS_VCTL); + go_bit &= 0x01; + + rd_clks = in8(PIXIS_BASE + PIXIS_VCFGEN0); + rd_clks &= 0x1C; + + /* + * Only if both go bit and the SCLK bit in VCFGEN0 are set + * should we be using the AUX register. Remember, we also set the + * GO bit to boot from the alternate bank on the on-board flash + */ + + if (go_bit) { + if (rd_clks == 0x1c) + i = in8(PIXIS_BASE + PIXIS_AUX); + else + i = in8(PIXIS_BASE + PIXIS_SPD); + } else { + i = in8(PIXIS_BASE + PIXIS_SPD); + } + + i &= 0x07; + + switch (i) { + case 0: + val = 33333333; + break; + case 1: + val = 40000000; + break; + case 2: + val = 50000000; + break; + case 3: + val = 66666666; + break; + case 4: + val = 83000000; + break; + case 5: + val = 100000000; + break; + case 6: + val = 133333333; + break; + case 7: + val = 166666666; + break; + } + + return val; +} + +#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) +void +ft_board_setup(void *blob, bd_t *bd) +{ + u32 *p; + int len; + + ft_cpu_setup(blob, bd); + + p = ft_get_prop(blob, "/memory/reg", &len); + if (p != NULL) { + *p++ = cpu_to_be32(bd->bi_memstart); + *p = cpu_to_be32(bd->bi_memsize); + } +} +#endif + diff --git a/board/freescale/mpc8544ds/u-boot.lds b/board/freescale/mpc8544ds/u-boot.lds new file mode 100644 index 0000000..1a8aaa9 --- /dev/null +++ b/board/freescale/mpc8544ds/u-boot.lds @@ -0,0 +1,148 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + .bootpg 0xFFFFF000 : + { + cpu/mpc85xx/start.o (.bootpg) + board/freescale/mpc8544ds/init.o (.bootpg) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/mpc85xx/start.o (.text) + board/freescale/mpc8544ds/init.o (.text) + cpu/mpc85xx/traps.o (.text) + cpu/mpc85xx/interrupts.o (.text) + cpu/mpc85xx/cpu_init.o (.text) + cpu/mpc85xx/cpu.o (.text) + cpu/mpc85xx/speed.o (.text) + common/dlmalloc.o (.text) + lib_generic/crc32.o (.text) + lib_ppc/extable.o (.text) + lib_generic/zlib.o (.text) + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} -- 1.5.0.3

1 0

[U-Boot-Users] [PATCH 1/4] Add MPC8544DS main configuration file.
by Jon Loeliger 11 Apr '07

11 Apr '07

Signed-off-by: Ed Swarthout <Ed.Swarthout(a)freescale.com> Signed-off-by: Jon Loeliger <jdl(a)freescale.com> --- include/configs/MPC8544DS.h | 591 +++++++++++++++++++++++++++++++++++++++++++ 1 files changed, 591 insertions(+), 0 deletions(-) create mode 100644 include/configs/MPC8544DS.h diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h new file mode 100644 index 0000000..4c34308 --- /dev/null +++ b/include/configs/MPC8544DS.h @@ -0,0 +1,591 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * mpc8544ds board configuration file + * + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ +#define CONFIG_MPC8544 1 +#define CONFIG_MPC8544DS 1 + +#undef CONFIG_PCI /* Enable PCI/PCIE */ +#undef CONFIG_PCI1 /* PCI controller 1 */ +#undef CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ +#undef CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */ +#undef CONFIG_PCIE3 /* PCIE controler 3 (ULI bridge) */ +#undef CONFIG_FSL_PCI_INIT /* Use common FSL init code */ + +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#undef CONFIG_DDR_DLL +#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + +#define CONFIG_DDR_ECC_CMD + +/* + * When initializing flash, if we cannot find the manufacturer ID, + * assume this is the AMD flash associated with the CDS board. + * This allows booting from a promjet. + */ +#define CONFIG_ASSUME_AMD_FLASH + +#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */ + +#ifndef __ASSEMBLY__ +extern unsigned long get_board_sys_clk(unsigned long dummy); +#endif +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ +#define CONFIG_CLEAR_LAW0 /* Clear LAW0 in cpu_init_r */ + +/* + * Only possible on E500 Version 2 or newer cores. + */ +#define CONFIG_ENABLE_36BIT_PHYS 1 + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ + +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00200000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00400000 +#define CFG_ALT_MEMTEST +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ +#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ + +#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000) +#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000) +#define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000) +#define CFG_PCIE3_ADDR (CFG_CCSRBAR+0xb000) + +/* + * DDR Setup + */ +#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE + +#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ + +/* + * Make sure required options are set + */ +#ifndef CONFIG_SPD_EEPROM +#error ("CONFIG_SPD_EEPROM is required") +#endif + +#undef CONFIG_CLOCKS_IN_MHZ + +/* + * Memory map + * + * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable + * + * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable + * + * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable + * + * 0xe000_0000 0xe00f_ffff CCSR 1M non-cacheable + * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable + * + * Localbus cacheable + * + * 0xf000_0000 0xf3ff_ffff SDRAM 64M Cacheable + * 0xf401_0000 0xf401_3fff L1 for stack 4K Cacheable TLB0 + * + * Localbus non-cacheable + * + * 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M non-cacheable + * 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M non-cacheable + * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M non-cacheable + * + */ + +/* + * Local Bus Definitions + */ +#define CFG_BOOT_BLOCK 0xfc000000 /* boot TLB */ + +#define CFG_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */ + +#define CFG_FLASH_BASE 0xff800000 /* start of FLASH 8M */ + +#define CFG_BR0_PRELIM 0xff801001 +#define CFG_BR1_PRELIM 0xfe801001 + +#define CFG_OR0_PRELIM 0xff806e65 +#define CFG_OR1_PRELIM 0xff806e65 + +#define CFG_FLASH_BANKS_LIST {0xfe800000,CFG_FLASH_BASE} + +#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ +#define CFG_MAX_FLASH_SECT 128 /* sectors per device */ +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CFG_FLASH_CFI_DRIVER +#define CFG_FLASH_CFI +#define CFG_FLASH_EMPTY_INFO + +#define CFG_LBC_NONCACHE_BASE 0xf8000000 + +#define CFG_BR2_PRELIM 0xf8201001 /* port size 16bit */ +#define CFG_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/ + +#define CFG_BR3_PRELIM 0xf8100801 /* port size 8bit */ +#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ + +#define PIXIS_BASE 0xf8100000 /* PIXIS registers */ +#define PIXIS_ID 0x0 /* Board ID at offset 0 */ +#define PIXIS_VER 0x1 /* Board version at offset 1 */ +#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ +#define PIXIS_RST 0x4 /* PIXIS Reset Control register */ +#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch + * register */ +#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ +#define PIXIS_VCTL 0x10 /* VELA Control Register */ +#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ +#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ +#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ +#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ +#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ +#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ +#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ + + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM 1 +#define CFG_INIT_L1_LOCK 1 +#define CFG_INIT_L1_ADDR 0xf4010000 /* Initial L1 address */ +#define CFG_INIT_L1_END 0x00004000 /* End of used area in RAM */ + +/* define to use L2SRAM as initial stack */ +#undef CONFIG_L2_INIT_RAM +#define CFG_INIT_L2_ADDR 0xf8fc0000 +#define CFG_INIT_L2_END 0x00040000 /* End of used area in RAM */ + +#ifdef CONFIG_L1_INIT_RAM +#define CFG_INIT_RAM_ADDR CFG_INIT_L1_ADDR +#define CFG_INIT_RAM_END CFG_INIT_L1_END +#else +#define CFG_INIT_RAM_ADDR CFG_INIT_L2_ADDR +#define CFG_INIT_RAM_END CFG_INIT_L2_END +#endif + +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) +#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) + +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_BOARD_SETUP 1 + +/* maximum size of the flat tree (8K) */ +#define OF_FLAT_TREE_MAX_SIZE 8192 + +#define OF_CPU "PowerPC,8544@0" +#define OF_SOC "soc8544@e0000000" +#define OF_TBCLK (bd->bi_busfreq / 8) +#define OF_STDOUT_PATH "/soc8544@e0000000/serial@4500" + +/* I2C */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_EEPROM_ADDR 0x57 +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CFG_I2C_OFFSET 0x3100 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ +#define CFG_PCIE_PHYS 0x80000000 /* 1G PCIE TLB */ +#define CFG_PCI_PHYS 0xc0000000 /* 512M PCI TLB */ + +#define CFG_PCI1_MEM_BASE 0xc0000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI1_IO_BASE 0x00000000 +#define CFG_PCI1_IO_PHYS 0xe1000000 +#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */ + +/* PCI view of System Memory */ +#define CFG_PCI_MEMORY_BUS 0x00000000 +#define CFG_PCI_MEMORY_PHYS 0x00000000 +#define CFG_PCI_MEMORY_SIZE 0x80000000 + +/* controller 2, Slot 1, tgtid 1, Base address 9000 */ +#define CFG_PCIE2_MEM_BASE 0x80000000 +#define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE +#define CFG_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCIE2_IO_BASE 0x00000000 +#define CFG_PCIE2_IO_PHYS 0xe2000000 +#define CFG_PCIE2_IO_SIZE 0x00100000 /* 1M */ + +/* controller 1, Slot 2,tgtid 2, Base address a000 */ +#define CFG_PCIE1_MEM_BASE 0xa0000000 +#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE +#define CFG_PCIE1_MEM_SIZE 0x08000000 /* 128M */ +#define CFG_PCIE1_MEM_BASE2 0xa8000000 +#define CFG_PCIE1_MEM_PHYS2 CFG_PCIE1_MEM_BASE2 +#define CFG_PCIE1_MEM_SIZE2 0x04000000 /* 64M */ +#define CFG_PCIE1_IO_BASE 0x00000000 /* reuse mem LAW */ +#define CFG_PCIE1_IO_PHYS 0xaf000000 +#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */ + +/* controller 3, direct to uli, tgtid 3, Base address b000 */ +#define CFG_PCIE3_MEM_BASE 0xb0000000 +#define CFG_PCIE3_MEM_PHYS CFG_PCIE3_MEM_BASE +#define CFG_PCIE3_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCIE3_IO_BASE 0x00000000 +#define CFG_PCIE3_IO_PHYS 0xe3000000 +#define CFG_PCIE3_IO_SIZE 0x00100000 /* 1M */ + +#if defined(CONFIG_PCI) + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP +#define CONFIG_RTL8139 + +#ifdef CONFIG_RTL8139 +/* This macro is used by RTL8139 but not defined in PPC architecture */ +#define KSEG1ADDR(x) (x) +#define _IO_BASE 0x00000000 +#endif + +#ifndef CONFIG_PCI_PNP + #define PCI_ENET0_IOADDR CFG_PCI1_IO_BASE + #define PCI_ENET0_MEMADDR CFG_PCI1_IO_BASE + #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */ +#endif + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#define CONFIG_SCSI_AHCI + +#ifdef CONFIG_SCSI_AHCI +#define CONFIG_SATA_ULI5288 +#define CFG_SCSI_MAX_SCSI_ID 4 +#define CFG_SCSI_MAX_LUN 1 +#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN) +#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE +#endif /* SCSCI */ + +#endif /* CONFIG_PCI */ + + +#if defined(CONFIG_TSEC_ENET) + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ +#define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "eTSEC1" +#define CONFIG_MPC85XX_TSEC3 1 +#define CONFIG_MPC85XX_TSEC3_NAME "eTSEC3" +#undef CONFIG_MPC85XX_FEC + +#define TSEC1_PHY_ADDR 0 +#define TSEC3_PHY_ADDR 1 + +#define TSEC1_PHYIDX 0 +#define TSEC3_PHYIDX 0 + +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ + +#endif /* CONFIG_TSEC_ENET */ + +/* + * Environment + */ +#define CFG_ENV_IS_IN_FLASH 1 +#if CFG_MONITOR_BASE > 0xfff80000 +#define CFG_ENV_ADDR 0xfff80000 +#else +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +#endif +#define CFG_ENV_SIZE 0x2000 +#define CFG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#if defined(CONFIG_PCI) +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_PCI \ + | CFG_CMD_PING \ + | CFG_CMD_I2C \ + | CFG_CMD_MII \ + | CFG_CMD_BEDBUG \ + | CFG_CMD_NET) +#else +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_PING \ + | CFG_CMD_I2C \ + | CFG_CMD_MII) +#endif +#include <cmd_confdefs.h> + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ + +/* Cache Configuration */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +/* The mac addresses for all ethernet interface */ +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_ETHADDR 00:E0:0C:02:00:FD +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 00:E0:0C:02:01:FD +#define CONFIG_HAS_ETH2 +#define CONFIG_ETH2ADDR 00:E0:0C:02:02:FD +#define CONFIG_HAS_ETH3 +#define CONFIG_ETH3ADDR 00:E0:0C:02:03:FD +#endif + +#define CONFIG_IPADDR 192.168.1.251 + +#define CONFIG_HOSTNAME 8544ds_unknown +#define CONFIG_ROOTPATH /nfs/mpc85xx +#define CONFIG_BOOTFILE 8544ds_tmt/uImage.uboot + +#define CONFIG_SERVERIP 192.168.0.1 +#define CONFIG_GATEWAYIP 192.168.0.1 +#define CONFIG_NETMASK 255.255.0.0 + +#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/ + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ + +#define CONFIG_BAUDRATE 115200 + +#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3) +#define PCIE_ENV \ + "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \ + "echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \ + "pcie1regs=setenv a e000a; run pciereg\0" \ + "pcie2regs=setenv a e0009; run pciereg\0" \ + "pcie3regs=setenv a e000b; run pciereg\0" \ + "pcieerr=md ${a}020 1; md ${a}e00;" \ + "pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \ + "pci d.w $b.0 56 1;" \ + "pci d $b.0 104 1;pci d $b.0 110 1;pci d $b.0 130 1\0" \ + "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff;" \ + "pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff;" \ + "pci w $b.0 104 ffffffff; pci w $b.0 110 ffffffff;" \ + "pci w $b.0 130 ffffffff\0" \ + "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \ + "pcie1err=setenv a e000a; run pcieerr\0" \ + "pcie2err=setenv a e0009; run pcieerr\0" \ + "pcie3err=setenv a e000b; run pcieerr\0" \ + "pcie1errc=setenv a e000a; run pcieerrc\0" \ + "pcie2errc=setenv a e0009; run pcieerrc\0" \ + "pcie3errc=setenv a e000b; run pcieerrc\0" +#else +#define PCIE_ENV "" +#endif + +#if defined(CONFIG_PCI1) +#define PCI_ENV \ + "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \ + "echo e;md ${a}e00 9\0" \ + "pci1regs=setenv a e0008; run pcireg\0" \ + "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \ + "pci d.w $b.0 56 1\0" \ + "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \ + "pci w.w $b.0 56 ffff\0" \ + "pci1err=setenv a e0008; run pcierr\0" \ + "pci1errc=setenv a e0008; run pcierrc\0" +#else +#define PCI_ENV "" +#endif + +#if defined(CONFIG_TSEC_ENET) +#define ENET_ENV \ + "enetreg1=md ${a}000 2; md ${a}010 9; md ${a}050 4; md ${a}08c 1;" \ + "md ${a}098 2\0" \ + "enetregt=echo t;md ${a}100 6; md ${a}140 2; md ${a}180 10; md ${a}200 10\0" \ + "enetregr=echo r;md ${a}300 6; md ${a}330 5; md ${a}380 10; md ${a}400 10\0" \ + "enetregm=echo mac;md ${a}500 5; md ${a}520 28;echo fifo;md ${a}a00 1;" \ + "echo mib;md ${a}680 31\0" \ + "enetreg=run enetreg1; run enetregm; run enetregt; run enetregr\0" \ + "enet1regs=setenv a e0024; run enetreg\0" \ + "enet3regs=setenv a e0026; run enetreg\0" +#else +#define ENET_ENV "" +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=8544ds_tmt/ramdisk.uboot\0" \ + "fdtaddr=400000\0" \ + "fdtfile=8544ds_tmt/mpc8544ds.dtb\0" \ + "eoi=mw e00400b0 0\0" \ + "iack=md e00400a0 1\0" \ + "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4; md ${a}bf0 4;" \ + "md ${a}e00 3; md ${a}e20 3; md ${a}e40 7; md ${a}f00 5\0" \ + "ddrregs=setenv a e0002; run ddrreg\0" \ + "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}b20 3;" \ + "md ${a}e00 1; md ${a}e60 1; md ${a}ef0 15\0" \ + "guregs=setenv a e00e0; run gureg\0" \ + "ecmreg=md ${a}000 1; md ${a}010 1; md ${a}bf8 2; md ${a}e00 6\0" \ + "ecmregs=setenv a e0001; run ecmreg\0" \ + PCIE_ENV \ + PCI_ENV \ + ENET_ENV + + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND \ + "setenv bootargs root=/dev/sda3 rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#endif /* __CONFIG_H */ -- 1.5.0.3

1 0

[U-Boot-Users] [PATCH 0/4] Add Initial MPC8544 Basic Board Port
by Jon Loeliger 11 Apr '07

11 Apr '07

Andy, The following patch set adds the initial MPC8544DS board port. This is the first Freescale board to be added under the new board/freescale directory, and as such will rely on the previously published patch for the 8641 that adds the PIXIS support. Please apply this to your mpc85xx custodian tree. Thanks, jdl

1 0

[U-Boot-Users] [PATCH] Fix i2c divisor calcularion for PPC4xx
by Jeff Mann 11 Apr '07

11 Apr '07

U-Boot Users: This patch fixes changes the i2c_init(...) function to use the function get_OPB_freq() rather than calculating the OPB speed by sysInfo.freqPLB/sysInfo.pllOpbDiv. The get_OPB_freq() function is specific per processor. The prior method was not and so was calculating the wrong speed for some PPC4xx processors. PATCH: * Fixes OPB Speed calculation used for initializing i2c in PPC4xx processors. Signed-off-by: Jeffrey Mann <mannj(a)embeddedplanet.com> --- old/cpu/ppc4xx/i2c.c 2007-04-06 11:46:35.000000000 -0400 +++ new/cpu/ppc4xx/i2c.c 2007-04-11 11:51:35.000000000 -0400 @@ -124,8 +124,7 @@ void i2c_init(int speed, int slaveadd) /* Clock divide Register */ /* get OPB frequency */ - get_sys_info(&sysInfo); - freqOPB = sysInfo.freqPLB / sysInfo.pllOpbDiv; + freqOPB = get_OPB_freq(); /* set divisor according to freqOPB */ divisor = (freqOPB - 1) / 10000000; if (divisor == 0)

1 0

[U-Boot-Users] Kernel Panic
by harsh poshtiwala 11 Apr '07

11 Apr '07

Hi , I have been trying to create MTD partitions and JFFS2 file system on ST linux kerenel version 2.6.12 The processor is Nomadik. The development board is NMTV10. I enabled MTD paprameters and JFFS2 parameters while configuring the kernel. Attached is the .config file and the log of u-boot prompt. I erased the nand with command nand erase 0x400000 0x800000 Now i loaded the jffs2 image loadb 0x100000 Now i write this to Nand nand write.jffs2 0x100000 0x400000 0x002c0000 where 0x002c0000 is the size of kerenl image. I get the message kerenl panic. with the statement no Init found. Did i miss anything while configuring the kerenel. i set boot command option as follow mem=64M root=dev/ram0 console=ttyAMA1,112500n8 Did i miss anything ? I would appreciate your response. -- Thanks & Regards Harsh

2 1

[U-Boot-Users] want join maillist
by 朱洪亮 11 Apr '07

11 Apr '07

this is my email

1 0

[U-Boot-Users] "7.at91rm9200dk":(1 of 1) [PATCH][ARM] Add PIO control for at91rm9200dk LEDs and Mux.
by Ulf Samuelsson 11 Apr '07

11 Apr '07

Author: Ulf Samuelsson <ulf(a)atmel.com> Date: 2007-03-27 Subject: "7.at91rm9200dk":(1 of 1) [PATCH][ARM] Add PIO control for at91rm9200dk LEDs and Mux. CHANGELOG: [PATCH][ARM] Add PIO control for at91rm9200dk LEDs and Mux. Introduce a new command CFG_CMD_MUX 0x8000000000000000ULL Patch generated from files: board_at91rm9200dk_led.c.patch board_at91rm9200dk_Makefile.patch board_at91rm9200dk_mux.c.patch common_soft_i2c.c.patch include_cmd_confdefs.h.patch include_configs_at91rm9200dk.h.patch include_led.h.patch Signed-off-by: Ulf Samuelsson --------------------------------------------------------------------------------------------------------------------------------- diff -urN u-boot-1.2.0/board/at91rm9200dk/led.c u-boot-1.2.0-atmel/board/at91rm9200dk/led.c --- u-boot-1.2.0/board/at91rm9200dk/led.c 1970-01-01 01:00:00.000000000 +0100 +++ u-boot-1.2.0-atmel/board/at91rm9200dk/led.c 2007-03-27 10:40:35.000000000 +0200 @@ -0,0 +1,81 @@ +/* + * (C) Copyright 2006 + * Atmel Nordic AB <www.atmel.com> + * Ulf Samuelsson <ulf(a)atmel.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/arch/AT91RM9200.h> + +#define GREEN_LED AT91C_PIO_PB0 +#define YELLOW_LED AT91C_PIO_PB1 +#define RED_LED AT91C_PIO_PB2 + +void green_LED_on(void) +{ + AT91PS_PIO PIOB = AT91C_BASE_PIOB; + PIOB->PIO_CODR = GREEN_LED; +} + +void yellow_LED_on(void) +{ + AT91PS_PIO PIOB = AT91C_BASE_PIOB; + PIOB->PIO_CODR = YELLOW_LED; +} + +void red_LED_on(void) +{ + AT91PS_PIO PIOB = AT91C_BASE_PIOB; + PIOB->PIO_CODR = RED_LED; +} + +void green_LED_off(void) +{ + AT91PS_PIO PIOB = AT91C_BASE_PIOB; + PIOB->PIO_SODR = GREEN_LED; +} + +void yellow_LED_off(void) +{ + AT91PS_PIO PIOB = AT91C_BASE_PIOB; + PIOB->PIO_SODR = YELLOW_LED; +} + +void red_LED_off(void) +{ + AT91PS_PIO PIOB = AT91C_BASE_PIOB; + PIOB->PIO_SODR = RED_LED; +} + + +void LED_init (void) +{ + DECLARE_GLOBAL_DATA_PTR; + AT91PS_PIO PIOB = AT91C_BASE_PIOB; + AT91PS_PMC PMC = AT91C_BASE_PMC; + PMC->PMC_PCER = (1 << AT91C_ID_PIOB); /* Enable PIOB clock */ + /* Disable peripherals on LEDs */ + PIOB->PIO_PER = AT91C_PIO_PB2 | AT91C_PIO_PB1 | AT91C_PIO_PB0; + /* Enable pins as outputs */ + PIOB->PIO_OER = AT91C_PIO_PB2 | AT91C_PIO_PB1 | AT91C_PIO_PB0; + /* Turn all LEDs OFF */ + PIOB->PIO_SODR = AT91C_PIO_PB2 | AT91C_PIO_PB1 | AT91C_PIO_PB0; +} diff -urN u-boot-1.2.0/board/at91rm9200dk/Makefile u-boot-1.2.0-atmel/board/at91rm9200dk/Makefile --- u-boot-1.2.0/board/at91rm9200dk/Makefile 2007-03-27 09:30:38.000000000 +0200 +++ u-boot-1.2.0-atmel/board/at91rm9200dk/Makefile 2007-03-24 20:07:33.000000000 +0100 @@ -25,7 +25,7 @@ LIB = $(obj)lib$(BOARD).a -COBJS := at91rm9200dk.o flash.o +COBJS := at91rm9200dk.o flash.o led.o mux.o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) diff -urN u-boot-1.2.0/board/at91rm9200dk/mux.c u-boot-1.2.0-atmel/board/at91rm9200dk/mux.c --- u-boot-1.2.0/board/at91rm9200dk/mux.c 1970-01-01 01:00:00.000000000 +0100 +++ u-boot-1.2.0-atmel/board/at91rm9200dk/mux.c 2007-03-24 20:07:33.000000000 +0100 @@ -0,0 +1,36 @@ +#include <config.h> +#include <common.h> +#include <asm/hardware.h> +#include <dataflash.h> + +int AT91F_GetMuxStatus(void) { +#ifdef DATAFLASH_MMC_SELECT + AT91C_BASE_PIOB->PIO_PER = DATAFLASH_MMC_SELECT; /* Set in PIO mode */ + AT91C_BASE_PIOB->PIO_OER = DATAFLASH_MMC_SELECT; /* Configure in output */ + + + if(AT91C_BASE_PIOB->PIO_ODSR & DATAFLASH_MMC_SELECT) { + return 1; + } else { + return 0; + } +#endif +} + +void AT91F_SelectMMC(void) { +#ifdef DATAFLASH_MMC_SELECT + AT91C_BASE_PIOB->PIO_PER = DATAFLASH_MMC_SELECT; /* Set in PIO mode */ + AT91C_BASE_PIOB->PIO_OER = DATAFLASH_MMC_SELECT; /* Configure in output */ + /* Set Output */ + AT91C_BASE_PIOB->PIO_SODR = DATAFLASH_MMC_SELECT; +#endif +} + +void AT91F_SelectSPI(void) { +#ifdef DATAFLASH_MMC_SELECT + AT91C_BASE_PIOB->PIO_PER = DATAFLASH_MMC_SELECT; /* Set in PIO mode */ + AT91C_BASE_PIOB->PIO_OER = DATAFLASH_MMC_SELECT; /* Configure in output */ + /* Clear Output */ + AT91C_BASE_PIOB->PIO_CODR = DATAFLASH_MMC_SELECT; +#endif +} diff -urN u-boot-1.2.0/common/soft_i2c.c u-boot-1.2.0-atmel/common/soft_i2c.c --- u-boot-1.2.0/common/soft_i2c.c 2007-01-07 00:13:11.000000000 +0100 +++ u-boot-1.2.0-atmel/common/soft_i2c.c 2007-03-24 20:07:33.000000000 +0100 @@ -29,7 +29,7 @@ #ifdef CONFIG_MPC8260 /* only valid for MPC8260 */ #include <ioports.h> #endif -#ifdef CONFIG_AT91RM9200DK /* need this for the at91rm9200dk */ +#ifdef CONFIG_AT91RM9200 /* need this for the at91rm9200 */ #include <asm/io.h> #include <asm/arch/hardware.h> #endif diff -urN u-boot-1.2.0/include/cmd_confdefs.h u-boot-1.2.0-atmel/include/cmd_confdefs.h --- u-boot-1.2.0/include/cmd_confdefs.h 2007-01-07 00:13:11.000000000 +0100 +++ u-boot-1.2.0-atmel/include/cmd_confdefs.h 2007-03-24 20:07:33.000000000 +0100 @@ -94,6 +94,7 @@ #define CFG_CMD_EXT2 0x1000000000000000ULL /* EXT2 Support */ #define CFG_CMD_SNTP 0x2000000000000000ULL /* SNTP support */ #define CFG_CMD_DISPLAY 0x4000000000000000ULL /* Display support */ +#define CFG_CMD_MUX 0x8000000000000000ULL /* AT91 MMC/SPI Mux Support */ #define CFG_CMD_ALL 0xFFFFFFFFFFFFFFFFULL /* ALL commands */ @@ -141,7 +142,8 @@ CFG_CMD_SPI | \ CFG_CMD_UNIVERSE | \ CFG_CMD_USB | \ - CFG_CMD_VFD ) + CFG_CMD_VFD | \ + CFG_CMD_MUX) /* Default configuration */ diff -urN u-boot-1.2.0/include/configs/at91rm9200dk.h u-boot-1.2.0-atmel/include/configs/at91rm9200dk.h --- u-boot-1.2.0/include/configs/at91rm9200dk.h 2007-01-07 00:13:11.000000000 +0100 +++ u-boot-1.2.0-atmel/include/configs/at91rm9200dk.h 2007-03-26 22:40:12.000000000 +0200 @@ -150,6 +162,11 @@ #define CONFIG_NET_RETRY_COUNT 20 #define CONFIG_AT91C_USE_RMII +/* AC Characteristics */ +/* DLYBS = tCSS = 250ns min and DLYBCT = tCSH = 250ns */ +#define DATAFLASH_TCSS (0xC << 16) +#define DATAFLASH_TCHS (0x1 << 24) + #define CONFIG_HAS_DATAFLASH 1 #define CFG_SPI_WRITE_TOUT (5*CFG_HZ) #define CFG_MAX_DATAFLASH_BANKS 2 diff -urN u-boot-1.2.0/include/led.h u-boot-1.2.0-atmel/include/led.h --- u-boot-1.2.0/include/led.h 1970-01-01 01:00:00.000000000 +0100 +++ u-boot-1.2.0-atmel/include/led.h 2007-03-24 20:07:32.000000000 +0100 @@ -0,0 +1,45 @@ +/* + * (C) Copyright 2006 + * Atmel Nordic AB <www.atmel.com> + * Ulf Samuelsson <ulf(a)atmel.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + + #ifndef __LED_H +#define __LED_H + +#ifndef __ASSEMBLY__ +extern void LED_init (void); +extern void red_LED_on(void); +extern void red_LED_off(void); +extern void green_LED_on(void); +extern void green_LED_off(void); +extern void yellow_LED_on(void); +extern void yellow_LED_off(void); +#else + .extern LED_init + .extern red_LED_on + .extern red_LED_off + .extern yellow_LED_on + .extern yellow_LED_off + .extern green_LED_on + .extern green_LED_off +#endif +#endif -- Best Regards, Ulf Samuelsson

2 2

[U-Boot-Users] [PATCH] Fix: Bug in MIPS linker scripts
by Robert Deliën 11 Apr '07

11 Apr '07

Hi, This patch fixes the possible alignment error between _gp and __got_start in the linker scripts of all MIPS targets. This problem has been previously reported under the title '_gp and __got_start alignment problem in u-boot.lds. Thanks for your comment Andrew! With kind regards, Robert.

2 1

[U-Boot-Users] (AD)真人个性陶偶礼品
by 90522jkl＠flashget.com 11 Apr '07

11 Apr '07

您好：如果此封邮件打扰到您，我们深表歉意！陶偶网（www.taoou.com)目前推出“真人卡通雕像”，只需要提供您的本人照片，告诉您的想法，即可为您打造出一款真正“独一无二”的个性礼物。目前网上直销价仅为同类产品门店价格的1/2，全球预订，快递到家；纯手工，全身打造，头部表情，衣服，动作，姿势均可参照您提供的照片进行制作！网络沟通方式： MSN: taoou.com(a)hotmail.com QQ: 719784456 直线电话：0755-21280325 热线：13714111542 目前本站每天有数以千计的人浏览，日均流量上万多人次，全球排名突破十五万位，网站信誉良好！更多样式及相关订制流程请上我们的网站：www.taoou.com 　　　　　　　　致礼！

1 0