Hi, I want to apply some simple tests on MPC855T and need to turn on both instruction- and data-cache. I have used the codes in cpu/mpc8xx/start.S(as follows), but it crashes while trying to write IDC_ENABLE to DC_CST. Do I have to enable the MMU first? If so, how? I have tried the code in linuxppc_2_4_devel/arch/ppc/kernel/head_8xx.S, it also crashes while trying to write MSR_DR|MSR_IR to msr.

Any ideas? Thanks!

Qichen

/* ************** dcache_enable in start.S ************ */ .globl dcache_enable dcache_enable: #if 0 SYNC #endif #if 1 lis r3, 0x0400 /* Set cache mode with MMU off */ mtspr MD_CTR, r3 #endif

lis r3, IDC_INVALL@h mtspr DC_CST, r3 #if 0 lis r3, DC_SFWT@h mtspr DC_CST, r3 #endif lis r3, IDC_ENABLE@h mtspr DC_CST, r3 blr

/* ************ turn_on_mmu in head_8xx.S *********** */ bl initial_mmu

/* We now have the lower 8 Meg mapped into TLB entries, and the caches * ready to work. */

turn_on_mmu: mfmsr r0 ori r0,r0,MSR_DR|MSR_IR mtspr SRR1,r0 blr

initial_mmu: tlbia /* Invalidate all TLB entries */ #ifdef CONFIG_PIN_TLB lis r8, MI_RSV4I@h ori r8, r8, 0x1c00 #else li r8, 0 #endif mtspr MI_CTR, r8 /* Set instruction MMU control */

#ifdef CONFIG_PIN_TLB lis r10, (MD_RSV4I | MD_RESETVAL)@h ori r10, r10, 0x1c00 mr r8, r10 #else lis r10, MD_RESETVAL@h #endif #ifndef CONFIG_8xx_COPYBACK oris r10, r10, MD_WTDEF@h #endif mtspr MD_CTR, r10 /* Set data TLB control */

/* Now map the lower 8 Meg into the TLBs. For this quick hack, * we can load the instruction and data TLB registers with the * same values. */ lis r8, KERNELBASE@h /* Create vaddr for TLB */ ori r8, r8, MI_EVALID /* Mark it valid */ mtspr MI_EPN, r8 mtspr MD_EPN, r8 li r8, MI_PS8MEG /* Set 8M byte page */ ori r8, r8, MI_SVALID /* Make it valid */ mtspr MI_TWC, r8 mtspr MD_TWC, r8 li r8, MI_BOOTINIT /* Create RPN for address 0 */ mtspr MI_RPN, r8 /* Store TLB entry */ mtspr MD_RPN, r8 lis r8, MI_Kp@h /* Set the protection mode */ mtspr MI_AP, r8 mtspr MD_AP, r8

/* Map another 8 MByte at the IMMR to get the processor * internal registers (among other things). */ #ifdef CONFIG_PIN_TLB addi r10, r10, 0x0100 mtspr MD_CTR, r10 #endif mfspr r9, 638 /* Get current IMMR */ andis. r9, r9, 0xff80 /* Get 8Mbyte boundary */

mr r8, r9 /* Create vaddr for TLB */ ori r8, r8, MD_EVALID /* Mark it valid */ mtspr MD_EPN, r8 li r8, MD_PS8MEG /* Set 8M byte page */ ori r8, r8, MD_SVALID /* Make it valid */ mtspr MD_TWC, r8 mr r8, r9 /* Create paddr for TLB */ ori r8, r8, MI_BOOTINIT|0x2 /* Inhibit cache -- Cort */ mtspr MD_RPN, r8

#ifdef CONFIG_PIN_TLB /* Map two more 8M kernel data pages. */ addi r10, r10, 0x0100 mtspr MD_CTR, r10

lis r8, KERNELBASE@h /* Create vaddr for TLB */ addis r8, r8, 0x0080 /* Add 8M */ ori r8, r8, MI_EVALID /* Mark it valid */ mtspr MD_EPN, r8 li r9, MI_PS8MEG /* Set 8M byte page */ ori r9, r9, MI_SVALID /* Make it valid */ mtspr MD_TWC, r9 li r11, MI_BOOTINIT /* Create RPN for address 0 */ addis r11, r11, 0x0080 /* Add 8M */ mtspr MD_RPN, r8

addis r8, r8, 0x0080 /* Add 8M */ mtspr MD_EPN, r8 mtspr MD_TWC, r9 addis r11, r11, 0x0080 /* Add 8M */ mtspr MD_RPN, r8 #endif

/* Since the cache is enabled according to the information we * just loaded into the TLB, invalidate and enable the caches here. * We should probably check/set other modes....later. */ lis r8, IDC_INVALL@h mtspr IC_CST, r8 mtspr DC_CST, r8 lis r8, IDC_ENABLE@h mtspr IC_CST, r8 #ifdef CONFIG_8xx_COPYBACK mtspr DC_CST, r8 #else /* For a debug option, I left this here to easily enable * the write through cache mode */ lis r8, DC_SFWT@h mtspr DC_CST, r8 lis r8, IDC_ENABLE@h mtspr DC_CST, r8 #endif blr