Remove leftover DTSI files after OF_UPSTREAM conversion.
Those are no longer used and no longer necessary, remove them.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas(a)mailbox.org>
---
Cc: Adam Ford <aford173(a)gmail.com>
Cc: Tom Rini <trini(a)konsulko.com>
---
arch/arm/dts/salvator-common.dtsi | 1104 ----------------------
arch/arm/dts/salvator-x.dtsi | 29 -
arch/arm/dts/salvator-xs.dtsi | 85 --
arch/arm/dts/ulcb-audio-graph-card.dtsi | 85 --
arch/arm/dts/ulcb-audio-graph-card2.dtsi | 26 -
arch/arm/dts/ulcb.dtsi | 509 ----------
6 files changed, 1838 deletions(-)
delete mode 100644 arch/arm/dts/salvator-common.dtsi
delete mode 100644 arch/arm/dts/salvator-x.dtsi
delete mode 100644 arch/arm/dts/salvator-xs.dtsi
delete mode 100644 arch/arm/dts/ulcb-audio-graph-card.dtsi
delete mode 100644 arch/arm/dts/ulcb-audio-graph-card2.dtsi
delete mode 100644 arch/arm/dts/ulcb.dtsi
diff --git a/arch/arm/dts/salvator-common.dtsi b/arch/arm/dts/salvator-common.dtsi
deleted file mode 100644
index 4a3d5037821..00000000000
--- a/arch/arm/dts/salvator-common.dtsi
+++ /dev/null
@@ -1,1104 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree Source for common parts of Salvator-X board variants
- *
- * Copyright (C) 2015-2016 Renesas Electronics Corp.
- */
-
-/*
- * SSI-AK4613
- *
- * This command is required when Playback/Capture
- *
- * amixer set "DVC Out" 100%
- * amixer set "DVC In" 100%
- *
- * You can use Mute
- *
- * amixer set "DVC Out Mute" on
- * amixer set "DVC In Mute" on
- *
- * You can use Volume Ramp
- *
- * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
- * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
- * amixer set "DVC Out Ramp" on
- * aplay xxx.wav &
- * amixer set "DVC Out" 80% // Volume Down
- * amixer set "DVC Out" 100% // Volume Up
- */
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
- aliases {
- i2c0 = &i2c0;
- i2c1 = &i2c1;
- i2c2 = &i2c2;
- i2c3 = &i2c3;
- i2c4 = &i2c4;
- i2c5 = &i2c5;
- i2c6 = &i2c6;
- i2c7 = &i2c_dvfs;
- serial0 = &scif2;
- serial1 = &hscif1;
- ethernet0 = &avb;
- mmc0 = &sdhi2;
- mmc1 = &sdhi0;
- mmc2 = &sdhi3;
- };
-
- chosen {
- bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
- stdout-path = "serial0:115200n8";
- };
-
- audio_clkout: audio-clkout {
- /*
- * This is same as <&rcar_sound 0>
- * but needed to avoid cs2000/rcar_sound probe dead-lock
- */
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <12288000>;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm1 0 50000>;
-
- brightness-levels = <256 128 64 16 8 4 0>;
- default-brightness-level = <6>;
-
- power-supply = <®_12v>;
- enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
- };
-
- cvbs-in {
- compatible = "composite-video-connector";
- label = "CVBS IN";
-
- port {
- cvbs_con: endpoint {
- remote-endpoint = <&adv7482_ain7>;
- };
- };
- };
-
- hdmi-in {
- compatible = "hdmi-connector";
- label = "HDMI IN";
- type = "a";
-
- port {
- hdmi_in_con: endpoint {
- remote-endpoint = <&adv7482_hdmi>;
- };
- };
- };
-
- hdmi0-out {
- compatible = "hdmi-connector";
- label = "HDMI0 OUT";
- type = "a";
-
- port {
- hdmi0_con: endpoint {
- remote-endpoint = <&rcar_dw_hdmi0_out>;
- };
- };
- };
-
- hdmi1-out {
- compatible = "hdmi-connector";
- label = "HDMI1 OUT";
- type = "a";
-
- port {
- hdmi1_con: endpoint {
- };
- };
- };
-
- keys {
- compatible = "gpio-keys";
-
- pinctrl-0 = <&keys_pins>;
- pinctrl-names = "default";
-
- key-1 {
- gpios = <&gpio5 17 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_1>;
- label = "SW4-1";
- wakeup-source;
- debounce-interval = <20>;
- };
- key-2 {
- gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_2>;
- label = "SW4-2";
- wakeup-source;
- debounce-interval = <20>;
- };
- key-3 {
- gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_3>;
- label = "SW4-3";
- wakeup-source;
- debounce-interval = <20>;
- };
- key-4 {
- gpios = <&gpio5 23 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_4>;
- label = "SW4-4";
- wakeup-source;
- debounce-interval = <20>;
- };
- key-a {
- gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_A>;
- label = "TSW0";
- wakeup-source;
- debounce-interval = <20>;
- };
- key-b {
- gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_B>;
- label = "TSW1";
- wakeup-source;
- debounce-interval = <20>;
- };
- key-c {
- gpios = <&gpio6 13 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_C>;
- label = "TSW2";
- wakeup-source;
- debounce-interval = <20>;
- };
- };
-
- reg_1p8v: regulator-1p8v {
- compatible = "regulator-fixed";
- regulator-name = "fixed-1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_3p3v: regulator-3p3v {
- compatible = "regulator-fixed";
- regulator-name = "fixed-3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_12v: regulator-12v {
- compatible = "regulator-fixed";
- regulator-name = "fixed-12V";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- sound_card: sound {
- compatible = "audio-graph-card";
-
- label = "rcar-sound";
-
- dais = <&rsnd_port0 /* ak4613 */
- &rsnd_port1 /* HDMI0 */
-#ifdef SOC_HAS_HDMI1
- &rsnd_port2 /* HDMI1 */
-#endif
- >;
- };
-
- vbus0_usb2: regulator-vbus0-usb2 {
- compatible = "regulator-fixed";
-
- regulator-name = "USB20_VBUS0";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
-
- gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vcc_sdhi0: regulator-vcc-sdhi0 {
- compatible = "regulator-fixed";
-
- regulator-name = "SDHI0 Vcc";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vccq_sdhi0: regulator-vccq-sdhi0 {
- compatible = "regulator-gpio";
-
- regulator-name = "SDHI0 VccQ";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
- gpios-states = <1>;
- states = <3300000 1>, <1800000 0>;
- };
-
- vcc_sdhi3: regulator-vcc-sdhi3 {
- compatible = "regulator-fixed";
-
- regulator-name = "SDHI3 Vcc";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vccq_sdhi3: regulator-vccq-sdhi3 {
- compatible = "regulator-gpio";
-
- regulator-name = "SDHI3 VccQ";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
- gpios-states = <1>;
- states = <3300000 1>, <1800000 0>;
- };
-
- vga {
- compatible = "vga-connector";
-
- port {
- vga_in: endpoint {
- remote-endpoint = <&adv7123_out>;
- };
- };
- };
-
- vga-encoder {
- compatible = "adi,adv7123";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7123_in: endpoint {
- remote-endpoint = <&du_out_rgb>;
- };
- };
- port@1 {
- reg = <1>;
- adv7123_out: endpoint {
- remote-endpoint = <&vga_in>;
- };
- };
- };
- };
-
- x12_clk: x12 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <24576000>;
- };
-
- /* External DU dot clocks */
- x21_clk: x21-clock {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <33000000>;
- };
-
- x22_clk: x22-clock {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <33000000>;
- };
-
- x23_clk: x23-clock {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <25000000>;
- };
-};
-
-&a57_0 {
- cpu-supply = <&dvfs>;
-};
-
-&audio_clk_a {
- clock-frequency = <22579200>;
-};
-
-&avb {
- pinctrl-0 = <&avb_pins>;
- pinctrl-names = "default";
- phy-handle = <&phy0>;
- tx-internal-delay-ps = <2000>;
- status = "okay";
-
- phy0: ethernet-phy@0 {
- compatible = "ethernet-phy-id0022.1622",
- "ethernet-phy-ieee802.3-c22";
- rxc-skew-ps = <1500>;
- reg = <0>;
- interrupt-parent = <&gpio2>;
- interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
- };
-};
-
-&csi20 {
- status = "okay";
-
- ports {
- port@0 {
- csi20_in: endpoint {
- clock-lanes = <0>;
- data-lanes = <1>;
- remote-endpoint = <&adv7482_txb>;
- };
- };
- };
-};
-
-&csi40 {
- status = "okay";
-
- ports {
- port@0 {
- csi40_in: endpoint {
- clock-lanes = <0>;
- data-lanes = <1 2 3 4>;
- remote-endpoint = <&adv7482_txa>;
- };
- };
- };
-};
-
-&du {
- pinctrl-0 = <&du_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- ports {
- port@0 {
- du_out_rgb: endpoint {
- remote-endpoint = <&adv7123_in>;
- };
- };
- };
-};
-
-&ehci0 {
- dr_mode = "otg";
- status = "okay";
-};
-
-&ehci1 {
- status = "okay";
-};
-
-&extalr_clk {
- clock-frequency = <32768>;
-};
-
-&hdmi0 {
- status = "okay";
-
- ports {
- port@1 {
- reg = <1>;
- rcar_dw_hdmi0_out: endpoint {
- remote-endpoint = <&hdmi0_con>;
- };
- };
- port@2 {
- reg = <2>;
- dw_hdmi0_snd_in: endpoint {
- remote-endpoint = <&rsnd_endpoint1>;
- };
- };
- };
-};
-
-#ifdef SOC_HAS_HDMI1
-&hdmi1 {
- status = "okay";
-
- ports {
- port@1 {
- reg = <1>;
- rcar_dw_hdmi1_out: endpoint {
- remote-endpoint = <&hdmi1_con>;
- };
- };
- port@2 {
- reg = <2>;
- dw_hdmi1_snd_in: endpoint {
- remote-endpoint = <&rsnd_endpoint2>;
- };
- };
- };
-};
-
-&hdmi1_con {
- remote-endpoint = <&rcar_dw_hdmi1_out>;
-};
-#endif /* SOC_HAS_HDMI1 */
-
-&hscif1 {
- pinctrl-0 = <&hscif1_pins>;
- pinctrl-names = "default";
-
- uart-has-rtscts;
- /* Please only enable hscif1 or scif1 */
- status = "okay";
-};
-
-&hsusb {
- dr_mode = "otg";
- status = "okay";
-};
-
-&i2c2 {
- pinctrl-0 = <&i2c2_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-
- clock-frequency = <100000>;
-
- ak4613: codec@10 {
- compatible = "asahi-kasei,ak4613";
- #sound-dai-cells = <0>;
- reg = <0x10>;
- clocks = <&rcar_sound 3>;
-
- asahi-kasei,in1-single-end;
- asahi-kasei,in2-single-end;
- asahi-kasei,out1-single-end;
- asahi-kasei,out2-single-end;
- asahi-kasei,out3-single-end;
- asahi-kasei,out4-single-end;
- asahi-kasei,out5-single-end;
- asahi-kasei,out6-single-end;
-
- port {
- ak4613_endpoint: endpoint {
- remote-endpoint = <&rsnd_endpoint0>;
- };
- };
- };
-
- cs2000: clk_multiplier@4f {
- #clock-cells = <0>;
- compatible = "cirrus,cs2000-cp";
- reg = <0x4f>;
- clocks = <&audio_clkout>, <&x12_clk>;
- clock-names = "clk_in", "ref_clk";
-
- assigned-clocks = <&cs2000>;
- assigned-clock-rates = <24576000>; /* 1/1 divide */
- };
-};
-
-&i2c4 {
- status = "okay";
-
- pca9654: gpio@20 {
- compatible = "onnn,pca9654";
- reg = <0x20>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- video-receiver@70 {
- compatible = "adi,adv7482";
- reg = <0x70 0x71 0x72 0x73 0x74 0x75
- 0x60 0x61 0x62 0x63 0x64 0x65>;
- reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater",
- "infoframe", "cbus", "cec", "sdp", "txa", "txb" ;
-
- interrupt-parent = <&gpio6>;
- interrupt-names = "intrq1", "intrq2";
- interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
- <31 IRQ_TYPE_LEVEL_LOW>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@7 {
- reg = <7>;
-
- adv7482_ain7: endpoint {
- remote-endpoint = <&cvbs_con>;
- };
- };
-
- port@8 {
- reg = <8>;
-
- adv7482_hdmi: endpoint {
- remote-endpoint = <&hdmi_in_con>;
- };
- };
-
- port@a {
- reg = <10>;
-
- adv7482_txa: endpoint {
- clock-lanes = <0>;
- data-lanes = <1 2 3 4>;
- remote-endpoint = <&csi40_in>;
- };
- };
-
- port@b {
- reg = <11>;
-
- adv7482_txb: endpoint {
- clock-lanes = <0>;
- data-lanes = <1>;
- remote-endpoint = <&csi20_in>;
- };
- };
- };
- };
-
- csa_vdd: adc@7c {
- compatible = "maxim,max9611";
- reg = <0x7c>;
-
- shunt-resistor-micro-ohms = <5000>;
- };
-
- csa_dvfs: adc@7f {
- compatible = "maxim,max9611";
- reg = <0x7f>;
-
- shunt-resistor-micro-ohms = <5000>;
- };
-};
-
-&i2c_dvfs {
- status = "okay";
-
- clock-frequency = <400000>;
-
- pmic: pmic@30 {
- pinctrl-0 = <&irq0_pins>;
- pinctrl-names = "default";
-
- compatible = "rohm,bd9571mwv";
- reg = <0x30>;
- interrupt-parent = <&intc_ex>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <2>;
- gpio-controller;
- #gpio-cells = <2>;
- rohm,ddr-backup-power = <0xf>;
- rohm,rstbmode-level;
-
- regulators {
- dvfs: dvfs {
- regulator-name = "dvfs";
- regulator-min-microvolt = <750000>;
- regulator-max-microvolt = <1030000>;
- regulator-boot-on;
- regulator-always-on;
- };
- };
- };
-
- eeprom@50 {
- compatible = "rohm,br24t01", "atmel,24c01";
- reg = <0x50>;
- pagesize = <8>;
- };
-};
-
-&ohci0 {
- dr_mode = "otg";
- status = "okay";
-};
-
-&ohci1 {
- status = "okay";
-};
-
-&pcie_bus_clk {
- clock-frequency = <100000000>;
-};
-
-&pciec0 {
- status = "okay";
-};
-
-&pciec1 {
- status = "okay";
-};
-
-&pfc {
- pinctrl-0 = <&scif_clk_pins>;
- pinctrl-names = "default";
-
- avb_pins: avb {
- mux {
- groups = "avb_link", "avb_mdio", "avb_mii";
- function = "avb";
- };
-
- pins_mdio {
- groups = "avb_mdio";
- drive-strength = <24>;
- };
-
- pins_mii_tx {
- pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
- "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
- drive-strength = <12>;
- };
- };
-
- du_pins: du {
- groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
- function = "du";
- };
-
- hscif1_pins: hscif1 {
- groups = "hscif1_data_a", "hscif1_ctrl_a";
- function = "hscif1";
- };
-
- i2c2_pins: i2c2 {
- groups = "i2c2_a";
- function = "i2c2";
- };
-
- irq0_pins: irq0 {
- groups = "intc_ex_irq0";
- function = "intc_ex";
- };
-
- keys_pins: keys {
- pins = "GP_5_17", "GP_5_20", "GP_5_22";
- bias-pull-up;
- };
-
- pwm1_pins: pwm1 {
- groups = "pwm1_a";
- function = "pwm1";
- };
-
- scif1_pins: scif1 {
- groups = "scif1_data_a", "scif1_ctrl";
- function = "scif1";
- };
-
- scif2_pins: scif2 {
- groups = "scif2_data_a";
- function = "scif2";
- };
-
- scif_clk_pins: scif_clk {
- groups = "scif_clk_a";
- function = "scif_clk";
- };
-
- sdhi0_pins: sd0 {
- groups = "sdhi0_data4", "sdhi0_ctrl";
- function = "sdhi0";
- power-source = <3300>;
- };
-
- sdhi0_pins_uhs: sd0_uhs {
- groups = "sdhi0_data4", "sdhi0_ctrl";
- function = "sdhi0";
- power-source = <1800>;
- };
-
- sdhi2_pins: sd2 {
- groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds";
- function = "sdhi2";
- power-source = <1800>;
- };
-
- sdhi3_pins: sd3 {
- groups = "sdhi3_data4", "sdhi3_ctrl";
- function = "sdhi3";
- power-source = <3300>;
- };
-
- sdhi3_pins_uhs: sd3_uhs {
- groups = "sdhi3_data4", "sdhi3_ctrl";
- function = "sdhi3";
- power-source = <1800>;
- };
-
- sound_pins: sound {
- groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
- function = "ssi";
- };
-
- sound_clk_pins: sound_clk {
- groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
- "audio_clkout_a", "audio_clkout3_a";
- function = "audio_clk";
- };
-
- usb0_pins: usb0 {
- groups = "usb0";
- function = "usb0";
- };
-
- usb1_pins: usb1 {
- mux {
- groups = "usb1";
- function = "usb1";
- };
-
- ovc {
- pins = "GP_6_27";
- bias-pull-up;
- };
-
- pwen {
- pins = "GP_6_26";
- bias-pull-down;
- };
- };
-
- usb30_pins: usb30 {
- groups = "usb30";
- function = "usb30";
- };
-};
-
-&pwm1 {
- pinctrl-0 = <&pwm1_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&rcar_sound {
- pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
- pinctrl-names = "default";
-
- /* audio_clkout0/1/2/3 */
- #clock-cells = <1>;
- clock-frequency = <12288000 11289600>;
-
- status = "okay";
-
- /* update <audio_clk_b> to <cs2000> */
- clocks = <&cpg CPG_MOD 1005>,
- <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
- <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
- <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
- <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
- <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
- <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
- <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
- <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
- <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
- <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
- <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
- <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
- <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
- <&audio_clk_a>, <&cs2000>,
- <&audio_clk_c>,
- <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
- rsnd_port0: port@0 {
- reg = <0>;
- rsnd_endpoint0: endpoint {
- remote-endpoint = <&ak4613_endpoint>;
-
- dai-format = "left_j";
- bitclock-master = <&rsnd_endpoint0>;
- frame-master = <&rsnd_endpoint0>;
-
- playback = <&ssi0>, <&src0>, <&dvc0>;
- capture = <&ssi1>, <&src1>, <&dvc1>;
- };
- };
-
- rsnd_port1: port@1 {
- reg = <1>;
- rsnd_endpoint1: endpoint {
- remote-endpoint = <&dw_hdmi0_snd_in>;
-
- dai-format = "i2s";
- bitclock-master = <&rsnd_endpoint1>;
- frame-master = <&rsnd_endpoint1>;
-
- playback = <&ssi2>;
- };
- };
-
-#ifdef SOC_HAS_HDMI1
- rsnd_port2: port@2 {
- reg = <2>;
- rsnd_endpoint2: endpoint {
- remote-endpoint = <&dw_hdmi1_snd_in>;
-
- dai-format = "i2s";
- bitclock-master = <&rsnd_endpoint2>;
- frame-master = <&rsnd_endpoint2>;
-
- playback = <&ssi3>;
- };
- };
-#endif /* SOC_HAS_HDMI1 */
- };
-};
-
-&rpc {
- /* Left disabled. To be enabled by firmware when unlocked. */
-
- flash@0 {
- compatible = "cypress,hyperflash", "cfi-flash";
- reg = <0>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- bootparam@0 {
- reg = <0x00000000 0x040000>;
- read-only;
- };
- bl2@40000 {
- reg = <0x00040000 0x140000>;
- read-only;
- };
- cert_header_sa6@180000 {
- reg = <0x00180000 0x040000>;
- read-only;
- };
- bl31@1c0000 {
- reg = <0x001c0000 0x040000>;
- read-only;
- };
- tee@200000 {
- reg = <0x00200000 0x440000>;
- read-only;
- };
- uboot@640000 {
- reg = <0x00640000 0x100000>;
- read-only;
- };
- dtb@740000 {
- reg = <0x00740000 0x080000>;
- };
- kernel@7c0000 {
- reg = <0x007c0000 0x1400000>;
- };
- user@1bc0000 {
- reg = <0x01bc0000 0x2440000>;
- };
- };
- };
-};
-
-&rwdt {
- timeout-sec = <60>;
- status = "okay";
-};
-
-#ifdef SOC_HAS_SATA
-&sata {
- status = "okay";
-};
-#endif /* SOC_HAS_SATA */
-
-&scif1 {
- pinctrl-0 = <&scif1_pins>;
- pinctrl-names = "default";
-
- uart-has-rtscts;
- /* Please only enable hscif1 or scif1 */
- /* status = "okay"; */
-};
-
-&scif2 {
- pinctrl-0 = <&scif2_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&scif_clk {
- clock-frequency = <14745600>;
-};
-
-&sdhi0 {
- pinctrl-0 = <&sdhi0_pins>;
- pinctrl-1 = <&sdhi0_pins_uhs>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <&vcc_sdhi0>;
- vqmmc-supply = <&vccq_sdhi0>;
- cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
- wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
- bus-width = <4>;
- sd-uhs-sdr50;
- sd-uhs-sdr104;
- status = "okay";
-};
-
-&sdhi2 {
- /* used for on-board 8bit eMMC */
- pinctrl-0 = <&sdhi2_pins>;
- pinctrl-1 = <&sdhi2_pins>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <®_3p3v>;
- vqmmc-supply = <®_1p8v>;
- bus-width = <8>;
- mmc-hs200-1_8v;
- mmc-hs400-1_8v;
- no-sd;
- no-sdio;
- non-removable;
- fixed-emmc-driver-type = <1>;
- full-pwr-cycle-in-suspend;
- status = "okay";
-};
-
-&sdhi3 {
- pinctrl-0 = <&sdhi3_pins>;
- pinctrl-1 = <&sdhi3_pins_uhs>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <&vcc_sdhi3>;
- vqmmc-supply = <&vccq_sdhi3>;
- cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
- wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
- bus-width = <4>;
- sd-uhs-sdr50;
- sd-uhs-sdr104;
- status = "okay";
-};
-
-&ssi1 {
- shared-pin;
-};
-
-&usb_extal_clk {
- clock-frequency = <50000000>;
-};
-
-&usb2_phy0 {
- pinctrl-0 = <&usb0_pins>;
- pinctrl-names = "default";
-
- vbus-supply = <&vbus0_usb2>;
- status = "okay";
-};
-
-&usb2_phy1 {
- pinctrl-0 = <&usb1_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&usb3_peri0 {
- phys = <&usb3_phy0>;
- phy-names = "usb";
-
- companion = <&xhci0>;
-
- status = "okay";
-};
-
-&usb3_phy0 {
- status = "okay";
-};
-
-&usb3s0_clk {
- clock-frequency = <100000000>;
-};
-
-&vin0 {
- status = "okay";
-};
-
-&vin1 {
- status = "okay";
-};
-
-&vin2 {
- status = "okay";
-};
-
-&vin3 {
- status = "okay";
-};
-
-&vin4 {
- status = "okay";
-};
-
-&vin5 {
- status = "okay";
-};
-
-&vin6 {
- status = "okay";
-};
-
-&vin7 {
- status = "okay";
-};
-
-&xhci0 {
- pinctrl-0 = <&usb30_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-#ifdef SOC_HAS_USB2_CH2
-&ehci2 {
- status = "okay";
-};
-
-&ohci2 {
- status = "okay";
-};
-
-&pfc {
- usb2_pins: usb2 {
- groups = "usb2";
- function = "usb2";
- };
-};
-
-&usb2_phy2 {
- pinctrl-0 = <&usb2_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-#endif /* SOC_HAS_USB2_CH2 */
diff --git a/arch/arm/dts/salvator-x.dtsi b/arch/arm/dts/salvator-x.dtsi
deleted file mode 100644
index ddee50e6463..00000000000
--- a/arch/arm/dts/salvator-x.dtsi
+++ /dev/null
@@ -1,29 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree Source for the Salvator-X board
- *
- * Copyright (C) 2015-2016 Renesas Electronics Corp.
- */
-
-#include "salvator-common.dtsi"
-
-/ {
- model = "Renesas Salvator-X board";
- compatible = "renesas,salvator-x";
-};
-
-&extal_clk {
- clock-frequency = <16666666>;
-};
-
-&i2c4 {
- clock-frequency = <400000>;
-
- versaclock5: clock-generator@6a {
- compatible = "idt,5p49v5923";
- reg = <0x6a>;
- #clock-cells = <1>;
- clocks = <&x23_clk>;
- clock-names = "xin";
- };
-};
diff --git a/arch/arm/dts/salvator-xs.dtsi b/arch/arm/dts/salvator-xs.dtsi
deleted file mode 100644
index 08b925624e1..00000000000
--- a/arch/arm/dts/salvator-xs.dtsi
+++ /dev/null
@@ -1,85 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree Source for the Salvator-X 2nd version board
- *
- * Copyright (C) 2015-2017 Renesas Electronics Corp.
- */
-
-#include "salvator-common.dtsi"
-
-/ {
- model = "Renesas Salvator-X 2nd version board";
- compatible = "renesas,salvator-xs";
-};
-
-&extal_clk {
- clock-frequency = <16640000>;
-};
-
-&i2c4 {
- clock-frequency = <400000>;
-
- versaclock6: clock-generator@6a {
- compatible = "idt,5p49v6901";
- reg = <0x6a>;
- #clock-cells = <1>;
- clocks = <&x23_clk>;
- clock-names = "xin";
- };
-};
-
-#ifdef SOC_HAS_SATA
-&pca9654 {
- pcie-sata-switch-hog {
- gpio-hog;
- gpios = <7 GPIO_ACTIVE_HIGH>;
- output-low; /* enable SATA by default */
- line-name = "PCIE/SATA switch";
- };
-};
-
-/* SW12-7 must be set 'Off' (MD12 set to 1) which is not the default! */
-#endif /* SOC_HAS_SATA */
-
-#ifdef SOC_HAS_USB2_CH3
-&ehci3 {
- dr_mode = "otg";
- status = "okay";
-};
-
-&hsusb3 {
- dr_mode = "otg";
- status = "okay";
-};
-
-&ohci3 {
- dr_mode = "otg";
- status = "okay";
-};
-
-&pfc {
- /*
- * - On Salvator-X[S], GP6_3[01] are connected to ADV7482 as irq pins
- * (when SW31 is the default setting on Salvator-XS).
- * - If SW31 is the default setting, you cannot use USB2.0 ch3 on
- * r8a77951 with Salvator-XS.
- * Hence the SW31 setting must be changed like 2) below.
- * 1) Default setting of SW31: ON-ON-OFF-OFF-OFF-OFF:
- * - Connect GP6_3[01] to ADV7842.
- * 2) Changed setting of SW31: OFF-OFF-ON-ON-ON-ON:
- * - Connect GP6_3[01] to BD082065 (USB2.0 ch3's host power).
- * - Connect GP6_{04,21} to ADV7842.
- */
- usb2_ch3_pins: usb2_ch3 {
- groups = "usb2_ch3";
- function = "usb2_ch3";
- };
-};
-
-&usb2_phy3 {
- pinctrl-0 = <&usb2_ch3_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-#endif /* SOC_HAS_USB2_CH3 */
diff --git a/arch/arm/dts/ulcb-audio-graph-card.dtsi b/arch/arm/dts/ulcb-audio-graph-card.dtsi
deleted file mode 100644
index 3be54df645e..00000000000
--- a/arch/arm/dts/ulcb-audio-graph-card.dtsi
+++ /dev/null
@@ -1,85 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree for ULCB + Audio Graph Card
- *
- * Copyright (C) 2022 Renesas Electronics Corp.
- */
-
-/*
- * (A) CPU0 <-----> ak4613
- * (B) CPU1 -----> HDMI
- *
- * (A) aplay -D plughw:0,0 xxx.wav
- * (B) aplay -D plughw:0,1 xxx.wav
- *
- * (A) arecord -D plughw:0,0 xxx.wav
- */
-
-/ {
- sound_card: sound {
- compatible = "audio-graph-card";
- label = "rcar-sound";
-
- dais = <&rsnd_port0 /* (A) CPU0 <-> ak4613 */
- &rsnd_port1 /* (B) CPU1 -> HDMI */
- >;
- };
-};
-
-&ak4613 {
- #sound-dai-cells = <0>;
-
- port {
- /*
- * (A) CPU0 <-> ak4613
- */
- ak4613_endpoint: endpoint {
- remote-endpoint = <&rsnd_for_ak4613>;
- };
- };
-};
-
-&hdmi0 {
- ports {
- port@2 {
- /*
- * (B) CPU1 -> HDMI
- */
- dw_hdmi0_snd_in: endpoint {
- remote-endpoint = <&rsnd_for_hdmi>;
- };
- };
- };
-};
-
-&rcar_sound {
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
- rsnd_port0: port@0 {
- /*
- * (A) CPU0 <-> ak4613
- */
- reg = <0>;
- rsnd_for_ak4613: endpoint {
- remote-endpoint = <&ak4613_endpoint>;
- bitclock-master;
- frame-master;
- playback = <&ssi0>, <&src0>, <&dvc0>;
- capture = <&ssi1>, <&src1>, <&dvc1>;
- };
- };
- rsnd_port1: port@1 {
- /*
- * (B) CPU1 -> HDMI
- */
- reg = <1>;
- rsnd_for_hdmi: endpoint {
- remote-endpoint = <&dw_hdmi0_snd_in>;
- bitclock-master;
- frame-master;
- playback = <&ssi2>;
- };
- };
- };
-};
diff --git a/arch/arm/dts/ulcb-audio-graph-card2.dtsi b/arch/arm/dts/ulcb-audio-graph-card2.dtsi
deleted file mode 100644
index 5ebec123584..00000000000
--- a/arch/arm/dts/ulcb-audio-graph-card2.dtsi
+++ /dev/null
@@ -1,26 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree for ULCB + Audio Graph Card2
- *
- * Copyright (C) 2022 Renesas Electronics Corp.
- */
-
-/*
- * (A) CPU0 <----> ak4613
- * (B) CPU1 ----> HDMI
- *
- * (A) aplay -D plughw:0,0 xxx.wav
- * (B) aplay -D plughw:0,1 xxx.wav
- *
- * (A) arecord -D plughw:0,0 xxx.wav
- */
-#include "ulcb-audio-graph-card.dtsi"
-
-&sound_card {
- compatible = "audio-graph-card2";
-
- /delete-property/ dais;
- links = <&rsnd_port0 /* (A) CPU0 <-> ak4613 */
- &rsnd_port1 /* (B) CPU1 -> HDMI */
- >;
-};
diff --git a/arch/arm/dts/ulcb.dtsi b/arch/arm/dts/ulcb.dtsi
deleted file mode 100644
index 0be2716659e..00000000000
--- a/arch/arm/dts/ulcb.dtsi
+++ /dev/null
@@ -1,509 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree Source for the R-Car Gen3 ULCB board
- *
- * Copyright (C) 2016 Renesas Electronics Corp.
- * Copyright (C) 2016 Cogent Embedded, Inc.
- */
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "Renesas R-Car Gen3 ULCB board";
-
- aliases {
- i2c0 = &i2c0;
- i2c1 = &i2c1;
- i2c2 = &i2c2;
- i2c3 = &i2c3;
- i2c4 = &i2c4;
- i2c5 = &i2c5;
- i2c6 = &i2c6;
- i2c7 = &i2c_dvfs;
- serial0 = &scif2;
- ethernet0 = &avb;
- mmc0 = &sdhi2;
- mmc1 = &sdhi0;
- };
-
- chosen {
- bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
- stdout-path = "serial0:115200n8";
- };
-
- audio_clkout: audio-clkout {
- /*
- * This is same as <&rcar_sound 0>
- * but needed to avoid cs2000/rcar_sound probe dead-lock
- */
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <12288000>;
- };
-
- hdmi0-out {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi0_con: endpoint {
- remote-endpoint = <&rcar_dw_hdmi0_out>;
- };
- };
- };
-
- keyboard {
- compatible = "gpio-keys";
-
- key-1 {
- linux,code = <KEY_1>;
- label = "SW3";
- wakeup-source;
- debounce-interval = <20>;
- gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
- };
- };
-
- leds {
- compatible = "gpio-leds";
-
- led5 {
- gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
- };
- led6 {
- gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
- };
- };
-
- reg_1p8v: regulator-1p8v {
- compatible = "regulator-fixed";
- regulator-name = "fixed-1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_3p3v: regulator-3p3v {
- compatible = "regulator-fixed";
- regulator-name = "fixed-3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- vcc_sdhi0: regulator-vcc-sdhi0 {
- compatible = "regulator-fixed";
-
- regulator-name = "SDHI0 Vcc";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vccq_sdhi0: regulator-vccq-sdhi0 {
- compatible = "regulator-gpio";
-
- regulator-name = "SDHI0 VccQ";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
- gpios-states = <1>;
- states = <3300000 1>, <1800000 0>;
- };
-
- x12_clk: x12 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <24576000>;
- };
-
- x23_clk: x23-clock {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <25000000>;
- };
-};
-
-&a57_0 {
- cpu-supply = <&dvfs>;
-};
-
-&audio_clk_a {
- clock-frequency = <22579200>;
-};
-
-&avb {
- pinctrl-0 = <&avb_pins>;
- pinctrl-names = "default";
- phy-handle = <&phy0>;
- tx-internal-delay-ps = <2000>;
- status = "okay";
-
- phy0: ethernet-phy@0 {
- compatible = "ethernet-phy-id0022.1622",
- "ethernet-phy-ieee802.3-c22";
- rxc-skew-ps = <1500>;
- reg = <0>;
- interrupt-parent = <&gpio2>;
- interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
- };
-};
-
-&du {
- status = "okay";
-};
-
-&ehci1 {
- status = "okay";
-};
-
-&extal_clk {
- clock-frequency = <16666666>;
-};
-
-&extalr_clk {
- clock-frequency = <32768>;
-};
-
-&hdmi0 {
- status = "okay";
-
- ports {
- port@1 {
- reg = <1>;
- rcar_dw_hdmi0_out: endpoint {
- remote-endpoint = <&hdmi0_con>;
- };
- };
- port@2 {
- reg = <2>;
- };
- };
-};
-
-&i2c2 {
- pinctrl-0 = <&i2c2_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-
- clock-frequency = <100000>;
-
- ak4613: codec@10 {
- compatible = "asahi-kasei,ak4613";
- reg = <0x10>;
- clocks = <&rcar_sound 3>;
-
- asahi-kasei,in1-single-end;
- asahi-kasei,in2-single-end;
- asahi-kasei,out1-single-end;
- asahi-kasei,out2-single-end;
- asahi-kasei,out3-single-end;
- asahi-kasei,out4-single-end;
- asahi-kasei,out5-single-end;
- asahi-kasei,out6-single-end;
- };
-
- cs2000: clk-multiplier@4f {
- #clock-cells = <0>;
- compatible = "cirrus,cs2000-cp";
- reg = <0x4f>;
- clocks = <&audio_clkout>, <&x12_clk>;
- clock-names = "clk_in", "ref_clk";
-
- assigned-clocks = <&cs2000>;
- assigned-clock-rates = <24576000>; /* 1/1 divide */
- };
-};
-
-&i2c4 {
- status = "okay";
-
- clock-frequency = <400000>;
-
- versaclock5: clock-generator@6a {
- compatible = "idt,5p49v5925";
- reg = <0x6a>;
- #clock-cells = <1>;
- clocks = <&x23_clk>;
- clock-names = "xin";
- };
-};
-
-&i2c_dvfs {
- status = "okay";
-
- clock-frequency = <400000>;
-
- pmic: pmic@30 {
- pinctrl-0 = <&irq0_pins>;
- pinctrl-names = "default";
-
- compatible = "rohm,bd9571mwv";
- reg = <0x30>;
- interrupt-parent = <&intc_ex>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <2>;
- gpio-controller;
- #gpio-cells = <2>;
- rohm,ddr-backup-power = <0xf>;
- rohm,rstbmode-pulse;
-
- regulators {
- dvfs: dvfs {
- regulator-name = "dvfs";
- regulator-min-microvolt = <750000>;
- regulator-max-microvolt = <1030000>;
- regulator-boot-on;
- regulator-always-on;
- };
- };
- };
-
- eeprom@50 {
- compatible = "rohm,br24t01", "atmel,24c01";
- reg = <0x50>;
- pagesize = <8>;
- };
-};
-
-&ohci1 {
- status = "okay";
-};
-
-&pfc {
- pinctrl-0 = <&scif_clk_pins>;
- pinctrl-names = "default";
-
- avb_pins: avb {
- mux {
- groups = "avb_link", "avb_mdio", "avb_mii";
- function = "avb";
- };
-
- pins_mdio {
- groups = "avb_mdio";
- drive-strength = <24>;
- };
-
- pins_mii_tx {
- pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
- "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
- drive-strength = <12>;
- };
- };
-
- i2c2_pins: i2c2 {
- groups = "i2c2_a";
- function = "i2c2";
- };
-
- irq0_pins: irq0 {
- groups = "intc_ex_irq0";
- function = "intc_ex";
- };
-
- scif2_pins: scif2 {
- groups = "scif2_data_a";
- function = "scif2";
- };
-
- scif_clk_pins: scif_clk {
- groups = "scif_clk_a";
- function = "scif_clk";
- };
-
- sdhi0_pins: sd0 {
- groups = "sdhi0_data4", "sdhi0_ctrl";
- function = "sdhi0";
- power-source = <3300>;
- };
-
- sdhi0_pins_uhs: sd0_uhs {
- groups = "sdhi0_data4", "sdhi0_ctrl";
- function = "sdhi0";
- power-source = <1800>;
- };
-
- sdhi2_pins: sd2 {
- groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds";
- function = "sdhi2";
- power-source = <1800>;
- };
-
- sound_pins: sound {
- groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
- function = "ssi";
- };
-
- sound_clk_pins: sound-clk {
- groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
- "audio_clkout_a", "audio_clkout3_a";
- function = "audio_clk";
- };
-
- usb1_pins: usb1 {
- groups = "usb1";
- function = "usb1";
- };
-};
-
-&rcar_sound {
- pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
- pinctrl-names = "default";
-
- /* audio_clkout0/1/2/3 */
- #clock-cells = <1>;
- clock-frequency = <12288000 11289600>;
-
- status = "okay";
-
- /* update <audio_clk_b> to <cs2000> */
- clocks = <&cpg CPG_MOD 1005>,
- <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
- <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
- <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
- <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
- <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
- <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
- <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
- <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
- <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
- <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
- <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
- <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
- <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
- <&audio_clk_a>, <&cs2000>,
- <&audio_clk_c>,
- <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
-};
-
-&rpc {
- /* Left disabled. To be enabled by firmware when unlocked. */
-
- flash@0 {
- compatible = "cypress,hyperflash", "cfi-flash";
- reg = <0>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- bootparam@0 {
- reg = <0x00000000 0x040000>;
- read-only;
- };
- bl2@40000 {
- reg = <0x00040000 0x140000>;
- read-only;
- };
- cert_header_sa6@180000 {
- reg = <0x00180000 0x040000>;
- read-only;
- };
- bl31@1c0000 {
- reg = <0x001c0000 0x040000>;
- read-only;
- };
- tee@200000 {
- reg = <0x00200000 0x440000>;
- read-only;
- };
- uboot@640000 {
- reg = <0x00640000 0x100000>;
- read-only;
- };
- dtb@740000 {
- reg = <0x00740000 0x080000>;
- };
- kernel@7c0000 {
- reg = <0x007c0000 0x1400000>;
- };
- user@1bc0000 {
- reg = <0x01bc0000 0x2440000>;
- };
- };
- };
-};
-
-&rwdt {
- timeout-sec = <60>;
- status = "okay";
-};
-
-&scif2 {
- pinctrl-0 = <&scif2_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&scif_clk {
- clock-frequency = <14745600>;
-};
-
-&sdhi0 {
- pinctrl-0 = <&sdhi0_pins>;
- pinctrl-1 = <&sdhi0_pins_uhs>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <&vcc_sdhi0>;
- vqmmc-supply = <&vccq_sdhi0>;
- cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
- bus-width = <4>;
- sd-uhs-sdr50;
- sd-uhs-sdr104;
- status = "okay";
-};
-
-&sdhi2 {
- /* used for on-board 8bit eMMC */
- pinctrl-0 = <&sdhi2_pins>;
- pinctrl-1 = <&sdhi2_pins>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <®_3p3v>;
- vqmmc-supply = <®_1p8v>;
- bus-width = <8>;
- mmc-hs200-1_8v;
- mmc-hs400-1_8v;
- no-sd;
- no-sdio;
- non-removable;
- full-pwr-cycle-in-suspend;
- status = "okay";
-};
-
-&ssi1 {
- shared-pin;
-};
-
-&usb2_phy1 {
- pinctrl-0 = <&usb1_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-
-/*
- * For sound-test.
- *
- * We can switch Audio Card for testing
- *
- * #include "ulcb-simple-audio-card.dtsi"
- * #include "ulcb-simple-audio-card-mix+split.dtsi"
- * #include "ulcb-audio-graph-card.dtsi"
- * #include "ulcb-audio-graph-card-mix+split.dtsi"
- * #include "ulcb-audio-graph-card2-mix+split.dtsi"
- */
-#include "ulcb-audio-graph-card2.dtsi"
--
2.43.0
