October 2022 - U-Boot

PSCI: prefetch abort with Mainline linux (even with rockchip u-boot)
by Jagan Teki 13 Sep '23

13 Sep '23

Hi Kever and Heiko, Rockchip 32-bit SoC, like rv1126 seems to depend on PSCI to bring SMP in linux. With rockchip u-boot and Mainline U-Boot the psci in linux-next triggers the abort. (note that I have added rockchip_smcc and enabled PSCI in u-boot) [ 0.000000] Booting Linux on physical CPU 0xf00 [ 0.000000] Linux version 6.1.0-rc1-00029-gb09e57e6064a (j@j-ThinkPad-E14-Gen-2) (arm-linux-gnueabihf-gcc (GCC) 11.0.1 20210310 (experimental) [master revision 5987d8a79cda1069c774e5c302d5597310270026], GNU ld (Linaro_Binutils-2021.03) 2.36.50.20210310) #12 SMP Sat Oct 22 19:44:56 IST 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Edgeble Neu2 IO Board [ 0.000000] earlycon: uart8250 at MMIO32 0xff570000 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] Bad mode in prefetch abort handler detected [ 0.000000] Internal error: Oops - bad mode: 0 [#1] SMP ARM [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 6.1.0-rc1-00029-gb09e57e6064a #12 [ 0.000000] Hardware name: Generic DT based system [ 0.000000] PC is at 0x133fd468 [ 0.000000] LR is at __invoke_psci_fn_smc+0x38/0x58 [ 0.000000] pc : [<133fd468>] lr : [<c0eb20f0>] psr: 600001d6 [ 0.000000] sp : c1e01e68 ip : c1e01ec0 fp : 80000200 [ 0.000000] r10: c1e01f58 r9 : 7fffffff r8 : c1e09410 [ 0.000000] r7 : 00000000 r6 : 00000000 r5 : 00000000 r4 : 00000000 [ 0.000000] r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : 84000000 [ 0.000000] Flags: nZCv IRQs off FIQs off Mode MON_32 ISA ARM Segment none [ 0.000000] Control: 10c5387d Table: 0020406a DAC: c1e09980 [ 0.000000] Register r0 information: non-paged memory [ 0.000000] Register r1 information: NULL pointer [ 0.000000] Register r2 information: NULL pointer [ 0.000000] Register r3 information: NULL pointer [ 0.000000] Register r4 information: NULL pointer [ 0.000000] Register r5 information: NULL pointer [ 0.000000] Register r6 information: NULL pointer [ 0.000000] Register r7 information: NULL pointer [ 0.000000] Register r8 information: non-slab/vmalloc memory [ 0.000000] Register r9 information: non-paged memory [ 0.000000] Register r10 information: non-slab/vmalloc memory [ 0.000000] Register r11 information: non-paged memory [ 0.000000] Register r12 information: non-slab/vmalloc memory [ 0.000000] Process swapper (pid: 0, stack limit = 0x(ptrval)) [ 0.000000] Stack: (0xc1e01e68 to 0xc1e02000) [ 0.000000] 1e60: 84000000 00000000 00000000 00000000 00000000 00000000 [ 0.000000] 1e80: 00000000 00000000 c1e09410 7fffffff c1e01f58 80000200 c1e01ec0 c1e01e68 [ 0.000000] 1ea0: c0eb20f0 133fd468 600001d6 ffffffff c1e09980 00000000 c20891c0 c1b1c168 [ 0.000000] 1ec0: 00000000 00000000 00000000 00000000 c1e01edc 00000000 c20891c0 c1245ac8 [ 0.000000] 1ee0: ff8005a8 00000000 c1d2fca0 00000000 eefea2fc c1c93594 eefea2fc c1e09980 [ 0.000000] 1f00: c20891c0 c1b1c168 c1e09410 c1c93a10 eefea2fc c1c939d8 c1d2fbdc 00000000 [ 0.000000] 1f20: 7fffffff c1caf854 c1e0afa0 c1c04c44 00000000 c1e01f4c c1e01f50 00000000 [ 0.000000] 1f40: c1e09980 c198cfec c1e01f9c 00000000 80000000 c1e09980 ffffffff ffffffff [ 0.000000] 1f60: c2089064 08300000 410fc075 10c5387d 00000000 c039de88 c1e01f9c 00000000 [ 0.000000] 1f80: c1e09980 c1c00420 c1e04ec0 c1e09980 c2089064 08300000 410fc075 10c5387d [ 0.000000] 1fa0: 00000000 c1c00b08 00000000 00000000 00000000 00000000 00000000 00000000 [ 0.000000] 1fc0: 00000000 c1cc8a6c 00000000 00000000 00000000 c1c00420 00000051 10c0387d [ 0.000000] 1fe0: 00000000 08300000 410fc075 10c5387d 00000000 00000000 00000000 00000000 [ 0.000000] __invoke_psci_fn_smc from 0xc1e01e68 [ 0.000000] Code: bad PC value Any comments? Thanks, Jagan.

2 1

[PATCH v3 0/9] New boards support: db845c and qcs404-evb
by Sumit Garg 11 Sep '23

11 Sep '23

Add support for two new boards db845c and qcs404-evb: - db845c is a 96boards compliant platform aka RB3 based on Qualcomm SDM845 SoC. - qcs404-evb is an evaluation board from Qualcomm based on QCS404 SoC. Both these platforms have one thing in common that u-boot is chain-loaded in 64-bit mode via Android Boot Loader (ABL) which is an EFI application. For further details on chain-loading refer to platform specific documentation: - doc/board/qualcomm/sdm845.rst - doc/board/qualcomm/qcs404.rst Changes in v3: - Add clocks re-initialization for UART and eMMC for qcs404-evb. - Pick up Ramon's review tag for patches 1-7. Changes in v2: - Added patch #1 to fix DT node overrides in starqltechn-uboot.dtsi. - Updated patch #2 commit description. - Fixed a typo (s/96Board/96Boards/) in patch #5. Sumit Garg (9): board: starqltechn: Align DT node overrides with sdm845.dtsi arm64: dts: sdm845: Remove redundant u-boot DT properties clocks: sdm845: Import qcom,gcc-sdm845.h uart: sdm845: Fix debug UART pinmux board: qualcomm: Add support for dragonboard845c mmc: msm_sdhci: Add SDCC version 5.0.0 support pinctrl: qcom: Add pinctrl driver for QCS404 SoC clocks: qcom: Add clock driver for QCS404 SoC board: qualcomm: Add support for QCS404 EVB arch/arm/dts/Makefile | 1 + arch/arm/dts/dragonboard845c-uboot.dtsi | 37 +++ arch/arm/dts/dragonboard845c.dts | 44 ++++ arch/arm/dts/qcs404-evb-uboot.dtsi | 24 ++ arch/arm/dts/qcs404-evb.dts | 81 ++++++ arch/arm/dts/sdm845.dtsi | 8 +- arch/arm/dts/starqltechn-uboot.dtsi | 18 +- arch/arm/dts/starqltechn.dts | 2 +- arch/arm/mach-snapdragon/Kconfig | 25 ++ arch/arm/mach-snapdragon/Makefile | 3 + arch/arm/mach-snapdragon/clock-qcs404.c | 79 ++++++ arch/arm/mach-snapdragon/clock-sdm845.c | 3 +- arch/arm/mach-snapdragon/clock-snapdragon.c | 1 + .../include/mach/sysmap-qcs404.h | 40 +++ arch/arm/mach-snapdragon/pinctrl-qcs404.c | 55 ++++ arch/arm/mach-snapdragon/pinctrl-snapdragon.c | 1 + arch/arm/mach-snapdragon/pinctrl-snapdragon.h | 1 + arch/arm/mach-snapdragon/sysmap-qcs404.c | 31 +++ board/qualcomm/dragonboard845c/Kconfig | 12 + board/qualcomm/dragonboard845c/MAINTAINERS | 6 + board/qualcomm/dragonboard845c/Makefile | 9 + board/qualcomm/dragonboard845c/db845c.its | 63 +++++ .../dragonboard845c/dragonboard845c.c | 9 + board/qualcomm/qcs404-evb/Kconfig | 15 ++ board/qualcomm/qcs404-evb/MAINTAINERS | 6 + board/qualcomm/qcs404-evb/Makefile | 6 + board/qualcomm/qcs404-evb/qcs404-evb.c | 33 +++ board/qualcomm/qcs404-evb/qcs404-evb.its | 64 +++++ configs/dragonboard845c_defconfig | 28 ++ configs/qcs404evb_defconfig | 39 +++ doc/board/qualcomm/index.rst | 1 + doc/board/qualcomm/qcs404.rst | 79 ++++++ doc/board/qualcomm/sdm845.rst | 100 ++++++- drivers/mmc/msm_sdhci.c | 96 ++++--- include/configs/dragonboard845c.h | 28 ++ include/configs/qcs404-evb.h | 27 ++ include/dt-bindings/clock/qcom,gcc-qcs404.h | 180 +++++++++++++ include/dt-bindings/clock/qcom,gcc-sdm845.h | 246 ++++++++++++++++++ 38 files changed, 1439 insertions(+), 62 deletions(-) create mode 100644 arch/arm/dts/dragonboard845c-uboot.dtsi create mode 100644 arch/arm/dts/dragonboard845c.dts create mode 100644 arch/arm/dts/qcs404-evb-uboot.dtsi create mode 100644 arch/arm/dts/qcs404-evb.dts create mode 100644 arch/arm/mach-snapdragon/clock-qcs404.c create mode 100644 arch/arm/mach-snapdragon/include/mach/sysmap-qcs404.h create mode 100644 arch/arm/mach-snapdragon/pinctrl-qcs404.c create mode 100644 arch/arm/mach-snapdragon/sysmap-qcs404.c create mode 100644 board/qualcomm/dragonboard845c/Kconfig create mode 100644 board/qualcomm/dragonboard845c/MAINTAINERS create mode 100644 board/qualcomm/dragonboard845c/Makefile create mode 100644 board/qualcomm/dragonboard845c/db845c.its create mode 100644 board/qualcomm/dragonboard845c/dragonboard845c.c create mode 100644 board/qualcomm/qcs404-evb/Kconfig create mode 100644 board/qualcomm/qcs404-evb/MAINTAINERS create mode 100644 board/qualcomm/qcs404-evb/Makefile create mode 100644 board/qualcomm/qcs404-evb/qcs404-evb.c create mode 100644 board/qualcomm/qcs404-evb/qcs404-evb.its create mode 100644 configs/dragonboard845c_defconfig create mode 100644 configs/qcs404evb_defconfig create mode 100644 doc/board/qualcomm/qcs404.rst create mode 100644 include/configs/dragonboard845c.h create mode 100644 include/configs/qcs404-evb.h create mode 100644 include/dt-bindings/clock/qcom,gcc-qcs404.h create mode 100644 include/dt-bindings/clock/qcom,gcc-sdm845.h -- 2.25.1

5 32

[PATCH v3 00/13] Fuzzing and ASAN for sandbox
by Andrew Scull 28 Aug '23

28 Aug '23

This series introduces ASAN and a basic fuzzing infrastructure that works with sandbox. The example fuzz test towards the end of the series will find something pretty quickly. That something is fixed by the series "virtio: Harden and test vring" that needs to be applied for the final patch in this series. There is some refactoring to stop using '.' prefixed sections. ELF defines sections with names that contain anything that isn't alphanumeric or an underscore as being for system use which means clang's ASAN instrumentation happily add redzones between the contained objects. That's not what we want for things like linker lists where the linker script has carefully placed the sections contiguously. By renaming the sections, clang sees them as user sections and doesn't add instrumentation. ASAN is left disabled by default as there are still some tests that it triggers on and will need some more investigation to fix. It can be enabled with CONFIG_ASAN or passing `-a ASAN` to buildman. I abandonded the previous attempts to refactor sandbox EFI and getopt declaration as the changes resulted in problems out of the scope of this CL. I haven't tried to understand what EFI on sandbox should look like, but I have found that the linker list implementation is very brittle when up against compiler optimisation since ef123c5253 started to use static, zero-length arrays to mark the beginning and end of lists but the compiler see this as something it can get rid of. >From v1: - corrected handling of EFI symbols by sandbox linker script - per comments, some renaming and explaining - dropped RFC for dlmalloc ASAN instrumentation (work required to improve it) - added patch to reduce logging noise in fuzzer >From v2: - remove sandbox EFI and getopt refactoring, they obstruct the series - resolve a couple more ASAN errors - fix LTO, xtensa and MIPS builds - add ASAN build targets for CI Andrew Scull (13): serial: sandbox: Fix buffer underflow in puts sandbox: Rename EFI runtime sections sandbox: Rename getopt sections linker_lists: Rename sections to remove . prefix sandbox: Add support for Address Sanitizer test/py: test_stackprotector: Disable for ASAN CI: Azure: Build with ASAN enabled fuzzing_engine: Add fuzzing engine uclass test: fuzz: Add framework for fuzzing sandbox: Decouple program entry from sandbox init sandbox: Add libfuzzer integration sandbox: Implement fuzzing engine driver fuzz: virtio: Add fuzzer for vring .azure-pipelines.yml | 6 ++ Kconfig | 16 ++++ arch/Kconfig | 2 + arch/arc/cpu/u-boot.lds | 4 +- arch/arm/config.mk | 4 +- arch/arm/cpu/arm926ejs/sunxi/u-boot-spl.lds | 4 +- arch/arm/cpu/armv7/sunxi/u-boot-spl.lds | 4 +- arch/arm/cpu/armv8/u-boot-spl.lds | 4 +- arch/arm/cpu/armv8/u-boot.lds | 4 +- arch/arm/cpu/u-boot-spl.lds | 4 +- arch/arm/cpu/u-boot.lds | 6 +- arch/arm/mach-at91/arm926ejs/u-boot-spl.lds | 2 +- arch/arm/mach-at91/armv7/u-boot-spl.lds | 2 +- arch/arm/mach-omap2/u-boot-spl.lds | 4 +- arch/arm/mach-orion5x/u-boot-spl.lds | 4 +- arch/arm/mach-rockchip/u-boot-tpl-v8.lds | 4 +- arch/arm/mach-zynq/u-boot-spl.lds | 4 +- arch/arm/mach-zynq/u-boot.lds | 4 +- arch/m68k/cpu/u-boot.lds | 4 +- arch/microblaze/cpu/u-boot-spl.lds | 4 +- arch/microblaze/cpu/u-boot.lds | 4 +- arch/mips/config.mk | 2 +- arch/mips/cpu/u-boot-spl.lds | 4 +- arch/mips/cpu/u-boot.lds | 4 +- arch/nios2/cpu/u-boot.lds | 4 +- arch/powerpc/cpu/mpc83xx/u-boot.lds | 4 +- arch/powerpc/cpu/mpc85xx/u-boot-spl.lds | 4 +- arch/powerpc/cpu/mpc85xx/u-boot.lds | 4 +- arch/riscv/cpu/u-boot-spl.lds | 4 +- arch/riscv/cpu/u-boot.lds | 4 +- arch/sandbox/config.mk | 21 ++++- arch/sandbox/cpu/os.c | 76 +++++++++++++++++ arch/sandbox/cpu/start.c | 2 +- arch/sandbox/cpu/u-boot-spl.lds | 10 +-- arch/sandbox/cpu/u-boot.lds | 32 ++++---- arch/sandbox/dts/test.dts | 4 + arch/sandbox/include/asm/fuzzing_engine.h | 25 ++++++ arch/sandbox/include/asm/getopt.h | 2 +- arch/sandbox/include/asm/main.h | 18 ++++ arch/sandbox/include/asm/sections.h | 4 +- arch/sandbox/lib/sections.c | 8 +- arch/sh/cpu/u-boot.lds | 4 +- arch/x86/cpu/u-boot-64.lds | 6 +- arch/x86/cpu/u-boot-spl.lds | 6 +- arch/x86/cpu/u-boot.lds | 6 +- arch/x86/lib/elf_ia32_efi.lds | 4 +- arch/x86/lib/elf_x86_64_efi.lds | 4 +- arch/xtensa/cpu/u-boot.lds | 4 +- arch/xtensa/include/asm/ldscript.h | 13 ++- board/compulab/cm_t335/u-boot.lds | 4 +- board/cssi/MCR3000/u-boot.lds | 4 +- .../davinci/da8xxevm/u-boot-spl-da850evm.lds | 2 +- board/qualcomm/dragonboard820c/u-boot.lds | 4 +- board/samsung/common/exynos-uboot-spl.lds | 4 +- board/synopsys/iot_devkit/u-boot.lds | 4 +- board/ti/am335x/u-boot.lds | 4 +- board/vscom/baltos/u-boot.lds | 4 +- doc/api/linker_lists.rst | 22 ++--- doc/develop/commands.rst | 4 +- doc/develop/driver-model/of-plat.rst | 4 +- drivers/Kconfig | 2 + drivers/Makefile | 1 + drivers/fuzz/Kconfig | 17 ++++ drivers/fuzz/Makefile | 8 ++ drivers/fuzz/fuzzing_engine-uclass.c | 28 +++++++ drivers/fuzz/sandbox_fuzzing_engine.c | 35 ++++++++ drivers/serial/sandbox.c | 2 +- include/dm/uclass-id.h | 1 + include/fuzzing_engine.h | 51 ++++++++++++ include/linker_lists.h | 18 ++-- include/test/fuzz.h | 51 ++++++++++++ test/Makefile | 1 + test/fuzz/Makefile | 8 ++ test/fuzz/cmd_fuzz.c | 82 +++++++++++++++++++ test/fuzz/virtio.c | 72 ++++++++++++++++ test/py/tests/test_stackprotector.py | 1 + tools/mips-relocs.c | 9 +- 77 files changed, 673 insertions(+), 151 deletions(-) create mode 100644 arch/sandbox/include/asm/fuzzing_engine.h create mode 100644 arch/sandbox/include/asm/main.h create mode 100644 drivers/fuzz/Kconfig create mode 100644 drivers/fuzz/Makefile create mode 100644 drivers/fuzz/fuzzing_engine-uclass.c create mode 100644 drivers/fuzz/sandbox_fuzzing_engine.c create mode 100644 include/fuzzing_engine.h create mode 100644 include/test/fuzz.h create mode 100644 test/fuzz/Makefile create mode 100644 test/fuzz/cmd_fuzz.c create mode 100644 test/fuzz/virtio.c -- 2.36.1.124.g0e6072fb45-goog

4 17

[PATCH 0/6] introduce Arm FF-A support
by abdellatif.elkhlifi＠arm.com 17 Aug '23

17 Aug '23

From: Abdellatif El Khlifi <abdellatif.elkhlifi(a)arm.com> This patchset adds support for Arm FF-A (Arm Firmware Framework for Armv8-A v1.0). FF-A support is generic by design and can be used by any Arm platform. The features added are as follows: 1/ FF-A device driver 2/ armffa command 3/ FF-A Sandbox driver 4/ FF-A Sandbox test cases 5/ FF-A MM communication The suggested design sees FF-A as a data bus allowing data exchange with the firmware running under TrustZone HW (such as Optee). The same approach was followed in the FF-A driver in Linux kernel (https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/dri… u-boot boards using FF-A can provide a device tree node in a <board>-u-boot.dtsi file. Since the node can not be hosted in Linux device tree, we suggest using u-boot device tree. As a use case, we will send a commit enabling FF-A for the Corstone-1000 platform and providing the FF-A node in u-boot.dtsi files. Corstone-1000: https://lore.kernel.org/u-boot/20220322104118.573537-1-rui.silva@linaro.org/ Cc: Tom Rini <trini(a)konsulko.com> Abdellatif El Khlifi (6): arm_ffa: introduce Arm FF-A low-level driver arm_ffa: introduce armffa command arm_ffa: introduce the FF-A Sandbox driver arm_ffa: introduce Sandbox test cases for UCLASS_FFA arm_ffa: introduce armffa command Sandbox test arm_ffa: introduce FF-A MM communication MAINTAINERS | 15 + arch/arm/cpu/armv8/cache.S | 16 + arch/arm/cpu/armv8/cache_v8.c | 3 +- arch/arm/cpu/armv8/smccc-call.S | 27 + arch/arm/lib/asm-offsets.c | 6 + arch/sandbox/dts/sandbox.dtsi | 10 + arch/sandbox/dts/test.dts | 10 + cmd/Kconfig | 10 + cmd/Makefile | 2 + cmd/armffa.c | 266 +++++ common/board_r.c | 7 + configs/sandbox64_defconfig | 2 + configs/sandbox_defconfig | 2 + doc/arch/sandbox.rst | 1 + drivers/Kconfig | 2 + drivers/Makefile | 1 + drivers/arm-ffa/Kconfig | 32 + drivers/arm-ffa/Makefile | 7 + drivers/arm-ffa/arm-ffa-uclass.c | 102 ++ drivers/arm-ffa/arm_ffa_prv.h | 200 ++++ drivers/arm-ffa/core.c | 1463 +++++++++++++++++++++++++ drivers/arm-ffa/sandbox.c | 735 +++++++++++++ drivers/arm-ffa/sandbox_arm_ffa_prv.h | 128 +++ include/arm_ffa.h | 197 ++++ include/arm_ffa_helper.h | 45 + include/dm/uclass-id.h | 1 + include/linux/arm-smccc.h | 28 +- include/mm_communication.h | 4 +- include/sandbox_arm_ffa.h | 31 + include/sandbox_arm_ffa_helper.h | 26 + lib/Kconfig | 1 + lib/Makefile | 1 + lib/arm-ffa/Kconfig | 6 + lib/arm-ffa/Makefile | 9 + lib/arm-ffa/arm_ffa_helper.c | 188 ++++ lib/arm-ffa/sandbox_arm_ffa_helper.c | 23 + lib/efi_loader/Kconfig | 14 +- lib/efi_loader/efi_boottime.c | 17 + lib/efi_loader/efi_variable_tee.c | 294 ++++- test/cmd/Makefile | 1 + test/cmd/armffa.c | 33 + test/cmd/armffa.h | 13 + test/dm/Makefile | 1 + test/dm/ffa.c | 424 +++++++ test/dm/ffa.h | 22 + 45 files changed, 4415 insertions(+), 11 deletions(-) create mode 100644 cmd/armffa.c create mode 100644 drivers/arm-ffa/Kconfig create mode 100644 drivers/arm-ffa/Makefile create mode 100644 drivers/arm-ffa/arm-ffa-uclass.c create mode 100644 drivers/arm-ffa/arm_ffa_prv.h create mode 100644 drivers/arm-ffa/core.c create mode 100644 drivers/arm-ffa/sandbox.c create mode 100644 drivers/arm-ffa/sandbox_arm_ffa_prv.h create mode 100644 include/arm_ffa.h create mode 100644 include/arm_ffa_helper.h create mode 100644 include/sandbox_arm_ffa.h create mode 100644 include/sandbox_arm_ffa_helper.h create mode 100644 lib/arm-ffa/Kconfig create mode 100644 lib/arm-ffa/Makefile create mode 100644 lib/arm-ffa/arm_ffa_helper.c create mode 100644 lib/arm-ffa/sandbox_arm_ffa_helper.c create mode 100644 test/cmd/armffa.c create mode 100644 test/cmd/armffa.h create mode 100644 test/dm/ffa.c create mode 100644 test/dm/ffa.h -- 2.17.1

12 477

[PATCH] odroid_xu3: Fix board environment variable
by Tom Rini 14 Aug '23

14 Aug '23

When migrating CONFIG_CONS_INDEX to Kconfig, on this platform we changed what "board" evaluated to in the environment. This in turn meant that we would no longer try and find the correct fdtfile via the normal distro boot logic. Fix this by overriding board in the default environment, as done on other platforms where CONFIG_SYS_BOARD is not what we want to be in the board environment variable. Fixes: f76750d11133 ("Convert CONFIG_CONS_INDEX et al to Kconfig") Reported-by: Gabriel Hojda <ghojda(a)yo2urs.ro> Tested-by: Gabriel Hojda <ghojda(a)yo2urs.ro> Signed-off-by: Tom Rini <trini(a)konsulko.com> --- include/configs/odroid_xu3.h | 1 + 1 file changed, 1 insertion(+) diff --git a/include/configs/odroid_xu3.h b/include/configs/odroid_xu3.h index eb35d7b4ae2d..360815bc03ee 100644 --- a/include/configs/odroid_xu3.h +++ b/include/configs/odroid_xu3.h @@ -86,6 +86,7 @@ "rootfstype=ext4\0" \ "console=console=ttySAC2,115200n8\0" \ "fdtfile=exynos5422-odroidxu3.dtb\0" \ + "board=odroid\0" \ "board_name=odroidxu3\0" \ "mmcbootdev=0\0" \ "mmcrootdev=0\0" \ -- 2.25.1

2 3

[PATCH] freescale: Remove Rajesh Bhagat MAINTAINERS
by Sean Anderson 03 Aug '23

03 Aug '23

Rajesh's email bounces. Remove his email from all boards he maintains. Fortunately, he has co-maintainers on most boards. I have taken the liberty of volunteering Pramod to maintain the LS1012AFRDM, since he also maintains the LS1012AFRWY. Let me know if the board should be orphaned instead. Signed-off-by: Sean Anderson <sean.anderson(a)seco.com> --- board/freescale/ls1012afrdm/MAINTAINERS | 2 +- board/freescale/ls1012aqds/MAINTAINERS | 1 - board/freescale/ls1012ardb/MAINTAINERS | 1 - board/freescale/ls1028a/MAINTAINERS | 2 -- board/freescale/ls1043aqds/MAINTAINERS | 1 - board/freescale/ls1043ardb/MAINTAINERS | 1 - board/freescale/ls1046aqds/MAINTAINERS | 1 - board/freescale/ls1046ardb/MAINTAINERS | 1 - board/freescale/ls1088a/MAINTAINERS | 2 -- board/freescale/ls2080aqds/MAINTAINERS | 1 - board/freescale/ls2080ardb/MAINTAINERS | 1 - 11 files changed, 1 insertion(+), 13 deletions(-) diff --git a/board/freescale/ls1012afrdm/MAINTAINERS b/board/freescale/ls1012afrdm/MAINTAINERS index 5fc7e93850e..89d1085b00b 100644 --- a/board/freescale/ls1012afrdm/MAINTAINERS +++ b/board/freescale/ls1012afrdm/MAINTAINERS @@ -1,5 +1,5 @@ LS1012AFRDM BOARD -M: Rajesh Bhagat <rajesh.bhagat(a)nxp.com> +M: Pramod Kumar <pramod.kumar_1(a)nxp.com> S: Maintained F: board/freescale/ls1012afrdm/ F: include/configs/ls1012afrdm.h diff --git a/board/freescale/ls1012aqds/MAINTAINERS b/board/freescale/ls1012aqds/MAINTAINERS index c1bb8d51508..eabf5805765 100644 --- a/board/freescale/ls1012aqds/MAINTAINERS +++ b/board/freescale/ls1012aqds/MAINTAINERS @@ -1,5 +1,4 @@ LS1012AQDS BOARD -M: Rajesh Bhagat <rajesh.bhagat(a)nxp.com> M: Pramod Kumar <pramod.kumar_1(a)nxp.com> S: Maintained F: board/freescale/ls1012aqds/ diff --git a/board/freescale/ls1012ardb/MAINTAINERS b/board/freescale/ls1012ardb/MAINTAINERS index b0c008b5fc9..ce2f9a16cc7 100644 --- a/board/freescale/ls1012ardb/MAINTAINERS +++ b/board/freescale/ls1012ardb/MAINTAINERS @@ -1,5 +1,4 @@ LS1012ARDB BOARD -M: Rajesh Bhagat <rajesh.bhagat(a)nxp.com> M: Pramod Kumar <pramod.kumar_1(a)nxp.com> S: Maintained F: board/freescale/ls1012ardb/ diff --git a/board/freescale/ls1028a/MAINTAINERS b/board/freescale/ls1028a/MAINTAINERS index 9e7b0697ff6..551f6a08651 100644 --- a/board/freescale/ls1028a/MAINTAINERS +++ b/board/freescale/ls1028a/MAINTAINERS @@ -1,5 +1,4 @@ LS1028AQDS BOARD -M: Rajesh Bhagat <rajesh.bhagat(a)nxp.com> M: Tang Yuantian <andy.tang(a)nxp.com> S: Maintained F: board/freescale/ls1028a/ @@ -9,7 +8,6 @@ F: configs/ls1028aqds_tfa_defconfig F: configs/ls1028aqds_tfa_lpuart_defconfig LS1028ARDB BOARD -M: Rajesh Bhagat <rajesh.bhagat(a)nxp.com> M: Tang Yuantian <andy.tang(a)nxp.com> S: Maintained F: board/freescale/ls1028a/ diff --git a/board/freescale/ls1043aqds/MAINTAINERS b/board/freescale/ls1043aqds/MAINTAINERS index 9fb6cc85cd0..f7420ecd303 100644 --- a/board/freescale/ls1043aqds/MAINTAINERS +++ b/board/freescale/ls1043aqds/MAINTAINERS @@ -1,6 +1,5 @@ LS1043AQDS BOARD M: Mingkai Hu <mingkai.hu(a)nxp.com> -M: Rajesh Bhagat <rajesh.bhagat(a)nxp.com> S: Maintained F: board/freescale/ls1043aqds/ F: include/configs/ls1043aqds.h diff --git a/board/freescale/ls1043ardb/MAINTAINERS b/board/freescale/ls1043ardb/MAINTAINERS index 36e7331538f..9bbec4d9acc 100644 --- a/board/freescale/ls1043ardb/MAINTAINERS +++ b/board/freescale/ls1043ardb/MAINTAINERS @@ -1,6 +1,5 @@ LS1043A BOARD M: Mingkai Hu <mingkai.hu(a)nxp.com> -M: Rajesh Bhagat <rajesh.bhagat(a)nxp.com> S: Maintained F: board/freescale/ls1043ardb/ F: board/freescale/ls1043ardb/ls1043ardb.c diff --git a/board/freescale/ls1046aqds/MAINTAINERS b/board/freescale/ls1046aqds/MAINTAINERS index 72c4253fcf5..e1db2aaa8e4 100644 --- a/board/freescale/ls1046aqds/MAINTAINERS +++ b/board/freescale/ls1046aqds/MAINTAINERS @@ -1,6 +1,5 @@ LS1046AQDS BOARD M: Mingkai Hu <Mingkai.Hu(a)nxp.com> -M: Rajesh Bhagat <rajesh.bhagat(a)nxp.com> S: Maintained F: board/freescale/ls1046aqds/ F: include/configs/ls1046aqds.h diff --git a/board/freescale/ls1046ardb/MAINTAINERS b/board/freescale/ls1046ardb/MAINTAINERS index 3c8cfe720dc..d5a6b261519 100644 --- a/board/freescale/ls1046ardb/MAINTAINERS +++ b/board/freescale/ls1046ardb/MAINTAINERS @@ -1,6 +1,5 @@ LS1046A BOARD M: Mingkai Hu <mingkai.hu(a)nxp.com> -M: Rajesh Bhagat <rajesh.bhagat(a)nxp.com> S: Maintained F: board/freescale/ls1046ardb/ F: board/freescale/ls1046ardb/ls1046ardb.c diff --git a/board/freescale/ls1088a/MAINTAINERS b/board/freescale/ls1088a/MAINTAINERS index 5c7925a95f4..95a14149e4f 100644 --- a/board/freescale/ls1088a/MAINTAINERS +++ b/board/freescale/ls1088a/MAINTAINERS @@ -1,6 +1,5 @@ LS1088ARDB BOARD M: Ashish Kumar <Ashish.Kumar(a)nxp.com> -M: Rajesh Bhagat <rajesh.bhagat(a)nxp.com> S: Maintained F: board/freescale/ls1088a/ F: include/configs/ls1088ardb.h @@ -11,7 +10,6 @@ F: configs/ls1088ardb_tfa_SECURE_BOOT_defconfig LS1088AQDS BOARD M: Ashish Kumar <Ashish.Kumar(a)nxp.com> -M: Rajesh Bhagat <rajesh.bhagat(a)nxp.com> S: Maintained F: board/freescale/ls1088a/ F: include/configs/ls1088aqds.h diff --git a/board/freescale/ls2080aqds/MAINTAINERS b/board/freescale/ls2080aqds/MAINTAINERS index 39d02ae3f46..fdad199ec25 100644 --- a/board/freescale/ls2080aqds/MAINTAINERS +++ b/board/freescale/ls2080aqds/MAINTAINERS @@ -1,6 +1,5 @@ LS2080A BOARD M: Priyanka Jain <priyanka.jain(a)nxp.com> -M: Rajesh Bhagat <rajesh.bhagat(a)nxp.com> M: Wasim Khan <wasim.khan(a)nxp.com> S: Maintained F: board/freescale/ls2080aqds/ diff --git a/board/freescale/ls2080ardb/MAINTAINERS b/board/freescale/ls2080ardb/MAINTAINERS index f49d26af3a0..f2f834ffbd9 100644 --- a/board/freescale/ls2080ardb/MAINTAINERS +++ b/board/freescale/ls2080ardb/MAINTAINERS @@ -10,7 +10,6 @@ F: configs/ls2080ardb_nand_defconfig LS2088A_QSPI-boot BOARD M: Priyanka Jain <priyanka.jain(a)nxp.com> -M: Rajesh Bhagat <rajesh.bhagat(a)nxp.com> M: Wasim Khan <wasim.khan(a)nxp.com> S: Maintained F: configs/ls2088ardb_qspi_defconfig -- 2.35.1.1320.gc452695387.dirty

2 5

How to debug u-boot data abort
by qianfan 22 Jul '23

22 Jul '23

Hi: I had a custom AM335X board connected my computer by usbnet. It always report data abort when 'dhcp': Next it the log: U-Boot 2022.01-rc1-00183-gfa5b4e2d19-dirty (Feb 25 2022 - 15:45:02 +0800) CPU : AM335X-GP rev 2.1 Model: WISDOM AM335X CCT DRAM: 512 MiB NAND: 256 MiB MMC: OMAP SD/MMC: 0 Loading Environment from NAND... *** Warning - bad CRC, using default environment Net: Could not get PHY for ethernet@4a100000: addr 0 eth2: ethernet@4a100000, eth3: usb_ether Hit any key to stop autoboot: 0 => setenv autoload no => dhcp using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in MAC de:ad:be:ef:00:01 HOST MAC de:ad:be:ef:00:00 RNDIS ready musb-hdrc: peripheral reset irq lost! high speed config #2: 2 mA, Ethernet Gadget, using RNDIS USB RNDIS network up! BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.200.4 (757 ms) data abort pc : [<9fe9b0a2>] lr : [<9febbc3f>] reloc pc : [<808130a2>] lr : [<80833c3f>] sp : 9de53410 ip : 9de53578 fp : 00000001 r10: 9de5345c r9 : 9de67e80 r8 : 9febbae5 r7 : 9de72c30 r6 : 9feec710 r5 : 0000000d r4 : 00000018 r3 : 3fdd8e04 r2 : 00000002 r1 : 9feec728 r0 : 9feec700 Flags: Nzcv IRQs off FIQs on Mode SVC_32 (T) Code: f023 0303 60ca 4403 (6091) 685a Resetting CPU ... resetting ... It's there has any doc about how to debug data abort? Or is the bug is already fixed? Thanks

7 22

[BUG] efi_loader: incorrect creation of device paths
by Heinrich Schuchardt 19 Jul '23

19 Jul '23

Hello Takahiro, in a prior mail we have discussed the creation of device paths for USB mass storage devices. On the sand boxyou get the following devices after 'usb start': Class Index Probed Driver Name ----------------------------------------------------------- usb 0 [ + ] usb_sandbox |-- usb@1 usb_hub 0 [ + ] usb_hub | `-- hub usb_mass_s 0 [ + ] usb_mass_storage | |-- usb_mass_storage blk 3 [ ] usb_storage_blk | | `-- usb_mass_storage.lun0 usb_mass_s 1 [ + ] usb_mass_storage | |-- usb_mass_storage blk 4 [ ] usb_storage_blk | | `-- usb_mass_storage.lun0 usb_mass_s 2 [ + ] usb_mass_storage | `-- usb_mass_storage blk 5 [ ] usb_storage_blk | `-- usb_mass_storage.lun0 For of these storage devices we try to create the same device path which is not allowable: => usb start starting USB... Bus usb@1: scanning bus usb@1 for devices... 5 USB Device(s) found scanning usb for storage devices... 3 Storage Device(s) found => => efidebug dh Scanning disk mmc2.blk... handle 0000000015e34f00, /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(2)/SD(0) Scanning disk mmc1.blk... handle 0000000015e36b30, /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(1) Scanning disk mmc0.blk... handle 0000000015e35b00, /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(2) Scanning disk usb_mass_storage.lun0... handle 0000000015e35c10, /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x1234,0x5678,0x9,0x0,0x0)/UsbClass(0x1234,0x5678,0x0,0x0,0x0) fs_devread read outside partition 2 Failed to mount ext2 filesystem... BTRFS: superblock end 69632 is larger than device size 512 Scanning disk usb_mass_storage.lun0... handle 0000000015e361f0, /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x1234,0x5678,0x9,0x0,0x0)/UsbClass(0x1234,0x5678,0x0,0x0,0x0) ERROR: failure to add disk device usb_mass_storage.lun0, r = 20 Error: Cannot initialize UEFI sub-system, r = 20 I will provide a patch that will allow the first USB device to be used and avoids stopping the boot process. But we really have to walk the dm tree to create a device patch for USB devices based on port IDs. We should add a new field to struct uclass_driver: struct efi_device_path *get_node(udevice *dev); This function shall return a pointer to an freshly allocated buffer with the device node for the device. To build the devicepath we can then walk the dm tree. To make migration easier: If the function pointer or the return value is NULL we can create a CTRL() node as dummy using the uclass_id and the device number. Best regards Heinrich

3 8

[PATCH] powerpc: Add support for CZ.NIC Turris 1.x routers
by Pali Rohár 10 Jul '23

10 Jul '23

CZ.NIC Turris 1.0 and 1.1 are open source routers, they have dual-core PowerPC Freescale P2020 CPU and are based on Freescale P2020RDB-PC-A board. Hardware design is fully open source, all firmware and hardware design files are available at Turris project website: https://docs.turris.cz/hw/turris-1x/turris-1x/ https://project.turris.cz/en/hardware.html This patch adds full U-Boot support for CZ.NIC Turris 1.x routers. P2020 BootROM can load U-Boot either from NOR flash or from SD card. So there is defconfig file turris_1x_nor_defconfig which builds NOR version and defconfig file turris_1x_sdcard_defconfig which builds SD card version. Design of CZ.NIC Turris 1.x routers is based on Freescale P2020RDB-PC-A board, so common board code from boards/freescale/p1_p2_rdb_pc directory is shared and linked also into Turris 1.x U-Boot board code. Turris 1.x code in this patch uses modern distroboot and can boot Linux kernel from various locations, including NAND, SD card, USB flash disks, NVMe disks or SATA disks (connected to extra SATA/SCSI PCIe controllers). Signed-off-by: Pali Rohár <pali(a)kernel.org> --- This patch depends on other powerpc patches: https://patchwork.ozlabs.org/bundle/pali/powerpc/ --- arch/powerpc/cpu/mpc85xx/Kconfig | 6 + arch/powerpc/dts/Makefile | 1 + arch/powerpc/dts/turris1x-u-boot.dtsi | 13 + arch/powerpc/dts/turris1x.dts | 475 ++++++++++++++++++++++++++ board/CZ.NIC/turris_1x/Kconfig | 177 ++++++++++ board/CZ.NIC/turris_1x/MAINTAINERS | 11 + board/CZ.NIC/turris_1x/Makefile | 15 + board/CZ.NIC/turris_1x/ddr.c | 27 ++ board/CZ.NIC/turris_1x/law.c | 13 + board/CZ.NIC/turris_1x/lbc.c | 26 ++ board/CZ.NIC/turris_1x/tlb.c | 142 ++++++++ board/CZ.NIC/turris_1x/turris_1x.c | 106 ++++++ configs/turris_1x_nor_defconfig | 50 +++ configs/turris_1x_sdcard_defconfig | 66 ++++ include/configs/turris_1x.h | 381 +++++++++++++++++++++ 15 files changed, 1509 insertions(+) create mode 100644 arch/powerpc/dts/turris1x-u-boot.dtsi create mode 100644 arch/powerpc/dts/turris1x.dts create mode 100644 board/CZ.NIC/turris_1x/Kconfig create mode 100644 board/CZ.NIC/turris_1x/MAINTAINERS create mode 100644 board/CZ.NIC/turris_1x/Makefile create mode 100644 board/CZ.NIC/turris_1x/ddr.c create mode 100644 board/CZ.NIC/turris_1x/law.c create mode 100644 board/CZ.NIC/turris_1x/lbc.c create mode 100644 board/CZ.NIC/turris_1x/tlb.c create mode 100644 board/CZ.NIC/turris_1x/turris_1x.c create mode 100644 configs/turris_1x_nor_defconfig create mode 100644 configs/turris_1x_sdcard_defconfig create mode 100644 include/configs/turris_1x.h diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig index 6f8b7593d250..28f69e7c73d2 100644 --- a/arch/powerpc/cpu/mpc85xx/Kconfig +++ b/arch/powerpc/cpu/mpc85xx/Kconfig @@ -150,6 +150,11 @@ config TARGET_P2020RDB imply CMD_SATA imply SATA_SIL +config TARGET_TURRIS_1X + bool "Support Turris 1.x" + select SUPPORT_SPL + select ARCH_P2020 + config TARGET_P2041RDB bool "Support P2041RDB" select ARCH_P2041 @@ -1201,6 +1206,7 @@ config SYS_FSL_LBC_CLK_DIV config FSL_VIA bool +source "board/CZ.NIC/turris_1x/Kconfig" source "board/emulation/qemu-ppce500/Kconfig" source "board/freescale/corenet_ds/Kconfig" source "board/freescale/mpc8548cds/Kconfig" diff --git a/arch/powerpc/dts/Makefile b/arch/powerpc/dts/Makefile index a4b0d7ddc4ff..d6462101211e 100644 --- a/arch/powerpc/dts/Makefile +++ b/arch/powerpc/dts/Makefile @@ -26,6 +26,7 @@ dtb-$(CONFIG_TARGET_T2080QDS) += t2080qds.dtb dtb-$(CONFIG_TARGET_T2080RDB) += t2080rdb.dtb dtb-$(CONFIG_TARGET_T4240RDB) += t4240rdb.dtb dtb-$(CONFIG_TARGET_TUGE1) += kmtuge1.dtb +dtb-$(CONFIG_TARGET_TURRIS_1X) += turris1x.dtb dtb-$(CONFIG_TARGET_TUXX1) += kmtuxa1.dtb dtb-$(CONFIG_TARGET_MCR3000) += mcr3000.dtb dtb-$(CONFIG_TARGET_GAZERBEAM) += gazerbeam.dtb diff --git a/arch/powerpc/dts/turris1x-u-boot.dtsi b/arch/powerpc/dts/turris1x-u-boot.dtsi new file mode 100644 index 000000000000..aa758818d564 --- /dev/null +++ b/arch/powerpc/dts/turris1x-u-boot.dtsi @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: GPL-2.0+ + +&soc { + i2c@3000 { + u-boot,dm-pre-reloc; + + crypto@64 { + u-boot,dm-pre-reloc; + }; + }; +}; + +#include "u-boot.dtsi" diff --git a/arch/powerpc/dts/turris1x.dts b/arch/powerpc/dts/turris1x.dts new file mode 100644 index 000000000000..1b27c1b0bba6 --- /dev/null +++ b/arch/powerpc/dts/turris1x.dts @@ -0,0 +1,475 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Turris 1.x Device Tree Source + * + * Copyright 2013 - 2022 CZ.NIC z.s.p.o. (http://www.nic.cz/) + * + * Pinout, Schematics and Altium hardware design files are open source + * and available at: https://docs.turris.cz/hw/turris-1x/turris-1x/ + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/leds/common.h> +/include/ "fsl/p2020si-pre.dtsi" + +/ { + model = "Turris 1.x"; + compatible = "cznic,turris1x", "fsl,P2020RDB-PC"; /* fsl,P2020RDB-PC is required for booting Linux */ + + aliases { + ethernet0 = &enet0; + ethernet1 = &enet1; + ethernet2 = &enet2; + serial0 = &serial0; + serial1 = &serial1; + pci0 = &pci0; + pci1 = &pci1; + pci2 = &pci2; + spi0 = &spi0; + }; + + memory { + device_type = "memory"; + }; + + soc: soc@ffe00000 { + ranges = <0x0 0x0 0xffe00000 0x00100000>; + + i2c@3000 { + /* PCA9557PW GPIO controller for boot config */ + gpio-controller@18 { + compatible = "nxp,pca9557"; + label = "bootcfg"; + reg = <0x18>; + #gpio-cells = <2>; + gpio-controller; + polarity = <0x00>; + }; + + /* STM32F030R8T6 MCU for power control */ + power-control@2a { + /* + * Turris Power Control firmware runs on STM32F0 MCU. + * This firmware is open source and available at: + * https://gitlab.nic.cz/turris/hw/turris_power_control + */ + reg = <0x2a>; + }; + + /* DDR3 SPD/EEPROM PSWP instruction */ + eeprom@32 { + reg = <0x32>; + }; + + /* SA56004ED temperature control */ + temperature-sensor@4c { + compatible = "nxp,sa56004"; + reg = <0x4c>; + interrupt-parent = <&gpio>; + interrupts = <12 IRQ_TYPE_LEVEL_LOW>, /* GPIO12 - ALERT pin */ + <13 IRQ_TYPE_LEVEL_LOW>; /* GPIO13 - CRIT pin */ + }; + + /* DDR3 SPD/EEPROM */ + eeprom@52 { + compatible = "atmel,spd"; + reg = <0x52>; + }; + + /* MCP79402-I/ST Protected EEPROM */ + eeprom@57 { + reg = <0x57>; + }; + + /* ATSHA204-TH-DA-T crypto module */ + crypto@64 { + compatible = "atmel,atsha204"; + reg = <0x64>; + }; + + /* IDT6V49205BNLGI clock generator */ + clock-generator@69 { + compatible = "idt,6v49205b"; + reg = <0x69>; + }; + + /* MCP79402-I/ST RTC */ + rtc@6f { + compatible = "microchip,mcp7940x"; + reg = <0x6f>; + interrupt-parent = <&gpio>; + interrupts = <14 0>; /* GPIO14 - MFP pin */ + }; + }; + + /* SPI on connector P1 */ + spi0: spi@7000 { + }; + + gpio: gpio-controller@fc00 { + #interrupt-cells = <2>; + interrupt-controller; + }; + + /* Connected to SMSC USB2412-DZK 2-Port USB 2.0 Hub Controller */ + usb@22000 { + phy_type = "ulpi"; + dr_mode = "host"; + }; + + enet0: ethernet@24000 { + /* Connected to port 6 of QCA8337N-AL3C switch */ + phy-connection-type = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + mdio@24520 { + /* QCA8337N-AL3C switch with integrated ethernet PHYs for LAN ports */ + switch@10 { + compatible = "qca,qca8337"; + interrupts = <2 1 0 0>; + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu1"; + ethernet = <&enet1>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan5"; + }; + + port@2 { + reg = <2>; + label = "lan4"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan2"; + }; + + port@5 { + reg = <5>; + label = "lan1"; + }; + + port@6 { + reg = <6>; + label = "cpu0"; + ethernet = <&enet0>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + + /* KSZ9031RNXCA ethernet phy for WAN port */ + phy: ethernet-phy@7 { + interrupts = <3 1 0 0>; + reg = <0x7>; + }; + }; + + ptp_clock@24e00 { + fsl,tclk-period = <5>; + fsl,tmr-prsc = <200>; + fsl,tmr-add = <0xcccccccd>; + fsl,tmr-fiper1 = <0x3b9ac9fb>; + fsl,tmr-fiper2 = <0x0001869b>; + fsl,max-adj = <249999999>; + }; + + enet1: ethernet@25000 { + /* Connected to port 0 of QCA8337N-AL3C switch */ + phy-connection-type = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + mdio@25520 { + status = "disabled"; + }; + + enet2: ethernet@26000 { + /* Connected to KSZ9031RNXCA ethernet phy (WAN port) */ + label = "wan"; + phy-handle = <&phy>; + phy-connection-type = "rgmii-id"; + }; + + mdio@26520 { + status = "disabled"; + }; + + sdhc@2e000 { + bus-width = <4>; + cd-gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + }; + + lbc: localbus@ffe05000 { + reg = <0 0xffe05000 0 0x1000>; + + ranges = <0x0 0x0 0x0 0xef000000 0x01000000>, /* NOR */ + <0x1 0x0 0x0 0xff800000 0x00040000>, /* NAND */ + <0x3 0x0 0x0 0xffa00000 0x00020000>; /* CPLD */ + + /* S29GL128P90TFIR10 NOR */ + nor@0,0 { + compatible = "cfi-flash"; + reg = <0x0 0x0 0x01000000>; + bank-width = <2>; + device-width = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + /* 128 kB for Device Tree Blob */ + reg = <0x00000000 0x00020000>; + label = "dtb"; + }; + + partition@20000 { + /* 1.7 MB for Rescue Linux Kernel Image */ + reg = <0x00020000 0x001a0000>; + label = "rescue-kernel"; + }; + + partition@1c0000 { + /* 1.5 MB for Rescue JFFS2 Root File System */ + reg = <0x001c0000 0x00180000>; + label = "rescue-rootfs"; + }; + + partition@340000 { + /* 11 MB for TAR.XZ Backup with content of NAND Root File System */ + reg = <0x00340000 0x00b00000>; + label = "backup-rootfs"; + }; + + partition@e40000 { + /* 768 kB for Certificates JFFS2 File System */ + reg = <0x00e40000 0x000c0000>; + label = "certificates"; + }; + + /* free unused space 0x00f00000-0x00f20000 */ + + partition@f20000 { + /* 128 kB for U-Boot Environment Variables */ + reg = <0x00f20000 0x00020000>; + label = "u-boot-env"; + }; + + partition@f40000 { + /* 768 kB for U-Boot Bootloader Image */ + reg = <0x00f40000 0x000c0000>; + label = "u-boot"; + }; + }; + }; + + /* MT29F2G08ABAEAWP:E NAND */ + nand@1,0 { + compatible = "fsl,p2020-fcm-nand", "fsl,elbc-fcm-nand"; + reg = <0x1 0x0 0x00040000>; + nand-ecc-mode = "soft"; + nand-ecc-algo = "bch"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + /* 256 MB for UBI with one volume: UBIFS Root File System */ + reg = <0x00000000 0x10000000>; + label = "rootfs"; + }; + }; + }; + + /* LCMXO1200C-3FTN256C FPGA */ + cpld@3,0 { + /* + * Turris CPLD firmware which runs on this Lattice FPGA, + * is extended version of P1021RDB-PC CPLD v4.1 firmware. + * It is backward compatible with its original version + * and the only extension is support for Turris LEDs. + * Turris CPLD firmware is open source and available at: + * https://gitlab.nic.cz/turris/hw/turris_cpld/-/blob/master/CZ_NIC_Router_CPL… + */ + compatible = "cznic,turris1x-cpld", "fsl,p1021rdb-pc-cpld", "simple-bus"; + reg = <0x3 0x0 0x30>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x3 0x0 0x00020000>; + + /* MAX6370KA+T watchdog */ + watchdog@2 { + /* + * CPLD firmware maps SET0, SET1 and SET2 + * input logic of MAX6370KA+T chip to CPLD + * memory space at byte offset 0x2. WDI + * input logic is outside of the CPLD and + * connected via external GPIO. + */ + compatible = "maxim,max6370"; + reg = <0x02 0x01>; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + + led-controller@13 { + /* + * LEDs are controlled by CPLD firmware. + * All five LAN LEDs share common RGB settings + * and so it is not possible to set different + * colors on different LAN ports. + */ + compatible = "cznic,turris1x-leds"; + reg = <0x13 0x1d>; + #address-cells = <1>; + #size-cells = <0>; + + multi-led@0 { + reg = <0x0>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_WAN; + }; + + multi-led@1 { + reg = <0x1>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_LAN; + function-enumerator = <5>; + }; + + multi-led@2 { + reg = <0x2>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_LAN; + function-enumerator = <4>; + }; + + multi-led@3 { + reg = <0x3>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_LAN; + function-enumerator = <3>; + }; + + multi-led@4 { + reg = <0x4>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + }; + + multi-led@5 { + reg = <0x5>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + }; + + multi-led@6 { + reg = <0x6>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_WLAN; + }; + + multi-led@7 { + reg = <0x7>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_POWER; + }; + }; + }; + }; + + pci2: pcie@ffe08000 { + /* + * PCIe bus for on-board TUSB7340RKM USB 3.0 xHCI controller. + * This xHCI controller is available only on Turris 1.1 boards. + * Turris 1.0 boards have nothing connected to this PCIe bus, + * so system would see only PCIe Root Port of this PCIe Root + * Complex. TUSB7340RKM xHCI controller has four SuperSpeed + * channels. Channel 0 is connected to the front USB 3.0 port, + * channel 1 (but only USB 2.0 subset) to USB 2.0 pins on mPCIe + * slot 1 (CN5), channels 2 and 3 to connector P600. + * + * P2020 PCIe Root Port uses 1MB of PCIe MEM and xHCI controller + * uses 64kB + 8kB of PCIe MEM. No PCIe IO is used or required. + * So allocate 2MB of PCIe MEM for this PCIe bus. + */ + reg = <0 0xffe08000 0 0x1000>; + ranges = <0x02000000 0x0 0xc0000000 0 0xc0000000 0x0 0x00200000>, /* MEM */ + <0x01000000 0x0 0x00000000 0 0xffc20000 0x0 0x00010000>; /* IO */ + + pcie@0 { + ranges; + }; + }; + + pci1: pcie@ffe09000 { + /* PCIe bus on mPCIe slot 2 (CN6) for expansion mPCIe card */ + reg = <0 0xffe09000 0 0x1000>; + ranges = <0x02000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000>, /* MEM */ + <0x01000000 0x0 0x00000000 0 0xffc10000 0x0 0x00010000>; /* IO */ + + pcie@0 { + ranges; + }; + }; + + pci0: pcie@ffe0a000 { + /* + * PCIe bus on mPCIe slot 1 (CN5) for expansion mPCIe card. + * Turris 1.1 boards have in this mPCIe slot additional USB 2.0 + * pins via channel 1 of TUSB7340RKM xHCI controller and also + * additional SIM card slot, both for USB-based WWAN cards. + */ + reg = <0 0xffe0a000 0 0x1000>; + ranges = <0x02000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000>, /* MEM */ + <0x01000000 0x0 0x00000000 0 0xffc00000 0x0 0x00010000>; /* IO */ + + pcie@0 { + ranges; + }; + }; +}; + +/include/ "fsl/p2020si-post.dtsi" diff --git a/board/CZ.NIC/turris_1x/Kconfig b/board/CZ.NIC/turris_1x/Kconfig new file mode 100644 index 000000000000..103c00d585d7 --- /dev/null +++ b/board/CZ.NIC/turris_1x/Kconfig @@ -0,0 +1,177 @@ +# SPDX-License-Identifier: GPL-2.0+ +# (C) 2022 Pali Rohár <pali(a)kernel.org> + +if TARGET_TURRIS_1X + +# Board identification +config SYS_BOARD + default "turris_1x" +config SYS_VENDOR + default "CZ.NIC" +config SYS_CONFIG_NAME + default "turris_1x" +config DEFAULT_DEVICE_TREE + default "turris1x" + +# Board functions +config ATSHA204A + default y +config BOARD_EARLY_INIT_F + default y +config BOARD_EARLY_INIT_R + default y +config LAST_STAGE_INIT + default y +config OF_BOARD_SETUP + default y +config MISC + default y + +# ENV +config ENV_SIZE + default 0x2000 +config ENV_SECT_SIZE + default 0x20000 +config ENV_OVERWRITE + default y +config ENV_IS_IN_FLASH + default y +config ENV_ADDR + default 0xeff20000 # in NOR +config SYS_RELOC_GD_ENV_ADDR + default y + +# DDR +config DDR_CLK_FREQ + default 66666666 + +# UART +config DEBUG_UART_BASE + default 0xffe04500 if DEBUG_UART +config DEBUG_UART_CLOCK + default 37500000 if DEBUG_UART +config SYS_NS16550 + default y + +# I2C +config I2C_SET_DEFAULT_BUS_NUM + default y +config SYS_FSL_I2C_OFFSET + default 0x3000 +config SYS_FSL_HAS_I2C2_OFFSET + default y +config SYS_FSL_I2C2_OFFSET + default 0x3100 +config SYS_I2C_FSL + default y + +# PCIe +config PCI_INIT_R + default y +config PCIE_FSL + default y + +# Ethernet +config MII + default y +config PHY_FIXED + default y +config TSEC_ENET + default y + +# USB +config USB_EHCI_FSL + default y +config USB_XHCI_HCD + default y +config USB_XHCI_PCI + default y + +# SDHC +config FSL_ESDHC + default y +config FSL_PREPBL_ESDHC_BOOT_SECTOR + default y if SYS_EXTRA_OPTIONS = SDCARD +config SYS_FSL_ESDHC_DEFAULT_BUS_WIDTH + default 4 + +# NOR (CS0) +config SYS_BR0_PRELIM_BOOL + default y +config SYS_BR0_PRELIM + default 0xef001001 # (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_MS_GPCM | BR_V) +config SYS_OR0_PRELIM + default 0xff000ff7 # (OR_AM_16MB | OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS | OR_GPCM_SCY_15 | OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) +config MTD_NOR_FLASH + default y +config CFI_FLASH + default y +config FLASH_CFI_MTD + default y +config SYS_FLASH_USE_BUFFER_WRITE + default y + +# NAND (CS1) +config SYS_BR1_PRELIM_BOOL + default y +config SYS_BR1_PRELIM + default 0xff800821 # (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) | BR_PS_8 | BR_MS_FCM | BR_V) +config SYS_OR1_PRELIM + default 0xfffc0796 # (OR_AM_256KB | OR_FCM_PGS | OR_FCM_CSCT | OR_FCM_CST | OR_FCM_CHT | OR_FCM_SCY_1 | OR_FCM_TRLX | OR_FCM_EHTR) +config MTD_RAW_NAND + default y +config NAND_FSL_ELBC + default y +config NAND_FSL_ELBC_DT + default y +config BCH + default y +config SYS_FLASH_CFI + default y + +# CPLD (CS3) +config SYS_BR3_PRELIM_BOOL + default y +config SYS_BR3_PRELIM + default 0xffa00801 # (BR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) | BR_PS_8 | BR_MS_GPCM | BR_V) +config SYS_OR3_PRELIM + default 0xfffe09f7 # (OR_AM_128KB | OR_GPCM_CSNT | OR_GPCM_XACS | OR_GPCM_SCY_15 | OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) + +config MPC85XX_HAVE_RESET_VECTOR + default y if SYS_EXTRA_OPTIONS != SDCARD + +config SYS_TEXT_BASE + default 0x11000000 if SPL # in DDR + default 0xf8f80000 if SYS_EXTRA_OPTIONS = SDCARD # in SRAM + default 0xeff40000 # in NOR + +if SPL + +config SPL_TEXT_BASE + default 0xf8f80000 if SYS_EXTRA_OPTIONS = SDCARD # in SRAM + default 0xeff40000 # in NOR + +config SPL_ENV_SUPPORT + default y +config SPL_FRAMEWORK + default n +config SPL_I2C + default y +config SPL_LIBCOMMON_SUPPORT + default y +config SPL_LIBGENERIC_SUPPORT + default y +config SPL_MMC + default y if SYS_EXTRA_OPTIONS = SDCARD +config SPL_MMC_BOOT + default y if SYS_EXTRA_OPTIONS = SDCARD +config SPL_MPC8XXX_INIT_DDR + default y +config SPL_SERIAL + default y +config SPL_SYS_I2C_LEGACY + default y + +endif + +endif diff --git a/board/CZ.NIC/turris_1x/MAINTAINERS b/board/CZ.NIC/turris_1x/MAINTAINERS new file mode 100644 index 000000000000..04f4915f7d7d --- /dev/null +++ b/board/CZ.NIC/turris_1x/MAINTAINERS @@ -0,0 +1,11 @@ +TURRIS 1.X BOARD +M: Pali Rohár <pali(a)kernel.org> +S: Maintained +F: arch/powerpc/dts/turris1x-u-boot.dtsi +F: arch/powerpc/dts/turris1x.dts +F: board/CZ.NIC/turris_1x/ +F: board/CZ.NIC/turris_atsha_otp.c +F: board/CZ.NIC/turris_atsha_otp.h +F: configs/turris_1x_nor_defconfig +F: configs/turris_1x_sdcard_defconfig +F: include/configs/turris_1x.h diff --git a/board/CZ.NIC/turris_1x/Makefile b/board/CZ.NIC/turris_1x/Makefile new file mode 100644 index 000000000000..d935456d27c9 --- /dev/null +++ b/board/CZ.NIC/turris_1x/Makefile @@ -0,0 +1,15 @@ +# SPDX-License-Identifier: GPL-2.0+ +# (C) 2022 Pali Rohár <pali(a)kernel.org> + +ifdef CONFIG_SPL_BUILD +obj-y += ../../freescale/p1_p2_rdb_pc/spl.o +endif + +obj-y += ../../freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.o +obj-y += ../turris_atsha_otp.o + +obj-y += turris_1x.o +obj-y += ddr.o +obj-y += law.o +obj-y += lbc.o +obj-y += tlb.o diff --git a/board/CZ.NIC/turris_1x/ddr.c b/board/CZ.NIC/turris_1x/ddr.c new file mode 100644 index 000000000000..ced4e97bfa30 --- /dev/null +++ b/board/CZ.NIC/turris_1x/ddr.c @@ -0,0 +1,27 @@ +// SPDX-License-Identifier: GPL-2.0+ +// (C) 2022 Pali Rohár <pali(a)kernel.org> + +#include <common.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> + +void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm, unsigned int ctrl_num) +{ + int i; + + popts->clk_adjust = 6; + popts->cpo_override = 0x1f; + popts->write_data_delay = 2; + popts->half_strength_driver_enable = 1; + popts->wrlvl_en = 1; + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + popts->wrlvl_start = 0x8; + popts->trwt_override = 1; + popts->trwt = 0; + + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER; + popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS; + } +} diff --git a/board/CZ.NIC/turris_1x/law.c b/board/CZ.NIC/turris_1x/law.c new file mode 100644 index 000000000000..1502ceecf823 --- /dev/null +++ b/board/CZ.NIC/turris_1x/law.c @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: GPL-2.0+ +// (C) 2022 Pali Rohár <pali(a)kernel.org> + +#include <common.h> +#include <asm/fsl_law.h> + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_256K, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_LBC), +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/CZ.NIC/turris_1x/lbc.c b/board/CZ.NIC/turris_1x/lbc.c new file mode 100644 index 000000000000..de2f5d25da6d --- /dev/null +++ b/board/CZ.NIC/turris_1x/lbc.c @@ -0,0 +1,26 @@ +// SPDX-License-Identifier: GPL-2.0+ +// (C) 2022 Pali Rohár <pali(a)kernel.org> + +#include <common.h> +#include <asm/fsl_lbc.h> +#include <linux/build_bug.h> + +/* + * Check if preliminary base/options config options have correct values. + * Due to broken build system, it is not possible to define these options + * in config.h file nor in other sane place. So do compile time checks here. + */ + +#define LBC_BR_NOR (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_MS_GPCM | BR_V) +#define LBC_OR_NOR (OR_AM_16MB | OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS | OR_GPCM_SCY_15 | OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) +#define LBC_BR_NAND (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) | BR_PS_8 | BR_MS_FCM | BR_V) +#define LBC_OR_NAND (OR_AM_256KB | OR_FCM_PGS | OR_FCM_CSCT | OR_FCM_CST | OR_FCM_CHT | OR_FCM_SCY_1 | OR_FCM_TRLX | OR_FCM_EHTR) +#define LBC_BR_CPLD (BR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) | BR_PS_8 | BR_MS_GPCM | BR_V) +#define LBC_OR_CPLD (OR_AM_128KB | OR_GPCM_CSNT | OR_GPCM_XACS | OR_GPCM_SCY_15 | OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) + +static_assert(CONFIG_SYS_BR0_PRELIM == LBC_BR_NOR); +static_assert(CONFIG_SYS_OR0_PRELIM == LBC_OR_NOR); +static_assert(CONFIG_SYS_BR1_PRELIM == LBC_BR_NAND); +static_assert(CONFIG_SYS_BR1_PRELIM == LBC_BR_NAND); +static_assert(CONFIG_SYS_BR3_PRELIM == LBC_BR_CPLD); +static_assert(CONFIG_SYS_BR3_PRELIM == LBC_BR_CPLD); diff --git a/board/CZ.NIC/turris_1x/tlb.c b/board/CZ.NIC/turris_1x/tlb.c new file mode 100644 index 000000000000..e7113b0cd4c8 --- /dev/null +++ b/board/CZ.NIC/turris_1x/tlb.c @@ -0,0 +1,142 @@ +// SPDX-License-Identifier: GPL-2.0+ +// (C) 2022 Pali Rohár <pali(a)kernel.org> + +#include <common.h> +#include <asm/mmu.h> +#include <linux/sizes.h> +#include <linux/build_bug.h> + +/* + * NOTE: e500v2 supports only following Book-E page sizes: + * + * TLB0: + * BOOKE_PAGESZ_4K + * + * TLB1: + * BOOKE_PAGESZ_4K + * BOOKE_PAGESZ_16K + * BOOKE_PAGESZ_64K + * BOOKE_PAGESZ_256K + * BOOKE_PAGESZ_1M + * BOOKE_PAGESZ_4M + * BOOKE_PAGESZ_16M + * BOOKE_PAGESZ_64M + * BOOKE_PAGESZ_256M + * BOOKE_PAGESZ_1G + * BOOKE_PAGESZ_4G + */ + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 */ + + /* ***** - Initial stack in L1 cache 16K */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 0 * SZ_4K, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 0 * SZ_4K, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 1 * SZ_4K , + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 1 * SZ_4K, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 2 * SZ_4K , + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 2 * SZ_4K, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 3 * SZ_4K , + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 3 * SZ_4K, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + + /* *I*** - Boot page 4K */ + SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR, + 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I, + 0, 0, BOOKE_PAGESZ_4K, 1), + + /* *I*G* - CCSR 1M */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, + CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* W**G* - NOR 16M */ + /* This will be changed to *I*G* after relocation to RAM in board_early_init_r() */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, + CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_16M, 1), + + /* *I*G* - CPLD 256K (effective 128K) */ + SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, + CONFIG_SYS_CPLD_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_256K, 1), + + /* *I*G* - NAND 1M */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, + CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256K, 1), + + /* *I*G* - PCIe MEM (bus 1 and 2) 1G */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, + CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCIe MEM (bus 3) 4M (effective 2M) */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, + CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_4M, 1), + + /* *I*G* - PCIe I/O (all 3 buses) 256K (effective 192K) */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, + CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_256K, 1), + +#ifdef CONFIG_SYS_INIT_L2_ADDR + /* ***G* - Initial SRAM in L2 cache 512K */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, + CONFIG_SYS_INIT_L2_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, + 0, 8, BOOKE_PAGESZ_256K, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + SZ_256K, + CONFIG_SYS_INIT_L2_ADDR_PHYS + SZ_256K, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, + 0, 9, BOOKE_PAGESZ_256K, 1), +#endif + +#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD) + /* **M** - SDRAM 2G */ + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, + CONFIG_SYS_DDR_SDRAM_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, + 0, 10, BOOKE_PAGESZ_1G, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + SZ_1G, + CONFIG_SYS_DDR_SDRAM_BASE + SZ_1G, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, + 0, 11, BOOKE_PAGESZ_1G, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); + +/* + * PCIe MEM TLB entry expects that second PCIe MEM window is mapped after the + * first PCIe MEM window. Check for this requirement. + */ +static_assert(CONFIG_SYS_PCIE2_MEM_VIRT == CONFIG_SYS_PCIE1_MEM_VIRT + SZ_512M); +static_assert(CONFIG_SYS_PCIE2_MEM_PHYS == CONFIG_SYS_PCIE1_MEM_PHYS + SZ_512M); + +/* + * PCIe I/O TLB entry expects that all 3 PCIe I/O windows are mapped one after + * another. Check for this requirement. + */ +static_assert(CONFIG_SYS_PCIE2_IO_VIRT == CONFIG_SYS_PCIE1_IO_VIRT + SZ_64K); +static_assert(CONFIG_SYS_PCIE2_IO_PHYS == CONFIG_SYS_PCIE1_IO_PHYS + SZ_64K); +static_assert(CONFIG_SYS_PCIE3_IO_VIRT == CONFIG_SYS_PCIE2_IO_VIRT + SZ_64K); +static_assert(CONFIG_SYS_PCIE3_IO_PHYS == CONFIG_SYS_PCIE2_IO_PHYS + SZ_64K); diff --git a/board/CZ.NIC/turris_1x/turris_1x.c b/board/CZ.NIC/turris_1x/turris_1x.c new file mode 100644 index 000000000000..8f2400f79e05 --- /dev/null +++ b/board/CZ.NIC/turris_1x/turris_1x.c @@ -0,0 +1,106 @@ +// SPDX-License-Identifier: GPL-2.0+ +// (C) 2022 Pali Rohár <pali(a)kernel.org> + +#include <common.h> +#include <init.h> +#include <env.h> + +#include "../turris_atsha_otp.h" + +/* + * Reset time cycle register provided by Turris CPLD firmware. + * Turris CPLD firmware is open source and available at: + * https://gitlab.nic.cz/turris/hw/turris_cpld/-/blob/master/CZ_NIC_Router_CPL… + */ +#define TURRIS_CPLD_RESET_TIME_CYCLE_REG ((void *)CONFIG_SYS_CPLD_BASE + 0x1f) +#define TURRIS_CPLD_RESET_TIME_CYCLE_300MS BIT(0) +#define TURRIS_CPLD_RESET_TIME_CYCLE_1S BIT(1) +#define TURRIS_CPLD_RESET_TIME_CYCLE_2S BIT(2) +#define TURRIS_CPLD_RESET_TIME_CYCLE_3S BIT(3) +#define TURRIS_CPLD_RESET_TIME_CYCLE_4S BIT(4) +#define TURRIS_CPLD_RESET_TIME_CYCLE_5S BIT(5) +#define TURRIS_CPLD_RESET_TIME_CYCLE_6S BIT(6) + +int misc_init_r(void) +{ + turris_atsha_otp_init_mac_addresses(0); + return 0; +} + +int show_board_info(void) +{ + u32 version_num, serial_num; + int err; + + err = turris_atsha_otp_get_serial_number(&version_num, &serial_num); + + /* + * Turris 1.0 boards have version_num 0x5. + * Turris 1.1 boards have version_num 0x6, 0x7, 0x8 and 0x9. + */ + printf("Model: Turris 1.%c\n", err ? 'x' : + (be32_to_cpu(version_num) >= 0x6) ? '1' : '0'); + + if (err) + printf("Serial Number: unknown\n"); + else + printf("Serial Number: %08X%08X\n", be32_to_cpu(version_num), + be32_to_cpu(serial_num)); + + err = checkboard(); + if (err) + return err; + + return 0; +} + +static void handle_reset_button(void) +{ + const char * const vars[1] = { "bootcmd_rescue", }; + + /* + * Ensure that bootcmd_rescue has always stock value, so that running + * run bootcmd_rescue + * always works correctly. + */ + env_set_default_vars(1, (char * const *)vars, 0); + + /* Check if red reset button was hold for at least six seconds. */ + if (in_8(TURRIS_CPLD_RESET_TIME_CYCLE_REG) & TURRIS_CPLD_RESET_TIME_CYCLE_6S) { + const char * const vars[2] = { + "bootcmd", + "distro_bootcmd", + }; + + /* + * Set the above envs to their default values, in case the user + * managed to break them. + */ + env_set_default_vars(2, (char * const *)vars, 0); + + /* Ensure bootcmd_rescue is used by distroboot */ + env_set("boot_targets", "rescue"); + + printf("RESET button was pressed, overwriting boot_targets!\n"); + } else { + /* + * In case the user somehow managed to save environment with + * boot_targets=rescue, reset boot_targets to default value. + * This could happen in subsequent commands if bootcmd_rescue + * failed. + */ + if (!strcmp(env_get("boot_targets"), "rescue")) { + const char * const vars[1] = { + "boot_targets", + }; + + env_set_default_vars(1, (char * const *)vars, 0); + } + } +} + +int last_stage_init(void) +{ + handle_reset_button(); + return 0; +} diff --git a/configs/turris_1x_nor_defconfig b/configs/turris_1x_nor_defconfig new file mode 100644 index 000000000000..ada6789dd6cd --- /dev/null +++ b/configs/turris_1x_nor_defconfig @@ -0,0 +1,50 @@ +CONFIG_PPC=y +CONFIG_MPC85xx=y +# CONFIG_CMD_ERRATA is not set +CONFIG_TARGET_TURRIS_1X=y +CONFIG_AHCI=y +CONFIG_ENV_VARS_UBOOT_CONFIG=y +CONFIG_MP=y +CONFIG_FIT=y +CONFIG_SUPPORT_RAW_INITRD=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_BOOTDELAY=3 +CONFIG_USE_BOOTCOMMAND=y +CONFIG_BOOTCOMMAND="run distro_bootcmd" +CONFIG_USE_PREBOOT=y +CONFIG_HUSH_PARSER=y +# CONFIG_AUTO_COMPLETE is not set +CONFIG_CMD_BOOTZ=y +# CONFIG_CMD_EEPROM is not set +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_LSBLK=y +CONFIG_CMD_MMC=y +CONFIG_CMD_MTD=y +CONFIG_CMD_PART=y +CONFIG_CMD_PCI=y +CONFIG_CMD_USB=y +CONFIG_CMD_DHCP=y +# CONFIG_CMD_NFS is not set +CONFIG_CMD_PING=y +# CONFIG_CMD_HASH is not set +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_CMD_FS_UUID=y +CONFIG_CMD_UBI=y +CONFIG_OF_CONTROL=y +CONFIG_DM=y +CONFIG_SCSI_AHCI=y +CONFIG_AHCI_PCI=y +CONFIG_DM_I2C=y +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_DM_ETH=y +CONFIG_DM_MDIO=y +CONFIG_NVME_PCI=y +CONFIG_SCSI=y +CONFIG_DM_SCSI=y +CONFIG_USB=y +CONFIG_USB_STORAGE=y diff --git a/configs/turris_1x_sdcard_defconfig b/configs/turris_1x_sdcard_defconfig new file mode 100644 index 000000000000..fcceb12cbcd1 --- /dev/null +++ b/configs/turris_1x_sdcard_defconfig @@ -0,0 +1,66 @@ +CONFIG_PPC=y +CONFIG_SPL=y +CONFIG_MPC85xx=y +CONFIG_TARGET_TURRIS_1X=y +CONFIG_DEBUG_UART=y +CONFIG_AHCI=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_MP=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_SYS_EXTRA_OPTIONS="SDCARD" +CONFIG_BOOTDELAY=3 +CONFIG_USE_PREBOOT=y +CONFIG_CMD_BOOTZ=y +CONFIG_CMD_IMLS=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_SHA1SUM=y +CONFIG_CMD_LZMADEC=y +CONFIG_CMD_UNLZ4=y +CONFIG_CMD_UNZIP=y +CONFIG_CMD_DM=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_LSBLK=y +CONFIG_CMD_MMC=y +CONFIG_CMD_MTD=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +CONFIG_CMD_WDT=y +CONFIG_CMD_TFTPPUT=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIME=y +CONFIG_CMD_BTRFS=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_SQUASHFS=y +CONFIG_CMD_FS_UUID=y +CONFIG_CMD_UBI=y +CONFIG_OF_CONTROL=y +CONFIG_NETCONSOLE=y +CONFIG_DM=y +CONFIG_SCSI_AHCI=y +CONFIG_AHCI_PCI=y +CONFIG_DM_PCA953X=y +CONFIG_MPC8XXX_GPIO=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_EEPROM_ADDR=0x52 +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_DM_ETH=y +CONFIG_DM_MDIO=y +CONFIG_NVME_PCI=y +CONFIG_DM_RTC=y +CONFIG_RTC_DS1307=y +CONFIG_SCSI=y +CONFIG_DM_SCSI=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_FSL_ESPI=y +CONFIG_USB=y +# CONFIG_WATCHDOG_AUTOSTART is not set +CONFIG_WDT=y +CONFIG_WDT_MAX6370=y +CONFIG_FAT_WRITE=y diff --git a/include/configs/turris_1x.h b/include/configs/turris_1x.h new file mode 100644 index 000000000000..576767a6cbec --- /dev/null +++ b/include/configs/turris_1x.h @@ -0,0 +1,381 @@ +// SPDX-License-Identifier: GPL-2.0+ +// (C) 2022 Pali Rohár <pali(a)kernel.org> + +#ifndef _CONFIG_TURRIS_1X_H +#define _CONFIG_TURRIS_1X_H + +#include <linux/sizes.h> + +/* + * Turris 1.x memory map: + * + * 0x0000_0000 - 0x7fff_ffff 2 GB DDR cacheable + * 0x8000_0000 - 0xbfff_ffff 1 GB PCIe MEM (bus 1-2) non-cacheable + * 0xc000_0000 - 0xc01f_ffff 2 MB PCIe MEM (bus 3) non-cacheable + * 0xc020_0000 - 0xeeff_ffff 750 MB unused + * 0xef00_0000 - 0xefff_ffff 16 MB NOR (CS0) non-cacheable + * 0xf000_0000 - 0xf8f7_ffff 143 MB unused + * 0xf8f8_0000 - 0xf8ff_ffff 512 kB L2 SRAM cacheable (early boot, SD card only) + * 0xf900_0000 - 0xff6f_ffff 103 MB unused + * 0xff70_0000 - 0xff7f_ffff 1 MB CCSR non-cacheable (SPL only) + * 0xff80_0000 - 0xff80_7fff 32 kB NAND (CS1) non-cacheable + * 0xffa0_0000 - 0xffa1_ffff 128 kB CPLD (CS3) non-cacheable + * 0xffc0_0000 - 0xffc2_ffff 192 kB PCIe IO non-cacheable + * 0xffd0_0000 - 0xffd0_3fff 16 kB L1 stack cacheable (early boot) + * 0xffe0_0000 - 0xffef_ffff 1 MB CCSR non-cacheable (not in SPL) + * 0xffff_f000 - 0xffff_ffff 4 kB Boot page non-cacheable + */ + +/* + * Global settings + */ + +/* + * CONFIG_ENABLE_36BIT_PHYS needs to be always defined when processor supports + * 36-bit addressing (which is case for P2020), also when only 32-bit addressing + * mode is used. Name of this config option is misleading and should have been + * called SUPPORT instead of ENABLE. + * When CONFIG_PHYS_64BIT is set then 36-bit addressing is used, when unset then + * 32-bit addressing is used. Name of this config option is misleading too and + * should have been called 36BIT and ENABLED, not 64BIT. + * Due to performance reasons (see document AN4064), Turris 1.x boards use only + * 32-bit addressing. Also all config options are currently defined only for + * 32-bit addressing, so compiling U-Boot for 36-bit addressing is not possible + * yet. + */ +#define CONFIG_ENABLE_36BIT_PHYS +#ifdef CONFIG_PHYS_64BIT +#error "36-bit addressing is not implemented for this board" +#endif + +#define CONFIG_HWCONFIG +#define CONFIG_L2_CACHE +#define CONFIG_SYS_L2_SIZE SZ_512K +#define CONFIG_BTB /* Enable Branch Prediction */ + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE +#else +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#endif + +#define CONFIG_SYS_MONITOR_LEN CONFIG_BOARD_SIZE_LIMIT + +/* + * Boot settings + */ + +#ifdef CONFIG_SDCARD + +/* + * Booting from SD card + * BootROM configures L2 cache as SRAM, loads image from SD card into L2 SRAM + * and starts executing directly _start entry point in L2 SRAM. Therefore reset + * vector is not used and maximal size of the image is L2 cache size. For builds + * with SPL there is no limit of U-Boot proper as BootROM loads SPL which then + * loads U-Boot proper directly into DDR. + */ + +#define CONFIG_SYS_MPC85XX_NO_RESETVEC + +/* For SD card builds without SPL it is needed to set CONFIG_SYS_RAMBOOT */ +#ifndef CONFIG_SPL +#define CONFIG_SYS_RAMBOOT +#endif + +#ifdef CONFIG_SPL +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SPL_PAD_TO 0 +#endif + +#ifdef CONFIG_SPL_BUILD +#ifdef CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR +#define CONFIG_SPL_MAX_SIZE (CONFIG_SYS_L2_SIZE + CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA * SZ_512) +#else +#define CONFIG_SPL_MAX_SIZE CONFIG_SYS_L2_SIZE +#endif +#define CONFIG_SYS_MMC_U_BOOT_SIZE CONFIG_BOARD_SIZE_LIMIT +#define CONFIG_SYS_MMC_U_BOOT_DST CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MMC_U_BOOT_START CONFIG_SYS_TEXT_BASE +#endif + +#else + +/* + * Booting from NOR + * Last 4kB page of the NOR is mapped into CPU address space and CPU starts + * executing last instruction of that page, which is reset vector address. + * We have 16 MB large NOR memory, so define correct reset vector address. + */ + +#define CONFIG_RESET_VECTOR_ADDRESS (CONFIG_SYS_FLASH_BASE + SZ_16M - 4) + +#endif + +/* + * CONFIG_BOARD_SIZE_LIMIT must be hex number because it is used in Makefile. + * For NOR build, size of the U-Boot binary must always be 768 kB. + * For SD card build with SPL, there is no limit, just broken build system which + * cannot fill CONFIG_SYS_MMC_U_BOOT_SIZE and CONFIG_SYS_MONITOR_LEN values + * automatically. So choose it as lowest value as possible with which build + * process does not fail, to minimize final binary size. + * For SD card build without SPL, there is upper limit of L2 cache size. + */ +#ifndef CONFIG_SDCARD +#define CONFIG_BOARD_SIZE_LIMIT 0x000c0000 /* 768 kB */ +#elif defined(CONFIG_SPL) +#define CONFIG_BOARD_SIZE_LIMIT 0x00100000 /* 1 MB */ +#else +#define CONFIG_BOARD_SIZE_LIMIT 0x00080000 /* 512 kB - must be same as CONFIG_SYS_L2_SIZE */ +#endif + +/* + * Initial stack in L1 cache + */ + +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS +#define CONFIG_SYS_INIT_RAM_SIZE SZ_16K +#define CONFIG_SYS_INIT_RAM_LOCK + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* + * Initial SRAM in L2 cache + */ + +/* Initial SRAM is used only for SD card boot in first stage image */ +#ifdef CONFIG_SDCARD +#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD) +#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SPL_RELOC_TEXT_BASE CONFIG_SYS_MONITOR_BASE +#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 112 * SZ_1K) +#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 116 * SZ_1K) +#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 148 * SZ_1K) +#define CONFIG_SPL_RELOC_MALLOC_SIZE (364 * SZ_1K) +#endif +#endif + +/* + * CCSR + */ + +#define CONFIG_SYS_CCSRBAR 0xffe00000 +#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR + +/* + * U-Boot _start code expects that if CCSRBAR is configured to its default + * location and automatically relocate it to the new CONFIG_SYS_CCSRBAR_PHYS + * location. Relocation to the new location can be skipped by defining macro + * CONFIG_SYS_CCSR_DO_NOT_RELOCATE. + * + * All addresses in device tree are set to according the new relocated CCSRBAR. + * So device tree code cannot be used when CONFIG_SYS_CCSR_DO_NOT_RELOCATE is + * set. + * + * If CCSRBAR is is not configured to its default location then _start code + * hangs or crashes. + * + * So relocation of CCSRBAR must be disabled in every code which runs before + * U-Boot proper (e.g. SPL), otherwise U-Boot proper's _start code crashes. + */ +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE +#endif + +/* + * DDR + */ + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 + +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define CONFIG_SYS_I2C_PCA9557_ADDR 0x18 +#define SPD_EEPROM_ADDRESS 0x52 + +/* + * NOR + */ + +#define CONFIG_SYS_FLASH_BASE 0xef000000 +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE + +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* 16 MB */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_QUIET_TEST + +/* + * NAND + */ + +#define CONFIG_SYS_NAND_BASE 0xff800000 +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE + +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM +#define CONFIG_NAND_ECC_BCH + +/* + * CPLD + */ + +#define CONFIG_SYS_CPLD_BASE 0xffa00000 +#define CONFIG_SYS_CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE + +/* + * Serial Port + */ + +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) + +#define CONFIG_SYS_BAUDRATE_TABLE { 600, 1200, 1800, 2400, 4800, 9600, \ + 19200, 38400, 57600, 115200, 230400, \ + 460800, 500000, 576000, 921600, \ + 1000000, 1500000, 2000000, 3000000 } + +/* + * PCIe + */ + +/* PCIe bus on mPCIe slot 1 (CN5) for expansion mPCIe card */ +#define CONFIG_PCIE1 +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_VIRT +#define CONFIG_SYS_PCIE1_IO_PHYS CONFIG_SYS_PCIE1_IO_VIRT + +/* PCIe bus on mPCIe slot 2 (CN6) for expansion mPCIe card */ +#define CONFIG_PCIE2 +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 +#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_VIRT +#define CONFIG_SYS_PCIE2_IO_PHYS CONFIG_SYS_PCIE2_IO_VIRT + +/* PCIe bus for on-board TUSB7340RKM USB 3.0 xHCI controller */ +#define CONFIG_PCIE3 +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc20000 +#define CONFIG_SYS_PCIE3_MEM_PHYS CONFIG_SYS_PCIE3_MEM_VIRT +#define CONFIG_SYS_PCIE3_IO_PHYS CONFIG_SYS_PCIE3_IO_VIRT + +#define CONFIG_PCI_SCAN_SHOW /* Show pci devices on startup */ + +/* + * Ethernet + */ + +#define CONFIG_ETHPRIME "ethernet@26000" /* Primary ethernet device */ + +/* + * USB + */ + +#define CONFIG_HAS_FSL_DR_USB +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET + +/* + * eSDHC + */ + +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define SDHC_WP_IS_GPIO /* SDHC_WP pin is not connected to SD card slot, it is GPIO pin */ + +/* + * ATA/SCSI + */ + +#define CONFIG_LBA48 /* Enable support for 137+ GB disks */ +#define CONFIG_SYS_64BIT_LBA /* Enable support for 2.1+ TB disks */ + +/* + * Miscellaneous configurable options + */ + +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* Allow baudrate change argument for loads */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ SZ_64M /* Initial Memory for Linux */ +#define CONFIG_SYS_BOOTM_LEN SZ_64M /* Increase max gunzip size */ + +/* + * Environment Configuration + */ + +#define BOOT_TARGET_DEVICES(func) \ + func(MMC, mmc, 0) \ + func(NVME, nvme, 0) \ + func(SCSI, scsi, 0) \ + func(USB, usb, 0) \ + func(USB, usb, 1) \ + func(USB, usb, 2) \ + func(USB, usb, 3) \ + func(USB, usb, 4) \ + func(UBIFS, ubifs, 0) \ + func(DHCP, dhcp, na) + +#include <config_distro_bootcmd.h> + +/* These boot source switches macros must be constant numbers as they are stringified */ +#define __SW_BOOT_MASK 0x03 +#define __SW_BOOT_NOR 0xc8 +#define __SW_BOOT_SPI 0x28 +#define __SW_BOOT_SD 0x68 +#define __SW_BOOT_SD2 0x18 +#define __SW_BOOT_NAND 0xe8 +#define __SW_BOOT_PCIE 0xa8 +#define __SW_NOR_BANK_MASK 0xfd +#define __SW_NOR_BANK_UP 0x00 +#define __SW_NOR_BANK_LO 0x02 +#define __SW_BOOT_NOR_BANK_UP 0xc8 /* (__SW_BOOT_NOR | __SW_NOR_BANK_UP) */ +#define __SW_BOOT_NOR_BANK_LO 0xca /* (__SW_BOOT_NOR | __SW_NOR_BANK_LO) */ +#define __SW_BOOT_NOR_BANK_MASK 0x01 /* (__SW_BOOT_MASK & __SW_NOR_BANK_MASK) */ + +#include "p1_p2_bootsrc.h" + +#define REBOOT_ENV_SETTINGS \ + RST_NOR_UP_CMD(reboot_to_nor, echo Rebooting to NOR bootloader;) \ + RST_SD_CMD(reboot_to_sd, echo Rebooting to SD bootloader;) \ + RST_DEF_CMD(reboot_to_def, echo Rebooting to default bootloader;) \ + "" + +#define BOOTCMD_RESCUE \ + "setenv bootargs root=mtd2 rw rootfstype=jffs2 console=ttyS0,115200; " \ + "bootm 0xef020000 - 0xef000000" \ + "" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "fdt_addr_r=0x2000000\0" \ + "kernel_addr_r=0x2100000\0" \ + "scriptaddr=0x3000000\0" \ + "pxefile_addr_r=0x3100000\0" \ + "ramdisk_addr_r=0x4000000\0" \ + "fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \ + "fdt_addr=0xef000000\0" \ + "bootubipart=rootfs\0" \ + "bootubivol=rootfs\0" \ + "bootcmd_rescue=" BOOTCMD_RESCUE "\0" \ + REBOOT_ENV_SETTINGS \ + BOOTENV + +#endif /* _CONFIG_TURRIS_1X_H */ -- 2.20.1

4 14

[PATCH] usb: eth: lan78xx: Fix logic in lan78xx_read_otp() to avoid a warning
by Tom Rini 20 Jun '23

20 Jun '23

In lan78xx_read_otp() we want to know if sig is LAN78XX_OTP_INDICATOR_1 or LAN78XX_OTP_INDICATOR_2. In the case of matching the first one we set offset to itself, and clang warns about this. Rework the logic so that if sig is the second indicator we adjust the offset as today and if it does not match the first indicator we return -EINVAL Cc: Marek Vasut <marex(a)denx.de> Signed-off-by: Tom Rini <trini(a)konsulko.com> --- drivers/usb/eth/lan78xx.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/drivers/usb/eth/lan78xx.c b/drivers/usb/eth/lan78xx.c index e34ad2603fbb..d147412990de 100644 --- a/drivers/usb/eth/lan78xx.c +++ b/drivers/usb/eth/lan78xx.c @@ -146,11 +146,9 @@ static int lan78xx_read_otp(struct usb_device *udev, u32 offset, ret = lan78xx_read_raw_otp(udev, 0, 1, &sig); if (!ret) { - if (sig == LAN78XX_OTP_INDICATOR_1) - offset = offset; - else if (sig == LAN78XX_OTP_INDICATOR_2) + if (sig == LAN78XX_OTP_INDICATOR_2) offset += 0x100; - else + else if (sig != LAN78XX_OTP_INDICATOR_1) return -EINVAL; ret = lan78xx_read_raw_otp(udev, offset, length, data); if (ret) -- 2.17.1

2 2