April 2021 - U-Boot

[PATCH 2/4] pinephone_defconfig: reduce boot delay
by Nicolas Boulenguez 03 Jun '21

03 Jun '21

From: Arnaud Ferraris <arnaud.ferraris(a)collabora.com> On a cellular phone, the vast majority of users can be expected to have no serial console connected and prefer a short boot. --- configs/pinephone_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/configs/pinephone_defconfig b/configs/pinephone_defconfig index 9967cddab9..9b51a7a100 100644 --- a/configs/pinephone_defconfig +++ b/configs/pinephone_defconfig @@ -10,4 +10,5 @@ CONFIG_PINEPHONE_DT_SELECTION=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-pinephone-1.2" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_BOOTDELAY=0 CONFIG_OF_LIST="sun50i-a64-pinephone-1.1 sun50i-a64-pinephone-1.2" -- 2.20.1

7 19

[PATCH] arm: dts: lx2162aqds: support eMMC HS400 mode on esdhc1
by Yangbo Lu 02 Jun '21

02 Jun '21

Add properties related to eMMC HS400 mode for esdhc1. Signed-off-by: Yangbo Lu <yangbo.lu(a)nxp.com> --- arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi | 6 ++++++ arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi | 6 ++++++ arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi | 6 ++++++ arch/arm/dts/fsl-lx2162a-qds.dts | 6 ++++++ 4 files changed, 24 insertions(+) diff --git a/arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi b/arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi index 60f5a4ee43..3b6fddba7c 100644 --- a/arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi +++ b/arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi @@ -56,3 +56,9 @@ reg = <0x3>; }; }; + +&esdhc1 { + mmc-hs200-1_8v; + mmc-hs400-1_8v; + bus-width = <8>; +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi b/arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi index 8e11b0680a..0f4329f587 100644 --- a/arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi +++ b/arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi @@ -59,3 +59,9 @@ reg = <0x1>; }; }; + +&esdhc1 { + mmc-hs200-1_8v; + mmc-hs400-1_8v; + bus-width = <8>; +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi b/arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi index faf4285eab..8c856a19d4 100644 --- a/arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi +++ b/arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi @@ -24,3 +24,9 @@ reg = <0x0>; }; }; + +&esdhc1 { + mmc-hs200-1_8v; + mmc-hs400-1_8v; + bus-width = <8>; +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds.dts b/arch/arm/dts/fsl-lx2162a-qds.dts index 341610ccf4..68cb328716 100644 --- a/arch/arm/dts/fsl-lx2162a-qds.dts +++ b/arch/arm/dts/fsl-lx2162a-qds.dts @@ -135,3 +135,9 @@ reg = <2>; }; }; + +&esdhc1 { + mmc-hs200-1_8v; + mmc-hs400-1_8v; + bus-width = <8>; +}; -- 2.25.1

2 2

[PATCH] armv8: layerscape: enable eMMC HS400 workarounds for LX2160A/LX2162A
by Yangbo Lu 02 Jun '21

02 Jun '21

Enable eMMC HS400 workarounds for LX2160A/LX2162A. Signed-off-by: Yangbo Lu <yangbo.lu(a)nxp.com> --- arch/arm/cpu/armv8/fsl-layerscape/Kconfig | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig index 9d1ba4c771..395e5ccaad 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig +++ b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig @@ -224,6 +224,8 @@ config ARCH_LX2162A select SYS_FSL_EC1 select SYS_FSL_EC2 select SYS_FSL_ERRATUM_A050106 + select SYS_FSL_ERRATUM_A011334 + select SYS_FSL_ESDHC_UNRELIABLE_PULSE_DETECTION_WORKAROUND select SYS_FSL_HAS_RGMII select SYS_FSL_HAS_SEC select SYS_FSL_HAS_CCN508 @@ -254,6 +256,8 @@ config ARCH_LX2160A select SYS_FSL_EC1 select SYS_FSL_EC2 select SYS_FSL_ERRATUM_A050106 + select SYS_FSL_ERRATUM_A011334 + select SYS_FSL_ESDHC_UNRELIABLE_PULSE_DETECTION_WORKAROUND select SYS_FSL_HAS_RGMII select SYS_FSL_HAS_SEC select SYS_FSL_HAS_CCN508 -- 2.25.1

2 2

RE: U-Boot "lib: Add support for ECDSA image signing" commit breaks socfpga_*_atf_defconfig compilation
by Lim, Elly Siew Chin 31 May '21

31 May '21

Add this discussion to denx mailing list. > -----Original Message----- > From: Simon Glass <sjg(a)chromium.org> > Sent: Saturday, April 24, 2021 3:29 AM > To: Lim, Elly Siew Chin <elly.siew.chin.lim(a)intel.com> > Cc: Alex G. <mr.nuke.me(a)gmail.com>; Tan, Ley Foon > <ley.foon.tan(a)intel.com>; Gan, Yau Wai <yau.wai.gan(a)intel.com> > Subject: Re: U-Boot "lib: Add support for ECDSA image signing" commit > breaks socfpga_*_atf_defconfig compilation > > Hi, > > On Sat, 24 Apr 2021 at 05:30, Lim, Elly Siew Chin <elly.siew.chin.lim(a)intel.com> > wrote: > > > > > > > > > -----Original Message----- > > > From: Lim, Elly Siew Chin > > > Sent: Saturday, April 24, 2021 1:17 AM > > > To: Alex G. <mr.nuke.me(a)gmail.com>; Simon Glass <sjg(a)chromium.org> > > > Cc: Tan, Ley Foon <ley.foon.tan(a)intel.com>; Gan, Yau Wai > > > <yau.wai.gan(a)intel.com> > > > Subject: RE: U-Boot "lib: Add support for ECDSA image signing" > > > commit breaks socfpga_*_atf_defconfig compilation > > > > > > Hi Alex, > > > > > > > -----Original Message----- > > > > From: Alex G. <mr.nuke.me(a)gmail.com> > > > > Sent: Saturday, April 24, 2021 1:07 AM > > > > To: Lim, Elly Siew Chin <elly.siew.chin.lim(a)intel.com>; Simon > > > > Glass <sjg(a)chromium.org> > > > > Cc: Tan, Ley Foon <ley.foon.tan(a)intel.com>; Gan, Yau Wai > > > > <yau.wai.gan(a)intel.com> > > > > Subject: Re: U-Boot "lib: Add support for ECDSA image signing" > > > > commit breaks socfpga_*_atf_defconfig compilation > > > > > > > > > > > > On 4/23/21 11:59 AM, Lim, Elly Siew Chin wrote: > > > > > Hi Alexandru, Simon, > > > > > > > > > > Commit > > > > > https://source.denx.de/u-boot/u-boot/- > > > > /commit/ed6c9e0b6668a05d62f5d1b7 > > > > > 5aecaf246ba51042 > > > > > <https://source.denx.de/u-boot/u-boot/- > > > > /commit/ed6c9e0b6668a05d62f5d1b > > > > > 75aecaf246ba51042> breaks Intel socfpga_*_atf_defconfig U-Boot > > > > > compilation due to openssl. > > > > > > > > > > This commit compile "u-boot/lib/ecdsa/ecdsa_libcrypto.c" based > > > > > on CONFIG_FIT_SIGNATURE, and ecdsa_libcrypto.c requires openssl. > > > > > > > > > > /ecdsa_libcrypto.c:/ > > > > > > > > > > /#include <openssl/ssl.h>/ > > > > > > > > > > /#include <openssl/ec.h>/ > > > > > > > > > > /#include <openssl/bn.h>/ > > > > > > > > > > However, in our use case (Intel socfpga_*_atf_defconfig) we use > > > > > CONFIG_FIT_SIGNATURE with CRC32 which does need openssl. > > > > > > > > It is my understanding that FIT_SIGNATURE implies cryptographic > support. > > > > In your case, I wouldtry disabling CONFIG_FIT_SIGNATURE and using > > > > a > > > > hash-1 node with algo value of "crc32". > > > > > > > > For example: > > > > > > > > /images { > > > > kernel-1 { > > > > ... > > > > > > > > hash-1 { > > > > algo = "crc32"; > > > > value = <autogenerated>; > > > > }; > > > > > > > > Alex > > > > > > > > > > > > > > CONFIG_FIT_SIGNATURE=y > > > > > > > > > > CONFIG_FIT_SIGNATURE_MAX_SIZE=0x10000000 > > > > > > > > > > CONFIG_SPL_FIT_SIGNATURE=y > > > > > > > > > > CONFIG_SPL_CRC32_SUPPORT=y > > > > > > > > > > We hit the following compilation error: > > > > > > > > > > /toolstools//liblib//ecdsaecdsa//ecdsaecdsa--libcrypto.olibcrypto.o:: > > > > > InIn functionfunction ``prepare_ctxprepare_ctx''::/ > > > > > > > > > > /ecdsaecdsa--libcrypto.clibcrypto.c::((..texttext++0x790x79)):: > > > > > undefinedundefined referencereference toto > > > > > ``OPENSSL_init_sslOPENSSL_init_ssl''/ > > > > > > > > > > Can you please help to help to add a new CONFIG > > > > (CONFIG_ECDSA_SUPPORT) > > > > > to gate the compilation of "ecdsa_libcrypto.c" which similar to > > > > > other algorithm? So that we can only compile when needed instead > > > > > of force all to support openssl. > > > > > > > > > > Reference: lib/rsa > > > > > > > > > > /obj-$(CONFIG_$(SPL_TPL_)RSA_VERIFY) += rsa-verify.o/ > > > > > > > > > > Thanks, > > > > > > > > > > Siew Chin > > > > > > > > > > > Our purpose is to use CRC32 as integrity check of binary file in FIT > > > image, so, we need to use FIT_SIGNATURE. And, we did add the hash > node in FIT image. > > (this thread should go to the mailing list) > > From my reading, fit_image_verify_with_data() still verifies the hash when > FIT_SIGNATURE is not enabled. It looks like spl_fit needs to use this same > behaviour. > > - Simon > Hi Simon, In our use case, we use FIT image in both first stage (FSBL) and second stage (FSBL) boot loader. (1) FSBL: SPL -> (u-boot.fit) -> ATF -> U-BOOT PROPER In this phase, only "FIT_SIGNATURE" does fit image data integrity check. CONFIG_SPL_FIT_SIGNATURE=y CONFIG_SPL_CRC32_SUPPORT=y common/spl/spl_fit.c if (CONFIG_IS_ENABLED(FIT_SIGNATURE)) { printf("## Checking hash(es) for Image %s ... ", fit_get_name(fit, node, NULL)); if (!fit_image_verify_with_data(fit, node, src, length)) return -EPERM; puts("OK\n"); } (2) SSBL: U-BOOT PROPER -> (kernel.itb, using bootm command) -> Linux In this phase, the code did support FIT data integrity check without FIT_SIGNATURE. bootm command will call "fit_all_image_verify" in image-fit.c. "fit_all_image_verify" function verify data integrity for all images if hash presented. cmd/bootm.c #if defined(CONFIG_FIT) case IMAGE_FORMAT_FIT: ... if (!fit_all_image_verify(hdr)) { puts("Bad hash in FIT image!\n"); unmap_sysmem(hdr); return 1; } #endif I can think of two enhancement to fix this: (1) Add separate CONFIG to gate ECDSA algorithm. This enhancement benefits all use cases. I assume not all user need ECDSA algorithm when FIT_SIGNATURE is used. (2) Enhance spl/spl_fit.c to support verification of data integrity based on hash(es) in FIT image instead of based on FIT_SIGNATURE. What do you think? If you agree: For (1), can we ask Alex's help to change it? For (2), who will be the right person to change this kind of common code? Thanks, Siew Chin > > > > > > Kindly refer to common/spl/spl_fit.c > > > if (CONFIG_IS_ENABLED(FIT_SIGNATURE)) { > > > printf("## Checking hash(es) for Image %s ... ", > > > fit_get_name(fit, node, NULL)); > > > if (!fit_image_verify_with_data(fit, node, src, length)) > > > return -EPERM; > > > puts("OK\n"); > > > } > > > > > > Results: > > > ## Checking hash(es) for config conf ... OK > > > ## Checking hash(es) for Image atf ... crc32+ OK > > > ## Checking hash(es) for Image uboot ... crc32+ OK > > > ## Checking hash(es) for Image fdt ... crc32+ OK > > > > > > Thanks, > > > Siew Chin > > > > > > Besides, kindly refer to function "calculate_hash" in common/image-fit.c, > FIT image did support multiple algorithm, CRC32 is one of it. And, the > common practice is each algorithm will gate by its specific CONFIG which > allow us to only compile the source files when needed. > > > > int calculate_hash(const void *data, int data_len, const char *algo, > > uint8_t *value, int *value_len) { > > if (IMAGE_ENABLE_CRC32 && strcmp(algo, "crc32") == 0) { > > *((uint32_t *)value) = crc32_wd(0, data, data_len, > > CHUNKSZ_CRC32); > > *((uint32_t *)value) = cpu_to_uimage(*((uint32_t *)value)); > > *value_len = 4; > > } else if (IMAGE_ENABLE_SHA1 && strcmp(algo, "sha1") == 0) { > > sha1_csum_wd((unsigned char *)data, data_len, > > (unsigned char *)value, CHUNKSZ_SHA1); > > *value_len = 20; > > } else if (IMAGE_ENABLE_SHA256 && strcmp(algo, "sha256") == 0) { > > sha256_csum_wd((unsigned char *)data, data_len, > > (unsigned char *)value, CHUNKSZ_SHA256); > > *value_len = SHA256_SUM_LEN; > > } else if (IMAGE_ENABLE_SHA384 && strcmp(algo, "sha384") == 0) { > > sha384_csum_wd((unsigned char *)data, data_len, > > (unsigned char *)value, CHUNKSZ_SHA384); > > *value_len = SHA384_SUM_LEN; > > } else if (IMAGE_ENABLE_SHA512 && strcmp(algo, "sha512") == 0) { > > sha512_csum_wd((unsigned char *)data, data_len, > > (unsigned char *)value, CHUNKSZ_SHA512); > > *value_len = SHA512_SUM_LEN; > > } else if (IMAGE_ENABLE_MD5 && strcmp(algo, "md5") == 0) { > > md5_wd((unsigned char *)data, data_len, value, CHUNKSZ_MD5); > > *value_len = 16; > > } else { > > debug("Unsupported hash alogrithm\n"); > > return -1; > > } > > return 0; > > } > > > > Thanks, > > Siew Chin > >

2 1

[PATCH v3 0/5] stm32mp: Enable OP-TEE and TZC support in SPL
by Alexandru Gagniuc 31 May '21

31 May '21

The purpose of this series is to allow booting an OP-TEE image from SPL, by corectly configuring the TrustZone (TZC) memory regions. Although TZC400 is a generic silicon logic that could apply to other mach- families, support is currently restricted to stm32mp. I have neither a feasible way nor interest in validating this for other chips. It's fairly trivial to move the code from mach- to arch/, should another use case arise. The configuration of the memory regions is devicetree-driven, so there isn't much to hardcode, However the delineation between OP-TEE secure memory and shared memory is not given in the devicetree. This is the one thing that has to be hardcoded. Changes since v2: - Use ram_get_info() instead of ofnode_read("st,mem-size") - Only hardcode shared memory size instead of TZDRAM size - Use log_info() instead of pr_info() Changes since v1: - Removed "Weak functions are stupid" comment - Addressed blank line complaints from checkpatch Alexandru Gagniuc (5): spl: mmc: Support OP-TEE payloads in Falcon mode spl: Introduce spl_board_prepare_for_optee() hook arm: stm32mp: Implement support for TZC 400 controller stm32mp1: spl: Configure TrustZone controller for OP-TEE ARM: dts: stm32mp: Add OP-TEE reserved memory to SPL dtb arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi | 3 + arch/arm/mach-stm32mp/Makefile | 1 + arch/arm/mach-stm32mp/include/mach/tzc.h | 33 ++++++ arch/arm/mach-stm32mp/spl.c | 90 +++++++++++++++ arch/arm/mach-stm32mp/tzc400.c | 136 +++++++++++++++++++++++ common/spl/spl.c | 5 + common/spl/spl_mmc.c | 6 +- include/spl.h | 14 +++ 8 files changed, 286 insertions(+), 2 deletions(-) create mode 100644 arch/arm/mach-stm32mp/include/mach/tzc.h create mode 100644 arch/arm/mach-stm32mp/tzc400.c -- 2.26.3

3 10

[PATCH v6] imx: support for conga-QMX8 board
by Oliver Graute 31 May '21

31 May '21

Add i.MX8QM qmx8 congatec board support U-Boot 2021.04-rc1-00070-gcc181a2ad4 (Feb 19 2021 - 13:15:49 +0100) CPU: NXP i.MX8QM RevB A53 at 1200 MHz Model: Congatec QMX8 Qseven series Board: conga-QMX8 Build: SCFW 494c97f3, SECO-FW d7523fe8, ATF 09c5cc9 Boot: SD2 DRAM: 6 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 switch to partitions #0, OK mmc2 is current device Net: Error: ethernet@5b040000 address not set. No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Oliver Graute <oliver.graute(a)kococonnector.com> Cc: Stefano Babic <sbabic(a)denx.de> Cc: Fabio Estevam <festevam(a)gmail.com> Cc: Peng Fan <peng.fan(a)nxp.com> Cc: Simon Glass <sjg(a)chromium.org> Cc: Ye Li <ye.li(a)nxp.com> Cc: uboot-imx <uboot-imx(a)nxp.com> --- These changes are based on this vendor tree: git.congatec.com/imx8_early_access/imx8_uboot_internal.git Changes for v6: - fixed build warnings because of missing prototypes Changes for v5: - fixed checkpatch errors - fixed some checkpatch warnings Changes for v4: - fixed missing DTS file in MAINTAINERS - replaced bd_t with struct bd_info - replaced README with imx8qm-dmsse20-a1.rst - move CMD_FUSE to Kconfig - replaced power_domain_lookup_name with imx8_power_domain_lookup_name Changes for v3: - include log.h - include delay.h - improved README - set phy register to six - Remove 'fdt_high' and 'initrd_high' environment variables - set CONFIG_SYS_BOOTMAPSZ to 256MB - increased CONFIG_SYS_FSL_USDHC_NUM to 3 Changes for v2: - added USDHC3_BASE_ADDR - replaced CONFIG_FSL_ESDHC with CONFIG_FSL_ESDHC_IMX - set CONFIG_FEC_MXC_PHYADDR to -1 - moved CONFIG_ENV_SIZE and CONFIG_ENV_OFFSET to defconfig arch/arm/dts/Makefile | 1 + arch/arm/dts/imx8qm-cgtqmx8.dts | 404 ++++++++++++++++++++++++ arch/arm/mach-imx/imx8/Kconfig | 7 + board/congatec/cgtqmx8/Kconfig | 14 + board/congatec/cgtqmx8/MAINTAINERS | 7 + board/congatec/cgtqmx8/Makefile | 11 + board/congatec/cgtqmx8/cgtqmx8.c | 460 ++++++++++++++++++++++++++++ board/congatec/cgtqmx8/imximage.cfg | 21 ++ board/congatec/cgtqmx8/spl.c | 77 +++++ board/congatec/common/Kconfig | 48 +++ board/congatec/common/Makefile | 23 ++ board/congatec/common/mmc.c | 50 +++ configs/cgtqmx8_defconfig | 86 ++++++ doc/board/congatec/cgtqmx8.rst | 70 +++++ doc/board/congatec/index.rst | 9 + include/configs/cgtqmx8.h | 181 +++++++++++ 16 files changed, 1469 insertions(+) create mode 100644 arch/arm/dts/imx8qm-cgtqmx8.dts create mode 100644 board/congatec/cgtqmx8/Kconfig create mode 100644 board/congatec/cgtqmx8/MAINTAINERS create mode 100644 board/congatec/cgtqmx8/Makefile create mode 100644 board/congatec/cgtqmx8/cgtqmx8.c create mode 100644 board/congatec/cgtqmx8/imximage.cfg create mode 100644 board/congatec/cgtqmx8/spl.c create mode 100644 board/congatec/common/Kconfig create mode 100644 board/congatec/common/Makefile create mode 100644 board/congatec/common/mmc.c create mode 100644 configs/cgtqmx8_defconfig create mode 100644 doc/board/congatec/cgtqmx8.rst create mode 100644 doc/board/congatec/index.rst create mode 100644 include/configs/cgtqmx8.h diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 858b79ac97..23f5a59a08 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -773,6 +773,7 @@ dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-com.dtb \ dtb-$(CONFIG_ARCH_IMX8) += \ fsl-imx8qm-apalis.dtb \ fsl-imx8qm-mek.dtb \ + imx8qm-cgtqmx8.dtb \ imx8qm-rom7720-a1.dtb \ fsl-imx8qxp-ai_ml.dtb \ fsl-imx8qxp-colibri.dtb \ diff --git a/arch/arm/dts/imx8qm-cgtqmx8.dts b/arch/arm/dts/imx8qm-cgtqmx8.dts new file mode 100644 index 0000000000..555c357f6f --- /dev/null +++ b/arch/arm/dts/imx8qm-cgtqmx8.dts @@ -0,0 +1,404 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2016 Freescale Semiconductor, Inc. + * Copyright 2017 NXP + * Copyright 2017 congatec AG + * Copyright (C) 2019 Oliver Graute <oliver.graute(a)kococonnector.com> + */ + +/dts-v1/; + +/* First 128KB is for PSCI ATF. */ +/memreserve/ 0x80000000 0x00020000; + +#include "fsl-imx8qm.dtsi" + +/ { + model = "Congatec QMX8 Qseven series"; + compatible = "fsl,imx8qm-qmx8", "fsl,imx8qm"; + + chosen { + bootargs = "console=ttyLP0,115200 earlycon=lpuart32,0x5a060000,115200"; + stdout-path = &lpuart0; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_usdhc2_vmmc: usdhc2_vmmc { + compatible = "regulator-fixed"; + regulator-name = "sw-3p3-sd1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + off-on-delay-us = <3000>; + }; + + reg_usdhc3_vmmc: usdhc3_vmmc { + compatible = "regulator-fixed"; + regulator-name = "sw-3p3-sd2"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + off-on-delay-us = <3000>; + }; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii"; + phy-handle = <&ethphy0>; + fsl,magic-packet; + fsl,rgmii_txc_dly; + fsl,rgmii_rxc_dly; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@6 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <6>; + at803x,eee-disabled; + at803x,vddio-1p8v; + }; + }; +}; + +&gpio2 { + status = "okay"; +}; + +&gpio5 { + status = "okay"; +}; + +&i2c0 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpi2c0>; + clock-frequency = <100000>; + status = "okay"; + + rtc_ext: m41t62@68 { + compatible = "st,m41t62"; + reg = <0x68>; + }; +}; + +&i2c1 { + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpi2c1>; + status = "okay"; + + wm8904: wm8904@1a { + compatible = "wlf,wm8904"; + reg = <0x1a>; + + clocks = <&clk IMX8QM_AUD_MCLKOUT0>; + clock-names = "mclk"; + wlf,shared-lrclk; + /* power-domains = <&pd_mclk_out0>; */ + + assigned-clocks = <&clk IMX8QM_AUD_PLL0_DIV>, + <&clk IMX8QM_AUD_ACM_AUD_PLL_CLK0_DIV>, + <&clk IMX8QM_AUD_ACM_AUD_REC_CLK0_DIV>, + <&clk IMX8QM_AUD_MCLKOUT0>; + + assigned-clock-rates = <786432000>, <49152000>, <24576000>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx8qm-qmx8 { + + pinctrl_hog: hoggrp{ + fsl,pins = < + SC_P_M40_GPIO0_01_LSIO_GPIO0_IO09 0x00000021 + SC_P_USB_SS3_TC1_LSIO_GPIO4_IO04 0x00000021 + SC_P_M40_GPIO0_00_LSIO_GPIO0_IO08 0x00000021 + SC_P_ESAI1_SCKT_LSIO_GPIO2_IO07 0x00000021 + SC_P_SPDIF0_TX_LSIO_GPIO2_IO15 0x00000021 + SC_P_FLEXCAN1_RX_LSIO_GPIO3_IO31 0x00000021 + SC_P_ESAI1_TX0_LSIO_GPIO2_IO08 0x00000021 + SC_P_FLEXCAN1_TX_LSIO_GPIO4_IO00 0x00000021 + SC_P_ESAI1_TX1_LSIO_GPIO2_IO09 0x00000021 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + SC_P_ENET0_MDC_CONN_ENET0_MDC 0x06000020 + SC_P_ENET0_MDIO_CONN_ENET0_MDIO 0x06000020 + SC_P_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x06000020 + SC_P_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x06000020 + SC_P_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x06000020 + SC_P_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x06000020 + SC_P_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x06000020 + SC_P_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x06000020 + SC_P_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x06000020 + SC_P_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x06000020 + SC_P_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x06000020 + SC_P_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x06000020 + SC_P_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x06000020 + SC_P_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x06000020 + >; + }; + + pinctrl_lpi2c0: lpi2c0grp { + fsl,pins = < + SC_P_HDMI_TX0_TS_SCL_DMA_I2C0_SCL 0xc600004c + SC_P_HDMI_TX0_TS_SDA_DMA_I2C0_SDA 0xc600004c + >; + }; + + pinctrl_lpi2c1: lpi2c1grp { + fsl,pins = < + SC_P_GPT0_CLK_DMA_I2C1_SCL 0xc600004c + SC_P_GPT0_CAPTURE_DMA_I2C1_SDA 0xc600004c + >; + }; + + pinctrl_lpuart0: lpuart0grp { + fsl,pins = < + SC_P_UART0_RX_DMA_UART0_RX 0x06000020 + SC_P_UART0_TX_DMA_UART0_TX 0x06000020 + >; + }; + + pinctrl_lpuart1: lpuart1grp { + fsl,pins = < + SC_P_UART1_RX_DMA_UART1_RX 0x06000020 + SC_P_UART1_TX_DMA_UART1_TX 0x06000020 + SC_P_UART1_CTS_B_DMA_UART1_CTS_B 0x06000020 + SC_P_UART1_RTS_B_DMA_UART1_RTS_B 0x06000020 + >; + }; + + pinctrl_lpuart3: lpuart3grp { + fsl,pins = < + SC_P_M41_GPIO0_00_DMA_UART3_RX 0x06000020 + SC_P_M41_GPIO0_01_DMA_UART3_TX 0x06000020 + >; + }; + + pinctrl_mlb: mlbgrp { + fsl,pins = < + SC_P_MLB_SIG_CONN_MLB_SIG 0x21 + SC_P_MLB_CLK_CONN_MLB_CLK 0x21 + SC_P_MLB_DATA_CONN_MLB_DATA 0x21 + >; + }; + + pinctrl_isl29023: isl29023grp { + fsl,pins = < + SC_P_ADC_IN2_LSIO_GPIO3_IO20 0x00000021 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + SC_P_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041 + SC_P_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021 + SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021 + SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021 + SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021 + SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021 + SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021 + SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021 + SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021 + SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021 + SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000041 + SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000021 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { + fsl,pins = < + SC_P_EMMC0_CLK_CONN_EMMC0_CLK 0x06000040 + SC_P_EMMC0_CMD_CONN_EMMC0_CMD 0x00000020 + SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000020 + SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000020 + SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000020 + SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000020 + SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000020 + SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000020 + SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000020 + SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000020 + SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000040 + SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000020 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { + fsl,pins = < + SC_P_EMMC0_CLK_CONN_EMMC0_CLK 0x06000040 + SC_P_EMMC0_CMD_CONN_EMMC0_CMD 0x00000020 + SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000020 + SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000020 + SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000020 + SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000020 + SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000020 + SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000020 + SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000020 + SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000020 + SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000040 + SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000020 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2grpgpio { + fsl,pins = < + SC_P_USDHC1_DATA6_LSIO_GPIO5_IO21 0x00000021 + SC_P_USDHC1_DATA7_LSIO_GPIO5_IO22 0x00000021 + SC_P_USDHC1_RESET_B_LSIO_GPIO4_IO07 0x00000021 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + SC_P_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041 + SC_P_USDHC1_CMD_CONN_USDHC1_CMD 0x00000021 + SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000021 + SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000021 + SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000021 + SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000021 + SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + SC_P_USDHC1_CLK_CONN_USDHC1_CLK 0x06000040 + SC_P_USDHC1_CMD_CONN_USDHC1_CMD 0x00000020 + SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000020 + SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000020 + SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000020 + SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000020 + SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000020 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + SC_P_USDHC1_CLK_CONN_USDHC1_CLK 0x06000040 + SC_P_USDHC1_CMD_CONN_USDHC1_CMD 0x00000020 + SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000020 + SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000020 + SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000020 + SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000020 + SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000020 + >; + }; + + pinctrl_usdhc3_gpio: usdhc3grpgpio { + fsl,pins = < + SC_P_USDHC2_RESET_B_LSIO_GPIO4_IO09 0x00000021 + SC_P_USDHC2_CD_B_LSIO_GPIO4_IO12 0x00000021 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + SC_P_USDHC2_CLK_CONN_USDHC2_CLK 0x06000041 + SC_P_USDHC2_CMD_CONN_USDHC2_CMD 0x00000021 + SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0 0x00000021 + SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1 0x00000021 + SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2 0x00000021 + SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3 0x00000021 + SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT 0x00000021 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3grp100mhz { + fsl,pins = < + SC_P_USDHC2_CLK_CONN_USDHC2_CLK 0x06000040 + SC_P_USDHC2_CMD_CONN_USDHC2_CMD 0x00000020 + SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0 0x00000020 + SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1 0x00000020 + SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2 0x00000020 + SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3 0x00000020 + SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT 0x00000020 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3grp200mhz { + fsl,pins = < + SC_P_USDHC2_CLK_CONN_USDHC2_CLK 0x06000040 + SC_P_USDHC2_CMD_CONN_USDHC2_CMD 0x00000020 + SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0 0x00000020 + SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1 0x00000020 + SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2 0x00000020 + SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3 0x00000020 + SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT 0x00000020 + >; + }; + }; +}; + +&lpuart0 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart0>; + status = "okay"; +}; + +&lpuart1 { /* Q7 connector */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart1>; + status = "okay"; +}; + +&pd_dma_lpuart0 { + debug_console; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + bus-width = <4>; + cd-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>; + vmmc-supply = <&reg_usdhc2_vmmc>; + fsl,tuning-start-tap = <20>; + fsl,tuning-step= <2>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_gpio>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_usdhc3_gpio>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_usdhc3_gpio>; + bus-width = <4>; + cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; + vmmc-supply = <&reg_usdhc3_vmmc>; + fsl,tuning-start-tap = <20>; + fsl,tuning-step= <2>; + status = "okay"; +}; diff --git a/arch/arm/mach-imx/imx8/Kconfig b/arch/arm/mach-imx/imx8/Kconfig index 04b9729109..6728d23b6b 100644 --- a/arch/arm/mach-imx/imx8/Kconfig +++ b/arch/arm/mach-imx/imx8/Kconfig @@ -85,6 +85,12 @@ config TARGET_IMX8QM_MEK select BOARD_LATE_INIT select IMX8QM +config TARGET_CONGA_QMX8 + bool "Support congatec conga-QMX8 board" + select BOARD_LATE_INIT + select SUPPORT_SPL + select IMX8QM + config TARGET_IMX8QM_ROM7720_A1 bool "Support i.MX8QM ROM-7720-A1" select BOARD_LATE_INIT @@ -100,6 +106,7 @@ endchoice source "board/freescale/imx8qm_mek/Kconfig" source "board/freescale/imx8qxp_mek/Kconfig" +source "board/congatec/cgtqmx8/Kconfig" source "board/advantech/imx8qm_rom7720_a1/Kconfig" source "board/toradex/apalis-imx8/Kconfig" source "board/toradex/colibri-imx8x/Kconfig" diff --git a/board/congatec/cgtqmx8/Kconfig b/board/congatec/cgtqmx8/Kconfig new file mode 100644 index 0000000000..7273039261 --- /dev/null +++ b/board/congatec/cgtqmx8/Kconfig @@ -0,0 +1,14 @@ +if TARGET_CONGA_QMX8 + +config SYS_BOARD + default "cgtqmx8" + +config SYS_VENDOR + default "congatec" + +config SYS_CONFIG_NAME + default "cgtqmx8" + +source "board/congatec/common/Kconfig" + +endif diff --git a/board/congatec/cgtqmx8/MAINTAINERS b/board/congatec/cgtqmx8/MAINTAINERS new file mode 100644 index 0000000000..53bc0f93b7 --- /dev/null +++ b/board/congatec/cgtqmx8/MAINTAINERS @@ -0,0 +1,7 @@ +i.MX8QM CGTQMX8 BOARD +M: Oliver Graute <oliver.graute(a)kococonnector.com> +S: Maintained +F: board/congatec/cgtqmx8/ +F: arch/arm/dts/imx8qm-cgtqmx8.dts +F: include/configs/cgtqmx8.h +F: configs/cgtqmx8_defconfig diff --git a/board/congatec/cgtqmx8/Makefile b/board/congatec/cgtqmx8/Makefile new file mode 100644 index 0000000000..4b59dbb6bc --- /dev/null +++ b/board/congatec/cgtqmx8/Makefile @@ -0,0 +1,11 @@ +# +# Copyright 2017 NXP +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += cgtqmx8.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +endif diff --git a/board/congatec/cgtqmx8/cgtqmx8.c b/board/congatec/cgtqmx8/cgtqmx8.c new file mode 100644 index 0000000000..fb0cf09138 --- /dev/null +++ b/board/congatec/cgtqmx8/cgtqmx8.c @@ -0,0 +1,460 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 congatec AG + * Copyright (C) 2019 Oliver Graute <oliver.graute(a)kococonnector.com> + */ +#include <common.h> +#include <errno.h> +#include <linux/libfdt.h> +#include <fsl_esdhc.h> +#include <init.h> + +#include <asm/io.h> +#include <asm/gpio.h> +#include <asm/arch/clock.h> +#include <asm/arch/sci/sci.h> +#include <asm/arch/imx8-pins.h> +#include <usb.h> +#include <asm/arch/iomux.h> +#include <asm/arch/sys_proto.h> +#include <linux/delay.h> +#include <power-domain.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define ESDHC_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define ESDHC_CLK_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define ENET_INPUT_PAD_CTRL ((SC_PAD_CONFIG_OD_IN << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define ENET_NORMAL_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define FSPI_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define GPIO_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define I2C_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_LOW << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +static iomux_cfg_t uart0_pads[] = { + SC_P_UART0_RX | MUX_PAD_CTRL(UART_PAD_CTRL), + SC_P_UART0_TX | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +void board_late_mmc_env_init(void); +void init_clk_usdhc(u32 index); +int fsl_esdhc_initialize(struct bd_info *bis, struct fsl_esdhc_cfg *cfg); + +static void setup_iomux_uart(void) +{ + imx8_iomux_setup_multiple_pads(uart0_pads, ARRAY_SIZE(uart0_pads)); +} + +int board_early_init_f(void) +{ + /* sc_ipc_t ipcHndl = 0; */ + sc_err_t scierr = 0; + + /* When start u-boot in XEN VM, directly return */ + /* if (IS_ENABLED(CONFIG_XEN)) */ + /* return 0; */ + + /* ipcHndl = gd->arch.ipc_channel_handle; */ + + /* Power up UART0, this is very early while power domain is not working */ + scierr = sc_pm_set_resource_power_mode(-1, SC_R_UART_0, SC_PM_PW_MODE_ON); + if (scierr != SC_ERR_NONE) + return 0; + + /* Set UART0 clock root to 80 MHz */ + sc_pm_clock_rate_t rate = 80000000; + + scierr = sc_pm_set_clock_rate(-1, SC_R_UART_0, 2, &rate); + if (scierr != SC_ERR_NONE) + return 0; + + /* Enable UART0 clock root */ + scierr = sc_pm_clock_enable(-1, SC_R_UART_0, 2, true, false); + if (scierr != SC_ERR_NONE) + return 0; + + setup_iomux_uart(); + + return 0; +} + +#if IS_ENABLED(CONFIG_FSL_ESDHC_IMX) + +#define USDHC1_CD_GPIO IMX_GPIO_NR(5, 22) +#define USDHC2_CD_GPIO IMX_GPIO_NR(4, 12) + +static struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = { + {USDHC1_BASE_ADDR, 0, 8}, + {USDHC2_BASE_ADDR, 0, 4}, + {USDHC3_BASE_ADDR, 0, 4}, +}; + +static iomux_cfg_t emmc0[] = { + SC_P_EMMC0_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL), + SC_P_EMMC0_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA4 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA5 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA6 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_DATA7 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_EMMC0_STROBE | MUX_PAD_CTRL(ESDHC_PAD_CTRL), +}; + +static iomux_cfg_t usdhc1_sd[] = { + SC_P_USDHC1_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL), + SC_P_USDHC1_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_DATA6 | MUX_MODE_ALT(2) | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_DATA7 | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC1_VSELECT | MUX_PAD_CTRL(ESDHC_PAD_CTRL), +}; + +static iomux_cfg_t usdhc2_sd[] = { + SC_P_USDHC2_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL), + SC_P_USDHC2_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_VSELECT | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_WP | MUX_PAD_CTRL(ESDHC_PAD_CTRL), + SC_P_USDHC2_CD_B | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL), +}; + +int board_mmc_init(struct bd_info *bis) +{ + int i, ret; + struct power_domain pd; + + /* + * According to the board_mmc_init() the following map is done: + * (U-Boot device node) (Physical Port) + * mmc0 (onboard eMMC) USDHC1 + * mmc1 (external SD card) USDHC2 + * mmc2 (onboard µSD) USDHC3 + */ + for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { + switch (i) { + case 0: + /* onboard eMMC */ + if (!imx8_power_domain_lookup_name("conn_sdhc0", &pd)) + power_domain_on(&pd); + + imx8_iomux_setup_multiple_pads(emmc0, ARRAY_SIZE(emmc0)); + init_clk_usdhc(0); + usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); + break; + case 1: + /* external SD card */ + if (!imx8_power_domain_lookup_name("conn_sdhc1", &pd)) + power_domain_on(&pd); + + imx8_iomux_setup_multiple_pads(usdhc1_sd, ARRAY_SIZE(usdhc1_sd)); + init_clk_usdhc(1); + usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); + gpio_request(USDHC1_CD_GPIO, "sd1_cd"); + gpio_direction_input(USDHC1_CD_GPIO); + break; + case 2: + /* onboard µSD */ + if (!imx8_power_domain_lookup_name("conn_sdhc2", &pd)) + power_domain_on(&pd); + + imx8_iomux_setup_multiple_pads(usdhc2_sd, ARRAY_SIZE(usdhc2_sd)); + init_clk_usdhc(2); + usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); + gpio_request(USDHC2_CD_GPIO, "sd2_cd"); + gpio_direction_input(USDHC2_CD_GPIO); + break; + default: + printf("Warning: you configured more USDHC controllers" + "(%d) than supported by the board\n", i + 1); + return 0; + } + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); + if (ret) { + printf("Warning: failed to initialize mmc dev %d\n", i); + return ret; + } + } + + return 0; +} + +int board_mmc_getcd(struct mmc *mmc) +{ + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; + int ret = 0; + + switch (cfg->esdhc_base) { + case USDHC1_BASE_ADDR: + ret = 1; + break; + case USDHC2_BASE_ADDR: + ret = !gpio_get_value(USDHC1_CD_GPIO); + break; + case USDHC3_BASE_ADDR: + ret = !gpio_get_value(USDHC2_CD_GPIO); + break; + } + + return ret; +} + +#endif /* CONFIG_FSL_ESDHC_IMX */ + +#if (IS_ENABLED(CONFIG_FEC_MXC)) + +#include <miiphy.h> + +static iomux_cfg_t pad_enet0[] = { + SC_P_ENET0_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL), + SC_P_ENET0_RGMII_RXD0 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL), + SC_P_ENET0_RGMII_RXD1 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL), + SC_P_ENET0_RGMII_RXD2 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL), + SC_P_ENET0_RGMII_RXD3 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL), + SC_P_ENET0_RGMII_RXC | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL), + SC_P_ENET0_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_RGMII_TXD0 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_RGMII_TXD1 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_RGMII_TXD2 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_RGMII_TXD3 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_RGMII_TXC | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_MDC | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + SC_P_ENET0_MDIO | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), +}; + +static void setup_iomux_fec(void) +{ + imx8_iomux_setup_multiple_pads(pad_enet0, ARRAY_SIZE(pad_enet0)); +} + +static void enet_device_phy_reset(void) +{ + gpio_set_value(FEC0_RESET, 0); + udelay(50); + gpio_set_value(FEC0_RESET, 1); + + /* The board has a long delay for this reset to become stable */ + mdelay(200); +} + +int board_eth_init(struct bd_info *bis) +{ + setup_iomux_fec(); + + return 0; +} + +int board_phy_config(struct phy_device *phydev) +{ + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8); + + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); + + if (phydev->drv->config) + phydev->drv->config(phydev); + + return 0; +} + +static int setup_fec(void) +{ + /* Reset ENET PHY */ + enet_device_phy_reset(); + + return 0; +} +#endif + +#ifdef CONFIG_MXC_GPIO + +#define LVDS_ENABLE IMX_GPIO_NR(1, 6) +#define BKL_ENABLE IMX_GPIO_NR(1, 7) + +static iomux_cfg_t board_gpios[] = { + SC_P_LVDS0_I2C0_SCL | MUX_MODE_ALT(3) | MUX_PAD_CTRL(GPIO_PAD_CTRL), + SC_P_LVDS0_I2C0_SDA | MUX_MODE_ALT(3) | MUX_PAD_CTRL(GPIO_PAD_CTRL), + SC_P_ESAI1_FST | MUX_MODE_ALT(3) | MUX_PAD_CTRL(GPIO_PAD_CTRL), +}; + +static void board_gpio_init(void) +{ + imx8_iomux_setup_multiple_pads(board_gpios, ARRAY_SIZE(board_gpios)); + + /* enable LVDS */ + gpio_request(LVDS_ENABLE, "lvds_enable"); + gpio_direction_output(LVDS_ENABLE, 1); + + /* enable backlight */ + gpio_request(BKL_ENABLE, "bkl_enable"); + gpio_direction_output(BKL_ENABLE, 1); + + /* ethernet reset */ + gpio_request(FEC0_RESET, "enet0_reset"); + gpio_direction_output(FEC0_RESET, 1); +} +#endif + +int checkboard(void) +{ + puts("Board: conga-QMX8\n"); + + build_info(); + print_bootinfo(); + + return 0; +} + +int board_init(void) +{ + if (IS_ENABLED(CONFIG_XEN)) + return 0; + +#ifdef CONFIG_MXC_GPIO + board_gpio_init(); +#endif + +#if (IS_ENABLED(CONFIG_FEC_MXC)) + setup_fec(); +#endif + + return 0; +} + +void detail_board_ddr_info(void) +{ + puts("\nDDR "); +} + +/* + * Board specific reset that is system reset. + */ +void reset_cpu(ulong addr) +{ + /* TODO */ +} + +#ifdef CONFIG_OF_BOARD_SETUP +int ft_board_setup(void *blob, struct bd_info *bd) +{ + return 0; +} +#endif + +int board_mmc_get_env_dev(int devno) +{ + /* Use EMMC */ + if (IS_ENABLED(CONFIG_XEN)) + return 0; + + return devno; +} + +int mmc_map_to_kernel_blk(int dev_no) +{ + /* Use EMMC */ + if (IS_ENABLED(CONFIG_XEN)) + return 0; + + return dev_no; +} + +extern u32 _end_ofs; +int board_late_init(void) +{ +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + env_set("board_name", "QMX8"); + env_set("board_rev", "iMX8QM"); +#endif + + env_set("sec_boot", "no"); +#ifdef CONFIG_AHAB_BOOT + env_set("sec_boot", "yes"); +#endif + +#ifdef CONFIG_ENV_IS_IN_MMC + board_late_mmc_env_init(); +#endif + +#ifdef IMX_LOAD_HDMI_FIMRWARE + char *end_of_uboot; + char command[256]; + + end_of_uboot = (char *)(ulong)(CONFIG_SYS_TEXT_BASE + _end_ofs + + fdt_totalsize(gd->fdt_blob)); + end_of_uboot += 9; + + /* load hdmitxfw.bin and hdmirxfw.bin*/ + memcpy(IMX_HDMI_FIRMWARE_LOAD_ADDR, end_of_uboot, + IMX_HDMITX_FIRMWARE_SIZE + IMX_HDMIRX_FIRMWARE_SIZE); + + sprintf(command, "hdp load 0x%x", IMX_HDMI_FIRMWARE_LOAD_ADDR); + run_command(command, 0); + + sprintf(command, "hdprx load 0x%x", + IMX_HDMI_FIRMWARE_LOAD_ADDR + IMX_HDMITX_FIRMWARE_SIZE); + run_command(command, 0); +#endif + + return 0; +} + +#ifdef CONFIG_FSL_FASTBOOT +#ifdef CONFIG_ANDROID_RECOVERY +int is_recovery_key_pressing(void) +{ + return 0; /*TODO*/ +} +#endif /*CONFIG_ANDROID_RECOVERY*/ +#endif /*CONFIG_FSL_FASTBOOT*/ + +/* Only Enable USB3 resources currently */ +int board_usb_init(int index, enum usb_init_type init) +{ + return 0; +} diff --git a/board/congatec/cgtqmx8/imximage.cfg b/board/congatec/cgtqmx8/imximage.cfg new file mode 100644 index 0000000000..e324c7ca37 --- /dev/null +++ b/board/congatec/cgtqmx8/imximage.cfg @@ -0,0 +1,21 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2018 NXP + */ + +#define __ASSEMBLY__ + +/* Boot from SD, sector size 0x400 */ +BOOT_FROM SD 0x400 +/* SoC type IMX8QM */ +SOC_TYPE IMX8QM +/* Append seco container image */ +APPEND mx8qm-ahab-container.img +/* Create the 2nd container */ +CONTAINER +/* Add scfw image with exec attribute */ +IMAGE SCU mx8qm-val-scfw-tcm.bin +/* Add ATF image with exec attribute */ +IMAGE A35 bl31.bin 0x80000000 +/* Add U-Boot image with load attribute */ +DATA A35 u-boot-dtb.bin 0x80020000 diff --git a/board/congatec/cgtqmx8/spl.c b/board/congatec/cgtqmx8/spl.c new file mode 100644 index 0000000000..2a5d4c1bcd --- /dev/null +++ b/board/congatec/cgtqmx8/spl.c @@ -0,0 +1,77 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 NXP + * + */ + +#include <common.h> +#include <dm.h> +#include <init.h> +#include <log.h> +#include <spl.h> +#include <dm/uclass.h> +#include <dm/device.h> +#include <dm/uclass-internal.h> +#include <dm/device-internal.h> +#include <dm/lists.h> + +DECLARE_GLOBAL_DATA_PTR; + +void spl_board_init(void) +{ + struct udevice *dev; + int offset; + + uclass_find_first_device(UCLASS_MISC, &dev); + + for (; dev; uclass_find_next_device(&dev)) { + if (device_probe(dev)) + continue; + } + + offset = fdt_node_offset_by_compatible(gd->fdt_blob, -1, "nxp,imx8-pd"); + while (offset != -FDT_ERR_NOTFOUND) { + lists_bind_fdt(gd->dm_root, offset_to_ofnode(offset), + NULL, true); + offset = fdt_node_offset_by_compatible(gd->fdt_blob, offset, + "nxp,imx8-pd"); + } + + uclass_find_first_device(UCLASS_POWER_DOMAIN, &dev); + + for (; dev; uclass_find_next_device(&dev)) { + if (device_probe(dev)) + continue; + } + + arch_cpu_init(); + + board_early_init_f(); + + timer_init(); + + preloader_console_init(); + + puts("Normal Boot\n"); +} + +#if (IS_ENABLED(CONFIG_SPL_LOAD_FIT)) +int board_fit_config_name_match(const char *name) +{ + /* Just empty function now - can't decide what to choose */ + debug("%s: %s\n", __func__, name); + + return 0; +} +#endif + +void board_init_f(ulong dummy) +{ + /* Clear global data */ + memset((void *)gd, 0, sizeof(gd_t)); + + /* Clear the BSS. */ + memset(__bss_start, 0, __bss_end - __bss_start); + + board_init_r(NULL, 0); +} diff --git a/board/congatec/common/Kconfig b/board/congatec/common/Kconfig new file mode 100644 index 0000000000..5c205bd830 --- /dev/null +++ b/board/congatec/common/Kconfig @@ -0,0 +1,48 @@ +if !ARCH_IMX8M && !ARCH_IMX8 + +config CHAIN_OF_TRUST + depends on !FIT_SIGNATURE && SECURE_BOOT + imply CMD_BLOB + imply CMD_HASH if ARM + select FSL_CAAM + select SPL_BOARD_INIT if (ARM && SPL) + select SHA_HW_ACCEL + select SHA_PROG_HW_ACCEL + select ENV_IS_NOWHERE + select CMD_EXT4 if ARM + select CMD_EXT4_WRITE if ARM + bool + default y + +config CMD_ESBC_VALIDATE + bool "Enable the 'esbc_validate' and 'esbc_halt' commands" + default y if CHAIN_OF_TRUST + help + This option enables two commands used for secure booting: + + esbc_validate - validate signature using RSA verification + esbc_halt - put the core in spin loop (Secure Boot Only) + +endif + +config VOL_MONITOR_LTC3882_READ + depends on VID + bool "Enable the LTC3882 voltage monitor read" + default n + help + This option enables LTC3882 voltage monitor read + functionality. It is used by common VID driver. + +config VOL_MONITOR_LTC3882_SET + depends on VID + bool "Enable the LTC3882 voltage monitor set" + default n + help + This option enables LTC3882 voltage monitor set + functionality. It is used by common VID driver. + +config USB_TCPC + bool "USB Typec port controller simple driver" + default n + help + Enable USB type-c port controller (TCPC) driver diff --git a/board/congatec/common/Makefile b/board/congatec/common/Makefile new file mode 100644 index 0000000000..d4ddfbf971 --- /dev/null +++ b/board/congatec/common/Makefile @@ -0,0 +1,23 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +MINIMAL= + +ifdef CONFIG_SPL_BUILD +ifdef CONFIG_SPL_INIT_MINIMAL +MINIMAL=y +endif +endif + +ifdef MINIMAL +# necessary to create built-in.o +obj- := __dummy__.o +else + +obj-y += mmc.o + +endif diff --git a/board/congatec/common/mmc.c b/board/congatec/common/mmc.c new file mode 100644 index 0000000000..bd0277c2b6 --- /dev/null +++ b/board/congatec/common/mmc.c @@ -0,0 +1,50 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2016 Freescale Semiconductor, Inc. + * Copyright 2018 NXP + * + */ +#include <common.h> +#include <asm/arch/sys_proto.h> +#include <linux/errno.h> +#include <asm/io.h> +#include <env.h> +#include <command.h> +#include <stdbool.h> +#include <mmc.h> + +static int check_mmc_autodetect(void) +{ + char *autodetect_str = env_get("mmcautodetect"); + + if ((autodetect_str) && (strcmp(autodetect_str, "yes") == 0)) + return 1; + + return 0; +} + +/* This should be defined for each board */ +__weak int mmc_map_to_kernel_blk(int dev_no) +{ + return dev_no; +} + +void board_late_mmc_env_init(void) +{ + char cmd[32]; + char mmcblk[32]; + u32 dev_no = mmc_get_env_dev(); + + if (!check_mmc_autodetect()) + return; + + env_set_ulong("mmcdev", dev_no); + + /* Set mmcblk env */ + sprintf(mmcblk, "/dev/mmcblk%dp2 rootwait rw", + mmc_map_to_kernel_blk(dev_no)); + env_set("mmcroot", mmcblk); + + sprintf(cmd, "mmc dev %d", dev_no); + run_command(cmd, 0); +} diff --git a/configs/cgtqmx8_defconfig b/configs/cgtqmx8_defconfig new file mode 100644 index 0000000000..238e421601 --- /dev/null +++ b/configs/cgtqmx8_defconfig @@ -0,0 +1,86 @@ +CONFIG_ARM=y +CONFIG_SPL_SYS_ICACHE_OFF=y +CONFIG_SPL_SYS_DCACHE_OFF=y +CONFIG_ARCH_IMX8=y +CONFIG_SYS_TEXT_BASE=0x80020000 +CONFIG_SPL_GPIO_SUPPORT=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_TARGET_CONGA_QMX8=y +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=3 +CONFIG_SPL=y +CONFIG_FIT=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/congatec/cgtqmx8/imximage.cfg" +CONFIG_BOOTDELAY=3 +CONFIG_IMX_BOOTAUX=y +CONFIG_LOG=y +CONFIG_SPL_BOARD_INIT=y +CONFIG_HUSH_PARSER=y +CONFIG_SPL_SEPARATE_BSS=y +CONFIG_SPL_POWER_SUPPORT=y +CONFIG_SPL_POWER_DOMAIN=y +CONFIG_SPL_WATCHDOG_SUPPORT=y +CONFIG_CMD_CPU=y +# CONFIG_BOOTM_NETBSD is not set +# CONFIG_CMD_IMPORTENV is not set +CONFIG_CMD_CLK=y +CONFIG_CMD_DM=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FUSE=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="imx8qm-cgtqmx8" +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_SIZE=0x1000 +CONFIG_ENV_OFFSET=0x400000 +CONFIG_SPL_DM=y +CONFIG_SPL_CLK=y +CONFIG_CLK_IMX8=y +CONFIG_CPU=y +CONFIG_DM_GPIO=y +CONFIG_MXC_GPIO=y +CONFIG_DM_PCA953X=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_IMX_LPI2C=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y +CONFIG_MISC=y +CONFIG_DM_MMC=y +CONFIG_FSL_USDHC=y +CONFIG_PHYLIB=y +CONFIG_PHY_ADDR_ENABLE=y +CONFIG_PHY_ATHEROS=y +CONFIG_DM_ETH=y +CONFIG_PHY_GIGE=y +CONFIG_FEC_MXC_SHARE_MDIO=y +CONFIG_FEC_MXC_MDIO_BASE=0x5B040000 +CONFIG_FEC_MXC=y +CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_SPL_PINCTRL=y +CONFIG_PINCTRL_IMX8=y +CONFIG_POWER_DOMAIN=y +CONFIG_IMX8_POWER_DOMAIN=y +CONFIG_DM_REGULATOR=y +CONFIG_SPL_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_SPL_DM_REGULATOR_GPIO=y +CONFIG_DM_SERIAL=y +CONFIG_FSL_LPUART=y +CONFIG_SPL_TINY_MEMSET=y +# CONFIG_EFI_LOADER is not set +CONFIG_SYS_MMCSD_FS_BOOT_PARTITION=0 +CONFIG_SYS_MMC_ENV_PART=0 +CONFIG_SYS_MMC_ENV_DEV=1 diff --git a/doc/board/congatec/cgtqmx8.rst b/doc/board/congatec/cgtqmx8.rst new file mode 100644 index 0000000000..bccdef2f16 --- /dev/null +++ b/doc/board/congatec/cgtqmx8.rst @@ -0,0 +1,70 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +U-Boot for the Congatec conga-QMX8 board +======================================== + +Quick Start +----------- + +- Build the ARM Trusted firmware binary +- Get scfw_tcm.bin and ahab-container.img +- Get imx-mkimage +- Build U-Boot +- Build imx-mkimage +- Flash the binary into the SD card +- Boot + +Get and Build the ARM Trusted firmware +-------------------------------------- + +.. code-block:: bash + + $ git clone https://source.codeaurora.org/external/imx/imx-atf + $ cd imx-atf/ + $ git checkout origin/imx_4.14.78_1.0.0_ga -b imx_4.14.78_1.0.0_ga + $ make PLAT=imx8qm bl31 + +Get scfw_tcm.bin and ahab-container.img +--------------------------------------- + +.. code-block:: bash + + $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-sc-firmware-1.1.bin + $ chmod +x imx-sc-firmware-1.1.bin + $ ./imx-sc-firmware-1.1.bin + $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin + $ chmod +x firmware-imx-8.0.bin + $ ./firmware-imx-8.0.bin + +Or use this to avoid running random scripts from the internet, +but note that you must agree to the license the script displays: + +.. code-block:: bash + + $ dd if=imx-sc-firmware-1.1.bin of=imx-sc-firmware-1.1.tar.bz2 bs=37185 skip=1 + $ tar -xf imx-sc-firmware-1.1.tar.bz2 + $ cp imx-sc-firmware-1.1/mx8qx-val-scfw-tcm.bin $(builddir) + + $ dd if=firmware-imx-8.0.bin of=firmware-imx-8.0.tar.bz2 bs=37180 skip=1 + $ tar -xf firmware-imx-8.0.tar.bz2 + $ cp firmware-imx-8.0/firmware/seco/mx8qm-ahab-container.img $(builddir) + +Build U-Boot +------------ + +.. code-block:: bash + + $ export ATF_LOAD_ADDR=0x80000000 + $ export BL33_LOAD_ADDR=0x80020000 + $ make cgtqmx8_defconfig + $ make u-boot.bin + $ make flash.bin + +Flash the binary into the SD card +--------------------------------- + +Burn the flash.bin binary to SD card offset 32KB: + +.. code-block:: bash + + $ sudo dd if=flash.bin of=/dev/sd[x] bs=1k seek=32 conv=fsync diff --git a/doc/board/congatec/index.rst b/doc/board/congatec/index.rst new file mode 100644 index 0000000000..cc57b36b2e --- /dev/null +++ b/doc/board/congatec/index.rst @@ -0,0 +1,9 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Congatec +======== + +.. toctree:: + :maxdepth: 2 + + cgtqmx8.rst diff --git a/include/configs/cgtqmx8.h b/include/configs/cgtqmx8.h new file mode 100644 index 0000000000..15c50279ad --- /dev/null +++ b/include/configs/cgtqmx8.h @@ -0,0 +1,181 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2017-2018 NXP + * Copyright 2018 congatec AG + * + */ + +#ifndef __CGTQMX8_H +#define __CGTQMX8_H + +#include <linux/sizes.h> +#include <asm/arch/imx-regs.h> + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SPL_TEXT_BASE 0x0 +#define CONFIG_SPL_MAX_SIZE (124 * 1024) +#define CONFIG_SYS_MONITOR_LEN (1024 * 1024) +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x800 + +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" +#define CONFIG_SPL_STACK 0x013E000 +#define CONFIG_SPL_BSS_START_ADDR 0x00128000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x1000 /* 4 KB */ +#define CONFIG_SYS_SPL_MALLOC_START 0x00120000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x3000 /* 12 KB */ +#define CONFIG_SERIAL_LPUART_BASE 0x5a060000 +#define CONFIG_MALLOC_F_ADDR 0x00120000 + +#define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE + +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE + +#define CONFIG_OF_EMBED +#endif + +#define CONFIG_REMAKE_ELF + +#define CONFIG_BOARD_EARLY_INIT_F + +/* Flat Device Tree Definitions */ +#define CONFIG_OF_BOARD_SETUP + +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) +#define CONFIG_SYS_FSL_ESDHC_ADDR 0 +#define USDHC1_BASE_ADDR 0x5B010000 +#define USDHC2_BASE_ADDR 0x5B020000 +#define USDHC3_BASE_ADDR 0x5B030000 +#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */ + +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + +/* Boot M4 */ +#define M4_BOOT_ENV \ + "m4_0_image=m4_0.bin\0" \ + "m4_1_image=m4_1.bin\0" \ + "loadm4image_0=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4_0_image}\0" \ + "loadm4image_1=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4_1_image}\0" \ + "m4boot_0=run loadm4image_0; dcache flush; bootaux ${loadaddr} 0\0" \ + "m4boot_1=run loadm4image_1; dcache flush; bootaux ${loadaddr} 1\0" \ + +#ifdef CONFIG_NAND_BOOT +#define MFG_NAND_PARTITION "mtdparts=gpmi-nand:128m(boot),32m(kernel),16m(dtb),8m(misc),-(rootfs) " +#else +#define MFG_NAND_PARTITION "" +#endif +#define FEC0_RESET IMX_GPIO_NR(2, 5) +#define FEC0_PDOMAIN "conn_enet0" + +#define CONFIG_MFG_ENV_SETTINGS \ + "mfgtool_args=setenv bootargs console=${console},${baudrate} " \ + "rdinit=/linuxrc " \ + "g_mass_storage.stall=0 g_mass_storage.removable=1 " \ + "g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\ + "g_mass_storage.iSerialNumber=\"\" "\ + MFG_NAND_PARTITION \ + "clk_ignore_unused "\ + "\0" \ + "initrd_addr=0x83800000\0" \ + "bootcmd_mfg=run mfgtool_args;booti ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \ + +/* Initial environment variables */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_MFG_ENV_SETTINGS \ + M4_BOOT_ENV \ + "script=boot.scr\0" \ + "image=Image\0" \ + "panel=NULL\0" \ + "console=ttyLP0\0" \ + "fdt_addr=0x83000000\0" \ + "boot_fdt=try\0" \ + "fdt_file=imx8qm-cgt-qmx8.dtb\0" \ + "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \ + "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \ + "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \ + "mmcautodetect=yes\0" \ + "mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot} earlycon\0 " \ + "loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if run loadfdt; then " \ + "booti ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "else " \ + "echo wait for boot; " \ + "fi;\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp rw earlycon\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${loadaddr} ${image}; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ + "booti ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "else " \ + "booti; " \ + "fi;\0" + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loadimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else booti ${loadaddr} - ${fdt_addr}; fi" + +/* Link Definitions */ +#define CONFIG_LOADADDR 0x80280000 + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR + +#define CONFIG_SYS_INIT_SP_ADDR 0x80200000 + +#define CONFIG_SYS_MMC_IMG_LOAD_PART 1 + +#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2 */ +#define CONFIG_SYS_FSL_USDHC_NUM 3 + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (32 * 1024)) * 1024) + +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define PHYS_SDRAM_1 0x80000000 +#define PHYS_SDRAM_2 0x880000000 +#define PHYS_SDRAM_1_SIZE 0x80000000 /* 2 GB */ +#define PHYS_SDRAM_2_SIZE 0x100000000 /* 4 GB */ + +/* Serial */ +#define CONFIG_BAUDRATE 115200 + +/* Generic Timer Definitions */ +#define COUNTER_FREQUENCY 8000000 /* 8MHz */ + +/* Networking */ +#define CONFIG_FEC_MXC_PHYADDR -1 +#define CONFIG_FEC_XCV_TYPE RGMII +#define FEC_QUIRK_ENET_MAC + +#endif /* __CGTQMX8_H */ -- 2.17.1

4 5

[PATCH] sunxi: Bring back SD card as MMC device 0
by Andre Przywara 29 May '21

29 May '21

Commit 2243d19e5618 ("mmc: mmc-uclass: Use dev_seq() to read aliases node's index") now actually enforces U-Boot's device enumeration policy, where explicitly named devices come first, then any other non-named devices follow, without filling gaps. For quite a while we have had an "mmc1 = &mmc2;" alias in our sunxi-u-boot.dtsi, which now leads to the problem that the SD card (which was always mmc device 0) now gets to be number 2. I guess this breaks quite some boot scripts, and is confusing at least. Just add an explicit mmc0 alias in the very same file to fix this and restore the old behaviour. Signed-off-by: Andre Przywara <andre.przywara(a)arm.com> Reported-by: Samuel Holland <samuel(a)sholland.org> --- arch/arm/dts/sunxi-u-boot.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/dts/sunxi-u-boot.dtsi b/arch/arm/dts/sunxi-u-boot.dtsi index a4227a3c22d..06da009fa28 100644 --- a/arch/arm/dts/sunxi-u-boot.dtsi +++ b/arch/arm/dts/sunxi-u-boot.dtsi @@ -12,6 +12,7 @@ / { aliases { + mmc0 = &mmc0; mmc1 = &mmc2; }; -- 2.17.5

3 6

[PATCH] reset: stm32: Fix bank and offset computation
by Patrice Chotard 28 May '21

28 May '21

BITS_PER_LONG is used to represent register's size which is 32. But when compiled on arch64, BITS_PER_LONG is then equal to 64. Fix bank and offset computation to make it work on arch32 and arch64 and ensure that register's size is always equal to 32. Signed-off-by: Patrice Chotard <patrice.chotard(a)foss.st.com> Signed-off-by: Pankaj Dev <pankaj.dev(a)st.com> --- drivers/reset/stm32-reset.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/reset/stm32-reset.c b/drivers/reset/stm32-reset.c index daa2e47ebb..bbc6b135a9 100644 --- a/drivers/reset/stm32-reset.c +++ b/drivers/reset/stm32-reset.c @@ -40,8 +40,8 @@ static int stm32_reset_free(struct reset_ctl *reset_ctl) static int stm32_reset_assert(struct reset_ctl *reset_ctl) { struct stm32_reset_priv *priv = dev_get_priv(reset_ctl->dev); - int bank = (reset_ctl->id / BITS_PER_LONG) * 4; - int offset = reset_ctl->id % BITS_PER_LONG; + int bank = (reset_ctl->id / (sizeof(u32) * BITS_PER_BYTE)) * 4; + int offset = reset_ctl->id % (sizeof(u32) * BITS_PER_BYTE); dev_dbg(reset_ctl->dev, "reset id = %ld bank = %d offset = %d)\n", reset_ctl->id, bank, offset); @@ -61,8 +61,8 @@ static int stm32_reset_assert(struct reset_ctl *reset_ctl) static int stm32_reset_deassert(struct reset_ctl *reset_ctl) { struct stm32_reset_priv *priv = dev_get_priv(reset_ctl->dev); - int bank = (reset_ctl->id / BITS_PER_LONG) * 4; - int offset = reset_ctl->id % BITS_PER_LONG; + int bank = (reset_ctl->id / (sizeof(u32) * BITS_PER_BYTE)) * 4; + int offset = reset_ctl->id % (sizeof(u32) * BITS_PER_BYTE); dev_dbg(reset_ctl->dev, "reset id = %ld bank = %d offset = %d)\n", reset_ctl->id, bank, offset); -- 2.17.1

2 3

[PATCH v1 0/6] Provide support for mv88e6020 Marvell switch
by Lukasz Majewski 28 May '21

28 May '21

This patch set provides support for mv88e6020 switch. It is a dual chip device, with direct access to port register on SMI bus. However, PHYs are accessed indirectly. Lukasz Majewski (6): net: mv88e61xx: Add support for checking addressing mode net: mv88e61xx: Configure PHY ports to also pass packets between them net: mv88e61xx: Clear temporary structs before using them in get_phy_id() net: mv88e61xx: Directly access the switch chip net: mv88e61xx: Set proper offset when R0_LED/ADDR4 is set on bootstrap net: mv88e61xx: Reset switch PHYs when bootstrapped to !NO_CPU drivers/net/phy/mv88e61xx.c | 158 ++++++++++++++++++++++++++++++++---- 1 file changed, 142 insertions(+), 16 deletions(-) -- 2.20.1

2 13

[PATCH] dfu: dfu_mtd: remove the mtd_block_op error when mtd_lock is not supported
by Patrick Delaunay 28 May '21

28 May '21

Fix the result of DFU_OP_WRITE operation in mtd_block_op function when mtd_lock is not supported (-EOPNOTSUPP) to avoid DFU stack error on the DFU manifestation of the MTD device, when dfu_flush_medium_mtd is called. Without this patch, dfu-util failed on dfuERROR state at the end of the write operation on the alternate even if MTD write opeartion is correctly performed. $> dfu-util -a 3 -D test.bin .... DFU mode device DFU version 0110 Device returned transfer size 4096 Copying data from PC to DFU device .... Download [=========================] 100% 225469 bytes Download done. state(10) = dfuERROR, status(14) = Something went wrong, but the device does not know what it was Done! Fixes: 65f3fc18fc1e ("dfu_mtd: Add provision to unlock mtd device") Signed-off-by: Patrick Delaunay <patrick.delaunay(a)foss.st.com> --- drivers/dfu/dfu_mtd.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/dfu/dfu_mtd.c b/drivers/dfu/dfu_mtd.c index ca67585a7e..ec40b8f6bb 100644 --- a/drivers/dfu/dfu_mtd.c +++ b/drivers/dfu/dfu_mtd.c @@ -150,7 +150,9 @@ static int mtd_block_op(enum dfu_op op, struct dfu_entity *dfu, /* Write done, lock again */ debug("Locking the mtd device\n"); ret = mtd_lock(mtd, lock_ofs, lock_len); - if (ret && ret != -EOPNOTSUPP) + if (ret == -EOPNOTSUPP) + ret = 0; + else if (ret) printf("MTD device lock failed\n"); } return ret; -- 2.17.1

3 2