February 2021 - U-Boot

[GIT PULL] TI changes for v2021.04 rc2
by Lokesh Vutla 05 Feb '21

05 Feb '21

Hi Tom, Please find the PR for master branch targeted for v2021.04-rc2 release. Details about the PR are updated in the tag message. Gitlab build report: https://gitlab.denx.de/u-boot/custodians/u-boot-ti/-/pipelines/6214 The following changes since commit fdcb93e1709ab1a2ebb562455621617c29e2099c: Merge branch '2021-02-01-assorted-fixes' (2021-02-02 09:24:10 -0500) are available in the Git repository at: https://gitlab.denx.de/u-boot/custodians/u-boot-ti.git tags/ti-v2021.04-rc2 for you to fetch changes up to 6239cc8c4e8484d908afc555eb59441a16a58b53: arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot (2021-02-04 20:37:57 +0530) ---------------------------------------------------------------- - Sync DTS from Linux kernel for all K3 platforms - Add MMC higher speed nodes for AM65x, J721e, J7200 - Convert Nokia RX-51 to use CONFIG_DM_MMC - Minor fixes for LEGO MINDSTORMS ---------------------------------------------------------------- Aswath Govindraju (1): configs: am65x_evm_a53: Enable config for phandle check while getting sequence number Dario Binacchi (1): configs: am335x_evm: enable CONFIG_SPL_ALLOC_BD David Lechner (4): ARM: legoev3: set serial# env var ARM: legoev3: drop bi_arch_number configs: legoev3: disable CONFIG_NET configs: legoev3: disable non-Linux boot options Faiz Abbas (20): mmc: sdhci: Add helper functions for UHS modes mmc: am654_sdhci: Unconditionally switch off DLL in the beginning of ios_post() mmc: am654_sdhci: Convert flag fields to BIT macro mmc: am654_sdhci: Add flag for PHY calibration mmc: am654_sdhci: Add support for AM65x SR2.0 mmc: am654_sdhci: Add support for input tap delay mmc: am654_sdhci: Add support for writing to clkbuf_sel mmc: am654_sdhci: Add support for software tuning mmc: am654_sdhci: Fix HISPD bit configuration in some lower speed modes mmc: am654_sdhci: Use sdhci_set_control_reg() arm: dts: k3-am65: Fix mmc nodes arm: dts: k3-j721e-main: Update otap-delay values arm: dts: k3-j721e-common-proc-board: Add support for UHS modes for SD card arm: dts: k3-j7200-main: Add support for gpio0 arm: dts: k3-j7200-common-proc-board: Enable support for UHS modes configs: j721e_evm: Add support for UHS modes configs: j7200_evm: Add support for UHS modes arm: dts: k3-am65-main: Add itapdly and clkbuf-sel values arm: dts: k3-am654-base-board: Limit Sd card to High speed modes configs: am65x_evm: Add configs for UHS modes Lokesh Vutla (3): arm: dts: k3-am65: Sync Linux v5.11-rc6 dts into U-Boot arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot Pali Rohár (1): Nokia RX-51: Convert to CONFIG_DM_MMC Suman Anna (1): remoteproc: k3_r5: Sync to upstreamed kernel DT property names arch/arm/dts/k3-am65-main.dtsi | 823 +++++++-- arch/arm/dts/k3-am65-mcu.dtsi | 221 ++- arch/arm/dts/k3-am65-wakeup.dtsi | 48 +- arch/arm/dts/k3-am65.dtsi | 10 +- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 132 +- arch/arm/dts/k3-am654-base-board.dts | 449 ++++- arch/arm/dts/k3-am654-industrial-thermal.dtsi | 45 + arch/arm/dts/k3-am654-r5-base-board.dts | 58 +- arch/arm/dts/k3-am654.dtsi | 10 +- .../k3-j7200-common-proc-board-u-boot.dtsi | 16 +- arch/arm/dts/k3-j7200-common-proc-board.dts | 161 +- arch/arm/dts/k3-j7200-main.dtsi | 289 +++- arch/arm/dts/k3-j7200-mcu-wakeup.dtsi | 244 +-- .../arm/dts/k3-j7200-r5-common-proc-board.dts | 15 + arch/arm/dts/k3-j7200-som-p0.dtsi | 107 +- arch/arm/dts/k3-j7200.dtsi | 27 +- .../k3-j721e-common-proc-board-u-boot.dtsi | 70 +- arch/arm/dts/k3-j721e-common-proc-board.dts | 673 +++++++- arch/arm/dts/k3-j721e-main.dtsi | 1484 +++++++++++++++-- arch/arm/dts/k3-j721e-mcu-wakeup.dtsi | 234 ++- .../k3-j721e-r5-common-proc-board-u-boot.dtsi | 9 + .../arm/dts/k3-j721e-r5-common-proc-board.dts | 2 - arch/arm/dts/k3-j721e-som-p0.dtsi | 272 ++- arch/arm/dts/k3-j721e.dtsi | 29 +- board/lego/ev3/legoev3.c | 89 +- board/nokia/rx51/rx51.c | 33 +- configs/am335x_evm_defconfig | 1 + configs/am65x_evm_a53_defconfig | 9 + configs/am65x_evm_r5_defconfig | 2 + configs/j7200_evm_a72_defconfig | 8 + configs/j7200_evm_r5_defconfig | 1 + configs/j721e_evm_a72_defconfig | 8 + configs/j721e_evm_r5_defconfig | 1 + configs/legoev3_defconfig | 8 +- configs/nokia_rx51_defconfig | 6 + .../remoteproc/ti,k3-r5f-rproc.txt | 26 +- drivers/mmc/Kconfig | 1 + drivers/mmc/am654_sdhci.c | 384 +++-- drivers/mmc/sdhci.c | 95 ++ drivers/remoteproc/ti_k3_r5f_rproc.c | 8 +- include/configs/legoev3.h | 2 - include/dt-bindings/mux/ti-serdes.h | 93 ++ include/sdhci.h | 10 + 43 files changed, 5023 insertions(+), 1190 deletions(-) create mode 100644 arch/arm/dts/k3-am654-industrial-thermal.dtsi create mode 100644 include/dt-bindings/mux/ti-serdes.h -- 2.30.0

2 1

RE: [PATCH v4 5/5] board/km: add support for seli8 design based on nxp ls102x
by Aleksandar Gerasimovski 05 Feb '21

05 Feb '21

The SELI8 design is a new tdm service unit card for Hitachi-Powergrids XMC and FOX product lines. It is based on NXP LS1021 SoC and it provides following interfaces: - IFC interface for NOR, NAND and external FPGA's - 1 x RGMII ETH for debug purposes - 2 x SGMII ETH for management communication via back-plane - 1 x uQE HDLC for management communication via back-plane - 1 x I2C for peripheral devices - 1 x SPI for peripheral devices - 1 x UART for debug logging It is foreseen that the design will be later re-used for another XMC and FOX service cards with similar SoC requirements. Signed-off-by: Rainer Boschung <rainer.boschung(a)hitachi-powergrids.com> Signed-off-by: Matteo Ghidoni <matteo.ghidoni(a)hitachi-powergrids.com> Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski(a)hitachi-powergrids.com> --- Changes for v2: - fix patch subject to 60 characters Changes for v3: - remove obsolete CMDLINE_TAG Changes for v4: - rebase, include i2c deblocking from keymile/common.h - move Kconfig's from board.h to board defconfig - fix ENV_SIZE, it was typo or copy-paste error --- --- arch/arm/Kconfig | 19 ++ arch/arm/dts/Makefile | 2 + arch/arm/dts/ls1021a-pg-wcom-seli8.dts | 111 +++++++++ board/keymile/Kconfig | 23 +- board/keymile/common/ivm.c | 19 +- board/keymile/pg-wcom-ls102xa/Kconfig | 19 ++ board/keymile/pg-wcom-ls102xa/MAINTAINERS | 10 + board/keymile/pg-wcom-ls102xa/Makefile | 11 + board/keymile/pg-wcom-ls102xa/ddr.c | 90 +++++++ board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c | 160 +++++++++++++ configs/pg_wcom_seli8_defconfig | 65 ++++++ include/configs/km/pg-wcom-ls102xa.h | 297 ++++++++++++++++++++++++ include/configs/pg-wcom-seli8.h | 45 ++++ 13 files changed, 860 insertions(+), 11 deletions(-) create mode 100644 arch/arm/dts/ls1021a-pg-wcom-seli8.dts create mode 100644 board/keymile/pg-wcom-ls102xa/Kconfig create mode 100644 board/keymile/pg-wcom-ls102xa/MAINTAINERS create mode 100644 board/keymile/pg-wcom-ls102xa/Makefile create mode 100644 board/keymile/pg-wcom-ls102xa/ddr.c create mode 100644 board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c create mode 100644 configs/pg_wcom_seli8_defconfig create mode 100644 include/configs/km/pg-wcom-ls102xa.h create mode 100644 include/configs/pg-wcom-seli8.h diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 95557d6..729f1a3 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1517,6 +1517,24 @@ config TARGET_LS1021ATWR select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI imply SCSI +config TARGET_PG_WCOM_SELI8 + bool "Support Hitachi-Powergrids SELI8 service unit card" + select ARCH_LS1021A + select ARCH_SUPPORT_PSCI + select BOARD_EARLY_INIT_F + select BOARD_LATE_INIT + select CPU_V7A + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select SYS_FSL_DDR + select FSL_DDR_INTERACTIVE + select VENDOR_KM + imply SCSI + help + Support for Hitachi-Powergrids SELI8 service unit card. + SELI8 is a QorIQ LS1021a based service unit card used + in XMC20 and FOX615 product families. + config TARGET_LS1021ATSN bool "Support ls1021atsn" select ARCH_LS1021A @@ -2036,6 +2054,7 @@ source "board/variscite/dart_6ul/Kconfig" source "board/vscom/baltos/Kconfig" source "board/phytium/durian/Kconfig" source "board/xen/xenguest_arm64/Kconfig" +source "board/keymile/Kconfig" source "arch/arm/Kconfig.debug" diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 858b79a..dbc71c0 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -399,6 +399,8 @@ dtb-$(CONFIG_ARCH_LS1021A) += ls1021a-qds-duart.dtb \ ls1021a-qds-lpuart.dtb \ ls1021a-twr-duart.dtb ls1021a-twr-lpuart.dtb \ ls1021a-iot-duart.dtb ls1021a-tsn.dtb +dtb-$(CONFIG_TARGET_PG_WCOM_SELI8) += ls1021a-pg-wcom-seli8.dtb + dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \ fsl-ls2080a-qds-42-x.dtb \ fsl-ls2080a-rdb.dtb \ diff --git a/arch/arm/dts/ls1021a-pg-wcom-seli8.dts b/arch/arm/dts/ls1021a-pg-wcom-seli8.dts new file mode 100644 index 0000000..e335188 --- /dev/null +++ b/arch/arm/dts/ls1021a-pg-wcom-seli8.dts @@ -0,0 +1,111 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2013-2015 Freescale Semiconductor, Inc. + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +/dts-v1/; +#include "ls1021a.dtsi" + +/ { + model = "Hitachi-Powergrids SELI8 Service Unit for XMC and FOX"; + + chosen { + stdout-path = &uart0; + }; +}; + +&enet0 { + status = "okay"; + tbi-handle = <&tbi0>; + phy-connection-type = "sgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&enet1 { + status = "okay"; + tbi-handle = <&tbi1>; + phy-connection-type = "sgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&enet2 { + phy-handle = <&debug_phy>; + phy-connection-type = "rgmii-id"; + status = "okay"; +}; + +&i2c0 { + status = "okay"; +}; + +&ifc { + #address-cells = <2>; + #size-cells = <1>; + /* NOR Flash on board */ + ranges = <0x0 0x0 0x60000000 0x04000000>; + status = "okay"; + + nor@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x4000000>; + bank-width = <2>; + device-width = <1>; + + partition@0 { + label = "rcw"; + reg = <0x0 0x20000>; + read-only; + }; + partition@20000 { + label = "qe"; + reg = <0x20000 0x20000>; + }; + partition@40000 { + label = "envred"; + reg = <0x40000 0x20000>; + }; + partition@60000 { + label = "env"; + reg = <0x60000 0x20000>; + }; + partition@100000 { + label = "u-boot"; + reg = <0x100000 0x100000>; + }; + partition@200000 { + label = "ubi0"; + reg = <0x200000 0x3E00000>; + }; + }; +}; + +&mdio0 { + debug_phy: ethernet-phy@11 { + reg = <0x11>; + }; + + tbi0: tbi-phy@0xb { + reg = <0xb>; + device_type = "tbi-phy"; + }; +}; + +&mdio1 { + tbi1: tbi-phy@0xd { + reg = <0xd>; + device_type = "tbi-phy"; + }; +}; + +&uart0 { + status = "okay"; +}; diff --git a/board/keymile/Kconfig b/board/keymile/Kconfig index e590690..965a537 100644 --- a/board/keymile/Kconfig +++ b/board/keymile/Kconfig @@ -20,8 +20,8 @@ config KM_PNVRAM config KM_PHRAM hex "Physical RAM" - default 0x17F000 if ARM - default 0x100000 if PPC + default 0x17F000 if ARM && !ARCH_LS1021A + default 0x100000 if PPC || ARCH_LS1021A depends on !ARCH_SOCFPGA help Start address of the physical RAM, which is the mounted /var folder. @@ -30,13 +30,14 @@ config KM_RESERVED_PRAM hex "Reserved RAM" default 0x801000 if ARCH_KIRKWOOD default 0x0 if MPC83xx - default 0x1000 if MPC85xx + default 0x1000 if MPC85xx || ARCH_LS1021A depends on !ARCH_SOCFPGA help Reserved physical RAM area at the end of memory for special purposes. config KM_CRAMFS_ADDR hex "CRAMFS Address" + default 0x83000000 if ARCH_LS1021A default 0x3000000 depends on !ARCH_SOCFPGA help @@ -44,16 +45,25 @@ config KM_CRAMFS_ADDR config KM_KERNEL_ADDR hex "Kernel Load Address" + default 0x82000000 if ARCH_LS1021A default 0x2000000 help Address where to load Linux kernel in RAM. config KM_FDT_ADDR hex "FDT Load Address" + default 0x82FC0000 if ARCH_LS1021A default 0x2FC0000 help Address where to load flattened device tree in RAM. +config SYS_PAX_BASE + hex "PAX IFC Base Address" + default 0x78000000 + depends on ARCH_LS1021A + help + IFC Base Address for PAXx FPGA. + config KM_CONSOLE_TTY string "KM Console" default "ttyS0" @@ -69,9 +79,9 @@ config KM_DEF_NETDEV config KM_COMMON_ETH_INIT bool "Common Ethernet Initialization" default y if ARCH_KIRKWOOD || MPC83xx - default n if MPC85xx || ARCH_SOCFPGA + default n if MPC85xx || ARCH_SOCFPGA || ARCH_LS1021A help - Use the Ethernet initialization implemented in common code, which + Use the Ethernet initialization implemented in common code that detects if a Piggy board is present. config PIGGY_MAC_ADDRESS_OFFSET @@ -90,7 +100,7 @@ config KM_MVEXTSW_ADDR config KM_IVM_BUS int "IVM I2C Bus" default 0 if ARCH_SOCFPGA - default 1 if ARCH_KIRKWOOD || MPC85xx + default 1 if ARCH_KIRKWOOD || MPC85xx || ARCH_LS1021A default 2 if MPC83xx help Identifier number of I2C bus, where the inventory EEPROM is connected to. @@ -116,6 +126,7 @@ config SYS_IVM_EEPROM_PAGE_LEN source "board/keymile/km83xx/Kconfig" source "board/keymile/kmp204x/Kconfig" source "board/keymile/km_arm/Kconfig" +source "board/keymile/pg-wcom-ls102xa/Kconfig" endmenu diff --git a/board/keymile/common/ivm.c b/board/keymile/common/ivm.c index e989bf6..48817cb 100644 --- a/board/keymile/common/ivm.c +++ b/board/keymile/common/ivm.c @@ -306,11 +306,7 @@ static int ivm_populate_env(unsigned char *buf, int len, int mac_address_offset) return 0; page2 = &buf[CONFIG_SYS_IVM_EEPROM_PAGE_LEN * 2]; - if (!IS_ENABLED(CONFIG_KMTEGR1)) { - /* if an offset is defined, add it */ - process_mac(valbuf, page2, mac_address_offset, true); - env_set((char *)"ethaddr", (char *)valbuf); - } else { + if (IS_ENABLED(CONFIG_KMTEGR1)) { /* KMTEGR1 has a special setup. eth0 has no connection to the * outside and gets an locally administred MAC address, eth1 is * the debug interface and gets the official MAC address from @@ -320,6 +316,19 @@ static int ivm_populate_env(unsigned char *buf, int len, int mac_address_offset) env_set((char *)"ethaddr", (char *)valbuf); process_mac(valbuf, page2, mac_address_offset, true); env_set((char *)"eth1addr", (char *)valbuf); + } else if (IS_ENABLED(CONFIG_ARCH_LS1021A)) { + /* LS102xA has 1xRGMII for debug connection and + * 2xSGMII for back-plane mgmt connection + */ + process_mac(valbuf, page2, 1, true); + env_set((char *)"ethaddr", (char *)valbuf); + process_mac(valbuf, page2, 2, true); + env_set((char *)"eth1addr", (char *)valbuf); + process_mac(valbuf, page2, mac_address_offset, true); + env_set((char *)"eth2addr", (char *)valbuf); + } else { + process_mac(valbuf, page2, mac_address_offset, true); + env_set((char *)"ethaddr", (char *)valbuf); } return 0; diff --git a/board/keymile/pg-wcom-ls102xa/Kconfig b/board/keymile/pg-wcom-ls102xa/Kconfig new file mode 100644 index 0000000..15c009d --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/Kconfig @@ -0,0 +1,19 @@ +if TARGET_PG_WCOM_SELI8 + +config SYS_BOARD + default "pg-wcom-ls102xa" + +config SYS_VENDOR + default "keymile" + +config SYS_SOC + default "ls102xa" + +config SYS_CONFIG_NAME + default "pg-wcom-seli8" + +config BOARD_SPECIFIC_OPTIONS + def_bool y + imply FS_CRAMFS + +endif diff --git a/board/keymile/pg-wcom-ls102xa/MAINTAINERS b/board/keymile/pg-wcom-ls102xa/MAINTAINERS new file mode 100644 index 0000000..e1bc90a --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/MAINTAINERS @@ -0,0 +1,10 @@ +Hitachi Power Grids LS102XA BOARD +M: Aleksandar Gerasimovski <aleksandar.gerasimovski(a)hitachi-powergrids.com> +M: Rainer Boschung <rainer.boschung(a)hitachi-powergrids.com> +M: Matteo Ghidoni <matteo.ghidoni(a)hitachi-powergrids.com> +S: Maintained +F: board/keymile/pg-wcom-ls102xa/ +F: include/configs/km/pg-wcom-ls102xa.h +F: include/configs/pg-wcom-seli8.h +F: configs/pg_wcom_seli8_defconfig +F: arch/arm/dts/ls1021a-pg-wcom-seli8.dts diff --git a/board/keymile/pg-wcom-ls102xa/Makefile b/board/keymile/pg-wcom-ls102xa/Makefile new file mode 100644 index 0000000..229b0c2 --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/Makefile @@ -0,0 +1,11 @@ +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright 2021 Hitachi Power Grids. All rights reserved. +# + +obj-y += pg-wcom-ls102xa.o ddr.o +obj-y += ../common/common.o ../common/ivm.o ../common/qrio.o +obj-$(CONFIG_LAYERSCAPE_NS_ACCESS) += ../../freescale/common/ns_access.o +obj-$(CONFIG_LS102XA_STREAM_ID) += ../../freescale/common/ls102xa_stream_id.o +obj-$(CONFIG_ID_EEPROM) += ../../freescale/common/sys_eeprom.o diff --git a/board/keymile/pg-wcom-ls102xa/ddr.c b/board/keymile/pg-wcom-ls102xa/ddr.c new file mode 100644 index 0000000..6023573 --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/ddr.c @@ -0,0 +1,90 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +#include <common.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> +#include <asm/io.h> +#include <asm/arch/clock.h> +#include <asm/arch/ls102xa_soc.h> + +DECLARE_GLOBAL_DATA_PTR; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + if (ctrl_num > 1) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + + // 1/2 DRAM cycle (should be increased in case of ADDR/CMD heavily loaded than the clock) + popts->clk_adjust = 0x4; + popts->write_data_delay = 0x4; + // wr leveling start value for lane 0 + popts->wrlvl_start = 0x5; + // wr leveling start values for lanes 1-3 (lane 4 not there) + popts->wrlvl_ctl_2 = 0x05050500; + // 32-bit DRAM, no need to set start values for lanes we do not have (5-8) + popts->wrlvl_ctl_3 = 0x0; + popts->cpo_override = 0x1f; + + /* force DDR bus width to 32 bits */ + popts->data_bus_width = 1; + popts->otf_burst_chop_en = 0; + popts->burst_length = DDR_BL8; + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 1; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * Rtt and Rtt_WR override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + popts->cswl_override = DDR_CSWL_CS0; + + /* optimize cpo for erratum A-009942 */ + popts->cpo_sample = 0x58; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); +} + +int fsl_initdram(void) +{ + phys_size_t dram_size; + + puts("Initializing DDR....using SPD\n"); + dram_size = fsl_ddr_sdram(); + + erratum_a008850_post(); + + gd->ram_size = dram_size; + + return 0; +} + +int dram_init_banksize(void) +{ + gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; + gd->bd->bi_dram[0].size = gd->ram_size; + + return 0; +} diff --git a/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c b/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c new file mode 100644 index 0000000..6b0e963 --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c @@ -0,0 +1,160 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +#include <common.h> +#include <i2c.h> +#include <asm/io.h> +#include <asm/arch/immap_ls102xa.h> +#include <asm/arch/clock.h> +#include <asm/arch/fsl_serdes.h> +#include <asm/arch/ls102xa_devdis.h> +#include <asm/arch/ls102xa_soc.h> +#include <hwconfig.h> +#include <mmc.h> +#include <fsl_csu.h> +#include <fsl_esdhc.h> +#include <fsl_ifc.h> +#include <fsl_immap.h> +#include <netdev.h> +#include <fsl_mdio.h> +#include <tsec.h> +#include <fsl_sec.h> +#include <fsl_devdis.h> +#include <fsl_ddr.h> +#include <spl.h> +#include <fdt_support.h> +#include <fsl_qe.h> +#include <fsl_validate.h> + +#include "../common/common.h" +#include "../common/qrio.h" + +DECLARE_GLOBAL_DATA_PTR; + +static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN]; + +int checkboard(void) +{ + show_qrio(); + + return 0; +} + +int dram_init(void) +{ + return fsl_initdram(); +} + +int board_early_init_f(void) +{ + struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR; + struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR; + struct fsl_ifc ifc = {(void *)CONFIG_SYS_IFC_ADDR, (void *)NULL}; + + /* Disable unused MCK1 */ + setbits_be32(&gur->ddrclkdr, 2); + + /* IFC Global Configuration */ + setbits_be32(&ifc.gregs->ifc_gcr, 12 << IFC_GCR_TBCTL_TRN_TIME_SHIFT); + setbits_be32(&ifc.gregs->ifc_ccr, IFC_CCR_CLK_DIV(3) | + IFC_CCR_INV_CLK_EN); + + /* clear BD & FR bits for BE BD's and frame data */ + clrbits_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR); + out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125); + + init_early_memctl_regs(); + + /* QRIO Configuration */ + qrio_uprstreq(UPREQ_CORE_RST); + + if (IS_ENABLED(CONFIG_TARGET_PG_WCOM_SELI8)) { + qrio_prstcfg(KM_LIU_RST, PRSTCFG_POWUP_UNIT_RST); + qrio_wdmask(KM_LIU_RST, true); + + qrio_prstcfg(KM_PAXK_RST, PRSTCFG_POWUP_UNIT_RST); + qrio_wdmask(KM_PAXK_RST, true); + + qrio_prstcfg(KM_DBG_ETH_RST, PRSTCFG_POWUP_UNIT_CORE_RST); + qrio_prst(KM_DBG_ETH_RST, false, false); + } + + i2c_deblock_gpio_cfg(); + + arch_soc_init(); + + return 0; +} + +int board_init(void) +{ + if (IS_ENABLED(CONFIG_SYS_FSL_ERRATUM_A010315)) + erratum_a010315(); + + fsl_serdes_init(); + + ls102xa_smmu_stream_id_init(); + + u_qe_init(); + + return 0; +} + +int board_late_init(void) +{ + return 0; +} + +int misc_init_r(void) +{ + if (IS_ENABLED(CONFIG_FSL_DEVICE_DISABLE)) + device_disable(devdis_tbl, ARRAY_SIZE(devdis_tbl)); + + ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN, + CONFIG_PIGGY_MAC_ADDRESS_OFFSET); + + return 0; +} + +int ft_board_setup(void *blob, struct bd_info *bd) +{ + ft_cpu_setup(blob, bd); + + if (IS_ENABLED(CONFIG_PCI)) + ft_pci_setup(blob, bd); + + return 0; +} + +u8 flash_read8(void *addr) +{ + return __raw_readb(addr + 1); +} + +void flash_write16(u16 val, void *addr) +{ + u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00)); + + __raw_writew(shftval, addr); +} + +u16 flash_read16(void *addr) +{ + u16 val = __raw_readw(addr); + + return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00); +} + +int hush_init_var(void) +{ + ivm_analyze_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN); + return 0; +} + +int last_stage_init(void) +{ + set_km_env(); + return 0; +} diff --git a/configs/pg_wcom_seli8_defconfig b/configs/pg_wcom_seli8_defconfig new file mode 100644 index 0000000..60eb0e1 --- /dev/null +++ b/configs/pg_wcom_seli8_defconfig @@ -0,0 +1,65 @@ +CONFIG_ARM=y +CONFIG_TARGET_PG_WCOM_SELI8=y +CONFIG_SYS_TEXT_BASE=0x60100000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_KM_DEF_NETDEV="eth2" +CONFIG_KM_COMMON_ETH_INIT=y +CONFIG_PIGGY_MAC_ADDRESS_OFFSET=3 +CONFIG_SYS_MEMTEST_START=0x80000000 +CONFIG_SYS_MEMTEST_END=0x9fffffff +CONFIG_ENV_SIZE=0x20000 +CONFIG_ENV_SECT_SIZE=0x20000 +CONFIG_BOOTCOUNT_BOOTLIMIT=3 +CONFIG_SYS_BOOTCOUNT_ADDR=0x70000020 +CONFIG_DEFAULT_DEVICE_TREE="ls1021a-pg-wcom-seli8" +CONFIG_AHCI=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_BOOTDELAY=3 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0" +CONFIG_SILENT_CONSOLE=y +CONFIG_MISC_INIT_R=y +CONFIG_LAST_STAGE_INIT=y +CONFIG_CMD_IMLS=y +CONFIG_CMD_GREPENV=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_NAND=y +CONFIG_CMD_NAND_TRIMFFS=y +CONFIG_CMD_CRAMFS=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nor0=60000000.nor,nand0=68000000.flash" +CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:128k(rcw),128k(qe),128k(envred),128k(env),512k(res),1m(u-boot),-(ubi0);68000000.flash:-(ubi1)" +CONFIG_CMD_UBI=y +CONFIG_OF_CONTROL=y +CONFIG_ENV_IS_IN_FLASH=y +CONFIG_ENV_ADDR=0x60060000 +CONFIG_ENV_ADDR_REDUND=0x60040000 +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y +CONFIG_DM=y +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_SYS_FSL_DDR3=y +# CONFIG_MMC is not set +CONFIG_MTD=y +CONFIG_MTD_NOR_FLASH=y +CONFIG_FLASH_CFI_DRIVER=y +CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y +CONFIG_FLASH_CFI_MTD=y +CONFIG_SYS_FLASH_CFI=y +CONFIG_MTD_RAW_NAND=y +CONFIG_PHY_MARVELL=y +CONFIG_PHY_FIXED=y +CONFIG_DM_ETH=y +CONFIG_DM_MDIO=y +CONFIG_PHY_GIGE=y +CONFIG_MII=y +CONFIG_TSEC_ENET=y +CONFIG_SPECIFY_CONSOLE_INDEX=y +CONFIG_DM_SERIAL=y +CONFIG_SYS_NS16550=y diff --git a/include/configs/km/pg-wcom-ls102xa.h b/include/configs/km/pg-wcom-ls102xa.h new file mode 100644 index 0000000..e0f015e --- /dev/null +++ b/include/configs/km/pg-wcom-ls102xa.h @@ -0,0 +1,297 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +#ifndef __CONFIG_PG_WCOM_LS102XA_H +#define __CONFIG_PG_WCOM_LS102XA_H + +#define CONFIG_SYS_FSL_CLK + +#define CONFIG_SKIP_LOWLEVEL_INIT + +/* include common defines/options for all Keymile boards */ +#include "keymile-common.h" + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024) + +#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE + +#define CONFIG_SYS_CLK_FREQ 66666666 +/* + * Take into account default implementation where DDR_FDBK_MULTI is consider as + * configured for DDR_PLL = 2*MEM_PLL_RAT. + * In our case DDR_FDBK_MULTI is 2, means DDR_PLL = MEM_PLL_RAT. + */ +#define CONFIG_DDR_CLK_FREQ (100000000 >> 1) + +#define PHYS_SDRAM 0x80000000 +#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 4 + +#define CONFIG_DDR_SPD + +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x54 + +/* + * IFC Definitions + */ +/* NOR Flash Definitions */ +#define CONFIG_FSL_IFC +#define CONFIG_SYS_FLASH_BASE 0x60000000 +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE + +#define CONFIG_SYS_NOR0_CSPR_EXT (0x0) +#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_TE | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(64 * 1024 * 1024) + +#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_AVD_TGL_PGM_EN | \ + CSOR_NOR_ADM_SHIFT(0x4) | \ + CSOR_NOR_NOR_MODE_AYSNC_NOR | \ + CSOR_NOR_TRHZ_20 | \ + CSOR_NOR_BCTLD) +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x1) | \ + FTIM0_NOR_TEADC(0x7) | \ + FTIM0_NOR_TAVDS(0x0) | \ + FTIM0_NOR_TEAHC(0x1)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1) | \ + FTIM1_NOR_TRAD_NOR(0x21) | \ + FTIM1_NOR_TSEQRAD_NOR(0x21)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x1) | \ + FTIM2_NOR_TCH(0x1) | \ + FTIM2_NOR_TWPH(0x6) | \ + FTIM2_NOR_TWP(0xb)) +#define CONFIG_SYS_NOR_FTIM3 0 + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS } + +#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS +#define CONFIG_SYS_WRITE_SWAPPED_DATA + +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 + +/* NAND Flash Definitions */ +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_BASE 0x68000000 +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE + +#define CONFIG_SYS_NAND_CSPR_EXT (0x0) +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE) | \ + CSPR_PORT_SIZE_8 | \ + CSPR_TE | \ + CSPR_MSEL_NAND | \ + CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN \ + | CSOR_NAND_ECC_DEC_EN \ + | CSOR_NAND_ECC_MODE_4 \ + | CSOR_NAND_RAL_3 \ + | CSOR_NAND_PGS_2K \ + | CSOR_NAND_SPRZ_64 \ + | CSOR_NAND_PB(64) \ + | CSOR_NAND_TRHZ_40 \ + | CSOR_NAND_BCTLD) + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x3) | \ + FTIM0_NAND_TWP(0x8) | \ + FTIM0_NAND_TWCHT(0x3) | \ + FTIM0_NAND_TWH(0x5)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x1e) | \ + FTIM1_NAND_TWBE(0x1e) | \ + FTIM1_NAND_TRR(0x6) | \ + FTIM1_NAND_TRP(0x8)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x9) | \ + FTIM2_NAND_TREH(0x5) | \ + FTIM2_NAND_TWHRE(0x3c)) +#define CONFIG_SYS_NAND_FTIM3 (FTIM3_NAND_TWW(0x1e)) + +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 + +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +/* QRIO FPGA Definitions */ +#define CONFIG_SYS_QRIO_BASE 0x70000000 +#define CONFIG_SYS_QRIO_BASE_PHYS CONFIG_SYS_QRIO_BASE + +#define CONFIG_SYS_CSPR2_EXT (0x00) +#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE) | \ + CSPR_PORT_SIZE_8 | \ + CSPR_TE | \ + CSPR_MSEL_GPCM | \ + CSPR_V) +#define CONFIG_SYS_AMASK2 IFC_AMASK(64 * 1024) +#define CONFIG_SYS_CSOR2 (CSOR_GPCM_ADM_SHIFT(0x4) | \ + CSOR_GPCM_TRHZ_20 | \ + CSOR_GPCM_BCTLD) +#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x2) | \ + FTIM0_GPCM_TEADC(0x8) | \ + FTIM0_GPCM_TEAHC(0x2)) +#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x2) | \ + FTIM1_GPCM_TRAD(0x6)) +#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x1) | \ + FTIM2_GPCM_TCH(0x1) | \ + FTIM2_GPCM_TWP(0x7)) +#define CONFIG_SYS_CS2_FTIM3 0x04000000 + +/* + * Serial Port + */ +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + +/* + * I2C + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_INIT_BOARD +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ +#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ +#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ + +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_MAX_HOPS 1 +#define CONFIG_SYS_NUM_I2C_BUSES 3 +#define I2C_MUX_PCA_ADDR 0x70 +#define I2C_MUX_CH_DEFAULT 0x0 +#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \ + {1, {I2C_NULL_HOP} }, \ + } + +/* + * eTSEC + */ +#ifdef CONFIG_TSEC_ENET +#define CONFIG_ETHPRIME "ethernet@2d90000" +#endif + +#define CONFIG_LAYERSCAPE_NS_ACCESS +#define CONFIG_SMP_PEN_ADDR 0x01ee0200 +#define COUNTER_FREQUENCY 12500000 + +#define CONFIG_HWCONFIG +#define HWCONFIG_BUFFER_SIZE 256 +#define CONFIG_FSL_DEVICE_DISABLE + +/* + * Miscellaneous configurable options + */ + +#define CONFIG_SYS_LOAD_ADDR 0x82000000 + +#define CONFIG_LS102XA_STREAM_ID + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_LEN 0x100000 /* 1Mbyte */ +#define CONFIG_SYS_QE_FW_ADDR 0x60020000 + +#define CONFIG_SYS_BOOTCOUNT_BE + +/* + * Environment + */ + +#define CONFIG_ENV_TOTAL_SIZE 0x40000 +#define ENV_DEL_ADDR 0x60040000 /* direct for newenv */ + +#define CONFIG_ENV_OVERWRITE +#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ +#define CONFIG_KM_DEF_ENV +#endif + +#ifndef CONFIG_KM_DEF_BOOT_ARGS_CPU +#define CONFIG_KM_DEF_BOOT_ARGS_CPU "" +#endif + +#define CONFIG_KM_DEF_ENV_CPU \ + "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \ + "cramfsloadfdt=" \ + "cramfsload ${fdt_addr_r} " \ + "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \ + "u-boot=" CONFIG_HOSTNAME "/u-boot.bin\0" \ + "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize} && " \ + "erase " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize} && " \ + "cp.b ${load_addr_r} " \ + __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize} && " \ + "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize}\0" \ + "update-nor=protect off " __stringify(CONFIG_SYS_FLASH_BASE) \ + " +${filesize} && " \ + "erase " __stringify(CONFIG_SYS_FLASH_BASE) \ + " +${filesize} && " \ + "cp.b ${load_addr_r} " \ + __stringify(CONFIG_SYS_FLASH_BASE) " ${filesize} && " \ + "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +" __stringify(CONFIG_SYS_MONITOR_LEN)"\0" \ + "set_fdthigh=true\0" \ + "checkfdt=true\0" \ + "" + +#define CONFIG_KM_NEW_ENV \ + "newenv=protect off " __stringify(ENV_DEL_ADDR) \ + " +" __stringify(CONFIG_ENV_TOTAL_SIZE) " && " \ + "erase " __stringify(ENV_DEL_ADDR) \ + " +" __stringify(CONFIG_ENV_TOTAL_SIZE) " && " \ + "protect on " __stringify(ENV_DEL_ADDR) \ + " +" __stringify(CONFIG_ENV_TOTAL_SIZE) "\0" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_KM_NEW_ENV \ + CONFIG_KM_DEF_ENV \ + "EEprom_ivm=pca9547:70:9\0" \ + "" + +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Increase map for Linux */ + +#endif diff --git a/include/configs/pg-wcom-seli8.h b/include/configs/pg-wcom-seli8.h new file mode 100644 index 0000000..9a7669c --- /dev/null +++ b/include/configs/pg-wcom-seli8.h @@ -0,0 +1,45 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +#ifndef __CONFIG_PG_WCOM_SELI8_H +#define __CONFIG_PG_WCOM_SELI8_H + +#define CONFIG_HOSTNAME "SELI8" + +#define CONFIG_KM_UBI_PARTITION_NAME_BOOT "ubi0" +#define CONFIG_KM_UBI_PARTITION_NAME_APP "ubi1" + +/* PAXK FPGA Definitions */ +#define CONFIG_SYS_CSPR3_EXT (0x00) +#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(CONFIG_SYS_PAX_BASE) | \ + CSPR_PORT_SIZE_8 | \ + CSPR_MSEL_GPCM | \ + CSPR_V) +#define CONFIG_SYS_AMASK3 IFC_AMASK(64 * 1024) +#define CONFIG_SYS_CSOR3 (CSOR_GPCM_ADM_SHIFT(0x4) | \ + CSOR_GPCM_TRHZ_40) +#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x6) | \ + FTIM0_GPCM_TEADC(0x7) | \ + FTIM0_GPCM_TEAHC(0x2)) +#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x2) | \ + FTIM1_GPCM_TRAD(0x12)) +#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x3) | \ + FTIM2_GPCM_TCH(0x1) | \ + FTIM2_GPCM_TWP(0x12)) +#define CONFIG_SYS_CS3_FTIM3 0x04000000 + +/* PRST */ +#define KM_LIU_RST 0 +#define KM_PAXK_RST 1 +#define KM_DBG_ETH_RST 15 + +/* QRIO GPIOs used for deblocking */ +#define KM_I2C_DEBLOCK_PORT QRIO_GPIO_A +#define KM_I2C_DEBLOCK_SCL 20 +#define KM_I2C_DEBLOCK_SDA 21 + +#include "km/pg-wcom-ls102xa.h" + +#endif /* __CONFIG_PG_WCOM_SELI8_H */ -- 1.8.3.1 -----Original Message----- From: Tom Rini <trini(a)konsulko.com> Sent: Donnerstag, 4. Februar 2021 19:10 To: Aleksandar Gerasimovski <aleksandar.gerasimovski(a)hitachi-powergrids.com> Cc: Priyanka Jain (OSS) <priyanka.jain(a)oss.nxp.com>; Priyanka Jain <priyanka.jain(a)nxp.com>; u-boot(a)lists.denx.de; Valentin Longchamp <valentin.longchamp(a)hitachi-powergrids.com>; Holger Brunck <holger.brunck(a)hitachi-powergrids.com>; Rainer Boschung <rainer.boschung(a)hitachi-powergrids.com>; Matteo Ghidoni <matteo.ghidoni(a)hitachi-powergrids.com> Subject: Re: [PATCH v3 4/4] board/km: add support for seli8 design based on nxp ls102x On Thu, Feb 04, 2021 at 03:28:59PM +0000, Aleksandar Gerasimovski wrote: > The SELI8 design is a new tdm service unit card for Hitachi-Powergrids > XMC and FOX product lines. > > It is based on NXP LS1021 SoC and it provides following interfaces: > - IFC interface for NOR, NAND and external FPGA's > - 1 x RGMII ETH for debug purposes > - 2 x SGMII ETH for management communication via back-plane > - 1 x uQE HDLC for management communication via back-plane > - 1 x I2C for peripheral devices > - 1 x SPI for peripheral devices > - 1 x UART for debug logging > > It is foreseen that the design will be later re-used for another XMC > and FOX service cards with similar SoC requirements. > > Signed-off-by: Rainer Boschung > <rainer.boschung(a)hitachi-powergrids.com> > Signed-off-by: Matteo Ghidoni <matteo.ghidoni(a)hitachi-powergrids.com> > Signed-off-by: Aleksandar Gerasimovski > <aleksandar.gerasimovski(a)hitachi-powergrids.com> [snip] > +#ifndef __ASSEMBLY__ > +void set_sda(int state); > +void set_scl(int state); > +int get_sda(void); > +int get_scl(void); > +#endif As a pre-req clean-up, please put these in a proper header file under board/keymile/common/ and #include as needed and not in the per-board config.h files. [snip] > +/* > + * Environment > + */ > + > +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT > +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) Environment is handled via Kconfig, please correct this and audit the config.h file for other things that are handled via Kconfig now. Thanks! -- Tom

2 1

[PATCH 4/5] board/km: move km i2c deblock declarations to a km/common.h
by Aleksandar Gerasimovski 05 Feb '21

05 Feb '21

Cleanup, move the declarations to keymile/common.h instead declaring them per-board config.h Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski(a)hitachi-powergrids.com> --- board/keymile/common/common.h | 5 +++++ include/configs/km/km_arm.h | 4 ---- include/configs/kmp204x.h | 6 ------ 3 files changed, 5 insertions(+), 10 deletions(-) diff --git a/board/keymile/common/common.h b/board/keymile/common/common.h index 8251de4..15a3c37 100644 --- a/board/keymile/common/common.h +++ b/board/keymile/common/common.h @@ -136,6 +136,11 @@ int set_km_env(void); #define DELAY_ABORT_SEQ 62 /* @200kHz 9 clocks = 44us, 62us is ok */ #define DELAY_HALF_PERIOD (500 / (CONFIG_SYS_I2C_SPEED / 1000)) +void set_sda(int state); +void set_scl(int state); +int get_sda(void); +int get_scl(void); + int i2c_soft_read_pin(void); int i2c_make_abort(void); #endif /* __KEYMILE_COMMON_H */ diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h index 29060fa..4115906 100644 --- a/include/configs/km/km_arm.h +++ b/include/configs/km/km_arm.h @@ -110,10 +110,6 @@ #include <linux/delay.h> #include <linux/stringify.h> extern void __set_direction(unsigned pin, int high); -void set_sda(int state); -void set_scl(int state); -int get_sda(void); -int get_scl(void); #define KM_KIRKWOOD_SDA_PIN 8 #define KM_KIRKWOOD_SCL_PIN 9 #define KM_KIRKWOOD_SOFT_I2C_GPIOS 0x0300 diff --git a/include/configs/kmp204x.h b/include/configs/kmp204x.h index d1eb7b5..90e3702 100644 --- a/include/configs/kmp204x.h +++ b/include/configs/kmp204x.h @@ -237,12 +237,6 @@ unsigned long get_board_sys_clk(unsigned long dummy); {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \ {0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \ } -#ifndef __ASSEMBLY__ -void set_sda(int state); -void set_scl(int state); -int get_sda(void); -int get_scl(void); -#endif #define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/ -- 1.8.3.1

2 1

[PATCH] mmc: fsl_esdhc_imx: use VENDORSPEC_FRC_SDCLK_ON to control card clock output
by haibo.chen＠nxp.com 05 Feb '21

05 Feb '21

From: Haibo Chen <haibo.chen(a)nxp.com> For FSL_USDHC, it do not implement VENDORSPEC_CKEN/PEREN/HCKEN/IPGEN, these are reserved bits. Instead, use VENDORSPEC_FRC_SDCLK_ON to gate on/off the card clock output. After commit b5874b552ffa ("mmc: fsl_esdhc_imx: add wait_dat0() support"), we meet SD3.0 card can't work at UHS mode, mmc_switch_voltage() fail because the second mmc_wait_dat0 return -ETIMEDOUT. According to SD spec, during voltage switch, need to gate off/on the card clock. If not set the FRC_SDCLK_ON, after CMD11, hardware will gate off the card clock automatically, so card do not detect the clock off/on behavior, so will draw the data0 line low until next command. Fixes: b5874b552ffa ("mmc: fsl_esdhc_imx: add wait_dat0() support") Signed-off-by: Haibo Chen <haibo.chen(a)nxp.com> --- drivers/mmc/fsl_esdhc_imx.c | 29 +++++++++++++++++++++-------- include/fsl_esdhc_imx.h | 2 ++ 2 files changed, 23 insertions(+), 8 deletions(-) diff --git a/drivers/mmc/fsl_esdhc_imx.c b/drivers/mmc/fsl_esdhc_imx.c index 8ac859797f..da33ee8253 100644 --- a/drivers/mmc/fsl_esdhc_imx.c +++ b/drivers/mmc/fsl_esdhc_imx.c @@ -653,7 +653,10 @@ static void set_sysctl(struct fsl_esdhc_priv *priv, struct mmc *mmc, uint clock) clk = (pre_div << 8) | (div << 4); #ifdef CONFIG_FSL_USDHC - esdhc_clrbits32(&regs->vendorspec, VENDORSPEC_CKEN); + esdhc_clrbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON); + ret = readx_poll_timeout(esdhc_read32, &regs->prsstat, tmp, tmp & PRSSTAT_SDOFF, 100); + if (ret) + pr_warn("fsl_esdhc_imx: Internal clock never gate off.\n"); #else esdhc_clrbits32(&regs->sysctl, SYSCTL_CKEN); #endif @@ -665,7 +668,7 @@ static void set_sysctl(struct fsl_esdhc_priv *priv, struct mmc *mmc, uint clock) pr_warn("fsl_esdhc_imx: Internal clock never stabilised.\n"); #ifdef CONFIG_FSL_USDHC - esdhc_setbits32(&regs->vendorspec, VENDORSPEC_PEREN | VENDORSPEC_CKEN); + esdhc_setbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON); #else esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_CKEN); #endif @@ -720,8 +723,14 @@ static void esdhc_set_strobe_dll(struct mmc *mmc) struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev); struct fsl_esdhc *regs = priv->esdhc_regs; u32 val; + u32 tmp; + int ret; if (priv->clock > ESDHC_STROBE_DLL_CLK_FREQ) { + esdhc_clrbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON); + ret = readx_poll_timeout(esdhc_read32, &regs->prsstat, tmp, tmp & PRSSTAT_SDOFF, 100); + if (ret) + pr_warn("fsl_esdhc_imx: Internal clock never gate off.\n"); esdhc_write32(&regs->strobe_dllctrl, ESDHC_STROBE_DLL_CTRL_RESET); /* @@ -739,6 +748,7 @@ static void esdhc_set_strobe_dll(struct mmc *mmc) pr_warn("HS400 strobe DLL status REF not lock!\n"); if (!(val & ESDHC_STROBE_DLL_STS_SLV_LOCK)) pr_warn("HS400 strobe DLL status SLV not lock!\n"); + esdhc_setbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON); } } @@ -962,14 +972,18 @@ static int esdhc_set_ios_common(struct fsl_esdhc_priv *priv, struct mmc *mmc) #ifdef MMC_SUPPORTS_TUNING if (mmc->clk_disable) { #ifdef CONFIG_FSL_USDHC - esdhc_clrbits32(&regs->vendorspec, VENDORSPEC_CKEN); + u32 tmp; + + esdhc_clrbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON); + ret = readx_poll_timeout(esdhc_read32, &regs->prsstat, tmp, tmp & PRSSTAT_SDOFF, 100); + if (ret) + pr_warn("fsl_esdhc_imx: Internal clock never gate off.\n"); #else esdhc_clrbits32(&regs->sysctl, SYSCTL_CKEN); #endif } else { #ifdef CONFIG_FSL_USDHC - esdhc_setbits32(&regs->vendorspec, VENDORSPEC_PEREN | - VENDORSPEC_CKEN); + esdhc_setbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON); #else esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_CKEN); #endif @@ -1045,7 +1059,7 @@ static int esdhc_init_common(struct fsl_esdhc_priv *priv, struct mmc *mmc) #ifndef CONFIG_FSL_USDHC esdhc_setbits32(&regs->sysctl, SYSCTL_HCKEN | SYSCTL_IPGEN); #else - esdhc_setbits32(&regs->vendorspec, VENDORSPEC_HCKEN | VENDORSPEC_IPGEN); + esdhc_setbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON); #endif /* Set the initial clock speed */ @@ -1183,8 +1197,7 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv, esdhc_write32(&regs->autoc12err, 0); esdhc_write32(&regs->clktunectrlstatus, 0); #else - esdhc_setbits32(&regs->vendorspec, VENDORSPEC_PEREN | - VENDORSPEC_HCKEN | VENDORSPEC_IPGEN | VENDORSPEC_CKEN); + esdhc_setbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON); #endif if (priv->vs18_enable) diff --git a/include/fsl_esdhc_imx.h b/include/fsl_esdhc_imx.h index 45ed635a77..b092034464 100644 --- a/include/fsl_esdhc_imx.h +++ b/include/fsl_esdhc_imx.h @@ -39,6 +39,7 @@ #define VENDORSPEC_HCKEN 0x00001000 #define VENDORSPEC_IPGEN 0x00000800 #define VENDORSPEC_INIT 0x20007809 +#define VENDORSPEC_FRC_SDCLK_ON 0x00000100 #define IRQSTAT 0x0002e030 #define IRQSTAT_DMAE (0x10000000) @@ -96,6 +97,7 @@ #define PRSSTAT_CINS (0x00010000) #define PRSSTAT_BREN (0x00000800) #define PRSSTAT_BWEN (0x00000400) +#define PRSSTAT_SDOFF (0x00000080) #define PRSSTAT_SDSTB (0X00000008) #define PRSSTAT_DLA (0x00000004) #define PRSSTAT_CICHB (0x00000002) -- 2.17.1

5 7

Pull request for UEFI sub-system for efi-2021-04-rc2
by Heinrich Schuchardt 05 Feb '21

05 Feb '21

Dear Tom, The following changes since commit fdcb93e1709ab1a2ebb562455621617c29e2099c: Merge branch '2021-02-01-assorted-fixes' (2021-02-02 09:24:10 -0500) are available in the Git repository at: https://gitlab.denx.de/u-boot/custodians/u-boot-efi.git tags/efi-2021-04-rc2 for you to fetch changes up to 5489448cd7d46554f7f45a180754be78eff9f54d: doc: dm: describe end of life of plat_auto (2021-02-04 20:36:07 +0100) Gitlab CI showed no problems: https://gitlab.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/6216 ---------------------------------------------------------------- Pull request for UEFI sub-system for efi-2021-04-rc2 Bug fixes: * do not allow creating of files with filenames on FAT file system * install UEFI System Partition GUID on ESP handle * in dtbdump.efi test tool use GUID to find ESP handle Documentation: * man-page for load command * describe end of life of plat_auto ---------------------------------------------------------------- Heinrich Schuchardt (10): fs: fat: usage basename in file_fat_write_at, fat_mkdir fs: fat: must not write directory '.' and '..' fs: fat: remove trailing periods from long name efi_loader: only check size if EFI_DT_APPLY_FIXUPS efi_loader: install UEFI System Partition GUID efi_selftest: use GUID to find ESP in dtbdump efi_loader: VenMedia device path node doc: describe load command doc: return value exception command doc: dm: describe end of life of plat_auto cmd/efidebug.c | 5 ++ doc/driver-model/design.rst | 6 +-- doc/usage/exception.rst | 5 -- doc/usage/index.rst | 1 + doc/usage/load.rst | 74 +++++++++++++++++++++++++++ fs/fat/fat_write.c | 70 ++++++++++++++++---------- lib/efi_loader/efi_device_path_to_text.c | 15 ++++++ lib/efi_loader/efi_disk.c | 15 +++--- lib/efi_loader/efi_dt_fixup.c | 25 +++++----- lib/efi_selftest/dtbdump.c | 85 +++++++++++++++++++------------- 10 files changed, 214 insertions(+), 87 deletions(-) create mode 100644 doc/usage/load.rst

2 1

[v5 00/33] gpio: layerscape: fix gpio and enable gpio
by Biwen Li 05 Feb '21

05 Feb '21

From: Biwen Li <biwen.li(a)nxp.com> Change in v5: - fix build issue of gazerbeam Change in v4: - fix build issue of SoC ls1021a Change in v3: - update description Change in v2: - fix warnings when check patches - enable gpio command for boards ls1021atwr, ls1021aqds Biwen Li (33): gpio: mpc8xxx_gpio: Fix for litte endian arm: dts: ls1021a: add gpio node arm64: dts: ls1012a: add gpio node arm64: dts: ls1028a: add gpio node arm64: dts: ls1043a: add gpio node arm64: dts: ls1046a: add gpio node arm64: dts: ls1088a: add gpio node arm64: dts: ls208xa: add gpio node configs: ls1012a: enable CONFIG_MPC8XXX_GPIO configs: ls1043a: enable CONFIG_MPC8XXX_GPIO configs: ls1028a: enable CONFIG_MPC8XXX_GPIO configs: ls1088a: enable CONFIG_MPC8XXX_GPIO configs: ls208xa: enable CONFIG_MPC8XXX_GPIO configs: lx2160a: enable CONFIG_MPC8XXX_GPIO configs: ls1046a: enable MPC8XXX_GPIO configs: ls1021atwr: enable CONFIG_MPC8XXX_GPIO configs: ls1021aqds: enable CONFIG_MPC8XXX_GPIO configs: ls1012afrwy: enable CMD_GPIO configs: ls1012ardb: enable CMD_GPIO configs: ls1021aqds: enable CMD_GPIO configs: ls1021atwr: enable CMD_GPIO configs: ls1028aqds: enable CMD_GPIO configs: ls1028ardb: enable CMD_GPIO configs: ls1043aqds: enable CMD_GPIO configs: ls1043ardb: enable CMD_GPIO configs: ls1046ardb: enable CMD_GPIO configs: ls1046aqds: enable CMD_GPIO configs: ls2088ardb: enable DM_GPIO and CMD_GPIO configs: ls2088aqds: enable CMD_GPIO configs: ls1088aqds: enable DM_GPIO and CMD_GPIO configs: ls1088ardb: enable DM_GPIO and CMD_GPIO configs: lx2160ardb: enable CMD_GPIO configs: lx2160aqds: enable CMD_GPIO arch/arm/dts/fsl-ls1012a.dtsi | 20 ++++++++ arch/arm/dts/fsl-ls1028a.dtsi | 33 +++++++++++++ arch/arm/dts/fsl-ls1043a.dtsi | 40 ++++++++++++++++ arch/arm/dts/fsl-ls1046a.dtsi | 40 ++++++++++++++++ arch/arm/dts/fsl-ls1088a.dtsi | 47 ++++++++++++++++++- arch/arm/dts/fsl-ls2080a.dtsi | 46 +++++++++++++++++- arch/arm/dts/ls1021a.dtsi | 40 ++++++++++++++++ .../asm/arch-fsl-layerscape/immap_lsch3.h | 10 ++++ arch/arm/include/asm/arch-ls102xa/gpio.h | 16 +++++++ arch/powerpc/include/asm/immap_83xx.h | 13 +++++ .../ls1012afrwy_qspi_SECURE_BOOT_defconfig | 1 + configs/ls1012afrwy_qspi_defconfig | 1 + configs/ls1012afrwy_tfa_SECURE_BOOT_defconfig | 1 + configs/ls1012afrwy_tfa_defconfig | 1 + configs/ls1012ardb_qspi_SECURE_BOOT_defconfig | 1 + configs/ls1012ardb_qspi_defconfig | 1 + configs/ls1012ardb_tfa_SECURE_BOOT_defconfig | 1 + configs/ls1012ardb_tfa_defconfig | 1 + configs/ls1021aqds_ddr4_nor_defconfig | 1 + configs/ls1021aqds_ddr4_nor_lpuart_defconfig | 1 + configs/ls1021aqds_nand_defconfig | 1 + configs/ls1021aqds_nor_SECURE_BOOT_defconfig | 1 + configs/ls1021aqds_nor_defconfig | 1 + configs/ls1021aqds_nor_lpuart_defconfig | 1 + configs/ls1021aqds_qspi_defconfig | 1 + configs/ls1021aqds_sdcard_ifc_defconfig | 1 + configs/ls1021aqds_sdcard_qspi_defconfig | 1 + configs/ls1021atwr_nor_SECURE_BOOT_defconfig | 1 + configs/ls1021atwr_nor_defconfig | 1 + configs/ls1021atwr_nor_lpuart_defconfig | 1 + configs/ls1021atwr_qspi_defconfig | 1 + ...s1021atwr_sdcard_ifc_SECURE_BOOT_defconfig | 1 + configs/ls1021atwr_sdcard_ifc_defconfig | 1 + configs/ls1021atwr_sdcard_qspi_defconfig | 1 + configs/ls1028aqds_tfa_SECURE_BOOT_defconfig | 1 + configs/ls1028aqds_tfa_defconfig | 1 + configs/ls1028aqds_tfa_lpuart_defconfig | 1 + configs/ls1028ardb_tfa_SECURE_BOOT_defconfig | 1 + configs/ls1028ardb_tfa_defconfig | 1 + configs/ls1043aqds_defconfig | 1 + configs/ls1043aqds_lpuart_defconfig | 1 + configs/ls1043aqds_nand_defconfig | 1 + configs/ls1043aqds_nor_ddr3_defconfig | 1 + configs/ls1043aqds_qspi_defconfig | 1 + configs/ls1043aqds_sdcard_ifc_defconfig | 1 + configs/ls1043aqds_sdcard_qspi_defconfig | 1 + configs/ls1043aqds_tfa_SECURE_BOOT_defconfig | 1 + configs/ls1043aqds_tfa_defconfig | 1 + configs/ls1043ardb_SECURE_BOOT_defconfig | 1 + configs/ls1043ardb_defconfig | 1 + configs/ls1043ardb_nand_SECURE_BOOT_defconfig | 1 + configs/ls1043ardb_nand_defconfig | 1 + .../ls1043ardb_sdcard_SECURE_BOOT_defconfig | 1 + configs/ls1043ardb_sdcard_defconfig | 1 + configs/ls1043ardb_tfa_SECURE_BOOT_defconfig | 1 + configs/ls1043ardb_tfa_defconfig | 1 + configs/ls1046aqds_SECURE_BOOT_defconfig | 1 + configs/ls1046aqds_defconfig | 1 + configs/ls1046aqds_lpuart_defconfig | 1 + configs/ls1046aqds_nand_defconfig | 1 + configs/ls1046aqds_qspi_defconfig | 1 + configs/ls1046aqds_sdcard_ifc_defconfig | 1 + configs/ls1046aqds_sdcard_qspi_defconfig | 1 + configs/ls1046aqds_tfa_SECURE_BOOT_defconfig | 1 + configs/ls1046aqds_tfa_defconfig | 1 + configs/ls1046ardb_emmc_defconfig | 1 + configs/ls1046ardb_qspi_SECURE_BOOT_defconfig | 1 + configs/ls1046ardb_qspi_defconfig | 1 + configs/ls1046ardb_qspi_spl_defconfig | 1 + .../ls1046ardb_sdcard_SECURE_BOOT_defconfig | 1 + configs/ls1046ardb_sdcard_defconfig | 1 + configs/ls1046ardb_tfa_SECURE_BOOT_defconfig | 1 + configs/ls1046ardb_tfa_defconfig | 1 + configs/ls1088aqds_defconfig | 2 + configs/ls1088aqds_qspi_SECURE_BOOT_defconfig | 2 + configs/ls1088aqds_qspi_defconfig | 2 + configs/ls1088aqds_sdcard_ifc_defconfig | 2 + configs/ls1088aqds_sdcard_qspi_defconfig | 2 + configs/ls1088aqds_tfa_defconfig | 1 + configs/ls1088ardb_qspi_SECURE_BOOT_defconfig | 2 + configs/ls1088ardb_qspi_defconfig | 2 + ...1088ardb_sdcard_qspi_SECURE_BOOT_defconfig | 2 + configs/ls1088ardb_sdcard_qspi_defconfig | 2 + configs/ls1088ardb_tfa_SECURE_BOOT_defconfig | 1 + configs/ls1088ardb_tfa_defconfig | 1 + configs/ls2088aqds_tfa_defconfig | 1 + configs/ls2088ardb_qspi_SECURE_BOOT_defconfig | 2 + configs/ls2088ardb_qspi_defconfig | 2 + configs/ls2088ardb_tfa_SECURE_BOOT_defconfig | 1 + configs/ls2088ardb_tfa_defconfig | 1 + configs/lx2160aqds_tfa_SECURE_BOOT_defconfig | 1 + configs/lx2160aqds_tfa_defconfig | 1 + configs/lx2160ardb_tfa_SECURE_BOOT_defconfig | 1 + configs/lx2160ardb_tfa_defconfig | 1 + configs/lx2160ardb_tfa_stmm_defconfig | 1 + drivers/gpio/mpc8xxx_gpio.c | 47 ++++--------------- include/configs/ls1012a_common.h | 7 +++ include/configs/ls1021aqds.h | 7 +++ include/configs/ls1021atwr.h | 7 +++ include/configs/ls1028a_common.h | 7 +++ include/configs/ls1043a_common.h | 7 +++ include/configs/ls1046a_common.h | 7 +++ include/configs/ls1088a_common.h | 7 +++ include/configs/ls2080a_common.h | 7 +++ include/configs/lx2160a_common.h | 7 +++ 105 files changed, 470 insertions(+), 41 deletions(-) -- 2.17.1

1 33

[PATCH] board/km: fix setting of pram variable
by Holger Brunck 05 Feb '21

05 Feb '21

The pram variable is evaluated in common/board_r.c as a unsigned long and not as a string using a hex formataion. This incorrect setting leads to a wrong calculation of preserved RAM for u-boot. This is fixed now. The pram variable is now a unsigned long specifying the amount of kB of preserved RAM. Signed-off-by: Holger Brunck <holger.brunck(a)hitachi-powergrids.com> CC: Stefan Roese <sr(a)denx.de> --- board/keymile/common/common.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/board/keymile/common/common.c b/board/keymile/common/common.c index df507e2..7343d47 100644 --- a/board/keymile/common/common.c +++ b/board/keymile/common/common.c @@ -60,7 +60,7 @@ int set_km_env(void) strict_strtoul(p, 16, &rootfssize); pram = (rootfssize + CONFIG_KM_RESERVED_PRAM + CONFIG_KM_PHRAM + CONFIG_KM_PNVRAM) / 0x400; - sprintf((char *)buf, "0x%x", pram); + sprintf((char *)buf, "%u", pram); env_set("pram", (char *)buf); varaddr = gd->ram_size - CONFIG_KM_RESERVED_PRAM - CONFIG_KM_PHRAM; -- 1.8.3.1

2 2

RE: [PATCH v5 5/5] board/km: add support for seli8 design based on nxp ls102x
by Aleksandar Gerasimovski 05 Feb '21

05 Feb '21

The SELI8 design is a new tdm service unit card for Hitachi-Powergrids XMC and FOX product lines. It is based on NXP LS1021 SoC and it provides following interfaces: - IFC interface for NOR, NAND and external FPGA's - 1 x RGMII ETH for debug purposes - 2 x SGMII ETH for management communication via back-plane - 1 x uQE HDLC for management communication via back-plane - 1 x I2C for peripheral devices - 1 x SPI for peripheral devices - 1 x UART for debug logging It is foreseen that the design will be later re-used for another XMC and FOX service cards with similar SoC requirements. Signed-off-by: Rainer Boschung <rainer.boschung(a)hitachi-powergrids.com> Signed-off-by: Matteo Ghidoni <matteo.ghidoni(a)hitachi-powergrids.com> Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski(a)hitachi-powergrids.com> --- Changes for v2: - fix patch subject to 60 characters Changes for v3: - remove obsolete CMDLINE_TAG Changes for v4: - include i2c deblocking to keymile/common.h - move Kconfig's from board.h to board defconfig - fix ENV_SIZE, it was typo or copy-paste error Changes for v5: - more CONFIG_ moved to defconfig, what's possible is moved --- --- arch/arm/Kconfig | 19 ++ arch/arm/dts/Makefile | 2 + arch/arm/dts/ls1021a-pg-wcom-seli8.dts | 111 +++++++++ board/keymile/Kconfig | 23 +- board/keymile/common/ivm.c | 19 +- board/keymile/pg-wcom-ls102xa/Kconfig | 19 ++ board/keymile/pg-wcom-ls102xa/MAINTAINERS | 10 + board/keymile/pg-wcom-ls102xa/Makefile | 11 + board/keymile/pg-wcom-ls102xa/ddr.c | 90 ++++++++ board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c | 160 +++++++++++++ configs/pg_wcom_seli8_defconfig | 70 ++++++ include/configs/km/pg-wcom-ls102xa.h | 292 ++++++++++++++++++++++++ include/configs/pg-wcom-seli8.h | 45 ++++ 13 files changed, 860 insertions(+), 11 deletions(-) create mode 100644 arch/arm/dts/ls1021a-pg-wcom-seli8.dts create mode 100644 board/keymile/pg-wcom-ls102xa/Kconfig create mode 100644 board/keymile/pg-wcom-ls102xa/MAINTAINERS create mode 100644 board/keymile/pg-wcom-ls102xa/Makefile create mode 100644 board/keymile/pg-wcom-ls102xa/ddr.c create mode 100644 board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c create mode 100644 configs/pg_wcom_seli8_defconfig create mode 100644 include/configs/km/pg-wcom-ls102xa.h create mode 100644 include/configs/pg-wcom-seli8.h diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 95557d6..729f1a3 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1517,6 +1517,24 @@ config TARGET_LS1021ATWR select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI imply SCSI +config TARGET_PG_WCOM_SELI8 + bool "Support Hitachi-Powergrids SELI8 service unit card" + select ARCH_LS1021A + select ARCH_SUPPORT_PSCI + select BOARD_EARLY_INIT_F + select BOARD_LATE_INIT + select CPU_V7A + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select SYS_FSL_DDR + select FSL_DDR_INTERACTIVE + select VENDOR_KM + imply SCSI + help + Support for Hitachi-Powergrids SELI8 service unit card. + SELI8 is a QorIQ LS1021a based service unit card used + in XMC20 and FOX615 product families. + config TARGET_LS1021ATSN bool "Support ls1021atsn" select ARCH_LS1021A @@ -2036,6 +2054,7 @@ source "board/variscite/dart_6ul/Kconfig" source "board/vscom/baltos/Kconfig" source "board/phytium/durian/Kconfig" source "board/xen/xenguest_arm64/Kconfig" +source "board/keymile/Kconfig" source "arch/arm/Kconfig.debug" diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 858b79a..dbc71c0 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -399,6 +399,8 @@ dtb-$(CONFIG_ARCH_LS1021A) += ls1021a-qds-duart.dtb \ ls1021a-qds-lpuart.dtb \ ls1021a-twr-duart.dtb ls1021a-twr-lpuart.dtb \ ls1021a-iot-duart.dtb ls1021a-tsn.dtb +dtb-$(CONFIG_TARGET_PG_WCOM_SELI8) += ls1021a-pg-wcom-seli8.dtb + dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \ fsl-ls2080a-qds-42-x.dtb \ fsl-ls2080a-rdb.dtb \ diff --git a/arch/arm/dts/ls1021a-pg-wcom-seli8.dts b/arch/arm/dts/ls1021a-pg-wcom-seli8.dts new file mode 100644 index 0000000..e335188 --- /dev/null +++ b/arch/arm/dts/ls1021a-pg-wcom-seli8.dts @@ -0,0 +1,111 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2013-2015 Freescale Semiconductor, Inc. + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +/dts-v1/; +#include "ls1021a.dtsi" + +/ { + model = "Hitachi-Powergrids SELI8 Service Unit for XMC and FOX"; + + chosen { + stdout-path = &uart0; + }; +}; + +&enet0 { + status = "okay"; + tbi-handle = <&tbi0>; + phy-connection-type = "sgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&enet1 { + status = "okay"; + tbi-handle = <&tbi1>; + phy-connection-type = "sgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&enet2 { + phy-handle = <&debug_phy>; + phy-connection-type = "rgmii-id"; + status = "okay"; +}; + +&i2c0 { + status = "okay"; +}; + +&ifc { + #address-cells = <2>; + #size-cells = <1>; + /* NOR Flash on board */ + ranges = <0x0 0x0 0x60000000 0x04000000>; + status = "okay"; + + nor@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x4000000>; + bank-width = <2>; + device-width = <1>; + + partition@0 { + label = "rcw"; + reg = <0x0 0x20000>; + read-only; + }; + partition@20000 { + label = "qe"; + reg = <0x20000 0x20000>; + }; + partition@40000 { + label = "envred"; + reg = <0x40000 0x20000>; + }; + partition@60000 { + label = "env"; + reg = <0x60000 0x20000>; + }; + partition@100000 { + label = "u-boot"; + reg = <0x100000 0x100000>; + }; + partition@200000 { + label = "ubi0"; + reg = <0x200000 0x3E00000>; + }; + }; +}; + +&mdio0 { + debug_phy: ethernet-phy@11 { + reg = <0x11>; + }; + + tbi0: tbi-phy@0xb { + reg = <0xb>; + device_type = "tbi-phy"; + }; +}; + +&mdio1 { + tbi1: tbi-phy@0xd { + reg = <0xd>; + device_type = "tbi-phy"; + }; +}; + +&uart0 { + status = "okay"; +}; diff --git a/board/keymile/Kconfig b/board/keymile/Kconfig index e590690..965a537 100644 --- a/board/keymile/Kconfig +++ b/board/keymile/Kconfig @@ -20,8 +20,8 @@ config KM_PNVRAM config KM_PHRAM hex "Physical RAM" - default 0x17F000 if ARM - default 0x100000 if PPC + default 0x17F000 if ARM && !ARCH_LS1021A + default 0x100000 if PPC || ARCH_LS1021A depends on !ARCH_SOCFPGA help Start address of the physical RAM, which is the mounted /var folder. @@ -30,13 +30,14 @@ config KM_RESERVED_PRAM hex "Reserved RAM" default 0x801000 if ARCH_KIRKWOOD default 0x0 if MPC83xx - default 0x1000 if MPC85xx + default 0x1000 if MPC85xx || ARCH_LS1021A depends on !ARCH_SOCFPGA help Reserved physical RAM area at the end of memory for special purposes. config KM_CRAMFS_ADDR hex "CRAMFS Address" + default 0x83000000 if ARCH_LS1021A default 0x3000000 depends on !ARCH_SOCFPGA help @@ -44,16 +45,25 @@ config KM_CRAMFS_ADDR config KM_KERNEL_ADDR hex "Kernel Load Address" + default 0x82000000 if ARCH_LS1021A default 0x2000000 help Address where to load Linux kernel in RAM. config KM_FDT_ADDR hex "FDT Load Address" + default 0x82FC0000 if ARCH_LS1021A default 0x2FC0000 help Address where to load flattened device tree in RAM. +config SYS_PAX_BASE + hex "PAX IFC Base Address" + default 0x78000000 + depends on ARCH_LS1021A + help + IFC Base Address for PAXx FPGA. + config KM_CONSOLE_TTY string "KM Console" default "ttyS0" @@ -69,9 +79,9 @@ config KM_DEF_NETDEV config KM_COMMON_ETH_INIT bool "Common Ethernet Initialization" default y if ARCH_KIRKWOOD || MPC83xx - default n if MPC85xx || ARCH_SOCFPGA + default n if MPC85xx || ARCH_SOCFPGA || ARCH_LS1021A help - Use the Ethernet initialization implemented in common code, which + Use the Ethernet initialization implemented in common code that detects if a Piggy board is present. config PIGGY_MAC_ADDRESS_OFFSET @@ -90,7 +100,7 @@ config KM_MVEXTSW_ADDR config KM_IVM_BUS int "IVM I2C Bus" default 0 if ARCH_SOCFPGA - default 1 if ARCH_KIRKWOOD || MPC85xx + default 1 if ARCH_KIRKWOOD || MPC85xx || ARCH_LS1021A default 2 if MPC83xx help Identifier number of I2C bus, where the inventory EEPROM is connected to. @@ -116,6 +126,7 @@ config SYS_IVM_EEPROM_PAGE_LEN source "board/keymile/km83xx/Kconfig" source "board/keymile/kmp204x/Kconfig" source "board/keymile/km_arm/Kconfig" +source "board/keymile/pg-wcom-ls102xa/Kconfig" endmenu diff --git a/board/keymile/common/ivm.c b/board/keymile/common/ivm.c index e989bf6..48817cb 100644 --- a/board/keymile/common/ivm.c +++ b/board/keymile/common/ivm.c @@ -306,11 +306,7 @@ static int ivm_populate_env(unsigned char *buf, int len, int mac_address_offset) return 0; page2 = &buf[CONFIG_SYS_IVM_EEPROM_PAGE_LEN * 2]; - if (!IS_ENABLED(CONFIG_KMTEGR1)) { - /* if an offset is defined, add it */ - process_mac(valbuf, page2, mac_address_offset, true); - env_set((char *)"ethaddr", (char *)valbuf); - } else { + if (IS_ENABLED(CONFIG_KMTEGR1)) { /* KMTEGR1 has a special setup. eth0 has no connection to the * outside and gets an locally administred MAC address, eth1 is * the debug interface and gets the official MAC address from @@ -320,6 +316,19 @@ static int ivm_populate_env(unsigned char *buf, int len, int mac_address_offset) env_set((char *)"ethaddr", (char *)valbuf); process_mac(valbuf, page2, mac_address_offset, true); env_set((char *)"eth1addr", (char *)valbuf); + } else if (IS_ENABLED(CONFIG_ARCH_LS1021A)) { + /* LS102xA has 1xRGMII for debug connection and + * 2xSGMII for back-plane mgmt connection + */ + process_mac(valbuf, page2, 1, true); + env_set((char *)"ethaddr", (char *)valbuf); + process_mac(valbuf, page2, 2, true); + env_set((char *)"eth1addr", (char *)valbuf); + process_mac(valbuf, page2, mac_address_offset, true); + env_set((char *)"eth2addr", (char *)valbuf); + } else { + process_mac(valbuf, page2, mac_address_offset, true); + env_set((char *)"ethaddr", (char *)valbuf); } return 0; diff --git a/board/keymile/pg-wcom-ls102xa/Kconfig b/board/keymile/pg-wcom-ls102xa/Kconfig new file mode 100644 index 0000000..15c009d --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/Kconfig @@ -0,0 +1,19 @@ +if TARGET_PG_WCOM_SELI8 + +config SYS_BOARD + default "pg-wcom-ls102xa" + +config SYS_VENDOR + default "keymile" + +config SYS_SOC + default "ls102xa" + +config SYS_CONFIG_NAME + default "pg-wcom-seli8" + +config BOARD_SPECIFIC_OPTIONS + def_bool y + imply FS_CRAMFS + +endif diff --git a/board/keymile/pg-wcom-ls102xa/MAINTAINERS b/board/keymile/pg-wcom-ls102xa/MAINTAINERS new file mode 100644 index 0000000..e1bc90a --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/MAINTAINERS @@ -0,0 +1,10 @@ +Hitachi Power Grids LS102XA BOARD +M: Aleksandar Gerasimovski <aleksandar.gerasimovski(a)hitachi-powergrids.com> +M: Rainer Boschung <rainer.boschung(a)hitachi-powergrids.com> +M: Matteo Ghidoni <matteo.ghidoni(a)hitachi-powergrids.com> +S: Maintained +F: board/keymile/pg-wcom-ls102xa/ +F: include/configs/km/pg-wcom-ls102xa.h +F: include/configs/pg-wcom-seli8.h +F: configs/pg_wcom_seli8_defconfig +F: arch/arm/dts/ls1021a-pg-wcom-seli8.dts diff --git a/board/keymile/pg-wcom-ls102xa/Makefile b/board/keymile/pg-wcom-ls102xa/Makefile new file mode 100644 index 0000000..229b0c2 --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/Makefile @@ -0,0 +1,11 @@ +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright 2021 Hitachi Power Grids. All rights reserved. +# + +obj-y += pg-wcom-ls102xa.o ddr.o +obj-y += ../common/common.o ../common/ivm.o ../common/qrio.o +obj-$(CONFIG_LAYERSCAPE_NS_ACCESS) += ../../freescale/common/ns_access.o +obj-$(CONFIG_LS102XA_STREAM_ID) += ../../freescale/common/ls102xa_stream_id.o +obj-$(CONFIG_ID_EEPROM) += ../../freescale/common/sys_eeprom.o diff --git a/board/keymile/pg-wcom-ls102xa/ddr.c b/board/keymile/pg-wcom-ls102xa/ddr.c new file mode 100644 index 0000000..6023573 --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/ddr.c @@ -0,0 +1,90 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +#include <common.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> +#include <asm/io.h> +#include <asm/arch/clock.h> +#include <asm/arch/ls102xa_soc.h> + +DECLARE_GLOBAL_DATA_PTR; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + if (ctrl_num > 1) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + + // 1/2 DRAM cycle (should be increased in case of ADDR/CMD heavily loaded than the clock) + popts->clk_adjust = 0x4; + popts->write_data_delay = 0x4; + // wr leveling start value for lane 0 + popts->wrlvl_start = 0x5; + // wr leveling start values for lanes 1-3 (lane 4 not there) + popts->wrlvl_ctl_2 = 0x05050500; + // 32-bit DRAM, no need to set start values for lanes we do not have (5-8) + popts->wrlvl_ctl_3 = 0x0; + popts->cpo_override = 0x1f; + + /* force DDR bus width to 32 bits */ + popts->data_bus_width = 1; + popts->otf_burst_chop_en = 0; + popts->burst_length = DDR_BL8; + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 1; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * Rtt and Rtt_WR override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + popts->cswl_override = DDR_CSWL_CS0; + + /* optimize cpo for erratum A-009942 */ + popts->cpo_sample = 0x58; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); +} + +int fsl_initdram(void) +{ + phys_size_t dram_size; + + puts("Initializing DDR....using SPD\n"); + dram_size = fsl_ddr_sdram(); + + erratum_a008850_post(); + + gd->ram_size = dram_size; + + return 0; +} + +int dram_init_banksize(void) +{ + gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; + gd->bd->bi_dram[0].size = gd->ram_size; + + return 0; +} diff --git a/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c b/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c new file mode 100644 index 0000000..6b0e963 --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c @@ -0,0 +1,160 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +#include <common.h> +#include <i2c.h> +#include <asm/io.h> +#include <asm/arch/immap_ls102xa.h> +#include <asm/arch/clock.h> +#include <asm/arch/fsl_serdes.h> +#include <asm/arch/ls102xa_devdis.h> +#include <asm/arch/ls102xa_soc.h> +#include <hwconfig.h> +#include <mmc.h> +#include <fsl_csu.h> +#include <fsl_esdhc.h> +#include <fsl_ifc.h> +#include <fsl_immap.h> +#include <netdev.h> +#include <fsl_mdio.h> +#include <tsec.h> +#include <fsl_sec.h> +#include <fsl_devdis.h> +#include <fsl_ddr.h> +#include <spl.h> +#include <fdt_support.h> +#include <fsl_qe.h> +#include <fsl_validate.h> + +#include "../common/common.h" +#include "../common/qrio.h" + +DECLARE_GLOBAL_DATA_PTR; + +static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN]; + +int checkboard(void) +{ + show_qrio(); + + return 0; +} + +int dram_init(void) +{ + return fsl_initdram(); +} + +int board_early_init_f(void) +{ + struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR; + struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR; + struct fsl_ifc ifc = {(void *)CONFIG_SYS_IFC_ADDR, (void *)NULL}; + + /* Disable unused MCK1 */ + setbits_be32(&gur->ddrclkdr, 2); + + /* IFC Global Configuration */ + setbits_be32(&ifc.gregs->ifc_gcr, 12 << IFC_GCR_TBCTL_TRN_TIME_SHIFT); + setbits_be32(&ifc.gregs->ifc_ccr, IFC_CCR_CLK_DIV(3) | + IFC_CCR_INV_CLK_EN); + + /* clear BD & FR bits for BE BD's and frame data */ + clrbits_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR); + out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125); + + init_early_memctl_regs(); + + /* QRIO Configuration */ + qrio_uprstreq(UPREQ_CORE_RST); + + if (IS_ENABLED(CONFIG_TARGET_PG_WCOM_SELI8)) { + qrio_prstcfg(KM_LIU_RST, PRSTCFG_POWUP_UNIT_RST); + qrio_wdmask(KM_LIU_RST, true); + + qrio_prstcfg(KM_PAXK_RST, PRSTCFG_POWUP_UNIT_RST); + qrio_wdmask(KM_PAXK_RST, true); + + qrio_prstcfg(KM_DBG_ETH_RST, PRSTCFG_POWUP_UNIT_CORE_RST); + qrio_prst(KM_DBG_ETH_RST, false, false); + } + + i2c_deblock_gpio_cfg(); + + arch_soc_init(); + + return 0; +} + +int board_init(void) +{ + if (IS_ENABLED(CONFIG_SYS_FSL_ERRATUM_A010315)) + erratum_a010315(); + + fsl_serdes_init(); + + ls102xa_smmu_stream_id_init(); + + u_qe_init(); + + return 0; +} + +int board_late_init(void) +{ + return 0; +} + +int misc_init_r(void) +{ + if (IS_ENABLED(CONFIG_FSL_DEVICE_DISABLE)) + device_disable(devdis_tbl, ARRAY_SIZE(devdis_tbl)); + + ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN, + CONFIG_PIGGY_MAC_ADDRESS_OFFSET); + + return 0; +} + +int ft_board_setup(void *blob, struct bd_info *bd) +{ + ft_cpu_setup(blob, bd); + + if (IS_ENABLED(CONFIG_PCI)) + ft_pci_setup(blob, bd); + + return 0; +} + +u8 flash_read8(void *addr) +{ + return __raw_readb(addr + 1); +} + +void flash_write16(u16 val, void *addr) +{ + u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00)); + + __raw_writew(shftval, addr); +} + +u16 flash_read16(void *addr) +{ + u16 val = __raw_readw(addr); + + return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00); +} + +int hush_init_var(void) +{ + ivm_analyze_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN); + return 0; +} + +int last_stage_init(void) +{ + set_km_env(); + return 0; +} diff --git a/configs/pg_wcom_seli8_defconfig b/configs/pg_wcom_seli8_defconfig new file mode 100644 index 0000000..7d1a28a --- /dev/null +++ b/configs/pg_wcom_seli8_defconfig @@ -0,0 +1,70 @@ +CONFIG_ARM=y +CONFIG_TARGET_PG_WCOM_SELI8=y +CONFIG_SYS_TEXT_BASE=0x60100000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_KM_DEF_NETDEV="eth2" +CONFIG_KM_COMMON_ETH_INIT=y +CONFIG_PIGGY_MAC_ADDRESS_OFFSET=3 +CONFIG_SYS_MEMTEST_START=0x80000000 +CONFIG_SYS_MEMTEST_END=0x9fffffff +CONFIG_ENV_SIZE=0x20000 +CONFIG_ENV_SECT_SIZE=0x20000 +CONFIG_BOOTCOUNT_BOOTLIMIT=3 +CONFIG_SYS_BOOTCOUNT_ADDR=0x70000020 +CONFIG_DEFAULT_DEVICE_TREE="ls1021a-pg-wcom-seli8" +CONFIG_AHCI=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_BOOTDELAY=3 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0" +CONFIG_SILENT_CONSOLE=y +CONFIG_MISC_INIT_R=y +CONFIG_LAST_STAGE_INIT=y +CONFIG_CMD_IMLS=y +CONFIG_CMD_GREPENV=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_NAND=y +CONFIG_CMD_NAND_TRIMFFS=y +CONFIG_CMD_CRAMFS=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nor0=60000000.nor,nand0=68000000.flash" +CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:128k(rcw),128k(qe),128k(envred),128k(env),512k(res),1m(u-boot),-(ubi0);68000000.flash:-(ubi1)" +CONFIG_CMD_UBI=y +CONFIG_OF_CONTROL=y +CONFIG_ENV_IS_IN_FLASH=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_ADDR=0x60060000 +CONFIG_ENV_ADDR_REDUND=0x60040000 +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y +CONFIG_DM=y +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_SYS_FSL_DDR3=y +# CONFIG_MMC is not set +CONFIG_SYS_I2C_MXC=y +CONFIG_SYS_I2C_MXC_I2C1=y +CONFIG_SYS_I2C_MXC_I2C2=y +CONFIG_SYS_I2C_MXC_I2C3=y +CONFIG_MTD=y +CONFIG_MTD_NOR_FLASH=y +CONFIG_FLASH_CFI_DRIVER=y +CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y +CONFIG_FLASH_CFI_MTD=y +CONFIG_SYS_FLASH_CFI=y +CONFIG_MTD_RAW_NAND=y +CONFIG_PHY_MARVELL=y +CONFIG_PHY_FIXED=y +CONFIG_DM_ETH=y +CONFIG_DM_MDIO=y +CONFIG_PHY_GIGE=y +CONFIG_MII=y +CONFIG_TSEC_ENET=y +CONFIG_SPECIFY_CONSOLE_INDEX=y +CONFIG_DM_SERIAL=y +CONFIG_SYS_NS16550=y diff --git a/include/configs/km/pg-wcom-ls102xa.h b/include/configs/km/pg-wcom-ls102xa.h new file mode 100644 index 0000000..e248832 --- /dev/null +++ b/include/configs/km/pg-wcom-ls102xa.h @@ -0,0 +1,292 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +#ifndef __CONFIG_PG_WCOM_LS102XA_H +#define __CONFIG_PG_WCOM_LS102XA_H + +#define CONFIG_SYS_FSL_CLK + +#define CONFIG_SKIP_LOWLEVEL_INIT + +/* include common defines/options for all Keymile boards */ +#include "keymile-common.h" + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024) + +#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE + +#define CONFIG_SYS_CLK_FREQ 66666666 +/* + * Take into account default implementation where DDR_FDBK_MULTI is consider as + * configured for DDR_PLL = 2*MEM_PLL_RAT. + * In our case DDR_FDBK_MULTI is 2, means DDR_PLL = MEM_PLL_RAT. + */ +#define CONFIG_DDR_CLK_FREQ (100000000 >> 1) + +#define PHYS_SDRAM 0x80000000 +#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 4 + +#define CONFIG_DDR_SPD + +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x54 + +/* + * IFC Definitions + */ +/* NOR Flash Definitions */ +#define CONFIG_FSL_IFC +#define CONFIG_SYS_FLASH_BASE 0x60000000 +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE + +#define CONFIG_SYS_NOR0_CSPR_EXT (0x0) +#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_TE | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(64 * 1024 * 1024) + +#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_AVD_TGL_PGM_EN | \ + CSOR_NOR_ADM_SHIFT(0x4) | \ + CSOR_NOR_NOR_MODE_AYSNC_NOR | \ + CSOR_NOR_TRHZ_20 | \ + CSOR_NOR_BCTLD) +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x1) | \ + FTIM0_NOR_TEADC(0x7) | \ + FTIM0_NOR_TAVDS(0x0) | \ + FTIM0_NOR_TEAHC(0x1)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1) | \ + FTIM1_NOR_TRAD_NOR(0x21) | \ + FTIM1_NOR_TSEQRAD_NOR(0x21)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x1) | \ + FTIM2_NOR_TCH(0x1) | \ + FTIM2_NOR_TWPH(0x6) | \ + FTIM2_NOR_TWP(0xb)) +#define CONFIG_SYS_NOR_FTIM3 0 + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS } + +#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS +#define CONFIG_SYS_WRITE_SWAPPED_DATA + +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 + +/* NAND Flash Definitions */ +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_BASE 0x68000000 +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE + +#define CONFIG_SYS_NAND_CSPR_EXT (0x0) +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE) | \ + CSPR_PORT_SIZE_8 | \ + CSPR_TE | \ + CSPR_MSEL_NAND | \ + CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN \ + | CSOR_NAND_ECC_DEC_EN \ + | CSOR_NAND_ECC_MODE_4 \ + | CSOR_NAND_RAL_3 \ + | CSOR_NAND_PGS_2K \ + | CSOR_NAND_SPRZ_64 \ + | CSOR_NAND_PB(64) \ + | CSOR_NAND_TRHZ_40 \ + | CSOR_NAND_BCTLD) + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x3) | \ + FTIM0_NAND_TWP(0x8) | \ + FTIM0_NAND_TWCHT(0x3) | \ + FTIM0_NAND_TWH(0x5)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x1e) | \ + FTIM1_NAND_TWBE(0x1e) | \ + FTIM1_NAND_TRR(0x6) | \ + FTIM1_NAND_TRP(0x8)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x9) | \ + FTIM2_NAND_TREH(0x5) | \ + FTIM2_NAND_TWHRE(0x3c)) +#define CONFIG_SYS_NAND_FTIM3 (FTIM3_NAND_TWW(0x1e)) + +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 + +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +/* QRIO FPGA Definitions */ +#define CONFIG_SYS_QRIO_BASE 0x70000000 +#define CONFIG_SYS_QRIO_BASE_PHYS CONFIG_SYS_QRIO_BASE + +#define CONFIG_SYS_CSPR2_EXT (0x00) +#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE) | \ + CSPR_PORT_SIZE_8 | \ + CSPR_TE | \ + CSPR_MSEL_GPCM | \ + CSPR_V) +#define CONFIG_SYS_AMASK2 IFC_AMASK(64 * 1024) +#define CONFIG_SYS_CSOR2 (CSOR_GPCM_ADM_SHIFT(0x4) | \ + CSOR_GPCM_TRHZ_20 | \ + CSOR_GPCM_BCTLD) +#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x2) | \ + FTIM0_GPCM_TEADC(0x8) | \ + FTIM0_GPCM_TEAHC(0x2)) +#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x2) | \ + FTIM1_GPCM_TRAD(0x6)) +#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x1) | \ + FTIM2_GPCM_TCH(0x1) | \ + FTIM2_GPCM_TWP(0x7)) +#define CONFIG_SYS_CS2_FTIM3 0x04000000 + +/* + * Serial Port + */ +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + +/* + * I2C + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_INIT_BOARD +#define CONFIG_SYS_I2C_SPEED 100000 + +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_MAX_HOPS 1 +#define CONFIG_SYS_NUM_I2C_BUSES 3 +#define I2C_MUX_PCA_ADDR 0x70 +#define I2C_MUX_CH_DEFAULT 0x0 +#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \ + {1, {I2C_NULL_HOP} }, \ + } + +/* + * eTSEC + */ +#ifdef CONFIG_TSEC_ENET +#define CONFIG_ETHPRIME "ethernet@2d90000" +#endif + +#define CONFIG_LAYERSCAPE_NS_ACCESS +#define CONFIG_SMP_PEN_ADDR 0x01ee0200 +#define COUNTER_FREQUENCY 12500000 + +#define CONFIG_HWCONFIG +#define HWCONFIG_BUFFER_SIZE 256 +#define CONFIG_FSL_DEVICE_DISABLE + +/* + * Miscellaneous configurable options + */ + +#define CONFIG_SYS_LOAD_ADDR 0x82000000 + +#define CONFIG_LS102XA_STREAM_ID + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_LEN 0x100000 /* 1Mbyte */ +#define CONFIG_SYS_QE_FW_ADDR 0x60020000 + +#define CONFIG_SYS_BOOTCOUNT_BE + +/* + * Environment + */ + +#define CONFIG_ENV_TOTAL_SIZE 0x40000 +#define ENV_DEL_ADDR CONFIG_ENV_ADDR_REDUND /* direct for newenv */ + +#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ +#define CONFIG_KM_DEF_ENV +#endif + +#ifndef CONFIG_KM_DEF_BOOT_ARGS_CPU +#define CONFIG_KM_DEF_BOOT_ARGS_CPU "" +#endif + +#define CONFIG_KM_DEF_ENV_CPU \ + "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \ + "cramfsloadfdt=" \ + "cramfsload ${fdt_addr_r} " \ + "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \ + "u-boot=" CONFIG_HOSTNAME "/u-boot.bin\0" \ + "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize} && " \ + "erase " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize} && " \ + "cp.b ${load_addr_r} " \ + __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize} && " \ + "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize}\0" \ + "update-nor=protect off " __stringify(CONFIG_SYS_FLASH_BASE) \ + " +${filesize} && " \ + "erase " __stringify(CONFIG_SYS_FLASH_BASE) \ + " +${filesize} && " \ + "cp.b ${load_addr_r} " \ + __stringify(CONFIG_SYS_FLASH_BASE) " ${filesize} && " \ + "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +" __stringify(CONFIG_SYS_MONITOR_LEN)"\0" \ + "set_fdthigh=true\0" \ + "checkfdt=true\0" \ + "" + +#define CONFIG_KM_NEW_ENV \ + "newenv=protect off " __stringify(ENV_DEL_ADDR) \ + " +" __stringify(CONFIG_ENV_TOTAL_SIZE) " && " \ + "erase " __stringify(ENV_DEL_ADDR) \ + " +" __stringify(CONFIG_ENV_TOTAL_SIZE) " && " \ + "protect on " __stringify(ENV_DEL_ADDR) \ + " +" __stringify(CONFIG_ENV_TOTAL_SIZE) "\0" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_KM_NEW_ENV \ + CONFIG_KM_DEF_ENV \ + "EEprom_ivm=pca9547:70:9\0" \ + "" + +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Increase map for Linux */ + +#endif diff --git a/include/configs/pg-wcom-seli8.h b/include/configs/pg-wcom-seli8.h new file mode 100644 index 0000000..9a7669c --- /dev/null +++ b/include/configs/pg-wcom-seli8.h @@ -0,0 +1,45 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +#ifndef __CONFIG_PG_WCOM_SELI8_H +#define __CONFIG_PG_WCOM_SELI8_H + +#define CONFIG_HOSTNAME "SELI8" + +#define CONFIG_KM_UBI_PARTITION_NAME_BOOT "ubi0" +#define CONFIG_KM_UBI_PARTITION_NAME_APP "ubi1" + +/* PAXK FPGA Definitions */ +#define CONFIG_SYS_CSPR3_EXT (0x00) +#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(CONFIG_SYS_PAX_BASE) | \ + CSPR_PORT_SIZE_8 | \ + CSPR_MSEL_GPCM | \ + CSPR_V) +#define CONFIG_SYS_AMASK3 IFC_AMASK(64 * 1024) +#define CONFIG_SYS_CSOR3 (CSOR_GPCM_ADM_SHIFT(0x4) | \ + CSOR_GPCM_TRHZ_40) +#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x6) | \ + FTIM0_GPCM_TEADC(0x7) | \ + FTIM0_GPCM_TEAHC(0x2)) +#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x2) | \ + FTIM1_GPCM_TRAD(0x12)) +#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x3) | \ + FTIM2_GPCM_TCH(0x1) | \ + FTIM2_GPCM_TWP(0x12)) +#define CONFIG_SYS_CS3_FTIM3 0x04000000 + +/* PRST */ +#define KM_LIU_RST 0 +#define KM_PAXK_RST 1 +#define KM_DBG_ETH_RST 15 + +/* QRIO GPIOs used for deblocking */ +#define KM_I2C_DEBLOCK_PORT QRIO_GPIO_A +#define KM_I2C_DEBLOCK_SCL 20 +#define KM_I2C_DEBLOCK_SDA 21 + +#include "km/pg-wcom-ls102xa.h" + +#endif /* __CONFIG_PG_WCOM_SELI8_H */ -- 1.8.3.1 -----Original Message----- From: Aleksandar Gerasimovski Sent: Freitag, 5. Februar 2021 07:06 To: Tom Rini <trini(a)konsulko.com> Cc: Priyanka Jain (OSS) <priyanka.jain(a)oss.nxp.com>; Priyanka Jain <priyanka.jain(a)nxp.com>; u-boot(a)lists.denx.de; Valentin Longchamp <valentin.longchamp(a)hitachi-powergrids.com>; Holger Brunck <holger.brunck(a)hitachi-powergrids.com>; Rainer Boschung <rainer.boschung(a)hitachi-powergrids.com>; Matteo Ghidoni <matteo.ghidoni(a)hitachi-powergrids.com> Subject: RE: [PATCH v4 5/5] board/km: add support for seli8 design based on nxp ls102x The SELI8 design is a new tdm service unit card for Hitachi-Powergrids XMC and FOX product lines. It is based on NXP LS1021 SoC and it provides following interfaces: - IFC interface for NOR, NAND and external FPGA's - 1 x RGMII ETH for debug purposes - 2 x SGMII ETH for management communication via back-plane - 1 x uQE HDLC for management communication via back-plane - 1 x I2C for peripheral devices - 1 x SPI for peripheral devices - 1 x UART for debug logging It is foreseen that the design will be later re-used for another XMC and FOX service cards with similar SoC requirements. Signed-off-by: Rainer Boschung <rainer.boschung(a)hitachi-powergrids.com> Signed-off-by: Matteo Ghidoni <matteo.ghidoni(a)hitachi-powergrids.com> Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski(a)hitachi-powergrids.com> --- Changes for v2: - fix patch subject to 60 characters Changes for v3: - remove obsolete CMDLINE_TAG Changes for v4: - rebase, include i2c deblocking from keymile/common.h - move Kconfig's from board.h to board defconfig - fix ENV_SIZE, it was typo or copy-paste error --- --- arch/arm/Kconfig | 19 ++ arch/arm/dts/Makefile | 2 + arch/arm/dts/ls1021a-pg-wcom-seli8.dts | 111 +++++++++ board/keymile/Kconfig | 23 +- board/keymile/common/ivm.c | 19 +- board/keymile/pg-wcom-ls102xa/Kconfig | 19 ++ board/keymile/pg-wcom-ls102xa/MAINTAINERS | 10 + board/keymile/pg-wcom-ls102xa/Makefile | 11 + board/keymile/pg-wcom-ls102xa/ddr.c | 90 +++++++ board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c | 160 +++++++++++++ configs/pg_wcom_seli8_defconfig | 65 ++++++ include/configs/km/pg-wcom-ls102xa.h | 297 ++++++++++++++++++++++++ include/configs/pg-wcom-seli8.h | 45 ++++ 13 files changed, 860 insertions(+), 11 deletions(-) create mode 100644 arch/arm/dts/ls1021a-pg-wcom-seli8.dts create mode 100644 board/keymile/pg-wcom-ls102xa/Kconfig create mode 100644 board/keymile/pg-wcom-ls102xa/MAINTAINERS create mode 100644 board/keymile/pg-wcom-ls102xa/Makefile create mode 100644 board/keymile/pg-wcom-ls102xa/ddr.c create mode 100644 board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c create mode 100644 configs/pg_wcom_seli8_defconfig create mode 100644 include/configs/km/pg-wcom-ls102xa.h create mode 100644 include/configs/pg-wcom-seli8.h diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 95557d6..729f1a3 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1517,6 +1517,24 @@ config TARGET_LS1021ATWR select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI imply SCSI +config TARGET_PG_WCOM_SELI8 + bool "Support Hitachi-Powergrids SELI8 service unit card" + select ARCH_LS1021A + select ARCH_SUPPORT_PSCI + select BOARD_EARLY_INIT_F + select BOARD_LATE_INIT + select CPU_V7A + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select SYS_FSL_DDR + select FSL_DDR_INTERACTIVE + select VENDOR_KM + imply SCSI + help + Support for Hitachi-Powergrids SELI8 service unit card. + SELI8 is a QorIQ LS1021a based service unit card used + in XMC20 and FOX615 product families. + config TARGET_LS1021ATSN bool "Support ls1021atsn" select ARCH_LS1021A @@ -2036,6 +2054,7 @@ source "board/variscite/dart_6ul/Kconfig" source "board/vscom/baltos/Kconfig" source "board/phytium/durian/Kconfig" source "board/xen/xenguest_arm64/Kconfig" +source "board/keymile/Kconfig" source "arch/arm/Kconfig.debug" diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 858b79a..dbc71c0 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -399,6 +399,8 @@ dtb-$(CONFIG_ARCH_LS1021A) += ls1021a-qds-duart.dtb \ ls1021a-qds-lpuart.dtb \ ls1021a-twr-duart.dtb ls1021a-twr-lpuart.dtb \ ls1021a-iot-duart.dtb ls1021a-tsn.dtb +dtb-$(CONFIG_TARGET_PG_WCOM_SELI8) += ls1021a-pg-wcom-seli8.dtb + dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \ fsl-ls2080a-qds-42-x.dtb \ fsl-ls2080a-rdb.dtb \ diff --git a/arch/arm/dts/ls1021a-pg-wcom-seli8.dts b/arch/arm/dts/ls1021a-pg-wcom-seli8.dts new file mode 100644 index 0000000..e335188 --- /dev/null +++ b/arch/arm/dts/ls1021a-pg-wcom-seli8.dts @@ -0,0 +1,111 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2013-2015 Freescale Semiconductor, Inc. + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +/dts-v1/; +#include "ls1021a.dtsi" + +/ { + model = "Hitachi-Powergrids SELI8 Service Unit for XMC and FOX"; + + chosen { + stdout-path = &uart0; + }; +}; + +&enet0 { + status = "okay"; + tbi-handle = <&tbi0>; + phy-connection-type = "sgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&enet1 { + status = "okay"; + tbi-handle = <&tbi1>; + phy-connection-type = "sgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&enet2 { + phy-handle = <&debug_phy>; + phy-connection-type = "rgmii-id"; + status = "okay"; +}; + +&i2c0 { + status = "okay"; +}; + +&ifc { + #address-cells = <2>; + #size-cells = <1>; + /* NOR Flash on board */ + ranges = <0x0 0x0 0x60000000 0x04000000>; + status = "okay"; + + nor@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x4000000>; + bank-width = <2>; + device-width = <1>; + + partition@0 { + label = "rcw"; + reg = <0x0 0x20000>; + read-only; + }; + partition@20000 { + label = "qe"; + reg = <0x20000 0x20000>; + }; + partition@40000 { + label = "envred"; + reg = <0x40000 0x20000>; + }; + partition@60000 { + label = "env"; + reg = <0x60000 0x20000>; + }; + partition@100000 { + label = "u-boot"; + reg = <0x100000 0x100000>; + }; + partition@200000 { + label = "ubi0"; + reg = <0x200000 0x3E00000>; + }; + }; +}; + +&mdio0 { + debug_phy: ethernet-phy@11 { + reg = <0x11>; + }; + + tbi0: tbi-phy@0xb { + reg = <0xb>; + device_type = "tbi-phy"; + }; +}; + +&mdio1 { + tbi1: tbi-phy@0xd { + reg = <0xd>; + device_type = "tbi-phy"; + }; +}; + +&uart0 { + status = "okay"; +}; diff --git a/board/keymile/Kconfig b/board/keymile/Kconfig index e590690..965a537 100644 --- a/board/keymile/Kconfig +++ b/board/keymile/Kconfig @@ -20,8 +20,8 @@ config KM_PNVRAM config KM_PHRAM hex "Physical RAM" - default 0x17F000 if ARM - default 0x100000 if PPC + default 0x17F000 if ARM && !ARCH_LS1021A + default 0x100000 if PPC || ARCH_LS1021A depends on !ARCH_SOCFPGA help Start address of the physical RAM, which is the mounted /var folder. @@ -30,13 +30,14 @@ config KM_RESERVED_PRAM hex "Reserved RAM" default 0x801000 if ARCH_KIRKWOOD default 0x0 if MPC83xx - default 0x1000 if MPC85xx + default 0x1000 if MPC85xx || ARCH_LS1021A depends on !ARCH_SOCFPGA help Reserved physical RAM area at the end of memory for special purposes. config KM_CRAMFS_ADDR hex "CRAMFS Address" + default 0x83000000 if ARCH_LS1021A default 0x3000000 depends on !ARCH_SOCFPGA help @@ -44,16 +45,25 @@ config KM_CRAMFS_ADDR config KM_KERNEL_ADDR hex "Kernel Load Address" + default 0x82000000 if ARCH_LS1021A default 0x2000000 help Address where to load Linux kernel in RAM. config KM_FDT_ADDR hex "FDT Load Address" + default 0x82FC0000 if ARCH_LS1021A default 0x2FC0000 help Address where to load flattened device tree in RAM. +config SYS_PAX_BASE + hex "PAX IFC Base Address" + default 0x78000000 + depends on ARCH_LS1021A + help + IFC Base Address for PAXx FPGA. + config KM_CONSOLE_TTY string "KM Console" default "ttyS0" @@ -69,9 +79,9 @@ config KM_DEF_NETDEV config KM_COMMON_ETH_INIT bool "Common Ethernet Initialization" default y if ARCH_KIRKWOOD || MPC83xx - default n if MPC85xx || ARCH_SOCFPGA + default n if MPC85xx || ARCH_SOCFPGA || ARCH_LS1021A help - Use the Ethernet initialization implemented in common code, which + Use the Ethernet initialization implemented in common code that detects if a Piggy board is present. config PIGGY_MAC_ADDRESS_OFFSET @@ -90,7 +100,7 @@ config KM_MVEXTSW_ADDR config KM_IVM_BUS int "IVM I2C Bus" default 0 if ARCH_SOCFPGA - default 1 if ARCH_KIRKWOOD || MPC85xx + default 1 if ARCH_KIRKWOOD || MPC85xx || ARCH_LS1021A default 2 if MPC83xx help Identifier number of I2C bus, where the inventory EEPROM is connected to. @@ -116,6 +126,7 @@ config SYS_IVM_EEPROM_PAGE_LEN source "board/keymile/km83xx/Kconfig" source "board/keymile/kmp204x/Kconfig" source "board/keymile/km_arm/Kconfig" +source "board/keymile/pg-wcom-ls102xa/Kconfig" endmenu diff --git a/board/keymile/common/ivm.c b/board/keymile/common/ivm.c index e989bf6..48817cb 100644 --- a/board/keymile/common/ivm.c +++ b/board/keymile/common/ivm.c @@ -306,11 +306,7 @@ static int ivm_populate_env(unsigned char *buf, int len, int mac_address_offset) return 0; page2 = &buf[CONFIG_SYS_IVM_EEPROM_PAGE_LEN * 2]; - if (!IS_ENABLED(CONFIG_KMTEGR1)) { - /* if an offset is defined, add it */ - process_mac(valbuf, page2, mac_address_offset, true); - env_set((char *)"ethaddr", (char *)valbuf); - } else { + if (IS_ENABLED(CONFIG_KMTEGR1)) { /* KMTEGR1 has a special setup. eth0 has no connection to the * outside and gets an locally administred MAC address, eth1 is * the debug interface and gets the official MAC address from @@ -320,6 +316,19 @@ static int ivm_populate_env(unsigned char *buf, int len, int mac_address_offset) env_set((char *)"ethaddr", (char *)valbuf); process_mac(valbuf, page2, mac_address_offset, true); env_set((char *)"eth1addr", (char *)valbuf); + } else if (IS_ENABLED(CONFIG_ARCH_LS1021A)) { + /* LS102xA has 1xRGMII for debug connection and + * 2xSGMII for back-plane mgmt connection + */ + process_mac(valbuf, page2, 1, true); + env_set((char *)"ethaddr", (char *)valbuf); + process_mac(valbuf, page2, 2, true); + env_set((char *)"eth1addr", (char *)valbuf); + process_mac(valbuf, page2, mac_address_offset, true); + env_set((char *)"eth2addr", (char *)valbuf); + } else { + process_mac(valbuf, page2, mac_address_offset, true); + env_set((char *)"ethaddr", (char *)valbuf); } return 0; diff --git a/board/keymile/pg-wcom-ls102xa/Kconfig b/board/keymile/pg-wcom-ls102xa/Kconfig new file mode 100644 index 0000000..15c009d --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/Kconfig @@ -0,0 +1,19 @@ +if TARGET_PG_WCOM_SELI8 + +config SYS_BOARD + default "pg-wcom-ls102xa" + +config SYS_VENDOR + default "keymile" + +config SYS_SOC + default "ls102xa" + +config SYS_CONFIG_NAME + default "pg-wcom-seli8" + +config BOARD_SPECIFIC_OPTIONS + def_bool y + imply FS_CRAMFS + +endif diff --git a/board/keymile/pg-wcom-ls102xa/MAINTAINERS b/board/keymile/pg-wcom-ls102xa/MAINTAINERS new file mode 100644 index 0000000..e1bc90a --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/MAINTAINERS @@ -0,0 +1,10 @@ +Hitachi Power Grids LS102XA BOARD +M: Aleksandar Gerasimovski <aleksandar.gerasimovski(a)hitachi-powergrids.com> +M: Rainer Boschung <rainer.boschung(a)hitachi-powergrids.com> +M: Matteo Ghidoni <matteo.ghidoni(a)hitachi-powergrids.com> +S: Maintained +F: board/keymile/pg-wcom-ls102xa/ +F: include/configs/km/pg-wcom-ls102xa.h +F: include/configs/pg-wcom-seli8.h +F: configs/pg_wcom_seli8_defconfig +F: arch/arm/dts/ls1021a-pg-wcom-seli8.dts diff --git a/board/keymile/pg-wcom-ls102xa/Makefile b/board/keymile/pg-wcom-ls102xa/Makefile new file mode 100644 index 0000000..229b0c2 --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/Makefile @@ -0,0 +1,11 @@ +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright 2021 Hitachi Power Grids. All rights reserved. +# + +obj-y += pg-wcom-ls102xa.o ddr.o +obj-y += ../common/common.o ../common/ivm.o ../common/qrio.o +obj-$(CONFIG_LAYERSCAPE_NS_ACCESS) += +../../freescale/common/ns_access.o +obj-$(CONFIG_LS102XA_STREAM_ID) += +../../freescale/common/ls102xa_stream_id.o +obj-$(CONFIG_ID_EEPROM) += ../../freescale/common/sys_eeprom.o diff --git a/board/keymile/pg-wcom-ls102xa/ddr.c b/board/keymile/pg-wcom-ls102xa/ddr.c new file mode 100644 index 0000000..6023573 --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/ddr.c @@ -0,0 +1,90 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +#include <common.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> +#include <asm/io.h> +#include <asm/arch/clock.h> +#include <asm/arch/ls102xa_soc.h> + +DECLARE_GLOBAL_DATA_PTR; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + if (ctrl_num > 1) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + + // 1/2 DRAM cycle (should be increased in case of ADDR/CMD heavily loaded than the clock) + popts->clk_adjust = 0x4; + popts->write_data_delay = 0x4; + // wr leveling start value for lane 0 + popts->wrlvl_start = 0x5; + // wr leveling start values for lanes 1-3 (lane 4 not there) + popts->wrlvl_ctl_2 = 0x05050500; + // 32-bit DRAM, no need to set start values for lanes we do not have (5-8) + popts->wrlvl_ctl_3 = 0x0; + popts->cpo_override = 0x1f; + + /* force DDR bus width to 32 bits */ + popts->data_bus_width = 1; + popts->otf_burst_chop_en = 0; + popts->burst_length = DDR_BL8; + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 1; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * Rtt and Rtt_WR override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + popts->cswl_override = DDR_CSWL_CS0; + + /* optimize cpo for erratum A-009942 */ + popts->cpo_sample = 0x58; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); } + +int fsl_initdram(void) +{ + phys_size_t dram_size; + + puts("Initializing DDR....using SPD\n"); + dram_size = fsl_ddr_sdram(); + + erratum_a008850_post(); + + gd->ram_size = dram_size; + + return 0; +} + +int dram_init_banksize(void) +{ + gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; + gd->bd->bi_dram[0].size = gd->ram_size; + + return 0; +} diff --git a/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c b/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c new file mode 100644 index 0000000..6b0e963 --- /dev/null +++ b/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c @@ -0,0 +1,160 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +#include <common.h> +#include <i2c.h> +#include <asm/io.h> +#include <asm/arch/immap_ls102xa.h> +#include <asm/arch/clock.h> +#include <asm/arch/fsl_serdes.h> +#include <asm/arch/ls102xa_devdis.h> +#include <asm/arch/ls102xa_soc.h> +#include <hwconfig.h> +#include <mmc.h> +#include <fsl_csu.h> +#include <fsl_esdhc.h> +#include <fsl_ifc.h> +#include <fsl_immap.h> +#include <netdev.h> +#include <fsl_mdio.h> +#include <tsec.h> +#include <fsl_sec.h> +#include <fsl_devdis.h> +#include <fsl_ddr.h> +#include <spl.h> +#include <fdt_support.h> +#include <fsl_qe.h> +#include <fsl_validate.h> + +#include "../common/common.h" +#include "../common/qrio.h" + +DECLARE_GLOBAL_DATA_PTR; + +static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN]; + +int checkboard(void) +{ + show_qrio(); + + return 0; +} + +int dram_init(void) +{ + return fsl_initdram(); +} + +int board_early_init_f(void) +{ + struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR; + struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR; + struct fsl_ifc ifc = {(void *)CONFIG_SYS_IFC_ADDR, (void *)NULL}; + + /* Disable unused MCK1 */ + setbits_be32(&gur->ddrclkdr, 2); + + /* IFC Global Configuration */ + setbits_be32(&ifc.gregs->ifc_gcr, 12 << IFC_GCR_TBCTL_TRN_TIME_SHIFT); + setbits_be32(&ifc.gregs->ifc_ccr, IFC_CCR_CLK_DIV(3) | + IFC_CCR_INV_CLK_EN); + + /* clear BD & FR bits for BE BD's and frame data */ + clrbits_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR); + out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125); + + init_early_memctl_regs(); + + /* QRIO Configuration */ + qrio_uprstreq(UPREQ_CORE_RST); + + if (IS_ENABLED(CONFIG_TARGET_PG_WCOM_SELI8)) { + qrio_prstcfg(KM_LIU_RST, PRSTCFG_POWUP_UNIT_RST); + qrio_wdmask(KM_LIU_RST, true); + + qrio_prstcfg(KM_PAXK_RST, PRSTCFG_POWUP_UNIT_RST); + qrio_wdmask(KM_PAXK_RST, true); + + qrio_prstcfg(KM_DBG_ETH_RST, PRSTCFG_POWUP_UNIT_CORE_RST); + qrio_prst(KM_DBG_ETH_RST, false, false); + } + + i2c_deblock_gpio_cfg(); + + arch_soc_init(); + + return 0; +} + +int board_init(void) +{ + if (IS_ENABLED(CONFIG_SYS_FSL_ERRATUM_A010315)) + erratum_a010315(); + + fsl_serdes_init(); + + ls102xa_smmu_stream_id_init(); + + u_qe_init(); + + return 0; +} + +int board_late_init(void) +{ + return 0; +} + +int misc_init_r(void) +{ + if (IS_ENABLED(CONFIG_FSL_DEVICE_DISABLE)) + device_disable(devdis_tbl, ARRAY_SIZE(devdis_tbl)); + + ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN, + CONFIG_PIGGY_MAC_ADDRESS_OFFSET); + + return 0; +} + +int ft_board_setup(void *blob, struct bd_info *bd) { + ft_cpu_setup(blob, bd); + + if (IS_ENABLED(CONFIG_PCI)) + ft_pci_setup(blob, bd); + + return 0; +} + +u8 flash_read8(void *addr) +{ + return __raw_readb(addr + 1); +} + +void flash_write16(u16 val, void *addr) { + u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00)); + + __raw_writew(shftval, addr); +} + +u16 flash_read16(void *addr) +{ + u16 val = __raw_readw(addr); + + return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00); } + +int hush_init_var(void) +{ + ivm_analyze_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN); + return 0; +} + +int last_stage_init(void) +{ + set_km_env(); + return 0; +} diff --git a/configs/pg_wcom_seli8_defconfig b/configs/pg_wcom_seli8_defconfig new file mode 100644 index 0000000..60eb0e1 --- /dev/null +++ b/configs/pg_wcom_seli8_defconfig @@ -0,0 +1,65 @@ +CONFIG_ARM=y +CONFIG_TARGET_PG_WCOM_SELI8=y +CONFIG_SYS_TEXT_BASE=0x60100000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_KM_DEF_NETDEV="eth2" +CONFIG_KM_COMMON_ETH_INIT=y +CONFIG_PIGGY_MAC_ADDRESS_OFFSET=3 +CONFIG_SYS_MEMTEST_START=0x80000000 +CONFIG_SYS_MEMTEST_END=0x9fffffff +CONFIG_ENV_SIZE=0x20000 +CONFIG_ENV_SECT_SIZE=0x20000 +CONFIG_BOOTCOUNT_BOOTLIMIT=3 +CONFIG_SYS_BOOTCOUNT_ADDR=0x70000020 +CONFIG_DEFAULT_DEVICE_TREE="ls1021a-pg-wcom-seli8" +CONFIG_AHCI=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_BOOTDELAY=3 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0" +CONFIG_SILENT_CONSOLE=y +CONFIG_MISC_INIT_R=y +CONFIG_LAST_STAGE_INIT=y +CONFIG_CMD_IMLS=y +CONFIG_CMD_GREPENV=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_NAND=y +CONFIG_CMD_NAND_TRIMFFS=y +CONFIG_CMD_CRAMFS=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nor0=60000000.nor,nand0=68000000.flash" +CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:128k(rcw),128k(qe),128k(envred),128k(env),512k(res),1m(u-boot),-(ubi0);68000000.flash:-(ubi1)" +CONFIG_CMD_UBI=y +CONFIG_OF_CONTROL=y +CONFIG_ENV_IS_IN_FLASH=y +CONFIG_ENV_ADDR=0x60060000 +CONFIG_ENV_ADDR_REDUND=0x60040000 +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y +CONFIG_DM=y +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_SYS_FSL_DDR3=y +# CONFIG_MMC is not set +CONFIG_MTD=y +CONFIG_MTD_NOR_FLASH=y +CONFIG_FLASH_CFI_DRIVER=y +CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y +CONFIG_FLASH_CFI_MTD=y +CONFIG_SYS_FLASH_CFI=y +CONFIG_MTD_RAW_NAND=y +CONFIG_PHY_MARVELL=y +CONFIG_PHY_FIXED=y +CONFIG_DM_ETH=y +CONFIG_DM_MDIO=y +CONFIG_PHY_GIGE=y +CONFIG_MII=y +CONFIG_TSEC_ENET=y +CONFIG_SPECIFY_CONSOLE_INDEX=y +CONFIG_DM_SERIAL=y +CONFIG_SYS_NS16550=y diff --git a/include/configs/km/pg-wcom-ls102xa.h b/include/configs/km/pg-wcom-ls102xa.h new file mode 100644 index 0000000..e0f015e --- /dev/null +++ b/include/configs/km/pg-wcom-ls102xa.h @@ -0,0 +1,297 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +#ifndef __CONFIG_PG_WCOM_LS102XA_H +#define __CONFIG_PG_WCOM_LS102XA_H + +#define CONFIG_SYS_FSL_CLK + +#define CONFIG_SKIP_LOWLEVEL_INIT + +/* include common defines/options for all Keymile boards */ #include +"keymile-common.h" + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024) + +#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE + +#define CONFIG_SYS_CLK_FREQ 66666666 +/* + * Take into account default implementation where DDR_FDBK_MULTI is +consider as + * configured for DDR_PLL = 2*MEM_PLL_RAT. + * In our case DDR_FDBK_MULTI is 2, means DDR_PLL = MEM_PLL_RAT. + */ +#define CONFIG_DDR_CLK_FREQ (100000000 >> 1) + +#define PHYS_SDRAM 0x80000000 +#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 4 + +#define CONFIG_DDR_SPD + +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x54 + +/* + * IFC Definitions + */ +/* NOR Flash Definitions */ +#define CONFIG_FSL_IFC +#define CONFIG_SYS_FLASH_BASE 0x60000000 +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE + +#define CONFIG_SYS_NOR0_CSPR_EXT (0x0) +#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_TE | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(64 * 1024 * 1024) + +#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_AVD_TGL_PGM_EN | \ + CSOR_NOR_ADM_SHIFT(0x4) | \ + CSOR_NOR_NOR_MODE_AYSNC_NOR | \ + CSOR_NOR_TRHZ_20 | \ + CSOR_NOR_BCTLD) +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x1) | \ + FTIM0_NOR_TEADC(0x7) | \ + FTIM0_NOR_TAVDS(0x0) | \ + FTIM0_NOR_TEAHC(0x1)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1) | \ + FTIM1_NOR_TRAD_NOR(0x21) | \ + FTIM1_NOR_TSEQRAD_NOR(0x21)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x1) | \ + FTIM2_NOR_TCH(0x1) | \ + FTIM2_NOR_TWPH(0x6) | \ + FTIM2_NOR_TWP(0xb)) +#define CONFIG_SYS_NOR_FTIM3 0 + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS } + +#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS +#define CONFIG_SYS_WRITE_SWAPPED_DATA + +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 + +/* NAND Flash Definitions */ +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_BASE 0x68000000 +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE + +#define CONFIG_SYS_NAND_CSPR_EXT (0x0) +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE) | \ + CSPR_PORT_SIZE_8 | \ + CSPR_TE | \ + CSPR_MSEL_NAND | \ + CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN \ + | CSOR_NAND_ECC_DEC_EN \ + | CSOR_NAND_ECC_MODE_4 \ + | CSOR_NAND_RAL_3 \ + | CSOR_NAND_PGS_2K \ + | CSOR_NAND_SPRZ_64 \ + | CSOR_NAND_PB(64) \ + | CSOR_NAND_TRHZ_40 \ + | CSOR_NAND_BCTLD) + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x3) | \ + FTIM0_NAND_TWP(0x8) | \ + FTIM0_NAND_TWCHT(0x3) | \ + FTIM0_NAND_TWH(0x5)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x1e) | \ + FTIM1_NAND_TWBE(0x1e) | \ + FTIM1_NAND_TRR(0x6) | \ + FTIM1_NAND_TRP(0x8)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x9) | \ + FTIM2_NAND_TREH(0x5) | \ + FTIM2_NAND_TWHRE(0x3c)) +#define CONFIG_SYS_NAND_FTIM3 (FTIM3_NAND_TWW(0x1e)) + +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 + +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +/* QRIO FPGA Definitions */ +#define CONFIG_SYS_QRIO_BASE 0x70000000 +#define CONFIG_SYS_QRIO_BASE_PHYS CONFIG_SYS_QRIO_BASE + +#define CONFIG_SYS_CSPR2_EXT (0x00) +#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE) | \ + CSPR_PORT_SIZE_8 | \ + CSPR_TE | \ + CSPR_MSEL_GPCM | \ + CSPR_V) +#define CONFIG_SYS_AMASK2 IFC_AMASK(64 * 1024) +#define CONFIG_SYS_CSOR2 (CSOR_GPCM_ADM_SHIFT(0x4) | \ + CSOR_GPCM_TRHZ_20 | \ + CSOR_GPCM_BCTLD) +#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x2) | \ + FTIM0_GPCM_TEADC(0x8) | \ + FTIM0_GPCM_TEAHC(0x2)) +#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x2) | \ + FTIM1_GPCM_TRAD(0x6)) +#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x1) | \ + FTIM2_GPCM_TCH(0x1) | \ + FTIM2_GPCM_TWP(0x7)) +#define CONFIG_SYS_CS2_FTIM3 0x04000000 + +/* + * Serial Port + */ +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + +/* + * I2C + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_INIT_BOARD +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ +#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ +#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ + +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_MAX_HOPS 1 +#define CONFIG_SYS_NUM_I2C_BUSES 3 +#define I2C_MUX_PCA_ADDR 0x70 +#define I2C_MUX_CH_DEFAULT 0x0 +#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \ + {1, {I2C_NULL_HOP} }, \ + } + +/* + * eTSEC + */ +#ifdef CONFIG_TSEC_ENET +#define CONFIG_ETHPRIME "ethernet@2d90000" +#endif + +#define CONFIG_LAYERSCAPE_NS_ACCESS +#define CONFIG_SMP_PEN_ADDR 0x01ee0200 +#define COUNTER_FREQUENCY 12500000 + +#define CONFIG_HWCONFIG +#define HWCONFIG_BUFFER_SIZE 256 +#define CONFIG_FSL_DEVICE_DISABLE + +/* + * Miscellaneous configurable options + */ + +#define CONFIG_SYS_LOAD_ADDR 0x82000000 + +#define CONFIG_LS102XA_STREAM_ID + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define +CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_LEN 0x100000 /* 1Mbyte */ +#define CONFIG_SYS_QE_FW_ADDR 0x60020000 + +#define CONFIG_SYS_BOOTCOUNT_BE + +/* + * Environment + */ + +#define CONFIG_ENV_TOTAL_SIZE 0x40000 +#define ENV_DEL_ADDR 0x60040000 /* direct for newenv */ + +#define CONFIG_ENV_OVERWRITE +#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ +#define CONFIG_KM_DEF_ENV +#endif + +#ifndef CONFIG_KM_DEF_BOOT_ARGS_CPU +#define CONFIG_KM_DEF_BOOT_ARGS_CPU "" +#endif + +#define CONFIG_KM_DEF_ENV_CPU \ + "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \ + "cramfsloadfdt=" \ + "cramfsload ${fdt_addr_r} " \ + "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \ + "u-boot=" CONFIG_HOSTNAME "/u-boot.bin\0" \ + "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize} && " \ + "erase " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize} && " \ + "cp.b ${load_addr_r} " \ + __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize} && " \ + "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize}\0" \ + "update-nor=protect off " __stringify(CONFIG_SYS_FLASH_BASE) \ + " +${filesize} && " \ + "erase " __stringify(CONFIG_SYS_FLASH_BASE) \ + " +${filesize} && " \ + "cp.b ${load_addr_r} " \ + __stringify(CONFIG_SYS_FLASH_BASE) " ${filesize} && " \ + "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +" __stringify(CONFIG_SYS_MONITOR_LEN)"\0" \ + "set_fdthigh=true\0" \ + "checkfdt=true\0" \ + "" + +#define CONFIG_KM_NEW_ENV \ + "newenv=protect off " __stringify(ENV_DEL_ADDR) \ + " +" __stringify(CONFIG_ENV_TOTAL_SIZE) " && " \ + "erase " __stringify(ENV_DEL_ADDR) \ + " +" __stringify(CONFIG_ENV_TOTAL_SIZE) " && " \ + "protect on " __stringify(ENV_DEL_ADDR) \ + " +" __stringify(CONFIG_ENV_TOTAL_SIZE) "\0" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_KM_NEW_ENV \ + CONFIG_KM_DEF_ENV \ + "EEprom_ivm=pca9547:70:9\0" \ + "" + +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Increase map for Linux */ + +#endif diff --git a/include/configs/pg-wcom-seli8.h b/include/configs/pg-wcom-seli8.h new file mode 100644 index 0000000..9a7669c --- /dev/null +++ b/include/configs/pg-wcom-seli8.h @@ -0,0 +1,45 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 Hitachi Power Grids. All rights reserved. + */ + +#ifndef __CONFIG_PG_WCOM_SELI8_H +#define __CONFIG_PG_WCOM_SELI8_H + +#define CONFIG_HOSTNAME "SELI8" + +#define CONFIG_KM_UBI_PARTITION_NAME_BOOT "ubi0" +#define CONFIG_KM_UBI_PARTITION_NAME_APP "ubi1" + +/* PAXK FPGA Definitions */ +#define CONFIG_SYS_CSPR3_EXT (0x00) +#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(CONFIG_SYS_PAX_BASE) | \ + CSPR_PORT_SIZE_8 | \ + CSPR_MSEL_GPCM | \ + CSPR_V) +#define CONFIG_SYS_AMASK3 IFC_AMASK(64 * 1024) +#define CONFIG_SYS_CSOR3 (CSOR_GPCM_ADM_SHIFT(0x4) | \ + CSOR_GPCM_TRHZ_40) +#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x6) | \ + FTIM0_GPCM_TEADC(0x7) | \ + FTIM0_GPCM_TEAHC(0x2)) +#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x2) | \ + FTIM1_GPCM_TRAD(0x12)) +#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x3) | \ + FTIM2_GPCM_TCH(0x1) | \ + FTIM2_GPCM_TWP(0x12)) +#define CONFIG_SYS_CS3_FTIM3 0x04000000 + +/* PRST */ +#define KM_LIU_RST 0 +#define KM_PAXK_RST 1 +#define KM_DBG_ETH_RST 15 + +/* QRIO GPIOs used for deblocking */ +#define KM_I2C_DEBLOCK_PORT QRIO_GPIO_A +#define KM_I2C_DEBLOCK_SCL 20 +#define KM_I2C_DEBLOCK_SDA 21 + +#include "km/pg-wcom-ls102xa.h" + +#endif /* __CONFIG_PG_WCOM_SELI8_H */ -- 1.8.3.1 -----Original Message----- From: Tom Rini <trini(a)konsulko.com> Sent: Donnerstag, 4. Februar 2021 19:10 To: Aleksandar Gerasimovski <aleksandar.gerasimovski(a)hitachi-powergrids.com> Cc: Priyanka Jain (OSS) <priyanka.jain(a)oss.nxp.com>; Priyanka Jain <priyanka.jain(a)nxp.com>; u-boot(a)lists.denx.de; Valentin Longchamp <valentin.longchamp(a)hitachi-powergrids.com>; Holger Brunck <holger.brunck(a)hitachi-powergrids.com>; Rainer Boschung <rainer.boschung(a)hitachi-powergrids.com>; Matteo Ghidoni <matteo.ghidoni(a)hitachi-powergrids.com> Subject: Re: [PATCH v3 4/4] board/km: add support for seli8 design based on nxp ls102x On Thu, Feb 04, 2021 at 03:28:59PM +0000, Aleksandar Gerasimovski wrote: > The SELI8 design is a new tdm service unit card for Hitachi-Powergrids > XMC and FOX product lines. > > It is based on NXP LS1021 SoC and it provides following interfaces: > - IFC interface for NOR, NAND and external FPGA's > - 1 x RGMII ETH for debug purposes > - 2 x SGMII ETH for management communication via back-plane > - 1 x uQE HDLC for management communication via back-plane > - 1 x I2C for peripheral devices > - 1 x SPI for peripheral devices > - 1 x UART for debug logging > > It is foreseen that the design will be later re-used for another XMC > and FOX service cards with similar SoC requirements. > > Signed-off-by: Rainer Boschung > <rainer.boschung(a)hitachi-powergrids.com> > Signed-off-by: Matteo Ghidoni <matteo.ghidoni(a)hitachi-powergrids.com> > Signed-off-by: Aleksandar Gerasimovski > <aleksandar.gerasimovski(a)hitachi-powergrids.com> [snip] > +#ifndef __ASSEMBLY__ > +void set_sda(int state); > +void set_scl(int state); > +int get_sda(void); > +int get_scl(void); > +#endif As a pre-req clean-up, please put these in a proper header file under board/keymile/common/ and #include as needed and not in the per-board config.h files. [snip] > +/* > + * Environment > + */ > + > +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT > +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) Environment is handled via Kconfig, please correct this and audit the config.h file for other things that are handled via Kconfig now. Thanks! -- Tom

1 0

[PATCH v4] arm: fsl: common: Improve NXP VID driver PMBus support
by Wasim Khan 05 Feb '21

05 Feb '21

From: Stephen Carlson <stcarlso(a)linux.microsoft.com> This patch adds support for more PMBus compatible devices to the NXP drivers for its QorIQ family devices. At runtime, the voltage regulator is queried over I2C, and the required voltage multiplier determined. This change supports the DIRECT and LINEAR PMBus voltage reporting modes. Previously, the driver only supported a few specific devices such as the IR36021 and LTC3882, so this change allows the QorIQ series to be used with a much larger variety of core voltage regulator devices. checkpatch warning "Use if (IS_DEFINED (...))" was ignored to maintain consistency with the existing code. Signed-off-by: Stephen Carlson <stcarlso(a)linux.microsoft.com> Signed-off-by: Wasim Khan <wasim.khan(a)nxp.com> Tested-by: Wasim Khan <wasim.khan(a)nxp.com> --- Changes in v4: - Included upstream commit ada19fd2 - compilation fix for platforms using IR36021 - read_voltage() fix for devices using INA220 - compilation fix for ls1088 - removed soc_get_fuse_vid() support for ls1028 board/freescale/common/Kconfig | 27 +- board/freescale/common/vid.c | 816 ++++++++++++------------------ board/freescale/common/vid.h | 11 +- board/freescale/ls1088a/ls1088a.c | 40 ++ board/freescale/ls2080a/ls2080a.c | 49 ++ board/freescale/lx2160a/lx2160a.c | 42 ++ include/configs/ls1088aqds.h | 6 - include/configs/ls1088ardb.h | 8 +- 8 files changed, 480 insertions(+), 519 deletions(-) diff --git a/board/freescale/common/Kconfig b/board/freescale/common/Kconfig index 1b1fd69cb2..17db755951 100644 --- a/board/freescale/common/Kconfig +++ b/board/freescale/common/Kconfig @@ -21,18 +21,37 @@ config CMD_ESBC_VALIDATE esbc_validate - validate signature using RSA verification esbc_halt - put the core in spin loop (Secure Boot Only) +config VID + depends on DM_I2C + bool "Enable Freescale VID" + help + This option enables setting core voltage based on individual + values saved in SoC fuses. + config VOL_MONITOR_LTC3882_READ depends on VID bool "Enable the LTC3882 voltage monitor read" - default n help This option enables LTC3882 voltage monitor read - functionality. It is used by common VID driver. + functionality. It is used by the common VID driver. config VOL_MONITOR_LTC3882_SET depends on VID bool "Enable the LTC3882 voltage monitor set" - default n help This option enables LTC3882 voltage monitor set - functionality. It is used by common VID driver. + functionality. It is used by the common VID driver. + +config VOL_MONITOR_ISL68233_READ + depends on VID + bool "Enable the ISL68233 voltage monitor read" + help + This option enables ISL68233 voltage monitor read + functionality. It is used by the common VID driver. + +config VOL_MONITOR_ISL68233_SET + depends on VID + bool "Enable the ISL68233 voltage monitor set" + help + This option enables ISL68233 voltage monitor set + functionality. It is used by the common VID driver. diff --git a/board/freescale/common/vid.c b/board/freescale/common/vid.c index 2617f61520..14bef19aea 100644 --- a/board/freescale/common/vid.c +++ b/board/freescale/common/vid.c @@ -2,6 +2,7 @@ /* * Copyright 2014 Freescale Semiconductor, Inc. * Copyright 2020 NXP + * Copyright 2020 Stephen Carlson <stcarlso(a)linux.microsoft.com> */ #include <common.h> @@ -21,14 +22,22 @@ #include <linux/delay.h> #include "vid.h" +/* Voltages are generally handled in mV to keep them as integers */ +#define MV_PER_V 1000 + +/* + * Select the channel on the I2C mux (on some NXP boards) that contains + * the voltage regulator to use for VID. Return 0 for success or nonzero + * for failure. + */ int __weak i2c_multiplexer_select_vid_channel(u8 channel) { return 0; } /* - * Compensate for a board specific voltage drop between regulator and SoC - * return a value in mV + * Compensate for a board specific voltage drop between regulator and SoC. + * Returns the voltage offset in mV. */ int __weak board_vdd_drop_compensation(void) { @@ -36,13 +45,90 @@ int __weak board_vdd_drop_compensation(void) } /* - * Board specific settings for specific voltage value + * Performs any board specific adjustments after the VID voltage has been + * set. Return 0 for success or nonzero for failure. */ int __weak board_adjust_vdd(int vdd) { return 0; } +/* + * Processor specific method of converting the fuse value read from VID + * registers into the core voltage to supply. Return the voltage in mV. + */ +u16 __weak soc_get_fuse_vid(int vid_index) +{ + /* Default VDD for Layerscape Chassis 1 devices */ + static const u16 vdd[32] = { + 0, /* unused */ + 9875, /* 0.9875V */ + 9750, + 9625, + 9500, + 9375, + 9250, + 9125, + 9000, + 8875, + 8750, + 8625, + 8500, + 8375, + 8250, + 8125, + 10000, /* 1.0000V */ + 10125, + 10250, + 10375, + 10500, + 10625, + 10750, + 10875, + 11000, + 0, /* reserved */ + }; + return vdd[vid_index]; +} + +#ifdef CONFIG_DM_I2C +#define DEVICE_HANDLE_T struct udevice * + +#ifndef I2C_VOL_MONITOR_BUS +#define I2C_VOL_MONITOR_BUS 0 +#endif + +/* If DM is in use, retrieve the udevice chip for the specified bus number */ +static int vid_get_device(int address, DEVICE_HANDLE_T *dev) +{ + int ret = i2c_get_chip_for_busnum(I2C_VOL_MONITOR_BUS, address, 1, dev); + + if (ret) + printf("VID: Bus %d has no device with address 0x%02X\n", + I2C_VOL_MONITOR_BUS, address); + return ret; +} + +#define I2C_READ(dev, register, data, length) \ + dm_i2c_read(dev, register, data, length) +#define I2C_WRITE(dev, register, data, length) \ + dm_i2c_write(dev, register, data, length) +#else +#define DEVICE_HANDLE_T int + +/* If DM is not in use, I2C addresses are passed directly */ +static int vid_get_device(int address, DEVICE_HANDLE_T *dev) +{ + *dev = address; + return 0; +} + +#define I2C_READ(dev, register, data, length) \ + i2c_read(dev, register, 1, data, length) +#define I2C_WRITE(dev, register, data, length) \ + i2c_write(dev, register, 1, data, length) +#endif + #if defined(CONFIG_VOL_MONITOR_IR36021_SET) || \ defined(CONFIG_VOL_MONITOR_IR36021_READ) /* @@ -60,30 +146,22 @@ int __weak board_adjust_vdd(int vdd) */ static int find_ir_chip_on_i2c(void) { - int i2caddress; - int ret; - u8 byte; - int i; + int i2caddress, ret, i; + u8 mfrID; const int ir_i2c_addr[] = {0x38, 0x08, 0x09}; -#ifdef CONFIG_DM_I2C - struct udevice *dev; -#endif + DEVICE_HANDLE_T dev; /* Check all the address */ for (i = 0; i < (sizeof(ir_i2c_addr)/sizeof(ir_i2c_addr[0])); i++) { i2caddress = ir_i2c_addr[i]; -#ifndef CONFIG_DM_I2C - ret = i2c_read(i2caddress, - IR36021_MFR_ID_OFFSET, 1, (void *)&byte, - sizeof(byte)); -#else - ret = i2c_get_chip_for_busnum(0, i2caddress, 1, &dev); - if (!ret) - ret = dm_i2c_read(dev, IR36021_MFR_ID_OFFSET, - (void *)&byte, sizeof(byte)); -#endif - if ((ret >= 0) && (byte == IR36021_MFR_ID)) - return i2caddress; + ret = vid_get_device(i2caddress, &dev); + if (!ret) { + ret = I2C_READ(dev, IR36021_MFR_ID_OFFSET, + (void *)&mfrID, sizeof(mfrID)); + /* If manufacturer ID matches the IR36021 */ + if (!ret && mfrID == IR36021_MFR_ID) + return i2caddress; + } } return -1; } @@ -117,35 +195,33 @@ static int read_voltage_from_INA220(int i2caddress) int i, ret, voltage_read = 0; u16 vol_mon; u8 buf[2]; -#ifdef CONFIG_DM_I2C - struct udevice *dev; -#endif + DEVICE_HANDLE_T dev; + + /* Open device handle */ + ret = vid_get_device(i2caddress, &dev); + if (ret) + return ret; for (i = 0; i < NUM_READINGS; i++) { -#ifndef CONFIG_DM_I2C - ret = i2c_read(I2C_VOL_MONITOR_ADDR, - I2C_VOL_MONITOR_BUS_V_OFFSET, 1, - (void *)&buf, 2); -#else - ret = i2c_get_chip_for_busnum(0, I2C_VOL_MONITOR_ADDR, 1, &dev); - if (!ret) - ret = dm_i2c_read(dev, I2C_VOL_MONITOR_BUS_V_OFFSET, - (void *)&buf, 2); -#endif + ret = I2C_READ(dev, I2C_VOL_MONITOR_BUS_V_OFFSET, + (void *)&buf[0], sizeof(buf)); if (ret) { printf("VID: failed to read core voltage\n"); return ret; } + vol_mon = (buf[0] << 8) | buf[1]; if (vol_mon & I2C_VOL_MONITOR_BUS_V_OVF) { printf("VID: Core voltage sensor error\n"); return -1; } + debug("VID: bus voltage reads 0x%04x\n", vol_mon); /* LSB = 4mv */ voltage_read += (vol_mon >> I2C_VOL_MONITOR_BUS_V_SHIFT) * 4; udelay(WAIT_FOR_ADC); } + /* calculate the average */ voltage_read /= NUM_READINGS; @@ -153,30 +229,25 @@ static int read_voltage_from_INA220(int i2caddress) } #endif -/* read voltage from IR */ #ifdef CONFIG_VOL_MONITOR_IR36021_READ +/* read voltage from IR */ static int read_voltage_from_IR(int i2caddress) { int i, ret, voltage_read = 0; u16 vol_mon; u8 buf; -#ifdef CONFIG_DM_I2C - struct udevice *dev; -#endif + DEVICE_HANDLE_T dev; + + /* Open device handle */ + ret = vid_get_device(i2caddress, &dev); + if (ret) + return ret; for (i = 0; i < NUM_READINGS; i++) { -#ifndef CONFIG_DM_I2C - ret = i2c_read(i2caddress, - IR36021_LOOP1_VOUT_OFFSET, - 1, (void *)&buf, 1); -#else - ret = i2c_get_chip_for_busnum(0, i2caddress, 1, &dev); - if (!ret) - ret = dm_i2c_read(dev, IR36021_LOOP1_VOUT_OFFSET, - (void *)&buf, 1); -#endif + ret = I2C_READ(dev, IR36021_LOOP1_VOUT_OFFSET, (void *)&buf, + sizeof(buf)); if (ret) { - printf("VID: failed to read vcpu\n"); + printf("VID: failed to read core voltage\n"); return ret; } vol_mon = buf; @@ -188,7 +259,7 @@ static int read_voltage_from_IR(int i2caddress) /* Resolution is 1/128V. We scale up here to get 1/128mV * and divide at the end */ - voltage_read += vol_mon * 1000; + voltage_read += vol_mon * MV_PER_V; udelay(WAIT_FOR_ADC); } /* Scale down to the real mV as IR resolution is 1/128V, rounding up */ @@ -206,49 +277,94 @@ static int read_voltage_from_IR(int i2caddress) } #endif -#ifdef CONFIG_VOL_MONITOR_LTC3882_READ -/* read the current value of the LTC Regulator Voltage */ -static int read_voltage_from_LTC(int i2caddress) -{ - int ret, vcode = 0; - u8 chan = PWM_CHANNEL0; +#if defined(CONFIG_VOL_MONITOR_ISL68233_READ) || \ + defined(CONFIG_VOL_MONITOR_LTC3882_READ) || \ + defined(CONFIG_VOL_MONITOR_ISL68233_SET) || \ + defined(CONFIG_VOL_MONITOR_LTC3882_SET) -#ifndef CONFIG_DM_I2C - /* select the PAGE 0 using PMBus commands PAGE for VDD*/ - ret = i2c_write(I2C_VOL_MONITOR_ADDR, - PMBUS_CMD_PAGE, 1, &chan, 1); -#else - struct udevice *dev; +/* + * The message displayed if the VOUT exponent causes a resolution + * worse than 1.0 V (if exponent is >= 0). + */ +#define VOUT_WARNING "VID: VOUT_MODE exponent has resolution worse than 1 V!\n" - ret = i2c_get_chip_for_busnum(0, I2C_VOL_MONITOR_ADDR, 1, &dev); - if (!ret) - ret = dm_i2c_write(dev, PMBUS_CMD_PAGE, &chan, 1); -#endif +/* Checks the PMBus voltage monitor for the format used for voltage values */ +static int get_pmbus_multiplier(DEVICE_HANDLE_T dev) +{ + u8 mode; + int exponent, multiplier, ret; + + ret = I2C_READ(dev, PMBUS_CMD_VOUT_MODE, &mode, sizeof(mode)); if (ret) { - printf("VID: failed to select VDD Page 0\n"); + printf("VID: unable to determine voltage multiplier\n"); + return 1; + } + + /* Upper 3 bits is mode, lower 5 bits is exponent */ + exponent = (int)mode & 0x1F; + mode >>= 5; + switch (mode) { + case 0: + /* Linear, 5 bit twos component exponent */ + if (exponent & 0x10) { + multiplier = 1 << (16 - (exponent & 0xF)); + } else { + /* If exponent is >= 0, then resolution is 1 V! */ + printf(VOUT_WARNING); + multiplier = 1; + } + break; + case 1: + /* VID code identifier */ + printf("VID: custom VID codes are not supported\n"); + multiplier = MV_PER_V; + break; + default: + /* Direct, in mV */ + multiplier = MV_PER_V; + break; + } + + debug("VID: calculated multiplier is %d\n", multiplier); + return multiplier; +} +#endif + +#if defined(CONFIG_VOL_MONITOR_ISL68233_READ) || \ + defined(CONFIG_VOL_MONITOR_LTC3882_READ) +static int read_voltage_from_pmbus(int i2caddress) +{ + int ret, multiplier, vout; + u8 channel = PWM_CHANNEL0; + u16 vcode; + DEVICE_HANDLE_T dev; + + /* Open device handle */ + ret = vid_get_device(i2caddress, &dev); + if (ret) return ret; - } -#ifndef CONFIG_DM_I2C - /*read the output voltage using PMBus command READ_VOUT*/ - ret = i2c_read(I2C_VOL_MONITOR_ADDR, - PMBUS_CMD_READ_VOUT, 1, (void *)&vcode, 2); -#else - ret = dm_i2c_read(dev, PMBUS_CMD_READ_VOUT, (void *)&vcode, 2); + /* Select the right page */ + ret = I2C_WRITE(dev, PMBUS_CMD_PAGE, &channel, sizeof(channel)); if (ret) { - printf("VID: failed to read the volatge\n"); + printf("VID: failed to select VDD page %d\n", channel); return ret; } -#endif + + /* VOUT is little endian */ + ret = I2C_READ(dev, PMBUS_CMD_READ_VOUT, (void *)&vcode, sizeof(vcode)); if (ret) { - printf("VID: failed to read the volatge\n"); + printf("VID: failed to read core voltage\n"); return ret; } - /* Scale down to the real mV as LTC resolution is 1/4096V,rounding up */ - vcode = DIV_ROUND_UP(vcode * 1000, 4096); - - return vcode; + /* Scale down to the real mV */ + multiplier = get_pmbus_multiplier(dev); + vout = (int)vcode; + /* Multiplier 1000 (direct mode) requires no change to convert */ + if (multiplier != MV_PER_V) + vout = DIV_ROUND_UP(vout * MV_PER_V, multiplier); + return vout - board_vdd_drop_compensation(); } #endif @@ -256,13 +372,14 @@ static int read_voltage(int i2caddress) { int voltage_read; #ifdef CONFIG_VOL_MONITOR_INA220 - voltage_read = read_voltage_from_INA220(i2caddress); + voltage_read = read_voltage_from_INA220(I2C_VOL_MONITOR_ADDR); #elif defined CONFIG_VOL_MONITOR_IR36021_READ voltage_read = read_voltage_from_IR(i2caddress); -#elif defined CONFIG_VOL_MONITOR_LTC3882_READ - voltage_read = read_voltage_from_LTC(i2caddress); +#elif defined(CONFIG_VOL_MONITOR_ISL68233_READ) || \ + defined(CONFIG_VOL_MONITOR_LTC3882_READ) + voltage_read = read_voltage_from_pmbus(i2caddress); #else - return -1; + voltage_read = -1; #endif return voltage_read; } @@ -300,7 +417,7 @@ static int wait_for_new_voltage(int vdd, int i2caddress) } /* - * this function keeps reading the voltage until it is stable or until the + * Blocks and reads the VID voltage until it stabilizes, or the * timeout expires */ static int wait_for_voltage_stable(int i2caddress) @@ -310,9 +427,9 @@ static int wait_for_voltage_stable(int i2caddress) vdd = read_voltage(i2caddress); udelay(NUM_READINGS * WAIT_FOR_ADC); - /* wait until voltage is stable */ vdd_current = read_voltage(i2caddress); - /* The maximum timeout is + /* + * The maximum timeout is * MAX_LOOP_WAIT_VOL_STABLE * NUM_READINGS * WAIT_FOR_ADC */ for (timeout = MAX_LOOP_WAIT_VOL_STABLE; @@ -327,12 +444,18 @@ static int wait_for_voltage_stable(int i2caddress) return vdd_current; } -/* Set the voltage to the IR chip */ +/* Sets the VID voltage using the IR36021 */ static int set_voltage_to_IR(int i2caddress, int vdd) { int wait, vdd_last; int ret; u8 vid; + DEVICE_HANDLE_T dev; + + /* Open device handle */ + ret = vid_get_device(i2caddress, &dev); + if (ret) + return ret; /* Compensate for a board specific voltage drop between regulator and * SoC before converting into an IR VID value @@ -344,20 +467,10 @@ static int set_voltage_to_IR(int i2caddress, int vdd) vid = DIV_ROUND_UP(vdd - 245, 5); #endif -#ifndef CONFIG_DM_I2C - ret = i2c_write(i2caddress, IR36021_LOOP1_MANUAL_ID_OFFSET, - 1, (void *)&vid, sizeof(vid)); -#else - struct udevice *dev; - - ret = i2c_get_chip_for_busnum(0, i2caddress, 1, &dev); - if (!ret) - ret = dm_i2c_write(dev, IR36021_LOOP1_MANUAL_ID_OFFSET, - (void *)&vid, sizeof(vid)); - -#endif + ret = I2C_WRITE(dev, IR36021_LOOP1_MANUAL_ID_OFFSET, (void *)&vid, + sizeof(vid)); if (ret) { - printf("VID: failed to write VID\n"); + printf("VID: failed to write new voltage\n"); return -1; } wait = wait_for_new_voltage(vdd, i2caddress); @@ -371,81 +484,59 @@ static int set_voltage_to_IR(int i2caddress, int vdd) debug("VID: Current voltage is %d mV\n", vdd_last); return vdd_last; } - #endif -#ifdef CONFIG_VOL_MONITOR_LTC3882_SET -/* this function sets the VDD and returns the value set */ -static int set_voltage_to_LTC(int i2caddress, int vdd) +#if defined(CONFIG_VOL_MONITOR_ISL68233_SET) || \ + defined(CONFIG_VOL_MONITOR_LTC3882_SET) +static int set_voltage_to_pmbus(int i2caddress, int vdd) { int ret, vdd_last, vdd_target = vdd; - int count = 100, temp = 0; + int count = MAX_LOOP_WAIT_NEW_VOL, temp = 0, multiplier; unsigned char value; - /* Scale up to the LTC resolution is 1/4096V */ - vdd = (vdd * 4096) / 1000; + /* The data to be sent with the PMBus command PAGE_PLUS_WRITE */ + u8 buffer[5] = { 0x04, PWM_CHANNEL0, PMBUS_CMD_VOUT_COMMAND, 0, 0 }; + DEVICE_HANDLE_T dev; - /* 5-byte buffer which needs to be sent following the - * PMBus command PAGE_PLUS_WRITE. - */ - u8 buff[5] = {0x04, PWM_CHANNEL0, PMBUS_CMD_VOUT_COMMAND, - vdd & 0xFF, (vdd & 0xFF00) >> 8}; + /* Open device handle */ + ret = vid_get_device(i2caddress, &dev); + if (ret) + return ret; + + /* Scale up to the proper value for the VOUT command, little endian */ + multiplier = get_pmbus_multiplier(dev); + vdd += board_vdd_drop_compensation(); + if (multiplier != MV_PER_V) + vdd = DIV_ROUND_UP(vdd * multiplier, MV_PER_V); + buffer[3] = vdd & 0xFF; + buffer[4] = (vdd & 0xFF00) >> 8; - /* Write the desired voltage code to the regulator */ -#ifndef CONFIG_DM_I2C /* Check write protect state */ - ret = i2c_read(I2C_VOL_MONITOR_ADDR, - PMBUS_CMD_WRITE_PROTECT, 1, - (void *)&value, sizeof(value)); + ret = I2C_READ(dev, PMBUS_CMD_WRITE_PROTECT, (void *)&value, + sizeof(value)); if (ret) goto exit; if (value != EN_WRITE_ALL_CMD) { value = EN_WRITE_ALL_CMD; - ret = i2c_write(I2C_VOL_MONITOR_ADDR, - PMBUS_CMD_WRITE_PROTECT, 1, + ret = I2C_WRITE(dev, PMBUS_CMD_WRITE_PROTECT, (void *)&value, sizeof(value)); if (ret) goto exit; } - ret = i2c_write(I2C_VOL_MONITOR_ADDR, - PMBUS_CMD_PAGE_PLUS_WRITE, 1, - (void *)&buff, sizeof(buff)); -#else - struct udevice *dev; - - ret = i2c_get_chip_for_busnum(0, I2C_VOL_MONITOR_ADDR, 1, &dev); - if (!ret) { - /* Check write protect state */ - ret = dm_i2c_read(dev, - PMBUS_CMD_WRITE_PROTECT, - (void *)&value, sizeof(value)); - if (ret) - goto exit; - - if (value != EN_WRITE_ALL_CMD) { - value = EN_WRITE_ALL_CMD; - ret = dm_i2c_write(dev, - PMBUS_CMD_WRITE_PROTECT, - (void *)&value, sizeof(value)); - if (ret) - goto exit; - } - - ret = dm_i2c_write(dev, PMBUS_CMD_PAGE_PLUS_WRITE, - (void *)&buff, sizeof(buff)); - } -#endif -exit: + /* Write the desired voltage code to the regulator */ + ret = I2C_WRITE(dev, PMBUS_CMD_PAGE_PLUS_WRITE, (void *)&buffer[0], + sizeof(buffer)); if (ret) { - printf("VID: I2C failed to write to the volatge regulator\n"); + printf("VID: I2C failed to write to the voltage regulator\n"); return -1; } - /* Wait for the volatge to get to the desired value */ +exit: + /* Wait for the voltage to get to the desired value */ do { - vdd_last = read_voltage_from_LTC(i2caddress); + vdd_last = read_voltage_from_pmbus(i2caddress); if (vdd_last < 0) { printf("VID: Couldn't read sensor abort VID adjust\n"); return -1; @@ -464,325 +555,80 @@ static int set_voltage(int i2caddress, int vdd) #ifdef CONFIG_VOL_MONITOR_IR36021_SET vdd_last = set_voltage_to_IR(i2caddress, vdd); -#elif defined CONFIG_VOL_MONITOR_LTC3882_SET - vdd_last = set_voltage_to_LTC(i2caddress, vdd); +#elif defined(CONFIG_VOL_MONITOR_ISL68233_SET) || \ + defined(CONFIG_VOL_MONITOR_LTC3882_SET) + vdd_last = set_voltage_to_pmbus(i2caddress, vdd); #else #error Specific voltage monitor must be defined #endif return vdd_last; } -#ifdef CONFIG_FSL_LSCH3 int adjust_vdd(ulong vdd_override) { int re_enable = disable_interrupts(); +#if defined(CONFIG_FSL_LSCH2) || defined(CONFIG_FSL_LSCH3) struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); - u32 fusesr; -#if defined(CONFIG_VOL_MONITOR_IR36021_SET) || \ - defined(CONFIG_VOL_MONITOR_IR36021_READ) - u8 vid, buf; #else - u8 vid; + ccsr_gur_t __iomem *gur = + (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); #endif - int vdd_target, vdd_current, vdd_last; - int ret, i2caddress = 0; + u8 vid; + u32 fusesr; + int vdd_current, vdd_last, vdd_target; + int ret, i2caddress = I2C_VOL_MONITOR_ADDR; unsigned long vdd_string_override; char *vdd_string; -#if defined(CONFIG_ARCH_LX2160A) || defined(CONFIG_ARCH_LX2162A) - static const u16 vdd[32] = { - 8250, - 7875, - 7750, - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 8000, - 8125, - 8250, - 0, /* reserved */ - 8500, - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - }; -#else -#ifdef CONFIG_ARCH_LS1088A - static const uint16_t vdd[32] = { - 10250, - 9875, - 9750, - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 9000, - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 10000, /* 1.0000V */ - 10125, - 10250, - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - }; -#else - static const uint16_t vdd[32] = { - 10500, - 0, /* reserved */ - 9750, - 0, /* reserved */ - 9500, - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 9000, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 10000, /* 1.0000V */ - 0, /* reserved */ - 10250, - 0, /* reserved */ - 10500, - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - 0, /* reserved */ - }; -#endif -#endif - struct vdd_drive { - u8 vid; - unsigned voltage; - }; - - ret = i2c_multiplexer_select_vid_channel(I2C_MUX_CH_VOL_MONITOR); - if (ret) { - debug("VID: I2C failed to switch channel\n"); - ret = -1; - goto exit; - } #if defined(CONFIG_VOL_MONITOR_IR36021_SET) || \ defined(CONFIG_VOL_MONITOR_IR36021_READ) - ret = find_ir_chip_on_i2c(); - if (ret < 0) { - printf("VID: Could not find voltage regulator on I2C.\n"); - ret = -1; - goto exit; - } else { - i2caddress = ret; - debug("VID: IR Chip found on I2C address 0x%02x\n", i2caddress); - } - - /* check IR chip work on Intel mode*/ -#ifndef CONFIG_DM_I2C - ret = i2c_read(i2caddress, - IR36021_INTEL_MODE_OOFSET, - 1, (void *)&buf, 1); -#else - struct udevice *dev; - - ret = i2c_get_chip_for_busnum(0, i2caddress, 1, &dev); - if (!ret) - ret = dm_i2c_read(dev, IR36021_INTEL_MODE_OOFSET, - (void *)&buf, 1); -#endif - if (ret) { - printf("VID: failed to read IR chip mode.\n"); - ret = -1; - goto exit; - } - - if ((buf & IR36021_MODE_MASK) != IR36021_INTEL_MODE) { - printf("VID: IR Chip is not used in Intel mode.\n"); - ret = -1; - goto exit; - } + u8 buf; + DEVICE_HANDLE_T dev; #endif - /* get the voltage ID from fuse status register */ + /* + * VID is used according to the table below + * --------------------------------------- + * | DA_V | + * |-------------------------------------| + * | 5b00000 | 5b00001-5b11110 | 5b11111 | + * ---------------+---------+-----------------+---------| + * | D | 5b00000 | NO VID | VID = DA_V | NO VID | + * | A |----------+---------+-----------------+---------| + * | _ | 5b00001 |VID = | VID = |VID = | + * | V | ~ | DA_V_ALT| DA_V_ALT | DA_A_VLT| + * | _ | 5b11110 | | | | + * | A |----------+---------+-----------------+---------| + * | L | 5b11111 | No VID | VID = DA_V | NO VID | + * | T | | | | | + * ------------------------------------------------------ + */ +#if defined(CONFIG_FSL_LSCH3) fusesr = in_le32(&gur->dcfg_fusesr); vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_ALTVID_SHIFT) & - FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK; - if ((vid == 0) || (vid == FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK)) { + FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK; + if (vid == 0 || vid == FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK) { vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_VID_SHIFT) & - FSL_CHASSIS3_DCFG_FUSESR_VID_MASK; - } - vdd_target = vdd[vid]; - - /* check override variable for overriding VDD */ - vdd_string = env_get(CONFIG_VID_FLS_ENV); - if (vdd_override == 0 && vdd_string && - !strict_strtoul(vdd_string, 10, &vdd_string_override)) - vdd_override = vdd_string_override; - - if (vdd_override >= VDD_MV_MIN && vdd_override <= VDD_MV_MAX) { - vdd_target = vdd_override * 10; /* convert to 1/10 mV */ - debug("VDD override is %lu\n", vdd_override); - } else if (vdd_override != 0) { - printf("Invalid value.\n"); - } - - /* divide and round up by 10 to get a value in mV */ - vdd_target = DIV_ROUND_UP(vdd_target, 10); - if (vdd_target == 0) { - debug("VID: VID not used\n"); - ret = 0; - goto exit; - } else if (vdd_target < VDD_MV_MIN || vdd_target > VDD_MV_MAX) { - /* Check vdd_target is in valid range */ - printf("VID: Target VID %d mV is not in range.\n", - vdd_target); - ret = -1; - goto exit; - } else { - debug("VID: vid = %d mV\n", vdd_target); + FSL_CHASSIS3_DCFG_FUSESR_VID_MASK; } - - /* - * Read voltage monitor to check real voltage. - */ - vdd_last = read_voltage(i2caddress); - if (vdd_last < 0) { - printf("VID: Couldn't read sensor abort VID adjustment\n"); - ret = -1; - goto exit; +#elif defined(CONFIG_FSL_LSCH2) + fusesr = in_be32(&gur->dcfg_fusesr); + vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_ALTVID_SHIFT) & + FSL_CHASSIS2_DCFG_FUSESR_ALTVID_MASK; + if (vid == 0 || vid == FSL_CHASSIS2_DCFG_FUSESR_ALTVID_MASK) { + vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_VID_SHIFT) & + FSL_CHASSIS2_DCFG_FUSESR_VID_MASK; } - vdd_current = vdd_last; - debug("VID: Core voltage is currently at %d mV\n", vdd_last); - -#ifdef CONFIG_VOL_MONITOR_LTC3882_SET - /* Set the target voltage */ - vdd_last = vdd_current = set_voltage(i2caddress, vdd_target); #else - /* - * Adjust voltage to at or one step above target. - * As measurements are less precise than setting the values - * we may run through dummy steps that cancel each other - * when stepping up and then down. - */ - while (vdd_last > 0 && - vdd_last < vdd_target) { - vdd_current += IR_VDD_STEP_UP; - vdd_last = set_voltage(i2caddress, vdd_current); - } - while (vdd_last > 0 && - vdd_last > vdd_target + (IR_VDD_STEP_DOWN - 1)) { - vdd_current -= IR_VDD_STEP_DOWN; - vdd_last = set_voltage(i2caddress, vdd_current); + fusesr = in_be32(&gur->dcfg_fusesr); + vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) & + FSL_CORENET_DCFG_FUSESR_ALTVID_MASK; + if (vid == 0 || vid == FSL_CORENET_DCFG_FUSESR_ALTVID_MASK) { + vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_VID_SHIFT) & + FSL_CORENET_DCFG_FUSESR_VID_MASK; } - #endif - if (board_adjust_vdd(vdd_target) < 0) { - ret = -1; - goto exit; - } - - if (vdd_last > 0) - printf("VID: Core voltage after adjustment is at %d mV\n", - vdd_last); - else - ret = -1; -exit: - if (re_enable) - enable_interrupts(); - i2c_multiplexer_select_vid_channel(I2C_MUX_CH_DEFAULT); - return ret; -} -#else /* !CONFIG_FSL_LSCH3 */ -int adjust_vdd(ulong vdd_override) -{ - int re_enable = disable_interrupts(); -#if defined(CONFIG_FSL_LSCH2) - struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); -#else - ccsr_gur_t __iomem *gur = - (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); -#endif - u32 fusesr; - u8 vid, buf; - int vdd_target, vdd_current, vdd_last; - int ret, i2caddress; - unsigned long vdd_string_override; - char *vdd_string; - static const uint16_t vdd[32] = { - 0, /* unused */ - 9875, /* 0.9875V */ - 9750, - 9625, - 9500, - 9375, - 9250, - 9125, - 9000, - 8875, - 8750, - 8625, - 8500, - 8375, - 8250, - 8125, - 10000, /* 1.0000V */ - 10125, - 10250, - 10375, - 10500, - 10625, - 10750, - 10875, - 11000, - 0, /* reserved */ - }; - struct vdd_drive { - u8 vid; - unsigned voltage; - }; + vdd_target = soc_get_fuse_vid((int)vid); ret = i2c_multiplexer_select_vid_channel(I2C_MUX_CH_VOL_MONITOR); if (ret) { @@ -790,6 +636,7 @@ int adjust_vdd(ulong vdd_override) ret = -1; goto exit; } + #if defined(CONFIG_VOL_MONITOR_IR36021_SET) || \ defined(CONFIG_VOL_MONITOR_IR36021_READ) ret = find_ir_chip_on_i2c(); @@ -802,19 +649,13 @@ int adjust_vdd(ulong vdd_override) debug("VID: IR Chip found on I2C address 0x%02x\n", i2caddress); } - /* check IR chip work on Intel mode*/ -#ifndef CONFIG_DM_I2C - ret = i2c_read(i2caddress, - IR36021_INTEL_MODE_OOFSET, - 1, (void *)&buf, 1); -#else - struct udevice *dev; + ret = vid_get_device(i2caddress, &dev); + if (ret) + return ret; - ret = i2c_get_chip_for_busnum(0, i2caddress, 1, &dev); - if (!ret) - ret = dm_i2c_read(dev, IR36021_INTEL_MODE_OOFSET, - (void *)&buf, 1); -#endif + /* check IR chip work on Intel mode */ + ret = I2C_READ(dev, IR36021_INTEL_MODE_OFFSET, (void *)&buf, + sizeof(buf)); if (ret) { printf("VID: failed to read IR chip mode.\n"); ret = -1; @@ -827,52 +668,18 @@ int adjust_vdd(ulong vdd_override) } #endif - /* get the voltage ID from fuse status register */ - fusesr = in_be32(&gur->dcfg_fusesr); - /* - * VID is used according to the table below - * --------------------------------------- - * | DA_V | - * |-------------------------------------| - * | 5b00000 | 5b00001-5b11110 | 5b11111 | - * ---------------+---------+-----------------+---------| - * | D | 5b00000 | NO VID | VID = DA_V | NO VID | - * | A |----------+---------+-----------------+---------| - * | _ | 5b00001 |VID = | VID = |VID = | - * | V | ~ | DA_V_ALT| DA_V_ALT | DA_A_VLT| - * | _ | 5b11110 | | | | - * | A |----------+---------+-----------------+---------| - * | L | 5b11111 | No VID | VID = DA_V | NO VID | - * | T | | | | | - * ------------------------------------------------------ - */ -#ifdef CONFIG_FSL_LSCH2 - vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_ALTVID_SHIFT) & - FSL_CHASSIS2_DCFG_FUSESR_ALTVID_MASK; - if ((vid == 0) || (vid == FSL_CHASSIS2_DCFG_FUSESR_ALTVID_MASK)) { - vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_VID_SHIFT) & - FSL_CHASSIS2_DCFG_FUSESR_VID_MASK; - } -#else - vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) & - FSL_CORENET_DCFG_FUSESR_ALTVID_MASK; - if ((vid == 0) || (vid == FSL_CORENET_DCFG_FUSESR_ALTVID_MASK)) { - vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_VID_SHIFT) & - FSL_CORENET_DCFG_FUSESR_VID_MASK; - } -#endif - vdd_target = vdd[vid]; - /* check override variable for overriding VDD */ vdd_string = env_get(CONFIG_VID_FLS_ENV); + debug("VID: Initial VDD value is %d mV\n", + DIV_ROUND_UP(vdd_target, 10)); if (vdd_override == 0 && vdd_string && !strict_strtoul(vdd_string, 10, &vdd_string_override)) vdd_override = vdd_string_override; if (vdd_override >= VDD_MV_MIN && vdd_override <= VDD_MV_MAX) { vdd_target = vdd_override * 10; /* convert to 1/10 mV */ - debug("VDD override is %lu\n", vdd_override); + debug("VID: VDD override is %lu\n", vdd_override); } else if (vdd_override != 0) { - printf("Invalid value.\n"); + printf("VID: Invalid VDD value.\n"); } if (vdd_target == 0) { debug("VID: VID not used\n"); @@ -895,6 +702,13 @@ int adjust_vdd(ulong vdd_override) } vdd_current = vdd_last; debug("VID: Core voltage is currently at %d mV\n", vdd_last); + +#if defined(CONFIG_VOL_MONITOR_LTC3882_SET) || \ + defined(CONFIG_VOL_MONITOR_ISL68233_SET) + /* Set the target voltage */ + vdd_current = set_voltage(i2caddress, vdd_target); + vdd_last = vdd_current; +#else /* * Adjust voltage to at or one step above target. * As measurements are less precise than setting the values @@ -911,6 +725,13 @@ int adjust_vdd(ulong vdd_override) vdd_current -= IR_VDD_STEP_DOWN; vdd_last = set_voltage(i2caddress, vdd_current); } +#endif + + /* Board specific adjustments */ + if (board_adjust_vdd(vdd_target) < 0) { + ret = -1; + goto exit; + } if (vdd_last > 0) printf("VID: Core voltage after adjustment is at %d mV\n", @@ -925,11 +746,10 @@ exit: return ret; } -#endif static int print_vdd(void) { - int vdd_last, ret, i2caddress = 0; + int vdd_last, ret, i2caddress = I2C_VOL_MONITOR_ADDR; ret = i2c_multiplexer_select_vid_channel(I2C_MUX_CH_VOL_MONITOR); if (ret) { diff --git a/board/freescale/common/vid.h b/board/freescale/common/vid.h index 5bbaecace4..b34c080b4b 100644 --- a/board/freescale/common/vid.h +++ b/board/freescale/common/vid.h @@ -7,16 +7,17 @@ #ifndef __VID_H_ #define __VID_H_ +/* IR36021 command codes */ #define IR36021_LOOP1_MANUAL_ID_OFFSET 0x6A #define IR36021_LOOP1_VOUT_OFFSET 0x9A #define IR36021_MFR_ID_OFFSET 0x92 #define IR36021_MFR_ID 0x43 -#define IR36021_INTEL_MODE_OOFSET 0x14 +#define IR36021_INTEL_MODE_OFFSET 0x14 #define IR36021_MODE_MASK 0x20 #define IR36021_INTEL_MODE 0x00 #define IR36021_AMD_MODE 0x20 -/* step the IR regulator in 5mV increments */ +/* Step the IR regulator in 5mV increments */ #define IR_VDD_STEP_DOWN 5 #define IR_VDD_STEP_UP 5 @@ -50,15 +51,16 @@ #define VDD_MV_MAX 925 #endif -#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) || \ -defined(CONFIG_TARGET_LX2160ARDB) /* PM Bus commands code for LTC3882*/ #define PWM_CHANNEL0 0x0 #define PMBUS_CMD_PAGE 0x0 #define PMBUS_CMD_READ_VOUT 0x8B +#define PMBUS_CMD_VOUT_MODE 0x20 #define PMBUS_CMD_VOUT_COMMAND 0x21 #define PMBUS_CMD_PAGE_PLUS_WRITE 0x05 +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) || \ +defined(CONFIG_TARGET_LX2160ARDB) /* Voltage monitor on channel 2*/ #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 #define I2C_VOL_MONITOR_BUS_V_OVF 0x1 @@ -68,5 +70,6 @@ defined(CONFIG_TARGET_LX2160ARDB) #endif int adjust_vdd(ulong vdd_override); +u16 soc_get_fuse_vid(int vid_index); #endif /* __VID_H_ */ diff --git a/board/freescale/ls1088a/ls1088a.c b/board/freescale/ls1088a/ls1088a.c index 5d19702a05..2dba62c524 100644 --- a/board/freescale/ls1088a/ls1088a.c +++ b/board/freescale/ls1088a/ls1088a.c @@ -185,6 +185,46 @@ int init_func_vid(void) return 0; } + +u16 soc_get_fuse_vid(int vid_index) +{ + static const u16 vdd[32] = { + 10250, + 9875, + 9750, + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 9000, + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 10000, /* 1.0000V */ + 10125, + 10250, + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + }; + + return vdd[vid_index]; +}; #endif int is_pb_board(void) diff --git a/board/freescale/ls2080a/ls2080a.c b/board/freescale/ls2080a/ls2080a.c index 62da2a7af1..d02e479e3b 100644 --- a/board/freescale/ls2080a/ls2080a.c +++ b/board/freescale/ls2080a/ls2080a.c @@ -50,6 +50,55 @@ void detail_board_ddr_info(void) #endif } +#if defined(CONFIG_ARCH_MISC_INIT) +int arch_misc_init(void) +{ + return 0; +} +#endif + +#ifdef CONFIG_VID +u16 soc_get_fuse_vid(int vid_index) +{ + static const u16 vdd[32] = { + 10500, + 0, /* reserved */ + 9750, + 0, /* reserved */ + 9500, + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 9000, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 10000, /* 1.0000V */ + 0, /* reserved */ + 10250, + 0, /* reserved */ + 10500, + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + }; + + return vdd[vid_index]; +}; +#endif + int board_eth_init(struct bd_info *bis) { int error = 0; diff --git a/board/freescale/lx2160a/lx2160a.c b/board/freescale/lx2160a/lx2160a.c index ea027bec56..5ac6d0e746 100644 --- a/board/freescale/lx2160a/lx2160a.c +++ b/board/freescale/lx2160a/lx2160a.c @@ -648,6 +648,48 @@ int misc_init_r(void) } #endif +#ifdef CONFIG_VID +u16 soc_get_fuse_vid(int vid_index) +{ + static const u16 vdd[32] = { + 8250, + 7875, + 7750, + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 8000, + 8125, + 8250, + 0, /* reserved */ + 8500, + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + 0, /* reserved */ + }; + + return vdd[vid_index]; +}; +#endif + #ifdef CONFIG_FSL_MC_ENET extern int fdt_fixup_board_phy(void *fdt); diff --git a/include/configs/ls1088aqds.h b/include/configs/ls1088aqds.h index b92ec14c69..a2b21c697f 100644 --- a/include/configs/ls1088aqds.h +++ b/include/configs/ls1088aqds.h @@ -326,12 +326,6 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_VOL_MONITOR_LTC3882_SET #define CONFIG_VOL_MONITOR_LTC3882_READ -/* PM Bus commands code for LTC3882*/ -#define PMBUS_CMD_PAGE 0x0 -#define PMBUS_CMD_READ_VOUT 0x8B -#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05 -#define PMBUS_CMD_VOUT_COMMAND 0x21 - #define PWM_CHANNEL0 0x0 /* diff --git a/include/configs/ls1088ardb.h b/include/configs/ls1088ardb.h index f59a9f5574..6f36dd417a 100644 --- a/include/configs/ls1088ardb.h +++ b/include/configs/ls1088ardb.h @@ -203,7 +203,7 @@ #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 -#define I2C_MUX_CH_VOL_MONITOR 0xA +#define I2C_MUX_CH_VOL_MONITOR 0xA /* Voltage monitor on channel 2*/ #define I2C_VOL_MONITOR_ADDR 0x63 #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 @@ -221,12 +221,6 @@ #define CONFIG_VOL_MONITOR_LTC3882_SET #define CONFIG_VOL_MONITOR_LTC3882_READ -/* PM Bus commands code for LTC3882*/ -#define PMBUS_CMD_PAGE 0x0 -#define PMBUS_CMD_READ_VOUT 0x8B -#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05 -#define PMBUS_CMD_VOUT_COMMAND 0x21 - #define PWM_CHANNEL0 0x0 /* -- 2.25.1

3 3

[HELP] binman: main.py: not found
by Buhrow, Simon 05 Feb '21

05 Feb '21

Hi, I´m doing my first steps with u-boot. But I can´t run `make all` successfully. I get the following error when running `make all`: ``` ./tools/binman/binman: 1: ./tools/binman/binman: main.py: not found Makefile:1024: recipe for target 'all' failed make: *** [all] Error 127 ``` I´ve downloaded u-boot-2021.01 and I´m working on Ubuntu 18.04.3 LTS in VirtualBox on a Win10 PC. The file `./tools/binman/main.py` does exist. So I´m not sure if there is any problem with symbolic links? Python 3.6.9 is installed. Running `sudo make all` throws the same error, that´s why I don´t think it´s a permission problem. Regards, Simon

1 0