February 2020 - U-Boot

RPI4: fail too boot with an initrd
by LABBE Corentin 18 Feb '20

18 Feb '20

Hello Since the inclusion of the "enable network support in RPi4 config" serie on uboot, I have started to work on adding the rpi4 in kernelCI. But I fail to succeed in using a kernel/dtb/ramdisk downloaded via tftp. Using booti I hit: [ 0.000000] Linux version 5.6.0-rc1-next-20200212 (clabbe@build2-bionic-1804) (gcc version 7.4.1 20181213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33b1edc85d4] (Linaro GCC 7.4-2019.02)) #66 SMP PREEMPT Wed Feb 12 10:14:20 UTC 2020 [ 0.000000] Machine model: Raspberry Pi 4 Model B [ 0.000000] earlycon: uart0 at MMIO32 0x00000000fe215040 (options '') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: reserved mem: failed to allocate memory for node 'linux,cma' [ 0.000000] cma: Failed to reserve 32 MiB [ 0.000000] Kernel panic - not syncing: Failed to allocate page table page [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.6.0-rc1-next-20200212 #66 [ 0.000000] Hardware name: Raspberry Pi 4 Model B (DT) [ 0.000000] Call trace: [ 0.000000] dump_backtrace+0x0/0x1a0 [ 0.000000] show_stack+0x14/0x20 [ 0.000000] dump_stack+0xbc/0x104 [ 0.000000] panic+0x16c/0x37c [ 0.000000] early_pgtable_alloc+0x30/0xa0 [ 0.000000] __create_pgd_mapping+0x36c/0x588 [ 0.000000] map_kernel_segment+0x70/0xa4 [ 0.000000] paging_init+0xf4/0x528 [ 0.000000] setup_arch+0x250/0x5d8 [ 0.000000] start_kernel+0x90/0x6d8 Since the same kernel boot with bootefi and that bootefi lack ramdisk address, I tried to add the address in the dtb via: fdt addr 0x02400000; fdt resize; fdt set /chosen linux,initrd-start 0x02700000; fdt set /chosen linux,initrd-end 0x10000000; bootefi 0x00080000 0x02400000 But with that, I get: initrd not fully accessible via the linear mapping -- please check your bootloader ... I have tried many different start/end address without any change. My last resort was to embed the rootfs in the kernel. But with the correct console=, the boot stop at: [ 1.373557] fe201000.serial: ttyAMA0 at MMIO 0xfe201000 (irq = 16, base_baud = 0) is a PL011 rev2 [ 1.382565] printk: console [ttyAMA0] enabled [ 1.391318] printk: bootconsole [uart0] disabled With the wrong console (ttyS0), the boot go up to start init which panic due to lack of console. Regards

5 8

[PATCH v3 0/3] Ethernet support for Raspberry Pi 4
by Andre Przywara 18 Feb '20

18 Feb '20

This series adds Ethernet support for the Raspberry Pi 4. The SoC includes a "Broadcom Genet v5 MAC" IP, connected as a proper platform device (no USB anymore!). Patch 1 provides a driver for that. There does not seem to be publicly available documentation, so this is based on the Linux driver, but stripped down to just provide what U-Boot needs. Patch 2 fixes up the RPi4 memory map to accommodate the MMIO area the MAC lives in, while patch 3 enables it in the respective defconfigs. This version fixes the nasty SError issue that showed when booting Linux. To see the changes as patches, refer to [1]. Please have a look and test it, I hope this helps to simplify development, as you spare the SD card and its slot from heavy swapping. Cheers, Andre. [1] https://github.com/apritzel/u-boot/commits/rpi4-eth-v3 Changelog v2 ... v3: - properly reset MAC in eth_probe() to avoid SError in Linux - disable RX DMA upon stopping the device Changelog v1 ... v2: - use native endianess functions when accessing MMIO registers - use dev_* DM wrappers for accessing devicetree data - round base and length for flush_dcache_range, plus a comment - check and round length for invalidate_cache_range - support RGMII_RXID PHY mode, to support mainline .dtb Amit Singh Tomar (3): net: Add support for Broadcom GENETv5 Ethernet controller rpi4: Update memory map to accommodate scb devices rpi4: Enable GENET Ethernet controller arch/arm/mach-bcm283x/init.c | 6 +- configs/rpi_4_32b_defconfig | 2 + configs/rpi_4_defconfig | 2 + configs/rpi_arm64_defconfig | 1 + drivers/net/Kconfig | 7 + drivers/net/Makefile | 1 + drivers/net/bcmgenet.c | 729 +++++++++++++++++++++++++++++++++++++++++++ 7 files changed, 745 insertions(+), 3 deletions(-) create mode 100644 drivers/net/bcmgenet.c -- 2.14.5

5 15

[PATCH v2] doc: add board documentation for stm32mp1
by Patrick Delaunay 18 Feb '20

18 Feb '20

Change plain test README to rst format and move this file in documentation directory. Signed-off-by: Patrick Delaunay <patrick.delaunay(a)st.com> Tested-by: Heinrich Schuchardt <xypron.glpk(a)gmx.de> Reviewed-by: Patrice Chotard <patrice.chotard(a)st.com> --- Hi, it is V2 for the previous patch after rebase (the last of the serie) http://patchwork.ozlabs.org/patch/1230241/ Patrick Changes in v2: - remove extra line at the end of the rst file - rebase after stm32 custodian pull request - update MAINTAINERS file for doc/board/st MAINTAINERS | 1 + board/st/stm32mp1/README | 520 +-------------------------------- doc/board/index.rst | 1 + doc/board/st/index.rst | 9 + doc/board/st/stm32mp1.rst | 598 ++++++++++++++++++++++++++++++++++++++ 5 files changed, 610 insertions(+), 519 deletions(-) create mode 100644 doc/board/st/index.rst create mode 100644 doc/board/st/stm32mp1.rst diff --git a/MAINTAINERS b/MAINTAINERS index 82e4159bec..4d297ae97f 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -345,6 +345,7 @@ L: uboot-stm32(a)st-md-mailman.stormreply.com (moderated for non-subscribers) T: git https://gitlab.denx.de/u-boot/custodians/u-boot-stm.git S: Maintained F: arch/arm/mach-stm32mp/ +F: doc/board/st/ F: drivers/adc/stm32-adc* F: drivers/clk/clk_stm32mp1.c F: drivers/gpio/stm32_gpio.c diff --git a/board/st/stm32mp1/README b/board/st/stm32mp1/README index 5d7465a8c8..8172d26a66 100644 --- a/board/st/stm32mp1/README +++ b/board/st/stm32mp1/README @@ -1,519 +1 @@ -SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause -# -# Copyright (C) 2018 STMicroelectronics - All Rights Reserved -# - -U-Boot on STMicroelectronics STM32MP15x -======================================= - -1. Summary -========== -This is a quick instruction for setup stm32mp1 boards. - -2. Supported devices -==================== -U-Boot supports STMP32MP15x SoCs: STM32MP157, STM32MP153 and STM32MP151 - -The STM32MP15x is a Cortex-A MPU aimed at various applications. -It features: -- Dual core Cortex-A7 application core (Single on STM32MP151) -- 2D/3D image composition with GPU (only on STM32MP157) -- Standard memories interface support -- Standard connectivity, widely inherited from the STM32 MCU family -- Comprehensive security support - -Everything is supported in Linux but U-Boot is limited to: -1. UART -2. SDCard/MMC controller (SDMMC) -3. NAND controller (FMC) -4. NOR controller (QSPI) -5. USB controller (OTG DWC2) -6. Ethernet controller - -And the necessary drivers -1. I2C -2. STPMIC1 (PMIC and regulator) -3. Clock, Reset, Sysreset -4. Fuse - -Currently the following boards are supported: -+ stm32mp157a-avenger96.dts -+ stm32mp157a-dk1.dts -+ stm32mp157c-dk2.dts -+ stm32mp157c-ed1.dts -+ stm32mp157c-ev1.dts - -3. Boot Sequences -================= - -BootRom => FSBL in SYSRAM => SSBL in DDR => OS (Linux Kernel) - -with FSBL = First Stage Bootloader - SSBL = Second Stage Bootloader - -3 boot configurations are supported: - -1) The "Trusted" boot chain (defconfig_file : stm32mp15_trusted_defconfig) - BootRom => FSBL = Trusted Firmware-A (TF-A) => SSBL = U-Boot - TF-A performs a full initialization of Secure peripherals and installs a - secure monitor. - U-Boot is running in normal world and uses TF-A monitor - to access to secure resources. - -2) The "Trusted" boot chain with OP-TEE - (defconfig_file : stm32mp15_optee_defconfig) - BootRom => FSBL = Trusted Firmware-A (TF-A) => SSBL = U-Boot - TF-A performs a full initialization of Secure peripherals and installs OP-TEE - from specific partitions (teeh, teed, teex). - U-Boot is running in normal world and uses OP-TEE monitor to access - to secure resources. - -3) The "Basic" boot chain (defconfig_file : stm32mp15_basic_defconfig) - BootRom => FSBL = U-Boot SPL => SSBL = U-Boot - SPL has limited security initialisation - U-Boot is running in secure mode and provide a secure monitor to the kernel - with only PSCI support (Power State Coordination Interface defined by ARM). - -All the STM32MP15x boards supported by U-Boot use the same generic board -stm32mp1 which support all the bootable devices. - -Each board is configurated only with the associated device tree. - -4. Device Tree Selection -======================== - -You need to select the appropriate device tree for your board, -the supported device trees for stm32mp157 are: - -+ ev1: eval board with pmic stpmic1 (ev1 = mother board + daughter ed1) - dts: stm32mp157c-ev1 - -+ ed1: daughter board with pmic stpmic1 - dts: stm32mp157c-ed1 - -+ dk1: Discovery board - dts: stm32mp157a-dk1 - -+ dk2: Discovery board = dk1 with a BT/WiFI combo and a DSI panel - dts: stm32mp157c-dk2 - -+ avenger96: Avenger96 board from Arrow Electronics - dts: stm32mp157a-avenger96 - -5. Build Procedure -================== - -1. Install required tools for U-Boot - - + install package needed in U-Boot makefile - (libssl-dev, swig, libpython-dev...) - + install ARMv7 toolchain for 32bit Cortex-A (from Linaro, - from SDK for STM32MP15x, or any crosstoolchains from your distribution) - -2. Set the cross compiler: - - # export CROSS_COMPILE=/path/to/toolchain/arm-linux-gnueabi- - (you can use any gcc cross compiler compatible with U-Boot) - -3. Select the output directory (optional) - - # export KBUILD_OUTPUT=/path/to/output - - for example: use one output directory for each configuration - # export KBUILD_OUTPUT=stm32mp15_trusted - # export KBUILD_OUTPUT=stm32mp15_optee - # export KBUILD_OUTPUT=stm32mp15_basic - - you can build outside of code directory: - # export KBUILD_OUTPUT=../build/stm32mp15_trusted - -4. Configure U-Boot: - - # make <defconfig_file> - - - For trusted boot mode : "stm32mp15_trusted_defconfig" - - For trusted with OP-TEE boot mode : "stm32mp15_optee_defconfig" - - For basic boot mode: "stm32mp15_basic_defconfig" - -5. Configure the device-tree and build the U-Boot image: - - # make DEVICE_TREE=<name> all - - example: - a) trusted boot on ev1 - # export KBUILD_OUTPUT=stm32mp15_trusted - # make stm32mp15_trusted_defconfig - # make DEVICE_TREE=stm32mp157c-ev1 all - - b) trusted with OP-TEE boot on dk2 - # export KBUILD_OUTPUT=stm32mp15_optee - # make stm32mp15_optee_defconfig - # make DEVICE_TREE=stm32mp157c-dk2 all - - c) basic boot on ev1 - # export KBUILD_OUTPUT=stm32mp15_basic - # make stm32mp15_basic_defconfig - # make DEVICE_TREE=stm32mp157c-ev1 all - - d) basic boot on ed1 - # export KBUILD_OUTPUT=stm32mp15_basic - # make stm32mp15_basic_defconfig - # make DEVICE_TREE=stm32mp157c-ed1 all - - e) basic boot on dk1 - # export KBUILD_OUTPUT=stm32mp15_basic - # make stm32mp15_basic_defconfig - # make DEVICE_TREE=stm32mp157a-dk1 all - - f) basic boot on avenger96 - # export KBUILD_OUTPUT=stm32mp15_basic - # make stm32mp15_basic_defconfig - # make DEVICE_TREE=stm32mp157a-avenger96 all - -6. Output files - - BootRom and TF-A expect binaries with STM32 image header - SPL expects file with U-Boot uImage header - - So in the output directory (selected by KBUILD_OUTPUT), - you can found the needed files: - - a) For Trusted boot (with or without OP-TEE) - + FSBL = tf-a.stm32 (provided by TF-A compilation) - + SSBL = u-boot.stm32 - - b) For Basic boot - + FSBL = spl/u-boot-spl.stm32 - + SSBL = u-boot.img - -6. Switch Setting for Boot Mode -=============================== - -You can select the boot mode, on the board with one switch : - -- on the daugther board ed1 with the switch SW1 : BOOT0, BOOT1, BOOT2 - - ----------------------------------- - Boot Mode BOOT2 BOOT1 BOOT0 - ----------------------------------- - Reserved 0 0 0 - NOR 0 0 1 - SD-Card 1 0 1 - eMMC 0 1 0 - NAND 0 1 1 - Recovery 1 1 0 - Recovery 0 0 0 - -- on board DK1/DK2 with the switch SW1 : BOOT0, BOOT2 - (BOOT1 forced to 0, NOR not supported) - - -------------------------- - Boot Mode BOOT2 BOOT0 - -------------------------- - Reserved 1 0 - SD-Card 1 1 - Recovery 0 0 - -- Boot mode of Avenger96 can be selected using switch S3 - - ----------------------------------- - Boot Mode BOOT2 BOOT1 BOOT0 - ----------------------------------- - Recovery 0 0 0 - NOR 0 0 1 - SD-Card 1 0 1 - eMMC 0 1 0 - NAND 0 1 1 - Reserved 1 0 0 - Recovery 1 1 0 - SD-Card 1 1 1 - -Recovery is a boot from serial link (UART/USB) and it is used with -STM32CubeProgrammer tool to load executable in RAM and to update the flash -devices available on the board (NOR/NAND/eMMC/SDCARD). -The communication between HOST and board is based on -- for UARTs : the uart protocol used with all MCU STM32 -- for USB : based on USB DFU 1.1 (without the ST extensions used on MCU STM32) - -7. Prepare an SDCard -=================== - -The minimal requirements for STMP32MP1 boot up to U-Boot are: -- GPT partitioning (with gdisk or with sgdisk) -- 2 fsbl partitions, named fsbl1 and fsbl2, size at least 256KiB -- one ssbl partition for U-Boot - -Then the minimal GPT partition is: - ----- ------- --------- -------------- - | Num | Name | Size | Content | - ----- ------- -------- --------------- - | 1 | fsbl1 | 256 KiB | TF-A or SPL | - | 2 | fsbl2 | 256 KiB | TF-A or SPL | - | 3 | ssbl | enought | U-Boot | - | * | - | - | Boot/Rootfs | - ----- ------- --------- -------------- - -(*) add bootable partition for extlinux.conf - following Generic Distribution - (doc/README.distro for use) - - according the used card reader select the block device - (/dev/sdx or /dev/mmcblk0) - in the next example I use /dev/mmcblk0 - -for example: with gpt table with 128 entries - - a) remove previous formatting - # sgdisk -o /dev/<SDCard dev> - - b) create minimal image - # sgdisk --resize-table=128 -a 1 \ - -n 1:34:545 -c 1:fsbl1 \ - -n 2:546:1057 -c 2:fsbl2 \ - -n 3:1058:5153 -c 3:ssbl \ - -p /dev/<SDCard dev> - - you can add other partitions for kernel - one partition rootfs for example: - -n 4:5154: -c 4:rootfs \ - - c) copy the FSBL (2 times) and SSBL file on the correct partition. - in this example in partition 1 to 3 - - for basic boot mode : <SDCard dev> = /dev/mmcblk0 - # dd if=u-boot-spl.stm32 of=/dev/mmcblk0p1 - # dd if=u-boot-spl.stm32 of=/dev/mmcblk0p2 - # dd if=u-boot.img of=/dev/mmcblk0p3 - - for trusted boot mode : - # dd if=tf-a.stm32 of=/dev/mmcblk0p1 - # dd if=tf-a.stm32 of=/dev/mmcblk0p2 - # dd if=u-boot.stm32 of=/dev/mmcblk0p3 - -To boot from SDCard, select BootPinMode = 1 0 1 and reset. - -8. Prepare eMMC -=============== -You can use U-Boot to copy binary in eMMC. - -In the next example, you need to boot from SDCARD and the images (u-boot-spl.stm32, u-boot.img) -are presents on SDCARD (mmc 0) in ext4 partition 4 (bootfs). - -To boot from SDCard, select BootPinMode = 1 0 1 and reset. - -Then you update the eMMC with the next U-Boot command : - -a) prepare GPT on eMMC, - example with 2 partitions, bootfs and roots: - - # setenv emmc_part "name=ssbl,size=2MiB;name=bootfs,type=linux,bootable,size=64MiB;name=rootfs,type=linux,size=512" - # gpt write mmc 1 ${emmc_part} - -b) copy SPL on eMMC on firts boot partition - (SPL max size is 256kB, with LBA 512, 0x200) - - # ext4load mmc 0:4 0xC0000000 u-boot-spl.stm32 - # mmc dev 1 - # mmc partconf 1 1 1 1 - # mmc write ${fileaddr} 0 200 - # mmc partconf 1 1 1 0 - -c) copy U-Boot in first GPT partition of eMMC - - # ext4load mmc 0:4 0xC0000000 u-boot.img - # mmc dev 1 - # part start mmc 1 1 partstart - # mmc write ${fileaddr} ${partstart} ${filesize} - -To boot from eMMC, select BootPinMode = 0 1 0 and reset. - -9. MAC Address -============== - -Please read doc/README.enetaddr for the implementation guidelines for mac id -usage. Basically, environment has precedence over board specific storage. - -For STMicroelectonics board, it is retrieved in STM32MP15x otp : -- OTP_57[31:0] = MAC_ADDR[31:0] -- OTP_58[15:0] = MAC_ADDR[47:32] - -To program a MAC address on virgin OTP words above, you can use the fuse command -on bank 0 to access to internal OTP: - - Prerequisite: check if a MAC address isn't yet programmed in OTP - - 1- check OTP: their value must be equal to 0 - - STM32MP> fuse sense 0 57 2 - Sensing bank 0: - Word 0x00000039: 00000000 00000000 - - 2- check environment variable - - STM32MP> env print ethaddr - ## Error: "ethaddr" not defined - - Example to set mac address "12:34:56:78:9a:bc" - - 1- Write OTP - STM32MP> fuse prog -y 0 57 0x78563412 0x0000bc9a - - 2- Read OTP - STM32MP> fuse sense 0 57 2 - Sensing bank 0: - Word 0x00000039: 78563412 0000bc9a - - 3- next REBOOT : - ### Setting environment from OTP MAC address = "12:34:56:78:9a:bc" - - 4 check env update - STM32MP> env print ethaddr - ethaddr=12:34:56:78:9a:bc - -warning:: This MAC address provisioning can't be executed twice on the same - board as the OTP are protected. It is already done for the board - provided by STMicroelectronics. - -10. Coprocessor firmware -======================== - -U-Boot can boot the coprocessor before the kernel (coprocessor early boot). - -A/ Manuallly by using rproc commands (update the bootcmd) - Configurations - # env set name_copro "rproc-m4-fw.elf" - # env set dev_copro 0 - # env set loadaddr_copro 0xC1000000 - - Load binary from bootfs partition (number 4) on SDCard (mmc 0) - # ext4load mmc 0:4 ${loadaddr_copro} ${name_copro} - => ${filesize} updated with the size of the loaded file - - Start M4 firmware with remote proc command - # rproc init - # rproc load ${dev_copro} ${loadaddr_copro} ${filesize} - # rproc start ${dev_copro} - -B/ Automatically by using FIT feature and generic DISTRO bootcmd - - see examples in this directory : - - Generate FIT including kernel + device tree + M4 firmware - with cfg with M4 boot - $> mkimage -f fit_copro_kernel_dtb.its fit_copro_kernel_dtb.itb - - Then using DISTRO configuration file: see extlinux.conf to select - the correct configuration - => stm32mp157c-ev1-m4 - => stm32mp157c-dk2-m4 - -11. DFU support -=============== - -The DFU is supported on ST board. -The env variable dfu_alt_info is automatically build, and all -the memory present on the ST boards are exported. - -The mode is started by - -STM32MP> dfu 0 - -On EV1 board: - -STM32MP> dfu 0 list - -DFU alt settings list: -dev: RAM alt: 0 name: uImage layout: RAM_ADDR -dev: RAM alt: 1 name: devicetree.dtb layout: RAM_ADDR -dev: RAM alt: 2 name: uramdisk.image.gz layout: RAM_ADDR -dev: eMMC alt: 3 name: sdcard_fsbl1 layout: RAW_ADDR -dev: eMMC alt: 4 name: sdcard_fsbl2 layout: RAW_ADDR -dev: eMMC alt: 5 name: sdcard_ssbl layout: RAW_ADDR -dev: eMMC alt: 6 name: sdcard_bootfs layout: RAW_ADDR -dev: eMMC alt: 7 name: sdcard_vendorfs layout: RAW_ADDR -dev: eMMC alt: 8 name: sdcard_rootfs layout: RAW_ADDR -dev: eMMC alt: 9 name: sdcard_userfs layout: RAW_ADDR -dev: eMMC alt: 10 name: emmc_fsbl1 layout: RAW_ADDR -dev: eMMC alt: 11 name: emmc_fsbl2 layout: RAW_ADDR -dev: eMMC alt: 12 name: emmc_ssbl layout: RAW_ADDR -dev: eMMC alt: 13 name: emmc_bootfs layout: RAW_ADDR -dev: eMMC alt: 14 name: emmc_vendorfs layout: RAW_ADDR -dev: eMMC alt: 15 name: emmc_rootfs layout: RAW_ADDR -dev: eMMC alt: 16 name: emmc_userfs layout: RAW_ADDR -dev: MTD alt: 17 name: nor_fsbl1 layout: RAW_ADDR -dev: MTD alt: 18 name: nor_fsbl2 layout: RAW_ADDR -dev: MTD alt: 19 name: nor_ssbl layout: RAW_ADDR -dev: MTD alt: 20 name: nor_env layout: RAW_ADDR -dev: MTD alt: 21 name: nand_fsbl layout: RAW_ADDR -dev: MTD alt: 22 name: nand_ssbl1 layout: RAW_ADDR -dev: MTD alt: 23 name: nand_ssbl2 layout: RAW_ADDR -dev: MTD alt: 24 name: nand_UBI layout: RAW_ADDR -dev: VIRT alt: 25 name: OTP layout: RAW_ADDR -dev: VIRT alt: 26 name: PMIC layout: RAW_ADDR - -All the supported device are exported for dfu-util tool: - -$> dfu-util -l -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=26, name="PMIC", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=25, name="OTP", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=24, name="nand_UBI", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=23, name="nand_ssbl2", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=22, name="nand_ssbl1", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=21, name="nand_fsbl", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=20, name="nor_env", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=19, name="nor_ssbl", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=18, name="nor_fsbl2", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=17, name="nor_fsbl1", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=16, name="emmc_userfs", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=15, name="emmc_rootfs", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=14, name="emmc_vendorfs", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=13, name="emmc_bootfs", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=12, name="emmc_ssbl", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=11, name="emmc_fsbl2", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=10, name="emmc_fsbl1", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=9, name="sdcard_userfs", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=8, name="sdcard_rootfs", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=7, name="sdcard_vendorfs", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=6, name="sdcard_bootfs", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=5, name="sdcard_ssbl", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=4, name="sdcard_fsbl2", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=3, name="sdcard_fsbl1", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=2, name="uramdisk.image.gz", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=1, name="devicetree.dtb", serial="002700333338511934383330" -Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=0, name="uImage", serial="002700333338511934383330" - -You can update the boot device: - -#SDCARD -$> dfu-util -d 0483:5720 -a 3 -D tf-a-stm32mp157c-ev1-trusted.stm32 -$> dfu-util -d 0483:5720 -a 4 -D tf-a-stm32mp157c-ev1-trusted.stm32 -$> dfu-util -d 0483:5720 -a 5 -D u-boot-stm32mp157c-ev1-trusted.img -$> dfu-util -d 0483:5720 -a 6 -D st-image-bootfs-openstlinux-weston-stm32mp1.ext4 -$> dfu-util -d 0483:5720 -a 7 -D st-image-vendorfs-openstlinux-weston-stm32mp1.ext4 -$> dfu-util -d 0483:5720 -a 8 -D st-image-weston-openstlinux-weston-stm32mp1.ext4 -$> dfu-util -d 0483:5720 -a 9 -D st-image-userfs-openstlinux-weston-stm32mp1.ext4 - -#EMMC -$> dfu-util -d 0483:5720 -a 10 -D tf-a-stm32mp157c-ev1-trusted.stm32 -$> dfu-util -d 0483:5720 -a 11 -D tf-a-stm32mp157c-ev1-trusted.stm32 -$> dfu-util -d 0483:5720 -a 12 -D u-boot-stm32mp157c-ev1-trusted.img -$> dfu-util -d 0483:5720 -a 13 -D st-image-bootfs-openstlinux-weston-stm32mp1.ext4 -$> dfu-util -d 0483:5720 -a 14 -D st-image-vendorfs-openstlinux-weston-stm32mp1.ext4 -$> dfu-util -d 0483:5720 -a 15 -D st-image-weston-openstlinux-weston-stm32mp1.ext4 -$> dfu-util -d 0483:5720 -a 16 -D st-image-userfs-openstlinux-weston-stm32mp1.ext4 - -#NOR -$> dfu-util -d 0483:5720 -a 17 -D tf-a-stm32mp157c-ev1-trusted.stm32 -$> dfu-util -d 0483:5720 -a 18 -D tf-a-stm32mp157c-ev1-trusted.stm32 -$> dfu-util -d 0483:5720 -a 19 -D u-boot-stm32mp157c-ev1-trusted.img - -#NAND (UBI partition used for NAND only boot or NOR + NAND boot) -$> dfu-util -d 0483:5720 -a 21 -D tf-a-stm32mp157c-ev1-trusted.stm32 -$> dfu-util -d 0483:5720 -a 22 -D u-boot-stm32mp157c-ev1-trusted.img -$> dfu-util -d 0483:5720 -a 23 -D u-boot-stm32mp157c-ev1-trusted.img -$> dfu-util -d 0483:5720 -a 24 -D st-image-weston-openstlinux-weston-stm32mp1_nand_4_256_multivolume.ubi - -And you can also dump the OTP and the PMIC NVM with: - -$> dfu-util -d 0483:5720 -a 25 -U otp.bin -$> dfu-util -d 0483:5720 -a 26 -U pmic.bin +see doc/board/st/stm32mp1.rst diff --git a/doc/board/index.rst b/doc/board/index.rst index b8b956d730..d43e536ca3 100644 --- a/doc/board/index.rst +++ b/doc/board/index.rst @@ -16,4 +16,5 @@ Board-specific doc renesas/index rockchip/index sifive/index + st/index xilinx/index diff --git a/doc/board/st/index.rst b/doc/board/st/index.rst new file mode 100644 index 0000000000..91f1d51b42 --- /dev/null +++ b/doc/board/st/index.rst @@ -0,0 +1,9 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +STMicroelectronics +================== + +.. toctree:: + :maxdepth: 2 + + stm32mp1 diff --git a/doc/board/st/stm32mp1.rst b/doc/board/st/stm32mp1.rst new file mode 100644 index 0000000000..131f4902a3 --- /dev/null +++ b/doc/board/st/stm32mp1.rst @@ -0,0 +1,598 @@ +.. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause +.. sectionauthor:: Patrick Delaunay <patrick.delaunay(a)st.com> + +STM32MP15x boards +================= + +This is a quick instruction for setup STM32MP15x boards. + +Supported devices +----------------- + +U-Boot supports STMP32MP15x SoCs: + - STM32MP157 + - STM32MP153 + - STM32MP151 + +The STM32MP15x is a Cortex-A MPU aimed at various applications. + +It features: + - Dual core Cortex-A7 application core (Single on STM32MP151) + - 2D/3D image composition with GPU (only on STM32MP157) + - Standard memories interface support + - Standard connectivity, widely inherited from the STM32 MCU family + - Comprehensive security support + +Everything is supported in Linux but U-Boot is limited to: + 1. UART + 2. SD card/MMC controller (SDMMC) + 3. NAND controller (FMC) + 4. NOR controller (QSPI) + 5. USB controller (OTG DWC2) + 6. Ethernet controller + +And the necessary drivers + 1. I2C + 2. STPMIC1 (PMIC and regulator) + 3. Clock, Reset, Sysreset + 4. Fuse + +Currently the following boards are supported: + + stm32mp157a-avenger96.dts + + stm32mp157a-dk1.dts + + stm32mp157c-dk2.dts + + stm32mp157c-ed1.dts + + stm32mp157c-ev1.dts + +Boot Sequences +-------------- + +3 boot configurations are supported with: + ++----------+------------------------+-------------------------+--------------+ +| **ROM** | **FSBL** | **SSBL** | **OS** | ++ **code** +------------------------+-------------------------+--------------+ +| | First Stage Bootloader | Second Stage Bootloader | Linux Kernel | ++ +------------------------+-------------------------+--------------+ +| | embedded RAM | DDR | ++----------+------------------------+-------------------------+--------------+ + +The **Trusted** boot chain +`````````````````````````` + +defconfig_file : stm32mp15_trusted_defconfig + + +-------------+-------------------------+------------+-------+ + | ROM code | FSBL | SSBL | OS | + + +-------------------------+------------+-------+ + | |Trusted Firmware-A (TF-A)| U-Boot | Linux | + +-------------+-------------------------+------------+-------+ + | TrustZone |TF-A secure monitor | + +-------------+-------------------------+------------+-------+ + +TF-A performs a full initialization of Secure peripherals and installs a +secure monitor (BL32=SPMin). + +U-Boot is running in normal world and uses TF-A monitor to access +to secure resources. + +The **Trusted** boot chain with **OP-TEE** +`````````````````````````````````````````` + +defconfig_file : stm32mp15_optee_defconfig + + +-------------+-------------------------+------------+-------+ + | ROM code | FSBL | SSBL | OS | + + +-------------------------+------------+-------+ + | |Trusted Firmware-A (TF-A)| U-Boot | Linux | + +-------------+-------------------------+------------+-------+ + | TrustZone |OP-TEE | + +-------------+-------------------------+------------+-------+ + +TF-A performs a full initialization of Secure peripherals and installs OP-TEE +from specific partitions (teeh, teed, teex). + +U-Boot is running in normal world and uses OP-TEE monitor to access +to secure resources. + +The **Basic** boot chain +```````````````````````` + +defconfig_file : stm32mp15_basic_defconfig + + +-------------+------------+------------+-------+ + | ROM code | FSBL | SSBL | OS | + + +------------+------------+-------+ + | |U-Boot SPL | U-Boot | Linux | + +-------------+------------+------------+-------+ + | TrustZone | | PSCI from U-Boot | + +-------------+------------+------------+-------+ + +SPL has limited security initialization + +U-Boot is running in secure mode and provide a secure monitor to the kernel +with only PSCI support (Power State Coordination Interface defined by ARM). + +All the STM32MP15x boards supported by U-Boot use the same generic board +stm32mp1 which support all the bootable devices. + +Each board is configured only with the associated device tree. + +Device Tree Selection +--------------------- + +You need to select the appropriate device tree for your board, +the supported device trees for STM32MP15x are: + ++ ev1: eval board with pmic stpmic1 (ev1 = mother board + daughter ed1) + + stm32mp157c-ev1 + ++ ed1: daughter board with pmic stpmic1 + + stm32mp157c-ed1 + ++ dk1: Discovery board + + stm32mp157a-dk1 + ++ dk2: Discovery board = dk1 with a BT/WiFI combo and a DSI panel + + stm32mp157c-dk2 + ++ avenger96: Avenger96 board from Arrow Electronics + + stm32mp157a-avenger96 + +Build Procedure +--------------- + +1. Install the required tools for U-Boot + + * install package needed in U-Boot makefile + (libssl-dev, swig, libpython-dev...) + + * install ARMv7 toolchain for 32bit Cortex-A (from Linaro, + from SDK for STM32MP15x, or any crosstoolchains from your distribution) + (you can use any gcc cross compiler compatible with U-Boot) + +2. Set the cross compiler:: + + # export CROSS_COMPILE=/path/to/toolchain/arm-linux-gnueabi- + +3. Select the output directory (optional):: + + # export KBUILD_OUTPUT=/path/to/output + + for example: use one output directory for each configuration:: + + # export KBUILD_OUTPUT=stm32mp15_trusted + # export KBUILD_OUTPUT=stm32mp15_optee + # export KBUILD_OUTPUT=stm32mp15_basic + + you can build outside of code directory:: + + # export KBUILD_OUTPUT=../build/stm32mp15_trusted + +4. Configure U-Boot:: + + # make <defconfig_file> + + with <defconfig_file>: + + - For **trusted** boot mode : **stm32mp15_trusted_defconfig** + - For **trusted** with OP-TEE boot mode : **stm32mp15_optee_defconfig** + - For basic boot mode: stm32mp15_basic_defconfig + +5. Configure the device-tree and build the U-Boot image:: + + # make DEVICE_TREE=<name> all + + Examples: + + a) trusted boot on ev1:: + + # export KBUILD_OUTPUT=stm32mp15_trusted + # make stm32mp15_trusted_defconfig + # make DEVICE_TREE=stm32mp157c-ev1 all + + b) trusted with OP-TEE boot on dk2:: + + # export KBUILD_OUTPUT=stm32mp15_optee + # make stm32mp15_optee_defconfig + # make DEVICE_TREE=stm32mp157c-dk2 all + + c) basic boot on ev1:: + + # export KBUILD_OUTPUT=stm32mp15_basic + # make stm32mp15_basic_defconfig + # make DEVICE_TREE=stm32mp157c-ev1 all + + d) basic boot on ed1:: + + # export KBUILD_OUTPUT=stm32mp15_basic + # make stm32mp15_basic_defconfig + # make DEVICE_TREE=stm32mp157c-ed1 all + + e) basic boot on dk1:: + + # export KBUILD_OUTPUT=stm32mp15_basic + # make stm32mp15_basic_defconfig + # make DEVICE_TREE=stm32mp157a-dk1 all + + f) basic boot on avenger96:: + + # export KBUILD_OUTPUT=stm32mp15_basic + # make stm32mp15_basic_defconfig + # make DEVICE_TREE=stm32mp157a-avenger96 all + +6. Output files + + BootRom and TF-A expect binaries with STM32 image header + SPL expects file with U-Boot uImage header + + So in the output directory (selected by KBUILD_OUTPUT), + you can found the needed files: + + - For **Trusted** boot (with or without OP-TEE) + - FSBL = **tf-a.stm32** (provided by TF-A compilation) + - SSBL = **u-boot.stm32** + + - For Basic boot + - FSBL = spl/u-boot-spl.stm32 + - SSBL = u-boot.img + +Switch Setting for Boot Mode +---------------------------- + +You can select the boot mode, on the board with one switch, to select +the boot pin values = BOOT0, BOOT1, BOOT2 + + +-------------+---------+---------+---------+ + |*Boot Mode* | *BOOT2* | *BOOT1* | *BOOT0* | + +=============+=========+=========+=========+ + | Recovery | 0 | 0 | 0 | + +-------------+---------+---------+---------+ + | NOR | 0 | 0 | 1 | + +-------------+---------+---------+---------+ + | eMMC | 0 | 1 | 0 | + +-------------+---------+---------+---------+ + | NAND | 0 | 1 | 1 | + +-------------+---------+---------+---------+ + | Reserved | 1 | 0 | 0 | + +-------------+---------+---------+---------+ + | SD-Card | 1 | 0 | 1 | + +-------------+---------+---------+---------+ + | Recovery | 1 | 1 | 0 | + +-------------+---------+---------+---------+ + | SPI-NAND | 1 | 1 | 1 | + +-------------+---------+---------+---------+ + +- on the **daugther board ed1 = MB1263** with the switch SW1 +- on **Avenger96** with switch S3 (NOR and SPI-NAND are not applicable) +- on board **DK1/DK2** with the switch SW1 = BOOT0, BOOT2 + with only 2 pins available (BOOT1 is forced to 0 and NOR not supported), + the possible value becomes: + + +-------------+---------+---------+ + |*Boot Mode* | *BOOT2* | *BOOT0* | + +=============+=========+=========+ + | Recovery | 0 | 0 | + +-------------+---------+---------+ + | NOR (NA)| 0 | 1 | + +-------------+---------+---------+ + | Reserved | 1 | 0 | + +-------------+---------+---------+ + | SD-Card | 1 | 1 | + +-------------+---------+---------+ + +Recovery is a boot from serial link (UART/USB) and it is used with +STM32CubeProgrammer tool to load executable in RAM and to update the flash +devices available on the board (NOR/NAND/eMMC/SD card). + +The communication between HOST and board is based on + - for UARTs : the uart protocol used with all MCU STM32 + - for USB : based on USB DFU 1.1 (without the ST extensions used on MCU STM32) + +Prepare an SD card +------------------ + +The minimal requirements for STMP32MP15x boot up to U-Boot are: + +- GPT partitioning (with gdisk or with sgdisk) +- 2 fsbl partitions, named fsbl1 and fsbl2, size at least 256KiB +- one ssbl partition for U-Boot + +Then the minimal GPT partition is: + + +-------+--------+---------+-------------+ + | *Num* | *Name* | *Size* | *Content* | + +=======+========+=========+=============+ + | 1 | fsbl1 | 256 KiB | TF-A or SPL | + +-------+--------+---------+-------------+ + | 2 | fsbl2 | 256 KiB | TF-A or SPL | + +-------+--------+---------+-------------+ + | 3 | ssbl | enought | U-Boot | + +-------+--------+---------+-------------+ + | 4 | <any> | <any> | Rootfs | + +-------+--------+---------+-------------+ + +Add a 4th partition (Rootfs) marked bootable with a file extlinux.conf +following the Generic Distribution feature (doc/README.distro for use). + +According the used card reader select the correct block device +(for example /dev/sdx or /dev/mmcblk0). + +In the next example, it is /dev/mmcblk0 + +For example: with gpt table with 128 entries + +a) remove previous formatting:: + + # sgdisk -o /dev/<SD card dev> + +b) create minimal image:: + + # sgdisk --resize-table=128 -a 1 \ + -n 1:34:545 -c 1:fsbl1 \ + -n 2:546:1057 -c 2:fsbl2 \ + -n 3:1058:5153 -c 3:ssbl \ + -n 4:5154: -c 4:rootfs \ + -p /dev/<SD card dev> + + With other partition for kernel one partition rootfs for kernel. + +c) copy the FSBL (2 times) and SSBL file on the correct partition. + in this example in partition 1 to 3 + + for basic boot mode : <SD card dev> = /dev/mmcblk0:: + + # dd if=u-boot-spl.stm32 of=/dev/mmcblk0p1 + # dd if=u-boot-spl.stm32 of=/dev/mmcblk0p2 + # dd if=u-boot.img of=/dev/mmcblk0p3 + + for trusted boot mode: :: + + # dd if=tf-a.stm32 of=/dev/mmcblk0p1 + # dd if=tf-a.stm32 of=/dev/mmcblk0p2 + # dd if=u-boot.stm32 of=/dev/mmcblk0p3 + +To boot from SD card, select BootPinMode = 1 0 1 and reset. + +Prepare eMMC +------------ + +You can use U-Boot to copy binary in eMMC. + +In the next example, you need to boot from SD card and the images +(u-boot-spl.stm32, u-boot.img) are presents on SD card (mmc 0) +in ext4 partition 4 (bootfs). + +To boot from SD card, select BootPinMode = 1 0 1 and reset. + +Then you update the eMMC with the next U-Boot command : + +a) prepare GPT on eMMC, + example with 2 partitions, bootfs and roots:: + + # setenv emmc_part "name=ssbl,size=2MiB;name=bootfs,type=linux,bootable,size=64MiB;name=rootfs,type=linux,size=512" + # gpt write mmc 1 ${emmc_part} + +b) copy SPL on eMMC on firts boot partition + (SPL max size is 256kB, with LBA 512, 0x200):: + + # ext4load mmc 0:4 0xC0000000 u-boot-spl.stm32 + # mmc dev 1 + # mmc partconf 1 1 1 1 + # mmc write ${fileaddr} 0 200 + # mmc partconf 1 1 1 0 + +c) copy U-Boot in first GPT partition of eMMC:: + + # ext4load mmc 0:4 0xC0000000 u-boo t.img + # mmc dev 1 + # part start mmc 1 1 partstart + # mmc write ${fileaddr} ${partstart} ${filesize} + +To boot from eMMC, select BootPinMode = 0 1 0 and reset. + +MAC Address +----------- + +Please read doc/README.enetaddr for the implementation guidelines for mac id +usage. Basically, environment has precedence over board specific storage. + +For STMicroelectonics board, it is retrieved in STM32MP15x OTP : + - OTP_57[31:0] = MAC_ADDR[31:0] + - OTP_58[15:0] = MAC_ADDR[47:32] + +To program a MAC address on virgin OTP words above, you can use the fuse command +on bank 0 to access to internal OTP: + +Prerequisite: check if a MAC address isn't yet programmed in OTP + +1) check OTP: their value must be equal to 0 + + STM32MP> fuse sense 0 57 2 + Sensing bank 0: + Word 0x00000039: 00000000 00000000 + +2) check environment variable + + STM32MP> env print ethaddr + ## Error: "ethaddr" not defined + +Example to set mac address "12:34:56:78:9a:bc" + +1) Write OTP:: + + STM32MP> fuse prog -y 0 57 0x78563412 0x0000bc9a + +2) Read OTP:: + + STM32MP> fuse sense 0 57 2 + Sensing bank 0: + Word 0x00000039: 78563412 0000bc9a + +3) next REBOOT, in the trace:: + + ### Setting environment from OTP MAC address = "12:34:56:78:9a:bc" + +4) check env update:: + + STM32MP> env print ethaddr + ethaddr=12:34:56:78:9a:bc + +.. warning:: This command can't be executed twice on the same board as + OTP are protected. It is already done for the board + provided by STMicroelectronics. + +Coprocessor firmware +-------------------- + +U-Boot can boot the coprocessor before the kernel (coprocessor early boot). + +a) Manuallly by using rproc commands (update the bootcmd) + + Configurations:: + + # env set name_copro "rproc-m4-fw.elf" + # env set dev_copro 0 + # env set loadaddr_copro 0xC1000000 + + Load binary from bootfs partition (number 4) on SD card (mmc 0):: + + # ext4load mmc 0:4 ${loadaddr_copro} ${name_copro} + + => ${filesize} variable is updated with the size of the loaded file. + + Start M4 firmware with remote proc command:: + + # rproc init + # rproc load ${dev_copro} ${loadaddr_copro} ${filesize} + # rproc start ${dev_copro}"00270033 + +b) Automatically by using FIT feature and generic DISTRO bootcmd + + see examples in the board stm32mp1 directory: fit_copro_kernel_dtb.its + + Generate FIT including kernel + device tree + M4 firmware with cfg with M4 boot:: + + $> mkimage -f fit_copro_kernel_dtb.its fit_copro_kernel_dtb.itb + + Then using DISTRO configuration file: see extlinux.conf to select the correct + configuration: + + - stm32mp157c-ev1-m4 + - stm32mp157c-dk2-m4 + +DFU support +----------- + +The DFU is supported on ST board. + +The env variable dfu_alt_info is automatically build, and all +the memory present on the ST boards are exported. + +The dfu mode is started by the command:: + + STM32MP> dfu 0 + +On EV1 board, booting from SD card, without OP-TEE:: + + STM32MP> dfu 0 list + DFU alt settings list: + dev: RAM alt: 0 name: uImage layout: RAM_ADDR + dev: RAM alt: 1 name: devicetree.dtb layout: RAM_ADDR + dev: RAM alt: 2 name: uramdisk.image.gz layout: RAM_ADDR + dev: eMMC alt: 3 name: sdcard_fsbl1 layout: RAW_ADDR + dev: eMMC alt: 4 name: sdcard_fsbl2 layout: RAW_ADDR + dev: eMMC alt: 5 name: sdcard_ssbl layout: RAW_ADDR + dev: eMMC alt: 6 name: sdcard_bootfs layout: RAW_ADDR + dev: eMMC alt: 7 name: sdcard_vendorfs layout: RAW_ADDR + dev: eMMC alt: 8 name: sdcard_rootfs layout: RAW_ADDR + dev: eMMC alt: 9 name: sdcard_userfs layout: RAW_ADDR + dev: eMMC alt: 10 name: emmc_fsbl1 layout: RAW_ADDR + dev: eMMC alt: 11 name: emmc_fsbl2 layout: RAW_ADDR + dev: eMMC alt: 12 name: emmc_ssbl layout: RAW_ADDR + dev: eMMC alt: 13 name: emmc_bootfs layout: RAW_ADDR + dev: eMMC alt: 14 name: emmc_vendorfs layout: RAW_ADDR + dev: eMMC alt: 15 name: emmc_rootfs layout: RAW_ADDR + dev: eMMC alt: 16 name: emmc_userfs layout: RAW_ADDR + dev: MTD alt: 17 name: nor_fsbl1 layout: RAW_ADDR + dev: MTD alt: 18 name: nor_fsbl2 layout: RAW_ADDR + dev: MTD alt: 19 name: nor_ssbl layout: RAW_ADDR + dev: MTD alt: 20 name: nor_env layout: RAW_ADDR + dev: MTD alt: 21 name: nand_fsbl layout: RAW_ADDR + dev: MTD alt: 22 name: nand_ssbl1 layout: RAW_ADDR + dev: MTD alt: 23 name: nand_ssbl2 layout: RAW_ADDR + dev: MTD alt: 24 name: nand_UBI layout: RAW_ADDR + dev: VIRT alt: 25 name: OTP layout: RAW_ADDR + dev: VIRT alt: 26 name: PMIC layout: RAW_ADDR + +All the supported device are exported for dfu-util tool:: + + $> dfu-util -l + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=26, name="PMIC", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=25, name="OTP", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=24, name="nand_UBI", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=23, name="nand_ssbl2", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=22, name="nand_ssbl1", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=21, name="nand_fsbl", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=20, name="nor_env", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=19, name="nor_ssbl", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=18, name="nor_fsbl2", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=17, name="nor_fsbl1", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=16, name="emmc_userfs", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=15, name="emmc_rootfs", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=14, name="emmc_vendorfs", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=13, name="emmc_bootfs", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=12, name="emmc_ssbl", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=11, name="emmc_fsbl2", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=10, name="emmc_fsbl1", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=9, name="sdcard_userfs", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=8, name="sdcard_rootfs", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=7, name="sdcard_vendorfs", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=6, name="sdcard_bootfs", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=5, name="sdcard_ssbl", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=4, name="sdcard_fsbl2", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=3, name="sdcard_fsbl1", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=2, name="uramdisk.image.gz", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=1, name="devicetree.dtb", serial="002700333338511934383330" + Found DFU: [0483:5720] ver=9999, devnum=99, cfg=1, intf=0, alt=0, name="uImage", serial="002700333338511934383330" + +You can update the boot device: + +- SD card (mmc0) :: + + $> dfu-util -d 0483:5720 -a 3 -D tf-a-stm32mp157c-ev1-trusted.stm32 + $> dfu-util -d 0483:5720 -a 4 -D tf-a-stm32mp157c-ev1-trusted.stm32 + $> dfu-util -d 0483:5720 -a 5 -D u-boot-stm32mp157c-ev1-trusted.img + $> dfu-util -d 0483:5720 -a 6 -D st-image-bootfs-openstlinux-weston-stm32mp1.ext4 + $> dfu-util -d 0483:5720 -a 7 -D st-image-vendorfs-openstlinux-weston-stm32mp1.ext4 + $> dfu-util -d 0483:5720 -a 8 -D st-image-weston-openstlinux-weston-stm32mp1.ext4 + $> dfu-util -d 0483:5720 -a 9 -D st-image-userfs-openstlinux-weston-stm32mp1.ext4 + +- EMMC (mmc1):: + + $> dfu-util -d 0483:5720 -a 10 -D tf-a-stm32mp157c-ev1-trusted.stm32 + $> dfu-util -d 0483:5720 -a 11 -D tf-a-stm32mp157c-ev1-trusted.stm32 + $> dfu-util -d 0483:5720 -a 12 -D u-boot-stm32mp157c-ev1-trusted.img + $> dfu-util -d 0483:5720 -a 13 -D st-image-bootfs-openstlinux-weston-stm32mp1.ext4 + $> dfu-util -d 0483:5720 -a 14 -D st-image-vendorfs-openstlinux-weston-stm32mp1.ext4 + $> dfu-util -d 0483:5720 -a 15 -D st-image-weston-openstlinux-weston-stm32mp1.ext4 + $> dfu-util -d 0483:5720 -a 16 -D st-image-userfs-openstlinux-weston-stm32mp1.ext4 + +- NOR:: + + $> dfu-util -d 0483:5720 -a 17 -D tf-a-stm32mp157c-ev1-trusted.stm32 + $> dfu-util -d 0483:5720 -a 18 -D tf-a-stm32mp157c-ev1-trusted.stm32 + $> dfu-util -d 0483:5720 -a 19 -D u-boot-stm32mp157c-ev1-trusted.img + +- NAND (UBI partition used for NAND only boot or NOR + NAND boot):: + + $> dfu-util -d 0483:5720 -a 21 -D tf-a-stm32mp157c-ev1-trusted.stm32 + $> dfu-util -d 0483:5720 -a 22 -D u-boot-stm32mp157c-ev1-trusted.img + $> dfu-util -d 0483:5720 -a 23 -D u-boot-stm32mp157c-ev1-trusted.img + $> dfu-util -d 0483:5720 -a 24 -D st-image-weston-openstlinux-weston-stm32mp1_nand_4_256_multivolume.ubi + +- you can also dump the OTP and the PMIC NVM with:: + + $> dfu-util -d 0483:5720 -a 25 -U otp.bin + $> dfu-util -d 0483:5720 -a 26 -U pmic.bin + -- 2.17.1

1 0

u-boot saveenv corrupted other MTD parttions
by JH 18 Feb '20

18 Feb '20

Hi, I have three MTD partitions, the mtd2 storage installed UBIFS volumes, first is dtb volume, second is kernel volume, third is rootfs volume. The saveenv was configured to save environment variables to NAND ubootenv. gpmi-nand:1m(boot),1m(ubootenv),-(storage) There was no issue to run NAND boot, but if I called saveenv in u-boot, then I run bootcmd again, it could not boot from NAND any more: Bad Linux ARM zImage magic! The saveenv does not take any parameters, how did it work to write to the NAND 1m(ubootenv)? => saveenv Saving Environment to NAND... Erasing NAND... Erasing at 0x5e0000 -- 100% complete. Writing to NAND... OK It looks like that saveenv overwritten to the storage, is 0x5e0000 RAM or NAND address? Where was that address defined? How do I know it was the NAND 1m(ubootenv) address? Thank you. Kind regards, - jh

2 1

[PATCH v2 00/10] Add Support for eMMC boot in AM65x and J721e
by Faiz Abbas 18 Feb '20

18 Feb '20

The following patches add support for eMMC boot in TI's Am65x and J721e devices. v2: 1. Reordered the patches according to Lokesh's preference 2. Fixed patch 2 breaking platforms where DM_MMC is not enabled. Faiz Abbas (10): mmc: Add a saved_clock member mmc: Add init() API mmc: Merge SD_LEGACY and MMC_LEGACY bus modes mmc: sdhci: Expose sdhci_init() as non-static mmc: am654_sdhci: Update output tap delay writes mmc: am654_sdhci: Implement workaround for card detect spl: mmc: Fix spl_mmc_get_uboot_raw_sector() implementation arm: K3: sysfw-loader: Add a config_pm_pre_callback() configs: am65x_evm: Add CONFIG_SUPPORT_EMMC_BOOT configs: j721e_evm: Add Support for eMMC boot arch/arm/dts/k3-am65-main.dtsi | 12 ++- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 11 +- arch/arm/dts/k3-j721e-main.dtsi | 15 ++- arch/arm/mach-imx/imx8/image.c | 3 +- arch/arm/mach-k3/am6_init.c | 33 +++++- arch/arm/mach-k3/include/mach/sysfw-loader.h | 2 +- arch/arm/mach-k3/j721e_init.c | 33 +++++- arch/arm/mach-k3/sysfw-loader.c | 6 +- common/spl/spl_mmc.c | 11 +- configs/am65x_evm_a53_defconfig | 1 + configs/am65x_evm_r5_defconfig | 1 + configs/j721e_evm_a72_defconfig | 3 + configs/j721e_evm_r5_defconfig | 3 + drivers/mmc/am654_sdhci.c | 105 ++++++++++++++++--- drivers/mmc/fsl_esdhc_imx.c | 1 - drivers/mmc/mmc.c | 31 +++--- drivers/mmc/omap_hsmmc.c | 1 - drivers/mmc/sdhci.c | 2 +- drivers/mmc/zynq_sdhci.c | 1 - include/configs/am65x_evm.h | 2 - include/mmc.h | 9 +- include/sdhci.h | 1 + 22 files changed, 235 insertions(+), 52 deletions(-) -- 2.19.2

9 56

[PATCH] Revert "dm: fdt: scan for devices under /firmware too"
by Thirupathaiah Annapureddy 18 Feb '20

18 Feb '20

Subnodes under "/firmware" node are scanned twice in dm_scan_fdt_node() and dm_extended_scan_fdt(). This patch removes the scanning in dm_scan_fdt_node() to avoid double scanning. This reverts commit 747558d014577526bf2e8d9fe9ca748fdbf75d8a. Signed-off-by: Thirupathaiah Annapureddy <thiruan(a)linux.microsoft.com> --- drivers/core/root.c | 15 +++++---------- 1 file changed, 5 insertions(+), 10 deletions(-) diff --git a/drivers/core/root.c b/drivers/core/root.c index e85643819e..cb695e933a 100644 --- a/drivers/core/root.c +++ b/drivers/core/root.c @@ -254,15 +254,9 @@ static int dm_scan_fdt_node(struct udevice *parent, const void *blob, for (offset = fdt_first_subnode(blob, offset); offset > 0; offset = fdt_next_subnode(blob, offset)) { - const char *node_name = fdt_get_name(blob, offset, NULL); - - /* - * The "chosen" and "firmware" nodes aren't devices - * themselves but may contain some: - */ - if (!strcmp(node_name, "chosen") || - !strcmp(node_name, "firmware")) { - pr_debug("parsing subnodes of \"%s\"\n", node_name); + /* "chosen" node isn't a device itself but may contain some: */ + if (!strcmp(fdt_get_name(blob, offset, NULL), "chosen")) { + pr_debug("parsing subnodes of \"chosen\"\n"); err = dm_scan_fdt_node(parent, blob, offset, pre_reloc_only); @@ -279,7 +273,8 @@ static int dm_scan_fdt_node(struct udevice *parent, const void *blob, pre_reloc_only); if (err && !ret) { ret = err; - debug("%s: ret=%d\n", node_name, ret); + debug("%s: ret=%d\n", fdt_get_name(blob, offset, NULL), + ret); } } -- 2.24.1

2 1

Re: [PATCH v4 06/17] spi: dw: Add device tree properties for fields in CTRL1
by Rick Chen 18 Feb '20

18 Feb '20

Hi Sean > From: U-Boot [mailto:u-boot-bounces@lists.denx.de] On Behalf Of Sean Anderson > Sent: Tuesday, February 11, 2020 2:04 PM > To: u-boot(a)lists.denx.de > Cc: Rick Chen; Eugeniy Paltsev > Subject: [PATCH v4 06/17] spi: dw: Add device tree properties for fields in CTRL1 > > Some devices have different layouts for the fields in CTRL1 (e.g. the Kendryte K210). Allow this layout to be configurable from the device tree. The description of CTRL1 here don't match with the below content of CTRL0. Is it a typo ? Thanks Rick > The documentation has been taken from Linux. > > Signed-off-by: Sean Anderson <seanga2(a)gmail.com> > --- > > Changes in v4: > - New > > .../spi/snps,dw-apb-ssi.txt | 43 +++++++++++++++++++ > drivers/spi/designware_spi.c | 40 ++++++++++------- > 2 files changed, 68 insertions(+), 15 deletions(-) create mode 100644 doc/device-tree-bindings/spi/snps,dw-apb-ssi.txt > > diff --git a/doc/device-tree-bindings/spi/snps,dw-apb-ssi.txt b/doc/device-tree-bindings/spi/snps,dw-apb-ssi.txt > new file mode 100644 > index 0000000000..4b6152f6b7 > --- /dev/null > +++ b/doc/device-tree-bindings/spi/snps,dw-apb-ssi.txt > @@ -0,0 +1,43 @@ > +Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface. > + > +Required properties: > +- compatible : "snps,dw-apb-ssi" > +- reg : The register base for the controller. For "mscc,<soc>-spi", a > +second > + register set is required (named ICPU_CFG:SPI_MST) > +- #address-cells : <1>, as required by generic SPI binding. > +- #size-cells : <0>, also as required by generic SPI binding. > +- clocks : phandles for the clocks, see the description of clock-names below. > + The phandle for the "ssi_clk" is required. The phandle for the "pclk" clock > + is optional. If a single clock is specified but no clock-name, it is the > + "ssi_clk" clock. If both clocks are listed, the "ssi_clk" must be first. > + > +Optional properties: > +- clock-names : Contains the names of the clocks: > + "ssi_clk", for the core clock used to generate the external SPI clock. > + "pclk", the interface clock, required for register access. > +- cs-gpios : Specifies the gpio pins to be used for chipselects. > +- num-cs : The number of chipselects. If omitted, this will default to 4. > +- reg-io-width : The I/O register width (in bytes) implemented by this > + device. Supported values are 2 or 4 (the default). > +- snps,dfs-offset The offset in bits of the DFS field in CTRL0, > +defaulting to 0 > +- snps,frf-offset The offset in bits of the FRF field in CTRL0, > +defaulting to 4 > +- snps,tmod-offset The offset in bits of the tmode field in CTRL0, > +defaulting > + to 6 > +- snps,mode-offset The offset in bits of the work mode field in CTRL0, > + defaulting to 8 > + > +Child nodes as per the generic SPI binding. > + > +Example: > + > + spi@fff00000 { > + compatible = "snps,dw-apb-ssi"; > + reg = <0xfff00000 0x1000>; > + interrupts = <0 154 4>; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&spi_m_clk>; > + num-cs = <2>; > + cs-gpios = <&gpio0 13 0>, > + <&gpio0 14 0>; > + }; > diff --git a/drivers/spi/designware_spi.c b/drivers/spi/designware_spi.c index 66ff8eeccd..04cc873754 100644 > --- a/drivers/spi/designware_spi.c > +++ b/drivers/spi/designware_spi.c > @@ -3,6 +3,7 @@ > * Designware master SPI core controller driver > * > * Copyright (C) 2014 Stefan Roese <sr(a)denx.de> > + * Copyright (C) 2020 Sean Anderson <seanga2(a)gmail.com> > * > * Very loosely based on the Linux driver: > * drivers/spi/spi-dw.c, which is: > @@ -50,20 +51,14 @@ > #define DW_SPI_DR 0x60 > > /* Bit fields in CTRLR0 */ > -#define SPI_DFS_OFFSET 0 > - > -#define SPI_FRF_OFFSET 4 > #define SPI_FRF_SPI 0x0 > #define SPI_FRF_SSP 0x1 > #define SPI_FRF_MICROWIRE 0x2 > #define SPI_FRF_RESV 0x3 > > -#define SPI_MODE_OFFSET 6 > -#define SPI_SCPH_OFFSET 6 > -#define SPI_SCOL_OFFSET 7 > +#define SPI_MODE_SCPH 0x1 > +#define SPI_MODE_SCOL 0x2 > > -#define SPI_TMOD_OFFSET 8 > -#define SPI_TMOD_MASK (0x3 << SPI_TMOD_OFFSET) > #define SPI_TMOD_TR 0x0 /* xmit & recv */ > #define SPI_TMOD_TO 0x1 /* xmit only */ > #define SPI_TMOD_RO 0x2 /* recv only */ > @@ -88,6 +83,12 @@ > struct dw_spi_platdata { > s32 frequency; /* Default clock frequency, -1 for none */ > void __iomem *regs; > + > + /* Offsets in CTRL0 */ > + u8 dfs_off; > + u8 frf_off; > + u8 tmod_off; > + u8 mode_off; > }; > > struct dw_spi_priv { > @@ -114,6 +115,15 @@ struct dw_spi_priv { > struct reset_ctl_bulk resets; > }; > > +static inline u32 GEN_CTRL0(struct dw_spi_priv *priv, > + struct dw_spi_platdata *plat) > +{ > + return ((priv->bits_per_word - 1) << plat->dfs_off | > + (priv->type << plat->frf_off) | > + (priv->mode << plat->mode_off) | > + (priv->tmode << plat->tmod_off)); } > + > static inline u32 dw_read(struct dw_spi_priv *priv, u32 offset) { > return __raw_readl(priv->regs + offset); @@ -159,6 +169,10 @@ static int dw_spi_ofdata_to_platdata(struct udevice *bus) > /* Use 500KHz as a suitable default */ > plat->frequency = dev_read_u32_default(bus, "spi-max-frequency", > 500000); > + plat->dfs_off = dev_read_u32_default(bus, "snps,dfs-offset", 0); > + plat->frf_off = dev_read_u32_default(bus, "snps,frf-offset", 4); > + plat->mode_off = dev_read_u32_default(bus, "snps,mode-offset", 6); > + plat->tmod_off = dev_read_u32_default(bus, "snps,tmod-offset", 8); > debug("%s: regs=%p max-frequency=%d\n", __func__, plat->regs, > plat->frequency); > > @@ -387,6 +401,7 @@ static int dw_spi_xfer(struct udevice *dev, unsigned int bitlen, > const void *dout, void *din, unsigned long flags) { > struct udevice *bus = dev->parent; > + struct dw_spi_platdata *plat = dev_get_platdata(bus); > struct dw_spi_priv *priv = dev_get_priv(bus); > const u8 *tx = dout; > u8 *rx = din; > @@ -405,10 +420,6 @@ static int dw_spi_xfer(struct udevice *dev, unsigned int bitlen, > if (flags & SPI_XFER_BEGIN) > external_cs_manage(dev, false); > > - cr0 = (priv->bits_per_word - 1) | (priv->type << SPI_FRF_OFFSET) | > - (priv->mode << SPI_MODE_OFFSET) | > - (priv->tmode << SPI_TMOD_OFFSET); > - > if (rx && tx) > priv->tmode = SPI_TMOD_TR; > else if (rx) > @@ -420,8 +431,7 @@ static int dw_spi_xfer(struct udevice *dev, unsigned int bitlen, > */ > priv->tmode = SPI_TMOD_TR; > > - cr0 &= ~SPI_TMOD_MASK; > - cr0 |= (priv->tmode << SPI_TMOD_OFFSET); > + cr0 = GEN_CTRL0(priv, plat); > > priv->len = bitlen >> 3; > debug("%s: rx=%p tx=%p len=%d [bytes]\n", __func__, rx, tx, priv->len); @@ -475,7 +485,7 @@ static int dw_spi_xfer(struct udevice *dev, unsigned int bitlen, > > static int dw_spi_set_speed(struct udevice *bus, uint speed) { > - struct dw_spi_platdata *plat = bus->platdata; > + struct dw_spi_platdata *plat = dev_get_platdata(bus); > struct dw_spi_priv *priv = dev_get_priv(bus); > u16 clk_div; > > -- > 2.25.0 >

2 1

[PATCH] am335x: evm: defconfig: disable spl tiny printf
by moseschristopherb＠gmail.com 18 Feb '20

18 Feb '20

From: Moses Christopher Bollavarapu <moseschristopherb(a)gmail.com> - As tiny printf lib is further optimized, the ability to deal with ethaddr is lost. Hence, in order to handle usb-eth boot from SPL we need to disable tiny printf. - Tested on Beagle Bone Black Signed-off-by: Moses Christopher Bollavarapu <moseschristopherb(a)gmail.com> --- configs/am335x_evm_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/configs/am335x_evm_defconfig b/configs/am335x_evm_defconfig index 335aa8cfa1..e3fbe2e5bc 100644 --- a/configs/am335x_evm_defconfig +++ b/configs/am335x_evm_defconfig @@ -77,6 +77,7 @@ CONFIG_USB_ETHER=y CONFIG_WDT=y # CONFIG_SPL_WDT is not set CONFIG_DYNAMIC_CRC_TABLE=y +# CONFIG_SPL_USE_TINY_PRINTF is not set CONFIG_RSA=y CONFIG_LZO=y # CONFIG_OF_LIBFDT_OVERLAY is not set -- 2.20.1

3 2

[PATCH v5] Add support for SoM "VoCore2".
by Mauro Condarelli 18 Feb '20

18 Feb '20

Small patch series to add support for VoCore/VoCore2 board. VoCore is open hardware and runs OpenWrt/LEDE. It has WIFI, USB, UART, 20+ GPIOs but is only one inch square. It will help you to make a smart house, study embedded system or even make the tiniest router in the world. Details about this SoM can be found at "https://vocore.io/v2.html". Signed-off-by: Mauro Condarelli <mc5686(a)mclink.it> --- Changes in v5: - Removed unneeded (and wrong) UART2 initialization in board.c - Added network setup. - Removed project-specific code. - Move back environment to SPI NOR. - Changes to environment default settings. - Rebase on current u-boot-mips/testing Changes in v4: - Reverted some overzealous DTS cleaning. - Added support for bootcount Changes in v3: - based on top of Weijie Gao patchset: "[v3,xx/20]Refactor the architecture parts of mt7628" Changes in v2: - Removed some dead code - Changed Author to my full name (no nick) - Removed unwanted fixup to .dts generation (not my call). - Fixed commit message - Fixed various variables/filenames to include Vendor name - Changed Vendor name (Vonger -> Vocore) arch/mips/dts/Makefile | 1 + arch/mips/dts/mt7628a.dtsi | 5 ++ arch/mips/dts/vocore_vocore2.dts | 78 ++++++++++++++++++++ arch/mips/mach-mtmips/Kconfig | 8 +++ board/vocore/vocore2/Kconfig | 12 ++++ board/vocore/vocore2/Makefile | 3 + board/vocore/vocore2/board.c | 6 ++ configs/vocore2_defconfig | 103 ++++++++++++++++++++++++++ configs/vocore2_defconfig_ENV_IN_FAT | 104 +++++++++++++++++++++++++++ include/configs/vocore2.h | 61 ++++++++++++++++ 10 files changed, 381 insertions(+) create mode 100644 arch/mips/dts/vocore_vocore2.dts create mode 100644 board/vocore/vocore2/Kconfig create mode 100644 board/vocore/vocore2/Makefile create mode 100644 board/vocore/vocore2/board.c create mode 100644 configs/vocore2_defconfig create mode 100644 configs/vocore2_defconfig_ENV_IN_FAT create mode 100644 include/configs/vocore2.h diff --git a/arch/mips/dts/Makefile b/arch/mips/dts/Makefile index cbd0c8bc8b..f711e9fb59 100644 --- a/arch/mips/dts/Makefile +++ b/arch/mips/dts/Makefile @@ -23,6 +23,7 @@ dtb-$(CONFIG_BOARD_NETGEAR_DGND3700V2) += netgear,dgnd3700v2.dtb dtb-$(CONFIG_BOARD_SAGEM_FAST1704) += sagem,f(a)st1704.dtb dtb-$(CONFIG_BOARD_SFR_NB4_SER) += sfr,nb4-ser.dtb dtb-$(CONFIG_BOARD_TPLINK_WDR4300) += tplink_wdr4300.dtb +dtb-$(CONFIG_BOARD_VOCORE2) += vocore_vocore2.dtb dtb-$(CONFIG_TARGET_JZ4780_CI20) += ci20.dtb dtb-$(CONFIG_SOC_LUTON) += luton_pcb090.dtb luton_pcb091.dtb dtb-$(CONFIG_SOC_OCELOT) += ocelot_pcb120.dtb ocelot_pcb123.dtb diff --git a/arch/mips/dts/mt7628a.dtsi b/arch/mips/dts/mt7628a.dtsi index 6baa63add3..192599c37f 100644 --- a/arch/mips/dts/mt7628a.dtsi +++ b/arch/mips/dts/mt7628a.dtsi @@ -402,6 +402,11 @@ builtin-cd = <1>; r_smpl = <1>; + bus-width = <4>; + max-frequency = <48000000>; + cap-sd-highspeed; + cap-mmc-highspeed; + clocks = <&clk48m>, <&clkctrl CLK_SDXC>; clock-names = "source", "hclk"; diff --git a/arch/mips/dts/vocore_vocore2.dts b/arch/mips/dts/vocore_vocore2.dts new file mode 100644 index 0000000000..1d611abb73 --- /dev/null +++ b/arch/mips/dts/vocore_vocore2.dts @@ -0,0 +1,78 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2019 Mauro Condarelli <mc5686(a)mclink.it> + */ + +/dts-v1/; + +#include "mt7628a.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + compatible = "vocore,vocore2", "ralink,mt7628a-soc"; + model = "VoCore2"; + + aliases { + serial0 = &uart2; + spi0 = &spi0; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x08000000>; + }; + leds { + compatible = "gpio-leds"; + + power { + label = "vocore:power"; + gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + chosen { + bootargs = "console=ttyS2,115200"; + stdout-path = &uart2; + }; +}; + +&pinctrl { + state_default: pin_state { + p0led { + groups = "p0led_a"; + function = "led"; + }; + }; +}; + +&uart2 { + status = "okay"; +}; + +&spi0 { + status = "okay"; + nor0: spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <25000000>; + reg = <0>; + }; +}; + +&eth { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&ephy_iot_mode>; + mediatek,poll-link-phy = <0>; +}; + +&mmc { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&sd_iot_mode>; + pinctrl-1 = <&sd_iot_mode>; +}; diff --git a/arch/mips/mach-mtmips/Kconfig b/arch/mips/mach-mtmips/Kconfig index bcd635f438..489e466daf 100644 --- a/arch/mips/mach-mtmips/Kconfig +++ b/arch/mips/mach-mtmips/Kconfig @@ -83,6 +83,13 @@ config BOARD_MT7628_RFB SPI-NOR flash, 1 built-in switch with 5 ports, 1 UART, 1 USB host, 1 SDXC, 1 PCIe socket and JTAG pins. +config BOARD_VOCORE2 + bool "VoCore2" + depends on SOC_MT7628 + help + VoCore VoCore2 board has a MT7628 SoC with 128 MiB of RAM + and 16 MiB of flash (SPI). + endchoice config SPL_UART2_SPIS_PINMUX @@ -96,5 +103,6 @@ config SPL_UART2_SPIS_PINMUX source "board/gardena/smart-gateway-mt7688/Kconfig" source "board/mediatek/mt7628/Kconfig" source "board/seeed/linkit-smart-7688/Kconfig" +source "board/vocore/vocore2/Kconfig" endmenu diff --git a/board/vocore/vocore2/Kconfig b/board/vocore/vocore2/Kconfig new file mode 100644 index 0000000000..baeff31b69 --- /dev/null +++ b/board/vocore/vocore2/Kconfig @@ -0,0 +1,12 @@ +if BOARD_VOCORE2 + +config SYS_BOARD + default "vocore2" + +config SYS_VENDOR + default "vocore" + +config SYS_CONFIG_NAME + default "vocore2" + +endif diff --git a/board/vocore/vocore2/Makefile b/board/vocore/vocore2/Makefile new file mode 100644 index 0000000000..70cd7a8e56 --- /dev/null +++ b/board/vocore/vocore2/Makefile @@ -0,0 +1,3 @@ +# SPDX-License-Identifier: GPL-2.0+ + +obj-y += board.o diff --git a/board/vocore/vocore2/board.c b/board/vocore/vocore2/board.c new file mode 100644 index 0000000000..27e42d1414 --- /dev/null +++ b/board/vocore/vocore2/board.c @@ -0,0 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2019 Mauro Condarelli <mc5686(a)mclink.it> + * + * Nothing actually needed here + */ diff --git a/configs/vocore2_defconfig b/configs/vocore2_defconfig new file mode 100644 index 0000000000..3989aa72f0 --- /dev/null +++ b/configs/vocore2_defconfig @@ -0,0 +1,103 @@ +CONFIG_MIPS=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_ENV_SIZE=0x1000 +CONFIG_ENV_SECT_SIZE=0x1000 +CONFIG_ENV_OFFSET=0x04e000 +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SYS_BOOTCOUNT_ADDR=0xb000006c +CONFIG_SPL_SYS_MALLOC_F_LEN=0x20000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_SPL=y +CONFIG_SYS_BOOTCOUNT_SINGLEWORD=y +CONFIG_ARCH_MTMIPS=y +CONFIG_BOARD_VOCORE2=y +CONFIG_SPL_UART2_SPIS_PINMUX=y +CONFIG_RESTORE_EXCEPTION_VECTOR_BASE=y +CONFIG_MIPS_BOOT_FDT=y +CONFIG_ENV_VARS_UBOOT_CONFIG=y +CONFIG_SYS_BOOT_GET_CMDLINE=y +CONFIG_SYS_BOOT_GET_KBD=y +CONFIG_FIT=y +CONFIG_FIT_SIGNATURE=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_LOGLEVEL=8 +CONFIG_VERSION_VARIABLE=y +# CONFIG_DISPLAY_BOARDINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_NOR_SUPPORT=y +CONFIG_HUSH_PARSER=y +CONFIG_CMD_LICENSE=y +# CONFIG_BOOTM_NETBSD is not set +# CONFIG_BOOTM_PLAN9 is not set +# CONFIG_BOOTM_RTEMS is not set +# CONFIG_BOOTM_VXWORKS is not set +# CONFIG_CMD_ELF is not set +# CONFIG_CMD_XIMG is not set +# CONFIG_CMD_CRC32 is not set +CONFIG_CMD_MEMINFO=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_GPT_RENAME=y +# CONFIG_CMD_LOADS is not set +CONFIG_CMD_MMC=y +CONFIG_CMD_MTD=y +CONFIG_CMD_PART=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +CONFIG_CMD_WDT=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_BOOTCOUNT=y +CONFIG_CMD_TIME=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nor0=spi0.0" +CONFIG_MTDPARTS_DEFAULT="spi0.0:312k(u-boot),4k(env),4k(factory),2368k(kernel),-(filesystem)" +CONFIG_DEFAULT_DEVICE_TREE="vocore_vocore2" +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_SPL_DM=y +# CONFIG_DM_DEVICE_REMOVE is not set +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_LED=y +CONFIG_LED_BLINK=y +CONFIG_LED_GPIO=y +CONFIG_MMC=y +CONFIG_DM_MMC=y +# CONFIG_MMC_HW_PARTITIONING is not set +CONFIG_MMC_MTK=y +CONFIG_MTD=y +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_GIGADEVICE=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_MT7628_ETH=y +CONFIG_PHY=y +CONFIG_MT76X8_USB_PHY=y +# CONFIG_RAM_ROCKCHIP_DEBUG is not set +CONFIG_SPECIFY_CONSOLE_INDEX=y +CONFIG_CONS_INDEX=3 +CONFIG_SPI=y +CONFIG_MT7621_SPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_STORAGE=y +CONFIG_WDT=y +CONFIG_WDT_MT7621=y +CONFIG_FS_EXT4=y +CONFIG_FAT_WRITE=y +CONFIG_LZMA=y +CONFIG_LZO=y diff --git a/configs/vocore2_defconfig_ENV_IN_FAT b/configs/vocore2_defconfig_ENV_IN_FAT new file mode 100644 index 0000000000..02727859e4 --- /dev/null +++ b/configs/vocore2_defconfig_ENV_IN_FAT @@ -0,0 +1,104 @@ +CONFIG_MIPS=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_ENV_SIZE=0x1000 +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL_SYS_MALLOC_F_LEN=0x20000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_SPL=y +CONFIG_SYS_BOOTCOUNT_SINGLEWORD=y +CONFIG_SYS_BOOTCOUNT_ADDR=0xb000006c +CONFIG_ARCH_MTMIPS=y +CONFIG_BOARD_VOCORE2=y +CONFIG_SPL_UART2_SPIS_PINMUX=y +CONFIG_RESTORE_EXCEPTION_VECTOR_BASE=y +CONFIG_MIPS_BOOT_FDT=y +CONFIG_ENV_VARS_UBOOT_CONFIG=y +CONFIG_SYS_BOOT_GET_CMDLINE=y +CONFIG_SYS_BOOT_GET_KBD=y +CONFIG_FIT=y +CONFIG_FIT_SIGNATURE=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_USE_BOOTARGS=y +CONFIG_LOGLEVEL=8 +CONFIG_SYS_CONSOLE_INFO_QUIET=y +CONFIG_VERSION_VARIABLE=y +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_SPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_NOR_SUPPORT=y +CONFIG_HUSH_PARSER=y +CONFIG_CMD_LICENSE=y +# CONFIG_BOOTM_NETBSD is not set +# CONFIG_BOOTM_PLAN9 is not set +# CONFIG_BOOTM_RTEMS is not set +# CONFIG_BOOTM_VXWORKS is not set +# CONFIG_CMD_ELF is not set +# CONFIG_CMD_XIMG is not set +# CONFIG_CMD_CRC32 is not set +CONFIG_CMD_MEMINFO=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_GPT_RENAME=y +# CONFIG_CMD_LOADS is not set +CONFIG_CMD_MMC=y +CONFIG_CMD_MTD=y +CONFIG_CMD_PART=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +CONFIG_CMD_WDT=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_BOOTCOUNT=y +CONFIG_CMD_TIME=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nor0=spi0.0" +CONFIG_MTDPARTS_DEFAULT="spi0.0:312k(u-boot),4k(env),4k(factory),2368k(kernel),-(filesystem)" +CONFIG_DEFAULT_DEVICE_TREE="vocore_vocore2" +CONFIG_ENV_IS_IN_FAT=y +CONFIG_ENV_FAT_INTERFACE="mmc" +CONFIG_ENV_FAT_DEVICE_AND_PART="0:1" +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_SPL_DM=y +# CONFIG_DM_DEVICE_REMOVE is not set +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_LED=y +CONFIG_LED_BLINK=y +CONFIG_LED_GPIO=y +CONFIG_MMC=y +CONFIG_DM_MMC=y +# CONFIG_MMC_HW_PARTITIONING is not set +CONFIG_MMC_MTK=y +CONFIG_MTD=y +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_GIGADEVICE=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_MT7628_ETH=y +CONFIG_PHY=y +CONFIG_MT76X8_USB_PHY=y +# CONFIG_RAM_ROCKCHIP_DEBUG is not set +CONFIG_SPECIFY_CONSOLE_INDEX=y +CONFIG_CONS_INDEX=3 +CONFIG_SPI=y +CONFIG_MT7621_SPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_STORAGE=y +CONFIG_WDT=y +CONFIG_WDT_MT7621=y +CONFIG_FS_EXT4=y +CONFIG_LZMA=y +CONFIG_LZO=y diff --git a/include/configs/vocore2.h b/include/configs/vocore2.h new file mode 100644 index 0000000000..6b43aa766e --- /dev/null +++ b/include/configs/vocore2.h @@ -0,0 +1,61 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2019 Mauro Condarelli <mc5686(a)mclink.it> + */ + +#ifndef __VOCORE2_CONFIG_H__ +#define __VOCORE2_CONFIG_H__ + +/* CPU */ +#define CONFIG_SYS_MIPS_TIMER_FREQ 290000000 + +/* RAM */ +#define CONFIG_SYS_SDRAM_BASE 0x80000000 + +#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE + 0x100000 + +#define CONFIG_SYS_INIT_SP_OFFSET 0x400000 + +/* SPL */ +#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD) +#define CONFIG_SKIP_LOWLEVEL_INIT +#endif + +#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SPL_BSS_START_ADDR 0x80010000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x10000 +#define CONFIG_SPL_MAX_SIZE 0x10000 + +/* Dummy value */ +#define CONFIG_SYS_UBOOT_BASE 0 + +/* Serial SPL */ +#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_SERIAL_SUPPORT) +#define CONFIG_SYS_NS16550_MEM32 +#define CONFIG_SYS_NS16550_CLK 40000000 +#define CONFIG_SYS_NS16550_REG_SIZE -4 +#define CONFIG_SYS_NS16550_COM3 0xb0000e00 +#define CONFIG_CONS_INDEX 3 + +#endif + +/* UART */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, \ + 230400, 460800, 921600 } + +/* RAM */ +#define CONFIG_SYS_MEMTEST_START 0x80100000 +#define CONFIG_SYS_MEMTEST_END 0x80400000 + +/* Memory usage */ +#define CONFIG_SYS_MAXARGS 64 +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) +#define CONFIG_SYS_BOOTPARAMS_LEN (128 * 1024) +#define CONFIG_SYS_CBSIZE 512 + +/* U-Boot */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +/* Environment settings */ + +#endif //__VOCORE2_CONFIG_H__ -- 2.25.0

4 13

[RFC] fixdep: faster CONFIG_search
by Tom Rini 18 Feb '20

18 Feb '20

This is a port of dee81e988674 from Linux ("fixdep: faster CONFIG_ search") and posted by itself for ease of review. To quote the kernel changelog: "Do you think kernel build is 100% dominated by gcc? You are wrong! One small utility called "fixdep" consistently manages to sneak into profile's first page (unless you have small monitor of course). The choke point is this clever code: for (; m < end; m++) { if (*m == INT_CONF) { p = (char *) m ; goto conf; } if (*m == INT_ONFI) { p = (char *) m-1; goto conf; } if (*m == INT_NFIG) { p = (char *) m-2; goto conf; } if (*m == INT_FIG_) { p = (char *) m-3; goto conf; } 4 branches per 4 characters is not fast. Use strstr(3), so that SSE2 etc can be used. With this patch, fixdep is so deep at the bottom, it is hard to find it." Cc: Masahiro Yamada <masahiroy(a)kernel.org> Signed-off-by: Tom Rini <trini(a)konsulko.com> --- As part of working to re-sync our kbuild logic I see that fixdep.c wasn't updated as part of the general resync with v4.17. As this specific change required some thinking to adapt our logic that was added in 8be60f06c258 I am posting this change stand-alone for review. --- scripts/basic/fixdep.c | 100 ++++++++++++++--------------------------- 1 file changed, 33 insertions(+), 67 deletions(-) diff --git a/scripts/basic/fixdep.c b/scripts/basic/fixdep.c index da7fb2cd4dde..6ab1780e4c02 100644 --- a/scripts/basic/fixdep.c +++ b/scripts/basic/fixdep.c @@ -82,8 +82,7 @@ * to date before even starting the recursive build, so it's too late * at this point anyway. * - * The algorithm to grep for "CONFIG_..." is bit unusual, but should - * be fast ;-) We don't even try to really parse the header files, but + * We don't even try to really parse the header files, but * merely grep, i.e. if CONFIG_FOO is mentioned in a comment, it will * be picked up as well. It's not a problem with respect to * correctness, since that can only give too many dependencies, thus @@ -115,11 +114,6 @@ #include <ctype.h> #include <arpa/inet.h> -#define INT_CONF ntohl(0x434f4e46) -#define INT_ONFI ntohl(0x4f4e4649) -#define INT_NFIG ntohl(0x4e464947) -#define INT_FIG_ ntohl(0x4649475f) - char *target; char *depfile; char *cmdline; @@ -217,38 +211,20 @@ static void use_config(const char *m, int slen) printf(".h) \\\n"); } -static void parse_config_file(const char *map, size_t len) +static void parse_config_file(const char *p) { - const int *end = (const int *) (map + len); - /* start at +1, so that p can never be < map */ - const int *m = (const int *) map + 1; - const char *p, *q; + const char *q, *r; char tmp_buf[256] = "SPL_"; /* hack for U-Boot */ - for (; m < end; m++) { - if (*m == INT_CONF) { p = (char *) m ; goto conf; } - if (*m == INT_ONFI) { p = (char *) m-1; goto conf; } - if (*m == INT_NFIG) { p = (char *) m-2; goto conf; } - if (*m == INT_FIG_) { p = (char *) m-3; goto conf; } - continue; - conf: - if (p > map + len - 7) - continue; - if (memcmp(p, "CONFIG_", 7)) - continue; + while ((p = strstr(p, "CONFIG_"))) { p += 7; - for (q = p; q < map + len; q++) { - if (!(isalnum(*q) || *q == '_')) - goto found; - } - continue; - - found: - if (!memcmp(q - 7, "_MODULE", 7)) - q -= 7; - if (q - p < 0) - continue; - + q = p; + while (*q && (isalnum(*q) || *q == '_')) + q++; + if (memcmp(q - 7, "_MODULE", 7) == 0) + r = q - 7; + else + r = q; /* * U-Boot also handles * CONFIG_IS_ENABLED(...) @@ -261,21 +237,20 @@ static void parse_config_file(const char *map, size_t len) (q - p == 9 && !memcmp(p, "IS_MODULE(", 10)) || (q - p == 3 && !memcmp(p, "VAL(", 4))) { p = q + 1; - for (q = p; q < map + len; q++) - if (*q == ')') - goto found2; - continue; - - found2: - if (is_spl_build) { - memcpy(tmp_buf + 4, p, q - p); - q = tmp_buf + 4 + (q - p); + while (*q && *q != ')') + q++; + r = q; + if (r > p && is_spl_build) { + memcpy(tmp_buf + 4, p, r - p); + r = tmp_buf + 4 + (r - p); p = tmp_buf; } } /* end U-Boot hack */ - use_config(p, q - p); + if (r > p) + use_config(p, r - p); + p = q; } } @@ -295,7 +270,7 @@ static void do_config_file(const char *filename) { struct stat st; int fd; - void *map; + char *map; fd = open(filename, O_RDONLY); if (fd < 0) { @@ -312,18 +287,23 @@ static void do_config_file(const char *filename) close(fd); return; } - map = mmap(NULL, st.st_size, PROT_READ, MAP_PRIVATE, fd, 0); - if ((long) map == -1) { - perror("fixdep: mmap"); + map = malloc(st.st_size + 1); + if (!map) { + perror("fixdep: malloc"); close(fd); return; } + if (read(fd, map, st.st_size) != st.st_size) { + perror("fixdep: read"); + close(fd); + return; + } + map[st.st_size] = '\0'; + close(fd); - parse_config_file(map, st.st_size); - - munmap(map, st.st_size); + parse_config_file(map); - close(fd); + free(map); } /* @@ -447,22 +427,8 @@ static void print_deps(void) close(fd); } -static void traps(void) -{ - static char test[] __attribute__((aligned(sizeof(int)))) = "CONF"; - int *p = (int *)test; - - if (*p != INT_CONF) { - fprintf(stderr, "fixdep: sizeof(int) != 4 or wrong endianness? %#x\n", - *p); - exit(2); - } -} - int main(int argc, char *argv[]) { - traps(); - if (argc != 4) usage(); -- 2.17.1

1 0