September 2019 - U-Boot

Re: [U-Boot] Regressions in MTD / SPI FLASH
by Eugeniy Paltsev 25 Sep '19

25 Sep '19

Hi Vignesh, sorry for delay, I was pretty busy with another project :( I've tried to test SPI with CONFIG_SPI_FLASH_SFDP_SUPPORT enabled, however it doesn't seem to work. CONFIG_SPI_FLASH_SFDP_SUPPORT enabled: ---------------------------------->8-------------------------------------------- AXS# sf probe && echo OK 9f | [6B in] 20 ba 20 10 00 00 [ret 0] 5a 00 00 00 | [16B in] 53 46 44 50 00 01 00 ff 00 00 01 09 30 00 00 ff [ret 0] 5a 00 00 30 | [36B in] e5 20 fb ff ff ff ff 1f 29 eb 27 6b 27 3b 27 bb ff ff ff ff ff ff 27 bb ff ff 29 eb 0c 20 10 d8 00 00 00 00 [ret 0] 06 | [0B -] [ret 0] b7 | [0B -] [ret 0] 04 | [0B -] [ret 0] SF: Detected n25q512ax3 with page size 256 Bytes, erase size 64 KiB, total 64 MiB OK AXS# sf read 0x81000000 0x180000 0x10 && echo OK device 0 offset 0x180000, size 0x10 0b 00 18 00 00 | [16B in] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ret 0] SF: 16 bytes @ 0x180000 Read: OK OK AXS# md.b 0x81000000 0x10 81000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ AXS# sf protect unlock 0x0 0x4000000 && echo OK 05 | [1B in] 00 [ret 0] OK AXS# sf erase 0x180000 0x1000 && echo OK SF: Erase offset/length not multiple of erase size SF: 4096 bytes @ 0x180000 Erased: ERROR ---------------------------------->8-------------------------------------------- CONFIG_SPI_FLASH_SFDP_SUPPORT disabled (everything OK): ---------------------------------->8-------------------------------------------- AXS# sf probe && echo OK 9f | [6B in] 20 ba 20 10 00 00 [ret 0] 06 | [0B -] [ret 0] b7 | [0B -] [ret 0] 04 | [0B -] [ret 0] SF: Detected n25q512ax3 with page size 256 Bytes, erase size 4 KiB, total 64 MiB OK AXS# sf read 0x81000000 0x180000 0x10 && echo OK device 0 offset 0x180000, size 0x10 0b 00 18 00 00 | [16B in] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ret 0] SF: 16 bytes @ 0x180000 Read: OK OK AXS# md.b 0x81000000 0x10 81000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ AXS# sf protect unlock 0x0 0x4000000 && echo OK 05 | [1B in] 00 [ret 0] OK AXS# sf erase 0x180000 0x1000 && echo OK 06 | [0B -] [ret 0] 20 00 18 00 00 | [0B -] [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 03 [ret 0] 70 | [1B in] 01 [ret 0] 05 | [1B in] 00 [ret 0] 70 | [1B in] 81 [ret 0] 04 | [0B -] [ret 0] SF: 4096 bytes @ 0x180000 Erased: OK OK AXS# sf read 0x81000000 0x180000 0x10 && echo OK device 0 offset 0x180000, size 0x10 0b 00 18 00 00 | [16B in] ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ret 0] SF: 16 bytes @ 0x180000 Read: OK OK AXS# md.b 0x81000000 0x10 81000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ AXS# mw 0x81000000 0 5 AXS# sf write 0x81000000 0x180000 0x10 && echo OK device 0 offset 0x180000, size 0x10 06 | [0B -] [ret 0] 02 00 18 00 00 | [16B out] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ret 0] 05 | [1B in] 00 [ret 0] 70 | [1B in] 81 [ret 0] SF: 16 bytes @ 0x180000 Written: OK OK AXS# sf read 0x81000000 0x180000 0x10 && echo OK device 0 offset 0x180000, size 0x10 0b 00 18 00 00 | [16B in] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ret 0] SF: 16 bytes @ 0x180000 Read: OK OK AXS# md.b 0x81000000 0x10 81000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ AXS# ---------------------------------->8-------------------------------------------- All tests were performed on 4b95daf5dca with your commit (for disabling 4B opcodes) applied. --- Eugeniy Paltsev ________________________________________ From: Vignesh Raghavendra <vigneshr(a)ti.com> Sent: Monday, September 23, 2019 08:31 To: Eugeniy Paltsev Cc: uboot-snps-arc(a)synopsys.com; Alexey Brodkin Subject: Re: [U-Boot] Regressions in MTD / SPI FLASH Hi Eugeniy On 12/09/19 5:59 PM, Eugeniy Paltsev wrote: > Hi Vignesh, > > I doesn't have access to board with n25q512ax3 currently, however I can test this on Monday (16.09) Could you provide please provide logs that I requested below? " > Could you enable CONFIG_SPI_FLASH_SFDP_SUPPORT and also enable debug > prints in spi_mem_exec_op() (in drivers/spi/spi-mem.c like before) and > provide logs? " There are some objections to the fixes[1] that I provided to you. Above logs will helps me in justifying the fix or provide better patch. I would like to close this as soon as possible before 2019.10 is out. Appreciate you help! [1] https://urldefense.proofpoint.com/v2/url?u=http-3A__patchwork.ozlabs.org_pa… > > --- > Eugeniy Paltsev > > > ________________________________________ > From: Vignesh Raghavendra <vigneshr(a)ti.com> > Sent: Tuesday, September 10, 2019 15:27 > To: Eugeniy Paltsev; Jagan Teki > Cc: u-boot(a)lists.denx.de; Alexey Brodkin; trini(a)konsulko.com; uboot-snps-arc(a)synopsys.com > Subject: Re: [U-Boot] Regressions in MTD / SPI FLASH > > Hi Eugeniy, > > One more request: > > I am trying to find a better way to identify parts that don't support > 4byte addressing. > > Could you enable CONFIG_SPI_FLASH_SFDP_SUPPORT and also enable debug > prints in spi_mem_exec_op() (in drivers/spi/spi-mem.c like before) and > provide logs? > > Just logs of "sf probe" should be sufficient. > > Regards > Vignesh > > On 10/09/19 5:24 PM, Vignesh Raghavendra wrote: >> >> >> On 10/09/19 5:11 PM, Eugeniy Paltsev wrote: >>> Hi Vignesh, >>> >>> that patch helps - both erase and write works fine. >>> >> >> Thanks for testing! I will cleanup the patches and send formal patches >> to the list with your tested by. >> >> Regards >> Vignesh >> >>> For n25q512ax3: >>> Tested-by: "Eugeniy Paltsev <paltsev(a)synopsys.com>" >>> >>> --- >>> Eugeniy Paltsev >>> >>> >>> ________________________________________ >>> From: Vignesh Raghavendra <vigneshr(a)ti.com> >>> Sent: Tuesday, September 10, 2019 08:07 >>> To: Eugeniy Paltsev; Jagan Teki >>> Cc: u-boot(a)lists.denx.de; uboot-snps-arc(a)synopsys.com; Alexey Brodkin; trini(a)konsulko.com >>> Subject: Re: Regressions in MTD / SPI FLASH >>> >>> Hi, >>> >>> On 10/09/19 12:18 AM, Eugeniy Paltsev wrote: >>>> Hi! >>>> Comments are inlined: >>>> >>>>> On 04/09/19 11:37 PM, Eugeniy Paltsev wrote: >>>>>> We faced with regressions caused by >>>>>> commit c4e8862308d4 (mtd: spi: Switch to new SPI NOR framework) >>>>>> This switch was performed by removing entire u-boot spi-flash >>>>>> core implementation and copying it from another project. >>>>>> However the switch is performed without proper testing and >>>>>> investigations about fixes/improvements were made in u-boot >>>>>> spi-flash core. This results in regressions. >>>>>> >>>>> >>>>> Apologies for the trouble... >>>>> As stated in cover letter, this change was necessary as U-Boot SPI flash >>>>> stack at that time did not features such as 4 byte addressing, SFDP >>>>> parsing, SPI controllers with MMIO interfaces etc. Also there was need >>>>> to move to SPI MEM framework to support both SPI NAND and SPI NOR >>>>> flashes using a single SPI controller drivers. >>>>> I have to disagree on the part that there was no proper testing... As >>>>> evident from mailing list archives, patch series was reviewed by >>>>> multiple reviewers and tested on their platforms as well... >>>>> Unfortunately its impossible to get all boards owners to test it. >>>> >>>> I'm not talking about getting all customers board and testing changes on them. >>>> It could be done another way - i.e. like it is done for u-boot driver-model migration: >>>> by introducing the option for choosing which stack will be used and allow customers >>>> to switch the flash IC they use to new stack until some deadline. >>>> >>> >>> I did start off with this. But maintaining two stacks is too cumbersome >>> and adds to code size (which is a big factor for SPL stage) >>> >>> >>>>>> One of regression we faced with is related to SST26 flash series which >>>>>> is used on HSDK board. The cause is that SST26 protection ops >>>>>> implementation was dropped. The fix of this regression is send >>>>>> as a patch in this series. >>>>>> >>>>> >>>>> I retained most U-Boot specific code as is (like support for BANK >>>>> address registers, restriction in transfer sizes) but I somehow >>>>> overlooked this part. Sorry for that >>>>> >>>>>> However there are another regressions. I.E: we also faced with broken >>>>>> SPI flash on another SNPS boards - AXS101 and AXS103. They use different >>>>>> flash IC (n25q512ax3) and I didn't investigate the cause yet. >>>>>> >>>>> >>>>> Could you provide more details here: >>>>> What exactly fails? Is the detected correctly? Does reads work fine? Is >>>>> Erase or Write broken? >>>> >>>> It seems to me that something is wrong with protection ops. >>>> The erase and write finish without errors however nothing actually happens. >>>> >>> >>> I doubt so, because if the blocks were protected, erase/write would have failed >>> and Read status/Read flag status register should have reported error values. >>> Anyways, I guess I found a wrt how 4 Byte addressing is handled wrt n25q512* series. >>> >>> Could you try with below patch helps[1]? >>> If not please provide logs similar what you have provide now. >>> >>> If below patch does not help, then please try enabling CONFIG_SPI_FLASH_BAR and see if that helps. >>> >>> [1] >>> >>> ---8<----- >>> >>> From 1de4c447cd4b2590c98f9ceccf8ed32029b42d36 Mon Sep 17 00:00:00 2001 >>> From: Vignesh Raghavendra <vigneshr(a)ti.com> >>> Date: Tue, 10 Sep 2019 10:25:17 +0530 >>> Subject: [TST PATCH] mtd: spi: spi-nor-ids: Disable SPI_NOR_4B_OPCODES >>> >>> Not all variants of n25q256* and n25q512* support 4 Byte stateless >>> addressing and there is no easy way to discover this at runtime. >>> Therefore don't set SPI_NOR_4B_OPCODES for these flashes >>> >>> Signed-off-by: Vignesh Raghavendra <vigneshr(a)ti.com> >>> --- >>> drivers/mtd/spi/spi-nor-ids.c | 10 ++++------ >>> 1 file changed, 4 insertions(+), 6 deletions(-) >>> >>> diff --git a/drivers/mtd/spi/spi-nor-ids.c b/drivers/mtd/spi/spi-nor-ids.c >>> index a3920ba520e0..66ac3256e8f5 100644 >>> --- a/drivers/mtd/spi/spi-nor-ids.c >>> +++ b/drivers/mtd/spi/spi-nor-ids.c >>> @@ -161,12 +161,10 @@ const struct flash_info spi_nor_ids[] = { >>> { INFO("n25q064a", 0x20bb17, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_QUAD_READ) }, >>> { INFO("n25q128a11", 0x20bb18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) }, >>> { INFO("n25q128a13", 0x20ba18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) }, >>> - { INFO("n25q256a", 0x20ba19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) }, >>> - { INFO("n25q256ax1", 0x20bb19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) }, >>> - { INFO6("mt25qu512a", 0x20bb20, 0x104400, 64 * 1024, 1024, >>> - SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) }, >>> - { INFO("n25q512a", 0x20bb20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) }, >>> - { INFO("n25q512ax3", 0x20ba20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) }, >>> + { INFO("n25q256a", 0x20ba19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, >>> + { INFO("n25q256ax1", 0x20bb19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_QUAD_READ) }, >>> + { INFO("n25q512a", 0x20bb20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) }, >>> + { INFO("n25q512ax3", 0x20ba20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) }, >>> { INFO("n25q00", 0x20ba21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) }, >>> { INFO("n25q00a", 0x20bb21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) }, >>> { INFO("mt25qu02g", 0x20bb22, 0, 64 * 1024, 4096, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) }, >>> -- >>> 2.23.0 >>> >> > > -- > Regards > Vignesh > -- Regards Vignesh

2 1

[U-Boot] [PATCH v1] armv8: fsl-layerscape: LS1044A/1048A: enable Only 1x 10GE port
by Pramod Kumar 25 Sep '19

25 Sep '19

LS1044A/1048A is LS1088 personality which support only one 1x 10GE port. MAC1 and MAC2 are associated with 1G SGMII, 2.5G SGMII, and XFI. Disable MAC1 to have only one 1x 10GE port Signed-off-by: Pramod Kumar <pramod.kumar_1(a)nxp.com> --- arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c | 33 +++++++++++++++++++++- 1 file changed, 32 insertions(+), 1 deletion(-) diff --git a/arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c b/arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c index 8e8b45a..11090e8 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c +++ b/arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c @@ -5,6 +5,11 @@ #include <common.h> #include <asm/arch/fsl_serdes.h> +#include <asm/arch/soc.h> +#include <asm/io.h> +#define PERSONALITY_LS1088A_TYPE 0 +#define PERSONALITY_LS1044A_LS1048A_TYPE 1 +#define PERSONALITY_INVALID_TYPE -1 struct serdes_config { u8 ip_protocol; @@ -32,6 +37,7 @@ static struct serdes_config serdes1_cfg_tbl[] = { {0x3A, {SGMII3, PCIE1, SGMII1, SGMII2 }, {3, 5, 3, 3 } }, {} }; + static struct serdes_config serdes2_cfg_tbl[] = { /* SerDes 2 */ {0x0C, {PCIE1, PCIE1, PCIE1, PCIE1 }, {8, 8, 8, 8 } }, @@ -48,6 +54,22 @@ static struct serdes_config *serdes_cfg_tbl[] = { serdes2_cfg_tbl, }; +int check_personality_type(void) +{ + struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); + unsigned int svr, ver; + int personality; + + svr = gur_in32(&gur->svr); + ver = SVR_SOC_VER(svr); + if (ver == SVR_LS1088A) + personality = PERSONALITY_LS1088A_TYPE; + else + personality = PERSONALITY_LS1044A_LS1048A_TYPE; + + return personality; +} + int serdes_get_number(int serdes, int cfg) { struct serdes_config *ptr; @@ -84,10 +106,19 @@ int serdes_get_number(int serdes, int cfg) enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane) { struct serdes_config *ptr; + int personality_type; if (serdes >= ARRAY_SIZE(serdes_cfg_tbl)) return 0; - + /* + * LS1044A/1048A support only one XFI port + * Disable MAC1 for LS1044A/1048A + */ + if (!serdes && lane == 2) { + personality_type = check_personality_type(); + if (personality_type == PERSONALITY_LS1044A_LS1048A_TYPE) + return 0; + } ptr = serdes_cfg_tbl[serdes]; while (ptr->ip_protocol) { if (ptr->ip_protocol == cfg) -- 2.7.4

2 1

[U-Boot] envtools with tools-only_defconfig fails to build after v2019.10-rc1
by Vagrant Cascadian 24 Sep '19

24 Sep '19

I've been unable to successfully run "make envtools" on recent versions of u-boot, and finally got a chance to git bisect it. It looks like commit 9fb625ce05539fe6876a59ce1dcadb76b33c6f6e, introduced after 2019.10-rc1, breaks building envtools: #!/bin/sh # test-bisect set -e set -x make clean make tools-only_defconfig make NO_SDL=1 envtools .... Bisecting: 8 revisions left to test after this (roughly 3 steps) [9fb625ce05539fe6876a59ce1dcadb76b33c6f6e] env: Move env_set() to env.h running ../test-bisect + make clean CLEAN u-boot.cfg + make tools-only_defconfig HOSTCC scripts/basic/fixdep HOSTCC scripts/kconfig/conf.o YACC scripts/kconfig/zconf.tab.c LEX scripts/kconfig/zconf.lex.c HOSTCC scripts/kconfig/zconf.tab.o HOSTLD scripts/kconfig/conf # # configuration written to .config # + make NO_SDL=1 envtools scripts/kconfig/conf --syncconfig Kconfig CHK include/config.h CFG u-boot.cfg GEN include/autoconf.mk GEN include/autoconf.mk.dep CHK include/config/uboot.release UPD include/config/uboot.release CHK include/generated/version_autogenerated.h UPD include/generated/version_autogenerated.h CHK include/generated/timestamp_autogenerated.h UPD include/generated/timestamp_autogenerated.h LD tools/env/built-in.o HOSTCC tools/env/crc32.o HOSTCC tools/env/ctype.o HOSTCC tools/env/env_attr.o HOSTCC tools/env/env_flags.o In file included from tools/env/../../env/flags.c:7, from tools/env/env_flags.c:1: include/env.h:97:1: error: unknown type name 'ulong'; did you mean 'long'? 97 | ulong env_get_ulong(const char *name, int base, ulong default_val); | ^~~~~ | long include/env.h:97:49: error: unknown type name 'ulong'; did you mean 'long'? 97 | ulong env_get_ulong(const char *name, int base, ulong default_val); | ^~~~~ | long include/env.h:106:40: error: unknown type name 'ulong'; did you mean 'long'? 106 | int env_set_ulong(const char *varname, ulong value); | ^~~~~ | long include/env.h:118:1: error: unknown type name 'ulong'; did you mean 'long'? 118 | ulong env_get_hex(const char *varname, ulong default_val); | ^~~~~ | long include/env.h:118:40: error: unknown type name 'ulong'; did you mean 'long'? 118 | ulong env_get_hex(const char *varname, ulong default_val); | ^~~~~ | long include/env.h:127:38: error: unknown type name 'ulong'; did you mean 'long'? 127 | int env_set_hex(const char *varname, ulong value); | ^~~~~ | long include/env.h: In function 'env_set_addr': include/env.h:138:31: error: 'ulong' undeclared (first use in this function) 138 | return env_set_hex(varname, (ulong)addr); | ^~~~~ include/env.h:138:31: note: each undeclared identifier is reported only once for each function it appears in include/env.h:138:37: error: expected ')' before 'addr' 138 | return env_set_hex(varname, (ulong)addr); | ^~~~ | ) make[1]: *** [scripts/Makefile.host:114: tools/env/env_flags.o] Error 1 make: *** [Makefile:1778: envtools] Error 2 Bisecting: 3 revisions left to test after this (roughly 2 steps) ... Bisecting: 0 revisions left to test after this (roughly 0 steps) [cdbff9fc4002fdd47181088d5abe90e5f2fa1904] env: Move env_get_hex() to ... 9fb625ce05539fe6876a59ce1dcadb76b33c6f6e is the first bad commit commit 9fb625ce05539fe6876a59ce1dcadb76b33c6f6e Author: Simon Glass <sjg(a)chromium.org> Date: Thu Aug 1 09:46:51 2019 -0600 env: Move env_set() to env.h Move env_set() over to the new header file. Acked-by: Joe Hershberger <joe.hershberger(a)ni.com> Signed-off-by: Simon Glass <sjg(a)chromium.org> Would be great to get this building again before 2019.10 release! live well, vagrant

4 8

[U-Boot] [PATCH] Revert "ARM: tegra: reserve unmapped RAM so EFI doesn't use it"
by Mian Yousaf Kaukab 24 Sep '19

24 Sep '19

This reverts commit 0797f7f0b7e1d7853e2842ddc235ffef139fa792. Tegra specific solution is not required any more as efi core has been made aware of ram_top with the following commit: 7b78d6438a efi_loader: Reserve unaccessible memory Signed-off-by: Mian Yousaf Kaukab <ykaukab(a)suse.de> --- arch/arm/mach-tegra/board2.c | 14 -------------- 1 file changed, 14 deletions(-) diff --git a/arch/arm/mach-tegra/board2.c b/arch/arm/mach-tegra/board2.c index f13bd256cc..07f54f0684 100644 --- a/arch/arm/mach-tegra/board2.c +++ b/arch/arm/mach-tegra/board2.c @@ -6,7 +6,6 @@ #include <common.h> #include <dm.h> -#include <efi_loader.h> #include <env.h> #include <errno.h> #include <ns16550.h> @@ -224,19 +223,6 @@ int board_early_init_f(void) int board_late_init(void) { -#if CONFIG_IS_ENABLED(EFI_LOADER) - if (gd->bd->bi_dram[1].start) { - /* - * Only bank 0 is below board_get_usable_ram_top(), so all of - * bank 1 is not mapped by the U-Boot MMU configuration, and so - * we must prevent EFI from using it. - */ - efi_add_memory_map(gd->bd->bi_dram[1].start, - gd->bd->bi_dram[1].size >> EFI_PAGE_SHIFT, - EFI_BOOT_SERVICES_DATA, false); - } -#endif - #if defined(CONFIG_TEGRA_SUPPORT_NON_SECURE) if (tegra_cpu_is_non_secure()) { printf("CPU is in NS mode\n"); -- 2.16.4

3 2

[U-Boot] ROCK64 fails to boot using U-Boot TPL
by Simon South 24 Sep '19

24 Sep '19

I've been unable so far to boot NetBSD on my PINE64 ROCK64 (v2.0, Rockchip RK3328) using U-Boot built with its own TPL, the default since commit ff3dd0a474. The same NetBSD image boots fine using the binary TPL supplied by Rockchip. The exact failure varies but it always seems memory-related. Typically the NetBSD kernel fails right after starting with a panic in its virtual-memory system, uvm. Also significant may be these messages sometimes output by U-Boot at startup, which I haven't seen when the Rockchip TPL is used: libfdt fdt_check_header(): FDT_ERR_BADMAGIC I've pasted the output from a typical failed boot below and have submitted a problem report (with a bit more detail) to the NetBSD project: https://gnats.netbsd.org/54557 Does anyone know why this might be happening? Is there perhaps some additional setup the U-Boot TPL expects from the OS to finish configuring the RK3328's memory controller that's currently missing from NetBSD? How I can diagnose this further? ---------- U-Boot TPL 2019.10-rc3-00361-ga9fa70b7b7 (Sep 19 2019 - 03:11:29) LPDDR3 Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2019.10-rc3-00361-ga9fa70b7b7 (Sep 19 2019 - 03:11:29 -0400) Trying to boot from MMC2 Card did not respond to voltage select! spl: mmc init failed with error: -95 Trying to boot from MMC1 NOTICE: BL31: v2.1(release):v2.1-678-g2fc6ffc4-dirty NOTICE: BL31: Built : 12:10:07, Sep 12 2019 ERROR: over or zero region, nr=4187432, max=10 NOTICE: BL31:Rockchip release version: v1.2 U-Boot 2019.10-rc3-00361-ga9fa70b7b7 (Sep 19 2019 - 03:12:31 -0400) Model: Pine64 Rock64 DRAM: 4 GiB MMC: rksdmmc@ff500000: 1, rksdmmc@ff520000: 0 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@ff130000 Out: serial@ff130000 Err: serial@ff130000 Model: Pine64 Rock64 Net: Warning: ethernet@ff540000 (eth0) using random MAC address - da:e0:78:b1:50:d2 eth0: ethernet@ff540000 Hit any key to stop autoboot: 0 Card did not respond to voltage select! switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... 53513 bytes read in 9 ms (5.7 MiB/s) Found EFI removable media binary efi/boot/bootaa64.efi libfdt fdt_check_header(): FDT_ERR_BADMAGIC Scanning disk rksdmmc(a)ff500000.blk... Card did not respond to voltage select! Scanning disk rksdmmc(a)ff520000.blk... Disk rksdmmc(a)ff520000.blk not ready Found 3 disks BootOrder not defined EFI boot manager: Cannot load any image 205136 bytes read in 16 ms (12.2 MiB/s) libfdt fdt_check_header(): FDT_ERR_BADMAGIC - >> NetBSD/evbarm EFI Boot (aarch64), Revision 1.11 (Wed Sep 18 15:50:45 UTC 2019) (from NetBSD 9.99.12) Press return to boot now, any other key for boot prompt booting netbsd - starting in 0 seconds. 6100056+2730512+1985652+1823764+490622=0xec5b00 [ 1.0000000] NetBSD/evbarm (fdt) booting ... [ 1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, [ 1.0000000] 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, [ 1.0000000] 2018, 2019 The NetBSD Foundation, Inc. All rights reserved. [ 1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993 [ 1.0000000] The Regents of the University of California. All rights reserved. [ 1.0000000] NetBSD 9.99.12 (GENERIC64) #16: Wed Sep 18 12:30:03 EDT 2019 [ 1.0000000] ssouth@laptop:/usr/src/sys/arch/evbarm/compile/obj/GENERIC64 [ 1.0000000] total memory = 4064 MB [ 1.0000000] avail memory = 3918 MB [ 1.0000000] panic: kernel diagnostic assertion "ucpu == VM_FREE_PAGE_TO_CPU(pg)" failed: file "/usr/src/sys/uvm/uvm_page.c", line 852 [ 1.0000000] cpu0: Begin traceback... [ 1.0000000] trace fp ffffffc000bec8d0 [ 1.0000000] fp ffffffc000bec8f0 vpanic() at ffffffc0004924c0 netbsd:vpanic+0x198 [ 1.0000000] fp ffffffc000bec950 kern_assert() at ffffffc0005cdf24 netbsd:kern_assert+0x5c [ 1.0000000] fp ffffffc000bec9e0 uvm_pagealloc_pgfl() at ffffffc00040f388 netbsd:uvm_pagealloc_pgfl+0x5c8 [ 1.0000000] fp ffffffc000beca40 uvm_pagealloc_strat() at ffffffc000410034 netbsd:uvm_pagealloc_strat+0x18c [ 1.0000000] fp ffffffc000becad0 uvm_km_kmem_alloc() at ffffffc000403b30 netbsd:uvm_km_kmem_alloc+0x60 [ 1.0000000] fp ffffffc000becb40 pool_page_alloc() at ffffffc00048b0c0 netbsd:pool_page_alloc+0x28 [ 1.0000000] fp ffffffc000becb60 pool_grow() at ffffffc00048d294 netbsd:pool_grow+0x35c [ 1.0000000] fp ffffffc000becbd0 pool_get() at ffffffc00048c5e8 netbsd:pool_get+0xa0 [ 1.0000000] fp ffffffc000becc30 pool_cache_get_slow() at ffffffc00048e8a4 netbsd:pool_cache_get_slow+0x1dc [ 1.0000000] fp ffffffc000becc80 pool_cache_get_paddr() at ffffffc0004901e8 netbsd:pool_cache_get_paddr+0x258 [ 1.0000000] fp ffffffc000becce0 kmem_intr_alloc() at ffffffc0004859f0 netbsd:kmem_intr_alloc+0x60 [ 1.0000000] fp ffffffc000becd10 kmem_intr_zalloc() at ffffffc000485b20 netbsd:kmem_intr_zalloc+0x10 [ 1.0000000] fp ffffffc000becd30 kmem_zalloc() at ffffffc000485dc4 netbsd:kmem_zalloc+0x84 [ 1.0000000] fp ffffffc000becd50 module_builtin_add() at ffffffc0004432a0 netbsd:module_builtin_add+0x98 [ 1.0000000] fp ffffffc000becdf0 module_init() at ffffffc0004437f8 netbsd:module_init+0xf0 [ 1.0000000] fp ffffffc000bece50 main() at ffffffc0005d0b08 netbsd:main+0x108 [ 1.0000000] fp 0000000000000000 aarch64_start() at ffffffc00000183c netbsd:aarch64_start+0x103c [ 1.0000000] cpu0: End traceback... Stopped in pid 0.1 (system) at netbsd:cpu_Debugger+0x4: ret db{0}> -- Simon South simon(a)simonsouth.net

6 27

[U-Boot] [PATCH v2] Update MAINTAINERS to include environment files
by Joe Hershberger 24 Sep '19

24 Sep '19

To be maintained by me (Joe) and Wolfgang Denx Signed-off-by: Joe Hershberger <joe.hershberger(a)ni.com> --- Changes in v2: - Remove Wolfgang from listed maintainer MAINTAINERS | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index e752e4b3de..384ac26048 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -540,6 +540,15 @@ F: cmd/efidebug.c F: cmd/nvedit_efi.c F: tools/file2include.c +ENVIRONMENT +M: Joe Hershberger <joe.hershberger(a)ni.com> +S: Maintained +F: env/ +F: include/env* +F: test/env/ +F: tools/env* +F: tools/mkenvimage.c + FPGA M: Michal Simek <michal.simek(a)xilinx.com> S: Maintained -- 2.11.0

1 0

[U-Boot] [PATCH v4 00/15] splash screen on the stm32f769 & stm32mp1 boards
by Yannick Fertré 24 Sep '19

24 Sep '19

Version 1: - Initial commit. Version 2: - swap patches to avoid compilation issue. - remove panel timings from device tree. Version 3: - Share same include file mipi_display.h with kernel linux. - Rework ltdc driver with last comments of Anatolij Gustshin. - Check ordering (file dw_mipi_dsi.c). - Rename mipi_display.c to mipi_dsi.c. Version 4: - Add physical set mode operation - Improve debug trace (display controller ltdc) - Refresh timings of panels - Add regulator (dsi controller) - Add new class DSI_HOST - Support of panels OTM800A & RM68200 This serie contains all patchsets needed for displaying a splash screen on the stm32f769 & stm32mp1 boards. A new config has been created configs/stm32f769-disco_defconfig. This is necessary due to the difference of panels between stm32f769-disco, stm32f746-disco boards & stm32mp1 boards. A new class DSI_HOST have been created to manage a dsi host between the dsi controller & display controller. Yannick Fertré (15): video: bmp: check resolutions of panel/bitmap video: stm32: stm32_ltdc: add bridge to display controller include: Add new DCS commands in the enum list video: add support of MIPI DSI interface dm: Add a dsi host uclass video: add MIPI DSI host controller bridge video: add support of STM32 MIPI DSI controller driver video: add support of panel OTM8009A video: add support of panel RM68200 board: Add STM32F769 SoC, discovery board support ARM: dts: stm32f769: add display for STM32F769 disco board ARM: dts: stm32mp1: add dsi host for stm32mp157c-ev1 board ARM: dts: stm32mp1: add dsi host for stm32mp157c-dk2 board stm32mp1: configs: update video stm32mp1: configs: add display devices arch/arm/dts/stm32f769-disco-u-boot.dtsi | 62 +++ arch/arm/dts/stm32mp157c-dk2-u-boot.dtsi | 7 + arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi | 5 + arch/sandbox/dts/sandbox.dts | 6 +- configs/sandbox_defconfig | 1 + configs/stm32f769-disco_defconfig | 63 +++ configs/stm32mp15_basic_defconfig | 6 + configs/stm32mp15_optee_defconfig | 6 + configs/stm32mp15_trusted_defconfig | 6 + drivers/video/Kconfig | 43 ++ drivers/video/Makefile | 6 + drivers/video/dsi-host-uclass.c | 39 ++ drivers/video/dw_mipi_dsi.c | 838 +++++++++++++++++++++++++++++++ drivers/video/mipi_dsi.c | 828 ++++++++++++++++++++++++++++++ drivers/video/orisetech_otm8009a.c | 379 ++++++++++++++ drivers/video/raydium-rm68200.c | 351 +++++++++++++ drivers/video/sandbox_dsi_host.c | 83 +++ drivers/video/stm32/Kconfig | 9 + drivers/video/stm32/Makefile | 1 + drivers/video/stm32/stm32_dsi.c | 490 ++++++++++++++++++ drivers/video/stm32/stm32_ltdc.c | 143 +++--- drivers/video/video_bmp.c | 14 + include/configs/stm32mp1.h | 7 + include/dm/uclass-id.h | 1 + include/dsi_host.h | 57 +++ include/mipi_display.h | 8 + include/mipi_dsi.h | 466 +++++++++++++++++ test/dm/Makefile | 1 + test/dm/dsi_host.c | 58 +++ 29 files changed, 3923 insertions(+), 61 deletions(-) create mode 100644 configs/stm32f769-disco_defconfig create mode 100644 drivers/video/dsi-host-uclass.c create mode 100644 drivers/video/dw_mipi_dsi.c create mode 100644 drivers/video/mipi_dsi.c create mode 100644 drivers/video/orisetech_otm8009a.c create mode 100644 drivers/video/raydium-rm68200.c create mode 100644 drivers/video/sandbox_dsi_host.c create mode 100644 drivers/video/stm32/stm32_dsi.c create mode 100644 include/dsi_host.h create mode 100644 include/mipi_dsi.h create mode 100644 test/dm/dsi_host.c -- 2.7.4

4 19

[U-Boot] [PATCH v2 0/3] imx6ull: Fix missing initial output from UART
by Igor Opaniuk 24 Sep '19

24 Sep '19

For Colibri iMX6ULL we have to set pinmux for uart configuration ASAP (ideally before relocation) to get serial console working. Without this we miss almost the half of output (U-boot version, CPU defails, Reset cause, DRAM details etc.). To achieve this we need to force pinctrl-mx6 to get probed before relocation and add u-boot,dm-pre-reloc properties to uart pinmux configuration nodes. Setting pinmux configuration for UART before was done in board_early_init_f(). Igor Opaniuk (3): pinctrl: nxp: DM_FLAG_PRE_RELOC by default ARM: dts: imx6ull-colibri: change hierarchy of DTS files ARM: dts: imx6ull-colibri: pre-reloc for uart pinmux modes v2: - Addressed comments [Fabio Estevam] arch/arm/dts/imx6ull-colibri-u-boot.dtsi | 12 + arch/arm/dts/imx6ull-colibri.dts | 596 +------------------- arch/arm/dts/imx6ull-colibri.dtsi | 641 ++++++++++++++++++++++ board/toradex/colibri-imx6ull/MAINTAINERS | 2 + drivers/pinctrl/nxp/pinctrl-imx5.c | 2 - drivers/pinctrl/nxp/pinctrl-imx6.c | 2 - drivers/pinctrl/nxp/pinctrl-imx7.c | 2 - drivers/pinctrl/nxp/pinctrl-imx7ulp.c | 2 - 8 files changed, 657 insertions(+), 602 deletions(-) create mode 100644 arch/arm/dts/imx6ull-colibri-u-boot.dtsi create mode 100644 arch/arm/dts/imx6ull-colibri.dtsi -- 2.17.1

5 11

[U-Boot] [PATCH v1 0/3] Add support for DFU boot to DRA7-based EVMs
by Jean-Jacques Hiblot 24 Sep '19

24 Sep '19

The purpose of this series is to provide the SPL with ability to boot u-boot from DFU. The DRA7x can download the SPL over the USB1 port when configured in the USB peripheral boot mode. Details on how this can be acheived with the EVMs can found here http://www.ti.com/lit/an/sprac33/sprac33.pdf Once the SPL is loaded, u-boot can be downloaded on the same USB1 port through DFU. This boot flow has been tested on DRA7-evm, DRA72-evm-rec, DRA71-evm and DRA76-evm Faiz Abbas (3): ARM: dts: dra7: Add usb peripheral nodes in spl configs: dra7xx_evm: Add Kconfigs for SPL_DFU bootmode configs: dra7xx_evm: Increase the size of SPL_MULTI_DTB_FIT arch/arm/dts/dra7-evm-u-boot.dtsi | 17 +++++++++++++++++ arch/arm/dts/dra71-evm-u-boot.dtsi | 17 +++++++++++++++++ arch/arm/dts/dra72-evm-revc-u-boot.dtsi | 17 +++++++++++++++++ arch/arm/dts/dra72-evm-u-boot.dtsi | 23 +++++++++++++++++++++++ arch/arm/dts/dra76-evm-u-boot.dtsi | 17 +++++++++++++++++ arch/arm/dts/omap5-u-boot.dtsi | 1 + configs/dra7xx_evm_defconfig | 8 +++++++- configs/dra7xx_hs_evm_defconfig | 8 +++++++- 8 files changed, 106 insertions(+), 2 deletions(-) create mode 100644 arch/arm/dts/dra72-evm-u-boot.dtsi -- 2.17.1

1 3

[U-Boot] [GIT PULL] Pull request: u-boot-imx u-boot-imx-20190923
by Stefano Babic 24 Sep '19

24 Sep '19

Hi Tom, please pull from u-boot-imx, thanks ! The following changes since commit 87d5b225585f341ea8e926a2c26fb72585fc9d0c: MAINTAINERS: Change fsl-qoriq, mpc86xx, mpc85xx maintainers (2019-09-13 10:14:45 -0400) are available in the Git repository at: https://gitlab.denx.de/u-boot/custodians/u-boot-imx.git tags/u-boot-imx-20190923 for you to fetch changes up to 322a967cdf470640cb8cb6b68b6721e63b8c3104: Merge branch 'for-imx' of https://github.com/OSSystems/u-boot (2019-09-22 15:19:49 +0200) ---------------------------------------------------------------- u-boot-imx-20190923 ------------------- - Fixes i.MX7ULP - No default CSF size in case of SECURE_BOOT - Technexion boards - Nitrogen boards ported to DM - fix for mx53loco - Sync DTS for i.MX6UL(L) - Fuses for i.MX7ULP - i.mx8 : container image, fixes - Fixes for Toradex (apalis) - SPL: allow bigger size for i.MX6Q/D Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/588095906 ---------------------------------------------------------------- Anatolij Gustschin (1): imx: sksimx6_defconfig: remove SPL misc option to fix build error Bai Ping (2): i.MX7ULP: Fix system reset after a7 rtc alarm expired. i.MX7ULP: Correct the clock index Breno Matheus Lima (4): Kconfig: Migrate CONFIG_CSF_SIZE to Kconfig imx6: spl: Reduce SPL limit size in case CONFIG_SECURE_BOOT is enabled imx: configs: Cleanup CONFIG_SECURE_BOOT comments habv4: tools: Avoid hardcoded CSF size for SPL targets Fabio Berton (1): pico-imx7d: Sync pico-hobbit-imx7d_defconfig Fabio Estevam (15): mx6sabresd: Reduce overall SPL size pico-imx6ul: Increase the CONFIG_ENV_OFFSET size pico-imx6ul: Add LCD support pico-imx6ul: Update the Falcon mode instructions pico-imx6ul: Provide a way to escape the Falcon mode pico-imx7d: Add instructions for booting in Falcon mode pico-imx7d: Provide a way to escape the Falcon mode logos: Add the TechNexion's logo pico: Convert to CONFIG_FSL_USDHC mx53loco: Fix U-Boot corruption after saving the environment mx6: clock: Allow enable_ipu_clock() to be built for SPL code pico-imx6: Add initial support pico-imx6: Add Ethernet support pico-imx6: Add splashscreen support pico-imx6: Add Falcon mode Joris Offouga (3): ARM: dts: pico-imx7d: Add u-boot.dtsi for uboot specific dts change ARM: dts: pico-imx7d: sync device tree with v5.3-rc6 configs: pico-imx7d: Convert to DM_VIDEO Otavio Salvador (5): pico-imx6ul: Add DWARF baseboard support pico-imx7d: Add DWARF baseboard support pico-imx7d: Add NYMPH baseboard support configs: Sync all baseboard specific pico-imx7d pico-imx6: Fix bootmenu handling Peng Fan (39): arm: dts: sync dts for i.MX6UL arm: dts: sync dts for i.MX6ULL arm: dts: import dts for i.MX6ULZ imx: add i.MX6ULZ cpu type imx: add i.MX6ULZ board imx: mx6ul_14x14_evk: Fix SPL boot imx: mx6ul_14x14_evk: convert to DM_VIDEO imx: mx6slevk: enable DM_SPI and DM_SPI_FLASH pinctrl: imx: use devfdt_get_addr_size_index tools: imx8mimage: fix HDMI/FIT parsing serial: Kconfig: make MXC_UART usable for MX7 and IMX8M spl: pass args to board_return_to_bootrom arm: dts: imx: fsl-imx8qm.dtsi: add gpio aliases to fix gpio command imx: i.MX7ULP: add get_boot_device i.MX7ULP: evk: Modify FDT file to disable SD3.0 for usb boot misc: Kconfig: make i.MX7ULP could use MXC_OCOTP i.MX7ULP: evk: Enable fuse comamnd i.MX7ULP: Add CPU revision check for B0 imx: mx6sabresd: fix usb start when DM enabled imx: imx6qdl: dtsi: move U-Boot specific change to u-boot.dtsi imx: imx8qxp_mek: fix CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR imx8: support parsing i.MX8 Container file spl: mmc: support loading i.MX container format file imx: add container target imx8qxp_mek: switch to use container image imx8qm_mek: switch to use container image doc: imx: mkimage: introduce i.MX8 image format imx: sys_proto: add is_imx8qm helper imx8qm: power up SMMU imx8qm: correct fdt_file imx8: disable node when the resource is not owned configs: imx8qm/qxp_mek: enable CONFIG_OF_SYSTEM_SETUP imx: scu_api: add sc_rm_set_master_sid imx8: fdt: configure sid for masters imx8: save args passed from ATF imx8: fdt: add optee node imx: scu_api: add sc_pm_is_partition_started imx8: move i.MX8 cpu desc code to drivers/cpu/imx8_cpu.c imx8: cpu: fix mac fuse word for i.MX8QM Ricardo Salveti (4): apalis_imx6: add board_fit_config_name_match to support FIT in SPL apalis_imx6: fix broken fsl_esdhc_imx conversion imx: apalis_imx6: select MX6Q via Kconfig spl: imx: only use HAB if spl fit signature is not enabled Robert Hancock (1): ARM: imx: Support larger SPL size on IMX6DQ Stefano Babic (5): Merge branch 'nxp-imx-8-13' of https://github.com/MrVan/u-boot into master-next Revert "habv4: tools: Avoid hardcoded CSF size for SPL targets" imx: fix missing MAINTAINERS pico boards board: imx6dl_mamoj: set the value for CSF size Merge branch 'for-imx' of https://github.com/OSSystems/u-boot Troy Kisky (5): nitrogen6x: migrate to using device tree configs: nitrogen6x: Add DM_MMC/DM_USB/AHCI support nitrogen6x: reserve used gpios configs: nitrogen6x: Add DM_GPIO support configs: nitrogen6x: Add DM_SPI/DM_SPI_FLASH support Ye Li (8): i.MX7ULP: Fix PCC register bits mask and offset issue i.MX7ULP: Add CONFIG_MX7ULP to kconfig i.MX7ULP: Fix wrong i2c configuration name i.MX7ULP: Fix SPLL/APLL clock rate calculation issue i.MX7ULP: Workaround APLL PFD2 to 345.6Mhz i.MX7ULP: Set A7 core frequency to 500Mhz for B0 chip i.MX7ULP: Change clock rate calculation for NIC1 BUS and EXT imx8: Probe the SCU driver by using uclass function Makefile | 8 +++ arch/arm/cpu/arm926ejs/spear/spl.c | 5 +- arch/arm/dts/Makefile | 32 ++++++--- arch/arm/dts/fsl-imx8qm.dtsi | 7 ++ arch/arm/dts/imx6dl-nitrogen6x.dts | 15 +++++ arch/arm/dts/imx6dl-pico.dts | 17 +++++ arch/arm/dts/imx6q-nitrogen6x.dts | 19 ++++++ arch/arm/dts/imx6q-pico.dts | 17 +++++ arch/arm/dts/imx6q-sabrelite.dts | 19 ++++++ arch/arm/dts/imx6qdl-nitrogen6x.dtsi | 69 +++++++++++++++++++ arch/arm/dts/imx6qdl-pico.dtsi | 424 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ arch/arm/dts/imx6qdl-sabrelite.dtsi | 384 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ arch/arm/dts/imx6qdl-u-boot.dtsi | 6 ++ arch/arm/dts/imx6qdl.dtsi | 3 - arch/arm/dts/imx6ul-14x14-evk-u-boot.dtsi | 49 +++++++++++++- arch/arm/dts/imx6ul-14x14-evk.dts | 422 ++----------------------------------------------------------------------------------------------------------------- arch/arm/dts/imx6ul-14x14-evk.dtsi | 531 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ arch/arm/dts/imx6ul-pinfunc.h | 175 +++++++++++++++++++++++++++--------------------- arch/arm/dts/imx6ul.dtsi | 301 ++++++++++++++++++++++++++++++++++++++++++++++++++++++---------------------------- arch/arm/dts/imx6ull-14x14-evk.dts | 523 ++-------------------------------------------------------------------------------------------------------------------------------------------- arch/arm/dts/imx6ull-pinfunc-snvs.h | 7 +- arch/arm/dts/imx6ull-pinfunc.h | 116 ++++++++++++++++++++------------ arch/arm/dts/imx6ull.dtsi | 1184 +++++++++++++-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- arch/arm/dts/imx6ulz-14x14-evk.dts | 22 ++++++ arch/arm/dts/imx6ulz.dtsi | 37 +++++++++++ arch/arm/dts/imx7d-pico-u-boot.dtsi | 124 ++++++++++++++++++++++++++++++++++ arch/arm/dts/imx7d-pico.dtsi | 10 +-- arch/arm/include/asm/arch-imx/cpu.h | 1 + arch/arm/include/asm/arch-imx8/image.h | 56 ++++++++++++++++ arch/arm/include/asm/arch-imx8/sci/rpc.h | 5 +- arch/arm/include/asm/arch-imx8/sci/sci.h | 2 + arch/arm/include/asm/arch-imx8/sys_proto.h | 1 + arch/arm/include/asm/arch-mx7ulp/clock.h | 2 +- arch/arm/include/asm/arch-mx7ulp/imx-regs.h | 20 ++++++ arch/arm/include/asm/arch-mx7ulp/pcc.h | 4 +- arch/arm/include/asm/arch-mx7ulp/scg.h | 1 + arch/arm/include/asm/arch-mx7ulp/sys_proto.h | 1 + arch/arm/include/asm/mach-imx/sys_proto.h | 2 + arch/arm/mach-imx/Kconfig | 7 ++ arch/arm/mach-imx/Makefile | 14 +++- arch/arm/mach-imx/cpu.c | 2 + arch/arm/mach-imx/imx8/Kconfig | 13 ++++ arch/arm/mach-imx/imx8/Makefile | 7 +- arch/arm/mach-imx/imx8/cpu.c | 189 ++++------------------------------------------------ arch/arm/mach-imx/imx8/fdt.c | 292 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ arch/arm/mach-imx/imx8/lowlevel_init.S | 36 ++++++++++ arch/arm/mach-imx/imx8/parse-container.c | 120 +++++++++++++++++++++++++++++++++ arch/arm/mach-imx/mx6/Kconfig | 21 ++++++ arch/arm/mach-imx/mx6/clock.c | 32 ++++----- arch/arm/mach-imx/mx6/soc.c | 4 ++ arch/arm/mach-imx/mx7ulp/Kconfig | 6 +- arch/arm/mach-imx/mx7ulp/clock.c | 8 ++- arch/arm/mach-imx/mx7ulp/scg.c | 63 ++++++++++++++++-- arch/arm/mach-imx/mx7ulp/soc.c | 38 ++++++++++- arch/arm/mach-imx/spl.c | 2 + arch/arm/mach-rockchip/spl.c | 5 +- arch/arm/mach-rockchip/tpl.c | 5 +- board/boundary/nitrogen6x/MAINTAINERS | 5 ++ board/boundary/nitrogen6x/nitrogen6x.c | 30 ++++++++- board/freescale/imx8qm_mek/README | 4 +- board/freescale/imx8qm_mek/uboot-container.cfg | 13 ++++ board/freescale/imx8qxp_mek/README | 4 +- board/freescale/imx8qxp_mek/uboot-container.cfg | 13 ++++ board/freescale/mx6slevk/mx6slevk.c | 28 -------- board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c | 73 ++++++-------------- board/freescale/mx6ullevk/MAINTAINERS | 1 + board/freescale/mx6ullevk/mx6ullevk.c | 10 ++- board/freescale/mx7ulp_evk/mx7ulp_evk.c | 47 +++++++++++++ board/technexion/pico-imx6/Kconfig | 15 +++++ board/technexion/pico-imx6/MAINTAINERS | 9 +++ board/technexion/pico-imx6/Makefile | 5 ++ board/technexion/pico-imx6/README | 73 ++++++++++++++++++++ board/technexion/pico-imx6/pico-imx6.c | 362 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ board/technexion/pico-imx6/spl.c | 314 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ board/technexion/pico-imx6ul/README | 8 +-- board/technexion/pico-imx6ul/pico-imx6ul.c | 55 ++++++++++++++- board/technexion/pico-imx6ul/spl.c | 4 ++ board/technexion/pico-imx7d/MAINTAINERS | 2 + board/technexion/pico-imx7d/README | 91 +++++++++++++++++++++++++ board/technexion/pico-imx7d/pico-imx7d.c | 48 +++++-------- board/technexion/pico-imx7d/spl.c | 4 ++ board/toradex/apalis_imx6/apalis_imx6.c | 14 +++- common/spl/Kconfig | 3 +- common/spl/spl_bootrom.c | 7 +- common/spl/spl_mmc.c | 10 +++ configs/imx6dl_mamoj_defconfig | 3 +- configs/imx8mq_evk_defconfig | 1 + configs/imx8qm_mek_defconfig | 9 ++- configs/imx8qxp_mek_defconfig | 6 +- configs/mx6qsabrelite_defconfig | 10 ++- configs/mx6sabresd_defconfig | 4 +- configs/mx6slevk_defconfig | 2 + configs/mx6slevk_spinor_defconfig | 2 + configs/mx6slevk_spl_defconfig | 2 + configs/mx6ul_14x14_evk_defconfig | 2 +- configs/mx6ul_9x9_evk_defconfig | 2 +- configs/mx6ulz_14x14_evk_defconfig | 44 ++++++++++++ configs/mx7ulp_evk_defconfig | 3 + configs/mx7ulp_evk_plugin_defconfig | 2 + configs/nitrogen6dl2g_defconfig | 11 ++- configs/nitrogen6dl_defconfig | 11 ++- configs/nitrogen6q2g_defconfig | 11 ++- configs/nitrogen6q_defconfig | 11 ++- configs/nitrogen6s1g_defconfig | 11 ++- configs/nitrogen6s_defconfig | 11 ++- configs/pico-dwarf-imx6ul_defconfig | 65 ++++++++++++++++++ configs/pico-dwarf-imx7d_defconfig | 69 +++++++++++++++++++ configs/pico-hobbit-imx6ul_defconfig | 1 + configs/pico-hobbit-imx7d_defconfig | 6 +- configs/pico-imx6_defconfig | 73 ++++++++++++++++++++ configs/pico-imx6ul_defconfig | 1 + configs/pico-imx7d_bl33_defconfig | 2 +- configs/pico-imx7d_defconfig | 2 +- configs/pico-nymph-imx7d_defconfig | 69 +++++++++++++++++++ configs/pico-pi-imx6ul_defconfig | 1 + configs/pico-pi-imx7d_defconfig | 4 +- configs/sksimx6_defconfig | 1 - doc/imx/mkimage/imx8image.txt | 45 +++++++++++++ drivers/cpu/Makefile | 1 + drivers/cpu/imx8_cpu.c | 182 ++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/misc/Kconfig | 2 +- drivers/misc/imx8/scu_api.c | 49 ++++++++++++++ drivers/pinctrl/nxp/pinctrl-imx.c | 4 +- drivers/serial/Kconfig | 2 +- include/configs/cl-som-imx7.h | 4 -- include/configs/imx6_spl.h | 28 +++++++- include/configs/imx8mq_evk.h | 4 -- include/configs/imx8qm_mek.h | 2 +- include/configs/imx8qxp_mek.h | 2 +- include/configs/mx53loco.h | 14 +++- include/configs/mx6_common.h | 4 -- include/configs/mx6sllevk.h | 6 -- include/configs/mx6ul_14x14_evk.h | 2 +- include/configs/mx6ullevk.h | 19 ++++-- include/configs/mx7_common.h | 4 -- include/configs/mx7ulp_evk.h | 9 --- include/configs/pico-imx6.h | 164 +++++++++++++++++++++++++++++++++++++++++++++ include/configs/pico-imx6ul.h | 33 ++++++++- include/configs/pico-imx7d.h | 8 ++- include/dt-bindings/clock/imx6ul-clock.h | 50 ++++++++------ include/spl.h | 15 ++++- scripts/config_whitelist.txt | 1 - tools/imx8mimage.c | 7 +- tools/logos/technexion.bmp | Bin 0 -> 22390 bytes tools/spl_size_limit.c | 3 + 145 files changed, 5083 insertions(+), 2770 deletions(-) create mode 100644 arch/arm/dts/imx6dl-nitrogen6x.dts create mode 100644 arch/arm/dts/imx6dl-pico.dts create mode 100644 arch/arm/dts/imx6q-nitrogen6x.dts create mode 100644 arch/arm/dts/imx6q-pico.dts create mode 100644 arch/arm/dts/imx6q-sabrelite.dts create mode 100644 arch/arm/dts/imx6qdl-nitrogen6x.dtsi create mode 100644 arch/arm/dts/imx6qdl-pico.dtsi create mode 100644 arch/arm/dts/imx6qdl-sabrelite.dtsi create mode 100644 arch/arm/dts/imx6ul-14x14-evk.dtsi create mode 100644 arch/arm/dts/imx6ulz-14x14-evk.dts create mode 100644 arch/arm/dts/imx6ulz.dtsi create mode 100644 arch/arm/dts/imx7d-pico-u-boot.dtsi create mode 100644 arch/arm/include/asm/arch-imx8/image.h create mode 100644 arch/arm/mach-imx/imx8/fdt.c create mode 100644 arch/arm/mach-imx/imx8/lowlevel_init.S create mode 100644 arch/arm/mach-imx/imx8/parse-container.c create mode 100644 board/freescale/imx8qm_mek/uboot-container.cfg create mode 100644 board/freescale/imx8qxp_mek/uboot-container.cfg create mode 100644 board/technexion/pico-imx6/Kconfig create mode 100644 board/technexion/pico-imx6/MAINTAINERS create mode 100644 board/technexion/pico-imx6/Makefile create mode 100644 board/technexion/pico-imx6/README create mode 100644 board/technexion/pico-imx6/pico-imx6.c create mode 100644 board/technexion/pico-imx6/spl.c create mode 100644 configs/mx6ulz_14x14_evk_defconfig create mode 100644 configs/pico-dwarf-imx6ul_defconfig create mode 100644 configs/pico-dwarf-imx7d_defconfig create mode 100644 configs/pico-imx6_defconfig create mode 100644 configs/pico-nymph-imx7d_defconfig create mode 100644 doc/imx/mkimage/imx8image.txt create mode 100644 drivers/cpu/imx8_cpu.c create mode 100644 include/configs/pico-imx6.h create mode 100644 tools/logos/technexion.bmp -- ===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic(a)denx.de =====================================================================

6 8