July 2019 - U-Boot

[U-Boot] [PATCH v1 0/2] stm32f7 gpio driver fixes
by Patrice Chotard 31 Mar '20

31 Mar '20

This series adds: - Fix gpio bank hole management for stm32 F7 and H7 - Fix SPL code size for stm32 F7 Patrice Chotard (2): gpio: stm32f7: Fix gpio bank hole management gpio: stm32f7: Fix SPL code size drivers/gpio/stm32f7_gpio.c | 22 +++++++++++++++++----- 1 file changed, 17 insertions(+), 5 deletions(-) -- 1.9.1

6 11

[U-Boot] [PATCH] usb: ehci-mx5: Fix bus enumeration for DM case
by Marek Vasut 29 Feb '20

29 Feb '20

It is likely that the DM conversion of EHCI iMX5 driver was a derivative of EHCI VF, however the conversion is incomplete and is missing the bind workaround, which updates dev->seq number. Without this, all controllers have dev->seq number 0 . Add this bind workaround into EHCI iMX5 driver as well. Signed-off-by: Marek Vasut <marex(a)denx.de> Cc: Abel Vesa <abel.vesa(a)nxp.com> Cc: Adam Ford <aford173(a)gmail.com> Cc: Fabio Estevam <festevam(a)gmail.com> Cc: Ludwig Zenz <lzenz(a)dh-electronics.com> Cc: Peng Fan <peng.fan(a)nxp.com> Cc: Stefano Babic <sbabic(a)denx.de> Cc: Vagrant Cascadian <vagrant(a)debian.org> --- drivers/usb/host/ehci-mx5.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/drivers/usb/host/ehci-mx5.c b/drivers/usb/host/ehci-mx5.c index 0b32728c57..4db513f4e5 100644 --- a/drivers/usb/host/ehci-mx5.c +++ b/drivers/usb/host/ehci-mx5.c @@ -301,6 +301,22 @@ static int ehci_usb_ofdata_to_platdata(struct udevice *dev) return 0; } +static int ehci_usb_bind(struct udevice *dev) +{ + static int num_controllers; + + /* + * Without this hack, if we return ENODEV for USB Controller 0, on + * probe for the next controller, USB Controller 1 will be given a + * sequence number of 0. This conflicts with our requirement of + * sequence numbers while initialising the peripherals. + */ + dev->req_seq = num_controllers; + num_controllers++; + + return 0; +} + static int ehci_usb_probe(struct udevice *dev) { struct usb_platdata *plat = dev_get_platdata(dev); @@ -362,6 +378,7 @@ U_BOOT_DRIVER(usb_mx5) = { .id = UCLASS_USB, .of_match = mx5_usb_ids, .ofdata_to_platdata = ehci_usb_ofdata_to_platdata, + .bind = ehci_usb_bind, .probe = ehci_usb_probe, .remove = ehci_deregister, .ops = &ehci_usb_ops, -- 2.20.1

2 5

[U-Boot] Starting u-boot in USB otg mode
by rivael_il 27 Feb '20

27 Feb '20

Hello u-booters! I want to load u-boot-sunxi-with-spl.bin and make it operate the USB in otg mode. (Where the host can still be connected to the board). How can I achieve this? (I have attempted to use: "usb0:dr_mode=otg,phy_type=utmi\0" without success). Thank you, Michael

5 11

[U-Boot] [PATCH 1/4 v4] watchdog: Implement generic watchdog_reset() version
by Stefan Roese 23 Feb '20

23 Feb '20

This patch tries to implement a generic watchdog_reset() function that can be used by all boards that want to service the watchdog device in U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG. Without this approach, new boards or platforms needed to implement a board specific version of this functionality, mostly copy'ing the same code over and over again into their board or platforms code base. With this new generic function, the scattered other functions are now removed to be replaced by the generic one. The new version also enables the configuration of the watchdog timeout via the DT "timeout-sec" property (if enabled via CONFIG_OF_CONTROL). This patch also adds a new flag to the GD flags, to flag that the watchdog is ready to use and adds the pointer to the watchdog device to the GD. This enables us to remove the global "watchdog_dev" variable, which was prone to cause problems because of its potentially very early use in watchdog_reset(), even before the BSS is cleared. Signed-off-by: Stefan Roese <sr(a)denx.de> Cc: Heiko Schocher <hs(a)denx.de> Cc: Tom Rini <trini(a)konsulko.com> Cc: Michal Simek <michal.simek(a)xilinx.com> Cc: "Marek Behún" <marek.behun(a)nic.cz> Cc: Daniel Schwierzeck <daniel.schwierzeck(a)gmail.com> Cc: Maxim Sloyko <maxims(a)google.com> Cc: Erik van Luijk <evanluijk(a)interact.nl> Cc: Ryder Lee <ryder.lee(a)mediatek.com> Cc: Weijie Gao <weijie.gao(a)mediatek.com> Cc: Simon Glass <sjg(a)chromium.org> Cc: "Álvaro Fernández Rojas" <noltari(a)gmail.com> Cc: Philippe Reynes <philippe.reynes(a)softathome.com> Cc: Christophe Leroy <christophe.leroy(a)c-s.fr> --- This patch depends on the following patch: [1] watchdog: Handle SPL build with watchdog disabled https://patchwork.ozlabs.org/patch/1074098/ We have a few boards that have CONFIG_WDT (DM watchdog driver) enabled and CONFIG_WATCHDOG (U-Boot watchdog servicing) disabled. This might lead to a watchdog reboot, if the board does not boot fast enough into some OS (like Linux) which services the watchdog. With this patch now, the watchdog is started on all those boards (if found via the DT) and also serviced as this patch also "implies" CONFIG_WATCHDOG. If this is not desired, then please send a patch to disable CONFIG_WATCHDOG for this board. Here the list of those boards with their maintainers: taurus: Heiko Schocher <hs(a)denx.de> smartweb: Heiko Schocher <hs(a)denx.de> ast2500: Maxim Sloyko <maxims(a)google.com> picosam9g45: Erik van Luijk <evanluijk(a)interact.nl> mt7623n_bpir2: Ryder Lee <ryder.lee(a)mediatek.com> Weijie Gao <weijie.gao(a)mediatek.com> mt7629_rfb: Ryder Lee <ryder.lee(a)mediatek.com> Weijie Gao <weijie.gao(a)mediatek.com> bitmain_antminer_s9: Michal Simek <monstr(a)monstr.eu> sandbox64: Simon Glass <sjg(a)chromium.org> sandbox: Simon Glass <sjg(a)chromium.org> comtrend_ct5361_ram: "Álvaro Fernández Rojas" <noltari(a)gmail.com> netgear_cg3100d_ram: "Álvaro Fernández Rojas" <noltari(a)gmail.com> bcm968380gerg_ram: Philippe Reynes <philippe.reynes(a)softathome.com> bcm963158_ram: Philippe Reynes <philippe.reynes(a)softathome.com> bcm968580xref_ram: Philippe Reynes <philippe.reynes(a)softathome.com> MCR3000: Christophe Leroy <christophe.leroy(a)c-s.fr> Thanks, Stefan v4: - No change v3: - Use already available CONFIG_WATCHDOG_TIMEOUT_MSECS option vs the newly introduced WDT_DEFAULT_TIMEOUT default timeout value (if not provided via DT property). - Guard initr_watchdog by CONFIG_WDT instead of CONFIG_WATCHDOG && CONFIG_WDT as suggested by Michal. This makes it possible to enable and start the U-Boot watchdog without enabling the U-Boot watchdog servicing. - Add imply CONFIG_WATCHDOG to CONFIG_WDT, as this restores the current behaviour to use the U-Boot watchdog servicing feature, if the DM watchdog is enabled (CONFIG_WDT). If this is not desired, CONFIG_WATCHDOG can be disabled in the board defconfig. - Remove CONFIG_WATCHDOG from include/configs/turris_omnia.h v2: - Rename watchdog_start() to initr_watchdog() and move it to board_r.c. This way its only called once, after the DM subsystem has bound all watchdog drivers. This enables the use of the currently implemented logic of using the correct watchdog in U-Boot (via alias etc). arch/mips/mach-mt7620/cpu.c | 36 ---------------- board/CZ.NIC/turris_mox/turris_mox.c | 30 -------------- board/CZ.NIC/turris_omnia/turris_omnia.c | 35 ---------------- .../microblaze-generic/microblaze-generic.c | 40 ------------------ board/xilinx/zynq/board.c | 39 ------------------ board/xilinx/zynqmp/zynqmp.c | 39 ------------------ common/board_r.c | 41 +++++++++++++++++++ drivers/watchdog/Kconfig | 1 + drivers/watchdog/wdt-uclass.c | 26 ++++++++++++ include/asm-generic/global_data.h | 4 ++ include/configs/turris_omnia.h | 5 --- 11 files changed, 72 insertions(+), 224 deletions(-) diff --git a/arch/mips/mach-mt7620/cpu.c b/arch/mips/mach-mt7620/cpu.c index fe74f26a54..fcd0484a6d 100644 --- a/arch/mips/mach-mt7620/cpu.c +++ b/arch/mips/mach-mt7620/cpu.c @@ -69,28 +69,6 @@ int print_cpuinfo(void) return 0; } -#ifdef CONFIG_WATCHDOG -static struct udevice *watchdog_dev __attribute__((section(".data"))) = NULL; - -/* Called by macro WATCHDOG_RESET */ -void watchdog_reset(void) -{ - static ulong next_reset; - ulong now; - - if (!watchdog_dev) - return; - - now = get_timer(0); - - /* Do not reset the watchdog too often */ - if (now > next_reset) { - next_reset = now + 1000; /* reset every 1000ms */ - wdt_reset(watchdog_dev); - } -} -#endif - int arch_misc_init(void) { /* @@ -103,19 +81,5 @@ int arch_misc_init(void) flush_dcache_range(gd->bd->bi_memstart, gd->bd->bi_memstart + gd->ram_size - 1); -#ifdef CONFIG_WATCHDOG - /* Init watchdog */ - if (uclass_get_device_by_seq(UCLASS_WDT, 0, &watchdog_dev)) { - debug("Watchdog: Not found by seq!\n"); - if (uclass_get_device(UCLASS_WDT, 0, &watchdog_dev)) { - puts("Watchdog: Not found!\n"); - return 0; - } - } - - wdt_start(watchdog_dev, 60000, 0); /* 60 seconds */ - printf("Watchdog: Started\n"); -#endif - return 0; } diff --git a/board/CZ.NIC/turris_mox/turris_mox.c b/board/CZ.NIC/turris_mox/turris_mox.c index 96cb9c7e5c..8a4872343b 100644 --- a/board/CZ.NIC/turris_mox/turris_mox.c +++ b/board/CZ.NIC/turris_mox/turris_mox.c @@ -119,41 +119,11 @@ int board_fix_fdt(void *blob) } #endif -#ifdef CONFIG_WDT_ARMADA_37XX -static struct udevice *watchdog_dev __attribute__((section(".data"))) = NULL; - -void watchdog_reset(void) -{ - static ulong next_reset; - ulong now; - - if (!watchdog_dev) - return; - - now = timer_get_us(); - - /* Do not reset the watchdog too often */ - if (now > next_reset) { - wdt_reset(watchdog_dev); - next_reset = now + 100000; - } -} -#endif - int board_init(void) { /* address of boot parameters */ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; -#ifdef CONFIG_WDT_ARMADA_37XX - if (uclass_get_device(UCLASS_WDT, 0, &watchdog_dev)) { - printf("Cannot find Armada 3720 watchdog!\n"); - } else { - printf("Enabling Armada 3720 watchdog (3 minutes timeout).\n"); - wdt_start(watchdog_dev, 180000, 0); - } -#endif - return 0; } diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c index c7f6479a0c..8101cfd88a 100644 --- a/board/CZ.NIC/turris_omnia/turris_omnia.c +++ b/board/CZ.NIC/turris_omnia/turris_omnia.c @@ -364,25 +364,12 @@ static bool disable_mcu_watchdog(void) } #endif -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT_ORION) -static struct udevice *watchdog_dev __attribute__((section(".data"))) = NULL; -#endif - int board_init(void) { /* adress of boot parameters */ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; #ifndef CONFIG_SPL_BUILD -# ifdef CONFIG_WDT_ORION - if (uclass_get_device(UCLASS_WDT, 0, &watchdog_dev)) { - puts("Cannot find Armada 385 watchdog!\n"); - } else { - puts("Enabling Armada 385 watchdog.\n"); - wdt_start(watchdog_dev, (u32) 25000000 * 120, 0); - } -# endif - if (disable_mcu_watchdog()) puts("Disabled MCU startup watchdog.\n"); @@ -392,28 +379,6 @@ int board_init(void) return 0; } -#ifdef CONFIG_WATCHDOG -/* Called by macro WATCHDOG_RESET */ -void watchdog_reset(void) -{ -# if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT_ORION) - static ulong next_reset = 0; - ulong now; - - if (!watchdog_dev) - return; - - now = timer_get_us(); - - /* Do not reset the watchdog too often */ - if (now > next_reset) { - wdt_reset(watchdog_dev); - next_reset = now + 1000; - } -# endif -} -#endif - int board_late_init(void) { #ifndef CONFIG_SPL_BUILD diff --git a/board/xilinx/microblaze-generic/microblaze-generic.c b/board/xilinx/microblaze-generic/microblaze-generic.c index 28c9efa3a2..ba82292e35 100644 --- a/board/xilinx/microblaze-generic/microblaze-generic.c +++ b/board/xilinx/microblaze-generic/microblaze-generic.c @@ -24,10 +24,6 @@ DECLARE_GLOBAL_DATA_PTR; -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT) -static struct udevice *watchdog_dev __attribute__((section(".data"))) = NULL; -#endif /* !CONFIG_SPL_BUILD && CONFIG_WDT */ - ulong ram_base; int dram_init_banksize(void) @@ -43,44 +39,8 @@ int dram_init(void) return 0; }; -#ifdef CONFIG_WDT -/* Called by macro WATCHDOG_RESET */ -void watchdog_reset(void) -{ -#if !defined(CONFIG_SPL_BUILD) - ulong now; - static ulong next_reset; - - if (!watchdog_dev) - return; - - now = timer_get_us(); - - /* Do not reset the watchdog too often */ - if (now > next_reset) { - wdt_reset(watchdog_dev); - next_reset = now + 1000; - } -#endif /* !CONFIG_SPL_BUILD */ -} -#endif /* CONFIG_WDT */ - int board_late_init(void) { -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT) - watchdog_dev = NULL; - - if (uclass_get_device_by_seq(UCLASS_WDT, 0, &watchdog_dev)) { - debug("Watchdog: Not found by seq!\n"); - if (uclass_get_device(UCLASS_WDT, 0, &watchdog_dev)) { - puts("Watchdog: Not found!\n"); - return 0; - } - } - - wdt_start(watchdog_dev, 0, 0); - puts("Watchdog: Started\n"); -#endif /* !CONFIG_SPL_BUILD && CONFIG_WDT */ #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_SYSRESET_MICROBLAZE) int ret; diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c index ea26aad16f..6857f2c0b8 100644 --- a/board/xilinx/zynq/board.c +++ b/board/xilinx/zynq/board.c @@ -18,10 +18,6 @@ DECLARE_GLOBAL_DATA_PTR; -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT) -static struct udevice *watchdog_dev __attribute__((section(".data"))) = NULL; -#endif - #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_BOARD_EARLY_INIT_F) int board_early_init_f(void) { @@ -31,19 +27,6 @@ int board_early_init_f(void) int board_init(void) { -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT) - if (uclass_get_device_by_seq(UCLASS_WDT, 0, &watchdog_dev)) { - debug("Watchdog: Not found by seq!\n"); - if (uclass_get_device(UCLASS_WDT, 0, &watchdog_dev)) { - puts("Watchdog: Not found!\n"); - return 0; - } - } - - wdt_start(watchdog_dev, 0, 0); - puts("Watchdog: Started\n"); -# endif - return 0; } @@ -127,25 +110,3 @@ int dram_init(void) return 0; } #endif - -#if defined(CONFIG_WATCHDOG) -/* Called by macro WATCHDOG_RESET */ -void watchdog_reset(void) -{ -# if !defined(CONFIG_SPL_BUILD) - static ulong next_reset; - ulong now; - - if (!watchdog_dev) - return; - - now = timer_get_us(); - - /* Do not reset the watchdog too often */ - if (now > next_reset) { - wdt_reset(watchdog_dev); - next_reset = now + 1000; - } -# endif -} -#endif diff --git a/board/xilinx/zynqmp/zynqmp.c b/board/xilinx/zynqmp/zynqmp.c index db27247850..1c12891b82 100644 --- a/board/xilinx/zynqmp/zynqmp.c +++ b/board/xilinx/zynqmp/zynqmp.c @@ -24,10 +24,6 @@ DECLARE_GLOBAL_DATA_PTR; -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT) -static struct udevice *watchdog_dev __attribute__((section(".data"))) = NULL; -#endif - #if defined(CONFIG_FPGA) && defined(CONFIG_FPGA_ZYNQMPPL) && \ !defined(CONFIG_SPL_BUILD) static xilinx_desc zynqmppl = XILINX_ZYNQMP_DESC; @@ -340,44 +336,9 @@ int board_init(void) } #endif -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT) - if (uclass_get_device_by_seq(UCLASS_WDT, 0, &watchdog_dev)) { - debug("Watchdog: Not found by seq!\n"); - if (uclass_get_device(UCLASS_WDT, 0, &watchdog_dev)) { - puts("Watchdog: Not found!\n"); - return 0; - } - } - - wdt_start(watchdog_dev, 0, 0); - puts("Watchdog: Started\n"); -#endif - return 0; } -#ifdef CONFIG_WATCHDOG -/* Called by macro WATCHDOG_RESET */ -void watchdog_reset(void) -{ -# if !defined(CONFIG_SPL_BUILD) - static ulong next_reset; - ulong now; - - if (!watchdog_dev) - return; - - now = timer_get_us(); - - /* Do not reset the watchdog too often */ - if (now > next_reset) { - wdt_reset(watchdog_dev); - next_reset = now + 1000; - } -# endif -} -#endif - int board_early_init_r(void) { u32 val; diff --git a/common/board_r.c b/common/board_r.c index 472987d5d5..d457b6715f 100644 --- a/common/board_r.c +++ b/common/board_r.c @@ -48,6 +48,7 @@ #include <linux/compiler.h> #include <linux/err.h> #include <efi_loader.h> +#include <wdt.h> DECLARE_GLOBAL_DATA_PTR; @@ -621,6 +622,43 @@ static int initr_bedbug(void) } #endif +#if defined(CONFIG_WDT) +#ifndef CONFIG_WATCHDOG_TIMEOUT_MSECS +#define CONFIG_WATCHDOG_TIMEOUT_MSECS (60 * 1000) +#endif +#define WATCHDOG_TIMEOUT_SECS (CONFIG_WATCHDOG_TIMEOUT_MSECS / 1000) + +static int initr_watchdog(void) +{ + u32 timeout = WATCHDOG_TIMEOUT_SECS; + + /* + * Init watchdog: This will call the probe function of the + * watchdog driver, enabling the use of the device + */ + if (uclass_get_device_by_seq(UCLASS_WDT, 0, + (struct udevice **)&gd->watchdog_dev)) { + debug("WDT: Not found by seq!\n"); + if (uclass_get_device(UCLASS_WDT, 0, + (struct udevice **)&gd->watchdog_dev)) { + printf("WDT: Not found!\n"); + return 0; + } + } + + if (CONFIG_IS_ENABLED(OF_CONTROL)) { + timeout = dev_read_u32_default(gd->watchdog_dev, "timeout-sec", + WATCHDOG_TIMEOUT_SECS); + } + + wdt_start(gd->watchdog_dev, timeout * 1000, 0); + gd->flags |= GD_FLG_WDT_READY; + printf("WDT: Started (%ds timeout)\n", timeout); + + return 0; +} +#endif + static int run_main_loop(void) { #ifdef CONFIG_SANDBOX @@ -670,6 +708,9 @@ static init_fnc_t init_sequence_r[] = { #ifdef CONFIG_DM initr_dm, #endif +#if defined(CONFIG_WDT) + initr_watchdog, +#endif #if defined(CONFIG_ARM) || defined(CONFIG_NDS32) || defined(CONFIG_RISCV) || \ defined(CONFIG_SANDBOX) board_init, /* Setup chipselects */ diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig index 34e78beb2a..82080d3867 100644 --- a/drivers/watchdog/Kconfig +++ b/drivers/watchdog/Kconfig @@ -51,6 +51,7 @@ config ULP_WATCHDOG config WDT bool "Enable driver model for watchdog timer drivers" depends on DM + imply WATCHDOG help Enable driver model for watchdog timer. At the moment the API is very simple and only supports four operations: diff --git a/drivers/watchdog/wdt-uclass.c b/drivers/watchdog/wdt-uclass.c index 23b7e3360d..bbfac4f0f9 100644 --- a/drivers/watchdog/wdt-uclass.c +++ b/drivers/watchdog/wdt-uclass.c @@ -10,6 +10,8 @@ #include <dm/device-internal.h> #include <dm/lists.h> +DECLARE_GLOBAL_DATA_PTR; + int wdt_start(struct udevice *dev, u64 timeout_ms, ulong flags) { const struct wdt_ops *ops = device_get_ops(dev); @@ -63,6 +65,30 @@ int wdt_expire_now(struct udevice *dev, ulong flags) return ret; } +#if defined(CONFIG_WATCHDOG) +/* + * Called by macro WATCHDOG_RESET. This function be called *very* early, + * so we need to make sure, that the watchdog driver is ready before using + * it in this function. + */ +void watchdog_reset(void) +{ + static ulong next_reset; + ulong now; + + /* Exit if GD is not ready or watchdog is not initialized yet */ + if (!gd || !(gd->flags & GD_FLG_WDT_READY)) + return; + + /* Do not reset the watchdog too often */ + now = get_timer(0); + if (now > next_reset) { + next_reset = now + 1000; /* reset every 1000ms */ + wdt_reset(gd->watchdog_dev); + } +} +#endif + static int wdt_post_bind(struct udevice *dev) { #if defined(CONFIG_NEEDS_MANUAL_RELOC) diff --git a/include/asm-generic/global_data.h b/include/asm-generic/global_data.h index 78dcf40bff..d16f50f677 100644 --- a/include/asm-generic/global_data.h +++ b/include/asm-generic/global_data.h @@ -133,6 +133,9 @@ typedef struct global_data { struct spl_handoff *spl_handoff; # endif #endif +#if defined(CONFIG_WDT) + struct udevice *watchdog_dev; +#endif } gd_t; #endif @@ -161,5 +164,6 @@ typedef struct global_data { #define GD_FLG_ENV_DEFAULT 0x02000 /* Default variable flag */ #define GD_FLG_SPL_EARLY_INIT 0x04000 /* Early SPL init is done */ #define GD_FLG_LOG_READY 0x08000 /* Log system is ready for use */ +#define GD_FLG_WDT_READY 0x10000 /* Watchdog is ready for use */ #endif /* __ASM_GENERIC_GBL_DATA_H */ diff --git a/include/configs/turris_omnia.h b/include/configs/turris_omnia.h index 038f6398eb..78e3cf2ff4 100644 --- a/include/configs/turris_omnia.h +++ b/include/configs/turris_omnia.h @@ -29,11 +29,6 @@ #define CONFIG_SPL_I2C_MUX #define CONFIG_SYS_I2C_MVTWSI -/* Watchdog support */ -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT_ORION) -# define CONFIG_WATCHDOG -#endif - /* SPI NOR flash default params, used by sf commands */ #define CONFIG_SPI_FLASH_SPANSION -- 2.21.0

3 9

[U-Boot] [PATCH 1/4 v5] watchdog: Implement generic watchdog_reset() version
by Stefan Roese 20 Feb '20

20 Feb '20

This patch tries to implement a generic watchdog_reset() function that can be used by all boards that want to service the watchdog device in U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG. Without this approach, new boards or platforms needed to implement a board specific version of this functionality, mostly copy'ing the same code over and over again into their board or platforms code base. With this new generic function, the scattered other functions are now removed to be replaced by the generic one. The new version also enables the configuration of the watchdog timeout via the DT "timeout-sec" property (if enabled via CONFIG_OF_CONTROL). This patch also adds a new flag to the GD flags, to flag that the watchdog is ready to use and adds the pointer to the watchdog device to the GD. This enables us to remove the global "watchdog_dev" variable, which was prone to cause problems because of its potentially very early use in watchdog_reset(), even before the BSS is cleared. Signed-off-by: Stefan Roese <sr(a)denx.de> Cc: Heiko Schocher <hs(a)denx.de> Cc: Tom Rini <trini(a)konsulko.com> Cc: Michal Simek <michal.simek(a)xilinx.com> Cc: "Marek Behún" <marek.behun(a)nic.cz> Cc: Daniel Schwierzeck <daniel.schwierzeck(a)gmail.com> Cc: Maxim Sloyko <maxims(a)google.com> Cc: Erik van Luijk <evanluijk(a)interact.nl> Cc: Ryder Lee <ryder.lee(a)mediatek.com> Cc: Weijie Gao <weijie.gao(a)mediatek.com> Cc: Simon Glass <sjg(a)chromium.org> Cc: "Álvaro Fernández Rojas" <noltari(a)gmail.com> Cc: Philippe Reynes <philippe.reynes(a)softathome.com> Cc: Christophe Leroy <christophe.leroy(a)c-s.fr> Cc: Chris Packham <chris.packham(a)alliedtelesis.co.nz> Reviewed-by: Michal Simek <michal.simek(a)xilinx.com> Tested-by: Michal Simek <michal.simek(a)xilinx.com> (on zcu100) --- We have a few boards that have CONFIG_WDT (DM watchdog driver) enabled and CONFIG_WATCHDOG (U-Boot watchdog servicing) disabled. This might lead to a watchdog reboot, if the board does not boot fast enough into some OS (like Linux) which services the watchdog. With this patch now, the watchdog is started on all those boards (if found via the DT) and also serviced as this patch also "implies" CONFIG_WATCHDOG. If this is not desired, then please send a patch to disable CONFIG_WATCHDOG for this board. Here the list of those boards with their maintainers: taurus: Heiko Schocher <hs(a)denx.de> smartweb: Heiko Schocher <hs(a)denx.de> ast2500: Maxim Sloyko <maxims(a)google.com> picosam9g45: Erik van Luijk <evanluijk(a)interact.nl> mt7623n_bpir2: Ryder Lee <ryder.lee(a)mediatek.com> Weijie Gao <weijie.gao(a)mediatek.com> mt7629_rfb: Ryder Lee <ryder.lee(a)mediatek.com> Weijie Gao <weijie.gao(a)mediatek.com> bitmain_antminer_s9: Michal Simek <monstr(a)monstr.eu> sandbox64: Simon Glass <sjg(a)chromium.org> sandbox: Simon Glass <sjg(a)chromium.org> comtrend_ct5361_ram: "Álvaro Fernández Rojas" <noltari(a)gmail.com> netgear_cg3100d_ram: "Álvaro Fernández Rojas" <noltari(a)gmail.com> bcm968380gerg_ram: Philippe Reynes <philippe.reynes(a)softathome.com> bcm963158_ram: Philippe Reynes <philippe.reynes(a)softathome.com> bcm968580xref_ram: Philippe Reynes <philippe.reynes(a)softathome.com> MCR3000: Christophe Leroy <christophe.leroy(a)c-s.fr> Thanks, Stefan v5: - Remove board specific x530 watchdog support and implement this in this generic apprioach as well. For this, we need to support the watchdog in SPL now. Move the watchdog init function initr_watchdog() into wdt.h to not duplicate this code. v4: - No change v3: - Use already available CONFIG_WATCHDOG_TIMEOUT_MSECS option vs the newly introduced WDT_DEFAULT_TIMEOUT default timeout value (if not provided via DT property). - Guard initr_watchdog by CONFIG_WDT instead of CONFIG_WATCHDOG && CONFIG_WDT as suggested by Michal. This makes it possible to enable and start the U-Boot watchdog without enabling the U-Boot watchdog servicing. - Add imply CONFIG_WATCHDOG to CONFIG_WDT, as this restores the current behaviour to use the U-Boot watchdog servicing feature, if the DM watchdog is enabled (CONFIG_WDT). If this is not desired, CONFIG_WATCHDOG can be disabled in the board defconfig. - Remove CONFIG_WATCHDOG from include/configs/turris_omnia.h v2: - Rename watchdog_start() to initr_watchdog() and move it to board_r.c. This way its only called once, after the DM subsystem has bound all watchdog drivers. This enables the use of the currently implemented logic of using the correct watchdog in U-Boot (via alias etc). arch/mips/mach-mt7620/cpu.c | 36 ---------------- board/CZ.NIC/turris_mox/turris_mox.c | 30 -------------- board/CZ.NIC/turris_omnia/turris_omnia.c | 35 ---------------- board/alliedtelesis/x530/x530.c | 36 +--------------- .../microblaze-generic/microblaze-generic.c | 40 ------------------ board/xilinx/zynq/board.c | 39 ------------------ board/xilinx/zynqmp/zynqmp.c | 39 ------------------ common/board_r.c | 4 ++ common/spl/spl.c | 5 +++ drivers/watchdog/Kconfig | 1 + drivers/watchdog/wdt-uclass.c | 26 ++++++++++++ include/asm-generic/global_data.h | 4 ++ include/configs/turris_omnia.h | 5 --- include/wdt.h | 41 +++++++++++++++++++ 14 files changed, 82 insertions(+), 259 deletions(-) diff --git a/arch/mips/mach-mt7620/cpu.c b/arch/mips/mach-mt7620/cpu.c index fe74f26a54..fcd0484a6d 100644 --- a/arch/mips/mach-mt7620/cpu.c +++ b/arch/mips/mach-mt7620/cpu.c @@ -69,28 +69,6 @@ int print_cpuinfo(void) return 0; } -#ifdef CONFIG_WATCHDOG -static struct udevice *watchdog_dev __attribute__((section(".data"))) = NULL; - -/* Called by macro WATCHDOG_RESET */ -void watchdog_reset(void) -{ - static ulong next_reset; - ulong now; - - if (!watchdog_dev) - return; - - now = get_timer(0); - - /* Do not reset the watchdog too often */ - if (now > next_reset) { - next_reset = now + 1000; /* reset every 1000ms */ - wdt_reset(watchdog_dev); - } -} -#endif - int arch_misc_init(void) { /* @@ -103,19 +81,5 @@ int arch_misc_init(void) flush_dcache_range(gd->bd->bi_memstart, gd->bd->bi_memstart + gd->ram_size - 1); -#ifdef CONFIG_WATCHDOG - /* Init watchdog */ - if (uclass_get_device_by_seq(UCLASS_WDT, 0, &watchdog_dev)) { - debug("Watchdog: Not found by seq!\n"); - if (uclass_get_device(UCLASS_WDT, 0, &watchdog_dev)) { - puts("Watchdog: Not found!\n"); - return 0; - } - } - - wdt_start(watchdog_dev, 60000, 0); /* 60 seconds */ - printf("Watchdog: Started\n"); -#endif - return 0; } diff --git a/board/CZ.NIC/turris_mox/turris_mox.c b/board/CZ.NIC/turris_mox/turris_mox.c index 96cb9c7e5c..8a4872343b 100644 --- a/board/CZ.NIC/turris_mox/turris_mox.c +++ b/board/CZ.NIC/turris_mox/turris_mox.c @@ -119,41 +119,11 @@ int board_fix_fdt(void *blob) } #endif -#ifdef CONFIG_WDT_ARMADA_37XX -static struct udevice *watchdog_dev __attribute__((section(".data"))) = NULL; - -void watchdog_reset(void) -{ - static ulong next_reset; - ulong now; - - if (!watchdog_dev) - return; - - now = timer_get_us(); - - /* Do not reset the watchdog too often */ - if (now > next_reset) { - wdt_reset(watchdog_dev); - next_reset = now + 100000; - } -} -#endif - int board_init(void) { /* address of boot parameters */ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; -#ifdef CONFIG_WDT_ARMADA_37XX - if (uclass_get_device(UCLASS_WDT, 0, &watchdog_dev)) { - printf("Cannot find Armada 3720 watchdog!\n"); - } else { - printf("Enabling Armada 3720 watchdog (3 minutes timeout).\n"); - wdt_start(watchdog_dev, 180000, 0); - } -#endif - return 0; } diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c index 0287f23283..4c08f810a2 100644 --- a/board/CZ.NIC/turris_omnia/turris_omnia.c +++ b/board/CZ.NIC/turris_omnia/turris_omnia.c @@ -364,25 +364,12 @@ static bool disable_mcu_watchdog(void) } #endif -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT_ORION) -static struct udevice *watchdog_dev __attribute__((section(".data"))) = NULL; -#endif - int board_init(void) { /* adress of boot parameters */ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; #ifndef CONFIG_SPL_BUILD -# ifdef CONFIG_WDT_ORION - if (uclass_get_device(UCLASS_WDT, 0, &watchdog_dev)) { - puts("Cannot find Armada 385 watchdog!\n"); - } else { - puts("Enabling Armada 385 watchdog.\n"); - wdt_start(watchdog_dev, 120000, 0); - } -# endif - if (disable_mcu_watchdog()) puts("Disabled MCU startup watchdog.\n"); @@ -392,28 +379,6 @@ int board_init(void) return 0; } -#ifdef CONFIG_WATCHDOG -/* Called by macro WATCHDOG_RESET */ -void watchdog_reset(void) -{ -# if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT_ORION) - static ulong next_reset = 0; - ulong now; - - if (!watchdog_dev) - return; - - now = timer_get_us(); - - /* Do not reset the watchdog too often */ - if (now > next_reset) { - wdt_reset(watchdog_dev); - next_reset = now + 1000; - } -# endif -} -#endif - int board_late_init(void) { #ifndef CONFIG_SPL_BUILD diff --git a/board/alliedtelesis/x530/x530.c b/board/alliedtelesis/x530/x530.c index 6934fd8017..97dbed79dd 100644 --- a/board/alliedtelesis/x530/x530.c +++ b/board/alliedtelesis/x530/x530.c @@ -25,10 +25,6 @@ DECLARE_GLOBAL_DATA_PTR; #define CONFIG_NVS_LOCATION 0xf4800000 #define CONFIG_NVS_SIZE (512 << 10) -#ifdef CONFIG_WATCHDOG -static struct udevice *watchdog_dev; -#endif - static struct serdes_map board_serdes_map[] = { {PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}, {DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}, @@ -80,10 +76,6 @@ struct mv_ddr_topology_map *mv_ddr_topology_map_get(void) int board_early_init_f(void) { -#ifdef CONFIG_WATCHDOG - watchdog_dev = NULL; -#endif - /* Configure MPP */ writel(0x00001111, MVEBU_MPP_BASE + 0x00); writel(0x00000000, MVEBU_MPP_BASE + 0x04); @@ -99,13 +91,6 @@ int board_early_init_f(void) void spl_board_init(void) { -#ifdef CONFIG_WATCHDOG - int ret; - - ret = uclass_get_device(UCLASS_WDT, 0, &watchdog_dev); - if (!ret) - wdt_start(watchdog_dev, 120000, 0); -#endif } int board_init(void) @@ -128,29 +113,10 @@ int board_init(void) void arch_preboot_os(void) { #ifdef CONFIG_WATCHDOG - wdt_stop(watchdog_dev); + wdt_stop(gd->watchdog_dev); #endif } -#ifdef CONFIG_WATCHDOG -void watchdog_reset(void) -{ - static ulong next_reset = 0; - ulong now; - - if (!watchdog_dev) - return; - - now = timer_get_us(); - - /* Do not reset the watchdog too often */ - if (now > next_reset) { - wdt_reset(watchdog_dev); - next_reset = now + 1000; - } -} -#endif - static int led_7seg_init(unsigned int segments) { int node; diff --git a/board/xilinx/microblaze-generic/microblaze-generic.c b/board/xilinx/microblaze-generic/microblaze-generic.c index 28c9efa3a2..ba82292e35 100644 --- a/board/xilinx/microblaze-generic/microblaze-generic.c +++ b/board/xilinx/microblaze-generic/microblaze-generic.c @@ -24,10 +24,6 @@ DECLARE_GLOBAL_DATA_PTR; -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT) -static struct udevice *watchdog_dev __attribute__((section(".data"))) = NULL; -#endif /* !CONFIG_SPL_BUILD && CONFIG_WDT */ - ulong ram_base; int dram_init_banksize(void) @@ -43,44 +39,8 @@ int dram_init(void) return 0; }; -#ifdef CONFIG_WDT -/* Called by macro WATCHDOG_RESET */ -void watchdog_reset(void) -{ -#if !defined(CONFIG_SPL_BUILD) - ulong now; - static ulong next_reset; - - if (!watchdog_dev) - return; - - now = timer_get_us(); - - /* Do not reset the watchdog too often */ - if (now > next_reset) { - wdt_reset(watchdog_dev); - next_reset = now + 1000; - } -#endif /* !CONFIG_SPL_BUILD */ -} -#endif /* CONFIG_WDT */ - int board_late_init(void) { -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT) - watchdog_dev = NULL; - - if (uclass_get_device_by_seq(UCLASS_WDT, 0, &watchdog_dev)) { - debug("Watchdog: Not found by seq!\n"); - if (uclass_get_device(UCLASS_WDT, 0, &watchdog_dev)) { - puts("Watchdog: Not found!\n"); - return 0; - } - } - - wdt_start(watchdog_dev, 0, 0); - puts("Watchdog: Started\n"); -#endif /* !CONFIG_SPL_BUILD && CONFIG_WDT */ #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_SYSRESET_MICROBLAZE) int ret; diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c index ea26aad16f..6857f2c0b8 100644 --- a/board/xilinx/zynq/board.c +++ b/board/xilinx/zynq/board.c @@ -18,10 +18,6 @@ DECLARE_GLOBAL_DATA_PTR; -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT) -static struct udevice *watchdog_dev __attribute__((section(".data"))) = NULL; -#endif - #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_BOARD_EARLY_INIT_F) int board_early_init_f(void) { @@ -31,19 +27,6 @@ int board_early_init_f(void) int board_init(void) { -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT) - if (uclass_get_device_by_seq(UCLASS_WDT, 0, &watchdog_dev)) { - debug("Watchdog: Not found by seq!\n"); - if (uclass_get_device(UCLASS_WDT, 0, &watchdog_dev)) { - puts("Watchdog: Not found!\n"); - return 0; - } - } - - wdt_start(watchdog_dev, 0, 0); - puts("Watchdog: Started\n"); -# endif - return 0; } @@ -127,25 +110,3 @@ int dram_init(void) return 0; } #endif - -#if defined(CONFIG_WATCHDOG) -/* Called by macro WATCHDOG_RESET */ -void watchdog_reset(void) -{ -# if !defined(CONFIG_SPL_BUILD) - static ulong next_reset; - ulong now; - - if (!watchdog_dev) - return; - - now = timer_get_us(); - - /* Do not reset the watchdog too often */ - if (now > next_reset) { - wdt_reset(watchdog_dev); - next_reset = now + 1000; - } -# endif -} -#endif diff --git a/board/xilinx/zynqmp/zynqmp.c b/board/xilinx/zynqmp/zynqmp.c index 5189925beb..c840e92d9c 100644 --- a/board/xilinx/zynqmp/zynqmp.c +++ b/board/xilinx/zynqmp/zynqmp.c @@ -24,10 +24,6 @@ DECLARE_GLOBAL_DATA_PTR; -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT) -static struct udevice *watchdog_dev __attribute__((section(".data"))) = NULL; -#endif - #if defined(CONFIG_FPGA) && defined(CONFIG_FPGA_ZYNQMPPL) && \ !defined(CONFIG_SPL_BUILD) static xilinx_desc zynqmppl = XILINX_ZYNQMP_DESC; @@ -344,44 +340,9 @@ int board_init(void) } #endif -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT) - if (uclass_get_device_by_seq(UCLASS_WDT, 0, &watchdog_dev)) { - debug("Watchdog: Not found by seq!\n"); - if (uclass_get_device(UCLASS_WDT, 0, &watchdog_dev)) { - puts("Watchdog: Not found!\n"); - return 0; - } - } - - wdt_start(watchdog_dev, 0, 0); - puts("Watchdog: Started\n"); -#endif - return 0; } -#ifdef CONFIG_WATCHDOG -/* Called by macro WATCHDOG_RESET */ -void watchdog_reset(void) -{ -# if !defined(CONFIG_SPL_BUILD) - static ulong next_reset; - ulong now; - - if (!watchdog_dev) - return; - - now = timer_get_us(); - - /* Do not reset the watchdog too often */ - if (now > next_reset) { - wdt_reset(watchdog_dev); - next_reset = now + 1000; - } -# endif -} -#endif - int board_early_init_r(void) { u32 val; diff --git a/common/board_r.c b/common/board_r.c index 1ad44bbe3f..150e8cd424 100644 --- a/common/board_r.c +++ b/common/board_r.c @@ -48,6 +48,7 @@ #include <linux/compiler.h> #include <linux/err.h> #include <efi_loader.h> +#include <wdt.h> DECLARE_GLOBAL_DATA_PTR; @@ -677,6 +678,9 @@ static init_fnc_t init_sequence_r[] = { #ifdef CONFIG_DM initr_dm, #endif +#if defined(CONFIG_WDT) + initr_watchdog, +#endif #if defined(CONFIG_ARM) || defined(CONFIG_NDS32) || defined(CONFIG_RISCV) || \ defined(CONFIG_SANDBOX) board_init, /* Setup chipselects */ diff --git a/common/spl/spl.c b/common/spl/spl.c index 88d4b8a9bf..0a6a47c202 100644 --- a/common/spl/spl.c +++ b/common/spl/spl.c @@ -22,6 +22,7 @@ #include <linux/compiler.h> #include <fdt_support.h> #include <bootcount.h> +#include <wdt.h> DECLARE_GLOBAL_DATA_PTR; @@ -600,6 +601,10 @@ void board_init_r(gd_t *dummy1, ulong dummy2) spl_board_init(); #endif +#if defined(CONFIG_SPL_WATCHDOG_SUPPORT) && defined(CONFIG_WDT) + initr_watchdog(); +#endif + if (IS_ENABLED(CONFIG_SPL_OS_BOOT) || CONFIG_IS_ENABLED(HANDOFF)) dram_init_banksize(); diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig index 9d7f503b69..aa8e725573 100644 --- a/drivers/watchdog/Kconfig +++ b/drivers/watchdog/Kconfig @@ -51,6 +51,7 @@ config ULP_WATCHDOG config WDT bool "Enable driver model for watchdog timer drivers" depends on DM + imply WATCHDOG help Enable driver model for watchdog timer. At the moment the API is very simple and only supports four operations: diff --git a/drivers/watchdog/wdt-uclass.c b/drivers/watchdog/wdt-uclass.c index 23b7e3360d..bbfac4f0f9 100644 --- a/drivers/watchdog/wdt-uclass.c +++ b/drivers/watchdog/wdt-uclass.c @@ -10,6 +10,8 @@ #include <dm/device-internal.h> #include <dm/lists.h> +DECLARE_GLOBAL_DATA_PTR; + int wdt_start(struct udevice *dev, u64 timeout_ms, ulong flags) { const struct wdt_ops *ops = device_get_ops(dev); @@ -63,6 +65,30 @@ int wdt_expire_now(struct udevice *dev, ulong flags) return ret; } +#if defined(CONFIG_WATCHDOG) +/* + * Called by macro WATCHDOG_RESET. This function be called *very* early, + * so we need to make sure, that the watchdog driver is ready before using + * it in this function. + */ +void watchdog_reset(void) +{ + static ulong next_reset; + ulong now; + + /* Exit if GD is not ready or watchdog is not initialized yet */ + if (!gd || !(gd->flags & GD_FLG_WDT_READY)) + return; + + /* Do not reset the watchdog too often */ + now = get_timer(0); + if (now > next_reset) { + next_reset = now + 1000; /* reset every 1000ms */ + wdt_reset(gd->watchdog_dev); + } +} +#endif + static int wdt_post_bind(struct udevice *dev) { #if defined(CONFIG_NEEDS_MANUAL_RELOC) diff --git a/include/asm-generic/global_data.h b/include/asm-generic/global_data.h index 78dcf40bff..d16f50f677 100644 --- a/include/asm-generic/global_data.h +++ b/include/asm-generic/global_data.h @@ -133,6 +133,9 @@ typedef struct global_data { struct spl_handoff *spl_handoff; # endif #endif +#if defined(CONFIG_WDT) + struct udevice *watchdog_dev; +#endif } gd_t; #endif @@ -161,5 +164,6 @@ typedef struct global_data { #define GD_FLG_ENV_DEFAULT 0x02000 /* Default variable flag */ #define GD_FLG_SPL_EARLY_INIT 0x04000 /* Early SPL init is done */ #define GD_FLG_LOG_READY 0x08000 /* Log system is ready for use */ +#define GD_FLG_WDT_READY 0x10000 /* Watchdog is ready for use */ #endif /* __ASM_GENERIC_GBL_DATA_H */ diff --git a/include/configs/turris_omnia.h b/include/configs/turris_omnia.h index c7805cf36b..0e65a12345 100644 --- a/include/configs/turris_omnia.h +++ b/include/configs/turris_omnia.h @@ -29,11 +29,6 @@ #define CONFIG_SPL_I2C_MUX #define CONFIG_SYS_I2C_MVTWSI -/* Watchdog support */ -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_WDT_ORION) -# define CONFIG_WATCHDOG -#endif - /* * SDIO/MMC Card Configuration */ diff --git a/include/wdt.h b/include/wdt.h index e9a7c5355a..aa77d3e9b4 100644 --- a/include/wdt.h +++ b/include/wdt.h @@ -6,6 +6,9 @@ #ifndef _WDT_H_ #define _WDT_H_ +#include <dm.h> +#include <dm/read.h> + /* * Implement a simple watchdog uclass. Watchdog is basically a timer that * is used to detect or recover from malfunction. During normal operation @@ -103,4 +106,42 @@ struct wdt_ops { int (*expire_now)(struct udevice *dev, ulong flags); }; +#if defined(CONFIG_WDT) +#ifndef CONFIG_WATCHDOG_TIMEOUT_MSECS +#define CONFIG_WATCHDOG_TIMEOUT_MSECS (60 * 1000) +#endif +#define WATCHDOG_TIMEOUT_SECS (CONFIG_WATCHDOG_TIMEOUT_MSECS / 1000) + +static inline int initr_watchdog(void) +{ + u32 timeout = WATCHDOG_TIMEOUT_SECS; + + /* + * Init watchdog: This will call the probe function of the + * watchdog driver, enabling the use of the device + */ + if (uclass_get_device_by_seq(UCLASS_WDT, 0, + (struct udevice **)&gd->watchdog_dev)) { + debug("WDT: Not found by seq!\n"); + if (uclass_get_device(UCLASS_WDT, 0, + (struct udevice **)&gd->watchdog_dev)) { + printf("WDT: Not found!\n"); + return 0; + } + } + + if (CONFIG_IS_ENABLED(OF_CONTROL)) { + timeout = dev_read_u32_default(gd->watchdog_dev, "timeout-sec", + WATCHDOG_TIMEOUT_SECS); + } + + wdt_start(gd->watchdog_dev, timeout * 1000, 0); + gd->flags |= GD_FLG_WDT_READY; + printf("WDT: Started with%s servicing (%ds timeout)\n", + IS_ENABLED(CONFIG_WATCHDOG) ? "" : "out", timeout); + + return 0; +} +#endif + #endif /* _WDT_H_ */ -- 2.21.0

6 23

[U-Boot] [RFC] cmd: add bootslot command to select/boot slot based on boot counts
by Martin Hundebøll 16 Feb '20

16 Feb '20

The existing bootcount feature is targeted systems with a primary, and a rescue boot setup, where the number of boot tries to the primary boot is tracked. If the number exceeds the limit, the alternative/rescue is booted. This patch adds support for a more sophisticated setup, where more than two boot slots can exist, and the order of slots can be configured. The 'bootcommand' command reads the configured slots (and their priority/order) from a configured environment variable ("bootslots" by default). For each conifgured slot, a remaining boot count is maintained in an evnironment variable ("bootcount_<slot>" by default). If the first boot slot has positive boot count, it is booted using the slot specific boot command ("bootcmd_<slot>" by default). Otherwise the next slot is checked. An example environment when using the bootslot command with two slots ("a" and "b"): bootslots=a b bootcount_a=3 bootcount_b=3 bootcmd_a=setenv bootargs $bootargs root=/dev/mmcblk0p1; booti $loadaddr bootcmd_b=setenv bootargs $bootargs root=/dev/mmcblk0p2; booti $loadaddr Once linux is booted, it resets the bootcount variable for the booted slot using "fw_setenv": > fw_setenv bootcount_a 3 When the non-booted slot is updated, the order is updated by setting the bootslots variable with "fw_setenv": > fw_setenv bootslots=b a Signed-off-by: Martin Hundebøll <martin(a)geanix.com> --- cmd/Kconfig | 42 +++++++++ cmd/Makefile | 1 + cmd/bootslot.c | 225 +++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 268 insertions(+) create mode 100644 cmd/bootslot.c diff --git a/cmd/Kconfig b/cmd/Kconfig index aec209006d..3919606e74 100644 --- a/cmd/Kconfig +++ b/cmd/Kconfig @@ -1277,6 +1277,48 @@ config CMD_BOOTCOUNT Enable the bootcount command, which allows interrogation and reset of the bootcounter. +config CMD_BOOTSLOT + bool "Enable support for multiple boot slots" + help + Parses an ordered list of configured boot slot names (e.g. "a b") + and selects a corresponding boot command based on the current + boot counter for each slot. + +config CMD_BOOTSLOT_ENV_SLOTS + string "Environment variable to read bootslots from" + depends on CMD_BOOTSLOT + default "bootslots" + help + Configures the environment variable to read out when looking for a + list of available boot sloots. + +config CMD_BOOTSLOT_ENV_COUNT + string "Environment variable format string to read/write slot boot count from/to" + depends on CMD_BOOTSLOT + default "bootcount_%s" + help + Configures the prefix to use when reading the boot count for a + specific slot. The prefix is concatenated with the slot name, so + that the boot count for slot "a" is read and saved to "<prefix>a". + +config CMD_BOOTSLOT_ENV_CMD + string "Environment variable format string to read slot boot command from" + depends on CMD_BOOTSLOT + default "bootcmd_%s" + help + Configures the prefix to use when reading the boot command for + specific slot. The prefix is concatenated with the slot name, so + that the boot command for slot "a" is read from "<prefix>a". + +config CMD_BOOTSLOT_DEFAULT_COUNT + int "Default boot count for each configured slot" + depends on CMD_BOOTSLOT + default 3 + help + The default number of times a slot is tried before proceeding to the + slot. The default is used when a slot has no count yet, or when it + is reset with the "bootslot reset" command. + config CMD_BSP bool "Enable board-specific commands" help diff --git a/cmd/Makefile b/cmd/Makefile index 323f1fd2c7..68c8e50c91 100644 --- a/cmd/Makefile +++ b/cmd/Makefile @@ -26,6 +26,7 @@ obj-$(CONFIG_CMD_BOOTCOUNT) += bootcount.o obj-$(CONFIG_CMD_BOOTEFI) += bootefi.o obj-$(CONFIG_CMD_BOOTMENU) += bootmenu.o obj-$(CONFIG_CMD_BOOTSTAGE) += bootstage.o +obj-$(CONFIG_CMD_BOOTSLOT) += bootslot.o obj-$(CONFIG_CMD_BOOTZ) += bootz.o obj-$(CONFIG_CMD_BOOTI) += booti.o obj-$(CONFIG_CMD_BTRFS) += btrfs.o diff --git a/cmd/bootslot.c b/cmd/bootslot.c new file mode 100644 index 0000000000..03897b1f60 --- /dev/null +++ b/cmd/bootslot.c @@ -0,0 +1,225 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (c) 2018, Geanix, All rights reserved. + */ + +#include <common.h> +#include <environment.h> +#include <stdlib.h> +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/compat.h> +#include <vsprintf.h> + +static char *bootslot_envname(const char *fmt, const char *slot) +{ + int len = strlen(fmt) + strlen(slot); + char *envname = malloc(len + 1); + + sprintf(envname, fmt, slot); + + return envname; +} + +static unsigned long bootslot_get_count(const char *slot) +{ + char *envname; + unsigned long count; + + envname = bootslot_envname(CONFIG_CMD_BOOTSLOT_ENV_COUNT, slot); + count = env_get_ulong(envname, 10, CONFIG_CMD_BOOTSLOT_DEFAULT_COUNT); + free(envname); + + return count; +} + +static void bootslot_set_count(const char *slot, unsigned long count) +{ + char *envname; + + envname = bootslot_envname(CONFIG_CMD_BOOTSLOT_ENV_COUNT, slot); + env_set_ulong(envname, count); + free(envname); +} + +static const char *bootslot_get_cmd(const char *slot) +{ + char *envname; + char *cmd; + + envname = bootslot_envname(CONFIG_CMD_BOOTSLOT_ENV_CMD, slot); + cmd = env_get(envname); + free(envname); + + return cmd; +} + +static char *bootslot_get_slots(int argc, char * const argv[]) +{ + char *slots = NULL; + int len = 1; /* make room for terminating \0 */ + int i; + + /* read boot slots from environment if no args are given, or + * duplicate the argument if a single argument is given */ + if (argc == 1) + return strdup(env_get(CONFIG_CMD_BOOTSLOT_ENV_SLOTS)); + else if (argc == 2) + return strdup(argv[1]); + + /* compute the string length of the list of slots */ + for (i = 1; i < argc; i++) + len += strlen(argv[i]) + 1; /* add room for space separator */ + + /* allocate the string buffer and copy each slot argument to it */ + slots = kzalloc(len, 0); + strcpy(slots, argv[1]); + + for (i = 2; i < argc; i++) { + strcat(slots, " "); + strcat(slots, argv[i]); + } + + return slots; +} + +static int do_bootslot_list(cmd_tbl_t *cmdtp, int flag, int argc, + char * const argv[]) +{ + char *mem = bootslot_get_slots(argc, argv); + char *slots = mem; + char *slot; + + if (slots == NULL) + return CMD_RET_USAGE; + + printf("slot\tcount\tbootcmd\n"); + while ((slot = strsep(&slots, " ")) != NULL) { + unsigned long count; + const char *bootcmd; + + if (strlen(slot) == 0) + continue; + + count = bootslot_get_count(slot); + bootcmd = bootslot_get_cmd(slot); + + if (bootcmd) + printf("%s\t%lu\t%s\n", slot, count, bootcmd); + else + printf("%s\t%lu\t<not defined>\n", slot, count); + } + + free(mem); + + return CMD_RET_SUCCESS; +} + +static int do_bootslot_reset(cmd_tbl_t *cmdtp, int flag, int argc, + char * const argv[]) +{ + char *mem = bootslot_get_slots(argc, argv); + char *slots = mem; + char *slot; + + if (slots == NULL) + return CMD_RET_USAGE; + + while ((slot = strsep(&slots, " ")) != NULL) { + if (strlen(slot) == 0) + continue; + bootslot_set_count(slot, CONFIG_CMD_BOOTSLOT_DEFAULT_COUNT); + } + + free(mem); + + return CMD_RET_SUCCESS; +} + +static int do_bootslot_boot(cmd_tbl_t *cmdtp, int flag, int argc, + char * const argv[]) +{ + char *mem = bootslot_get_slots(argc, argv); + char *slots = mem; + char *slot; + bool found_valid = false; + + if (slots == NULL) + return CMD_RET_USAGE; + + while ((slot = strsep(&slots, " ")) != NULL) { + const char *bootcmd; + unsigned long count; + + if (strlen(slot) == 0) + continue; + + count = bootslot_get_count(slot); + if (count == 0) { + printf("slot %s bootcount is zero; trying next...\n", + slot); + continue; + } + + bootcmd = bootslot_get_cmd(slot); + if (bootcmd == NULL) { + printf("slot %s bootcmd not found; trying next...\n", + slot); + continue; + } + + printf("slot %s has %lu boot tries remaining; booting...\n", + slot, count); + found_valid = true; + bootslot_set_count(slot, --count); + env_save(); + run_command_list(bootcmd, -1, CMD_FLAG_ENV); + break; + } + + free(mem); + + if (found_valid == false) { + printf("no valid bootslot found; resetting counters\n"); + run_command("bootslot reset", 0); + return CMD_RET_FAILURE; + } + + return CMD_RET_SUCCESS; +} + +static cmd_tbl_t cmd_bootslot_sub[] = { + U_BOOT_CMD_MKENT(boot, INT_MAX, 0, do_bootslot_boot, "", ""), + U_BOOT_CMD_MKENT(list, INT_MAX, 1, do_bootslot_list, "", ""), + U_BOOT_CMD_MKENT(reset, INT_MAX, 1, do_bootslot_reset, "", ""), +}; + +/* + * Process a bootslots sub-command + */ +static int do_bootslot(cmd_tbl_t *cmdtp, int flag, int argc, + char * const argv[]) +{ + cmd_tbl_t *c; + + /* Strip off leading 'bootslot' command argument */ + argc--; + argv++; + + c = find_cmd_tbl(argv[0], cmd_bootslot_sub, + ARRAY_SIZE(cmd_bootslot_sub)); + + if (c) + return c->cmd(cmdtp, flag, argc, argv); + else + return CMD_RET_USAGE; +} + + +U_BOOT_CMD(bootslot, INT_MAX, 1, do_bootslot, + "Bootslot command", + " - select and boot slot based on counters\n" + "boot [<slot>] - Boot the passed or first valid slot in $bootslots\n" + "list [<slot>] - List remaining boot tries for passed or all slots in $bootslots\n" + "reset [<slot>] - Reset remaining boot tries for all or passed slot\n" +); -- 2.18.0

4 5

[U-Boot] [PATCH] board: ax25-ae350: Print board information.
by Andes 06 Feb '20

06 Feb '20

From: Rick Chen <rick(a)andestech.com> Add to print board and bit information message. Signed-off-by: Rick Chen <rick(a)andestech.com> Cc: Greentime Hu <greentime(a)andestech.com> --- board/AndesTech/ax25-ae350/ax25-ae350.c | 1 + 1 file changed, 1 insertion(+) diff --git a/board/AndesTech/ax25-ae350/ax25-ae350.c b/board/AndesTech/ax25-ae350/ax25-ae350.c index 5f4ca0f..61ca10b 100644 --- a/board/AndesTech/ax25-ae350/ax25-ae350.c +++ b/board/AndesTech/ax25-ae350/ax25-ae350.c @@ -20,6 +20,7 @@ DECLARE_GLOBAL_DATA_PTR; int board_init(void) { + printf("Board: %s (%d)\n" , CONFIG_SYS_BOARD, __riscv_xlen); gd->bd->bi_boot_params = PHYS_SDRAM_0 + 0x400; return 0; -- 2.7.4

3 3

[U-Boot] [PATCH v3] riscv: add Kconfig entries for the F and D ISA extensions support
by Eric Lin 05 Feb '20

05 Feb '20

This patch adds Kconfig entries for the F (Single-Precision) and D (Double-Precision) floating point instruction-set extensions. Signed-off-by: Eric Lin <tesheng(a)andestech.com> --- Changes for v2: - Grammatical correction in commit message "adds" - Fixed the config name to indicate both F and D Changes for v3: - Separate the config name for ISA_F and ISA_D arch/riscv/Kconfig | 14 ++++++++++++++ arch/riscv/Makefile | 16 ++++++++++++---- 2 files changed, 26 insertions(+), 4 deletions(-) diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig index 362f3cdc65..7a2463ffe2 100644 --- a/arch/riscv/Kconfig +++ b/arch/riscv/Kconfig @@ -91,6 +91,20 @@ config RISCV_ISA_C when building U-Boot, which results in compressed instructions in the U-Boot binary. +config RISCV_ISA_F + bool "Emit single-precision floating-point instructions" + help + Adds "F" to the ISA subsets that the toolchain is allowed to emit + when building U-Boot, which results in single-precision instructions + in the U-Boot binary. + +config RISCV_ISA_D + bool "Emit double-precision floating-point instructions" + help + Adds "D" to the ISA subsets that the toolchain is allowed to emit + when building U-Boot, which results in double-precision instructions + in the U-Boot binary. + config RISCV_ISA_A def_bool y diff --git a/arch/riscv/Makefile b/arch/riscv/Makefile index 0b80eb8d86..f834d11720 100644 --- a/arch/riscv/Makefile +++ b/arch/riscv/Makefile @@ -5,15 +5,23 @@ ifeq ($(CONFIG_ARCH_RV64I),y) ARCH_BASE = rv64im - ABI = lp64 + ABI := lp64 endif ifeq ($(CONFIG_ARCH_RV32I),y) ARCH_BASE = rv32im - ABI = ilp32 + ABI := ilp32 endif ifeq ($(CONFIG_RISCV_ISA_A),y) ARCH_A = a endif +ifeq ($(CONFIG_RISCV_ISA_F),y) + ARCH_F = f + ABI := $(ABI)f +endif +ifeq ($(CONFIG_RISCV_ISA_D),y) + ARCH_D = fd + ABI := $(ABI)d +endif ifeq ($(CONFIG_RISCV_ISA_C),y) ARCH_C = c endif @@ -24,8 +32,8 @@ ifeq ($(CONFIG_CMODEL_MEDANY),y) CMODEL = medany endif -ARCH_FLAGS = -march=$(ARCH_BASE)$(ARCH_A)$(ARCH_C) -mabi=$(ABI) \ - -mcmodel=$(CMODEL) +ARCH_FLAGS = -march=$(ARCH_BASE)$(ARCH_A)$(ARCH_F)$(ARCH_D)$(ARCH_C) -mabi=$(ABI) \ + -mcmodel=$(CMODEL) PLATFORM_CPPFLAGS += $(ARCH_FLAGS) CFLAGS_EFI += $(ARCH_FLAGS) -- 2.17.0

3 3

[U-Boot] [PATCH v2 0/9] miscellaneous ubispl and ubi improvements
by Markus Klotzbuecher 29 Jan '20

29 Jan '20

From: Markus Klotzbuecher <markus.klotzbuecher(a)kistler.com> This series contains a couple of UBI and UBI SPL improvements, notably a ubispl extension to allow loading volumes by name. The motivation is to use the UBI atomic volume rename functionality to allow double copy software updates of U-Boot on UBI. To do that we configured the SPL to always load the same volume name (e.g. "u-boot"), and the software updater always installs into the secondary volume "u-boot_r". After a successful upgrade, these two volume names are switched. This extension is protected by #ifdefs as it will somewhat slow down loading of volumes by id. This is because the code needs to disable the optimization of ignoring all volume ids which are not to-be-loaded, since these can only be resolved after attaching. We have tested both with and without fastmap enabled and both paths seems to work reliably. As per Heikos request, this v2 adds two patches that migrate the omap2plus and at91 CONFIG_ENV_* to defconfigs and likewise for the two boards using ubispl. The first migration was supported by an extension to the moveconfig script (patch 1) to expand simple expressions. Both migrations were tested to be binary equal before and after the change. Changes v2: - Add a patch (1) for moveconfig to expand simple expressions - Add patch (3) to move at91 and omap2plus CONFIG_ENV_ to defconfigs - Add patch (7) to migrate boards using ubispl to KConfig - Add missing commit messages - Indicate version of kernel code which was used in ubispl Hamish Guthrie (2): env: ubi: support configurable VID offset ubispl: add support for loading volumes by name Markus Klotzbuecher (7): moveconfig: expand simple expressions env: ubi: KConfig: add CONFIG_ENV_UBI_VOLUME_REDUND at91, omap2plus: configs: migrate CONFIG_ENV_ to defconfigs ubi: fix UBI_SILENCE_MSG ubispl: migrate configuration to Kconfig configs: migrate ubispl boards to KConfig ubispl: introduce separate CONFIG_UBI_SPL_SILENCE_MSG common/spl/Kconfig | 98 ++++++++ common/spl/spl_ubi.c | 7 + configs/am335x_guardian_defconfig | 2 + configs/am335x_igep003x_defconfig | 16 ++ configs/am335x_pdu001_defconfig | 1 + configs/am335x_shc_defconfig | 2 + configs/am335x_shc_ict_defconfig | 2 + configs/am335x_shc_netboot_defconfig | 2 + configs/am335x_shc_sdboot_defconfig | 2 + configs/am335x_sl50_defconfig | 1 + configs/am43xx_evm_defconfig | 1 + configs/am43xx_evm_qspiboot_defconfig | 3 + configs/am43xx_evm_rtconly_defconfig | 1 + configs/am43xx_evm_usbhost_boot_defconfig | 1 + configs/am43xx_hs_evm_defconfig | 1 + configs/at91rm9200ek_defconfig | 3 + configs/at91rm9200ek_ram_defconfig | 3 + configs/at91sam9260ek_dataflash_cs0_defconfig | 3 + configs/at91sam9260ek_dataflash_cs1_defconfig | 3 + configs/at91sam9261ek_dataflash_cs0_defconfig | 3 + configs/at91sam9261ek_dataflash_cs3_defconfig | 3 + configs/at91sam9263ek_dataflash_cs0_defconfig | 3 + configs/at91sam9263ek_dataflash_defconfig | 3 + configs/at91sam9263ek_norflash_boot_defconfig | 3 + configs/at91sam9263ek_norflash_defconfig | 3 + configs/at91sam9g10ek_dataflash_cs0_defconfig | 3 + configs/at91sam9g10ek_dataflash_cs3_defconfig | 3 + configs/at91sam9g20ek_2mmc_defconfig | 2 + configs/at91sam9g20ek_dataflash_cs0_defconfig | 3 + configs/at91sam9g20ek_dataflash_cs1_defconfig | 3 + configs/at91sam9m10g45ek_mmc_defconfig | 1 + configs/at91sam9n12ek_mmc_defconfig | 1 + configs/at91sam9n12ek_spiflash_defconfig | 3 + configs/at91sam9rlek_dataflash_defconfig | 3 + configs/at91sam9rlek_mmc_defconfig | 1 + configs/at91sam9x5ek_dataflash_defconfig | 3 + configs/at91sam9x5ek_mmc_defconfig | 1 + configs/at91sam9x5ek_spiflash_defconfig | 3 + configs/at91sam9xeek_dataflash_cs0_defconfig | 3 + configs/at91sam9xeek_dataflash_cs1_defconfig | 3 + configs/axm_defconfig | 1 + configs/brppt1_mmc_defconfig | 2 + configs/brppt1_nand_defconfig | 2 + configs/brppt1_spi_defconfig | 3 + configs/brxre1_defconfig | 2 + configs/chiliboard_defconfig | 2 + configs/cm_t335_defconfig | 2 + configs/cm_t35_defconfig | 1 + configs/cm_t43_defconfig | 3 + configs/cm_t54_defconfig | 2 + configs/corvus_defconfig | 1 + configs/draco_defconfig | 1 + configs/eco5pk_defconfig | 1 + configs/etamin_defconfig | 2 + configs/ethernut5_defconfig | 3 + .../gardena-smart-gateway-at91sam_defconfig | 4 + configs/gurnard_defconfig | 2 + configs/igep00x0_defconfig | 17 ++ configs/mcx_defconfig | 1 + configs/meesc_dataflash_defconfig | 3 + configs/meesc_defconfig | 1 + configs/mt_ventoux_defconfig | 1 + configs/omap3_overo_defconfig | 1 + configs/omap4_sdp4430_defconfig | 1 + configs/pengwyn_defconfig | 1 + configs/picosam9g45_defconfig | 1 + configs/pm9261_defconfig | 3 + configs/pm9263_defconfig | 3 + configs/pxm2_defconfig | 1 + configs/rastaban_defconfig | 1 + configs/rut_defconfig | 1 + configs/sama5d27_som1_ek_mmc1_defconfig | 1 + configs/sama5d27_som1_ek_mmc_defconfig | 1 + configs/sama5d2_icp_mmc_defconfig | 1 + configs/sama5d2_ptc_ek_mmc_defconfig | 1 + configs/sama5d2_xplained_emmc_defconfig | 1 + configs/sama5d2_xplained_mmc_defconfig | 1 + configs/sama5d2_xplained_spiflash_defconfig | 3 + configs/sama5d36ek_cmp_mmc_defconfig | 1 + configs/sama5d36ek_cmp_spiflash_defconfig | 3 + configs/sama5d3_xplained_mmc_defconfig | 1 + configs/sama5d3xek_mmc_defconfig | 1 + configs/sama5d3xek_spiflash_defconfig | 3 + configs/sama5d4_xplained_mmc_defconfig | 1 + configs/sama5d4_xplained_spiflash_defconfig | 3 + configs/sama5d4ek_mmc_defconfig | 1 + configs/sama5d4ek_spiflash_defconfig | 3 + configs/smartweb_defconfig | 1 + configs/snapper9260_defconfig | 2 + configs/snapper9g20_defconfig | 2 + configs/taurus_defconfig | 1 + configs/thuban_defconfig | 1 + configs/ti816x_evm_defconfig | 2 + configs/tricorder_defconfig | 2 + configs/tricorder_flash_defconfig | 1 + configs/twister_defconfig | 1 + configs/usb_a9263_dataflash_defconfig | 3 + configs/vinco_defconfig | 3 + configs/wb45n_defconfig | 1 + configs/wb50n_defconfig | 1 + drivers/mtd/ubi/Kconfig | 2 +- drivers/mtd/ubi/io.c | 2 + drivers/mtd/ubispl/ubispl.c | 215 +++++++++++++++++- drivers/mtd/ubispl/ubispl.h | 9 +- env/Kconfig | 24 +- env/ubi.c | 17 +- include/configs/am335x_evm.h | 3 - include/configs/am335x_igep003x.h | 23 -- include/configs/am335x_sl50.h | 3 - include/configs/am3517_crane.h | 2 - include/configs/am3517_evm.h | 2 - include/configs/am43xx_evm.h | 5 - include/configs/am57xx_evm.h | 2 - include/configs/at91-sama5_common.h | 5 - include/configs/at91rm9200ek.h | 2 +- include/configs/baltos.h | 3 - include/configs/bav335x.h | 3 - include/configs/brppt1.h | 5 - include/configs/chiliboard.h | 4 - include/configs/cm_t335.h | 2 - include/configs/cm_t35.h | 2 - include/configs/cm_t3517.h | 2 - include/configs/cm_t43.h | 5 - include/configs/corvus.h | 2 - include/configs/devkit8000.h | 6 - include/configs/dra7xx_evm.h | 2 - include/configs/ethernut5.h | 2 - .../configs/gardena-smart-gateway-at91sam.h | 6 - include/configs/kc1.h | 2 - include/configs/mcx.h | 1 - include/configs/nokia_rx51.h | 1 - include/configs/omap3_beagle.h | 4 - include/configs/omap3_cairo.h | 4 - include/configs/omap3_evm.h | 3 - include/configs/omap3_igep00x0.h | 20 -- include/configs/omap3_logic.h | 3 - include/configs/omap3_overo.h | 1 - include/configs/omap3_pandora.h | 3 - include/configs/omap3_zoom1.h | 3 - include/configs/omap5_uevm.h | 2 - include/configs/pcm051.h | 1 - include/configs/pepper.h | 2 - include/configs/siemens-am33x-common.h | 2 - include/configs/smartweb.h | 2 - include/configs/snapper9260.h | 2 - include/configs/snapper9g45.h | 2 - include/configs/sniper.h | 2 - include/configs/tam3517-common.h | 1 - include/configs/tao3530.h | 2 - include/configs/taurus.h | 2 - include/configs/ti814x_evm.h | 1 - include/configs/ti_omap4_common.h | 5 - include/configs/tricorder.h | 2 - include/configs/usb_a9263.h | 3 - include/configs/wb50n.h | 2 - include/ubispl.h | 6 + scripts/config_whitelist.txt | 13 -- tools/moveconfig.py | 41 ++++ 158 files changed, 628 insertions(+), 193 deletions(-) -- 2.20.1

4 23

[U-Boot] [PATCH V2 0/7] ARM: imx: Update Novena to DM/DT
by Marek Vasut 27 Jan '20

27 Jan '20

Update Kosagi Novena to DM / DT and remove the warnings. This depends on the following patches / series: https://patchwork.ozlabs.org/patch/1095618/ https://patchwork.ozlabs.org/patch/1101171/ https://patchwork.ozlabs.org/project/uboot/list/?series=108463 Marek Vasut (7): ARM: dts: imx: novena: Import Novena DT from Linux ARM: imx: novena: Enable DM pin control ARM: imx: novena: Enable DM GPIO ARM: imx: novena: Convert block devices to DM ARM: imx: novena: Enable DM USB ARM: imx: novena: Enable DM PCI ARM: imx: novena: Convert to DM VIDEO arch/arm/dts/Makefile | 3 +- arch/arm/dts/imx6q-novena.dts | 797 ++++++++++++++++++++++++++++++++++ board/kosagi/novena/novena.c | 77 +--- board/kosagi/novena/video.c | 3 + configs/novena_defconfig | 18 +- include/configs/novena.h | 9 +- 6 files changed, 838 insertions(+), 69 deletions(-) create mode 100644 arch/arm/dts/imx6q-novena.dts Cc: Fabio Estevam <fabio.estevam(a)nxp.com> Cc: Stefano Babic <sbabic(a)denx.de> Cc: Vagrant Cascadian <vagrant(a)debian.org> -- 2.20.1

4 25