June 2019 - U-Boot

[U-Boot] [RFC 0/4] Convert fsl_dcu_fb to DM_VIDEO
by Igor Opaniuk 29 Jul '19

29 Jul '19

From: Igor Opaniuk <igor.opaniuk(a)toradex.com> This series of patches refactors and extends NXP DCU video driver to be built with DM_VIDEO enabled. DTS files must additionally include 'u-boot,dm-pre-reloc' property in soc and child nodes to enable driver binding to fsl_dcu_fb device. Current limitations: configuration (display timings etc.) isn't fetched from the DT node. I plan to add this in the next series. Also enables DM_VIDEO by default for Colibri VF. Igor Opaniuk (4): video: fsl_dcu_fb: refactor init functions video: fsl_dcu_fb: add DM_VIDEO support ARM: dts: colibri_vf: Add dcu0 node colibri_vf: enable DM_VIDEO arch/arm/dts/vf-colibri-u-boot.dtsi | 4 + arch/arm/dts/vf-colibri.dtsi | 5 + arch/arm/dts/vf.dtsi | 6 + board/freescale/ls1021aqds/dcu.c | 6 +- board/toradex/colibri_vf/colibri_vf.c | 4 +- board/toradex/colibri_vf/dcu.c | 6 +- configs/colibri_vf_defconfig | 2 +- drivers/video/Kconfig | 2 +- drivers/video/fsl_dcu_fb.c | 213 ++++++++++++++++++-------- include/fsl_dcu_fb.h | 12 +- 10 files changed, 187 insertions(+), 73 deletions(-) -- 2.17.1

3 14

[U-Boot] [PATCH 1/2] ARM: omap3_logic: Enable OMAP EHCI support for SOM-LV Boards
by Adam Ford 28 Jul '19

28 Jul '19

The SOM-LV boards support the OMAP EHCI driver using port 2. With the driver updated to support device tree, this patch sets the corresponding pin muxing for the tranceiver as well as the reset pin. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/board/logicpd/omap3som/omap3logic.h b/board/logicpd/omap3som/omap3logic.h index aeb26b90d7..63c2141783 100644 --- a/board/logicpd/omap3som/omap3logic.h +++ b/board/logicpd/omap3som/omap3logic.h @@ -161,12 +161,14 @@ void set_muxconf_regs(void) MUX_VAL(CP(ETK_D7_ES2), (IEN | PTD | DIS | M0)); /*ETK_D7*/ MUX_VAL(CP(ETK_D8_ES2), (IEN | PTD | DIS | M0)); /*ETK_D8*/ MUX_VAL(CP(ETK_D9_ES2), (IEN | PTD | DIS | M0)); /*ETK_D9*/ +#ifndef CONFIG_USB_EHCI_OMAP /* Torpedo does not use EHCI_OMAP */ MUX_VAL(CP(ETK_D10_ES2), (IEN | PTD | DIS | M0)); /*ETK_D10*/ MUX_VAL(CP(ETK_D11_ES2), (IEN | PTD | DIS | M0)); /*ETK_D11*/ MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M0)); /*ETK_D12*/ MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M0)); /*ETK_D13*/ MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M0)); /*ETK_D14*/ MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M0)); /*ETK_D15*/ +#endif MUX_VAL(CP(D2D_MCAD1), (IEN | PTD | EN | M0)); /*d2d_mcad1*/ MUX_VAL(CP(D2D_MCAD2), (IEN | PTD | EN | M0)); /*d2d_mcad2*/ @@ -231,6 +233,23 @@ void set_muxconf_regs(void) MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)); /*d2d_sread*/ MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)); /*d2d_mbusflag*/ MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)); /*d2d_sbusflag*/ + +#ifdef CONFIG_USB_EHCI_OMAP /* SOM-LV Uses EHCI-OMAP */ + MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M3)); /*HSUSB2_DATA0*/ + MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M3)); /*HSUSB2_DATA1*/ + MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | EN | M0)); /*HSUSB2_DATA2*/ + MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M0)); /*HSUSB2_DATA3*/ + MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M0)); /*HSUSB2_DATA4*/ + MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | DIS | M0)); /*HSUSB2_DATA5*/ + MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M0)); /*HSUSB2_DATA6*/ + MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M0)); /*HSUSB2_DATA7*/ + MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /* GPIO_4 */ + MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTU | DIS | M3)); /*HSUSB2_CLK*/ + MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTU | DIS | M3)); /*HSUSB2_STP*/ + MUX_VAL(CP(ETK_D12_ES2), (IEN | PTU | DIS | M3)); /*HSUSB2_DIR*/ + MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M3)); /*HSUSB2_NXT*/ +#endif + } #endif diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h index e318a9f896..a5ae93914d 100644 --- a/include/configs/omap3_logic.h +++ b/include/configs/omap3_logic.h @@ -30,6 +30,10 @@ /* I2C */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */ +#ifdef CONFIG_USB_EHCI_OMAP +#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 4 +#endif + /* Board NAND Info. */ #ifdef CONFIG_NAND #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */ -- 2.17.1

2 3

[U-Boot] [PATCH] ARM: am3517-evm: Remove non-DM legacy code
by Adam Ford 28 Jul '19

28 Jul '19

With both SPL and U-Boot now supporting DM, we can start removing legacy code. This patch removes the legacy MMC initalization and legacy I2C initialization since both are now available via DM and device tree. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/board/logicpd/am3517evm/am3517evm.c b/board/logicpd/am3517evm/am3517evm.c index e799f80d81..49f8db7ea7 100644 --- a/board/logicpd/am3517evm/am3517evm.c +++ b/board/logicpd/am3517evm/am3517evm.c @@ -116,11 +116,6 @@ int misc_init_r(void) { u32 reset; -#if !defined(CONFIG_DM_I2C) -#ifdef CONFIG_SYS_I2C_OMAP24XX - i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); -#endif -#endif omap_die_id_display(); am3517_evm_musb_init(); @@ -144,12 +139,6 @@ void set_muxconf_regs(void) MUX_AM3517EVM(); } -#if defined(CONFIG_MMC) -int board_mmc_init(bd_t *bis) -{ - return omap_mmc_init(0, 0, 0, -1, -1); -} -#endif #if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) int board_eth_init(bd_t *bis) -- 2.17.1

2 1

[U-Boot] [PATCH] ARM: am3517-evm: Migrate to SPL_OF_CONTROL
by Adam Ford 28 Jul '19

28 Jul '19

Like the other Logic PD OMAP35/DM37 boards, this board has device tree enabled for U-Boot. This patch converts the board to enable SPL_OF_CONTROL and further shrinks the device tree in SPL to limit it to UART3 (console), MMC1, i2c1, and GPIO4 (for mmc1 CD and WP). There appears to be a bug in minicom so users may need to switch the minicom terminal emulation to ANSI from VT102 due to the junk that gets pushed out of the UART on startup. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/arch/arm/dts/am3517-evm-u-boot.dtsi b/arch/arm/dts/am3517-evm-u-boot.dtsi index 59df819f9d..d5a4ce97d1 100644 --- a/arch/arm/dts/am3517-evm-u-boot.dtsi +++ b/arch/arm/dts/am3517-evm-u-boot.dtsi @@ -4,20 +4,40 @@ * Logic PD - http://www.logicpd.com */ +#include "omap3-u-boot.dtsi" + / { - chosen { - stdout-path = &uart3; + aliases { + /delete-property/ serial0; + /delete-property/ serial1; + }; + + ocp@68000000 { + /delete-node/ bandgap@48002524; }; }; -&uart1 { - reg-shift = <2>; +&gpio1 { + /delete-property/ u-boot,dm-spl; +}; + +&gpio2 { + /delete-property/ u-boot,dm-spl; +}; + +&gpio3 { + /delete-property/ u-boot,dm-spl; }; -&uart2 { - reg-shift = <2>; +&gpio5 { + /delete-property/ u-boot,dm-spl; }; -&uart3 { - reg-shift = <2>; +&gpio6 { + /delete-property/ u-boot,dm-spl; }; + +/delete-node/ &uart1; +/delete-node/ &uart2; +/delete-node/ &mmc2; +/delete-node/ &mmc3; diff --git a/configs/am3517_evm_defconfig b/configs/am3517_evm_defconfig index b9f59f3291..64e62a4205 100644 --- a/configs/am3517_evm_defconfig +++ b/configs/am3517_evm_defconfig @@ -1,11 +1,15 @@ CONFIG_ARM=y +# CONFIG_SPL_USE_ARCH_MEMCPY is not set +# CONFIG_TPL_USE_ARCH_MEMCPY is not set +# CONFIG_SPL_USE_ARCH_MEMSET is not set +# CONFIG_TPL_USE_ARCH_MEMSET is not set CONFIG_ARCH_OMAP2PLUS=y CONFIG_SYS_TEXT_BASE=0x80100000 CONFIG_TI_COMMON_CMD_OPTIONS=y -# CONFIG_SPL_GPIO_SUPPORT is not set -CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_SYS_MALLOC_F_LEN=0x4000 CONFIG_TARGET_AM3517_EVM=y CONFIG_EMIF4=y +CONFIG_SPL_SYS_MALLOC_F_LEN=0x3000 CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y @@ -14,7 +18,10 @@ CONFIG_BOOTDELAY=10 CONFIG_VERSION_VARIABLE=y CONFIG_SPL_TEXT_BASE=0x40200000 CONFIG_SPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_SEPARATE_BSS=y +# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set # CONFIG_SPL_FS_EXT4 is not set +# CONFIG_SPL_I2C_SUPPORT is not set CONFIG_SPL_MTD_SUPPORT=y CONFIG_SPL_OS_BOOT=y CONFIG_SYS_PROMPT="AM3517_EVM # " @@ -34,9 +41,13 @@ CONFIG_MTDIDS_DEFAULT="nand0=omap2-nand.0" CONFIG_MTDPARTS_DEFAULT="mtdparts=omap2-nand.0:512k(MLO),1920k(u-boot),256k(u-boot-env),8m(kernel),512k(dtb),-(rootfs)" CONFIG_CMD_UBI=y CONFIG_OF_CONTROL=y +CONFIG_SPL_OF_CONTROL=y CONFIG_DEFAULT_DEVICE_TREE="am3517-evm" # CONFIG_ENV_IS_IN_FAT is not set CONFIG_ENV_IS_IN_NAND=y +CONFIG_SPL_DM=y +CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_SPL_OF_TRANSLATE=y CONFIG_DM_PCA953X=y CONFIG_MMC_OMAP_HS=y CONFIG_NAND=y @@ -49,7 +60,6 @@ CONFIG_DRIVER_TI_EMAC=y CONFIG_PINCTRL=y CONFIG_PINCTRL_SINGLE=y # CONFIG_TWL4030_POWER is not set -CONFIG_CONS_INDEX=3 CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_OMAP3_SPI=y @@ -59,3 +69,4 @@ CONFIG_USB_EHCI_HCD=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_AM35X=y CONFIG_BCH=y +CONFIG_SPL_TINY_MEMSET=y -- 2.17.1

2 1

[U-Boot] [PATCH] ARM: da850-evm: Remove repeated pinmuxing calls
by Adam Ford 28 Jul '19

28 Jul '19

arch_cpu_init() initializes the pinmuxing which is called fairly early in the start sequences, so the board_init function doesn't need to do it again. This patch removes the call from board_init. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/board/davinci/da8xxevm/da850evm.c b/board/davinci/da8xxevm/da850evm.c index c5404e6063..fb1f5750fa 100644 --- a/board/davinci/da8xxevm/da850evm.c +++ b/board/davinci/da8xxevm/da850evm.c @@ -344,10 +344,6 @@ int board_init(void) DAVINCI_SYSCFG_SUSPSRC_UART2), &davinci_syscfg_regs->suspsrc); - /* configure pinmux settings */ - if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes))) - return 1; - #ifdef CONFIG_USE_NOR /* Set the GPIO direction as output */ clrbits_le32((u32 *)GPIO_BANK0_REG_DIR_ADDR, (0x01 << 11)); -- 2.17.1

2 1

[U-Boot] [PATCH] ARM: da850-evm: Remove duplicate UART initialization
by Adam Ford 28 Jul '19

28 Jul '19

The Low Level init functions start the UART, so it doesn't need to happen during board_init. This patch removes it from board_init. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/board/davinci/da8xxevm/da850evm.c b/board/davinci/da8xxevm/da850evm.c index a90b7a3538..c5404e6063 100644 --- a/board/davinci/da8xxevm/da850evm.c +++ b/board/davinci/da8xxevm/da850evm.c @@ -368,11 +368,6 @@ int board_init(void) davinci_emac_mii_mode_sel(HAS_RMII); #endif /* CONFIG_DRIVER_TI_EMAC */ - /* enable the console UART */ - writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST | - DAVINCI_UART_PWREMU_MGMT_UTRST), - &davinci_uart2_ctrl_regs->pwremu_mgmt); - return 0; } -- 2.17.1

2 1

[U-Boot] [PATCH] ARM: am3517-evm: Remove manual ethernet reset code
by Adam Ford 28 Jul '19

28 Jul '19

The reset line going to the ethernet controller is controlled by a global reset controlling multiple peripherals. There is no need to manually invoke the reset. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/board/logicpd/am3517evm/am3517evm.c b/board/logicpd/am3517evm/am3517evm.c index 10031a4801..e799f80d81 100644 --- a/board/logicpd/am3517evm/am3517evm.c +++ b/board/logicpd/am3517evm/am3517evm.c @@ -114,7 +114,6 @@ static void am3517_evm_musb_init(void) */ int misc_init_r(void) { - volatile unsigned int ctr; u32 reset; #if !defined(CONFIG_DM_I2C) @@ -126,35 +125,10 @@ int misc_init_r(void) am3517_evm_musb_init(); - if (gpio_request(PHY_GPIO, "gpio_30") == 0) { - /* activate PHY reset */ - gpio_direction_output(PHY_GPIO, 0); - gpio_set_value(PHY_GPIO, 0); - - ctr = 0; - do { - udelay(1000); - ctr++; - } while (ctr < 300); - - /* deactivate PHY reset */ - gpio_set_value(PHY_GPIO, 1); - - /* allow the PHY to stabilize and settle down */ - ctr = 0; - do { - udelay(1000); - ctr++; - } while (ctr < 300); - - /* ensure that the module is out of reset */ - reset = readl(AM3517_IP_SW_RESET); - reset &= (~CPGMACSS_SW_RST); - writel(reset, AM3517_IP_SW_RESET); - - /* Free requested GPIO */ - gpio_free(PHY_GPIO); - } + /* ensure that the Ethernet module is out of reset */ + reset = readl(AM3517_IP_SW_RESET); + reset &= (~CPGMACSS_SW_RST); + writel(reset, AM3517_IP_SW_RESET); return 0; } -- 2.17.1

2 1

[U-Boot] [PATCH 0/4] MMC Fixes for dra7xx and am57xx boards
by Faiz Abbas 28 Jul '19

28 Jul '19

These patches implement some MMC related fixes for dra7xx and am57xx boards. Faiz Abbas (4): ARM: dts: dra7-mmc-iodelay: Add a new pinctrl group for clk line without pullup ARM: dts: am574x-idk: Add pinmuxes for mmc1 and mmc2 ARM: dts: am57xx: Disable voltage switching for SD card ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values arch/arm/dts/am571x-idk.dts | 10 ++---- arch/arm/dts/am572x-idk.dts | 10 ++---- arch/arm/dts/am574x-idk.dts | 15 ++++++++ arch/arm/dts/am57xx-beagle-x15-common.dtsi | 1 + arch/arm/dts/am57xx-beagle-x15-revb1.dts | 7 +--- arch/arm/dts/am57xx-beagle-x15-revc.dts | 7 +--- arch/arm/dts/am57xx-idk-common.dtsi | 1 + arch/arm/dts/dra7-mmc-iodelay.dtsi | 19 ++++++++++ arch/arm/dts/dra76x-mmc-iodelay.dtsi | 40 +++++++++++----------- 9 files changed, 64 insertions(+), 46 deletions(-) create mode 100644 arch/arm/dts/dra7-mmc-iodelay.dtsi -- 2.19.2

2 8

[U-Boot] [PATCH] ARM: am3517-evm: Enable DM_PMIC and DM_REGULATOR functions
by Adam Ford 28 Jul '19

28 Jul '19

The PBIAS regulator is available on OMAP3's, and it's shared on the AM35, so this patch enables that in U-Boot along with GPIO based regulators. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/configs/am3517_evm_defconfig b/configs/am3517_evm_defconfig index b9f59f3291..f61a86b115 100644 --- a/configs/am3517_evm_defconfig +++ b/configs/am3517_evm_defconfig @@ -17,6 +17,7 @@ CONFIG_SPL_SYS_MALLOC_SIMPLE=y # CONFIG_SPL_FS_EXT4 is not set CONFIG_SPL_MTD_SUPPORT=y CONFIG_SPL_OS_BOOT=y +# CONFIG_SPL_POWER_SUPPORT is not set CONFIG_SYS_PROMPT="AM3517_EVM # " # CONFIG_CMD_IMI is not set CONFIG_CMD_SPL=y @@ -48,6 +49,11 @@ CONFIG_MII=y CONFIG_DRIVER_TI_EMAC=y CONFIG_PINCTRL=y CONFIG_PINCTRL_SINGLE=y +CONFIG_DM_PMIC=y +# CONFIG_SPL_PMIC_CHILDREN is not set +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y # CONFIG_TWL4030_POWER is not set CONFIG_CONS_INDEX=3 CONFIG_SPI=y -- 2.17.1

2 1

[U-Boot] [PATCH v3 00/16] arm: k3: arm64: Initial support for Texas Instrument's J721E Platform
by Lokesh Vutla 28 Jul '19

28 Jul '19

This series adds initial support for Texas Instruments' K3 architecture based J721E SoC. This series depends on the: - mmc series posted by Faiz: https://patchwork.ozlabs.org/project/uboot/list/?series=112948 - sysfw loader series posted by Andreas: https://patchwork.ozlabs.org/project/uboot/list/?series=111844 - exclusive device series posted: https://patchwork.ozlabs.org/project/uboot/list/?series=112440 - arm64 rproc cleanup series: https://patchwork.ozlabs.org/project/uboot/list/?series=112443 Changes since v2: - Dropped an unused macro from PATCH 2/16 Changes since v1: - Updated the DT nodes with exclusive permissions - Fixed up mmc boot mode definition - Added support for fixing up msmc sram - Added custom mmu for armv8 - Added sysfw loader support. The entire series with all the dependencies is available at: https://github.com/lokeshvutla/u-boot/tree/j721e-initial-support Andreas Dannenberg (3): armv7R: K3: j721e: Unlock all applicable control MMR registers armv7R: K3: j721e: Store boot index from ROM armv7R: K3: j721e: Load SYSFW binary and config from boot media Faiz Abbas (1): mmc: am654_sdhci: Separate J721E compatible into 8bit and 4bit versions Lokesh Vutla (10): arm: K3: j721e: Add basic support for J721E SoC definition armv7R: K3: j721e: Add support for boot device detection armv7R: K3: j721e: Shut down R5 core after ATF startup on A72 board: ti: j721e: Add board support for j721e evm dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E arm: dts: ti: Add Support for J721E SoC arm: dts: k3-j721e: Add initial support for common processor board arm: dts: k3-j721e: Add r5 specific dt support configs: j721e_evm_r5: Add initial support configs: j721e_evm_a72: Add initial support Suman Anna (2): armv8: K3: j721e: Add custom MMU support board: ti: j721e: Enable fixing up msmc sram node arch/arm/dts/Makefile | 2 + .../k3-j721e-common-proc-board-u-boot.dtsi | 75 ++++++ arch/arm/dts/k3-j721e-common-proc-board.dts | 63 +++++ arch/arm/dts/k3-j721e-main.dtsi | 231 ++++++++++++++++++ arch/arm/dts/k3-j721e-mcu-wakeup.dtsi | 72 ++++++ .../arm/dts/k3-j721e-r5-common-proc-board.dts | 141 +++++++++++ arch/arm/dts/k3-j721e-som-p0.dtsi | 29 +++ arch/arm/dts/k3-j721e.dtsi | 177 ++++++++++++++ arch/arm/mach-k3/Kconfig | 13 +- arch/arm/mach-k3/Makefile | 1 + arch/arm/mach-k3/am6_init.c | 6 - arch/arm/mach-k3/arm64-mmu.c | 55 +++++ arch/arm/mach-k3/common.c | 6 + arch/arm/mach-k3/include/mach/hardware.h | 4 + .../arm/mach-k3/include/mach/j721e_hardware.h | 49 ++++ arch/arm/mach-k3/include/mach/j721e_spl.h | 31 +++ arch/arm/mach-k3/include/mach/spl.h | 4 + arch/arm/mach-k3/j721e_init.c | 228 +++++++++++++++++ board/ti/j721e/Kconfig | 55 +++++ board/ti/j721e/Makefile | 8 + board/ti/j721e/evm.c | 82 +++++++ configs/j721e_evm_a72_defconfig | 86 +++++++ configs/j721e_evm_r5_defconfig | 95 +++++++ drivers/mmc/am654_sdhci.c | 114 +++++---- include/configs/j721e_evm.h | 103 ++++++++ include/dt-bindings/pinctrl/k3.h | 3 + 26 files changed, 1682 insertions(+), 51 deletions(-) create mode 100644 arch/arm/dts/k3-j721e-common-proc-board-u-boot.dtsi create mode 100644 arch/arm/dts/k3-j721e-common-proc-board.dts create mode 100644 arch/arm/dts/k3-j721e-main.dtsi create mode 100644 arch/arm/dts/k3-j721e-mcu-wakeup.dtsi create mode 100644 arch/arm/dts/k3-j721e-r5-common-proc-board.dts create mode 100644 arch/arm/dts/k3-j721e-som-p0.dtsi create mode 100644 arch/arm/dts/k3-j721e.dtsi create mode 100644 arch/arm/mach-k3/include/mach/j721e_hardware.h create mode 100644 arch/arm/mach-k3/include/mach/j721e_spl.h create mode 100644 arch/arm/mach-k3/j721e_init.c create mode 100644 board/ti/j721e/Kconfig create mode 100644 board/ti/j721e/Makefile create mode 100644 board/ti/j721e/evm.c create mode 100644 configs/j721e_evm_a72_defconfig create mode 100644 configs/j721e_evm_r5_defconfig create mode 100644 include/configs/j721e_evm.h -- 2.21.0

2 33