June 2019 - U-Boot

[U-Boot] cfb_console.c: DM_VIDEO conversion questions/suggestions
by Igor Opaniuk 18 Nov '21

18 Nov '21

Hi everyone, I've finally started looking into the cfb_console.c driver and it's conversion to DM_VIDEO after our initial discussion [1]. Unfortunately I've a bit underestimated the amount of effort that should be done, as mxsfb.c in the Linux mainline obviously pulls the whole core fb subsystem (drivers/video/fbdev/core), which can take a while and frankly I doubt that this is a proper way to do things here. Taking into account that the deadline for DM_VIDEO conversion is 2019.07, it's unlikely that we will manage to do the full conversions this cfb_console driver and all dependent hw specific drivers in a proper way (where we can provide information about videomodes as properties in a proper nodes in DT). Currently the init chain for fb stuff in U-boot (on the other hand, in the Linux, hw specific driver is probed initially, then they trigger fb common routines that are needed from `video/fbdev/core`): stdio_add_devices() -> ./common/stdio.c -> drv_video_init () (drivers/cfb_console.c) - > video_hw_init (particular hw backend, which was statically linked at compile time with a proper video_hw_init() implementation, for example look into mxsfb.c) 2 ways of conversion that come to my mind: 1. Start with simple DM wrappers in cfb_console.c, and introduce dumb DT nodes so the device at least can be probed. All video configuration will be stored the same way as before in the U-boot env (for example, "videomode=video=ctfb:x:640,y:480,depth:18,pclk:39722,le:48,ri:16,up:33,lo:10,hs:96,vs:2,sync:0,vmode:0\0"). Then, step by step, driver by driver, we can move some properties to DT and try to sync Linux/U-boot video DT nodes (at least avoid divergence of tree nodes, so Linux/U-boot video-related DT nodes conform to each other). Yes, this is kind of dirty workaround, but at least this something we can start with, and with minimal amount of intrusive changes. 2. Perform full conversion, where everything works the same way as in Linux kernel. Initially I thought that it could be the proper way to go, but taking into account all differences in the implementation of fb in U-boot/Linux (even the way how the drivers are initialized), I think we will just end up pulling the whole big piece from the Linux kernel, that will definitely take a while (especially further support of this code base, testing/fixing issues etc.). Just to be aware about the amount of effort that should be done: : u-boot.git$ grep -e CONFIG_CFB_CONSOLE -r ./configs/ ./configs/T1042RDB_PI_SDCARD_defconfig:CONFIG_CFB_CONSOLE_ANSI=y ./configs/T1042D4RDB_SDCARD_defconfig:CONFIG_CFB_CONSOLE_ANSI=y ./configs/T1042RDB_PI_NAND_SECURE_BOOT_defconfig:CONFIG_CFB_CONSOLE_ANSI=y ./configs/nokia_rx51_defconfig:CONFIG_CFB_CONSOLE_ANSI=y ./configs/T1042D4RDB_NAND_defconfig:CONFIG_CFB_CONSOLE_ANSI=y ./configs/T1042RDB_PI_SPIFLASH_defconfig:CONFIG_CFB_CONSOLE_ANSI=y ./configs/T1042RDB_PI_NAND_defconfig:CONFIG_CFB_CONSOLE_ANSI=y ./configs/T1042D4RDB_defconfig:CONFIG_CFB_CONSOLE_ANSI=y ./configs/T1042RDB_PI_defconfig:CONFIG_CFB_CONSOLE_ANSI=y ./configs/eb_cpu5282_internal_defconfig:# CONFIG_CFB_CONSOLE is not set ./configs/T1042D4RDB_SPIFLASH_defconfig:CONFIG_CFB_CONSOLE_ANSI=y ./configs/eb_cpu5282_defconfig:# CONFIG_CFB_CONSOLE is not set ./configs/T1042D4RDB_SECURE_BOOT_defconfig:CONFIG_CFB_CONSOLE_ANSI=y Additional Kconfig symbols, that depend on CFB_CONSOLE: * VGA_AS_SINGLE_DEVICE * CONSOLE_EXTRA_INFO * CONSOLE_SCROLL_LINES * SYS_CONSOLE_BG_COL * SYS_CONSOLE_FG_COL Drivers, that don't imply CFG_CONSOLE, but are used alongside with cfb_console.c (kind of particular hw backend driver for fb console): * mxsfb.c * mb862xx.c * sunxi_display.c * ati_radeon_fb.c * fsl_dcu_fb.c * omap3_dss.c * da8xx-fb.c Looking forward to your suggestions/recommendations here (and let me know if I missed something), thanks! [1] https://lists.denx.de/pipermail/u-boot/2019-April/365506.html -- Best regards - Freundliche Grüsse - Meilleures salutations Igor Opaniuk mailto: igor.opaniuk(a)gmail.com skype: igor.opanyuk +380 (93) 836 40 67 http://ua.linkedin.com/in/iopaniuk

5 6

[U-Boot] [PATCH v3 00/20] Bring NAND support to Nintendo NES Classic
by Miquel Raynal 07 Jul '21

07 Jul '21

Hello, This series first adds fixes and enhancements to sunxi NAND drivers (SPL and U-Boot). Once this is done, the SPL NAND driver is converted to use PIO instead of DMA with the goal to support all SoCs with this IP without the need for DMA-related code. Finally, NAND support is added to Nintendo NES Classic through Kconfig and DT additions. Thanks, Miquèl Changes since v2: ================= - Added Boris and Maxime Acked-by tags. - Removed extra space in nand_reset_column() - Fixed the useless wait period on failure in nand_change_column(). - Changed the title "sunxi: allow NAND support to be compiled for..." (removed the "in SPL" precision which is wrong). - Enbraced the deassertion of the reset line by #if statements about the SoCs in use. Wolfgang Denk made a comment on my proposal but I could not find a better solution, so I kept it for now. - s/alwinner,[pin,functions]/[pin,functions]/ in the DT. - Change Alwinner-specific parts in the SPL to generic sentences. Changes since v1: ================= All: ---- - Enhance all commit messages. - Rebased on top of master branch (I should have done that earlier but I forgot I was on an old revision). Fix binman_sym output check --------------------------- - SPL seems to be broken for a few weeks when using raw NAND, fix it by changing the error condition. Fix strength ------------ - Add comment explaining the added line and moved the line for clarification on why it is needed. - Add forgotten Boris' Suggested-by tag. Fix second case of modulo by zero error ---------------------------------------- - Added a reference to the first occurence of this issue. Allow SPL to be compiled for sun8i platforms -------------------------------------------- - This commit is not about compiling the SPL, but the NAND support in the SPL, as corrected by Maxime. Enhancements and cleaning ------------------------- - Patch split into several logical chunks, as requested. - Removed useless udelay(1), that was added for debugging purpose. - Introduced the nand_exec_cmd() helper to mutualize code one step further. - Add an udelay(1) after changing the column to respect the minimum tCCS delay (Change Column Setup time). - Canceled moving to global scope the ecc_strength array. Use PIO instead of DMA ---------------------- - Change commit message/title. - Cancel removing NFC related definitions: they can be useful as the this IP is quite under-documented. - Merge nand_reset_column and nand_change_column (in another patch). - Moved the copy of the data after the check of the ECC status. - ECC chunks are read manually, return if the first chunk is empty only (needed for configuration research), otherwise it should not be treated as an error. Add NAND node to sun8i ---------------------- - U-Boot master branch already has this node, remove the patch. Enable NAND on NES classic -------------------------- - Change the DT cells size from 2 to 1. Add NAND support for NES classic -------------------------------- - Split in several patches, moving SPL_NAND_SUPPORT and NAND_SUNXI out of the defconfig files (NES and CHIP pro) to be automatically selected depending on NAND_SUNXI and ARCH_SUNXI. - Moved the NAND parameters to Kconfig (only for SUNXI because the tool did not work as expected, maybe due to some definitions that are not "numbers" but multiplications and sometimes use other definitions (NAND page size, 2K_SZ, etc). Miquel Raynal (20): spl: fix binman_sym output check mtd: nand: sunxi: fix ECC strength choice spl: nand: sunxi: fix second case of modulo by zero error spl: nand: sunxi: fix typo on register name spl: nand: sunxi: introduce the nand_wait_int() helper spl: nand: sunxi: introduce the nand_wait_cmd_fifo_empty() helper spl: nand: sunxi: add missing status clear spl: nand: sunxi: create an helper to handle command execution spl: nand: sunxi: ensure enough time has passed after changing the column spl: nand: sunxi: make the reset column helper more generic sunxi: spl: deassert the NAND controller reset line spl: nand: sunxi: declare the ecc_bytes array globally spl: nand: sunxi: use PIO instead of DMA sunxi: spl: remove DMA related settings of the NAND controller sunxi: allow NAND support to be compiled for sun8i platforms sunxi: dts: enable NAND on NES classic sunxi: automatically select SPL_NAND_SUPPORT in Kconfig sunxi: make NAND_SUNXI use ARCH_SUNXI as default in Kconfig sunxi: move the NAND parameters to Kconfig configs: add NAND support for NES Classic arch/arm/dts/sun8i-a23-a33.dtsi | 17 ++ .../dts/sun8i-r16-nintendo-nes-classic-edition.dts | 14 ++ arch/arm/include/asm/arch-sunxi/clock_sun6i.h | 6 + board/sunxi/board.c | 7 +- common/spl/spl.c | 10 +- configs/CHIP_pro_defconfig | 6 +- configs/Nintendo_NES_Classic_Edition_defconfig | 4 + drivers/mtd/nand/Kconfig | 26 ++- drivers/mtd/nand/sunxi_nand.c | 8 +- drivers/mtd/nand/sunxi_nand_spl.c | 242 ++++++++++----------- 10 files changed, 208 insertions(+), 132 deletions(-) -- 2.14.1

5 31

[U-Boot] Booting on RK3399
by Simon Glass 19 Nov '20

19 Nov '20

Hi Kever, I have a firefly-rk3399 and would like to boot it into U-Boot (as a start) from an uSD card. Are there instructions somewhere on how to do this? I gather that I need OP-TEE but not how to build it or how to put the image together. I would like to have instructions in README.rockchip if possible. I'm planning to add U-Boot support for bob and maybe kevin (both Chromebooks) but am not sure where to start. I thought the firefly might be best since it is pretty common. Thanks for any help you can provide. Regards, Simon

6 22

[U-Boot] [PATCH v1 00/10] arm: pxa: mmc: add driver model support
by Marcel Ziswiler 30 Jun '20

30 Jun '20

This series, after some initial clean-up, ultimately adds support for the driver model (DM) in the PXA MMC driver. Marcel Ziswiler (10): mmc: add missing space before comment delimiter mmc: fsl_esdhc: annotate endifs serial: pxa: clean-up platform data include file Makefile: allow dm_mmc without of_control dm: core: gracefully handle alias seq without of kconfig: mmc: move pxa_mmc_generic to kconfig arm: pxa: mmc: add driver model support colibri_pxa270_defconfig: enable cmd_dm colibri_pxa270: add mmc platform data colibri_pxa270_defconfig: enable dm_mmc Makefile | 2 +- board/toradex/colibri_pxa270/colibri_pxa270.c | 20 ++- configs/colibri_pxa270_defconfig | 3 + configs/zipitz2_defconfig | 1 + drivers/core/read.c | 4 +- drivers/mmc/Kconfig | 8 + drivers/mmc/fsl_esdhc.c | 4 +- drivers/mmc/mmc.c | 2 +- drivers/mmc/pxa_mmc_gen.c | 160 +++++++++++++++--- include/configs/pxa-common.h | 7 - include/configs/zipitz2.h | 8 - include/dm/platform_data/pxa_mmc_gen.h | 22 +++ include/dm/platform_data/serial_pxa.h | 8 +- include/dm/read.h | 4 + scripts/config_whitelist.txt | 1 - 15 files changed, 196 insertions(+), 58 deletions(-) create mode 100644 include/dm/platform_data/pxa_mmc_gen.h -- 2.21.0

8 32

[U-Boot] [PATCH v2 00/16] Add Intel Stratix 10 SoC support
by Ley Foon Tan 11 Jun '20

11 Jun '20

This is 2nd version of patchset to adds support for Intel Stratix 10 SoC. This patchset is work on top of patchset in [1]. Changes: - update base addresses header - use reset framework for periperhals (16550 UART, MMC, EMAC) - change to use serial DM driver - move bridge command to misc common driver and reuse for other platforms - rework board_init_f() in SPL - update S10 dts and dtsi - Mailbox: - change to use register offset to access register instead of register structure - rename function with __xxx prefix - DDR: - rework DDR driver - change to use register offset to access register instead of register structure - remove union bitwise structure - use wait_for_bit to poll Patchset history: [v1]: https://patchwork.ozlabs.org/cover/900499/ [1]: https://patchwork.ozlabs.org/cover/910018/ Ley Foon Tan (16): arm: socfpga: stratix10: Add watchdog and firewall base addresses arm: socfpga: stratix10: Add clock manager driver for Stratix10 SoC arm: socfpga: stratix10: Add reset manager driver for Stratix10 SoC arm: socfpga: stratix10: Add pinmux support for Stratix10 SoC arm: socfpga: misc: Add CONFIG_SYS_L2_PL310 switch arm: socfpga: misc: Move bridge command to misc common arm: socfpga: stratix10: Add misc support for Stratix10 SoC arm: socfpga: stratix10: Add mailbox support for Stratix10 SoC arm: socfpga: stratix10: Add MMU support for Stratix10 SoC arm: socfpga: Restructure the SPL file arm: socfpga: stratix10: Add SPL driver for Stratix10 SoC arm: socfpga: stratix10: Add timer support for Stratix10 SoC ddr: altera: stratix10: Add DDR support for Stratix10 SoC board: altera: stratix10: Add socdk board support for Stratix10 SoC arm: dts: socfpga: stratix10: update dtsi and dts arm: socfpga: stratix10: Enable Stratix10 SoC build arch/arm/Kconfig | 9 +- arch/arm/dts/socfpga_stratix10.dtsi | 22 +- arch/arm/dts/socfpga_stratix10_socdk.dts | 3 + arch/arm/mach-socfpga/Kconfig | 16 + arch/arm/mach-socfpga/Makefile | 23 +- arch/arm/mach-socfpga/clock_manager.c | 4 +- arch/arm/mach-socfpga/clock_manager_s10.c | 380 +++++++++++++++++++ arch/arm/mach-socfpga/include/mach/base_addr_s10.h | 11 + arch/arm/mach-socfpga/include/mach/clock_manager.h | 2 + .../mach-socfpga/include/mach/clock_manager_s10.h | 210 +++++++++++ arch/arm/mach-socfpga/include/mach/firewall_s10.h | 120 ++++++ arch/arm/mach-socfpga/include/mach/handoff_s10.h | 34 ++ arch/arm/mach-socfpga/include/mach/mailbox_s10.h | 144 ++++++++ arch/arm/mach-socfpga/include/mach/misc.h | 2 + arch/arm/mach-socfpga/include/mach/reset_manager.h | 2 + .../mach-socfpga/include/mach/reset_manager_s10.h | 116 ++++++ arch/arm/mach-socfpga/include/mach/sdram_s10.h | 183 +++++++++ .../arm/mach-socfpga/include/mach/system_manager.h | 5 +- .../mach-socfpga/include/mach/system_manager_s10.h | 176 +++++++++ arch/arm/mach-socfpga/mailbox_s10.c | 380 +++++++++++++++++++ arch/arm/mach-socfpga/misc.c | 34 ++ arch/arm/mach-socfpga/misc_gen5.c | 26 +-- arch/arm/mach-socfpga/misc_s10.c | 133 +++++++ arch/arm/mach-socfpga/mmu-arm64_s10.c | 71 ++++ arch/arm/mach-socfpga/reset_manager.c | 13 + arch/arm/mach-socfpga/reset_manager_s10.c | 140 +++++++ arch/arm/mach-socfpga/spl_a10.c | 105 ++++++ arch/arm/mach-socfpga/{spl.c => spl_gen5.c} | 57 +--- arch/arm/mach-socfpga/spl_s10.c | 199 ++++++++++ arch/arm/mach-socfpga/system_manager_s10.c | 91 +++++ arch/arm/mach-socfpga/timer_s10.c | 26 ++ arch/arm/mach-socfpga/wrap_pinmux_config_s10.c | 56 +++ arch/arm/mach-socfpga/wrap_pll_config_s10.c | 59 +++ board/altera/stratix10-socdk/MAINTAINERS | 7 + board/altera/stratix10-socdk/Makefile | 7 + board/altera/stratix10-socdk/socfpga.c | 7 + configs/socfpga_stratix10_defconfig | 58 +++ drivers/ddr/altera/Makefile | 1 + drivers/ddr/altera/sdram_s10.c | 388 ++++++++++++++++++++ include/configs/socfpga_stratix10_socdk.h | 222 +++++++++++ 40 files changed, 3459 insertions(+), 83 deletions(-) create mode 100644 arch/arm/mach-socfpga/clock_manager_s10.c create mode 100644 arch/arm/mach-socfpga/include/mach/clock_manager_s10.h create mode 100644 arch/arm/mach-socfpga/include/mach/firewall_s10.h create mode 100644 arch/arm/mach-socfpga/include/mach/handoff_s10.h create mode 100644 arch/arm/mach-socfpga/include/mach/mailbox_s10.h create mode 100644 arch/arm/mach-socfpga/include/mach/reset_manager_s10.h create mode 100644 arch/arm/mach-socfpga/include/mach/sdram_s10.h create mode 100644 arch/arm/mach-socfpga/include/mach/system_manager_s10.h create mode 100644 arch/arm/mach-socfpga/mailbox_s10.c create mode 100644 arch/arm/mach-socfpga/misc_s10.c create mode 100644 arch/arm/mach-socfpga/mmu-arm64_s10.c create mode 100644 arch/arm/mach-socfpga/reset_manager_s10.c create mode 100644 arch/arm/mach-socfpga/spl_a10.c rename arch/arm/mach-socfpga/{spl.c => spl_gen5.c} (82%) create mode 100644 arch/arm/mach-socfpga/spl_s10.c create mode 100644 arch/arm/mach-socfpga/system_manager_s10.c create mode 100644 arch/arm/mach-socfpga/timer_s10.c create mode 100644 arch/arm/mach-socfpga/wrap_pinmux_config_s10.c create mode 100644 arch/arm/mach-socfpga/wrap_pll_config_s10.c create mode 100644 board/altera/stratix10-socdk/MAINTAINERS create mode 100644 board/altera/stratix10-socdk/Makefile create mode 100644 board/altera/stratix10-socdk/socfpga.c create mode 100644 configs/socfpga_stratix10_defconfig create mode 100644 drivers/ddr/altera/sdram_s10.c create mode 100644 include/configs/socfpga_stratix10_socdk.h

4 25

[U-Boot] u-boot Marvell ethernet switch development
by Dennis Jacobs 26 May '20

26 May '20

Dear U-boot mailing list, Its the first time I make use of this U-boot mailing list. I am here for a problem I am having recently with u-boot which is part of my graduation project. I am developing firmware for a Marvell Ethernet switch chip (98DX3336) on the RD-XC3-24G4XG-B (Marvell Ethernet switch). Marvell has provided me with U-boot binary files for UART, SPI etc. I managed to load the U-boot UART binary file trough the UART interface. Showing: [cid:image003.png@01D3E22C.D21A6560] Ok so that is good... now I need to set up my own u-boot environment to add some changes. So I did. I Downloaded u-boot 2013.01 and added marvell configurations. I was able to compile and load the U-boot Uart binary trough the UART interface. The terminal is showing the following: [cid:image004.png@01D3E22D.C73E7040] So ok its loads! But now... I can not perform any commands. All commands are Unknown... So what I did was checking the configurations and I found out that I have set the CMD configurations. Like CMD_NET etc etc [cid:image005.png@01D3E22E.7D8A6070] Anny one that could help me here? I would really appreciate it. I am struggling with this problem for almost 2 full days now. Actions I have been taken - Tested if help command was realy executed and no other invisible fragments where added. - Tested the compilation with 7 different armv7-marvell cross compilers Left binary is the working one the second binary is mine. It only differs 26 bytes. I noticed that a different cross compiler also changes the size. Sometime more sometimes less. All of the binarys I compiled where executing correctly but not reacting on anny commands [cid:image006.png@01D3E22F.61EE8C00] Please help me. Kind regards, Dennis Jacobs Designer [Prodrive B.V.]<http://www.prodrive-technologies.com/> Mobile +31 62 57 28 194 Phone +31 40 26 76 200 www.prodrive-technologies.com<http://www.prodrive-technologies.com> [cid:image002.png@01D3E22B.A33384D0] Disclaimer: The content of this e-mail is intended solely for the use of the Individual or entity to whom it is addressed. If you have received this communication in error, be aware that forwarding it, copying it, or in any way disclosing its content to any other person, is strictly prohibited. If you have received this communication in error, please notify the author by replying to this e-mail immediately.

3 2

[U-Boot] [ANN] Monthly developer call
by Tom Rini 21 May '20

21 May '20

Hey all, So as I mentioned back in December[1], I was thinking of doing a recurring community conference call. I've gone ahead and scheduled one now with Zoom (https://zoom.us/) as they work well enough with Linux as a host. For now, the time is 4PM UTC, which is 11AM US Eastern, 8AM US Pacific. The meeting URL is: https://zoom.us/j/203089062 (and so the meeting number is 203089062) For dial-in: +1 (646) 876-9923 and world-wide local dial-in numbers are found on: https://zoom.us/u/acnOQeSN Since we don't do attachments, we do inline patches, what follows is the ics file for the meeting, to import to your favorite (or, least-disliked) calendaring solution: BEGIN:VCALENDAR PRODID:-//zoom.us//iCalendar Event//EN VERSION:2.0 CALSCALE:GREGORIAN METHOD:PUBLISH CLASS:PUBLIC BEGIN:VTIMEZONE TZID:America/New_York TZURL:http://tzurl.org/zoneinfo-outlook/America/New_York X-LIC-LOCATION:America/New_York BEGIN:DAYLIGHT TZOFFSETFROM:-0500 TZOFFSETTO:-0400 TZNAME:EDT DTSTART:19700308T020000 RRULE:FREQ=YEARLY;BYMONTH=3;BYDAY=2SU END:DAYLIGHT BEGIN:STANDARD TZOFFSETFROM:-0400 TZOFFSETTO:-0500 TZNAME:EST DTSTART:19701101T020000 RRULE:FREQ=YEARLY;BYMONTH=11;BYDAY=1SU END:STANDARD END:VTIMEZONE BEGIN:VEVENT DTSTAMP:20190211T165035Z DTSTART;TZID=America/New_York:20190218T110000 DTEND;TZID=America/New_York:20190218T120000 SUMMARY:U-Boot community meeting RRULE:FREQ=MONTHLY;WKST=SU;UNTIL=20191216T170000;INTERVAL=1;BYDAY=3MO UID:ZOOM203089062 TZID:America/New_York DESCRIPTION:Tom Rini is inviting you to a scheduled Zoom meeting.\n\nJoin Zoom Meeting\nhttps://zoom.us/j/203089062\n\nOne tap mobile\n+164687699 23\,\,203089062# US (New York)\n+16699006833\,\,203089062# US (San Jose) \n\nDial by your location\n +1 646 876 9923 US (New York)\n +1 669 900 6833 US (San Jose)\nMeeting ID: 203 089 062\nFind your loca l number: https://zoom.us/u/acnOQeSNf\n LOCATION:https://zoom.us/j/203089062 BEGIN:VALARM TRIGGER:-PT10M ACTION:DISPLAY DESCRIPTION:Reminder END:VALARM END:VEVENT END:VCALENDAR [1]: https://lists.denx.de/pipermail/u-boot/2018-December/350346.html -- Tom

5 15

[U-Boot] [PPC] Internet connection on qemu-ppce500
by vnktux 12 May '20

12 May '20

Hello guys, I am running an image of U-boot 2018.09 in qemu 3.0, the goal would be to load an OS-9 rom file from tftp. The problem is that I can't manage to have an Internet connection in U-boot. No matter how I run the image I always have Net: "No Ethernet found". I run qemu 3.0 with the following command: > qemu-system-ppc -cpu e500v2 -M ppce500 -nographic -kernel ~/u-boot -net nic -net tap,ifname=tap0,script=no I tried to use different -net options in qemu but the problem is always the same. And from the u-boot source code I have edited the board file qemu-ppce500.c in order to have a few ENV variables (since I can't save any env variables from the running U-boot in qemu). > ethact=eTSEC1 > ethprime=eTSEC1 > ethaddr=192.168.10.40 > netmask=255.255.254.0 > serverip=192.168.10.2 > gatewayip=192.168.10.254 The image is compiled using of course: qemu-ppce500_defconfig. What am I doing wrong? Is it even possible to initialize the Ethernet port? Thanks in advance, Vincenzo Sent with [ProtonMail](https://protonmail.com) Secure Email.

3 2

[U-Boot] [PATCH] Makefile: Only build dtc if needed
by Simon Glass 28 Apr '20

28 Apr '20

At present U-Boot always builds dtc if CONFIG_OF_CONTROL is defined. This is wasteful when the system already has a suitable version available. Update the Makefile logic to build dtc only if the version available is too old. This saves about 3 seconds of CPU time on a clean build for me. Signed-off-by: Simon Glass <sjg(a)chromium.org> --- Makefile | 17 +++++++++++++++-- dts/Kconfig | 4 ---- scripts/Kbuild.include | 4 +++- scripts/Makefile | 1 - scripts/dtc-version.sh | 25 ++++++++++++++++++++----- 5 files changed, 38 insertions(+), 13 deletions(-) diff --git a/Makefile b/Makefile index 250eb6c3c39..fec2b2d8fb5 100644 --- a/Makefile +++ b/Makefile @@ -361,7 +361,12 @@ PERL = perl PYTHON ?= python PYTHON2 = python2 PYTHON3 = python3 -DTC ?= $(objtree)/scripts/dtc/dtc + +# DTC is automatically built if the version of $(DTC) is older that needed. +# Use the system dtc if it is new enough. +DTC ?= dtc +DTC_MIN_VERSION := 010406 + CHECK = sparse CHECKFLAGS := -D__linux__ -Dlinux -D__STDC__ -Dunix -D__unix__ \ @@ -926,7 +931,7 @@ endif PHONY += dtbs dtbs: dts/dt.dtb @: -dts/dt.dtb: u-boot +dts/dt.dtb: checkdtc u-boot $(Q)$(MAKE) $(build)=dts dtbs quiet_cmd_copy = COPY $@ @@ -1579,6 +1584,14 @@ SYSTEM_MAP = \ System.map: u-boot @$(call SYSTEM_MAP,$<) > $@ +build_dtc := $(objtree)/scripts/dtc/dtc + +checkdtc: + $(eval DTC := $(call dtc-version,010406,$(build_dtc))) + if test "$(DTC)" = "$(build_dtc)"; then \ + $(MAKE) $(build)=scripts/dtc; \ + fi + ######################################################################### # ARM relocations should all be R_ARM_RELATIVE (32-bit) or diff --git a/dts/Kconfig b/dts/Kconfig index 8917f424445..7e600e28f6c 100644 --- a/dts/Kconfig +++ b/dts/Kconfig @@ -5,9 +5,6 @@ config SUPPORT_OF_CONTROL bool -config DTC - bool - config PYLIBFDT bool @@ -24,7 +21,6 @@ menu "Device Tree Control" config OF_CONTROL bool "Run-time configuration via Device Tree" - select DTC help This feature provides for run-time configuration of U-Boot via a flattened device tree. diff --git a/scripts/Kbuild.include b/scripts/Kbuild.include index 13ebddda65c..82be40cbe78 100644 --- a/scripts/Kbuild.include +++ b/scripts/Kbuild.include @@ -147,8 +147,10 @@ cc-fullversion = $(shell $(CONFIG_SHELL) \ cc-ifversion = $(shell [ $(cc-version) $(1) $(2) ] && echo $(3) || echo $(4)) # added for U-Boot +# $1: min_version +# #2: build_dtc binutils-version = $(shell $(CONFIG_SHELL) $(srctree)/scripts/binutils-version.sh $(AS)) -dtc-version = $(shell $(CONFIG_SHELL) $(srctree)/scripts/dtc-version.sh $(DTC)) +dtc-version = $(shell $(CONFIG_SHELL) $(srctree)/scripts/dtc-version.sh $(DTC) $1 $2) # cc-ldoption # Usage: ldflags += $(call cc-ldoption, -Wl$(comma)--hash-style=both) diff --git a/scripts/Makefile b/scripts/Makefile index e7b353f77f4..cfe9fef8044 100644 --- a/scripts/Makefile +++ b/scripts/Makefile @@ -10,4 +10,3 @@ always := $(hostprogs-y) # Let clean descend into subdirs subdir- += basic kconfig -subdir-$(CONFIG_DTC) += dtc diff --git a/scripts/dtc-version.sh b/scripts/dtc-version.sh index 0744c39eb04..ec988e18daf 100755 --- a/scripts/dtc-version.sh +++ b/scripts/dtc-version.sh @@ -1,12 +1,22 @@ #!/bin/sh # -# dtc-version dtc-command +# dtc-version dtc_command min_version build_dtc # -# Prints the dtc version of `dtc-command' in a canonical 6-digit form -# such as `010404' for dtc 1.4.4 +# Selects which version of dtc to use +# +# If the version of dtc_command is < min_version, prints build_dtc else +# prints dtc_command. The min_version is in the format MMmmpp where: +# +# MM is the major version +# mm is the minor version +# pp is the patch level +# +# For example 010406 means 1.4.6 # -dtc="$*" +dtc="$1" +min_version="$2" +build_dtc="$3" if [ ${#dtc} -eq 0 ]; then echo "Error: No dtc command specified." @@ -18,4 +28,9 @@ MAJOR=$($dtc -v | head -1 | awk '{print $NF}' | cut -d . -f 1) MINOR=$($dtc -v | head -1 | awk '{print $NF}' | cut -d . -f 2) PATCH=$($dtc -v | head -1 | awk '{print $NF}' | cut -d . -f 3 | cut -d - -f 1) -printf "%02d%02d%02d\\n" $MAJOR $MINOR $PATCH +version="$(printf "%02d%02d%02d" $MAJOR $MINOR $PATCH)" +if test $version -lt $min_version; then \ + echo $build_dtc +else + echo $dtc +fi -- 2.19.1.930.g4563a0d9d0-goog

3 7

[U-Boot] [PATCH v1 0/2] stm32f7 gpio driver fixes
by Patrice Chotard 31 Mar '20

31 Mar '20

This series adds: - Fix gpio bank hole management for stm32 F7 and H7 - Fix SPL code size for stm32 F7 Patrice Chotard (2): gpio: stm32f7: Fix gpio bank hole management gpio: stm32f7: Fix SPL code size drivers/gpio/stm32f7_gpio.c | 22 +++++++++++++++++----- 1 file changed, 17 insertions(+), 5 deletions(-) -- 1.9.1

6 11