July 2018 - U-Boot

[U-Boot] [PATCH] ARM: configs: omap3_logic: remove Legacy OMAP3 USB driver
by Adam Ford 24 Jul '18

24 Jul '18

Only the MUSB driver is currently supported on the omap3_logic boards. The driver is using the new-musb and not the legacy version, so this patch removes the dead code references. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/configs/omap3_logic_defconfig b/configs/omap3_logic_defconfig index cd8ffd5adf..ed9f454a5d 100644 --- a/configs/omap3_logic_defconfig +++ b/configs/omap3_logic_defconfig @@ -53,7 +53,6 @@ CONFIG_DM_SPI=y CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_EHCI_HCD=y -CONFIG_USB_OMAP3=y CONFIG_USB_MUSB_GADGET=y CONFIG_USB_MUSB_OMAP2PLUS=y CONFIG_TWL4030_USB=y -- 2.17.1

2 1

[U-Boot] [PATCH] Convert CONFIG_DA8XX_GPIO to Kconfig
by Adam Ford 24 Jul '18

24 Jul '18

This converts the following to Kconfig: CONFIG_DA8XX_GPIO Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/configs/calimain_defconfig b/configs/calimain_defconfig index 7908cfcc34..bc704ff7bd 100644 --- a/configs/calimain_defconfig +++ b/configs/calimain_defconfig @@ -23,6 +23,7 @@ CONFIG_CMD_DIAG=y CONFIG_ENV_IS_IN_FLASH=y CONFIG_BOOTCOUNT_LIMIT=y CONFIG_SYS_BOOTCOUNT_ADDR=0x01C23000 +CONFIG_DA8XX_GPIO=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=y diff --git a/configs/da850_am18xxevm_defconfig b/configs/da850_am18xxevm_defconfig index c76321fb47..3223b44ba5 100644 --- a/configs/da850_am18xxevm_defconfig +++ b/configs/da850_am18xxevm_defconfig @@ -35,6 +35,7 @@ CONFIG_CMD_DIAG=y CONFIG_OF_CONTROL=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_DM=y +CONFIG_DA8XX_GPIO=y CONFIG_DM_I2C=y CONFIG_DM_I2C_COMPAT=y CONFIG_DM_SPI_FLASH=y diff --git a/configs/da850evm_defconfig b/configs/da850evm_defconfig index 6a2b7ae670..b6ec087569 100644 --- a/configs/da850evm_defconfig +++ b/configs/da850evm_defconfig @@ -37,6 +37,7 @@ CONFIG_OF_CONTROL=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_DM=y CONFIG_DM_GPIO=y +CONFIG_DA8XX_GPIO=y CONFIG_DM_I2C=y CONFIG_DM_I2C_COMPAT=y CONFIG_DM_SPI_FLASH=y diff --git a/configs/da850evm_direct_nor_defconfig b/configs/da850evm_direct_nor_defconfig index f71d351ad3..9d6c47df50 100644 --- a/configs/da850evm_direct_nor_defconfig +++ b/configs/da850evm_direct_nor_defconfig @@ -35,6 +35,7 @@ CONFIG_CMD_DIAG=y CONFIG_OF_CONTROL=y CONFIG_ENV_IS_IN_FLASH=y CONFIG_DM=y +CONFIG_DA8XX_GPIO=y CONFIG_DM_I2C=y CONFIG_DM_I2C_COMPAT=y # CONFIG_MMC is not set diff --git a/configs/ea20_defconfig b/configs/ea20_defconfig index 497e5515d7..8d0aac700c 100644 --- a/configs/ea20_defconfig +++ b/configs/ea20_defconfig @@ -29,6 +29,7 @@ CONFIG_CMD_BMP=y CONFIG_CMD_DIAG=y CONFIG_CMD_UBI=y CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_DA8XX_GPIO=y # CONFIG_MMC is not set CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_STMICRO=y diff --git a/configs/ipam390_defconfig b/configs/ipam390_defconfig index 15c4944b3b..4256730e4c 100644 --- a/configs/ipam390_defconfig +++ b/configs/ipam390_defconfig @@ -33,5 +33,6 @@ CONFIG_MTDPARTS_DEFAULT="mtdparts=davinci_nand.0:128k(u-boot-env),1408k(u-boot), CONFIG_CMD_DIAG=y CONFIG_CMD_UBI=y CONFIG_ENV_IS_IN_NAND=y +CONFIG_DA8XX_GPIO=y # CONFIG_MMC is not set CONFIG_SYS_NS16550=y diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index 29af22ecc7..9caa87846c 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -58,6 +58,11 @@ config ATMEL_PIO4 may be dedicated as a general purpose I/O or be assigned to a function of an embedded peripheral. +config DA8XX_GPIO + bool "DA8xx GPIO Driver" + help + This driver supports the DA8xx GPIO controller + config INTEL_BROADWELL_GPIO bool "Intel Broadwell GPIO driver" depends on DM diff --git a/include/configs/calimain.h b/include/configs/calimain.h index ab4a9e6ddc..690f605695 100644 --- a/include/configs/calimain.h +++ b/include/configs/calimain.h @@ -26,7 +26,6 @@ #define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE #define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) #define CONFIG_ARCH_CPU_INIT -#define CONFIG_DA8XX_GPIO #define CONFIG_HW_WATCHDOG #define CONFIG_SYS_WDTTIMERBASE DAVINCI_TIMER1_BASE #define CONFIG_SYS_WDT_PERIOD_LOW \ diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h index 6690be60b6..a8d4894bee 100644 --- a/include/configs/da850evm.h +++ b/include/configs/da850evm.h @@ -226,7 +226,6 @@ #define CONFIG_MTD_PARTITIONS /* required for UBI partition support */ #endif -#define CONFIG_DA8XX_GPIO /* * U-Boot general configuration */ diff --git a/include/configs/ea20.h b/include/configs/ea20.h index c84cd962d7..5e6f0c23d2 100644 --- a/include/configs/ea20.h +++ b/include/configs/ea20.h @@ -28,7 +28,6 @@ #define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE #define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) #define CONFIG_SKIP_LOWLEVEL_INIT -#define CONFIG_DA8XX_GPIO /* * Memory Info diff --git a/include/configs/ipam390.h b/include/configs/ipam390.h index faf21ddb08..3b13798529 100644 --- a/include/configs/ipam390.h +++ b/include/configs/ipam390.h @@ -238,7 +238,6 @@ #define CONFIG_SYS_SPL_ARGS_ADDR LINUX_BOOT_PARAM_ADDR /* GPIO support */ -#define CONFIG_DA8XX_GPIO #define CONFIG_IPAM390_GPIO_BOOTMODE ((16 * 7) + 14) #define CONFIG_SHOW_BOOT_PROGRESS diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 8ded15c89a..120212c4a6 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -309,7 +309,6 @@ CONFIG_CUSTOMER_BOARD_SUPPORT CONFIG_D2NET_V2 CONFIG_DA850_AM18X_EVM CONFIG_DA850_EVM_MAX_CPU_CLK -CONFIG_DA8XX_GPIO CONFIG_DBAU1000 CONFIG_DBGU CONFIG_DBG_MONITOR -- 2.17.1

2 1

[U-Boot] [PATCH] ARM: DTS: am3517-evm-u-boot: Mark MMC1 with cd-inverted
by Adam Ford 24 Jul '18

24 Jul '18

In order to use the device tree for MMC, the card-detect pin needs to be inverted. This patch places this into the am3517-evm-u-boot.dtsi file to keep the main DTS and DTSI files clean and in-sync with Linux Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/arch/arm/dts/am3517-evm-u-boot.dtsi b/arch/arm/dts/am3517-evm-u-boot.dtsi index 59df819f9d..c02beaad77 100644 --- a/arch/arm/dts/am3517-evm-u-boot.dtsi +++ b/arch/arm/dts/am3517-evm-u-boot.dtsi @@ -10,6 +10,10 @@ }; }; +&mmc1 { + cd-inverted; +}; + &uart1 { reg-shift = <2>; }; -- 2.17.1

2 1

[U-Boot] [PATCH] ARM: dts: am3517-evm-uboot: Add reg-shift for UART
by Adam Ford 24 Jul '18

24 Jul '18

With the resync of the omap3.dtsi file, the reg-shift was removed so it breaks the UART. Adding the reg-shift into the am3517-evm-u-boot.dtsi keeps the reg-shift for U-Boot, but keeps the dts/dtsi files clean from Linux. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/arch/arm/dts/am3517-evm-u-boot.dtsi b/arch/arm/dts/am3517-evm-u-boot.dtsi index f049a6452e..59df819f9d 100644 --- a/arch/arm/dts/am3517-evm-u-boot.dtsi +++ b/arch/arm/dts/am3517-evm-u-boot.dtsi @@ -9,3 +9,15 @@ stdout-path = &uart3; }; }; + +&uart1 { + reg-shift = <2>; +}; + +&uart2 { + reg-shift = <2>; +}; + +&uart3 { + reg-shift = <2>; +}; -- 2.17.1

2 1

[U-Boot] [PATCH] mtd: nand: add new enum for storing ECC algorithm
by Philippe Reynes 24 Jul '18

24 Jul '18

From: Rafał Miłecki <zajec5(a)gmail.com> Our nand_ecc_modes_t is already a bit abused by value NAND_ECC_SOFT_BCH. This enum should store ECC mode only and putting algorithm details there is a bad idea. It would result in too many values impossible to support in a sane way. To solve this problem let's add a new enum. We'll have to modify all drivers to set it properly but once it's done it'll be possible to drop NAND_ECC_SOFT_BCH. That will result in a cleaner design and more possibilities like setting ECC algorithm for hardware ECC mode. Signed-off-by: Rafał Miłecki <zajec5(a)gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon(a)free-electrons.com> [Linux commit: b0fcd8ab7b3c89b5da7fff5224d06ed73e7a33cc] [Philippe Reynes: adapt code to u-boot] Signed-off-by: Philippe Reynes <philippe.reynes(a)softathome.com> --- include/linux/mtd/rawnand.h | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h index cdad7b8..9f5dc81 100644 --- a/include/linux/mtd/rawnand.h +++ b/include/linux/mtd/rawnand.h @@ -143,6 +143,12 @@ typedef enum { NAND_ECC_SOFT_BCH, } nand_ecc_modes_t; +enum nand_ecc_algo { + NAND_ECC_UNKNOWN, + NAND_ECC_HAMMING, + NAND_ECC_BCH, +}; + /* * Constants for Hardware ECC */ @@ -533,6 +539,7 @@ static const struct nand_ecc_caps __name = { \ /** * struct nand_ecc_ctrl - Control structure for ECC * @mode: ECC mode + * @algo: ECC algorithm * @steps: number of ECC steps per page * @size: data bytes per ECC step * @bytes: ECC bytes per step @@ -583,6 +590,7 @@ static const struct nand_ecc_caps __name = { \ */ struct nand_ecc_ctrl { nand_ecc_modes_t mode; + enum nand_ecc_algo algo; int steps; int size; int bytes; -- 2.7.4

2 1

[U-Boot] [PATCH 2/2] ARM: DTS: Resync Logic PD SOM-LV 37xx devkit with Linux 4.18-RC4
by Adam Ford 24 Jul '18

24 Jul '18

There have been some significant changes to the DM37 SOM-LV device tree. This patch re-syncs it with Linux. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts b/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts index 1702b9e3db..2428373952 100644 --- a/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts +++ b/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts @@ -8,262 +8,10 @@ #include "omap36xx.dtsi" #include "logicpd-som-lv.dtsi" +#include "logicpd-som-lv-baseboard.dtsi" #include "omap-gpmc-smsc9221.dtsi" / { model = "LogicPD Zoom DM3730 SOM-LV Development Kit"; compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3"; - - chosen { - stdout-path = &uart1; - }; - - gpio_keys { - compatible = "gpio-keys"; - pinctrl-names = "default"; - pinctrl-0 = <&gpio_key_pins>; - - sysboot2 { - label = "gpio3"; - gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* gpio_111 / uP_GPIO_3 */ - linux,code = <BTN_0>; - wakeup-source; - }; - }; - - sound { - compatible = "ti,omap-twl4030"; - ti,model = "omap3logic"; - ti,mcbsp = <&mcbsp2>; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins &led_pins_wkup>; - - led1 { - label = "led1"; - gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* gpio133 */ - linux,default-trigger = "cpu0"; - }; - - led2 { - label = "led2"; - gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; /* gpio11 */ - linux,default-trigger = "none"; - }; - }; -}; - -&vaux1 { - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; -}; - -&vaux4 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; -}; - -&mcbsp2 { - status = "okay"; -}; - -&charger { - ti,bb-uvolt = <3200000>; - ti,bb-uamp = <150>; -}; - -&gpmc { - ranges = <1 0 0x08000000 0x1000000>; /* CS1: 16MB for LAN9221 */ - - ethernet@gpmc { - pinctrl-names = "default"; - pinctrl-0 = <&lan9221_pins>; - interrupt-parent = <&gpio5>; - interrupts = <24 IRQ_TYPE_LEVEL_LOW>; /* gpio_152 */ - reg = <1 0 0xff>; - }; -}; - -&vpll2 { - regulator-always-on; -}; - -&dss { - status = "ok"; - vdds_dsi-supply = <&vpll2>; - vdda_video-supply = <&video_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&dss_dpi_pins1>; - port { - dpi_out: endpoint { - remote-endpoint = <&lcd_in>; - data-lines = <16>; - }; - }; -}; - -/ { - aliases { - display0 = &lcd0; - }; - - video_reg: video_reg { - compatible = "regulator-fixed"; - regulator-name = "fixed-supply"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - lcd0: display@0 { - compatible = "panel-dpi"; - label = "28"; - status = "okay"; - /* default-on; */ - pinctrl-names = "default"; - pinctrl-0 = <&lcd_enable_pin>; - enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ - port { - lcd_in: endpoint { - remote-endpoint = <&dpi_out>; - }; - }; - - panel-timing { - clock-frequency = <9000000>; - hactive = <480>; - vactive = <272>; - hfront-porch = <3>; - hback-porch = <2>; - hsync-len = <42>; - vback-porch = <3>; - vfront-porch = <2>; - vsync-len = <11>; - hsync-active = <1>; - vsync-active = <1>; - de-active = <1>; - pixelclk-active = <0>; - }; - }; - - bl: backlight { - compatible = "pwm-backlight"; - pinctrl-names = "default"; - pinctrl-0 = <&backlight_pins>; - pwms = <&twl_pwm 0 5000000>; - brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; - default-brightness-level = <7>; - enable-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* gpio_8 */ - }; -}; - -&mmc1 { - interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>; - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins>; - vmmc-supply = <&vmmc1>; - bus-width = <4>; - cap-power-off-card; -}; - -&mmc2 { - status = "disabled"; -}; - -&omap3_pmx_core { - gpio_key_pins: pinmux_gpio_key_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_xclkb.gpio_111 / uP_GPIO_3*/ - >; - }; - - led_pins: pinmux_led_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x215e, PIN_OUTPUT_PULLUP | MUX_MODE4) /* sdmmc2_dat1.gpio_133 / uP_GPIO_0 */ - >; - }; - - lan9221_pins: pinmux_lan9221_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ - >; - }; - - mmc1_pins: pinmux_mmc1_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ - OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ - OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ - OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ - OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ - OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ - OMAP3_CORE1_IOPAD(0x2132, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_strobe.gpio_126 */ - OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_d11.gpio_110 */ - >; - }; - - lcd_enable_pin: pinmux_lcd_enable_pin { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */ - >; - }; - - dss_dpi_pins1: pinmux_dss_dpi_pins1 { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */ - OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */ - OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */ - OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */ - - OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data0.dss_data0 */ - OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data1.dss_data1 */ - OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data2.dss_data2 */ - OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data3.dss_data3 */ - OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data4.dss_data4 */ - OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data5.dss_data5 */ - OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */ - OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */ - OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */ - OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */ - OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */ - OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */ - OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */ - OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */ - OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */ - OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */ - >; - }; -}; - -&omap3_pmx_wkup { - led_pins_wkup: pinmux_led_pins_wkup { - pinctrl-single,pins = < - OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu0.gpio_11 / uP_GPIO_1 */ - >; - }; - - backlight_pins: pinmux_backlight_pins { - pinctrl-single,pins = < - OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* sys_boot6.gpio_8 */ - >; - }; -}; - - -&uart1 { - interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>; -}; - -/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */ -&usb_otg_hs { - pinctrl-names = "default"; - pinctrl-0 = <&hsusb_otg_pins>; - interface-type = <0>; - usb-phy = <&usb2_phy>; - phys = <&usb2_phy>; - phy-names = "usb2-phy"; - mode = <3>; - power = <50>; }; diff --git a/arch/arm/dts/logicpd-som-lv-baseboard.dtsi b/arch/arm/dts/logicpd-som-lv-baseboard.dtsi new file mode 100644 index 0000000000..4990ed90dc --- /dev/null +++ b/arch/arm/dts/logicpd-som-lv-baseboard.dtsi @@ -0,0 +1,256 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/ { + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_key_pins>; + + sysboot2 { + label = "gpio3"; + gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* gpio_111 / uP_GPIO_3 */ + linux,code = <BTN_0>; + wakeup-source; + }; + }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3logic"; + ti,mcbsp = <&mcbsp2>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins &led_pins_wkup>; + + led1 { + label = "led1"; + gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* gpio133 */ + linux,default-trigger = "cpu0"; + }; + + led2 { + label = "led2"; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; /* gpio11 */ + linux,default-trigger = "none"; + }; + }; +}; + +&vaux1 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; +}; + +&vaux4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +&mcbsp2 { + status = "okay"; +}; + +&charger { + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */ + 1 0 0x2c000000 0x1000000 /* CS1: 16MB for LAN9221 */ + 2 0 0x10000000 0x2000000>; /* CS2: 32MB for NOR */ + + ethernet@gpmc { + pinctrl-names = "default"; + pinctrl-0 = <&lan9221_pins>; + interrupt-parent = <&gpio5>; + interrupts = <24 IRQ_TYPE_LEVEL_LOW>; /* gpio_152 */ + reg = <1 0 0xff>; + }; +}; + +&vpll2 { + regulator-always-on; +}; + +&dss { + status = "ok"; + vdds_dsi-supply = <&vpll2>; + vdda_video-supply = <&video_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins1>; + port { + dpi_out: endpoint { + remote-endpoint = <&lcd_in>; + data-lines = <16>; + }; + }; +}; + +/ { + aliases { + display0 = &lcd0; + }; + + video_reg: video_reg { + compatible = "regulator-fixed"; + regulator-name = "fixed-supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + lcd0: display@0 { + compatible = "panel-dpi"; + label = "28"; + status = "okay"; + /* default-on; */ + pinctrl-names = "default"; + pinctrl-0 = <&lcd_enable_pin>; + enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <3>; + hback-porch = <2>; + hsync-len = <42>; + vback-porch = <3>; + vfront-porch = <2>; + vsync-len = <11>; + hsync-active = <1>; + vsync-active = <1>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + + bl: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&backlight_pins>; + pwms = <&twl_pwm 0 5000000>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <7>; + enable-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* gpio_8 */ + }; +}; + +&mmc1 { + interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>; /* gpio_126 */ + cd-gpios = <&gpio4 14 IRQ_TYPE_LEVEL_LOW>; /* gpio_110 */ + vmmc-supply = <&vmmc1>; + bus-width = <4>; + cap-power-off-card; +}; + +&omap3_pmx_core { + gpio_key_pins: pinmux_gpio_key_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_xclkb.gpio_111 / uP_GPIO_3*/ + >; + }; + + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x215e, PIN_OUTPUT_PULLUP | MUX_MODE4) /* sdmmc2_dat1.gpio_133 / uP_GPIO_0 */ + >; + }; + + lan9221_pins: pinmux_lan9221_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + OMAP3_CORE1_IOPAD(0x2132, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_strobe.gpio_126 */ + OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_d11.gpio_110 */ + >; + }; + + lcd_enable_pin: pinmux_lcd_enable_pin { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */ + >; + }; + + dss_dpi_pins1: pinmux_dss_dpi_pins1 { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */ + + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data0.dss_data0 */ + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data1.dss_data1 */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data2.dss_data2 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data3.dss_data3 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data4.dss_data4 */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data5.dss_data5 */ + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */ + >; + }; +}; + +&omap3_pmx_wkup { + led_pins_wkup: pinmux_led_pins_wkup { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu0.gpio_11 / uP_GPIO_1 */ + >; + }; + + backlight_pins: pinmux_backlight_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* sys_boot6.gpio_8 */ + >; + }; +}; + + +&uart1 { + interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>; +}; + +/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */ +&usb_otg_hs { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb_otg_pins>; + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; diff --git a/arch/arm/dts/logicpd-som-lv.dtsi b/arch/arm/dts/logicpd-som-lv.dtsi index c1aa7a4518..3bb28c03ca 100644 --- a/arch/arm/dts/logicpd-som-lv.dtsi +++ b/arch/arm/dts/logicpd-som-lv.dtsi @@ -26,7 +26,7 @@ gpio = <&gpio1 3 0>; /* gpio_3 */ startup-delay-us = <70000>; enable-active-high; - vin-supply = <&vmmc2>; + vin-supply = <&vaux3>; }; /* HS USB Host PHY on PORT 1 */ @@ -35,6 +35,13 @@ reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */ #phy-cells = <0>; }; + + /* fixed 26MHz oscillator */ + hfclk_26m: oscillator { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <26000000>; + }; }; &gpmc { @@ -71,26 +78,54 @@ }; &i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; clock-frequency = <2600000>; twl: twl@48 { reg = <0x48>; interrupts = <7>; /* SYS_NIRQ cascaded to intc */ interrupt-parent = <&intc>; + clocks = <&hfclk_26m>; + clock-names = "fck"; twl_audio: audio { compatible = "ti,twl4030-audio"; codec { + ti,hs_extmute_gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>; }; }; }; }; &i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; clock-frequency = <400000>; }; &i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; clock-frequency = <400000>; + + touchscreen: tsc2004@48 { + compatible = "ti,tsc2004"; + reg = <0x48>; + vio-supply = <&vaux1>; + pinctrl-names = "default"; + pinctrl-0 = <&tsc2004_pins>; + interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; }; &mmc3 { @@ -189,7 +224,19 @@ >; }; + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ + OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ + OMAP3_CORE1_IOPAD(0x20ba, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs6.gpio_57 */ + >; + }; + tsc2004_pins: pinmux_tsc2004_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */ + >; + }; }; &omap3_pmx_wkup { @@ -202,10 +249,22 @@ }; wl127x_gpio: pinmux_wl127x_gpio_pin { pinctrl-single,pins = < - OMAP3_WKUP_IOPAD(0x2a0c, PIN_INPUT | MUX_MODE4) /* sys_boot0.gpio_2 */ + OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4) /* sys_boot0.gpio_2 */ OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */ >; }; + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */ + OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */ + >; + }; + i2c3_pins: pinmux_i2c3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */ + OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */ + >; + }; }; &omap3_pmx_core2 { @@ -237,6 +296,11 @@ #include "twl4030.dtsi" #include "twl4030_omap3.dtsi" +&vaux3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + &twl { twl_power: power { compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle"; -- 2.17.1

2 1

[U-Boot] [PATCH 1/2] ARM: DTS: Resync LogicPD-Torpedo-37xx-devkit with Linux 4.18-RC4
by Adam Ford 24 Jul '18

24 Jul '18

There have been some refactoring of the DTS files for the Logic PD DM37 Torpedo. This patch re-sync's the DTS files with Linux Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts index 43e9364083..234afd6d60 100644 --- a/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts +++ b/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts @@ -9,396 +9,69 @@ #include "omap36xx.dtsi" #include "logicpd-torpedo-som.dtsi" #include "omap-gpmc-smsc9221.dtsi" +#include "logicpd-torpedo-baseboard.dtsi" / { model = "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit"; compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3"; - gpio_keys { - compatible = "gpio-keys"; - pinctrl-names = "default"; - pinctrl-0 = <&gpio_key_pins &gpio_key_pins_wkup>; - - sysboot2 { - label = "sysboot2"; - gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; /* gpio2 */ - linux,code = <BTN_0>; - wakeup-source; - }; - - sysboot5 { - label = "sysboot5"; - gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; /* gpio7 */ - linux,code = <BTN_1>; - wakeup-source; - }; - - gpio1 { - label = "gpio1"; - gpios = <&gpio6 21 GPIO_ACTIVE_LOW>; /* gpio181 */ - linux,code = <BTN_2>; - wakeup-source; - }; - - gpio2 { - label = "gpio2"; - gpios = <&gpio6 18 GPIO_ACTIVE_LOW>; /* gpio178 */ - linux,code = <BTN_3>; - wakeup-source; - }; - }; - - sound { - compatible = "ti,omap-twl4030"; - ti,model = "omap3logic"; - ti,mcbsp = <&mcbsp2>; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins>; - - led1 { - label = "led1"; - gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>; /* gpio180 */ - linux,default-trigger = "cpu0"; - }; - - led2 { - label = "led2"; - gpios = <&gpio6 19 GPIO_ACTIVE_HIGH>; /* gpio179 */ - linux,default-trigger = "none"; - }; - }; - - pwm10: dmtimer-pwm { - compatible = "ti,omap-dmtimer-pwm"; - pinctrl-names = "default"; - pinctrl-0 = <&pwm_pins>; - ti,timers = <&timer10>; - #pwm-cells = <3>; - }; - -}; - -&vaux1 { - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; -}; - -&vaux4 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; -}; - -&mcbsp2 { - status = "okay"; -}; - -&charger { - ti,bb-uvolt = <3200000>; - ti,bb-uamp = <150>; -}; - -&gpmc { - ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */ - 1 0 0x2c000000 0x1000000>; /* CS1: 16MB for LAN9221 */ - - ethernet@gpmc { - pinctrl-names = "default"; - pinctrl-0 = <&lan9221_pins>; - interrupt-parent = <&gpio5>; - interrupts = <1 IRQ_TYPE_LEVEL_LOW>; /* gpio129 */ - reg = <1 0 0xff>; - }; -}; - -&vpll2 { - regulator-always-on; -}; - -&dss { - status = "ok"; - vdds_dsi-supply = <&vpll2>; - vdda_video-supply = <&video_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&dss_dpi_pins1>; - port { - dpi_out: endpoint { - remote-endpoint = <&lcd_in>; - data-lines = <16>; - }; - }; -}; - -/ { - aliases { - display0 = &lcd0; - }; - - video_reg: video_reg { - pinctrl-names = "default"; - pinctrl-0 = <&panel_pwr_pins>; + wl12xx_vmmc: wl12xx_vmmc { compatible = "regulator-fixed"; - regulator-name = "fixed-supply"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ - }; - - lcd0: display { - compatible = "panel-dpi"; - label = "15"; - status = "okay"; - /* default-on; */ - pinctrl-names = "default"; - - port { - lcd_in: endpoint { - remote-endpoint = <&dpi_out>; - }; - }; - - panel-timing { - clock-frequency = <9000000>; - hactive = <480>; - vactive = <272>; - hfront-porch = <3>; - hback-porch = <2>; - hsync-len = <42>; - vback-porch = <3>; - vfront-porch = <4>; - vsync-len = <11>; - hsync-active = <0>; - vsync-active = <0>; - de-active = <1>; - pixelclk-active = <1>; - }; - }; - - bl: backlight { - compatible = "pwm-backlight"; - pinctrl-names = "default"; - pinctrl-0 = <&backlight_pins>; - pwms = <&pwm10 0 5000000 0>; - brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; - default-brightness-level = <7>; - enable-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; /* gpio_154 */ + regulator-name = "vwl1271"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio5 29 0>; /* gpio157 */ + startup-delay-us = <70000>; + enable-active-high; + vin-supply = <&vmmc2>; }; }; -&mmc1 { - interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>; +/* + * Only found on the wireless SOM. For the SOM without wireless, the pins for + * MMC3 can be routed with jumpers to the second MMC slot on the devkit and + * gpio157 is not connected. So this should be OK to keep common for now, + * probably device tree overlays is the way to go with the various SOM and + * jumpering combinations for the long run. + */ +&mmc3 { + interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>; + pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>; pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins &mmc1_cd>; - cd-gpios = <&gpio4 31 IRQ_TYPE_LEVEL_LOW>; /* gpio127 */ - vmmc-supply = <&vmmc1>; + vmmc-supply = <&wl12xx_vmmc>; + non-removable; bus-width = <4>; cap-power-off-card; + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1283"; + reg = <2>; + interrupt-parent = <&gpio5>; + interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */ + ref-clock-frequency = <26000000>; + tcxo-clock-frequency = <26000000>; + }; }; &omap3_pmx_core { - gpio_key_pins: pinmux_gpio_key_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_clk.gpio_178 */ - OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_cs0.gpio_181 */ - >; - }; - - pwm_pins: pinmux_pwm_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* gpmc_ncs5.gpt_10_pwm_evt */ - >; - }; - - led_pins: pinmux_led_pins { + mmc3_pins: pinmux_mm3_pins { pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x21d8, PIN_OUTPUT | MUX_MODE4) /* gpio_179 */ - OMAP3_CORE1_IOPAD(0x21da, PIN_OUTPUT | MUX_MODE4) /* gpio_180 */ - >; - }; - - mmc1_pins: pinmux_mmc1_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ - OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ - OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ - OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ - OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ - OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ - >; - }; - - tsc2004_pins: pinmux_tsc2004_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */ - >; - }; - - backlight_pins: pinmux_backlight_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_dx.gpio_154 */ - >; - }; - - isp_pins: pinmux_isp_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE0) /* cam_hs.cam_hs */ - OMAP3_CORE1_IOPAD(0x210e, PIN_INPUT | MUX_MODE0) /* cam_vs.cam_vs */ - OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT | MUX_MODE0) /* cam_xclka.cam_xclka */ - OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT | MUX_MODE0) /* cam_pclk.cam_pclk */ - - OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT | MUX_MODE0) /* cam_d0.cam_d0 */ - OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT | MUX_MODE0) /* cam_d1.cam_d1 */ - OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT | MUX_MODE0) /* cam_d2.cam_d2 */ - OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE0) /* cam_d3.cam_d3 */ - OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT | MUX_MODE0) /* cam_d4.cam_d4 */ - OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT | MUX_MODE0) /* cam_d5.cam_d5 */ - OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0) /* cam_d6.cam_d6 */ - OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0) /* cam_d7.cam_d7 */ - >; - }; - - panel_pwr_pins: pinmux_panel_pwr_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */ - >; - }; - - dss_dpi_pins1: pinmux_dss_dpi_pins1 { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */ - OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */ - OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */ - OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */ - - OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */ - OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */ - OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */ - OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */ - OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */ - OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */ - OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */ - OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */ - OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */ - OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */ - OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data16.dss_data16 */ - OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data17.dss_data17 */ - - OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data18.dss_data0 */ - OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data19.dss_data1 */ - OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data20.dss_data2 */ - OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data21.dss_data3 */ - OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data22.dss_data4 */ - OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data23.dss_data5 */ + OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */ + OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */ + OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */ + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */ + OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ + OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */ >; }; }; -&omap3_pmx_wkup { - gpio_key_pins_wkup: pinmux_gpio_key_pins_wkup { - pinctrl-single,pins = < - OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot0.gpio_2 */ - OMAP3_WKUP_IOPAD(0x2a14, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot5.gpio_7 */ - >; - }; - - lan9221_pins: pinmux_lan9221_pins { - pinctrl-single,pins = < - OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4) /* reserved.gpio_129 */ - >; - }; - - mmc1_cd: pinmux_mmc1_cd { +&omap3_pmx_core2 { + mmc3_core2_pins: pinmux_mmc3_core2_pins { pinctrl-single,pins = < - OMAP3_WKUP_IOPAD(0x2a54, PIN_INPUT_PULLUP | MUX_MODE4) /* reserved.gpio_127 */ + OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ + OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ >; }; }; - -&i2c2 { - mt9p031@48 { - compatible = "aptina,mt9p031"; - reg = <0x48>; - clocks = <&isp 0>; - vaa-supply = <&vaux4>; - vdd-supply = <&vaux4>; - vdd_io-supply = <&vaux4>; - port { - mt9p031_out: endpoint { - input-clock-frequency = <24000000>; - pixel-clock-frequency = <72000000>; - remote-endpoint = <&ccdc_ep>; - }; - }; - }; -}; - -&i2c3 { - touchscreen: tsc2004@48 { - compatible = "ti,tsc2004"; - reg = <0x48>; - vio-supply = <&vaux1>; - pinctrl-names = "default"; - pinctrl-0 = <&tsc2004_pins>; - interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */ - - touchscreen-fuzz-x = <4>; - touchscreen-fuzz-y = <7>; - touchscreen-fuzz-pressure = <2>; - touchscreen-size-x = <4096>; - touchscreen-size-y = <4096>; - touchscreen-max-pressure = <2048>; - - ti,x-plate-ohms = <280>; - ti,esd-recovery-timeout-ms = <8000>; - }; -}; - -&mcspi1 { - at25@0 { - compatible = "atmel,at25"; - reg = <0>; - spi-max-frequency = <5000000>; - spi-cpha; - spi-cpol; - - pagesize = <64>; - size = <32768>; - address-width = <16>; - }; -}; - -&isp { - pinctrl-names = "default"; - pinctrl-0 = <&isp_pins>; - ports { - port@0 { - reg = <0>; - ccdc_ep: endpoint { - remote-endpoint = <&mt9p031_out>; - bus-width = <8>; - hsync-active = <1>; - vsync-active = <1>; - pclk-sample = <0>; - }; - }; - }; -}; - -&uart1 { - interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>; -}; - -/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */ -&usb_otg_hs { - pinctrl-names = "default"; - pinctrl-0 = <&hsusb_otg_pins>; - interface-type = <0>; - usb-phy = <&usb2_phy>; - phys = <&usb2_phy>; - phy-names = "usb2-phy"; - mode = <3>; - power = <50>; -}; diff --git a/arch/arm/dts/logicpd-torpedo-baseboard.dtsi b/arch/arm/dts/logicpd-torpedo-baseboard.dtsi new file mode 100644 index 0000000000..86c5644f55 --- /dev/null +++ b/arch/arm/dts/logicpd-torpedo-baseboard.dtsi @@ -0,0 +1,395 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/ { + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_key_pins &gpio_key_pins_wkup>; + + sysboot2 { + label = "sysboot2"; + gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; /* gpio2 */ + linux,code = <BTN_0>; + wakeup-source; + }; + + sysboot5 { + label = "sysboot5"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; /* gpio7 */ + linux,code = <BTN_1>; + wakeup-source; + }; + + gpio1 { + label = "gpio1"; + gpios = <&gpio6 21 GPIO_ACTIVE_LOW>; /* gpio181 */ + linux,code = <BTN_2>; + wakeup-source; + }; + + gpio2 { + label = "gpio2"; + gpios = <&gpio6 18 GPIO_ACTIVE_LOW>; /* gpio178 */ + linux,code = <BTN_3>; + wakeup-source; + }; + }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3logic"; + ti,mcbsp = <&mcbsp2>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + + led1 { + label = "led1"; + gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>; /* gpio180 */ + linux,default-trigger = "cpu0"; + }; + + led2 { + label = "led2"; + gpios = <&gpio6 19 GPIO_ACTIVE_HIGH>; /* gpio179 */ + linux,default-trigger = "none"; + }; + }; + + pwm10: dmtimer-pwm { + compatible = "ti,omap-dmtimer-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pins>; + ti,timers = <&timer10>; + #pwm-cells = <3>; + }; + +}; + +&vaux1 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; +}; + +&vaux4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +&mcbsp2 { + status = "okay"; +}; + +&charger { + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */ + 1 0 0x2c000000 0x1000000>; /* CS1: 16MB for LAN9221 */ + + ethernet@gpmc { + pinctrl-names = "default"; + pinctrl-0 = <&lan9221_pins>; + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; /* gpio129 */ + reg = <1 0 0xff>; + }; +}; + +&vpll2 { + regulator-always-on; +}; + +&dss { + status = "ok"; + vdds_dsi-supply = <&vpll2>; + vdda_video-supply = <&video_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins1>; + port { + dpi_out: endpoint { + remote-endpoint = <&lcd_in>; + data-lines = <16>; + }; + }; +}; + +/ { + aliases { + display0 = &lcd0; + }; + + video_reg: video_reg { + pinctrl-names = "default"; + pinctrl-0 = <&panel_pwr_pins>; + compatible = "regulator-fixed"; + regulator-name = "fixed-supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ + }; + + lcd0: display { + compatible = "panel-dpi"; + label = "15"; + status = "okay"; + /* default-on; */ + pinctrl-names = "default"; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <3>; + hback-porch = <2>; + hsync-len = <42>; + vback-porch = <3>; + vfront-porch = <4>; + vsync-len = <11>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + + bl: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&backlight_pins>; + pwms = <&pwm10 0 5000000 0>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <7>; + enable-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; /* gpio_154 */ + }; +}; + +&mmc1 { + interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins &mmc1_cd>; + cd-gpios = <&gpio4 31 GPIO_ACTIVE_LOW>; /* gpio127 */ + vmmc-supply = <&vmmc1>; + bus-width = <4>; + cap-power-off-card; +}; + +&omap3_pmx_core { + gpio_key_pins: pinmux_gpio_key_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_clk.gpio_178 */ + OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_cs0.gpio_181 */ + >; + }; + + pwm_pins: pinmux_pwm_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* gpmc_ncs5.gpt_10_pwm_evt */ + >; + }; + + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d8, PIN_OUTPUT | MUX_MODE4) /* gpio_179 */ + OMAP3_CORE1_IOPAD(0x21da, PIN_OUTPUT | MUX_MODE4) /* gpio_180 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; + + tsc2004_pins: pinmux_tsc2004_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */ + >; + }; + + backlight_pins: pinmux_backlight_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_dx.gpio_154 */ + >; + }; + + isp_pins: pinmux_isp_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE0) /* cam_hs.cam_hs */ + OMAP3_CORE1_IOPAD(0x210e, PIN_INPUT | MUX_MODE0) /* cam_vs.cam_vs */ + OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT | MUX_MODE0) /* cam_xclka.cam_xclka */ + OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT | MUX_MODE0) /* cam_pclk.cam_pclk */ + + OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT | MUX_MODE0) /* cam_d0.cam_d0 */ + OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT | MUX_MODE0) /* cam_d1.cam_d1 */ + OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT | MUX_MODE0) /* cam_d2.cam_d2 */ + OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE0) /* cam_d3.cam_d3 */ + OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT | MUX_MODE0) /* cam_d4.cam_d4 */ + OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT | MUX_MODE0) /* cam_d5.cam_d5 */ + OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0) /* cam_d6.cam_d6 */ + OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0) /* cam_d7.cam_d7 */ + >; + }; + + panel_pwr_pins: pinmux_panel_pwr_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */ + >; + }; + + dss_dpi_pins1: pinmux_dss_dpi_pins1 { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */ + + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */ + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data16.dss_data16 */ + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data17.dss_data17 */ + + OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data18.dss_data0 */ + OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data19.dss_data1 */ + OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data20.dss_data2 */ + OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data21.dss_data3 */ + OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data22.dss_data4 */ + OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data23.dss_data5 */ + >; + }; +}; + +&omap3_pmx_wkup { + gpio_key_pins_wkup: pinmux_gpio_key_pins_wkup { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot0.gpio_2 */ + OMAP3_WKUP_IOPAD(0x2a14, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot5.gpio_7 */ + >; + }; + + lan9221_pins: pinmux_lan9221_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4) /* reserved.gpio_129 */ + >; + }; + + mmc1_cd: pinmux_mmc1_cd { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a54, PIN_INPUT_PULLUP | MUX_MODE4) /* reserved.gpio_127 */ + >; + }; +}; + +&i2c2 { + mt9p031@48 { + compatible = "aptina,mt9p031"; + reg = <0x48>; + clocks = <&isp 0>; + vaa-supply = <&vaux4>; + vdd-supply = <&vaux4>; + vdd_io-supply = <&vaux4>; + port { + mt9p031_out: endpoint { + input-clock-frequency = <24000000>; + pixel-clock-frequency = <72000000>; + remote-endpoint = <&ccdc_ep>; + }; + }; + }; +}; + +&i2c3 { + touchscreen: tsc2004@48 { + compatible = "ti,tsc2004"; + reg = <0x48>; + vio-supply = <&vaux1>; + pinctrl-names = "default"; + pinctrl-0 = <&tsc2004_pins>; + interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; +}; + +&mcspi1 { + at25@0 { + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpha; + spi-cpol; + + pagesize = <64>; + size = <32768>; + address-width = <16>; + }; +}; + +&isp { + pinctrl-names = "default"; + pinctrl-0 = <&isp_pins>; + ports { + port@0 { + reg = <0>; + ccdc_ep: endpoint { + remote-endpoint = <&mt9p031_out>; + bus-width = <8>; + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + }; + }; + }; +}; + +&uart1 { + interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>; +}; + +/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */ +&usb_otg_hs { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb_otg_pins>; + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; diff --git a/arch/arm/dts/logicpd-torpedo-som.dtsi b/arch/arm/dts/logicpd-torpedo-som.dtsi index 23c9228d6a..7d2302e870 100644 --- a/arch/arm/dts/logicpd-torpedo-som.dtsi +++ b/arch/arm/dts/logicpd-torpedo-som.dtsi @@ -7,6 +7,10 @@ #include <dt-bindings/input/input.h> / { + chosen { + stdout-path = &uart1; + }; + cpus { cpu@0 { cpu0-supply = <&vcc>; @@ -27,15 +31,11 @@ }; }; - wl12xx_vmmc: wl12xx_vmmc { - compatible = "regulator-fixed"; - regulator-name = "vwl1271"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - gpio = <&gpio5 29 0>; /* gpio157 */ - startup-delay-us = <70000>; - enable-active-high; - vin-supply = <&vmmc2>; + /* fixed 26MHz oscillator */ + hfclk_26m: oscillator { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <26000000>; }; }; @@ -73,12 +73,17 @@ }; &i2c1 { - clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <2600000>; twl: twl@48 { reg = <0x48>; interrupts = <7>; /* SYS_NIRQ cascaded to intc */ interrupt-parent = <&intc>; + clocks = <&hfclk_26m>; + clock-names = "fck"; + twl_audio: audio { compatible = "ti,twl4030-audio"; codec { @@ -88,56 +93,23 @@ }; &i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; clock-frequency = <400000>; }; &i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; clock-frequency = <400000>; at24@50 { - compatible = "at24,24c02"; + compatible = "atmel,24c64"; readonly; reg = <0x50>; }; }; -/* - * Only found on the wireless SOM. For the SOM without wireless, the pins for - * MMC3 can be routed with jumpers to the second MMC slot on the devkit and - * gpio157 is not connected. So this should be OK to keep common for now, - * probably device tree overlays is the way to go with the various SOM and - * jumpering combinations for the long run. - */ -&mmc3 { - interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>; - pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>; - pinctrl-names = "default"; - vmmc-supply = <&wl12xx_vmmc>; - non-removable; - bus-width = <4>; - cap-power-off-card; - #address-cells = <1>; - #size-cells = <0>; - wlcore: wlcore@2 { - compatible = "ti,wl1283"; - reg = <2>; - interrupt-parent = <&gpio5>; - interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */ - ref-clock-frequency = <26000000>; - tcxo-clock-frequency = <26000000>; - }; -}; - &omap3_pmx_core { - mmc3_pins: pinmux_mm3_pins { - pinctrl-single,pins = < - OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */ - OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */ - OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */ - OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */ - OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ - OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */ - >; - }; mcbsp2_pins: pinmux_mcbsp2_pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */ @@ -180,6 +152,24 @@ OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ >; }; + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ + OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ + >; + }; + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */ + OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */ + >; + }; + i2c3_pins: pinmux_i2c3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */ + OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */ + >; + }; }; &uart2 { @@ -193,15 +183,6 @@ pinctrl-0 = <&mcspi1_pins>; }; -&omap3_pmx_core2 { - mmc3_core2_pins: pinmux_mmc3_core2_pins { - pinctrl-single,pins = < - OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ - OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ - >; - }; -}; - #include "twl4030.dtsi" #include "twl4030_omap3.dtsi" -- 2.17.1

2 1

[U-Boot] [PATCH] ARM: dts: Resync OMAP3 and omap36xx with Linux 4.18-RC4
by Adam Ford 24 Jul '18

24 Jul '18

There have been several minor changes to the OMAP3.dtsi, so this patch re-syncs it with Linux. An addition include/dt-binding was also brought with it. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/arch/arm/dts/omap3.dtsi b/arch/arm/dts/omap3.dtsi index 56c94729bb..4043ecb380 100644 --- a/arch/arm/dts/omap3.dtsi +++ b/arch/arm/dts/omap3.dtsi @@ -215,6 +215,7 @@ #dma-cells = <1>; dma-channels = <32>; dma-requests = <96>; + ti,hwmods = "dma"; }; gpio1: gpio@48310000 { @@ -287,7 +288,6 @@ uart1: serial@4806a000 { compatible = "ti,omap3-uart"; reg = <0x4806a000 0x2000>; - reg-shift = <2>; interrupts-extended = <&intc 72>; dmas = <&sdma 49 &sdma 50>; dma-names = "tx", "rx"; @@ -298,7 +298,6 @@ uart2: serial@4806c000 { compatible = "ti,omap3-uart"; reg = <0x4806c000 0x400>; - reg-shift = <2>; interrupts-extended = <&intc 73>; dmas = <&sdma 51 &sdma 52>; dma-names = "tx", "rx"; @@ -309,7 +308,6 @@ uart3: serial@49020000 { compatible = "ti,omap3-uart"; reg = <0x49020000 0x400>; - reg-shift = <2>; interrupts-extended = <&intc 74>; dmas = <&sdma 53 &sdma 54>; dma-names = "tx", "rx"; @@ -559,6 +557,7 @@ dma-names = "tx", "rx"; clocks = <&mcbsp4_fck>; clock-names = "fck"; + #sound-dai-cells = <0>; status = "disabled"; }; @@ -589,20 +588,6 @@ dma-names = "rx"; }; - smartreflex_core: smartreflex@480cb000 { - compatible = "ti,omap3-smartreflex-core"; - ti,hwmods = "smartreflex_core"; - reg = <0x480cb000 0x400>; - interrupts = <19>; - }; - - smartreflex_mpu_iva: smartreflex@480c9000 { - compatible = "ti,omap3-smartreflex-iva"; - ti,hwmods = "smartreflex_mpu_iva"; - reg = <0x480c9000 0x400>; - interrupts = <18>; - }; - timer1: timer@48318000 { compatible = "ti,omap3430-timer"; reg = <0x48318000 0x400>; @@ -717,6 +702,7 @@ compatible = "ti,ohci-omap3"; reg = <0x48064400 0x400>; interrupts = <76>; + remote-wakeup-connected; }; usbhsehci: ehci@48064800 { diff --git a/arch/arm/dts/omap36xx.dtsi b/arch/arm/dts/omap36xx.dtsi index a0f2d9e805..6fb23ada1f 100644 --- a/arch/arm/dts/omap36xx.dtsi +++ b/arch/arm/dts/omap36xx.dtsi @@ -8,6 +8,7 @@ * kind, whether express or implied. */ +#include <dt-bindings/bus/ti-sysc.h> #include <dt-bindings/media/omap3-isp.h> #include "omap3.dtsi" @@ -34,7 +35,6 @@ uart4: serial@49042000 { compatible = "ti,omap3-uart"; reg = <0x49042000 0x400>; - reg-shift = <2>; interrupts = <80>; dmas = <&sdma 81 &sdma 82>; dma-names = "tx", "rx"; @@ -94,6 +94,51 @@ compatible = "ti,omap36xx-bandgap"; #thermal-sensor-cells = <0>; }; + + target-module@480cb000 { + compatible = "ti,sysc-omap3630-sr", "ti,sysc"; + ti,hwmods = "smartreflex_core"; + reg = <0x480cb038 0x4>; + reg-names = "sysc"; + ti,sysc-mask = <SYSC_OMAP3_SR_ENAWAKEUP>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + clocks = <&sr2_fck>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x480cb000 0x001000>; + + smartreflex_core: smartreflex@0 { + compatible = "ti,omap3-smartreflex-core"; + reg = <0 0x400>; + interrupts = <19>; + }; + }; + + target-module@480c9000 { + compatible = "ti,sysc-omap3630-sr", "ti,sysc"; + ti,hwmods = "smartreflex_mpu_iva"; + reg = <0x480c9038 0x4>; + reg-names = "sysc"; + ti,sysc-mask = <SYSC_OMAP3_SR_ENAWAKEUP>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + clocks = <&sr1_fck>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x480c9000 0x001000>; + + + smartreflex_mpu_iva: smartreflex@480c9000 { + compatible = "ti,omap3-smartreflex-mpu-iva"; + reg = <0 0x400>; + interrupts = <18>; + }; + }; }; thermal_zones: thermal-zones { diff --git a/include/dt-bindings/bus/ti-sysc.h b/include/dt-bindings/bus/ti-sysc.h new file mode 100644 index 0000000000..2c005376ac --- /dev/null +++ b/include/dt-bindings/bus/ti-sysc.h @@ -0,0 +1,22 @@ +/* TI sysc interconnect target module defines */ + +/* Generic sysc found on omap2 and later, also known as type1 */ +#define SYSC_OMAP2_CLOCKACTIVITY (3 << 8) +#define SYSC_OMAP2_EMUFREE (1 << 5) +#define SYSC_OMAP2_ENAWAKEUP (1 << 2) +#define SYSC_OMAP2_SOFTRESET (1 << 1) +#define SYSC_OMAP2_AUTOIDLE (1 << 0) + +/* Generic sysc found on omap4 and later, also known as type2 */ +#define SYSC_OMAP4_DMADISABLE (1 << 16) +#define SYSC_OMAP4_FREEEMU (1 << 1) /* Also known as EMUFREE */ +#define SYSC_OMAP4_SOFTRESET (1 << 0) + +/* SmartReflex sysc found on 36xx and later */ +#define SYSC_OMAP3_SR_ENAWAKEUP (1 << 26) + +/* SYSCONFIG STANDBYMODE/MIDLEMODE/SIDLEMODE supported by hardware */ +#define SYSC_IDLE_FORCE 0 +#define SYSC_IDLE_NO 1 +#define SYSC_IDLE_SMART 2 +#define SYSC_IDLE_SMART_WKUP 3 -- 2.17.1

2 1

[U-Boot] [PATCH] ARM: DTS: Resync am3517-evm.dts with Linux 4.18-rc4
by Adam Ford 24 Jul '18

24 Jul '18

Several changes have been made to the AM3517-evm and the underlying am3517.dtsi file. This patch re-sync's the DTS and DTSI files with Linux. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/arch/arm/dts/am3517-evm.dts b/arch/arm/dts/am3517-evm.dts index 0e4a125f78..98aadb0f81 100644 --- a/arch/arm/dts/am3517-evm.dts +++ b/arch/arm/dts/am3517-evm.dts @@ -8,11 +8,17 @@ /dts-v1/; #include "am3517.dtsi" +#include "am3517-som.dtsi" +#include <dt-bindings/input/input.h> / { model = "TI AM3517 EVM (AM3517/05 TMDSEVM3517)"; compatible = "ti,am3517-evm", "ti,am3517", "ti,omap3"; + aliases { + display0 = &lcd0; + }; + memory@80000000 { device_type = "memory"; reg = <0x80000000 0x10000000>; /* 256 MB */ @@ -24,6 +30,144 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; + + gpio-keys { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + user_pb { + label = "User Push Button"; + linux,code = <BTN_0>; + gpios = <&tca6416 5 GPIO_ACTIVE_LOW>; + }; + + user_sw_1 { + label = "User Switch 1"; + linux,code = <BTN_1>; + gpios = <&tca6416 8 GPIO_ACTIVE_LOW>; + }; + + user_sw_2 { + label = "User Switch 2"; + linux,code = <BTN_2>; + gpios = <&tca6416 9 GPIO_ACTIVE_LOW>; + }; + + user_sw_3 { + label = "User Switch 3"; + linux,code = <BTN_3>; + gpios = <&tca6416 10 GPIO_ACTIVE_LOW>; + }; + + user_sw_4 { + label = "User Switch 4"; + linux,code = <BTN_4>; + gpios = <&tca6416 11 GPIO_ACTIVE_LOW>; + }; + + user_sw_5 { + label = "User Switch 5"; + linux,code = <BTN_5>; + gpios = <&tca6416 12 GPIO_ACTIVE_LOW>; + }; + + user_sw_6 { + label = "User Switch 6"; + linux,code = <BTN_6>; + gpios = <&tca6416 13 GPIO_ACTIVE_LOW>; + }; + + user_sw_7 { + label = "User Switch 7"; + linux,code = <BTN_7>; + gpios = <&tca6416 14 GPIO_ACTIVE_LOW>; + }; + + user_sw_8 { + label = "User Switch 8"; + linux,code = <BTN_8>; + gpios = <&tca6416 15 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&leds_pins>; + + user_led_1 { + label = "am3517evm:green:user_led_1"; + gpios = <&tca6416 7 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + user_led_2 { + label = "am3517evm:green:user_led_2"; + gpios = <&tca6416 6 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + user_led_3 { + label = "am3517evm:green:user_led_3"; + gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; /* SD/MMC card activity */ + }; + + user_led_4 { + label = "am3517evm:green:user_led_4"; + gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + lcd0: display@0 { + compatible = "panel-dpi"; + label = "15"; + status = "okay"; + pinctrl-names = "default"; + enable-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>; /* gpio176, lcd INI */ + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <3>; + hback-porch = <2>; + hsync-len = <42>; + vback-porch = <3>; + vfront-porch = <4>; + vsync-len = <11>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + + bl: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&backlight_pins>; + pwms = <&pwm11 0 5000000 0>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <7>; + enable-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* gpio_182 */ + }; + + pwm11: dmtimer-pwm@11 { + compatible = "ti,omap-dmtimer-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pins>; + ti,timers = <&timer11>; + #pwm-cells = <3>; + }; }; &davinci_emac { @@ -34,12 +178,32 @@ status = "okay"; }; -&i2c1 { - clock-frequency = <400000>; +&dss { + status = "ok"; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins>; + + vdds_dsi-supply = <&vdd_io_reg>; + vdda_video-supply = <&vdd_io_reg>; + + port { + dpi_out: endpoint { + remote-endpoint = <&lcd_in>; + data-lines = <16>; + }; + }; }; &i2c2 { clock-frequency = <400000>; + /* User DIP swithes [1:8] / User LEDS [1:2] */ + tca6416: gpio@21 { + compatible = "ti,tca6416"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + }; }; &i2c3 { @@ -47,8 +211,13 @@ }; &mmc1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; vmmc-supply = <&vmmc_fixed>; bus-width = <4>; + wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>; /* gpio_126 */ + cd-gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio_127 */ }; &mmc2 { @@ -59,3 +228,63 @@ status = "disabled"; }; +&omap3_pmx_core { + + leds_pins: pinmux_leds_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu0.gpio_11 */ + OMAP3_WKUP_IOPAD(0x2a26, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu1.gpio_31 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE4) /* sdmmc1_dat4.gpio_126 */ + OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE4) /* sdmmc1_dat5.gpio_127 */ + >; + }; + + pwm_pins: pinmux_pwm_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21dc, PIN_OUTPUT | MUX_MODE1) /* mcspi2_cs0.gpt11_pwm */ + >; + }; + + backlight_pins: pinmux_backlight_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21de, PIN_OUTPUT | MUX_MODE4) /* mcspi2_cs1.gpio_182 */ + >; + }; + + dss_dpi_pins: pinmux_dss_dpi_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d2, PIN_OUTPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */ + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ + >; + }; +}; diff --git a/arch/arm/dts/am3517-som.dtsi b/arch/arm/dts/am3517-som.dtsi new file mode 100644 index 0000000000..a6d5ff73c1 --- /dev/null +++ b/arch/arm/dts/am3517-som.dtsi @@ -0,0 +1,142 @@ +/* + * Copyright (C) 2016 Derald D. Woods <woods.technical(a)gmail.com> + * + * Based on am3517-evm.dts + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/ { + cpus { + cpu@0 { + cpu0-supply = <&vdd_core_reg>; + }; + }; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */ + + nand@0,0 { + compatible = "ti,omap2-nand"; + linux,mtd-name = "micron,mt29f4g16abchch"; + reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ + nand-bus-width = <16>; + ti,nand-ecc-opt = "bch8"; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-off-ns = <40>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + gpmc,device-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + + s35390a: s35390a@30 { + compatible = "sii,s35390a"; + reg = <0x30>; + + pinctrl-names = "default"; + pinctrl-0 = <&rtc_pins>; + interrupts-extended = <&gpio2 23 IRQ_TYPE_EDGE_FALLING>; /* gpio_55 */ + }; + + tps: tps65023@48 { + compatible = "ti,tps65023"; + reg = <0x48>; + + regulators { + vdd_core_reg: VDCDC1 { + regulator-name = "vdd_core"; + compatible = "regulator-fixed"; + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vdd_io_reg: VDCDC2 { + regulator-name = "vdd_io"; + compatible = "regulator-fixed"; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vdd_1v8_reg: VDCDC3 { + regulator-name = "vdd_1v8"; + compatible = "regulator-fixed"; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vdd_usb18_reg: LDO1 { + regulator-name = "vdd_usb18"; + compatible = "regulator-fixed"; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vdd_usb33_reg: LDO2 { + regulator-name = "vdd_usb33"; + compatible = "regulator-fixed"; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + + touchscreen: tsc2004@4b { + compatible = "ti,tsc2004"; + reg = <0x4b>; + + vio-supply = <&vdd_io_reg>; + + pinctrl-names = "default"; + pinctrl-0 = <&tsc2004_pins>; + interrupts-extended = <&gpio3 1 IRQ_TYPE_EDGE_RISING>; /* gpio_65 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <480>; + touchscreen-size-y = <272>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; +}; + +&omap3_pmx_core { + + rtc_pins: pinmux_rtc_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20b6, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_ncs4.gpio_55 */ + >; + }; + + tsc2004_pins: pinmux_tsc2004_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT | MUX_MODE4) /* gpmc_wait3.gpio_65 */ + >; + }; +}; diff --git a/arch/arm/dts/am3517.dtsi b/arch/arm/dts/am3517.dtsi index ca294914bb..4b6062b631 100644 --- a/arch/arm/dts/am3517.dtsi +++ b/arch/arm/dts/am3517.dtsi @@ -39,6 +39,8 @@ ti,davinci-ctrl-ram-size = <0x2000>; ti,davinci-rmii-en = /bits/ 8 <1>; local-mac-address = [ 00 00 00 00 00 00 ]; + clocks = <&emac_ick>; + clock-names = "ick"; }; davinci_mdio: ethernet@5c030000 { @@ -49,6 +51,8 @@ bus_freq = <1000000>; #address-cells = <1>; #size-cells = <0>; + clocks = <&emac_fck>; + clock-names = "fck"; }; uart4: serial@4809e000 { -- 2.17.1

2 1

[U-Boot] [PATCH] m68k: m5253evbe: Remove this board
by Tom Rini 24 Jul '18

24 Jul '18

The m5253evbe board has been marked as orphan since June of 2014 and should have been dropped a while ago. Do so now. Signed-off-by: Tom Rini <trini(a)konsulko.com> --- arch/m68k/Kconfig | 5 -- board/freescale/m5253evbe/Kconfig | 15 ---- board/freescale/m5253evbe/MAINTAINERS | 6 -- board/freescale/m5253evbe/Makefile | 6 -- board/freescale/m5253evbe/README | 102 --------------------- board/freescale/m5253evbe/m5253evbe.c | 128 -------------------------- configs/M5253EVBE_defconfig | 16 ---- include/configs/M5253EVBE.h | 163 ---------------------------------- 8 files changed, 441 deletions(-) delete mode 100644 board/freescale/m5253evbe/Kconfig delete mode 100644 board/freescale/m5253evbe/MAINTAINERS delete mode 100644 board/freescale/m5253evbe/Makefile delete mode 100644 board/freescale/m5253evbe/README delete mode 100644 board/freescale/m5253evbe/m5253evbe.c delete mode 100644 configs/M5253EVBE_defconfig delete mode 100644 include/configs/M5253EVBE.h diff --git a/arch/m68k/Kconfig b/arch/m68k/Kconfig index 42fb91539af6..1f6df5c87044 100644 --- a/arch/m68k/Kconfig +++ b/arch/m68k/Kconfig @@ -144,10 +144,6 @@ config TARGET_M5253DEMO bool "Support M5253DEMO" select M5253 -config TARGET_M5253EVBE - bool "Support M5253EVBE" - select M5253 - config TARGET_M5272C3 bool "Support M5272C3" select M5272 @@ -214,7 +210,6 @@ source "board/freescale/m52277evb/Kconfig" source "board/freescale/m5235evb/Kconfig" source "board/freescale/m5249evb/Kconfig" source "board/freescale/m5253demo/Kconfig" -source "board/freescale/m5253evbe/Kconfig" source "board/freescale/m5272c3/Kconfig" source "board/freescale/m5275evb/Kconfig" source "board/freescale/m5282evb/Kconfig" diff --git a/board/freescale/m5253evbe/Kconfig b/board/freescale/m5253evbe/Kconfig deleted file mode 100644 index d97b87c4caec..000000000000 --- a/board/freescale/m5253evbe/Kconfig +++ /dev/null @@ -1,15 +0,0 @@ -if TARGET_M5253EVBE - -config SYS_CPU - default "mcf52x2" - -config SYS_BOARD - default "m5253evbe" - -config SYS_VENDOR - default "freescale" - -config SYS_CONFIG_NAME - default "M5253EVBE" - -endif diff --git a/board/freescale/m5253evbe/MAINTAINERS b/board/freescale/m5253evbe/MAINTAINERS deleted file mode 100644 index 74acd1eee504..000000000000 --- a/board/freescale/m5253evbe/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -M5253EVBE BOARD -#M: Hayden Fraser <Hayden.Fraser(a)freescale.com> -S: Orphan (since 2014-06) -F: board/freescale/m5253evbe/ -F: include/configs/M5253EVBE.h -F: configs/M5253EVBE_defconfig diff --git a/board/freescale/m5253evbe/Makefile b/board/freescale/m5253evbe/Makefile deleted file mode 100644 index 79e20b7365b8..000000000000 --- a/board/freescale/m5253evbe/Makefile +++ /dev/null @@ -1,6 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. - -obj-y = m5253evbe.o diff --git a/board/freescale/m5253evbe/README b/board/freescale/m5253evbe/README deleted file mode 100644 index f4eae67fc010..000000000000 --- a/board/freescale/m5253evbe/README +++ /dev/null @@ -1,102 +0,0 @@ -Freescale Amadeus Plus M5253EVBE board -====================================== - -Hayden Fraser(Hayden.Fraser(a)freescale.com) -Created 06/05/2007 -=========================================== - - -1. SWITCH SETTINGS -================== -1.1 N/A - - -2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL -=========================================== -2.1. For the initial bringup, we adopted a consistent memory scheme between U-Boot and - linux kernel, you can customize it based on your system requirements: - SDR: 0x00000000-0x00ffffff - SRAM0: 0x20010000-0x20017fff - SRAM1: 0x20000000-0x2000ffff - MBAR1: 0x10000000-0x4fffffff - MBAR2: 0x80000000-0xCfffffff - Flash: 0xffe00000-0xffffffff - -3. DEFINITIONS AND COMPILATION -============================== -3.1 Explanation on NEW definitions in include/configs/M5253EVBE.h - CONFIG_MCF52x2 Processor family - CONFIG_MCF5253 MCF5253 specific - CONFIG_SYS_CLK Define Amadeus Plus CPU Clock - CONFIG_SYS_MBAR MBAR base address - CONFIG_SYS_MBAR2 MBAR2 base address - -3.2 Compilation - export CROSS_COMPILE=/usr/local/freescale-coldfire-4.1-elf/bin/m68k-elf- - cd u-boot-1-2-x - make distclean - make M5253EVBE_config - make - - -4. SCREEN DUMP -============== -4.1 U-Boot 1.2.0 (Jun 18 2007 - 18:20:00) - -CPU: Freescale Coldfire MCF5253 at 62 MHz -Board: Freescale MCF5253 EVBE -DRAM: 16 MB -FLASH: 2 MB -In: serial -Out: serial -Err: serial -=> flinfo - -Bank # 1: CFI conformant FLASH (16 x 16) Size: 2 MB in 35 Sectors - AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x49 - Erase timeout: 16384 ms, write timeout: 1 ms - - Sector Start Addresses: - FFE00000 RO FFE04000 RO FFE06000 RO FFE08000 RO FFE10000 RO - FFE20000 FFE30000 FFE40000 FFE50000 FFE60000 - FFE70000 FFE80000 FFE90000 FFEA0000 FFEB0000 - FFEC0000 FFED0000 FFEE0000 FFEF0000 FFF00000 - FFF10000 FFF20000 FFF30000 FFF40000 FFF50000 - FFF60000 FFF70000 FFF80000 FFF90000 FFFA0000 - FFFB0000 FFFC0000 FFFD0000 FFFE0000 FFFF0000 - -=> bdinfo -boot_params = 0x00F62F90 -memstart = 0x00000000 -memsize = 0x01000000 -flashstart = 0xFFE00000 -flashsize = 0x00200000 -flashoffset = 0x00000000 -baudrate = 19200 bps - -=> printenv -bootdelay=5 -baudrate=19200 -stdin=serial -stdout=serial -stderr=serial - -Environment size: 134/8188 bytes -=> saveenv -Saving Environment to Flash... -Un-Protected 1 sectors -Erasing Flash... -. done -Erased 1 sectors -Writing to Flash... done -Protected 1 sectors -=> - -5. COMPILER ------------ -To create U-Boot the CodeSourcery's version of the GNU Toolchain for the ColdFire architecture -compiler set (freescale-coldfire-4.1-elf) from www.codesourcery.com was used. -You can download it from:http://www.codesourcery.com/gnu_toolchains/coldfire/download.html - -compiler that you used - for example, codesourcery_elf requires -MQ in rules.mk, old M68K 2.95.3 just -M -codesourcery_elf requires -MQ in rules.mk, old M68K 2.95.3 just -M diff --git a/board/freescale/m5253evbe/m5253evbe.c b/board/freescale/m5253evbe/m5253evbe.c deleted file mode 100644 index 04447faaa4ce..000000000000 --- a/board/freescale/m5253evbe/m5253evbe.c +++ /dev/null @@ -1,128 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2000-2003 - * Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. - * - * Copyright (C) 2004-2007, 2012 Freescale Semiconductor, Inc. - * Hayden Fraser (Hayden.Fraser(a)freescale.com) - */ - -#include <common.h> -#include <asm/immap.h> -#include <asm/io.h> - -DECLARE_GLOBAL_DATA_PTR; - -int checkboard(void) -{ - puts("Board: "); - puts("Freescale MCF5253 EVBE\n"); - return 0; -}; - -int dram_init(void) -{ - /* - * Check to see if the SDRAM has already been initialized - * by a run control tool - */ - if (!(mbar_readLong(MCFSIM_DCR) & 0x8000)) { - u32 RC, dramsize; - - RC = (CONFIG_SYS_CLK / 1000000) >> 1; - RC = (RC * 15) >> 4; - - /* Initialize DRAM Control Register: DCR */ - mbar_writeShort(MCFSIM_DCR, (0x8400 | RC)); - asm("nop"); - - mbar_writeLong(MCFSIM_DACR0, 0x00002320); - asm("nop"); - - /* Initialize DMR0 */ - dramsize = ((CONFIG_SYS_SDRAM_SIZE << 20) - 1) & 0xFFFC0000; - mbar_writeLong(MCFSIM_DMR0, dramsize | 1); - asm("nop"); - - mbar_writeLong(MCFSIM_DACR0, 0x00002328); - asm("nop"); - - /* Write to this block to initiate precharge */ - *(u32 *) (CONFIG_SYS_SDRAM_BASE) = 0xa5a5a5a5; - asm("nop"); - - /* Set RE bit in DACR */ - mbar_writeLong(MCFSIM_DACR0, - mbar_readLong(MCFSIM_DACR0) | 0x8000); - asm("nop"); - - /* Wait for at least 8 auto refresh cycles to occur */ - udelay(500); - - /* Finish the configuration by issuing the MRS */ - mbar_writeLong(MCFSIM_DACR0, - mbar_readLong(MCFSIM_DACR0) | 0x0040); - asm("nop"); - - *(u32 *) (CONFIG_SYS_SDRAM_BASE + 0x800) = 0xa5a5a5a5; - } - - gd->ram_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; - - return 0; -} - -int testdram(void) -{ - /* TODO: XXX XXX XXX */ - printf("DRAM test not implemented!\n"); - - return (0); -} - -#ifdef CONFIG_IDE -#include <ata.h> -int ide_preinit(void) -{ - return (0); -} - -void ide_set_reset(int idereset) -{ - atac_t *ata = (atac_t *) CONFIG_SYS_ATA_BASE_ADDR; - long period; - /* t1, t2, t3, t4, t5, t6, t9, tRD, tA */ - int piotms[5][9] = { {70, 165, 60, 30, 50, 5, 20, 0, 35}, /* PIO 0 */ - {50, 125, 45, 20, 35, 5, 15, 0, 35}, /* PIO 1 */ - {30, 100, 30, 15, 20, 5, 10, 0, 35}, /* PIO 2 */ - {30, 80, 30, 10, 20, 5, 10, 0, 35}, /* PIO 3 */ - {25, 70, 20, 10, 20, 5, 10, 0, 35} /* PIO 4 */ - }; - - if (idereset) { - /* control reset */ - out_8(&ata->cr, 0); - udelay(100); - } else { - mbar2_writeLong(CIM_MISCCR, CIM_MISCCR_CPUEND); - -#define CALC_TIMING(t) (t + period - 1) / period - period = 1000000000 / (CONFIG_SYS_CLK / 2); /* period in ns */ - - /*ata->ton = CALC_TIMING (180); */ - out_8(&ata->t1, CALC_TIMING(piotms[2][0])); - out_8(&ata->t2w, CALC_TIMING(piotms[2][1])); - out_8(&ata->t2r, CALC_TIMING(piotms[2][1])); - out_8(&ata->ta, CALC_TIMING(piotms[2][8])); - out_8(&ata->trd, CALC_TIMING(piotms[2][7])); - out_8(&ata->t4, CALC_TIMING(piotms[2][3])); - out_8(&ata->t9, CALC_TIMING(piotms[2][6])); - - /* IORDY enable */ - out_8(&ata->cr, 0x40); - udelay(2000); - /* IORDY enable */ - setbits_8(&ata->cr, 0x01); - } -} -#endif /* CONFIG_IDE */ diff --git a/configs/M5253EVBE_defconfig b/configs/M5253EVBE_defconfig deleted file mode 100644 index 754787c7d8ea..000000000000 --- a/configs/M5253EVBE_defconfig +++ /dev/null @@ -1,16 +0,0 @@ -CONFIG_M68K=y -CONFIG_SYS_TEXT_BASE=0xFFE00000 -CONFIG_TARGET_M5253EVBE=y -CONFIG_BOOTDELAY=5 -# CONFIG_DISPLAY_BOARDINFO is not set -# CONFIG_CMDLINE_EDITING is not set -# CONFIG_AUTO_COMPLETE is not set -CONFIG_CMD_IMLS=y -CONFIG_CMD_IDE=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_CACHE=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_MAC_PARTITION=y -# CONFIG_NET is not set -CONFIG_MTD_NOR_FLASH=y diff --git a/include/configs/M5253EVBE.h b/include/configs/M5253EVBE.h deleted file mode 100644 index f7bac2bf0e9d..000000000000 --- a/include/configs/M5253EVBE.h +++ /dev/null @@ -1,163 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. - * Hayden Fraser (Hayden.Fraser(a)freescale.com) - */ - -#ifndef _M5253EVBE_H -#define _M5253EVBE_H - -#define CONFIG_MCFTMR - -#define CONFIG_MCFUART -#define CONFIG_SYS_UART_PORT (0) - -#undef CONFIG_WATCHDOG /* disable watchdog */ - - -/* Configuration for environment - * Environment is embedded in u-boot in the second sector of the flash - */ -#ifndef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_ENV_OFFSET 0x4000 -#define CONFIG_ENV_SECT_SIZE 0x2000 -#else -#define CONFIG_ENV_ADDR 0xffe04000 -#define CONFIG_ENV_SECT_SIZE 0x2000 -#endif - -#define LDS_BOARD_TEXT \ - . = DEFINED(env_offset) ? env_offset : .; \ - env/embedded.o(.text) - -/* - * BOOTP options - */ -#undef CONFIG_BOOTP_BOOTFILESIZE - -/* - * Command line configuration. - */ - -/* ATA */ -#define CONFIG_IDE_RESET 1 -#define CONFIG_IDE_PREINIT 1 -#define CONFIG_ATAPI -#undef CONFIG_LBA48 - -#define CONFIG_SYS_IDE_MAXBUS 1 -#define CONFIG_SYS_IDE_MAXDEVICE 2 - -#define CONFIG_SYS_ATA_BASE_ADDR (CONFIG_SYS_MBAR2 + 0x800) -#define CONFIG_SYS_ATA_IDE0_OFFSET 0 - -#define CONFIG_SYS_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */ -#define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 - -#define CONFIG_SYS_MEMTEST_START 0x400 -#define CONFIG_SYS_MEMTEST_END 0x380000 - -#undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ -#define CONFIG_SYS_FAST_CLK -#ifdef CONFIG_SYS_FAST_CLK -# define CONFIG_SYS_PLLCR 0x1243E054 -# define CONFIG_SYS_CLK 140000000 -#else -# define CONFIG_SYS_PLLCR 0x135a4140 -# define CONFIG_SYS_CLK 70000000 -#endif - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ -#define CONFIG_SYS_MBAR2 0x80000000 /* Module Base Addrs 2 */ - -/* - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_SIZE 8 /* SDRAM size in MB */ - -#ifdef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_SYS_MONITOR_BASE 0x20000 -#else -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) -#endif - -#define CONFIG_SYS_MONITOR_LEN 0x40000 -#define CONFIG_SYS_MALLOC_LEN (256 << 10) -#define CONFIG_SYS_BOOTPARAMS_LEN (64*1024) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization ?? - */ -#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) -#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20) - -/* FLASH organization */ -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 35 /* max number of sectors on one chip */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 - -#define CONFIG_SYS_FLASH_CFI 1 -#define CONFIG_FLASH_CFI_DRIVER 1 -#define CONFIG_SYS_FLASH_SIZE 0x200000 -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 16 - -#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 8) -#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 4) -#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) -#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \ - CF_ADDRMASK(2) | \ - CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ - CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ - CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ - CF_CACR_DBWE) - -/* Port configuration */ -#define CONFIG_SYS_FECI2C 0xF0 - -#define CONFIG_SYS_CS0_BASE 0xFFE00000 -#define CONFIG_SYS_CS0_MASK 0x001F0021 -#define CONFIG_SYS_CS0_CTRL 0x00001D80 - -/*----------------------------------------------------------------------- - * Port configuration - */ -#define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ -#define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */ -#define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */ -#define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */ -#define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */ -#define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ -#define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */ - -#endif /* _M5253EVB_H */ -- 2.7.4

1 1