May 2017 - U-Boot

[U-Boot] [PATCH v2 0/5] Add Basic support for RK818
by Jacob Chen 03 May '17

03 May '17

The RK818 chip is a power management IC for multimedia and handheld devices. It contains the following components: - Regulators - RTC - Clkout - battery support This series patch just give it a basic support, to make rk818 board work. Changes in v2: - remove input current selection in probe, it should be configured in board_init_f by manual. - rename rk808 to rk8xx Jacob Chen (5): power: pmic: append rk818 regs to rk808 power: pmic: rk808: add RK818 support power: regulator: rk808: replace vsel_bits with vsel_mask power: regulator: rk808: add rk818 support power: rk808: rename to rk8xx arch/arm/mach-rockchip/rk3288/sdram_rk3288.c | 6 +- configs/chromebit_mickey_defconfig | 4 +- configs/chromebook_jerry_defconfig | 4 +- configs/chromebook_minnie_defconfig | 4 +- configs/fennec-rk3288_defconfig | 4 +- configs/popmetal-rk3288_defconfig | 4 +- configs/sandbox_defconfig | 4 +- configs/sandbox_noblk_defconfig | 4 +- configs/sandbox_spl_defconfig | 4 +- configs/tinker-rk3288_defconfig | 4 +- drivers/power/pmic/Kconfig | 6 +- drivers/power/pmic/Makefile | 2 +- drivers/power/pmic/{rk808.c => rk8xx.c} | 52 +++++--- drivers/power/regulator/Kconfig | 8 +- drivers/power/regulator/Makefile | 2 +- drivers/power/regulator/{rk808.c => rk8xx.c} | 142 +++++++++++++------- include/power/rk808_pmic.h | 77 ----------- include/power/rk8xx_pmic.h | 193 +++++++++++++++++++++++++++ 18 files changed, 354 insertions(+), 170 deletions(-) rename drivers/power/pmic/{rk808.c => rk8xx.c} (59%) rename drivers/power/regulator/{rk808.c => rk8xx.c} (55%) delete mode 100644 include/power/rk808_pmic.h create mode 100644 include/power/rk8xx_pmic.h -- 2.7.4

3 12

[U-Boot] [PATCH v8 0/9] Add mipi dsi display support for rockchip soc.
by Eric Gao 03 May '17

03 May '17

Changes in v8: -Set vop disabled by default. -Move unused config. Changes in v7: -Using IS_ERR_VALUE to check the clk_set_rate' return value. Changes in v6: -Move panel and backlight configuration to it's define node, and set it disbabled defaultly. Changes in v5: -Modify indentation for better readability. -Make all enum variate have explicit value. -Merge Kconfig and Makefile changes into this patch. -Drop previous change, and modify clk_set_rate implement in rk3399. -Regenerate defconfig file using "make savedefconfig" Changes in v4: -Move this patch to an early stage. Changes in v3: -Split GRF changes as a single patch -Split mipi dsi driver file and header as a single patch. -Improve indentation relationship -Add more description in the commit message -Add ret value in debug message. Changes in v2: -Fix rk_display_init() function report error(err:-19). -Add mipi display mode for vop. -Add compatible items for rk3399 vop. -Change the bitwidth for different display mode. -Extend frame buffer size for mipi display -Add pwm0 pinctrl init for lcd backlight. -Add dts config for mipi display. -Add defconfigs for mipi display, so that it can be enabled by default. Eric Gao (9): rockchip: include: grf: Add GRF register declaration for mipi dsi rockchip: video: Add mipi driver support for rockchip soc rockchip: video: vop: Fix rk_display_init() return error rockchip: video: vop: Add mipi display mode for rk3399 rockchip: video: vop: Set different bitwidth for different display mode rockchip: video: vop: Reserve enough space for mipi dispaly rockchip: board: evb_rk3399: initialize pwm0 for dispaly backlight rockchip: dts: Add mipi dsi support for rk3399 rockchip: defconfigs: Add mipi dsi support for rk3399 evb board arch/arm/dts/rk3399-evb.dts | 76 ++++ arch/arm/dts/rk3399.dtsi | 71 +++ arch/arm/include/asm/arch-rockchip/grf_rk3399.h | 29 +- .../include/asm/arch-rockchip/rockchip_mipi_dsi.h | 195 ++++++++ arch/arm/include/asm/arch-rockchip/vop_rk3288.h | 1 + board/rockchip/evb_rk3399/evb-rk3399.c | 7 + configs/evb-rk3399_defconfig | 14 +- drivers/video/rockchip/Kconfig | 9 +- drivers/video/rockchip/Makefile | 1 + drivers/video/rockchip/rk_mipi.c | 491 +++++++++++++++++++++ drivers/video/rockchip/rk_vop.c | 30 +- 11 files changed, 908 insertions(+), 16 deletions(-) create mode 100644 arch/arm/include/asm/arch-rockchip/rockchip_mipi_dsi.h create mode 100644 drivers/video/rockchip/rk_mipi.c -- 1.9.1

2 18

[U-Boot] [PATCH v4 0/4] Add mipi display support for rk3288
by Eric Gao 03 May '17

03 May '17

Changes in v3: -Add Reviewer. -Rebase with local new change. -Add Reviewer. -Add Reviewer. -Add Reviewer. Changes in v2: -Modify some variate's type for compatibility between arm64 and arm32 machine. -Move panel and backlight configuration to it's define node. -Add configs support for rk3288 mipi dsi Changes in v1: -Add grf define for mipi dsi -Make a different configuration for rk3288. -Add dts configuration. Eric Gao (4): rockchip: rk3288: grf: Add grf define for mipi dsi rockchip: video: Add mipi display support for rk3288 rockchip: dts: evb_rk3288: Add mipi display support rockchip: configs: Add config support for rk3288 mipi dsi arch/arm/dts/rk3288-evb.dtsi | 80 +++++++++++++++++++++++++ arch/arm/dts/rk3288.dtsi | 41 +++++++++++++ arch/arm/include/asm/arch-rockchip/grf_rk3288.h | 62 +++++++++++++++++++ configs/evb-rk3288_defconfig | 6 +- drivers/video/rockchip/rk_mipi.c | 72 +++++++++++++++++----- 5 files changed, 244 insertions(+), 17 deletions(-) -- 1.9.1

2 6

Re: [U-Boot] [PATCH 0/20] tegra: Expand Nyan-big support
by Matthew Gorski 03 May '17

03 May '17

Let me repost this to the bottom. New to the mailing list ;) I am using chained boot to test uboot as a FIT image so I I don't have to flash to spl flash. Does CONFIG_SPL_TEXT_BASE need to be adjusted for chained boot? I am using instructions to boot Linux for Tegra from sdcard/USB in developer mode. I can boot L4T fine with kernel v3.10. What mainline branch should I try? On May 1, 2017 12:11 PM, "Matthew Gorski" <matt.gorski(a)gmail.com> wrote: On May 1, 2017 11:45 AM, "Simon Glass" <sjg(a)chromium.org> wrote: Hi Matthew, On 1 May 2017 at 09:37, Matthew Gorski <matt.gorski(a)gmail.com> wrote: > Thanks for the reply Simon. > > I have been trying to find the System.map for depthcharge to see the kernel > load address but I am unable to find anything. I have tried multiple > CONFIG_SYS_TEXT_BASE settings with no luck. How did you choose what to use? Also note that Tegra uses SPL to start, so you may need to adjust CONFIG_SPL_TEXT_BASE instead. > > I am creating my sdcard with a standard linux (Linux for Tegra) rootfs: Did these instructions come from a web site somewhere? > > Partition an SD card > > sudo cgpt create <MMC BLOCK DEVICE> > sudo cgpt add -b 34 -s 32768 -P 1 -S 1 -t kernel <MMC BLOCK DEVICE> # 16 MB > kernel image partition > sudo cgpt add -b 32802 -s <ROOT PARTITION SIZE in 512B sectors> -t rootfs > <MMC BLOCK DEVICE> > > cgpt doesn't seem to create a protective MBR. If one is not already in > place, it can be created with: > > sudo gdisk <MMC BLOCK DEVICE> # and enter command w > > Copy data to the SD card > > sudo dd if=./kernelpart.bin of=<MMC BLOCK DEVICE>p1 > sudo mkfs.ext4 <MMC BLOCK DEVICE>p2 > sudo mount <MMC BLOCK DEVICE>p2 /mnt/ > How are you actually making it boot? Is this in dev mode with USB boot enabled and pressing Ctrl-U? Also, as this is a mailing list, please avoid top-posting. - Simon I am using chained boot to test uboot as a FIT image so I I don't have to flash to spl flash. Does CONFIG_SPL_TEXT_BASE need to be adjusted for chained boot? I am using instructions to boot Linux for Tegra from sdcard/USB in developer mode. I can boot L4T fine with kernel v3.10. What mainline branch should I try? > > On Mon, May 1, 2017 at 11:14 AM, Simon Glass <sjg(a)chromium.org> wrote: >> >> Hi Matthew, >> >> On 1 May 2017 at 08:43, Matthew Gorski <matt.gorski(a)gmail.com> wrote: >> > I am porting u-boot to nyan_big and need some input. I have been >> > searching >> > high and low and found this thread here: [U-Boot] [PATCH 0/20] tegra: >> > Expand >> > Nyan-big support >> > >> > https://lists.denx.de/pipermail/u-boot/2015-March/209530.html >> > >> > I have tried to build u-boot with the branch here: >> > >> > https://git.collabora.com/cgit/user/tomeu/u-boot.git/commit/?h=nyan-big >> > >> > and also the official chromium next branch >> >> Have you tried mainline U-Boot? It already supports nyan-big. I'm not >> sure about the situation with the downstream trees. >> >> > >> > I followed building instructions here: >> > >> > https://www.chromium.org/chromium-os/firmware-porting-guide/ using-nv-u-boot-on-the-samsung-arm-chromebook >> > >> > I build with these commands: >> > >> > mkimage -e 0x81000100 -a 0x81000100 -f kernel-big.its kernel-u-boot >> > >> > (with and without the load address setting) >> > >> > vbutil_kernel --arch arm --pack kernel.bin --keyblock >> > /usr/share/vboot/devkeys/kernel.keyblock --signprivate >> > /usr/share/vboot/devkeys/kernel_data_key.vbprivk --version 1 --config >> > dummy.txt --vmlinuz kernel-u-boot --bootloader dummy.txt >> > >> > I have had numerous failed attempts to boot uboot from sdcard mmcblk1p1 >> > >> > Any help is appreciated I have only gotten a blank screen after weeks of >> > flashing. I can boot custom v3.10 kernels so I assume I am using the >> > correct building procedure. Thanks in advance for help from the u-boot >> > community. >> >> It is possible that it needs a particular address due to limitations >> in the FIT support on Nyan. I'm not sure what it is but might be able >> to take a look at some point. >> >> How are you building your SD card? Are you following some instructions >> from somewhere? >> >> Regards, >> Simon > >

4 18

[U-Boot] [PATCH v3 0/4] Add mipi display support for rk3288
by Eric Gao 03 May '17

03 May '17

Changes in v3: -Add Reviewer. -Add Reviewer. -Add Reviewer. -Add Reviewer. Changes in v2: -Modify some variate's type for compatibility between arm64 and arm32 machine. -Move panel and backlight configuration to it's define node. -Add configs support for rk3288 mipi dsi Changes in v1: -Add grf define for mipi dsi -Make a different configuration for rk3288. -Add dts configuration. Eric Gao (4): rockchip: rk3288: grf: Add grf define for mipi dsi rockchip: video: Add mipi display support for rk3288 rockchip: dts: evb_rk3288: Add mipi display support rockchip: configs: Add config support for rk3288 mipi dsi arch/arm/dts/rk3288-evb.dtsi | 80 +++++++++++++++++++++++++ arch/arm/dts/rk3288.dtsi | 41 +++++++++++++ arch/arm/include/asm/arch-rockchip/grf_rk3288.h | 62 +++++++++++++++++++ configs/evb-rk3288_defconfig | 6 +- drivers/video/rockchip/rk_mipi.c | 68 +++++++++++++++++---- 5 files changed, 242 insertions(+), 15 deletions(-) -- 1.9.1

2 5

[U-Boot] saveenv not working (u-boot-2017.05-rc3)
by Teoh Choon Zone 03 May '17

03 May '17

I'm using Cypress S25FL512S QSPI, but "saveenv" is not working in u-boot-2017.05-rc3, the changes did not get stored even though the following message is printed: Saving Environment to SPI Flash... SF: Detected s25fl512s_256k with page size 512 Bytes, erase size 256 KiB, total 64 MiB Erasing SPI flash...Writing to SPI flash...done Below is my DTS content: &qspi { status = "okay"; u-boot,dm-pre-reloc; flash0: s25fl512s@0 { u-boot,dm-pre-reloc; #address-cells = <1>; #size-cells = <1>; compatible = "spansion,s25fl512s", "jedec,spi-nor"; reg = <0>; spi-max-frequency = <66000000>; spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; spi-cpol; spi-cpha; m25p,fast-read; cdns,page-size = <512>; cdns,block-size = <262144>; cdns,tshsl-ns = <50>; cdns,tsd2d-ns = <50>; cdns,tchsh-ns = <3>; cdns,tslch-ns = <3>; partition@qspi-boot { /* 1536kB for u-boot */ label = "Flash 0 u-boot"; reg = <0x0 0x180000>; }; partition@qspi-env { /* 256kB for u-boot env */ label = "Flash 0 u-boot env"; reg = <0x180000 0x40000>; }; partition@qspi-kernel { /* 8MB for kernel */ label = "Flash 0 kernel"; reg = <0x1C0000 0x800000>; }; partition@qspi-dtb { /* 256kB for dtb */ label = "Flash 0 dtb"; reg = <0x9C0000 0x40000>; }; partition@qspi-rootfs { /* 54MB for UBIFS */ label = "Flash 0 UBIFS Filesystem"; reg = <0xA00000 0x3600000>; }; }; }; Below is the snippet of my board include header: #define CONFIG_ENV_IS_IN_SPI_FLASH /* * U-Boot environment */ #define CONFIG_ENV_SIZE (2 * 1024) /* Environment for SDMMC boot */ #if defined(CONFIG_ENV_IS_IN_MMC) && !defined(CONFIG_ENV_OFFSET) #define CONFIG_SYS_MMC_ENV_DEV 0 /* device 0 */ #define CONFIG_ENV_OFFSET 512 /* just after the MBR */ #endif /* Environment for QSPI boot */ #define CONFIG_ENV_OFFSET 0x00180000 #define CONFIG_ENV_SECT_SIZE (256 * 1024) /* * mtd partitioning for serial NOR flash * * device nor0 <ff705000.spi.0>, # parts = 5 * #: name size offset mask_flags * 0: u-boot 0x00180000 0x00000000 0 * 1: env 0x00040000 0x00180000 0 * 2: kernel 0x00800000 0x001c0000 0 * 3: dtb 0x00040000 0x009c0000 0 * 4: rootfs 0x03600000 0x00a00000 0 * */ #if defined(CONFIG_CMD_SF) && !defined(MTDPARTS_DEFAULT) #define MTDPARTS_DEFAULT "mtdparts=ff705000.spi.0:"\ "1536k(u-boot)," \ "256k(env)," \ "8m(kernel)," \ "256k(dtb)," \ "-@54m(rootfs)\0" #endif

1 0

[U-Boot] [PATCH v2 0/3] spl: dfu: misc fixes and reduce MLO foot print
by Ravi Babu 02 May '17

02 May '17

The patch series spl-dfu fixes includes - select spl-dfu only spl-ram supported - ignore the dfu-reset for spl-dfu - reduce the spl-dfu MLO foot print buildman ran for arm targets Change history: v1: - Kconfig fix for dfu-reset for SPL-DFU - compile out CONFIG_DFU_MMC for SPL-DFU Ravi Babu (3): spl: Kconfig: dfu: spl-dfu depends on SPL_RAM_SUPPORT common: dfu: ignore reset for spl-dfu spl: dfu: reduce spl-dfu MLO size common/Makefile | 3 +-- common/dfu.c | 2 +- common/spl/Kconfig | 5 +++++ drivers/dfu/Makefile | 2 ++ drivers/dfu/dfu.c | 4 ++++ include/dfu.h | 2 +- 6 files changed, 14 insertions(+), 4 deletions(-) -- 1.9.1

3 15

[U-Boot] [PATCH v3 1/2] i2c_eeprom: add read and write functions
by Jonas Karlman 02 May '17

02 May '17

Signed-off-by: Jonas Karlman <jonas(a)kwiboo.se> --- Changes in v3: - Add i2c_eeprom_{read,write} functions Changes in v2: None drivers/misc/i2c_eeprom.c | 32 ++++++++++++++++++++++++++------ include/i2c_eeprom.h | 24 ++++++++++++++++++++++++ 2 files changed, 50 insertions(+), 6 deletions(-) diff --git a/drivers/misc/i2c_eeprom.c b/drivers/misc/i2c_eeprom.c index c9f4174bad..da6e2b05f7 100644 --- a/drivers/misc/i2c_eeprom.c +++ b/drivers/misc/i2c_eeprom.c @@ -10,21 +10,41 @@ #include <i2c.h> #include <i2c_eeprom.h> -static int i2c_eeprom_read(struct udevice *dev, int offset, uint8_t *buf, - int size) +int i2c_eeprom_read(struct udevice *dev, int offset, uint8_t *buf, int size) +{ + const struct i2c_eeprom_ops *ops = device_get_ops(dev); + + if (!ops->read) + return -ENOSYS; + + return ops->read(dev, offset, buf, size); +} + +int i2c_eeprom_write(struct udevice *dev, int offset, uint8_t *buf, int size) +{ + const struct i2c_eeprom_ops *ops = device_get_ops(dev); + + if (!ops->write) + return -ENOSYS; + + return ops->write(dev, offset, buf, size); +} + +static int i2c_eeprom_std_read(struct udevice *dev, int offset, uint8_t *buf, + int size) { return dm_i2c_read(dev, offset, buf, size); } -static int i2c_eeprom_write(struct udevice *dev, int offset, - const uint8_t *buf, int size) +static int i2c_eeprom_std_write(struct udevice *dev, int offset, + const uint8_t *buf, int size) { return -ENODEV; } struct i2c_eeprom_ops i2c_eeprom_std_ops = { - .read = i2c_eeprom_read, - .write = i2c_eeprom_write, + .read = i2c_eeprom_std_read, + .write = i2c_eeprom_std_write, }; static int i2c_eeprom_std_ofdata_to_platdata(struct udevice *dev) diff --git a/include/i2c_eeprom.h b/include/i2c_eeprom.h index 0452892812..bb5c6b118b 100644 --- a/include/i2c_eeprom.h +++ b/include/i2c_eeprom.h @@ -20,4 +20,28 @@ struct i2c_eeprom { unsigned pagewidth; }; +/* + * i2c_eeprom_read() - read bytes from an I2C EEPROM chip + * + * @dev: Chip to read from + * @offset: Offset within chip to start reading + * @buf: Place to put data + * @size: Number of bytes to read + * + * @return 0 on success, -ve on failure + */ +int i2c_eeprom_read(struct udevice *dev, int offset, uint8_t *buf, int size); + +/* + * i2c_eeprom_write() - write bytes to an I2C EEPROM chip + * + * @dev: Chip to write to + * @offset: Offset within chip to start writing + * @buf: Buffer containing data to write + * @size: Number of bytes to write + * + * @return 0 on success, -ve on failure + */ +int i2c_eeprom_write(struct udevice *dev, int offset, uint8_t *buf, int size); + #endif -- 2.11.0

3 2

[U-Boot] [PATCH v3 2/2] rockchip: tinker: set ethaddr in late init
by Jonas Karlman 02 May '17

02 May '17

Set ethernet mac address in late init for Tinker Board, prevents getting a random mac address each boot. Read mac address from eeprom, first 6 bytes from m24c08@50. Same as /etc/init.d/rockchip.sh on Tinker OS. Signed-off-by: Jonas Karlman <jonas(a)kwiboo.se> --- Changes in v3: - Use uclass_first_device_err() to find eeprom - Use i2c_eeprom_read() to read eeprom Changes in v2: - Change to use i2c_eeprom device driver arch/arm/dts/rk3288-tinker.dts | 7 +++++++ board/rockchip/tinker_rk3288/tinker-rk3288.c | 28 ++++++++++++++++++++++++++++ configs/tinker-rk3288_defconfig | 3 +++ 3 files changed, 38 insertions(+) diff --git a/arch/arm/dts/rk3288-tinker.dts b/arch/arm/dts/rk3288-tinker.dts index 22881cb785..ea2f715922 100644 --- a/arch/arm/dts/rk3288-tinker.dts +++ b/arch/arm/dts/rk3288-tinker.dts @@ -67,3 +67,10 @@ &gpio8 { u-boot,dm-pre-reloc; }; + +&i2c2 { + m24c08@50 { + compatible = "at,24c08", "i2c-eeprom"; + reg = <0x50>; + }; +}; diff --git a/board/rockchip/tinker_rk3288/tinker-rk3288.c b/board/rockchip/tinker_rk3288/tinker-rk3288.c index 79541a3939..c2872e7330 100644 --- a/board/rockchip/tinker_rk3288/tinker-rk3288.c +++ b/board/rockchip/tinker_rk3288/tinker-rk3288.c @@ -5,3 +5,31 @@ */ #include <common.h> +#include <dm.h> +#include <i2c_eeprom.h> +#include <netdev.h> + +static int get_ethaddr_from_eeprom(u8 *addr) +{ + int ret; + struct udevice *dev; + + ret = uclass_first_device_err(UCLASS_I2C_EEPROM, &dev); + if (ret) + return ret; + + return i2c_eeprom_read(dev, 0, addr, 6); +} + +int rk_board_late_init(void) +{ + u8 ethaddr[6]; + + if (get_ethaddr_from_eeprom(ethaddr)) + return 0; + + if (is_valid_ethaddr(ethaddr)) + eth_setenv_enetaddr("ethaddr", ethaddr); + + return 0; +} diff --git a/configs/tinker-rk3288_defconfig b/configs/tinker-rk3288_defconfig index cec39384b3..dc3699d5c4 100644 --- a/configs/tinker-rk3288_defconfig +++ b/configs/tinker-rk3288_defconfig @@ -11,6 +11,7 @@ CONFIG_CONSOLE_MUX=y # CONFIG_DISPLAY_CPUINFO is not set CONFIG_SPL_STACK_R=y CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x2000 +CONFIG_SPL_I2C_SUPPORT=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y @@ -39,6 +40,8 @@ CONFIG_CLK=y CONFIG_SPL_CLK=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_I2C_EEPROM=y CONFIG_MMC_DW=y CONFIG_MMC_DW_ROCKCHIP=y CONFIG_DM_ETH=y -- 2.11.0

3 2

[U-Boot] [PATCH 00/19] fdt: Move to the new upstream pylibfdt library
by Simon Glass 02 May '17

02 May '17

Python libfdt bindings have recently been accepted upstream. While the internals have changed a fair bit most of the API remains the same. Still, a few functions are different from how they are used in U-Boot so changes are needed to make this work. At present in U-Boot there are two libraries for accessing a device tree file: - FdtNormal which uses U-Boot's own Python bindings - FdtFallback which uses the fdtget command-line utility The latter is not a great solution: it is fairly slow since the DT is re-read for every access and it cannot provide DT offsets or packing of the DT. In addition, U-Boot now builds the libfdt module if swig is available, meaning that the fallback module is not used in that case. Finally, at some point in the future distributions may start packaging the libfdt Python module and it will be available without U-Boot needing to build it itself. Therefore it seems like a good idea to take this opportunity to drop the fallback module and just require that the Python libfdt bindings be present (at least if need by the build). The bindings are needed in two situations: - When dtoc is used to convert a device tree into C code. This is enabled by CONFIG_SPL_OF_PLATDATA - When binman is used to produce a firmware image. This is used on all x86 and sunxi boards at present This series: - Plumbs in building the Python libfdt module to the U-Boot build system - Ensures that the module is always built if needed, print an error if swig is not available (and thus the module cannot be built) - Allows use of a libfdt.py module already installed on the machine - Drops the FdtFallback support - Moves fdt.h and libfdt.h into lib/libfdt to aid with syncing with upstream, building the Python bindings and to keep the code together - Merges Fdt and FdtNormal to simplify the code - Adjusts the Fdt library to work with the new libfdt module - Adds a few more tests to check access to properties in the DT - Adjusts binman and dtoc to work with the new approach It should be possible to easily sync libfdt's Python bindings with U-Boot in the future, as development there proceeds. Simon Glass (19): pci: Correct cast for sandbox fdt: Correct cast for sandbox in fdtdec_setup_memory_size() fdt: Use SPDX format for licenses in the libfdt headers fdt: Move header files into lib/libfdt fdt: Allow swig options to be provided by Makefile fdt: Add all source files to the libfdt build fdt: Rename existing python libfdt module fdt: Build the new python libfdt module fdt: Update fdt_test to use 'dt' instead of 'fdt' fdt: dtoc: Add a full set of property tests fdt: Support use of the new python libfdt library fdt: Makefile: Build python libfdt library if needed fdt: Stop building the old python libfdt module fdt: Drop use of the legacy libfdt python module fdt: Drop fdt_fallback library binman: Drop a special case related to fdt_fallback fdt: Merge fdt_normal with its base class binman: Rename fdt variable to dtb fdt: Drop fdt_select.py Makefile | 16 +- cmd/pci.c | 3 +- include/fdt.h | 112 +- include/libfdt.h | 2138 +------------------------- lib/fdtdec.c | 3 +- lib/libfdt/fdt.h | 67 + lib/libfdt/libfdt.h | 2144 +++++++++++++++++++++++++++ lib/libfdt/libfdt.swig | 113 -- lib/libfdt/pylibfdt/setup.py | 4 +- lib/libfdt/setup.py | 38 - scripts/Makefile.spl | 17 +- tools/Makefile | 43 +- tools/binman/binman.py | 3 + tools/binman/control.py | 12 +- tools/binman/etype/u_boot_dtb_with_ucode.py | 24 +- tools/binman/fdt_test.py | 64 +- tools/binman/func_test.py | 48 +- tools/binman/test/45_prop_test.dts | 23 + tools/dtoc/dtoc.py | 3 +- tools/dtoc/fdt.py | 183 ++- tools/dtoc/fdt_fallback.py | 181 --- tools/dtoc/fdt_normal.py | 225 --- tools/dtoc/fdt_select.py | 36 - 23 files changed, 2539 insertions(+), 2961 deletions(-) create mode 100644 lib/libfdt/fdt.h create mode 100644 lib/libfdt/libfdt.h delete mode 100644 lib/libfdt/libfdt.swig delete mode 100644 lib/libfdt/setup.py create mode 100644 tools/binman/test/45_prop_test.dts delete mode 100644 tools/dtoc/fdt_fallback.py delete mode 100644 tools/dtoc/fdt_normal.py delete mode 100644 tools/dtoc/fdt_select.py -- 2.12.2.762.g0e3151a226-goog

4 49