December 2017 - U-Boot

[U-Boot] [PATCH 0/9] LS1012A PFE driver patch series
by Calvin Johnson 26 Jan '18

26 Jan '18

Hi, This patch series introduces U-Boot support for NXP's LS1012A Packet Forwarding Engine (pfe_eth). LS1012A uses hardware packet forwarding engine to provide high performance Ethernet interfaces. The device includes two Ethernet ports. Depends on https://patchwork.ozlabs.org/patch/704305 Regards Calvin Calvin Johnson (9): drivers: net: pfe_eth: LS1012A PFE driver introduction drivers: net: pfe_eth: provide pfe commands drivers: net: pfe_eth: LS1012A PFE headers board: freescale: ls1012a: enable network support on ls1012a platforms armv8: fsl-lsch2: initialize pfe gemac armv8: fsl-lsch2: add pfe macros and update ccsr_scfg structure armv8: fsl-lsch2: configure pfe's scfg & dcfg registers fsl: csu: enable ns access for PFE configs: ls1012a: add pfe configuration for LS1012A arch/arm/cpu/armv8/fsl-layerscape/cpu.c | 8 + arch/arm/cpu/armv8/fsl-layerscape/soc.c | 18 + .../include/asm/arch-fsl-layerscape/immap_lsch2.h | 38 +- .../include/asm/arch-fsl-layerscape/ns_access.h | 2 + arch/arm/include/asm/arch-fsl-layerscape/soc.h | 3 + board/freescale/ls1012afrdm/Makefile | 1 + board/freescale/ls1012afrdm/eth.c | 86 ++ board/freescale/ls1012afrdm/ls1012afrdm.c | 5 - board/freescale/ls1012aqds/Makefile | 1 + board/freescale/ls1012aqds/eth.c | 263 +++++ board/freescale/ls1012aqds/ls1012aqds.c | 97 +- board/freescale/ls1012aqds/ls1012aqds_pfe.h | 48 + board/freescale/ls1012aqds/ls1012aqds_qixis.h | 2 +- board/freescale/ls1012ardb/Makefile | 1 + board/freescale/ls1012ardb/eth.c | 70 ++ board/freescale/ls1012ardb/ls1012ardb.c | 4 - configs/ls1012afrdm_qspi_defconfig | 1 + configs/ls1012aqds_qspi_defconfig | 1 + configs/ls1012ardb_qspi_defconfig | 1 + drivers/net/Kconfig | 1 + drivers/net/Makefile | 1 + drivers/net/pfe_eth/Kconfig | 29 + drivers/net/pfe_eth/Makefile | 11 + drivers/net/pfe_eth/pfe.c | 1161 ++++++++++++++++++++ drivers/net/pfe_eth/pfe_cmd.c | 537 +++++++++ drivers/net/pfe_eth/pfe_driver.c | 626 +++++++++++ drivers/net/pfe_eth/pfe_eth.c | 545 +++++++++ drivers/net/pfe_eth/pfe_firmware.c | 230 ++++ include/configs/ls1012a_common.h | 6 +- include/configs/ls1012afrdm.h | 7 + include/configs/ls1012aqds.h | 14 + include/configs/ls1012ardb.h | 13 + include/pfe_eth/pfe/cbus.h | 75 ++ include/pfe_eth/pfe/cbus/bmu.h | 40 + include/pfe_eth/pfe/cbus/class_csr.h | 181 +++ include/pfe_eth/pfe/cbus/emac.h | 150 +++ include/pfe_eth/pfe/cbus/gpi.h | 62 ++ include/pfe_eth/pfe/cbus/hif.h | 68 ++ include/pfe_eth/pfe/cbus/hif_nocpy.h | 40 + include/pfe_eth/pfe/cbus/tmu_csr.h | 148 +++ include/pfe_eth/pfe/cbus/util_csr.h | 47 + include/pfe_eth/pfe/pfe.h | 178 +++ include/pfe_eth/pfe_driver.h | 55 + include/pfe_eth/pfe_eth.h | 111 ++ include/pfe_eth/pfe_firmware.h | 17 + 45 files changed, 4983 insertions(+), 20 deletions(-) create mode 100644 board/freescale/ls1012afrdm/eth.c create mode 100644 board/freescale/ls1012aqds/eth.c create mode 100644 board/freescale/ls1012aqds/ls1012aqds_pfe.h create mode 100644 board/freescale/ls1012ardb/eth.c create mode 100644 drivers/net/pfe_eth/Kconfig create mode 100644 drivers/net/pfe_eth/Makefile create mode 100644 drivers/net/pfe_eth/pfe.c create mode 100644 drivers/net/pfe_eth/pfe_cmd.c create mode 100644 drivers/net/pfe_eth/pfe_driver.c create mode 100644 drivers/net/pfe_eth/pfe_eth.c create mode 100644 drivers/net/pfe_eth/pfe_firmware.c create mode 100644 include/pfe_eth/pfe/cbus.h create mode 100644 include/pfe_eth/pfe/cbus/bmu.h create mode 100644 include/pfe_eth/pfe/cbus/class_csr.h create mode 100644 include/pfe_eth/pfe/cbus/emac.h create mode 100644 include/pfe_eth/pfe/cbus/gpi.h create mode 100644 include/pfe_eth/pfe/cbus/hif.h create mode 100644 include/pfe_eth/pfe/cbus/hif_nocpy.h create mode 100644 include/pfe_eth/pfe/cbus/tmu_csr.h create mode 100644 include/pfe_eth/pfe/cbus/util_csr.h create mode 100644 include/pfe_eth/pfe/pfe.h create mode 100644 include/pfe_eth/pfe_driver.h create mode 100644 include/pfe_eth/pfe_eth.h create mode 100644 include/pfe_eth/pfe_firmware.h -- 2.7.4

5 20

[U-Boot] [PATCH] common/memsize.c: restore content of the base address
by Patrick Delaunay 25 Jan '18

25 Jan '18

In function get_ram_size() and for 2 last cases the content of the base address (*base) is not restored even it is correctly saved in stack (in save[i]). This patch solved this issue. The content of the base address is saved in new variable in stack (save_base) to avoid the need of other information (value of i) and restored in all the cases. Signed-off-by: Patrick Delaunay <patrick.delaunay(a)st.com> Reviewed-by: CITOOLS <smet-aci-reviews(a)lists.codex.cro.st.com> Reviewed-by: CIBUILD <smet-aci-builds(a)lists.codex.cro.st.com> --- issue detected on my custom board with - base = 0xC0000000 - size = maxsize = 0x4000000 The loop is completely executed and the size is correctly detected, but content in 0xC0000000 is not restored So I have 0xC0000000 = 0x0 at the end of the function. That cause issue in my use-case because U-Boot in loaded at 0xC1000000 and some information can be saved by ATF in DDR at 0xC0000000 address. And the content of DDR is modified by this function. common/memsize.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/common/memsize.c b/common/memsize.c index 0fb9ba5..d632293 100644 --- a/common/memsize.c +++ b/common/memsize.c @@ -27,7 +27,8 @@ DECLARE_GLOBAL_DATA_PTR; long get_ram_size(long *base, long maxsize) { volatile long *addr; - long save[32]; + long save[31]; + long save_base; long cnt; long val; long size; @@ -43,7 +44,7 @@ long get_ram_size(long *base, long maxsize) addr = base; sync(); - save[i] = *addr; + save_base = *addr; sync(); *addr = 0; @@ -51,7 +52,7 @@ long get_ram_size(long *base, long maxsize) if ((val = *addr) != 0) { /* Restore the original data before leaving the function. */ sync(); - *addr = save[i]; + *base = save_base; for (cnt = 1; cnt < maxsize / sizeof(long); cnt <<= 1) { addr = base + cnt; sync(); @@ -76,9 +77,11 @@ long get_ram_size(long *base, long maxsize) addr = base + cnt; *addr = save[--i]; } + *base = save_base; return (size); } } + *base = save_base; return (maxsize); } -- 2.7.4

3 10

[U-Boot] btrfs: data abort with lzo compression (armv7/am335x)
by Robert Nelson 25 Jan '18

25 Jan '18

Hi Marek, Having btrfs support in u-boot is awesome! With u-boot v2018.01-rc1 on our arm target (am335x) BeagleBone family, we are seeing a data abort with lzo compression. I'm wondering if you've seen something similar with your systems: ignore the "Failed to mount ext2 filesystem..." as we are using the genric "load" and extX support is built-in too.. loading /boot/vmlinuz-4.9.68-ti-r83 ... Failed to mount ext2 filesystem... data abort pc : [<9ff6eab8>] lr : [<00000000>] reloc pc : [<80825ab8>] lr : [<e08b7000>] sp : 9df28148 ip : 82020000 fp : 0001f000 r10: 00000d52 r9 : 9df28ed8 r8 : 82001000 r7 : 0001d12c r6 : 00001000 r5 : 0001d2a6 r4 : 9df53fe2 r3 : 00001000 r2 : 82000000 r1 : 00001000 r0 : 00000000 Flags: nzCv IRQs off FIQs on Mode SVC_32 Resetting CPU ... resetting ... the other two options; no compress and zlib are working great in our single partition setup! Regards, -- Robert Nelson https://rcn-ee.com/

3 3

[U-Boot] [PATCH v6 0/2] Generic firmware loader
by tien.fong.chee＠intel.com 24 Jan '18

24 Jan '18

From: Tien Fong Chee <tien.fong.chee(a)intel.com> This patchset contains generic firmware loader which is very close to Linux firmware loader but for U-Boot framework. Generic firmware loader can be used load whatever into target location, and then consumer driver would use it to program whatever, ie. the FPGA. This version mainly resolved comments from Lothar Waßmann in [v5]. This series is working on top of u-boot.git - http://git.denx.de/u-boot.git . [v5]: https://www.mail-archive.com/u-boot@lists.denx.de/msg272771.html v5 -> v6 changes: ----------------- - Return error code when fs_read is fail. - Return actual read size when fs_read is success. Patchset history ---------------- [v1]: https://www.mail-archive.com/u-boot@lists.denx.de/msg271905.html [v2]: https://www.mail-archive.com/u-boot@lists.denx.de/msg271979.html [v3]: https://www.mail-archive.com/u-boot@lists.denx.de/msg272039.html [v4]: https://www.mail-archive.com/u-boot@lists.denx.de/msg272432.html Tien Fong Chee (2): spl: Remove static declaration on spl_mmc_find_device function common: Generic firmware loader for file system common/Makefile | 1 + common/fs_loader.c | 309 +++++++++++++++++++++++++++++++++++++++++++++ common/spl/spl_mmc.c | 2 +- doc/README.firmware_loader | 76 +++++++++++ include/fs_loader.h | 28 ++++ include/spl.h | 2 + 6 files changed, 417 insertions(+), 1 deletion(-) create mode 100644 common/fs_loader.c create mode 100644 doc/README.firmware_loader create mode 100644 include/fs_loader.h -- 2.2.0

6 31

[U-Boot] STM32F746 Discovery - No serial output?
by Francois Dugast 23 Jan '18

23 Jan '18

Hi, I am trying to run the master on a STM32F746 Discovery board [1] by using stm32f746-disco_defconfig. It was built with gcc-arm-none-eabi-5_4-2016q3 [2] and flashed with OpenOCD [3]. A USB-serial adapter is connected to USART6_RX and USART6_TX (pins D0 and D1 of the Arduino connector) and configured for 115200 8N1. No output coming out through the serial interface. It is unlikely to be a hardware issue as output is coming out normally this way when using the U-Boot repository from Emcraft. I do not know what I am doing wrong, can you help me out? Cheers, Francois [1] http://www.st.com/en/evaluation-tools/32f746gdiscovery.html [2] https://launchpad.net/gcc-arm-embedded [3] http://openocd.org [4] https://github.com/EmcraftSystems/u-boot

3 5

[U-Boot] [PATCH] travis-ci: Add qemu-x86_64 target
by Tom Rini 23 Jan '18

23 Jan '18

Add qemu-x86_64 to the list of targets we use for test.py runs. Signed-off-by: Tom Rini <trini(a)konsulko.com> --- .travis.yml | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/.travis.yml b/.travis.yml index 48b7b101f1c6..dab55f34e51d 100644 --- a/.travis.yml +++ b/.travis.yml @@ -311,6 +311,13 @@ matrix: TOOLCHAIN="x86_64" BUILD_ROM="yes" - env: + - TEST_PY_BD="qemu-x86_64" + TEST_PY_TEST_SPEC="not sleep" + QEMU_TARGET="x86_64-softmmu" + BUILDMAN="^qemu-x86_64$" + TOOLCHAIN="x86_64" + BUILD_ROM="yes" + - env: - TEST_PY_BD="zynq_zc702" TEST_PY_TEST_SPEC="not sleep" QEMU_TARGET="arm-softmmu" -- 1.9.1

1 2

[U-Boot] [PATCH] Convert CONFIG_DAVINCI_SPI to Kconfig
by Adam Ford 23 Jan '18

23 Jan '18

This converts the following to Kconfig: CONFIG_DAVINCI_SPI Signed-off-by: Adam Ford <aford173(a)gmail.com> --- configs/da850_am18xxevm_defconfig | 1 + configs/da850evm_defconfig | 1 + configs/da850evm_direct_nor_defconfig | 1 + configs/ea20_defconfig | 1 + configs/k2e_evm_defconfig | 1 + configs/k2e_hs_evm_defconfig | 1 + configs/k2g_evm_defconfig | 1 + configs/k2g_hs_evm_defconfig | 1 + configs/k2hk_evm_defconfig | 1 + configs/k2hk_hs_evm_defconfig | 1 + configs/k2l_evm_defconfig | 1 + configs/legoev3_defconfig | 1 + configs/omapl138_lcdk_defconfig | 1 + drivers/spi/Kconfig | 6 ++++++ include/configs/da850evm.h | 1 - include/configs/ea20.h | 1 - include/configs/legoev3.h | 1 - include/configs/omapl138_lcdk.h | 1 - include/configs/ti_armv7_keystone2.h | 1 - scripts/config_whitelist.txt | 1 - 20 files changed, 19 insertions(+), 6 deletions(-) diff --git a/configs/da850_am18xxevm_defconfig b/configs/da850_am18xxevm_defconfig index 824c383..0675401 100644 --- a/configs/da850_am18xxevm_defconfig +++ b/configs/da850_am18xxevm_defconfig @@ -42,4 +42,5 @@ CONFIG_SPI_FLASH_WINBOND=y CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_DM_SPI=y +CONFIG_DAVINCI_SPI=y # CONFIG_FAT_WRITE is not set diff --git a/configs/da850evm_defconfig b/configs/da850evm_defconfig index 067ddd7..4c2f8f3 100644 --- a/configs/da850evm_defconfig +++ b/configs/da850evm_defconfig @@ -45,4 +45,5 @@ CONFIG_SPI_FLASH_MTD=y CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_DM_SPI=y +CONFIG_DAVINCI_SPI=y # CONFIG_FAT_WRITE is not set diff --git a/configs/da850evm_direct_nor_defconfig b/configs/da850evm_direct_nor_defconfig index b00eea7..0d8a14e 100644 --- a/configs/da850evm_direct_nor_defconfig +++ b/configs/da850evm_direct_nor_defconfig @@ -43,3 +43,4 @@ CONFIG_SPI_FLASH_STMICRO=y CONFIG_SPI_FLASH_WINBOND=y CONFIG_SYS_NS16550=y CONFIG_DM_SPI=y +CONFIG_DAVINCI_SPI=y diff --git a/configs/ea20_defconfig b/configs/ea20_defconfig index eada103..abbb00a 100644 --- a/configs/ea20_defconfig +++ b/configs/ea20_defconfig @@ -32,5 +32,6 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_STMICRO=y CONFIG_SYS_NS16550=y +CONFIG_DAVINCI_SPI=y CONFIG_VIDEO=y # CONFIG_VIDEO_SW_CURSOR is not set diff --git a/configs/k2e_evm_defconfig b/configs/k2e_evm_defconfig index 317d4f0..e6dc298 100644 --- a/configs/k2e_evm_defconfig +++ b/configs/k2e_evm_defconfig @@ -44,6 +44,7 @@ CONFIG_DM_ETH=y CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_DM_SPI=y +CONFIG_DAVINCI_SPI=y CONFIG_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y diff --git a/configs/k2e_hs_evm_defconfig b/configs/k2e_hs_evm_defconfig index b9be606..6c5e167 100644 --- a/configs/k2e_hs_evm_defconfig +++ b/configs/k2e_hs_evm_defconfig @@ -33,6 +33,7 @@ CONFIG_DM_ETH=y CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_DM_SPI=y +CONFIG_DAVINCI_SPI=y CONFIG_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y diff --git a/configs/k2g_evm_defconfig b/configs/k2g_evm_defconfig index 32353e9..6a1f8dc 100644 --- a/configs/k2g_evm_defconfig +++ b/configs/k2g_evm_defconfig @@ -47,6 +47,7 @@ CONFIG_REMOTEPROC_TI_POWER=y CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_DM_SPI=y +CONFIG_DAVINCI_SPI=y CONFIG_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y diff --git a/configs/k2g_hs_evm_defconfig b/configs/k2g_hs_evm_defconfig index 9c4530c..b4985b5 100644 --- a/configs/k2g_hs_evm_defconfig +++ b/configs/k2g_hs_evm_defconfig @@ -35,6 +35,7 @@ CONFIG_REMOTEPROC_TI_POWER=y CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_DM_SPI=y +CONFIG_DAVINCI_SPI=y CONFIG_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y diff --git a/configs/k2hk_evm_defconfig b/configs/k2hk_evm_defconfig index 7115443..1e3905f 100644 --- a/configs/k2hk_evm_defconfig +++ b/configs/k2hk_evm_defconfig @@ -44,6 +44,7 @@ CONFIG_DM_ETH=y CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_DM_SPI=y +CONFIG_DAVINCI_SPI=y CONFIG_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y diff --git a/configs/k2hk_hs_evm_defconfig b/configs/k2hk_hs_evm_defconfig index f65185f..b4b08dd 100644 --- a/configs/k2hk_hs_evm_defconfig +++ b/configs/k2hk_hs_evm_defconfig @@ -33,6 +33,7 @@ CONFIG_DM_ETH=y CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_DM_SPI=y +CONFIG_DAVINCI_SPI=y CONFIG_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y diff --git a/configs/k2l_evm_defconfig b/configs/k2l_evm_defconfig index d2ec226..074bed0 100644 --- a/configs/k2l_evm_defconfig +++ b/configs/k2l_evm_defconfig @@ -44,6 +44,7 @@ CONFIG_DM_ETH=y CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_DM_SPI=y +CONFIG_DAVINCI_SPI=y CONFIG_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y diff --git a/configs/legoev3_defconfig b/configs/legoev3_defconfig index 209250a..d131079 100644 --- a/configs/legoev3_defconfig +++ b/configs/legoev3_defconfig @@ -26,5 +26,6 @@ CONFIG_CMD_DIAG=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_STMICRO=y CONFIG_SYS_NS16550=y +CONFIG_DAVINCI_SPI=y CONFIG_OF_LIBFDT=y # CONFIG_EFI_LOADER is not set diff --git a/configs/omapl138_lcdk_defconfig b/configs/omapl138_lcdk_defconfig index 8d6b12f..6f23206 100644 --- a/configs/omapl138_lcdk_defconfig +++ b/configs/omapl138_lcdk_defconfig @@ -35,4 +35,5 @@ CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_STMICRO=y CONFIG_SPI_FLASH_WINBOND=y CONFIG_SYS_NS16550=y +CONFIG_DAVINCI_SPI=y CONFIG_OF_LIBFDT=y diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 494639f..5e31ee4 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -217,6 +217,12 @@ config ATCSPI200_SPI used to access the SPI flash on AE3XX and AE250 platforms embedding this Andestech IP core. +config DAVINCI_SPI + bool "Davinci & Keystone SPI driver" + depends on ARCH_DAVINCI || ARCH_KEYSTONE + help + Enable the Davinci SPI driver + config TI_QSPI bool "TI QSPI driver" help diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h index 97effa8..9b9aa7f 100644 --- a/include/configs/da850evm.h +++ b/include/configs/da850evm.h @@ -147,7 +147,6 @@ #define CONFIG_CONS_INDEX 1 /* use UART0 for console */ #define CONFIG_SPI -#define CONFIG_DAVINCI_SPI #define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID) #ifdef CONFIG_SPL_BUILD #define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE diff --git a/include/configs/ea20.h b/include/configs/ea20.h index 9b5856e..efc72b3 100644 --- a/include/configs/ea20.h +++ b/include/configs/ea20.h @@ -58,7 +58,6 @@ #define CONFIG_CONS_INDEX 1 /* use UART0 for console */ #define CONFIG_SPI -#define CONFIG_DAVINCI_SPI #define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE #define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID) #define CONFIG_SF_DEFAULT_SPEED 30000000 diff --git a/include/configs/legoev3.h b/include/configs/legoev3.h index 105429b..3439cbe 100644 --- a/include/configs/legoev3.h +++ b/include/configs/legoev3.h @@ -121,7 +121,6 @@ #define CONFIG_CONS_INDEX 1 /* use UART0 for console */ #define CONFIG_SPI -#define CONFIG_DAVINCI_SPI #define CONFIG_SYS_SPI_BASE DAVINCI_SPI0_BASE #define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI0_CLKID) #define CONFIG_SF_DEFAULT_SPEED 50000000 diff --git a/include/configs/omapl138_lcdk.h b/include/configs/omapl138_lcdk.h index 570322e..2cb9911 100644 --- a/include/configs/omapl138_lcdk.h +++ b/include/configs/omapl138_lcdk.h @@ -128,7 +128,6 @@ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } #define CONFIG_SPI -#define CONFIG_DAVINCI_SPI #define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE #define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID) #define CONFIG_SF_DEFAULT_SPEED 30000000 diff --git a/include/configs/ti_armv7_keystone2.h b/include/configs/ti_armv7_keystone2.h index 562bb65..86dd05d 100644 --- a/include/configs/ti_armv7_keystone2.h +++ b/include/configs/ti_armv7_keystone2.h @@ -78,7 +78,6 @@ #endif /* SPI Configuration */ -#define CONFIG_DAVINCI_SPI #define CONFIG_SYS_SPI_CLK ks_clk_get_rate(KS2_CLK1_6) #define CONFIG_SF_DEFAULT_SPEED 30000000 #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 11a53166..9985633 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -353,7 +353,6 @@ CONFIG_DA850_AM18X_EVM CONFIG_DA850_EVM_MAX_CPU_CLK CONFIG_DA850_LOWLEVEL CONFIG_DA8XX_GPIO -CONFIG_DAVINCI_SPI CONFIG_DBAU1000 CONFIG_DBAU1X00 CONFIG_DBGU -- 2.7.4

2 1

[U-Boot] [PATCH] Convert CONFIG_USB_MUSB_HCD et al to Kconfig
by Adam Ford 23 Jan '18

23 Jan '18

This converts the following to Kconfig: CONFIG_USB_MUSB_HCD CONFIG_USB_MUSB_UDC CONFIG_USB_DAVINCI CONFIG_USB_OMAP3 CONFIG_USB_DA8XX CONFIG_USB_AM35X Signed-off-by: Adam Ford <aford173(a)gmail.com> --- configs/am3517_crane_defconfig | 2 ++ configs/cm_t35_defconfig | 2 ++ configs/duovero_defconfig | 2 ++ configs/igep0032_defconfig | 3 +++ configs/igep00x0_defconfig | 3 +++ configs/nokia_rx51_defconfig | 4 ++++ configs/omap3_evm_defconfig | 1 + configs/omap3_logic_defconfig | 1 + configs/omap3_zoom1_defconfig | 3 +++ configs/omap4_panda_defconfig | 2 ++ configs/omap4_sdp4430_defconfig | 3 +++ drivers/usb/Kconfig | 2 ++ drivers/usb/musb/Kconfig | 29 +++++++++++++++++++++++++++++ include/configs/am3517_crane.h | 2 -- include/configs/cm_t35.h | 2 -- include/configs/cm_t3517.h | 1 - include/configs/eco5pk.h | 2 -- include/configs/nokia_rx51.h | 3 --- include/configs/omap3_evm.h | 1 - include/configs/omap3_igep00x0.h | 2 -- include/configs/omap3_logic.h | 2 -- include/configs/omap3_zoom1.h | 2 -- include/configs/ti_omap4_common.h | 2 -- scripts/config_whitelist.txt | 4 ---- 24 files changed, 57 insertions(+), 23 deletions(-) diff --git a/configs/am3517_crane_defconfig b/configs/am3517_crane_defconfig index a1766d9..2e8d943 100644 --- a/configs/am3517_crane_defconfig +++ b/configs/am3517_crane_defconfig @@ -31,4 +31,6 @@ CONFIG_SYS_NAND_BUSWIDTH_16BIT=y CONFIG_SPL_NAND_SIMPLE=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_USB_MUSB_HCD=y +CONFIG_USB_AM35X=y CONFIG_USB_STORAGE=y diff --git a/configs/cm_t35_defconfig b/configs/cm_t35_defconfig index c61a93b..cfb68b1 100644 --- a/configs/cm_t35_defconfig +++ b/configs/cm_t35_defconfig @@ -50,6 +50,8 @@ CONFIG_SYS_NS16550=y CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_EHCI_HCD=y +CONFIG_USB_MUSB_UDC=y +CONFIG_USB_OMAP3=y CONFIG_USB_STORAGE=y CONFIG_LCD=y CONFIG_OF_LIBFDT=y diff --git a/configs/duovero_defconfig b/configs/duovero_defconfig index f52cbe7..a510294 100644 --- a/configs/duovero_defconfig +++ b/configs/duovero_defconfig @@ -32,6 +32,8 @@ CONFIG_SYS_NS16550=y CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_EHCI_HCD=y +CONFIG_USB_MUSB_UDC=y +CONFIG_USB_OMAP3=y CONFIG_USB_STORAGE=y CONFIG_FAT_WRITE=y CONFIG_OF_LIBFDT=y diff --git a/configs/igep0032_defconfig b/configs/igep0032_defconfig index e394aa5..60cce77 100644 --- a/configs/igep0032_defconfig +++ b/configs/igep0032_defconfig @@ -39,6 +39,9 @@ CONFIG_SMC911X_BASE=0x2C000000 CONFIG_SMC911X_32_BIT=y CONFIG_SYS_NS16550=y CONFIG_OMAP3_SPI=y +CONFIG_USB=y +CONFIG_USB_MUSB_UDC=y +CONFIG_USB_OMAP3=y CONFIG_FAT_WRITE=y CONFIG_BCH=y CONFIG_OF_LIBFDT=y diff --git a/configs/igep00x0_defconfig b/configs/igep00x0_defconfig index d70d4c6..d8ece6b 100644 --- a/configs/igep00x0_defconfig +++ b/configs/igep00x0_defconfig @@ -40,6 +40,9 @@ CONFIG_SMC911X_BASE=0x2C000000 CONFIG_SMC911X_32_BIT=y CONFIG_SYS_NS16550=y CONFIG_OMAP3_SPI=y +CONFIG_USB=y +CONFIG_USB_MUSB_UDC=y +CONFIG_USB_OMAP3=y CONFIG_FAT_WRITE=y CONFIG_BCH=y CONFIG_OF_LIBFDT=y diff --git a/configs/nokia_rx51_defconfig b/configs/nokia_rx51_defconfig index 9057811..570bb3f 100644 --- a/configs/nokia_rx51_defconfig +++ b/configs/nokia_rx51_defconfig @@ -26,6 +26,10 @@ CONFIG_CMD_FAT=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_OMAP3_SPI=y +CONFIG_USB=y +CONFIG_USB_MUSB_HCD=y +CONFIG_USB_MUSB_UDC=y +CONFIG_USB_OMAP3=y CONFIG_VIDEO=y CONFIG_CFB_CONSOLE_ANSI=y # CONFIG_VGA_AS_SINGLE_DEVICE is not set diff --git a/configs/omap3_evm_defconfig b/configs/omap3_evm_defconfig index c38f142..f241ff8 100644 --- a/configs/omap3_evm_defconfig +++ b/configs/omap3_evm_defconfig @@ -53,6 +53,7 @@ CONFIG_SYS_NS16550=y CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_EHCI_HCD=y +CONFIG_USB_OMAP3=y CONFIG_USB_MUSB_GADGET=y CONFIG_USB_MUSB_OMAP2PLUS=y CONFIG_USB_GADGET=y diff --git a/configs/omap3_logic_defconfig b/configs/omap3_logic_defconfig index 5b00c06..a34401f 100644 --- a/configs/omap3_logic_defconfig +++ b/configs/omap3_logic_defconfig @@ -48,6 +48,7 @@ CONFIG_SYS_NS16550=y CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_EHCI_HCD=y +CONFIG_USB_OMAP3=y CONFIG_USB_MUSB_GADGET=y CONFIG_USB_MUSB_OMAP2PLUS=y CONFIG_USB_STORAGE=y diff --git a/configs/omap3_zoom1_defconfig b/configs/omap3_zoom1_defconfig index 6639c7e..db867b1 100644 --- a/configs/omap3_zoom1_defconfig +++ b/configs/omap3_zoom1_defconfig @@ -41,5 +41,8 @@ CONFIG_SMC911X_BASE=0x08000000 CONFIG_SMC911X_32_BIT=y CONFIG_SYS_NS16550=y CONFIG_OMAP3_SPI=y +CONFIG_USB=y +CONFIG_USB_MUSB_UDC=y +CONFIG_USB_OMAP3=y CONFIG_FAT_WRITE=y CONFIG_OF_LIBFDT=y diff --git a/configs/omap4_panda_defconfig b/configs/omap4_panda_defconfig index 0faea77..aa0c36e 100644 --- a/configs/omap4_panda_defconfig +++ b/configs/omap4_panda_defconfig @@ -31,6 +31,8 @@ CONFIG_SYS_NS16550=y CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_EHCI_HCD=y +CONFIG_USB_MUSB_UDC=y +CONFIG_USB_OMAP3=y CONFIG_USB_STORAGE=y CONFIG_USB_HOST_ETHER=y CONFIG_USB_ETHER_SMSC95XX=y diff --git a/configs/omap4_sdp4430_defconfig b/configs/omap4_sdp4430_defconfig index b7ba1f3..ac49571 100644 --- a/configs/omap4_sdp4430_defconfig +++ b/configs/omap4_sdp4430_defconfig @@ -27,5 +27,8 @@ CONFIG_ENV_IS_IN_MMC=y CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_OMAP3_SPI=y +CONFIG_USB=y +CONFIG_USB_MUSB_UDC=y +CONFIG_USB_OMAP3=y CONFIG_FAT_WRITE=y CONFIG_OF_LIBFDT=y diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig index e7658b4..13e9e49 100644 --- a/drivers/usb/Kconfig +++ b/drivers/usb/Kconfig @@ -51,6 +51,8 @@ source "drivers/usb/host/Kconfig" source "drivers/usb/dwc3/Kconfig" +source "drivers/usb/musb/Kconfig" + source "drivers/usb/musb-new/Kconfig" source "drivers/usb/emul/Kconfig" diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig new file mode 100644 index 0000000..4e2be37 --- /dev/null +++ b/drivers/usb/musb/Kconfig @@ -0,0 +1,29 @@ +# +# (C) Copyright 2017 +# Adam Ford, Logic PD, aford173(a)gmail.com +# +# SPDX-License-Identifier: GPL-2.0+ +# + +comment "Legacy MUSB Support" + +config USB_MUSB_HCD + bool "Legacy MUSB Host Controller" + +config USB_MUSB_UDC + bool "Legacy USB Device Controller" + +config USB_DAVINCI + bool "Legacy MUSB DaVinci" + +config USB_OMAP3 + bool "Legacy MUSB OMAP3 / OMAP4" + depends on ARCH_OMAP2PLUS + +config USB_DA8XX + bool "Legacy MUSB DA8xx/OMAP-L1x" + depends on ARCH_DAVINCI + +config USB_AM35X + bool"Legacy MUSB AM35x" + depends on ARCH_OMAP2PLUS && !USB_OMAP3 diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h index 400a06e..16212ef 100644 --- a/include/configs/am3517_crane.h +++ b/include/configs/am3517_crane.h @@ -72,8 +72,6 @@ * Enable CONFIG_USB_MUSB_HCD for Host functionalities MSC, keyboard * Enable CONFIG_USB_MUSB_UDC for Device functionalities. */ -#define CONFIG_USB_AM35X 1 -#define CONFIG_USB_MUSB_HCD 1 #ifdef CONFIG_USB_AM35X diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h index dc1b6b5..8abe870 100644 --- a/include/configs/cm_t35.h +++ b/include/configs/cm_t35.h @@ -72,8 +72,6 @@ 115200} /* USB */ -#define CONFIG_USB_OMAP3 -#define CONFIG_USB_MUSB_UDC #define CONFIG_TWL4030_USB /* USB device configuration */ diff --git a/include/configs/cm_t3517.h b/include/configs/cm_t3517.h index f263e62..fe8b39a 100644 --- a/include/configs/cm_t3517.h +++ b/include/configs/cm_t3517.h @@ -80,7 +80,6 @@ /* USB */ #ifndef CONFIG_USB_MUSB_AM35X -#define CONFIG_USB_OMAP3 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 146 #define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 147 #endif /* CONFIG_USB_MUSB_AM35X */ diff --git a/include/configs/eco5pk.h b/include/configs/eco5pk.h index 9dbd7a2..a75932f 100644 --- a/include/configs/eco5pk.h +++ b/include/configs/eco5pk.h @@ -15,8 +15,6 @@ #include "tam3517-common.h" -#undef CONFIG_USB_OMAP3 - /* Our console port is port3 */ #undef CONFIG_CONS_INDEX #undef CONFIG_SYS_NS16550_COM1 diff --git a/include/configs/nokia_rx51.h b/include/configs/nokia_rx51.h index b7fe734..1c02a8c 100644 --- a/include/configs/nokia_rx51.h +++ b/include/configs/nokia_rx51.h @@ -83,9 +83,6 @@ #define CONFIG_SYS_BAUDRATE_TABLE { 4800, 9600, 19200, 38400, 57600, 115200 } /* USB */ -#define CONFIG_USB_MUSB_UDC -#define CONFIG_USB_MUSB_HCD -#define CONFIG_USB_OMAP3 #define CONFIG_TWL4030_USB /* USB device configuration */ diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h index 0eefb84..e1a19ae 100644 --- a/include/configs/omap3_evm.h +++ b/include/configs/omap3_evm.h @@ -76,7 +76,6 @@ #endif /* CONFIG_NAND */ /* MUSB */ -#define CONFIG_USB_OMAP3 /* USB EHCI */ #define CONFIG_SYS_USB_FAT_BOOT_PARTITION 1 diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h index 91b3a23..9b815e0 100644 --- a/include/configs/omap3_igep00x0.h +++ b/include/configs/omap3_igep00x0.h @@ -42,8 +42,6 @@ #define GPIO_IGEP00X0_REVISION_DETECTION 129 /* USB */ -#define CONFIG_USB_MUSB_UDC 1 -#define CONFIG_USB_OMAP3 1 #define CONFIG_TWL4030_USB 1 /* USB device configuration */ diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h index 1e4e42a..a4b29f1 100644 --- a/include/configs/omap3_logic.h +++ b/include/configs/omap3_logic.h @@ -49,8 +49,6 @@ /* Hardware drivers */ -#define CONFIG_USB_OMAP3 - /* I2C */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */ diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h index d1ff48d..e5e4bc4 100644 --- a/include/configs/omap3_zoom1.h +++ b/include/configs/omap3_zoom1.h @@ -35,8 +35,6 @@ */ /* USB */ -#define CONFIG_USB_MUSB_UDC 1 -#define CONFIG_USB_OMAP3 1 #define CONFIG_TWL4030_USB 1 /* USB device configuration */ diff --git a/include/configs/ti_omap4_common.h b/include/configs/ti_omap4_common.h index 91b2132..844a9e5 100644 --- a/include/configs/ti_omap4_common.h +++ b/include/configs/ti_omap4_common.h @@ -61,8 +61,6 @@ #endif /* USB */ -#define CONFIG_USB_MUSB_UDC 1 -#define CONFIG_USB_OMAP3 1 /* USB device configuration */ #define CONFIG_USB_DEVICE 1 diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 7ff11c5..fdf9e55 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -4883,7 +4883,6 @@ CONFIG_USBD_VENDORID CONFIG_USBID_ADDR CONFIG_USBNET_DEV_ADDR CONFIG_USBTTY -CONFIG_USB_AM35X CONFIG_USB_ATMEL CONFIG_USB_ATMEL_CLK_SEL_PLLB CONFIG_USB_ATMEL_CLK_SEL_UPLL @@ -4944,16 +4943,13 @@ CONFIG_USB_INVENTRA_DMA CONFIG_USB_ISP1301_I2C_ADDR CONFIG_USB_MAX_CONTROLLER_COUNT CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT -CONFIG_USB_MUSB_HCD CONFIG_USB_MUSB_TIMEOUT CONFIG_USB_MUSB_TUSB6010 -CONFIG_USB_MUSB_UDC CONFIG_USB_OHCI CONFIG_USB_OHCI_EP93XX CONFIG_USB_OHCI_LPC32XX CONFIG_USB_OHCI_NEW CONFIG_USB_OHCI_SUNXI -CONFIG_USB_OMAP3 CONFIG_USB_OTG CONFIG_USB_OTG_BLACKLIST_HUB CONFIG_USB_PHY_CFG_BASE -- 2.7.4

2 1

[U-Boot] [PATCH V2] Convert CONFIG_USB_MUSB_OMAP2PLUS et al to Kconfig
by Adam Ford 23 Jan '18

23 Jan '18

This converts the following to Kconfig: CONFIG_USB_MUSB_OMAP2PLUS CONFIG_USB_MUSB_AM35X CONFIG_USB_MUSB_DSPS CONFIG_USB_MUSB_PIO_ONLY Signed-off-by: Adam Ford <aford173(a)gmail.com> --- Changes to V2: Add AM35X and DSPS. Make CONFIG_USB_MUSB_PIO_ONLY enabled when USB_MUSB_PIC32, USB_MUSB_OMAP2PLUS, USB_MUSB_AM35X, USB_MUSB_DSPS, or USB_MUSB_SUNXI are enabled configs/am335x_baltos_defconfig | 1 + configs/am335x_boneblack_defconfig | 1 + configs/am335x_boneblack_vboot_defconfig | 1 + configs/am335x_evm_defconfig | 1 + configs/am335x_evm_nor_defconfig | 1 + configs/am335x_evm_norboot_defconfig | 1 + configs/am335x_evm_spiboot_defconfig | 1 + configs/am335x_evm_usbspl_defconfig | 1 + configs/am335x_hs_evm_defconfig | 1 + configs/am335x_hs_evm_uart_defconfig | 1 + configs/am3517_evm_defconfig | 1 + configs/birdland_bav335a_defconfig | 1 + configs/birdland_bav335b_defconfig | 1 + configs/brppt1_mmc_defconfig | 1 + configs/brppt1_nand_defconfig | 1 + configs/brppt1_spi_defconfig | 1 + configs/brxre1_defconfig | 1 + configs/chiliboard_defconfig | 1 + configs/cm_t3517_defconfig | 1 + configs/draco_defconfig | 1 + configs/etamin_defconfig | 1 + configs/kc1_defconfig | 1 + configs/omap3_beagle_defconfig | 1 + configs/omap3_evm_defconfig | 1 + configs/omap3_logic_defconfig | 1 + configs/pcm051_rev1_defconfig | 1 + configs/pcm051_rev3_defconfig | 1 + configs/pengwyn_defconfig | 1 + configs/pxm2_defconfig | 1 + configs/rastaban_defconfig | 1 + configs/rut_defconfig | 1 + configs/sniper_defconfig | 1 + configs/thuban_defconfig | 1 + drivers/usb/musb-new/Kconfig | 17 +++++++++++++++++ include/configs/am335x_evm.h | 2 -- include/configs/am3517_evm.h | 2 -- include/configs/baltos.h | 2 -- include/configs/bav335x.h | 2 -- include/configs/brppt1.h | 2 -- include/configs/brxre1.h | 2 -- include/configs/chiliboard.h | 2 -- include/configs/cm_t3517.h | 3 --- include/configs/kc1.h | 3 --- include/configs/omap3_beagle.h | 2 -- include/configs/omap3_evm.h | 2 -- include/configs/omap3_logic.h | 2 -- include/configs/pcm051.h | 2 -- include/configs/pengwyn.h | 2 -- include/configs/pic32mzdask.h | 1 - include/configs/siemens-am33x-common.h | 2 -- include/configs/sniper.h | 2 -- include/configs/sunxi-common.h | 4 ---- scripts/config_whitelist.txt | 4 ---- 53 files changed, 50 insertions(+), 43 deletions(-) diff --git a/configs/am335x_baltos_defconfig b/configs/am335x_baltos_defconfig index 0ef9f42..548e045 100644 --- a/configs/am335x_baltos_defconfig +++ b/configs/am335x_baltos_defconfig @@ -55,6 +55,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" diff --git a/configs/am335x_boneblack_defconfig b/configs/am335x_boneblack_defconfig index 55e0ebd..f351619 100644 --- a/configs/am335x_boneblack_defconfig +++ b/configs/am335x_boneblack_defconfig @@ -32,6 +32,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" diff --git a/configs/am335x_boneblack_vboot_defconfig b/configs/am335x_boneblack_vboot_defconfig index fe5b9e7..e141106 100644 --- a/configs/am335x_boneblack_vboot_defconfig +++ b/configs/am335x_boneblack_vboot_defconfig @@ -42,6 +42,7 @@ CONFIG_OMAP_TIMER=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" diff --git a/configs/am335x_evm_defconfig b/configs/am335x_evm_defconfig index 9c97009..9e79d1c 100644 --- a/configs/am335x_evm_defconfig +++ b/configs/am335x_evm_defconfig @@ -47,6 +47,7 @@ CONFIG_DM_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y CONFIG_USB_MUSB_TI=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" diff --git a/configs/am335x_evm_nor_defconfig b/configs/am335x_evm_nor_defconfig index 1813003..14aa267 100644 --- a/configs/am335x_evm_nor_defconfig +++ b/configs/am335x_evm_nor_defconfig @@ -34,6 +34,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" diff --git a/configs/am335x_evm_norboot_defconfig b/configs/am335x_evm_norboot_defconfig index b38d7f6..22182f5 100644 --- a/configs/am335x_evm_norboot_defconfig +++ b/configs/am335x_evm_norboot_defconfig @@ -30,6 +30,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" diff --git a/configs/am335x_evm_spiboot_defconfig b/configs/am335x_evm_spiboot_defconfig index 7a20576..71d6a28 100644 --- a/configs/am335x_evm_spiboot_defconfig +++ b/configs/am335x_evm_spiboot_defconfig @@ -32,6 +32,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" diff --git a/configs/am335x_evm_usbspl_defconfig b/configs/am335x_evm_usbspl_defconfig index 1e80017..10d6d38 100644 --- a/configs/am335x_evm_usbspl_defconfig +++ b/configs/am335x_evm_usbspl_defconfig @@ -38,6 +38,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" diff --git a/configs/am335x_hs_evm_defconfig b/configs/am335x_hs_evm_defconfig index 78cf48d..a26fd09 100644 --- a/configs/am335x_hs_evm_defconfig +++ b/configs/am335x_hs_evm_defconfig @@ -53,6 +53,7 @@ CONFIG_DM_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y CONFIG_USB_MUSB_TI=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" diff --git a/configs/am335x_hs_evm_uart_defconfig b/configs/am335x_hs_evm_uart_defconfig index 09aab29..7f05d56 100644 --- a/configs/am335x_hs_evm_uart_defconfig +++ b/configs/am335x_hs_evm_uart_defconfig @@ -53,6 +53,7 @@ CONFIG_DM_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y CONFIG_USB_MUSB_TI=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_DOWNLOAD=y diff --git a/configs/am3517_evm_defconfig b/configs/am3517_evm_defconfig index e6c17c7..bb7cc3f 100644 --- a/configs/am3517_evm_defconfig +++ b/configs/am3517_evm_defconfig @@ -40,5 +40,6 @@ CONFIG_SPL_NAND_SIMPLE=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y +CONFIG_USB_MUSB_AM35X=y # CONFIG_FAT_WRITE is not set CONFIG_BCH=y diff --git a/configs/birdland_bav335a_defconfig b/configs/birdland_bav335a_defconfig index 61518f5..d6d5d71 100644 --- a/configs/birdland_bav335a_defconfig +++ b/configs/birdland_bav335a_defconfig @@ -62,6 +62,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" diff --git a/configs/birdland_bav335b_defconfig b/configs/birdland_bav335b_defconfig index c7360c3..0c14595 100644 --- a/configs/birdland_bav335b_defconfig +++ b/configs/birdland_bav335b_defconfig @@ -62,6 +62,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" diff --git a/configs/brppt1_mmc_defconfig b/configs/brppt1_mmc_defconfig index c41a7b4..aa3e317 100644 --- a/configs/brppt1_mmc_defconfig +++ b/configs/brppt1_mmc_defconfig @@ -55,6 +55,7 @@ CONFIG_PHYLIB=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_SYS_WHITE_ON_BLACK=y CONFIG_LCD=y diff --git a/configs/brppt1_nand_defconfig b/configs/brppt1_nand_defconfig index 3844413..c8063b9 100644 --- a/configs/brppt1_nand_defconfig +++ b/configs/brppt1_nand_defconfig @@ -57,6 +57,7 @@ CONFIG_PHYLIB=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_SYS_WHITE_ON_BLACK=y CONFIG_LCD=y diff --git a/configs/brppt1_spi_defconfig b/configs/brppt1_spi_defconfig index 25d8837..6385b1a 100644 --- a/configs/brppt1_spi_defconfig +++ b/configs/brppt1_spi_defconfig @@ -65,6 +65,7 @@ CONFIG_SYS_NS16550=y CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_SYS_WHITE_ON_BLACK=y CONFIG_LCD=y diff --git a/configs/brxre1_defconfig b/configs/brxre1_defconfig index 0c2d7ed..15245dc 100644 --- a/configs/brxre1_defconfig +++ b/configs/brxre1_defconfig @@ -56,6 +56,7 @@ CONFIG_PHYLIB=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_SYS_WHITE_ON_BLACK=y CONFIG_LCD=y diff --git a/configs/chiliboard_defconfig b/configs/chiliboard_defconfig index bc69df0..a32dab7 100644 --- a/configs/chiliboard_defconfig +++ b/configs/chiliboard_defconfig @@ -45,6 +45,7 @@ CONFIG_SYS_NS16550=y CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_FAT_WRITE=y CONFIG_LZO=y diff --git a/configs/cm_t3517_defconfig b/configs/cm_t3517_defconfig index 819a95b..fa78bde 100644 --- a/configs/cm_t3517_defconfig +++ b/configs/cm_t3517_defconfig @@ -48,6 +48,7 @@ CONFIG_SYS_NS16550=y CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y +CONFIG_USB_MUSB_AM35X=y CONFIG_USB_STORAGE=y CONFIG_LCD=y CONFIG_OF_LIBFDT=y diff --git a/configs/draco_defconfig b/configs/draco_defconfig index be0105f..5444260 100644 --- a/configs/draco_defconfig +++ b/configs/draco_defconfig @@ -64,6 +64,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Siemens AG" diff --git a/configs/etamin_defconfig b/configs/etamin_defconfig index 8e8ef6f..608faf6 100644 --- a/configs/etamin_defconfig +++ b/configs/etamin_defconfig @@ -64,6 +64,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Siemens AG" diff --git a/configs/kc1_defconfig b/configs/kc1_defconfig index 0ddf64c..e828405 100644 --- a/configs/kc1_defconfig +++ b/configs/kc1_defconfig @@ -38,6 +38,7 @@ CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_OMAP2PLUS=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" CONFIG_USB_GADGET_VENDOR_NUM=0x0451 diff --git a/configs/omap3_beagle_defconfig b/configs/omap3_beagle_defconfig index ad72079..1fea12a 100644 --- a/configs/omap3_beagle_defconfig +++ b/configs/omap3_beagle_defconfig @@ -48,6 +48,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_OMAP2PLUS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="TI" diff --git a/configs/omap3_evm_defconfig b/configs/omap3_evm_defconfig index 5103e9f..c38f142 100644 --- a/configs/omap3_evm_defconfig +++ b/configs/omap3_evm_defconfig @@ -54,6 +54,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_OMAP2PLUS=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" CONFIG_USB_GADGET_VENDOR_NUM=0x0451 diff --git a/configs/omap3_logic_defconfig b/configs/omap3_logic_defconfig index db72e6f..5b00c06 100644 --- a/configs/omap3_logic_defconfig +++ b/configs/omap3_logic_defconfig @@ -49,6 +49,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_OMAP2PLUS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="TI" diff --git a/configs/pcm051_rev1_defconfig b/configs/pcm051_rev1_defconfig index 273fc30..c16711a 100644 --- a/configs/pcm051_rev1_defconfig +++ b/configs/pcm051_rev1_defconfig @@ -58,6 +58,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_ETHER=y diff --git a/configs/pcm051_rev3_defconfig b/configs/pcm051_rev3_defconfig index f1ddaa6..a8fe7af 100644 --- a/configs/pcm051_rev3_defconfig +++ b/configs/pcm051_rev3_defconfig @@ -58,6 +58,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_ETHER=y diff --git a/configs/pengwyn_defconfig b/configs/pengwyn_defconfig index 4bb6245..78a6b7d 100644 --- a/configs/pengwyn_defconfig +++ b/configs/pengwyn_defconfig @@ -62,6 +62,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_FAT_WRITE=y diff --git a/configs/pxm2_defconfig b/configs/pxm2_defconfig index 0ec1591..f682300 100644 --- a/configs/pxm2_defconfig +++ b/configs/pxm2_defconfig @@ -67,6 +67,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Siemens AG" diff --git a/configs/rastaban_defconfig b/configs/rastaban_defconfig index 5ef1740..c714b07 100644 --- a/configs/rastaban_defconfig +++ b/configs/rastaban_defconfig @@ -64,6 +64,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Siemens AG" diff --git a/configs/rut_defconfig b/configs/rut_defconfig index 1711fc7..2269747 100644 --- a/configs/rut_defconfig +++ b/configs/rut_defconfig @@ -68,6 +68,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Siemens AG" diff --git a/configs/sniper_defconfig b/configs/sniper_defconfig index a8a592f..c75b1ba 100644 --- a/configs/sniper_defconfig +++ b/configs/sniper_defconfig @@ -39,6 +39,7 @@ CONFIG_MMC_OMAP_HS=y CONFIG_SYS_NS16550=y CONFIG_USB=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_OMAP2PLUS=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" CONFIG_USB_GADGET_VENDOR_NUM=0x0451 diff --git a/configs/thuban_defconfig b/configs/thuban_defconfig index 2575c00..df76145 100644 --- a/configs/thuban_defconfig +++ b/configs/thuban_defconfig @@ -64,6 +64,7 @@ CONFIG_OMAP3_SPI=y CONFIG_USB=y CONFIG_USB_MUSB_HOST=y CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Siemens AG" diff --git a/drivers/usb/musb-new/Kconfig b/drivers/usb/musb-new/Kconfig index caba42c..ea5bae2 100644 --- a/drivers/usb/musb-new/Kconfig +++ b/drivers/usb/musb-new/Kconfig @@ -23,6 +23,16 @@ config USB_MUSB_TI speed USB controller based on the Mentor Graphics silicon IP. +config USB_MUSB_OMAP2PLUS + tristate "OMAP2430 and onwards" + depends on ARCH_OMAP2PLUS + +config USB_MUSB_AM35X + bool "AM35x" + +config USB_MUSB_DSPS + bool "TI DSPS platforms" + if USB_MUSB_HOST || USB_MUSB_GADGET config USB_MUSB_PIC32 @@ -41,3 +51,10 @@ config USB_MUSB_SUNXI used on almost all sunxi boards. endif + +config USB_MUSB_PIO_ONLY + bool "Disable DMA (always use PIO)" + default y if USB_MUSB_AM35X || USB_MUSB_PIC32 || USB_MUSB_OMAP2PLUS || USB_MUSB_DSPS || USB_MUSB_SUNXI + help + All data is copied between memory and FIFO by the CPU. + DMA controllers are ignored. diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index 856c546..31ab503 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -228,8 +228,6 @@ * add mass storage support and for gadget we add both RNDIS ethernet * and DFU. */ -#define CONFIG_USB_MUSB_DSPS -#define CONFIG_USB_MUSB_PIO_ONLY #define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT #define CONFIG_AM335X_USB0 #define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h index 33ed85e..ac5070d 100644 --- a/include/configs/am3517_evm.h +++ b/include/configs/am3517_evm.h @@ -42,8 +42,6 @@ * Enable CONFIG_USB_MUSB_HOST for Host functionalities MSC, keyboard * Enable CONFIG_USB_MUSB_GADGET for Device functionalities. */ -#define CONFIG_USB_MUSB_AM35X -#define CONFIG_USB_MUSB_PIO_ONLY #ifdef CONFIG_USB_MUSB_AM35X diff --git a/include/configs/baltos.h b/include/configs/baltos.h index 3fc9e2f..939ee3b 100644 --- a/include/configs/baltos.h +++ b/include/configs/baltos.h @@ -272,8 +272,6 @@ * add mass storage support and for gadget we add both RNDIS ethernet * and DFU. */ -#define CONFIG_USB_MUSB_DSPS -#define CONFIG_USB_MUSB_PIO_ONLY #define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT #define CONFIG_AM335X_USB0 #define CONFIG_AM335X_USB0_MODE MUSB_HOST diff --git a/include/configs/bav335x.h b/include/configs/bav335x.h index 8917bbe..d084af8 100644 --- a/include/configs/bav335x.h +++ b/include/configs/bav335x.h @@ -394,8 +394,6 @@ DEFAULT_LINUX_BOOT_ENV \ * add mass storage support and for gadget we add both RNDIS ethernet * and DFU. */ -#define CONFIG_USB_MUSB_DSPS -#define CONFIG_USB_MUSB_PIO_ONLY #define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT #define CONFIG_AM335X_USB0 #define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL diff --git a/include/configs/brppt1.h b/include/configs/brppt1.h index 2dadcae..1f57334 100644 --- a/include/configs/brppt1.h +++ b/include/configs/brppt1.h @@ -210,8 +210,6 @@ MMCARGS #endif /* CONFIG_NAND */ /* USB configuration */ -#define CONFIG_USB_MUSB_DSPS -#define CONFIG_USB_MUSB_PIO_ONLY #define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT #define CONFIG_AM335X_USB0 #define CONFIG_AM335X_USB0_MODE MUSB_HOST diff --git a/include/configs/brxre1.h b/include/configs/brxre1.h index 8f92d7a..09042d4 100644 --- a/include/configs/brxre1.h +++ b/include/configs/brxre1.h @@ -80,8 +80,6 @@ BUR_COMMON_ENV \ #define CONFIG_INITRD_TAG /* USB configuration */ -#define CONFIG_USB_MUSB_DSPS -#define CONFIG_USB_MUSB_PIO_ONLY #define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT #define CONFIG_AM335X_USB0 #define CONFIG_AM335X_USB0_MODE MUSB_HOST diff --git a/include/configs/chiliboard.h b/include/configs/chiliboard.h index 92fd235..89740ba 100644 --- a/include/configs/chiliboard.h +++ b/include/configs/chiliboard.h @@ -152,9 +152,7 @@ /* NAND: SPL related configs */ /* USB configuration */ -#define CONFIG_USB_MUSB_DSPS #define CONFIG_ARCH_MISC_INIT -#define CONFIG_USB_MUSB_PIO_ONLY #define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT #define CONFIG_AM335X_USB1 #define CONFIG_AM335X_USB1_MODE MUSB_HOST diff --git a/include/configs/cm_t3517.h b/include/configs/cm_t3517.h index a472b9f..f263e62 100644 --- a/include/configs/cm_t3517.h +++ b/include/configs/cm_t3517.h @@ -78,14 +78,11 @@ 115200} /* USB */ -#define CONFIG_USB_MUSB_AM35X #ifndef CONFIG_USB_MUSB_AM35X #define CONFIG_USB_OMAP3 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 146 #define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 147 -#else /* !CONFIG_USB_MUSB_AM35X */ -#define CONFIG_USB_MUSB_PIO_ONLY #endif /* CONFIG_USB_MUSB_AM35X */ /* commands to include */ diff --git a/include/configs/kc1.h b/include/configs/kc1.h index 8d8dc26..94c3d0a 100644 --- a/include/configs/kc1.h +++ b/include/configs/kc1.h @@ -115,9 +115,6 @@ * USB gadget */ -#define CONFIG_USB_MUSB_PIO_ONLY -#define CONFIG_USB_MUSB_OMAP2PLUS - /* * Environment */ diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index 394bfb7..f21a843 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -43,8 +43,6 @@ #define CONFIG_SYS_I2C_NOPROBES {{0x0, 0x0}} /* USB */ -#define CONFIG_USB_MUSB_OMAP2PLUS -#define CONFIG_USB_MUSB_PIO_ONLY #define CONFIG_TWL4030_USB 1 /* USB EHCI */ diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h index 42f2153..0eefb84 100644 --- a/include/configs/omap3_evm.h +++ b/include/configs/omap3_evm.h @@ -77,8 +77,6 @@ /* MUSB */ #define CONFIG_USB_OMAP3 -#define CONFIG_USB_MUSB_OMAP2PLUS -#define CONFIG_USB_MUSB_PIO_ONLY /* USB EHCI */ #define CONFIG_SYS_USB_FAT_BOOT_PARTITION 1 diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h index b095814..1e4e42a 100644 --- a/include/configs/omap3_logic.h +++ b/include/configs/omap3_logic.h @@ -55,8 +55,6 @@ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */ /* USB */ -#define CONFIG_USB_MUSB_OMAP2PLUS -#define CONFIG_USB_MUSB_PIO_ONLY /* TWL4030 */ #define CONFIG_TWL4030_USB diff --git a/include/configs/pcm051.h b/include/configs/pcm051.h index 79f3f48..c6ff1e1 100644 --- a/include/configs/pcm051.h +++ b/include/configs/pcm051.h @@ -126,8 +126,6 @@ /* * USB configuration */ -#define CONFIG_USB_MUSB_DSPS -#define CONFIG_USB_MUSB_PIO_ONLY #define CONFIG_AM335X_USB0 #define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL #define CONFIG_AM335X_USB1 diff --git a/include/configs/pengwyn.h b/include/configs/pengwyn.h index 8afd64e..d9a50ca 100644 --- a/include/configs/pengwyn.h +++ b/include/configs/pengwyn.h @@ -162,8 +162,6 @@ * board schematic and physical port wired to each. Then for host we * add mass storage support. */ -#define CONFIG_USB_MUSB_DSPS -#define CONFIG_USB_MUSB_PIO_ONLY #define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT #define CONFIG_AM335X_USB0 #define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL diff --git a/include/configs/pic32mzdask.h b/include/configs/pic32mzdask.h index 97636fe..0bb5126 100644 --- a/include/configs/pic32mzdask.h +++ b/include/configs/pic32mzdask.h @@ -80,7 +80,6 @@ /*-------------------------------------------------- * USB Configuration */ -#define CONFIG_USB_MUSB_PIO_ONLY /*----------------------------------------------------------------------- * File System Configuration diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h index 78708a2..85b6412 100644 --- a/include/configs/siemens-am33x-common.h +++ b/include/configs/siemens-am33x-common.h @@ -168,8 +168,6 @@ /* * USB configuration */ -#define CONFIG_USB_MUSB_DSPS -#define CONFIG_USB_MUSB_PIO_ONLY #define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT #define CONFIG_AM335X_USB0 diff --git a/include/configs/sniper.h b/include/configs/sniper.h index 5809942..09b5a73 100644 --- a/include/configs/sniper.h +++ b/include/configs/sniper.h @@ -113,8 +113,6 @@ * USB gadget */ -#define CONFIG_USB_MUSB_PIO_ONLY -#define CONFIG_USB_MUSB_OMAP2PLUS #define CONFIG_TWL4030_USB /* diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h index 3855c56..582aba2 100644 --- a/include/configs/sunxi-common.h +++ b/include/configs/sunxi-common.h @@ -302,10 +302,6 @@ extern int soft_i2c_gpio_scl; #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 1 #endif -#ifdef CONFIG_USB_MUSB_SUNXI -#define CONFIG_USB_MUSB_PIO_ONLY -#endif - #ifdef CONFIG_USB_MUSB_GADGET #define CONFIG_USB_FUNCTION_MASS_STORAGE #endif diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 43a4ff0..7ff11c5 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -4943,12 +4943,8 @@ CONFIG_USB_HOST_XHCI_BASE CONFIG_USB_INVENTRA_DMA CONFIG_USB_ISP1301_I2C_ADDR CONFIG_USB_MAX_CONTROLLER_COUNT -CONFIG_USB_MUSB_AM35X CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT -CONFIG_USB_MUSB_DSPS CONFIG_USB_MUSB_HCD -CONFIG_USB_MUSB_OMAP2PLUS -CONFIG_USB_MUSB_PIO_ONLY CONFIG_USB_MUSB_TIMEOUT CONFIG_USB_MUSB_TUSB6010 CONFIG_USB_MUSB_UDC -- 2.7.4

6 8

[U-Boot] [PATCH] ARM: omap3_logic: Enable SPL_OF_CONTROL and SPL_OF_PLATDATA
by Adam Ford 23 Jan '18

23 Jan '18

The SPL doesn't have much room, so in order to support OF_CONTROL in SPL, we need the extra functionality of SPL_OF_PLATDATA. Adding these features allows us to remove a small part of code without losing the serial port during SPL. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/board/logicpd/omap3som/omap3logic.c b/board/logicpd/omap3som/omap3logic.c index b30fa24..4cbbf96 100644 --- a/board/logicpd/omap3som/omap3logic.c +++ b/board/logicpd/omap3som/omap3logic.c @@ -40,21 +40,6 @@ DECLARE_GLOBAL_DATA_PTR; -/* This is only needed until SPL gets OF support */ -#ifdef CONFIG_SPL_BUILD -static const struct ns16550_platdata omap3logic_serial = { - .base = OMAP34XX_UART1, - .reg_shift = 2, - .clock = V_NS16550_CLK, - .fcr = UART_FCR_DEFVAL, -}; - -U_BOOT_DEVICE(omap3logic_uart) = { - "ns16550_serial", - &omap3logic_serial -}; -#endif - /* * two dimensional array of strucures containining board name and Linux * machine IDs; row it selected based on CPU column is slected based diff --git a/configs/omap3_logic_defconfig b/configs/omap3_logic_defconfig index db72e6f..5590b9a 100644 --- a/configs/omap3_logic_defconfig +++ b/configs/omap3_logic_defconfig @@ -29,6 +29,8 @@ CONFIG_MTDPARTS_DEFAULT="mtdparts=omap2-nand.0:512k(MLO),1792k(u-boot),128k(spl- CONFIG_CMD_UBI=y CONFIG_ISO_PARTITION=y CONFIG_OF_CONTROL=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_SPL_OF_PLATDATA=y CONFIG_ENV_IS_IN_NAND=y # CONFIG_BLK is not set CONFIG_DM_I2C=y @@ -56,3 +58,4 @@ CONFIG_USB_GADGET_VENDOR_NUM=0x0451 CONFIG_USB_GADGET_PRODUCT_NUM=0xd022 CONFIG_USB_ETHER=y CONFIG_BCH=y +# CONFIG_SPL_OF_LIBFDT is not set -- 2.7.4

2 1