August 2015 - U-Boot

[U-Boot] [PATCH v3 0/6] net: Move e1000 driver to driver model and Kconfig
by Simon Glass 13 Aug '15

13 Aug '15

1 6

[U-Boot] [PATCH v6 5/5] usb: lpc32xx: add host USB driver
by slemieux.tyco＠gmail.com 13 Aug '15

13 Aug '15

From: Sylvain Lemieux <slemieux(a)tycoint.com> Incorporate USB driver from legacy LPCLinux NXP BSP. The files taken from the legacy patch are: - lpc32xx USB driver - lpc3250 header file USB registers definition. The legacy driver was updated and clean-up as part of the integration with the latest u-boot. Signed-off-by: Sylvain Lemieux <slemieux(a)tycoint.com> --- Changes from v5 to v6: * Addressed Marek's comments on LPC32xx USB driver: - return "-ETIMEDOUT" on timeout. * Addressed Vladimir's comments on LPC32xx USB driver: - follow alphabetic order when adding "lpc32xx_usb_init()". - use "CONFIG_SYS_HZ" when verifying if timer expired. - use "wait_for_bit()" when verify the I2C OTG clock status. Changes from v4 to v5: * Addressed Marek's comments on LPC32xx USB driver: - update "wait_for_bit()" implementation to use "get_timer()". - use return value of "wait_for_bit()" instead of returning -1. * Updated multiline comments style. Changes from v3 to v4: * Addressed Marek's comments on LPC32xx USB driver: - use same "wait_for_bit()" implementation as drivers/usb/host/dwc2.c - use a const variable to define a mask to make the code more clear to read. * Fixed legacy USB driver; use "otg_clk_sts" register to verify clock status instead of control register. Changes from v2 to v3: * Addressed Marek's comments on LPC32xx USB driver: - use "get_timer()" to handle timeout (usbpll_setup). - submit i2c driver update into a separate patch. - use "u32" for 4 bytes registers definition. - Move pin mux code to setup file (i.e. "device.c"). * Updated ISP1301 register definition (set & clear) instead of using an extra mask for the clear address. Changes from v1 to v2: * Addressed Marek's comments on LPC32xx USB driver: - use "get_timer()" to handle timeout. - Split USB and I2C driver. * Updated LPC32xx I2C driver to support the I2C that is part of the USB module. * Removed ISP1301 USB transceiver I2C registers definition that are not used. * Use "cpu" initialization & stop functions API instead of the "board" API. Update to the legacy driver to integrate with the latest u-boot: 1) Fixed checkpatch script output in legacy code. 2) Use LPC32xx definition from "cpu.h" and "clk.h". 3) Incorporate USB specific register definition from "lpc3250.h" header file from legacy BSP patch from LPCLinux. 4) Use u-boot API for register access to remove the volatile in register definition taken from "lpc3250.h" header file. 5) Update driver for latest u-boot USB API. 6) Use the peripheral clock to compute the I2C divider. The legacy BSP patch (u-boot-2009.03_lpc32x0-v1.07.patch.tar.bz2) was downloaded from the LPCLinux Web site. arch/arm/cpu/arm926ejs/lpc32xx/devices.c | 6 + arch/arm/include/asm/arch-lpc32xx/clk.h | 12 ++ arch/arm/include/asm/arch-lpc32xx/sys_proto.h | 1 + drivers/usb/host/Makefile | 1 + drivers/usb/host/ohci-lpc32xx.c | 235 ++++++++++++++++++++++++++ 5 files changed, 255 insertions(+) create mode 100644 drivers/usb/host/ohci-lpc32xx.c diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/devices.c b/arch/arm/cpu/arm926ejs/lpc32xx/devices.c index f0af851..d9fa280 100644 --- a/arch/arm/cpu/arm926ejs/lpc32xx/devices.c +++ b/arch/arm/cpu/arm926ejs/lpc32xx/devices.c @@ -72,6 +72,12 @@ void lpc32xx_slc_nand_init(void) writel(CLK_NAND_SLC | CLK_NAND_SLC_SELECT, &clk->flashclk_ctrl); } +void lpc32xx_usb_init(void) +{ + /* Do not route the UART 5 Tx/Rx pins to the USB D+ and USB D- pins. */ + clrbits_le32(&ctrl->ctrl, UART_CTRL_UART5_USB_MODE); +} + void lpc32xx_i2c_init(unsigned int devnum) { /* Enable I2C interface */ diff --git a/arch/arm/include/asm/arch-lpc32xx/clk.h b/arch/arm/include/asm/arch-lpc32xx/clk.h index 663f6bc..d21310e 100644 --- a/arch/arm/include/asm/arch-lpc32xx/clk.h +++ b/arch/arm/include/asm/arch-lpc32xx/clk.h @@ -167,6 +167,18 @@ struct clk_pm_regs { /* SDRAMCLK register bits */ #define CLK_SDRAM_DDR_SEL (1 << 1) +/* USB control register definitions */ +#define CLK_USBCTRL_PLL_STS (1 << 0) +#define CLK_USBCTRL_FDBK_PLUS1(n) (((n) & 0xFF) << 1) +#define CLK_USBCTRL_POSTDIV_2POW(n) (((n) & 0x3) << 11) +#define CLK_USBCTRL_PLL_PWRUP (1 << 16) +#define CLK_USBCTRL_CLK_EN1 (1 << 17) +#define CLK_USBCTRL_CLK_EN2 (1 << 18) +#define CLK_USBCTRL_BUS_KEEPER (0x1 << 19) +#define CLK_USBCTRL_USBHSTND_EN (1 << 21) +#define CLK_USBCTRL_USBDVND_EN (1 << 22) +#define CLK_USBCTRL_HCLK_EN (1 << 24) + unsigned int get_sys_clk_rate(void); unsigned int get_hclk_pll_rate(void); unsigned int get_hclk_clk_div(void); diff --git a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h index d6e5e68..eb8010f 100644 --- a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h +++ b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h @@ -16,6 +16,7 @@ void lpc32xx_mlc_nand_init(void); void lpc32xx_slc_nand_init(void); void lpc32xx_i2c_init(unsigned int devnum); void lpc32xx_ssp_init(void); +void lpc32xx_usb_init(void); #if defined(CONFIG_SPL_BUILD) void ddr_init(const struct emc_dram_settings *dram); #endif diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 4d35d3e..9dfdc94 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -20,6 +20,7 @@ obj-$(CONFIG_USB_SL811HS) += sl811-hcd.o obj-$(CONFIG_USB_OHCI_S3C24XX) += ohci-s3c24xx.o obj-$(CONFIG_USB_OHCI_EP93XX) += ohci-ep93xx.o obj-$(CONFIG_USB_OHCI_SUNXI) += ohci-sunxi.o +obj-$(CONFIG_USB_OHCI_LPC32XX) += ohci-lpc32xx.o # echi obj-$(CONFIG_USB_EHCI) += ehci-hcd.o diff --git a/drivers/usb/host/ohci-lpc32xx.c b/drivers/usb/host/ohci-lpc32xx.c new file mode 100644 index 0000000..acf356b --- /dev/null +++ b/drivers/usb/host/ohci-lpc32xx.c @@ -0,0 +1,235 @@ +/* + * Copyright (C) 2008 by NXP Semiconductors + * @Author: Based on code by Kevin Wells + * @Descr: USB driver - Embedded Artists LPC3250 OEM Board support functions + * + * Copyright (c) 2015 Tyco Fire Protection Products. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <errno.h> +#include <asm/io.h> +#include <asm/arch/cpu.h> +#include <asm/arch/clk.h> +#include <usb.h> +#include <i2c.h> + +/* OTG I2C controller module register structures */ +struct otgi2c_regs { + u32 otg_i2c_txrx; /* OTG I2C Tx/Rx Data FIFO */ + u32 otg_i2c_stat; /* OTG I2C Status Register */ + u32 otg_i2c_ctrl; /* OTG I2C Control Register */ + u32 otg_i2c_clk_hi; /* OTG I2C Clock Divider high */ + u32 otg_i2c_clk_lo; /* OTG I2C Clock Divider low */ +}; + +/* OTG controller module register structures */ +struct otg_regs { + u32 reserved1[64]; + u32 otg_int_sts; /* OTG int status register */ + u32 otg_int_enab; /* OTG int enable register */ + u32 otg_int_set; /* OTG int set register */ + u32 otg_int_clr; /* OTG int clear register */ + u32 otg_sts_ctrl; /* OTG status/control register */ + u32 otg_timer; /* OTG timer register */ + u32 reserved2[122]; + struct otgi2c_regs otg_i2c; + u32 reserved3[824]; + u32 otg_clk_ctrl; /* OTG clock control reg */ + u32 otg_clk_sts; /* OTG clock status reg */ +}; + +/* otg_sts_ctrl register definitions */ +#define OTG_HOST_EN (1 << 0) /* Enable host mode */ + +/* otg_clk_ctrl and otg_clk_sts register definitions */ +#define OTG_CLK_AHB_EN (1 << 4) /* Enable AHB clock */ +#define OTG_CLK_OTG_EN (1 << 3) /* Enable OTG clock */ +#define OTG_CLK_I2C_EN (1 << 2) /* Enable I2C clock */ +#define OTG_CLK_HOST_EN (1 << 0) /* Enable host clock */ + +/* ISP1301 USB transceiver I2C registers */ +#define MC1_SPEED_REG (1 << 0) +#define MC1_DAT_SE0 (1 << 2) +#define MC1_UART_EN (1 << 6) + +#define MC2_SPD_SUSP_CTRL (1 << 1) +#define MC2_BI_DI (1 << 2) +#define MC2_PSW_EN (1 << 6) + +#define OTG1_DP_PULLUP (1 << 0) +#define OTG1_DM_PULLUP (1 << 1) +#define OTG1_DP_PULLDOWN (1 << 2) +#define OTG1_DM_PULLDOWN (1 << 3) +#define OTG1_VBUS_DRV (1 << 5) + +#define ISP1301_I2C_ADDR CONFIG_USB_ISP1301_I2C_ADDR + +#define ISP1301_I2C_MODE_CONTROL_1_SET 0x04 +#define ISP1301_I2C_MODE_CONTROL_1_CLR 0x05 +#define ISP1301_I2C_MODE_CONTROL_2_SET 0x12 +#define ISP1301_I2C_MODE_CONTROL_2_CLR 0x13 +#define ISP1301_I2C_OTG_CONTROL_1_SET 0x06 +#define ISP1301_I2C_OTG_CONTROL_1_CLR 0x07 +#define ISP1301_I2C_INTERRUPT_LATCH_CLR 0x0B +#define ISP1301_I2C_INTERRUPT_FALLING_CLR 0x0D +#define ISP1301_I2C_INTERRUPT_RISING_CLR 0x0F + +static struct otg_regs *otg = (struct otg_regs *)USB_BASE; +static struct clk_pm_regs *clk_pwr = (struct clk_pm_regs *)CLK_PM_BASE; + +static int wait_for_bit(void *reg, const u32 mask, bool set) +{ + u32 val; + unsigned long start = get_timer(0); + + while (1) { + val = readl(reg); + if (!set) + val = ~val; + + if ((val & mask) == mask) + return 0; + + if (get_timer(start) > CONFIG_SYS_HZ) + break; + + udelay(1); + } + + debug("%s: Timeout (reg=%p mask=%08x wait_set=%i)\n", + __func__, reg, mask, set); + + return -ETIMEDOUT; +} + +static int isp1301_set_value(int reg, u8 value) +{ + return i2c_write(ISP1301_I2C_ADDR, reg, 1, &value, 1); +} + +static void isp1301_configure(void) +{ + i2c_set_bus_num(I2C_2); + + /* + * LPC32XX only supports DAT_SE0 USB mode + * This sequence is important + */ + + /* Disable transparent UART mode first */ + isp1301_set_value(ISP1301_I2C_MODE_CONTROL_1_CLR, MC1_UART_EN); + + isp1301_set_value(ISP1301_I2C_MODE_CONTROL_1_CLR, ~MC1_SPEED_REG); + isp1301_set_value(ISP1301_I2C_MODE_CONTROL_1_SET, MC1_SPEED_REG); + isp1301_set_value(ISP1301_I2C_MODE_CONTROL_2_CLR, ~0); + isp1301_set_value(ISP1301_I2C_MODE_CONTROL_2_SET, + MC2_BI_DI | MC2_PSW_EN | MC2_SPD_SUSP_CTRL); + + isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_CLR, ~0); + isp1301_set_value(ISP1301_I2C_MODE_CONTROL_1_SET, MC1_DAT_SE0); + isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_SET, + OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN); + isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_CLR, + OTG1_DM_PULLUP | OTG1_DP_PULLUP); + isp1301_set_value(ISP1301_I2C_INTERRUPT_LATCH_CLR, ~0); + isp1301_set_value(ISP1301_I2C_INTERRUPT_FALLING_CLR, ~0); + isp1301_set_value(ISP1301_I2C_INTERRUPT_RISING_CLR, ~0); + + /* Enable usb_need_clk clock after transceiver is initialized */ + setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_USBDVND_EN); +} + +static int usbpll_setup(void) +{ + u32 ret; + + /* make sure clocks are disabled */ + clrbits_le32(&clk_pwr->usb_ctrl, + CLK_USBCTRL_CLK_EN1 | CLK_USBCTRL_CLK_EN2); + + /* start PLL clock input */ + setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_CLK_EN1); + + /* Setup PLL. */ + setbits_le32(&clk_pwr->usb_ctrl, + CLK_USBCTRL_FDBK_PLUS1(192 - 1)); + setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_POSTDIV_2POW(0x01)); + setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_PLL_PWRUP); + + ret = wait_for_bit(&clk_pwr->usb_ctrl, CLK_USBCTRL_PLL_STS, 1); + if (ret) + return ret; + + /* enable PLL output */ + setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_CLK_EN2); + + return 0; +} + +int usb_cpu_init(void) +{ + u32 ret; + + /* + * USB pins routing setup is done by "lpc32xx_usb_init()" and should + * be call by board "board_init()" or "misc_init_r()" functions. + */ + + /* enable AHB slave USB clock */ + setbits_le32(&clk_pwr->usb_ctrl, + CLK_USBCTRL_HCLK_EN | CLK_USBCTRL_BUS_KEEPER); + + /* enable I2C clock in OTG block if it isn't */ + if ((readl(&otg->otg_clk_sts) & OTG_CLK_I2C_EN) != OTG_CLK_I2C_EN) { + writel(OTG_CLK_I2C_EN, &otg->otg_clk_ctrl); + + ret = wait_for_bit(&otg->otg_clk_sts, OTG_CLK_I2C_EN, 1); + if (ret) + return ret; + } + + /* Configure ISP1301 */ + isp1301_configure(); + + /* setup USB clocks and PLL */ + ret = usbpll_setup(); + if (ret) + return ret; + + /* enable usb_host_need_clk */ + setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_USBHSTND_EN); + + /* enable all needed USB clocks */ + const u32 mask = OTG_CLK_AHB_EN | OTG_CLK_OTG_EN | + OTG_CLK_I2C_EN | OTG_CLK_HOST_EN; + writel(mask, &otg->otg_clk_ctrl); + + ret = wait_for_bit(&otg->otg_clk_sts, mask, 1); + if (ret) + return ret; + + setbits_le32(&otg->otg_sts_ctrl, OTG_HOST_EN); + isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_SET, OTG1_VBUS_DRV); + + return 0; +} + +int usb_cpu_stop(void) +{ + /* vbus off */ + isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_SET, OTG1_VBUS_DRV); + + clrbits_le32(&otg->otg_sts_ctrl, OTG_HOST_EN); + + clrbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_HCLK_EN); + + return 0; +} + +int usb_cpu_init_fail(void) +{ + return usb_cpu_stop(); +} -- 1.8.3.1

4 11

[U-Boot] [PATCH 1/4] x86: microcode-tool: Write pure data to the dtsi file
by Bin Meng 13 Aug '15

13 Aug '15

Currently the microcode-tool writes microcode into a data block as well as the device tree properties which represents the first 48 bytes in the microcode data. Now we change the tool to only write the microcode without device tree stuff so that multiple microcode data blocks can be included in a single property. Signed-off-by: Bin Meng <bmeng.cn(a)gmail.com> --- tools/microcode-tool.py | 23 ++++++++++++----------- 1 file changed, 12 insertions(+), 11 deletions(-) diff --git a/tools/microcode-tool.py b/tools/microcode-tool.py index 71c2e91..5522ffc 100755 --- a/tools/microcode-tool.py +++ b/tools/microcode-tool.py @@ -173,20 +173,21 @@ def CreateFile(date, license_text, mcodes, outfile): * node. * * Date: %s + * + * Device tree properties for this microcode: + * + * compatible = "intel,microcode"; + * intel,header-version = <%d>; + * intel,update-revision = <%#x>; + * intel,date-code = <%#x>; + * intel,processor-signature = <%#x>; + * intel,checksum = <%#x>; + * intel,loader-revision = <%d>; + * intel,processor-flags = <%#x>; */ -compatible = "intel,microcode"; -intel,header-version = <%d>; -intel,update-revision = <%#x>; -intel,date-code = <%#x>; -intel,processor-signature = <%#x>; -intel,checksum = <%#x>; -intel,loader-revision = <%d>; -intel,processor-flags = <%#x>; - /* The first 48-bytes are the public header which repeats the above data */ -data = <%s -\t>;''' +%s''' words = '' add_comments = len(mcodes) > 1 for mcode in mcodes: -- 1.8.2.1

3 18

[U-Boot] [U-BOOT PATCH v3 0/4] x86: This series adds ACPI support for qemu targets.
by Saket Sinha 13 Aug '15

13 Aug '15

ACPI(Advanced Configuration and Power Interface), a Power Management and configuration standard allowing the operating system to control the amount of power each device is given (allowing it to put certain devices on standby or power-off for example). It is also used to control and/or check thermal zones (temperature sensors, fan speeds, etc), battery levels, PCI IRQ routing, CPUs, NUMA domains and many other things. To begin using ACPI, the operating system must look for the RSDP (Root System Description Pointer). If the RSDP is found, the verification is valid, it contains a pointer to the RSDT (Root System Description Table) and XSDT (extended System Description Table). For the run time part of ACPI the main table to detect is the FADT (Fixed ACPI Description Table) as this contains information needed to enable ACPI. The DSDT table contains a bytecode that is executed by a driver in the kernel. Changes from v2: - Fixes issues with using MMCONFIG for q35. - Fixes various entries in ACPI tables that OS was not able to parse. Changes from v1: - Dynamic generation of AML code for DSDT table. -Reading PCI registers for FADT table. -Incorporated review comments. Saket Sinha (4): x86: Added ACPI support as a configuration option. x86: Added support for ACPI table generation at the generic layer. x86: Added ACPI support for Qemu. x86: Added dsdt tables for Qemu ACPI implementation. arch/x86/Kconfig | 6 + arch/x86/cpu/qemu/Makefile | 3 +- arch/x86/cpu/qemu/acpi.c | 157 ++++++++++++ arch/x86/cpu/qemu/acpi/cpu-hotplug.asl | 78 ++++++ arch/x86/cpu/qemu/acpi/dbug.asl | 26 ++ arch/x86/cpu/qemu/acpi/hpet.asl | 36 +++ arch/x86/cpu/qemu/acpi/isa.asl | 102 ++++++++ arch/x86/cpu/qemu/acpi/pci-crs.asl | 94 +++++++ arch/x86/cpu/qemu/dsdt.asl | 440 +++++++++++++++++++++++++++++++++ arch/x86/include/asm/acpi_table.h | 387 +++++++++++++++++++++++++++++ arch/x86/lib/Makefile | 1 + arch/x86/lib/acpi_table.c | 413 +++++++++++++++++++++++++++++++ arch/x86/lib/tables.c | 5 + scripts/Makefile.lib | 11 + 14 files changed, 1758 insertions(+), 1 deletion(-) create mode 100644 arch/x86/cpu/qemu/acpi.c create mode 100644 arch/x86/cpu/qemu/acpi/cpu-hotplug.asl create mode 100644 arch/x86/cpu/qemu/acpi/dbug.asl create mode 100644 arch/x86/cpu/qemu/acpi/hpet.asl create mode 100644 arch/x86/cpu/qemu/acpi/isa.asl create mode 100644 arch/x86/cpu/qemu/acpi/pci-crs.asl create mode 100644 arch/x86/cpu/qemu/dsdt.asl create mode 100644 arch/x86/include/asm/acpi_table.h create mode 100644 arch/x86/lib/acpi_table.c -- 2.1.4

2 9

[U-Boot] GCC 5.2 issue on imx28
by Otavio Salvador 13 Aug '15

13 Aug '15

Hello folks, OE-Core is preparing for upgrade to GCC 5.2 as default compiler and mx28 is failing[1] to build with it. 1. http://errors.yoctoproject.org/Errors/Details/13878/ I am not a linker guy so could someone shed any light on this? -- Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750

5 8

[U-Boot] [PATCH 0/2] configs: ti_armv7_keystone2: fix default args_ramfs
by Vitaly Andrianov 13 Aug '15

13 Aug '15

This series fixes couple of bugs in default args_ramfs environment variable Vitaly Andrianov (2): configs: ti_armv7_keystone2: fix initrd address at args_ramfs configs: ti_armv7_keystone2: increase size reserved for initrd include/configs/ti_armv7_keystone2.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) -- 1.9.1

2 7

[U-Boot] [RESEND PATCH v5] fs/fs.c: read up to EOF when len would read past EOF
by Marcel Ziswiler 13 Aug '15

13 Aug '15

From: Max Krummenacher <max.krummenacher(a)toradex.com> http://lists.denx.de/pipermail/u-boot/2012-September/134347.html allows for reading files in chunks from the shell. When this feature is used to read past the end of a file an error was returned instead of returning the bytes read up to the end of file. Thus the following fails in the shell: offset = 0 len = chunksize do read file, offset, len write data until bytes_read < len The patch changes the behaviour to printing an informational message and returning the actual read number of bytes aka read(2) behaviour for convenient use in U-Boot scripts. Signed-off-by: Max Krummenacher <max.krummenacher(a)toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler(a)toradex.com> Acked-by: Marek Vasut <marex(a)denx.de> --- Changes in v5: split up into separate patches to be picked up by the various subsystem maintainers as suggested by Marek Changes in v2: mention read(2) behaviour as suggested by Marek fs/fs.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/fs/fs.c b/fs/fs.c index ac0897d..827b143 100644 --- a/fs/fs.c +++ b/fs/fs.c @@ -301,10 +301,8 @@ int fs_read(const char *filename, ulong addr, loff_t offset, loff_t len, unmap_sysmem(buf); /* If we requested a specific number of bytes, check we got it */ - if (ret == 0 && len && *actread != len) { - printf("** Unable to read file %s **\n", filename); - ret = -1; - } + if (ret == 0 && len && *actread != len) + printf("** %s shorter than offset + len **\n", filename); fs_close(); return ret; -- 2.4.3

4 17

[U-Boot] [RESEND PATCH] common/lcd_console: fix console/logo regression
by Marcel Ziswiler 13 Aug '15

13 Aug '15

From: Marcel Ziswiler <marcel.ziswiler(a)toradex.com> The following commit changed the order of the column vs. row parameter to the lcd_init_console() function but missed actually changing it as well the second time it is called from lcd_clear() which resulted in a garbled text console which this patch fixes. commit 604c7d4a5a3cf70949f6e6094bf0d52ee3b4804d common/lcd_console: introduce display/framebuffer rotation Tested on Colibri T20 with my latest assortment of tegra fixes/enhancements patch set. Signed-off-by: Marcel Ziswiler <marcel.ziswiler(a)toradex.com> --- common/lcd.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/common/lcd.c b/common/lcd.c index 5a52fe4..d29308a 100644 --- a/common/lcd.c +++ b/common/lcd.c @@ -234,8 +234,8 @@ void lcd_clear(void) lcd_logo(); #if defined(CONFIG_LCD_LOGO) && !defined(CONFIG_LCD_INFO_BELOW_LOGO) addr = (ulong)lcd_base + BMP_LOGO_HEIGHT * lcd_line_length; - lcd_init_console((void *)addr, panel_info.vl_row, - panel_info.vl_col, panel_info.vl_rot); + lcd_init_console((void *)addr, panel_info.vl_col, + panel_info.vl_row, panel_info.vl_rot); #endif lcd_sync(); } -- 2.4.3

4 4

[U-Boot] [PATCH] ARM: drop "optional" from target select in favor of ARCH_VERSATILE
by Masahiro Yamada 13 Aug '15

13 Aug '15

Since commit a26cd04920dc ("arch: Make board selection choices optional"), Kconfig could create such an insane .config file that no SoC/board is selected. This is now a real problem for Buildroot, for example. (http://lists.busybox.net/pipermail/buildroot/2015-July/135125.html) This commit drops the "optional" from the ARM target select menu in favor of "Versatile family". Rationale: - Historically, Linux chose versatile_defconfig as the default of ARM defconfig. (arch/arm/Makefile of Linux describes: KBUILD_DEFCONFIG := versatile_defconfig) - It was published by ARM Ltd. Signed-off-by: Masahiro Yamada <yamada.masahiro(a)socionext.com> --- arch/arm/Kconfig | 2 +- configs/versatileab_defconfig | 1 - configs/versatilepb_defconfig | 1 - configs/versatileqemu_defconfig | 1 - 4 files changed, 1 insertion(+), 4 deletions(-) diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 9127ace..5caa23e 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -64,7 +64,7 @@ config SEMIHOSTING choice prompt "Target select" - optional + default ARCH_VERSATILE config ARCH_AT91 bool "Atmel AT91" diff --git a/configs/versatileab_defconfig b/configs/versatileab_defconfig index 765fe6e..3dc7d19 100644 --- a/configs/versatileab_defconfig +++ b/configs/versatileab_defconfig @@ -1,5 +1,4 @@ CONFIG_ARM=y -CONFIG_ARCH_VERSATILE=y CONFIG_SYS_EXTRA_OPTIONS="ARCH_VERSATILE_AB" # CONFIG_CMD_CONSOLE is not set # CONFIG_CMD_BOOTD is not set diff --git a/configs/versatilepb_defconfig b/configs/versatilepb_defconfig index 1973c38..9fe83b9 100644 --- a/configs/versatilepb_defconfig +++ b/configs/versatilepb_defconfig @@ -1,5 +1,4 @@ CONFIG_ARM=y -CONFIG_ARCH_VERSATILE=y CONFIG_SYS_EXTRA_OPTIONS="ARCH_VERSATILE_PB" # CONFIG_CMD_CONSOLE is not set # CONFIG_CMD_BOOTD is not set diff --git a/configs/versatileqemu_defconfig b/configs/versatileqemu_defconfig index ea9c5b9..9ddef4d 100644 --- a/configs/versatileqemu_defconfig +++ b/configs/versatileqemu_defconfig @@ -1,5 +1,4 @@ CONFIG_ARM=y -CONFIG_ARCH_VERSATILE=y CONFIG_SYS_EXTRA_OPTIONS="ARCH_VERSATILE_QEMU,ARCH_VERSATILE_PB" # CONFIG_CMD_CONSOLE is not set # CONFIG_CMD_BOOTD is not set -- 1.9.1

3 2

[U-Boot] [PATCH 1/5] am33xx: Update DT files, add am335x_gp_evm_config target
by Tom Rini 13 Aug '15

13 Aug '15

- Re-sync DT files for am33xx with Linux Kernel v4.1 - Include DT file now for the "AM335x GP EVM" and build target for it, via device tree and DM. - We only need to provide platform data for UART when OF_CONTROL isn't also enabled really. We can just push GPIO to coming from DT Signed-off-by: Tom Rini <trini(a)konsulko.com> --- arch/arm/cpu/armv7/am33xx/board.c | 36 +- arch/arm/dts/Makefile | 2 +- arch/arm/dts/am335x-bone-common.dtsi | 410 +++++++++++------- arch/arm/dts/am335x-bone.dts | 29 ++ arch/arm/dts/am335x-boneblack.dts | 72 ++++ arch/arm/dts/am335x-evm.dts | 765 ++++++++++++++++++++++++++++++++++ arch/arm/dts/am33xx-clocks.dtsi | 646 ++++++++++++++++++++++++++++ arch/arm/dts/am33xx.dtsi | 297 +++++++++++-- arch/arm/dts/tps65910.dtsi | 91 ++++ configs/am335x_gp_evm_defconfig | 14 + 10 files changed, 2156 insertions(+), 206 deletions(-) create mode 100644 arch/arm/dts/am335x-bone.dts create mode 100644 arch/arm/dts/am335x-evm.dts create mode 100644 arch/arm/dts/am33xx-clocks.dtsi create mode 100644 arch/arm/dts/tps65910.dtsi create mode 100644 configs/am335x_gp_evm_defconfig diff --git a/arch/arm/cpu/armv7/am33xx/board.c b/arch/arm/cpu/armv7/am33xx/board.c index 67bef23..81492a5 100644 --- a/arch/arm/cpu/armv7/am33xx/board.c +++ b/arch/arm/cpu/armv7/am33xx/board.c @@ -38,45 +38,22 @@ DECLARE_GLOBAL_DATA_PTR; -#ifdef CONFIG_DM_GPIO -static const struct omap_gpio_platdata am33xx_gpio[] = { - { 0, AM33XX_GPIO0_BASE, METHOD_GPIO_24XX }, - { 1, AM33XX_GPIO1_BASE, METHOD_GPIO_24XX }, - { 2, AM33XX_GPIO2_BASE, METHOD_GPIO_24XX }, - { 3, AM33XX_GPIO3_BASE, METHOD_GPIO_24XX }, -#ifdef CONFIG_AM43XX - { 4, AM33XX_GPIO4_BASE, METHOD_GPIO_24XX }, - { 5, AM33XX_GPIO5_BASE, METHOD_GPIO_24XX }, -#endif -}; - -U_BOOT_DEVICES(am33xx_gpios) = { - { "gpio_omap", &am33xx_gpio[0] }, - { "gpio_omap", &am33xx_gpio[1] }, - { "gpio_omap", &am33xx_gpio[2] }, - { "gpio_omap", &am33xx_gpio[3] }, -#ifdef CONFIG_AM43XX - { "gpio_omap", &am33xx_gpio[4] }, - { "gpio_omap", &am33xx_gpio[5] }, -#endif -}; - -# ifndef CONFIG_OF_CONTROL +#if defined(CONFIG_DM_SERIAL) && !defined(CONFIG_OF_CONTROL) /* * TODO(sjg(a)chromium.org): When we can move SPL serial to DM, we can remove * the CONFIGs. At the same time, we should move this to the board files. */ static const struct ns16550_platdata am33xx_serial[] = { { CONFIG_SYS_NS16550_COM1, 2, CONFIG_SYS_NS16550_CLK }, -# ifdef CONFIG_SYS_NS16550_COM2 +# ifdef CONFIG_SYS_NS16550_COM2 { CONFIG_SYS_NS16550_COM2, 2, CONFIG_SYS_NS16550_CLK }, -# ifdef CONFIG_SYS_NS16550_COM3 +# ifdef CONFIG_SYS_NS16550_COM3 { CONFIG_SYS_NS16550_COM3, 2, CONFIG_SYS_NS16550_CLK }, { CONFIG_SYS_NS16550_COM4, 2, CONFIG_SYS_NS16550_CLK }, { CONFIG_SYS_NS16550_COM5, 2, CONFIG_SYS_NS16550_CLK }, { CONFIG_SYS_NS16550_COM6, 2, CONFIG_SYS_NS16550_CLK }, -# endif # endif +# endif }; U_BOOT_DEVICES(am33xx_uarts) = { @@ -91,10 +68,10 @@ U_BOOT_DEVICES(am33xx_uarts) = { # endif # endif }; -# endif +#endif -#else +#ifndef CONFIG_DM_GPIO static const struct gpio_bank gpio_bank_am33xx[] = { { (void *)AM33XX_GPIO0_BASE, METHOD_GPIO_24XX }, { (void *)AM33XX_GPIO1_BASE, METHOD_GPIO_24XX }, @@ -107,7 +84,6 @@ static const struct gpio_bank gpio_bank_am33xx[] = { }; const struct gpio_bank *const omap_gpio_bank = gpio_bank_am33xx; - #endif #if defined(CONFIG_OMAP_HSMMC) && !defined(CONFIG_SPL_BUILD) diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index ba63553..43b1616 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -49,7 +49,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \ zynq-zc770-xm011.dtb \ zynq-zc770-xm012.dtb \ zynq-zc770-xm013.dtb -dtb-$(CONFIG_AM33XX) += am335x-boneblack.dtb +dtb-$(CONFIG_AM33XX) += am335x-boneblack.dtb am335x-evm.dtb dtb-$(CONFIG_ARCH_SOCFPGA) += \ socfpga_arria5_socdk.dtb \ diff --git a/arch/arm/dts/am335x-bone-common.dtsi b/arch/arm/dts/am335x-bone-common.dtsi index e70b4d1..fec7834 100644 --- a/arch/arm/dts/am335x-bone-common.dtsi +++ b/arch/arm/dts/am335x-bone-common.dtsi @@ -7,13 +7,6 @@ */ / { - model = "TI AM335x BeagleBone"; - compatible = "ti,am335x-bone", "ti,am33xx"; - - chosen { - stdout-path = &uart0; - }; - cpus { cpu@0 { cpu0-supply = <&dcdc2_reg>; @@ -25,184 +18,299 @@ reg = <0x80000000 0x10000000>; /* 256 MB */ }; - am33xx_pinmux: pinmux@44e10800 { + leds { pinctrl-names = "default"; - pinctrl-0 = <&clkout2_pin>; - - user_leds_s0: user_leds_s0 { - pinctrl-single,pins = < - 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ - 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */ - 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ - 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */ - >; - }; + pinctrl-0 = <&user_leds_s0>; - i2c0_pins: pinmux_i2c0_pins { - pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ - >; - }; + compatible = "gpio-leds"; - uart0_pins: pinmux_uart0_pins { - pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ - >; + led@2 { + label = "beaglebone:green:heartbeat"; + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; }; - clkout2_pin: pinmux_clkout2_pin { - pinctrl-single,pins = < - 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ - >; + led@3 { + label = "beaglebone:green:mmc0"; + gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; }; - cpsw_default: cpsw_default { - pinctrl-single,pins = < - /* Slave 1 */ - 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */ - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */ - 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */ - 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */ - 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */ - 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */ - 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */ - 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */ - 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */ - 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */ - 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */ - >; + led@4 { + label = "beaglebone:green:usr2"; + gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "cpu0"; + default-state = "off"; }; - cpsw_sleep: cpsw_sleep { - pinctrl-single,pins = < - /* Slave 1 reset value */ - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) - >; + led@5 { + label = "beaglebone:green:usr3"; + gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; }; + }; - davinci_mdio_default: davinci_mdio_default { - pinctrl-single,pins = < - /* MDIO */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ - >; - }; + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; - davinci_mdio_sleep: davinci_mdio_sleep { - pinctrl-single,pins = < - /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) - >; - }; +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&clkout2_pin>; + + user_leds_s0: user_leds_s0 { + pinctrl-single,pins = < + 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ + 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */ + 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ + 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */ + >; }; - ocp { - uart0: serial@44e09000 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins>; + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; - status = "okay"; - }; + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + 0x178 (PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_ctsn.i2c2_sda */ + 0x17c (PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_rtsn.i2c2_scl */ + >; + }; - musb: usb@47400000 { - status = "okay"; + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; - control@44e10000 { - status = "okay"; - }; + clkout2_pin: pinmux_clkout2_pin { + pinctrl-single,pins = < + 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ + >; + }; - usb-phy@47401300 { - status = "okay"; - }; + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */ + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */ + 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */ + 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */ + 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */ + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */ + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */ + 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */ + 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */ + 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */ + 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */ + 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */ + 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */ + >; + }; - usb-phy@47401b00 { - status = "okay"; - }; + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; - usb@47401000 { - status = "okay"; - }; + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; - usb@47401800 { - status = "okay"; - dr_mode = "host"; - }; + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; - dma-controller@07402000 { - status = "okay"; - }; - }; + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0x160 (PIN_INPUT | MUX_MODE7) /* GPIO0_6 */ + >; + }; + + emmc_pins: pinmux_emmc_pins { + pinctrl-single,pins = < + 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ + 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ + 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ + 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ + >; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; - i2c0: i2c@44e0b000 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins>; + status = "okay"; +}; - status = "okay"; - clock-frequency = <400000>; +&usb { + status = "okay"; +}; - tps: tps@24 { - reg = <0x24>; - }; +&usb_ctrl_mod { + status = "okay"; +}; +&usb0_phy { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb0 { + status = "okay"; + dr_mode = "peripheral"; +}; + +&usb1 { + status = "okay"; + dr_mode = "host"; +}; + +&cppi41dma { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + + tps: tps@24 { + reg = <0x24>; + }; + + baseboard_eeprom: baseboard_eeprom@50 { + compatible = "at,24c256"; + reg = <0x50>; + + #address-cells = <1>; + #size-cells = <1>; + baseboard_data: baseboard_data@0 { + reg = <0 0x100>; }; }; +}; - leds { - pinctrl-names = "default"; - pinctrl-0 = <&user_leds_s0>; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; - compatible = "gpio-leds"; + status = "okay"; + clock-frequency = <100000>; - led@2 { - label = "beaglebone:green:heartbeat"; - gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - default-state = "off"; + cape_eeprom0: cape_eeprom0@54 { + compatible = "at,24c256"; + reg = <0x54>; + #address-cells = <1>; + #size-cells = <1>; + cape0_data: cape_data@0 { + reg = <0 0x100>; }; + }; - led@3 { - label = "beaglebone:green:mmc0"; - gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc0"; - default-state = "off"; + cape_eeprom1: cape_eeprom1@55 { + compatible = "at,24c256"; + reg = <0x55>; + #address-cells = <1>; + #size-cells = <1>; + cape1_data: cape_data@0 { + reg = <0 0x100>; }; + }; - led@4 { - label = "beaglebone:green:usr2"; - gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; - default-state = "off"; + cape_eeprom2: cape_eeprom2@56 { + compatible = "at,24c256"; + reg = <0x56>; + #address-cells = <1>; + #size-cells = <1>; + cape2_data: cape_data@0 { + reg = <0 0x100>; }; + }; - led@5 { - label = "beaglebone:green:usr3"; - gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>; - default-state = "off"; + cape_eeprom3: cape_eeprom3@57 { + compatible = "at,24c256"; + reg = <0x57>; + #address-cells = <1>; + #size-cells = <1>; + cape3_data: cape_data@0 { + reg = <0 0x100>; }; }; }; + /include/ "tps65217.dtsi" &tps { + /* + * Configure pmic to enter OFF-state instead of SLEEP-state ("RTC-only + * mode") at poweroff. Most BeagleBone versions do not support RTC-only + * mode and risk hardware damage if this mode is entered. + * + * For details, see linux-omap mailing list May 2015 thread + * [PATCH] ARM: dts: am335x-bone* enable pmic-shutdown-controller + * In particular, messages: + * http://www.spinics.net/lists/linux-omap/msg118585.html + * http://www.spinics.net/lists/linux-omap/msg118615.html + * + * You can override this later with + * &tps { /delete-property/ ti,pmic-shutdown-controller; } + * if you want to use RTC-only mode and made sure you are not affected + * by the hardware problems. (Tip: double-check by performing a current + * measurement after shutdown: it should be less than 1 mA.) + */ + ti,pmic-shutdown-controller; + regulators { dcdc1_reg: regulator@0 { + regulator-name = "vdds_dpr"; regulator-always-on; }; @@ -225,18 +333,22 @@ }; ldo1_reg: regulator@3 { + regulator-name = "vio,vrtc,vdds"; regulator-always-on; }; ldo2_reg: regulator@4 { + regulator-name = "vdd_3v3aux"; regulator-always-on; }; ldo3_reg: regulator@5 { + regulator-name = "vdd_1v8"; regulator-always-on; }; ldo4_reg: regulator@6 { + regulator-name = "vdd_3v3a"; regulator-always-on; }; }; @@ -256,11 +368,29 @@ pinctrl-names = "default", "sleep"; pinctrl-0 = <&cpsw_default>; pinctrl-1 = <&cpsw_sleep>; - + status = "okay"; }; &davinci_mdio { pinctrl-names = "default", "sleep"; pinctrl-0 = <&davinci_mdio_default>; pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +&mmc1 { + status = "okay"; + bus-width = <0x4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cd-inverted; +}; + +&aes { + status = "okay"; +}; + +&sham { + status = "okay"; }; diff --git a/arch/arm/dts/am335x-bone.dts b/arch/arm/dts/am335x-bone.dts new file mode 100644 index 0000000..81441cc --- /dev/null +++ b/arch/arm/dts/am335x-bone.dts @@ -0,0 +1,29 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" + +/ { + model = "TI AM335x BeagleBone"; + compatible = "ti,am335x-bone", "ti,am33xx"; + chosen { + stdout-path = &uart0; + }; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&ldo3_reg>; +}; diff --git a/arch/arm/dts/am335x-boneblack.dts b/arch/arm/dts/am335x-boneblack.dts index 197cadf..679248a 100644 --- a/arch/arm/dts/am335x-boneblack.dts +++ b/arch/arm/dts/am335x-boneblack.dts @@ -10,8 +10,80 @@ #include "am33xx.dtsi" #include "am335x-bone-common.dtsi" +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + chosen { + stdout-path = &uart0; + }; +}; + &ldo3_reg { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; }; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&am33xx_pinmux { + nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { + pinctrl-single,pins = < + 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ + 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + >; + }; + nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { + pinctrl-single,pins = < + 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ + >; + }; +}; + +&lcdc { + status = "okay"; +}; + +/ { + hdmi { + compatible = "ti,tilcdc,slave"; + i2c = <&i2c0>; + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; + status = "okay"; + }; +}; + +&rtc { + system-power-controller; +}; diff --git a/arch/arm/dts/am335x-evm.dts b/arch/arm/dts/am335x-evm.dts new file mode 100644 index 0000000..e1c5d4f --- /dev/null +++ b/arch/arm/dts/am335x-evm.dts @@ -0,0 +1,765 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + model = "TI AM335x EVM"; + compatible = "ti,am335x-evm", "ti,am33xx"; + + chosen { + stdout-path = &uart0; + }; + + cpus { + cpu@0 { + cpu0-supply = <&vdd1_reg>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + vbat: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vbat"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + + lis3_reg: fixedregulator@1 { + compatible = "regulator-fixed"; + regulator-name = "lis3_reg"; + regulator-boot-on; + }; + + wlan_en_reg: fixedregulator@2 { + compatible = "regulator-fixed"; + regulator-name = "wlan-en-regulator"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + /* WLAN_EN GPIO for this board - Bank1, pin16 */ + gpio = <&gpio1 16 0>; + + /* WLAN card specific delay */ + startup-delay-us = <70000>; + enable-active-high; + }; + + matrix_keypad: matrix_keypad@0 { + compatible = "gpio-matrix-keypad"; + debounce-delay-ms = <5>; + col-scan-delay-us = <2>; + + row-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH /* Bank1, pin25 */ + &gpio1 26 GPIO_ACTIVE_HIGH /* Bank1, pin26 */ + &gpio1 27 GPIO_ACTIVE_HIGH>; /* Bank1, pin27 */ + + col-gpios = <&gpio1 21 GPIO_ACTIVE_HIGH /* Bank1, pin21 */ + &gpio1 22 GPIO_ACTIVE_HIGH>; /* Bank1, pin22 */ + + linux,keymap = <0x0000008b /* MENU */ + 0x0100009e /* BACK */ + 0x02000069 /* LEFT */ + 0x0001006a /* RIGHT */ + 0x0101001c /* ENTER */ + 0x0201006c>; /* DOWN */ + }; + + gpio_keys: volume_keys@0 { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + + switch@9 { + label = "volume-up"; + linux,code = <115>; + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + gpio-key,wakeup; + }; + + switch@10 { + label = "volume-down"; + linux,code = <114>; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + gpio-key,wakeup; + }; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&ecap0 0 50000 0>; + brightness-levels = <0 51 53 56 62 75 101 152 255>; + default-brightness-level = <8>; + }; + + panel { + compatible = "ti,tilcdc,panel"; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pins_s0>; + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <32>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + + display-timings { + 800x480p62 { + clock-frequency = <30000000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <39>; + hback-porch = <39>; + hsync-len = <47>; + vback-porch = <29>; + vfront-porch = <13>; + vsync-len = <2>; + hsync-active = <1>; + vsync-active = <1>; + }; + }; + }; + + sound { + compatible = "ti,da830-evm-audio"; + ti,model = "AM335x-EVM"; + ti,audio-codec = <&tlv320aic3106>; + ti,mcasp-controller = <&mcasp1>; + ti,codec-clock-rate = <12000000>; + ti,audio-routing = + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT", + "LINE1L", "Line In", + "LINE1R", "Line In"; + }; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>; + + matrix_keypad_s0: matrix_keypad_s0 { + pinctrl-single,pins = < + 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ + 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a6.gpio1_22 */ + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a9.gpio1_25 */ + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a10.gpio1_26 */ + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.gpio1_27 */ + >; + }; + + volume_keys_s0: volume_keys_s0 { + pinctrl-single,pins = < + 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_sclk.gpio0_2 */ + 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d0.gpio0_3 */ + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */ + 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + 0x178 (PIN_INPUT | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */ + 0x17C (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */ + 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */ + 0x184 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */ + >; + }; + + clkout2_pin: pinmux_clkout2_pin { + pinctrl-single,pins = < + 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ + >; + }; + + nandflash_pins_s0: nandflash_pins_s0 { + pinctrl-single,pins = < + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + >; + }; + + ecap0_pins: backlight_pins { + pinctrl-single,pins = < + 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ + 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ + 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ + 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + 0x44 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a1.mmc2_dat0, INPUT_PULLUP | MODE3 */ + 0x48 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a2.mmc2_dat1, INPUT_PULLUP | MODE3 */ + 0x4C (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a3.mmc2_dat2, INPUT_PULLUP | MODE3 */ + 0x78 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ben1.mmc2_dat3, INPUT_PULLUP | MODE3 */ + 0x88 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd, INPUT_PULLUP | MODE3 */ + 0x8C (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc2_clk, INPUT_PULLUP | MODE3 */ + >; + }; + + wlan_pins: pinmux_wlan_pins { + pinctrl-single,pins = < + 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a0.gpio1_16 */ + 0x19C (PIN_INPUT | MUX_MODE7) /* mcasp0_ahclkr.gpio3_17 */ + 0x1AC (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* mcasp0_ahclkx.gpio3_21 */ + >; + }; + + lcd_pins_s0: lcd_pins_s0 { + pinctrl-single,pins = < + 0x20 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad8.lcd_data23 */ + 0x24 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad9.lcd_data22 */ + 0x28 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad10.lcd_data21 */ + 0x2c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad11.lcd_data20 */ + 0x30 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad12.lcd_data19 */ + 0x34 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad13.lcd_data18 */ + 0x38 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad14.lcd_data17 */ + 0x3c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad15.lcd_data16 */ + 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + 0xe0 (PIN_OUTPUT | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + 0xe4 (PIN_OUTPUT | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + 0xe8 (PIN_OUTPUT | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + 0xec (PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + >; + }; + + am335x_evm_audio_pins: am335x_evm_audio_pins { + pinctrl-single,pins = < + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */ + 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ + >; + }; + + dcan1_pins_default: dcan1_pins_default { + pinctrl-single,pins = < + 0x168 (PIN_OUTPUT | MUX_MODE2) /* uart0_ctsn.d_can1_tx */ + 0x16c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* uart0_rtsn.d_can1_rx */ + >; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + + tps: tps@2d { + reg = <0x2d>; + }; +}; + +&usb { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; + dr_mode = "host"; +}; + +&cppi41dma { + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + status = "okay"; + clock-frequency = <100000>; + + lis331dlh: lis331dlh@18 { + compatible = "st,lis331dlh", "st,lis3lv02d"; + reg = <0x18>; + Vdd-supply = <&lis3_reg>; + Vdd_IO-supply = <&lis3_reg>; + + st,click-single-x; + st,click-single-y; + st,click-single-z; + st,click-thresh-x = <10>; + st,click-thresh-y = <10>; + st,click-thresh-z = <10>; + st,irq1-click; + st,irq2-click; + st,wakeup-x-lo; + st,wakeup-x-hi; + st,wakeup-y-lo; + st,wakeup-y-hi; + st,wakeup-z-lo; + st,wakeup-z-hi; + st,min-limit-x = <120>; + st,min-limit-y = <120>; + st,min-limit-z = <140>; + st,max-limit-x = <550>; + st,max-limit-y = <550>; + st,max-limit-z = <750>; + }; + + tsl2550: tsl2550@39 { + compatible = "taos,tsl2550"; + reg = <0x39>; + }; + + tmp275: tmp275@48 { + compatible = "ti,tmp275"; + reg = <0x48>; + }; + + tlv320aic3106: tlv320aic3106@1b { + compatible = "ti,tlv320aic3106"; + reg = <0x1b>; + status = "okay"; + + /* Regulators */ + AVDD-supply = <&vaux2_reg>; + IOVDD-supply = <&vaux2_reg>; + DRVDD-supply = <&vaux2_reg>; + DVDD-supply = <&vbat>; + }; +}; + +&lcdc { + status = "okay"; +}; + +&elm { + status = "okay"; +}; + +&epwmss0 { + status = "okay"; + + ecap0: ecap@48300100 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&ecap0_pins>; + }; +}; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nandflash_pins_s0>; + ranges = <0 0 0x08000000 0x1000000>; /* CS0: 16MB for NAND */ + nand@0,0 { + reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ + ti,nand-ecc-opt = "bch8"; + ti,elm-id = <&elm>; + nand-bus-width = <8>; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <40>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + /* MTD partition table */ + /* All SPL-* partitions are sized to minimal length + * which can be independently programmable. For + * NAND flash this is equal to size of erase-block */ + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "NAND.SPL"; + reg = <0x00000000 0x000020000>; + }; + partition@1 { + label = "NAND.SPL.backup1"; + reg = <0x00020000 0x00020000>; + }; + partition@2 { + label = "NAND.SPL.backup2"; + reg = <0x00040000 0x00020000>; + }; + partition@3 { + label = "NAND.SPL.backup3"; + reg = <0x00060000 0x00020000>; + }; + partition@4 { + label = "NAND.u-boot-spl-os"; + reg = <0x00080000 0x00040000>; + }; + partition@5 { + label = "NAND.u-boot"; + reg = <0x000C0000 0x00100000>; + }; + partition@6 { + label = "NAND.u-boot-env"; + reg = <0x001C0000 0x00020000>; + }; + partition@7 { + label = "NAND.u-boot-env.backup1"; + reg = <0x001E0000 0x00020000>; + }; + partition@8 { + label = "NAND.kernel"; + reg = <0x00200000 0x00800000>; + }; + partition@9 { + label = "NAND.file-system"; + reg = <0x00A00000 0x0F600000>; + }; + }; +}; + +#include "tps65910.dtsi" + +&mcasp1 { + pinctrl-names = "default"; + pinctrl-0 = <&am335x_evm_audio_pins>; + + status = "okay"; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + /* 4 serializers */ + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 1 2 + >; + tx-num-evt = <32>; + rx-num-evt = <32>; +}; + +&tps { + vcc1-supply = <&vbat>; + vcc2-supply = <&vbat>; + vcc3-supply = <&vbat>; + vcc4-supply = <&vbat>; + vcc5-supply = <&vbat>; + vcc6-supply = <&vbat>; + vcc7-supply = <&vbat>; + vccio-supply = <&vbat>; + + regulators { + vrtc_reg: regulator@0 { + regulator-always-on; + }; + + vio_reg: regulator@1 { + regulator-always-on; + }; + + vdd1_reg: regulator@2 { + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <912500>; + regulator-max-microvolt = <1312500>; + regulator-boot-on; + regulator-always-on; + }; + + vdd2_reg: regulator@3 { + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <912500>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + vdd3_reg: regulator@4 { + regulator-always-on; + }; + + vdig1_reg: regulator@5 { + regulator-always-on; + }; + + vdig2_reg: regulator@6 { + regulator-always-on; + }; + + vpll_reg: regulator@7 { + regulator-always-on; + }; + + vdac_reg: regulator@8 { + regulator-always-on; + }; + + vaux1_reg: regulator@9 { + regulator-always-on; + }; + + vaux2_reg: regulator@10 { + regulator-always-on; + }; + + vaux33_reg: regulator@11 { + regulator-always-on; + }; + + vmmc_reg: regulator@12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii-txid"; +}; + +&tscadc { + status = "okay"; + tsc { + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,coordinate-readouts = <5>; + ti,wire-config = <0x00 0x11 0x22 0x33>; + ti,charge-delay = <0x400>; + }; + + adc { + ti,adc-channels = <4 5 6 7>; + }; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&vmmc_reg>; + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; +}; + +&mmc3 { + /* these are on the crossbar and are outlined in the + xbar-event-map element */ + dmas = <&edma 12 + &edma 13>; + dma-names = "tx", "rx"; + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins &wlan_pins>; + ti,non-removable; + ti,needs-special-hs-handling; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@0 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio3>; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&edma { + ti,edma-xbar-event-map = /bits/ 16 <1 12 + 2 13>; +}; + +&sham { + status = "okay"; +}; + +&aes { + status = "okay"; +}; + +&dcan1 { + status = "disabled"; /* Enable only if Profile 1 is selected */ + pinctrl-names = "default"; + pinctrl-0 = <&dcan1_pins_default>; +}; diff --git a/arch/arm/dts/am33xx-clocks.dtsi b/arch/arm/dts/am33xx-clocks.dtsi new file mode 100644 index 0000000..afb4b3a --- /dev/null +++ b/arch/arm/dts/am33xx-clocks.dtsi @@ -0,0 +1,646 @@ +/* + * Device Tree Source for AM33xx clock data + * + * Copyright (C) 2013 Texas Instruments, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +&scm_clocks { + sys_clkin_ck: sys_clkin_ck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&virt_19200000_ck>, <&virt_24000000_ck>, <&virt_25000000_ck>, <&virt_26000000_ck>; + ti,bit-shift = <22>; + reg = <0x0040>; + }; + + adc_tsc_fck: adc_tsc_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&sys_clkin_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + dcan0_fck: dcan0_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&sys_clkin_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + dcan1_fck: dcan1_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&sys_clkin_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + mcasp0_fck: mcasp0_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&sys_clkin_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + mcasp1_fck: mcasp1_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&sys_clkin_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + smartreflex0_fck: smartreflex0_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&sys_clkin_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + smartreflex1_fck: smartreflex1_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&sys_clkin_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + sha0_fck: sha0_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&sys_clkin_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + aes0_fck: aes0_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&sys_clkin_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + rng_fck: rng_fck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&sys_clkin_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + ehrpwm0_tbclk: ehrpwm0_tbclk@44e10664 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&l4ls_gclk>; + ti,bit-shift = <0>; + reg = <0x0664>; + }; + + ehrpwm1_tbclk: ehrpwm1_tbclk@44e10664 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&l4ls_gclk>; + ti,bit-shift = <1>; + reg = <0x0664>; + }; + + ehrpwm2_tbclk: ehrpwm2_tbclk@44e10664 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&l4ls_gclk>; + ti,bit-shift = <2>; + reg = <0x0664>; + }; +}; +&prcm_clocks { + clk_32768_ck: clk_32768_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + }; + + clk_rc32k_ck: clk_rc32k_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32000>; + }; + + virt_19200000_ck: virt_19200000_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <19200000>; + }; + + virt_24000000_ck: virt_24000000_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + }; + + virt_25000000_ck: virt_25000000_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + }; + + virt_26000000_ck: virt_26000000_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <26000000>; + }; + + tclkin_ck: tclkin_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <12000000>; + }; + + dpll_core_ck: dpll_core_ck { + #clock-cells = <0>; + compatible = "ti,am3-dpll-core-clock"; + clocks = <&sys_clkin_ck>, <&sys_clkin_ck>; + reg = <0x0490>, <0x045c>, <0x0468>; + }; + + dpll_core_x2_ck: dpll_core_x2_ck { + #clock-cells = <0>; + compatible = "ti,am3-dpll-x2-clock"; + clocks = <&dpll_core_ck>; + }; + + dpll_core_m4_ck: dpll_core_m4_ck { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll_core_x2_ck>; + ti,max-div = <31>; + reg = <0x0480>; + ti,index-starts-at-one; + }; + + dpll_core_m5_ck: dpll_core_m5_ck { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll_core_x2_ck>; + ti,max-div = <31>; + reg = <0x0484>; + ti,index-starts-at-one; + }; + + dpll_core_m6_ck: dpll_core_m6_ck { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll_core_x2_ck>; + ti,max-div = <31>; + reg = <0x04d8>; + ti,index-starts-at-one; + }; + + dpll_mpu_ck: dpll_mpu_ck { + #clock-cells = <0>; + compatible = "ti,am3-dpll-clock"; + clocks = <&sys_clkin_ck>, <&sys_clkin_ck>; + reg = <0x0488>, <0x0420>, <0x042c>; + }; + + dpll_mpu_m2_ck: dpll_mpu_m2_ck { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll_mpu_ck>; + ti,max-div = <31>; + reg = <0x04a8>; + ti,index-starts-at-one; + }; + + dpll_ddr_ck: dpll_ddr_ck { + #clock-cells = <0>; + compatible = "ti,am3-dpll-no-gate-clock"; + clocks = <&sys_clkin_ck>, <&sys_clkin_ck>; + reg = <0x0494>, <0x0434>, <0x0440>; + }; + + dpll_ddr_m2_ck: dpll_ddr_m2_ck { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll_ddr_ck>; + ti,max-div = <31>; + reg = <0x04a0>; + ti,index-starts-at-one; + }; + + dpll_ddr_m2_div2_ck: dpll_ddr_m2_div2_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_ddr_m2_ck>; + clock-mult = <1>; + clock-div = <2>; + }; + + dpll_disp_ck: dpll_disp_ck { + #clock-cells = <0>; + compatible = "ti,am3-dpll-no-gate-clock"; + clocks = <&sys_clkin_ck>, <&sys_clkin_ck>; + reg = <0x0498>, <0x0448>, <0x0454>; + }; + + dpll_disp_m2_ck: dpll_disp_m2_ck { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll_disp_ck>; + ti,max-div = <31>; + reg = <0x04a4>; + ti,index-starts-at-one; + ti,set-rate-parent; + }; + + dpll_per_ck: dpll_per_ck { + #clock-cells = <0>; + compatible = "ti,am3-dpll-no-gate-j-type-clock"; + clocks = <&sys_clkin_ck>, <&sys_clkin_ck>; + reg = <0x048c>, <0x0470>, <0x049c>; + }; + + dpll_per_m2_ck: dpll_per_m2_ck { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll_per_ck>; + ti,max-div = <31>; + reg = <0x04ac>; + ti,index-starts-at-one; + }; + + dpll_per_m2_div4_wkupdm_ck: dpll_per_m2_div4_wkupdm_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_per_m2_ck>; + clock-mult = <1>; + clock-div = <4>; + }; + + dpll_per_m2_div4_ck: dpll_per_m2_div4_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_per_m2_ck>; + clock-mult = <1>; + clock-div = <4>; + }; + + cefuse_fck: cefuse_fck { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&sys_clkin_ck>; + ti,bit-shift = <1>; + reg = <0x0a20>; + }; + + clk_24mhz: clk_24mhz { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_per_m2_ck>; + clock-mult = <1>; + clock-div = <8>; + }; + + clkdiv32k_ck: clkdiv32k_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&clk_24mhz>; + clock-mult = <1>; + clock-div = <732>; + }; + + clkdiv32k_ick: clkdiv32k_ick { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&clkdiv32k_ck>; + ti,bit-shift = <1>; + reg = <0x014c>; + }; + + l3_gclk: l3_gclk { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_core_m4_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + pruss_ocp_gclk: pruss_ocp_gclk { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&l3_gclk>, <&dpll_disp_m2_ck>; + reg = <0x0530>; + }; + + mmu_fck: mmu_fck { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&dpll_core_m4_ck>; + ti,bit-shift = <1>; + reg = <0x0914>; + }; + + timer1_fck: timer1_fck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&sys_clkin_ck>, <&clkdiv32k_ick>, <&tclkin_ck>, <&clk_rc32k_ck>, <&clk_32768_ck>; + reg = <0x0528>; + }; + + timer2_fck: timer2_fck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>; + reg = <0x0508>; + }; + + timer3_fck: timer3_fck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>; + reg = <0x050c>; + }; + + timer4_fck: timer4_fck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>; + reg = <0x0510>; + }; + + timer5_fck: timer5_fck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>; + reg = <0x0518>; + }; + + timer6_fck: timer6_fck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>; + reg = <0x051c>; + }; + + timer7_fck: timer7_fck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>; + reg = <0x0504>; + }; + + usbotg_fck: usbotg_fck { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&dpll_per_ck>; + ti,bit-shift = <8>; + reg = <0x047c>; + }; + + dpll_core_m4_div2_ck: dpll_core_m4_div2_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_core_m4_ck>; + clock-mult = <1>; + clock-div = <2>; + }; + + ieee5000_fck: ieee5000_fck { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&dpll_core_m4_div2_ck>; + ti,bit-shift = <1>; + reg = <0x00e4>; + }; + + wdt1_fck: wdt1_fck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&clk_rc32k_ck>, <&clkdiv32k_ick>; + reg = <0x0538>; + }; + + l4_rtc_gclk: l4_rtc_gclk { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_core_m4_ck>; + clock-mult = <1>; + clock-div = <2>; + }; + + l4hs_gclk: l4hs_gclk { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_core_m4_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + l3s_gclk: l3s_gclk { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_core_m4_div2_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + l4fw_gclk: l4fw_gclk { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_core_m4_div2_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + l4ls_gclk: l4ls_gclk { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_core_m4_div2_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + sysclk_div_ck: sysclk_div_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_core_m4_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + cpsw_125mhz_gclk: cpsw_125mhz_gclk { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_core_m5_ck>; + clock-mult = <1>; + clock-div = <2>; + }; + + cpsw_cpts_rft_clk: cpsw_cpts_rft_clk { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&dpll_core_m5_ck>, <&dpll_core_m4_ck>; + reg = <0x0520>; + }; + + gpio0_dbclk_mux_ck: gpio0_dbclk_mux_ck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&clk_rc32k_ck>, <&clk_32768_ck>, <&clkdiv32k_ick>; + reg = <0x053c>; + }; + + gpio0_dbclk: gpio0_dbclk { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&gpio0_dbclk_mux_ck>; + ti,bit-shift = <18>; + reg = <0x0408>; + }; + + gpio1_dbclk: gpio1_dbclk { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&clkdiv32k_ick>; + ti,bit-shift = <18>; + reg = <0x00ac>; + }; + + gpio2_dbclk: gpio2_dbclk { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&clkdiv32k_ick>; + ti,bit-shift = <18>; + reg = <0x00b0>; + }; + + gpio3_dbclk: gpio3_dbclk { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&clkdiv32k_ick>; + ti,bit-shift = <18>; + reg = <0x00b4>; + }; + + lcd_gclk: lcd_gclk { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&dpll_disp_m2_ck>, <&dpll_core_m5_ck>, <&dpll_per_m2_ck>; + reg = <0x0534>; + ti,set-rate-parent; + }; + + mmc_clk: mmc_clk { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&dpll_per_m2_ck>; + clock-mult = <1>; + clock-div = <2>; + }; + + gfx_fclk_clksel_ck: gfx_fclk_clksel_ck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&dpll_core_m4_ck>, <&dpll_per_m2_ck>; + ti,bit-shift = <1>; + reg = <0x052c>; + }; + + gfx_fck_div_ck: gfx_fck_div_ck { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&gfx_fclk_clksel_ck>; + reg = <0x052c>; + ti,max-div = <2>; + }; + + sysclkout_pre_ck: sysclkout_pre_ck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&clk_32768_ck>, <&l3_gclk>, <&dpll_ddr_m2_ck>, <&dpll_per_m2_ck>, <&lcd_gclk>; + reg = <0x0700>; + }; + + clkout2_div_ck: clkout2_div_ck { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&sysclkout_pre_ck>; + ti,bit-shift = <3>; + ti,max-div = <8>; + reg = <0x0700>; + }; + + dbg_sysclk_ck: dbg_sysclk_ck { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&sys_clkin_ck>; + ti,bit-shift = <19>; + reg = <0x0414>; + }; + + dbg_clka_ck: dbg_clka_ck { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&dpll_core_m4_ck>; + ti,bit-shift = <30>; + reg = <0x0414>; + }; + + stm_pmd_clock_mux_ck: stm_pmd_clock_mux_ck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&dbg_sysclk_ck>, <&dbg_clka_ck>; + ti,bit-shift = <22>; + reg = <0x0414>; + }; + + trace_pmd_clk_mux_ck: trace_pmd_clk_mux_ck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&dbg_sysclk_ck>, <&dbg_clka_ck>; + ti,bit-shift = <20>; + reg = <0x0414>; + }; + + stm_clk_div_ck: stm_clk_div_ck { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&stm_pmd_clock_mux_ck>; + ti,bit-shift = <27>; + ti,max-div = <64>; + reg = <0x0414>; + ti,index-power-of-two; + }; + + trace_clk_div_ck: trace_clk_div_ck { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&trace_pmd_clk_mux_ck>; + ti,bit-shift = <24>; + ti,max-div = <64>; + reg = <0x0414>; + ti,index-power-of-two; + }; + + clkout2_ck: clkout2_ck { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&clkout2_div_ck>; + ti,bit-shift = <7>; + reg = <0x0700>; + }; +}; + +&prcm_clockdomains { + clk_24mhz_clkdm: clk_24mhz_clkdm { + compatible = "ti,clockdomain"; + clocks = <&clkdiv32k_ick>; + }; +}; diff --git a/arch/arm/dts/am33xx.dtsi b/arch/arm/dts/am33xx.dtsi index f9c5da9..21fcc44 100644 --- a/arch/arm/dts/am33xx.dtsi +++ b/arch/arm/dts/am33xx.dtsi @@ -18,6 +18,9 @@ interrupt-parent = <&intc>; aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; serial0 = &uart0; serial1 = &uart1; serial2 = &uart2; @@ -30,6 +33,8 @@ usb1 = &usb1; phy0 = &usb0_phy; phy1 = &usb1_phy; + ethernet0 = &cpsw_emac0; + ethernet1 = &cpsw_emac1; }; cpus { @@ -53,12 +58,21 @@ 275000 1125000 >; voltage-tolerance = <2>; /* 2 percentage */ + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + clock-latency = <300000>; /* From omap-cpufreq driver */ }; }; + pmu { + compatible = "arm,cortex-a8-pmu"; + interrupts = <3>; + }; + /* - * The soc node represents the soc top level view. It is uses for IPs + * The soc node represents the soc top level view. It is used for IPs * that are not memory mapped in the MPU view or for the MPU itself. */ soc { @@ -69,19 +83,10 @@ }; }; - am33xx_pinmux: pinmux@44e10800 { - compatible = "pinctrl-single"; - reg = <0x44e10800 0x0238>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-single,register-width = <32>; - pinctrl-single,function-mask = <0x7f>; - }; - /* * XXX: Use a flat representation of the AM33XX interconnect. - * The real AM33XX interconnect network is quite complex.Since - * that will not bring real advantage to represent that in DT + * The real AM33XX interconnect network is quite complex. Since + * it will not bring real advantage to represent that in DT * for the moment, just use a fake OCP bus entry to represent * the whole bus hierarchy. */ @@ -92,21 +97,81 @@ ranges; ti,hwmods = "l3_main"; + l4_wkup: l4_wkup@44c00000 { + compatible = "ti,am3-l4-wkup", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x44c00000 0x280000>; + + prcm: prcm@200000 { + compatible = "ti,am3-prcm"; + reg = <0x200000 0x4000>; + + prcm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + prcm_clockdomains: clockdomains { + }; + }; + + scm: scm@210000 { + compatible = "ti,am3-scm", "simple-bus"; + reg = <0x210000 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x210000 0x2000>; + + am33xx_pinmux: pinmux@800 { + compatible = "pinctrl-single"; + reg = <0x800 0x238>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x7f>; + }; + + scm_conf: scm_conf@0 { + compatible = "syscon"; + reg = <0x0 0x800>; + #address-cells = <1>; + #size-cells = <1>; + + scm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + scm_clockdomains: clockdomains { + }; + }; + }; + intc: interrupt-controller@48200000 { - compatible = "ti,omap2-intc"; + compatible = "ti,am33xx-intc"; interrupt-controller; #interrupt-cells = <1>; - ti,intc-size = <128>; reg = <0x48200000 0x1000>; }; + edma: edma@49000000 { + compatible = "ti,edma3"; + ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; + reg = <0x49000000 0x10000>, + <0x44e10f90 0x40>; + interrupts = <12 13 14>; + #dma-cells = <1>; + }; + gpio0: gpio@44e07000 { compatible = "ti,omap4-gpio"; ti,hwmods = "gpio1"; gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; reg = <0x44e07000 0x1000>; interrupts = <96>; }; @@ -117,7 +182,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; reg = <0x4804c000 0x1000>; interrupts = <98>; }; @@ -128,7 +193,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; reg = <0x481ac000 0x1000>; interrupts = <32>; }; @@ -139,7 +204,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; reg = <0x481ae000 0x1000>; interrupts = <62>; }; @@ -151,6 +216,8 @@ reg = <0x44e09000 0x2000>; interrupts = <72>; status = "disabled"; + dmas = <&edma 26>, <&edma 27>; + dma-names = "tx", "rx"; }; uart1: serial@48022000 { @@ -160,6 +227,8 @@ reg = <0x48022000 0x2000>; interrupts = <73>; status = "disabled"; + dmas = <&edma 28>, <&edma 29>; + dma-names = "tx", "rx"; }; uart2: serial@48024000 { @@ -169,6 +238,8 @@ reg = <0x48024000 0x2000>; interrupts = <74>; status = "disabled"; + dmas = <&edma 30>, <&edma 31>; + dma-names = "tx", "rx"; }; uart3: serial@481a6000 { @@ -228,6 +299,51 @@ status = "disabled"; }; + mmc1: mmc@48060000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc1"; + ti,dual-volt; + ti,needs-special-reset; + ti,needs-special-hs-handling; + dmas = <&edma 24 + &edma 25>; + dma-names = "tx", "rx"; + interrupts = <64>; + interrupt-parent = <&intc>; + reg = <0x48060000 0x1000>; + status = "disabled"; + }; + + mmc2: mmc@481d8000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc2"; + ti,needs-special-reset; + dmas = <&edma 2 + &edma 3>; + dma-names = "tx", "rx"; + interrupts = <28>; + interrupt-parent = <&intc>; + reg = <0x481d8000 0x1000>; + status = "disabled"; + }; + + mmc3: mmc@47810000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc3"; + ti,needs-special-reset; + interrupts = <29>; + interrupt-parent = <&intc>; + reg = <0x47810000 0x1000>; + status = "disabled"; + }; + + hwspinlock: spinlock@480ca000 { + compatible = "ti,omap4-hwspinlock"; + reg = <0x480ca000 0x1000>; + ti,hwmods = "spinlock"; + #hwlock-cells = <1>; + }; + wdt2: wdt@44e35000 { compatible = "ti,omap3-wdt"; ti,hwmods = "wd_timer2"; @@ -235,24 +351,42 @@ interrupts = <91>; }; - dcan0: d_can@481cc000 { - compatible = "bosch,d_can"; + dcan0: can@481cc000 { + compatible = "ti,am3352-d_can"; ti,hwmods = "d_can0"; - reg = <0x481cc000 0x2000 - 0x44e10644 0x4>; + reg = <0x481cc000 0x2000>; + clocks = <&dcan0_fck>; + clock-names = "fck"; + syscon-raminit = <&scm_conf 0x644 0>; interrupts = <52>; status = "disabled"; }; - dcan1: d_can@481d0000 { - compatible = "bosch,d_can"; + dcan1: can@481d0000 { + compatible = "ti,am3352-d_can"; ti,hwmods = "d_can1"; - reg = <0x481d0000 0x2000 - 0x44e10644 0x4>; + reg = <0x481d0000 0x2000>; + clocks = <&dcan1_fck>; + clock-names = "fck"; + syscon-raminit = <&scm_conf 0x644 1>; interrupts = <55>; status = "disabled"; }; + mailbox: mailbox@480C8000 { + compatible = "ti,omap4-mailbox"; + reg = <0x480C8000 0x200>; + interrupts = <77>; + ti,hwmods = "mailbox"; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <8>; + mbox_wkupm3: wkup_m3 { + ti,mbox-tx = <0 0 0>; + ti,mbox-rx = <0 0 3>; + }; + }; + timer1: timer@44e31000 { compatible = "ti,am335x-timer-1ms"; reg = <0x44e31000 0x400>; @@ -307,8 +441,8 @@ ti,timer-pwm; }; - rtc@44e3e000 { - compatible = "ti,da830-rtc"; + rtc: rtc@44e3e000 { + compatible = "ti,am3352-rtc", "ti,da830-rtc"; reg = <0x44e3e000 0x1000>; interrupts = <75 76>; @@ -323,6 +457,11 @@ interrupts = <65>; ti,spi-num-cs = <2>; ti,hwmods = "spi0"; + dmas = <&edma 16 + &edma 17 + &edma 18 + &edma 19>; + dma-names = "tx0", "rx0", "tx1", "rx1"; status = "disabled"; }; @@ -334,6 +473,11 @@ interrupts = <125>; ti,spi-num-cs = <2>; ti,hwmods = "spi1"; + dmas = <&edma 42 + &edma 43 + &edma 44 + &edma 45>; + dma-names = "tx0", "rx0", "tx1", "rx1"; status = "disabled"; }; @@ -346,7 +490,7 @@ ti,hwmods = "usb_otg_hs"; status = "disabled"; - ctrl_mod: control@44e10000 { + usb_ctrl_mod: control@44e10620 { compatible = "ti,am335x-usb-ctrl-module"; reg = <0x44e10620 0x10 0x44e10648 0x4>; @@ -359,7 +503,7 @@ reg = <0x47401300 0x100>; reg-names = "phy"; status = "disabled"; - ti,ctrl_mod = <&ctrl_mod>; + ti,ctrl_mod = <&usb_ctrl_mod>; }; usb0: usb@47401000 { @@ -407,7 +551,7 @@ reg = <0x47401b00 0x100>; reg-names = "phy"; status = "disabled"; - ti,ctrl_mod = <&ctrl_mod>; + ti,ctrl_mod = <&usb_ctrl_mod>; }; usb1: usb@47401800 { @@ -449,7 +593,7 @@ "tx14", "tx15"; }; - cppi41dma: dma-controller@07402000 { + cppi41dma: dma-controller@47402000 { compatible = "ti,am3359-cppi41"; reg = <0x47400000 0x1000 0x47402000 0x1000 @@ -480,6 +624,8 @@ compatible = "ti,am33xx-ecap"; #pwm-cells = <3>; reg = <0x48300100 0x80>; + interrupts = <31>; + interrupt-names = "ecap0"; ti,hwmods = "ecap0"; status = "disabled"; }; @@ -508,6 +654,8 @@ compatible = "ti,am33xx-ecap"; #pwm-cells = <3>; reg = <0x48302100 0x80>; + interrupts = <47>; + interrupt-names = "ecap1"; ti,hwmods = "ecap1"; status = "disabled"; }; @@ -536,6 +684,8 @@ compatible = "ti,am33xx-ecap"; #pwm-cells = <3>; reg = <0x48304100 0x80>; + interrupts = <61>; + interrupt-names = "ecap2"; ti,hwmods = "ecap2"; status = "disabled"; }; @@ -552,6 +702,8 @@ mac: ethernet@4a100000 { compatible = "ti,cpsw"; ti,hwmods = "cpgmac0"; + clocks = <&cpsw_125mhz_gclk>, <&cpsw_cpts_rft_clk>; + clock-names = "fck", "cpts"; cpdma_channels = <8>; ale_entries = <1024>; bd_ram_size = <0x2000>; @@ -575,6 +727,8 @@ */ interrupts = <40 41 42 43>; ranges; + syscon = <&scm_conf>; + status = "disabled"; davinci_mdio: mdio@4a101000 { compatible = "ti,davinci_mdio"; @@ -583,6 +737,7 @@ ti,hwmods = "davinci_mdio"; bus_freq = <1000000>; reg = <0x4a101000 0x100>; + status = "disabled"; }; cpsw_emac0: slave@4a100200 { @@ -594,12 +749,17 @@ /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; + + phy_sel: cpsw-phy-sel@44e10650 { + compatible = "ti,am3352-cpsw-phy-sel"; + reg= <0x44e10650 0x4>; + reg-names = "gmii-sel"; + }; }; ocmcram: ocmcram@40300000 { - compatible = "ti,am3352-ocmcram"; - reg = <0x40300000 0x10000>; - ti,hwmods = "ocmcram"; + compatible = "mmio-sram"; + reg = <0x40300000 0x10000>; /* 64k */ }; wkup_m3: wkup_m3@44d00000 { @@ -607,6 +767,7 @@ reg = <0x44d00000 0x4000 /* M3 UMEM */ 0x44d80000 0x2000>; /* M3 DMEM */ ti,hwmods = "wkup_m3"; + ti,no-reset-on-init; }; elm: elm@48080000 { @@ -617,6 +778,15 @@ status = "disabled"; }; + lcdc: lcdc@4830e000 { + compatible = "ti,am33xx-tilcdc"; + reg = <0x4830e000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <36>; + ti,hwmods = "lcdc"; + status = "disabled"; + }; + tscadc: tscadc@44e0d000 { compatible = "ti,am3359-tscadc"; reg = <0x44e0d000 0x1000>; @@ -637,6 +807,7 @@ gpmc: gpmc@50000000 { compatible = "ti,am3352-gpmc"; ti,hwmods = "gpmc"; + ti,no-idle-on-init; reg = <0x50000000 0x2000>; interrupts = <100>; gpmc,num-cs = <7>; @@ -645,5 +816,61 @@ #size-cells = <1>; status = "disabled"; }; + + sham: sham@53100000 { + compatible = "ti,omap4-sham"; + ti,hwmods = "sham"; + reg = <0x53100000 0x200>; + interrupts = <109>; + dmas = <&edma 36>; + dma-names = "rx"; + }; + + aes: aes@53500000 { + compatible = "ti,omap4-aes"; + ti,hwmods = "aes"; + reg = <0x53500000 0xa0>; + interrupts = <103>; + dmas = <&edma 6>, + <&edma 5>; + dma-names = "tx", "rx"; + }; + + mcasp0: mcasp@48038000 { + compatible = "ti,am33xx-mcasp-audio"; + ti,hwmods = "mcasp0"; + reg = <0x48038000 0x2000>, + <0x46000000 0x400000>; + reg-names = "mpu", "dat"; + interrupts = <80>, <81>; + interrupt-names = "tx", "rx"; + status = "disabled"; + dmas = <&edma 8>, + <&edma 9>; + dma-names = "tx", "rx"; + }; + + mcasp1: mcasp@4803C000 { + compatible = "ti,am33xx-mcasp-audio"; + ti,hwmods = "mcasp1"; + reg = <0x4803C000 0x2000>, + <0x46400000 0x400000>; + reg-names = "mpu", "dat"; + interrupts = <82>, <83>; + interrupt-names = "tx", "rx"; + status = "disabled"; + dmas = <&edma 10>, + <&edma 11>; + dma-names = "tx", "rx"; + }; + + rng: rng@48310000 { + compatible = "ti,omap4-rng"; + ti,hwmods = "rng"; + reg = <0x48310000 0x2000>; + interrupts = <111>; + }; }; }; + +/include/ "am33xx-clocks.dtsi" diff --git a/arch/arm/dts/tps65910.dtsi b/arch/arm/dts/tps65910.dtsi new file mode 100644 index 0000000..b0ac665 --- /dev/null +++ b/arch/arm/dts/tps65910.dtsi @@ -0,0 +1,91 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Integrated Power Management Chip + * http://www.ti.com/lit/ds/symlink/tps65910.pdf + */ + +&tps { + compatible = "ti,tps65910"; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + vrtc_reg: regulator@0 { + reg = <0>; + regulator-compatible = "vrtc"; + }; + + vio_reg: regulator@1 { + reg = <1>; + regulator-compatible = "vio"; + }; + + vdd1_reg: regulator@2 { + reg = <2>; + regulator-compatible = "vdd1"; + }; + + vdd2_reg: regulator@3 { + reg = <3>; + regulator-compatible = "vdd2"; + }; + + vdd3_reg: regulator@4 { + reg = <4>; + regulator-compatible = "vdd3"; + }; + + vdig1_reg: regulator@5 { + reg = <5>; + regulator-compatible = "vdig1"; + }; + + vdig2_reg: regulator@6 { + reg = <6>; + regulator-compatible = "vdig2"; + }; + + vpll_reg: regulator@7 { + reg = <7>; + regulator-compatible = "vpll"; + }; + + vdac_reg: regulator@8 { + reg = <8>; + regulator-compatible = "vdac"; + }; + + vaux1_reg: regulator@9 { + reg = <9>; + regulator-compatible = "vaux1"; + }; + + vaux2_reg: regulator@10 { + reg = <10>; + regulator-compatible = "vaux2"; + }; + + vaux33_reg: regulator@11 { + reg = <11>; + regulator-compatible = "vaux33"; + }; + + vmmc_reg: regulator@12 { + reg = <12>; + regulator-compatible = "vmmc"; + }; + + vbb_reg: regulator@13 { + reg = <13>; + regulator-compatible = "vbb"; + }; + }; +}; diff --git a/configs/am335x_gp_evm_defconfig b/configs/am335x_gp_evm_defconfig new file mode 100644 index 0000000..62d3b6b --- /dev/null +++ b/configs/am335x_gp_evm_defconfig @@ -0,0 +1,14 @@ +CONFIG_ARM=y +CONFIG_TARGET_AM335X_EVM=y +CONFIG_DEFAULT_DEVICE_TREE="am335x-evm" +CONFIG_SPL=y +CONFIG_SPL_STACK_R=y +CONFIG_SPL_STACK_R_ADDR=0x82000000 +CONFIG_SYS_EXTRA_OPTIONS="NAND" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_SETEXPR is not set +CONFIG_OF_CONTROL=y +CONFIG_SPL_DISABLE_OF_CONTROL=y +CONFIG_SPI_FLASH=y +CONFIG_RSA=y -- 1.7.9.5

2 14