November 2015 - U-Boot

[U-Boot] [PATCH v2] mpc85xx: Add support for the Varisys Cyrus board
by Andy Fleming 04 Nov '15

04 Nov '15

This board runs a P5020 or P5040 chip, and utilizes an EEPROM with similar formatting to the Freescale P5020DS. Large amounts of this code were developed by Adrian Cox <adrian at humboldt dot co dot uk> Signed-off-by: Andy Fleming <afleming(a)gmail.com> --- v2: * Cleaned up sys_eeprom.c * Removed CONFIG_CMD_ELF, CONFIG_SYS_GENERIC_BOARD arch/powerpc/cpu/mpc85xx/Kconfig | 4 + board/varisys/common/Makefile | 23 ++ board/varisys/common/eeprom.h | 6 + board/varisys/common/sys_eeprom.c | 500 +++++++++++++++++++++++++++++ board/varisys/cyrus/Kconfig | 13 + board/varisys/cyrus/Makefile | 8 + board/varisys/cyrus/README | 21 ++ board/varisys/cyrus/cyrus.c | 116 +++++++ board/varisys/cyrus/cyrus.h | 11 + board/varisys/cyrus/ddr.c | 188 +++++++++++ board/varisys/cyrus/eth.c | 100 ++++++ board/varisys/cyrus/law.c | 27 ++ board/varisys/cyrus/pbi.cfg | 35 +++ board/varisys/cyrus/pci.c | 23 ++ board/varisys/cyrus/rcw_p5020_v2.cfg | 11 + board/varisys/cyrus/rcw_p5040.cfg | 11 + board/varisys/cyrus/tlb.c | 106 +++++++ configs/Cyrus_P5020_defconfig | 9 + configs/Cyrus_P5040_defconfig | 9 + include/configs/cyrus.h | 588 +++++++++++++++++++++++++++++++++++ 20 files changed, 1809 insertions(+) create mode 100644 board/varisys/common/Makefile create mode 100644 board/varisys/common/eeprom.h create mode 100644 board/varisys/common/sys_eeprom.c create mode 100644 board/varisys/cyrus/Kconfig create mode 100644 board/varisys/cyrus/Makefile create mode 100644 board/varisys/cyrus/README create mode 100644 board/varisys/cyrus/cyrus.c create mode 100644 board/varisys/cyrus/cyrus.h create mode 100644 board/varisys/cyrus/ddr.c create mode 100644 board/varisys/cyrus/eth.c create mode 100644 board/varisys/cyrus/law.c create mode 100644 board/varisys/cyrus/pbi.cfg create mode 100644 board/varisys/cyrus/pci.c create mode 100644 board/varisys/cyrus/rcw_p5020_v2.cfg create mode 100644 board/varisys/cyrus/rcw_p5040.cfg create mode 100644 board/varisys/cyrus/tlb.c create mode 100644 configs/Cyrus_P5020_defconfig create mode 100644 configs/Cyrus_P5040_defconfig create mode 100644 include/configs/cyrus.h diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig index ae0823a..0b89157 100644 --- a/arch/powerpc/cpu/mpc85xx/Kconfig +++ b/arch/powerpc/cpu/mpc85xx/Kconfig @@ -149,6 +149,9 @@ config TARGET_XPEDITE550X config TARGET_UCP1020 bool "Support uCP1020" +config TARGET_CYRUS + bool "Support Varisys Cyrus" + endchoice source "board/freescale/b4860qds/Kconfig" @@ -185,6 +188,7 @@ source "board/gdsys/p1022/Kconfig" source "board/keymile/kmp204x/Kconfig" source "board/sbc8548/Kconfig" source "board/socrates/Kconfig" +source "board/varisys/cyrus/Kconfig" source "board/xes/xpedite520x/Kconfig" source "board/xes/xpedite537x/Kconfig" source "board/xes/xpedite550x/Kconfig" diff --git a/board/varisys/common/Makefile b/board/varisys/common/Makefile new file mode 100644 index 0000000..1e6dcbb --- /dev/null +++ b/board/varisys/common/Makefile @@ -0,0 +1,23 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +MINIMAL= + +ifdef CONFIG_SPL_BUILD +ifdef CONFIG_SPL_INIT_MINIMAL +MINIMAL=y +endif +endif + +ifdef MINIMAL +# necessary to create built-in.o +obj- := __dummy__.o +else +ifndef CONFIG_SPL_BUILD +obj-$(CONFIG_ID_EEPROM) += sys_eeprom.o +endif +endif diff --git a/board/varisys/common/eeprom.h b/board/varisys/common/eeprom.h new file mode 100644 index 0000000..004816a --- /dev/null +++ b/board/varisys/common/eeprom.h @@ -0,0 +1,6 @@ +/* EEPROM init functions for Cyrus */ + + +void init_eeprom(int bus_num, int addr, int addr_len); +void mac_read_from_fixed_id(void); +int mac_read_from_eeprom_common(void); diff --git a/board/varisys/common/sys_eeprom.c b/board/varisys/common/sys_eeprom.c new file mode 100644 index 0000000..086fad2 --- /dev/null +++ b/board/varisys/common/sys_eeprom.c @@ -0,0 +1,500 @@ +/* + * Copyright 2006, 2008-2009, 2011 Freescale Semiconductor + * York Sun (yorksun(a)freescale.com) + * Haiying Wang (haiying.wang(a)freescale.com) + * Timur Tabi (timur(a)freescale.com) + * + * This defines the API for storing board information in the + * eeprom. It has been adapted from an earlier version of the + * Freescale code for doing the same thing. Therefore it is + * nearly identical to the Freescale code, but is intended for + * use with Varisys-produced boards. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <i2c.h> +#include <linux/ctype.h> + +#include "eeprom.h" + +#ifdef CONFIG_SYS_I2C_EEPROM_NXID_MAC +#define MAX_NUM_PORTS CONFIG_SYS_I2C_EEPROM_NXID_MAC +#else +#define MAX_NUM_PORTS 8 +#endif +#define NXID_VERSION 0 + +/** + * static eeprom: EEPROM layout for NXID formats + * + * See Freescale application note AN3638 for details. + */ +static struct __attribute__ ((__packed__)) eeprom { + u8 id[4]; /* 0x00 - 0x03 EEPROM Tag 'NXID' */ + u8 sn[12]; /* 0x04 - 0x0F Serial Number */ + u8 errata[5]; /* 0x10 - 0x14 Errata Level */ + u8 date[6]; /* 0x15 - 0x1a Build Date */ + u8 res_0; /* 0x1b Reserved */ + u32 version; /* 0x1c - 0x1f NXID Version */ + u8 tempcal[8]; /* 0x20 - 0x27 Temperature Calibration Factors */ + u8 tempcalsys[2]; /* 0x28 - 0x29 System Temperature Calibration Factors */ + u8 tempcalflags; /* 0x2a Temperature Calibration Flags */ + u8 res_1[21]; /* 0x2b - 0x3f Reserved */ + u8 mac_count; /* 0x40 Number of MAC addresses */ + u8 mac_flag; /* 0x41 MAC table flags */ + u8 mac[MAX_NUM_PORTS][6]; /* 0x42 - x MAC addresses */ + u32 crc; /* x+1 CRC32 checksum */ +} e; + +/* Set to 1 if we've read EEPROM into memory */ +static int has_been_read; + +/* Is this a valid NXID EEPROM? */ +#define is_valid ((e.id[0] == 'N') || (e.id[1] == 'X') || \ + (e.id[2] == 'I') || (e.id[3] == 'D')) + +/** Fixed ID field in EEPROM */ +static unsigned char uid[16]; + +static int eeprom_bus_num = -1; +static int eeprom_addr; +static int eeprom_addr_len; + +/** + * This must be called before any eeprom access. + */ +void init_eeprom(int bus_num, int addr, int addr_len) +{ + eeprom_bus_num = bus_num; + eeprom_addr = addr; + eeprom_addr_len = addr_len; +} + +/** + * show_eeprom - display the contents of the EEPROM + */ +void show_eeprom(void) +{ + int i; + unsigned int crc; + + /* EEPROM tag ID, either CCID or NXID */ + printf("ID: %c%c%c%c v%u\n", e.id[0], e.id[1], e.id[2], e.id[3], + be32_to_cpu(e.version)); + + /* Serial number */ + printf("SN: %s\n", e.sn); + + printf("UID: "); + for (i = 0; i < 16; i++) + printf("%02x", uid[i]); + printf("\n"); + + /* Errata level. */ + printf("Errata: %s\n", e.errata); + + /* Build date, BCD date values, as YYMMDDhhmmss */ + printf("Build date: 20%02x/%02x/%02x %02x:%02x:%02x %s\n", + e.date[0], e.date[1], e.date[2], + e.date[3] & 0x7F, e.date[4], e.date[5], + e.date[3] & 0x80 ? "PM" : ""); + + /* Show MAC addresses */ + for (i = 0; i < min(e.mac_count, (u8)MAX_NUM_PORTS); i++) { + u8 *p = e.mac[i]; + + printf("Eth%u: %02x:%02x:%02x:%02x:%02x:%02x\n", i, + p[0], p[1], p[2], p[3], p[4], p[5]); + } + + crc = crc32(0, (void *)&e, sizeof(e) - 4); + + if (crc == be32_to_cpu(e.crc)) + printf("CRC: %08x\n", be32_to_cpu(e.crc)); + else + printf("CRC: %08x (should be %08x)\n", + be32_to_cpu(e.crc), crc); + +#ifdef DEBUG + printf("EEPROM dump: (0x%x bytes)\n", sizeof(e)); + for (i = 0; i < sizeof(e); i++) { + if ((i % 16) == 0) + printf("%02X: ", i); + printf("%02X ", ((u8 *)&e)[i]); + if (((i % 16) == 15) || (i == sizeof(e) - 1)) + printf("\n"); + } +#endif +} + +/** + * read_eeprom - read the EEPROM into memory + */ +int read_eeprom(void) +{ + int ret; + unsigned int bus; + + if (eeprom_bus_num < 0) { + printf("EEPROM not configured\n"); + return -1; + } + + if (has_been_read) + return 0; + + bus = i2c_get_bus_num(); + i2c_set_bus_num(eeprom_bus_num); + + ret = i2c_read(eeprom_addr, 0, eeprom_addr_len, + (void *)&e, sizeof(e)); + + + /* Fixed address of ID field */ + i2c_read(0x5f, 0x80, 1, uid, 16); + + i2c_set_bus_num(bus); + +#ifdef DEBUG + show_eeprom(); +#endif + + has_been_read = (ret == 0) ? 1 : 0; + + return ret; +} + +/** + * update_crc - update the CRC + * + * This function should be called after each update to the EEPROM structure, + * to make sure the CRC is always correct. + */ +static void update_crc(void) +{ + u32 crc, crc_offset = offsetof(struct eeprom, crc); + + crc = crc32(0, (void *)&e, crc_offset); + e.crc = cpu_to_be32(crc); +} + +/** + * prog_eeprom - write the EEPROM from memory + */ +static int prog_eeprom(void) +{ + int ret = 0; + int i; + void *p; + unsigned int bus; + + if (eeprom_bus_num < 0) { + printf("EEPROM not configured\n"); + return -1; + } + + /* Set the reserved values to 0xFF */ + e.res_0 = 0xFF; + memset(e.res_1, 0xFF, sizeof(e.res_1)); + update_crc(); + + bus = i2c_get_bus_num(); + i2c_set_bus_num(eeprom_bus_num); + + /* + * The AT24C02 datasheet says that data can only be written in page + * mode, which means 8 bytes at a time, and it takes up to 5ms to + * complete a given write. + */ + for (i = 0, p = &e; i < sizeof(e); i += 8, p += 8) { + ret = i2c_write(eeprom_addr, i, eeprom_addr_len, + p, min((int)(sizeof(e) - i), 8)); + if (ret) + break; + udelay(5000); /* 5ms write cycle timing */ + } + + if (!ret) { + /* Verify the write by reading back the EEPROM and comparing */ + struct eeprom e2; + + ret = i2c_read(eeprom_addr, 0, + eeprom_addr_len, (void *)&e2, sizeof(e2)); + if (!ret && memcmp(&e, &e2, sizeof(e))) + ret = -1; + } + + i2c_set_bus_num(bus); + + if (ret) { + printf("Programming failed.\n"); + has_been_read = 0; + return -1; + } + + printf("Programming passed.\n"); + return 0; +} + +/** + * h2i - converts hex character into a number + * + * This function takes a hexadecimal character (e.g. '7' or 'C') and returns + * the integer equivalent. + */ +static inline u8 h2i(char p) +{ + if ((p >= '0') && (p <= '9')) + return p - '0'; + + if ((p >= 'A') && (p <= 'F')) + return (p - 'A') + 10; + + if ((p >= 'a') && (p <= 'f')) + return (p - 'a') + 10; + + return 0; +} + +/** + * set_date - stores the build date into the EEPROM + * + * This function takes a pointer to a string in the format "YYMMDDhhmmss" + * (2-digit year, 2-digit month, etc), converts it to a 6-byte BCD string, + * and stores it in the build date field of the EEPROM local copy. + */ +static void set_date(const char *string) +{ + unsigned int i; + + if (strlen(string) != 12) { + printf("Usage: mac date YYMMDDhhmmss\n"); + return; + } + + for (i = 0; i < 6; i++) + e.date[i] = h2i(string[2 * i]) << 4 | h2i(string[2 * i + 1]); + + update_crc(); +} + +/** + * set_mac_address - stores a MAC address into the EEPROM + * + * This function takes a pointer to MAC address string + * (i.e."XX:XX:XX:XX:XX:XX", where "XX" is a two-digit hex number) and + * stores it in one of the MAC address fields of the EEPROM local copy. + */ +static void set_mac_address(unsigned int index, const char *string) +{ + char *p = (char *)string; + unsigned int i; + + if ((index >= MAX_NUM_PORTS) || !string) { + printf("Usage: mac <n> XX:XX:XX:XX:XX:XX\n"); + return; + } + + for (i = 0; *p && (i < 6); i++) { + e.mac[index][i] = simple_strtoul(p, &p, 16); + if (*p == ':') + p++; + } + + update_crc(); +} + +int do_mac(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + char cmd; + + if (argc == 1) { + show_eeprom(); + return 0; + } + + cmd = argv[1][0]; + + if (cmd == 'r') { + read_eeprom(); + return 0; + } + + if (cmd == 'i') { + memcpy(e.id, "NXID", sizeof(e.id)); + e.version = NXID_VERSION; + update_crc(); + return 0; + } + + if (!is_valid) { + printf("Please read the EEPROM ('r') and/or set the ID ('i') first.\n"); + return 0; + } + + if (argc == 2) { + switch (cmd) { + case 's': /* save */ + prog_eeprom(); + break; + default: + return cmd_usage(cmdtp); + } + + return 0; + } + + /* We know we have at least one parameter */ + + switch (cmd) { + case 'n': /* serial number */ + memset(e.sn, 0, sizeof(e.sn)); + strncpy((char *)e.sn, argv[2], sizeof(e.sn) - 1); + update_crc(); + break; + case 'e': /* errata */ + memset(e.errata, 0, 5); + strncpy((char *)e.errata, argv[2], 4); + update_crc(); + break; + case 'd': /* date BCD format YYMMDDhhmmss */ + set_date(argv[2]); + break; + case 'p': /* MAC table size */ + e.mac_count = simple_strtoul(argv[2], NULL, 16); + update_crc(); + break; + case '0' ... '9': /* "mac 0" through "mac 22" */ + set_mac_address(simple_strtoul(argv[1], NULL, 10), argv[2]); + break; + case 'h': /* help */ + default: + return cmd_usage(cmdtp); + } + + return 0; +} + +int mac_read_from_generic_eeprom(const char *envvar, int chip, + int address, int mac_bus) +{ + int ret; + unsigned int bus; + unsigned char mac[6]; + char ethaddr[18]; + + bus = i2c_get_bus_num(); + i2c_set_bus_num(mac_bus); + + ret = i2c_read(chip, address, 1, mac, 6); + + i2c_set_bus_num(bus); + + if (!ret) { + sprintf(ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X", + mac[0], + mac[1], + mac[2], + mac[3], + mac[4], + mac[5]); + + printf("MAC: %s\n", ethaddr); + setenv(envvar, ethaddr); + } + + return ret; +} + +void mac_read_from_fixed_id(void) +{ +#ifdef CONFIG_SYS_I2C_MAC1_CHIP_ADDR + mac_read_from_generic_eeprom("ethaddr", CONFIG_SYS_I2C_MAC1_CHIP_ADDR, + CONFIG_SYS_I2C_MAC1_DATA_ADDR, CONFIG_SYS_I2C_MAC1_BUS); +#endif +#ifdef CONFIG_SYS_I2C_MAC2_CHIP_ADDR + mac_read_from_generic_eeprom("eth1addr", CONFIG_SYS_I2C_MAC2_CHIP_ADDR, + CONFIG_SYS_I2C_MAC2_DATA_ADDR, CONFIG_SYS_I2C_MAC2_BUS); +#endif +} + +/** + * mac_read_from_eeprom - read the MAC addresses from EEPROM + * + * This function reads the MAC addresses from EEPROM and sets the + * appropriate environment variables for each one read. + * + * The environment variables are only set if they haven't been set already. + * This ensures that any user-saved variables are never overwritten. + * + * This function must be called after relocation. + * + * For NXID v1 EEPROMs, we support loading and up-converting the older NXID v0 + * format. In a v0 EEPROM, there are only eight MAC addresses and the CRC is + * located at a different offset. + */ +int mac_read_from_eeprom_common(void) +{ + unsigned int i; + u32 crc, crc_offset = offsetof(struct eeprom, crc); + u32 *crcp; /* Pointer to the CRC in the data read from the EEPROM */ + + puts("EEPROM: "); + + if (read_eeprom()) { + printf("Read failed.\n"); + return 0; + } + + if (!is_valid) { + printf("Invalid ID (%02x %02x %02x %02x)\n", + e.id[0], e.id[1], e.id[2], e.id[3]); + return 0; + } + + crc = crc32(0, (void *)&e, crc_offset); + crcp = (void *)&e + crc_offset; + if (crc != be32_to_cpu(*crcp)) { + printf("CRC mismatch (%08x != %08x)\n", crc, + be32_to_cpu(e.crc)); + return 0; + } + + /* + * MAC address #9 in v1 occupies the same position as the CRC in v0. + * Erase it so that it's not mistaken for a MAC address. We'll + * update the CRC later. + */ + if (e.version == 0) + memset(e.mac[8], 0xff, 6); + + for (i = 0; i < min(e.mac_count, (u8)MAX_NUM_PORTS); i++) { + if (memcmp(&e.mac[i], "\0\0\0\0\0\0", 6) && + memcmp(&e.mac[i], "\xFF\xFF\xFF\xFF\xFF\xFF", 6)) { + char ethaddr[18]; + char enetvar[9]; + + sprintf(ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X", + e.mac[i][0], + e.mac[i][1], + e.mac[i][2], + e.mac[i][3], + e.mac[i][4], + e.mac[i][5]); + sprintf(enetvar, i ? "eth%daddr" : "ethaddr", i); + /* Only initialize environment variables that are blank + * (i.e. have not yet been set) + */ + if (!getenv(enetvar)) + setenv(enetvar, ethaddr); + } + } + + printf("%c%c%c%c v%u\n", e.id[0], e.id[1], e.id[2], e.id[3], + be32_to_cpu(e.version)); + + return 0; +} diff --git a/board/varisys/cyrus/Kconfig b/board/varisys/cyrus/Kconfig new file mode 100644 index 0000000..bed6f4f --- /dev/null +++ b/board/varisys/cyrus/Kconfig @@ -0,0 +1,13 @@ +if TARGET_CYRUS + +config SYS_BOARD + default "cyrus" + +config SYS_VENDOR + default "varisys" + +config SYS_CONFIG_NAME + default "cyrus" + +endif + diff --git a/board/varisys/cyrus/Makefile b/board/varisys/cyrus/Makefile new file mode 100644 index 0000000..303fc42 --- /dev/null +++ b/board/varisys/cyrus/Makefile @@ -0,0 +1,8 @@ +# + +obj-y += $(BOARD).o +obj-y += ddr.o +obj-y += law.o +obj-y += tlb.o +obj-y += eth.o +obj-$(CONFIG_PCI) += pci.o diff --git a/board/varisys/cyrus/README b/board/varisys/cyrus/README new file mode 100644 index 0000000..3f675ab --- /dev/null +++ b/board/varisys/cyrus/README @@ -0,0 +1,21 @@ +Rebuilding u-boot for Cyrus + +The Cyrus defconfigs are Cyrus_P5020_defconfig and Cyrus_P5040_defconfig. + +They currently disable size optimization in order to avoid a relocation +bug in some versions of GCC. As the output size is a constant, the size +optimization is not currently important. + +Cyrus boots off a microSD card in a slot on the motherboard. This requires +that the u-boot is built for the Pre-Boot Loader on the P5020/P5040. +In order to reflash u-boot, you must download u-boot.pbl, then write it +onto the card. To do that from u-boot: + +> tftp 1000000 u-boot.pbl +> mmc write 1000000 8 672 + +If you want to do this via a card reader in linux: + +> dd if=u-boot.pbl of=/dev/sdX bs=512 oseek=8 + + diff --git a/board/varisys/cyrus/cyrus.c b/board/varisys/cyrus/cyrus.c new file mode 100644 index 0000000..79c363c --- /dev/null +++ b/board/varisys/cyrus/cyrus.c @@ -0,0 +1,116 @@ +/* + * Based on corenet_ds.c + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <netdev.h> +#include <linux/compiler.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <fm_eth.h> +#include <pci.h> + +#include "cyrus.h" +#include "../common/eeprom.h" + +DECLARE_GLOBAL_DATA_PTR; + +#define GPIO_OPENDRAIN 0x30000000 +#define GPIO_DIR 0x3c000004 +#define GPIO_INITIAL 0x30000000 +#define GPIO_VGA_SWITCH 0x00001000 + +int checkboard(void) +{ + printf("Board: CYRUS\n"); + + return 0; +} + +int board_early_init_f(void) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR); + + /* + * Only use DDR1_MCK0/3 and DDR2_MCK0/3 + * disable DDR1_MCK1/2/4/5 and DDR2_MCK1/2/4/5 to reduce + * the noise introduced by these unterminated and unused clock pairs. + */ + setbits_be32(&gur->ddrclkdr, 0x001B001B); + + /* Set GPIO reset lines to open-drain, tristate */ + setbits_be32(&pgpio->gpdat, GPIO_INITIAL); + setbits_be32(&pgpio->gpodr, GPIO_OPENDRAIN); + + /* Set GPIO Direction */ + setbits_be32(&pgpio->gpdir, GPIO_DIR); + + return 0; +} + +int board_early_init_r(void) +{ + fsl_lbc_t *lbc = LBC_BASE_ADDR; + + out_be32(&lbc->lbcr, 0); + /* 1 clock LALE cycle */ + out_be32(&lbc->lcrr, 0x80000000 | CONFIG_SYS_LBC_LCRR); + + set_liodns(); + +#ifdef CONFIG_SYS_DPAA_QBMAN + setup_portals(); +#endif + print_lbc_regs(); + return 0; +} + +int misc_init_r(void) +{ + return 0; +} + +int ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); + fdt_fixup_dr_usb(blob, bd); + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); +#endif + + return 0; +} + +int mac_read_from_eeprom(void) +{ + init_eeprom(CONFIG_SYS_EEPROM_BUS_NUM, + CONFIG_SYS_I2C_EEPROM_ADDR, + CONFIG_SYS_I2C_EEPROM_ADDR_LEN); + + return mac_read_from_eeprom_common(); +} diff --git a/board/varisys/cyrus/cyrus.h b/board/varisys/cyrus/cyrus.h new file mode 100644 index 0000000..8cd52ba --- /dev/null +++ b/board/varisys/cyrus/cyrus.h @@ -0,0 +1,11 @@ +/* + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CYRUS_H +#define __CYRUS_H + +void fdt_fixup_board_enet(void *blob); +void pci_of_setup(void *blob, bd_t *bd); + +#endif diff --git a/board/varisys/cyrus/ddr.c b/board/varisys/cyrus/ddr.c new file mode 100644 index 0000000..bb1d29a --- /dev/null +++ b/board/varisys/cyrus/ddr.c @@ -0,0 +1,188 @@ +/* + * Based on corenet_ds ddr code + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <hwconfig.h> +#include <asm/mmu.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> +#include <asm/fsl_law.h> + +DECLARE_GLOBAL_DATA_PTR; + + +struct board_specific_parameters { + u32 n_ranks; + u32 datarate_mhz_high; + u32 clk_adjust; + u32 wrlvl_start; + u32 cpo; + u32 write_data_delay; + u32 force_2t; +}; + +/* + * This table contains all valid speeds we want to override with board + * specific parameters. datarate_mhz_high values need to be in ascending order + * for each n_ranks group. + */ +static const struct board_specific_parameters udimm0[] = { + /* + * memory controller 0 + * num| hi| clk| wrlvl | cpo |wrdata|2T + * ranks| mhz|adjst| start | |delay | + */ + {4, 850, 4, 6, 0xff, 2, 0}, + {4, 950, 5, 7, 0xff, 2, 0}, + {4, 1050, 5, 8, 0xff, 2, 0}, + {4, 1250, 5, 10, 0xff, 2, 0}, + {4, 1350, 5, 11, 0xff, 2, 0}, + {4, 1666, 5, 12, 0xff, 2, 0}, + {2, 850, 5, 6, 0xff, 2, 0}, + {2, 1050, 5, 7, 0xff, 2, 0}, + {2, 1250, 4, 6, 0xff, 2, 0}, + {2, 1350, 5, 7, 0xff, 2, 0}, + {2, 1666, 5, 8, 0xff, 2, 0}, + {1, 1250, 4, 6, 0xff, 2, 0}, + {1, 1335, 4, 7, 0xff, 2, 0}, + {1, 1666, 4, 8, 0xff, 2, 0}, + {} +}; + +/* + * The two slots have slightly different timing. The center values are good + * for both slots. We use identical speed tables for them. In future use, if + * DIMMs have fewer center values that require two separated tables, copy the + * udimm0 table to udimm1 and make changes to clk_adjust and wrlvl_start. + */ +static const struct board_specific_parameters *udimms[] = { + udimm0, + udimm0, +}; + +static const struct board_specific_parameters rdimm0[] = { + /* + * memory controller 0 + * num| hi| clk| wrlvl | cpo |wrdata|2T + * ranks| mhz|adjst| start | |delay | + */ + {4, 850, 4, 6, 0xff, 2, 0}, + {4, 950, 5, 7, 0xff, 2, 0}, + {4, 1050, 5, 8, 0xff, 2, 0}, + {4, 1250, 5, 10, 0xff, 2, 0}, + {4, 1350, 5, 11, 0xff, 2, 0}, + {4, 1666, 5, 12, 0xff, 2, 0}, + {2, 850, 4, 6, 0xff, 2, 0}, + {2, 1050, 4, 7, 0xff, 2, 0}, + {2, 1666, 4, 8, 0xff, 2, 0}, + {1, 850, 4, 5, 0xff, 2, 0}, + {1, 950, 4, 7, 0xff, 2, 0}, + {1, 1666, 4, 8, 0xff, 2, 0}, + {} +}; + +/* + * The two slots have slightly different timing. See comments above. + */ +static const struct board_specific_parameters *rdimms[] = { + rdimm0, + rdimm0, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; + ulong ddr_freq; + + if (ctrl_num > 1) { + printf("Wrong parameter for controller number %d", ctrl_num); + return; + } + if (!pdimm->n_ranks) + return; + + if (popts->registered_dimm_en) + pbsp = rdimms[ctrl_num]; + else + pbsp = udimms[ctrl_num]; + + + /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + while (pbsp->datarate_mhz_high) { + if (pbsp->n_ranks == pdimm->n_ranks) { + if (ddr_freq <= pbsp->datarate_mhz_high) { + popts->cpo_override = pbsp->cpo; + popts->write_data_delay = + pbsp->write_data_delay; + popts->clk_adjust = pbsp->clk_adjust; + popts->wrlvl_start = pbsp->wrlvl_start; + popts->twot_en = pbsp->force_2t; + goto found; + } + pbsp_highest = pbsp; + } + pbsp++; + } + + if (pbsp_highest) { + printf("Error: board specific timing not found for data rate %lu MT/s!\nTrying to use the highest speed (%u) parameters\n", + ddr_freq, pbsp_highest->datarate_mhz_high); + popts->cpo_override = pbsp_highest->cpo; + popts->write_data_delay = pbsp_highest->write_data_delay; + popts->clk_adjust = pbsp_highest->clk_adjust; + popts->wrlvl_start = pbsp_highest->wrlvl_start; + popts->twot_en = pbsp_highest->force_2t; + } else { + panic("DIMM is not supported by this board"); + } +found: + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * Rtt and Rtt_WR override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 60 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN; +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size; + + puts("Initializing...."); + + if (!fsl_use_spd()) + panic("Cyrus only supports using SPD for DRAM\n"); + + puts("using SPD\n"); + dram_size = fsl_ddr_sdram(); + + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; + + debug(" DDR: "); + return dram_size; +} diff --git a/board/varisys/cyrus/eth.c b/board/varisys/cyrus/eth.c new file mode 100644 index 0000000..bcadc67 --- /dev/null +++ b/board/varisys/cyrus/eth.c @@ -0,0 +1,100 @@ +/* + * Author Adrian Cox + * Based somewhat on board/freescale/corenet_ds/eth_hydra.c + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <netdev.h> +#include <asm/fsl_serdes.h> +#include <fm_eth.h> +#include <fsl_mdio.h> +#include <malloc.h> +#include <fdt_support.h> +#include <fsl_dtsec.h> + +#ifdef CONFIG_FMAN_ENET + +#define FIRST_PORT_ADDR 3 +#define SECOND_PORT_ADDR 7 + +#ifdef CONFIG_PPC_P5040 +#define FIRST_PORT FM1_DTSEC5 +#define SECOND_PORT FM2_DTSEC5 +#else +#define FIRST_PORT FM1_DTSEC4 +#define SECOND_PORT FM1_DTSEC5 +#endif + +#define IS_VALID_PORT(p) ((p) == FIRST_PORT || (p) == SECOND_PORT) + +static void cyrus_phy_tuning(int phy) +{ + /* + * Enable RGMII delay on Tx and Rx for CPU port + */ + printf("Tuning PHY @ %d\n", phy); + + /* sets address 0x104 or reg 260 for writing */ + miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0xb, 0x8104); + /* Sets RXC/TXC to +0.96ns and TX_CTL/RX_CTL to -0.84ns */ + miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0xc, 0xf0f0); + /* sets address 0x105 or reg 261 for writing */ + miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0xb, 0x8105); + /* writes to address 0x105 , RXD[3..0] to -0. */ + miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0xc, 0x0000); + /* sets address 0x106 or reg 261 for writing */ + miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0xb, 0x8106); + /* writes to address 0x106 , TXD[3..0] to -0.84ns */ + miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0xc, 0x0000); + /* force re-negotiation */ + miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0x0, 0x1340); +} +#endif + +int board_eth_init(bd_t *bis) +{ +#ifdef CONFIG_FMAN_ENET + struct fsl_pq_mdio_info dtsec_mdio_info; + unsigned int i; + + printf("Initializing Fman\n"); + + + /* Register the real 1G MDIO bus */ + dtsec_mdio_info.regs = + (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR; + dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + fsl_pq_mdio_init(bis, &dtsec_mdio_info); + + + fm_info_set_phy_address(FIRST_PORT, FIRST_PORT_ADDR); + fm_info_set_mdio(FIRST_PORT, + miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME)); + fm_info_set_phy_address(SECOND_PORT, SECOND_PORT_ADDR); + fm_info_set_mdio(SECOND_PORT, + miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME)); + + /* Never disable DTSEC1 - it controls MDIO */ + for (i = FM1_DTSEC2; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + if (!IS_VALID_PORT(i)) + fm_disable_port(i); + } + +#ifdef CONFIG_PPC_P5040 + for (i = FM2_DTSEC2; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) { + if (!IS_VALID_PORT(i)) + fm_disable_port(i); + } +#endif + + cpu_eth_init(bis); + + cyrus_phy_tuning(FIRST_PORT_ADDR); + cyrus_phy_tuning(SECOND_PORT_ADDR); +#endif + + return pci_eth_init(bis); +} diff --git a/board/varisys/cyrus/law.c b/board/varisys/cyrus/law.c new file mode 100644 index 0000000..91e1d85 --- /dev/null +++ b/board/varisys/cyrus/law.c @@ -0,0 +1,27 @@ +/* + * Author: Adrian Cox + * Based on corenet_ds law files. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_LBC0_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_LBC1_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_LBC), +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_QMAN), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + /* Limit DCSR to 32M to access NPC Trace Buffer */ + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/varisys/cyrus/pbi.cfg b/board/varisys/cyrus/pbi.cfg new file mode 100644 index 0000000..9b330dd --- /dev/null +++ b/board/varisys/cyrus/pbi.cfg @@ -0,0 +1,35 @@ +# +# Copyright 2012 Freescale Semiconductor, Inc. +# +# Refer docs/README.pblimage for more details about how-to configure +# and create PBL boot image +# +# SPDX-License-Identifier: GPL-2.0+ +# + +#PBI commands +#Initialize CPC1 as 1MB SRAM +09010000 00200400 +09138000 00000000 +091380c0 00000100 +09010100 00000000 +09010104 fff0000b +09010f00 08000000 +09010000 80000000 +#Configure LAW for CPC1 +09000d00 00000000 +09000d04 fff00000 +09000d08 81000013 +09000010 00000000 +09000014 ff000000 +09000018 81000000 +#Initialize eSPI controller, default configuration is slow for eSPI to +#load data, this configuration comes from u-boot eSPI driver. +09110000 80000403 +09110020 2d170008 +09110024 00100008 +09110028 00100008 +0911002c 00100008 +#Flush PBL data +09138000 00000000 +091380c0 00000000 diff --git a/board/varisys/cyrus/pci.c b/board/varisys/cyrus/pci.c new file mode 100644 index 0000000..4780e8c --- /dev/null +++ b/board/varisys/cyrus/pci.c @@ -0,0 +1,23 @@ +/* + * Copyright 2007-2011 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/fsl_pci.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <asm/fsl_serdes.h> + +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/varisys/cyrus/rcw_p5020_v2.cfg b/board/varisys/cyrus/rcw_p5020_v2.cfg new file mode 100644 index 0000000..9188080 --- /dev/null +++ b/board/varisys/cyrus/rcw_p5020_v2.cfg @@ -0,0 +1,11 @@ +# +# Default RCW for Cyrus P5020 +# + +#PBL preamble and RCW header +aa55aa55 010e0100 +#64 bytes RCW data +0c540000 00000000 1e1e0000 00000000 +44808c00 ff002000 68000000 45000000 +00000000 00000000 00000000 0003000f +a0000000 00000000 00000000 00000000 diff --git a/board/varisys/cyrus/rcw_p5040.cfg b/board/varisys/cyrus/rcw_p5040.cfg new file mode 100644 index 0000000..5284481 --- /dev/null +++ b/board/varisys/cyrus/rcw_p5040.cfg @@ -0,0 +1,11 @@ +# +# Default RCW for Cyrus P5040 +# + +#PBL preamble and RCW header +aa55aa55 010e0100 +#64 bytes RCW data +90e00000 00000000 acac9800 00440000 +44808c00 ff29a000 68000000 61000000 +00000000 00000000 00000000 0003000f +a0000000 00000000 00000000 00000000 diff --git a/board/varisys/cyrus/tlb.c b/board/varisys/cyrus/tlb.c new file mode 100644 index 0000000..3fa5864 --- /dev/null +++ b/board/varisys/cyrus/tlb.c @@ -0,0 +1,106 @@ +/* + * Author: Adrian Cox + * Based on corenet_ds tlb code + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ +#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) + /* + * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the + * SRAM is at 0xfff00000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_1M, 1), +#else + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#endif + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + + /* Local Bus */ + SET_TLB_ENTRY(1, CONFIG_SYS_LBC0_BASE, CONFIG_SYS_LBC0_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_64K, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_LBC1_BASE, CONFIG_SYS_LBC1_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_4K, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x40000000, + CONFIG_SYS_PCIE1_MEM_PHYS + 0x40000000, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x50000000, + CONFIG_SYS_PCIE1_MEM_PHYS + 0x50000000, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_256K, 1), + + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SW|MAS3_SR, 0, + 0, 9, BOOKE_PAGESZ_1M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_1M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SW|MAS3_SR, 0, + 0, 11, BOOKE_PAGESZ_1M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 12, BOOKE_PAGESZ_1M, 1), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 13, BOOKE_PAGESZ_4M, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/configs/Cyrus_P5020_defconfig b/configs/Cyrus_P5020_defconfig new file mode 100644 index 0000000..d9bee34 --- /dev/null +++ b/configs/Cyrus_P5020_defconfig @@ -0,0 +1,9 @@ +CONFIG_PPC=y +CONFIG_MPC85xx=y +CONFIG_TARGET_CYRUS=y +CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SYS_TEXT_BASE=0xFFF40000,PPC_P5020" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_NETDEVICES=y +CONFIG_E1000=y diff --git a/configs/Cyrus_P5040_defconfig b/configs/Cyrus_P5040_defconfig new file mode 100644 index 0000000..c66238a --- /dev/null +++ b/configs/Cyrus_P5040_defconfig @@ -0,0 +1,9 @@ +CONFIG_PPC=y +CONFIG_MPC85xx=y +CONFIG_TARGET_CYRUS=y +CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SYS_TEXT_BASE=0xFFF40000,PPC_P5040" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_NETDEVICES=y +CONFIG_E1000=y diff --git a/include/configs/cyrus.h b/include/configs/cyrus.h new file mode 100644 index 0000000..c0959c1 --- /dev/null +++ b/include/configs/cyrus.h @@ -0,0 +1,588 @@ +/* + * Based on corenet_ds.h + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_DISPLAY_BOARDINFO + +#define CONFIG_CYRUS + +#define CONFIG_PHYS_64BIT + +#if !defined(CONFIG_PPC_P5020) && !defined(CONFIG_PPC_P5040) +#error Must call Cyrus CONFIG with a specific CPU enabled. +#endif + + +#define CONFIG_MMC +#define CONFIG_SDCARD +#define CONFIG_FSL_SATA_V2 +#define CONFIG_PCIE3 +#define CONFIG_PCIE4 +#ifdef CONFIG_PPC_P5020 +#define CONFIG_SYS_FSL_RAID_ENGINE +#define CONFIG_SYS_DPAA_RMAN +#endif +#define CONFIG_SYS_DPAA_PME + +/* + * Corenet DS style board configuration file + */ +#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_SYS_FSL_PBL_PBI board/varisys/cyrus/pbi.cfg +#if defined(CONFIG_PPC_P5020) +#define CONFIG_SYS_CLK_FREQ 133000000 +#define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5020_v2.cfg +#elif defined(CONFIG_PPC_P5040) +#define CONFIG_SYS_CLK_FREQ 100000000 +#define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5040.cfg +#endif + + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_E500MC /* BOOKE e500mc family */ +#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ +#define CONFIG_MP /* support multiple processors */ + + +#define CONFIG_SYS_MMC_MAX_DEVICE 1 + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff40000 +#endif + +#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ +#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS +#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_PCIE2 /* PCIE controler 2 */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_SYS_NO_FLASH + +#if defined(CONFIG_SDCARD) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_FSL_FIXED_MMC_LOCATION +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_OFFSET (512 * 1658) +#endif + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_SYS_CACHE_STASHING +#define CONFIG_BACKSIDE_L2_CACHE +#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_DDR_ECC +#ifdef CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#endif + +#define CONFIG_ENABLE_36BIT_PHYS + +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ +#endif + +/* test POST memory test */ +#undef CONFIG_POST +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* + * Config the L3 Cache as L3 SRAM + */ +#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | CONFIG_RAMBOOT_TEXT_BASE) +#else +#define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR +#endif +#define CONFIG_SYS_L3_SIZE (1024 << 10) +#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) + +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_DCSRBAR 0xf0000000 +#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull +#endif + +/* + * DDR Setup + */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) + +#define CONFIG_DDR_SPD +#define CONFIG_SYS_FSL_DDR3 + +#define CONFIG_SYS_SPD_BUS_NUM 1 +#define SPD_EEPROM_ADDRESS1 0x51 +#define SPD_EEPROM_ADDRESS2 0x52 +#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ + +/* + * Local Bus Definitions + */ + +#define CONFIG_SYS_LBC0_BASE 0xe0000000 /* Start of LBC Registers */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_LBC0_BASE_PHYS 0xfe0000000ull +#else +#define CONFIG_SYS_LBC0_BASE_PHYS CONFIG_SYS_LBC0_BASE +#endif + +#define CONFIG_SYS_LBC1_BASE 0xe1000000 /* Start of LBC Registers */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_LBC1_BASE_PHYS 0xfe1000000ull +#else +#define CONFIG_SYS_LBC1_BASE_PHYS CONFIG_SYS_LBC1_BASE +#endif + +/* Set the local bus clock 1/16 of platform clock */ +#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_16 | LCRR_EADC_1) + +#define CONFIG_SYS_BR0_PRELIM \ +(BR_PHYS_ADDR(CONFIG_SYS_LBC0_BASE_PHYS) | BR_PS_16 | BR_V) +#define CONFIG_SYS_BR1_PRELIM \ +(BR_PHYS_ADDR(CONFIG_SYS_LBC1_BASE_PHYS) | BR_PS_16 | BR_V) + +#define CONFIG_SYS_OR0_PRELIM 0xfff00010 +#define CONFIG_SYS_OR1_PRELIM 0xfff00010 + + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +#if defined(CONFIG_RAMBOOT_PBL) +#define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ +#define CONFIG_MISC_INIT_R + +#define CONFIG_HWCONFIG + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#else +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS +#endif +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (768 * 1024) +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) + +#define CONFIG_SYS_BAUDRATE_TABLE \ +{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 +#define CONFIG_SYS_FSL_I2C3_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 +#define CONFIG_SYS_FSL_I2C4_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 + +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 + +#define CONFIG_SYS_I2C_GENERIC_MAC +#define CONFIG_SYS_I2C_MAC1_BUS 3 +#define CONFIG_SYS_I2C_MAC1_CHIP_ADDR 0x57 +#define CONFIG_SYS_I2C_MAC1_DATA_ADDR 0xf2 +#define CONFIG_SYS_I2C_MAC2_BUS 0 +#define CONFIG_SYS_I2C_MAC2_CHIP_ADDR 0x50 +#define CONFIG_SYS_I2C_MAC2_DATA_ADDR 0xfa + +#define CONFIG_CMD_DATE 1 +#define CONFIG_RTC_MCP79411 1 +#define CONFIG_SYS_RTC_BUS_NUM 3 +#define CONFIG_SYS_I2C_RTC_ADDR 0x6f + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_FSL_ESPI + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 1, direct to uli, tgtid 3, Base address 20000 */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#else +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 +#endif +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull +#else +#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 +#endif +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +/* controller 2, Slot 2, tgtid 2, Base address 201000 */ +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull +#else +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 +#endif +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull +#else +#define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000 +#endif +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ + +/* controller 3, Slot 1, tgtid 1, Base address 202000 */ +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull +#else +#define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000 +#endif +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull +#else +#define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000 +#endif +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ + +/* controller 4, Base address 203000 */ +#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull +#define CONFIG_SYS_PCIE4_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull +#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ + +/* Qman/Bman */ +#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ +#define CONFIG_SYS_BMAN_NUM_PORTALS 10 +#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull +#else +#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE +#endif +#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 +#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 +#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 +#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE +#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) +#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ + CONFIG_SYS_BMAN_CENA_SIZE) +#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) +#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 +#define CONFIG_SYS_QMAN_NUM_PORTALS 10 +#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull +#else +#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE +#endif +#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 +#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 +#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 +#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE +#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) +#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ + CONFIG_SYS_QMAN_CENA_SIZE) +#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) +#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 + +#define CONFIG_SYS_DPAA_FMAN +/* Default address of microcode for the Linux Fman driver */ +/* + * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is + * about 825KB (1650 blocks), Env is stored after the image, and the env size is + * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_MMC +#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680) + +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) + +#ifdef CONFIG_SYS_DPAA_FMAN +#define CONFIG_FMAN_ENET +#define CONFIG_PHY_MICREL +#define CONFIG_PHY_MICREL_KSZ9021 +#endif + +#ifdef CONFIG_PCI +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_NET_MULTI + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif /* CONFIG_PCI */ + +/* SATA */ +#ifdef CONFIG_FSL_SATA_V2 +#define CONFIG_LIBATA +#define CONFIG_FSL_SATA + +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SATA2 +#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA + +#define CONFIG_LBA48 +#define CONFIG_CMD_SATA +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +#endif + +#ifdef CONFIG_FMAN_ENET +#define CONFIG_SYS_TBIPA_VALUE 8 +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC4" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* + * Environment + */ +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * Command line configuration. + */ +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ERRATA +#define CONFIG_CMD_GREPENV +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#endif + +/* + * USB + */ +#define CONFIG_HAS_FSL_DR_USB +#define CONFIG_HAS_FSL_MPH_USB + +#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_CMD_EXT2 +#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_KEYBOARD +#define CONFIG_SYS_USB_EVENT_POLL + /* _VIA_CONTROL_EP */ +#define CONFIG_CONSOLE_MUX +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#endif + +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ + +#define CONFIG_BAUDRATE 115200 + +#define __USB_PHY_TYPE utmi + +#define CONFIG_EXTRA_ENV_SETTINGS \ +"hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ +"bank_intlv=cs0_cs1;" \ +"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\ +"usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ +"netdev=eth0\0" \ +"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ +"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ +"consoledev=ttyS0\0" \ +"ramdiskaddr=2000000\0" \ +"fdtaddr=c00000\0" \ +"bdev=sda3\0" + +#define CONFIG_HDBOOT \ +"setenv bootargs root=/dev/$bdev rw " \ +"console=$consoledev,$baudrate $othbootargs;" \ +"tftp $loadaddr $bootfile;" \ +"tftp $fdtaddr $fdtfile;" \ +"bootm $loadaddr - $fdtaddr" + +#define CONFIG_NFSBOOTCOMMAND \ +"setenv bootargs root=/dev/nfs rw " \ +"nfsroot=$serverip:$rootpath " \ +"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ +"console=$consoledev,$baudrate $othbootargs;" \ +"tftp $loadaddr $bootfile;" \ +"tftp $fdtaddr $fdtfile;" \ +"bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ +"setenv bootargs root=/dev/ram rw " \ +"console=$consoledev,$baudrate $othbootargs;" \ +"tftp $ramdiskaddr $ramdiskfile;" \ +"tftp $loadaddr $bootfile;" \ +"tftp $fdtaddr $fdtfile;" \ +"bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT + +#include <asm/fsl_secure_boot.h> + +#ifdef CONFIG_SECURE_BOOT +#endif + +#endif /* __CONFIG_H */ + -- 1.9.1

2 2

[U-Boot] [PATCH 1/8] net: zynq: Allocate BD_SPACE in connection to RX_BUF
by Michal Simek 04 Nov '15

04 Nov '15

BD_SEPRN_SPACE should not have hard coded value and it will be calculated based on the number of buffer descriptors that we would like to use. Signed-off-by: Michal Simek <michal.simek(a)xilinx.com> --- drivers/net/zynq_gem.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/zynq_gem.c b/drivers/net/zynq_gem.c index 0e741dd605a6..5aa21b9f24a7 100644 --- a/drivers/net/zynq_gem.c +++ b/drivers/net/zynq_gem.c @@ -149,7 +149,7 @@ struct emac_bd { */ #define BD_SPACE 0x100000 /* BD separation space */ -#define BD_SEPRN_SPACE 64 +#define BD_SEPRN_SPACE (RX_BUF * sizeof(struct emac_bd)) /* Initialized, rxbd_current, rx_first_buf must be 0 after init */ struct zynq_gem_priv { -- 2.5.0

2 18

[U-Boot] [ANN] U-Boot v2015.10-rc5 released
by Tom Rini 04 Nov '15

04 Nov '15

Hey all, Today is the scheduled release date for v2015.10. But as you can tell from the list of patches I just merged, a lot of stuff needed to go in still and while I'm "happy" it's all safe it's also too much to not do another -rc. So here we are and I'm expecting to do the release next Monday. So please, test this. If you have a regression, speak up. If you have a bugfix, speak up. And to the maintainers, if you want to start on your "next" branch now so that you can just rebase it to master next week, that might not be a bad idea. I might even do that myself (but please keep your stuff based on my master). Thanks! -- Tom

7 12

[U-Boot] [PATCH v2 0/5] ARM: omap-common: Add board detection support for TI EVMs
by Steve Kipisz 04 Nov '15

04 Nov '15

Several TI EVMs have onboard EEPROM that contain board description information. The onboard EEPROM on Beaglebone, Beaglebone Black, AM335x EVM, AM43x EVM, AM57xx EVM, Beagleboard-x15 all share the same format. This series of patches introduces code which is generic among these platforms. The boards can use the data for any operations they might choose. Lokesh Vutla (1): ARM: omap-common: Add standard access for board description EEPROM Steve Kipisz (4): ARM: OMAP4/5: Centralize early clock initialization ARM: OMAP4/5: Centralize gpi2c_init ARM: OMAP4/5: Add generic board detection hook board: ti: AM57xx: Add detection logic for AM57xx-evm arch/arm/cpu/armv7/omap-common/Makefile | 1 + arch/arm/cpu/armv7/omap-common/clocks-common.c | 26 ++++- arch/arm/cpu/armv7/omap-common/hwinit-common.c | 14 ++- arch/arm/cpu/armv7/omap-common/ti-i2c-eeprom.c | 148 +++++++++++++++++++++++++ arch/arm/include/asm/arch-omap4/sys_proto.h | 4 +- arch/arm/include/asm/arch-omap5/sys_proto.h | 4 +- arch/arm/include/asm/omap_common.h | 133 +++++++++++++++++++++- board/ti/am57xx/board.c | 53 +++++++++ include/configs/am57xx_evm.h | 4 + include/configs/ti_omap5_common.h | 2 + 10 files changed, 380 insertions(+), 9 deletions(-) create mode 100644 arch/arm/cpu/armv7/omap-common/ti-i2c-eeprom.c -- 1.9.1

6 24

[U-Boot] [PATCH] ARM: zynq: Remove zc70x target
by Michal Simek 04 Nov '15

04 Nov '15

Remove zc70x target which was one setting for zc702 and zc706. Currently zc702 and zc706 are separated. Signed-off-by: Michal Simek <michal.simek(a)xilinx.com> --- arch/arm/mach-zynq/Kconfig | 10 +--------- board/xilinx/zynq/Makefile | 10 ---------- configs/zynq_zc70x_defconfig | 15 --------------- 3 files changed, 1 insertion(+), 34 deletions(-) delete mode 100644 configs/zynq_zc70x_defconfig diff --git a/arch/arm/mach-zynq/Kconfig b/arch/arm/mach-zynq/Kconfig index 7a1aec45e79a..afe6cc3eddb5 100644 --- a/arch/arm/mach-zynq/Kconfig +++ b/arch/arm/mach-zynq/Kconfig @@ -21,13 +21,6 @@ config TARGET_ZYNQ_MICROZED config TARGET_ZYNQ_PICOZED bool "Zynq PicoZed" -config TARGET_ZYNQ_ZC70X - bool "Zynq ZC702/ZC706 Board (deprecated)" - select ZYNQ_CUSTOM_INIT - help - This option is deprecated. Use TARGET_ZYNQ_ZC702 - or TARGET_ZYNQ_706. - config TARGET_ZYNQ_ZC702 bool "Zynq ZC702 Board" @@ -57,8 +50,7 @@ config SYS_CONFIG_NAME default "zynq_zed" if TARGET_ZYNQ_ZED default "zynq_microzed" if TARGET_ZYNQ_MICROZED default "zynq_picozed" if TARGET_ZYNQ_PICOZED - default "zynq_zc70x" if TARGET_ZYNQ_ZC702 || TARGET_ZYNQ_ZC706 \ - || TARGET_ZYNQ_ZC70X + default "zynq_zc70x" if TARGET_ZYNQ_ZC702 || TARGET_ZYNQ_ZC706 default "zynq_zc770" if TARGET_ZYNQ_ZC770 default "zynq_zybo" if TARGET_ZYNQ_ZYBO diff --git a/board/xilinx/zynq/Makefile b/board/xilinx/zynq/Makefile index fd5d6fe950c7..88047ec1de43 100644 --- a/board/xilinx/zynq/Makefile +++ b/board/xilinx/zynq/Makefile @@ -36,13 +36,3 @@ CFLAGS_REMOVE_ps7_init_gpl.o := -Wstrict-prototypes # To include xil_io.h CFLAGS_ps7_init_gpl.o := -I$(srctree)/$(src) - -# Warn if CONFIG_TARGET_ZYNQ_ZC70X is enabled -ifeq ($(CONFIG_TARGET_ZYNQ_ZC70X),y) -ifeq ($(CONFIG_SPL_BUILD),y) -$(warning CONFIG_TARGET_ZYNQ_ZC70X is deprecated.) -$(warning Enable CONFIG_TARGET_ZYNQ_ZC702 or CONFIG_TARGET_ZYNQ_706 instead.) -$(warning "make zynq_zc70x_defconfig" is also deprecated.) -$(warning Use "make zynq_zc702_defconfig" or "make zynq_zc706_defconfig".) -endif -endif diff --git a/configs/zynq_zc70x_defconfig b/configs/zynq_zc70x_defconfig deleted file mode 100644 index 5d702b2f1d85..000000000000 --- a/configs/zynq_zc70x_defconfig +++ /dev/null @@ -1,15 +0,0 @@ -CONFIG_ARM=y -CONFIG_ARCH_ZYNQ=y -CONFIG_TARGET_ZYNQ_ZC70X=y -CONFIG_DEFAULT_DEVICE_TREE="zynq-zc702" -CONFIG_SPL=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_FIT_SIGNATURE=y -# CONFIG_CMD_IMLS is not set -# CONFIG_CMD_FLASH is not set -# CONFIG_CMD_SETEXPR is not set -CONFIG_OF_SEPARATE=y -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_SPI_FLASH=y -CONFIG_ZYNQ_QSPI=y -- 2.5.0

3 2

[U-Boot] Pull request: u-boot-spi/next
by Jagan Teki 04 Nov '15

04 Nov '15

Hi Tom, Please pull this series. thanks! Jagan. The following changes since commit 96d59e9d6aa74e35c63dc74da10e41f8ba0f6de4: mpc85xx/t2081: enable parsing DDR ratio for T2081 rev1.1 (2015-11-02 08:51:50 -0800) are available in the git repository at: git://git.denx.de/u-boot-spi.git next for you to fetch changes up to e39e68f155b4fcd47f62ab2cf0e199d04f38446d: sf: Add SPI NOR protection mechanism (2015-11-03 21:51:37 +0530) ---------------------------------------------------------------- Fabio Estevam (16): include: Add log2 header from the kernel include: Add generic bitops headers ARM: bitops: Use the generic bitops headers x86: bitops: Use the generic bitops headers m68k: bitops: Use the generic bitops headers blackfin: bitops: Use the generic bitops headers sh: bitops: Use the generic bitops headers sandbox: Use the generic bitops headers sparc: Use the generic bitops headers openrisc: Use the generic bitops headers nds32: Use the generic bitops headers nios2: Use the generic bitops headers compat: Remove is_power_of_2() definition powerpc: Remove __ilog2_u64 and ffs4 from bitops sf: Add SPI protection mechanism from the kernel sf: Add SPI NOR protection mechanism arch/arm/include/asm/bitops.h | 5 + arch/arm/mach-mvebu/mbus.c | 2 +- arch/blackfin/include/asm/bitops.h | 4 + arch/m68k/include/asm/bitops.h | 4 + arch/microblaze/include/asm/bitops.h | 4 + arch/nds32/include/asm/bitops.h | 4 + arch/nios2/include/asm/bitops.h | 5 + arch/openrisc/include/asm/bitops.h | 4 + arch/powerpc/cpu/mpc83xx/law.c | 5 +- arch/powerpc/cpu/mpc85xx/tlb.c | 2 + arch/powerpc/cpu/mpc8xxx/law.c | 5 +- arch/powerpc/include/asm/bitops.h | 11 +- arch/powerpc/include/asm/fsl_law.h | 1 + arch/powerpc/include/asm/fsl_srio.h | 2 + arch/sandbox/include/asm/bitops.h | 4 + arch/sh/include/asm/bitops.h | 5 + arch/sparc/include/asm/bitops.h | 5 + arch/x86/include/asm/bitops.h | 21 +++- common/cmd_sf.c | 35 ++++++ drivers/mtd/mtdcore.c | 2 +- drivers/mtd/spi/sf_internal.h | 12 ++ drivers/mtd/spi/sf_ops.c | 180 ++++++++++++++++++++++++++++++ drivers/mtd/spi/sf_probe.c | 13 +++ drivers/mtd/ubi/build.c | 2 +- fs/ubifs/super.c | 2 +- include/asm-generic/bitops/__ffs.h | 43 ++++++++ include/asm-generic/bitops/__fls.h | 43 ++++++++ include/asm-generic/bitops/fls.h | 41 +++++++ include/asm-generic/bitops/fls64.h | 36 ++++++ include/linux/bitops.h | 27 +++++ include/linux/compat.h | 6 - include/linux/log2.h | 205 +++++++++++++++++++++++++++++++++++ include/spi_flash.h | 19 ++++ 33 files changed, 734 insertions(+), 25 deletions(-) create mode 100644 include/asm-generic/bitops/__ffs.h create mode 100644 include/asm-generic/bitops/__fls.h create mode 100644 include/asm-generic/bitops/fls.h create mode 100644 include/asm-generic/bitops/fls64.h create mode 100644 include/linux/log2.h

4 11

[U-Boot] [PATCH v5 1/6] cgtqmx6eval: Add SPI NOR flash support
by Otavio Salvador 03 Nov '15

03 Nov '15

Add SPI NOR support: => sf probe SF: Detected SST25VF032B with page size 256 Bytes, erase size 4 KiB, total 4 MiB Signed-off-by: Otavio Salvador <otavio(a)ossystems.com.br> --- Changes in v5: None Changes in v4: None board/congatec/cgtqmx6eval/cgtqmx6eval.c | 23 +++++++++++++++++++++++ include/configs/cgtqmx6eval.h | 12 ++++++++++++ 2 files changed, 35 insertions(+) diff --git a/board/congatec/cgtqmx6eval/cgtqmx6eval.c b/board/congatec/cgtqmx6eval/cgtqmx6eval.c index cf5607b..18e408b 100644 --- a/board/congatec/cgtqmx6eval/cgtqmx6eval.c +++ b/board/congatec/cgtqmx6eval/cgtqmx6eval.c @@ -45,6 +45,10 @@ DECLARE_GLOBAL_DATA_PTR; PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ PAD_CTL_ODE | PAD_CTL_SRE_FAST) +#define SPI_PAD_CTRL (PAD_CTL_HYS | \ + PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) + #define MX6Q_QMX6_PFUZE_MUX IMX_GPIO_NR(6, 9) @@ -152,6 +156,13 @@ static iomux_v3_cfg_t enet_pads_ar8035[] = { MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), }; +static iomux_v3_cfg_t const ecspi1_pads[] = { + MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + #define PC MUX_PAD_CTRL(I2C_PAD_CTRL) struct i2c_pads_info i2c_pad_info1 = { .scl = { @@ -381,6 +392,12 @@ static void setup_iomux_uart(void) imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads)); } +void setup_spinor(void) +{ + imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); + gpio_direction_output(IMX_GPIO_NR(3, 19), 0); +} + #ifdef CONFIG_FSL_ESDHC static struct fsl_esdhc_cfg usdhc_cfg[] = { {USDHC2_BASE_ADDR}, @@ -646,6 +663,7 @@ int board_early_init_f(void) { setup_iomux_uart(); setup_display(); + setup_spinor(); return 0; } @@ -671,6 +689,11 @@ int checkboard(void) return 0; } +int board_spi_cs_gpio(unsigned bus, unsigned cs) +{ + return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(3, 19)) : -EINVAL; +} + #ifdef CONFIG_CMD_BMODE static const struct boot_mode board_boot_modes[] = { /* 4 bit bus width */ diff --git a/include/configs/cgtqmx6eval.h b/include/configs/cgtqmx6eval.h index e0aa4b0..9aa66c7 100644 --- a/include/configs/cgtqmx6eval.h +++ b/include/configs/cgtqmx6eval.h @@ -29,6 +29,16 @@ /* MMC Configs */ #define CONFIG_SYS_FSL_ESDHC_ADDR 0 +/* SPI NOR */ +#define CONFIG_CMD_SF +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SPI_FLASH_SST +#define CONFIG_MXC_SPI +#define CONFIG_SF_DEFAULT_BUS 0 +#define CONFIG_SF_DEFAULT_SPEED 20000000 +#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0) + /* Miscellaneous commands */ #define CONFIG_CMD_BMODE @@ -200,8 +210,10 @@ "else " \ "bootz; " \ "fi;\0" \ + "spilock=sf probe && sf protect lock 0x3f0000 0x10000;"\ #define CONFIG_BOOTCOMMAND \ + "run spilock;" \ "mmc dev ${mmcdev};" \ "if mmc rescan; then " \ "if run loadbootscript; then " \ -- 2.6.2

4 13

[U-Boot] [PATCH v6 15/16] sf: Add SPI protection mechanism from the kernel
by Jagan Teki 03 Nov '15

03 Nov '15

From: Fabio Estevam <fabio.estevam(a)freescale.com> Add the SPI NOR protection mechanism from the kernel. This code is based on the work from Brian Norris <computersforpeace(a)gmail.com> Here is the commit details. "mtd: spi-nor: refactor block protection functions" (sha1: 62593cf40b23b523b9fc9334ca61ba6c595ebb09) Signed-off-by: Fabio Estevam <fabio.estevam(a)freescale.com> [Added more details to commit message] Signed-off-by: Jagan Teki <jteki(a)openedev.com> Reviewed-by: Tom Rini <trini(a)konsulko.com> Reviewed-by: Heiko Schocher <hs(a)denx.de> Reviewed-by: Jagan Teki <jteki(a)openedev.com> --- Changes for v2: - Updated commit message drivers/mtd/spi/sf_internal.h | 3 + drivers/mtd/spi/sf_ops.c | 170 ++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 173 insertions(+) diff --git a/drivers/mtd/spi/sf_internal.h b/drivers/mtd/spi/sf_internal.h index 8a3e5ec..ac493f1 100644 --- a/drivers/mtd/spi/sf_internal.h +++ b/drivers/mtd/spi/sf_internal.h @@ -105,6 +105,9 @@ enum spi_nor_option_flags { #define STATUS_QEB_WINSPAN (1 << 1) #define STATUS_QEB_MXIC (1 << 6) #define STATUS_PEC (1 << 7) +#define SR_BP0 BIT(2) /* Block protect 0 */ +#define SR_BP1 BIT(3) /* Block protect 1 */ +#define SR_BP2 BIT(4) /* Block protect 2 */ /* Flash timeout values */ #define SPI_FLASH_PROG_TIMEOUT (2 * CONFIG_SYS_HZ) diff --git a/drivers/mtd/spi/sf_ops.c b/drivers/mtd/spi/sf_ops.c index f2a9244..4ada13f 100644 --- a/drivers/mtd/spi/sf_ops.c +++ b/drivers/mtd/spi/sf_ops.c @@ -15,6 +15,7 @@ #include <spi_flash.h> #include <watchdog.h> #include <linux/compiler.h> +#include <linux/log2.h> #include "sf_internal.h" @@ -565,3 +566,172 @@ int sst_write_bp(struct spi_flash *flash, u32 offset, size_t len, return ret; } #endif + +#ifdef CONFIG_SPI_FLASH_STMICRO +static void stm_get_locked_range(struct spi_flash *flash, u8 sr, loff_t *ofs, + u32 *len) +{ + u8 mask = SR_BP2 | SR_BP1 | SR_BP0; + int shift = ffs(mask) - 1; + int pow; + + if (!(sr & mask)) { + /* No protection */ + *ofs = 0; + *len = 0; + } else { + pow = ((sr & mask) ^ mask) >> shift; + *len = flash->size >> pow; + *ofs = flash->size - *len; + } +} + +/* + * Return 1 if the entire region is locked, 0 otherwise + */ +static int stm_is_locked_sr(struct spi_flash *flash, loff_t ofs, u32 len, + u8 sr) +{ + loff_t lock_offs; + u32 lock_len; + + stm_get_locked_range(flash, sr, &lock_offs, &lock_len); + + return (ofs + len <= lock_offs + lock_len) && (ofs >= lock_offs); +} + +/* + * Check if a region of the flash is (completely) locked. See stm_lock() for + * more info. + * + * Returns 1 if entire region is locked, 0 if any portion is unlocked, and + * negative on errors. + */ +int stm_is_locked(struct spi_flash *flash, loff_t ofs, u32 len) +{ + int status; + u8 sr; + + status = spi_flash_cmd_read_status(flash, &sr); + if (status < 0) + return status; + + return stm_is_locked_sr(flash, ofs, len, sr); +} + +/* + * Lock a region of the flash. Compatible with ST Micro and similar flash. + * Supports only the block protection bits BP{0,1,2} in the status register + * (SR). Does not support these features found in newer SR bitfields: + * - TB: top/bottom protect - only handle TB=0 (top protect) + * - SEC: sector/block protect - only handle SEC=0 (block protect) + * - CMP: complement protect - only support CMP=0 (range is not complemented) + * + * Sample table portion for 8MB flash (Winbond w25q64fw): + * + * SEC | TB | BP2 | BP1 | BP0 | Prot Length | Protected Portion + * -------------------------------------------------------------------------- + * X | X | 0 | 0 | 0 | NONE | NONE + * 0 | 0 | 0 | 0 | 1 | 128 KB | Upper 1/64 + * 0 | 0 | 0 | 1 | 0 | 256 KB | Upper 1/32 + * 0 | 0 | 0 | 1 | 1 | 512 KB | Upper 1/16 + * 0 | 0 | 1 | 0 | 0 | 1 MB | Upper 1/8 + * 0 | 0 | 1 | 0 | 1 | 2 MB | Upper 1/4 + * 0 | 0 | 1 | 1 | 0 | 4 MB | Upper 1/2 + * X | X | 1 | 1 | 1 | 8 MB | ALL + * + * Returns negative on errors, 0 on success. + */ +int stm_lock(struct spi_flash *flash, u32 ofs, u32 len) +{ + u8 status_old, status_new; + u8 mask = SR_BP2 | SR_BP1 | SR_BP0; + u8 shift = ffs(mask) - 1, pow, val; + + spi_flash_cmd_read_status(flash, &status_old); + + /* SPI NOR always locks to the end */ + if (ofs + len != flash->size) { + /* Does combined region extend to end? */ + if (!stm_is_locked_sr(flash, ofs + len, flash->size - ofs - len, + status_old)) + return -EINVAL; + len = flash->size - ofs; + } + + /* + * Need smallest pow such that: + * + * 1 / (2^pow) <= (len / size) + * + * so (assuming power-of-2 size) we do: + * + * pow = ceil(log2(size / len)) = log2(size) - floor(log2(len)) + */ + pow = ilog2(flash->size) - ilog2(len); + val = mask - (pow << shift); + if (val & ~mask) + return -EINVAL; + + /* Don't "lock" with no region! */ + if (!(val & mask)) + return -EINVAL; + + status_new = (status_old & ~mask) | val; + + /* Only modify protection if it will not unlock other areas */ + if ((status_new & mask) <= (status_old & mask)) + return -EINVAL; + + spi_flash_cmd_write_status(flash, status_new); + + return 0; +} + +/* + * Unlock a region of the flash. See stm_lock() for more info + * + * Returns negative on errors, 0 on success. + */ +int stm_unlock(struct spi_flash *flash, u32 ofs, u32 len) +{ + uint8_t status_old, status_new; + u8 mask = SR_BP2 | SR_BP1 | SR_BP0; + u8 shift = ffs(mask) - 1, pow, val; + + spi_flash_cmd_read_status(flash, &status_old); + + /* Cannot unlock; would unlock larger region than requested */ + if (stm_is_locked_sr(flash, status_old, ofs - flash->erase_size, + flash->erase_size)) + return -EINVAL; + /* + * Need largest pow such that: + * + * 1 / (2^pow) >= (len / size) + * + * so (assuming power-of-2 size) we do: + * + * pow = floor(log2(size / len)) = log2(size) - ceil(log2(len)) + */ + pow = ilog2(flash->size) - order_base_2(flash->size - (ofs + len)); + if (ofs + len == flash->size) { + val = 0; /* fully unlocked */ + } else { + val = mask - (pow << shift); + /* Some power-of-two sizes are not supported */ + if (val & ~mask) + return -EINVAL; + } + + status_new = (status_old & ~mask) | val; + + /* Only modify protection if it will not lock other areas */ + if ((status_new & mask) >= (status_old & mask)) + return -EINVAL; + + spi_flash_cmd_write_status(flash, status_new); + + return 0; +} +#endif /* CONFIG_SPI_FLASH_STMICRO */ -- 1.9.1

2 5

[U-Boot] [PATCH] arm: socfpga: reset: correct dma, qspi, and sdmmc reset bit defines
by dinguyen＠opensource.altera.com 03 Nov '15

03 Nov '15

From: Dinh Nguyen <dinguyen(a)opensource.altera.com> The DMA, QSPI, and SD/MMC reset bits are located in the permodrst register, not the mpumodrst. So the bank for these reset bits should be 1, not 0. Signed-off-by: Dinh Nguyen <dinguyen(a)opensource.altera.com> --- arch/arm/mach-socfpga/include/mach/reset_manager.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/mach-socfpga/include/mach/reset_manager.h b/arch/arm/mach-socfpga/include/mach/reset_manager.h index 8e59578..666a2ef 100644 --- a/arch/arm/mach-socfpga/include/mach/reset_manager.h +++ b/arch/arm/mach-socfpga/include/mach/reset_manager.h @@ -69,9 +69,9 @@ struct socfpga_reset_manager { #define RSTMGR_UART0 RSTMGR_DEFINE(1, 16) #define RSTMGR_SPIM0 RSTMGR_DEFINE(1, 18) #define RSTMGR_SPIM1 RSTMGR_DEFINE(1, 19) -#define RSTMGR_QSPI RSTMGR_DEFINE(0, 5) -#define RSTMGR_SDMMC RSTMGR_DEFINE(0, 22) -#define RSTMGR_DMA RSTMGR_DEFINE(0, 28) +#define RSTMGR_QSPI RSTMGR_DEFINE(1, 5) +#define RSTMGR_SDMMC RSTMGR_DEFINE(1, 22) +#define RSTMGR_DMA RSTMGR_DEFINE(1, 28) #define RSTMGR_SDR RSTMGR_DEFINE(1, 29) /* Create a human-readable reference to SoCFPGA reset. */ -- 2.6.2

3 4

[U-Boot] [PATCH] usb: dwc3: Fix warnings on 64-bit builds
by Michal Simek 03 Nov '15

03 Nov '15

Change aritmentics to use 64bit types to be compatible with 64bit builds. Signed-off-by: Michal Simek <michal.simek(a)xilinx.com> --- drivers/usb/dwc3/core.c | 7 ++++--- drivers/usb/dwc3/ep0.c | 10 +++++----- drivers/usb/dwc3/gadget.c | 10 +++++----- drivers/usb/dwc3/io.h | 4 ++-- 4 files changed, 16 insertions(+), 15 deletions(-) diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index ab3c94e51275..0ae3de5c27b9 100644 --- a/drivers/usb/dwc3/core.c +++ b/drivers/usb/dwc3/core.c @@ -281,7 +281,7 @@ static int dwc3_setup_scratch_buffers(struct dwc3 *dwc) return 0; err1: - dma_unmap_single((void *)dwc->scratch_addr, dwc->nr_scratch * + dma_unmap_single((void *)(uintptr_t)dwc->scratch_addr, dwc->nr_scratch * DWC3_SCRATCHBUF_SIZE, DMA_BIDIRECTIONAL); err0: @@ -296,7 +296,7 @@ static void dwc3_free_scratch_buffers(struct dwc3 *dwc) if (!dwc->nr_scratch) return; - dma_unmap_single((void *)dwc->scratch_addr, dwc->nr_scratch * + dma_unmap_single((void *)(uintptr_t)dwc->scratch_addr, dwc->nr_scratch * DWC3_SCRATCHBUF_SIZE, DMA_BIDIRECTIONAL); kfree(dwc->scratchbuf); } @@ -629,7 +629,8 @@ int dwc3_uboot_init(struct dwc3_device *dwc3_dev) dwc = PTR_ALIGN(mem, DWC3_ALIGN_MASK + 1); dwc->mem = mem; - dwc->regs = (int *)(dwc3_dev->base + DWC3_GLOBALS_REGS_START); + dwc->regs = (void *)(uintptr_t)(dwc3_dev->base + + DWC3_GLOBALS_REGS_START); /* default to highest possible threshold */ lpm_nyet_threshold = 0xff; diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c index aba614fb4e98..12b133f93e17 100644 --- a/drivers/usb/dwc3/ep0.c +++ b/drivers/usb/dwc3/ep0.c @@ -81,8 +81,8 @@ static int dwc3_ep0_start_trans(struct dwc3 *dwc, u8 epnum, dma_addr_t buf_dma, trb->ctrl |= (DWC3_TRB_CTRL_IOC | DWC3_TRB_CTRL_LST); - dwc3_flush_cache((int)buf_dma, len); - dwc3_flush_cache((int)trb, sizeof(*trb)); + dwc3_flush_cache((long)buf_dma, len); + dwc3_flush_cache((long)trb, sizeof(*trb)); if (chain) return 0; @@ -790,7 +790,7 @@ static void dwc3_ep0_complete_data(struct dwc3 *dwc, if (!r) return; - dwc3_flush_cache((int)trb, sizeof(*trb)); + dwc3_flush_cache((long)trb, sizeof(*trb)); status = DWC3_TRB_SIZE_TRBSTS(trb->size); if (status == DWC3_TRBSTS_SETUP_PENDING) { @@ -821,7 +821,7 @@ static void dwc3_ep0_complete_data(struct dwc3 *dwc, ur->actual += transferred; trb++; - dwc3_flush_cache((int)trb, sizeof(*trb)); + dwc3_flush_cache((long)trb, sizeof(*trb)); length = trb->size & DWC3_TRB_SIZE_MASK; ep0->free_slot = 0; @@ -831,7 +831,7 @@ static void dwc3_ep0_complete_data(struct dwc3 *dwc, maxp); transferred = min_t(u32, ur->length - transferred, transfer_size - length); - dwc3_flush_cache((int)dwc->ep0_bounce, DWC3_EP0_BOUNCE_SIZE); + dwc3_flush_cache((long)dwc->ep0_bounce, DWC3_EP0_BOUNCE_SIZE); memcpy(buf, dwc->ep0_bounce, transferred); } else { transferred = ur->length - length; diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c index f3d649a5ee2f..8ff949d241f6 100644 --- a/drivers/usb/dwc3/gadget.c +++ b/drivers/usb/dwc3/gadget.c @@ -244,7 +244,7 @@ void dwc3_gadget_giveback(struct dwc3_ep *dep, struct dwc3_request *req, list_del(&req->list); req->trb = NULL; - dwc3_flush_cache((int)req->request.dma, req->request.length); + dwc3_flush_cache((long)req->request.dma, req->request.length); if (req->request.status == -EINPROGRESS) req->request.status = status; @@ -771,8 +771,8 @@ static void dwc3_prepare_one_trb(struct dwc3_ep *dep, trb->ctrl |= DWC3_TRB_CTRL_HWO; - dwc3_flush_cache((int)dma, length); - dwc3_flush_cache((int)trb, sizeof(*trb)); + dwc3_flush_cache((long)dma, length); + dwc3_flush_cache((long)trb, sizeof(*trb)); } /* @@ -1769,7 +1769,7 @@ static int dwc3_cleanup_done_reqs(struct dwc3 *dwc, struct dwc3_ep *dep, slot %= DWC3_TRB_NUM; trb = &dep->trb_pool[slot]; - dwc3_flush_cache((int)trb, sizeof(*trb)); + dwc3_flush_cache((long)trb, sizeof(*trb)); __dwc3_cleanup_done_trbs(dwc, dep, req, trb, event, status); dwc3_gadget_giveback(dep, req, status); @@ -2670,7 +2670,7 @@ void dwc3_gadget_uboot_handle_interrupt(struct dwc3 *dwc) for (i = 0; i < dwc->num_event_buffers; i++) { evt = dwc->ev_buffs[i]; - dwc3_flush_cache((int)evt->buf, evt->length); + dwc3_flush_cache((long)evt->buf, evt->length); } dwc3_thread_interrupt(0, dwc); diff --git a/drivers/usb/dwc3/io.h b/drivers/usb/dwc3/io.h index 5042a2419369..0d9fa220e922 100644 --- a/drivers/usb/dwc3/io.h +++ b/drivers/usb/dwc3/io.h @@ -23,7 +23,7 @@ #define CACHELINE_SIZE CONFIG_SYS_CACHELINE_SIZE static inline u32 dwc3_readl(void __iomem *base, u32 offset) { - u32 offs = offset - DWC3_GLOBALS_REGS_START; + unsigned long offs = offset - DWC3_GLOBALS_REGS_START; u32 value; /* @@ -38,7 +38,7 @@ static inline u32 dwc3_readl(void __iomem *base, u32 offset) static inline void dwc3_writel(void __iomem *base, u32 offset, u32 value) { - u32 offs = offset - DWC3_GLOBALS_REGS_START; + unsigned long offs = offset - DWC3_GLOBALS_REGS_START; /* * We requested the mem region starting from the Globals address -- 2.5.0

3 6