December 2014 - U-Boot

[U-Boot] [PATCH] powerpc/mpc85xx: use correct dma compatible for several SoCs
by Laurentiu Tudor 05 Dec '14

05 Dec '14

Newer qoriq socs have an updated dma ip block with a different compatible. Let's make sure we use the proper string so that the dmas get their liodn. In order to have the means to specify the compatible string, the liodn setting macros were updated to receive a new parameter for it. The following SoCs were changed to use the new compatible: T1023/4, T1040, T2080/1, T4240, B4860. Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor(a)freescale.com> --- depends on https://patchwork.ozlabs.org/patch/403532/ arch/powerpc/cpu/mpc85xx/b4860_ids.c | 4 ++-- arch/powerpc/cpu/mpc85xx/p2041_ids.c | 4 ++-- arch/powerpc/cpu/mpc85xx/p3041_ids.c | 4 ++-- arch/powerpc/cpu/mpc85xx/p4080_ids.c | 4 ++-- arch/powerpc/cpu/mpc85xx/p5020_ids.c | 4 ++-- arch/powerpc/cpu/mpc85xx/p5040_ids.c | 4 ++-- arch/powerpc/cpu/mpc85xx/t1024_ids.c | 4 ++-- arch/powerpc/cpu/mpc85xx/t1040_ids.c | 4 ++-- arch/powerpc/cpu/mpc85xx/t2080_ids.c | 6 +++--- arch/powerpc/cpu/mpc85xx/t4240_ids.c | 4 ++-- arch/powerpc/include/asm/fsl_liodn.h | 4 ++-- 11 files changed, 23 insertions(+), 23 deletions(-) diff --git a/arch/powerpc/cpu/mpc85xx/b4860_ids.c b/arch/powerpc/cpu/mpc85xx/b4860_ids.c index 1a30f1c..598f7bd 100644 --- a/arch/powerpc/cpu/mpc85xx/b4860_ids.c +++ b/arch/powerpc/cpu/mpc85xx/b4860_ids.c @@ -59,8 +59,8 @@ struct liodn_id_table liodn_tbl[] = { SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 1, 148), - SET_DMA_LIODN(1, 147), - SET_DMA_LIODN(2, 227), + SET_DMA_LIODN(1, "fsl,elo3-dma", 147), + SET_DMA_LIODN(2, "fsl,elo3-dma", 227), #ifndef CONFIG_PPC_B4420 SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0), diff --git a/arch/powerpc/cpu/mpc85xx/p2041_ids.c b/arch/powerpc/cpu/mpc85xx/p2041_ids.c index 488e078..6e3cddd 100644 --- a/arch/powerpc/cpu/mpc85xx/p2041_ids.c +++ b/arch/powerpc/cpu/mpc85xx/p2041_ids.c @@ -50,8 +50,8 @@ struct liodn_id_table liodn_tbl[] = { SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 194), SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 195), - SET_DMA_LIODN(1, 197), - SET_DMA_LIODN(2, 198), + SET_DMA_LIODN(1, "fsl,eloplus-dma", 197), + SET_DMA_LIODN(2, "fsl,eloplus-dma", 198), SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0), SET_GUTS_LIODN(NULL, 200, rio2liodnr, 0), diff --git a/arch/powerpc/cpu/mpc85xx/p3041_ids.c b/arch/powerpc/cpu/mpc85xx/p3041_ids.c index 7d98870..2b57703 100644 --- a/arch/powerpc/cpu/mpc85xx/p3041_ids.c +++ b/arch/powerpc/cpu/mpc85xx/p3041_ids.c @@ -51,8 +51,8 @@ struct liodn_id_table liodn_tbl[] = { SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 195), SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 196), - SET_DMA_LIODN(1, 197), - SET_DMA_LIODN(2, 198), + SET_DMA_LIODN(1, "fsl,eloplus-dma", 197), + SET_DMA_LIODN(2, "fsl,eloplus-dma", 198), SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0), SET_GUTS_LIODN(NULL, 200, rio2liodnr, 0), diff --git a/arch/powerpc/cpu/mpc85xx/p4080_ids.c b/arch/powerpc/cpu/mpc85xx/p4080_ids.c index b2a23c0..94a5143 100644 --- a/arch/powerpc/cpu/mpc85xx/p4080_ids.c +++ b/arch/powerpc/cpu/mpc85xx/p4080_ids.c @@ -40,8 +40,8 @@ struct liodn_id_table liodn_tbl[] = { SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 194), SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 195), - SET_DMA_LIODN(1, 196), - SET_DMA_LIODN(2, 197), + SET_DMA_LIODN(1, "fsl,eloplus-dma", 196), + SET_DMA_LIODN(2, "fsl,eloplus-dma", 197), SET_GUTS_LIODN("fsl,srio-rmu", 200, rmuliodnr, 0xd3000), diff --git a/arch/powerpc/cpu/mpc85xx/p5020_ids.c b/arch/powerpc/cpu/mpc85xx/p5020_ids.c index b5d787c..0f292cf 100644 --- a/arch/powerpc/cpu/mpc85xx/p5020_ids.c +++ b/arch/powerpc/cpu/mpc85xx/p5020_ids.c @@ -51,8 +51,8 @@ struct liodn_id_table liodn_tbl[] = { SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 195), SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 196), - SET_DMA_LIODN(1, 197), - SET_DMA_LIODN(2, 198), + SET_DMA_LIODN(1, "fsl,eloplus-dma", 197), + SET_DMA_LIODN(2, "fsl,eloplus-dma", 198), SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0), SET_GUTS_LIODN(NULL, 200, rio2liodnr, 0), diff --git a/arch/powerpc/cpu/mpc85xx/p5040_ids.c b/arch/powerpc/cpu/mpc85xx/p5040_ids.c index 990f179..d4343ef 100644 --- a/arch/powerpc/cpu/mpc85xx/p5040_ids.c +++ b/arch/powerpc/cpu/mpc85xx/p5040_ids.c @@ -42,8 +42,8 @@ struct liodn_id_table liodn_tbl[] = { SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 196), SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 197), - SET_DMA_LIODN(1, 193), - SET_DMA_LIODN(2, 194), + SET_DMA_LIODN(1, "fsl,eloplus-dma", 193), + SET_DMA_LIODN(2, "fsl,eloplus-dma", 194), }; int liodn_tbl_sz = ARRAY_SIZE(liodn_tbl); diff --git a/arch/powerpc/cpu/mpc85xx/t1024_ids.c b/arch/powerpc/cpu/mpc85xx/t1024_ids.c index 5f24c15..132689b 100644 --- a/arch/powerpc/cpu/mpc85xx/t1024_ids.c +++ b/arch/powerpc/cpu/mpc85xx/t1024_ids.c @@ -41,8 +41,8 @@ struct liodn_id_table liodn_tbl[] = { SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 228), SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 308), - SET_DMA_LIODN(1, 147), - SET_DMA_LIODN(2, 227), + SET_DMA_LIODN(1, "fsl,elo3-dma", 147), + SET_DMA_LIODN(2, "fsl,elo3-dma", 227), /* SET_NEXUS_LIODN(557), -- not yet implemented */ SET_QE_LIODN(559), SET_TDM_LIODN(560), diff --git a/arch/powerpc/cpu/mpc85xx/t1040_ids.c b/arch/powerpc/cpu/mpc85xx/t1040_ids.c index a5dfb81..268f829 100644 --- a/arch/powerpc/cpu/mpc85xx/t1040_ids.c +++ b/arch/powerpc/cpu/mpc85xx/t1040_ids.c @@ -42,8 +42,8 @@ struct liodn_id_table liodn_tbl[] = { SET_PCI_LIODN("fsl,qoriq-pcie-v2.2", 1, 148), - SET_DMA_LIODN(1, 147), - SET_DMA_LIODN(2, 227), + SET_DMA_LIODN(1, "fsl,elo3-dma", 147), + SET_DMA_LIODN(2, "fsl,elo3-dma", 227), /* SET_NEXUS_LIODN(557), -- not yet implemented */ SET_QE_LIODN(559), diff --git a/arch/powerpc/cpu/mpc85xx/t2080_ids.c b/arch/powerpc/cpu/mpc85xx/t2080_ids.c index 0bfd447..eda7f59 100644 --- a/arch/powerpc/cpu/mpc85xx/t2080_ids.c +++ b/arch/powerpc/cpu/mpc85xx/t2080_ids.c @@ -63,9 +63,9 @@ struct liodn_id_table liodn_tbl[] = { SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 308), SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 388), - SET_DMA_LIODN(1, 147), - SET_DMA_LIODN(2, 227), - SET_DMA_LIODN(3, 226), + SET_DMA_LIODN(1, "fsl,elo3-dma", 147), + SET_DMA_LIODN(2, "fsl,elo3-dma", 227), + SET_DMA_LIODN(3, "fsl,elo3-dma", 226), SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0), SET_GUTS_LIODN(NULL, 200, rio2liodnr, 0), diff --git a/arch/powerpc/cpu/mpc85xx/t4240_ids.c b/arch/powerpc/cpu/mpc85xx/t4240_ids.c index 1a3cb33..470b080 100644 --- a/arch/powerpc/cpu/mpc85xx/t4240_ids.c +++ b/arch/powerpc/cpu/mpc85xx/t4240_ids.c @@ -93,8 +93,8 @@ struct liodn_id_table liodn_tbl[] = { SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 308), SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 388), - SET_DMA_LIODN(1, 147), - SET_DMA_LIODN(2, 227), + SET_DMA_LIODN(1, "fsl,elo3-dma", 147), + SET_DMA_LIODN(2, "fsl,elo3-dma", 227), SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0), SET_GUTS_LIODN(NULL, 200, rio2liodnr, 0), diff --git a/arch/powerpc/include/asm/fsl_liodn.h b/arch/powerpc/include/asm/fsl_liodn.h index adfbb66..811f034 100644 --- a/arch/powerpc/include/asm/fsl_liodn.h +++ b/arch/powerpc/include/asm/fsl_liodn.h @@ -91,8 +91,8 @@ extern void fdt_fixup_liodn(void *blob); CONFIG_SYS_MPC85xx_PCIE##pciNum##_OFFSET) /* reg nodes for DMA start @ 0x300 */ -#define SET_DMA_LIODN(dmaNum, liodn) \ - SET_GUTS_LIODN("fsl,eloplus-dma", liodn, dma##dmaNum##liodnr,\ +#define SET_DMA_LIODN(dmaNum, compat, liodn) \ + SET_GUTS_LIODN(compat, liodn, dma##dmaNum##liodnr,\ CONFIG_SYS_MPC85xx_DMA##dmaNum##_OFFSET + 0x300) #define SET_SDHC_LIODN(sdhcNum, liodn) \ -- 1.8.3.1

2 1

[U-Boot] [PATCH] powerpc/mpc85xx: Update LIODN entries for T1040
by Priyanka Jain 05 Dec '14

05 Dec '14

Signed-off-by: Priyanka Jain <Priyanka.Jain(a)freescale.com> --- arch/powerpc/cpu/mpc85xx/t1040_ids.c | 26 +++++++++++++++++++------- 1 files changed, 19 insertions(+), 7 deletions(-) diff --git a/arch/powerpc/cpu/mpc85xx/t1040_ids.c b/arch/powerpc/cpu/mpc85xx/t1040_ids.c index a5dfb81..2903d57 100644 --- a/arch/powerpc/cpu/mpc85xx/t1040_ids.c +++ b/arch/powerpc/cpu/mpc85xx/t1040_ids.c @@ -24,12 +24,6 @@ struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = { }; #endif -struct srio_liodn_id_table srio_liodn_tbl[] = { - SET_SRIO_LIODN_1(1, 307), - SET_SRIO_LIODN_1(2, 387), -}; -int srio_liodn_tbl_sz = ARRAY_SIZE(srio_liodn_tbl); - struct liodn_id_table liodn_tbl[] = { #ifdef CONFIG_SYS_DPAA_QBMAN SET_QMAN_LIODN(62), @@ -38,9 +32,18 @@ struct liodn_id_table liodn_tbl[] = { SET_SDHC_LIODN(1, 552), + SET_PME_LIODN(117), + SET_USB_LIODN(1, "fsl-usb2-mph", 553), + SET_USB_LIODN(2, "fsl-usb2-dr", 554), - SET_PCI_LIODN("fsl,qoriq-pcie-v2.2", 1, 148), + SET_SATA_LIODN(1, 555), + SET_SATA_LIODN(2, 556), + + SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 1, 148), + SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 228), + SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 308), + SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 388), SET_DMA_LIODN(1, 147), SET_DMA_LIODN(2, 227), @@ -74,6 +77,12 @@ struct liodn_id_table sec_liodn_tbl[] = { SET_SEC_RTIC_LIODN_ENTRY(d, 551), SET_SEC_DECO_LIODN_ENTRY(0, 541, 610), SET_SEC_DECO_LIODN_ENTRY(1, 542, 611), + SET_SEC_DECO_LIODN_ENTRY(2, 543, 612), + SET_SEC_DECO_LIODN_ENTRY(3, 544, 613), + SET_SEC_DECO_LIODN_ENTRY(4, 545, 614), + SET_SEC_DECO_LIODN_ENTRY(5, 546, 615), + SET_SEC_DECO_LIODN_ENTRY(6, 547, 616), + SET_SEC_DECO_LIODN_ENTRY(7, 548, 617), }; int sec_liodn_tbl_sz = ARRAY_SIZE(sec_liodn_tbl); @@ -82,4 +91,7 @@ struct liodn_id_table liodn_bases[] = { #ifdef CONFIG_SYS_DPAA_FMAN [FSL_HW_PORTAL_FMAN1] = SET_LIODN_BASE_1(973), #endif +#ifdef CONFIG_SYS_DPAA_PME + [FSL_HW_PORTAL_PME] = SET_LIODN_BASE_2(770, 846), +#endif }; -- 1.7.4.1

2 1

[U-Boot] [PATCH v2] powerpc/t2080: updating rcw for silicon v1.1
by Shengzhou Liu 05 Dec '14

05 Dec '14

T2080 v1.1 requires different MEM_PLL_RAT from previous v1.0, and also update core frequency to 1.8GHz for v1.1. We reserve the support for T2080 v1.0 and enable v1.1 by default. Signed-off-by: Shengzhou Liu <Shengzhou.Liu(a)freescale.com> --- v2: reserve v1.0 support. board/freescale/t208xqds/t2080_rcw.cfg | 16 ++++++++++++---- board/freescale/t208xrdb/t2080_rcw.cfg | 20 ++++++++++++++------ 2 files changed, 26 insertions(+), 10 deletions(-) diff --git a/board/freescale/t208xqds/t2080_rcw.cfg b/board/freescale/t208xqds/t2080_rcw.cfg index 972dedc..52a1652 100644 --- a/board/freescale/t208xqds/t2080_rcw.cfg +++ b/board/freescale/t208xqds/t2080_rcw.cfg @@ -1,8 +1,16 @@ #PBL preamble and RCW header aa55aa55 010e0100 -#SerDes Protocol: 0x66_0x16 -#Core/DDR: 1533Mhz/2133MT/s -12100017 15000000 00000000 00000000 -66150002 00008400 e8104000 c1000000 + +#For T2080 v1.0 +#SerDes=0x66_0x16, Core=1533MHz, DDR=2133MT/s +#12100017 15000000 00000000 00000000 +#66150002 00008400 e8104000 c1000000 +#00000000 00000000 00000000 000307fc +#00000000 00000000 00000000 00000004 + +#For T2080 v1.1 +#SerDes=0x66_0x15, Core=1800MHz, DDR=1867MT/s +0c070012 0e000000 00000000 00000000 +66150002 00000000 e8104000 c1000000 00000000 00000000 00000000 000307fc 00000000 00000000 00000000 00000004 diff --git a/board/freescale/t208xrdb/t2080_rcw.cfg b/board/freescale/t208xrdb/t2080_rcw.cfg index 15e1bf4..59025ea 100644 --- a/board/freescale/t208xrdb/t2080_rcw.cfg +++ b/board/freescale/t208xrdb/t2080_rcw.cfg @@ -1,8 +1,16 @@ -#PBL preamble and RCW header for T2080RDB +#PBL preamble and RCW header aa55aa55 010e0100 -#SerDes Protocol: 0x66_0x16 -#Core/DDR: 1533Mhz/1600MT/s -120c0017 15000000 00000000 00000000 -66150002 00008400 ec104000 c1000000 -00000000 00000000 00000000 000307fc + +#For T2080 v1.0 +#SerDes=0x66_0x16, Core=1533MHz, DDR=1600MT/s +#120c0017 15000000 00000000 00000000 +#66150002 00008400 ec104000 c1000000 +#00000000 00000000 00000000 000307fc +#00000000 00000000 00000000 00000004 + +#For T2080 v1.1 +#SerDes=0x66_0x15, Core:1800MHz, DDR:1600MT/s +1206001b 15000000 00000000 00000000 +66150002 00000000 e8104000 c1000000 +00800000 00000000 00000000 000307fc 00000000 00000000 00000000 00000004 -- 1.8.0

2 1

[U-Boot] [PATCH 5/5] B4860QDS: Enable enet port as per fsl_b4860_serdes2 string in hwconfig
by shh.xie＠gmail.com 05 Dec '14

05 Dec '14

From: Suresh Gupta <suresh.gupta(a)freescale.com> In B4860QDS board SerDes2 lanes EFGH either go to SFP or AMC riser card slot2 so either DTSEC3/DTSEC4 or TGEC1/TGEC2 should be accessible. This Patch enables DTSEC3/DTSEC4 or TGEC1/TGEC2 on bases of user specified string fsl_b4860_serdes2:sfp_amc=amc or fsl_b4860_serdes2:sfp_amc=sfp respectively in hwconfig. Signed-off-by: Suresh Gupta <suresh.gupta(a)freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie(a)freescale.com> --- board/freescale/b4860qds/eth_b4860qds.c | 19 ++++++++++ drivers/net/fm/b4860.c | 64 +++++++++++++++++++++++++++++++-- 2 files changed, 81 insertions(+), 2 deletions(-) diff --git a/board/freescale/b4860qds/eth_b4860qds.c b/board/freescale/b4860qds/eth_b4860qds.c index 595bb4c..501d4b3 100644 --- a/board/freescale/b4860qds/eth_b4860qds.c +++ b/board/freescale/b4860qds/eth_b4860qds.c @@ -407,6 +407,25 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, fdt_setprop(fdt, offset, "fixed-link", &f_link, sizeof(f_link)); break; + case 0x98: /* XAUI interface */ + sprintf(alias, "phy_xaui_slot1"); + fdt_status_okay_by_alias(fdt, alias); + + sprintf(alias, "phy_xaui_slot2"); + fdt_status_okay_by_alias(fdt, alias); + break; + case 0x9e: /* XAUI interface */ + case 0x9a: + case 0x93: + case 0x91: + sprintf(alias, "phy_xaui_slot1"); + fdt_status_okay_by_alias(fdt, alias); + break; + case 0x97: /* XAUI interface */ + case 0xc3: + sprintf(alias, "phy_xaui_slot2"); + fdt_status_okay_by_alias(fdt, alias); + break; default: break; } diff --git a/drivers/net/fm/b4860.c b/drivers/net/fm/b4860.c index 71285a8..eb058c9 100644 --- a/drivers/net/fm/b4860.c +++ b/drivers/net/fm/b4860.c @@ -10,6 +10,7 @@ #include <asm/io.h> #include <asm/immap_85xx.h> #include <asm/fsl_serdes.h> +#include <hwconfig.h> u32 port_to_devdisr[] = { [FM1_DTSEC1] = FSL_CORENET_DEVDISR2_DTSEC1_1, @@ -46,17 +47,76 @@ void fman_enable_port(enum fm_port port) phy_interface_t fman_port_enet_if(enum fm_port port) { +#if defined(CONFIG_B4860QDS) + u32 serdes2_prtcl; + char buffer[HWCONFIG_BUFFER_SIZE]; + char *buf = NULL; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); +#endif + if (is_device_disabled(port)) return PHY_INTERFACE_MODE_NONE; /*B4860 has two 10Gig Mac*/ if ((port == FM1_10GEC1 || port == FM1_10GEC2) && ((is_serdes_configured(XAUI_FM1_MAC9)) || - (is_serdes_configured(XAUI_FM1_MAC10)) || + #if !defined(CONFIG_B4860QDS) (is_serdes_configured(XFI_FM1_MAC9)) || - (is_serdes_configured(XFI_FM1_MAC10)))) + (is_serdes_configured(XFI_FM1_MAC10)) || + #endif + (is_serdes_configured(XAUI_FM1_MAC10)) + )) return PHY_INTERFACE_MODE_XGMII; +#if defined(CONFIG_B4860QDS) + serdes2_prtcl = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS2_PRTCL; + + if (serdes2_prtcl) { + serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; + switch (serdes2_prtcl) { + case 0x80: + case 0x81: + case 0x82: + case 0x83: + case 0x84: + case 0x85: + case 0x86: + case 0x87: + case 0x88: + case 0x89: + case 0x8a: + case 0x8b: + case 0x8c: + case 0x8d: + case 0x8e: + case 0xb1: + case 0xb2: + /* + * Extract hwconfig from environment since environment + * is not setup yet + */ + getenv_f("hwconfig", buffer, sizeof(buffer)); + buf = buffer; + + /* check if XFI interface enable in hwconfig for 10g */ + if (hwconfig_subarg_cmp_f("fsl_b4860_serdes2", + "sfp_amc", "sfp", buf)) { + if ((port == FM1_10GEC1 || + port == FM1_10GEC2) && + ((is_serdes_configured(XFI_FM1_MAC9)) || + (is_serdes_configured(XFI_FM1_MAC10)))) + return PHY_INTERFACE_MODE_XGMII; + else if ((port == FM1_DTSEC1) || + (port == FM1_DTSEC2) || + (port == FM1_DTSEC3) || + (port == FM1_DTSEC4)) + return PHY_INTERFACE_MODE_NONE; + } + } + } +#endif + /* Fix me need to handle RGMII here first */ switch (port) { -- 2.1.0.27.g96db324

2 1

[U-Boot] [PATCH 4/5] powerpc/b4860qds: add workaround for XFI
by shh.xie＠gmail.com 05 Dec '14

05 Dec '14

From: Shaohui Xie <Shaohui.Xie(a)freescale.com> XFI does not work stable on current board, it's due to heat sink issue, to make it work stable the board needs additional heat sink, enable two XFI lanes only. Right now we do not have such an erratum for the issue, so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it. The workaround will only be used in XFI protocols and only if the hwconfig indicates that XFI is prefered. A new VSC3308 config function is used instead of re-use the original function, to avoid making the function complex and ugly. Signed-off-by: Shaohui Xie <Shaohui.Xie(a)freescale.com> --- arch/powerpc/cpu/mpc85xx/cmd_errata.c | 3 + board/freescale/b4860qds/b4860qds.c | 13 ++++ board/freescale/common/vsc3316_3308.c | 108 ++++++++++++++++++++++++++++++++++ board/freescale/common/vsc3316_3308.h | 4 ++ include/configs/B4860QDS.h | 2 + 5 files changed, 130 insertions(+) diff --git a/arch/powerpc/cpu/mpc85xx/cmd_errata.c b/arch/powerpc/cpu/mpc85xx/cmd_errata.c index 3a04a89..6de867f 100644 --- a/arch/powerpc/cpu/mpc85xx/cmd_errata.c +++ b/arch/powerpc/cpu/mpc85xx/cmd_errata.c @@ -308,6 +308,9 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) #ifdef CONFIG_SYS_FSL_ERRATUM_A005434 puts("Work-around for Erratum A-005434 enabled\n"); #endif +#if defined(CONFIG_SYS_FSL_B4860QDS_XFI_ERR) && defined(CONFIG_B4860QDS) + puts("Work-around for Erratum XFI on B4860QDS enabled\n"); +#endif return 0; } diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c index 86c7c66..1006d2e 100644 --- a/board/freescale/b4860qds/b4860qds.c +++ b/board/freescale/b4860qds/b4860qds.c @@ -548,6 +548,18 @@ int configure_vsc3316_3308(void) if (hwconfig_subarg_cmp_f("fsl_b4860_serdes2", "sfp_amc", "sfp", buf)) { +#ifdef CONFIG_SYS_FSL_B4860QDS_XFI_ERR + /* change default VSC3308 for XFI erratum */ + ret = vsc3308_config_adjust(VSC3308_TX_ADDRESS, + vsc08_tx_sfp, num_vsc08_con); + if (ret) + return ret; + + ret = vsc3308_config_adjust(VSC3308_RX_ADDRESS, + vsc08_rx_sfp, num_vsc08_con); + if (ret) + return ret; +#else ret = vsc3308_config(VSC3308_TX_ADDRESS, vsc08_tx_sfp, num_vsc08_con); if (ret) @@ -557,6 +569,7 @@ int configure_vsc3316_3308(void) vsc08_rx_sfp, num_vsc08_con); if (ret) return ret; +#endif } else { ret = vsc3308_config(VSC3308_TX_ADDRESS, vsc08_tx_amc, num_vsc08_con); diff --git a/board/freescale/common/vsc3316_3308.c b/board/freescale/common/vsc3316_3308.c index 97a25e8..dd9c37e 100644 --- a/board/freescale/common/vsc3316_3308.c +++ b/board/freescale/common/vsc3316_3308.c @@ -13,7 +13,12 @@ #define INPUT_STATE_REG 0x13 #define GLOBAL_INPUT_ISE1 0x51 #define GLOBAL_INPUT_ISE2 0x52 +#define GLOBAL_INPUT_GAIN 0x53 #define GLOBAL_INPUT_LOS 0x55 +#define GLOBAL_OUTPUT_PE1 0x56 +#define GLOBAL_OUTPUT_PE2 0x57 +#define GLOBAL_OUTPUT_LEVEL 0x58 +#define GLOBAL_OUTPUT_TERMINATION 0x5A #define GLOBAL_CORE_CNTRL 0x5D #define OUTPUT_MODE_PAGE 0x23 #define CORE_CONTROL_PAGE 0x25 @@ -92,6 +97,109 @@ int vsc3316_config(unsigned int vsc_addr, int8_t con_arr[][2], return 0; } +#ifdef CONFIG_SYS_FSL_B4860QDS_XFI_ERR +int vsc3308_config_adjust(unsigned int vsc_addr, const int8_t con_arr[][2], + unsigned int num_con) +{ + unsigned int i; + u8 rev_id = 0; + int ret; + + debug("VSC:Initializing VSC3308 at I2C address 0x%x for Tx\n", + vsc_addr); + + ret = i2c_read(vsc_addr, REVISION_ID_REG, 1, &rev_id, 1); + if (ret < 0) { + printf("VSC:0x%x could not read REV_ID from device.\n", + vsc_addr); + return ret; + } + + if (rev_id != 0xab) { + printf("VSC: device at address 0x%x is not VSC3316/3308.\n", + vsc_addr); + return -ENODEV; + } + + ret = vsc_if_enable(vsc_addr); + if (ret) { + printf("VSC:0x%x could not configured for 2-wire I/F.\n", + vsc_addr); + return ret; + } + + /* config connections - page 0x00 */ + i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE); + + /* Configure Global Input ISE */ + i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE1, 0); + i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE2, 0); + + /* Configure Tx/Rx Global Output PE1 */ + i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_PE1, 0); + + /* Configure Tx/Rx Global Output PE2 */ + i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_PE2, 0); + + /* Configure Tx/Rx Global Input GAIN */ + i2c_reg_write(vsc_addr, GLOBAL_INPUT_GAIN, 0x3F); + + /* Setting Global Input LOS threshold value */ + i2c_reg_write(vsc_addr, GLOBAL_INPUT_LOS, 0xE0); + + /* Setting Global output termination */ + i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_TERMINATION, 0); + + /* Configure Tx/Rx Global Output level */ + if (vsc_addr == VSC3308_TX_ADDRESS) + i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_LEVEL, 4); + else + i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_LEVEL, 2); + + /* Making crosspoint connections, by connecting required + * input to output */ + for (i = 0; i < num_con ; i++) + i2c_reg_write(vsc_addr, con_arr[i][1], con_arr[i][0]); + + /* input state - page 0x13 */ + i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, INPUT_STATE_REG); + /* Turning off all the required input of the switch */ + for (i = 0; i < num_con; i++) + i2c_reg_write(vsc_addr, con_arr[i][0], 1); + + /* only turn on specific Tx/Rx requested by the XFI erratum */ + if (vsc_addr == VSC3308_TX_ADDRESS) { + i2c_reg_write(vsc_addr, 2, 0); + i2c_reg_write(vsc_addr, 3, 0); + } else { + i2c_reg_write(vsc_addr, 0, 0); + i2c_reg_write(vsc_addr, 1, 0); + } + + /* config output mode - page 0x23 */ + i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE); + /* Turn off the Output driver correspond to required output*/ + for (i = 0; i < num_con ; i++) + i2c_reg_write(vsc_addr, con_arr[i][1], 1); + + /* only turn on specific Tx/Rx requested by the XFI erratum */ + if (vsc_addr == VSC3308_TX_ADDRESS) { + i2c_reg_write(vsc_addr, 0, 0); + i2c_reg_write(vsc_addr, 1, 0); + } else { + i2c_reg_write(vsc_addr, 3, 0); + i2c_reg_write(vsc_addr, 4, 0); + } + + /* configure global core control register, Turn on Global core power */ + i2c_reg_write(vsc_addr, GLOBAL_CORE_CNTRL, 0); + + vsc_wp_config(vsc_addr); + + return 0; +} +#endif + int vsc3308_config(unsigned int vsc_addr, const int8_t con_arr[][2], unsigned int num_con) { diff --git a/board/freescale/common/vsc3316_3308.h b/board/freescale/common/vsc3316_3308.h index 2a49187..d722ea3 100644 --- a/board/freescale/common/vsc3316_3308.h +++ b/board/freescale/common/vsc3316_3308.h @@ -14,6 +14,10 @@ int vsc_if_enable(unsigned int vsc_addr); int vsc3316_config(unsigned int vsc_addr, int8_t con_arr[][2], unsigned int num_con); +#ifdef CONFIG_SYS_FSL_B4860QDS_XFI_ERR +int vsc3308_config_adjust(unsigned int vsc_addr, const int8_t con_arr[][2], + unsigned int num_con); +#endif int vsc3308_config(unsigned int vsc_addr, const int8_t con_arr[][2], unsigned int num_con); void vsc_wp_config(unsigned int vsc_addr); diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h index f2b788a..78357a5 100644 --- a/include/configs/B4860QDS.h +++ b/include/configs/B4860QDS.h @@ -730,6 +730,8 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ #endif +#define CONFIG_SYS_FSL_B4860QDS_XFI_ERR + /* * Environment */ -- 2.1.0.27.g96db324

2 1

[U-Boot] [PATCH 3/5] B4860QDS: Enable SFP or AMC on basis of hwconfig string
by shh.xie＠gmail.com 05 Dec '14

05 Dec '14

From: Suresh Gupta <suresh.gupta(a)freescale.com> SerDes2 lanes EFGH either go to SFP or AMC riser card slot2. By default AMC will be configured even if no hwconfig is specified. To enable XFI via SFP use the below hwconfig: fsl_b4860_serdes2:sfp_amc=sfp Signed-off-by: Suresh Gupta <suresh.gupta(a)freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal(a)ffeescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie(a)freescale.com> --- board/freescale/b4860qds/b4860qds.c | 41 +++++++++++++++++++++++++++++-------- 1 file changed, 33 insertions(+), 8 deletions(-) diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c index 6a7e426..86c7c66 100644 --- a/board/freescale/b4860qds/b4860qds.c +++ b/board/freescale/b4860qds/b4860qds.c @@ -19,6 +19,7 @@ #include <asm/fsl_portals.h> #include <asm/fsl_liodn.h> #include <fm_eth.h> +#include <hwconfig.h> #include "../common/qixis.h" #include "../common/vsc3316_3308.h" @@ -333,6 +334,8 @@ int configure_vsc3316_3308(void) unsigned int num_vsc16_con, num_vsc08_con; u32 serdes1_prtcl, serdes2_prtcl; int ret; + char buffer[HWCONFIG_BUFFER_SIZE]; + char *buf = NULL; serdes1_prtcl = in_be32(&gur->rcwsr[4]) & FSL_CORENET2_RCWSR4_SRDS1_PRTCL; @@ -536,14 +539,36 @@ int configure_vsc3316_3308(void) case 0xb1: case 0xb2: if (!ret) { - ret = vsc3308_config(VSC3308_TX_ADDRESS, - vsc08_tx_sfp, num_vsc08_con); - if (ret) - return ret; - ret = vsc3308_config(VSC3308_RX_ADDRESS, - vsc08_rx_sfp, num_vsc08_con); - if (ret) - return ret; + /* + * Extract hwconfig from environment since environment + * is not setup properly yet + */ + getenv_f("hwconfig", buffer, sizeof(buffer)); + buf = buffer; + + if (hwconfig_subarg_cmp_f("fsl_b4860_serdes2", + "sfp_amc", "sfp", buf)) { + ret = vsc3308_config(VSC3308_TX_ADDRESS, + vsc08_tx_sfp, num_vsc08_con); + if (ret) + return ret; + + ret = vsc3308_config(VSC3308_RX_ADDRESS, + vsc08_rx_sfp, num_vsc08_con); + if (ret) + return ret; + } else { + ret = vsc3308_config(VSC3308_TX_ADDRESS, + vsc08_tx_amc, num_vsc08_con); + if (ret) + return ret; + + ret = vsc3308_config(VSC3308_RX_ADDRESS, + vsc08_rx_amc, num_vsc08_con); + if (ret) + return ret; + } + } else { return ret; } -- 2.1.0.27.g96db324

2 1

[U-Boot] [PATCH 2/5] powerpc/b4860qds: dtb fixup for xfi
by shh.xie＠gmail.com 05 Dec '14

05 Dec '14

From: Shaohui Xie <Shaohui.Xie(a)freescale.com> Since xfi has no phy, we delete the property "phy-handle" and use a "fixed-link" property for a xfi port. Signed-off-by: Shaohui Xie <Shaohui.Xie(a)freescale.com> --- board/freescale/b4860qds/eth_b4860qds.c | 38 +++++++++++++++++++++++++++++++++ 1 file changed, 38 insertions(+) diff --git a/board/freescale/b4860qds/eth_b4860qds.c b/board/freescale/b4860qds/eth_b4860qds.c index aa48b5e..595bb4c 100644 --- a/board/freescale/b4860qds/eth_b4860qds.c +++ b/board/freescale/b4860qds/eth_b4860qds.c @@ -365,6 +365,11 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, { int phy; char alias[32]; + struct fixed_link f_link; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 prtcl2 = in_be32(&gur->rcwsr[4]) & FSL_CORENET2_RCWSR4_SRDS2_PRTCL; + + prtcl2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) { phy = fm_info_get_phy_address(port); @@ -372,6 +377,39 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, sprintf(alias, "phy_sgmii_%x", phy); fdt_set_phy_handle(fdt, compat, addr, alias); fdt_status_okay_by_alias(fdt, alias); + } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) { + /* check if it's XFI interface for 10g */ + switch (prtcl2) { + case 0x80: + case 0x81: + case 0x82: + case 0x83: + case 0x84: + case 0x85: + case 0x86: + case 0x87: + case 0x88: + case 0x89: + case 0x8a: + case 0x8b: + case 0x8c: + case 0x8d: + case 0x8e: + case 0xb1: + case 0xb2: + f_link.phy_id = port; + f_link.duplex = 1; + f_link.link_speed = 10000; + f_link.pause = 0; + f_link.asym_pause = 0; + + fdt_delprop(fdt, offset, "phy-handle"); + fdt_setprop(fdt, offset, "fixed-link", &f_link, + sizeof(f_link)); + break; + default: + break; + } } } -- 2.1.0.27.g96db324

2 1

[U-Boot] [PATCH 1/5] powerpc/b4860qds: add xfi support
by shh.xie＠gmail.com 05 Dec '14

05 Dec '14

From: Shaohui Xie <Shaohui.Xie(a)freescale.com> We need following changes to make xfi work on B4: 1. set cross-point switch VSC3308 to use sfp config when running xfi; 2. add 10G interface check for xfi; 3. set phy address for xfi so the 10G ports can be registered by mdio; Signed-off-by: Shaohui Xie <Shaohui.Xie(a)freescale.com> --- board/freescale/b4860qds/b4860qds.c | 40 +++++++++++++++++++++++++++------ board/freescale/b4860qds/eth_b4860qds.c | 6 +++++ drivers/net/fm/b4860.c | 4 +++- 3 files changed, 42 insertions(+), 8 deletions(-) diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c index c819368..6a7e426 100644 --- a/board/freescale/b4860qds/b4860qds.c +++ b/board/freescale/b4860qds/b4860qds.c @@ -490,6 +490,9 @@ int configure_vsc3316_3308(void) return -1; } + num_vsc08_con = NUM_CON_VSC3308; + /* Configure VSC3308 crossbar switch */ + ret = select_i2c_ch_pca(I2C_CH_VSC3308); switch (serdes2_prtcl) { #ifdef CONFIG_PPC_B4420 case 0x9d: @@ -497,18 +500,11 @@ int configure_vsc3316_3308(void) case 0x9E: case 0x9A: case 0x98: - case 0xb1: - case 0xb2: case 0x48: case 0x49: case 0x4E: - case 0x8C: - case 0x8D: case 0x79: case 0x7A: - num_vsc08_con = NUM_CON_VSC3308; - /* Configure VSC3308 crossbar switch */ - ret = select_i2c_ch_pca(I2C_CH_VSC3308); if (!ret) { ret = vsc3308_config(VSC3308_TX_ADDRESS, vsc08_tx_amc, num_vsc08_con); @@ -522,6 +518,36 @@ int configure_vsc3316_3308(void) return ret; } break; + case 0x80: + case 0x81: + case 0x82: + case 0x83: + case 0x84: + case 0x85: + case 0x86: + case 0x87: + case 0x88: + case 0x89: + case 0x8a: + case 0x8b: + case 0x8c: + case 0x8d: + case 0x8e: + case 0xb1: + case 0xb2: + if (!ret) { + ret = vsc3308_config(VSC3308_TX_ADDRESS, + vsc08_tx_sfp, num_vsc08_con); + if (ret) + return ret; + ret = vsc3308_config(VSC3308_RX_ADDRESS, + vsc08_rx_sfp, num_vsc08_con); + if (ret) + return ret; + } else { + return ret; + } + break; default: printf("WARNING:VSC crossbars programming not supported for: %x" " SerDes2 Protocol.\n", serdes2_prtcl); diff --git a/board/freescale/b4860qds/eth_b4860qds.c b/board/freescale/b4860qds/eth_b4860qds.c index 2726cd2..aa48b5e 100644 --- a/board/freescale/b4860qds/eth_b4860qds.c +++ b/board/freescale/b4860qds/eth_b4860qds.c @@ -268,6 +268,12 @@ int board_eth_init(bd_t *bis) CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); fm_info_set_phy_address(FM1_DTSEC4, CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR); + /* + * XFI does not need a PHY to work, but to make U-boot + * happy, assign a fake PHY address for a XFI port. + */ + fm_info_set_phy_address(FM1_10GEC1, 0); + fm_info_set_phy_address(FM1_10GEC2, 1); break; case 0x98: /* XAUI in Slot1 and Slot2 */ diff --git a/drivers/net/fm/b4860.c b/drivers/net/fm/b4860.c index 373cc4f..71285a8 100644 --- a/drivers/net/fm/b4860.c +++ b/drivers/net/fm/b4860.c @@ -52,7 +52,9 @@ phy_interface_t fman_port_enet_if(enum fm_port port) /*B4860 has two 10Gig Mac*/ if ((port == FM1_10GEC1 || port == FM1_10GEC2) && ((is_serdes_configured(XAUI_FM1_MAC9)) || - (is_serdes_configured(XAUI_FM1_MAC10)))) + (is_serdes_configured(XAUI_FM1_MAC10)) || + (is_serdes_configured(XFI_FM1_MAC9)) || + (is_serdes_configured(XFI_FM1_MAC10)))) return PHY_INTERFACE_MODE_XGMII; /* Fix me need to handle RGMII here first */ -- 2.1.0.27.g96db324

3 2

[U-Boot] [PATCH 1/3] 85xx/b4860: Add alternate serdes protocols for B4860/B4420
by Shaveta Leekha 05 Dec '14

05 Dec '14

Addded Alternate options with LC VCO for following protocols: 0x02 --> 0x01 0x08 --> 0x07 0x18 --> 0x17 0x1E --> 0x1D 0x49 --> 0x48 0x6F --> 0x6E 0x9A --> 0x99 0x9E --> 0x9D Signed-off-by: Shaveta Leekha <shaveta(a)freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal(a)freescale.com> Change-Id: Iefe14012ee897095f0198453d50f31096ca020e2 Reviewed-on: http://git.am.freescale.net:8181/23352 Tested-by: Review Code-CDREVIEW <CDREVIEW(a)freescale.com> Reviewed-by: Yusong Sun <yorksun(a)freescale.com> --- arch/powerpc/cpu/mpc85xx/b4860_serdes.c | 19 +++++++++++++++++++ 1 files changed, 19 insertions(+), 0 deletions(-) diff --git a/arch/powerpc/cpu/mpc85xx/b4860_serdes.c b/arch/powerpc/cpu/mpc85xx/b4860_serdes.c index cf18be5..63172de 100644 --- a/arch/powerpc/cpu/mpc85xx/b4860_serdes.c +++ b/arch/powerpc/cpu/mpc85xx/b4860_serdes.c @@ -18,6 +18,8 @@ struct serdes_config { #ifdef CONFIG_PPC_B4860 static struct serdes_config serdes1_cfg_tbl[] = { /* SerDes 1 */ + {0x01, {AURORA, AURORA, CPRI6, CPRI5, + CPRI4, CPRI3, CPRI2, CPRI1} }, {0x02, {AURORA, AURORA, CPRI6, CPRI5, CPRI4, CPRI3, CPRI2, CPRI1} }, {0x04, {AURORA, AURORA, CPRI6, CPRI5, @@ -26,6 +28,8 @@ static struct serdes_config serdes1_cfg_tbl[] = { CPRI4, CPRI3, CPRI2, CPRI1} }, {0x06, {AURORA, AURORA, CPRI6, CPRI5, CPRI4, CPRI3, CPRI2, CPRI1} }, + {0x07, {AURORA, AURORA, CPRI6, CPRI5, + CPRI4, CPRI3, CPRI2, CPRI1} }, {0x08, {AURORA, AURORA, CPRI6, CPRI5, CPRI4, CPRI3, CPRI2, CPRI1} }, {0x09, {AURORA, AURORA, CPRI6, CPRI5, @@ -184,12 +188,17 @@ static struct serdes_config serdes1_cfg_tbl[] = { CPRI4, CPRI3, NONE, NONE} }, {0x0F, {NONE, NONE, CPRI6, CPRI5, CPRI4, CPRI3, NONE, NONE} }, + {0x17, {NONE, NONE, + SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, + NONE, NONE, NONE, NONE} }, {0x18, {NONE, NONE, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, NONE, NONE, NONE, NONE} }, {0x1B, {NONE, NONE, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, NONE, NONE, NONE, NONE} }, + {0x1D, {NONE, NONE, AURORA, AURORA, + NONE, NONE, NONE, NONE} }, {0x1E, {NONE, NONE, AURORA, AURORA, NONE, NONE, NONE, NONE} }, {0x21, {NONE, NONE, AURORA, AURORA, @@ -199,19 +208,29 @@ static struct serdes_config serdes1_cfg_tbl[] = { {} }; static struct serdes_config serdes2_cfg_tbl[] = { + {0x48, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + SGMII_FM1_DTSEC3, AURORA, + NONE, NONE, NONE, NONE} }, {0x49, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC3, AURORA, NONE, NONE, NONE, NONE} }, {0x4A, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC3, AURORA, NONE, NONE, NONE, NONE} }, + {0x6E, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + AURORA, AURORA, NONE, NONE, NONE, NONE} }, {0x6F, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, AURORA, AURORA, NONE, NONE, NONE, NONE} }, {0x70, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, AURORA, AURORA, NONE, NONE, NONE, NONE} }, + {0x99, {PCIE1, PCIE1, + SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, + NONE, NONE, NONE, NONE} }, {0x9A, {PCIE1, PCIE1, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, NONE, NONE, NONE, NONE} }, + {0x9D, {PCIE1, PCIE1, PCIE1, PCIE1, + NONE, NONE, NONE, NONE} }, {0x9E, {PCIE1, PCIE1, PCIE1, PCIE1, NONE, NONE, NONE, NONE} }, {} -- 1.7.6.GIT

2 2

[U-Boot] [PATCH 3/3] B4860: Add alternate LC VCO serdes protocols support in board file
by Shaveta Leekha 05 Dec '14

05 Dec '14

Add the support of newly added LC VCO SerDes protocols for configuration of IDT and VSC crossbar Signed-off-by: Shaveta Leekha <shaveta(a)freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal(a)freescale.com> Change-Id: I16ad23e2cbea3b0a232a153984d5126bc79ddd26 Reviewed-on: http://git.am.freescale.net:8181/23354 Tested-by: Yusong Sun <yorksun(a)freescale.com> Reviewed-by: Yusong Sun <yorksun(a)freescale.com> --- board/freescale/b4860qds/b4860qds.c | 13 +++++++++++++ 1 files changed, 13 insertions(+), 0 deletions(-) diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c index 975952f..7f2437e 100644 --- a/board/freescale/b4860qds/b4860qds.c +++ b/board/freescale/b4860qds/b4860qds.c @@ -385,15 +385,18 @@ int configure_vsc3316_3308(void) } break; + case 0x01: case 0x02: case 0x04: case 0x05: case 0x06: + case 0x07: case 0x08: case 0x09: case 0x0A: case 0x0B: case 0x0C: + case 0x2F: case 0x30: case 0x32: case 0x33: @@ -494,10 +497,14 @@ int configure_vsc3316_3308(void) case 0x9E: case 0x9A: case 0x98: + case 0xb1: case 0xb2: + case 0x48: case 0x49: case 0x4E: + case 0x8C: case 0x8D: + case 0x79: case 0x7A: num_vsc08_con = NUM_CON_VSC3308; /* Configure VSC3308 crossbar switch */ @@ -730,19 +737,23 @@ int config_serdes1_refclks(void) * to 122.88MHz */ switch (serdes1_prtcl) { + case 0x29: case 0x2A: case 0x2C: case 0x2D: case 0x2E: + case 0x01: case 0x02: case 0x04: case 0x05: case 0x06: + case 0x07: case 0x08: case 0x09: case 0x0A: case 0x0B: case 0x0C: + case 0x2F: case 0x30: case 0x32: case 0x33: @@ -860,6 +871,8 @@ int config_serdes2_refclks(void) #endif case 0x9E: case 0x9A: + /* fallthrough */ + case 0xb1: case 0xb2: debug("Configuring IDT for PCIe SATA for srds_prctl:%x\n", serdes2_prtcl); -- 1.7.6.GIT

2 1