September 2013 - U-Boot

[U-Boot] [PATCH] powerpc/t1040qds: Add T1040QDS board
by Prabhakar Kushwaha 11 Sep '13

11 Sep '13

T1040QDS is a high-performance computing evaluation, development and test platform supporting the T1040 QorIQ Power Architecture™ processor. T1040QDS board Overview ----------------------- - Four e5500 cores, each with a private 256 KB L2 cache - 256 KB shared L3 CoreNet platform cache (CPC) - Interconnect CoreNet platform - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: - Packet parsing, classification, and distribution - Queue management for scheduling, packet sequencing, and congestion management - Cryptography Acceleration - RegEx Pattern Matching Acceleration - IEEE Std 1588 support - Hardware buffer management for buffer allocation and deallocation - Ethernet interfaces - Integrated 8-port Gigabit Ethernet switch - Four 1 Gbps Ethernet controllers - SERDES Connections, 8 lanes supporting: — PCI Express: supporting Gen 1 and Gen 2; — SGMII — QSGMII — SATA 2.0 — Aurora debug with dedicated connectors - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and Interleaving -IFC/Local Bus - NAND flash: 8-bit, async, up to 2GB. - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB - GASIC: Simple (minimal) target within Qixis FPGA - PromJET rapid memory download support - Ethernet - Two on-board RGMII 10/100/1G ethernet ports. - PHY #0 remains powered up during deep-sleep - QIXIS System Logic FPGA - Clocks - System and DDR clock (SYSCLK, “DDRCLK”) - SERDES clocks - Power Supplies - Video - DIU supports video at up to 1280x1024x32bpp - USB - Supports two USB 2.0 ports with integrated PHYs — Two type A ports with 5V(a)1.5A per port. — Second port can be converted to OTG mini-AB - SDHC - SDHC port connects directly to an adapter card slot, featuring: - Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC — Supporting eMMC memory devices - SPI - On-board support of 3 different devices and sizes - Other IO - Two Serial ports - ProfiBus port - Four I2C ports Signed-off-by: Poonam Aggrwal <poonam.aggrwal(a)freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain(a)freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar(a)freescale.com> --- This patch depends upon powerpc: Fix CamelCase checkpatch warning in DDR related code http://patchwork.ozlabs.org/patch/271670/ TODO: Add support of ethernet. MAINTAINERS | 2 + board/freescale/common/qixis.h | 4 +- board/freescale/t1040qds/Makefile | 38 ++ board/freescale/t1040qds/README | 169 +++++++ board/freescale/t1040qds/ddr.c | 117 +++++ board/freescale/t1040qds/ddr.h | 50 ++ board/freescale/t1040qds/eth.c | 34 ++ board/freescale/t1040qds/law.c | 32 ++ board/freescale/t1040qds/pci.c | 23 + board/freescale/t1040qds/t1040qds.c | 258 ++++++++++ board/freescale/t1040qds/t1040qds.h | 13 + board/freescale/t1040qds/t1040qds_qixis.h | 36 ++ board/freescale/t1040qds/tlb.c | 108 ++++ boards.cfg | 1 + drivers/net/fm/Makefile | 1 + drivers/net/fm/t1040.c | 16 + include/configs/T1040QDS.h | 761 +++++++++++++++++++++++++++++ 17 files changed, 1662 insertions(+), 1 deletion(-) create mode 100644 board/freescale/t1040qds/Makefile create mode 100644 board/freescale/t1040qds/README create mode 100644 board/freescale/t1040qds/ddr.c create mode 100644 board/freescale/t1040qds/ddr.h create mode 100644 board/freescale/t1040qds/eth.c create mode 100644 board/freescale/t1040qds/law.c create mode 100644 board/freescale/t1040qds/pci.c create mode 100644 board/freescale/t1040qds/t1040qds.c create mode 100644 board/freescale/t1040qds/t1040qds.h create mode 100644 board/freescale/t1040qds/t1040qds_qixis.h create mode 100644 board/freescale/t1040qds/tlb.c create mode 100644 drivers/net/fm/t1040.c create mode 100644 include/configs/T1040QDS.h diff --git a/MAINTAINERS b/MAINTAINERS index 0807727..52fbb86 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -27,6 +27,8 @@ Poonam Aggrwal <poonam.aggrwal(a)freescale.com> BSC9131RDB BSC9131 + T1040QDS T1040 + Naveen Burmi <NaveenBurmi(a)freescale.com> BSC9132QDS BSC9132 diff --git a/board/freescale/common/qixis.h b/board/freescale/common/qixis.h index 26e2eeb..d8fed14 100644 --- a/board/freescale/common/qixis.h +++ b/board/freescale/common/qixis.h @@ -79,7 +79,9 @@ struct qixis { u8 clk_freq[6]; /* Clock Measurement Registers */ u8 res_c6[8]; u8 clk_base[2]; /* Clock Frequency Base Reg */ - u8 res_d0[16]; + u8 res_d0[8]; + u8 cms[2]; /* Core Management Space Address Register, 0xD8 */ + u8 res_c0[6]; u8 aux2[4]; /* Auxiliary Registers,0xE0 */ u8 res14[10]; u8 aux_ad; diff --git a/board/freescale/t1040qds/Makefile b/board/freescale/t1040qds/Makefile new file mode 100644 index 0000000..0fa38e9 --- /dev/null +++ b/board/freescale/t1040qds/Makefile @@ -0,0 +1,38 @@ +# +# Copyright 2013 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-y += eth.o +COBJS-$(CONFIG_PCI) += pci.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/t1040qds/README b/board/freescale/t1040qds/README new file mode 100644 index 0000000..f8b53b4 --- /dev/null +++ b/board/freescale/t1040qds/README @@ -0,0 +1,169 @@ +Overview +-------- +The T1040QDS is a Freescale reference board that hosts the T1040 SoC +(and variants). + +T1040 SoC Overview +------------------ +The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA +processor cores with high-performance data path acceleration architecture +and network peripheral interfaces required for networking & telecommunications. + +The T1040/T1042 SoC includes the following function and features: + + - Four e5500 cores, each with a private 256 KB L2 cache + - 256 KB shared L3 CoreNet platform cache (CPC) + - Interconnect CoreNet platform + - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving + support + - Data Path Acceleration Architecture (DPAA) incorporating acceleration + for the following functions: + - Packet parsing, classification, and distribution + - Queue management for scheduling, packet sequencing, and congestion + management + - Cryptography Acceleration (SEC 5.0) + - RegEx Pattern Matching Acceleration (PME 2.2) + - IEEE Std 1588 support + - Hardware buffer management for buffer allocation and deallocation + - Ethernet interfaces + - Integrated 8-port Gigabit Ethernet switch (T1040 only) + - Four 1 Gbps Ethernet controllers + - Two RGMII interfaces or one RGMII and one MII interfaces + - High speed peripheral interfaces + - Four PCI Express 2.0 controllers running at up to 5 GHz + - Two SATA controllers supporting 1.5 and 3.0 Gb/s operation + - Upto two QSGMII interface + - Upto six SGMII interface supporting 1000 Mbps + - One SGMII interface supporting upto 2500 Mbps + - Additional peripheral interfaces + - Two USB 2.0 controllers with integrated PHY + - SD/eSDHC/eMMC + - eSPI controller + - Four I2C controllers + - Four UARTs + - Four GPIO controllers + - Integrated flash controller (IFC) + - LCD and HDMI interface (DIU) with 12 bit dual data rate + - TDM interface + - Multicore programmable interrupt controller (PIC) + - Two 8-channel DMA engines + - Single source clocking implementation + - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) + + T1040QDS board Overview + ----------------------- + - SERDES Connections, 8 lanes supporting: + — PCI Express: supporting Gen 1 and Gen 2; + — SGMII + — QSGMII + — SATA 2.0 + — Aurora debug with dedicated connectors (T1040 only) + - DDR Controller + - Supports rates of up to 1600 MHz data-rate + - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types. + -IFC/Local Bus + - NAND flash: 8-bit, async, up to 2GB. + - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB + - GASIC: Simple (minimal) target within Qixis FPGA + - PromJET rapid memory download support + - Ethernet + - Two on-board RGMII 10/100/1G ethernet ports. + - PHY #0 remains powered up during deep-sleep (T1040 only) + - QIXIS System Logic FPGA + - Clocks + - System and DDR clock (SYSCLK, “DDRCLK”) + - SERDES clocks + - Power Supplies + - Video + - DIU supports video at up to 1280x1024x32bpp + - USB + - Supports two USB 2.0 ports with integrated PHYs + — Two type A ports with 5V(a)1.5A per port. + — Second port can be converted to OTG mini-AB + - SDHC + - SDHC port connects directly to an adapter card slot, featuring: + - Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC + — Supporting eMMC memory devices + - SPI + - On-board support of 3 different devices and sizes + - Other IO + - Two Serial ports + - ProfiBus port + - Four I2C ports + +Memory map on T1040QDS +---------------------- +The addresses in brackets are physical addresses. + +Start Address End Address Description Size +0xF_FFDF_0000 0xF_FFDF_0FFF IFC - FPGA 4KB +0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB +0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB +0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB +0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB +0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB +0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB +0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB +0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB +0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB +0xF_E000_0000 0xF_E7FF_FFFF Promjet 128MB +0xF_0000_0000 0xF_003F_FFFF DCSR 4MB +0xC_3000_0000 0xC_3FFF_FFFF PCI Express 4 Mem Space 256MB +0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB +0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB +0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB +0x0_0000_0000 0x0_ffff_ffff DDR 2GB + + +NOR Flash memory Map on T1040QDS +-------------------------------- + Start End Definition Size +0xEFF80000 0xEFFFFFFF u-boot (current bank) 512KB +0xEFF60000 0xEFF7FFFF u-boot env (current bank) 128KB +0xEFF40000 0xEFF5FFFF FMAN Ucode (current bank) 128KB +0xED300000 0xEFF3FFFF rootfs (alt bank) 44MB + 256KB +0xEC800000 0xEC8FFFF Hardware device tree (alt bank) 1MB +0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB +0xEC000000 0xEC01FFFF RCW (alt bank) 128KB +0xEBF80000 0xEBFFFFFF u-boot (alt bank) 512KB +0xEBF60000 0xEBF7FFFF u-boot env (alt bank) 128KB +0xEBF40000 0xEBF5FFFF FMAN ucode (alt bank) 128KB +0xE9300000 0xEBF3FFFF rootfs (current bank) 44MB + 256KB +0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 11MB + 512KB +0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB +0xE8000000 0xE801FFFF RCW (current bank) 128KB + + +Various Software configurations/environment variables/commands +-------------------------------------------------------------- +The below commands apply to T1040QDS + +1. U-boot environment variable hwconfig + The default hwconfig is: + hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1: + dr_mode=host,phy_type=utmi + Note: For USB gadget set "dr_mode=peripheral" + +2. FMAN Ucode versions + fsl_fman_ucode_t1040.bin + +3. Switching to alternate bank + Commands for switching to alternate bank. + + 1. To change from vbank0 to vbank4 + => qixis_reset altbank (it will boot using vbank4) + + 2.To change from vbank4 to vbank0 + => qixis reset (it will boot using vbank0) + +T1040 Personality +-------------------- + +T1022 Personality +-------------------- +T1022 is a reduced personality of T1040 with less core/clusters. + +T1042 Personality +-------------------- +T1042 is a reduced personality of T1040 without Integrated 8-port Gigabit +Ethernet switch. Rest of the blocks are same as T1040 diff --git a/board/freescale/t1040qds/ddr.c b/board/freescale/t1040qds/ddr.c new file mode 100644 index 0000000..4fd17da --- /dev/null +++ b/board/freescale/t1040qds/ddr.c @@ -0,0 +1,117 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <hwconfig.h> +#include <asm/mmu.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> +#include <asm/fsl_law.h> +#include "ddr.h" + +DECLARE_GLOBAL_DATA_PTR; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; + ulong ddr_freq; + + if (ctrl_num > 2) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + if (!pdimm->n_ranks) + return; + + pbsp = udimms[0]; + + /* Get clk_adjust, cpo, write_data_delay,2t, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + while (pbsp->datarate_mhz_high) { + if (pbsp->n_ranks == pdimm->n_ranks && + (pdimm->rank_density >> 30) >= pbsp->rank_gb) { + if (ddr_freq <= pbsp->datarate_mhz_high) { + popts->cpo_override = pbsp->cpo; + popts->write_data_delay = + pbsp->write_data_delay; + popts->clk_adjust = pbsp->clk_adjust; + popts->wrlvl_start = pbsp->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + popts->twot_en = pbsp->force_2t; + goto found; + } + pbsp_highest = pbsp; + } + pbsp++; + } + + if (pbsp_highest) { + printf("Error: board specific timing not found\n"); + printf("for data rate %lu MT/s\n", ddr_freq); + printf("Trying to use the highest speed (%u) parameters\n", + pbsp_highest->datarate_mhz_high); + popts->cpo_override = pbsp_highest->cpo; + popts->write_data_delay = pbsp_highest->write_data_delay; + popts->clk_adjust = pbsp_highest->clk_adjust; + popts->wrlvl_start = pbsp_highest->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + popts->twot_en = pbsp_highest->force_2t; + } else { + panic("DIMM is not supported by this board"); + } +found: + debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n" + "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, " + "wrlvl_ctrl_3 0x%x\n", + pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb, + pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2, + pbsp->wrlvl_ctl_3); + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * rtt and rtt_wr override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size; + + puts("Initializing....using SPD\n"); + + dram_size = fsl_ddr_sdram(); + + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; + + puts(" DDR: "); + return dram_size; +} diff --git a/board/freescale/t1040qds/ddr.h b/board/freescale/t1040qds/ddr.h new file mode 100644 index 0000000..8ee206e --- /dev/null +++ b/board/freescale/t1040qds/ddr.h @@ -0,0 +1,50 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __DDR_H__ +#define __DDR_H__ +struct board_specific_parameters { + u32 n_ranks; + u32 datarate_mhz_high; + u32 rank_gb; + u32 clk_adjust; + u32 wrlvl_start; + u32 wrlvl_ctl_2; + u32 wrlvl_ctl_3; + u32 cpo; + u32 write_data_delay; + u32 force_2t; +}; + +/* + * These tables contain all valid speeds we want to override with board + * specific parameters. datarate_mhz_high values need to be in ascending order + * for each n_ranks group. + */ + +static const struct board_specific_parameters udimm0[] = { + /* + * memory controller 0 + * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T + * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay | + */ + {2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, + {2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09, 0xff, 2, 0}, + {2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b, 0xff, 2, 0}, + {2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a, 0xff, 2, 0}, + {2, 1900, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0}, + {2, 2140, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0}, + {1, 1350, 0, 5, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, + {1, 1700, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0}, + {1, 1900, 0, 4, 8, 0x080a0a0c, 0x0e0e0f0a, 0xff, 2, 0}, + {1, 2140, 0, 4, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0}, + {} +}; + +static const struct board_specific_parameters *udimms[] = { + udimm0, +}; +#endif diff --git a/board/freescale/t1040qds/eth.c b/board/freescale/t1040qds/eth.c new file mode 100644 index 0000000..c0604a4 --- /dev/null +++ b/board/freescale/t1040qds/eth.c @@ -0,0 +1,34 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <netdev.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <malloc.h> +#include <fm_eth.h> +#include <fsl_mdio.h> +#include <miiphy.h> +#include <phy.h> +#include <asm/fsl_dtsec.h> +#include <asm/fsl_serdes.h> +#include "../common/qixis.h" +#include "../common/fman.h" + +#include "t1040qds_qixis.h" + +void fdt_fixup_board_enet(void *fdt) +{ + return; +} diff --git a/board/freescale/t1040qds/law.c b/board/freescale/t1040qds/law.c new file mode 100644 index 0000000..a2dc027 --- /dev/null +++ b/board/freescale/t1040qds/law.c @@ -0,0 +1,32 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { +#ifndef CONFIG_SYS_NO_FLASH + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), +#endif +#ifdef QIXIS_BASE_PHYS + SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/t1040qds/pci.c b/board/freescale/t1040qds/pci.c new file mode 100644 index 0000000..c53e3b7 --- /dev/null +++ b/board/freescale/t1040qds/pci.c @@ -0,0 +1,23 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/fsl_pci.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <asm/fsl_serdes.h> + +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/freescale/t1040qds/t1040qds.c b/board/freescale/t1040qds/t1040qds.c new file mode 100644 index 0000000..02c8081 --- /dev/null +++ b/board/freescale/t1040qds/t1040qds.c @@ -0,0 +1,258 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <i2c.h> +#include <netdev.h> +#include <linux/compiler.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <fm_eth.h> + +#include "../common/qixis.h" +#include "t1040qds.h" +#include "t1040qds_qixis.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + char buf[64]; + u8 sw; + struct cpu_type *cpu = gd->arch.cpu; + static const char *const freq[] = {"100", "125", "156.25", "161.13", + "122.88", "122.88", "122.88"}; + int clock; + + printf("Board: %sQDS, ", cpu->name); + printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, ", + QIXIS_READ(id), QIXIS_READ(arch)); + + sw = QIXIS_READ(brdcfg[0]); + sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; + + if (sw < 0x8) + printf("vBank: %d\n", sw); + else if (sw == 0x8) + puts("PromJet\n"); + else if (sw == 0x9) + puts("NAND\n"); + else if (sw == 0x15) + printf("IFCCard\n"); + else + printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH); + + printf("FPGA: v%d (%s), build %d", + (int)QIXIS_READ(scver), qixis_read_tag(buf), + (int)qixis_read_minor()); + /* the timestamp string contains "\n" at the end */ + printf(" on %s", qixis_read_time(buf)); + + /* + * Display the actual SERDES reference clocks as configured by the + * dip switches on the board. Note that the SWx registers could + * technically be set to force the reference clocks to match the + * values that the SERDES expects (or vice versa). For now, however, + * we just display both values and hope the user notices when they + * don't match. + */ + puts("SERDES Reference: "); + sw = QIXIS_READ(brdcfg[2]); + clock = (sw >> 6) & 3; + printf("Clock1=%sMHz ", freq[clock]); + clock = (sw >> 4) & 3; + printf("Clock2=%sMHz\n", freq[clock]); + + return 0; +} + +int select_i2c_ch_pca9547(u8 ch) +{ + int ret; + + ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); + if (ret) { + puts("PCA: failed to select proper channel\n"); + return ret; + } + + return 0; +} + +int board_early_init_r(void) +{ +#ifdef CONFIG_SYS_FLASH_BASE + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash + PROMJET region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash + promjet */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); +#endif + set_liodns(); +#ifdef CONFIG_SYS_DPAA_QBMAN + setup_portals(); +#endif + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + + return 0; +} + +unsigned long get_board_sys_clk(void) +{ + u8 sysclk_conf = QIXIS_READ(brdcfg[1]); + + switch (sysclk_conf & 0x0F) { + case QIXIS_SYSCLK_64: + return 64000000; + case QIXIS_SYSCLK_83: + return 83333333; + case QIXIS_SYSCLK_100: + return 100000000; + case QIXIS_SYSCLK_125: + return 125000000; + case QIXIS_SYSCLK_133: + return 133333333; + case QIXIS_SYSCLK_150: + return 150000000; + case QIXIS_SYSCLK_160: + return 160000000; + case QIXIS_SYSCLK_166: + return 166666666; + } + return 66666666; +} + +unsigned long get_board_ddr_clk(void) +{ + u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); + + switch ((ddrclk_conf & 0x30) >> 4) { + case QIXIS_DDRCLK_100: + return 100000000; + case QIXIS_DDRCLK_125: + return 125000000; + case QIXIS_DDRCLK_133: + return 133333333; + } + return 66666666; +} + +static const char *serdes_clock_to_string(u32 clock) +{ + switch (clock) { + case SRDS_PLLCR0_RFCK_SEL_100: + return "100"; + case SRDS_PLLCR0_RFCK_SEL_125: + return "125"; + case SRDS_PLLCR0_RFCK_SEL_156_25: + return "156.25"; + default: + return "Unknown frequency"; + } +} + +#define NUM_SRDS_BANKS 2 +int misc_init_r(void) +{ + u8 sw; + serdes_corenet_t *srds_regs = + (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; + u32 actual[NUM_SRDS_BANKS] = { 0 }; + int i; + + sw = QIXIS_READ(brdcfg[2]); + for (i = 0; i < NUM_SRDS_BANKS; i++) { + unsigned int clock = (sw >> (6 - 2 * i)) & 3; + switch (clock) { + case 0: + actual[i] = SRDS_PLLCR0_RFCK_SEL_100; + break; + case 1: + actual[i] = SRDS_PLLCR0_RFCK_SEL_125; + break; + case 2: + actual[i] = SRDS_PLLCR0_RFCK_SEL_156_25; + break; + } + } + + for (i = 0; i < NUM_SRDS_BANKS; i++) { + u32 pllcr0 = srds_regs->bank[i].pllcr0; + u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK; + if (expected != actual[i]) { + printf("Warning: SERDES bank %u expects reference clock" + " %sMHz, but actual is %sMHz\n", i + 1, + serdes_clock_to_string(expected), + serdes_clock_to_string(actual[i])); + } + } + + + + return 0; +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); + +#ifdef CONFIG_HAS_FSL_DR_USB + fdt_fixup_dr_usb(blob, bd); +#endif + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); + fdt_fixup_board_enet(blob); +#endif +} + +void qixis_dump_switch(void) +{ + int i, nr_of_cfgsw; + + QIXIS_WRITE(cms[0], 0x00); + nr_of_cfgsw = QIXIS_READ(cms[1]); + + puts("DIP switch settings dump:\n"); + for (i = 1; i <= nr_of_cfgsw; i++) { + QIXIS_WRITE(cms[0], i); + printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1])); + } +} diff --git a/board/freescale/t1040qds/t1040qds.h b/board/freescale/t1040qds/t1040qds.h new file mode 100644 index 0000000..79bdeda --- /dev/null +++ b/board/freescale/t1040qds/t1040qds.h @@ -0,0 +1,13 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __T1040_QDS_H__ +#define __T1040_QDS_H__ + +void fdt_fixup_board_enet(void *blob); +void pci_of_setup(void *blob, bd_t *bd); + +#endif diff --git a/board/freescale/t1040qds/t1040qds_qixis.h b/board/freescale/t1040qds/t1040qds_qixis.h new file mode 100644 index 0000000..2ce8795 --- /dev/null +++ b/board/freescale/t1040qds/t1040qds_qixis.h @@ -0,0 +1,36 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __T1040QDS_QIXIS_H__ +#define __T1040QDS_QIXIS_H__ + +/* Definitions of QIXIS Registers for T1040QDS */ + +/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */ +#define BRDCFG4_EMISEL_MASK 0xE0 +#define BRDCFG4_EMISEL_SHIFT 5 + +/* SYSCLK */ +#define QIXIS_SYSCLK_66 0x0 +#define QIXIS_SYSCLK_83 0x1 +#define QIXIS_SYSCLK_100 0x2 +#define QIXIS_SYSCLK_125 0x3 +#define QIXIS_SYSCLK_133 0x4 +#define QIXIS_SYSCLK_150 0x5 +#define QIXIS_SYSCLK_160 0x6 +#define QIXIS_SYSCLK_166 0x7 +#define QIXIS_SYSCLK_64 0x8 + +/* DDRCLK */ +#define QIXIS_DDRCLK_66 0x0 +#define QIXIS_DDRCLK_100 0x1 +#define QIXIS_DDRCLK_125 0x2 +#define QIXIS_DDRCLK_133 0x3 + + +#define QIXIS_SRDS1CLK_122 0x5a +#define QIXIS_SRDS1CLK_125 0x5e +#endif diff --git a/board/freescale/t1040qds/tlb.c b/board/freescale/t1040qds/tlb.c new file mode 100644 index 0000000..412c591 --- /dev/null +++ b/board/freescale/t1040qds/tlb.c @@ -0,0 +1,108 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ +#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) + /* + * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the + * SRAM is at 0xfffc0000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256K, 1), +#else + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#endif + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + + /* *I*G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256K, 1), + + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 5, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 7, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 8, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 9, BOOKE_PAGESZ_4M, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE + /* + * *I*G - NAND + * entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so we use entry 16 for nand. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_64K, 1), +#endif +#ifdef QIXIS_BASE + SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 11, BOOKE_PAGESZ_4K, 1), +#endif + +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index 48aa0bf..1aa4f82 100644 --- a/boards.cfg +++ b/boards.cfg @@ -955,6 +955,7 @@ B4860QDS_SRIO_PCIE_BOOT powerpc mpc85xx b4860qds freesca B4420QDS powerpc mpc85xx b4860qds freescale - B4860QDS:PPC_B4420 B4420QDS_NAND powerpc mpc85xx b4860qds freescale - B4860QDS:PPC_B4420,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000 B4420QDS_SPIFLASH powerpc mpc85xx b4860qds freescale - B4860QDS:PPC_B4420,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 +T1040QDS powerpc mpc85xx t1040qds freescale - T1040QDS:PPC_T1040 xpedite520x powerpc mpc85xx - xes xpedite537x powerpc mpc85xx - xes xpedite550x powerpc mpc85xx - xes diff --git a/drivers/net/fm/Makefile b/drivers/net/fm/Makefile index 4edd849..dddde4f 100644 --- a/drivers/net/fm/Makefile +++ b/drivers/net/fm/Makefile @@ -29,6 +29,7 @@ COBJS-$(CONFIG_PPC_P3041) += p5020.o COBJS-$(CONFIG_PPC_P4080) += p4080.o COBJS-$(CONFIG_PPC_P5020) += p5020.o COBJS-$(CONFIG_PPC_P5040) += p5040.o +COBJS-$(CONFIG_PPC_T1040) += t1040.o COBJS-$(CONFIG_PPC_T4240) += t4240.o COBJS-$(CONFIG_PPC_T4160) += t4240.o COBJS-$(CONFIG_PPC_B4420) += b4860.o diff --git a/drivers/net/fm/t1040.c b/drivers/net/fm/t1040.c new file mode 100644 index 0000000..83cf081 --- /dev/null +++ b/drivers/net/fm/t1040.c @@ -0,0 +1,16 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#include <common.h> +#include <phy.h> +#include <fm_eth.h> +#include <asm/io.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_serdes.h> + +phy_interface_t fman_port_enet_if(enum fm_port port) +{ + return PHY_INTERFACE_MODE_NONE; +} diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h new file mode 100644 index 0000000..2738242 --- /dev/null +++ b/include/configs/T1040QDS.h @@ -0,0 +1,761 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * T1040 QDS board configuration file + */ +#define CONFIG_T1040QDS +#define CONFIG_PHYS_64BIT + +#ifdef CONFIG_RAMBOOT_PBL +#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#endif + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_E500MC /* BOOKE e500mc family */ +#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ +#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */ +#define CONFIG_MP /* support multiple processors */ + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff80000 +#endif + +#ifndef CONFIG_RESET_VECTOR_ADDRESS +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc +#endif + +#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ +#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS +#define CONFIG_FSL_IFC /* Enable IFC Support */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_PCIE2 /* PCIE controler 2 */ +#define CONFIG_PCIE3 /* PCIE controler 3 */ +#define CONFIG_PCIE4 /* PCIE controler 4 */ + +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +#define CONFIG_ENV_OVERWRITE + +#ifdef CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_NOWHERE +#else +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#endif + +#ifndef CONFIG_SYS_NO_FLASH +#if defined(CONFIG_SPIFLASH) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ +#define CONFIG_ENV_SECT_SIZE 0x10000 +#elif defined(CONFIG_SDCARD) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_OFFSET (512 * 1105) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif +#else /* CONFIG_SYS_NO_FLASH */ +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif + +#ifndef __ASSEMBLY__ +unsigned long get_board_sys_clk(void); +unsigned long get_board_ddr_clk(void); +#endif + +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_SYS_CACHE_STASHING +#define CONFIG_BACKSIDE_L2_CACHE +#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_DDR_ECC +#ifdef CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#endif + +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ + +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* + * Config the L3 Cache as L3 SRAM + */ +#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 + +#define CONFIG_SYS_DCSRBAR 0xf0000000 +#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +/* + * DDR Setup + */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */ +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) + +#define CONFIG_DDR_SPD +#define CONFIG_FSL_DDR3 +#define CONFIG_FSL_DDR_INTERACTIVE + +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x51 + +#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ + +/* + * IFC Definitions + */ +#define CONFIG_SYS_FLASH_BASE 0xe0000000 +#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) + +#define CONFIG_SYS_NOR0_CSPR_EXT (0xf) +#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ + + 0x8000000) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR1_CSPR_EXT (0xf) +#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) +/* NOR Flash Timing Params */ +#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ + FTIM0_NOR_TEADC(0x5) | \ + FTIM0_NOR_TEAHC(0x5)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ + FTIM1_NOR_TRAD_NOR(0x1A) |\ + FTIM1_NOR_TSEQRAD_NOR(0x13)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ + FTIM2_NOR_TCH(0x4) | \ + FTIM2_NOR_TWPH(0x0E) | \ + FTIM2_NOR_TWP(0x1c)) +#define CONFIG_SYS_NOR_FTIM3 0x0 + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ + + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} +#define CONFIG_FSL_QIXIS /* use common QIXIS code */ +#define QIXIS_BASE 0xffdf0000 +#define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) +#define QIXIS_LBMAP_SWITCH 0x06 +#define QIXIS_LBMAP_MASK 0x0f +#define QIXIS_LBMAP_SHIFT 0 +#define QIXIS_LBMAP_DFLTBANK 0x00 +#define QIXIS_LBMAP_ALTBANK 0x04 +#define QIXIS_RST_CTL_RESET 0x31 +#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 +#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 +#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 + +#define CONFIG_SYS_CSPR3_EXT (0xf) +#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_GPCM \ + | CSPR_V) +#define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024) +#define CONFIG_SYS_CSOR3 0x0 +/* QIXIS Timing parameters for IFC CS3 */ +#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ + FTIM0_GPCM_TEADC(0x0e) | \ + FTIM0_GPCM_TEAHC(0x0e)) +#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ + FTIM1_GPCM_TRAD(0x3f)) +#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ + FTIM2_GPCM_TCH(0x0) | \ + FTIM2_GPCM_TWP(0x1f)) +#define CONFIG_SYS_CS3_FTIM3 0x0 + +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_BASE 0xff800000 +#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) + +#define CONFIG_SYS_NAND_CSPR_EXT (0xf) +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ + | CSPR_MSEL_NAND /* MSEL = NAND */ \ + | CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) + +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ + | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ + | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ + | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ + | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +/* ONFI NAND Flash mode0 Timing Params */ +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ + FTIM0_NAND_TWP(0x18) | \ + FTIM0_NAND_TWCHT(0x07) | \ + FTIM0_NAND_TWH(0x0a)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ + FTIM1_NAND_TWBE(0x39) | \ + FTIM1_NAND_TRR(0x0e) | \ + FTIM1_NAND_TRP(0x18)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ + FTIM2_NAND_TREH(0x0a) | \ + FTIM2_NAND_TWHRE(0x1e)) +#define CONFIG_SYS_NAND_FTIM3 0x0 + +#define CONFIG_SYS_NAND_DDR_LAW 11 +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND + +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +#if defined(CONFIG_NAND) +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT +#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR +#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 +#else +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 +#endif + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#if defined(CONFIG_RAMBOOT_PBL) +#define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_MISC_INIT_R + +#define CONFIG_HWCONFIG + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) +#define CONFIG_SERIAL_MULTI /* Enable both serial ports */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ +#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000 + +#define I2C_MUX_PCA_ADDR 0x77 +#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/ + + +/* I2C bus multiplexer */ +#define I2C_MUX_CH_DEFAULT 0x8 + +/* + * RTC configuration + */ +#define RTC +#define CONFIG_RTC_DS3231 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_FSL_ESPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SPI_FLASH_SST +#define CONFIG_SPI_FLASH_EON +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE 0 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +#ifdef CONFIG_PCI +/* controller 1, direct to uli, tgtid 3, Base address 20000 */ +#ifdef CONFIG_PCIE1 +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 2, Slot 2, tgtid 2, Base address 201000 */ +#ifdef CONFIG_PCIE2 +#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 3, Slot 1, tgtid 1, Base address 202000 */ +#ifdef CONFIG_PCIE3 +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 4, Base address 203000 */ +#ifdef CONFIG_PCIE4 +#define CONFIG_SYS_PCIE4_MEM_VIRT 0xb0000000 +#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc30000000ull +#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE4_IO_VIRT 0xf8030000 +#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull +#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ +#endif + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_E1000 + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif /* CONFIG_PCI */ + +/* SATA */ +#define CONFIG_FSL_SATA_V2 +#ifdef CONFIG_FSL_SATA_V2 +#define CONFIG_LIBATA +#define CONFIG_FSL_SATA + +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SATA2 +#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA + +#define CONFIG_LBA48 +#define CONFIG_CMD_SATA +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +#endif + +/* +* USB +*/ +#define CONFIG_HAS_FSL_DR_USB + +#ifdef CONFIG_HAS_FSL_DR_USB +#define CONFIG_USB_EHCI + +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_CMD_EXT2 +#endif +#endif + +#define CONFIG_MMC + +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* Qman/Bman */ +#ifndef CONFIG_NOBQFMAN +#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ +#define CONFIG_SYS_BMAN_NUM_PORTALS 25 +#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 +#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull +#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 +#define CONFIG_SYS_QMAN_NUM_PORTALS 25 +#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 +#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull +#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 + +#define CONFIG_SYS_DPAA_FMAN +#define CONFIG_SYS_DPAA_PME + +/* Default address of microcode for the Linux Fman driver */ +#if defined(CONFIG_SPIFLASH) +/* + * env is stored at 0x100000, sector size is 0x10000, ucode is stored after + * env, so we got 0x110000. + */ +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000 +#elif defined(CONFIG_SDCARD) +/* + * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is + * about 545KB (1089 blocks), Env is stored after the image, and the env size is + * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_MMC +#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_QE_FMAN_FW_IN_NAND +#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000 +#endif +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) +#endif /* CONFIG_NOBQFMAN */ + +#ifdef CONFIG_SYS_DPAA_FMAN +#define CONFIG_FMAN_ENET +#define CONFIG_PHYLIB_10G +#define CONFIG_PHY_VITESSE +#define CONFIG_PHY_REALTEK +#define CONFIG_PHY_TERANETICS +#define SGMII_CARD_PORT1_PHY_ADDR 0x1C +#define SGMII_CARD_PORT2_PHY_ADDR 0x10 +#define SGMII_CARD_PORT3_PHY_ADDR 0x1E +#define SGMII_CARD_PORT4_PHY_ADDR 0x11 +#endif + +#ifdef CONFIG_FMAN_ENET +#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x10 +#define CONFIG_SYS_FM1_DTSEC6_PHY_ADDR 0x11 +#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 4 + +#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c +#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d +#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e +#define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC1" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* + * Environment + */ +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ERRATA +#define CONFIG_CMD_GREPENV +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SETEXPR + +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ + +#define CONFIG_BAUDRATE 115200 + +#define __USB_PHY_TYPE utmi + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ + "bank_intlv=cs0_cs1;" \ + "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ + "netdev=eth0\0" \ + "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ + "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot && " \ + "protect off $ubootaddr +$filesize && " \ + "erase $ubootaddr +$filesize && " \ + "cp.b $loadaddr $ubootaddr $filesize && " \ + "protect on $ubootaddr +$filesize && " \ + "cmp.b $loadaddr $ubootaddr $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=t1040qds/ramdisk.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=t1040qds/t1040qds.dtb\0" \ + "bdev=sda3\0" \ + "c=ffe\0" + +#define CONFIG_LINUX \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "setenv ramdiskaddr 0x02000000;" \ + "setenv fdtaddr 0x00c00000;" \ + "setenv loadaddr 0x1000000;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_HDBOOT \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_LINUX + +#ifdef CONFIG_SECURE_BOOT +#include <asm/fsl_secure_boot.h> +#endif + +#endif /* __CONFIG_H */ -- 1.7.9.5

3 4

[U-Boot] [PATCH] mxs_nand: Fix ECC strength for NAND flash with OOB size of 224
by Elie De Brauwer 11 Sep '13

11 Sep '13

On a board with an i.mx28 and a Micron MT29F4G08ABAEAH4, Linux says: NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABAEAH4), 512MiB, page size: 4096, OOB size: 224) the ECC strength is 16. root@(none):/sys/devices/virtual/mtd/mtd0# for i in ecc_strength oobsize subpagesize; do echo $i = `cat $i`; done ecc_strength = 16 oobsize = 224 subpagesize = 4096 The ECC strength was not properly discovered by U-Boot causing the data written by Linux to return an -74 (EBADMSG) when read from U-Boot. This patch fixes mxs_nand_get_ecc_strength() to function in case of a NAND flash with page_data_size = 4096 and page_oob_size= 224. Signed-off-by: Elie De Brauwer <eliedebrauwer(a)gmail.com> --- drivers/mtd/nand/mxs_nand.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/mtd/nand/mxs_nand.c b/drivers/mtd/nand/mxs_nand.c index 378f8c5..036c113 100644 --- a/drivers/mtd/nand/mxs_nand.c +++ b/drivers/mtd/nand/mxs_nand.c @@ -155,6 +155,9 @@ static inline uint32_t mxs_nand_get_ecc_strength(uint32_t page_data_size, if (page_oob_size == 218) return 16; + + if (page_oob_size == 224) + return 16; } return 0; -- 1.7.10.4

3 4

[U-Boot] [PATCH v1 0/7] The patchset fixes some issue in the generation of the imx image
by Stefano Babic 11 Sep '13

11 Sep '13

(header for Freescale's i.MX processors) to allow the usage of Freescale's tools to sign the u-boot image and provide a secure boot. This has nothing to do with the Secure Boot extensions implemented by Simon Glass, that can be in any case used to boot later a secure image. Freescale's secure boot ensures that a signed bootloader is started only if it is verified with a key that is burned into the iMX fuses. Documentation about the Freescale's secure process can be read from the AN4591, available on the Freescale's Website. The patchset allows to add to the imx Header the CSF (command Sequence File) generated by the tools provided by Freescale. The CSF is then simply concatenated to the u-boot image, making a signed bootloader, that the processor can verify if the fuses for the keys are burned. The processor (i.MX53 / i.MX6x) will not start a bootloader that cannot be verified - further infos how to configure the SOC to verify the bootloader can be found in the User Manual of the specific SOC. Next step is to verify the kernel, that can be still done using Simon's patches for verified boot (CONFIG_OF_CONTROL must be set in the board configuarion file). Stefano Babic (7): tools: imx_header should not include flash_offset tools: rename mximage_flash_offset to imximage_ivt_offset tools: dynamically allocate imx_header in imximage tools: add variable padding of data image in mkimage tools: add padding of data image file for imximage tools: add support for setting the CSF into imximage imx: add status reporting for HAB status arch/arm/cpu/armv7/mx6/Makefile | 2 +- arch/arm/cpu/armv7/mx6/hab.c | 127 ++++++++++++++++++++++ arch/arm/include/asm/arch-mx6/hab.h | 80 ++++++++++++++ arch/arm/include/asm/arch-mx6/imx-regs.h | 8 +- doc/README.imximage | 18 +++- doc/README.mxc_hab | 48 +++++++++ tools/imximage.c | 168 +++++++++++++++++++++++++++--- tools/imximage.h | 20 +++- tools/mkimage.c | 24 ++++- tools/mkimage.h | 5 +- 10 files changed, 471 insertions(+), 29 deletions(-) create mode 100644 arch/arm/cpu/armv7/mx6/hab.c create mode 100644 arch/arm/include/asm/arch-mx6/hab.h create mode 100644 doc/README.mxc_hab -- 1.7.9.5

9 49

[U-Boot] rename "findfdt" to, say, "selectfdt" or something similar?
by Robert P. J. Day 11 Sep '13

11 Sep '13

a bit of terminological pedantry but would it be more intuitive to rename the TI-related "findfdt" environment variable to something like "selectfdt" or "identifyfdt" or "determinefdt" or ... you get the idea. in my mind, "find" normally implies to go out and *find* something; that is, to search for it and determine its location. but all that's happening with "findfdt" is to determine the proper name of the fdt file based on the board name. i realize it sounds picky but twice already i've had to explain to a class that findfdt isn't really finding anything, it's just *setting* something that will actually be looked for later. thoughts? i can submit a patch if those higher up the food chain think there's value in this. rday -- ======================================================================== Robert P. J. Day Ottawa, Ontario, CANADA http://crashcourse.ca Twitter: http://twitter.com/rpjday LinkedIn: http://ca.linkedin.com/in/rpjday ========================================================================

1 0

[U-Boot] please pull u-boot-samsung master
by Minkyu Kang 11 Sep '13

11 Sep '13

Dear Albert, The following changes since commit 9ed887caecb9ecb0c68773a1870d143b9f28d3da: Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' (2013-08-17 18:24:13 +0200) are available in the git repository at: git://git.denx.de/u-boot-samsung master for you to fetch changes up to 5c18a1cf3e56e0177388258696be4a17a672e9d0: arm:goni:mmc: Add sd card detection and initialization. (2013-09-11 11:09:27 +0900) ---------------------------------------------------------------- Chander Kashyap (3): CONFIG: EXYNOS5: Replace misnomer SMDK5250 with EXYNOS5250 and update Makefiles exynos5250: Add arndale board support dts: samsung: arndale: Fix include path Inderpal Singh (1): exynos5250: arndale: Add mmc support Minkyu Kang (2): arm: smdkc100: remove config.mk file arm: goni: remove config.mk file Piotr Wilczek (2): arm:exynos:gpio: fix s5p_gpio_part_max for exynos4x12 drivers:power:max77686: add function to set voltage and mode Przemyslaw Marczak (2): arm:mmc:goni/exynos: Fix wrong mmc base register devices offset. arm:goni:mmc: Add sd card detection and initialization. MAINTAINERS | 4 + Makefile | 2 +- arch/arm/include/asm/arch-exynos/gpio.h | 17 +- arch/arm/include/asm/arch-exynos/mmc.h | 6 +- arch/arm/include/asm/arch-s5pc1xx/mmc.h | 6 +- board/samsung/arndale/Makefile | 34 ++++ board/samsung/arndale/arndale.c | 101 ++++++++++++ board/samsung/arndale/arndale_spl.c | 50 ++++++ board/samsung/dts/exynos5250-arndale.dts | 39 +++++ board/samsung/goni/config.mk | 18 --- board/samsung/goni/goni.c | 33 +++- board/samsung/smdkc100/config.mk | 16 -- boards.cfg | 1 + drivers/power/pmic/pmic_max77686.c | 192 ++++++++++++++++++++++ include/configs/arndale.h | 255 ++++++++++++++++++++++++++++++ include/configs/exynos5250-dt.h | 2 +- include/configs/s5p_goni.h | 3 + include/configs/smdkc100.h | 3 + include/power/max77686_pmic.h | 26 +++ tools/Makefile | 4 +- 20 files changed, 766 insertions(+), 46 deletions(-) create mode 100644 board/samsung/arndale/Makefile create mode 100644 board/samsung/arndale/arndale.c create mode 100644 board/samsung/arndale/arndale_spl.c create mode 100644 board/samsung/dts/exynos5250-arndale.dts delete mode 100644 board/samsung/goni/config.mk delete mode 100644 board/samsung/smdkc100/config.mk create mode 100644 include/configs/arndale.h -- Thanks, Minkyu Kang.

2 1

[U-Boot] [PATCH v3 0/4] USB: atmel: add atmel usba udc driver support
by Bo Shen 11 Sep '13

11 Sep '13

Add atmel usb udc driver support porting from Linux kernel. Using RNDIS gadget driver to test it. Test OK on at91sam9m10g45ek, at91sam9m10g45ek, and sama5d31ek boards. It need the patch from: Troy Kisky <troy.kisky(a)boundarydevices.com> (usb: gadget: config: fix unaligned access issues) more information: http://patchwork.ozlabs.org/patch/264151/ Changes in v3: - Add new (resubmit) one patch from Troy Kisky - Move common header file along with USB device driver Changes in v2: - Add detail information of the orignal code - Add a common header to hold atmel usba udc information for different SoCs Bo Shen (3): USB: gadget: add atmel usba udc driver ARM: atmel: correct UDPHS name ARM: atmel: add RNDIS gadget support Troy Kisky (1): usb: gadget: config: fix unaligned access issues arch/arm/cpu/armv7/at91/sama5d3_devices.c | 12 + arch/arm/include/asm/arch-at91/at91_common.h | 1 + arch/arm/include/asm/arch-at91/atmel_usba_udc.h | 64 ++ arch/arm/include/asm/arch-at91/sama5d3.h | 2 +- board/atmel/sama5d3xek/sama5d3xek.c | 13 + drivers/usb/gadget/Makefile | 1 + drivers/usb/gadget/atmel_usba_udc.c | 1305 +++++++++++++++++++++++ drivers/usb/gadget/atmel_usba_udc.h | 326 ++++++ drivers/usb/gadget/config.c | 6 +- include/configs/sama5d3xek.h | 8 + include/linux/usb/atmel_usba_udc.h | 26 + 11 files changed, 1761 insertions(+), 3 deletions(-) create mode 100644 arch/arm/include/asm/arch-at91/atmel_usba_udc.h create mode 100644 drivers/usb/gadget/atmel_usba_udc.c create mode 100644 drivers/usb/gadget/atmel_usba_udc.h create mode 100644 include/linux/usb/atmel_usba_udc.h -- 1.7.9.5

2 5

[U-Boot] [PATCH V2 0/5] EXYNOS: I2S: Enable I2S0 channel
by Dani Krishna Mohan 11 Sep '13

11 Sep '13

This patch set adds I2S-0 support and retains I2S-1 support. The default i2s channel can be selected through DT. Changes in V2: - Enabled I2S-0 support through DT - Retained I2S-1 support Changes in V1: - Added I2S-0 support - Removed I2S-1 support Dani Krishna Mohan (5): Sound: WM8994: Support I2S0 channel DTS: Addition of I2S0 channel and replacing I2S1 ARM: Added I2S0 clocks for audio Sound: I2S: Replacing I2S1 with I2S0 channel. Sound: MAX98095: Support I2S0 channel arch/arm/cpu/armv7/exynos/clock.c | 57 ++++++--- arch/arm/cpu/armv7/exynos/pinmux.c | 15 ++- arch/arm/dts/exynos5250.dtsi | 19 +++ arch/arm/include/asm/arch-exynos/clk.h | 5 +- arch/arm/include/asm/arch-exynos/clock.h | 4 + arch/arm/include/asm/arch-exynos/cpu.h | 4 + arch/arm/include/asm/arch-exynos/i2s-regs.h | 6 + arch/arm/include/asm/arch-exynos/periph.h | 1 + board/samsung/dts/exynos5250-smdk5250.dts | 13 +-- board/samsung/dts/exynos5250-snow.dts | 14 +-- drivers/sound/max98095.c | 128 ++++++++++++-------- drivers/sound/max98095.h | 10 +- drivers/sound/samsung-i2s.c | 52 ++++++--- drivers/sound/sound.c | 28 +++-- drivers/sound/wm8994.c | 167 +++++++++++++++++++-------- drivers/sound/wm8994_registers.h | 39 ++++++- include/i2s.h | 1 + 17 files changed, 403 insertions(+), 160 deletions(-) -- 1.7.9.5

3 7

[U-Boot] [PATCH v2 0/3] USB: atmel: add atmel usba udc driver support
by Bo Shen 11 Sep '13

11 Sep '13

Add atmel usb udc driver support porting from Linux kernel. Using RNDIS gadget driver to test it. Test OK on at91sam9m10g45ek, at91sam9m10g45ek, and sama5d31ek boards. It need the patch from: Troy Kisky <troy.kisky(a)boundarydevices.com> (usb: gadget: config: fix unaligned access issues) more information: http://patchwork.ozlabs.org/patch/264151/ Changes in v2: - Add detail information of the orignal code - Add a common header to hold atmel usba udc information for different SoCs Bo Shen (3): USB: gadget: add atmel usba udc driver ARM: atmel: correct UDPHS name ARM: atmel: add RNDIS gadget support arch/arm/cpu/armv7/at91/sama5d3_devices.c | 12 + arch/arm/include/asm/arch-at91/at91_common.h | 1 + arch/arm/include/asm/arch-at91/atmel_usba_udc.h | 64 ++ arch/arm/include/asm/arch-at91/sama5d3.h | 2 +- board/atmel/sama5d3xek/sama5d3xek.c | 13 + drivers/usb/gadget/Makefile | 1 + drivers/usb/gadget/atmel_usba_udc.c | 1305 +++++++++++++++++++++++ drivers/usb/gadget/atmel_usba_udc.h | 326 ++++++ include/configs/sama5d3xek.h | 8 + include/linux/usb/atmel_usba_udc.h | 26 + 10 files changed, 1757 insertions(+), 1 deletion(-) create mode 100644 arch/arm/include/asm/arch-at91/atmel_usba_udc.h create mode 100644 drivers/usb/gadget/atmel_usba_udc.c create mode 100644 drivers/usb/gadget/atmel_usba_udc.h create mode 100644 include/linux/usb/atmel_usba_udc.h -- 1.7.9.5

2 9

[U-Boot] [PATCH v7 0/2] apf27: add support of armadeus apf27
by Philippe Reynes 11 Sep '13

11 Sep '13

Difference between v7 and v6: - first patch "mx27: add missing constant for mx27" already accepted - remove useless variables regs - remove useless i2c initialization (already done in board_f.c) - remove CONFIG_I2C_MULTI_BUS (not used) - update u-boot filename in u-boot env - fix a typo in a comment in apf27.h Difference between v6 and v5: - use generic board framework - add fpga name Difference between v5 and v4: - use spl framework - use script - use SPDX-License-Identifier - use u-boot-with-spl.bin (instead of u-boot-nand.bin) - fix some comments format issue Difference between v4 and v3: - use standard start.S - use part to know u-boot offset - fix some comments format issue Difference between v3 and v2: - rebase on imx branch - merge support and spl patch - clean code of apf27_gpio_init - clean code of start.S Difference between v1 and v2: - use spl instead of nand_spl - use gpio api - remove use of useless CONFIG_SYS - remove use of config.mk - remove dead code Philippe Reynes (2): apf27: add support for the armadeus APF27 board apf27: add FPGA support for the apf27 board MAINTAINERS | 5 + board/armadeus/apf27/Makefile | 33 +++ board/armadeus/apf27/apf27.c | 256 ++++++++++++++++++ board/armadeus/apf27/apf27.h | 489 ++++++++++++++++++++++++++++++++++ board/armadeus/apf27/fpga.c | 224 ++++++++++++++++ board/armadeus/apf27/fpga.h | 25 ++ board/armadeus/apf27/lowlevel_init.S | 168 ++++++++++++ boards.cfg | 1 + include/configs/apf27.h | 388 +++++++++++++++++++++++++++ 9 files changed, 1589 insertions(+), 0 deletions(-) create mode 100644 board/armadeus/apf27/Makefile create mode 100644 board/armadeus/apf27/apf27.c create mode 100644 board/armadeus/apf27/apf27.h create mode 100644 board/armadeus/apf27/fpga.c create mode 100644 board/armadeus/apf27/fpga.h create mode 100644 board/armadeus/apf27/lowlevel_init.S create mode 100644 include/configs/apf27.h -- 1.7.4.4

2 4

[U-Boot] [PATCH] Subject: [PATCH v.2] at91: add support for CDU9G25 board
by Jiri Prchal 11 Sep '13

11 Sep '13

This patch adds support for our companies board CDU9G25 with Atmel AT91SAM9G25, 128MB DDR2, 256MB NAND. v.2 Fixed static IP and MAC addr cofiguration by random MAC and DHCP. Added entry to MAINTAINERS. Fixed line lenght, trailing spaces and other cosmetics. Signed-off-by: Jiri Prchal <jiri.prchal(a)aksignal.cz> --- MAINTAINERS | 3 + board/cdu9g25/Makefile | 48 +++++++++++ board/cdu9g25/cdu9g25.c | 134 +++++++++++++++++++++++++++++ board/cdu9g25/config.mk | 1 + boards.cfg | 1 + include/configs/cdu9g25.h | 204 +++++++++++++++++++++++++++++++++++++++++++++ 6 files changed, 391 insertions(+) create mode 100644 board/cdu9g25/Makefile create mode 100644 board/cdu9g25/cdu9g25.c create mode 100644 board/cdu9g25/config.mk create mode 100644 include/configs/cdu9g25.h diff --git a/MAINTAINERS b/MAINTAINERS index bd0f3a0..444500b 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -939,6 +939,9 @@ Bo Shen <voice.shen(a)atmel.com> at91sam9x5ek ARM926EJS (AT91SAM9G15,G25,G35,X25,X35 SoC) sama5d3xek ARMV7 (SAMA5D31, D33, D34, D35 SoC) +Jiri Prchal <jiri.prchal(a)aksignal.cz> + cdu9g25 ARM926EJS (AT91SAM9G25 SoC) + Rajeshwari Shinde <rajeshwari.s(a)samsung.com> snow ARM ARMV7 (EXYNOS5250 SoC) diff --git a/board/cdu9g25/Makefile b/board/cdu9g25/Makefile new file mode 100644 index 0000000..11e2d4f --- /dev/null +++ b/board/cdu9g25/Makefile @@ -0,0 +1,48 @@ +# +# (C) Copyright 2003-2008 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# (C) Copyright 2008 +# Stelian Pop <stelian(a)popies.net> +# Lead Tech Design <www.leadtechdesign.com> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += cdu9g25.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/cdu9g25/cdu9g25.c b/board/cdu9g25/cdu9g25.c new file mode 100644 index 0000000..e9cdbc3 --- /dev/null +++ b/board/cdu9g25/cdu9g25.c @@ -0,0 +1,134 @@ +/* + * (C) Copyright 2013 + * Jiri Prchal <jiri.prchal(a)aksignal.cz> + * AK signal <www.aksignal.cz> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/at91sam9x5_matrix.h> +#include <asm/arch/at91sam9_smc.h> +#include <asm/arch/at91_common.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_rstc.h> +#include <asm/arch/gpio.h> +#include <asm/arch/clk.h> +#include <atmel_hlcdc.h> +#include <atmel_mci.h> + +#ifdef CONFIG_MACB +#include <net.h> +#endif + +#include <netdev.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* ------------------------------------------------------------------------- */ +/* + * Miscelaneous platform dependent initialisations + */ + +#ifdef CONFIG_CMD_NAND +static void cdu9g25_nand_hw_init(void) +{ + struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; + struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + unsigned long csa; + + /* Enable CS3 */ + csa = readl(&matrix->ebicsa); + csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA; + writel(csa, &matrix->ebicsa); + + /* Configure SMC CS3 for NAND/SmartMedia */ + writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[3].setup); + writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) | + AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(6), + &smc->cs[3].pulse); + writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(6), + &smc->cs[3].cycle); + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | + AT91_SMC_MODE_DBW_8 | + AT91_SMC_MODE_TDF_CYCLE(1), + &smc->cs[3].mode); + + writel(1 << ATMEL_ID_PIOCD, &pmc->pcer); + + /* Configure RDY/BSY */ + at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); + + /* Enable NandFlash */ + at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); + + at91_set_a_periph(AT91_PIO_PORTD, 0, 1); /* NAND OE */ + at91_set_a_periph(AT91_PIO_PORTD, 1, 1); /* NAND WE */ + at91_set_a_periph(AT91_PIO_PORTD, 2, 1); /* NAND ALE */ + at91_set_a_periph(AT91_PIO_PORTD, 3, 1); /* NAND CLE */ +} +#endif + +int board_eth_init(bd_t *bis) +{ + int rc = 0; + uchar enetaddr[6]; + + eth_random_enetaddr(enetaddr); + eth_setenv_enetaddr("ethaddr", enetaddr); + +#ifdef CONFIG_MACB + rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x00); +#endif + return rc; +} + +static void cdu9g25_led_init(void) +{ + at91_set_gpio_output(CONFIG_LED_B, 1); + at91_set_gpio_value(CONFIG_LED_B, 0); +} + +int board_early_init_f(void) +{ + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + + at91_seriald_hw_init(); + return 0; +} + +int board_init(void) +{ + /* arch number of AT91SAM9X5EK-Board */ + gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9X5EK; + + /* adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + + cdu9g25_led_init(); + + cdu9g25_nand_hw_init(); + + at91_macb_hw_init(); + + return 0; +} + +int dram_init(void) +{ + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, + CONFIG_SYS_SDRAM_SIZE); + return 0; +} + +#ifdef CONFIG_RESET_PHY_R +void reset_phy(void) +{ +} +#endif + diff --git a/board/cdu9g25/config.mk b/board/cdu9g25/config.mk new file mode 100644 index 0000000..528ed4a --- /dev/null +++ b/board/cdu9g25/config.mk @@ -0,0 +1 @@ +CONFIG_SYS_TEXT_BASE = 0x27f00000 diff --git a/boards.cfg b/boards.cfg index be810c7..572d20d 100644 --- a/boards.cfg +++ b/boards.cfg @@ -77,6 +77,7 @@ integratorcp_cm926ejs arm arm926ejs integrator armltd aspenite arm arm926ejs - Marvell armada100 gplugd arm arm926ejs - Marvell armada100 afeb9260 arm arm926ejs - - at91 +cdu9g25 arm arm926ejs - - at91 at91sam9260ek_dataflash_cs0 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9260,SYS_USE_DATAFLASH_CS0 at91sam9260ek_dataflash_cs1 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9260,SYS_USE_DATAFLASH_CS1 at91sam9260ek_nandflash arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9260,SYS_USE_NANDFLASH diff --git a/include/configs/cdu9g25.h b/include/configs/cdu9g25.h new file mode 100644 index 0000000..9324de5 --- /dev/null +++ b/include/configs/cdu9g25.h @@ -0,0 +1,204 @@ +/* + * (C) Copyright 2013 + * Jiri Prchal <jiri.prchal(a)aksignal.cz> + * AK signal <www.aksignal.cz> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H__ +#define __CONFIG_H__ + +#define CONFIG_AT91SAM9X5 +#include <asm/hardware.h> + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ +#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* main clock xtal */ +#define CONFIG_SYS_HZ 1000 + +/* Define actual evaluation board type from used processor type */ +#define CONFIG_CDU9G25 +#define CONFIG_AT91FAMILY + +/* Misc CPU related */ +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_DISPLAY_CPUINFO + +#define CONFIG_CMD_BOOTZ +#define CONFIG_OF_LIBFDT + +/* general purpose I/O */ +#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ +#define CONFIG_AT91_GPIO +#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */ + +/* LEDs */ +#define CONFIG_LED_R AT91_PIN_PB18 +#define CONFIG_LED_G AT91_PIN_PB16 +#define CONFIG_LED_Y AT91_PIN_PB14 +#define CONFIG_LED_B AT91_PIN_PB12 + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_SYS +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 } + +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_HW_WATCHDOG +#define CONFIG_AT91SAM9_WATCHDOG + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_LOADS + +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NAND +#define CONFIG_CMD_MMC +#define CONFIG_CMD_FAT + +/* + * SDRAM: 1 bank, min 32, max 128 MB + * Initialized before u-boot gets started. + */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE 0x20000000 /* ATMEL_BASE_CS1 */ +#define CONFIG_SYS_SDRAM_SIZE 0x08000000 + +/* + * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM, + * leaving the correct space for initial global data structure above + * that address while providing maximum stack area below. + */ +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 4 * 1024\ + - GENERATED_GBL_DATA_SIZE) + +/* no NOR flash */ +#define CONFIG_SYS_NO_FLASH + +/* NAND flash */ +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE 0x40000000 +#define CONFIG_SYS_NAND_DBW_8 1 +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PD4 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PD5 + +/* PMECC & PMERRLOC */ +#define CONFIG_ATMEL_NAND_HWECC 1 +#define CONFIG_ATMEL_NAND_HW_PMECC 1 +#define CONFIG_PMECC_CAP 8 +#define CONFIG_PMECC_SECTOR_SIZE 512 +#define CONFIG_PMECC_INDEX_TABLE_OFFSET 0x8000 + +#define CONFIG_MTD_DEVICE +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_PARTITIONS +#define CONFIG_RBTREE +#define CONFIG_LZO +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS +#define CONFIG_CMD_NAND_TRIMFFS +#define MTDIDS_DEFAULT "nand0=nand" +#define MTDPARTS_DEFAULT "mtdparts=nand:256k(bootstrap),"\ + "768k(uboot),256k(ubootenv),"\ + "4864k(kernel),"\ + "-(root)" + +/* MMC */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_GENERIC_ATMEL_MCI +#endif + +/* FAT */ +#ifdef CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* Ethernet */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_MACB_SEARCH_PHY +#define CONFIG_RANDOM_MACADDR + +/* USB */ +#ifdef CONFIG_CMD_USB +#ifdef CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_ATMEL +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2 +#else +#define CONFIG_USB_OHCI_NEW +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9x5" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3 +#endif +#define CONFIG_USB_ATMEL +#define CONFIG_USB_STORAGE +#endif + +#define CONFIG_SYS_LOAD_ADDR 0x21000000 /* load address */ + +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_TEXT_BASE + +/* CONFIG_SYS_USE_NANDFLASH */ +/* bootstrap + u-boot + env + linux in nandflash */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x100000 +#define CONFIG_ENV_SIZE 0x20000 /* 2 sectors = 256kB */ +#define CONFIG_BOOTCOMMAND "nand read 21000000 kernel; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 ubi.mtd=root"\ + "root=ubi0:root rootfstype=ubifs rw"\ + "g_ether.dev_addr=02:04:25:aa:55:5e"\ + "g_ether.host_addr=02:04:25:aa:55:5f" +#define CONFIG_SERVERIP 10.0.1.1 +#define CONFIG_BOOTFILE "kernel_cdu9g25" +#define CONFIG_PREBOOT "mtdparts default" /* for partitions */ + +#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)\ + + 16) +#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024 + 0x1000) + +#ifdef CONFIG_USE_IRQ +#error CONFIG_USE_IRQ not supported +#endif + +#endif -- 1.7.9.5

4 5