September 2013 - U-Boot

[U-Boot] [RFC 00/10] New board-specific USB initialization interface
by Mateusz Zalega 08 Oct '13

08 Oct '13

Current implementation of do_dfu() and do_usb_mass_storage() requires board-specific board_usb_init() which performs USB hardware initialization. I noticed that several boards have such a function defined, named either usb_board_init() (which binds to ohci-hcd.c driver and had been used solely by it) or board_usb_init() (as in ehci-omap.c). I _assumed_ that these functions do what's required by do_*() and renamed the earlier in order to unify the naming convention. It would: + make enabling DFU and UMS in these boards easier + clean up the namespace + improve code reusability + enable devs to postpone hardware init until it's needed (as in do_dfu()) Declarations of these functions were scattered all over the codebase. Seeing it as a bad practice, I added declaration of usb_board_init() in usb.h and removed the other. I added a weak symbol for usb_board_init() in usb.c so that boards which do not require USB initialization or have to initialize hardware earlier would compile and run. For boards which offer both USB device and host capabilities, you can specify which part, host or device, to initialize, via function argument. Does this approach sound good and/or reasonable? Code compiles successfully for all ARM boards and was tested on Samsung Goni. Mateusz Zalega (10): New board-specific USB initialization interface nvidia, tegra: new USB hardware init interface Voipac PXA270: new USB hardware init interface Trizeps IV: new USB hardware init interface Colibri PXA270: new USB hardware init interface icpdas lp8x4x: new USB hardware init interface esd pmc440: new USB hardware init interface esd apc405: new USB hardware init interface balloon3: new USB hardware init interface canyonlands: new USB hardware init interface arch/arm/include/asm/arch-tegra/usb.h | 3 +-- board/amcc/canyonlands/canyonlands.c | 5 +++-- board/balloon3/balloon3.c | 5 +++-- board/esd/apc405/apc405.c | 5 +++-- board/esd/pmc440/pmc440.c | 5 +++-- board/icpdas/lp8x4x/lp8x4x.c | 5 +++-- board/nvidia/common/board.c | 14 ++++++++++---- board/toradex/colibri_pxa270/colibri_pxa270.c | 5 +++-- board/trizepsiv/conxs.c | 5 +++-- board/vpac270/vpac270.c | 5 +++-- common/cmd_dfu.c | 5 ++--- common/cmd_usb_mass_storage.c | 3 ++- common/usb.c | 5 +++++ drivers/usb/host/ehci-omap.c | 8 +------- drivers/usb/host/ehci-tegra.c | 2 +- drivers/usb/host/ohci-hcd.c | 4 ++-- drivers/usb/host/ohci.h | 12 +++++------- include/g_dnl.h | 2 -- include/usb.h | 17 ++++++++++++++++- include/usb_mass_storage.h | 12 +++++------- 20 files changed, 74 insertions(+), 53 deletions(-) -- 1.8.2.1

7 62

[U-Boot] [PATCH] Enable the DIU for P1022DS board.
by Jason Jin 08 Oct '13

08 Oct '13

The DIU of P1022DS was disabled by commit: dfe64e2c89731a3f9950d7acd8681b68df2bae03 to verify the u-boot MTD subsystem. The local bus and DIU is multiplex on P1022, but the DIU will not be enabled if there is no video-mode environment. The NAND still can be used with DIU enabled in the configuration file with the video-mode environment disabled. Signed-off-by: Jason Jin <Jason.Jin(a)freescale.com> --- include/configs/P1022DS.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index edece1f..f3f4c30 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -413,6 +413,7 @@ #define CONFIG_SYS_HUSH_PARSER /* Video */ +#define CONFIG_FSL_DIU_FB #ifdef CONFIG_FSL_DIU_FB #define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x10000) @@ -432,6 +433,7 @@ #endif #ifndef CONFIG_FSL_DIU_FB +#define CONFIG_ATI #endif #ifdef CONFIG_ATI -- 1.8.0

3 2

[U-Boot] [PATCH] power:pmic: prevent data abort for pmic bat command
by Piotr Wilczek 07 Oct '13

07 Oct '13

This patch prevents data abort when pmic bat command is called on non-batery pmic device. Signed-off-by: Piotr Wilczek <p.wilczek(a)samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park(a)samsung.com> CC: Lukasz Majewski <l.majewski(a)samsung.com> CC: Minkyu Kang <mk7.kang(a)samsung.com> --- drivers/power/power_core.c | 19 +++++++++++-------- 1 file changed, 11 insertions(+), 8 deletions(-) diff --git a/drivers/power/power_core.c b/drivers/power/power_core.c index 583e56b..d9bc05f 100644 --- a/drivers/power/power_core.c +++ b/drivers/power/power_core.c @@ -188,18 +188,21 @@ int do_pmic(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) if (argc < 4) return CMD_RET_USAGE; + if (!p->pbat) { + printf("%s is not a battery\n", p->name); + return CMD_RET_FAILURE; + } + if (strcmp(argv[3], "state") == 0) p->fg->fg_battery_check(p->pbat->fg, p); if (strcmp(argv[3], "charge") == 0) { - if (p->pbat) { - printf("BAT: %s charging (ctrl+c to break)\n", - p->name); - if (p->low_power_mode) - p->low_power_mode(); - if (p->pbat->battery_charge) - p->pbat->battery_charge(p); - } + printf("BAT: %s charging (ctrl+c to break)\n", + p->name); + if (p->low_power_mode) + p->low_power_mode(); + if (p->pbat->battery_charge) + p->pbat->battery_charge(p); } return CMD_RET_SUCCESS; -- 1.7.9.5

2 1

[U-Boot] [PATCH] pci: Properly configure prefetchable memory region
by Thierry Reding 07 Oct '13

07 Oct '13

Forcibly set hose->pci_prefetch to NULL to make sure it will be setup. This will help if for any reason callers didn't make sure themselves to NULL the field. Signed-off-by: Thierry Reding <treding(a)nvidia.com> --- drivers/pci/pci_auto.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/pci/pci_auto.c b/drivers/pci/pci_auto.c index c4ed8ba..86ba6b5 100644 --- a/drivers/pci/pci_auto.c +++ b/drivers/pci/pci_auto.c @@ -297,7 +297,7 @@ void pciauto_config_init(struct pci_controller *hose) { int i; - hose->pci_io = hose->pci_mem = NULL; + hose->pci_io = hose->pci_mem = hose->pci_prefetch = NULL; for (i = 0; i < hose->region_count; i++) { switch(hose->regions[i].flags) { -- 1.8.4

2 1

[U-Boot] [RESEND PATCH v6 2/2] socfpga: Adding pin mux handoff files
by Chin Liang See 07 Oct '13

07 Oct '13

Adding the generated pin mux configuration by Preloader Generator tool Signed-off-by: Chin Liang See <clsee(a)altera.com> Reviewed-by: Pavel Machek <pavel(a)denx.de> Acked-by: Dinh Nguyen <dinguyen(a)altera.com> Cc: Wolfgang Denk <wd(a)denx.de> CC: Pavel Machek <pavel(a)denx.de> Cc: Dinh Nguyen <dinguyen(a)altera.com> Cc: Tom Rini <trini(a)ti.com> Cc: Albert Aribaud <albert.u.boot(a)aribaud.net> --- Changes for v6: - Re-shuffle the change list Changes for v5: - Updated the subject Changes for v4: - Added change log for each revision change Changes for v3: - Fixed the long subject of the patch Changes for v2: - Fixed the word wrap issue within patch --- board/altera/socfpga/pinmux_config.c | 214 ++++++++++++++++++++++++++++++++++ board/altera/socfpga/pinmux_config.h | 54 +++++++++ 2 files changed, 268 insertions(+) create mode 100644 board/altera/socfpga/pinmux_config.c create mode 100644 board/altera/socfpga/pinmux_config.h diff --git a/board/altera/socfpga/pinmux_config.c b/board/altera/socfpga/pinmux_config.c new file mode 100644 index 0000000..8b09005 --- /dev/null +++ b/board/altera/socfpga/pinmux_config.c @@ -0,0 +1,214 @@ +/* This file is generated by Preloader Generator */ + +#include "pinmux_config.h" + +/* pin mux configuration data */ +unsigned long sys_mgr_init_table[CONFIG_HPS_PINMUX_NUM] = { + 0, /* EMACIO0 - Unused */ + 2, /* EMACIO1 - USB */ + 2, /* EMACIO2 - USB */ + 2, /* EMACIO3 - USB */ + 2, /* EMACIO4 - USB */ + 2, /* EMACIO5 - USB */ + 2, /* EMACIO6 - USB */ + 2, /* EMACIO7 - USB */ + 2, /* EMACIO8 - USB */ + 0, /* EMACIO9 - Unused */ + 2, /* EMACIO10 - USB */ + 2, /* EMACIO11 - USB */ + 2, /* EMACIO12 - USB */ + 2, /* EMACIO13 - USB */ + 0, /* EMACIO14 - N/A */ + 0, /* EMACIO15 - N/A */ + 0, /* EMACIO16 - N/A */ + 0, /* EMACIO17 - N/A */ + 0, /* EMACIO18 - N/A */ + 0, /* EMACIO19 - N/A */ + 3, /* FLASHIO0 - SDMMC */ + 3, /* FLASHIO1 - SDMMC */ + 3, /* FLASHIO2 - SDMMC */ + 3, /* FLASHIO3 - SDMMC */ + 0, /* FLASHIO4 - SDMMC */ + 0, /* FLASHIO5 - SDMMC */ + 0, /* FLASHIO6 - SDMMC */ + 0, /* FLASHIO7 - SDMMC */ + 0, /* FLASHIO8 - SDMMC */ + 3, /* FLASHIO9 - SDMMC */ + 3, /* FLASHIO10 - SDMMC */ + 3, /* FLASHIO11 - SDMMC */ + 3, /* GENERALIO0 - TRACE */ + 3, /* GENERALIO1 - TRACE */ + 3, /* GENERALIO2 - TRACE */ + 3, /* GENERALIO3 - TRACE */ + 3, /* GENERALIO4 - TRACE */ + 3, /* GENERALIO5 - TRACE */ + 3, /* GENERALIO6 - TRACE */ + 3, /* GENERALIO7 - TRACE */ + 3, /* GENERALIO8 - TRACE */ + 3, /* GENERALIO9 - SPIM0 */ + 3, /* GENERALIO10 - SPIM0 */ + 3, /* GENERALIO11 - SPIM0 */ + 3, /* GENERALIO12 - SPIM0 */ + 2, /* GENERALIO13 - CAN0 */ + 2, /* GENERALIO14 - CAN0 */ + 3, /* GENERALIO15 - I2C0 */ + 3, /* GENERALIO16 - I2C0 */ + 2, /* GENERALIO17 - UART0 */ + 2, /* GENERALIO18 - UART0 */ + 0, /* GENERALIO19 - N/A */ + 0, /* GENERALIO20 - N/A */ + 0, /* GENERALIO21 - N/A */ + 0, /* GENERALIO22 - N/A */ + 0, /* GENERALIO23 - N/A */ + 0, /* GENERALIO24 - N/A */ + 0, /* GENERALIO25 - N/A */ + 0, /* GENERALIO26 - N/A */ + 0, /* GENERALIO27 - N/A */ + 0, /* GENERALIO28 - N/A */ + 0, /* GENERALIO29 - N/A */ + 0, /* GENERALIO30 - N/A */ + 0, /* GENERALIO31 - N/A */ + 2, /* MIXED1IO0 - EMAC */ + 2, /* MIXED1IO1 - EMAC */ + 2, /* MIXED1IO2 - EMAC */ + 2, /* MIXED1IO3 - EMAC */ + 2, /* MIXED1IO4 - EMAC */ + 2, /* MIXED1IO5 - EMAC */ + 2, /* MIXED1IO6 - EMAC */ + 2, /* MIXED1IO7 - EMAC */ + 2, /* MIXED1IO8 - EMAC */ + 2, /* MIXED1IO9 - EMAC */ + 2, /* MIXED1IO10 - EMAC */ + 2, /* MIXED1IO11 - EMAC */ + 2, /* MIXED1IO12 - EMAC */ + 2, /* MIXED1IO13 - EMAC */ + 0, /* MIXED1IO14 - Unused */ + 3, /* MIXED1IO15 - QSPI */ + 3, /* MIXED1IO16 - QSPI */ + 3, /* MIXED1IO17 - QSPI */ + 3, /* MIXED1IO18 - QSPI */ + 3, /* MIXED1IO19 - QSPI */ + 3, /* MIXED1IO20 - QSPI */ + 0, /* MIXED1IO21 - GPIO */ + 0, /* MIXED2IO0 - N/A */ + 0, /* MIXED2IO1 - N/A */ + 0, /* MIXED2IO2 - N/A */ + 0, /* MIXED2IO3 - N/A */ + 0, /* MIXED2IO4 - N/A */ + 0, /* MIXED2IO5 - N/A */ + 0, /* MIXED2IO6 - N/A */ + 0, /* MIXED2IO7 - N/A */ + 0, /* GPLINMUX48 */ + 0, /* GPLINMUX49 */ + 0, /* GPLINMUX50 */ + 0, /* GPLINMUX51 */ + 0, /* GPLINMUX52 */ + 0, /* GPLINMUX53 */ + 0, /* GPLINMUX54 */ + 0, /* GPLINMUX55 */ + 0, /* GPLINMUX56 */ + 0, /* GPLINMUX57 */ + 0, /* GPLINMUX58 */ + 0, /* GPLINMUX59 */ + 0, /* GPLINMUX60 */ + 0, /* GPLINMUX61 */ + 0, /* GPLINMUX62 */ + 0, /* GPLINMUX63 */ + 0, /* GPLINMUX64 */ + 0, /* GPLINMUX65 */ + 0, /* GPLINMUX66 */ + 0, /* GPLINMUX67 */ + 0, /* GPLINMUX68 */ + 0, /* GPLINMUX69 */ + 0, /* GPLINMUX70 */ + 1, /* GPLMUX0 */ + 1, /* GPLMUX1 */ + 1, /* GPLMUX2 */ + 1, /* GPLMUX3 */ + 1, /* GPLMUX4 */ + 1, /* GPLMUX5 */ + 1, /* GPLMUX6 */ + 1, /* GPLMUX7 */ + 1, /* GPLMUX8 */ + 1, /* GPLMUX9 */ + 1, /* GPLMUX10 */ + 1, /* GPLMUX11 */ + 1, /* GPLMUX12 */ + 1, /* GPLMUX13 */ + 1, /* GPLMUX14 */ + 1, /* GPLMUX15 */ + 1, /* GPLMUX16 */ + 1, /* GPLMUX17 */ + 1, /* GPLMUX18 */ + 1, /* GPLMUX19 */ + 1, /* GPLMUX20 */ + 1, /* GPLMUX21 */ + 1, /* GPLMUX22 */ + 1, /* GPLMUX23 */ + 1, /* GPLMUX24 */ + 1, /* GPLMUX25 */ + 1, /* GPLMUX26 */ + 1, /* GPLMUX27 */ + 1, /* GPLMUX28 */ + 1, /* GPLMUX29 */ + 1, /* GPLMUX30 */ + 1, /* GPLMUX31 */ + 1, /* GPLMUX32 */ + 1, /* GPLMUX33 */ + 1, /* GPLMUX34 */ + 1, /* GPLMUX35 */ + 1, /* GPLMUX36 */ + 1, /* GPLMUX37 */ + 1, /* GPLMUX38 */ + 1, /* GPLMUX39 */ + 1, /* GPLMUX40 */ + 1, /* GPLMUX41 */ + 1, /* GPLMUX42 */ + 1, /* GPLMUX43 */ + 1, /* GPLMUX44 */ + 1, /* GPLMUX45 */ + 1, /* GPLMUX46 */ + 1, /* GPLMUX47 */ + 1, /* GPLMUX48 */ + 1, /* GPLMUX49 */ + 1, /* GPLMUX50 */ + 1, /* GPLMUX51 */ + 1, /* GPLMUX52 */ + 1, /* GPLMUX53 */ + 1, /* GPLMUX54 */ + 1, /* GPLMUX55 */ + 1, /* GPLMUX56 */ + 1, /* GPLMUX57 */ + 1, /* GPLMUX58 */ + 1, /* GPLMUX59 */ + 1, /* GPLMUX60 */ + 1, /* GPLMUX61 */ + 1, /* GPLMUX62 */ + 1, /* GPLMUX63 */ + 1, /* GPLMUX64 */ + 1, /* GPLMUX65 */ + 1, /* GPLMUX66 */ + 1, /* GPLMUX67 */ + 1, /* GPLMUX68 */ + 1, /* GPLMUX69 */ + 1, /* GPLMUX70 */ + 0, /* NANDUSEFPGA */ + 0, /* UART0USEFPGA */ + 0, /* RGMII1USEFPGA */ + 0, /* SPIS0USEFPGA */ + 0, /* CAN0USEFPGA */ + 0, /* I2C0USEFPGA */ + 0, /* SDMMCUSEFPGA */ + 0, /* QSPIUSEFPGA */ + 0, /* SPIS1USEFPGA */ + 0, /* RGMII0USEFPGA */ + 0, /* UART1USEFPGA */ + 0, /* CAN1USEFPGA */ + 0, /* USB1USEFPGA */ + 0, /* I2C3USEFPGA */ + 0, /* I2C2USEFPGA */ + 0, /* I2C1USEFPGA */ + 0, /* SPIM1USEFPGA */ + 0, /* USB0USEFPGA */ + 0 /* SPIM0USEFPGA */ +}; diff --git a/board/altera/socfpga/pinmux_config.h b/board/altera/socfpga/pinmux_config.h new file mode 100644 index 0000000..f278f2b --- /dev/null +++ b/board/altera/socfpga/pinmux_config.h @@ -0,0 +1,54 @@ +/* This file is generated by Preloader Generator */ + +#ifndef _PRELOADER_PINMUX_CONFIG_H_ +#define _PRELOADER_PINMUX_CONFIG_H_ + +/* + * State of enabling for which IP connected out through the muxing. + * Value 1 mean the IP connection is muxed out + */ +#define CONFIG_HPS_EMAC0 (0) +#define CONFIG_HPS_EMAC1 (1) +#define CONFIG_HPS_USB0 (0) +#define CONFIG_HPS_USB1 (1) +#define CONFIG_HPS_NAND (0) +#define CONFIG_HPS_SDMMC (1) +#define CONFIG_HPS_QSPI (1) +#define CONFIG_HPS_UART0 (1) +#define CONFIG_HPS_UART1 (0) +#define CONFIG_HPS_TRACE (1) +#define CONFIG_HPS_I2C0 (1) +#define CONFIG_HPS_I2C1 (0) +#define CONFIG_HPS_I2C2 (0) +#define CONFIG_HPS_I2C3 (0) +#define CONFIG_HPS_SPIM0 (1) +#define CONFIG_HPS_SPIM1 (0) +#define CONFIG_HPS_SPIS0 (0) +#define CONFIG_HPS_SPIS1 (0) +#define CONFIG_HPS_CAN0 (1) +#define CONFIG_HPS_CAN1 (0) + +/* IP attribute value (which affected by pin muxing configuration) */ +#define CONFIG_HPS_SDMMC_BUSWIDTH (4) + +/* 1 if the pins are connected out */ +#define CONFIG_HPS_QSPI_CS0 (1) +#define CONFIG_HPS_QSPI_CS1 (0) +#define CONFIG_HPS_QSPI_CS2 (0) +#define CONFIG_HPS_QSPI_CS3 (0) + +/* UART */ +/* 1 means the pin is mux out or available */ +#define CONFIG_HPS_UART0_TX (1) +#define CONFIG_HPS_UART0_RX (1) +#define CONFIG_HPS_UART0_CTS (0) +#define CONFIG_HPS_UART0_RTS (0) +#define CONFIG_HPS_UART1_TX (0) +#define CONFIG_HPS_UART1_RX (0) +#define CONFIG_HPS_UART1_CTS (0) +#define CONFIG_HPS_UART1_RTS (0) + +/* Pin mux data */ +#define CONFIG_HPS_PINMUX_NUM (207) + +#endif /* _PRELOADER_PINMUX_CONFIG_H_ */ -- 1.7.9.5

2 2

[U-Boot] [RESEND PATCH v7 1/2] socfpga: Adding System Manager driver
by Chin Liang See 07 Oct '13

07 Oct '13

Adding System Manager driver which will configure the pin mux for real hardware Cyclone V development kit (not Virtual Platform) Signed-off-by: Chin Liang See <clsee(a)altera.com> Reviewed-by: Pavel Machek <pavel(a)denx.de> Acked-by: Dinh Nguyen <dinguyen(a)altera.com> Cc: Wolfgang Denk <wd(a)denx.de> CC: Pavel Machek <pavel(a)denx.de> Cc: Dinh Nguyen <dinguyen(a)altera.com> Cc: Tom Rini <trini(a)ti.com> Cc: Albert Aribaud <albert.u.boot(a)aribaud.net> --- Changes for v7: - Re-shuffle the change list Changes for v6: - Updated the license header for system_manager.c and .h to SPDX Changes for v5: - Updated the license header for system_manager.c - Cc: Tom Rini Changes for v4: - Added change log for each revision change Changes for v3: - Fixed the long subject of the patch - Fixed the comment within the code Changes for v2: - Fixed the word wrap issue within patch --- arch/arm/cpu/armv7/socfpga/Makefile | 2 +- arch/arm/cpu/armv7/socfpga/spl.c | 6 ++++ arch/arm/cpu/armv7/socfpga/system_manager.c | 29 ++++++++++++++++++++ .../include/asm/arch-socfpga/socfpga_base_addrs.h | 1 + arch/arm/include/asm/arch-socfpga/system_manager.h | 22 +++++++++++++++ board/altera/socfpga/Makefile | 4 ++- include/configs/socfpga_cyclone5.h | 1 + 7 files changed, 63 insertions(+), 2 deletions(-) create mode 100644 arch/arm/cpu/armv7/socfpga/system_manager.c create mode 100644 arch/arm/include/asm/arch-socfpga/system_manager.h diff --git a/arch/arm/cpu/armv7/socfpga/Makefile b/arch/arm/cpu/armv7/socfpga/Makefile index 5024fc5..0859e44 100644 --- a/arch/arm/cpu/armv7/socfpga/Makefile +++ b/arch/arm/cpu/armv7/socfpga/Makefile @@ -13,7 +13,7 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(SOC).o SOBJS := lowlevel_init.o -COBJS-y := misc.o timer.o reset_manager.o +COBJS-y := misc.o timer.o reset_manager.o system_manager.o COBJS-$(CONFIG_SPL_BUILD) += spl.o COBJS := $(COBJS-y) diff --git a/arch/arm/cpu/armv7/socfpga/spl.c b/arch/arm/cpu/armv7/socfpga/spl.c index 2b9be28..74bceab 100644 --- a/arch/arm/cpu/armv7/socfpga/spl.c +++ b/arch/arm/cpu/armv7/socfpga/spl.c @@ -12,6 +12,7 @@ #include <image.h> #include <asm/arch/reset_manager.h> #include <spl.h> +#include <asm/arch/system_manager.h> DECLARE_GLOBAL_DATA_PTR; @@ -25,6 +26,11 @@ u32 spl_boot_device(void) */ void spl_board_init(void) { +#ifndef CONFIG_SOCFPGA_VIRTUAL_TARGET + /* configure the pin muxing through system manager */ + sysmgr_pinmux_init(); +#endif /* CONFIG_SOCFPGA_VIRTUAL_TARGET */ + /* de-assert reset for peripherals and bridges based on handoff */ reset_deassert_peripherals_handoff(); diff --git a/arch/arm/cpu/armv7/socfpga/system_manager.c b/arch/arm/cpu/armv7/socfpga/system_manager.c new file mode 100644 index 0000000..b992221 --- /dev/null +++ b/arch/arm/cpu/armv7/socfpga/system_manager.c @@ -0,0 +1,29 @@ +/* + * Copyright (C) 2013 Altera Corporation <www.altera.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/system_manager.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Configure all the pin muxes + */ +void sysmgr_pinmux_init(void) +{ + unsigned long offset = CONFIG_SYSMGR_PINMUXGRP_OFFSET; + + const unsigned long *pval = sys_mgr_init_table; + unsigned long i; + + for (i = 0; i < ARRAY_SIZE(sys_mgr_init_table); + i++, offset += sizeof(unsigned long)) { + writel(*pval++, (SOCFPGA_SYSMGR_ADDRESS + offset)); + } +} + + diff --git a/arch/arm/include/asm/arch-socfpga/socfpga_base_addrs.h b/arch/arm/include/asm/arch-socfpga/socfpga_base_addrs.h index 1182a13..50c4ebd 100644 --- a/arch/arm/include/asm/arch-socfpga/socfpga_base_addrs.h +++ b/arch/arm/include/asm/arch-socfpga/socfpga_base_addrs.h @@ -12,5 +12,6 @@ #define SOCFPGA_UART1_ADDRESS 0xffc03000 #define SOCFPGA_OSC1TIMER0_ADDRESS 0xffd00000 #define SOCFPGA_RSTMGR_ADDRESS 0xffd05000 +#define SOCFPGA_SYSMGR_ADDRESS 0xffd08000 #endif /* _SOCFPGA_BASE_ADDRS_H_ */ diff --git a/arch/arm/include/asm/arch-socfpga/system_manager.h b/arch/arm/include/asm/arch-socfpga/system_manager.h new file mode 100644 index 0000000..d965d25 --- /dev/null +++ b/arch/arm/include/asm/arch-socfpga/system_manager.h @@ -0,0 +1,22 @@ +/* + * Copyright (C) 2013 Altera Corporation <www.altera.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _SYSTEM_MANAGER_H_ +#define _SYSTEM_MANAGER_H_ + +#ifndef __ASSEMBLY__ + +void sysmgr_pinmux_init(void); + +/* declaration for handoff table type */ +extern unsigned long sys_mgr_init_table[CONFIG_HPS_PINMUX_NUM]; + +#endif + + +#define CONFIG_SYSMGR_PINMUXGRP_OFFSET (0x400) + +#endif /* _SYSTEM_MANAGER_H_ */ diff --git a/board/altera/socfpga/Makefile b/board/altera/socfpga/Makefile index 43bbc37..3092387 100644 --- a/board/altera/socfpga/Makefile +++ b/board/altera/socfpga/Makefile @@ -26,8 +26,10 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o -COBJS := socfpga_cyclone5.o +COBJS-y := socfpga_cyclone5.o +COBJS-$(CONFIG_SPL_BUILD) += pinmux_config.o +COBJS := $(COBJS-y) SRCS := $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) diff --git a/include/configs/socfpga_cyclone5.h b/include/configs/socfpga_cyclone5.h index 06aeba6..346ca72 100644 --- a/include/configs/socfpga_cyclone5.h +++ b/include/configs/socfpga_cyclone5.h @@ -7,6 +7,7 @@ #define __CONFIG_H #include <asm/arch/socfpga_base_addrs.h> +#include "../../board/altera/socfpga/pinmux_config.h" /* * High level configuration -- 1.7.9.5

2 2

[U-Boot] [PATCH] omap1510inn: arm925t: remove support
by Albert ARIBAUD 07 Oct '13

07 Oct '13

omap1510inn is orphan and has been for years now. Reove it and, as it was the only arm925t target, also remove arm925t support. Signed-off-by: Albert ARIBAUD <albert.u.boot(a)aribaud.net> --- MAINTAINERS | 2 - MAKEALL | 1 - README | 1 - arch/arm/cpu/arm925t/Makefile | 34 --- arch/arm/cpu/arm925t/config.mk | 17 -- arch/arm/cpu/arm925t/cpu.c | 50 ---- arch/arm/cpu/arm925t/omap925.c | 23 -- arch/arm/cpu/arm925t/start.S | 382 ------------------------------- arch/arm/cpu/arm925t/timer.c | 104 --------- board/ti/omap1510inn/Makefile | 29 --- board/ti/omap1510inn/config.mk | 25 -- board/ti/omap1510inn/lowlevel_init.S | 380 ------------------------------ board/ti/omap1510inn/omap1510innovator.c | 125 ---------- boards.cfg | 1 - include/arm925t.h | 11 - include/configs/omap1510inn.h | 166 -------------- 16 files changed, 1351 deletions(-) delete mode 100644 arch/arm/cpu/arm925t/Makefile delete mode 100644 arch/arm/cpu/arm925t/config.mk delete mode 100644 arch/arm/cpu/arm925t/cpu.c delete mode 100644 arch/arm/cpu/arm925t/omap925.c delete mode 100644 arch/arm/cpu/arm925t/start.S delete mode 100644 arch/arm/cpu/arm925t/timer.c delete mode 100644 board/ti/omap1510inn/Makefile delete mode 100644 board/ti/omap1510inn/config.mk delete mode 100644 board/ti/omap1510inn/lowlevel_init.S delete mode 100644 board/ti/omap1510inn/omap1510innovator.c delete mode 100644 include/arm925t.h delete mode 100644 include/configs/omap1510inn.h diff --git a/MAINTAINERS b/MAINTAINERS index 081cf96..49da125 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1088,8 +1088,6 @@ Unknown / orphaned boards: Board CPU Last known maintainer / Comment ......................................................................... - omap1510inn ARM925T Kshitij Gupta <kshitij(a)ti.com> - lubbock xscale/pxa Kyle Harris <kharris(a)nexus-tech.net> / dead address imx31_phycore_eet i.MX31 Guennadi Liakhovetski <g.liakhovetski(a)gmx.de> / resigned diff --git a/MAKEALL b/MAKEALL index bed99de..da89752 100755 --- a/MAKEALL +++ b/MAKEALL @@ -353,7 +353,6 @@ LIST_ARM7="$(boards_by_cpu arm720t)" LIST_ARM9="$(boards_by_cpu arm920t) \ $(boards_by_cpu arm926ejs) \ - $(boards_by_cpu arm925t) \ $(boards_by_cpu arm946es) \ " diff --git a/README b/README index a5c3e8d..b9ed3df 100644 --- a/README +++ b/README @@ -139,7 +139,6 @@ Directory Hierarchy: /at91 Files specific to Atmel AT91RM9200 CPU /imx Files specific to Freescale MC9328 i.MX CPUs /s3c24x0 Files specific to Samsung S3C24X0 CPUs - /arm925t Files specific to ARM 925 CPUs /arm926ejs Files specific to ARM 926 CPUs /arm1136 Files specific to ARM 1136 CPUs /ixp Files specific to Intel XScale IXP CPUs diff --git a/arch/arm/cpu/arm925t/Makefile b/arch/arm/cpu/arm925t/Makefile deleted file mode 100644 index 40d2156..0000000 --- a/arch/arm/cpu/arm925t/Makefile +++ /dev/null @@ -1,34 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -include $(TOPDIR)/config.mk - -LIB = $(obj)lib$(CPU).o - -START = start.o - -COBJS += cpu.o -COBJS += omap925.o -COBJS += timer.o - -SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) -START := $(addprefix $(obj),$(START)) - -all: $(obj).depend $(START) $(LIB) - -$(LIB): $(OBJS) - $(call cmd_link_o_target, $(OBJS)) - -######################################################################### - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -######################################################################### diff --git a/arch/arm/cpu/arm925t/config.mk b/arch/arm/cpu/arm925t/config.mk deleted file mode 100644 index 58fd756..0000000 --- a/arch/arm/cpu/arm925t/config.mk +++ /dev/null @@ -1,17 +0,0 @@ -# -# (C) Copyright 2002 -# Gary Jennejohn, DENX Software Engineering, <garyj(a)denx.de> -# -# SPDX-License-Identifier: GPL-2.0+ -# - -PLATFORM_RELFLAGS += -fno-common -ffixed-r8 -msoft-float - -PLATFORM_CPPFLAGS += -march=armv4 -# ========================================================================= -# -# Supply options according to compiler version -# -# ========================================================================= -PF_RELFLAGS_SLB_AT := $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) -PLATFORM_RELFLAGS += $(PF_RELFLAGS_SLB_AT) diff --git a/arch/arm/cpu/arm925t/cpu.c b/arch/arm/cpu/arm925t/cpu.c deleted file mode 100644 index d0f8e1e..0000000 --- a/arch/arm/cpu/arm925t/cpu.c +++ /dev/null @@ -1,50 +0,0 @@ -/* - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger(a)sysgo.de> - * - * (C) Copyright 2002 - * Gary Jennejohn, DENX Software Engineering, <garyj(a)denx.de> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * CPU specific code - */ - -#include <common.h> -#include <command.h> -#include <arm925t.h> -#include <asm/system.h> - -static void cache_flush(void); - -int cleanup_before_linux (void) -{ - /* - * this function is called just before we call linux - * it prepares the processor for linux - * - * we turn off caches etc ... - */ - - disable_interrupts (); - - - /* turn off I/D-cache */ - icache_disable(); - dcache_disable(); - /* flush I/D-cache */ - cache_flush(); - - return 0; -} - -/* flush I/D-cache */ -static void cache_flush (void) -{ - unsigned long i = 0; - - asm ("mcr p15, 0, %0, c7, c7, 0": :"r" (i)); -} diff --git a/arch/arm/cpu/arm925t/omap925.c b/arch/arm/cpu/arm925t/omap925.c deleted file mode 100644 index c0402d1..0000000 --- a/arch/arm/cpu/arm925t/omap925.c +++ /dev/null @@ -1,23 +0,0 @@ -/* - * (C) Copyright 2003 - * Texas Instruments <www.ti.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <command.h> -#include <arm925t.h> - -#define MIF_CONFIG_REG 0xFFFECC0C -#define FLASH_GLOBAL_CTRL_NWP 1 - -void archflashwp (void *archdata, int wp) -{ - ulong *fgc = (ulong *) MIF_CONFIG_REG; - - if (wp == 1) - *fgc &= ~FLASH_GLOBAL_CTRL_NWP; - else - *fgc |= FLASH_GLOBAL_CTRL_NWP; -} diff --git a/arch/arm/cpu/arm925t/start.S b/arch/arm/cpu/arm925t/start.S deleted file mode 100644 index 1e765b7..0000000 --- a/arch/arm/cpu/arm925t/start.S +++ /dev/null @@ -1,382 +0,0 @@ -/* - * armboot - Startup Code for ARM925 CPU-core - * - * Copyright (c) 2003 Texas Instruments - * - * ----- Adapted for OMAP1510 from ARM920 code ------ - * - * Copyright (c) 2001 Marius Gröger <mag(a)sysgo.de> - * Copyright (c) 2002 Alex Züpke <azu(a)sysgo.de> - * Copyright (c) 2002 Gary Jennejohn <garyj(a)denx.de> - * Copyright (c) 2003 Richard Woodruff <r-woodruff2(a)ti.com> - * Copyright (c) 2003 Kshitij <kshitij(a)ti.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <asm-offsets.h> -#include <config.h> -#include <version.h> - -/* - ************************************************************************* - * - * Jump vector table as in table 3.1 in [1] - * - ************************************************************************* - */ - - -.globl _start -_start: b reset - ldr pc, _undefined_instruction - ldr pc, _software_interrupt - ldr pc, _prefetch_abort - ldr pc, _data_abort - ldr pc, _not_used - ldr pc, _irq - ldr pc, _fiq - -_undefined_instruction: .word undefined_instruction -_software_interrupt: .word software_interrupt -_prefetch_abort: .word prefetch_abort -_data_abort: .word data_abort -_not_used: .word not_used -_irq: .word irq -_fiq: .word fiq - - .balignl 16,0xdeadbeef - - -/* - ************************************************************************* - * - * Startup Code (reset vector) - * - * do important init only if we don't start from memory! - * setup Memory and board specific bits prior to relocation. - * relocate armboot to ram - * setup stack - * - ************************************************************************* - */ - -.globl _TEXT_BASE -_TEXT_BASE: -#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_TEXT_BASE) - .word CONFIG_SPL_TEXT_BASE -#else - .word CONFIG_SYS_TEXT_BASE -#endif - -/* - * These are defined in the board-specific linker script. - * Subtracting _start from them lets the linker put their - * relative position in the executable instead of leaving - * them null. - */ -.globl _bss_start_ofs -_bss_start_ofs: - .word __bss_start - _start - -.globl _bss_end_ofs -_bss_end_ofs: - .word __bss_end - _start - -.globl _end_ofs -_end_ofs: - .word _end - _start - -#ifdef CONFIG_USE_IRQ -/* IRQ stack memory (calculated at run-time) */ -.globl IRQ_STACK_START -IRQ_STACK_START: - .word 0x0badc0de - -/* IRQ stack memory (calculated at run-time) */ -.globl FIQ_STACK_START -FIQ_STACK_START: - .word 0x0badc0de -#endif - -/* IRQ stack memory (calculated at run-time) + 8 bytes */ -.globl IRQ_STACK_START_IN -IRQ_STACK_START_IN: - .word 0x0badc0de - -/* - * the actual reset code - */ - -reset: - /* - * set the cpu to SVC32 mode - */ - mrs r0,cpsr - bic r0,r0,#0x1f - orr r0,r0,#0xd3 - msr cpsr,r0 - - /* - * Set up 925T mode - */ - mov r1, #0x81 /* Set ARM925T configuration. */ - mcr p15, 0, r1, c15, c1, 0 /* Write ARM925T configuration register. */ - - /* - * turn off the watchdog, unlock/diable sequence - */ - mov r1, #0xF5 - ldr r0, =WDTIM_MODE - strh r1, [r0] - mov r1, #0xA0 - strh r1, [r0] - - /* - * mask all IRQs by setting all bits in the INTMR - default - */ - mov r1, #0xffffffff - ldr r0, =REG_IHL1_MIR - str r1, [r0] - ldr r0, =REG_IHL2_MIR - str r1, [r0] - - /* - * wait for dpll to lock - */ - ldr r0, =CK_DPLL1 - mov r1, #0x10 - strh r1, [r0] -poll1: - ldrh r1, [r0] - ands r1, r1, #0x01 - beq poll1 - - /* - * we do sys-critical inits only at reboot, - * not when booting from ram! - */ -#ifndef CONFIG_SKIP_LOWLEVEL_INIT - bl cpu_init_crit -#endif - - bl _main - -/*------------------------------------------------------------------------------*/ - - .globl c_runtime_cpu_setup -c_runtime_cpu_setup: - - mov pc, lr - -/* - ************************************************************************* - * - * CPU_init_critical registers - * - * setup important registers - * setup memory timing - * - ************************************************************************* - */ - - -cpu_init_crit: - /* - * flush v4 I/D caches - */ - mov r0, #0 - mcr p15, 0, r0, c7, c7, 0 /* flush v3/v4 cache */ - mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */ - - /* - * disable MMU stuff and caches - */ - mrc p15, 0, r0, c1, c0, 0 - bic r0, r0, #0x00002300 @ clear bits 13, 9:8 (--V- --RS) - bic r0, r0, #0x00000087 @ clear bits 7, 2:0 (B--- -CAM) - orr r0, r0, #0x00000002 @ set bit 2 (A) Align - orr r0, r0, #0x00001000 @ set bit 12 (I) I-Cache - mcr p15, 0, r0, c1, c0, 0 - - /* - * Go setup Memory and board specific bits prior to relocation. - */ - mov ip, lr /* perserve link reg across call */ - bl lowlevel_init /* go setup pll,mux,memory */ - mov lr, ip /* restore link */ - mov pc, lr /* back to my caller */ -/* - ************************************************************************* - * - * Interrupt handling - * - ************************************************************************* - */ - -@ -@ IRQ stack frame. -@ -#define S_FRAME_SIZE 72 - -#define S_OLD_R0 68 -#define S_PSR 64 -#define S_PC 60 -#define S_LR 56 -#define S_SP 52 - -#define S_IP 48 -#define S_FP 44 -#define S_R10 40 -#define S_R9 36 -#define S_R8 32 -#define S_R7 28 -#define S_R6 24 -#define S_R5 20 -#define S_R4 16 -#define S_R3 12 -#define S_R2 8 -#define S_R1 4 -#define S_R0 0 - -#define MODE_SVC 0x13 -#define I_BIT 0x80 - -/* - * use bad_save_user_regs for abort/prefetch/undef/swi ... - * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling - */ - - .macro bad_save_user_regs - sub sp, sp, #S_FRAME_SIZE @ carve out a frame on current user stack - stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12 - - ldr r2, IRQ_STACK_START_IN - ldmia r2, {r2 - r3} @ get values for "aborted" pc and cpsr (into parm regs) - add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack - - add r5, sp, #S_SP - mov r1, lr - stmia r5, {r0 - r3} @ save sp_SVC, lr_SVC, pc, cpsr - mov r0, sp @ save current stack into r0 (param register) - .endm - - .macro irq_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - add r8, sp, #S_PC @ !!!! R8 NEEDS to be saved !!!! a reserved stack spot would be good. - stmdb r8, {sp, lr}^ @ Calling SP, LR - str lr, [r8, #0] @ Save calling PC - mrs r6, spsr - str r6, [r8, #4] @ Save CPSR - str r0, [r8, #8] @ Save OLD_R0 - mov r0, sp - .endm - - .macro irq_restore_user_regs - ldmia sp, {r0 - lr}^ @ Calling r0 - lr - mov r0, r0 - ldr lr, [sp, #S_PC] @ Get PC - add sp, sp, #S_FRAME_SIZE - subs pc, lr, #4 @ return & move spsr_svc into cpsr - .endm - - .macro get_bad_stack - ldr r13, IRQ_STACK_START_IN - - str lr, [r13] @ save caller lr in position 0 of saved stack - mrs lr, spsr @ get the spsr - str lr, [r13, #4] @ save spsr in position 1 of saved stack - - mov r13, #MODE_SVC @ prepare SVC-Mode - @ msr spsr_c, r13 - msr spsr, r13 @ switch modes, make sure moves will execute - mov lr, pc @ capture return pc - movs pc, lr @ jump to next instruction & switch modes. - .endm - - .macro get_irq_stack @ setup IRQ stack - ldr sp, IRQ_STACK_START - .endm - - .macro get_fiq_stack @ setup FIQ stack - ldr sp, FIQ_STACK_START - .endm - -/* - * exception handlers - */ - .align 5 -undefined_instruction: - get_bad_stack - bad_save_user_regs - bl do_undefined_instruction - - .align 5 -software_interrupt: - get_bad_stack - bad_save_user_regs - bl do_software_interrupt - - .align 5 -prefetch_abort: - get_bad_stack - bad_save_user_regs - bl do_prefetch_abort - - .align 5 -data_abort: - get_bad_stack - bad_save_user_regs - bl do_data_abort - - .align 5 -not_used: - get_bad_stack - bad_save_user_regs - bl do_not_used - -#ifdef CONFIG_USE_IRQ - - .align 5 -irq: - get_irq_stack - irq_save_user_regs - bl do_irq - irq_restore_user_regs - - .align 5 -fiq: - get_fiq_stack - /* someone ought to write a more effiction fiq_save_user_regs */ - irq_save_user_regs - bl do_fiq - irq_restore_user_regs - -#else - - .align 5 -irq: - get_bad_stack - bad_save_user_regs - bl do_irq - - .align 5 -fiq: - get_bad_stack - bad_save_user_regs - bl do_fiq - -#endif - - .align 5 -.globl reset_cpu -reset_cpu: - ldr r1, rstctl1 /* get clkm1 reset ctl */ - mov r3, #0x3 /* dsp_en + arm_rst = global reset */ - strh r3, [r1] /* force reset */ - mov r0, r0 -_loop_forever: - b _loop_forever -rstctl1: - .word 0xfffece10 diff --git a/arch/arm/cpu/arm925t/timer.c b/arch/arm/cpu/arm925t/timer.c deleted file mode 100644 index e56b576..0000000 --- a/arch/arm/cpu/arm925t/timer.c +++ /dev/null @@ -1,104 +0,0 @@ -/* - * (C) Copyright 2009 - * 2N Telekomunikace, <www.2n.cz> - * - * (C) Copyright 2003 - * Texas Instruments, <www.ti.com> - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger(a)sysgo.de> - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Alex Zuepke <azu(a)sysgo.de> - * - * (C) Copyright 2002 - * Gary Jennejohn, DENX Software Engineering, <garyj(a)denx.de> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <arm925t.h> -#include <configs/omap1510.h> -#include <asm/io.h> - -#define TIMER_LOAD_VAL 0xffffffff -#define TIMER_CLOCK (CONFIG_SYS_CLK_FREQ / (2 << CONFIG_SYS_PTV)) - -static uint32_t timestamp; -static uint32_t lastdec; - -/* nothing really to do with interrupts, just starts up a counter. */ -int timer_init (void) -{ - /* Start the decrementer ticking down from 0xffffffff */ - __raw_writel(TIMER_LOAD_VAL, CONFIG_SYS_TIMERBASE + LOAD_TIM); - __raw_writel(MPUTIM_ST | MPUTIM_AR | MPUTIM_CLOCK_ENABLE | - (CONFIG_SYS_PTV << MPUTIM_PTV_BIT), - CONFIG_SYS_TIMERBASE + CNTL_TIMER); - - /* init the timestamp and lastdec value */ - lastdec = __raw_readl(CONFIG_SYS_TIMERBASE + READ_TIM) / - (TIMER_CLOCK / CONFIG_SYS_HZ); - timestamp = 0; /* start "advancing" time stamp from 0 */ - - return 0; -} - -/* - * timer without interrupts - */ -ulong get_timer (ulong base) -{ - return get_timer_masked () - base; -} - -/* delay x useconds AND preserve advance timestamp value */ -void __udelay (unsigned long usec) -{ - int32_t tmo = usec * (TIMER_CLOCK / 1000) / 1000; - uint32_t now, last = __raw_readl(CONFIG_SYS_TIMERBASE + READ_TIM); - - while (tmo > 0) { - now = __raw_readl(CONFIG_SYS_TIMERBASE + READ_TIM); - if (last < now) /* count down timer underflow */ - tmo -= TIMER_LOAD_VAL - now + last; - else - tmo -= last - now; - last = now; - } -} - -ulong get_timer_masked (void) -{ - uint32_t now = __raw_readl(CONFIG_SYS_TIMERBASE + READ_TIM) / - (TIMER_CLOCK / CONFIG_SYS_HZ); - if (lastdec < now) /* count down timer underflow */ - timestamp += TIMER_LOAD_VAL / (TIMER_CLOCK / CONFIG_SYS_HZ) - - now + lastdec; - else - timestamp += lastdec - now; - lastdec = now; - - return timestamp; -} - -/* - * This function is derived from PowerPC code (read timebase as long long). - * On ARM it just returns the timer value. - */ -unsigned long long get_ticks(void) -{ - return get_timer(0); -} - -/* - * This function is derived from PowerPC code (timebase clock frequency). - * On ARM it returns the number of timer ticks per second. - */ -ulong get_tbclk (void) -{ - return CONFIG_SYS_HZ; -} diff --git a/board/ti/omap1510inn/Makefile b/board/ti/omap1510inn/Makefile deleted file mode 100644 index ad5a7eb..0000000 --- a/board/ti/omap1510inn/Makefile +++ /dev/null @@ -1,29 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -include $(TOPDIR)/config.mk - -LIB = $(obj)lib$(BOARD).o - -COBJS := omap1510innovator.o -SOBJS := lowlevel_init.o - -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS)) -SOBJS := $(addprefix $(obj),$(SOBJS)) - -$(LIB): $(obj).depend $(OBJS) $(SOBJS) - $(call cmd_link_o_target, $(OBJS) $(SOBJS)) - -######################################################################### - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -######################################################################### diff --git a/board/ti/omap1510inn/config.mk b/board/ti/omap1510inn/config.mk deleted file mode 100644 index 67fe0bd..0000000 --- a/board/ti/omap1510inn/config.mk +++ /dev/null @@ -1,25 +0,0 @@ -# -# (C) Copyright 2002 -# Gary Jennejohn, DENX Software Engineering, <garyj(a)denx.de> -# David Mueller, ELSOFT AG, <d.mueller(a)elsoft.ch> -# -# (C) Copyright 2003 -# Texas Instruments, <www.ti.com> -# Kshitij Gupta <Kshitij(a)ti.com> -# -# TI Innovator board with OMAP1510 (ARM925T) cpu -# see http://www.ti.com/ for more information on Texas Insturments -# -# Innovator has 1 bank of 256 MB SDRAM -# Physical Address: -# 1000'0000 to 2000'0000 -# -# -# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000 (mem base + reserved) -# -# we load ourself to 1108'0000 -# -# - - -CONFIG_SYS_TEXT_BASE = 0x11080000 diff --git a/board/ti/omap1510inn/lowlevel_init.S b/board/ti/omap1510inn/lowlevel_init.S deleted file mode 100644 index 4d3ec39..0000000 --- a/board/ti/omap1510inn/lowlevel_init.S +++ /dev/null @@ -1,380 +0,0 @@ -/* - * Board specific setup info - * - * (C) Copyright 2003 - * Texas Instruments, <www.ti.com> - * - * -- Some bits of code used from rrload's head_OMAP1510.s -- - * Copyright (C) 2002 RidgeRun, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <config.h> -#include <version.h> - -#if defined(CONFIG_OMAP1510) -#include <./configs/omap1510.h> -#endif - -#define OMAP1510_CLKS ((1<<EN_XORPCK)|(1<<EN_PERCK)|(1<<EN_TIMCK)|(1<<EN_GPIOCK)) - - -_TEXT_BASE: - .word CONFIG_SYS_TEXT_BASE /* sdram load addr from config.mk */ - -.globl lowlevel_init -lowlevel_init: - - /* - * Configure 1510 pins functions to match our board. - */ - ldr r0, REG_PULL_DWN_CTRL_0 - ldr r1, VAL_PULL_DWN_CTRL_0 - str r1, [r0] - ldr r0, REG_PULL_DWN_CTRL_1 - ldr r1, VAL_PULL_DWN_CTRL_1 - str r1, [r0] - ldr r0, REG_PULL_DWN_CTRL_2 - ldr r1, VAL_PULL_DWN_CTRL_2 - str r1, [r0] - ldr r0, REG_PULL_DWN_CTRL_3 - ldr r1, VAL_PULL_DWN_CTRL_3 - str r1, [r0] - ldr r0, REG_FUNC_MUX_CTRL_4 - ldr r1, VAL_FUNC_MUX_CTRL_4 - str r1, [r0] - ldr r0, REG_FUNC_MUX_CTRL_5 - ldr r1, VAL_FUNC_MUX_CTRL_5 - str r1, [r0] - ldr r0, REG_FUNC_MUX_CTRL_6 - ldr r1, VAL_FUNC_MUX_CTRL_6 - str r1, [r0] - ldr r0, REG_FUNC_MUX_CTRL_7 - ldr r1, VAL_FUNC_MUX_CTRL_7 - str r1, [r0] - ldr r0, REG_FUNC_MUX_CTRL_8 - ldr r1, VAL_FUNC_MUX_CTRL_8 - str r1, [r0] - ldr r0, REG_FUNC_MUX_CTRL_9 - ldr r1, VAL_FUNC_MUX_CTRL_9 - str r1, [r0] - ldr r0, REG_FUNC_MUX_CTRL_A - ldr r1, VAL_FUNC_MUX_CTRL_A - str r1, [r0] - ldr r0, REG_FUNC_MUX_CTRL_B - ldr r1, VAL_FUNC_MUX_CTRL_B - str r1, [r0] - ldr r0, REG_FUNC_MUX_CTRL_C - ldr r1, VAL_FUNC_MUX_CTRL_C - str r1, [r0] - ldr r0, REG_FUNC_MUX_CTRL_D - ldr r1, VAL_FUNC_MUX_CTRL_D - str r1, [r0] - ldr r0, REG_VOLTAGE_CTRL_0 - ldr r1, VAL_VOLTAGE_CTRL_0 - str r1, [r0] - ldr r0, REG_TEST_DBG_CTRL_0 - ldr r1, VAL_TEST_DBG_CTRL_0 - str r1, [r0] - ldr r0, REG_MOD_CONF_CTRL_0 - ldr r1, VAL_MOD_CONF_CTRL_0 - str r1, [r0] - - /* Move to 1510 mode */ - ldr r0, REG_COMP_MODE_CTRL_0 - ldr r1, VAL_COMP_MODE_CTRL_0 - str r1, [r0] - - /* Set up Traffic Ctlr*/ - ldr r0, REG_TC_IMIF_PRIO - mov r1, #0x0 - str r1, [r0] - ldr r0, REG_TC_EMIFS_PRIO - str r1, [r0] - ldr r0, REG_TC_EMIFF_PRIO - str r1, [r0] - - ldr r0, REG_TC_EMIFS_CONFIG - ldr r1, [r0] - bic r1, r1, #0x08 /* clear the global power-down enable PDE bit */ - bic r1, r1, #0x01 /* write protect flash by clearing the WP bit */ - str r1, [r0] /* EMIFS GlB Configuration. (value 0x12 most likely) */ - - /* Setup some clock domains */ - ldr r1, =OMAP1510_CLKS - ldr r0, REG_ARM_IDLECT2 - strh r1, [r0] /* CLKM, Clock domain control. */ - - mov r1, #0x01 /* PER_EN bit */ - ldr r0, REG_ARM_RSTCT2 - strh r1, [r0] /* CLKM; Peripheral reset. */ - - /* Set CLKM to Sync-Scalable */ - /* I supposidly need to enable the dsp clock before switching */ - mov r1, #0x1000 - ldr r0, REG_ARM_SYSST - strh r1, [r0] - mov r0, #0x400 -1: - subs r0, r0, #0x1 /* wait for any bubbles to finish */ - bne 1b - - ldr r1, VAL_ARM_CKCTL /* use 12Mhz ref, PER must be <= 50Mhz so /2 */ - ldr r0, REG_ARM_CKCTL - strh r1, [r0] - - /* setup DPLL 1 */ - ldr r1, VAL_DPLL1_CTL - ldr r0, REG_DPLL1_CTL - strh r1, [r0] - ands r1, r1, #0x10 /* Check if PLL is enabled. */ - beq lock_end /* Do not look for lock if BYPASS selected */ -2: - ldrh r1, [r0] - ands r1, r1, #0x01 /* Check the LOCK bit. */ - beq 2b /* ...loop until bit goes hi. */ -lock_end: - - /* Set memory timings corresponding to the new clock speed */ - - /* Check execution location to determine current execution location - * and branch to appropriate initialization code. - */ - mov r0, #0x10000000 /* Load physical SDRAM base. */ - mov r1, pc /* Get current execution location. */ - /* Zero all but top 6 bits of PC, as they alone detect whether an - * address is in the range 0x1000:0000-0x13ff:ffff, the 64M sized - * valid range for SDRAM on the OMAP 1510/5910. - */ - and r1, r1, #0xfc000000 - cmp r1, r0 /* Compare. */ - beq skip_sdram /* Skip over EMIF-fast initialization - * if running from SDRAM. - */ - - /* - * Delay for SDRAM initialization. - */ - mov r3, #0x1800 /* value should be checked */ -3: - subs r3, r3, #0x1 /* Decrement count */ - bne 3b - - /* - * Set SDRAM control values. Disable refresh before MRS command. - */ - ldr r0, VAL_TC_EMIFF_SDRAM_CONFIG /* get good value */ - bic r3, r0, #0xC /* (BIT3|BIT2) ulConfig with auto-refresh disabled. */ - orr r3, r3, #0x8000000 /* (BIT27) Disable CLK when Power down or Self-Refresh */ - orr r3, r3, #0x4000000 /* BIT26 Power Down Enable */ - ldr r2, REG_TC_EMIFF_SDRAM_CONFIG /* Point to configuration register. */ - str r3, [r2] /* Store the passed value with AR disabled. */ - - ldr r1, VAL_TC_EMIFF_MRS /* get MRS value */ - ldr r2, REG_TC_EMIFF_MRS /* Point to MRS register. */ - str r1, [r2] /* Store the passed value.*/ - - ldr r2, REG_TC_EMIFF_SDRAM_CONFIG /* Point to configuration register. */ - str r0, [r2] /* Store the passed value. */ - - /* - * Delay for SDRAM initialization. - */ - mov r3, #0x1800 -4: - subs r3, r3, #1 /* Decrement count. */ - bne 4b - -skip_sdram: - - /* slow interface */ - ldr r1, VAL_TC_EMIFS_CS0_CONFIG - ldr r0, REG_TC_EMIFS_CS0_CONFIG - str r1, [r0] /* Chip Select 0 */ - ldr r1, VAL_TC_EMIFS_CS1_CONFIG - ldr r0, REG_TC_EMIFS_CS1_CONFIG - str r1, [r0] /* Chip Select 1 */ - ldr r1, VAL_TC_EMIFS_CS2_CONFIG - ldr r0, REG_TC_EMIFS_CS2_CONFIG - str r1, [r0] /* Chip Select 2 */ - ldr r1, VAL_TC_EMIFS_CS3_CONFIG - ldr r0, REG_TC_EMIFS_CS3_CONFIG - str r1, [r0] /* Chip Select 3 */ - - /* Next, Enable the RS232 Line Drivers in the FPGA. */ - /* Also, power on the audio CODEC's amplifier here, */ - /* which will make a noise on the audio output. */ - /* This is done here instead of in the kernel so there */ - /* isn't a loud popping noise at the start of each */ - /* song. */ - /* Also, disable the CODEC's clocks. */ - /* omap1510-HelenP1 [specific] */ - - ldr r0, REG_FPGA_POWER - mov r1, #0 - ldr r2, REG_FPGA_DIP_SWITCH - ldrb r3, [r2] - cmp r3, #0x8 - movne r1, #0x62 /* Enable the RS232 Line Drivers in the EPLD */ - strb r1, [r0] - ldr r0, REG_FPGA_AUDIO - mov r1, #0x0 /* Disable sound driver (CODEC clocks) */ - strb r1, [r0] - - /* back to arch calling code */ - mov pc, lr - -/* the literal pools origin */ - .ltorg - -/* OMAP configuration registers */ -REG_FUNC_MUX_CTRL_0: /* 32 bits */ - .word 0xfffe1000 -REG_FUNC_MUX_CTRL_1: /* 32 bits */ - .word 0xfffe1004 -REG_FUNC_MUX_CTRL_2: /* 32 bits */ - .word 0xfffe1008 -REG_COMP_MODE_CTRL_0: /* 32 bits */ - .word 0xfffe100c -REG_FUNC_MUX_CTRL_3: /* 32 bits */ - .word 0xfffe1010 -REG_FUNC_MUX_CTRL_4: /* 32 bits */ - .word 0xfffe1014 -REG_FUNC_MUX_CTRL_5: /* 32 bits */ - .word 0xfffe1018 -REG_FUNC_MUX_CTRL_6: /* 32 bits */ - .word 0xfffe101c -REG_FUNC_MUX_CTRL_7: /* 32 bits */ - .word 0xfffe1020 -REG_FUNC_MUX_CTRL_8: /* 32 bits */ - .word 0xfffe1024 -REG_FUNC_MUX_CTRL_9: /* 32 bits */ - .word 0xfffe1028 -REG_FUNC_MUX_CTRL_A: /* 32 bits */ - .word 0xfffe102C -REG_FUNC_MUX_CTRL_B: /* 32 bits */ - .word 0xfffe1030 -REG_FUNC_MUX_CTRL_C: /* 32 bits */ - .word 0xfffe1034 -REG_FUNC_MUX_CTRL_D: /* 32 bits */ - .word 0xfffe1038 -REG_PULL_DWN_CTRL_0: /* 32 bits */ - .word 0xfffe1040 -REG_PULL_DWN_CTRL_1: /* 32 bits */ - .word 0xfffe1044 -REG_PULL_DWN_CTRL_2: /* 32 bits */ - .word 0xfffe1048 -REG_PULL_DWN_CTRL_3: /* 32 bits */ - .word 0xfffe104c -REG_VOLTAGE_CTRL_0: /* 32 bits */ - .word 0xfffe1060 -REG_TEST_DBG_CTRL_0: /* 32 bits */ - .word 0xfffe1070 -REG_MOD_CONF_CTRL_0: /* 32 bits */ - .word 0xfffe1080 -REG_TC_IMIF_PRIO: /* 32 bits */ - .word 0xfffecc00 -REG_TC_EMIFS_PRIO: /* 32 bits */ - .word 0xfffecc04 -REG_TC_EMIFF_PRIO: /* 32 bits */ - .word 0xfffecc08 -REG_TC_EMIFS_CONFIG: /* 32 bits */ - .word 0xfffecc0c -REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */ - .word 0xfffecc10 -REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */ - .word 0xfffecc14 -REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */ - .word 0xfffecc18 -REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */ - .word 0xfffecc1c -REG_TC_EMIFF_SDRAM_CONFIG: /* 32 bits */ - .word 0xfffecc20 -REG_TC_EMIFF_MRS: /* 32 bits */ - .word 0xfffecc24 -/* MPU clock/reset/power mode control registers */ -REG_ARM_CKCTL: /* 16 bits */ - .word 0xfffece00 -REG_ARM_IDLECT2: /* 16 bits */ - .word 0xfffece08 -REG_ARM_RSTCT2: /* 16 bits */ - .word 0xfffece14 -REG_ARM_SYSST: /* 16 bits */ - .word 0xfffece18 -/* DPLL control registers */ -REG_DPLL1_CTL: /* 16 bits */ - .word 0xfffecf00 -/* identification code register */ -REG_IDCODE: /* 32 bits */ - .word 0xfffed404 - -/* Innovator specific */ -REG_FPGA_LED_DIGIT: /* 8 bits (not used on Innovator) */ - .word 0x08000003 -REG_FPGA_POWER: /* 8 bits */ - .word 0x08000005 -REG_FPGA_AUDIO: /* 8 bits (not used on Innovator) */ - .word 0x0800000c -REG_FPGA_DIP_SWITCH: /* 8 bits (not used on Innovator) */ - .word 0x0800000e - -VAL_COMP_MODE_CTRL_0: - .word 0x0000eaef -VAL_FUNC_MUX_CTRL_4: - .word 0x00000000 -VAL_FUNC_MUX_CTRL_5: - .word 0x00000000 -VAL_FUNC_MUX_CTRL_6: - .word 0x00000001 -VAL_FUNC_MUX_CTRL_7: - .word 0x00000000 -VAL_FUNC_MUX_CTRL_8: - .word 0x10001200 -VAL_FUNC_MUX_CTRL_9: - .word 0x01201012 -VAL_FUNC_MUX_CTRL_A: - .word 0x00000248 -VAL_FUNC_MUX_CTRL_B: - .word 0x00000248 -VAL_FUNC_MUX_CTRL_C: - .word 0x09000000 -VAL_FUNC_MUX_CTRL_D: - .word 0x00000000 -VAL_PULL_DWN_CTRL_0: - .word 0x11a10000 -VAL_PULL_DWN_CTRL_1: - .word 0x2e047fff -VAL_PULL_DWN_CTRL_2: - .word 0xffd603a6 -VAL_PULL_DWN_CTRL_3: - .word 0x00003e03 -VAL_VOLTAGE_CTRL_0: - .word 0x00000007 -VAL_TEST_DBG_CTRL_0: - /* See Errata 4.13, This works around a SRAM bug, for chips below ES2.5 . - * This slows down internal SRAM accesses. - */ - .word 0x00000007 -VAL_MOD_CONF_CTRL_0: - .word 0x0b000008 -VAL_ARM_CKCTL: - .word 0x010f -VAL_DPLL1_CTL: - .word 0x2710 -VAL_TC_EMIFS_CS1_CONFIG_PRELIM: - .word 0x00001149 -VAL_TC_EMIFS_CS2_CONFIG_PRELIM: - .word 0x00004158 -VAL_TC_EMIFS_CS0_CONFIG: - .word 0x002130b0 -VAL_TC_EMIFS_CS1_CONFIG: - .word 0x0000f559 -VAL_TC_EMIFS_CS2_CONFIG: - .word 0x000055f0 -VAL_TC_EMIFS_CS3_CONFIG: - .word 0x00003331 -VAL_TC_EMIFF_SDRAM_CONFIG: - .word 0x010290fc -VAL_TC_EMIFF_MRS: - .word 0x00000027 diff --git a/board/ti/omap1510inn/omap1510innovator.c b/board/ti/omap1510inn/omap1510innovator.c deleted file mode 100644 index a2a33a0..0000000 --- a/board/ti/omap1510inn/omap1510innovator.c +++ /dev/null @@ -1,125 +0,0 @@ -/* - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger(a)sysgo.de> - * - * (C) Copyright 2002 - * David Mueller, ELSOFT AG, <d.mueller(a)elsoft.ch> - * - * (C) Copyright 2003 - * Texas Instruments, <www.ti.com> - * Kshitij Gupta <Kshitij(a)ti.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <netdev.h> - -DECLARE_GLOBAL_DATA_PTR; - -static void flash__init (void); -static void ether__init (void); - -static inline void delay (unsigned long loops) -{ - __asm__ volatile ("1:\n" - "subs %0, %1, #1\n" - "bne 1b":"=r" (loops):"0" (loops)); -} - -/* - * Miscellaneous platform dependent initialisations - */ - -int board_init (void) -{ - /* arch number of OMAP 1510-Board */ - gd->bd->bi_arch_number = MACH_TYPE_OMAP_INNOVATOR; - - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x10000100; - -/* kk - this speeds up your boot a quite a bit. However to make it - * work, you need make sure your kernel startup flush bug is fixed. - * ... rkw ... - */ - icache_enable (); - - flash__init (); - ether__init (); - return 0; -} - - -int misc_init_r (void) -{ - /* volatile ushort *gdir = (ushort *) (GPIO_DIR_CONTROL_REG); */ - /* volatile ushort *mdir = (ushort *) (MPUIO_DIR_CONTROL_REG); */ - - /* setup gpio direction to match board (no floats!) */ - /**gdir = 0xCFF9; */ - /**mdir = 0x103F; */ - - return (0); -} - -/****************************** - Routine: - Description: -******************************/ -static void flash__init (void) -{ -#define CS0_CHIP_SELECT_REG 0xfffecc10 -#define CS3_CHIP_SELECT_REG 0xfffecc1c -#define EMIFS_GlB_Config_REG 0xfffecc0c - - { - unsigned int regval; - - regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG); - regval = regval | 0x0001; /* Turn off write protection for flash devices. */ - if (regval & 0x0002) { - regval = regval & 0xfffd; /* Swap CS0 and CS3 so that flash is visible at 0x0 and eeprom at 0x0c000000. */ - /* If, instead, you want to reference flash at 0x0c000000, then it seemed the following were necessary. */ - /* *((volatile unsigned int *)CS0_CHIP_SELECT_REG) = 0x202090; / * Overrides head.S setting of 0x212090 */ - /* *((volatile unsigned int *)CS3_CHIP_SELECT_REG) = 0x202090; / * Let's flash chips be fully functional. */ - } - *((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval; - } -} - - -/****************************** - Routine: - Description: -******************************/ -static void ether__init (void) -{ -#define ETH_CONTROL_REG 0x0800000b - /* take the Ethernet controller out of reset and wait - * for the EEPROM load to complete. - */ - *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01; - udelay (3); -} - - -int dram_init (void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; - - return 0; -} - -#ifdef CONFIG_CMD_NET -int board_eth_init(bd_t *bis) -{ - int rc = 0; -#ifdef CONFIG_LAN91C96 - rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE); -#endif - return rc; -} -#endif diff --git a/boards.cfg b/boards.cfg index 211ed58..aefa1e9 100644 --- a/boards.cfg +++ b/boards.cfg @@ -71,7 +71,6 @@ cm41xx arm arm920t - - mini2440 arm arm920t mini2440 friendlyarm s3c24x0 VCMA9 arm arm920t vcma9 mpl s3c24x0 smdk2410 arm arm920t - samsung s3c24x0 -omap1510inn arm arm925t - ti integratorap_cm926ejs arm arm926ejs integrator armltd - integratorap:CM926EJ_S integratorcp_cm926ejs arm arm926ejs integrator armltd - integratorcp:CM924EJ_S aspenite arm arm926ejs - Marvell armada100 diff --git a/include/arm925t.h b/include/arm925t.h deleted file mode 100644 index 3d767b3..0000000 --- a/include/arm925t.h +++ /dev/null @@ -1,11 +0,0 @@ -/************************************************ - * NAME : arm925t.h - * Version : 23 June 2003 * - ************************************************/ - -#ifndef __ARM925T_H__ -#define __ARM925T_H__ - -void archflashwp(void *archdata, int wp); - -#endif /*__ARM925T_H__*/ diff --git a/include/configs/omap1510inn.h b/include/configs/omap1510inn.h deleted file mode 100644 index 1a7e5c7..0000000 --- a/include/configs/omap1510inn.h +++ /dev/null @@ -1,166 +0,0 @@ -/* - * (C) Copyright 2003 - * Texas Instruments. - * Kshitij Gupta <kshitij(a)ti.com> - * Configuation settings for the TI OMAP Innovator board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_ARM925T 1 /* This is an arm925t CPU */ -#define CONFIG_OMAP 1 /* in a TI OMAP core */ -#define CONFIG_OMAP1510 1 /* which is in a 1510 (helen) */ -#define CONFIG_INNOVATOROMAP1510 1 /* a Innovator Board */ - -/* input clock of PLL */ -#define CONFIG_SYS_CLK_FREQ 12000000 /* the OMAP1510 Innovator has 12MHz input clock */ - -#define CONFIG_MISC_INIT_R - -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 - -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* - * Hardware drivers - */ -/* -#define CONFIG_DRIVER_SMC9196 -#define CONFIG_SMC9196_BASE 0x08000300 -#define CONFIG_SMC9196_EXT_PHY -*/ -#define CONFIG_LAN91C96 -#define CONFIG_LAN91C96_BASE 0x08000300 -#define CONFIG_LAN91C96_EXT_PHY - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK (CONFIG_SYS_CLK_FREQ) /* can be 12M/32Khz or 48Mhz */ -#define CONFIG_SYS_NS16550_COM1 0xfffb0000 /* uart1, bluetooth uart on helen */ - -/* - * select serial console configuration - */ -#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on OMAP1510 Innovator */ - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_ENV_OVERWRITE -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 115200 - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DHCP - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH - - -#include <configs/omap1510.h> - -#define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOTARGS "console=ttyS0,115200n8 noinitrd root=/dev/nfs ip=bootp" -#define CONFIG_BOOTCOMMAND "bootp;tftp;bootm" -#define CONFIG_SYS_AUTOLOAD "n" /* No autoload */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */ -/* what's this ? it's not used anywhere */ -#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */ -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "OMAP1510 Innovator # " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x12000000 /* 32 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x10000000 /* default load address */ - -/* The 1510 has 3 timers, they can be driven by the RefClk (12MHz) or by DPLL1. - * This time is further subdivided by a local divisor. - */ -#define CONFIG_SYS_TIMERBASE OMAP1510_TIMER1_BASE /* use timer 1 */ -#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ -#define CONFIG_SYS_HZ 1000 - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ -#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ -#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */ -#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */ - -#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 - -#define PHYS_SRAM 0x20000000 - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define PHYS_FLASH_SIZE 0x01000000 /* 16MB */ -#define PHYS_FLASH_SECT_SIZE (128*1024) /* Size of a sector (128kB) */ -#define CONFIG_SYS_MAX_FLASH_SECT (128) /* max number of sectors on one chip */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + PHYS_FLASH_SECT_SIZE) -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* Monitor at beginning of flash */ -#define CONFIG_SYS_MONITOR_LEN PHYS_FLASH_SECT_SIZE /* Reserve 1 sector */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + PHYS_FLASH_SIZE } - -/*----------------------------------------------------------------------- - * FLASH driver setup - */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash memory is CFI compliant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/mtd/cfi_flash.c */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use hardware sector protection */ - -/* timeout values are in ticks */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Erase */ -#define CONFIG_SYS_FLASH_WRITE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Write */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SECT_SIZE PHYS_FLASH_SECT_SIZE /* Total Size of Environment Sector */ -#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE -#define CONFIG_ENV_OFFSET ( CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN ) /* Environment after Monitor */ - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_SP_ADDR PHYS_SRAM - -#endif /* __CONFIG_H */ -- 1.8.1.2

3 8

[U-Boot] [PATCH 0/9] net: tsec: Driver portability fixes and cleanup
by Claudiu Manoil 07 Oct '13

07 Oct '13

Though the first 3 patches fix tsec's driver mcast() instance primarily, the fix from net.h was propagated to other drivers too, as appropriate. Notably, these fixes also end up in removal of some unwanted global static vars from the tsec driver. The rest of the patches are driver portability fixes, so that the tsec driver may work on little endian architectures as well. The issues uncovered by the sparse tool where also addressed in the process. All checkpatch issues were addressed, including those on existing code. Only a couple of CamelCase warnings remain, coming from the net stack code (see NetReceive(), NetRxPackets[]). Claudiu Manoil (9): net: Fix mcast function pointer prototype net: tsec: Fix and cleanup tsec_mcast_addr() net: tsec: Fix priv pointer in tsec_mcast_addr() net: tsec: Cleanup tsec regs init and fix __iomem warns net: fsl_mdio: Fix warnings for __iomem pointers net: tsec: Fix CamelCase issues around BD code net: tsec: Use portable types and accessors for BDs net: tsec: Use portable regs type (uint->u32) net: tsec: Fix mac addr setup portability, cleanup drivers/net/fsl_mdio.c | 17 ++- drivers/net/rtl8139.c | 2 +- drivers/net/tsec.c | 200 ++++++++++++++-------------- include/fsl_mdio.h | 8 +- include/net.h | 2 +- include/tsec.h | 345 +++++++++++++++++++++++++------------------------ 6 files changed, 296 insertions(+), 278 deletions(-) -- 1.7.11.7

3 29

[U-Boot] [Uboot][PATCH] drivers: spi: macronix: Add MX66L51235L data
by Sourav Poddar 07 Oct '13

07 Oct '13

Add support for macronix "MX66L51235L" flash device. Signed-off-by: Sourav Poddar <sourav.poddar(a)ti.com> --- drivers/mtd/spi/macronix.c | 5 +++++ 1 files changed, 5 insertions(+), 0 deletions(-) diff --git a/drivers/mtd/spi/macronix.c b/drivers/mtd/spi/macronix.c index 70435eb..5a528c3 100644 --- a/drivers/mtd/spi/macronix.c +++ b/drivers/mtd/spi/macronix.c @@ -61,6 +61,11 @@ static const struct macronix_spi_flash_params macronix_spi_flash_table[] = { .nr_blocks = 256, .name = "MX25L12855E", }, + { + .idcode = 0x201a, + .nr_blocks = 512, + .name = "MX66L51235L", + }, }; struct spi_flash *spi_flash_probe_macronix(struct spi_slave *spi, u8 *idcode) -- 1.7.1

2 4

[U-Boot] [PATCHv2 0/8] qspi controller: Normal, quad and memory mapped read support
by Sourav Poddar 07 Oct '13

07 Oct '13

This patch series add uboot ti qspi controller driver. QSPI is a kind of spi module that allows single, dual and quad read access to external spi devices. The module has a memory mapped interface which provide direct interface for accessing data form external spi devices. SPI mode ------- SPI mode uses mtd spi framework for transfer and reception of data. Can be used in: 1. Normal mode: use single pin for transfers 2. Dual Mode: use two pins for transfers. 3. Quad mode: use four pin for transfer Memory mapped read mode ----------------------- In this, SPI controller is configured using configuration port and then controler is switched to memory mapped port for data read. Series proposed suport for quad read as well as memory mapped read in spi mtd frameowrk as well as ti qpsi driver. Test info is attached as the last patch in the series. Matt Porter (3): omap5: add qspi support spi: add TI QSPI driver dra7xx_evm: add SPL API, QSPI, and serial flash support Ravikumar Kattekola (1): drivers: mtd: qspi: Add quad read support Sourav Poddar (4): armv7: hw_data: change clock divider setting. drivers: mtd: spi: Modify read/write command for sfl256s flash. driver: spi: Add memory mapped read support README: qspi usecase and testing documentation. arch/arm/cpu/armv7/omap5/hw_data.c | 9 +- arch/arm/cpu/armv7/omap5/prcm-regs.c | 1 + arch/arm/include/asm/arch-omap5/omap.h | 3 + arch/arm/include/asm/arch-omap5/spl.h | 1 + arch/arm/include/asm/omap_common.h | 1 + board/ti/dra7xx/mux_data.h | 10 + doc/README.ti_qspi_dra_test | 38 ++++ doc/README.ti_qspi_flash | 47 +++++ drivers/mtd/spi/spansion.c | 1 + drivers/mtd/spi/spi_flash.c | 148 ++++++++++++++- drivers/mtd/spi/spi_flash_internal.h | 2 + drivers/spi/Makefile | 1 + drivers/spi/ti_qspi.c | 327 ++++++++++++++++++++++++++++++++ include/configs/dra7xx_evm.h | 19 ++ include/spi.h | 5 + 15 files changed, 610 insertions(+), 3 deletions(-) create mode 100644 doc/README.ti_qspi_dra_test create mode 100644 doc/README.ti_qspi_flash create mode 100644 drivers/spi/ti_qspi.c

4 26