April 2013 - U-Boot

[U-Boot] [PATCH] mx31pdk: Remove watchdog support
by Fabio Estevam 10 Apr '13

10 Apr '13

The conversion of mx31pdk to SPL NAND fixed the boot issue, but we start seeing resets in loop, which prevents us from reaching the U-boot prompt. Until the proper fix can be identified, disable watchdog, so that mx31pdk can be functional again. Signed-off-by: Fabio Estevam <fabio.estevam(a)freescale.com> --- include/configs/mx31pdk.h | 2 -- 1 file changed, 2 deletions(-) diff --git a/include/configs/mx31pdk.h b/include/configs/mx31pdk.h index 34e4295..da894c4 100644 --- a/include/configs/mx31pdk.h +++ b/include/configs/mx31pdk.h @@ -60,8 +60,6 @@ #define CONFIG_MXC_UART #define CONFIG_MXC_UART_BASE UART1_BASE -#define CONFIG_HW_WATCHDOG -#define CONFIG_IMX_WATCHDOG #define CONFIG_MXC_GPIO #define CONFIG_HARD_SPI -- 1.7.9.5

3 2

Re: [U-Boot] [PATCH 1/1] powerpc/lib: fix unsafe register handling in wait_ticks
by Tom Rini 10 Apr '13

10 Apr '13

On Tue, Apr 09, 2013 at 05:10:59PM +0200, Mats K??rrman wrote: > If watchdog is enabled, the arch/powerpc/lib/ticks.S::wait_ticks() function > calls the function specified by the WATCHDOG_RESET macro. > The wait_ticks function depends on the registers r0, r6 and r7 being > preserved however that is not guaranteed, e.g. if the reset function is a > C function this will probably overwrite r0 and cause an endless loop. > > The following patch changes to using r14+r15 instead of r6+r7 (to resemble > what would have been generated by a C compiler) and saves all necessary > registers on the stack. > > The patch has been tested on a custom MPC5125 based machine using the 512x > powerpc architecture. > > Signed-off-by: Mats Karrman <mats.karrman(a)tritech.se> > Cc: Wolfgang Denk <wd(a)denx.de> > Acked-by: Joakim Tjernlund <joakim.tjernlund(a)transmode.se> > Tested-by: Stefan Roese <sr(a)denx.de> Applied to u-boot/master, thanks! -- Tom

1 0

[U-Boot] [PATCH] am335x: Update timings for the beaglebone again
by Tom Rini 10 Apr '13

10 Apr '13

After further testing we can run DDR at 400MHz so update the timings again. Tested-by: Koen Kooi <koen(a)dominion.thruhere.net> Signed-off-by: Tom Rini <trini(a)ti.com> --- arch/arm/include/asm/arch-am33xx/ddr_defs.h | 20 ++++++++++---------- board/ti/am335x/board.c | 2 +- 2 files changed, 11 insertions(+), 11 deletions(-) diff --git a/arch/arm/include/asm/arch-am33xx/ddr_defs.h b/arch/arm/include/asm/arch-am33xx/ddr_defs.h index 260cc34..914df01 100644 --- a/arch/arm/include/asm/arch-am33xx/ddr_defs.h +++ b/arch/arm/include/asm/arch-am33xx/ddr_defs.h @@ -84,19 +84,19 @@ #define MT41J256M8HX15E_IOCTRL_VALUE 0x18B /* Micron MT41K256M16HA-125E */ -#define MT41K256M16HA125E_EMIF_READ_LATENCY 0x100006 -#define MT41K256M16HA125E_EMIF_TIM1 0x0888A39B -#define MT41K256M16HA125E_EMIF_TIM2 0x26517FDA -#define MT41K256M16HA125E_EMIF_TIM3 0x501F84EF -#define MT41K256M16HA125E_EMIF_SDCFG 0x61C04BB2 -#define MT41K256M16HA125E_EMIF_SDREF 0x0000093B +#define MT41K256M16HA125E_EMIF_READ_LATENCY 0x100007 +#define MT41K256M16HA125E_EMIF_TIM1 0x0AAAD4DB +#define MT41K256M16HA125E_EMIF_TIM2 0x26437FDA +#define MT41K256M16HA125E_EMIF_TIM3 0x501F83FF +#define MT41K256M16HA125E_EMIF_SDCFG 0x61C052B2 +#define MT41K256M16HA125E_EMIF_SDREF 0xC30 #define MT41K256M16HA125E_ZQ_CFG 0x50074BE4 #define MT41K256M16HA125E_DLL_LOCK_DIFF 0x1 -#define MT41K256M16HA125E_RATIO 0x40 +#define MT41K256M16HA125E_RATIO 0x80 #define MT41K256M16HA125E_INVERT_CLKOUT 0x0 -#define MT41K256M16HA125E_RD_DQS 0x3C -#define MT41K256M16HA125E_WR_DQS 0x45 -#define MT41K256M16HA125E_PHY_WR_DATA 0x7F +#define MT41K256M16HA125E_RD_DQS 0x3A +#define MT41K256M16HA125E_WR_DQS 0x42 +#define MT41K256M16HA125E_PHY_WR_DATA 0x7E #define MT41K256M16HA125E_PHY_FIFO_WE 0x9B #define MT41K256M16HA125E_IOCTRL_VALUE 0x18B diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c index 12620bb..b371376 100644 --- a/board/ti/am335x/board.c +++ b/board/ti/am335x/board.c @@ -379,7 +379,7 @@ void s_init(void) config_ddr(303, MT41J128MJT125_IOCTRL_VALUE, &ddr3_data, &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0); else if (board_is_bone_lt()) - config_ddr(303, MT41K256M16HA125E_IOCTRL_VALUE, + config_ddr(400, MT41K256M16HA125E_IOCTRL_VALUE, &ddr3_beagleblack_data, &ddr3_beagleblack_cmd_ctrl_data, &ddr3_beagleblack_emif_reg_data, 0); -- 1.7.9.5

1 1

[U-Boot] [PATCH 1/5][v2] powerpc/mpc85xx:No NOR boot, do not compile IFC errata A003399
by Prabhakar Kushwaha 10 Apr '13

10 Apr '13

IFC errata A003399 is valid for IFC NOR boot i.e.if no on-board NOR flash or no NOR boot, do not compile its workaround. Signed-off-by: Prabhakar Kushwaha <prabhakar(a)freescale.com> --- Based upon git://git.denx.de/u-boot.git branch master Changes for v2: - Add CONFIG_A003399_NOR_WORKAROUND for errata workaround - Add CONFIG_A003399_NOR_WORKAROUND in README README | 4 ++++ arch/powerpc/cpu/mpc85xx/cpu_init_early.c | 9 ++++++--- arch/powerpc/cpu/mpc8xxx/fsl_ifc.c | 2 +- 3 files changed, 11 insertions(+), 4 deletions(-) diff --git a/README b/README index 7f2506a..c4ad69d 100644 --- a/README +++ b/README @@ -414,6 +414,10 @@ The following options need to be configured: See Freescale App Note 4493 for more information about this erratum. + CONFIG_A003399_NOR_WORKAROUND + Enables a workaround for IFC erratum A003399. It is only + requred during NOR boot. + CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY This is the value to write into CCSR offset 0x18600 diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init_early.c b/arch/powerpc/cpu/mpc85xx/cpu_init_early.c index dacfdd1..3a4bfc5 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init_early.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init_early.c @@ -25,7 +25,8 @@ DECLARE_GLOBAL_DATA_PTR; -#if defined(CONFIG_SYS_FSL_ERRATUM_IFC_A003399) && !defined(CONFIG_SYS_RAMBOOT) +#if defined(CONFIG_SYS_FSL_ERRATUM_IFC_A003399)\ + && defined(CONFIG_A003399_NOR_WORKAROUND) void setup_ifc(void) { struct fsl_ifc *ifc_regs = (void *)CONFIG_SYS_IFC_ADDR; @@ -99,7 +100,8 @@ void cpu_init_early_f(void) #ifdef CONFIG_SYS_FSL_ERRATUM_P1010_A003549 ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); #endif -#if defined(CONFIG_SYS_FSL_ERRATUM_IFC_A003399) && !defined(CONFIG_SYS_RAMBOOT) +#if defined(CONFIG_SYS_FSL_ERRATUM_IFC_A003399)\ + && defined(CONFIG_A003399_NOR_WORKAROUND) ccsr_l2cache_t *l2cache = (void *)CONFIG_SYS_MPC85xx_L2_ADDR; u32 *dst, *src; void (*setup_ifc_sram)(void); @@ -138,7 +140,8 @@ void cpu_init_early_f(void) * Work Around for IFC Erratum A003399, issue will hit only when execution * from NOR Flash */ -#if defined(CONFIG_SYS_FSL_ERRATUM_IFC_A003399) && !defined(CONFIG_SYS_RAMBOOT) +#if defined(CONFIG_SYS_FSL_ERRATUM_IFC_A003399)\ + && defined(CONFIG_A003399_NOR_WORKAROUND) #define SRAM_BASE_ADDR (0x00000000) /* TLB for SRAM */ mas0 = MAS0_TLBSEL(1) | MAS0_ESEL(9); diff --git a/arch/powerpc/cpu/mpc8xxx/fsl_ifc.c b/arch/powerpc/cpu/mpc8xxx/fsl_ifc.c index 56b319f..959a0e2 100644 --- a/arch/powerpc/cpu/mpc8xxx/fsl_ifc.c +++ b/arch/powerpc/cpu/mpc8xxx/fsl_ifc.c @@ -43,7 +43,7 @@ void init_early_memctl_regs(void) set_ifc_ftim(IFC_CS0, IFC_FTIM2, CONFIG_SYS_CS0_FTIM2); set_ifc_ftim(IFC_CS0, IFC_FTIM3, CONFIG_SYS_CS0_FTIM3); -#if !defined(CONFIG_SYS_FSL_ERRATUM_IFC_A003399) || defined(CONFIG_SYS_RAMBOOT) +#ifndef CONFIG_A003399_NOR_WORKAROUND #ifdef CONFIG_SYS_CSPR0_EXT set_ifc_cspr_ext(IFC_CS0, CONFIG_SYS_CSPR0_EXT); #endif -- 1.7.9.5

2 7

[U-Boot] [PATCH] omap5_uevm: Correct to 2MiB aligned partitions on eMMC
by Tom Rini 10 Apr '13

10 Apr '13

This has a 2MiB erase block size eMMC, so make sure we align on that for best possible performance. Signed-off-by: Tom Rini <trini(a)ti.com> --- include/configs/omap5_uevm.h | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/include/configs/omap5_uevm.h b/include/configs/omap5_uevm.h index e490523..240fdfc 100644 --- a/include/configs/omap5_uevm.h +++ b/include/configs/omap5_uevm.h @@ -31,8 +31,7 @@ /* Define the default GPT table for eMMC */ #define PARTS_DEFAULT \ "uuid_disk=${uuid_gpt_disk};" \ - "name=u-boot,size=1792KiB,uuid=${uuid_gpt_u-boot};" \ - "name=rootfs,size=-,uuid=${uuid_gpt_rootfs}" + "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}" #include <configs/omap5_common.h> -- 1.7.9.5

1 1

[U-Boot] [PATCH] am335x/ti814x: Correct MMC_BOOT_DEVICES_START/END
by Tom Rini 10 Apr '13

10 Apr '13

Given that on TI814x we have MMC1/2 swapped, we also need to swap them in MMC_BOOT_DEVICES_START/END Reported-by: Peter Korsgaard <jacmet(a)sunsite.dk> Signed-off-by: Tom Rini <trini(a)ti.com> --- arch/arm/include/asm/arch-am33xx/spl.h | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/include/asm/arch-am33xx/spl.h b/arch/arm/include/asm/arch-am33xx/spl.h index 14a2c7c..4c23b27 100644 --- a/arch/arm/include/asm/arch-am33xx/spl.h +++ b/arch/arm/include/asm/arch-am33xx/spl.h @@ -38,6 +38,11 @@ #define BOOT_DEVICE_CPGMAC 70 #define BOOT_DEVICE_MMC2_2 0xFF +#ifdef CONFIG_AM33XX #define MMC_BOOT_DEVICES_START BOOT_DEVICE_MMC1 #define MMC_BOOT_DEVICES_END BOOT_DEVICE_MMC2 +#elif defined(CONFIG_TI814X) +#define MMC_BOOT_DEVICES_START BOOT_DEVICE_MMC2 +#define MMC_BOOT_DEVICES_END BOOT_DEVICE_MMC1 +#endif #endif -- 1.7.9.5

1 1

[U-Boot] [PATCH] OMAP4: Fix bug in omap4460_volts struct
by Lubomir Popov 10 Apr '13

10 Apr '13

The omap4460_volts struct was incorrectly referencing tps62361 instead of twl6030 as PMIC for the core and mm voltages (the tps is used for mpu supply only). This shall lead to bad OPP settings while booting kernel. Fixing it. Fix some comments as well. Signed-off-by: Lubomir Popov <lpopov(a)mm-sol.com> --- This patch is separated from the OMAP4470/TWL6032 support series because it fixes an existing bug. arch/arm/cpu/armv7/omap4/hw_data.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm/cpu/armv7/omap4/hw_data.c b/arch/arm/cpu/armv7/omap4/hw_data.c index 7551b98..04977b4 100644 --- a/arch/arm/cpu/armv7/omap4/hw_data.c +++ b/arch/arm/cpu/armv7/omap4/hw_data.c @@ -216,14 +216,14 @@ struct dplls omap4460_dplls = { struct pmic_data twl6030_4430es1 = { .base_offset = PHOENIX_SMPS_BASE_VOLT_STD_MODE_UV, - .step = 12660, /* 10 mV represented in uV */ + .step = 12660, /* 12.66 mV represented in uV */ /* The code starts at 1 not 0 */ .start_code = 1, }; struct pmic_data twl6030 = { .base_offset = PHOENIX_SMPS_BASE_VOLT_STD_MODE_WITH_OFFSET_UV, - .step = 12660, /* 10 mV represented in uV */ + .step = 12660, /* 12.66 mV represented in uV */ /* The code starts at 1 not 0 */ .start_code = 1, }; @@ -271,11 +271,11 @@ struct vcores_data omap4460_volts = { .core.value = 1200, .core.addr = SMPS_REG_ADDR_VCORE1, - .core.pmic = &tps62361, + .core.pmic = &twl6030, .mm.value = 1200, .mm.addr = SMPS_REG_ADDR_VCORE2, - .mm.pmic = &tps62361, + .mm.pmic = &twl6030, }; /* -- 1.7.9.6 (Apple Git-31.1)

2 1

[U-Boot] [PATCH 0/4] omap2420-h4: Fix u-boot support for board
by Jon Hunter 10 Apr '13

10 Apr '13

Currently, u-boot support for the omap2420-h4 board is broken and u-boot is not booting when program into flash. Fix u-boot support for this board. Jon Hunter (4): omap2420-h4: Fix DRAM initialisation omap2420-h4: Fix booting from NOR flash omap2420-h4: Add device tree support omap2420-h4: Fix get_timer() and CONFIG_SYS_HZ arch/arm/cpu/arm1136/omap24xx/timer.c | 8 ++++++-- arch/arm/include/asm/arch-omap24xx/omap2420.h | 6 +++--- board/ti/omap2420h4/config.mk | 4 ++-- board/ti/omap2420h4/mem.c | 13 ------------- board/ti/omap2420h4/omap2420h4.c | 24 ++++++++++++++++++------ include/configs/omap2420h4.h | 5 +++-- 6 files changed, 32 insertions(+), 28 deletions(-) -- 1.7.10.4

2 7

[U-Boot] [PATCH v2 3/3] mx6sl: Add initial support for mx6slevk board
by festevam＠gmail.com 10 Apr '13

10 Apr '13

From: Fabio Estevam <fabio.estevam(a)freescale.com> mx6slevk board is a development board from Freescale based on the mx6 solo-lite processor. For details about mx6slevk, please refer to: http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=IMX6SLEVK&pa… Signed-off-by: Fabio Estevam <fabio.estevam(a)freescale.com> --- Changes since v2: - Total RAM is 1GB, not 512MB Changes since v1: - None MAINTAINERS | 1 + board/freescale/mx6slevk/Makefile | 28 +++++ board/freescale/mx6slevk/imximage.cfg | 118 ++++++++++++++++++++ board/freescale/mx6slevk/mx6slevk.c | 102 ++++++++++++++++++ boards.cfg | 1 + include/configs/mx6slevk.h | 189 +++++++++++++++++++++++++++++++++ 6 files changed, 439 insertions(+) create mode 100644 board/freescale/mx6slevk/Makefile create mode 100644 board/freescale/mx6slevk/imximage.cfg create mode 100644 board/freescale/mx6slevk/mx6slevk.c create mode 100644 include/configs/mx6slevk.h diff --git a/MAINTAINERS b/MAINTAINERS index 0f19078..723a316 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -665,6 +665,7 @@ Fabio Estevam <fabio.estevam(a)freescale.com> mx6qsabresd i.MX6Q mx6qsabreauto i.MX6Q wandboard i.MX6DL/S + mx6slevk i.MX6SL Daniel Gorsulowski <daniel.gorsulowski(a)esd.eu> diff --git a/board/freescale/mx6slevk/Makefile b/board/freescale/mx6slevk/Makefile new file mode 100644 index 0000000..43af351 --- /dev/null +++ b/board/freescale/mx6slevk/Makefile @@ -0,0 +1,28 @@ +# (C) Copyright 2013 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := mx6slevk.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/mx6slevk/imximage.cfg b/board/freescale/mx6slevk/imximage.cfg new file mode 100644 index 0000000..df39a16 --- /dev/null +++ b/board/freescale/mx6slevk/imximage.cfg @@ -0,0 +1,118 @@ +/* + * Copyright (C) 2013 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License or (at your option) any later version. + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ + +/* image version */ + +IMAGE_VERSION 2 + +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ + +BOOT_FROM sd + +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ +DATA 4 0x020c4018 0x00260324 + +DATA 4 0x020c4068 0xffffffff +DATA 4 0x020c406c 0xffffffff +DATA 4 0x020c4070 0xffffffff +DATA 4 0x020c4074 0xffffffff +DATA 4 0x020c4078 0xffffffff +DATA 4 0x020c407c 0xffffffff +DATA 4 0x020c4080 0xffffffff + +DATA 4 0x020e0344 0x00003030 +DATA 4 0x020e0348 0x00003030 +DATA 4 0x020e034c 0x00003030 +DATA 4 0x020e0350 0x00003030 +DATA 4 0x020e030c 0x00000030 +DATA 4 0x020e0310 0x00000030 +DATA 4 0x020e0314 0x00000030 +DATA 4 0x020e0318 0x00000030 +DATA 4 0x020e0300 0x00000030 +DATA 4 0x020e031c 0x00000030 +DATA 4 0x020e0338 0x00000028 +DATA 4 0x020e0320 0x00000030 +DATA 4 0x020e032c 0x00000000 +DATA 4 0x020e033c 0x00000008 +DATA 4 0x020e0340 0x00000008 +DATA 4 0x020e05c4 0x00000030 +DATA 4 0x020e05cc 0x00000030 +DATA 4 0x020e05d4 0x00000030 +DATA 4 0x020e05d8 0x00000030 +DATA 4 0x020e05ac 0x00000030 +DATA 4 0x020e05c8 0x00000030 +DATA 4 0x020e05b0 0x00020000 +DATA 4 0x020e05b4 0x00000000 +DATA 4 0x020e05c0 0x00020000 +DATA 4 0x020e05d0 0x00080000 + +DATA 4 0x021b001c 0x00008000 +DATA 4 0x021b085c 0x1b4700c7 +DATA 4 0x021b0800 0xa1390003 +DATA 4 0x021b0890 0x00300000 +DATA 4 0x021b08b8 0x00000800 +DATA 4 0x021b081c 0x33333333 +DATA 4 0x021b0820 0x33333333 +DATA 4 0x021b0824 0x33333333 +DATA 4 0x021b0828 0x33333333 +DATA 4 0x021b082c 0xf3333333 +DATA 4 0x021b0830 0xf3333333 +DATA 4 0x021b0834 0xf3333333 +DATA 4 0x021b0838 0xf3333333 +DATA 4 0x021b0848 0x4241444a +DATA 4 0x021b0850 0x3030312b +DATA 4 0x021b083c 0x20000000 +DATA 4 0x021b0840 0x00000000 +DATA 4 0x021b08c0 0x24911492 +DATA 4 0x021b08b8 0x00000800 +DATA 4 0x021b000c 0x33374133 +DATA 4 0x021b0004 0x00020024 +DATA 4 0x021b0010 0x00100A82 +DATA 4 0x021b0014 0x00000093 +DATA 4 0x021b0018 0x00001688 +DATA 4 0x021b002c 0x0f9f26d2 +DATA 4 0x021b0030 0x0000020e +DATA 4 0x021b0038 0x00190778 +DATA 4 0x021b0008 0x00000000 +DATA 4 0x021b0040 0x0000004f +DATA 4 0x021b0000 0xc3110000 +DATA 4 0x021b001c 0x003f8030 +DATA 4 0x021b001c 0xff0a8030 +DATA 4 0x021b001c 0x82018030 +DATA 4 0x021b001c 0x04028030 +DATA 4 0x021b001c 0x02038030 +DATA 4 0x021b001c 0xff0a8038 +DATA 4 0x021b001c 0x82018038 +DATA 4 0x021b001c 0x04028038 +DATA 4 0x021b001c 0x02038038 +DATA 4 0x021b0800 0xa1310003 +DATA 4 0x021b0020 0x00001800 +DATA 4 0x021b0818 0x00000000 +DATA 4 0x021b08b8 0x00000800 +DATA 4 0x021b0004 0x00025564 +DATA 4 0x021b0404 0x00011006 +DATA 4 0x021b001c 0x00000000 diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c new file mode 100644 index 0000000..fc6353e --- /dev/null +++ b/board/freescale/mx6slevk/mx6slevk.c @@ -0,0 +1,102 @@ +/* + * Copyright (C) 2013 Freescale Semiconductor, Inc. + * + * Author: Fabio Estevam <fabio.estevam(a)freescale.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#include <asm/arch/clock.h> +#include <asm/arch/iomux.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/mx6-pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/gpio.h> +#include <asm/imx-common/iomux-v3.h> +#include <asm/io.h> +#include <asm/sizes.h> +#include <common.h> +#include <fsl_esdhc.h> +#include <mmc.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +int dram_init(void) +{ + gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); + + return 0; +} + +static iomux_v3_cfg_t const uart1_pads[] = { + MX6_PAD_UART1_TXD__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_UART1_RXD__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static iomux_v3_cfg_t const usdhc2_pads[] = { + MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT0__USDHC2_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT1__USDHC2_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT2__USDHC2_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), +}; + +static void setup_iomux_uart(void) +{ + imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); +} + +static struct fsl_esdhc_cfg usdhc_cfg[1] = { + {USDHC2_BASE_ADDR}, +}; + +int board_mmc_getcd(struct mmc *mmc) +{ + return 1; /* Assume boot SD always present */ +} + +int board_mmc_init(bd_t *bis) +{ + imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); + + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); + return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); +} + +int board_early_init_f(void) +{ + setup_iomux_uart(); + return 0; +} + +int board_init(void) +{ + /* address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + + return 0; +} + +u32 get_board_rev(void) +{ + return get_cpu_rev(); +} + +int checkboard(void) +{ + puts("Board: MX6SLEVK\n"); + + return 0; +} diff --git a/boards.cfg b/boards.cfg index 7725a15..9e213ad 100644 --- a/boards.cfg +++ b/boards.cfg @@ -257,6 +257,7 @@ mx6qarm2 arm armv7 mx6qarm2 freesca mx6qsabreauto arm armv7 mx6qsabreauto freescale mx6 mx6qsabreauto:IMX_CONFIG=board/freescale/mx6qsabreauto/imximage.cfg mx6qsabrelite arm armv7 mx6qsabrelite freescale mx6 mx6qsabrelite:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg mx6qsabresd arm armv7 mx6qsabresd freescale mx6 mx6qsabresd:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg +mx6slevk arm armv7 mx6slevk freescale mx6 mx6slevk:IMX_CONFIG=board/freescale/mx6slevk/imximage.cfg,MX6SL eco5pk arm armv7 eco5pk 8dtech omap3 nitrogen6dl arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL,DDR_MB=1024 nitrogen6dl2g arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl2g.cfg,MX6DL,DDR_MB=2048 diff --git a/include/configs/mx6slevk.h b/include/configs/mx6slevk.h new file mode 100644 index 0000000..67b63f4 --- /dev/null +++ b/include/configs/mx6slevk.h @@ -0,0 +1,189 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * Configuration settings for the Freescale i.MX6SL EVK board. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/arch/imx-regs.h> +#include <asm/sizes.h> + +#define CONFIG_MX6 +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#define MACH_TYPE_MX6SLEVK 4307 +#define CONFIG_MACH_TYPE MACH_TYPE_MX6SLEVK + +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_REVISION_TAG + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (3 * SZ_1M) + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_MXC_GPIO + +#define CONFIG_MXC_UART +#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR + +/* MMC Configs */ +#define CONFIG_FSL_ESDHC +#define CONFIG_FSL_USDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR 0 + +#define CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 + +/* Command definition */ +#include <config_cmd_default.h> + +#undef CONFIG_CMD_IMLS + +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_LOADADDR 0x80800000 +#define CONFIG_SYS_TEXT_BASE 0x87800000 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "script=boot.scr\0" \ + "uimage=uImage\0" \ + "console=ttymxc0\0" \ + "fdt_high=0xffffffff\0" \ + "initrd_high=0xffffffff\0" \ + "fdt_file=imx6sl-evk.dtb\0" \ + "fdt_addr=0x81000000\0" \ + "boot_fdt=try\0" \ + "ip_dyn=yes\0" \ + "mmcdev=0\0" \ + "mmcpart=2\0" \ + "mmcroot=/dev/mmcblk0p3 rootwait rw\0" \ + "mmcargs=setenv bootargs console=${console},${baudrate} " \ + "root=${mmcroot}\0" \ + "loadbootscript=" \ + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if run loadfdt; then " \ + "bootm ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootm; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootm; " \ + "fi;\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${uimage}; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ + "bootm ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootm; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootm; " \ + "fi;\0" + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev};" \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loaduimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else run netboot; fi" + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT "=> " +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 256 + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_MEMTEST_START 0x80000000 +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + SZ_512M) + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_CMDLINE_EDITING +#define CONFIG_STACKSIZE SZ_128K + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR +#define PHYS_SDRAM_SIZE SZ_1G + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* FLASH and environment organization */ +#define CONFIG_SYS_NO_FLASH + +#define CONFIG_ENV_OFFSET (6 * SZ_64K) +#define CONFIG_ENV_SIZE SZ_8K +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 + +#define CONFIG_OF_LIBFDT +#define CONFIG_CMD_BOOTZ + +#ifndef CONFIG_SYS_DCACHE_OFF +#define CONFIG_CMD_CACHE +#endif + +#endif /* __CONFIG_H */ -- 1.7.9.5

1 0

[U-Boot] [PATCH v3 2/3] mx6: Add solo-lite variant support
by festevam＠gmail.com 10 Apr '13

10 Apr '13

From: Fabio Estevam <fabio.estevam(a)freescale.com> mx6 solo-lite is another member of the mx6 series. For more information about mx6 solo-lite, please visit: http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=i.MX6SL&node… Signed-off-by: Fabio Estevam <fabio.estevam(a)freescale.com> --- Changes since v2: - None Changes since v1: - None arch/arm/cpu/armv7/mx6/clock.c | 38 ++++++++++++++++- arch/arm/include/asm/arch-mx6/crm_regs.h | 5 +++ arch/arm/include/asm/arch-mx6/imx-regs.h | 63 +++++++++++++++++++++++++++- arch/arm/include/asm/arch-mx6/mx6-pins.h | 4 ++ arch/arm/include/asm/arch-mx6/mx6sl_pins.h | 25 +++++++++++ 5 files changed, 132 insertions(+), 3 deletions(-) create mode 100644 arch/arm/include/asm/arch-mx6/mx6sl_pins.h diff --git a/arch/arm/cpu/armv7/mx6/clock.c b/arch/arm/cpu/armv7/mx6/clock.c index a50db70..8cba4fd 100644 --- a/arch/arm/cpu/armv7/mx6/clock.c +++ b/arch/arm/cpu/armv7/mx6/clock.c @@ -186,12 +186,16 @@ static u32 get_ipg_per_clk(void) static u32 get_uart_clk(void) { u32 reg, uart_podf; - + u32 freq = PLL3_80M; reg = __raw_readl(&imx_ccm->cscdr1); +#ifdef CONFIG_MX6SL + if (reg & MXC_CCM_CSCDR1_UART_CLK_SEL) + freq = MXC_HCLK; +#endif reg &= MXC_CCM_CSCDR1_UART_CLK_PODF_MASK; uart_podf = reg >> MXC_CCM_CSCDR1_UART_CLK_PODF_OFFSET; - return PLL3_80M / (uart_podf + 1); + return freq / (uart_podf + 1); } static u32 get_cspi_clk(void) @@ -252,6 +256,35 @@ static u32 get_emi_slow_clk(void) return root_freq / (emi_slow_pof + 1); } +#ifdef CONFIG_MX6SL +static u32 get_mmdc_ch0_clk(void) +{ + u32 cbcmr = __raw_readl(&imx_ccm->cbcmr); + u32 cbcdr = __raw_readl(&imx_ccm->cbcdr); + u32 freq, podf; + + podf = (cbcdr & MXC_CCM_CBCDR_MMDC_CH1_PODF_MASK) \ + >> MXC_CCM_CBCDR_MMDC_CH1_PODF_OFFSET; + + switch ((cbcmr & MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_MASK) >> + MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_OFFSET) { + case 0: + freq = decode_pll(PLL_BUS, MXC_HCLK); + break; + case 1: + freq = PLL2_PFD2_FREQ; + break; + case 2: + freq = PLL2_PFD0_FREQ; + break; + case 3: + freq = PLL2_PFD2_DIV_FREQ; + } + + return freq / (podf + 1); + +} +#else static u32 get_mmdc_ch0_clk(void) { u32 cbcdr = __raw_readl(&imx_ccm->cbcdr); @@ -260,6 +293,7 @@ static u32 get_mmdc_ch0_clk(void) return get_periph_clk() / (mmdc_ch0_podf + 1); } +#endif static u32 get_usdhc_clk(u32 port) { diff --git a/arch/arm/include/asm/arch-mx6/crm_regs.h b/arch/arm/include/asm/arch-mx6/crm_regs.h index 7676457..b1ed62f 100644 --- a/arch/arm/include/asm/arch-mx6/crm_regs.h +++ b/arch/arm/include/asm/arch-mx6/crm_regs.h @@ -244,7 +244,12 @@ struct mxc_ccm_reg { #define MXC_CCM_CSCDR1_USBOH3_CLK_PRED_MASK (0x7 << 8) #define MXC_CCM_CSCDR1_USBOH3_CLK_PODF_OFFSET 6 #define MXC_CCM_CSCDR1_USBOH3_CLK_PODF_MASK (0x3 << 6) +#ifdef CONFIG_MX6SL +#define MXC_CCM_CSCDR1_UART_CLK_PODF_MASK 0x1F +#define MXC_CCM_CSCDR1_UART_CLK_SEL (1 << 6) +#else #define MXC_CCM_CSCDR1_UART_CLK_PODF_MASK 0x3F +#endif #define MXC_CCM_CSCDR1_UART_CLK_PODF_OFFSET 0 /* Define the bits in register CS1CDR */ diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h index eaa7439..2d8fe69 100644 --- a/arch/arm/include/asm/arch-mx6/imx-regs.h +++ b/arch/arm/include/asm/arch-mx6/imx-regs.h @@ -25,6 +25,13 @@ #define ROMCP_ARB_BASE_ADDR 0x00000000 #define ROMCP_ARB_END_ADDR 0x000FFFFF + +#ifdef CONFIG_MX6SL +#define GPU_2D_ARB_BASE_ADDR 0x02200000 +#define GPU_2D_ARB_END_ADDR 0x02203FFF +#define OPENVG_ARB_BASE_ADDR 0x02204000 +#define OPENVG_ARB_END_ADDR 0x02207FFF +#else #define CAAM_ARB_BASE_ADDR 0x00100000 #define CAAM_ARB_END_ADDR 0x00103FFF #define APBH_DMA_ARB_BASE_ADDR 0x00110000 @@ -37,9 +44,14 @@ #define GPU_2D_ARB_END_ADDR 0x00137FFF #define DTCP_ARB_BASE_ADDR 0x00138000 #define DTCP_ARB_END_ADDR 0x0013BFFF - +#endif /* CONFIG_MX6SL */ /* GPV - PL301 configuration ports */ +#ifdef CONFIG_MX6SL +#define GPV2_BASE_ADDR 0x00D00000 +#else #define GPV2_BASE_ADDR 0x00200000 +#endif + #define GPV3_BASE_ADDR 0x00300000 #define GPV4_BASE_ADDR 0x00800000 #define IRAM_BASE_ADDR 0x00900000 @@ -70,10 +82,17 @@ #define WEIM_ARB_BASE_ADDR 0x08000000 #define WEIM_ARB_END_ADDR 0x0FFFFFFF +#ifdef CONFIG_MX6SL +#define MMDC0_ARB_BASE_ADDR 0x80000000 +#define MMDC0_ARB_END_ADDR 0xFFFFFFFF +#define MMDC1_ARB_BASE_ADDR 0xC0000000 +#define MMDC1_ARB_END_ADDR 0xFFFFFFFF +#else #define MMDC0_ARB_BASE_ADDR 0x10000000 #define MMDC0_ARB_END_ADDR 0x7FFFFFFF #define MMDC1_ARB_BASE_ADDR 0x80000000 #define MMDC1_ARB_END_ADDR 0xFFFFFFFF +#endif #define IPU_SOC_BASE_ADDR IPU1_ARB_BASE_ADDR #define IPU_SOC_OFFSET 0x00200000 @@ -89,6 +108,16 @@ #define ECSPI2_BASE_ADDR (ATZ1_BASE_ADDR + 0x0C000) #define ECSPI3_BASE_ADDR (ATZ1_BASE_ADDR + 0x10000) #define ECSPI4_BASE_ADDR (ATZ1_BASE_ADDR + 0x14000) +#ifdef CONFIG_MX6SL +#define UART5_IPS_BASE_ADDR (ATZ1_BASE_ADDR + 0x18000) +#define UART1_IPS_BASE_ADDR (ATZ1_BASE_ADDR + 0x20000) +#define UART2_IPS_BASE_ADDR (ATZ1_BASE_ADDR + 0x24000) +#define SSI1_IPS_BASE_ADDR (ATZ1_BASE_ADDR + 0x28000) +#define SSI2_IPS_BASE_ADDR (ATZ1_BASE_ADDR + 0x2C000) +#define SSI3_IPS_BASE_ADDR (ATZ1_BASE_ADDR + 0x30000) +#define UART3_IPS_BASE_ADDR (ATZ1_BASE_ADDR + 0x34000) +#define UART4_IPS_BASE_ADDR (ATZ1_BASE_ADDR + 0x38000) +#else #define ECSPI5_BASE_ADDR (ATZ1_BASE_ADDR + 0x18000) #define UART1_BASE (ATZ1_BASE_ADDR + 0x20000) #define ESAI1_BASE_ADDR (ATZ1_BASE_ADDR + 0x24000) @@ -96,6 +125,8 @@ #define SSI2_BASE_ADDR (ATZ1_BASE_ADDR + 0x2C000) #define SSI3_BASE_ADDR (ATZ1_BASE_ADDR + 0x30000) #define ASRC_BASE_ADDR (ATZ1_BASE_ADDR + 0x34000) +#endif + #define SPBA_BASE_ADDR (ATZ1_BASE_ADDR + 0x3C000) #define VPU_BASE_ADDR (ATZ1_BASE_ADDR + 0x40000) #define AIPS1_ON_BASE_ADDR (ATZ1_BASE_ADDR + 0x7C000) @@ -128,18 +159,35 @@ #define SRC_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x58000) #define GPC_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x5C000) #define IOMUXC_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x60000) +#ifdef CONFIG_MX6SL +#define CSI_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x64000) +#define SIPIX_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x68000) +#define SDMA_PORT_HOST_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x6C000) +#else #define DCIC1_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x64000) #define DCIC2_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x68000) #define DMA_REQ_PORT_HOST_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x6C000) +#endif #define AIPS2_ON_BASE_ADDR (ATZ2_BASE_ADDR + 0x7C000) #define AIPS2_OFF_BASE_ADDR (ATZ2_BASE_ADDR + 0x80000) #define CAAM_BASE_ADDR (ATZ2_BASE_ADDR) #define ARM_BASE_ADDR (ATZ2_BASE_ADDR + 0x40000) +#ifdef CONFIG_MX6SL +#define USBO2H_PL301_IPS_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x0000) +#define USBO2H_USB_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x4000) +#else #define USBOH3_PL301_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x0000) #define USBOH3_USB_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x4000) +#endif + #define ENET_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x8000) +#ifdef CONFIG_MX6SL +#define MSHC_IPS_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0xC000) +#else #define MLB_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0xC000) +#endif + #define USDHC1_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x10000) #define USDHC2_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x14000) #define USDHC3_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x18000) @@ -149,7 +197,12 @@ #define I2C3_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x28000) #define ROMCP_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x2C000) #define MMDC_P0_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x30000) +#ifdef CONFIG_MX6SL +#define RNGB_IPS_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x34000) +#else #define MMDC_P1_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x34000) +#endif + #define WEIM_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x38000) #define OCOTP_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x3C000) #define CSU_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x40000) @@ -364,12 +417,20 @@ struct cspi_regs { #define MXC_CSPICON_POL 4 #define MXC_CSPICON_PHA 0 #define MXC_CSPICON_SSPOL 12 +#ifdef CONFIG_MX6SL +#define MXC_SPI_BASE_ADDRESSES \ + ECSPI1_BASE_ADDR, \ + ECSPI2_BASE_ADDR, \ + ECSPI3_BASE_ADDR, \ + ECSPI4_BASE_ADDR +#else #define MXC_SPI_BASE_ADDRESSES \ ECSPI1_BASE_ADDR, \ ECSPI2_BASE_ADDR, \ ECSPI3_BASE_ADDR, \ ECSPI4_BASE_ADDR, \ ECSPI5_BASE_ADDR +#endif struct iim_regs { u32 ctrl; diff --git a/arch/arm/include/asm/arch-mx6/mx6-pins.h b/arch/arm/include/asm/arch-mx6/mx6-pins.h index 63f4856..ce865a6 100644 --- a/arch/arm/include/asm/arch-mx6/mx6-pins.h +++ b/arch/arm/include/asm/arch-mx6/mx6-pins.h @@ -24,7 +24,11 @@ #if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S) #include "mx6dl_pins.h" #else +#if defined(CONFIG_MX6SL) +#include "mx6sl_pins.h" +#else #error "Please select cpu" +#endif /* CONFIG_MX6SL */ #endif /* CONFIG_MX6DL or CONFIG_MX6S */ #endif /* CONFIG_MX6Q */ diff --git a/arch/arm/include/asm/arch-mx6/mx6sl_pins.h b/arch/arm/include/asm/arch-mx6/mx6sl_pins.h new file mode 100644 index 0000000..bfe4f00 --- /dev/null +++ b/arch/arm/include/asm/arch-mx6/mx6sl_pins.h @@ -0,0 +1,25 @@ +/* + * Copyright (C) 2013 Freescale Semiconductor, Inc. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __ASM_ARCH_MX6_MX6SL_PINS_H__ +#define __ASM_ARCH_MX6_MX6SL_PINS_H__ + +#include <asm/imx-common/iomux-v3.h> + +enum { + MX6_PAD_SD2_CLK__USDHC2_CLK = IOMUX_PAD(0x055C, 0x0254, 0, 0x0000, 0, 0), + MX6_PAD_SD2_CMD__USDHC2_CMD = IOMUX_PAD(0x0560, 0x0258, 0, 0x0000, 0, 0), + MX6_PAD_SD2_DAT0__USDHC2_DAT0 = IOMUX_PAD(0x0564, 0x025C, 0, 0x0000, 0, 0), + MX6_PAD_SD2_DAT1__USDHC2_DAT1 = IOMUX_PAD(0x0568, 0x0260, 0, 0x0000, 0, 0), + MX6_PAD_SD2_DAT2__USDHC2_DAT2 = IOMUX_PAD(0x056C, 0x0264, 0, 0x0000, 0, 0), + MX6_PAD_SD2_DAT3__USDHC2_DAT3 = IOMUX_PAD(0x0570, 0x0268, 0, 0x0000, 0, 0), + MX6_PAD_UART1_RXD__UART1_RXD = IOMUX_PAD(0x05A0, 0x0298, 0, 0x07FC, 0, 0), + MX6_PAD_UART1_TXD__UART1_TXD = IOMUX_PAD(0x05A4, 0x029C, 0, 0x0000, 0, 0), +}; +#endif /* __ASM_ARCH_MX6_MX6SL_PINS_H__ */ -- 1.7.9.5

1 0