March 2013 - U-Boot

[U-Boot] [PATCH v2 0/7] mtd/st_smi: Add fixes for smi driver
by Vipin Kumar 14 Dec '15

14 Dec '15

Modifications in v2 (Review comments incorporation) - Use setbits_le32 and clrbits_le32 whereever applicable in patch-set - Define smi_mtd_init() routine irrespective of CONFIG_MTD_DEVICE Modifications in v1 - Add MTD support for smi driver - Write to flash in a tight loop - Alphabetically sort the list of devices - Avoid issuing multiple write enable commands Armando Visconti (1): mtd/st_smi: Add support for Micron N25Q128 Flash Vipin Kumar (6): mtd/st_smi: Clear error flags while initiating a fresh write mtd/st_smi: Rearrange the supported devices in alphabetical order mtd/st_smi: Avoid issuing multiple WE commands mtd/st_smi: Write to flash in a tight loop mtd/st_smi: Use page sizes respective to flash mtd/st_smi: Add mtd support for smi drivers/mtd/st_smi.c | 260 ++++++++++++++++++++++++++++++++++++++------- include/linux/mtd/st_smi.h | 1 - 2 files changed, 223 insertions(+), 38 deletions(-) -- 1.8.0

3 14

[U-Boot] [PATCH] FSL SPI read fix.
by Dale Smith 14 Dec '15

14 Dec '15

The fsl spi engine is non functional when reading from a device. This patch fixes it. Note that none of the other spi interfaces parse through the datastream looking for 0x0b bytes. -Dale diff --git a/drivers/spi/fsl_espi.c b/drivers/spi/fsl_espi.c index a1ebd33..737719b 100644 --- a/drivers/spi/fsl_espi.c +++ b/drivers/spi/fsl_espi.c @@ -291,17 +291,10 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *data_out, debug("***spi_xfer:...%08x readed\n", tmpdin); } } - if (data_in) { - memcpy(data_in, buffer + 2 * cmd_len, tran_len); - if (*buffer == 0x0b) { - data_in += tran_len; - data_len -= tran_len; - *(int *)buffer += tran_len; - } - } spi_cs_deactivate(slave); } - + if (data_in) + memcpy(data_in, buffer + rx_offset, len); free(buffer); return 0; }

6 8

[U-Boot] Can't start Linux if U-Boot built with CONFIG_WATCHDOG
by Matthew Lear 26 Aug '15

26 Aug '15

Hello all, I've added watchdog support based on U-Boot (git) for the m68k coldfire mcf54455evb platform. I've fed the patch to the maintainer to help in development. However, I am unable to start my m68k w/MMU coldfire Linux kernel from U-Boot if U-Boot is built with CONFIG_WATCHDOG regardless if the watchdog_enable(), watchdog_reset() and watchdog_disable() functions touch hardware or not. I initially thought this was a problem with enabling the watchdog somehow (ie when Linux started, some hw configuration in the device was getting upset or corrupted etc resulting in the failure), but when I commented out the code from the above functions that actually accesses the hw (ie to enable, kick and disable the watchdog timer hw block), Linux is still unable to start. In fact, I don't think Linux actually gets started! That's the problem. If I rebuild the same U-Boot code base with CONFIG_WATCHDOG undefined, Linux can start just fine. As far as I can tell, there are no functional differences in building U-Boot with or without CONFIG_WATCHDOG enabled when the functions above are stubs and do absolutely nothing at all. If I build U-Boot with debug, what I see is as follows: ## Transferring control to Linux (at address 40020000) ... BIV ...and then the board is dead. I occasionally see something like the following from U-Boot: *** Unexpected exception *** Vector Number: 4 Format: 04 Fault Status: 0 PC: 4fdbfdc8 SR: 00002700 SP: 4fd72a64 D0: 00000004 D1: 000003f9 D2: 4fdb4202 D3: 004fa3da D4: 00000000 D5: 4fdc7c8c D6: 122c0034 D7: 4fd82f76 A0: 4033cb98 A1: 4025aa39 A2: 40020000 A3: 4fdbfdc8 A4: 00000000 A5: 4fdc5800 A6: 4fd72afb *** Please Reset Board! *** The 'BIV' is relevant because in my 2.6.29 kernel src arch/m68k/include/asm/bootinfo_mm.h, BOOTINFOV_MAGIC is defined to be 0x4249561A which is BIV^Z. This ascii text is located in the kernel image header info: >From arch/m68k/coldfire/head.S: .section ".text.head","ax" ENTRY(_stext) bras 1f /* Jump over bootinfo version numbers */ .long BOOTINFOV_MAGIC .long 0 And from U-Boot itself: -> md ${loadaddr} 40010000: 27051956 97342d7d 4a54afd5 00300000 '..V.4-}JT...0.. 40010010: 40020000 40020000 8a006fc1 050c0200 @...@.....o..... 40010020: 4c696e75 78204b65 726e656c 20496d61 Linux Kernel Ima 40010030: 67650000 00000000 00000000 00000000 ge.............. 40010040: 60084249 561a0000 00004ef9 40304000 `.BIV.....N.@0@. I suspect that the failure of starting Linux is caused by some mismatch in data structures (or versions there of) shared/copied between Linux and U-Boot and that this data has somehow changed when U-Boot is built with CONFIG_WATCHDOG #defined. However, I can't find any evidence of this in the U-Boot code base. The bras instruction above must be key and I suspect that this is the area causing the problem. Can anybody offer any advice / explanation of what exactly could be going on and why? I wouldn't have expected that defining CONFIG_WATCHDOG would change anything as fundamental as this. Apologies for the cross-post (U-Boot and m68k kernel dev) but I hope to get opinions/feedback/help from both communities. Any assistance very much appreciated indeed. Many thanks, -- Matt

2 1

[U-Boot] [PATCH 1/3] sf: stmicro: Add support for N25Q32
by Michal Simek 02 Dec '14

02 Dec '14

From: Jagannadha Sutradharudu Teki <jagannadha.sutradharudu-teki(a)xilinx.com> Add support for Numonyx N25Q32 SPI flash. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna(a)xilinx.com> Signed-off-by: Michal Simek <michal.simek(a)xilinx.com> --- drivers/mtd/spi/stmicro.c | 6 ++++++ 1 files changed, 6 insertions(+), 0 deletions(-) diff --git a/drivers/mtd/spi/stmicro.c b/drivers/mtd/spi/stmicro.c index 32df827..09a3d68 100644 --- a/drivers/mtd/spi/stmicro.c +++ b/drivers/mtd/spi/stmicro.c @@ -93,6 +93,12 @@ static const struct stmicro_spi_flash_params stmicro_spi_flash_table[] = { .name = "M25P128", }, { + .id = 0xba16, + .pages_per_sector = 256, + .nr_sectors = 64, + .name = "N25Q32", + }, + { .id = 0xba17, .pages_per_sector = 256, .nr_sectors = 128, -- 1.7.0.4

3 4

[U-Boot] newbie questions regarding some config options.
by Christopher Harvey 22 Aug '14

22 Aug '14

As per the README file: Subscribe to u-boot mailing list; if (clueless) email("Hi, I am new to U-Boot, how do I get started?"); I'm messing around with uboot and QEMU (qemu-system-arm -M realview-pbx-a9 -kernel u-boot.bin), things are going pretty well in the sense that I'm not having too much trouble reading most of the code and creating a new board. I have some questions that I can't figure out by reading the code. What is the CONFIG_SYS_TEXT_BASE variable and how can I figure out what it should be? I randomly set it to 0x0...then tried to debug u-boot under qemu, but when stepping in the start.S file it was instantly clear that it wasn't really working because gdb said the code ran right though the _start: b reset instruction and qemu eventually crashed with the following output: qemu: fatal: Trying to execute code outside RAM or ROM at 0xfeb70cdc R00=00000000 R01=ffff0000 R02=00000000 R03=000108ac R04=ffff0000 R05=ffbedf70 R06=ffff0000 R07=00000010 R08=00001000 R09=ffff0000 R10=000108ac R11=00000000 R12=00001078 R13=ffbedf60 R14=00000960 R15=feb70cdc PSR=600001d3 -ZC- A svc32 Aborted Apart from that everything is pretty clear to me, but I want to make sure I'm getting this points right: Is the environment the set of variables that can be modified with setenv? How can I determine the "size of the environment"? Is it the number of characters including variable names? Also, is there anything special I need to do with gdb to get it to follow relocating code? thanks, -Chris

5 8

[U-Boot] [PATCH v7 00/26] pmic: Redesign PMIC framework to support multiple instances of devices
by Lukasz Majewski 18 Apr '14

18 Apr '14

PMIC framework has been redesigned to support multiple instances of power related devices (e.g. fuel gauge, PMICs, chargers, micro USB IC, battery). Due to that, code at other architectures and boards have been adjusted properly. New power_init_board() method at ./lib/board.c file has been introduced. It is meant to be an architecture dependent function to support advanced power management. Since PMIC framework uses lists internally to link different devices, its initialization must be done just after malloc initialization. Please consider commits from this patch set as the example of advanced power management for a particular HW (Trats board in this case). In the new approach PMICs are selected with their names (e.g. 'pmic dump MAX8997_PMIC') Presented patch set is a first step to change 'pmic' command to more generic (i.e. power) to provide control for multiple devices. Moreover device's battery is treated as an oridinary "power" device (like PMIC). Due to that, framework unification is possible. For even more versalite design, each power device instance can specify its parent. For trats one can build a following scheme (it can de different for other boards): ----------------- --------| BAT |------------ | | | | | ----------------- | | | | \|/ \|/ \|/ ----------- ----------------- --------- |FG | |MUIC | |CHRG | | | | | | | ----------- ----------------- --------- Finally, this patch series also comprises of a "namespace" cleanup - an attempt to rename "pmic" to "power" to better reflect generality of this framework. Test HW: - Exynos4210 Trats development board - Exynos3 (C110) Goni development board Lukasz Majewski (26): pmic:i2c: Handle PMIC I2C transmission comprising of two bytes pmic:i2c: Add I2C sensor byte order (big/little) to PMIC framework pmic:max8997: Switch the MAX8997 PMIC to be used with multibus I2C pmic: Extend PMIC framework to support multiple instances of PMIC devices pmic: Introduce power_init_board() method at ./lib/board.c file pmic: Enable power_board_init() support at TRATS pmic:chrg: Common information about charger and battery (power_chrg.h) pmic: Move pmic related code to ./drivers/power directory pmic: Extend struct pmic to support battery and charger related operations pmic:battery: Support for Trats Battery at PMIC framework pmic:muic: Support for MUIC built into MAX8997 device pmic:fuel-gauge: Support for MAX17042 fuel-gauge pmic:max8997: Function for calculating LDO internal register value arm:trats:pmic: Default PMIC(MAX8997) initialization for Samsung's TRATS board arm:trats:pmic: Enable MUIC (MAX8997) at Samsung's TRATS board arm:trats:pmic: Enable fuel-gauge (MAX17042) at Samsung's TRATS board arm:trats:pmic: Enable battery support at Samsung's TRATS board pmic:max8997: Support for MAX8997 internal charger control arm:trats:pmic: Power consumption reduction state for Samsung's TRATS board arm:trats:pmic: Support for charging battery at Samsung's TRATS board pmic: Extend PMIC framework to support battery related commands power:pmic: Rename ./drivers/power/pmic_* to ./drivers/power/power_* files power:pmic: Rename CONFIG_PMIC* defines to CONFIG_POWER power:pmic: Rename CONFIG_DIALOG_PMIC defines to CONFIG_DIALOG_POWER arm:goni:pmic: Adjust GONI target platform board to new PMIC framework arm:universal_c210:pmic: Adjust C210 Universal target platform board to new PMIC framework Makefile | 5 +- arch/arm/lib/board.c | 8 + board/davedenx/qong/qong.c | 12 +- board/freescale/mx31pdk/mx31pdk.c | 12 +- board/freescale/mx35pdk/mx35pdk.c | 14 +- board/freescale/mx51evk/mx51evk.c | 12 +- board/freescale/mx53evk/mx53evk.c | 12 +- board/freescale/mx53loco/mx53loco.c | 21 +- board/genesi/mx51_efikamx/efikamx.c | 12 +- board/hale/tt01/tt01.c | 14 +- board/samsung/goni/goni.c | 22 +- board/samsung/trats/trats.c | 292 +++++++++++++++++++- board/samsung/universal_c210/universal.c | 27 ++- board/ttcontrol/vision2/vision2.c | 12 +- drivers/misc/Makefile | 7 - drivers/misc/pmic_core.c | 147 ---------- drivers/misc/pmic_i2c.c | 98 ------- drivers/misc/pmic_max8997.c | 43 --- drivers/power/Makefile | 12 +- drivers/power/battery/Makefile | 47 ++++ drivers/power/battery/bat_trats.c | 100 +++++++ drivers/power/fuel_gauge/Makefile | 47 ++++ drivers/power/fuel_gauge/fg_max17042.c | 250 +++++++++++++++++ drivers/power/pmic/Makefile | 49 ++++ drivers/power/pmic/muic_max8997.c | 90 ++++++ drivers/power/pmic/pmic_max8997.c | 123 ++++++++ drivers/{misc => power/pmic}/pmic_max8998.c | 16 +- drivers/power/power_core.c | 232 ++++++++++++++++ .../{misc/pmic_dialog.c => power/power_dialog.c} | 14 +- drivers/{misc/pmic_fsl.c => power/power_fsl.c} | 22 +- drivers/power/power_i2c.c | 125 +++++++++ drivers/{misc/pmic_spi.c => power/power_spi.c} | 4 +- drivers/rtc/mc13xxx-rtc.c | 10 +- include/configs/imx31_litekit.h | 6 +- include/configs/mx31ads.h | 6 +- include/configs/mx31pdk.h | 6 +- include/configs/mx35pdk.h | 6 +- include/configs/mx51_efikamx.h | 6 +- include/configs/mx51evk.h | 6 +- include/configs/mx53evk.h | 6 +- include/configs/mx53loco.h | 8 +- include/configs/qong.h | 6 +- include/configs/s5p_goni.h | 6 +- include/configs/s5pc210_universal.h | 6 +- include/configs/trats.h | 14 +- include/configs/tt01.h | 6 +- include/configs/vision2.h | 6 +- include/pmic.h | 72 ----- include/power/battery.h | 38 +++ include/power/fg_battery_cell_params.h | 90 ++++++ include/power/max17042_fg.h | 74 +++++ include/power/max8997_muic.h | 61 ++++ include/{ => power}/max8997_pmic.h | 26 ++- include/{ => power}/max8998_pmic.h | 0 include/power/pmic.h | 109 ++++++++ include/power/power_chrg.h | 43 +++ 56 files changed, 2027 insertions(+), 491 deletions(-) delete mode 100644 drivers/misc/pmic_core.c delete mode 100644 drivers/misc/pmic_i2c.c delete mode 100644 drivers/misc/pmic_max8997.c create mode 100644 drivers/power/battery/Makefile create mode 100644 drivers/power/battery/bat_trats.c create mode 100644 drivers/power/fuel_gauge/Makefile create mode 100644 drivers/power/fuel_gauge/fg_max17042.c create mode 100644 drivers/power/pmic/Makefile create mode 100644 drivers/power/pmic/muic_max8997.c create mode 100644 drivers/power/pmic/pmic_max8997.c rename drivers/{misc => power/pmic}/pmic_max8998.c (82%) create mode 100644 drivers/power/power_core.c rename drivers/{misc/pmic_dialog.c => power/power_dialog.c} (81%) rename drivers/{misc/pmic_fsl.c => power/power_fsl.c} (81%) create mode 100644 drivers/power/power_i2c.c rename drivers/{misc/pmic_spi.c => power/power_spi.c} (97%) delete mode 100644 include/pmic.h create mode 100644 include/power/battery.h create mode 100644 include/power/fg_battery_cell_params.h create mode 100644 include/power/max17042_fg.h create mode 100644 include/power/max8997_muic.h rename include/{ => power}/max8997_pmic.h (88%) rename include/{ => power}/max8998_pmic.h (100%) create mode 100644 include/power/pmic.h create mode 100644 include/power/power_chrg.h -- 1.7.2.3

4 30

[U-Boot] [PATCH 00/11] arm: add Faraday A36x SoC platform support
by Kuo-Jung Su 07 Apr '14

07 Apr '14

From: Kuo-Jung Su <dantesu(a)faraday-tech.com> These patches introduce Faraday A36x SoC platform support. Here are some public documents for your reference. http://www.faraday-tech.com/html/documentation/index.html There is also a A369 QEMU emulator available at my github account: https://github.com/dantesu1218/qemu.git Here is quick start for QEMU: 1. Download the QEMU source tree $ git clone -b qemu-1.3.0 https://github.com/dantesu1218/qemu.git 2. Build & Install the QEMU: $ ./configure --target-list=arm-softmmu $ make $ make install 3. Launch u-boot with QEMU: $ qemu-system-arm -M a369 -m 512M -nographic -kernel ~/u-boot-2012.10/u-boot Kuo-Jung Su (11): arm: add MMU/d-cache support for Faraday cores net/ftgmac100: add MMU/D-cache support net: add FTMAC110 10/100Mbps ethernet support usb-ehci: add Faraday USB 2.0 EHCI controller support usb-gadget: add FOTG210 USB gadget support i2c: add FTI2C010 I2C controller support spi: add FTSPI010 SPI controller support mtd/nand: add FTNANDC021 NAND flash controller support mtd/spi: add FTSPI020 SPI Flash controller support mmc: add an alternative FTSDC010 driver support arm: add Faraday A36x SoC platform support arch/arm/cpu/faraday/Makefile | 57 ++ arch/arm/cpu/faraday/a360/Makefile | 49 ++ arch/arm/cpu/faraday/a360/reset.c | 22 + arch/arm/cpu/faraday/a369/Makefile | 50 ++ arch/arm/cpu/faraday/a369/cmd_fa606.c | 74 +++ arch/arm/cpu/faraday/a369/reset.c | 22 + arch/arm/cpu/faraday/cmd_bootfa.c | 121 ++++ arch/arm/cpu/faraday/config.mk | 33 + arch/arm/cpu/faraday/cpu.c | 230 +++++++ arch/arm/cpu/faraday/ftpwmtmr010.c | 165 +++++ arch/arm/cpu/faraday/fttmr010.c | 155 +++++ arch/arm/cpu/faraday/fwimage.h | 38 ++ arch/arm/cpu/faraday/fwimage2.h | 70 +++ arch/arm/cpu/faraday/interrupts.c | 169 ++++++ arch/arm/cpu/faraday/start.S | 535 +++++++++++++++++ arch/arm/cpu/u-boot.lds | 11 + arch/arm/include/asm/arch-a360/hardware.h | 80 +++ arch/arm/include/asm/arch-a369/hardware.h | 106 ++++ arch/arm/include/asm/dma-mapping.h | 55 +- arch/arm/include/asm/global_data.h | 4 + arch/arm/include/asm/io.h | 75 +++ arch/arm/include/asm/mach-types.h | 1 + arch/arm/lib/cache-cp15.c | 44 ++ board/faraday/a360evb/Makefile | 49 ++ board/faraday/a360evb/board.c | 65 ++ board/faraday/a360evb/clk.c | 48 ++ board/faraday/a360evb/config.mk | 33 + board/faraday/a360evb/lowlevel_init.S | 33 + board/faraday/a369evb/Makefile | 49 ++ board/faraday/a369evb/board.c | 182 ++++++ board/faraday/a369evb/clk.c | 80 +++ board/faraday/a369evb/config.mk | 33 + board/faraday/a369evb/lowlevel_init.S | 133 +++++ boards.cfg | 3 + common/cmd_boot.c | 4 + common/usb_hub.c | 5 + drivers/i2c/Makefile | 1 + drivers/i2c/fti2c010.c | 360 +++++++++++ drivers/i2c/fti2c010.h | 68 +++ drivers/mmc/Makefile | 1 + drivers/mmc/ftsdc010_mci.c | 362 +++++++++++ drivers/mmc/ftsdc010_mci.h | 91 +++ drivers/mtd/nand/Makefile | 1 + drivers/mtd/nand/ftnandc021.c | 550 +++++++++++++++++ drivers/mtd/nand/ftnandc021.h | 165 +++++ drivers/mtd/spi/Makefile | 4 + drivers/mtd/spi/ftspi020.c | 589 ++++++++++++++++++ drivers/mtd/spi/ftspi020.h | 118 ++++ drivers/mtd/spi/winbond.c | 17 +- drivers/net/Makefile | 1 + drivers/net/ftgmac100.c | 83 ++- drivers/net/ftmac110.c | 484 +++++++++++++++ drivers/net/ftmac110.h | 131 ++++ drivers/spi/Makefile | 1 + drivers/spi/ftssp010_spi.c | 333 +++++++++++ drivers/spi/ftssp010_spi.h | 85 +++ drivers/usb/gadget/Makefile | 1 + drivers/usb/gadget/fotg210.c | 926 +++++++++++++++++++++++++++++ drivers/usb/gadget/fotg210.h | 99 +++ drivers/usb/gadget/gadget_chips.h | 8 + drivers/usb/host/Makefile | 1 + drivers/usb/host/ehci-faraday.c | 157 +++++ drivers/usb/host/ehci-hcd.c | 11 + drivers/usb/host/ehci.h | 5 + include/common.h | 13 + include/configs/a360.h | 180 ++++++ include/configs/a369.h | 40 ++ include/configs/a369_defaults.h | 285 +++++++++ include/configs/a369_fa606te.h | 32 + include/faraday/fttmr010.h | 51 +- include/faraday/ftwdt010_wdt.h | 8 + 71 files changed, 8110 insertions(+), 35 deletions(-) create mode 100644 arch/arm/cpu/faraday/Makefile create mode 100644 arch/arm/cpu/faraday/a360/Makefile create mode 100644 arch/arm/cpu/faraday/a360/reset.c create mode 100644 arch/arm/cpu/faraday/a369/Makefile create mode 100644 arch/arm/cpu/faraday/a369/cmd_fa606.c create mode 100644 arch/arm/cpu/faraday/a369/reset.c create mode 100644 arch/arm/cpu/faraday/cmd_bootfa.c create mode 100644 arch/arm/cpu/faraday/config.mk create mode 100644 arch/arm/cpu/faraday/cpu.c create mode 100644 arch/arm/cpu/faraday/ftpwmtmr010.c create mode 100644 arch/arm/cpu/faraday/fttmr010.c create mode 100644 arch/arm/cpu/faraday/fwimage.h create mode 100644 arch/arm/cpu/faraday/fwimage2.h create mode 100644 arch/arm/cpu/faraday/interrupts.c create mode 100644 arch/arm/cpu/faraday/start.S create mode 100644 arch/arm/include/asm/arch-a360/hardware.h create mode 100644 arch/arm/include/asm/arch-a369/hardware.h create mode 100644 board/faraday/a360evb/Makefile create mode 100644 board/faraday/a360evb/board.c create mode 100644 board/faraday/a360evb/clk.c create mode 100644 board/faraday/a360evb/config.mk create mode 100644 board/faraday/a360evb/lowlevel_init.S create mode 100644 board/faraday/a369evb/Makefile create mode 100644 board/faraday/a369evb/board.c create mode 100644 board/faraday/a369evb/clk.c create mode 100644 board/faraday/a369evb/config.mk create mode 100644 board/faraday/a369evb/lowlevel_init.S create mode 100644 drivers/i2c/fti2c010.c create mode 100644 drivers/i2c/fti2c010.h create mode 100644 drivers/mmc/ftsdc010_mci.c create mode 100644 drivers/mmc/ftsdc010_mci.h create mode 100644 drivers/mtd/nand/ftnandc021.c create mode 100644 drivers/mtd/nand/ftnandc021.h create mode 100644 drivers/mtd/spi/ftspi020.c create mode 100644 drivers/mtd/spi/ftspi020.h create mode 100644 drivers/net/ftmac110.c create mode 100644 drivers/net/ftmac110.h create mode 100644 drivers/spi/ftssp010_spi.c create mode 100644 drivers/spi/ftssp010_spi.h create mode 100644 drivers/usb/gadget/fotg210.c create mode 100644 drivers/usb/gadget/fotg210.h create mode 100644 drivers/usb/host/ehci-faraday.c create mode 100644 include/configs/a360.h create mode 100644 include/configs/a369.h create mode 100644 include/configs/a369_defaults.h create mode 100644 include/configs/a369_fa606te.h -- 1.7.9.5

12 310

[U-Boot] [PATCH 00/10] Add Marvell Dove and SolidRun CuBox
by Sebastian Hesselbarth 04 Mar '14

04 Mar '14

This patch set add support for the Marvell Dove 88AP510 SoC and the SolidRun CuBox board based on that SoC. The patch set is divided into the four following sections: (1) Patches 1-5: Add support for the Dove SoC and related drivers. Where possible drivers from Marvell Kirkwood are reused (mvsata, mvgbe), or forked to allow more generic usage (SPI, GPIO). The SDHCI driver is different and a new driver is added for it. The forked drivers can also be reused on Kirkwood but that would have required patching existing boards. (2) Patches 6-8: Allow mvgbe to use the phylib API, add support for 88E1310 PHY and allow Dove to use the driver. (3) Patch 9 Add the SolidRun CuBox as the first board based on Marvell Dove SoC. (4) Patch 10 Add support for different UART boot mode found on Dove. Sebastian Hesselbarth (10): ARM: dove: add support for Marvell Dove SoC GPIO: add gpio driver for Orion SoCs MMC: sdhci: Add support for dove sdhci SPI: Add Orion SPI driver block: mvsata: add dove include NET: phy: add 88E1310 PHY initialization NET: mvgbe: add phylib support NET: mvgbe: add support for Dove Boards: Add support for SolidRun CuBox tools: Add support for Dove to kwboot arch/arm/cpu/armv7/dove/Makefile | 49 +++++ arch/arm/cpu/armv7/dove/cpu.c | 266 ++++++++++++++++++++++++++ arch/arm/cpu/armv7/dove/dram.c | 116 +++++++++++ arch/arm/cpu/armv7/dove/lowlevel_init.S | 83 ++++++++ arch/arm/cpu/armv7/dove/mpp.c | 319 +++++++++++++++++++++++++++++++ arch/arm/cpu/armv7/dove/timer.c | 176 +++++++++++++++++ arch/arm/cpu/armv7/dove/usb.c | 101 ++++++++++ arch/arm/include/asm/arch-dove/config.h | 153 +++++++++++++++ arch/arm/include/asm/arch-dove/cpu.h | 204 ++++++++++++++++++++ arch/arm/include/asm/arch-dove/dove.h | 93 +++++++++ arch/arm/include/asm/arch-dove/gpio.h | 35 ++++ arch/arm/include/asm/arch-dove/mpp.h | 283 +++++++++++++++++++++++++++ board/solidrun/cubox/Makefile | 45 +++++ board/solidrun/cubox/cubox.c | 141 ++++++++++++++ board/solidrun/cubox/kwbimage.cfg | 76 ++++++++ boards.cfg | 1 + drivers/block/mvsata_ide.c | 2 + drivers/gpio/Makefile | 1 + drivers/gpio/orion_gpio.c | 167 ++++++++++++++++ drivers/mmc/Makefile | 1 + drivers/mmc/dove_sdhci.c | 101 ++++++++++ drivers/net/mvgbe.c | 70 ++++++- drivers/net/mvgbe.h | 7 + drivers/net/phy/marvell.c | 48 +++++ drivers/spi/Makefile | 1 + drivers/spi/orion_spi.c | 217 +++++++++++++++++++++ include/configs/cubox.h | 175 +++++++++++++++++ include/orion_gpio.h | 64 +++++++ tools/Makefile | 2 + tools/kwboot.c | 44 ++++- 30 files changed, 3033 insertions(+), 8 deletions(-) create mode 100644 arch/arm/cpu/armv7/dove/Makefile create mode 100644 arch/arm/cpu/armv7/dove/cpu.c create mode 100644 arch/arm/cpu/armv7/dove/dram.c create mode 100644 arch/arm/cpu/armv7/dove/lowlevel_init.S create mode 100644 arch/arm/cpu/armv7/dove/mpp.c create mode 100644 arch/arm/cpu/armv7/dove/timer.c create mode 100644 arch/arm/cpu/armv7/dove/usb.c create mode 100644 arch/arm/include/asm/arch-dove/config.h create mode 100644 arch/arm/include/asm/arch-dove/cpu.h create mode 100644 arch/arm/include/asm/arch-dove/dove.h create mode 100644 arch/arm/include/asm/arch-dove/gpio.h create mode 100644 arch/arm/include/asm/arch-dove/mpp.h create mode 100644 board/solidrun/cubox/Makefile create mode 100644 board/solidrun/cubox/cubox.c create mode 100644 board/solidrun/cubox/kwbimage.cfg create mode 100644 drivers/gpio/orion_gpio.c create mode 100644 drivers/mmc/dove_sdhci.c create mode 100644 drivers/spi/orion_spi.c create mode 100644 include/configs/cubox.h create mode 100644 include/orion_gpio.h --- Cc: u-boot(a)lists.denx.de Cc: Sebastian Hesselbarth <sebastian.hesselbarth(a)gmail.com> Cc: Rabeeh Khoury <rabeeh(a)solid-run.com> Cc: Albert Aribaud <albert.u.boot(a)aribaud.net> Cc: Prafulla Wadaskar <prafulla(a)marvell.com> Cc: Andy Fleming <afleming(a)gmail.com> Cc: Joe Hershberger <joe.hershberger(a)gmail.com> Cc: Daniel Stodden <daniel.stodden(a)gmail.com> Cc: Dieter Kiermaier <dk-arm-linux(a)gmx.de> -- 1.7.10.4

14 123

[U-Boot] [PATCH 2/2] ARM: OMAP4/5: Remove dead code against CONFIG_SYS_ENABLE_PADS_ALL
by Jassi Brar 24 Jan '14

24 Jan '14

The commit f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls" removed the config option aimed towards moving that stuff into kernel, which renders some code unreachable. Remove that code. Signed-off-by: Jassi Brar <jaswinder.singh(a)linaro.org> --- arch/arm/cpu/armv7/omap-common/hwinit-common.c | 6 - arch/arm/include/asm/arch-omap4/sys_proto.h | 1 - arch/arm/include/asm/arch-omap5/sys_proto.h | 1 - board/ti/omap5_evm/evm.c | 11 - board/ti/omap5_evm/mux_data.h | 234 ------------------------ board/ti/panda/panda.c | 28 --- board/ti/panda/panda_mux_data.h | 186 ------------------- board/ti/sdp4430/sdp.c | 18 -- board/ti/sdp4430/sdp4430_mux_data.h | 197 -------------------- 9 files changed, 0 insertions(+), 682 deletions(-) diff --git a/arch/arm/cpu/armv7/omap-common/hwinit-common.c b/arch/arm/cpu/armv7/omap-common/hwinit-common.c index 459ebb5..077fc27 100644 --- a/arch/arm/cpu/armv7/omap-common/hwinit-common.c +++ b/arch/arm/cpu/armv7/omap-common/hwinit-common.c @@ -51,16 +51,10 @@ static void set_mux_conf_regs(void) set_muxconf_regs_essential(); break; case OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL: -#ifdef CONFIG_SYS_ENABLE_PADS_ALL - set_muxconf_regs_non_essential(); -#endif break; case OMAP_INIT_CONTEXT_UBOOT_FROM_NOR: case OMAP_INIT_CONTEXT_UBOOT_AFTER_CH: set_muxconf_regs_essential(); -#ifdef CONFIG_SYS_ENABLE_PADS_ALL - set_muxconf_regs_non_essential(); -#endif break; } } diff --git a/arch/arm/include/asm/arch-omap4/sys_proto.h b/arch/arm/include/asm/arch-omap4/sys_proto.h index d633573..90befa1 100644 --- a/arch/arm/include/asm/arch-omap4/sys_proto.h +++ b/arch/arm/include/asm/arch-omap4/sys_proto.h @@ -37,7 +37,6 @@ void watchdog_init(void); u32 get_device_type(void); void do_set_mux(u32 base, struct pad_conf_entry const *array, int size); void set_muxconf_regs_essential(void); -void set_muxconf_regs_non_essential(void); void sr32(void *, u32, u32, u32); u32 wait_on_value(u32, u32, void *, u32); void sdelay(unsigned long); diff --git a/arch/arm/include/asm/arch-omap5/sys_proto.h b/arch/arm/include/asm/arch-omap5/sys_proto.h index 74feb90..9a49393 100644 --- a/arch/arm/include/asm/arch-omap5/sys_proto.h +++ b/arch/arm/include/asm/arch-omap5/sys_proto.h @@ -38,7 +38,6 @@ void watchdog_init(void); u32 get_device_type(void); void do_set_mux(u32 base, struct pad_conf_entry const *array, int size); void set_muxconf_regs_essential(void); -void set_muxconf_regs_non_essential(void); void sr32(void *, u32, u32, u32); u32 wait_on_value(u32, u32, void *, u32); void sdelay(unsigned long); diff --git a/board/ti/omap5_evm/evm.c b/board/ti/omap5_evm/evm.c index c8dfdf8..4b61819 100644 --- a/board/ti/omap5_evm/evm.c +++ b/board/ti/omap5_evm/evm.c @@ -80,17 +80,6 @@ void set_muxconf_regs_essential(void) sizeof(struct pad_conf_entry)); } -void set_muxconf_regs_non_essential(void) -{ - do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_non_essential, - sizeof(core_padconf_array_non_essential) / - sizeof(struct pad_conf_entry)); - - do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_non_essential, - sizeof(wkup_padconf_array_non_essential) / - sizeof(struct pad_conf_entry)); -} - #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC) int board_mmc_init(bd_t *bis) { diff --git a/board/ti/omap5_evm/mux_data.h b/board/ti/omap5_evm/mux_data.h index a82795d..c5af6cd 100644 --- a/board/ti/omap5_evm/mux_data.h +++ b/board/ti/omap5_evm/mux_data.h @@ -67,238 +67,4 @@ const struct pad_conf_entry wkup_padconf_array_essential[] = { }; -const struct pad_conf_entry core_padconf_array_non_essential[] = { - - {C2C_DATAIN0, (IEN | M0)}, /* C2C_DATAIN0 */ - {C2C_DATAIN1, (IEN | M0)}, /* C2C_DATAIN1 */ - {C2C_DATAIN2, (IEN | M0)}, /* C2C_DATAIN2 */ - {C2C_DATAIN3, (IEN | M0)}, /* C2C_DATAIN3 */ - {C2C_DATAIN4, (IEN | M0)}, /* C2C_DATAIN4 */ - {C2C_DATAIN5, (IEN | M0)}, /* C2C_DATAIN5 */ - {C2C_DATAIN6, (IEN | M0)}, /* C2C_DATAIN6 */ - {C2C_DATAIN7, (IEN | M0)}, /* C2C_DATAIN7 */ - {C2C_CLKIN1, (IEN | M0)}, /* C2C_CLKIN1 */ - {C2C_CLKIN0, (IEN | M0)}, /* C2C_CLKIN0 */ - {C2C_CLKOUT0, (M0)}, /* C2C_CLKOUT0 */ - {C2C_CLKOUT1, (M0)}, /* C2C_CLKOUT1 */ - {C2C_DATAOUT0, (M0)}, /* C2C_DATAOUT0 */ - {C2C_DATAOUT1, (M0)}, /* C2C_DATAOUT1 */ - {C2C_DATAOUT2, (M0)}, /* C2C_DATAOUT2 */ - {C2C_DATAOUT3, (M0)}, /* C2C_DATAOUT3 */ - {C2C_DATAOUT4, (M0)}, /* C2C_DATAOUT4 */ - {C2C_DATAOUT5, (M0)}, /* C2C_DATAOUT5 */ - {C2C_DATAOUT6, (M0)}, /* C2C_DATAOUT6 */ - {C2C_DATAOUT7, (M0)}, /* C2C_DATAOUT7 */ - {C2C_DATA8, (IEN | M0)}, /* C2C_DATA8 */ - {C2C_DATA9, (IEN | M0)}, /* C2C_DATA9 */ - {C2C_DATA10, (IEN | M0)}, /* C2C_DATA10 */ - {C2C_DATA11, (IEN | M0)}, /* C2C_DATA11 */ - {C2C_DATA12, (IEN | M0)}, /* C2C_DATA12 */ - {C2C_DATA13, (IEN | M0)}, /* C2C_DATA13 */ - {C2C_DATA14, (IEN | M0)}, /* C2C_DATA14 */ - {C2C_DATA15, (IEN | M0)}, /* C2C_DATA15 */ - {LLIB_WAKEREQOUT, (PTU | IEN | M6)}, /* GPIO2_32 */ - {LLIA_WAKEREQOUT, (M1)}, /* C2C_WAKEREQOUT */ - {HSI1_ACREADY, (PTD | M6)}, /* GPIO3_64 */ - {HSI1_CAREADY, (PTD | M6)}, /* GPIO3_65 */ - {HSI1_ACWAKE, (PTD | IEN | M6)}, /* GPIO3_66 */ - {HSI1_CAWAKE, (PTU | IEN | M6)}, /* GPIO3_67 */ - {HSI1_ACFLAG, (PTD | IEN | M6)}, /* GPIO3_68 */ - {HSI1_ACDATA, (PTD | M6)}, /* GPIO3_69 */ - {HSI1_CAFLAG, (M6)}, /* GPIO3_70 */ - {HSI1_CADATA, (M6)}, /* GPIO3_71 */ - {UART1_TX, (M0)}, /* UART1_TX */ - {UART1_CTS, (PTU | IEN | M0)}, /* UART1_CTS */ - {UART1_RX, (PTU | IEN | M0)}, /* UART1_RX */ - {UART1_RTS, (M0)}, /* UART1_RTS */ - {HSI2_CAREADY, (IEN | M0)}, /* HSI2_CAREADY */ - {HSI2_ACREADY, (OFF_EN | M0)}, /* HSI2_ACREADY */ - {HSI2_CAWAKE, (IEN | PTD | M0)}, /* HSI2_CAWAKE */ - {HSI2_ACWAKE, (M0)}, /* HSI2_ACWAKE */ - {HSI2_CAFLAG, (IEN | PTD | M0)}, /* HSI2_CAFLAG */ - {HSI2_CADATA, (IEN | PTD | M0)}, /* HSI2_CADATA */ - {HSI2_ACFLAG, (M0)}, /* HSI2_ACFLAG */ - {HSI2_ACDATA, (M0)}, /* HSI2_ACDATA */ - {UART2_RTS, (IEN | M1)}, /* MCSPI3_SOMI */ - {UART2_CTS, (IEN | M1)}, /* MCSPI3_CS0 */ - {UART2_RX, (IEN | M1)}, /* MCSPI3_SIMO */ - {UART2_TX, (IEN | M1)}, /* MCSPI3_CLK */ - {TIMER10_PWM_EVT, (IEN | M0)}, /* TIMER10_PWM_EVT */ - {DSIPORTA_TE0, (IEN | M0)}, /* DSIPORTA_TE0 */ - {DSIPORTA_LANE0X, (IEN | M0)}, /* DSIPORTA_LANE0X */ - {DSIPORTA_LANE0Y, (IEN | M0)}, /* DSIPORTA_LANE0Y */ - {DSIPORTA_LANE1X, (IEN | M0)}, /* DSIPORTA_LANE1X */ - {DSIPORTA_LANE1Y, (IEN | M0)}, /* DSIPORTA_LANE1Y */ - {DSIPORTA_LANE2X, (IEN | M0)}, /* DSIPORTA_LANE2X */ - {DSIPORTA_LANE2Y, (IEN | M0)}, /* DSIPORTA_LANE2Y */ - {DSIPORTA_LANE3X, (IEN | M0)}, /* DSIPORTA_LANE3X */ - {DSIPORTA_LANE3Y, (IEN | M0)}, /* DSIPORTA_LANE3Y */ - {DSIPORTA_LANE4X, (IEN | M0)}, /* DSIPORTA_LANE4X */ - {DSIPORTA_LANE4Y, (IEN | M0)}, /* DSIPORTA_LANE4Y */ - {TIMER9_PWM_EVT, (IEN | M0)}, /* TIMER9_PWM_EVT */ - {DSIPORTC_TE0, (IEN | M0)}, /* DSIPORTC_TE0 */ - {DSIPORTC_LANE0X, (IEN | M0)}, /* DSIPORTC_LANE0X */ - {DSIPORTC_LANE0Y, (IEN | M0)}, /* DSIPORTC_LANE0Y */ - {DSIPORTC_LANE1X, (IEN | M0)}, /* DSIPORTC_LANE1X */ - {DSIPORTC_LANE1Y, (IEN | M0)}, /* DSIPORTC_LANE1Y */ - {DSIPORTC_LANE2X, (IEN | M0)}, /* DSIPORTC_LANE2X */ - {DSIPORTC_LANE2Y, (IEN | M0)}, /* DSIPORTC_LANE2Y */ - {DSIPORTC_LANE3X, (IEN | M0)}, /* DSIPORTC_LANE3X */ - {DSIPORTC_LANE3Y, (IEN | M0)}, /* DSIPORTC_LANE3Y */ - {DSIPORTC_LANE4X, (IEN | M0)}, /* DSIPORTC_LANE4X */ - {DSIPORTC_LANE4Y, (IEN | M0)}, /* DSIPORTC_LANE4Y */ - {RFBI_HSYNC0, (M4)}, /* KBD_COL5 */ - {RFBI_TE_VSYNC0, (PTD | M6)}, /* GPIO6_161 */ - {RFBI_RE, (M4)}, /* KBD_COL4 */ - {RFBI_A0, (PTD | IEN | M6)}, /* GPIO6_165 */ - {RFBI_DATA8, (M4)}, /* KBD_COL3 */ - {RFBI_DATA9, (PTD | M6)}, /* GPIO6_175 */ - {RFBI_DATA10, (PTD | M6)}, /* GPIO6_176 */ - {RFBI_DATA11, (PTD | M6)}, /* GPIO6_177 */ - {RFBI_DATA12, (PTD | M6)}, /* GPIO6_178 */ - {RFBI_DATA13, (PTU | IEN | M6)}, /* GPIO6_179 */ - {RFBI_DATA14, (M4)}, /* KBD_COL7 */ - {RFBI_DATA15, (M4)}, /* KBD_COL6 */ - {GPIO6_182, (M6)}, /* GPIO6_182 */ - {GPIO6_183, (PTD | M6)}, /* GPIO6_183 */ - {GPIO6_184, (M4)}, /* KBD_COL2 */ - {GPIO6_185, (PTD | IEN | M6)}, /* GPIO6_185 */ - {GPIO6_186, (PTD | M6)}, /* GPIO6_186 */ - {GPIO6_187, (PTU | IEN | M4)}, /* KBD_ROW2 */ - {RFBI_DATA0, (PTD | M6)}, /* GPIO6_166 */ - {RFBI_DATA1, (PTD | M6)}, /* GPIO6_167 */ - {RFBI_DATA2, (PTD | M6)}, /* GPIO6_168 */ - {RFBI_DATA3, (PTD | IEN | M6)}, /* GPIO6_169 */ - {RFBI_DATA4, (IEN | M6)}, /* GPIO6_170 */ - {RFBI_DATA5, (IEN | M6)}, /* GPIO6_171 */ - {RFBI_DATA6, (PTD | M6)}, /* GPIO6_172 */ - {RFBI_DATA7, (PTD | M6)}, /* GPIO6_173 */ - {RFBI_CS0, (PTD | IEN | M6)}, /* GPIO6_163 */ - {RFBI_WE, (PTD | M6)}, /* GPIO6_162 */ - {MCSPI2_CS0, (M0)}, /* MCSPI2_CS0 */ - {MCSPI2_CLK, (IEN | M0)}, /* MCSPI2_CLK */ - {MCSPI2_SIMO, (IEN | M0)}, /* MCSPI2_SIMO*/ - {MCSPI2_SOMI, (PTU | IEN | M0)}, /* MCSPI2_SOMI*/ - {I2C4_SCL, (IEN | M0)}, /* I2C4_SCL */ - {I2C4_SDA, (IEN | M0)}, /* I2C4_SDA */ - {HDMI_CEC, (IEN | M0)}, /* HDMI_CEC */ - {HDMI_HPD, (PTD | IEN | M0)}, /* HDMI_HPD */ - {HDMI_DDC_SCL, (IEN | M0)}, /* HDMI_DDC_SCL */ - {HDMI_DDC_SDA, (IEN | M0)}, /* HDMI_DDC_SDA */ - {CSIPORTA_LANE0X, (IEN | M0)}, /* CSIPORTA_LANE0X */ - {CSIPORTA_LANE0Y, (IEN | M0)}, /* CSIPORTA_LANE0Y */ - {CSIPORTA_LANE1Y, (IEN | M0)}, /* CSIPORTA_LANE1Y */ - {CSIPORTA_LANE1X, (IEN | M0)}, /* CSIPORTA_LANE1X */ - {CSIPORTA_LANE2Y, (IEN | M0)}, /* CSIPORTA_LANE2Y */ - {CSIPORTA_LANE2X, (IEN | M0)}, /* CSIPORTA_LANE2X */ - {CSIPORTA_LANE3X, (IEN | M0)}, /* CSIPORTA_LANE3X */ - {CSIPORTA_LANE3Y, (IEN | M0)}, /* CSIPORTA_LANE3Y */ - {CSIPORTA_LANE4X, (IEN | M0)}, /* CSIPORTA_LANE4X */ - {CSIPORTA_LANE4Y, (IEN | M0)}, /* CSIPORTA_LANE4Y */ - {CSIPORTB_LANE0X, (IEN | M0)}, /* CSIPORTB_LANE0X */ - {CSIPORTB_LANE0Y, (IEN | M0)}, /* CSIPORTB_LANE0Y */ - {CSIPORTB_LANE1Y, (IEN | M0)}, /* CSIPORTB_LANE1Y */ - {CSIPORTB_LANE1X, (IEN | M0)}, /* CSIPORTB_LANE1X */ - {CSIPORTB_LANE2Y, (IEN | M0)}, /* CSIPORTB_LANE2Y */ - {CSIPORTB_LANE2X, (IEN | M0)}, /* CSIPORTB_LANE2X */ - {CSIPORTC_LANE0Y, (IEN | M0)}, /* CSIPORTC_LANE0Y */ - {CSIPORTC_LANE0X, (IEN | M0)}, /* CSIPORTC_LANE0X */ - {CSIPORTC_LANE1Y, (IEN | M0)}, /* CSIPORTC_LANE1Y */ - {CSIPORTC_LANE1X, (IEN | M0)}, /* CSIPORTC_LANE1X */ - {CAM_SHUTTER, (M0)}, /* CAM_SHUTTER */ - {CAM_STROBE, (M0)}, /* CAM_STROBE */ - {CAM_GLOBALRESET, (IEN | M0)}, /* CAM_GLOBALRESET */ - {TIMER11_PWM_EVT, (PTD | M6)}, /* GPIO8_227 */ - {TIMER5_PWM_EVT, (PTD | M6)}, /* GPIO8_228 */ - {TIMER6_PWM_EVT, (PTD | M6)}, /* GPIO8_229 */ - {TIMER8_PWM_EVT, (PTU | M6)}, /* GPIO8_230 */ - {I2C3_SCL, (IEN | M0)}, /* I2C3_SCL */ - {I2C3_SDA, (IEN | M0)}, /* I2C3_SDA */ - {GPIO8_233, (IEN | M2)}, /* TIMER8_PWM_EVT */ - {ABE_CLKS, (IEN | M0)}, /* ABE_CLKS */ - {ABEDMIC_DIN1, (IEN | M0)}, /* ABEDMIC_DIN1 */ - {ABEDMIC_DIN2, (IEN | M0)}, /* ABEDMIC_DIN2 */ - {ABEDMIC_DIN3, (IEN | M0)}, /* ABEDMIC_DIN3 */ - {ABEDMIC_CLK1, (M0)}, /* ABEDMIC_CLK1 */ - {ABEDMIC_CLK2, (IEN | M1)}, /* ABEMCBSP1_FSX */ - {ABEDMIC_CLK3, (M1)}, /* ABEMCBSP1_DX */ - {ABESLIMBUS1_CLOCK, (IEN | M1)}, /* ABEMCBSP1_CLKX */ - {ABESLIMBUS1_DATA, (IEN | M1)}, /* ABEMCBSP1_DR */ - {ABEMCBSP2_DR, (IEN | M0)}, /* ABEMCBSP2_DR */ - {ABEMCBSP2_DX, (M0)}, /* ABEMCBSP2_DX */ - {ABEMCBSP2_FSX, (IEN | M0)}, /* ABEMCBSP2_FSX */ - {ABEMCBSP2_CLKX, (IEN | M0)}, /* ABEMCBSP2_CLKX */ - {ABEMCPDM_UL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* ABEMCPDM_UL_DATA */ - {ABEMCPDM_DL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* ABEMCPDM_DL_DATA */ - {ABEMCPDM_FRAME, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* ABEMCPDM_FRAME */ - {ABEMCPDM_LB_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* ABEMCPDM_LB_CLK */ - {WLSDIO_CLK, (PTU | IEN | M0)}, /* WLSDIO_CLK */ - {WLSDIO_CMD, (PTU | IEN | M0)}, /* WLSDIO_CMD */ - {WLSDIO_DATA0, (PTU | IEN | M0)}, /* WLSDIO_DATA0*/ - {WLSDIO_DATA1, (PTU | IEN | M0)}, /* WLSDIO_DATA1*/ - {WLSDIO_DATA2, (PTU | IEN | M0)}, /* WLSDIO_DATA2*/ - {WLSDIO_DATA3, (PTU | IEN | M0)}, /* WLSDIO_DATA3*/ - {UART5_RX, (PTU | IEN | M0)}, /* UART5_RX */ - {UART5_TX, (M0)}, /* UART5_TX */ - {UART5_CTS, (PTU | IEN | M0)}, /* UART5_CTS */ - {UART5_RTS, (M0)}, /* UART5_RTS */ - {I2C2_SCL, (IEN | M0)}, /* I2C2_SCL */ - {I2C2_SDA, (IEN | M0)}, /* I2C2_SDA */ - {MCSPI1_CLK, (M6)}, /* GPIO5_140 */ - {MCSPI1_SOMI, (IEN | M6)}, /* GPIO5_141 */ - {MCSPI1_SIMO, (PTD | M6)}, /* GPIO5_142 */ - {MCSPI1_CS0, (PTD | M6)}, /* GPIO5_143 */ - {MCSPI1_CS1, (PTD | IEN | M6)}, /* GPIO5_144 */ - {I2C5_SCL, (IEN | M0)}, /* I2C5_SCL */ - {I2C5_SDA, (IEN | M0)}, /* I2C5_SDA */ - {PERSLIMBUS2_CLOCK, (PTD | M6)}, /* GPIO5_145 */ - {PERSLIMBUS2_DATA, (PTD | IEN | M6)}, /* GPIO5_146 */ - {UART6_TX, (PTU | IEN | M6)}, /* GPIO5_149 */ - {UART6_RX, (PTU | IEN | M6)}, /* GPIO5_150 */ - {UART6_CTS, (PTU | IEN | M6)}, /* GPIO5_151 */ - {UART6_RTS, (PTU | M0)}, /* UART6_RTS */ - {UART3_CTS_RCTX, (PTU | IEN | M6)}, /* GPIO5_153 */ - {UART3_RTS_IRSD, (PTU | IEN | M1)}, /* HDQ_SIO */ - {I2C1_PMIC_SCL, (PTU | IEN | M0)}, /* I2C1_PMIC_SCL */ - {I2C1_PMIC_SDA, (PTU | IEN | M0)}, /* I2C1_PMIC_SDA */ - -}; - -const struct pad_conf_entry wkup_padconf_array_non_essential[] = { - -/* - * This pad keeps C2C Module always enabled. - * Putting this in safe mode do not cause the issue. - * C2C driver could enable this mux setting if needed. - */ - {LLIA_WAKEREQIN, (M7)}, /* SAFE MODE */ - {LLIB_WAKEREQIN, (M7)}, /* SAFE MODE */ - {DRM_EMU0, (PTU | IEN | M0)}, /* DRM_EMU0 */ - {DRM_EMU1, (PTU | IEN | M0)}, /* DRM_EMU1 */ - {JTAG_NTRST, (IEN | M0)}, /* JTAG_NTRST */ - {JTAG_TCK, (IEN | M0)}, /* JTAG_TCK */ - {JTAG_RTCK, (M0)}, /* JTAG_RTCK */ - {JTAG_TMSC, (IEN | M0)}, /* JTAG_TMSC */ - {JTAG_TDI, (IEN | M0)}, /* JTAG_TDI */ - {JTAG_TDO, (M0)}, /* JTAG_TDO */ - {FREF_CLK_IOREQ, (IEN | M0)}, /* FREF_CLK_IOREQ */ - {FREF_CLK0_OUT, (M0)}, /* FREF_CLK0_OUT */ - {FREF_CLK1_OUT, (M0)}, /* FREF_CLK1_OUT */ - {FREF_CLK2_OUT, (M0)}, /* FREF_CLK2_OUT */ - {FREF_CLK2_REQ, (PTU | IEN | M6)}, /* GPIO1_WK9 */ - {FREF_CLK1_REQ, (PTD | IEN | M6)}, /* GPIO1_WK8 */ - {SYS_NRESPWRON, (IEN | M0)}, /* SYS_NRESPWRON */ - {SYS_NRESWARM, (PTU | IEN | M0)}, /* SYS_NRESWARM */ - {SYS_PWR_REQ, (M0)}, /* SYS_PWR_REQ */ - {SYS_NIRQ1, (PTU | IEN | M0)}, /* SYS_NIRQ1 */ - {SYS_NIRQ2, (PTU | IEN | M0)}, /* SYS_NIRQ2 */ - {SYS_BOOT0, (IEN | M0)}, /* SYS_BOOT0 */ - {SYS_BOOT1, (IEN | M0)}, /* SYS_BOOT1 */ - {SYS_BOOT2, (IEN | M0)}, /* SYS_BOOT2 */ - {SYS_BOOT3, (IEN | M0)}, /* SYS_BOOT3 */ - {SYS_BOOT4, (IEN | M0)}, /* SYS_BOOT4 */ - {SYS_BOOT5, (IEN | M0)}, /* SYS_BOOT5 */ - -}; - #endif /* _EVM4430_MUX_DATA_H */ diff --git a/board/ti/panda/panda.c b/board/ti/panda/panda.c index ee82771..25cbc7c 100644 --- a/board/ti/panda/panda.c +++ b/board/ti/panda/panda.c @@ -148,34 +148,6 @@ void set_muxconf_regs_essential(void) sizeof(struct pad_conf_entry)); } -void set_muxconf_regs_non_essential(void) -{ - do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_non_essential, - sizeof(core_padconf_array_non_essential) / - sizeof(struct pad_conf_entry)); - - if (omap_revision() < OMAP4460_ES1_0) - do_set_mux(CONTROL_PADCONF_CORE, - core_padconf_array_non_essential_4430, - sizeof(core_padconf_array_non_essential_4430) / - sizeof(struct pad_conf_entry)); - else - do_set_mux(CONTROL_PADCONF_CORE, - core_padconf_array_non_essential_4460, - sizeof(core_padconf_array_non_essential_4460) / - sizeof(struct pad_conf_entry)); - - do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_non_essential, - sizeof(wkup_padconf_array_non_essential) / - sizeof(struct pad_conf_entry)); - - if (omap_revision() < OMAP4460_ES1_0) - do_set_mux(CONTROL_PADCONF_WKUP, - wkup_padconf_array_non_essential_4430, - sizeof(wkup_padconf_array_non_essential_4430) / - sizeof(struct pad_conf_entry)); -} - #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC) int board_mmc_init(bd_t *bis) { diff --git a/board/ti/panda/panda_mux_data.h b/board/ti/panda/panda_mux_data.h index 5939257..4300401 100644 --- a/board/ti/panda/panda_mux_data.h +++ b/board/ti/panda/panda_mux_data.h @@ -100,190 +100,4 @@ const struct pad_conf_entry wkup_padconf_array_essential_4460[] = { }; -const struct pad_conf_entry core_padconf_array_non_essential[] = { - {GPMC_AD8, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* gpio_32 */ - {GPMC_AD9, (PTU | IEN | M3)}, /* gpio_33 */ - {GPMC_AD10, (PTU | IEN | M3)}, /* gpio_34 */ - {GPMC_AD11, (PTU | IEN | M3)}, /* gpio_35 */ - {GPMC_AD12, (PTU | IEN | M3)}, /* gpio_36 */ - {GPMC_AD13, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_37 */ - {GPMC_AD14, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_38 */ - {GPMC_AD15, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_39 */ - {GPMC_A16, (M3)}, /* gpio_40 */ - {GPMC_A17, (PTD | M3)}, /* gpio_41 */ - {GPMC_A18, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row6 */ - {GPMC_A19, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row7 */ - {GPMC_A20, (IEN | M3)}, /* gpio_44 */ - {GPMC_A21, (M3)}, /* gpio_45 */ - {GPMC_A22, (M3)}, /* gpio_46 */ - {GPMC_A23, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col7 */ - {GPMC_A24, (PTD | M3)}, /* gpio_48 */ - {GPMC_A25, (PTD | M3)}, /* gpio_49 */ - {GPMC_NCS0, (M3)}, /* gpio_50 */ - {GPMC_NCS1, (IEN | M3)}, /* gpio_51 */ - {GPMC_NCS2, (IEN | M3)}, /* gpio_52 */ - {GPMC_NCS3, (IEN | M3)}, /* gpio_53 */ - {GPMC_NWP, (M3)}, /* gpio_54 */ - {GPMC_CLK, (PTD | M3)}, /* gpio_55 */ - {GPMC_NADV_ALE, (M3)}, /* gpio_56 */ - {GPMC_NBE0_CLE, (M3)}, /* gpio_59 */ - {GPMC_NBE1, (PTD | M3)}, /* gpio_60 */ - {GPMC_WAIT0, (PTU | IEN | M3)}, /* gpio_61 */ - {C2C_DATA11, (PTD | M3)}, /* gpio_100 */ - {C2C_DATA12, (PTU | IEN | M3)}, /* gpio_101 */ - {C2C_DATA13, (PTD | M3)}, /* gpio_102 */ - {C2C_DATA14, (M1)}, /* dsi2_te0 */ - {C2C_DATA15, (PTD | M3)}, /* gpio_104 */ - {HDMI_HPD, (M0)}, /* hdmi_hpd */ - {HDMI_CEC, (M0)}, /* hdmi_cec */ - {HDMI_DDC_SCL, (PTU | M0)}, /* hdmi_ddc_scl */ - {HDMI_DDC_SDA, (PTU | IEN | M0)}, /* hdmi_ddc_sda */ - {CSI21_DX0, (IEN | M0)}, /* csi21_dx0 */ - {CSI21_DY0, (IEN | M0)}, /* csi21_dy0 */ - {CSI21_DX1, (IEN | M0)}, /* csi21_dx1 */ - {CSI21_DY1, (IEN | M0)}, /* csi21_dy1 */ - {CSI21_DX2, (IEN | M0)}, /* csi21_dx2 */ - {CSI21_DY2, (IEN | M0)}, /* csi21_dy2 */ - {CSI21_DX3, (PTD | M7)}, /* csi21_dx3 */ - {CSI21_DY3, (PTD | M7)}, /* csi21_dy3 */ - {CSI21_DX4, (PTD | OFF_EN | OFF_PD | OFF_IN | M7)}, /* csi21_dx4 */ - {CSI21_DY4, (PTD | OFF_EN | OFF_PD | OFF_IN | M7)}, /* csi21_dy4 */ - {CSI22_DX0, (IEN | M0)}, /* csi22_dx0 */ - {CSI22_DY0, (IEN | M0)}, /* csi22_dy0 */ - {CSI22_DX1, (IEN | M0)}, /* csi22_dx1 */ - {CSI22_DY1, (IEN | M0)}, /* csi22_dy1 */ - {CAM_SHUTTER, (OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* cam_shutter */ - {CAM_STROBE, (OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* cam_strobe */ - {CAM_GLOBALRESET, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_83 */ - {ABE_MCBSP2_DR, (IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dr */ - {ABE_MCBSP2_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dx */ - {ABE_MCBSP2_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_fsx */ - {ABE_MCBSP1_CLKX, (IEN | M0)}, /* abe_mcbsp1_clkx */ - {ABE_MCBSP1_DR, (IEN | M0)}, /* abe_mcbsp1_dr */ - {ABE_MCBSP1_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp1_dx */ - {ABE_MCBSP1_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp1_fsx */ - {ABE_PDM_UL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_ul_data */ - {ABE_PDM_DL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_dl_data */ - {ABE_PDM_FRAME, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_frame */ - {ABE_PDM_LB_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_lb_clk */ - {ABE_CLKS, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_clks */ - {ABE_DMIC_CLK1, (M0)}, /* abe_dmic_clk1 */ - {ABE_DMIC_DIN1, (IEN | M0)}, /* abe_dmic_din1 */ - {ABE_DMIC_DIN2, (PTU | IEN | M3)}, /* gpio_121 */ - {ABE_DMIC_DIN3, (IEN | M0)}, /* abe_dmic_din3 */ - {UART2_CTS, (PTU | IEN | M7)}, /* uart2_cts */ - {UART2_RTS, (M7)}, /* uart2_rts */ - {UART2_RX, (PTU | IEN | M7)}, /* uart2_rx */ - {UART2_TX, (M7)}, /* uart2_tx */ - {HDQ_SIO, (M3)}, /* gpio_127 */ - {MCSPI1_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_clk */ - {MCSPI1_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_somi */ - {MCSPI1_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_simo */ - {MCSPI1_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_cs0 */ - {MCSPI1_CS1, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* mcspi1_cs1 */ - {MCSPI1_CS2, (PTU | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_139 */ - {MCSPI1_CS3, (PTU | IEN | M3)}, /* gpio_140 */ - {SDMMC5_CLK, (PTU | IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* sdmmc5_clk */ - {SDMMC5_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_cmd */ - {SDMMC5_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat0 */ - {SDMMC5_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat1 */ - {SDMMC5_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat2 */ - {SDMMC5_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat3 */ - {MCSPI4_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_clk */ - {MCSPI4_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_simo */ - {MCSPI4_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_somi */ - {MCSPI4_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_cs0 */ - {UART4_RX, (IEN | M0)}, /* uart4_rx */ - {UART4_TX, (M0)}, /* uart4_tx */ - {USBB2_ULPITLL_CLK, (IEN | M3)}, /* gpio_157 */ - {USBB2_ULPITLL_STP, (IEN | M5)}, /* dispc2_data23 */ - {USBB2_ULPITLL_DIR, (IEN | M5)}, /* dispc2_data22 */ - {USBB2_ULPITLL_NXT, (IEN | M5)}, /* dispc2_data21 */ - {USBB2_ULPITLL_DAT0, (IEN | M5)}, /* dispc2_data20 */ - {USBB2_ULPITLL_DAT1, (IEN | M5)}, /* dispc2_data19 */ - {USBB2_ULPITLL_DAT2, (IEN | M5)}, /* dispc2_data18 */ - {USBB2_ULPITLL_DAT3, (IEN | M5)}, /* dispc2_data15 */ - {USBB2_ULPITLL_DAT4, (IEN | M5)}, /* dispc2_data14 */ - {USBB2_ULPITLL_DAT5, (IEN | M5)}, /* dispc2_data13 */ - {USBB2_ULPITLL_DAT6, (IEN | M5)}, /* dispc2_data12 */ - {USBB2_ULPITLL_DAT7, (IEN | M5)}, /* dispc2_data11 */ - {USBB2_HSIC_DATA, (PTD | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_169 */ - {USBB2_HSIC_STROBE, (PTD | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_170 */ - {UNIPRO_TX0, (PTD | IEN | M3)}, /* gpio_171 */ - {UNIPRO_TY0, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col1 */ - {UNIPRO_TX1, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col2 */ - {UNIPRO_TY1, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col3 */ - {UNIPRO_TX2, (PTU | IEN | M3)}, /* gpio_0 */ - {UNIPRO_RX0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row0 */ - {UNIPRO_RY0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row1 */ - {UNIPRO_RX1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row2 */ - {UNIPRO_RY1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row3 */ - {UNIPRO_RX2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row4 */ - {UNIPRO_RY2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row5 */ - {USBA0_OTG_CE, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* usba0_otg_ce */ - {USBA0_OTG_DP, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dp */ - {USBA0_OTG_DM, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dm */ - {FREF_CLK1_OUT, (M0)}, /* fref_clk1_out */ - {SYS_NIRQ1, (PTU | IEN | M0)}, /* sys_nirq1 */ - {SYS_NIRQ2, (PTU | IEN | M0)}, /* sys_nirq2 */ - {SYS_BOOT0, (PTU | IEN | M3)}, /* gpio_184 */ - {SYS_BOOT1, (M3)}, /* gpio_185 */ - {SYS_BOOT2, (PTD | IEN | M3)}, /* gpio_186 */ - {SYS_BOOT3, (M3)}, /* gpio_187 */ - {SYS_BOOT4, (M3)}, /* gpio_188 */ - {SYS_BOOT5, (PTD | IEN | M3)}, /* gpio_189 */ - {DPM_EMU0, (IEN | M0)}, /* dpm_emu0 */ - {DPM_EMU1, (IEN | M0)}, /* dpm_emu1 */ - {DPM_EMU2, (IEN | M0)}, /* dpm_emu2 */ - {DPM_EMU3, (IEN | M5)}, /* dispc2_data10 */ - {DPM_EMU4, (IEN | M5)}, /* dispc2_data9 */ - {DPM_EMU5, (IEN | M5)}, /* dispc2_data16 */ - {DPM_EMU6, (IEN | M5)}, /* dispc2_data17 */ - {DPM_EMU7, (IEN | M5)}, /* dispc2_hsync */ - {DPM_EMU8, (IEN | M5)}, /* dispc2_pclk */ - {DPM_EMU9, (IEN | M5)}, /* dispc2_vsync */ - {DPM_EMU10, (IEN | M5)}, /* dispc2_de */ - {DPM_EMU11, (IEN | M5)}, /* dispc2_data8 */ - {DPM_EMU12, (IEN | M5)}, /* dispc2_data7 */ - {DPM_EMU13, (IEN | M5)}, /* dispc2_data6 */ - {DPM_EMU14, (IEN | M5)}, /* dispc2_data5 */ - {DPM_EMU15, (IEN | M5)}, /* dispc2_data4 */ - {DPM_EMU16, (M3)}, /* gpio_27 */ - {DPM_EMU17, (IEN | M5)}, /* dispc2_data2 */ - {DPM_EMU18, (IEN | M5)}, /* dispc2_data1 */ - {DPM_EMU19, (IEN | M5)}, /* dispc2_data0 */ -}; - -const struct pad_conf_entry core_padconf_array_non_essential_4430[] = { - {ABE_MCBSP2_CLKX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_clkx */ -}; - -const struct pad_conf_entry core_padconf_array_non_essential_4460[] = { - {ABE_MCBSP2_CLKX, (PTU | OFF_EN | OFF_OUT_PTU | M3)}, /* led status_1 */ -}; - -const struct pad_conf_entry wkup_padconf_array_non_essential[] = { - {PAD0_SIM_IO, (IEN | M0)}, /* sim_io */ - {PAD1_SIM_CLK, (M0)}, /* sim_clk */ - {PAD0_SIM_RESET, (M0)}, /* sim_reset */ - {PAD1_SIM_CD, (PTU | IEN | M0)}, /* sim_cd */ - {PAD0_SIM_PWRCTRL, (M0)}, /* sim_pwrctrl */ - {PAD1_FREF_XTAL_IN, (M0)}, /* # */ - {PAD0_FREF_SLICER_IN, (M0)}, /* fref_slicer_in */ - {PAD1_FREF_CLK_IOREQ, (M0)}, /* fref_clk_ioreq */ - {PAD0_FREF_CLK0_OUT, (M2)}, /* sys_drm_msecure */ - {PAD1_FREF_CLK3_REQ, M7}, /* safe mode */ - {PAD0_FREF_CLK4_OUT, (PTU | M3)}, /* led status_2 */ - {PAD0_SYS_NRESPWRON, (M0)}, /* sys_nrespwron */ - {PAD1_SYS_NRESWARM, (M0)}, /* sys_nreswarm */ - {PAD0_SYS_PWR_REQ, (PTU | M0)}, /* sys_pwr_req */ - {PAD1_SYS_PWRON_RESET, (M3)}, /* gpio_wk29 */ - {PAD0_SYS_BOOT6, (IEN | M3)}, /* gpio_wk9 */ - {PAD1_SYS_BOOT7, (IEN | M3)}, /* gpio_wk10 */ -}; - -const struct pad_conf_entry wkup_padconf_array_non_essential_4430[] = { - {PAD1_FREF_CLK4_REQ, (PTU | M3)}, /* led status_1 */ -}; - #endif /* _PANDA_MUX_DATA_H_ */ diff --git a/board/ti/sdp4430/sdp.c b/board/ti/sdp4430/sdp.c index 982c771..4d31dac 100644 --- a/board/ti/sdp4430/sdp.c +++ b/board/ti/sdp4430/sdp.c @@ -87,24 +87,6 @@ void set_muxconf_regs_essential(void) sizeof(struct pad_conf_entry)); } -void set_muxconf_regs_non_essential(void) -{ - do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_non_essential, - sizeof(core_padconf_array_non_essential) / - sizeof(struct pad_conf_entry)); - - do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_non_essential, - sizeof(wkup_padconf_array_non_essential) / - sizeof(struct pad_conf_entry)); - - if (omap_revision() < OMAP4460_ES1_0) { - do_set_mux(CONTROL_PADCONF_WKUP, - wkup_padconf_array_non_essential_4430, - sizeof(wkup_padconf_array_non_essential_4430) / - sizeof(struct pad_conf_entry)); - } -} - #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC) int board_mmc_init(bd_t *bis) { diff --git a/board/ti/sdp4430/sdp4430_mux_data.h b/board/ti/sdp4430/sdp4430_mux_data.h index 0760dad..76a9331 100644 --- a/board/ti/sdp4430/sdp4430_mux_data.h +++ b/board/ti/sdp4430/sdp4430_mux_data.h @@ -81,201 +81,4 @@ const struct pad_conf_entry wkup_padconf_array_essential_4460[] = { }; -const struct pad_conf_entry core_padconf_array_non_essential[] = { - {GPMC_AD8, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* gpio_32 */ - {GPMC_AD9, (PTU | IEN | M3)}, /* gpio_33 */ - {GPMC_AD10, (PTU | IEN | M3)}, /* gpio_34 */ - {GPMC_AD11, (PTU | IEN | M3)}, /* gpio_35 */ - {GPMC_AD12, (PTU | IEN | M3)}, /* gpio_36 */ - {GPMC_AD13, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_37 */ - {GPMC_AD14, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_38 */ - {GPMC_AD15, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_39 */ - {GPMC_A16, (M3)}, /* gpio_40 */ - {GPMC_A17, (PTD | M3)}, /* gpio_41 */ - {GPMC_A18, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row6 */ - {GPMC_A19, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row7 */ - {GPMC_A20, (IEN | M3)}, /* gpio_44 */ - {GPMC_A21, (M3)}, /* gpio_45 */ - {GPMC_A22, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col6 */ - {GPMC_A23, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col7 */ - {GPMC_A24, (PTD | M3)}, /* gpio_48 */ - {GPMC_A25, (PTD | M3)}, /* gpio_49 */ - {GPMC_NCS0, (M3)}, /* gpio_50 */ - {GPMC_NCS1, (IEN | M3)}, /* gpio_51 */ - {GPMC_NCS2, (IEN | M3)}, /* gpio_52 */ - {GPMC_NCS3, (IEN | M3)}, /* gpio_53 */ - {GPMC_NWP, (M3)}, /* gpio_54 */ - {GPMC_CLK, (PTD | M3)}, /* gpio_55 */ - {GPMC_NADV_ALE, (M3)}, /* gpio_56 */ - {GPMC_NBE0_CLE, (M3)}, /* gpio_59 */ - {GPMC_NBE1, (PTD | M3)}, /* gpio_60 */ - {GPMC_WAIT0, (PTU | IEN | M3)}, /* gpio_61 */ - {GPMC_WAIT1, (IEN | M3)}, /* gpio_62 */ - {C2C_DATA11, (PTD | M3)}, /* gpio_100 */ - {C2C_DATA12, (M1)}, /* dsi1_te0 */ - {C2C_DATA13, (PTD | M3)}, /* gpio_102 */ - {C2C_DATA14, (M1)}, /* dsi2_te0 */ - {C2C_DATA15, (PTD | M3)}, /* gpio_104 */ - {HDMI_HPD, (M0)}, /* hdmi_hpd */ - {HDMI_CEC, (M0)}, /* hdmi_cec */ - {HDMI_DDC_SCL, (PTU | M0)}, /* hdmi_ddc_scl */ - {HDMI_DDC_SDA, (PTU | IEN | M0)}, /* hdmi_ddc_sda */ - {CSI21_DX0, (IEN | M0)}, /* csi21_dx0 */ - {CSI21_DY0, (IEN | M0)}, /* csi21_dy0 */ - {CSI21_DX1, (IEN | M0)}, /* csi21_dx1 */ - {CSI21_DY1, (IEN | M0)}, /* csi21_dy1 */ - {CSI21_DX2, (IEN | M0)}, /* csi21_dx2 */ - {CSI21_DY2, (IEN | M0)}, /* csi21_dy2 */ - {CSI21_DX3, (PTD | M7)}, /* csi21_dx3 */ - {CSI21_DY3, (PTD | M7)}, /* csi21_dy3 */ - {CSI21_DX4, (PTD | OFF_EN | OFF_PD | OFF_IN | M7)}, /* csi21_dx4 */ - {CSI21_DY4, (PTD | OFF_EN | OFF_PD | OFF_IN | M7)}, /* csi21_dy4 */ - {CSI22_DX0, (IEN | M0)}, /* csi22_dx0 */ - {CSI22_DY0, (IEN | M0)}, /* csi22_dy0 */ - {CSI22_DX1, (IEN | M0)}, /* csi22_dx1 */ - {CSI22_DY1, (IEN | M0)}, /* csi22_dy1 */ - {CAM_SHUTTER, (OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* cam_shutter */ - {CAM_STROBE, (OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* cam_strobe */ - {CAM_GLOBALRESET, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_83 */ - {USBB1_ULPITLL_CLK, (IEN | OFF_EN | OFF_IN | M1)}, /* hsi1_cawake */ - {USBB1_ULPITLL_STP, (IEN | OFF_EN | OFF_IN | M1)}, /* hsi1_cadata */ - {USBB1_ULPITLL_DIR, (IEN | OFF_EN | OFF_IN | M1)}, /* hsi1_caflag */ - {USBB1_ULPITLL_NXT, (OFF_EN | M1)}, /* hsi1_acready */ - {USBB1_ULPITLL_DAT0, (OFF_EN | M1)}, /* hsi1_acwake */ - {USBB1_ULPITLL_DAT1, (OFF_EN | M1)}, /* hsi1_acdata */ - {USBB1_ULPITLL_DAT2, (OFF_EN | M1)}, /* hsi1_acflag */ - {USBB1_ULPITLL_DAT3, (IEN | OFF_EN | OFF_IN | M1)}, /* hsi1_caready */ - {ABE_MCBSP2_CLKX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_clkx */ - {ABE_MCBSP2_DR, (IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dr */ - {ABE_MCBSP2_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dx */ - {ABE_MCBSP2_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_fsx */ - {ABE_MCBSP1_CLKX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp1_clkx */ - {ABE_MCBSP1_DR, (IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp1_dr */ - {ABE_MCBSP1_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp1_dx */ - {ABE_MCBSP1_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp1_fsx */ - {ABE_PDM_UL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_ul_data */ - {ABE_PDM_DL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_dl_data */ - {ABE_PDM_FRAME, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_frame */ - {ABE_PDM_LB_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_lb_clk */ - {ABE_CLKS, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_clks */ - {ABE_DMIC_CLK1, (M0)}, /* abe_dmic_clk1 */ - {ABE_DMIC_DIN1, (IEN | M0)}, /* abe_dmic_din1 */ - {ABE_DMIC_DIN2, (IEN | M0)}, /* abe_dmic_din2 */ - {ABE_DMIC_DIN3, (IEN | M0)}, /* abe_dmic_din3 */ - {UART2_CTS, (PTU | IEN | M0)}, /* uart2_cts */ - {UART2_RTS, (M0)}, /* uart2_rts */ - {UART2_RX, (PTU | IEN | M0)}, /* uart2_rx */ - {UART2_TX, (M0)}, /* uart2_tx */ - {HDQ_SIO, (M3)}, /* gpio_127 */ - {MCSPI1_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_clk */ - {MCSPI1_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_somi */ - {MCSPI1_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_simo */ - {MCSPI1_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_cs0 */ - {MCSPI1_CS1, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* mcspi1_cs1 */ - {MCSPI1_CS2, (PTU | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_139 */ - {MCSPI1_CS3, (PTU | IEN | M3)}, /* gpio_140 */ - {SDMMC5_CLK, (PTU | IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* sdmmc5_clk */ - {SDMMC5_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_cmd */ - {SDMMC5_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat0 */ - {SDMMC5_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat1 */ - {SDMMC5_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat2 */ - {SDMMC5_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat3 */ - {MCSPI4_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_clk */ - {MCSPI4_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_simo */ - {MCSPI4_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_somi */ - {MCSPI4_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_cs0 */ - {UART4_RX, (IEN | M0)}, /* uart4_rx */ - {UART4_TX, (M0)}, /* uart4_tx */ - {USBB2_ULPITLL_CLK, (PTD | IEN | M3)}, /* gpio_157 */ - {USBB2_ULPITLL_STP, (IEN | M5)}, /* dispc2_data23 */ - {USBB2_ULPITLL_DIR, (IEN | M5)}, /* dispc2_data22 */ - {USBB2_ULPITLL_NXT, (IEN | M5)}, /* dispc2_data21 */ - {USBB2_ULPITLL_DAT0, (IEN | M5)}, /* dispc2_data20 */ - {USBB2_ULPITLL_DAT1, (IEN | M5)}, /* dispc2_data19 */ - {USBB2_ULPITLL_DAT2, (IEN | M5)}, /* dispc2_data18 */ - {USBB2_ULPITLL_DAT3, (IEN | M5)}, /* dispc2_data15 */ - {USBB2_ULPITLL_DAT4, (IEN | M5)}, /* dispc2_data14 */ - {USBB2_ULPITLL_DAT5, (IEN | M5)}, /* dispc2_data13 */ - {USBB2_ULPITLL_DAT6, (IEN | M5)}, /* dispc2_data12 */ - {USBB2_ULPITLL_DAT7, (IEN | M5)}, /* dispc2_data11 */ - {USBB2_HSIC_DATA, (PTD | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_169 */ - {USBB2_HSIC_STROBE, (PTD | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_170 */ - {UNIPRO_TX0, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col0 */ - {UNIPRO_TY0, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col1 */ - {UNIPRO_TX1, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col2 */ - {UNIPRO_TY1, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col3 */ - {UNIPRO_TX2, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col4 */ - {UNIPRO_TY2, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col5 */ - {UNIPRO_RX0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row0 */ - {UNIPRO_RY0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row1 */ - {UNIPRO_RX1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row2 */ - {UNIPRO_RY1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row3 */ - {UNIPRO_RX2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row4 */ - {UNIPRO_RY2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row5 */ - {FREF_CLK1_OUT, (M0)}, /* fref_clk1_out */ - {FREF_CLK2_OUT, (M0)}, /* fref_clk2_out */ - {SYS_NIRQ1, (PTU | IEN | M0)}, /* sys_nirq1 */ - {SYS_NIRQ2, (M7)}, /* sys_nirq2 */ - {SYS_BOOT0, (PTU | IEN | M3)}, /* gpio_184 */ - {SYS_BOOT1, (M3)}, /* gpio_185 */ - {SYS_BOOT2, (PTD | IEN | M3)}, /* gpio_186 */ - {SYS_BOOT3, (PTD | IEN | M3)}, /* gpio_187 */ - {SYS_BOOT4, (M3)}, /* gpio_188 */ - {SYS_BOOT5, (PTD | IEN | M3)}, /* gpio_189 */ - {DPM_EMU0, (IEN | M0)}, /* dpm_emu0 */ - {DPM_EMU1, (IEN | M0)}, /* dpm_emu1 */ - {DPM_EMU2, (IEN | M0)}, /* dpm_emu2 */ - {DPM_EMU3, (IEN | M5)}, /* dispc2_data10 */ - {DPM_EMU4, (IEN | M5)}, /* dispc2_data9 */ - {DPM_EMU5, (IEN | M5)}, /* dispc2_data16 */ - {DPM_EMU6, (IEN | M5)}, /* dispc2_data17 */ - {DPM_EMU7, (IEN | M5)}, /* dispc2_hsync */ - {DPM_EMU8, (IEN | M5)}, /* dispc2_pclk */ - {DPM_EMU9, (IEN | M5)}, /* dispc2_vsync */ - {DPM_EMU10, (IEN | M5)}, /* dispc2_de */ - {DPM_EMU11, (IEN | M5)}, /* dispc2_data8 */ - {DPM_EMU12, (IEN | M5)}, /* dispc2_data7 */ - {DPM_EMU13, (IEN | M5)}, /* dispc2_data6 */ - {DPM_EMU14, (IEN | M5)}, /* dispc2_data5 */ - {DPM_EMU15, (IEN | M5)}, /* dispc2_data4 */ - {DPM_EMU16, (M3)}, /* gpio_27 */ - {DPM_EMU17, (IEN | M5)}, /* dispc2_data2 */ - {DPM_EMU18, (IEN | M5)}, /* dispc2_data1 */ - {DPM_EMU19, (IEN | M5)}, /* dispc2_data0 */ - {I2C1_SCL, (PTU | IEN | M0)}, /* i2c1_scl */ - {I2C1_SDA, (PTU | IEN | M0)}, /* i2c1_sda */ - {I2C2_SCL, (PTU | IEN | M0)}, /* i2c2_scl */ - {I2C2_SDA, (PTU | IEN | M0)}, /* i2c2_sda */ - {I2C3_SCL, (PTU | IEN | M0)}, /* i2c3_scl */ - {I2C3_SDA, (PTU | IEN | M0)}, /* i2c3_sda */ - {I2C4_SCL, (PTU | IEN | M0)}, /* i2c4_scl */ - {I2C4_SDA, (PTU | IEN | M0)} /* i2c4_sda */ - -}; - -const struct pad_conf_entry wkup_padconf_array_non_essential[] = { - {PAD0_SIM_IO, (IEN | M0)}, /* sim_io */ - {PAD1_SIM_CLK, (M0)}, /* sim_clk */ - {PAD0_SIM_RESET, (M0)}, /* sim_reset */ - {PAD1_SIM_CD, (PTU | IEN | M0)}, /* sim_cd */ - {PAD0_SIM_PWRCTRL, (M0)}, /* sim_pwrctrl */ - {PAD1_FREF_XTAL_IN, (M0)}, /* # */ - {PAD0_FREF_SLICER_IN, (M0)}, /* fref_slicer_in */ - {PAD1_FREF_CLK_IOREQ, (M0)}, /* fref_clk_ioreq */ - {PAD0_FREF_CLK0_OUT, (M2)}, /* sys_drm_msecure */ - {PAD1_FREF_CLK3_REQ, (M3)}, /* gpio_wk30 - Debug led-1 */ - {PAD0_FREF_CLK3_OUT, (M0)}, /* fref_clk3_out */ - {PAD0_FREF_CLK4_OUT, (M3)}, /* gpio_wk8 - Debug led-3 */ - {PAD0_SYS_NRESPWRON, (M0)}, /* sys_nrespwron */ - {PAD1_SYS_NRESWARM, (M0)}, /* sys_nreswarm */ - {PAD0_SYS_PWR_REQ, (PTU | M0)}, /* sys_pwr_req */ - {PAD1_SYS_PWRON_RESET, (M3)}, /* gpio_wk29 */ - {PAD0_SYS_BOOT6, (IEN | M3)}, /* gpio_wk9 */ - {PAD1_SYS_BOOT7, (IEN | M3)}, /* gpio_wk10 */ -}; - -const struct pad_conf_entry wkup_padconf_array_non_essential_4430[] = { - {PAD1_FREF_CLK4_REQ, (M3)} /* gpio_wk7 - Debug led-2 */ -}; - #endif /* _SDP4430_MUX_DATA_H */ -- 1.7.4.1

2 1

[U-Boot] [PATCH 1/2] ARM: OMAP4/5: Remove dead code against CONFIG_SYS_CLOCKS_ENABLE_ALL
by Jassi Brar 24 Jan '14

24 Jan '14

The commit f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls" removed the config option aimed towards moving that stuff into kernel, which renders some code unreachable. Remove that code. Signed-off-by: Jassi Brar <jaswinder.singh(a)linaro.org> --- Hi, The commit f3f98bb0 seems to suggest we want to move these settings into the kernel, but perhaps we should also evaluate the option of making these inits fully board specific but in u-boot? Thanks. arch/arm/cpu/armv7/omap-common/clocks-common.c | 47 ------------- arch/arm/cpu/armv7/omap4/clocks.c | 84 ----------------------- arch/arm/cpu/armv7/omap5/clocks.c | 87 ------------------------ arch/arm/include/asm/arch-omap4/clocks.h | 1 - arch/arm/include/asm/arch-omap5/clocks.h | 1 - 5 files changed, 0 insertions(+), 220 deletions(-) diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c index b1fd277..fc14465 100644 --- a/arch/arm/cpu/armv7/omap-common/clocks-common.c +++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c @@ -326,49 +326,6 @@ static void setup_dplls(void) #endif } -#ifdef CONFIG_SYS_CLOCKS_ENABLE_ALL -static void setup_non_essential_dplls(void) -{ - u32 abe_ref_clk; - const struct dpll_params *params; - - /* IVA */ - clrsetbits_le32(&prcm->cm_bypclk_dpll_iva, - CM_BYPCLK_DPLL_IVA_CLKSEL_MASK, DPLL_IVA_CLKSEL_CORE_X2_DIV_2); - - params = get_iva_dpll_params(); - do_setup_dpll(&prcm->cm_clkmode_dpll_iva, params, DPLL_LOCK, "iva"); - - /* Configure ABE dpll */ - params = get_abe_dpll_params(); -#ifdef CONFIG_SYS_OMAP_ABE_SYSCK - abe_ref_clk = CM_ABE_PLL_REF_CLKSEL_CLKSEL_SYSCLK; -#else - abe_ref_clk = CM_ABE_PLL_REF_CLKSEL_CLKSEL_32KCLK; - /* - * We need to enable some additional options to achieve - * 196.608MHz from 32768 Hz - */ - setbits_le32(&prcm->cm_clkmode_dpll_abe, - CM_CLKMODE_DPLL_DRIFTGUARD_EN_MASK| - CM_CLKMODE_DPLL_RELOCK_RAMP_EN_MASK| - CM_CLKMODE_DPLL_LPMODE_EN_MASK| - CM_CLKMODE_DPLL_REGM4XEN_MASK); - /* Spend 4 REFCLK cycles at each stage */ - clrsetbits_le32(&prcm->cm_clkmode_dpll_abe, - CM_CLKMODE_DPLL_RAMP_RATE_MASK, - 1 << CM_CLKMODE_DPLL_RAMP_RATE_SHIFT); -#endif - - /* Select the right reference clk */ - clrsetbits_le32(&prcm->cm_abe_pll_ref_clksel, - CM_ABE_PLL_REF_CLKSEL_CLKSEL_MASK, - abe_ref_clk << CM_ABE_PLL_REF_CLKSEL_CLKSEL_SHIFT); - /* Lock the dpll */ - do_setup_dpll(&prcm->cm_clkmode_dpll_abe, params, DPLL_LOCK, "abe"); -} -#endif - void do_scale_tps62361(int gpio, u32 reg, u32 volt_mv) { u32 step; @@ -584,10 +541,6 @@ void prcm_init(void) enable_basic_clocks(); scale_vcores(); setup_dplls(); -#ifdef CONFIG_SYS_CLOCKS_ENABLE_ALL - setup_non_essential_dplls(); - enable_non_essential_clocks(); -#endif break; default: break; diff --git a/arch/arm/cpu/armv7/omap4/clocks.c b/arch/arm/cpu/armv7/omap4/clocks.c index 5bd0a88..b3fc652 100644 --- a/arch/arm/cpu/armv7/omap4/clocks.c +++ b/arch/arm/cpu/armv7/omap4/clocks.c @@ -431,87 +431,3 @@ void enable_basic_uboot_clocks(void) clk_modules_explicit_en_essential, 1); } - -/* - * Enable non-essential clock domains, modules and - * do some additional special settings needed - */ -void enable_non_essential_clocks(void) -{ - u32 *const clk_domains_non_essential[] = { - &prcm->cm_mpu_m3_clkstctrl, - &prcm->cm_ivahd_clkstctrl, - &prcm->cm_dsp_clkstctrl, - &prcm->cm_dss_clkstctrl, - &prcm->cm_sgx_clkstctrl, - &prcm->cm1_abe_clkstctrl, - &prcm->cm_c2c_clkstctrl, - &prcm->cm_cam_clkstctrl, - &prcm->cm_dss_clkstctrl, - &prcm->cm_sdma_clkstctrl, - 0 - }; - - u32 *const clk_modules_hw_auto_non_essential[] = { - &prcm->cm_l3instr_l3_3_clkctrl, - &prcm->cm_l3instr_l3_instr_clkctrl, - &prcm->cm_l3instr_intrconn_wp1_clkctrl, - &prcm->cm_l3init_hsi_clkctrl, - 0 - }; - - u32 *const clk_modules_explicit_en_non_essential[] = { - &prcm->cm1_abe_aess_clkctrl, - &prcm->cm1_abe_pdm_clkctrl, - &prcm->cm1_abe_dmic_clkctrl, - &prcm->cm1_abe_mcasp_clkctrl, - &prcm->cm1_abe_mcbsp1_clkctrl, - &prcm->cm1_abe_mcbsp2_clkctrl, - &prcm->cm1_abe_mcbsp3_clkctrl, - &prcm->cm1_abe_slimbus_clkctrl, - &prcm->cm1_abe_timer5_clkctrl, - &prcm->cm1_abe_timer6_clkctrl, - &prcm->cm1_abe_timer7_clkctrl, - &prcm->cm1_abe_timer8_clkctrl, - &prcm->cm1_abe_wdt3_clkctrl, - &prcm->cm_l4per_gptimer9_clkctrl, - &prcm->cm_l4per_gptimer10_clkctrl, - &prcm->cm_l4per_gptimer11_clkctrl, - &prcm->cm_l4per_gptimer3_clkctrl, - &prcm->cm_l4per_gptimer4_clkctrl, - &prcm->cm_l4per_hdq1w_clkctrl, - &prcm->cm_l4per_mcbsp4_clkctrl, - &prcm->cm_l4per_mcspi2_clkctrl, - &prcm->cm_l4per_mcspi3_clkctrl, - &prcm->cm_l4per_mcspi4_clkctrl, - &prcm->cm_l4per_mmcsd3_clkctrl, - &prcm->cm_l4per_mmcsd4_clkctrl, - &prcm->cm_l4per_mmcsd5_clkctrl, - &prcm->cm_l4per_uart1_clkctrl, - &prcm->cm_l4per_uart2_clkctrl, - &prcm->cm_l4per_uart4_clkctrl, - &prcm->cm_wkup_keyboard_clkctrl, - &prcm->cm_wkup_wdtimer2_clkctrl, - &prcm->cm_cam_iss_clkctrl, - &prcm->cm_cam_fdif_clkctrl, - &prcm->cm_dss_dss_clkctrl, - &prcm->cm_sgx_sgx_clkctrl, - 0 - }; - - /* Enable optional functional clock for ISS */ - setbits_le32(&prcm->cm_cam_iss_clkctrl, ISS_CLKCTRL_OPTFCLKEN_MASK); - - /* Enable all optional functional clocks of DSS */ - setbits_le32(&prcm->cm_dss_dss_clkctrl, DSS_CLKCTRL_OPTFCLKEN_MASK); - - do_enable_clocks(clk_domains_non_essential, - clk_modules_hw_auto_non_essential, - clk_modules_explicit_en_non_essential, - 0); - - /* Put camera module in no sleep mode */ - clrsetbits_le32(&prcm->cm_cam_clkstctrl, MODULE_CLKCTRL_MODULEMODE_MASK, - CD_CLKCTRL_CLKTRCTRL_NO_SLEEP << - MODULE_CLKCTRL_MODULEMODE_SHIFT); -} diff --git a/arch/arm/cpu/armv7/omap5/clocks.c b/arch/arm/cpu/armv7/omap5/clocks.c index eecfbad..6c5441f 100644 --- a/arch/arm/cpu/armv7/omap5/clocks.c +++ b/arch/arm/cpu/armv7/omap5/clocks.c @@ -405,90 +405,3 @@ void enable_basic_uboot_clocks(void) clk_modules_explicit_en_essential, 1); } - -/* - * Enable non-essential clock domains, modules and - * do some additional special settings needed - */ -void enable_non_essential_clocks(void) -{ - u32 *const clk_domains_non_essential[] = { - &prcm->cm_mpu_m3_clkstctrl, - &prcm->cm_ivahd_clkstctrl, - &prcm->cm_dsp_clkstctrl, - &prcm->cm_dss_clkstctrl, - &prcm->cm_sgx_clkstctrl, - &prcm->cm1_abe_clkstctrl, - &prcm->cm_c2c_clkstctrl, - &prcm->cm_cam_clkstctrl, - &prcm->cm_dss_clkstctrl, - &prcm->cm_sdma_clkstctrl, - 0 - }; - - u32 *const clk_modules_hw_auto_non_essential[] = { - &prcm->cm_mpu_m3_mpu_m3_clkctrl, - &prcm->cm_ivahd_ivahd_clkctrl, - &prcm->cm_ivahd_sl2_clkctrl, - &prcm->cm_dsp_dsp_clkctrl, - &prcm->cm_l3instr_l3_3_clkctrl, - &prcm->cm_l3instr_l3_instr_clkctrl, - &prcm->cm_l3instr_intrconn_wp1_clkctrl, - &prcm->cm_l3init_hsi_clkctrl, - &prcm->cm_l4per_hdq1w_clkctrl, - 0 - }; - - u32 *const clk_modules_explicit_en_non_essential[] = { - &prcm->cm1_abe_aess_clkctrl, - &prcm->cm1_abe_pdm_clkctrl, - &prcm->cm1_abe_dmic_clkctrl, - &prcm->cm1_abe_mcasp_clkctrl, - &prcm->cm1_abe_mcbsp1_clkctrl, - &prcm->cm1_abe_mcbsp2_clkctrl, - &prcm->cm1_abe_mcbsp3_clkctrl, - &prcm->cm1_abe_slimbus_clkctrl, - &prcm->cm1_abe_timer5_clkctrl, - &prcm->cm1_abe_timer6_clkctrl, - &prcm->cm1_abe_timer7_clkctrl, - &prcm->cm1_abe_timer8_clkctrl, - &prcm->cm1_abe_wdt3_clkctrl, - &prcm->cm_l4per_gptimer9_clkctrl, - &prcm->cm_l4per_gptimer10_clkctrl, - &prcm->cm_l4per_gptimer11_clkctrl, - &prcm->cm_l4per_gptimer3_clkctrl, - &prcm->cm_l4per_gptimer4_clkctrl, - &prcm->cm_l4per_mcspi2_clkctrl, - &prcm->cm_l4per_mcspi3_clkctrl, - &prcm->cm_l4per_mcspi4_clkctrl, - &prcm->cm_l4per_mmcsd3_clkctrl, - &prcm->cm_l4per_mmcsd4_clkctrl, - &prcm->cm_l4per_mmcsd5_clkctrl, - &prcm->cm_l4per_uart1_clkctrl, - &prcm->cm_l4per_uart2_clkctrl, - &prcm->cm_l4per_uart4_clkctrl, - &prcm->cm_wkup_keyboard_clkctrl, - &prcm->cm_wkup_wdtimer2_clkctrl, - &prcm->cm_cam_iss_clkctrl, - &prcm->cm_cam_fdif_clkctrl, - &prcm->cm_dss_dss_clkctrl, - &prcm->cm_sgx_sgx_clkctrl, - 0 - }; - - /* Enable optional functional clock for ISS */ - setbits_le32(&prcm->cm_cam_iss_clkctrl, ISS_CLKCTRL_OPTFCLKEN_MASK); - - /* Enable all optional functional clocks of DSS */ - setbits_le32(&prcm->cm_dss_dss_clkctrl, DSS_CLKCTRL_OPTFCLKEN_MASK); - - do_enable_clocks(clk_domains_non_essential, - clk_modules_hw_auto_non_essential, - clk_modules_explicit_en_non_essential, - 0); - - /* Put camera module in no sleep mode */ - clrsetbits_le32(&prcm->cm_cam_clkstctrl, MODULE_CLKCTRL_MODULEMODE_MASK, - CD_CLKCTRL_CLKTRCTRL_NO_SLEEP << - MODULE_CLKCTRL_MODULEMODE_SHIFT); -} diff --git a/arch/arm/include/asm/arch-omap4/clocks.h b/arch/arm/include/asm/arch-omap4/clocks.h index be20fc0..eff7d02 100644 --- a/arch/arm/include/asm/arch-omap4/clocks.h +++ b/arch/arm/include/asm/arch-omap4/clocks.h @@ -753,7 +753,6 @@ void setup_post_dividers(u32 *const base, const struct dpll_params *params); u32 get_sys_clk_index(void); void enable_basic_clocks(void); void enable_basic_uboot_clocks(void); -void enable_non_essential_clocks(void); void do_enable_clocks(u32 *const *clk_domains, u32 *const *clk_modules_hw_auto, u32 *const *clk_modules_explicit_en, diff --git a/arch/arm/include/asm/arch-omap5/clocks.h b/arch/arm/include/asm/arch-omap5/clocks.h index 5f1a7aa..4f387a7 100644 --- a/arch/arm/include/asm/arch-omap5/clocks.h +++ b/arch/arm/include/asm/arch-omap5/clocks.h @@ -726,7 +726,6 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv); void setup_post_dividers(u32 *const base, const struct dpll_params *params); u32 get_sys_clk_index(void); void enable_basic_clocks(void); -void enable_non_essential_clocks(void); void enable_basic_uboot_clocks(void); void do_enable_clocks(u32 *const *clk_domains, u32 *const *clk_modules_hw_auto, -- 1.7.4.1

3 2