February 2013 - U-Boot

[U-Boot] [PATCH] nand/fsl_elbc: detect page size at runtime
by Scott Wood 22 May '13

22 May '13

This avoids needing a separate U-Boot config when some revisions of a board have small-page NAND and other revisions have large-page NAND (except for NAND SPL targets). CONFIG_FSL_ELBC_FMR is removed -- it was never used nor documented, and it gets in the way of this change. Signed-off-by: Scott Wood <scottwood(a)freescale.com> --- drivers/mtd/nand/fsl_elbc_nand.c | 39 +++++++++++++++++++++----------------- 1 file changed, 22 insertions(+), 17 deletions(-) diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c index 834a8a6..fb34d12 100644 --- a/drivers/mtd/nand/fsl_elbc_nand.c +++ b/drivers/mtd/nand/fsl_elbc_nand.c @@ -756,20 +756,8 @@ static int fsl_elbc_chip_init(int devnum, u8 *addr) nand->ecc.read_page = fsl_elbc_read_page; nand->ecc.write_page = fsl_elbc_write_page; -#ifdef CONFIG_FSL_ELBC_FMR - priv->fmr = CONFIG_FSL_ELBC_FMR; -#else priv->fmr = (15 << FMR_CWTO_SHIFT) | (2 << FMR_AL_SHIFT); - /* - * Hardware expects small page has ECCM0, large page has ECCM1 - * when booting from NAND. Board config can override if not - * booting from NAND. - */ - if (or & OR_FCM_PGS) - priv->fmr |= FMR_ECCM; -#endif - /* If CS Base Register selects full hardware ECC then use it */ if ((br & BR_DECC) == BR_DECC_CHK_GEN) { nand->ecc.mode = NAND_ECC_HW; @@ -786,11 +774,26 @@ static int fsl_elbc_chip_init(int devnum, u8 *addr) nand->ecc.mode = NAND_ECC_SOFT; } + ret = nand_scan_ident(mtd, 1, NULL); + if (ret) + return ret; + /* Large-page-specific setup */ - if (or & OR_FCM_PGS) { + if (mtd->writesize == 2048) { + setbits_be32(&elbc_ctrl->regs->bank[priv->bank].or, + OR_FCM_PGS); + in_be32(&elbc_ctrl->regs->bank[priv->bank].or); + priv->page_size = 1; nand->badblock_pattern = &largepage_memorybased; + /* + * Hardware expects small page has ECCM0, large page has + * ECCM1 when booting from NAND, and we follow that even + * when not booting from NAND. + */ + priv->fmr |= FMR_ECCM; + /* adjust ecc setup if needed */ if ((br & BR_DECC) == BR_DECC_CHK_GEN) { nand->ecc.steps = 4; @@ -798,12 +801,14 @@ static int fsl_elbc_chip_init(int devnum, u8 *addr) &fsl_elbc_oob_lp_eccm1 : &fsl_elbc_oob_lp_eccm0; } + } else if (mtd->writesize == 512) { + clrbits_be32(&elbc_ctrl->regs->bank[priv->bank].or, + OR_FCM_PGS); + in_be32(&elbc_ctrl->regs->bank[priv->bank].or); + } else { + return -ENODEV; } - ret = nand_scan_ident(mtd, 1, NULL); - if (ret) - return ret; - ret = nand_scan_tail(mtd); if (ret) return ret; -- 1.7.9.5

1 1

[U-Boot] [PATCH 0/4] Fix fixup_silent_linux() buffer overrun
by Doug Anderson 22 May '13

22 May '13

This set of patches together fixes a buffer overrun in the fixup_silent_linux() function when we've got a long linux command line. It also adds the removal of "earlyprintk" when we are silencing the linux console. One thing you will notice is that some of these changes have unit tests assocated with them. I wasn't sure exactly where these should live. If people would prefer them elsewhere (or simply removed), just let me know and I'll resubmit. Doug Anderson (4): cmdline: Add linux command line munging tools cosmetic: Fixup fixup_silent_linux() for checkpatch bootm: Avoid 256-byte overflow in fixup_silent_linux() bootm: Add earlyprintk to fixup_silent_linux common/Makefile | 1 + common/cmd_bootm.c | 136 +++++++++++++++++++---- common/cmdline.c | 318 ++++++++++++++++++++++++++++++++++++++++++++++++++++ include/cmdline.h | 30 +++++ 4 files changed, 465 insertions(+), 20 deletions(-) create mode 100644 common/cmdline.c create mode 100644 include/cmdline.h -- 1.7.3.1

4 38

[U-Boot] [PATCH 1/3] fw_env: fix type of len
by Mike Frysinger 21 May '13

21 May '13

This variable is assigned by a size_t, and is printed that way, but is incorrectly declared as an int. Which means we get warnings: fw_env.c: In function 'fw_setenv': fw_env.c:409:5: warning: format '%zu' expects argument of type 'size_t', but argument 3 has type 'int' [-Wformat] Signed-off-by: Mike Frysinger <vapier(a)gentoo.org> --- tools/env/fw_env.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/tools/env/fw_env.c b/tools/env/fw_env.c index 9b023e8..02f97c0 100644 --- a/tools/env/fw_env.c +++ b/tools/env/fw_env.c @@ -379,7 +379,8 @@ int fw_env_write(char *name, char *value) */ int fw_setenv(int argc, char *argv[]) { - int i, len; + int i; + size_t len; char *name; char *value = NULL; -- 1.7.12.4

6 11

[U-Boot] [PATCH] arm: pxa: Add support for ICP DAS LP-8x4x
by Sergey Yanovich 21 May '13

21 May '13

LP-8x4x is a programmable automation controller by ICP DAS. It is shipped with outdated U-Boot v1.3.0 This patch adds enough supports to boot the board: - 128M of 128M SDRAM - 32M of 48M NOR Flash memory - 1 of 4 Serial console (PXA FFUART) - 1 of 2 Ethernet controller (DM9000) Signed-off-by: Sergey Yanovich <ynvich(a)gmail.com> --- arch/arm/include/asm/mach-types.h | 13 ++ board/icpdas/lp8x4x/Makefile | 41 ++++++ board/icpdas/lp8x4x/lp8x4x.c | 133 ++++++++++++++++++ boards.cfg | 1 + include/configs/lp8x4x.h | 272 +++++++++++++++++++++++++++++++++++++ 5 files changed, 460 insertions(+) create mode 100644 board/icpdas/lp8x4x/Makefile create mode 100644 board/icpdas/lp8x4x/lp8x4x.c create mode 100644 include/configs/lp8x4x.h diff --git a/arch/arm/include/asm/mach-types.h b/arch/arm/include/asm/mach-types.h index a676b6d..644b937 100644 --- a/arch/arm/include/asm/mach-types.h +++ b/arch/arm/include/asm/mach-types.h @@ -1107,6 +1107,7 @@ extern unsigned int __machine_arch_type; #define MACH_TYPE_OMAP5_SEVM 3777 #define MACH_TYPE_ARMADILLO_800EVA 3863 #define MACH_TYPE_KZM9G 4140 +#define MACH_TYPE_LP8X4X 4539 #ifdef CONFIG_ARCH_EBSA110 # ifdef machine_arch_type @@ -14248,6 +14249,18 @@ extern unsigned int __machine_arch_type; # define machine_is_kzm9g() (0) #endif +#ifdef CONFIG_MACH_LP8X4X +# ifdef machine_arch_type +# undef machine_arch_type +# define machine_arch_type __machine_arch_type +# else +# define machine_arch_type MACH_TYPE_LP8X4X +# endif +# define machine_is_lp8x4x() (machine_arch_type == MACH_TYPE_LP8X4X) +#else +# define machine_is_lp8x4x() (0) +#endif + /* * These have not yet been registered */ diff --git a/board/icpdas/lp8x4x/Makefile b/board/icpdas/lp8x4x/Makefile new file mode 100644 index 0000000..cbe6aa9 --- /dev/null +++ b/board/icpdas/lp8x4x/Makefile @@ -0,0 +1,41 @@ +# +# ICPDAS LP-8x4x Support +# +# Copyright (C) 2013 Sergey Yanovich <ynvich(a)gmail.com> +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := lp8x4x.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/icpdas/lp8x4x/lp8x4x.c b/board/icpdas/lp8x4x/lp8x4x.c new file mode 100644 index 0000000..abdb84a --- /dev/null +++ b/board/icpdas/lp8x4x/lp8x4x.c @@ -0,0 +1,133 @@ +/* + * ICP DAS LP-8x4x Support + * + * Copyright (C) 2010 Marek Vasut <marek.vasut(a)gmail.com> + * adapted from Voipac PXA270 Support by + * Copyright (C) 2013 Sergey Yanovich <ynvich(a)gmail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/arch/hardware.h> +#include <asm/arch/regs-mmc.h> +#include <asm/arch/pxa.h> +#include <netdev.h> +#include <serial.h> +#include <asm/io.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Miscelaneous platform dependent initialisations + */ +int board_init(void) +{ + /* We have RAM, disable cache */ + dcache_disable(); + icache_disable(); + + /* memory and cpu-speed are setup before relocation */ + /* so we do _nothing_ here */ + + /* Arch number of lp8x4x */ + gd->bd->bi_arch_number = MACH_TYPE_LP8X4X; + + /* adress of boot parameters */ + gd->bd->bi_boot_params = 0xa0000100; + + return 0; +} + +int dram_init(void) +{ + pxa2xx_dram_init(); + gd->ram_size = PHYS_SDRAM_1_SIZE; + return 0; +} + +void dram_init_banksize(void) +{ + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; +} + +#ifdef CONFIG_CMD_MMC +int board_mmc_init(bd_t *bis) +{ + pxa_mmc_register(0); + return 0; +} +#endif + +#ifdef CONFIG_CMD_USB +int usb_board_init(void) +{ + writel((UHCHR | UHCHR_PCPL | UHCHR_PSPL) & + ~(UHCHR_SSEP0 | UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSE), + UHCHR); + + writel(readl(UHCHR) | UHCHR_FSBIR, UHCHR); + + while (readl(UHCHR) & UHCHR_FSBIR) + ; + + writel(readl(UHCHR) & ~UHCHR_SSE, UHCHR); + writel((UHCHIE_UPRIE | UHCHIE_RWIE), UHCHIE); + + /* Clear any OTG Pin Hold */ + if (readl(PSSR) & PSSR_OTGPH) + writel(readl(PSSR) | PSSR_OTGPH, PSSR); + + writel(readl(UHCRHDA) & ~(0x200), UHCRHDA); + writel(readl(UHCRHDA) | 0x100, UHCRHDA); + + /* Set port power control mask bits, only 3 ports. */ + writel(readl(UHCRHDB) | (0x7<<17), UHCRHDB); + + /* enable port 2 */ + writel(readl(UP2OCR) | UP2OCR_HXOE | UP2OCR_HXS | + UP2OCR_DMPDE | UP2OCR_DPPDE, UP2OCR); + + return 0; +} + +void usb_board_init_fail(void) +{ + return; +} + +void usb_board_stop(void) +{ + writel(readl(UHCHR) | UHCHR_FHR, UHCHR); + udelay(11); + writel(readl(UHCHR) & ~UHCHR_FHR, UHCHR); + + writel(readl(UHCCOMS) | 1, UHCCOMS); + udelay(10); + + writel(readl(CKEN) & ~CKEN10_USBHOST, CKEN); + + return; +} +#endif + +#ifdef CONFIG_DRIVER_DM9000 +int board_eth_init(bd_t *bis) +{ + return dm9000_initialize(bis); +} +#endif diff --git a/boards.cfg b/boards.cfg index b1319aa..2ca437e 100644 --- a/boards.cfg +++ b/boards.cfg @@ -1123,5 +1123,6 @@ gr_ep2s60 sparc leon3 - gaisler grsim sparc leon3 - gaisler gr_xc3s_1500 sparc leon3 - gaisler coreboot-x86 x86 x86 coreboot chromebook-x86 coreboot coreboot:SYS_TEXT_BASE=0x01110000 +lp8x4x arm pxa lp8x4x icpdas # Target ARCH CPU Board name Vendor SoC Options ######################################################################################################################## diff --git a/include/configs/lp8x4x.h b/include/configs/lp8x4x.h new file mode 100644 index 0000000..57a8916 --- /dev/null +++ b/include/configs/lp8x4x.h @@ -0,0 +1,272 @@ +/* + * ICP DAS LP-8x4x configuration file + * + * Copyright (C) 2013 Sergey Yanovich <ynvich(a)gmail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Board Configuration Options + */ +#define CONFIG_CPU_PXA27X 1 /* Marvell PXA270 CPU */ +#define CONFIG_MACH_LP8X4X 1 /* ICP DAS LP-8x4x */ +#define CONFIG_SYS_TEXT_BASE 0x00000000 + +/* + * Environment settings + */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_EXTRA_ENV_SETTINGS \ + "ethaddr=00:c0:26:28:96:30\0" \ + "ipaddr=192.168.0.10\0" \ + "netmask=255.255.255.0\0" \ + "serverip=192.168.0.1\0" \ + "stdin=serial\0" \ + "stdout=serial\0" \ + "stderr=serial\0" + +#define CONFIG_SYS_MALLOC_LEN (128*1024) +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_BOOTCOMMAND \ + "mmcinfo; tftp a0008000 zImage; go a0008000;" + +#define CONFIG_BOOTARGS \ + "console=ttySA0,115200 mem=128M root=/dev/mmcblk0p1 rw" \ + "init=/sbin/init rootfstype=ext3" + +#define CONFIG_TIMESTAMP +#define CONFIG_BOOTDELAY 2 /* Autoboot delay */ +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_LZMA /* LZMA compression support */ +#define CONFIG_OF_LIBFDT + +/* + * Serial Console Configuration + */ +#define CONFIG_PXA_SERIAL +#define CONFIG_FFUART 1 +#define CONFIG_CONS_INDEX 3 +#define CONFIG_BAUDRATE 115200 + +/* + * Bootloader Components Configuration + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_NET +#define CONFIG_CMD_ENV +#undef CONFIG_CMD_IMLS +#define CONFIG_CMD_MMC +#define CONFIG_CMD_USB +#undef CONFIG_LCD +#undef CONFIG_CMD_IDE + +/* + * Networking Configuration + * chip on the ICPDAS LINPAC board + */ +#ifdef CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP + +#define CONFIG_DRIVER_DM9000 1 +#define CONFIG_DM9000_BASE 0x0C000000 +#define DM9000_IO 0x0C000000 +#define DM9000_DATA 0x0C004000 +#define CONFIG_NET_RETRY_COUNT 10 + +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#endif + +/* + * MMC Card Configuration + */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_PXA_MMC_GENERIC +#define CONFIG_CMD_FAT +#define CONFIG_CMD_EXT2 +#define CONFIG_DOS_PARTITION +#endif + +/* + * KGDB + */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* kgdb serial port speed */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * HUSH Shell Configuration + */ +#define CONFIG_SYS_HUSH_PARSER 1 + +#undef CONFIG_SYS_LONGHELP +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT "$ " +#else +#define CONFIG_SYS_PROMPT "=> " +#endif +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_DEVICE_NULLDEV 1 +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_AUTO_COMPLETE 1 + +/* + * Clock Configuration + */ +#define CONFIG_SYS_HZ 1000 /* Timer @ 3250000 Hz */ + +/* + * DRAM Map + */ +#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ +#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */ + +#define CONFIG_SYS_DRAM_BASE 0xa0000000 /* CS0 */ +#define CONFIG_SYS_DRAM_SIZE 0x08000000 /* 128 MB DRAM */ + +#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0xa0008000 +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +/* Use first 64kb bank of the internal SRAM */ +#define CONFIG_SYS_INIT_SP_ADDR 0x5c010000 + +/* + * NOR FLASH + */ +#define CONFIG_SYS_MONITOR_BASE 0x0 +#define CONFIG_SYS_MONITOR_LEN 0x40000 +#define CONFIG_ENV_ADDR \ + (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SIZE 0x40000 +#define CONFIG_ENV_SECT_SIZE 0x40000 + +#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ +#define PHYS_FLASH_2 0x02000000 /* Flash Bank #2 */ + +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER 1 + +#define CONFIG_SYS_MAX_FLASH_SECT (4 + 255) +#define CONFIG_SYS_MAX_FLASH_BANKS 2 +#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 } + +#define CONFIG_SYS_FLASH_ERASE_TOUT (25*CONFIG_SYS_HZ) +#define CONFIG_SYS_FLASH_WRITE_TOUT (25*CONFIG_SYS_HZ) + +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 +#define CONFIG_SYS_FLASH_PROTECTION 1 + +#define CONFIG_ENV_IS_IN_FLASH 1 + +/* + * GPIO settings + */ +#define CONFIG_SYS_GPSR0_VAL 0x08008004 +#define CONFIG_SYS_GPSR1_VAL 0x00cf0002 +#define CONFIG_SYS_GPSR2_VAL 0x0221c000 +#define CONFIG_SYS_GPSR3_VAL 0x00020000 + +#define CONFIG_SYS_GPCR0_VAL 0x0 +#define CONFIG_SYS_GPCR1_VAL 0x0000ab80 +#define CONFIG_SYS_GPCR2_VAL 0x0 +#define CONFIG_SYS_GPCR3_VAL 0x0 + +#define CONFIG_SYS_GPDR0_VAL 0xc0a18df4 +#define CONFIG_SYS_GPDR1_VAL 0xfcdfab83 +#define CONFIG_SYS_GPDR2_VAL 0x02e1ffff +#define CONFIG_SYS_GPDR3_VAL 0x00021b81 + +#define CONFIG_SYS_GAFR0_L_VAL 0x80000000 +#define CONFIG_SYS_GAFR0_U_VAL 0xa5e54018 +#define CONFIG_SYS_GAFR1_L_VAL 0x999a955a +#define CONFIG_SYS_GAFR1_U_VAL 0xaaa5a0aa +#define CONFIG_SYS_GAFR2_L_VAL 0xaaaaaaaa +#define CONFIG_SYS_GAFR2_U_VAL 0x55f0a402 +#define CONFIG_SYS_GAFR3_L_VAL 0x540a950c +#define CONFIG_SYS_GAFR3_U_VAL 0x00001599 + +#define CONFIG_SYS_PSSR_VAL 0x32 + +/* + * Clock settings + */ +#define CONFIG_SYS_CKEN 0x005002c0 +#define CONFIG_SYS_CCCR 0x02000290 + +/* + * Memory settings + */ +#define CONFIG_SYS_MSC0_VAL 0x2bd8aad2 +#define CONFIG_SYS_MSC1_VAL 0xb8c9b8dc +#define CONFIG_SYS_MSC2_VAL 0xfff9b8c9 +#define CONFIG_SYS_FLYCNFG_VAL 0x00010001 +#define CONFIG_SYS_MDREFR_VAL 0x2093e018 +#define CONFIG_SYS_MDCNFG_VAL 0x810009d1 +#define CONFIG_SYS_MDMRS_VAL 0x00220022 +#define CONFIG_SYS_SXCNFG_VAL 0x40044004 + +/* + * PCMCIA and CF Interfaces + */ +#define CONFIG_SYS_MECR_VAL 0x00000001 +#define CONFIG_SYS_MCMEM0_VAL 0x0000c497 +#define CONFIG_SYS_MCMEM1_VAL 0x0000c497 +#define CONFIG_SYS_MCATT0_VAL 0x0000c497 +#define CONFIG_SYS_MCATT1_VAL 0x0000c497 +#define CONFIG_SYS_MCIO0_VAL 0x00008407 +#define CONFIG_SYS_MCIO1_VAL 0x00008407 + +/* + * LCD + */ +#ifdef CONFIG_LCD +#define CONFIG_VOIPAC_LCD +#endif + +/* + * USB + */ +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_OHCI_NEW +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_BOARD_INIT +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 +#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x4C000000 +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "lp8x4x" +#define CONFIG_USB_STORAGE +#endif + +#endif /* __CONFIG_H */ -- 1.7.10.4

4 4

[U-Boot] [PATCH v1 1/2] blackfin: bf609: implement soft switch
by Sonic Zhang 13 May '13

13 May '13

From: Sonic Zhang <sonic.zhang(a)analog.com> Set up soft switch pins properly in board init code. Signed-off-by: Sonic Zhang <sonic.zhang(a)analog.com> Signed-off-by: Scott Jiang <scott.jiang(a)analog.com> Signed-off-by: Bob Liu <lliubbo(a)gmail.com> --- board/bf609-ezkit/soft_switch.c | 180 +++++++++++++++++++++++++++++++++++++++ board/bf609-ezkit/soft_switch.h | 71 +++++++++++++++ 2 files changed, 251 insertions(+), 0 deletions(-) create mode 100644 board/bf609-ezkit/soft_switch.c create mode 100644 board/bf609-ezkit/soft_switch.h diff --git a/board/bf609-ezkit/soft_switch.c b/board/bf609-ezkit/soft_switch.c new file mode 100644 index 0000000..2e1404f --- /dev/null +++ b/board/bf609-ezkit/soft_switch.c @@ -0,0 +1,180 @@ +/* + * U-boot - main board file + * + * Copyright (c) 2008-2011 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include <common.h> +#include <asm/blackfin.h> +#include <asm/io.h> +#include <i2c.h> +#include "soft_switch.h" + +#define SWITCH_ADDR 0x21 + +#define NUM_SWITCH 3 +#define IODIRA 0x0 +#define IODIRB 0x1 +#define OLATA 0x14 +#define OLATB 0x15 + +struct switch_config { + uchar dir0; /* IODIRA */ + uchar dir1; /* IODIRB */ + uchar value0; /* OLATA */ + uchar value1; /* OLATB */ +}; + +static struct switch_config switch_config_array[NUM_SWITCH] = { + { +/* + U45 Port A U45 Port B + + 7--------------- RMII_CLK_EN | 7--------------- ~TEMP_THERM_EN + | 6------------- ~CNT0ZM_EN | | 6------------- ~TEMP_IRQ_EN + | | 5----------- ~CNT0DG_EN | | | 5----------- ~UART0CTS_146_EN + | | | 4--------- ~CNT0UD_EN | | | | 4--------- ~UART0CTS_RST_EN + | | | | 3------- ~CAN0RX_EN | | | | | 3------- ~UART0CTS_RTS_LPBK + | | | | | 2----- ~CAN0_ERR_EN | | | | | | 2----- ~UART0CTS_EN + | | | | | | 1--- ~CAN_STB | | | | | | | 1--- ~UART0RX_EN + | | | | | | | 0- CAN_EN | | | | | | | | 0- ~UART0RTS_EN + | | | | | | | | | | | | | | | | | + O O O O O O O O | O O O O O O O O (I/O direction) + 1 0 0 0 0 0 1 1 | 1 1 1 1 1 0 0 0 (value being set) +*/ + .dir0 = 0x0, /* all output */ + .dir1 = 0x0, /* all output */ + .value0 = RMII_CLK_EN | CAN_STB | CAN_EN, + .value1 = TEMP_THERM_EN | TEMP_IRQ_EN | UART0CTS_146_EN + | UART0CTS_RST_EN | UART0CTS_RTS_LPBK, + }, + { +/* + U46 Port A U46 Port B + + 7--------------- ~LED4_GPIO_EN | 7--------------- EMPTY + | 6------------- ~LED3_GPIO_EN | | 6------------- ~SPI0D3_EN + | | 5----------- ~LED2_GPIO_EN | | | 5----------- ~SPI0D2_EN + | | | 4--------- ~LED1_GPIO_EN | | | | 4--------- ~SPIFLASH_CS_EN + | | | | 3------- SMC0_LP0_EN | | | | | 3------- ~SD_WP_EN + | | | | | 2----- EMPTY | | | | | | 2----- ~SD_CD_EN + | | | | | | 1--- SMC0_EPPI2 | | | | | | | 1--- ~PUSHBUTTON2_EN + _LP1_SWITCH + | | | | | | | 0- OVERRIDE_SMC0 | | | | | | | | 0- ~PUSHBUTTON1_EN + _LP0_BOOT + | | | | | | | | | | | | | | | | | + O O O O O O O O | O O O O O O O O (I/O direction) + 0 0 0 0 0 X 0 1 | X 0 0 0 0 0 0 0 (value being set) +*/ + .dir0 = 0x0, /* all output */ + .dir1 = 0x0, /* all output */ +#ifdef CONFIG_BFIN_LINKPORT + .value0 = OVERRIDE_SMC0_LP0_BOOT, +#else + .value0 = SMC0_EPPI2_LP1_SWITCH, +#endif + .value1 = 0x0, + }, + { +/* + U47 Port A U47 Port B + + 7--------------- ~PD2_SPI0MISO | 7--------------- EMPTY + _EI3_EN + | 6------------- ~PD1_SPI0D3 | | 6------------- EMPTY + _EPPI1D17 + _SPI0SEL2 + _EI3_EN + | | 5----------- ~PD0_SPI0D2 | | | 5----------- EMPTY + _EPPI1D16 + _SPI0SEL3 + _EI3_EN + | | | 4--------- ~WAKE_PUSH | | | | 4--------- EMPTY + BUTTON_EN + | | | | 3------- ~ETHERNET_EN | | | | | 3------- EMPTY + | | | | | 2----- PHYAD0 | | | | | | 2----- EMPTY + | | | | | | 1--- PHY_PWR | | | | | | | 1--- ~PD4_SPI0CK_EI3_EN + _DWN_INT + | | | | | | | 0- ~PHYINT_EN | | | | | | | | 0- ~PD3_SPI0MOSI_EI3_EN + | | | | | | | | | | | | | | | | | + O O O O O I I O | O O O O O O O O (I/O direction) + 1 1 1 0 0 0 0 0 | X X X X X X 1 1 (value being set) +*/ + .dir0 = 0x6, /* bits 1 and 2 input, all others output */ + .dir1 = 0x0, /* all output */ + .value0 = PD1_SPI0D3_EN | PD0_SPI0D2_EN, + .value1 = 0, + }, +}; + +static int setup_soft_switch(int addr, struct switch_config *config) +{ + int ret = 0; + + ret = i2c_write(addr, OLATA, 1, &config->value0, 1); + if (ret) + return ret; + ret = i2c_write(addr, OLATB, 1, &config->value1, 1); + if (ret) + return ret; + + ret = i2c_write(addr, IODIRA, 1, &config->dir0, 1); + if (ret) + return ret; + return i2c_write(addr, IODIRB, 1, &config->dir1, 1); +} + +int config_switch_bit(int num, int port, int bit, int dir, uchar value) +{ + int addr = SWITCH_ADDR + num; + int ret, data_reg, dir_reg; + uchar tmp; + + if (port == IO_PORT_A) { + data_reg = OLATA; + dir_reg = IODIRA; + } else { + data_reg = OLATB; + dir_reg = IODIRB; + } + + if (dir == IO_PORT_INPUT) { + ret = i2c_read(addr, dir_reg, 1, &tmp, 1); + if (ret) + return ret; + tmp |= bit; + return i2c_write(addr, dir_reg, 1, &tmp, 1); + } else { + ret = i2c_read(addr, data_reg, 1, &tmp, 1); + if (ret) + return ret; + if (value) + tmp |= bit; + else + tmp &= ~bit; + ret = i2c_write(addr, data_reg, 1, &tmp, 1); + if (ret) + return ret; + ret = i2c_read(addr, dir_reg, 1, &tmp, 1); + if (ret) + return ret; + tmp &= ~bit; + return i2c_write(addr, dir_reg, 1, &tmp, 1); + } +} + +int setup_board_switches(void) +{ + int ret; + int i; + + for (i = 0; i < NUM_SWITCH; i++) { + ret = setup_soft_switch(SWITCH_ADDR + i, + &switch_config_array[i]); + if (ret) + return ret; + } + return 0; +} diff --git a/board/bf609-ezkit/soft_switch.h b/board/bf609-ezkit/soft_switch.h new file mode 100644 index 0000000..8da0e44 --- /dev/null +++ b/board/bf609-ezkit/soft_switch.h @@ -0,0 +1,71 @@ +/* + * U-boot - main board file + * + * Copyright (c) 2008-2011 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef __SOFT_SWITCH_H__ +#define __SOFT_SWITCH_H__ + +/* switch 0 port A */ +#define CAN_EN 0x1 +#define CAN_STB 0x2 +#define CAN0_ERR_EN 0x4 +#define CAN0RX_EN 0x8 +#define CNT0UD_EN 0x10 +#define CNT0DG_EN 0x20 +#define CNT0ZM_EN 0x40 +#define RMII_CLK_EN 0x80 + +/* switch 0 port B */ +#define UART0RTS_EN 0x1 +#define UART0RX_EN 0x2 +#define UART0CTS_EN 0x4 +#define UART0CTS_RTS_LPBK 0x8 +#define UART0CTS_RST_EN 0x10 +#define UART0CTS_146_EN 0x20 +#define TEMP_IRQ_EN 0x40 +#define TEMP_THERM_EN 0x80 + +/* switch 1 port A */ +#define OVERRIDE_SMC0_LP0_BOOT 0x1 +#define SMC0_EPPI2_LP1_SWITCH 0x2 +#define SMC0_LP0_EN 0x8 +#define LED1_GPIO_EN 0x10 +#define LED2_GPIO_EN 0x20 +#define LED3_GPIO_EN 0x40 +#define LED4_GPIO_EN 0x80 + +/* switch 1 port B */ +#define PUSHBUTTON1_EN 0x1 +#define PUSHBUTTON2_EN 0x2 +#define SD_CD_EN 0x4 +#define SD_WP_EN 0x8 +#define SPIFLASH_CS_EN 0x10 +#define SPI0D2_EN 0x20 +#define SPI0D3_EN 0x40 + +/* switch 2 port A */ +#define PHYINT_EN 0x1 +#define PHY_PWR_DWN_INT 0x2 +#define PHYAD0 0x4 +#define ETHERNET_EN 0x8 +#define WAKE_PUSHBUTTON_EN 0x10 +#define PD0_SPI0D2_EN 0x20 +#define PD1_SPI0D3_EN 0x40 +#define PD2_SPI0MISO_EN 0x80 + +/* switch 2 port B */ +#define PD3_SPI0MOSI_EN 0x1 +#define PD4_SPI0CK_EN 0x2 + +#define IO_PORT_A 0 +#define IO_PORT_B 1 +#define IO_PORT_INPUT 0 +#define IO_PORT_OUTPUT 1 + +int config_switch_bit(int num, int port, int bit, int dir, uchar value); +int setup_board_switches(void); +#endif -- 1.7.0.4

2 3

[U-Boot] [PATCH v0] davinci, mmc: Added a delay reading ext CSD register
by Davide Bonfanti 06 May '13

06 May '13

Without this additional delay, some eMMC don't negotiate properly bus width Tested on: - Toshiba THGBM2G8D8FBAIB - Toshiba THGBM4G4D1HBAR - Micron MTFC4GMVEA (the one giving the problem) - Hynix H26M64002BNR - SanDisk SDIN5E1-32G Signed-off-by: Davide Bonfanti <davide.bonfanti(a)bticino.it> --- drivers/mmc/davinci_mmc.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/mmc/davinci_mmc.c b/drivers/mmc/davinci_mmc.c index ee8f261..d5a38a7 100644 --- a/drivers/mmc/davinci_mmc.c +++ b/drivers/mmc/davinci_mmc.c @@ -285,8 +285,11 @@ dmmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data) */ if (bytes_left > fifo_bytes) dmmc_wait_fifo_status(regs, 0x4a); - else if (bytes_left == fifo_bytes) + else if (bytes_left == fifo_bytes) { dmmc_wait_fifo_status(regs, 0x40); + if (cmd->cmdidx == MMC_CMD_SEND_EXT_CSD) + udelay(600); + } for (i = 0; bytes_left && (i < fifo_words); i++) { cmddata = get_val(&regs->mmcdrr); -- 1.7.9.5 Ce message, ainsi que tous les fichiers joints à ce message, peuvent contenir des informations sensibles et/ ou confidentielles ne devant pas être divulguées. Si vous n'êtes pas le destinataire de ce message (ou que vous recevez ce message par erreur), nous vous remercions de le notifier immédiatement à son expéditeur, et de détruire ce message. Toute copie, divulgation, modification, utilisation ou diffusion, non autorisée, directe ou indirecte, de tout ou partie de ce message, est strictement interdite. This e-mail, and any document attached hereby, may contain confidential and/or privileged information. If you are not the intended recipient (or have received this e-mail in error) please notify the sender immediately and destroy this e-mail. Any unauthorized, direct or indirect, copying, disclosure, distribution or other use of the material or parts thereof is strictly forbidden.

3 2

Re: [U-Boot] [PATCH] video: cfb_console: flush dcache for frame buffer in DRAM
by Eric Nelson 06 May '13

06 May '13

Hi Anatolij, I hate to come in late to the discussion, but while testing [1] with cache enabled, I started down the path of fixing up code paths within drivers/video/cfb_console.c that are followed by SABRE Lite as you did in [2]. [1] [PATCH V2 0/2] i.MX6: mx6qsabrelite: Add splash screen support http://lists.denx.de/pipermail/u-boot/2012-September/134241.html [2] [PATCH] video: cfb_console: flush dcache for frame buffer in DRAM http://lists.denx.de/pipermail/u-boot/2012-April/123333.html That code essentially looks like this: void video_drawchars(...) { ... switch (VIDEO_DATA_FORMAT) { case GDF__8BIT_INDEX: case GDF__8BIT_332RGB: case GDF_15BIT_555RGB: case GDF_16BIT_565RGB: ... cache not flushed in these cases case GDF_32BIT_X888RGB: ... cache is flushed here } SABRE Lite (ipu3) code happens to use the RGB565 frame buffer format, so it needs additional fixup. Continuing this pattern seems to be a mistake though. There are a lot of cases, with all sorts of different alignments (most of which won't sync with cache line boundaries) and it seems that there's little to no benefit in the fine granularity. It seems that by the time we fix up all of the individual spots where we're writing to a line in the frame buffer, the cache can never get dirty in the first place. It seems much more sensible to simply use flush_dcache_range() on the entire frame buffer in each of the public calls and let the MMU figure out what needs flushing. Is there something I'm missing? My other immediate thought was that we should really place the frame buffer in un-cacheable memory, but then we really will be doing more memory accesses. Please advise, Eric

2 3

[U-Boot] [PATCH] powerpc/mpc85xx: add setting of clock-frequency for mpic node
by Wang Dongsheng 02 May '13

02 May '13

Set the device tree property associated with the mpic source frequency. The frequency is used for mpic timer. Signed-off-by: Wang Dongsheng <dongsheng.wang(a)freescale.com> --- arch/powerpc/cpu/mpc85xx/fdt.c | 5 +++++ 1 files changed, 5 insertions(+), 0 deletions(-) diff --git a/arch/powerpc/cpu/mpc85xx/fdt.c b/arch/powerpc/cpu/mpc85xx/fdt.c index 3a268aa..f07d1cf 100644 --- a/arch/powerpc/cpu/mpc85xx/fdt.c +++ b/arch/powerpc/cpu/mpc85xx/fdt.c @@ -663,6 +663,11 @@ void ft_cpu_setup(void *blob, bd_t *bd) #ifdef CONFIG_FSL_CORENET do_fixup_by_compat_u32(blob, "fsl,qoriq-clockgen-1.0", "clock-frequency", CONFIG_SYS_CLK_FREQ, 1); + do_fixup_by_compat_u32(blob, "fsl,mpic", + "clock-frequency", get_bus_freq(0)/2, 1); +#else + do_fixup_by_compat_u32(blob, "fsl,mpic", + "clock-frequency", get_bus_freq(0), 1); #endif fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize); -- 1.7.5.1

2 4

[U-Boot] [PATCH v2] mmc: Split device init to decouple OCR-polling delay
by Simon Glass 29 Apr '13

29 Apr '13

From: Che-Liang Chiou <clchiou(a)chromium.org> Most of time that MMC driver spends on initializing a device is polling OCR (operation conditions register). To decouple this polling loop, device init is split into two parts: The first part fires the OCR query command, and the second part polls the result. So the caller is now no longer bound to the OCR-polling delay; he may fire the query, go somewhere and then come back later for the result. To use this, call mmc_set_preinit() on any device which needs this. This can save significant amounts of time on boot (e.g. 200ms) by hiding the MMC init time behind other init. Signed-off-by: Che-Liang Chiou <clchiou(a)chromium.org> Signed-off-by: Simon Glass <sjg(a)chromium.org> --- Changes in v2: - Rebase to master drivers/mmc/mmc.c | 137 ++++++++++++++++++++++++++++++++++++++++------------ include/mmc.h | 30 ++++++++++++ 2 files changed, 135 insertions(+), 32 deletions(-) diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c index 72e8ce6..09695e8 100644 --- a/drivers/mmc/mmc.c +++ b/drivers/mmc/mmc.c @@ -503,48 +503,70 @@ static int sd_send_op_cond(struct mmc *mmc) return 0; } -static int mmc_send_op_cond(struct mmc *mmc) +/* We pass in the cmd since otherwise the init seems to fail */ +static int mmc_send_op_cond_iter(struct mmc *mmc, struct mmc_cmd *cmd, + int use_arg) { - int timeout = 10000; - struct mmc_cmd cmd; int err; + cmd->cmdidx = MMC_CMD_SEND_OP_COND; + cmd->resp_type = MMC_RSP_R3; + cmd->cmdarg = 0; + if (use_arg && !mmc_host_is_spi(mmc)) { + cmd->cmdarg = + (mmc->voltages & + (mmc->op_cond_response & OCR_VOLTAGE_MASK)) | + (mmc->op_cond_response & OCR_ACCESS_MODE); + + if (mmc->host_caps & MMC_MODE_HC) + cmd->cmdarg |= OCR_HCS; + } + err = mmc_send_cmd(mmc, cmd, NULL); + if (err) + return err; + mmc->op_cond_response = cmd->response[0]; + return 0; +} + +int mmc_send_op_cond(struct mmc *mmc) +{ + struct mmc_cmd cmd; + int err, i; + /* Some cards seem to need this */ mmc_go_idle(mmc); /* Asking to the card its capabilities */ - cmd.cmdidx = MMC_CMD_SEND_OP_COND; - cmd.resp_type = MMC_RSP_R3; - cmd.cmdarg = 0; - - err = mmc_send_cmd(mmc, &cmd, NULL); + mmc->op_cond_pending = 1; + for (i = 0; i < 2; i++) { + err = mmc_send_op_cond_iter(mmc, &cmd, i != 0); + if (err) + return err; - if (err) - return err; + /* exit if not busy (flag seems to be inverted) */ + if (mmc->op_cond_response & OCR_BUSY) + return 0; + } + return IN_PROGRESS; +} - udelay(1000); +int mmc_complete_op_cond(struct mmc *mmc) +{ + struct mmc_cmd cmd; + int timeout = 1000; + uint start; + int err; + mmc->op_cond_pending = 0; + start = get_timer(0); do { - cmd.cmdidx = MMC_CMD_SEND_OP_COND; - cmd.resp_type = MMC_RSP_R3; - cmd.cmdarg = (mmc_host_is_spi(mmc) ? 0 : - (mmc->voltages & - (cmd.response[0] & OCR_VOLTAGE_MASK)) | - (cmd.response[0] & OCR_ACCESS_MODE)); - - if (mmc->host_caps & MMC_MODE_HC) - cmd.cmdarg |= OCR_HCS; - - err = mmc_send_cmd(mmc, &cmd, NULL); - + err = mmc_send_op_cond_iter(mmc, &cmd, 1); if (err) return err; - - udelay(1000); - } while (!(cmd.response[0] & OCR_BUSY) && timeout--); - - if (timeout <= 0) - return UNUSABLE_ERR; + if (get_timer(start) > timeout) + return UNUSABLE_ERR; + udelay(100); + } while (!(mmc->op_cond_response & OCR_BUSY)); if (mmc_host_is_spi(mmc)) { /* read OCR for spi */ cmd.cmdidx = MMC_CMD_SPI_READ_OCR; @@ -1227,7 +1249,7 @@ block_dev_desc_t *mmc_get_dev(int dev) } #endif -int mmc_init(struct mmc *mmc) +int mmc_start_init(struct mmc *mmc) { int err; @@ -1267,17 +1289,48 @@ int mmc_init(struct mmc *mmc) if (err == TIMEOUT) { err = mmc_send_op_cond(mmc); - if (err) { + if (err && err != IN_PROGRESS) { printf("Card did not respond to voltage select!\n"); return UNUSABLE_ERR; } } - err = mmc_startup(mmc); + if (err == IN_PROGRESS) + mmc->init_in_progress = 1; + + return err; +} + +static int mmc_complete_init(struct mmc *mmc) +{ + int err = 0; + + if (mmc->op_cond_pending) + err = mmc_complete_op_cond(mmc); + + if (!err) + err = mmc_startup(mmc); if (err) mmc->has_init = 0; else mmc->has_init = 1; + mmc->init_in_progress = 0; + return err; +} + +int mmc_init(struct mmc *mmc) +{ + int err = IN_PROGRESS; + unsigned start = get_timer(0); + + if (mmc->has_init) + return 0; + if (!mmc->init_in_progress) + err = mmc_start_init(mmc); + + if (!err || err == IN_PROGRESS) + err = mmc_complete_init(mmc); + debug("%s: %d, time %lu\n", __func__, err, get_timer(start)); return err; } @@ -1315,6 +1368,25 @@ int get_mmc_num(void) return cur_dev_num; } +void mmc_set_preinit(struct mmc *mmc, int preinit) +{ + mmc->preinit = preinit; +} + +static void do_preinit(void) +{ + struct mmc *m; + struct list_head *entry; + + list_for_each(entry, &mmc_devices) { + m = list_entry(entry, struct mmc, link); + + if (m->preinit) + mmc_start_init(m); + } +} + + int mmc_initialize(bd_t *bis) { INIT_LIST_HEAD (&mmc_devices); @@ -1325,5 +1397,6 @@ int mmc_initialize(bd_t *bis) print_mmc_devices(','); + do_preinit(); return 0; } diff --git a/include/mmc.h b/include/mmc.h index a13e2bd..445d714 100644 --- a/include/mmc.h +++ b/include/mmc.h @@ -62,6 +62,7 @@ #define UNUSABLE_ERR -17 /* Unusable Card */ #define COMM_ERR -18 /* Communications Error */ #define TIMEOUT -19 +#define IN_PROGRESS -20 /* operation is in progress */ #define MMC_CMD_GO_IDLE_STATE 0 #define MMC_CMD_SEND_OP_COND 1 @@ -260,6 +261,10 @@ struct mmc { int (*init)(struct mmc *mmc); int (*getcd)(struct mmc *mmc); uint b_max; + char op_cond_pending; /* 1 if we are waiting on an op_cond command */ + char init_in_progress; /* 1 if we have done mmc_start_init() */ + char preinit; /* start init as early as possible */ + uint op_cond_response; /* the response byte from the last op_cond */ }; int mmc_register(struct mmc *mmc); @@ -276,6 +281,31 @@ int mmc_switch_part(int dev_num, unsigned int part_num); int mmc_getcd(struct mmc *mmc); void spl_mmc_load(void) __noreturn; +/** + * Start device initialization and return immediately; it does not block on + * polling OCR (operation condition register) status. Then you should call + * mmc_init, which would block on polling OCR status and complete the device + * initializatin. + * + * @param mmc Pointer to a MMC device struct + * @return 0 on success, IN_PROGRESS on waiting for OCR status, <0 on error. + */ +int mmc_start_init(struct mmc *mmc); + +/** + * Set preinit flag of mmc device. + * + * This will cause the device to be pre-inited during mmc_initialize(), + * which may save boot time if the device is not accessed until later. + * Some eMMC devices take 200-300ms to init, but unfortunately they + * must be sent a series of commands to even get them to start preparing + * for operation. + * + * @param mmc Pointer to a MMC device struct + * @param preinit preinit flag value + */ +void mmc_set_preinit(struct mmc *mmc, int preinit); + #ifdef CONFIG_GENERIC_MMC #define mmc_host_is_spi(mmc) ((mmc)->host_caps & MMC_MODE_SPI) struct mmc *mmc_spi_init(uint bus, uint cs, uint speed, uint mode); -- 1.7.7.3

3 12

[U-Boot] [PATCH 1/3] ppc4xx: Add SPL support
by Stefan Roese 22 Apr '13

22 Apr '13

This patch adds SPL booting support (NOR flash) for the PPC4xx platforms. This SPL booting (Falcon mode) will be used by the upcoming lcd4_lwmon5 board port (lwmon5 variant). Signed-off-by: Stefan Roese <sr(a)denx.de> --- arch/powerpc/cpu/ppc4xx/Makefile | 4 ++ arch/powerpc/cpu/ppc4xx/start.S | 37 +++++++++++++++-- arch/powerpc/cpu/ppc4xx/u-boot-spl.lds | 74 ++++++++++++++++++++++++++++++++++ arch/powerpc/cpu/ppc4xx/u-boot.lds | 2 + 4 files changed, 113 insertions(+), 4 deletions(-) create mode 100644 arch/powerpc/cpu/ppc4xx/u-boot-spl.lds diff --git a/arch/powerpc/cpu/ppc4xx/Makefile b/arch/powerpc/cpu/ppc4xx/Makefile index 8da2f86..e301dc6 100644 --- a/arch/powerpc/cpu/ppc4xx/Makefile +++ b/arch/powerpc/cpu/ppc4xx/Makefile @@ -68,6 +68,10 @@ COBJS += miiphy.o COBJS += uic.o endif +ifdef CONFIG_SPL_BUILD +COBJS-y += spl_boot.o +endif + SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS) $(COBJS-y)) START := $(addprefix $(obj),$(START)) diff --git a/arch/powerpc/cpu/ppc4xx/start.S b/arch/powerpc/cpu/ppc4xx/start.S index 7aef43b..ae990cc 100644 --- a/arch/powerpc/cpu/ppc4xx/start.S +++ b/arch/powerpc/cpu/ppc4xx/start.S @@ -232,7 +232,7 @@ * * Use r12 to access the GOT */ -#if !defined(CONFIG_NAND_SPL) +#if !defined(CONFIG_NAND_SPL) && !defined(CONFIG_SPL_BUILD) START_GOT GOT_ENTRY(_GOT2_TABLE_) GOT_ENTRY(_FIXUP_TABLE_) @@ -248,7 +248,8 @@ END_GOT #endif /* CONFIG_NAND_SPL */ -#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) && \ + !defined(CONFIG_SPL_BUILD) /* * NAND U-Boot image is started from offset 0 */ @@ -270,6 +271,18 @@ bl _start_440 #endif +#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD) + /* + * This is the entry of the real U-Boot from a board port + * that supports SPL booting on the PPC4xx. We only need + * to call board_init_f() here. Everything else has already + * been done in the SPL u-boot version. + */ + GET_GOT /* initialize GOT access */ + bl board_init_f /* run 1st part of board init code (in Flash)*/ + /* NOTREACHED - board_init_f() does not return */ +#endif + /* * 440 Startup -- on reset only the top 4k of the effective * address space is mapped in by an entry in the instruction @@ -539,7 +552,7 @@ tlbnx2: addi r4,r4,1 /* Next TLB */ * r3 - 1st arg to board_init(): IMMP pointer * r4 - 2nd arg to board_init(): boot flag */ -#ifndef CONFIG_NAND_SPL +#if !defined(CONFIG_NAND_SPL) && !defined(CONFIG_SPL_BUILD) .text .long 0x27051956 /* U-Boot Magic Number */ .globl version_string @@ -612,6 +625,18 @@ _end_of_vectors: .globl _start _start: +#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD) + /* + * This is the entry of the real U-Boot from a board port + * that supports SPL booting on the PPC4xx. We only need + * to call board_init_f() here. Everything else has already + * been done in the SPL u-boot version. + */ + GET_GOT /* initialize GOT access */ + bl board_init_f /* run 1st part of board init code (in Flash)*/ + /* NOTREACHED - board_init_f() does not return */ +#endif + /*****************************************************************************/ #if defined(CONFIG_440) @@ -796,7 +821,9 @@ _start: #ifdef CONFIG_NAND_SPL bl nand_boot_common /* will not return */ #else +#ifndef CONFIG_SPL_BUILD GET_GOT +#endif bl cpu_init_f /* run low-level CPU init code (from Flash) */ bl board_init_f @@ -1080,7 +1107,7 @@ _start: /*----------------------------------------------------------------------- */ -#ifndef CONFIG_NAND_SPL +#if !defined(CONFIG_NAND_SPL) && !defined(CONFIG_SPL_BUILD) /* * This code finishes saving the registers to the exception frame * and jumps to the appropriate handler for the exception. @@ -1262,6 +1289,7 @@ in32r: lwbrx r3,r0,r3 blr +#if !defined(CONFIG_SPL_BUILD) /* * void relocate_code (addr_sp, gd, addr_moni) * @@ -1626,6 +1654,7 @@ __440_msr_continue: mtlr r4 /* restore link register */ blr +#endif /* CONFIG_SPL_BUILD */ #if defined(CONFIG_440) /*----------------------------------------------------------------------------+ diff --git a/arch/powerpc/cpu/ppc4xx/u-boot-spl.lds b/arch/powerpc/cpu/ppc4xx/u-boot-spl.lds new file mode 100644 index 0000000..4634263 --- /dev/null +++ b/arch/powerpc/cpu/ppc4xx/u-boot-spl.lds @@ -0,0 +1,74 @@ +/* + * Copyright 2012-2013 Stefan Roese <sr(a)denx.de> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +MEMORY +{ + sdram : ORIGIN = CONFIG_SPL_BSS_START_ADDR, + LENGTH = CONFIG_SPL_BSS_MAX_SIZE + flash : ORIGIN = CONFIG_SPL_TEXT_BASE, + LENGTH = CONFIG_SYS_SPL_MAX_LEN +} + +OUTPUT_ARCH(powerpc) +ENTRY(_start) +SECTIONS +{ +#ifdef CONFIG_440 + .bootpg 0xfffff000 : + { + arch/powerpc/cpu/ppc4xx/start.o (.bootpg) + + /* + * PPC440 board need a board specific object with the + * TLB definitions. This needs to get included right after + * start.o, since the first shadow TLB only covers 4k + * of address space. + */ + CONFIG_BOARDDIR/init.o (.bootpg) + } > flash +#endif + + .resetvec 0xFFFFFFFC : + { + KEEP(*(.resetvec)) + } > flash + + .text : + { + __start = .; + arch/powerpc/cpu/ppc4xx/start.o (.text) + CONFIG_BOARDDIR/init.o (.text) + *(.text*) + } > flash + + . = ALIGN(4); + .data : { *(SORT_BY_ALIGNMENT(.data*)) } > flash + + . = ALIGN(4); + .rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } > flash + + .bss : + { + . = ALIGN(4); + __bss_start = .; + *(.bss*) + . = ALIGN(4); + __bss_end__ = .; + } > sdram +} diff --git a/arch/powerpc/cpu/ppc4xx/u-boot.lds b/arch/powerpc/cpu/ppc4xx/u-boot.lds index a96ddd5..540f7ca 100644 --- a/arch/powerpc/cpu/ppc4xx/u-boot.lds +++ b/arch/powerpc/cpu/ppc4xx/u-boot.lds @@ -96,6 +96,7 @@ SECTIONS . = ALIGN(256); __init_end = .; +#ifndef CONFIG_SPL #ifdef CONFIG_440 .bootpg RESET_VECTOR_ADDRESS - 0xffc : { @@ -132,6 +133,7 @@ SECTIONS #if (RESET_VECTOR_ADDRESS == 0xfffffffc) . |= 0x10; #endif +#endif /* CONFIG_SPL */ __bss_start = .; .bss (NOLOAD) : -- 1.8.1.4

2 10