November 2013 - U-Boot

[U-Boot] [PATCH v4 0/3] ARM: tegra: Add the Tamonten-NG Evaluation carrier boards
by Alban Bedel 14 Nov '13

14 Nov '13

Hi everyone, I hope everything requiered is there this time: * The SKU ID has been changed to SKU_ID_T30MQS_P_A3 as suggested by Thierry * A new patch has been added to enable the 5th i2c bus on T30, this is now needed because: * The i2c buses have been re-numbered to match the numbering used in the kernel * The DTS has been re-worked to better reflect the split between COM and base board. For the i2c buses the split was done according to where the pull-ups are. So buses enabled in the COM dts have their pull-ups on the COM module. * All the "useless" defines have now been removed. Alban Bedel (3): ARM: tegra: support SKU b1 of Tegra30 i2c: tegra: Add the fifth bus on SoC with more than 4 buses ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board arch/arm/cpu/tegra-common/ap.c | 1 + arch/arm/include/asm/arch-tegra/tegra.h | 1 + .../common/pinmux-config-tamonten-ng.h | 385 +++++++++++++++++++++ board/avionic-design/common/tamonten-ng.c | 85 +++++ board/avionic-design/dts/tegra30-tamonten.dtsi | 69 ++++ board/avionic-design/dts/tegra30-tec-ng.dts | 18 + board/avionic-design/tec-ng/Makefile | 32 ++ boards.cfg | 1 + drivers/i2c/tegra_i2c.c | 5 + include/configs/tec-ng.h | 84 +++++ 10 files changed, 681 insertions(+) create mode 100644 board/avionic-design/common/pinmux-config-tamonten-ng.h create mode 100644 board/avionic-design/common/tamonten-ng.c create mode 100644 board/avionic-design/dts/tegra30-tamonten.dtsi create mode 100644 board/avionic-design/dts/tegra30-tec-ng.dts create mode 100644 board/avionic-design/tec-ng/Makefile create mode 100644 include/configs/tec-ng.h -- 1.8.4.2

3 7

[U-Boot] [PATCH 2/2] powerpc/t104xrdb: Add T1042RDB_PI board support
by Priyanka Jain 14 Nov '13

14 Nov '13

T1042RDB_PI is Freescale Reference Design Board supporting the T1042 QorIQ Power Architecture™ processor. T1042 is a reduced personality of T1040 SoC without Integrated 8-port Gigabit. The board is designed with low power features targeted for Printing Image Market. T1042RDB_PI is similar to T1040RDB board with few differences like it has video interface, supports T1042 personality T1042RDB_PI board Overview ----------------------- - Four e5500 cores, each with a private 256 KB L2 cache - 256 KB shared L3 CoreNet platform cache (CPC) - Interconnect CoreNet platform - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: - Packet parsing, classification, and distribution - Queue management for scheduling, packet sequencing, and congestion management - Cryptography Acceleration - RegEx Pattern Matching Acceleration - IEEE Std 1588 support - Hardware buffer management for buffer allocation and deallocation - Ethernet interfaces - Two on-board RGMII 10/100/1G ethernet ports. - SERDES Connections, 8 lanes supporting: — PCI — SATA 2.0 - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and Interleaving -IFC/Local Bus - NAND flash: 1GB 8-bit NAND flash - NOR: 128MB 16-bit NOR Flash - Ethernet - Two on-board RGMII 10/100/1G ethernet ports. - PHY #0 remains powered up during deep-sleep - CPLD - Clocks - System and DDR clock (SYSCLK, “DDRCLK”) - SERDES clocks - Video - DIU supports video at up to 1280x1024x32bpp - Power Supplies - USB - Supports two USB 2.0 ports with integrated PHYs — Two type A ports with 5V(a)1.5A per port. - SDHC - SDHC/SDXC connector - SPI - On-board 64MB SPI flash - Other IO - Two Serial ports - ProfiBus port - Four I2C ports Signed-off-by: Poonam Aggrwal <poonam.aggrwal(a)freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar(a)freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain(a)freescale.com> --- Based on u-boot-mpc85xx/next branch. board/freescale/t104xrdb/README | 38 ++ boards.cfg | 1 + include/configs/T1042RDB_PI.h | 709 +++++++++++++++++++++++++++++++++++++++ 3 files changed, 748 insertions(+), 0 deletions(-) create mode 100644 include/configs/T1042RDB_PI.h diff --git a/board/freescale/t104xrdb/README b/board/freescale/t104xrdb/README index e8848ee..2cd8219 100644 --- a/board/freescale/t104xrdb/README +++ b/board/freescale/t104xrdb/README @@ -4,6 +4,10 @@ The T1040RDB is a Freescale reference board that hosts the T1040 SoC (and variants). Variants inclued T1042 presonality of T1040, in which case T1040RDB can also be called T1042RDB. +The T1042RDB_PI is a Freescale reference board that hosts the T1042 SoC. +(a personality of T1040 SoC). The board is similar to T1040RDB but is +designed specially with low power features targeted for Printing Image Market. + T1040 SoC Overview ------------------ The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA @@ -97,6 +101,40 @@ T1040RDB board Overview - Two Serial ports - Four I2C ports +T1042RDB_PI board Overview +------------------------- + - SERDES Connections, 8 lanes information: + 1, 2, 3, 4 : PCIe x4 slot + 5: mini PCIe connector + 6: mini PCIe connector + 7: NA + 8: SATA connector + - DDR Controller + - Supports rates of up to 1600 MHz data-rate + - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types. + - IFC/Local Bus + - NAND flash: 1GB 8-bit NAND flash + - NOR: 128MB 16-bit NOR Flash + - Ethernet + - Two on-board RGMII 10/100/1G ethernet ports. + - CPLD + - Clocks + - System and DDR clock (SYSCLK, “DDRCLK”) + - SERDES clocks + - Video + - DIU supports video at up to 1280x1024x32bpp + - Power Supplies + - USB + - Supports two USB 2.0 ports with integrated PHYs + - Two type A ports with 5V(a)1.5A per port. + - SDHC + - SDHC/SDXC connector + - SPI + - On-board 64MB SPI flash + - Other IO + - Two Serial ports + - Four I2C ports + Memory map ----------- The addresses in brackets are physical addresses. diff --git a/boards.cfg b/boards.cfg index 33714fe..b040b66 100644 --- a/boards.cfg +++ b/boards.cfg @@ -959,6 +959,7 @@ Active powerpc mpc85xx - freescale t4qds Active powerpc mpc85xx - freescale t4qds T4240QDS_SRIO_PCIE_BOOT T4240QDS:PPC_T4240,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 - Active powerpc mpc85xx - freescale t1040qds T1040QDS T1040QDS:PPC_T1040 Naveen Burmi <NaveenBurmi(a)freescale.com> Active powerpc mpc85xx - freescale t104xrdb T1040RDB T1040RDB:PPC_T1040 Poonam Aggrwal <poonam.aggrwal(a)freescale.com> +Active powerpc mpc85xx - freescale t104xrdb T1042RDB_PI T1042RDB_PI:PPC_T1040 Poonam Aggrwal <poonam.aggrwal(a)freescale.com> Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD controlcenterd:36BIT,SDCARD Dirk Eibach <eibach(a)gdsys.de> Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD_DEVELOP controlcenterd:36BIT,SDCARD,DEVELOP Dirk Eibach <eibach(a)gdsys.de> Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER controlcenterd:TRAILBLAZER,SPIFLASH Dirk Eibach <eibach(a)gdsys.de> diff --git a/include/configs/T1042RDB_PI.h b/include/configs/T1042RDB_PI.h new file mode 100644 index 0000000..0d0296a --- /dev/null +++ b/include/configs/T1042RDB_PI.h @@ -0,0 +1,709 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * T1042RDB_PI board configuration file + */ +#define CONFIG_T104xRDB +#define CONFIG_T1042RDB_PI +#define CONFIG_PHYS_64BIT + +#ifdef CONFIG_RAMBOOT_PBL +#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#endif + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_E500MC /* BOOKE e500mc family */ +#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ +#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */ +#define CONFIG_MP /* support multiple processors */ + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff80000 +#endif + +#ifndef CONFIG_RESET_VECTOR_ADDRESS +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc +#endif + +#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ +#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS +#define CONFIG_FSL_IFC /* Enable IFC Support */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_PCIE2 /* PCIE controler 2 */ +#define CONFIG_PCIE3 /* PCIE controler 3 */ +#define CONFIG_PCIE4 /* PCIE controler 4 */ + +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +#define CONFIG_ENV_OVERWRITE + +#ifdef CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_NOWHERE +#else +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#endif + +#ifndef CONFIG_SYS_NO_FLASH +#if defined(CONFIG_SPIFLASH) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ +#define CONFIG_ENV_SECT_SIZE 0x10000 +#elif defined(CONFIG_SDCARD) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_OFFSET (512 * 1105) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif +#else /* CONFIG_SYS_NO_FLASH */ +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif + +#define CONFIG_SYS_CLK_FREQ 100000000 +#define CONFIG_DDR_CLK_FREQ 66666666 + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_SYS_CACHE_STASHING +#define CONFIG_BACKSIDE_L2_CACHE +#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_DDR_ECC +#ifdef CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#endif + +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ + +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* + * Config the L3 Cache as L3 SRAM + */ +#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 + +#define CONFIG_SYS_DCSRBAR 0xf0000000 +#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull + +/* + * DDR Setup + */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */ +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) + +#define CONFIG_DDR_SPD +#define CONFIG_SYS_DDR_RAW_TIMING +#define CONFIG_FSL_DDR3 + +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x51 + +#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ + +/* + * IFC Definitions + */ +#define CONFIG_SYS_FLASH_BASE 0xe8000000 +#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) + +#define CONFIG_SYS_NOR_CSPR_EXT (0xf) +#define CONFIG_SYS_NOR_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) +/* NOR Flash Timing Params */ +#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ + FTIM0_NOR_TEADC(0x5) | \ + FTIM0_NOR_TEAHC(0x5)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ + FTIM1_NOR_TRAD_NOR(0x1A) |\ + FTIM1_NOR_TSEQRAD_NOR(0x13)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ + FTIM2_NOR_TCH(0x4) | \ + FTIM2_NOR_TWPH(0x0E) | \ + FTIM2_NOR_TWP(0x1c)) +#define CONFIG_SYS_NOR_FTIM3 0x0 + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} + +/* CPLD on IFC */ +#define CONFIG_SYS_CPLD_BASE 0xffdf0000 +#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) +#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_GPCM \ + | CSPR_V) +#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) +#define CONFIG_SYS_CSOR2 0x0 +/* CPLD Timing parameters for IFC CS2 */ +#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ + FTIM0_GPCM_TEADC(0x0e) | \ + FTIM0_GPCM_TEAHC(0x0e)) +#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ + FTIM1_GPCM_TRAD(0x1f)) +#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ + FTIM2_GPCM_TCH(0x0) | \ + FTIM2_GPCM_TWP(0x1f)) +#define CONFIG_SYS_CS2_FTIM3 0x0 + +/* NAND Flash on IFC */ +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_BASE 0xff800000 +#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) + +#define CONFIG_SYS_NAND_CSPR_EXT (0xf) +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ + | CSPR_MSEL_NAND /* MSEL = NAND */ \ + | CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) + +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ + | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ + | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ + | CSOR_NAND_SPRZ_224/* Spare size = 224 */ \ + | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +/* ONFI NAND Flash mode0 Timing Params */ +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ + FTIM0_NAND_TWP(0x18) | \ + FTIM0_NAND_TWCHT(0x07) | \ + FTIM0_NAND_TWH(0x0a)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ + FTIM1_NAND_TWBE(0x39) | \ + FTIM1_NAND_TRR(0x0e) | \ + FTIM1_NAND_TRP(0x18)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ + FTIM2_NAND_TREH(0x0a) | \ + FTIM2_NAND_TWHRE(0x1e)) +#define CONFIG_SYS_NAND_FTIM3 0x0 + +#define CONFIG_SYS_NAND_DDR_LAW 11 +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND + +#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) + +#if defined(CONFIG_NAND) +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 +#else +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 +#endif + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#if defined(CONFIG_RAMBOOT_PBL) +#define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_MISC_INIT_R + +#define CONFIG_HWCONFIG + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) +#define CONFIG_SERIAL_MULTI /* Enable both serial ports */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ +#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000 + +/* I2C bus multiplexer */ +#define I2C_MUX_PCA_ADDR 0x70 + +/* + * RTC configuration + */ +#define RTC +#define CONFIG_RTC_DS1337 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 + +/*DVI encoder*/ +#define CONFIG_HDMI_ENCODER_I2C_ADDR 0x75 + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_FSL_ESPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE 0 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +#ifdef CONFIG_PCI +/* controller 1, direct to uli, tgtid 3, Base address 20000 */ +#ifdef CONFIG_PCIE1 +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 2, Slot 2, tgtid 2, Base address 201000 */ +#ifdef CONFIG_PCIE2 +#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 3, Slot 1, tgtid 1, Base address 202000 */ +#ifdef CONFIG_PCIE3 +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 4, Base address 203000 */ +#ifdef CONFIG_PCIE4 +#define CONFIG_SYS_PCIE4_MEM_VIRT 0xb0000000 +#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc30000000ull +#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE4_IO_VIRT 0xf8030000 +#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull +#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ +#endif + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_E1000 + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif /* CONFIG_PCI */ + +/* SATA */ +#define CONFIG_FSL_SATA_V2 +#ifdef CONFIG_FSL_SATA_V2 +#define CONFIG_LIBATA +#define CONFIG_FSL_SATA + +#define CONFIG_SYS_SATA_MAX_DEVICE 1 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA + +#define CONFIG_LBA48 +#define CONFIG_CMD_SATA +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +#endif + +/* +* USB +*/ +#define CONFIG_HAS_FSL_DR_USB + +#ifdef CONFIG_HAS_FSL_DR_USB +#define CONFIG_USB_EHCI + +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_CMD_EXT2 +#endif +#endif + +#define CONFIG_MMC + +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* Qman/Bman */ +#ifndef CONFIG_NOBQFMAN +#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ +#define CONFIG_SYS_BMAN_NUM_PORTALS 25 +#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 +#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull +#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 +#define CONFIG_SYS_QMAN_NUM_PORTALS 25 +#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 +#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull +#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 + +#define CONFIG_SYS_DPAA_FMAN +#define CONFIG_SYS_DPAA_PME + +/* Default address of microcode for the Linux Fman driver */ +#if defined(CONFIG_SPIFLASH) +/* + * env is stored at 0x100000, sector size is 0x10000, ucode is stored after + * env, so we got 0x110000. + */ +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000 +#elif defined(CONFIG_SDCARD) +/* + * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is + * about 545KB (1089 blocks), Env is stored after the image, and the env size is + * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_MMC +#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_QE_FMAN_FW_IN_NAND +#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000 +#endif +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) +#endif /* CONFIG_NOBQFMAN */ + +#ifdef CONFIG_SYS_DPAA_FMAN +#define CONFIG_FMAN_ENET +#define CONFIG_PHYLIB_10G +#define CONFIG_PHY_VITESSE +#define CONFIG_PHY_REALTEK +#define CONFIG_PHY_TERANETICS +#define SGMII_CARD_PORT1_PHY_ADDR 0x1C +#define SGMII_CARD_PORT2_PHY_ADDR 0x10 +#define SGMII_CARD_PORT3_PHY_ADDR 0x1E +#define SGMII_CARD_PORT4_PHY_ADDR 0x11 +#endif + +#ifdef CONFIG_FMAN_ENET +#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x10 +#define CONFIG_SYS_FM1_DTSEC6_PHY_ADDR 0x11 +#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 4 + +#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c +#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d +#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e +#define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC1" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* + * Environment + */ +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ERRATA +#define CONFIG_CMD_GREPENV +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SETEXPR + +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /*-1 disables auto-boot*/ + +#define CONFIG_BAUDRATE 115200 + +#define __USB_PHY_TYPE utmi + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ + "bank_intlv=cs0_cs1;" \ + "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ + "netdev=eth0\0" \ + "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ + "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot && " \ + "protect off $ubootaddr +$filesize && " \ + "erase $ubootaddr +$filesize && " \ + "cp.b $loadaddr $ubootaddr $filesize && " \ + "protect on $ubootaddr +$filesize && " \ + "cmp.b $loadaddr $ubootaddr $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=t1040rdb_pi/ramdisk.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=t1040rdb_pi/t1040rdb_pi.dtb\0" \ + "bdev=sda3\0" \ + "c=ffe\0" + +#define CONFIG_LINUX \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "setenv ramdiskaddr 0x02000000;" \ + "setenv fdtaddr 0x00c00000;" \ + "setenv loadaddr 0x1000000;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_HDBOOT \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_LINUX + +#ifdef CONFIG_SECURE_BOOT +#include <asm/fsl_secure_boot.h> +#endif + +#endif /* __CONFIG_H */ -- 1.7.4.1

2 1

Re: [U-Boot] [U-Boot, v1, 1/4] mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
by Gupta, Pekon 14 Nov '13

14 Nov '13

> From: Scott Wood [mailto:scottwood@freescale.com] > On Tue, Sep 10, 2013 at 06:57:05PM +0530, pekon gupta wrote: > > From: Matthieu CASTET <matthieu.castet(a)parrot.com> > > > > This patch is slightly modified from following linux patch > > http://lists.infradead.org/pipermail/linux-mtd/2012- > November/044803.html > > Which is now commit 64b37b2a63eb2f80b65c7185f0013f8ffc637ae3 > > > So retaining the authorship to Matthieu CASTET > <matthieu.castet(a)parrot.com> > > *Modifications from original patch* > > reset chip->read_byte, chip->read_buf, chip->write_buf before setting > defaults. > > Why does U-Boot need this if Linux doesn't? > Yes, I plan to drop this patch. Reason: Though this feature was introduced in linux long back, but hardly any mtd/nand drivers using this. Also there are alternative approaches which do not require any change in individual controller drivers, but just in generic NAND driver. I have proposed them in linux mtd-maillist, I'll propose same in my next version of patch-set. http://lists.infradead.org/pipermail/linux-mtd/2013-November/049744.html with regards, pekon

2 1

[U-Boot] [PATCH 00/14] ARM: AM43xx: Update support for AM4372 SoC
by Lokesh Vutla 14 Nov '13

14 Nov '13

This Patch series updates support for AM4372 EPOS and GP EVM boards. AM4372 is a low cost Cortex-A9 based application processor targeted at existing ARM9/ARM11 base of customers that need more processing capabilities. Currently there are two boards with AM4372 SoC: EPOS and GP EVM. Except for few differences like oscillator clock and SDRAM both EPOS and GP EVM boards are similar. EPOS EVM: OSC clk : 25MHz DDR : LPDDR2 @ 266MHz (MT42L256M32D2LG-25 WT:A) GP EVM: OSC clk : 24MHz DDR : DDR3 @ 400MHz(MT47H128M16RT-187E:C) This patch series is applied on top of Mainline U-Boot Tree and two patches mentioned below: git://git.denx.de/u-boot.git master http://patchwork.ozlabs.org/patch/288175/ http://patchwork.ozlabs.org/patch/279755/ Testing: -> Boot tested on AM4372 EPOS and GP EVMs, Beaglebone Black. -> verified MAKEALL -s am33xx. -> Ran checkpatch on all patches. Lokesh Vutla (12): ARM: AM43xx: Update the base addresses of modules ARM: AM43xx: Adapt to ti_armv7_common.h config file ARM: AM43xx: Add L2 Support ARM: AM43xx: Add extra ENV settings ARM: AM43xx: Select clk source for Timer2 ARM: AM43xx: Update Current Booting devices list ARM: AM43xx: mux: Update mux data ARM: AM43xx: clocks: Update DPLL details for EPOS EVM ARM: AM43xx: clocks: Add DPLL data for GP EVM ARM: AM43xx: EPOS_EVM: Add support for LPDDR2 ARM: AM43xx: GP_EVM: Add support for DDR3 ARM: AM43xx: Add Maintainer Sekhar Nori (2): ARM: AM43XX: board: add support for reading onboard EEPROM ARM: AM43XX: Add CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG support arch/arm/cpu/armv7/am33xx/Makefile | 8 +- arch/arm/cpu/armv7/am33xx/clock.c | 12 +- arch/arm/cpu/armv7/am33xx/clock_am33xx.c | 15 ++ arch/arm/cpu/armv7/am33xx/clock_am43xx.c | 12 +- arch/arm/cpu/armv7/am33xx/emif4d5.c | 185 ++++++++++++++ arch/arm/include/asm/arch-am33xx/clock.h | 7 +- arch/arm/include/asm/arch-am33xx/clocks_am33xx.h | 3 + arch/arm/include/asm/arch-am33xx/cpu.h | 22 +- arch/arm/include/asm/arch-am33xx/ddr_defs.h | 34 +++ arch/arm/include/asm/arch-am33xx/hardware.h | 8 - arch/arm/include/asm/arch-am33xx/hardware_am33xx.h | 3 + arch/arm/include/asm/arch-am33xx/hardware_am43xx.h | 4 + arch/arm/include/asm/arch-am33xx/hardware_ti814x.h | 3 + arch/arm/include/asm/arch-am33xx/hardware_ti816x.h | 3 + arch/arm/include/asm/arch-am33xx/mux_am43xx.h | 4 +- arch/arm/include/asm/arch-am33xx/omap.h | 2 + arch/arm/include/asm/arch-am33xx/spl.h | 12 +- arch/arm/include/asm/emif.h | 12 + board/ti/am43xx/board.c | 263 +++++++++++++++++++- board/ti/am43xx/board.h | 33 +++ board/ti/am43xx/mux.c | 29 ++- boards.cfg | 2 +- include/configs/am43xx_evm.h | 205 ++++++++------- 23 files changed, 737 insertions(+), 144 deletions(-) create mode 100644 arch/arm/cpu/armv7/am33xx/emif4d5.c -- 1.7.9.5

4 49

[U-Boot] [PATCH][RESEND 0/2] get_ram_size incorrectly returns long, should be unsigned long
by Oliver Schinagl 14 Nov '13

14 Nov '13

1 2

[U-Boot] [PATCH 4/4] t2080qds/ramboot: enable PBL tool for t2080qds
by Shengzhou Liu 14 Nov '13

14 Nov '13

Add the default RCW(0x66_0x16) and PBI configure file for T2080QDS board, so we can use PBL tool to generate the ramboot image to support boot from NAND/SPI/SD. Signed-off-by: Shengzhou Liu <Shengzhou.Liu(a)freescale.com> --- Against master branch of upstream. board/freescale/t2080qds/t2080_pbi.cfg | 41 ++++++++++++++++++++++++++++++++++ board/freescale/t2080qds/t2080_rcw.cfg | 8 +++++++ 2 files changed, 49 insertions(+) create mode 100644 board/freescale/t2080qds/t2080_pbi.cfg create mode 100644 board/freescale/t2080qds/t2080_rcw.cfg diff --git a/board/freescale/t2080qds/t2080_pbi.cfg b/board/freescale/t2080qds/t2080_pbi.cfg new file mode 100644 index 0000000..e200d92 --- /dev/null +++ b/board/freescale/t2080qds/t2080_pbi.cfg @@ -0,0 +1,41 @@ +# +# Copyright 2013 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Refer doc/README.pblimage for more details about how-to configure +# and create PBL boot image +# + +#PBI commands +#Initialize CPC1 +09010000 00200400 +09138000 00000000 +091380c0 00000100 +#512KB SRAM +09010100 00000000 +09010104 fff80009 +09010f00 08000000 +#enable CPC1 +09010000 80000000 +#Configure LAW for CPC1 +09000d00 00000000 +09000d04 fff80000 +09000d08 81000012 +#Initialize eSPI controller, default configuration is slow for eSPI to +#load data, this configuration comes from u-boot eSPI driver. +09110000 80000403 +09110020 2d170008 +09110024 00100008 +09110028 00100008 +0911002c 00100008 +#Errata for slowing down the MDC clock to make it <= 2.5 MHZ +094fc030 00008148 +094fd030 00008148 +#Configure alternate space +09000010 00000000 +09000014 ff000000 +09000018 81000000 +#Flush PBL data +09138000 00000000 +091380c0 00000000 diff --git a/board/freescale/t2080qds/t2080_rcw.cfg b/board/freescale/t2080qds/t2080_rcw.cfg new file mode 100644 index 0000000..c2ad0fd --- /dev/null +++ b/board/freescale/t2080qds/t2080_rcw.cfg @@ -0,0 +1,8 @@ +#PBL preamble and RCW header +aa55aa55 010e0100 +#SerDes Protocol: 0x66_0x16 +#Core/DDR: 1533Mhz/2133MT/s +12100017 15000000 00000000 00000000 +66160002 00008400 e8104000 c1000000 +00000000 00000000 00000000 000307fc +00000000 00000000 00000000 00000004 -- 1.8.0

1 0

[U-Boot] [PATCH 2/4] powerpc/mpc85xx: Add T2080/T2081 SoC support
by Shengzhou Liu 14 Nov '13

14 Nov '13

Add support for Freescale T2080/T2081 SoC. T2080 includes the following functions and features: - Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz - 2MB L2 cache and 512KB CoreNet platform cache (CPC) - Hierarchical interconnect fabric - One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving - Data Path Acceleration Architecture (DPAA) incorporating acceleration - 16 SerDes lanes up to 10.3125 GHz - 8 mEMACs for network interfaces (four 1Gbps MACs and four 10Gbps/1Gbps MACs) - High-speed peripheral interfaces - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV) - Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz - Additional peripheral interfaces - Two serial ATA (SATA 2.0) controllers - Two high-speed USB 2.0 controllers with integrated PHY - Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC) - Enhanced serial peripheral interface (eSPI) - Four I2C controllers - Four 2-pin UARTs or two 4-pin UARTs - Integrated Flash Controller supporting NAND and NOR flash - Three eight-channel DMA engines - Support for hardware virtualization and partitioning enforcement - QorIQ Platform's Trust Architecture 2.0 Differences between T2080 and T2081: Feature T2080 T2081 1G Ethernet numbers: 8 6 10G Ethernet numbers: 4 2 SerDes lanes: 16 8 Serial RapidIO,RMan: 2 no SATA Controller: 2 no Aurora: yes no SoC Package: 896-pins 780-pins Signed-off-by: Shengzhou Liu <Shengzhou.Liu(a)freescale.com> --- Against master branch of upstream. arch/powerpc/cpu/mpc85xx/Makefile | 6 + arch/powerpc/cpu/mpc85xx/speed.c | 2 +- arch/powerpc/cpu/mpc85xx/t2080_ids.c | 142 ++++++++++++++++++++ arch/powerpc/cpu/mpc85xx/t2080_serdes.c | 209 ++++++++++++++++++++++++++++++ arch/powerpc/cpu/mpc8xxx/cpu.c | 2 + arch/powerpc/include/asm/config_mpc85xx.h | 43 ++++++ arch/powerpc/include/asm/immap_85xx.h | 16 +++ arch/powerpc/include/asm/processor.h | 2 + drivers/net/fm/Makefile | 2 + drivers/net/fm/t2080.c | 92 +++++++++++++ 10 files changed, 515 insertions(+), 1 deletion(-) create mode 100644 arch/powerpc/cpu/mpc85xx/t2080_ids.c create mode 100644 arch/powerpc/cpu/mpc85xx/t2080_serdes.c create mode 100644 drivers/net/fm/t2080.c diff --git a/arch/powerpc/cpu/mpc85xx/Makefile b/arch/powerpc/cpu/mpc85xx/Makefile index 50ddb50..22b98db 100644 --- a/arch/powerpc/cpu/mpc85xx/Makefile +++ b/arch/powerpc/cpu/mpc85xx/Makefile @@ -70,6 +70,8 @@ obj-$(CONFIG_PPC_B4860) += ddr-gen3.o obj-$(CONFIG_BSC9131) += ddr-gen3.o obj-$(CONFIG_BSC9132) += ddr-gen3.o obj-$(CONFIG_PPC_T1040) += ddr-gen3.o +obj-$(CONFIG_PPC_T2080) += ddr-gen3.o +obj-$(CONFIG_PPC_T2081) += ddr-gen3.o obj-$(CONFIG_CPM2) += ether_fcc.o obj-$(CONFIG_OF_LIBFDT) += fdt.o @@ -89,6 +91,8 @@ obj-$(CONFIG_PPC_T4160) += t4240_ids.o obj-$(CONFIG_PPC_B4420) += b4860_ids.o obj-$(CONFIG_PPC_B4860) += b4860_ids.o obj-$(CONFIG_PPC_T1040) += t1040_ids.o +obj-$(CONFIG_PPC_T2080) += t2080_ids.o +obj-$(CONFIG_PPC_T2081) += t2080_ids.o obj-$(CONFIG_QE) += qe_io.o obj-$(CONFIG_CPM2) += serial_scc.o @@ -128,6 +132,8 @@ obj-$(CONFIG_PPC_B4420) += b4860_serdes.o obj-$(CONFIG_PPC_B4860) += b4860_serdes.o obj-$(CONFIG_BSC9132) += bsc9132_serdes.o obj-$(CONFIG_PPC_T1040) += t1040_serdes.o +obj-$(CONFIG_PPC_T2080) += t2080_serdes.o +obj-$(CONFIG_PPC_T2081) += t2080_serdes.o obj-y += cpu.o obj-y += cpu_init.o diff --git a/arch/powerpc/cpu/mpc85xx/speed.c b/arch/powerpc/cpu/mpc85xx/speed.c index d08a8d2..1a58a19 100644 --- a/arch/powerpc/cpu/mpc85xx/speed.c +++ b/arch/powerpc/cpu/mpc85xx/speed.c @@ -122,7 +122,7 @@ void get_sys_info(sys_info_t *sys_info) sys_info->freq_processor[cpu] = freq_c_pll[cplx_pll] / core_cplx_pll_div[c_pll_sel]; } -#ifdef CONFIG_PPC_B4860 +#if defined(CONFIG_PPC_B4860) || defined(CONFIG_PPC_T2080) #define FM1_CLK_SEL 0xe0000000 #define FM1_CLK_SHIFT 29 #else diff --git a/arch/powerpc/cpu/mpc85xx/t2080_ids.c b/arch/powerpc/cpu/mpc85xx/t2080_ids.c new file mode 100644 index 0000000..068e1f2 --- /dev/null +++ b/arch/powerpc/cpu/mpc85xx/t2080_ids.c @@ -0,0 +1,142 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> + +#ifdef CONFIG_SYS_DPAA_QBMAN +struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = { + /* dqrr liodn, frame data liodn, liodn off, sdest */ + SET_QP_INFO(1, 27, 1, 0), + SET_QP_INFO(2, 28, 1, 0), + SET_QP_INFO(3, 29, 1, 1), + SET_QP_INFO(4, 30, 1, 1), + SET_QP_INFO(5, 31, 1, 2), + SET_QP_INFO(6, 32, 1, 2), + SET_QP_INFO(7, 33, 1, 3), + SET_QP_INFO(8, 34, 1, 3), + SET_QP_INFO(9, 35, 1, 0), + SET_QP_INFO(10, 36, 1, 0), + SET_QP_INFO(11, 37, 1, 1), + SET_QP_INFO(12, 38, 1, 1), + SET_QP_INFO(13, 39, 1, 2), + SET_QP_INFO(14, 40, 1, 2), + SET_QP_INFO(15, 41, 1, 3), + SET_QP_INFO(16, 42, 1, 3), + SET_QP_INFO(17, 43, 1, 0), + SET_QP_INFO(18, 44, 1, 0), +}; +#endif + +#ifdef CONFIG_SYS_SRIO +struct srio_liodn_id_table srio_liodn_tbl[] = { + SET_SRIO_LIODN_BASE(1, 307), + SET_SRIO_LIODN_BASE(2, 387), +}; +int srio_liodn_tbl_sz = ARRAY_SIZE(srio_liodn_tbl); +#endif + +struct liodn_id_table liodn_tbl[] = { +#ifdef CONFIG_SYS_DPAA_QBMAN + SET_QMAN_LIODN(62), + SET_BMAN_LIODN(63), +#endif + + SET_SDHC_LIODN(1, 552), + + SET_PME_LIODN(117), + + SET_USB_LIODN(1, "fsl-usb2-mph", 553), + SET_USB_LIODN(2, "fsl-usb2-dr", 554), + + SET_SATA_LIODN(1, 555), + SET_SATA_LIODN(2, 556), + + SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 1, 148), + SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 228), + SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 308), + SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 388), + + SET_DMA_LIODN(1, 147), + SET_DMA_LIODN(2, 227), + SET_DMA_LIODN(3, 226), + + SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0), + SET_GUTS_LIODN(NULL, 200, rio2liodnr, 0), + SET_GUTS_LIODN(NULL, 201, rio1maintliodnr, 0), + SET_GUTS_LIODN(NULL, 202, rio2maintliodnr, 0), + +#ifdef CONFIG_SYS_PMAN + SET_PMAN_LIODN(1, 513), + SET_PMAN_LIODN(2, 514), + SET_PMAN_LIODN(3, 515), +#endif + + /* SET_NEXUS_LIODN(557), -- not yet implemented */ +}; +int liodn_tbl_sz = ARRAY_SIZE(liodn_tbl); + +#ifdef CONFIG_SYS_DPAA_FMAN +struct liodn_id_table fman1_liodn_tbl[] = { + SET_FMAN_RX_1G_LIODN(1, 0, 88), + SET_FMAN_RX_1G_LIODN(1, 1, 89), + SET_FMAN_RX_1G_LIODN(1, 2, 90), + SET_FMAN_RX_1G_LIODN(1, 3, 91), + SET_FMAN_RX_1G_LIODN(1, 4, 92), + SET_FMAN_RX_1G_LIODN(1, 5, 93), + SET_FMAN_RX_10G_LIODN(1, 0, 94), + SET_FMAN_RX_10G_LIODN(1, 1, 95), +}; +int fman1_liodn_tbl_sz = ARRAY_SIZE(fman1_liodn_tbl); +#endif + +struct liodn_id_table sec_liodn_tbl[] = { + SET_SEC_JR_LIODN_ENTRY(0, 454, 458), + SET_SEC_JR_LIODN_ENTRY(1, 455, 459), + SET_SEC_JR_LIODN_ENTRY(2, 456, 460), + SET_SEC_JR_LIODN_ENTRY(3, 457, 461), + SET_SEC_RTIC_LIODN_ENTRY(a, 453), + SET_SEC_RTIC_LIODN_ENTRY(b, 549), + SET_SEC_RTIC_LIODN_ENTRY(c, 550), + SET_SEC_RTIC_LIODN_ENTRY(d, 551), + SET_SEC_DECO_LIODN_ENTRY(0, 541, 610), + SET_SEC_DECO_LIODN_ENTRY(1, 542, 611), + SET_SEC_DECO_LIODN_ENTRY(2, 543, 612), + SET_SEC_DECO_LIODN_ENTRY(3, 544, 613), + SET_SEC_DECO_LIODN_ENTRY(4, 545, 614), + SET_SEC_DECO_LIODN_ENTRY(5, 546, 615), + SET_SEC_DECO_LIODN_ENTRY(6, 547, 616), + SET_SEC_DECO_LIODN_ENTRY(7, 548, 617), +}; +int sec_liodn_tbl_sz = ARRAY_SIZE(sec_liodn_tbl); + +#ifdef CONFIG_SYS_DPAA_RMAN +struct liodn_id_table rman_liodn_tbl[] = { + /* Set RMan block 0-3 liodn offset */ + SET_RMAN_LIODN(0, 6), + SET_RMAN_LIODN(1, 7), + SET_RMAN_LIODN(2, 8), + SET_RMAN_LIODN(3, 9), +}; +int rman_liodn_tbl_sz = ARRAY_SIZE(rman_liodn_tbl); +#endif + +struct liodn_id_table liodn_bases[] = { +#ifdef CONFIG_SYS_DPAA_DCE + [FSL_HW_PORTAL_DCE] = SET_LIODN_BASE_2(618, 694), +#endif + [FSL_HW_PORTAL_SEC] = SET_LIODN_BASE_2(462, 558), +#ifdef CONFIG_SYS_DPAA_FMAN + [FSL_HW_PORTAL_FMAN1] = SET_LIODN_BASE_1(973), +#endif +#ifdef CONFIG_SYS_DPAA_PME + [FSL_HW_PORTAL_PME] = SET_LIODN_BASE_2(770, 846), +#endif +#ifdef CONFIG_SYS_DPAA_RMAN + [FSL_HW_PORTAL_RMAN] = SET_LIODN_BASE_1(922), +#endif +}; diff --git a/arch/powerpc/cpu/mpc85xx/t2080_serdes.c b/arch/powerpc/cpu/mpc85xx/t2080_serdes.c new file mode 100644 index 0000000..765b7cf --- /dev/null +++ b/arch/powerpc/cpu/mpc85xx/t2080_serdes.c @@ -0,0 +1,209 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * Shengzhou Liu <Shengzhou.Liu(a)freescale.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_serdes.h> +#include <asm/processor.h> +#include <asm/io.h> +#include "fsl_corenet2_serdes.h" + +struct serdes_config { + u32 protocol; + u8 lanes[SRDS_MAX_LANES]; +}; + +static const struct serdes_config serdes1_cfg_tbl[] = { + /* SerDes 1 */ + {0x6E, {XFI_FM1_MAC9, XFI_FM1_MAC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + PCIE4, PCIE4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0xBC, {PCIE3, PCIE3, SGMII_FM1_DTSEC1, + SGMII_FM1_DTSEC2, PCIE4, PCIE4, PCIE4, PCIE4} }, + {0xC8, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1, + SGMII_FM1_DTSEC2, PCIE4, PCIE4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0xD6, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1, + SGMII_FM1_DTSEC2, PCIE4, PCIE4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0xDE, {PCIE3, PCIE3, PCIE3, PCIE3, + PCIE4, PCIE1, PCIE2, SGMII_FM1_DTSEC6} }, + {0xE0, {PCIE3, PCIE3, PCIE3, PCIE3, PCIE4, + PCIE1, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0xF2, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1, + SGMII_FM1_DTSEC2, PCIE4, PCIE1, PCIE2, SGMII_FM1_DTSEC6} }, + {0xF8, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1, + SGMII_FM1_DTSEC2, PCIE4, PCIE1, PCIE2, SGMII_FM1_DTSEC6} }, + {0xFA, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1, + SGMII_FM1_DTSEC2, PCIE4, PCIE1, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x6C, {XFI_FM1_MAC9, XFI_FM1_MAC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + PCIE4, PCIE4, PCIE4, PCIE4} }, +#if defined(CONFIG_PPC_T2080) + {0x1C, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x95, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0xA2, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x94, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x51, {XAUI_FM1_MAC9, XAUI_FM1_MAC9, + XAUI_FM1_MAC9, XAUI_FM1_MAC9, + PCIE4, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x5F, {HIGIG_FM1_MAC9, HIGIG_FM1_MAC9, + HIGIG_FM1_MAC9, HIGIG_FM1_MAC9, + PCIE4, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x65, {HIGIG_FM1_MAC9, HIGIG_FM1_MAC9, + HIGIG_FM1_MAC9, HIGIG_FM1_MAC9, + PCIE4, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x6B, {XFI_FM1_MAC9, XFI_FM1_MAC10, + XFI_FM1_MAC1, XFI_FM1_MAC2, + PCIE4, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x6D, {XFI_FM1_MAC9, XFI_FM1_MAC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + PCIE4, PCIE4, PCIE4, PCIE4} }, + {0x71, {XFI_FM1_MAC9, XFI_FM1_MAC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, PCIE4, + SGMII_FM1_DTSEC4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0xA6, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, PCIE4, + PCIE4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x8E, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, PCIE4, + PCIE4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x8F, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, PCIE4, + PCIE4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x82, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + PCIE4, PCIE4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x83, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + PCIE4, PCIE4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0xA4, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + PCIE4, PCIE4, PCIE4, PCIE4} }, + {0x96, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + PCIE4, PCIE4, PCIE4, PCIE4} }, + {0x8A, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, + SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + PCIE4, PCIE4, PCIE4, PCIE4} }, + {0x67, {XFI_FM1_MAC9, XFI_FM1_MAC10, + XFI_FM1_MAC1, XFI_FM1_MAC2, + PCIE4, PCIE4, PCIE4, PCIE4} }, + {0xAB, {PCIE3, PCIE3, PCIE3, PCIE3, + PCIE4, PCIE4, PCIE4, PCIE4} }, + {0xDA, {PCIE3, PCIE3, PCIE3, PCIE3, + PCIE3, PCIE3, PCIE3, PCIE3} }, + {0xD9, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1, + SGMII_FM1_DTSEC2, PCIE4, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0xD3, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1, + SGMII_FM1_DTSEC2, PCIE4, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0xCB, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1, + SGMII_FM1_DTSEC2, PCIE4, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0xD8, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1, + SGMII_FM1_DTSEC2, PCIE4, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x66, {XFI_FM1_MAC9, XFI_FM1_MAC10, + XFI_FM1_MAC1, XFI_FM1_MAC2, + PCIE4, PCIE4, PCIE4, PCIE4} }, + +#elif defined(CONFIG_PPC_T2081) + {0xAA, {PCIE3, PCIE3, PCIE3, PCIE3, + PCIE4, PCIE4, PCIE4, PCIE4} }, + {0xCA, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1, + SGMII_FM1_DTSEC2, PCIE4, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, + {0x70, {XFI_FM1_MAC9, XFI_FM1_MAC10, SGMII_FM1_DTSEC1, + SGMII_FM1_DTSEC2, PCIE4, SGMII_FM1_DTSEC4, + SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} }, +#endif + {} +}; + +#ifndef CONFIG_PPC_T2081 +static const struct serdes_config serdes2_cfg_tbl[] = { + /* SerDes 2 */ + {0x1F, {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, PCIE2, PCIE2} }, + {0x16, {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, SATA1, SATA2} }, + {0x01, {PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1} }, + {0x29, {SRIO2, SRIO2, SRIO2, SRIO2, SRIO1, SRIO1, SRIO1, SRIO1} }, + {0x2D, {SRIO2, SRIO2, SRIO2, SRIO2, SRIO1, SRIO1, SRIO1, SRIO1} }, + {0x15, {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, SATA1, SATA2} }, + {0x18, {PCIE1, PCIE1, PCIE1, PCIE1, AURORA, AURORA, SATA1, SATA2} }, + {0x02, {PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1} }, + {0x36, {SRIO2, SRIO2, SRIO2, SRIO2, AURORA, AURORA, SATA1, SATA2} }, + {} +}; +#endif + +static const struct serdes_config *serdes_cfg_tbl[] = { + serdes1_cfg_tbl, +#ifndef CONFIG_PPC_T2081 + serdes2_cfg_tbl, +#endif +}; + +enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane) +{ + const struct serdes_config *ptr; + + if (serdes >= ARRAY_SIZE(serdes_cfg_tbl)) + return 0; + + ptr = serdes_cfg_tbl[serdes]; + while (ptr->protocol) { + if (ptr->protocol == cfg) + return ptr->lanes[lane]; + ptr++; + } + return 0; +} + +int is_serdes_prtcl_valid(int serdes, u32 prtcl) +{ + int i; + const struct serdes_config *ptr; + + if (serdes >= ARRAY_SIZE(serdes_cfg_tbl)) + return 0; + + ptr = serdes_cfg_tbl[serdes]; + while (ptr->protocol) { + if (ptr->protocol == prtcl) + break; + ptr++; + } + + if (!ptr->protocol) + return 0; + + for (i = 0; i < SRDS_MAX_LANES; i++) { + if (ptr->lanes[i] != NONE) + return 1; + } + + return 0; +} diff --git a/arch/powerpc/cpu/mpc8xxx/cpu.c b/arch/powerpc/cpu/mpc8xxx/cpu.c index c67be4e..35795c4 100644 --- a/arch/powerpc/cpu/mpc8xxx/cpu.c +++ b/arch/powerpc/cpu/mpc8xxx/cpu.c @@ -75,6 +75,8 @@ static struct cpu_type cpu_type_list[] = { CPU_TYPE_ENTRY(T1020, T1020, 0), CPU_TYPE_ENTRY(T1021, T1021, 0), CPU_TYPE_ENTRY(T1022, T1022, 0), + CPU_TYPE_ENTRY(T2080, T2080, 0), + CPU_TYPE_ENTRY(T2081, T2081, 0), CPU_TYPE_ENTRY(BSC9130, 9130, 1), CPU_TYPE_ENTRY(BSC9131, 9131, 1), CPU_TYPE_ENTRY(BSC9132, 9132, 2), diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h index 4cc12ee..8400f71 100644 --- a/arch/powerpc/include/asm/config_mpc85xx.h +++ b/arch/powerpc/include/asm/config_mpc85xx.h @@ -710,6 +710,49 @@ #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY #define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 +#elif defined(CONFIG_PPC_T2080) || defined(CONFIG_PPC_T2081) +#define CONFIG_E6500 +#define CONFIG_SYS_PPC64 /* 64-bit core */ +#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */ +#define CONFIG_SYS_FSL_QORIQ_CHASSIS2 /* Freescale Chassis generation 2 */ +#define CONFIG_SYS_FSL_CORES_PER_CLUSTER 4 +#define CONFIG_SYS_FSL_QMAN_V3 +#define CONFIG_MAX_CPUS 4 +#define CONFIG_SYS_FSL_NUM_LAWS 32 +#define CONFIG_SYS_FSL_SEC_COMPAT 4 +#define CONFIG_SYS_NUM_FMAN 1 +#define CONFIG_SYS_FSL_CLUSTER_CLOCKS { 2 } +#define CONFIG_SYS_FSL_SRDS_1 +#define CONFIG_SYS_FSL_PCI_VER_3_X +#if defined(CONFIG_PPC_T2080) +#define CONFIG_SYS_NUM_FM1_DTSEC 8 +#define CONFIG_SYS_NUM_FM1_10GEC 4 +#define CONFIG_SYS_FSL_SRDS_2 +#define CONFIG_SYS_FSL_SRIO_LIODN +#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 +#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 +#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 +#elif defined(CONFIG_PPC_T2081) +#define CONFIG_SYS_NUM_FM1_DTSEC 6 +#define CONFIG_SYS_NUM_FM1_10GEC 2 +#endif +#define CONFIG_SYS_FSL_NUM_USB_CTRLS 2 +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_PME_PLAT_CLK_DIV 1 +#define CONFIG_SYS_PME_CLK CONFIG_PME_PLAT_CLK_DIV +#define CONFIG_SYS_FM1_CLK 0 +#define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_4_7 +#define CONFIG_SYS_FSL_IFC_BANK_COUNT 8 +#define CONFIG_SYS_FMAN_V3 +#define CONFIG_SYS_FM_MURAM_SIZE 0x28000 +#define CONFIG_SYS_FSL_TBCLK_DIV 16 +#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v3.0" +#define CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE +#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 +#define CONFIG_SYS_FSL_SFP_VER_3_0 +#define CONFIG_SYS_FSL_ISBC_VER 2 + #elif defined(CONFIG_PPC_C29X) #define CONFIG_MAX_CPUS 1 #define CONFIG_FSL_SDHC_V2_3 diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index e47da1d..a46ccea 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -1854,6 +1854,12 @@ typedef struct ccsr_gur { #define FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT 24 #define FSL_CORENET2_RCWSR4_SRDS2_PRTCL 0x00fe0000 #define FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT 17 +#elif defined(CONFIG_PPC_T2080) || defined(CONFIG_PPC_T2081) +#define FSL_CORENET2_RCWSR4_SRDS1_PRTCL 0xff000000 +#define FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT 24 +#define FSL_CORENET2_RCWSR4_SRDS2_PRTCL 0x00ff0000 +#define FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT 16 +#define FSL_CORENET_RCWSR6_BOOT_LOC 0x0f800000 #endif #define FSL_CORENET2_RCWSR5_SRDS_PLL_PD_S1_PLL1 0x00800000 #define FSL_CORENET2_RCWSR5_SRDS_PLL_PD_S1_PLL2 0x00400000 @@ -1917,6 +1923,15 @@ typedef struct ccsr_gur { #define FSL_CORENET_RCWSR13_EC2_FM1_DTSEC6_RGMII 0x08000000 #define FSL_CORENET_RCWSR13_EC2_FM1_GPIO 0x10000000 #endif +#if defined(CONFIG_PPC_T2080) || defined(CONFIG_PPC_T2081) +#define FSL_CORENET_RCWSR13_EC1 0x60000000 /* bits 417..418 */ +#define FSL_CORENET_RCWSR13_EC1_DTSEC3_RGMII 0x00000000 +#define FSL_CORENET_RCWSR13_EC1_GPIO 0x40000000 +#define FSL_CORENET_RCWSR13_EC2 0x18000000 /* bits 419..420 */ +#define FSL_CORENET_RCWSR13_EC2_DTSEC4_RGMII 0x00000000 +#define FSL_CORENET_RCWSR13_EC2_DTSEC10_RGMII 0x08000000 +#define FSL_CORENET_RCWSR13_EC2_GPIO 0x10000000 +#endif u8 res18[192]; u32 scratchrw[4]; /* Scratch Read/Write */ u8 res19[240]; @@ -2913,6 +2928,7 @@ struct ccsr_pman { #define CONFIG_SYS_FSL_CPC_OFFSET 0x10000 #define CONFIG_SYS_MPC85xx_DMA1_OFFSET 0x100000 #define CONFIG_SYS_MPC85xx_DMA2_OFFSET 0x101000 +#define CONFIG_SYS_MPC85xx_DMA3_OFFSET 0x102000 #define CONFIG_SYS_MPC85xx_DMA_OFFSET CONFIG_SYS_MPC85xx_DMA1_OFFSET #define CONFIG_SYS_MPC85xx_ESPI_OFFSET 0x110000 #define CONFIG_SYS_MPC85xx_ESDHC_OFFSET 0x114000 diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h index 81f9d38..831804c 100644 --- a/arch/powerpc/include/asm/processor.h +++ b/arch/powerpc/include/asm/processor.h @@ -1127,6 +1127,8 @@ #define SVR_T1020 0x852100 #define SVR_T1021 0x852101 #define SVR_T1022 0x852102 +#define SVR_T2080 0x853000 +#define SVR_T2081 0x853100 #define SVR_8610 0x80A000 #define SVR_8641 0x809000 diff --git a/drivers/net/fm/Makefile b/drivers/net/fm/Makefile index bec86c1..bb8acff 100644 --- a/drivers/net/fm/Makefile +++ b/drivers/net/fm/Makefile @@ -26,6 +26,8 @@ obj-$(CONFIG_PPC_P4080) += p4080.o obj-$(CONFIG_PPC_P5020) += p5020.o obj-$(CONFIG_PPC_P5040) += p5040.o obj-$(CONFIG_PPC_T1040) += t1040.o +obj-$(CONFIG_PPC_T2080) += t2080.o +obj-$(CONFIG_PPC_T2081) += t2080.o obj-$(CONFIG_PPC_T4240) += t4240.o obj-$(CONFIG_PPC_T4160) += t4240.o obj-$(CONFIG_PPC_B4420) += b4860.o diff --git a/drivers/net/fm/t2080.c b/drivers/net/fm/t2080.c new file mode 100644 index 0000000..4187f85 --- /dev/null +++ b/drivers/net/fm/t2080.c @@ -0,0 +1,92 @@ +/* + * Copyright 2012 Freescale Semiconductor, Inc. + * + * Shengzhou Liu <Shengzhou.Liu(a)freescale.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <phy.h> +#include <fm_eth.h> +#include <asm/io.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_serdes.h> + +u32 port_to_devdisr[] = { + [FM1_DTSEC1] = FSL_CORENET_DEVDISR2_DTSEC1_1, + [FM1_DTSEC2] = FSL_CORENET_DEVDISR2_DTSEC1_2, + [FM1_DTSEC3] = FSL_CORENET_DEVDISR2_DTSEC1_3, + [FM1_DTSEC4] = FSL_CORENET_DEVDISR2_DTSEC1_4, + [FM1_DTSEC5] = FSL_CORENET_DEVDISR2_DTSEC1_5, + [FM1_DTSEC6] = FSL_CORENET_DEVDISR2_DTSEC1_6, + [FM1_DTSEC9] = FSL_CORENET_DEVDISR2_DTSEC1_9, + [FM1_DTSEC10] = FSL_CORENET_DEVDISR2_DTSEC1_10, + [FM1_10GEC1] = FSL_CORENET_DEVDISR2_10GEC1_1, + [FM1_10GEC2] = FSL_CORENET_DEVDISR2_10GEC1_2, + [FM1_10GEC3] = FSL_CORENET_DEVDISR2_10GEC1_3, + [FM1_10GEC4] = FSL_CORENET_DEVDISR2_10GEC1_4, +}; + +static int is_device_disabled(enum fm_port port) +{ + ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 devdisr2 = in_be32(&gur->devdisr2); + + return port_to_devdisr[port] & devdisr2; +} + +void fman_disable_port(enum fm_port port) +{ + ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + setbits_be32(&gur->devdisr2, port_to_devdisr[port]); +} + +phy_interface_t fman_port_enet_if(enum fm_port port) +{ + ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 rcwsr13 = in_be32(&gur->rcwsr[13]); + + if (is_device_disabled(port)) + return PHY_INTERFACE_MODE_NONE; + + if ((port == FM1_10GEC1 || port == FM1_10GEC2 || + port == FM1_10GEC3 || port == FM1_10GEC4) && + ((is_serdes_configured(XAUI_FM1_MAC9)) || + (is_serdes_configured(XFI_FM1_MAC1)) || + (is_serdes_configured(XFI_FM1_MAC2)) || + (is_serdes_configured(XFI_FM1_MAC9)) || + (is_serdes_configured(XFI_FM1_MAC10)))) + return PHY_INTERFACE_MODE_XGMII; + + if ((port == FM1_DTSEC3) && ((rcwsr13 & FSL_CORENET_RCWSR13_EC1) == + FSL_CORENET_RCWSR13_EC1_DTSEC3_RGMII)) + return PHY_INTERFACE_MODE_RGMII; + + if ((port == FM1_DTSEC4) && ((rcwsr13 & FSL_CORENET_RCWSR13_EC2) == + FSL_CORENET_RCWSR13_EC2_DTSEC4_RGMII)) + return PHY_INTERFACE_MODE_RGMII; + + if ((port == FM1_DTSEC10) && ((rcwsr13 & FSL_CORENET_RCWSR13_EC2) == + FSL_CORENET_RCWSR13_EC2_DTSEC10_RGMII)) + return PHY_INTERFACE_MODE_RGMII; + + switch (port) { + case FM1_DTSEC1: + case FM1_DTSEC2: + case FM1_DTSEC3: + case FM1_DTSEC4: + case FM1_DTSEC5: + case FM1_DTSEC6: + case FM1_DTSEC9: + case FM1_DTSEC10: + if (is_serdes_configured(SGMII_FM1_DTSEC1 + port - FM1_DTSEC1)) + return PHY_INTERFACE_MODE_SGMII; + break; + default: + return PHY_INTERFACE_MODE_NONE; + } + + return PHY_INTERFACE_MODE_NONE; +} -- 1.8.0

1 0

[U-Boot] [PATCH] mx6: Add initial support for Carrier1 mx6solo board
by Fabio Estevam 14 Nov '13

14 Nov '13

From: Fabio Estevam <fabio.estevam(a)freescale.com> Solid Run designed the Carrier1 board based on mx6q/dl/solo. Add the initial support for the mx6 solo variant. More information about this hardware can be found at: http://cubox-i.com/ Signed-off-by: Fabio Estevam <fabio.estevam(a)freescale.com> --- board/solidrun/carrier1/800mhz_2x256mx16.cfg | 74 +++++++ board/solidrun/carrier1/Makefile | 26 +++ board/solidrun/carrier1/README | 35 ++++ board/solidrun/carrier1/carrier1.c | 197 ++++++++++++++++++ board/solidrun/carrier1/clocks.cfg | 33 +++ board/solidrun/carrier1/ddr-800mhz-32bit-setup.cfg | 67 ++++++ board/solidrun/carrier1/mx6_c1solo.cfg | 25 +++ boards.cfg | 3 + include/configs/carrier1.h | 227 +++++++++++++++++++++ 9 files changed, 687 insertions(+) create mode 100644 board/solidrun/carrier1/800mhz_2x256mx16.cfg create mode 100644 board/solidrun/carrier1/Makefile create mode 100644 board/solidrun/carrier1/README create mode 100644 board/solidrun/carrier1/carrier1.c create mode 100644 board/solidrun/carrier1/clocks.cfg create mode 100644 board/solidrun/carrier1/ddr-800mhz-32bit-setup.cfg create mode 100644 board/solidrun/carrier1/mx6_c1solo.cfg create mode 100644 include/configs/carrier1.h diff --git a/board/solidrun/carrier1/800mhz_2x256mx16.cfg b/board/solidrun/carrier1/800mhz_2x256mx16.cfg new file mode 100644 index 0000000..c0398f0 --- /dev/null +++ b/board/solidrun/carrier1/800mhz_2x256mx16.cfg @@ -0,0 +1,74 @@ +/* + * Copyright (C) 2013 Boundary Devices + * Copyright (C) 2013 SolidRun ltd. + * Copyright (C) 2013 Jon Nettleton <jon.nettleton(a)gmail.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* ZQ Calibrations */ +DATA 4, MX6_MMDC_P0_MPZQHWCTRL, 0xa1390003 +DATA 4, MX6_MMDC_P1_MPZQHWCTRL, 0xa1390003 +/* write leveling */ +DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x000F0011 +DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x000E000F +/* + * DQS gating, read delay, write delay calibration values + * based on calibration compare of 0x00ffff00 + */ +DATA 4, MX6_MMDC_P0_MPDGCTRL0, 0x42240229 +DATA 4, MX6_MMDC_P0_MPDGCTRL1, 0x021a0219 +DATA 4, MX6_MMDC_P0_MPRDDLCTL, 0x4e4f5150 +DATA 4, MX6_MMDC_P0_MPWRDLCTL, 0x35363136 +/* read data bit delay */ +DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333 +DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333 +DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333 +DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333 +/* Complete calibration by forced measurement */ +DATA 4, MX6_MMDC_P0_MPMUR0, 0x00000800 +DATA 4, MX6_MMDC_P1_MPMUR0, 0x00000800 + +/* + * MMDC init: + * in DDR3, 32-bit mode, only MMDC0 is initiated: + */ +DATA 4, MX6_MMDC_P0_MDPDC, 0x0002002d +DATA 4, MX6_MMDC_P0_MDOTC, 0x00333030 + +DATA 4, MX6_MMDC_P0_MDCFG0, 0x40445323 +DATA 4, MX6_MMDC_P0_MDCFG1, 0xb68e8c63 + +DATA 4, MX6_MMDC_P0_MDCFG2, 0x01ff00db +DATA 4, MX6_MMDC_P0_MDMISC, 0x00001740 +DATA 4, MX6_MMDC_P0_MDSCR, 0x00008000 +DATA 4, MX6_MMDC_P0_MDRWD, 0x000026d2 +DATA 4, MX6_MMDC_P0_MDOR, 0x00440e21 +/* CS0_END - 0x2fffffff, 512M */ +DATA 4, MX6_MMDC_P0_MDASP, 0x00000017 + +/* MMDC0_MAARCR ADOPT optimized priorities. Dyn jump disabled */ +DATA 4, 0x021b0400, 0x11420000 + +/* MMDC0_MDCTL- row-14bits; col-10bits; burst length 8;32-bit data bus */ +DATA 4, MX6_MMDC_P0_MDCTL, 0x83190000 + +/* + * Initialize 2GB DDR3 - Micron MT41J128M + * MR2 + */ +DATA 4, MX6_MMDC_P0_MDSCR, 0x04008032 +/* MR3 */ +DATA 4, MX6_MMDC_P0_MDSCR, 0x00008033 +/* MR1 */ +DATA 4, MX6_MMDC_P0_MDSCR, 0x00428031 +/* MR0 */ +DATA 4, MX6_MMDC_P0_MDSCR, 0x07208030 +/* ZQ calibration */ +DATA 4, MX6_MMDC_P0_MDSCR, 0x04008040 +/* final DDR setup */ +DATA 4, MX6_MMDC_P0_MDREF, 0x00005800 +DATA 4, MX6_MMDC_P0_MPODTCTRL, 0x00000007 +DATA 4, MX6_MMDC_P0_MDPDC, 0x0002556d +DATA 4, MX6_MMDC_P0_MAPSR, 0x00011006 +DATA 4, MX6_MMDC_P0_MDSCR, 0x00000000 diff --git a/board/solidrun/carrier1/Makefile b/board/solidrun/carrier1/Makefile new file mode 100644 index 0000000..a18451e --- /dev/null +++ b/board/solidrun/carrier1/Makefile @@ -0,0 +1,26 @@ +# +# Copyright (C) 2013, Jon Nettleton <jon.nettleton(a)gmail.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := carrier1.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/solidrun/carrier1/README b/board/solidrun/carrier1/README new file mode 100644 index 0000000..89d0aa0 --- /dev/null +++ b/board/solidrun/carrier1/README @@ -0,0 +1,35 @@ +U-Boot for Solid Run Carrier1 +----------------------------- + +This file contains information for the port of U-Boot to the Carrier1 board. + +For more details about Carrier1, please refer to: +http://cubox-i.com + +Building U-boot for Carrier1 +---------------------------- + +To build U-Boot for the Carrier1 Solo version: + +$ make carrier1_solo_config +$ make + +Flashing U-boot into the SD card +-------------------------------- + +- After the 'make' command completes, the generated 'u-boot.imx' binary must be +flashed into the SD card: + +$ sudo dd if=u-boot.imx of=/dev/mmcblk0 bs=1k seek=1; sync + +(Note - the SD card node may vary, so adjust this as needed). + +- Insert the micro SD card into the slot located in the bottom of the board + +- Connect a 3.3V USB to serial converter cable to the host PC. The MX6 UART +signals are available in the 26 pin connector as shown at: +http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware +(Check for "26 pin header layout"). + +- Power up the board via USB cable (CON201) and U-boot messages will appear in +the serial console. diff --git a/board/solidrun/carrier1/carrier1.c b/board/solidrun/carrier1/carrier1.c new file mode 100644 index 0000000..9c4ec49 --- /dev/null +++ b/board/solidrun/carrier1/carrier1.c @@ -0,0 +1,197 @@ +/* + * Copyright (C) 2013 Freescale Semiconductor, Inc. + * Copyright (C) 2013 SolidRun ltd. + * Copyright (C) 2013 Jon Nettleton <jon.nettleton(a)gmail.com>. + * + * Author: Fabio Estevam <fabio.estevam(a)freescale.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <asm/arch/clock.h> +#include <asm/arch/crm_regs.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/iomux.h> +#include <asm/arch/mx6-pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/errno.h> +#include <asm/gpio.h> +#include <asm/imx-common/iomux-v3.h> +#include <asm/io.h> +#include <mmc.h> +#include <fsl_esdhc.h> +#include <miiphy.h> +#include <netdev.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ + PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ + PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ + PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CLK_CTRL (PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | \ + PAD_CTL_HYS) + +#define USDHC_PAD_GPIO_CTRL (PAD_CTL_PUS_22K_UP | \ + PAD_CTL_SPEED_LOW | PAD_CTL_DSE_40ohm | \ + PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) + +#define ENET_PAD_CTRL_PD (PAD_CTL_PUS_100K_DOWN | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) + +#define ENET_PAD_CTRL_CLK ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) + +#define ETH_PHY_RESET IMX_GPIO_NR(4, 15) + +int dram_init(void) +{ + gd->ram_size = ((phys_size_t)CONFIG_DDR_MB * 1024 * 1024); + + return 0; +} + +static iomux_v3_cfg_t const uart1_pads[] = { + MX6_PAD_CSI0_DAT10__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_CSI0_DAT11__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static void setup_iomux_uart(void) +{ + imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); +} + +static iomux_v3_cfg_t const usdhc2_pads[] = { + MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CLK_CTRL), + MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT0__USDHC2_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT1__USDHC2_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT2__USDHC2_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_GPIO_4__USDHC2_CD | MUX_PAD_CTRL(USDHC_PAD_GPIO_CTRL), +}; + +#ifdef CONFIG_FSL_ESDHC +static struct fsl_esdhc_cfg usdhc_cfg[1] = { + { USDHC2_BASE_ADDR }, +}; + +int board_mmc_getcd(struct mmc *mmc) +{ + return 1; /* SD card is the boot medium, so always present */ +} + +int board_mmc_init(bd_t *bis) +{ + imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); + + return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); +} +#endif + +#ifdef CONFIG_FEC_MXC +static iomux_v3_cfg_t const enet_pads[] = { + MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), + /* AR8035 reset */ + MX6_PAD_KEY_ROW4__GPIO_4_15 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD), + /* AR8035 interrupt */ + MX6_PAD_DI0_PIN2__GPIO_4_18 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* GPIO16 -> AR8035 25MHz */ + MX6_PAD_GPIO_16__ENET_ANATOP_ETHERNET_REF_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), + /* AR8035 CLK_25M --> ENET_REF_CLK (V22) */ + MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK), + MX6_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD), + MX6_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD), + MX6_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL_PD), +}; + +static void setup_iomux_enet(void) +{ + imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads)); + + /* Reset AR8035 PHY */ + gpio_direction_output(ETH_PHY_RESET, 0); + udelay(1000 * 2); /* Wait 2 ms before reset */ + gpio_set_value(ETH_PHY_RESET, 1); + + udelay(100); +} + +int board_phy_config(struct phy_device *phydev) +{ + if (phydev->drv->config) + phydev->drv->config(phydev); + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + int ret; + struct iomuxc_base_regs *iomuxc_regs = (struct iomuxc_base_regs *) + IOMUXC_BASE_ADDR; + struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; + s32 timeout = 100000; + + u32 reg = readl(&anatop->pll_enet); + reg |= 0x00002000; + writel(reg, &anatop->pll_enet); + + /* clear gpr1[21] */ + clrsetbits_le32(&iomuxc_regs->gpr[1], (1 << 21), 1); + + while (timeout--) { + if (readl(&anatop->pll_enet) & BM_ANADIG_PLL_ENET_LOCK) + break; + } + + setup_iomux_enet(); + + ret = cpu_eth_init(bis); + if (ret) + printf("FEC MXC: %s:failed: %d\n", __func__, ret); + + return ret; +} +#endif + +int board_early_init_f(void) +{ + setup_iomux_uart(); + + return 0; +} + +int board_init(void) +{ + /* address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + + return 0; +} + +int checkboard(void) +{ + puts("Board: MX6 Carrier1\n"); + + return 0; +} diff --git a/board/solidrun/carrier1/clocks.cfg b/board/solidrun/carrier1/clocks.cfg new file mode 100644 index 0000000..1288811 --- /dev/null +++ b/board/solidrun/carrier1/clocks.cfg @@ -0,0 +1,33 @@ +/* + * Copyright (C) 2013 Boundary Devices + * Copyright (C) 2013 SolidRun ltd. + * Copyright (C) 2013 Jon Nettleton <jon.nettleton(a)gmail.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* set the default clock gate to save power */ +DATA 4, CCM_CCGR0, 0x00C03F3F +DATA 4, CCM_CCGR1, 0x0030FC03 +DATA 4, CCM_CCGR2, 0x0FFFC000 +DATA 4, CCM_CCGR3, 0x3FF00000 +DATA 4, CCM_CCGR4, 0x00FFF300 +DATA 4, CCM_CCGR5, 0x0F0000C3 +DATA 4, CCM_CCGR6, 0x000003FF + +/* enable AXI cache for VDOA/VPU/IPU */ +DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF +/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ +DATA 4, MX6_IOMUXC_GPR6, 0x007F007F +DATA 4, MX6_IOMUXC_GPR7, 0x007F007F + +/* + * Setup CCM_CCOSR register as follows: + * + * cko1_en = 1 --> CKO1 enabled + * cko1_div = 111 --> divide by 8 + * cko1_sel = 1011 --> ahb_clk_root + * + * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz + */ +DATA 4, CCM_CCOSR, 0x000000fb diff --git a/board/solidrun/carrier1/ddr-800mhz-32bit-setup.cfg b/board/solidrun/carrier1/ddr-800mhz-32bit-setup.cfg new file mode 100644 index 0000000..f89a296 --- /dev/null +++ b/board/solidrun/carrier1/ddr-800mhz-32bit-setup.cfg @@ -0,0 +1,67 @@ +/* + * Copyright (C) 2013 Boundary Devices + * Copyright (C) 2013 SolidRun ltd. + * Copyright (C) 2013 Jon Nettleton <jon.nettleton(a)gmail.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* DDR IO TYPE */ +DATA 4, MX6_IOM_GRP_DDR_TYPE, 0x000c0000 +DATA 4, MX6_IOM_GRP_DDRPKE, 0x00000000 +/* Clock */ +DATA 4, MX6_IOM_DRAM_SDCLK_0, 0x00000030 +DATA 4, MX6_IOM_DRAM_SDCLK_1, 0x00000030 +/* Address */ +DATA 4, MX6_IOM_DRAM_CAS, 0x00000030 +DATA 4, MX6_IOM_DRAM_RAS, 0x00000030 +DATA 4, MX6_IOM_GRP_ADDDS, 0x00000030 +/* Control */ +DATA 4, MX6_IOM_DRAM_RESET, 0x00000030 +DATA 4, MX6_IOM_DRAM_SDCKE0, 0x00003000 +DATA 4, MX6_IOM_DRAM_SDCKE1, 0x00003000 +DATA 4, MX6_IOM_DRAM_SDBA2, 0x00000000 +DATA 4, MX6_IOM_DRAM_SDODT0, 0x00003030 +DATA 4, MX6_IOM_DRAM_SDODT1, 0x00003030 +DATA 4, MX6_IOM_GRP_CTLDS, 0x00000030 + +/* + * Data Strobe: IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL - DDR_INPUT=0, CMOS, + * CMOS mode saves power, but have less timing margin in case of DDR + * timing issue on your board you can try DDR_MODE: [= 0x00020000] + */ +DATA 4, MX6_IOM_DDRMODE_CTL, 0x00000000 + +DATA 4, MX6_IOM_DRAM_SDQS0, 0x00000030 +DATA 4, MX6_IOM_DRAM_SDQS1, 0x00000030 +DATA 4, MX6_IOM_DRAM_SDQS2, 0x00000030 +DATA 4, MX6_IOM_DRAM_SDQS3, 0x00000030 +DATA 4, MX6_IOM_DRAM_SDQS4, 0x00000000 +DATA 4, MX6_IOM_DRAM_SDQS5, 0x00000000 +DATA 4, MX6_IOM_DRAM_SDQS6, 0x00000000 +DATA 4, MX6_IOM_DRAM_SDQS7, 0x00000000 + +/* + * DATA:IOMUXC_SW_PAD_CTL_GRP_DDRMODE - DDR_INPUT=0, CMOS, + * CMOS mode saves power, but have less timing margin in case of DDR + * timing issue on your board you can try DDR_MODE: [= 0x00020000] + */ +DATA 4, MX6_IOM_GRP_DDRMODE, 0x00000000 + +DATA 4, MX6_IOM_GRP_B0DS, 0x00000030 +DATA 4, MX6_IOM_GRP_B1DS, 0x00000030 +DATA 4, MX6_IOM_GRP_B2DS, 0x00000030 +DATA 4, MX6_IOM_GRP_B3DS, 0x00000030 +DATA 4, MX6_IOM_GRP_B4DS, 0x00000000 +DATA 4, MX6_IOM_GRP_B5DS, 0x00000000 +DATA 4, MX6_IOM_GRP_B6DS, 0x00000000 +DATA 4, MX6_IOM_GRP_B7DS, 0x00000000 + +DATA 4, MX6_IOM_DRAM_DQM0, 0x00000030 +DATA 4, MX6_IOM_DRAM_DQM1, 0x00000030 +DATA 4, MX6_IOM_DRAM_DQM2, 0x00000030 +DATA 4, MX6_IOM_DRAM_DQM3, 0x00000030 +DATA 4, MX6_IOM_DRAM_DQM4, 0x00000000 +DATA 4, MX6_IOM_DRAM_DQM5, 0x00000000 +DATA 4, MX6_IOM_DRAM_DQM6, 0x00000000 +DATA 4, MX6_IOM_DRAM_DQM7, 0x00000000 diff --git a/board/solidrun/carrier1/mx6_c1solo.cfg b/board/solidrun/carrier1/mx6_c1solo.cfg new file mode 100644 index 0000000..1acad07 --- /dev/null +++ b/board/solidrun/carrier1/mx6_c1solo.cfg @@ -0,0 +1,25 @@ +/* + * Copyright (C) 2013 Boundary Devices + * Copyright (C) 2013 Jon Nettleton <jon.nettleton(a)gmail.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* image version */ +IMAGE_VERSION 2 + +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ +BOOT_FROM sd + +#define __ASSEMBLY__ +#include <config.h> +#include "asm/arch/mx6-ddr.h" +#include "asm/arch/iomux.h" +#include "asm/arch/crm_regs.h" + +#include "ddr-800mhz-32bit-setup.cfg" +#include "800mhz_2x256mx16.cfg" +#include "clocks.cfg" diff --git a/boards.cfg b/boards.cfg index cec154b..892973a 100644 --- a/boards.cfg +++ b/boards.cfg @@ -306,6 +306,9 @@ Active arm armv7 mx6 freescale mx6sabresd Active arm armv7 mx6 freescale mx6sabresd mx6qsabresd mx6sabresd:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg,MX6Q Fabio Estevam <fabio.estevam(a)freescale.com> Active arm armv7 mx6 freescale mx6slevk mx6slevk mx6slevk:IMX_CONFIG=board/freescale/mx6slevk/imximage.cfg,MX6SL Fabio Estevam <fabio.estevam(a)freescale.com> Active arm armv7 mx6 freescale titanium titanium titanium:IMX_CONFIG=board/freescale/titanium/imximage.cfg Stefan Roese <sr(a)denx.de> + +Active arm armv7 mx6 solidrun carrier1 carrier1_solo carrier1:IMX_CONFIG=board/solidrun/carrier1/mx6_c1solo.cfg,MX6S,DDR_MB=512 Fabio Estevam <fabio.estevam(a)freescale.com> + Active arm armv7 omap3 - overo omap3_overo - Steve Sakoman <sakoman(a)gmail.com> Active arm armv7 omap3 - pandora omap3_pandora - Grazvydas Ignotas <notasas(a)gmail.com> Active arm armv7 omap3 8dtech eco5pk eco5pk - Raphael Assenat <raph(a)8d.com> diff --git a/include/configs/carrier1.h b/include/configs/carrier1.h new file mode 100644 index 0000000..969e3ad --- /dev/null +++ b/include/configs/carrier1.h @@ -0,0 +1,227 @@ +/* + * Copyright (C) 2013 Freescale Semiconductor, Inc. + * Copyright (C) 2013 SolidRun ltd. + * Copyright (C) 2013 Jon Nettleton <jon.nettleton(a)gmail.com> + * + * Configuration settings for the SolidRun Carrier1 board. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include "mx6_common.h" +#include <asm/arch/imx-regs.h> +#include <asm/imx-common/gpio.h> +#include <asm/sizes.h> + +#define CONFIG_MX6 +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#define MACH_TYPE_CARRIER1 4773 +#define CONFIG_MACH_TYPE MACH_TYPE_CARRIER1 + +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_REVISION_TAG + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (2 * SZ_1M) + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_MXC_GPIO + +#define CONFIG_MXC_UART +#define CONFIG_MXC_UART_BASE UART1_BASE + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 + +/* Command definition */ +#include <config_cmd_default.h> + +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_I2C + +#define CONFIG_CMD_BMODE +#define CONFIG_CMD_SETEXPR + +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_LOADADDR 0x12000000 +#define CONFIG_SYS_TEXT_BASE 0x17800000 + +/* MMC Configuration */ +#define CONFIG_FSL_ESDHC +#define CONFIG_FSL_USDHC +#define CONFIG_SYS_FSL_USDHC_NUM 1 +#define CONFIG_SYS_FSL_ESDHC_ADDR 0 +#define CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_BOUNCE_BUFFER +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION + +/* Ethernet Configuration */ +#define CONFIG_FEC_MXC +#ifdef CONFIG_FEC_MXC +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_FEC_MXC +#define CONFIG_MII +#define IMX_FEC_BASE ENET_BASE_ADDR +#define CONFIG_FEC_XCV_TYPE RGMII +#define CONFIG_ETHPRIME "FEC" +#define CONFIG_FEC_MXC_PHYADDR 0 +#define CONFIG_PHYLIB +#define CONFIG_PHY_ATHEROS +#endif + +#if defined(CONFIG_MX6S) +#define CONFIG_DEFAULT_FDT_FILE "imx6dl-carrier1.dtb" +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "script=boot.scr\0" \ + "uimage=uImage\0" \ + "console=ttymxc0\0" \ + "splashpos=m,m\0" \ + "fdt_high=0xffffffff\0" \ + "initrd_high=0xffffffff\0" \ + "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ + "fdt_addr=0x11000000\0" \ + "boot_fdt=try\0" \ + "ip_dyn=yes\0" \ + "mmcdev=0\0" \ + "mmcpart=1\0" \ + "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \ + "update_sd_firmware_filename=u-boot.imx\0" \ + "update_sd_firmware=" \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "if mmc dev ${mmcdev}; then " \ + "if ${get_cmd} ${update_sd_firmware_filename}; then " \ + "setexpr fw_sz ${filesize} / 0x200; " \ + "setexpr fw_sz ${fw_sz} + 1; " \ + "mmc write ${loadaddr} 0x2 ${fw_sz}; " \ + "fi; " \ + "fi\0" \ + "mmcargs=setenv bootargs console=${console},${baudrate} " \ + "root=${mmcroot}\0" \ + "loadbootscript=" \ + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if run loadfdt; then " \ + "bootm ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootm; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootm; " \ + "fi;\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${uimage}; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ + "bootm ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootm; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootm; " \ + "fi;\0" + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loaduimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else run netboot; fi" + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT "=> " +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 1024 + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_CMDLINE_EDITING + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* FLASH and environment organization */ +#define CONFIG_SYS_NO_FLASH + +#define CONFIG_ENV_SIZE (8 * 1024) + +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_OFFSET (6 * 64 * 1024) +#define CONFIG_SYS_MMC_ENV_DEV 0 + +#define CONFIG_OF_LIBFDT +#define CONFIG_CMD_BOOTZ + +#ifndef CONFIG_SYS_DCACHE_OFF +#define CONFIG_CMD_CACHE +#endif + +#endif /* __CONFIG_H * */ -- 1.8.1.2

2 3

[U-Boot] [PATCH v3 0/6] arm: atmel: sama5d3: enable spl boot from SD card
by Bo Shen 14 Nov '13

14 Nov '13

This patch series enable spl boot from SD card, it only can boot u-boot itself. Changes in v3: - Correct the clock enable code, the ID can not OR - Move to at91 common folder - Move plla and mck configure to spl.c file Changes in v2: - Move spl related code to at91-common folder Bo Shen (6): arm: atmel: sama5d3: correct the ID for DBGU and PIT arm: atmel: sama5d3: correct the error define of DIV arm: atmel: sama5d3: the offset of MULA is 18 arm: atmel: sama5d3: early enable PIO peripherals arm: atmel: add ddr2 initialization function arm: atmel: sama5d3: spl boot from fat fs SD card arch/arm/cpu/armv7/Makefile | 2 +- arch/arm/cpu/armv7/at91/sama5d3_devices.c | 2 +- arch/arm/cpu/armv7/at91/timer.c | 2 +- arch/arm/cpu/at91-common/Makefile | 33 +++++++ arch/arm/cpu/at91-common/mpddrc.c | 123 +++++++++++++++++++++++++ arch/arm/cpu/at91-common/spl.c | 90 ++++++++++++++++++ arch/arm/cpu/at91-common/u-boot-spl.lds | 50 ++++++++++ arch/arm/include/asm/arch-at91/at91_common.h | 4 + arch/arm/include/asm/arch-at91/at91_pmc.h | 8 +- arch/arm/include/asm/arch-at91/atmel_mpddrc.h | 111 ++++++++++++++++++++++ arch/arm/include/asm/arch-at91/spl.h | 20 ++++ board/atmel/sama5d3xek/sama5d3xek.c | 88 ++++++++++++++++++ include/configs/sama5d3xek.h | 34 +++++++ spl/Makefile | 4 + 14 files changed, 566 insertions(+), 5 deletions(-) create mode 100644 arch/arm/cpu/at91-common/Makefile create mode 100644 arch/arm/cpu/at91-common/mpddrc.c create mode 100644 arch/arm/cpu/at91-common/spl.c create mode 100644 arch/arm/cpu/at91-common/u-boot-spl.lds create mode 100644 arch/arm/include/asm/arch-at91/atmel_mpddrc.h create mode 100644 arch/arm/include/asm/arch-at91/spl.h -- 1.7.9.5

4 20

[U-Boot] NAND BBI swap on iMX53
by Luca Ellero 14 Nov '13

14 Nov '13

Hi all, I've noticed that mxc_nand driver doesn't implement BBI swap for reading factory marked bad blocks on NAND devices, as suggested by Freescale: https://community.freescale.com/servlet/JiveServlet/download/329191-260869/… BBI swap is implemented in Freescale iMX53 BSP (which use an old u-boot version 2009.08) but not DENX official U-Boot. Isn't this a dangerous behaviour? As far as as I can see it can lead to an irreparable loss of factory bad blocks markers. Can someone please give me some information about this topic. Thanks Best regards Luca Ellero

1 0