January 2013 - U-Boot

[U-Boot] [PATCH] tools: imximage: Load a size that is multiple of 512
by Fabio Estevam 03 Jan '13

03 Jan '13

In order to mx53 ROM to properly load the U-boot image, its size should be multiple of 512 bytes. This issue was observed on gcc 4.6.2/4.7.3 which caused data aborts: U-Boot 2013.01-rc2-00172-gf8cfcf1-dirty (Dec 26 2012 - 13:13:28) Board: MX53 LOCO I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial CPU: Freescale i.MX53 family rev2.1 at 1000 MHz Reset cause: WDOG Net: FEC Warning: FEC using MAC address from net device Hit any key to stop autoboot: 0 data abort MAYBE you should read doc/README.arm-unaligned-accesses pc : [<aff72220>] lr : [<aff721fc>] sp : af565e20 ip : af566918 fp : 00000000 r10: 00000003 r9 : affabb5b r8 : af565f58 r7 : 00000000 r6 : 36747fff r5 : af5668e8 r4 : 36747fff r3 : af5668ec r2 : af5668eb r1 : 00000000 r0 : af5668e8 Flags: NzcV IRQs off FIQs off Mode SVC_32 Resetting CPU ... resetting ... ,and this patch fixes it. Signed-off-by: Troy Kisky <troy.kisky(a)boundarydevices.com> Signed-off-by: Fabio Estevam <fabio.estevam(a)freescale.com> --- include/image.h | 3 +++ tools/imximage.c | 9 ++++++++- 2 files changed, 11 insertions(+), 1 deletion(-) diff --git a/include/image.h b/include/image.h index f54d983..e1e83b4 100644 --- a/include/image.h +++ b/include/image.h @@ -179,6 +179,9 @@ #define IH_MAGIC 0x27051956 /* Image Magic Number */ #define IH_NMLEN 32 /* Image Name Length */ +/* Reused from common.h */ +#define ROUND(a, b) (((a) + (b) - 1) & ~((b) - 1)) + /* * Legacy format image header, * all data in network byte order (aka natural aka bigendian). diff --git a/tools/imximage.c b/tools/imximage.c index 63f88b6..a93d7eb 100644 --- a/tools/imximage.c +++ b/tools/imximage.c @@ -515,7 +515,14 @@ static void imximage_set_header(void *ptr, struct stat *sbuf, int ifd, /* Set the imx header */ (*set_imx_hdr)(imxhdr, dcd_len, params->ep, imxhdr->flash_offset); - *header_size_ptr = sbuf->st_size + imxhdr->flash_offset; + + /* + * ROM bug alert + * mx53 only loads 512 byte multiples. + * The remaining fraction of a block bytes would + * not be loaded. + */ + *header_size_ptr = ROUND(sbuf->st_size + imxhdr->flash_offset, 512); } int imximage_check_params(struct mkimage_params *params) -- 1.7.9.5

1 0

[U-Boot] [PATCH] drivers/block/systemace: fixes read/write words for bus width = 8
by Alexey Brodkin 03 Jan '13

03 Jan '13

From: Alexey Brodkin <abrodkin(a)synopsys.com> Current implementation works fine for bus width = 16 bits because we never get into "if" branch. If one sets width to 8 bits there will be 2 consequent data accesses (read/write): 1. Correct data access for 8-bit bus 2. Unconditional (and in this case incorrect) data access as if data bus is 16-bit wide Signed-off-by: Alexey Brodkin <abrodkin(a)synopsys.com> --- drivers/block/systemace.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/block/systemace.c b/drivers/block/systemace.c index 247cf06..88561a7 100644 --- a/drivers/block/systemace.c +++ b/drivers/block/systemace.c @@ -66,7 +66,8 @@ static void ace_writew(u16 val, unsigned off) writeb(val >> 8, base + off + 1); #endif } - out16(base + off, val); + else + out16(base + off, val); } static u16 ace_readw(unsigned off) @@ -78,8 +79,8 @@ static u16 ace_readw(unsigned off) return readb(base + off) | (readb(base + off + 1) << 8); #endif } - - return in16(base + off); + else + return in16(base + off); } static unsigned long systemace_read(int dev, unsigned long start, -- 1.7.10.4

4 12

[U-Boot] [PATCH 2/2] EXYNOS: EXYNOS5250: add gpio structure for EXYNOS5250
by Donghwa Lee 03 Jan '13

03 Jan '13

This patch add gpio structure of exynos5250. Exynos5xxx series has each different gpio bank, so it is needed to separate. After separation task, useless variables will be removed. Signed-off-by: Donghwa Lee <dh09.lee(a)samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park(a)samsung.com> --- arch/arm/include/asm/arch-exynos/gpio.h | 80 +++++++++++++++++++++++++++++++ 1 files changed, 80 insertions(+), 0 deletions(-) diff --git a/arch/arm/include/asm/arch-exynos/gpio.h b/arch/arm/include/asm/arch-exynos/gpio.h index cfe1024..be84b87 100644 --- a/arch/arm/include/asm/arch-exynos/gpio.h +++ b/arch/arm/include/asm/arch-exynos/gpio.h @@ -196,6 +196,62 @@ struct exynos5_gpio_part4 { struct s5p_gpio_bank z; }; +struct exynos5250_gpio_part1 { + struct s5p_gpio_bank a0; + struct s5p_gpio_bank a1; + struct s5p_gpio_bank a2; + struct s5p_gpio_bank b0; + struct s5p_gpio_bank b1; + struct s5p_gpio_bank b2; + struct s5p_gpio_bank b3; + struct s5p_gpio_bank c0; + struct s5p_gpio_bank c1; + struct s5p_gpio_bank c2; + struct s5p_gpio_bank c3; + struct s5p_gpio_bank d0; + struct s5p_gpio_bank d1; + struct s5p_gpio_bank y0; + struct s5p_gpio_bank y1; + struct s5p_gpio_bank y2; + struct s5p_gpio_bank y3; + struct s5p_gpio_bank y4; + struct s5p_gpio_bank y5; + struct s5p_gpio_bank y6; + struct s5p_gpio_bank res1[0x3]; + struct s5p_gpio_bank c4; + struct s5p_gpio_bank res2[0x48]; + struct s5p_gpio_bank x0; + struct s5p_gpio_bank x1; + struct s5p_gpio_bank x2; + struct s5p_gpio_bank x3; +}; + +struct exynos5250_gpio_part2 { + struct s5p_gpio_bank e0; + struct s5p_gpio_bank e1; + struct s5p_gpio_bank f0; + struct s5p_gpio_bank f1; + struct s5p_gpio_bank g0; + struct s5p_gpio_bank g1; + struct s5p_gpio_bank g2; + struct s5p_gpio_bank h0; + struct s5p_gpio_bank h1; +}; + +struct exynos5250_gpio_part3 { + struct s5p_gpio_bank v0; + struct s5p_gpio_bank v1; + struct s5p_gpio_bank res1[0x1]; + struct s5p_gpio_bank v2; + struct s5p_gpio_bank v3; + struct s5p_gpio_bank res2[0x1]; + struct s5p_gpio_bank v4; +}; + +struct exynos5250_gpio_part4 { + struct s5p_gpio_bank z; +}; + /* functions */ void s5p_gpio_cfg_pin(struct s5p_gpio_bank *bank, int gpio, int cfg); void s5p_gpio_direction_output(struct s5p_gpio_bank *bank, int gpio, int en); @@ -272,6 +328,30 @@ void s5p_gpio_set_rate(struct s5p_gpio_bank *bank, int gpio, int mode); - EXYNOS5_GPIO_PART3_BASE) / sizeof(struct s5p_gpio_bank)) \ * GPIO_PER_BANK) + pin) + EXYNOS5_GPIO_PART2_MAX) +#define exynos5250_gpio_part1_get_nr(bank, pin) \ + ((((((unsigned int) &(((struct exynos5250_gpio_part1 *) \ + EXYNOS5250_GPIO_PART1_BASE)->bank)) \ + - EXYNOS5250_GPIO_PART1_BASE) / sizeof(struct s5p_gpio_bank)) \ + * GPIO_PER_BANK) + pin) + +#define EXYNOS5250_GPIO_PART1_MAX ((sizeof(struct exynos5250_gpio_part1) \ + / sizeof(struct s5p_gpio_bank)) * GPIO_PER_BANK) + +#define exynos5250_gpio_part2_get_nr(bank, pin) \ + (((((((unsigned int) &(((struct exynos5250_gpio_part2 *) \ + EXYNOS5250_GPIO_PART2_BASE)->bank)) \ + - EXYNOS52590_GPIO_PART2_BASE) / sizeof(struct s5p_gpio_bank)) \ + * GPIO_PER_BANK) + pin) + EXYNOS5250_GPIO_PART1_MAX) + +#define EXYNOS5250_GPIO_PART2_MAX ((sizeof(struct exynos5250_gpio_part2) \ + / sizeof(struct s5p_gpio_bank)) * GPIO_PER_BANK) + +#define exynos5250_gpio_part3_get_nr(bank, pin) \ + (((((((unsigned int) &(((struct exynos5250_gpio_part3 *) \ + EXYNOS5250_GPIO_PART3_BASE)->bank)) \ + - EXYNOS5250_GPIO_PART3_BASE) / sizeof(struct s5p_gpio_bank)) \ + * GPIO_PER_BANK) + pin) + EXYNOS5250_GPIO_PART2_MAX) + static inline unsigned int s5p_gpio_base(int nr) { if (cpu_is_exynos5()) { -- 1.7.4.1

1 0

[U-Boot] [PATCH 1/2] EXYNOS: EXYNOS5250: add exynos5250 register addresses
by Donghwa Lee 03 Jan '13

03 Jan '13

This patch add exynos5250 register addresses. Exynos5xxx series has each different register, so it is needed to separate. Signed-off-by: Donghwa Lee <dh09.lee(a)samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park(a)samsung.com> --- arch/arm/include/asm/arch-exynos/cpu.h | 33 ++++++++++++++++++++++++++++++++ 1 files changed, 33 insertions(+), 0 deletions(-) diff --git a/arch/arm/include/asm/arch-exynos/cpu.h b/arch/arm/include/asm/arch-exynos/cpu.h index eb34422..0b382be 100644 --- a/arch/arm/include/asm/arch-exynos/cpu.h +++ b/arch/arm/include/asm/arch-exynos/cpu.h @@ -130,6 +130,37 @@ #define EXYNOS5_ADC_BASE DEVICE_NOT_AVAILABLE #define EXYNOS5_MODEM_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS5250_GPIO_PART4_BASE 0x03860000 +#define EXYNOS5250_PRO_ID 0x10000000 +#define EXYNOS5250_CLOCK_BASE 0x10010000 +#define EXYNOS5250_POWER_BASE 0x10040000 +#define EXYNOS5250_SWRESET 0x10040400 +#define EXYNOS5250_SYSREG_BASE 0x10050000 +#define EXYNOS5250_WATCHDOG_BASE 0x101D0000 +#define EXYNOS5250_DMC_PHY0_BASE 0x10C00000 +#define EXYNOS5250_DMC_PHY1_BASE 0x10C10000 +#define EXYNOS5250_GPIO_PART3_BASE 0x10D10000 +#define EXYNOS5250_DMC_CTRL_BASE 0x10DD0000 +#define EXYNOS5250_GPIO_PART1_BASE 0x11400000 +#define EXYNOS5250_MIPI_DSIM_BASE 0x11D00000 +#define EXYNOS5250_USB_HOST_EHCI_BASE 0x12110000 +#define EXYNOS5250_USBPHY_BASE 0x12130000 +#define EXYNOS5250_USBOTG_BASE 0x12140000 +#define EXYNOS5250_MMC_BASE 0x12200000 +#define EXYNOS5250_SROMC_BASE 0x12250000 +#define EXYNOS5250_UART_BASE 0x12C00000 +#define EXYNOS5250_I2C_BASE 0x12C60000 +#define EXYNOS5250_SPI_BASE 0x12D20000 +#define EXYNOS5250_I2S_BASE 0x12D60000 +#define EXYNOS5250_PWMTIMER_BASE 0x12DD0000 +#define EXYNOS5250_SPI_ISP_BASE 0x131A0000 +#define EXYNOS5250_GPIO_PART2_BASE 0x13400000 +#define EXYNOS5250_FIMD_BASE 0x14400000 +#define EXYNOS5250_DP_BASE 0x145B0000 + +#define EXYNOS5250_ADC_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS5250_MODEM_BASE DEVICE_NOT_AVAILABLE + #ifndef __ASSEMBLY__ #include <asm/io.h> /* CPU detection macros */ @@ -198,6 +229,8 @@ static inline unsigned int samsung_get_base_##device(void) \ return EXYNOS4X12_##base; \ return EXYNOS4_##base; \ } else if (cpu_is_exynos5()) { \ + if (proid_is_exynos5250()) \ + return EXYNOS5250_##base; \ return EXYNOS5_##base; \ } \ return 0; \ -- 1.7.4.1

1 0

[U-Boot] [PATCH 0/2] EXYNOS: EXYNOS5250: Separate setting configuration of exynos5250 from exynos5
by Donghwa Lee 03 Jan '13

03 Jan '13

Hi, Exynos5xxx series have each different HW configurations, for example, some register addresses, gpio banks configuration, and so on. So, each series are needed to separate from existing exynos5 configuration. [1/2] EXYNOS: EXYNOS5250: add exynos5250 register addresses [2/2] EXYNOS: EXYNOS5250: add gpio structure for EXYNOS5250 Thank you, Donghwa Lee

1 0

[U-Boot] Pull request: u-boot-arm/master
by Albert ARIBAUD 03 Jan '13

03 Jan '13

Hello Tom, The following changes since commit 095728803eedfce850a2f85828f79500cb09979e: Merge branch 'master' of git://git.denx.de/u-boot-net (2012-12-17 18:39:50 -0700) are available in the git repository at: git://git.denx.de/u-boot-arm master for you to fetch changes up to 96764df1b47ddebfb50fadf5af72530b07b5fc89: Merge samsung, imx, tegra into u-boot-arm/master (2012-12-22 11:59:14 +0100) This pull request is specifically to get past the big merge issues from u-boot-arm to u-boot which involved samsung, ixm and tegra fixes, thanks to all those who took part in helping untie the knot. Once this is in, I'll certainly have another pull request, early in the coming week. ---------------------------------------------------------------- Albert ARIBAUD (2): Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' Merge samsung, imx, tegra into u-boot-arm/master Allen Martin (2): tegra: add CONSOLE_MUX support to tegra-kbc Merge remote-tracking branch 'u-boot/master' into u-boot-arm-merged Ashok Kumar Reddy (1): ARM: arm1176: Define arch_cpu_init() for s3c64xx Benoît Thébaudeau (17): arm1136: Fix enable_caches() mx31: Move EHCI definitions to ehci-fsl.h ehci-mxc: Clean up ehci-mx5: Clean up ehci-mx5: Fix OC_DIS usage ehci-mx5: Fix OPM usage ehci-mx5: Fix *PM usage for i.MX53 ehci-mx5: Add missing OC_DIS for i.MX53 ehci-mxc: Make EHCI power/oc polarities configurable ehci-mxc: Make i.MX25 EHCI configurable ehci-mxc: Define host offsets ehci-mxc: Add support for i.MX35 mx35pdk: Add support for OTG ehci-mx5/6: Make board_ehci_hcd_init() optional ehci-mxc: Fix host power mask bit for i.MX35 ehci-mxc: Fix host power mask bit for i.MX25 mx5: Mark lowlevel_init board-specific code Chander Kashyap (1): Exynos5250: Enable PXE Support Fabio Estevam (28): mx25pdk: Include CONFIG_MX25 mx25pdk: Add esdhc support pmic_fsl: Introduce FSL_PMIC_I2C_LENGTH mx25: Place common functions into sys_proto.h pmic: Add support for mc34704 mx25pdk: Add Ethernet support mx53loco: Allow booting a zImage kernel mx25pdk: Allow booting a zImage kernel mx51evk: Allow booting a zImage kernel mx35pdk: Allow booting a zImage kernel mx6qsabre_common: Allow booting a zImage kernel mx5: Align SPI CS naming with i.MX53 reference manual mx5: Print CSPI clock in 'clock' command spi: mxc_spi: Fix handling of chip select spi: mxc_spi: Fix spi clock glitch durant reset mx6: clock: Only show CSPI clock if CSPI is enabled mx28evk: Configure CONFIG_BOOTDELAY to one second mx53loco: Configure CONFIG_BOOTDELAY to one second mx6qsabrelite: Configure CONFIG_BOOTDELAY to one second mx6qsabre_common: Configure CONFIG_BOOTDELAY to one second mx51evk: Configure CONFIG_BOOTDELAY to one second mx25pdk: Configure CONFIG_BOOTDELAY to one second mx31pdk: Configure CONFIG_BOOTDELAY to one second mx35pdk: Configure CONFIG_BOOTDELAY to one second mx25pdk: Adapt it for the new PMIC framework woodburn: Set gpio value in gpio_direction_output() mx53loco: Fix PMIC name mx25pdk: Allow booting a device tree kernel Hatim RV (3): EXYNOS: Add clock for SPI EXYNOS5: Add base address for SPI EXYNOS5: Enable SPI Marek Vasut (9): dm: wdt: Move s5p watchdog timer to drivers/watchdog/ mx28: Fix typo in POWER_MINPWR_VBG_OFF mx28: Fix typo in POWER_DCLIMITS_NEGLIMIT_OFFSET mx28: Remove SET, CLR, TOG ops from PLLxCTRL1 registers mx28: Rename regs-power.h to regs-power-mx28.h mxs: Silence elftosb mxs: Implement common function to setup VDDx mxs: Properly setup VDDD in power supply setup code mxs: Staticize SPL functions Mayuresh Kulkarni (1): tegra: Enable display/lcd support on Seaboard Minkyu Kang (6): ARCH: EXYNOS: add support to match product id EXYNOS: Clock: Add common function for pll rate calculation s3c64xx: fix the compiler error and warning Merge branch 'master' of git://git.denx.de/u-boot into resolve universal_c210: fix compiler error and compiler warning universal_c210: check the NULL pointer when get the PMIC Otavio Salvador (1): mxs: SPL: Generalize memory initialization Piotr Wilczek (12): arm:exynos4:trats: Correct SDRAM configuration for trats arm:exynos4:trats: Fix SDRAM size arm:exynos4:pinmux: Modify the gpio function for mmc arm:exynos4:trats: Use pinmux for mmc configuration arm:exynos4:universal: Use pinmux for mmc configuration arm:exynos4:universal: Eliminated low level init arm: trats: Power down core 1 exynos4: universal_C210: use software SPI misc:max8998 Add LDO macros drivers: video: Add ld9040 video driver drivers: video: fix image position exynos4: universal_C210: add display support Rajeshwari Shinde (16): PMIC: MAX77686: Add support for MAX77686 SMDK5250: Config: Enable MAX77686 pmic chip SOUND: SAMSUNG: Add I2S driver SOUND: Add WM8994 codec Sound: Add command for audio playback EXYNOS: Add I2S registers EXYNOS: Add parameters required by I2S EXYNOS: Add pinmux for I2S EXYNOS: Add I2S base address EXYNOS: Add clock for I2S SMDK5250: Enable Sound EXYNOS5: Add pinmux support for SPI SPI: Add SPI Driver for EXYNOS. EXYNOS5: Enable SPI booting. POWER: MAX77686: Modified as per the latest Implementation SMDK5250: Enable pmic MAX77686 Simon Glass (17): pxa: Disable dcache on palmld, palmtc, zipitz2 tegra: Use const for pinmux_config_pingroup/table() tegra: Add display support to funcmux tegra: fdt: Add pwm binding and node tegra: fdt: Add LCD definitions for Tegra tegra: Add support for PWM tegra: Add LCD driver tegra: Add LCD support to Nvidia boards arm: Add control over cachability of memory regions lcd: Add CONFIG_LCD_ALIGNMENT to select frame buffer alignment lcd: Add support for flushing LCD fb from dcache after update tegra: Align LCD frame buffer to section boundary tegra: Support control of cache settings for LCD tegra: fdt: Add LCD definitions for Seaboard lcd: Add CONFIG_CONSOLE_SCROLL_LINES option to speed console tegra: Remove unnecessary CONFIG_SYS_NAND_BASE tegra: config: seaboard: Move tegra-common-post to correct place Stefano Babic (9): ARM: Fix start.S when used with SPL in arm1136 MX35: add LOW_LEVEL_SRAM_STACK to use SPL_FRAMEWORK MX35: Add soc_boot_mode and soc_boot_device to MX35 SPL: Added SPL target for mx35 SOC to SPL Makefile ARM: Add SPL target to arm1136 MX35: add support for woodburn board MX5: added CONFIG_PMIC_FSL_MC13892 to mx53evk Merge git://git.denx.de/u-boot Merge branch 'master' of git://git.denx.de/u-boot into master Stephen Warren (4): ARM: tegra: TrimSlice: add support for USB1 port mmc: tegra: support 4-bit operation too on 8-bit slots ARM: tegra: enable 8-bit SD slots in board files tegra: use generic fs commands in BOOTCOMMAND Troy Kisky (4): mx6: soc: update get_cpu_rev and get_imx_type for mx6solo/sololite mx6: use CONFIG_MX6 instead of CONFIG_MX6Q imx-common: cpu: add imx_ddr_size arch-mx6: add mx6dl_pins.h Wei Ni (1): tegra: Add SOC support for display/lcd Łukasz Majewski (1): gpio:fix: Proper handling of GPIO subsystem parts at Samsung devices MAINTAINERS | 1 + Makefile | 4 +- README | 16 ++- arch/arm/cpu/arm1136/config.mk | 3 + arch/arm/cpu/arm1136/cpu.c | 22 ++-- arch/arm/cpu/arm1136/mx35/Makefile | 1 + arch/arm/cpu/arm1136/mx35/generic.c | 75 +++++++++++ arch/arm/cpu/arm1136/mx35/mx35_sdram.c | 137 ++++++++++++++++++++ arch/arm/cpu/arm1136/start.S | 31 +++-- arch/arm/cpu/arm1136/u-boot-spl.lds | 62 +++++++++ arch/arm/cpu/arm1176/s3c64xx/Makefile | 2 +- arch/arm/cpu/arm1176/s3c64xx/init.c | 26 ++++ arch/arm/cpu/arm926ejs/mxs/spl_boot.c | 4 +- arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c | 38 +++--- arch/arm/cpu/arm926ejs/mxs/spl_power_init.c | 305 ++++++++++++++++---------------------------- arch/arm/cpu/armv7/cache_v7.c | 11 ++ arch/arm/cpu/armv7/exynos/clock.c | 350 +++++++++++++++++++++++++++++++++++++++++---------- arch/arm/cpu/armv7/exynos/pinmux.c | 64 ++++++++++ arch/arm/cpu/armv7/mx5/clock.c | 4 +- arch/arm/cpu/armv7/mx5/lowlevel_init.S | 2 +- arch/arm/cpu/armv7/mx6/clock.c | 2 + arch/arm/cpu/armv7/mx6/soc.c | 32 +++-- arch/arm/cpu/armv7/s5p-common/Makefile | 1 - arch/arm/cpu/armv7/tegra20/Makefile | 2 + arch/arm/cpu/armv7/tegra20/display.c | 409 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ arch/arm/cpu/armv7/tegra20/pwm.c | 101 +++++++++++++++ arch/arm/cpu/tegra20-common/funcmux.c | 37 ++++++ arch/arm/cpu/tegra20-common/pinmux.c | 4 +- arch/arm/dts/tegra20.dtsi | 105 ++++++++++++++++ arch/arm/imx-common/cpu.c | 66 ++++++++-- arch/arm/include/asm/arch-exynos/clk.h | 4 + arch/arm/include/asm/arch-exynos/clock.h | 29 +++++ arch/arm/include/asm/arch-exynos/cpu.h | 18 +++ arch/arm/include/asm/arch-exynos/gpio.h | 19 +++ arch/arm/include/asm/arch-exynos/i2s-regs.h | 66 ++++++++++ arch/arm/include/asm/arch-exynos/periph.h | 7 ++ arch/arm/include/asm/arch-exynos/sound.h | 44 +++++++ arch/arm/include/asm/arch-exynos/spi.h | 78 ++++++++++++ arch/arm/include/asm/arch-mx25/imx-regs.h | 5 +- arch/arm/include/asm/arch-mx25/sys_proto.h | 3 + arch/arm/include/asm/arch-mx31/imx-regs.h | 27 +--- arch/arm/include/asm/arch-mx35/imx-regs.h | 4 + arch/arm/include/asm/arch-mx35/mmc_host_def.h | 31 +++++ arch/arm/include/asm/arch-mx35/spl.h | 38 ++++++ arch/arm/include/asm/arch-mx35/sys_proto.h | 2 + arch/arm/include/asm/arch-mx5/mx5x_pins.h | 6 +- arch/arm/include/asm/arch-mx5/sys_proto.h | 10 +- arch/arm/include/asm/arch-mx6/imx-regs.h | 2 + arch/arm/include/asm/arch-mx6/mx6dl_pins.h | 149 ++++++++++++++++++++++ arch/arm/include/asm/arch-mx6/sys_proto.h | 10 +- arch/arm/include/asm/arch-mxs/imx-regs.h | 7 +- arch/arm/include/asm/arch-mxs/regs-clkctrl-mx28.h | 6 +- arch/arm/include/asm/arch-mxs/{regs-power.h => regs-power-mx28.h} | 4 +- arch/arm/include/asm/arch-s5pc1xx/gpio.h | 7 +- arch/arm/include/asm/arch-tegra20/dc.h | 545 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ arch/arm/include/asm/arch-tegra20/display.h | 152 ++++++++++++++++++++++ arch/arm/include/asm/arch-tegra20/pinmux.h | 4 +- arch/arm/include/asm/arch-tegra20/pwm.h | 75 +++++++++++ arch/arm/include/asm/system.h | 31 +++++ arch/arm/lib/cache-cp15.c | 51 ++++++-- board/compal/paz00/paz00.c | 5 +- board/compulab/dts/tegra20-trimslice.dts | 3 +- board/compulab/trimslice/trimslice.c | 8 ++ board/freescale/mx25pdk/mx25pdk.c | 121 ++++++++++++++++++ board/freescale/mx31ads/u-boot.lds | 2 + board/freescale/mx35pdk/lowlevel_init.S | 4 + board/freescale/mx35pdk/mx35pdk.c | 21 ++++ board/freescale/mx53loco/mx53loco.c | 2 +- board/nvidia/common/board.c | 24 ++++ board/nvidia/dts/tegra20-seaboard.dts | 33 +++++ board/nvidia/harmony/harmony.c | 5 +- board/nvidia/seaboard/seaboard.c | 5 +- board/samsung/smdk5250/Makefile | 2 +- board/samsung/smdk5250/smdk5250.c | 15 +++ board/samsung/smdk5250/{mmc_boot.c => spl_boot.c} | 31 ++++- board/samsung/trats/trats.c | 80 ++++-------- board/samsung/universal_c210/Makefile | 1 - board/samsung/universal_c210/lowlevel_init.S | 395 --------------------------------------------------------- board/samsung/universal_c210/universal.c | 337 ++++++++++++++++++++++++++++++++++++++----------- board/syteco/zmx25/zmx25.c | 1 + board/woodburn/Makefile | 43 +++++++ board/woodburn/imximage.cfg | 4 + board/woodburn/lowlevel_init.S | 38 ++++++ board/woodburn/woodburn.c | 264 +++++++++++++++++++++++++++++++++++++++ boards.cfg | 2 + common/Makefile | 1 + common/cmd_sound.c | 96 ++++++++++++++ common/lcd.c | 89 ++++++++++--- common/main.c | 12 +- doc/README.imx5 | 5 + doc/device-tree-bindings/pwm/tegra20-pwm.txt | 18 +++ doc/device-tree-bindings/video/displaymode.txt | 42 +++++++ doc/device-tree-bindings/video/tegra20-dc.txt | 85 +++++++++++++ drivers/gpio/mxc_gpio.c | 6 +- drivers/gpio/s5p_gpio.c | 6 +- drivers/input/tegra-kbc.c | 18 ++- drivers/mmc/tegra_mmc.c | 7 +- drivers/power/pmic/Makefile | 1 + drivers/power/pmic/pmic_max77686.c | 48 +++++++ drivers/power/power_fsl.c | 8 +- drivers/serial/s3c64xx.c | 3 +- drivers/sound/Makefile | 48 +++++++ drivers/sound/samsung-i2s.c | 358 ++++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/sound/sound.c | 228 +++++++++++++++++++++++++++++++++ drivers/sound/wm8994.c | 792 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/sound/wm8994.h | 87 +++++++++++++ drivers/sound/wm8994_registers.h | 299 ++++++++++++++++++++++++++++++++++++++++++++ drivers/spi/Makefile | 1 + drivers/spi/exynos_spi.c | 367 +++++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/spi/mxc_spi.c | 9 +- drivers/usb/host/ehci-mx5.c | 146 ++++++++++++++++++---- drivers/usb/host/ehci-mx6.c | 5 + drivers/usb/host/ehci-mxc.c | 225 +++++++++++++++++++++++++-------- drivers/video/Makefile | 2 + drivers/video/exynos_fb.c | 15 ++- drivers/video/ipu_regs.h | 2 +- drivers/video/ld9040.c | 144 +++++++++++++++++++++ drivers/video/tegra.c | 379 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/watchdog/Makefile | 1 + arch/arm/cpu/armv7/s5p-common/wdt.c => drivers/watchdog/s5p_wdt.c | 0 include/configs/harmony.h | 4 +- include/configs/mx25pdk.h | 43 ++++++- include/configs/mx28evk.h | 2 +- include/configs/mx31pdk.h | 2 +- include/configs/mx35pdk.h | 18 ++- include/configs/mx51_efikamx.h | 1 + include/configs/mx51evk.h | 5 +- include/configs/mx53evk.h | 1 + include/configs/mx53loco.h | 4 +- include/configs/mx6qarm2.h | 1 + include/configs/mx6qsabre_common.h | 4 +- include/configs/mx6qsabrelite.h | 3 +- include/configs/palmld.h | 3 + include/configs/palmtc.h | 3 + include/configs/paz00.h | 3 + include/configs/s5pc210_universal.h | 36 ++++++ include/configs/seaboard.h | 16 ++- include/configs/smdk5250.h | 74 ++++++++++- include/configs/tec.h | 1 - include/configs/tegra-common-post.h | 43 +++---- include/configs/tegra20-common.h | 3 + include/configs/trats.h | 17 ++- include/configs/trimslice.h | 4 + include/configs/ventana.h | 3 + include/configs/vision2.h | 1 + include/configs/whistler.h | 3 + include/configs/woodburn.h | 34 +++++ include/configs/woodburn_common.h | 313 ++++++++++++++++++++++++++++++++++++++++++++++ include/configs/woodburn_sd.h | 60 +++++++++ include/configs/zipitz2.h | 3 + include/configs/zmx25.h | 6 +- include/fdtdec.h | 2 + include/i2s.h | 127 +++++++++++++++++++ include/lcd.h | 11 ++ include/ld9040.h | 32 +++++ include/mc34704.h | 49 ++++++++ include/power/max77686_pmic.h | 158 +++++++++++++++++++++++ include/power/max8998_pmic.h | 2 + include/sound.h | 62 +++++++++ include/usb/ehci-fsl.h | 28 ++++- lib/fdtdec.c | 2 + nand_spl/board/freescale/mx31pdk/u-boot.lds | 2 + spl/Makefile | 6 + 163 files changed, 8451 insertions(+), 1094 deletions(-) create mode 100644 arch/arm/cpu/arm1136/mx35/mx35_sdram.c create mode 100644 arch/arm/cpu/arm1136/u-boot-spl.lds create mode 100644 arch/arm/cpu/arm1176/s3c64xx/init.c create mode 100644 arch/arm/cpu/armv7/tegra20/display.c create mode 100644 arch/arm/cpu/armv7/tegra20/pwm.c create mode 100644 arch/arm/include/asm/arch-exynos/i2s-regs.h create mode 100644 arch/arm/include/asm/arch-exynos/sound.h create mode 100644 arch/arm/include/asm/arch-exynos/spi.h create mode 100644 arch/arm/include/asm/arch-mx35/mmc_host_def.h create mode 100644 arch/arm/include/asm/arch-mx35/spl.h create mode 100644 arch/arm/include/asm/arch-mx6/mx6dl_pins.h rename arch/arm/include/asm/arch-mxs/{regs-power.h => regs-power-mx28.h} (99%) create mode 100644 arch/arm/include/asm/arch-tegra20/dc.h create mode 100644 arch/arm/include/asm/arch-tegra20/display.h create mode 100644 arch/arm/include/asm/arch-tegra20/pwm.h rename board/samsung/smdk5250/{mmc_boot.c => spl_boot.c} (66%) delete mode 100644 board/samsung/universal_c210/lowlevel_init.S create mode 100644 board/woodburn/Makefile create mode 100644 board/woodburn/imximage.cfg create mode 100644 board/woodburn/lowlevel_init.S create mode 100644 board/woodburn/woodburn.c create mode 100644 common/cmd_sound.c create mode 100644 doc/device-tree-bindings/pwm/tegra20-pwm.txt create mode 100644 doc/device-tree-bindings/video/displaymode.txt create mode 100644 doc/device-tree-bindings/video/tegra20-dc.txt create mode 100644 drivers/power/pmic/pmic_max77686.c create mode 100644 drivers/sound/Makefile create mode 100644 drivers/sound/samsung-i2s.c create mode 100644 drivers/sound/sound.c create mode 100644 drivers/sound/wm8994.c create mode 100644 drivers/sound/wm8994.h create mode 100644 drivers/sound/wm8994_registers.h create mode 100644 drivers/spi/exynos_spi.c create mode 100644 drivers/video/ld9040.c create mode 100644 drivers/video/tegra.c rename arch/arm/cpu/armv7/s5p-common/wdt.c => drivers/watchdog/s5p_wdt.c (100%) create mode 100644 include/configs/woodburn.h create mode 100644 include/configs/woodburn_common.h create mode 100644 include/configs/woodburn_sd.h create mode 100644 include/i2s.h create mode 100644 include/ld9040.h create mode 100644 include/mc34704.h create mode 100644 include/power/max77686_pmic.h create mode 100644 include/sound.h Amicalement, -- Albert.

4 3

[U-Boot] [RFC][PULL-REQ] MTD update
by Sergey Lapin 03 Jan '13

03 Jan '13

Hi, all! As I failed to submit 250KB patch to the list I will send this pull request This patch is not for inclusion yet. This patch is just update of u-boot MTD with Linux kernel's MTD v3.8-rc. The following changes since commit f8cfcf1b1c7543d5dd103359376a3319301143bc: env: don't generate callback list entries for SPL (2012-12-22 05:57:16 -0700) are available in the git repository at: git://github.com/slapin/uboot-allwinner.git upstream-mtd Sergey Lapin (1): MTD resync from Linux-3.8-rc2+ (master) common/cmd_nand.c | 18 +- drivers/mtd/Makefile | 4 +- drivers/mtd/mtdcore.c | 372 +++++++ drivers/mtd/nand/nand_base.c | 2274 ++++++++++++++++++++++++----------------- drivers/mtd/nand/nand_bbt.c | 839 ++++++++-------- drivers/mtd/nand/nand_ids.c | 21 +- drivers/mtd/nand/nand_util.c | 19 +- include/linux/mtd/bbm.h | 119 ++- include/linux/mtd/flashchip.h | 58 ++ include/linux/mtd/mtd-abi.h | 189 +++- include/linux/mtd/mtd.h | 372 +++++--- include/linux/mtd/nand.h | 246 +++-- include/linux/types.h | 2 + include/nand.h | 11 +- 14 files changed, 2848 insertions(+), 1696 deletions(-) create mode 100644 include/linux/mtd/flashchip.h

6 15

[U-Boot] [PATCH] spl:falcon:trats Update Trats default board configuration file to support FALCON MODE
by Lukasz Majewski 03 Jan '13

03 Jan '13

Support for a new command (defined at envs) - spl_export generates the ATAGS image necessary for fast boot. Afterwards, it is stored at ext4 partition. Generated image format: CRC [4B] SIZE [4B] PAYLOAD(ATAGS/DT) [SIZE] Remarks: - CRC is calculated only for PAYLOAD - SIZE is the size of PAYLOAD It is important to adjust ${splsize} when large image is generated. It is defined as hex, since ext4 related commands expect it. The ${spladdr} environment variable corresponds to CONFIG_SYS_SPL_ARGS_ADDR Additionally definitions for DFU have been refactored and support for EFI has been added as well. Signed-off-by: Lukasz Majewski <l.majewski(a)samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park(a)samsung.com> Cc: Minkyu Kang <mk7.kang(a)samsung.com> --- board/samsung/trats/trats.c | 2 +- include/configs/trats.h | 45 +++++++++++++++++++++++++++++++++--------- 2 files changed, 36 insertions(+), 11 deletions(-) diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c index e540190..4738043 100644 --- a/board/samsung/trats/trats.c +++ b/board/samsung/trats/trats.c @@ -66,7 +66,7 @@ struct s3c_plat_otg_data s5pc210_otg_data; int board_init(void) { - gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; + gd->bd->bi_boot_params = CONFIG_SYS_SPL_ARGS_ADDR; check_hw_revision(); printf("HW Revision:\t0x%x\n", board_rev); diff --git a/include/configs/trats.h b/include/configs/trats.h index 355029e..52fe77d 100644 --- a/include/configs/trats.h +++ b/include/configs/trats.h @@ -98,6 +98,7 @@ #undef CONFIG_CMD_MTDPARTS #define CONFIG_CMD_MMC #define CONFIG_CMD_DFU +#define CONFIG_CMD_SETEXPR /* FAT */ #define CONFIG_CMD_FAT @@ -123,9 +124,8 @@ #define CONFIG_ENV_COMMON_BOOT "${console} ${meminfo}" #define CONFIG_DFU_ALT \ - "dfu_alt_info=" \ "u-boot mmc 80 400;" \ - "uImage fat 0 2\0" \ + "uImage ext4 0 2\0" \ #define CONFIG_ENV_OVERWRITE #define CONFIG_SYS_CONSOLE_INFO_QUIET @@ -144,20 +144,20 @@ "mmc read 0 0x42100000 0x80 0x200; run updatebackup\0" \ "lpj=lpj=3981312\0" \ "nfsboot=" \ - "set bootargs root=/dev/nfs rw " \ + "setenv bootargs root=/dev/nfs rw " \ "nfsroot=${nfsroot},nolock,tcp " \ "ip=${ipaddr}:${serverip}:${gatewayip}:" \ "${netmask}:generic:usb0:off " CONFIG_ENV_COMMON_BOOT \ "; run bootk\0" \ "ramfsboot=" \ - "set bootargs root=/dev/ram0 rw rootfstype=ext2 " \ + "setenv bootargs root=/dev/ram0 rw rootfstype=ext2 " \ "${console} ${meminfo} " \ "initrd=0x43000000,8M ramdisk=8192\0" \ "mmcboot=" \ - "set bootargs root=/dev/mmcblk${mmcdev}p${mmcrootpart} " \ + "setenv bootargs root=/dev/mmcblk${mmcdev}p${mmcrootpart} " \ "${lpj} rootwait ${console} ${meminfo} ${opts} ${lcdinfo}; " \ "run loaduimage; bootm 0x40007FC0\0" \ - "bootchart=set opts init=/sbin/bootchartd; run bootcmd\0" \ + "bootchart=setenv opts init=/sbin/bootchartd; run bootcmd\0" \ "boottrace=setenv opts initcall_debug; run bootcmd\0" \ "mmcoops=mmc read 0 0x40000000 0x40 8; md 0x40000000 0x400\0" \ "verify=n\0" \ @@ -166,12 +166,30 @@ "meminfo=crashkernel=32M@0x50000000\0" \ "nfsroot=/nfsroot/arm\0" \ "bootblock=" CONFIG_BOOTBLOCK "\0" \ - "loaduimage=fatload mmc ${mmcdev}:${mmcbootpart} 0x40007FC0 uImage\0" \ + "loaduimage=ext4load mmc ${mmcdev}:${mmcbootpart} 0x40007FC0 uImage\0" \ "mmcdev=0\0" \ "mmcbootpart=2\0" \ - "mmcrootpart=3\0" \ + "mmcrootpart=5\0" \ "opts=always_resume=1\0" \ - CONFIG_DFU_ALT + "dfu_alt_info=" CONFIG_DFU_ALT \ + "spladdr=0x40000100\0" \ + "splsize=0x200\0" \ + "splfile=falcon.bin\0" \ + "spl_export=" \ + "setexpr spl_imgsize ${splsize} + 8 ;" \ + "setexpr spl_imgaddr ${spladdr} - 8 ;" \ + "setexpr spl_addr_tmp ${spladdr} - 4 ;" \ + "mw.b ${spl_imgaddr} 0x00 ${spl_imgsize};run loaduimage;" \ + "setenv bootargs root=/dev/mmcblk${mmcdev}p${mmcrootpart} " \ + "${lpj} rootwait ${console} ${meminfo} ${opts} ${lcdinfo};" \ + "spl export atags 0x40007FC0;" \ + "crc32 ${spladdr} ${splsize} ${spl_imgaddr};" \ + "mw.l ${spl_addr_tmp} ${splsize};" \ + "ext4write mmc ${mmcdev}:${mmcbootpart}" \ + " /${splfile} ${spl_imgaddr} ${spl_imgsize};" \ + "setenv spl_imgsize;" \ + "setenv spl_imgaddr;" \ + "setenv spl_addr_tmp;\0" /* Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ @@ -207,11 +225,18 @@ #define CONFIG_ENV_OFFSET ((32 - 4) << 10) /* 32KiB - 4KiB */ #define CONFIG_DOS_PARTITION +#define CONFIG_EFI_PARTITION + +/* EXT4 */ +#define CONFIG_CMD_EXT4 +#define CONFIG_CMD_EXT4_WRITE +/* Falcon mode definitions */ +#define CONFIG_CMD_SPL +#define CONFIG_SYS_SPL_ARGS_ADDR PHYS_SDRAM_1 + 0x100 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_CACHELINE_SIZE 32 - #define CONFIG_SOFT_I2C #define CONFIG_SOFT_I2C_READ_REPEATED_START #define CONFIG_SYS_I2C_INIT_BOARD -- 1.7.2.3

2 3

[U-Boot] Please pull u-boot-x86.git
by Simon Glass 03 Jan '13

03 Jan '13

Hi Tom, These are the two that patchwork somehow missed. They are in there now, so here is the pull request for those two. The following changes since commit f8cfcf1b1c7543d5dd103359376a3319301143bc: env: don't generate callback list entries for SPL (2012-12-22 05:57:16 -0700) are available in the git repository at: git://git.denx.de/u-boot-x86.git master Simon Glass (1): x86: coreboot: Enable io command Stefan Reinauer (1): x86: Add coreboot version to u-boot's version command common/cmd_version.c | 7 ++++++- include/configs/coreboot.h | 1 + 2 files changed, 7 insertions(+), 1 deletions(-) Regards, Simon

2 1

[U-Boot] [PATCH 1/1] omap4: use plain text env file instead boot scripts
by Javier Martinez Canillas 02 Jan '13

02 Jan '13

Based on commit cf073e49bc3502be1b48a0e3faf0cde9edbb89db for beagleboard Using the new env import command it is possible to use plain text files instead of script-images. Plain text files are much easier to handle. E.g. If your boot.scr contains the following: ----------------------------------- setenv dvimode 1024x768-16@60 run loaduimage run mmcboot ----------------------------------- you could create a file named uEnv.txt and use that instead of boot.scr: ----------------------------------- dvimode=1024x768-16@60 uenvcmd=run loaduimage; run mmcboot ----------------------------------- The variable uenvcmd (if existent) will be executed (using run) after uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence will be started, therefore you could just use ----------------------------------- dvimode=1024x768-16@60 ----------------------------------- as uEnv.txt because loaduimage and mmcboot is part of the default boot sequence Signed-off-by: Javier Martinez Canillas <javier.martinez(a)collabora.co.uk> --- include/configs/omap4_common.h | 22 +++++++++++++--------- 1 files changed, 13 insertions(+), 9 deletions(-) diff --git a/include/configs/omap4_common.h b/include/configs/omap4_common.h index a32369a..a821c01 100644 --- a/include/configs/omap4_common.h +++ b/include/configs/omap4_common.h @@ -156,9 +156,9 @@ "vram=${vram} " \ "root=${mmcroot} " \ "rootfstype=${mmcrootfstype}\0" \ - "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ - "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \ - "source ${loadaddr}\0" \ + "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} uEnv.txt\0" \ + "importbootenv=echo Importing environment from mmc${mmcdev} ...; " \ + "env import -t ${loadaddr} ${filesize}\0" \ "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ "mmcboot=echo Booting from mmc${mmcdev} ...; " \ "run mmcargs; " \ @@ -166,12 +166,16 @@ #define CONFIG_BOOTCOMMAND \ "mmc dev ${mmcdev}; if mmc rescan; then " \ - "if run loadbootscript; then " \ - "run bootscript; " \ - "else " \ - "if run loaduimage; then " \ - "run mmcboot; " \ - "fi; " \ + "echo SD/MMC found on device ${mmcdev};" \ + "if run loadbootenv; then " \ + "run importbootenv; " \ + "fi;" \ + "if test -n ${uenvcmd}; then " \ + "echo Running uenvcmd ...;" \ + "run uenvcmd;" \ + "fi;" \ + "if run loaduimage; then " \ + "run mmcboot; " \ "fi; " \ "fi" -- 1.7.7.6

3 6