March 2012 - U-Boot

[U-Boot] [PATCH] pxe: get ethaddr from the current device instead of env
by Rob Herring 11 Jul '12

11 Jul '12

From: Rob Herring <rob.herring(a)calxeda.com> The env variable "ethaddr" may not be set, so get the address from the eth_device struct instead. This also enables pxe for secondary ethernet devices. Signed-off-by: Rob Herring <rob.herring(a)calxeda.com> --- common/cmd_pxe.c | 31 ++++++++++++------------------- 1 files changed, 12 insertions(+), 19 deletions(-) diff --git a/common/cmd_pxe.c b/common/cmd_pxe.c index 3efd700..f14ef89 100644 --- a/common/cmd_pxe.c +++ b/common/cmd_pxe.c @@ -56,38 +56,31 @@ static char *from_env(char *envvar) */ static int format_mac_pxe(char *outbuf, size_t outbuf_len) { - size_t ethaddr_len; - char *p, *ethaddr; - - ethaddr = from_env("ethaddr"); - - if (!ethaddr) - return -ENOENT; - - ethaddr_len = strlen(ethaddr); + char *p; + struct eth_device *dev; /* * ethaddr_len + 4 gives room for "01-", ethaddr, and a NUL byte at * the end. */ - if (outbuf_len < ethaddr_len + 4) { - printf("outbuf is too small (%d < %d)\n", - outbuf_len, ethaddr_len + 4); - + if (outbuf_len < 21) { + printf("outbuf is too small (%d < 21)\n", outbuf_len); return -EINVAL; } - strcpy(outbuf, "01-"); + eth_set_current(); + dev = eth_get_dev(); + if (!dev) + return -ENODEV; - for (p = outbuf + 3; *ethaddr; ethaddr++, p++) { - if (*ethaddr == ':') + sprintf(outbuf, "01-%pM", dev->enetaddr); + for (p = outbuf + 3; *p; p++) { + if (*p == ':') *p = '-'; else - *p = tolower(*ethaddr); + *p = tolower(*p); } - *p = '\0'; - return 1; } -- 1.7.5.4

4 13

[U-Boot] [PATCH] PXA: Enable CONFIG_PREBOOT on zipitz2
by Marek Vasut 07 Jul '12

07 Jul '12

Signed-off-by: Marek Vasut <marex(a)denx.de> --- include/configs/zipitz2.h | 1 + 1 files changed, 1 insertions(+), 0 deletions(-) diff --git a/include/configs/zipitz2.h b/include/configs/zipitz2.h index 26204af..e14f59a 100644 --- a/include/configs/zipitz2.h +++ b/include/configs/zipitz2.h @@ -32,6 +32,7 @@ #undef CONFIG_BOARD_LATE_INIT #undef CONFIG_USE_IRQ #undef CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_PREBOOT /* * Environment settings -- 1.7.9

2 2

[U-Boot] [PATCH] add new board vl_ma2sc
by Jens Scharsig 07 Jul '12

07 Jul '12

* add support for board VL+MA2SC * adds vl_ma2sc_config for standard NOR boot configuration * adds vl_ma2sc_ram_config for RAM load configuration Signed-off-by: Jens Scharsig <esw(a)bus-elektronik.de> --- MAINTAINERS | 1 + board/BuS/vl_ma2sc/Makefile | 54 ++++ board/BuS/vl_ma2sc/vl_ma2sc.c | 596 +++++++++++++++++++++++++++++++++++++++++ boards.cfg | 2 + include/configs/vl_ma2sc.h | 466 ++++++++++++++++++++++++++++++++ 5 files changed, 1119 insertions(+), 0 deletions(-) create mode 100644 board/BuS/vl_ma2sc/Makefile create mode 100644 board/BuS/vl_ma2sc/vl_ma2sc.c create mode 100644 include/configs/vl_ma2sc.h diff --git a/MAINTAINERS b/MAINTAINERS index a5b728e..12047fc 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -819,6 +819,7 @@ Steve Sakoman <sakoman(a)gmail.com> Jens Scharsig <esw(a)bus-elektronik.de> eb_cpux9k2 ARM920T (AT91RM9200 SoC) + vl_ma2sc ARM926EJS (AT91SAM9263 SoC) Heiko Schocher <hs(a)denx.de> diff --git a/board/BuS/vl_ma2sc/Makefile b/board/BuS/vl_ma2sc/Makefile new file mode 100644 index 0000000..3f36a4d --- /dev/null +++ b/board/BuS/vl_ma2sc/Makefile @@ -0,0 +1,54 @@ +# +# (C) Copyright 2003-2008 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# (C) Copyright 2009-2012 +# Jens Scharsig <esw(a)bus-elekronik.de> +# BuS Elektronik GmbH & Co. KG +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS += vl_ma2sc.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/BuS/vl_ma2sc/vl_ma2sc.c b/board/BuS/vl_ma2sc/vl_ma2sc.c new file mode 100644 index 0000000..dfaf2cb --- /dev/null +++ b/board/BuS/vl_ma2sc/vl_ma2sc.c @@ -0,0 +1,596 @@ +/* + * (C) Copyright 2009-2012 + * Jens Scharsig <esw(a)bus-elekronik.de> + * BuS Elektronik GmbH & Co. KG + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> +#include <common.h> +#include <asm/sizes.h> +#include <asm/io.h> +#include <asm/arch/hardware.h> +#include <asm/arch/clk.h> +#include <asm/arch/at91_matrix.h> +#include <asm/arch/at91sam9_smc.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_pio.h> +#include <asm/arch/at91_rstc.h> +#include <asm/arch/at91sam9263.h> +#include <asm/arch/gpio.h> +#include <asm/arch/at91_common.h> +#include <lcd.h> +#include <i2c.h> +#include <atmel_lcdc.h> +#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB) +#include <net.h> +#endif +#include <netdev.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Miscelaneous platform dependent initialisations + */ + +#ifdef CONFIG_CMD_NAND +static void vl_ma2sc_nand_hw_init(void) +{ + unsigned long csa; + at91_smc_t *smc = (at91_smc_t *) ATMEL_BASE_SMC0; + at91_matrix_t *matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX; + at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; + + at91_set_pio_output(AT91_PIO_PORTA, 13, 1); /* CAN_TX -> H */ + at91_set_pio_output(AT91_PIO_PORTA, 12, 1); /* CAN_STB -> H */ + at91_set_pio_output(AT91_PIO_PORTA, 11, 1); /* CAN_EN -> H */ + + /* Enable CS3 */ + csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A; + writel(csa, &matrix->csa[0]); + + /* Configure SMC CS3 for NAND/SmartMedia */ +#if 1 + writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[3].setup); + + writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | + AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), + &smc->cs[3].pulse); + + writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), + &smc->cs[3].cycle); + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_DBW_8 | + AT91_SMC_MODE_TDF_CYCLE(2), + &smc->cs[3].mode); +#else +#warning SAMSUNG Timmings +#define NTM 1 + writel(AT91_SMC_SETUP_NWE(NTM * 2) | AT91_SMC_SETUP_NCS_WR(NTM * 1) | + AT91_SMC_SETUP_NRD(NTM * 2) | AT91_SMC_SETUP_NCS_RD(NTM * 1), + &smc->cs[3].setup); + + writel(AT91_SMC_PULSE_NWE(NTM * 3) | AT91_SMC_PULSE_NCS_WR(NTM * 5) | + AT91_SMC_PULSE_NRD(NTM * 5) | AT91_SMC_PULSE_NCS_RD(NTM * 7), + &smc->cs[3].pulse); + + writel(AT91_SMC_CYCLE_NWE(NTM * 7) | AT91_SMC_CYCLE_NRD(NTM * 10), + &smc->cs[3].cycle); + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_DBW_8 | + AT91_SMC_MODE_TDF_CYCLE(2), + &smc->cs[3].mode); +#endif + writel((1 << ATMEL_ID_PIOB) | (1 << ATMEL_ID_PIOCDE), + &pmc->pcer); + + /* Configure RDY/BSY */ +#ifdef CONFIG_SYS_NAND_READY_PIN + at91_set_pio_input(CONFIG_SYS_NAND_READY_PIN, 1); +#endif + /* Enable NandFlash */ + at91_set_pio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); +} +#endif + +#ifdef CONFIG_MACB +static void vl_ma2sc_macb_hw_init(void) +{ + unsigned long erstl; + at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; + at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; + at91_rstc_t *rstc = (at91_rstc_t *) ATMEL_BASE_RSTC; + /* Enable clock */ + writel(1 << ATMEL_ID_EMAC, &pmc->pcer); + + /* + * Disable pull-up on: + * RXDV (PC25) => PHY normal mode (not Test mode) + * ERX0 (PE25) => PHY ADDR0 + * ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0 + * + * PHY has internal pull-down + */ + + writel((1 << 25), &pio->pioc.pudr); + writel((1 << 25) | (1 << 26), &pio->pioe.pudr); + + erstl = readl(&rstc->mr) & AT91_RSTC_MR_ERSTL_MASK; + + /* Need to reset PHY -> 500ms reset */ + writel(AT91_RSTC_KEY | AT91_RSTC_MR_ERSTL(0x0D) | + AT91_RSTC_MR_URSTEN, &rstc->mr); + + writel(AT91_RSTC_KEY | AT91_RSTC_CR_EXTRST, &rstc->cr); + /* Wait for end hardware reset */ + while (!(readl(&rstc->sr) & AT91_RSTC_SR_NRSTL)) + ; + + /* Restore NRST value */ + writel(AT91_RSTC_KEY | erstl | AT91_RSTC_MR_URSTEN, &rstc->mr); + + /* Re-enable pull-up */ + writel((1 << 25), &pio->pioc.puer); + writel((1 << 25) | (1 << 26), &pio->pioe.puer); + + at91_macb_hw_init(); +} +#endif + +#ifdef CONFIG_LCD +vidinfo_t panel_info = { + vl_col: 320, + vl_row: 240, + vl_clk: 6500000, + vl_sync: ATMEL_LCDC_INVDVAL_INVERTED | + ATMEL_LCDC_INVLINE_INVERTED | + ATMEL_LCDC_INVVD_INVERTED | + ATMEL_LCDC_INVFRAME_INVERTED, + vl_bpix: (ATMEL_LCDC_PIXELSIZE_8 >> 5), + vl_tft: 1, + vl_hsync_len: 5, /* Horiz Sync Pulse Width */ + vl_left_margin: 68, /* horiz back porch */ + vl_right_margin: 20, /* horiz front porch */ + vl_vsync_len: 2, /* vert Sync Pulse Width */ + vl_upper_margin: 18, /* vert back porch */ + vl_lower_margin: 4, /* vert front porch */ + mmio: ATMEL_BASE_LCDC, +}; + +void lcd_enable(void) +{ +} + +void lcd_disable(void) +{ +} + +static void vl_ma2sc_lcd_hw_init(void) +{ + at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; + + at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* LCDVSYNC */ + at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDHSYNC */ + at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDDOTCK */ + at91_set_a_periph(AT91_PIO_PORTC, 3, 0); /* LCDDEN */ + at91_set_b_periph(AT91_PIO_PORTB, 9, 0); /* LCDCC */ + + at91_set_a_periph(AT91_PIO_PORTC, 4, 0); /* LCDD0 */ + at91_set_a_periph(AT91_PIO_PORTC, 5, 0); /* LCDD1 */ + at91_set_a_periph(AT91_PIO_PORTC, 6, 0); /* LCDD2 */ + at91_set_a_periph(AT91_PIO_PORTC, 7, 0); /* LCDD3 */ + at91_set_a_periph(AT91_PIO_PORTC, 8, 0); /* LCDD4 */ + at91_set_a_periph(AT91_PIO_PORTC, 9, 0); /* LCDD5 */ + at91_set_a_periph(AT91_PIO_PORTC, 10, 0); /* LCDD6 */ + at91_set_a_periph(AT91_PIO_PORTC, 11, 0); /* LCDD7 */ + + at91_set_a_periph(AT91_PIO_PORTC, 13, 0); /* LCDD9 */ + at91_set_a_periph(AT91_PIO_PORTC, 14, 0); /* LCDD10 */ + at91_set_a_periph(AT91_PIO_PORTC, 15, 0); /* LCDD11 */ + at91_set_a_periph(AT91_PIO_PORTC, 16, 0); /* LCDD12 */ + at91_set_b_periph(AT91_PIO_PORTC, 12, 0); /* LCDD13 */ + at91_set_a_periph(AT91_PIO_PORTC, 18, 0); /* LCDD14 */ + at91_set_a_periph(AT91_PIO_PORTC, 19, 0); /* LCDD15 */ + + at91_set_a_periph(AT91_PIO_PORTC, 20, 0); /* LCDD26 */ + at91_set_a_periph(AT91_PIO_PORTC, 21, 0); /* LCDD17 */ + at91_set_a_periph(AT91_PIO_PORTC, 22, 0); /* LCDD18 */ + at91_set_a_periph(AT91_PIO_PORTC, 23, 0); /* LCDD19 */ + at91_set_a_periph(AT91_PIO_PORTC, 24, 0); /* LCDD20 */ + at91_set_b_periph(AT91_PIO_PORTC, 17, 0); /* LCDD21 */ + at91_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDD22 */ + at91_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDD23 */ + + at91_set_pio_output(AT91_PIO_PORTE, 0, 0); /* LCD QXH */ + + at91_set_pio_output(AT91_PIO_PORTE, 2, 0); /* LCD SHUT */ + at91_set_pio_output(AT91_PIO_PORTE, 3, 1); /* LCD TopBottom */ + at91_set_pio_output(AT91_PIO_PORTE, 4, 0); /* LCD REV */ + at91_set_pio_output(AT91_PIO_PORTE, 5, 1); /* LCD RightLeft */ + at91_set_pio_output(AT91_PIO_PORTE, 6, 0); /* LCD Color Mode CM */ + at91_set_pio_output(AT91_PIO_PORTE, 7, 0); /* LCD BGR */ + + at91_set_pio_output(AT91_PIO_PORTB, 9, 0); /* LCD CC */ + + writel(1 << ATMEL_ID_LCDC, &pmc->pcer); + gd->fb_base = ATMEL_BASE_SRAM0; +} + +#endif /* Config LCD */ + +#ifdef CONFIG_BOARD_EARLY_INIT_F +int board_early_init_f(void) +{ + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + + /* Enable clocks for all PIOs */ + writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) | + (1 << ATMEL_ID_PIOCDE), + &pmc->pcer); + + at91_seriald_hw_init(); + + return 0; +} +#endif + +int board_init(void) +{ + at91_smc_t *smc = (at91_smc_t *) ATMEL_BASE_SMC0; + at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; + u32 pin; + + pin = 0x1F000001; + writel(pin, &pio->pioa.idr); + writel(pin, &pio->pioa.pudr); + writel(pin, &pio->pioa.per); + writel(pin, &pio->pioa.oer); + writel(pin, &pio->pioa.sodr); + writel((1 << 25), &pio->pioa.codr); + + pin = 0x1F000100; + writel(pin, &pio->piob.idr); + writel(pin, &pio->piob.pudr); + writel(pin, &pio->piob.per); + writel(pin, &pio->piob.oer); + writel(pin, &pio->piob.codr); + writel((1 << 24), &pio->piob.sodr); + + pin = 0x40000000; /* Pullup DRxD enbable */ + writel(pin, &pio->pioc.puer); + + pin = 0x0000000F; /* HWversion als Input */ + writel(pin, &pio->piod.idr); + writel(pin, &pio->piod.puer); + writel(pin, &pio->piod.per); + writel(pin, &pio->piod.odr); + writel(pin, &pio->piod.owdr); + + /* Enable Ctrlc */ + console_init_f(); + + gd->bd->bi_arch_number = MACH_TYPE_VL_MA2SC; + /* adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + + writel(CONFIG_SYS_SMC0_MODE0_VAL, &smc->cs[0].setup); + writel(CONFIG_SYS_SMC0_CYCLE0_VAL, &smc->cs[0].cycle); + writel(CONFIG_SYS_SMC0_PULSE0_VAL, &smc->cs[0].pulse); + writel(CONFIG_SYS_SMC0_SETUP0_VAL, &smc->cs[0].setup); + +#ifdef CONFIG_CMD_NAND + vl_ma2sc_nand_hw_init(); +#endif +#ifdef CONFIG_MACB + vl_ma2sc_macb_hw_init(); +#endif +#ifdef CONFIG_USB_OHCI_NEW + at91_uhp_hw_init(); +#endif +#ifdef CONFIG_LCD + vl_ma2sc_lcd_hw_init(); +#endif + return 0; +} + +#ifdef CONFIG_MISC_INIT_R + +int misc_init_r(void) +{ + uchar buffer[8]; + at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; + u32 pin; + + buffer[0] = 0x04; + buffer[1] = 0x00; + if (i2c_write(0x68, 0x0E, 1, buffer, 2) != 0) + puts("error reseting rtc clock\n\0"); + + /* HWversion lesen */ + + pin = (readl(&pio->piod.pdsr) & 0x0F) + 0x44; + printf("Board: revision %c\n", pin); + buffer[0] = pin; + buffer[1] = 0; + setenv("revision", (char *) buffer); + + pin = 0x40000000; /* Pullup DRxD enbable */ + writel(pin, &pio->pioc.puer); + return 0; +} +#endif + +int dram_init(void) +{ + gd->ram_size = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, + CONFIG_SYS_SDRAM_SIZE); + return 0; +} + +#ifdef CONFIG_RESET_PHY_R +void reset_phy(void) +{ +#ifdef CONFIG_MACB + /* + * Initialize ethernet HW addr prior to starting Linux, + * needed for nfsroot + */ + eth_init(gd->bd); +#endif +} +#endif + +int board_eth_init(bd_t *bis) +{ + int rc = 0; +#ifdef CONFIG_MACB + rc = macb_eth_initialize(0, (void *) ATMEL_BASE_EMAC, 0x01); +#endif + return rc; +} + +#ifdef CONFIG_SOFT_I2C + +void i2c_init_board(void) +{ + u32 pin; + + at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; + at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; + u8 sda = (1<<4); + u8 scl = (1<<5); + + writel(1 << ATMEL_ID_PIOB, &pmc->pcer); + pin = sda | scl; + writel(pin, &pio->piob.idr); /* Disable Interupt */ + writel(pin, &pio->piob.pudr); + writel(pin, &pio->piob.per); + writel(pin, &pio->piob.oer); + writel(pin, &pio->piob.sodr); +} + +#endif + +void watchdog_reset(void) +{ + at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; + u32 pin = 0x1; /* PA0 */ + + if ((readl(&pio->pioa.odsr) & pin) > 0) + writel(pin, &pio->pioa.codr); + else + writel(pin, &pio->pioa.sodr); +} + +void enable_caches(void) +{ +#ifndef CONFIG_SYS_DCACHE_OFF + dcache_enable(); +#endif +} + +/*---------------------------------------------------------------------------*/ + +int do_ledtest(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + int rcode = 1; + int row; + int col; + u32 pinz; + u32 pins; + at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; + + at91_set_pio_output(AT91_PIO_PORTB, 8, 0); /* LCD DIM */ + + pins = 0x1F000000; + writel(pins, &pio->pioa.idr); + writel(pins, &pio->pioa.pudr); + writel(pins, &pio->pioa.per); + writel(pins, &pio->pioa.oer); + writel(pins, &pio->pioa.sodr); + + pinz = 0x1F000000; + writel(pinz, &pio->piob.idr); + writel(pinz, &pio->piob.pudr); + writel(pinz, &pio->piob.per); + writel(pinz, &pio->piob.oer); + writel(pinz, &pio->piob.sodr); + + for (row = 0; row < 5; row++) { + for (col = 0; col < 5; col++) { + writel((0x01000000 << col), &pio->piob.sodr); + writel((0x01000000 << row), &pio->pioa.codr); + printf("LED Test %d x %d\n", row, col); + udelay(1000000); + writel(pinz, &pio->piob.codr); + writel(pins, &pio->pioa.sodr); + } + } + + return rcode; +} + +void poweroff(void) +{ + watchdog_reset(); + at91_set_pio_output(AT91_PIO_PORTA, 13, 1); /* CAN_TX -> H */ + udelay(100); + at91_set_pio_output(AT91_PIO_PORTA, 12, 0); /* CAN_STB -> L */ + udelay(100); + at91_set_pio_output(AT91_PIO_PORTA, 11, 0); /* CAN_EN -> L */ + udelay(100); + while (1) + watchdog_reset(); +} + +int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + int rcode = 1; + poweroff(); + return rcode; +} + +int do_beep(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + int i; + u32 freq; + u32 durate; + int rcode = 1; + + freq = 1000; + durate = 2; + switch (argc) { + case 3: + durate = simple_strtoul(argv[2], NULL, 10); + case 2: + freq = simple_strtoul(argv[1], NULL, 10); + case 1: + break; + default: + cmd_usage(cmdtp); + rcode = 1; + break; + } + durate = durate * freq; + freq = 500000 / freq; + for (i = 0; i < durate; i++) { + at91_set_pio_output(AT91_PIO_PORTB, 29, 1); /* Sound On*/ + udelay(freq); + at91_set_pio_output(AT91_PIO_PORTB, 29, 0); /* Sound Off*/ + udelay(freq); + } + at91_set_pio_output(AT91_PIO_PORTB, 29, 0); /* Sound Off*/ + return rcode; +} + +int do_keytest(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + int rcode = 1; + int row; + u32 col; + u32 pinz; + u32 pins; + at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; + at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; + + writel((1 << ATMEL_ID_PIOA), &pmc->pcer); + + pins = 0x001F0000; + writel(pins, &pio->pioa.idr); + writel(pins, &pio->pioa.pudr); + writel(pins, &pio->pioa.per); + writel(pins, &pio->pioa.odr); + + pinz = 0x000F0000; + writel(pinz, &pio->piob.idr); + writel(pinz, &pio->piob.pudr); + writel(pinz, &pio->piob.per); + writel(pinz, &pio->piob.oer); + writel(pinz, &pio->piob.codr); + + while (1) { + col = 0; + for (row = 0; row < 4; row++) { + writel((0x00010000 << row), &pio->piob.sodr); + udelay(10000); + col <<= 4; + col |= ((readl(&pio->pioa.pdsr) >> 16) & 0xF) ^ 0xF ; + writel(pinz, &pio->piob.codr); + } + printf("Matix: "); + for (row = 0; row < 16; row++) { + printf("%1.1d", col & 1); + col >>= 1; + } + printf(" SP %d\r ", + 1 ^ (1 & (readl(&pio->piob.pdsr) >> 20))); + if ((1 & (readl(&pio->pioa.pdsr) >> 1)) == 0) { + /* SHUTDOWN */ + row = 0; + while (row < 1000) { + if ((1 & (readl(&pio->pioa.pdsr) >> 1)) == 0) + row++; + udelay(100); + } + udelay(100000); + row = 0; + while (row < 1000) { + if ((1 & (readl(&pio->pioa.pdsr) >> 1)) > 0) { + row++; + udelay(1000); + } + } + poweroff(); + while (1) + ; + } + } + return rcode; +} + +/*****************************************************************************/ + +U_BOOT_CMD( + ledtest, 1, 0, do_ledtest, + "test ledmatrix", + "\n" + ); + +U_BOOT_CMD( + keytest, 1, 0, do_keytest, + "test keymatix and special keys, poweroff on pressing ON key", + "\n" + ); + +U_BOOT_CMD( + poweroff, 1, 0, do_poweroff, + "power off", + "\n" + ); + +U_BOOT_CMD( + beep, 3, 0, do_beep, + "[freq [duration]]", + "freq frequence of beep\nduration duration of beep\n" + ); + +/*****************************************************************************/ diff --git a/boards.cfg b/boards.cfg index 576b392..2f7211f 100644 --- a/boards.cfg +++ b/boards.cfg @@ -94,6 +94,8 @@ at91sam9xeek_dataflash_cs1 arm arm926ejs at91sam9260ek atmel at91sam9xeek_nandflash arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9XE,SYS_USE_NANDFLASH snapper9260 arm arm926ejs - bluewater at91 snapper9260:AT91SAM9260 snapper9g20 arm arm926ejs snapper9260 bluewater at91 snapper9260:AT91SAM9G20 +vl_ma2sc arm arm926ejs vl_ma2sc BuS at91 +vl_ma2sc_ram arm arm926ejs vl_ma2sc BuS at91 vl_ma2sc:RAMLOAD sbc35_a9g20_eeprom arm arm926ejs sbc35_a9g20 calao at91 sbc35_a9g20:AT91SAM9G20,SYS_USE_EEPROM sbc35_a9g20_nandflash arm arm926ejs sbc35_a9g20 calao at91 sbc35_a9g20:AT91SAM9G20,SYS_USE_NANDFLASH tny_a9260_eeprom arm arm926ejs tny_a9260 calao at91 tny_a9260:AT91SAM9260,SYS_USE_EEPROM diff --git a/include/configs/vl_ma2sc.h b/include/configs/vl_ma2sc.h new file mode 100644 index 0000000..d9c2a2d --- /dev/null +++ b/include/configs/vl_ma2sc.h @@ -0,0 +1,466 @@ +/* + * (C) Copyright 2009-2012 + * Jens Scharsig <esw(a)bus-elekronik.de> + * BuS Elektronik GmbH & Co. KG + * + * Configuation settings for the VL_MA2SC board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*--------------------------------------------------------------------------*/ + +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ +#define CONFIG_ARM926EJS /* This is an ARM926EJS Core */ +#define CONFIG_AT91FAMILY +#define CONFIG_AT91SAM9263 /* It's an Atmel AT91SAM9263 SoC*/ +#define CONFIG_VL_MA2SC /* on an VL_MA2SC Board */ +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_MISC_INIT_R + +#include <asm/hardware.h> + +#define MACH_TYPE_VL_MA2SC 2412 +#define CONFIG_MACH_TYPE MACH_TYPE_VL_MA2SC + +#define CONFIG_SYS_DCACHE_OFF + +#ifdef CONFIG_RAMLOAD +#define CONFIG_SYS_TEXT_BASE 0x21000000 +#else +#define CONFIG_SYS_TEXT_BASE 0x00000000 +#endif +#define CONFIG_SYS_LOAD_ADDR 0x21000000 /* default load address */ + +#define CONFIG_IDENT_STRING " on MiS Activ 2" +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AT91_GPIO + +#if !defined(CONFIG_SYS_USE_NANDFLASH) && !defined(CONFIG_RAMLOAD) +#define CONFIG_SYS_USE_NORFLASH +#define CONFIG_SYS_USE_BOOT_NORFLASH +#endif + +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG + +#ifndef CONFIG_SYS_USE_BOOT_NORFLASH +#define CONFIG_SKIP_LOWLEVEL_INIT +#endif + +/* + * Hardware drivers + */ + +#define CONFIG_BOARD_EARLY_INIT_F + +#define CONFIG_WATCHDOG + +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_SYS + +/* LCD */ +#define CONFIG_LCD +#define CONFIG_ATMEL_LCD +#define CONFIG_SPLASH_SCREEN +#define CONFIG_SYS_BLACK_ON_WHITE +#define LCD_BPP LCD_COLOR8 +#define CONFIG_ATMEL_LCD_BGR555 + +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_BOOTDELAY 3 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_LOADS + +#define CONFIG_CMD_BMP +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_I2C +#define CONFIG_CMD_NAND +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_MD5SUM +#define CONFIG_CMD_SHA1SUM +/* +#define CONFIG_CMD_SPI +*/ +#define CONFIG_CMD_FAT +#define CONFIG_CMD_USB + +#define CONFIG_SYS_LONGHELP +#define CONFIG_MD5 +#define CONFIG_SHA1 + +/*---------------------------------------------------------------------------- + * Hardware confuguration + *---------------------------------------------------------------------------*/ + +/* USB */ +#define CONFIG_USB_ATMEL +#define CONFIG_USB_OHCI_NEW +#define CONFIG_DOS_PARTITION +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000 /* UHP_BASE */ +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 +#define CONFIG_USB_STORAGE +#define CONFIG_AT91C_PQFP_UHPBUG + +/* I2C-Bus */ + +#define CONFIG_SYS_I2C_SPEED 50000 +#define CONFIG_SYS_I2C_SLAVE 0 /* not used */ + +#ifndef CONFIG_HARD_I2C +#define CONFIG_SOFT_I2C + +/* Software I2C driver configuration */ + +#define I2C_DELAY udelay(2500000/CONFIG_SYS_I2C_SPEED) + +#define AT91_PIN_SDA (1<<4) /* AT91C_PIO_PB4 */ +#define AT91_PIN_SCL (1<<5) /* AT91C_PIO_PB5 */ + +#define I2C_INIT i2c_init_board(); +#define I2C_ACTIVE writel(AT91_PIN_SDA, &pio->piob.mddr); +#define I2C_TRISTATE writel(AT91_PIN_SDA, &pio->piob.mder); +#define I2C_READ ((readl(&pio->piob.pdsr) & AT91_PIN_SDA) != 0) +#define I2C_SDA(bit) \ + do { \ + if (bit) \ + writel(AT91_PIN_SDA, &pio->piob.sodr); \ + else \ + writel(AT91_PIN_SDA, &pio->piob.codr); \ + } while (0); +#define I2C_SCL(bit) \ + do { \ + if (bit) \ + writel(AT91_PIN_SCL, &pio->piob.sodr); \ + else \ + writel(AT91_PIN_SCL, &pio->piob.codr); \ + } while (0); +#endif + +/* I2C-RTC */ + +#ifdef CONFIG_CMD_DATE +#define CONFIG_RTC_DS1338 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#endif + +/* EEPROM */ + +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 + +/* define PDC[31:16] as DATA[31:16] */ +#define CONFIG_SYS_PIOD_PDR_VAL1 0xFFFF0000 +#define CONFIG_SYS_PIOD_PPUDR_VAL 0xFFFF0000 + +/* EBI0_CSA, CS1 SDRAM, CS3 NAND Flash, 3.3V memories */ +#define CONFIG_SYS_MATRIX_EBI0CSA_VAL \ + (AT91_MATRIX_CSA_DBPUC | AT91_MATRIX_CSA_VDDIOMSEL_3_3V | \ + AT91_MATRIX_CSA_EBI_CS1A) + +/* user reset enable */ +#define CONFIG_SYS_RSTC_RMR_VAL \ + (AT91_RSTC_KEY | \ + AT91_RSTC_MR_URSTEN | \ + AT91_RSTC_MR_ERSTL(15)) + +/* Disable Watchdog */ +#define CONFIG_SYS_WDTC_WDMR_VAL \ + (AT91_WDT_MR_WDIDLEHLT | AT91_WDT_MR_WDDBGHLT | \ + AT91_WDT_MR_WDV(0xFFF) | \ + AT91_WDT_MR_WDDIS | \ + AT91_WDT_MR_WDD(0xFFF)) + +/* clocks */ + +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock */ + +#define MHZ180 +#if defined(MHZ199) +/* 199,8994 MHZ */ +#define MASTER_PLL_MUL 911 +#define MASTER_PLL_DIV 56 +#define MASTER_PLL_OUT 2 +#elif defined(MHZ180) +/* 180 MHZ */ +#define MASTER_PLL_MUL 1875 +#define MASTER_PLL_DIV 128 +#define MASTER_PLL_OUT 2 +#elif defined(MHZTEST) +/* Test MHZ */ +#define CONFIG_DISPLAY_CPUINFO +#define MASTER_PLL_MUL 8 +#define MASTER_PLL_DIV 1 +#define MASTER_PLL_OUT 2 +#else +/* 176.9472 MHZ */ +#define MASTER_PLL_MUL 72 +#define MASTER_PLL_DIV 5 +#define MASTER_PLL_OUT 2 +#endif + +#define CONFIG_SYS_MOR_VAL \ + (AT91_PMC_MOR_MOSCEN | AT91_PMC_MOR_OSCOUNT(255)) + +#define CONFIG_SYS_PLLAR_VAL \ + (AT91_PMC_PLLAR_29 | \ + AT91_PMC_PLLXR_OUT(MASTER_PLL_OUT) | \ + AT91_PMC_PLLXR_PLLCOUNT(63) | \ + AT91_PMC_PLLXR_MUL(MASTER_PLL_MUL - 1) | \ + AT91_PMC_PLLXR_DIV(MASTER_PLL_DIV)) + +/* PCK/2 = MCK Master Clock from PLLA */ +#define CONFIG_SYS_MCKR1_VAL \ + (AT91_PMC_MCKR_CSS_SLOW | AT91_PMC_MCKR_PRES_1 | \ + AT91_PMC_MCKR_MDIV_2) + +/* PCK/2 = MCK Master Clock from PLLA */ +#define CONFIG_SYS_MCKR2_VAL \ + (AT91_PMC_MCKR_CSS_PLLA | AT91_PMC_MCKR_PRES_1 | \ + AT91_PMC_MCKR_MDIV_2) + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE 0x20000000 +#define CONFIG_SYS_SDRAM_SIZE 0x04000000 /* 64 megs */ +#define CONFIG_SYS_INIT_SP_ADDR 0x00504000 /* use internal SRAM0 */ + +#define CONFIG_SYS_SDRC_MR_VAL1 0 +#define CONFIG_SYS_SDRC_TR_VAL1 700 +#define CONFIG_SYS_SDRC_CR_VAL \ + (AT91_SDRAMC_NC_9 | \ + AT91_SDRAMC_NR_13 | \ + AT91_SDRAMC_NB_4 | \ + AT91_SDRAMC_CAS_3 | \ + AT91_SDRAMC_DBW_32 | \ + (2 << 8) | /* Write Recovery Delay */ \ + (7 << 12) | /* Row Cycle Delay */ \ + (2 << 16) | /* Row Precharge Delay */ \ + (2 << 20) | /* Row to Column Delay */ \ + (5 << 24) | /* Active to Precharge Delay */ \ + (8 << 28)) /* Exit Self Refresh to Active Delay */ + +#define CONFIG_SYS_SDRC_MDR_VAL AT91_SDRAMC_MD_SDRAM +#define CONFIG_SYS_SDRC_MR_VAL2 AT91_SDRAMC_MODE_PRECHARGE +#define CONFIG_SYS_SDRAM_VAL1 0 /* SDRAM_BASE */ +#define CONFIG_SYS_SDRC_MR_VAL3 AT91_SDRAMC_MODE_REFRESH +#define CONFIG_SYS_SDRAM_VAL2 0 /* SDRAM_BASE */ +#define CONFIG_SYS_SDRAM_VAL3 0 /* SDRAM_BASE */ +#define CONFIG_SYS_SDRAM_VAL4 0 /* SDRAM_BASE */ +#define CONFIG_SYS_SDRAM_VAL5 0 /* SDRAM_BASE */ +#define CONFIG_SYS_SDRAM_VAL6 0 /* SDRAM_BASE */ +#define CONFIG_SYS_SDRAM_VAL7 0 /* SDRAM_BASE */ +#define CONFIG_SYS_SDRAM_VAL8 0 /* SDRAM_BASE */ +#define CONFIG_SYS_SDRAM_VAL9 0 /* SDRAM_BASE */ +#define CONFIG_SYS_SDRC_MR_VAL4 AT91_SDRAMC_MODE_LMR +#define CONFIG_SYS_SDRAM_VAL10 0 /* SDRAM_BASE */ +#define CONFIG_SYS_SDRC_MR_VAL5 AT91_SDRAMC_MODE_NORMAL +#define CONFIG_SYS_SDRAM_VAL11 0 /* SDRAM_BASE */ +#define CONFIG_SYS_SDRC_TR_VAL2 1200 /* SDRAM_TR */ +#define CONFIG_SYS_SDRAM_VAL12 0 /* SDRAM_BASE */ + +/* NOR flash */ + +#define CONFIG_FLASH_SHOW_PROGRESS 45 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER +#define PHYS_FLASH_1 0x10000000 +#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 +#define CONFIG_SYS_MAX_FLASH_SECT 256 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 + +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000) + +/* setup SMC0, CS0 (NOR Flash) - 16-bit, 15 WS */ +#define CONFIG_SYS_SMC0_SETUP0_VAL \ + (AT91_SMC_SETUP_NWE(10) | AT91_SMC_SETUP_NCS_WR(10) | \ + AT91_SMC_SETUP_NRD(10) | AT91_SMC_SETUP_NCS_RD(10)) +#define CONFIG_SYS_SMC0_PULSE0_VAL \ + (AT91_SMC_PULSE_NWE(11) | AT91_SMC_PULSE_NCS_WR(11) | \ + AT91_SMC_PULSE_NRD(11) | AT91_SMC_PULSE_NCS_RD(11)) +#define CONFIG_SYS_SMC0_CYCLE0_VAL \ + (AT91_SMC_CYCLE_NWE(22) | AT91_SMC_CYCLE_NRD(22)) +#define CONFIG_SYS_SMC0_MODE0_VAL \ + (AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | \ + AT91_SMC_MODE_DBW_16 | \ + AT91_SMC_MODE_TDF | AT91_SMC_MODE_TDF_CYCLE(6)) + +/* NAND flash */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE 0x40000000 +#define CONFIG_SYS_NAND_DBW_8 1 +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* our ALE is AD21 */ +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) /* our CLE is AD22 */ +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTD, 15 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTB, 0 +#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ +#endif + +/* Ethernet */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_NET_MULTI +#define CONFIG_NET_RETRY_COUNT 5 + +#define CONFIG_ETHADDR 00:4D:41:02:52:43 /* MA2SC */ +#define CONFIG_OVERWRITE_ETHADDR_ONCE + +#define CONFIG_SYS_LOAD_ADDR 0x21000000 /* default load address */ + +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END 0x21e00000 + +/* Address and size of Primary Environment Sector */ +#ifdef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_SIZE 0x20000 +#else +#define CONFIG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {312500, 230400, 115200, 19200, \ + 38400, 57600, 9600 } + +#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_CMDLINE_EDITING +#define CONFIG_AUTO_COMPLETE + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN \ + ROUND(3 * CONFIG_ENV_SIZE + 128 * 1024, 0x1000) +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* 128 bytes for initial data */ + +#define CONFIG_STACKSIZE (32*1024) /* regular stack */ + +#ifndef CONFIG_RAMLOAD +#define CONFIG_BOOTCOMMAND "run nfsboot" +#endif +#define CONFIG_BOOT_RETRY_TIME -1 +#define CONFIG_BOOT_RETRY_MIN 15 + +#define CONFIG_NFSBOOTCOMMAND \ + "dhcp $(copy_addr) $(kernelname);" \ + "run bootargsdefaults;" \ + "set bootargs $(bootargs) boot=nfs " \ + ";echo $(bootargs)" \ + ";bootm" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "ubootaddr=10000000\0" \ + "splashimage=10080000\0" \ + "kerneladdr=100A0000\0" \ + "kernelsize=00800000\0" \ + "minifsaddr=108A0000\0" \ + "minifssize=00060000\0" \ + "rootfsaddr=10900000\0" \ + "copy_addr=20200000\0" \ + "rootfssize=01700000\0" \ + "kernelname=uImage_vl_ma2sc\0" \ + "bootargsdefaults=set bootargs " \ + "console=ttyS0,115200 " \ + "video=atmel_lcdfb " \ + "mem=62M " \ + "panic=10 " \ + "boardrevison=\\\"${revision}\\\" " \ + "uboot=\\\"${ver}\\\" " \ + "\0" \ + "update_all=run update_kernel;run update_root;" \ + "run update_splash; run update_uboot\0" \ + "update_kernel=protect off $(kerneladdr) +$(kernelsize);" \ + "dhcp $(copy_addr) $(kernelname);" \ + "erase $(kerneladdr) +$(kernelsize);" \ + "cp.b $(fileaddr) $(kerneladdr) $(filesize);" \ + "protect on $(kerneladdr) +$(kernelsize)" \ + "\0" \ + "update_root=protect off $(rootfsaddr) +$(rootfssize);" \ + "dhcp $(copy_addr) vl_ma2sc.root;" \ + "erase $(rootfsaddr) +$(rootfssize);" \ + "cp.b $(fileaddr) $(rootfsaddr) $(filesize);" \ + "\0" \ + "update_splash=protect off $(splashimage) +20000;" \ + "dhcp $(copy_addr) splash_vl_ma2sc.bmp;" \ + "erase $(splashimage) +20000;" \ + "cp.b $(fileaddr) 10080000 $(filesize);" \ + "protect on $(splashimage) +20000\0" \ + "update_uboot=protect off 10000000 1005FFFF;" \ + "dhcp $(copy_addr) u-boot_vl_ma2sc;" \ + "erase 10000000 1005FFFF;" \ + "cp.b $(fileaddr) $(ubootaddr) $(filesize);" \ + "protect on 10000000 1005FFFF;reset\0" \ + "emergency=run bootargsdefaults;" \ + "set bootargs $(bootargs) root=initramfs boot=emergency " \ + ";bootm $(kerneladdr)\0" \ + "netemergency=run bootargsdefaults;" \ + "dhcp $(copy_addr) $(kernelname);" \ + "set bootargs $(bootargs) root=initramfs boot=emergency " \ + ";bootm $(copy_addr)\0" \ + "norboot=run bootargsdefaults;" \ + "set bootargs $(bootargs) root=initramfs boot=local quiet " \ + ";bootm $(kerneladdr)\0" \ + "nandboot=run bootargsdefaults;" \ + "set bootargs $(bootargs) root=initramfs boot=nand " \ + ";bootm $(kerneladdr)\0" \ + "setnorboot=set bootcmd 'run norboot'; set bootdelay 1;save\0" \ + "clearenv=protect off 10060000 1007FFFF;" \ + "erase 10060000 1007FFFF;reset\0" \ + " " + +/*--------------------------------------------------------------------------*/ + +#ifdef CONFIG_USE_IRQ +#error CONFIG_USE_IRQ not supported +#endif + +#endif + +/* EOF */ -- 1.7.3.4

4 6

[U-Boot] [PATCH v4 0/6] Enable Thumb build for ARM platforms
by Aneesh V 07 Jul '12

07 Jul '12

Thumb is an alternate instruction set available in many ARM processors. Below is a detailed description from ARM specs: "The Thumb instruction set is a re-encoded subset of the ARM instruction set. Thumb instructions execute in their own processor state, with the architecture defining the mechanisms required to transition between ARM and Thumb states. The key difference is that Thumb instructions are half the size of ARM instructions(16 bits compared with 32 bits). Greater code density can usually be achieved by using the Thumb instruction set in preference to the ARM instruction set, at a cost of some reduction in performance" "In ARMv6T2, Thumb-2 technology is introduced. This technology makes it possible to extend the original Thumb instruction set with many 32-bit instructions. The range of 32-bit Thumb instructions included in ARMv6T2 permits Thumb code to achieve performance similar to ARM code, with code density better than that of earlier Thumb code. From ARMv6T2, the ARM and Thumb instruction sets provide almost identical functionality" This series adds Thumb support in U-Boot and enables it for OMAP4. It also fixes issues faced while booting OMAP4 with Thumb-2 images of U-Boot and SPL. Thumb mode is becoming increasingly relevant for U-Boot with the advent of SPL. It's very important to keep SPL size smaller considering the internal RAM size constraints on many platforms. On OMAP4 the size reduction enables us to use SPL on secure devices that have smaller internal RAM available for non-secure world. To enable support for new platforms you just need to add CONFIG_SYS_THUMB_BUILD in your config file. Tool-chains tried: 1. Sourcery G++ Lite 2010q1-202 arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2010q1-202) 4.4.1 GNU ld (Sourcery G++ Lite 2010q1-202) - binutils 2.19.51.20090709 2. Linaro 4.6-2012.01 arm-linux-gnueabi-gcc (crosstool-NG linaro-1.13.1-2012.01-20120125 - Linaro GCC 2012.01) 4.6.3 20120105 (prerelease) GNU ld (crosstool-NG linaro-1.13.1-2012.01-20120125 - Linaro GCC 2012.01) 2.22 Code-size reduction: Image ARM build Thumb build % Reduction u-boot.bin 190408 144676 24.01% u-boot-spl.bin 33200 25096 24.40% Performance(timestamp just before the main loop): ARM build Thumb build % Reduction 898510us 878247us -2.25% Performance actually improved marginally for the Thumb build, maybe because of the reduced image sizes. Aneesh V (6): arm: adapt asm/linkage.h from Linux armv7: add appropriate headers for assembly functions ARM: enable Thumb build armv7: Use -march=armv7-a and thereby enable Thumb-2 omap4+: Avoid using __attribute__ ((__packed__)) OMAP4: enable Thumb build README | 8 +++++ arch/arm/config.mk | 22 +++++++++---- arch/arm/cpu/armv7/config.mk | 7 +++- arch/arm/cpu/armv7/mx5/lowlevel_init.S | 5 ++- arch/arm/cpu/armv7/mx6/lowlevel_init.S | 5 ++- arch/arm/cpu/armv7/omap-common/lowlevel_init.S | 14 ++++---- arch/arm/cpu/armv7/omap-common/reset.S | 5 ++- arch/arm/cpu/armv7/omap3/lowlevel_init.S | 41 ++++++++++++----------- arch/arm/cpu/armv7/s5pc1xx/cache.S | 10 +++-- arch/arm/cpu/armv7/s5pc1xx/reset.S | 5 ++- arch/arm/cpu/armv7/start.S | 13 ++++--- arch/arm/cpu/armv7/tegra2/lowlevel_init.S | 5 ++- arch/arm/cpu/armv7/u8500/lowlevel.S | 9 +++-- arch/arm/include/asm/arch-omap4/mux_omap4.h | 2 +- arch/arm/include/asm/arch-omap5/mux_omap5.h | 2 +- arch/arm/include/asm/linkage.h | 7 ++++ include/configs/omap4_common.h | 2 + include/linux/linkage.h | 7 +++- 18 files changed, 106 insertions(+), 63 deletions(-) create mode 100644 arch/arm/include/asm/linkage.h

13 39

[U-Boot] [PATCH v4] at91: Add support for Bluewater Systems Snapper 9G45 module
by Simon Glass 30 Jun '12

30 Jun '12

Snapper 9G45 is a ARM9-based CPU module with 1GB NAND and 128MB DDR SDRAM. This patch includes NAND and Ethernet support. Signed-off-by: Simon Glass <sglass(a)bluewatersys.com> --- Changes in v2: - Removed unneeded i2c config - Added machine type define Changes in v3: - Use CONFIG_MACH_TYPE instead of custom code - Reduce PHY reset delay to minimum required Changes in v4: - Add MAINTAINERS entry and update Snapper boards since Ryan has moved - Fix ip= bootarg error - Remove I2C as this is not needed MAINTAINERS | 3 +- board/bluewater/snapper9g45/Makefile | 43 ++++++++ board/bluewater/snapper9g45/snapper9g45.c | 151 +++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/snapper9g45.h | 157 +++++++++++++++++++++++++++++ 5 files changed, 354 insertions(+), 1 deletions(-) create mode 100644 board/bluewater/snapper9g45/Makefile create mode 100644 board/bluewater/snapper9g45/snapper9g45.c create mode 100644 include/configs/snapper9g45.h diff --git a/MAINTAINERS b/MAINTAINERS index 576fea8..c12ee54 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -300,10 +300,11 @@ Dan Malek <dan(a)embeddedalley.com> stxssa MPC85xx stxxtc MPC8xx -Ryan Mallon <ryan(a)bluewatersys.com> +Simon Glass <sglass(a)bluewatersys.com> snapper9260 ARM926EJS (AT91SAM9260 SoC) snapper9g20 ARM926EJS (AT91SAM9G20 SoC) + snapper9g45 ARM926EJS (AT91SAM9G45 SoC) Eran Man <eran(a)nbase.co.il> diff --git a/board/bluewater/snapper9g45/Makefile b/board/bluewater/snapper9g45/Makefile new file mode 100644 index 0000000..9016e5a --- /dev/null +++ b/board/bluewater/snapper9g45/Makefile @@ -0,0 +1,43 @@ +# +# (C) Copyright 2003-2008 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += snapper9g45.o + +SRCS := $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/bluewater/snapper9g45/snapper9g45.c b/board/bluewater/snapper9g45/snapper9g45.c new file mode 100644 index 0000000..4e5afb1 --- /dev/null +++ b/board/bluewater/snapper9g45/snapper9g45.c @@ -0,0 +1,151 @@ +/* + * (C) Copyright 2011 Bluewater Systems Ltd + * Author: Andre Renaud <andre(a)bluewatersys.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/at91sam9g45_matrix.h> +#include <asm/arch/at91sam9_smc.h> +#include <asm/arch/at91_common.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_rstc.h> +#include <asm/arch/gpio.h> +#include <asm/arch/hardware.h> +#include <net.h> +#include <netdev.h> + +DECLARE_GLOBAL_DATA_PTR; + +static void macb_hw_init(void) +{ + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA; + struct at91_rstc *rstc = (struct at91_rstc *)ATMEL_BASE_RSTC; + unsigned long erstl; + + /* Enable clock */ + writel(1 << ATMEL_ID_EMAC, &pmc->pcer); + + /* + * Disable pull-up on: + * RXDV (PA15) => PHY normal mode (not Test mode) / CRSDV + * ERX0 (PA12) => PHY ADDR0 / RXD0 + * ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0 / RXD1 + * + * PHY has internal pull-down + */ + writel(pin_to_mask(AT91_PIN_PA15) | + pin_to_mask(AT91_PIN_PA12) | + pin_to_mask(AT91_PIN_PA13), + &pioa->pudr); + + /* Need to reset PHY -> needs 100us, so use minimum reset period */ + erstl = readl(&rstc->mr) & AT91_RSTC_MR_ERSTL_MASK; + writel(AT91_RSTC_KEY | AT91_RSTC_MR_ERSTL(0) | + AT91_RSTC_MR_URSTEN, &rstc->mr); + writel(AT91_RSTC_KEY | AT91_RSTC_CR_EXTRST, &rstc->cr); + + /* Wait for end hardware reset */ + while (!(readl(&rstc->sr) & AT91_RSTC_SR_NRSTL)) + ; + + /* Restore NRST value */ + writel(AT91_RSTC_KEY | erstl | AT91_RSTC_MR_URSTEN, &rstc->mr); + + /* The phy internal reset take 21ms */ + mdelay(21); + + /* Re-enable pull-up */ + writel(pin_to_mask(AT91_PIN_PA15) | + pin_to_mask(AT91_PIN_PA12) | + pin_to_mask(AT91_PIN_PA13), + &pioa->puer); + + at91_macb_hw_init(); +} + +static void nand_hw_init(void) +{ + struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; + struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; + unsigned long csa; + + /* Enable CS3 as NAND/SmartMedia */ + csa = readl(&matrix->ebicsa); + csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA; + writel(csa, &matrix->ebicsa); + + /* Configure SMC CS3 for NAND/SmartMedia */ + writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[3].setup); + writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(4) | + AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(4), + &smc->cs[3].pulse); + writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7), + &smc->cs[3].cycle); + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | + AT91_SMC_MODE_DBW_8 | + AT91_SMC_MODE_TDF_CYCLE(3), + &smc->cs[3].mode); + + /* Configure RDY/BSY */ + at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); + + /* Enable NandFlash */ + at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); +} + +int board_init(void) +{ + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + + /* Enable PIO clocks */ + writel((1 << ATMEL_ID_PIOA) | + (1 << ATMEL_ID_PIOB) | + (1 << ATMEL_ID_PIOC | + (1 << ATMEL_ID_PIODE)), &pmc->pcer); + + /* Address of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + + /* Initialise peripherals */ + at91_seriald_hw_init(); + nand_hw_init(); + + macb_hw_init(); + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + return macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x1b); +} + +int dram_init(void) +{ + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, + CONFIG_SYS_SDRAM_SIZE); + return 0; +} diff --git a/boards.cfg b/boards.cfg index 604becf..b6123c2 100644 --- a/boards.cfg +++ b/boards.cfg @@ -94,6 +94,7 @@ at91sam9xeek_dataflash_cs0 arm arm926ejs at91sam9260ek atmel at91sam9xeek_dataflash_cs1 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS1 snapper9260 arm arm926ejs - bluewater at91 snapper9260:AT91SAM9260 snapper9g20 arm arm926ejs snapper9260 bluewater at91 snapper9260:AT91SAM9G20 +snapper9g45 arm arm926ejs snapper9g45 bluewater at91 snapper9g45:AT91SAM9G45 sbc35_a9g20_nandflash arm arm926ejs sbc35_a9g20 calao at91 sbc35_a9g20:AT91SAM9G20,SYS_USE_NANDFLASH sbc35_a9g20_eeprom arm arm926ejs sbc35_a9g20 calao at91 sbc35_a9g20:AT91SAM9G20,SYS_USE_EEPROM tny_a9g20_nandflash arm arm926ejs tny_a9260 calao at91 tny_a9260:AT91SAM9G20,SYS_USE_NANDFLASH diff --git a/include/configs/snapper9g45.h b/include/configs/snapper9g45.h new file mode 100644 index 0000000..30181ad --- /dev/null +++ b/include/configs/snapper9g45.h @@ -0,0 +1,157 @@ +/* + * Bluewater Systems Snapper 9G45 modules + * + * (C) Copyright 2011 Bluewater Systems + * Author: Andre Renaud <andre(a)bluewatersys.com> + * Author: Ryan Mallon <ryan(a)bluewatersys.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* SoC type is defined in boards.cfg */ +#include <asm/hardware.h> +#include <asm/sizes.h> + +#define CONFIG_SYS_TEXT_BASE 0x70000000 + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* 12 MHz crystal */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 +#define CONFIG_SYS_HZ 1000 + +/* CPU */ +#define CONFIG_ARCH_CPU_INIT + +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_SKIP_LOWLEVEL_INIT + +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_FIT + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS6 +#define CONFIG_SYS_SDRAM_SIZE (128 * 1024 * 1024) /* 128MB */ +#define CONFIG_SYS_INIT_SP_ADDR (ATMEL_BASE_SRAM + 0x1000 - \ + GENERATED_GBL_DATA_SIZE) + +/* Mem test settings */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + (1024 * 1024)) + +/* NAND flash */ +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_NO_FLASH +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 /*0x40000000*/ +#define CONFIG_SYS_NAND_DBW_8 +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* AD21 */ +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) /* AD22 */ +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC8 + +/* Ethernet */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_TFTP_PORT +#define CONFIG_TFTP_TSIZE + +/* USB */ +#define CONFIG_USB_ATMEL +#define CONFIG_USB_OHCI_NEW +#define CONFIG_DOS_PARTITION +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00700000 /* _UHP_OHCI_BASE */ +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g45" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 +#define CONFIG_USB_STORAGE + +/* GPIOs and IO expander */ +#define CONFIG_AT91_LEGACY +#define CONFIG_ATMEL_LEGACY +#define CONFIG_AT91_GPIO +#define CONFIG_AT91_GPIO_PULLUP 1 + +/* UARTs/Serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_SYS +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 } +#define CONFIG_SYS_PROMPT "Snapper> " + +/* Boot options */ +#define CONFIG_SYS_LOAD_ADDR 0x71000000 +#define CONFIG_BOOTDELAY 3 +#define CONFIG_ZERO_BOOTDELAY_CHECK + +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* Environment settings */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET (512 << 10) +#define CONFIG_ENV_SIZE (256 << 10) +#define CONFIG_ENV_OVERWRITE +#define CONFIG_BOOTARGS "console=ttyS0,115200 ip=dhcp" + +/* Console settings */ +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_EXTBDINFO +#define CONFIG_CMDLINE_EDITING +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* U-Boot memory settings */ +#define CONFIG_SYS_MALLOC_LEN (1 << 20) +#define CONFIG_STACKSIZE (256 << 10) +#define CONFIG_MACH_TYPE 2817 + +/* Command line configuration */ +#include <config_cmd_default.h> + +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_LOADS +#undef CONFIG_CMD_SOURCE + +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_FAT +#undef CONFIG_CMD_GPIO +#define CONFIG_CMD_USB +#define CONFIG_CMD_MII +#define CONFIG_CMD_NAND + +#endif -- 1.7.5.4

2 1

[U-Boot] [PATCH] Fix: brocken boot message at serial line on AT91SAM9263-EK board
by Jens Scharsig (BuS Elektronik) 28 Jun '12

28 Jun '12

Signed-off-by: Jens Scharsig (BuS Elektronik) <esw(a)bus-elektronik.de> --- board/atmel/at91sam9263ek/at91sam9263ek.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-) diff --git a/board/atmel/at91sam9263ek/at91sam9263ek.c b/board/atmel/at91sam9263ek/at91sam9263ek.c index 41ec752..60ff1c0 100644 --- a/board/atmel/at91sam9263ek/at91sam9263ek.c +++ b/board/atmel/at91sam9263ek/at91sam9263ek.c @@ -254,6 +254,7 @@ int board_early_init_f(void) (1 << ATMEL_ID_PIOCDE), &pmc->pcer); + at91_seriald_hw_init(); return 0; } @@ -267,7 +268,6 @@ int board_init(void) /* adress of boot parameters */ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; - at91_seriald_hw_init(); #ifdef CONFIG_CMD_NAND at91sam9263ek_nand_hw_init(); #endif -- 1.7.3.4

2 1

[U-Boot] [PATCH] Fix: AT91SAM9263 nor flash usage Fix: board doesn't boot from norflash Fix: environment can't write to flash (end address/start address not on sector boundary)
by Jens Scharsig (BuS Elektronik) 28 Jun '12

28 Jun '12

Signed-off-by: Jens Scharsig (BuS Elektronik) <esw(a)bus-elektronik.de> --- include/configs/at91sam9263ek.h | 8 ++++++-- 1 files changed, 6 insertions(+), 2 deletions(-) diff --git a/include/configs/at91sam9263ek.h b/include/configs/at91sam9263ek.h index 8399246..f02f245 100644 --- a/include/configs/at91sam9263ek.h +++ b/include/configs/at91sam9263ek.h @@ -33,7 +33,11 @@ */ #include <asm/hardware.h> +#ifndef CONFIG_SYS_USE_BOOT_NORFLASH #define CONFIG_SYS_TEXT_BASE 0x21F00000 +#else +#define CONFIG_SYS_TEXT_BASE 0x0000000 +#endif /* ARM asynchronous clock */ #define CONFIG_SYS_AT91_MAIN_CLOCK 16367660 /* 16.367 MHz crystal */ @@ -148,11 +152,11 @@ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_MONITOR_LEN (256 << 10) #define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x007FE000) +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x007E0000) #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SIZE) /* Address and size of Primary Environment Sector */ -#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SIZE 0x10000 #define xstr(s) str(s) #define str(s) #s -- 1.7.3.4

3 3

[U-Boot] [PATCH v2] skat91: add support for SK-AT91SAM9/SIM508 board
by Vladimir Zapolskiy 28 Jun '12

28 Jun '12

This change adds complete support for Starterkit SK-AT91SAM9/SIM508 board. Signed-off-by: Vladimir Zapolskiy <vz(a)mleia.com> Cc: Albert ARIBAUD <albert.u.boot(a)aribaud.net> Cc: Wolfgang Denk <wd(a)denx.de> --- Changes from v1 to v2: * make use of setbits_le32() and similar helpers * phy address is defined explicitly * removed CONFIG_EXTRA_ENV_SETTINGS MAINTAINERS | 4 + board/starterkit/skat91_sim508/Makefile | 44 ++++++ board/starterkit/skat91_sim508/partition.c | 39 +++++ board/starterkit/skat91_sim508/skat91_sim508.c | 122 ++++++++++++++++ boards.cfg | 2 + include/configs/skat91_sim508.h | 178 ++++++++++++++++++++++++ 6 files changed, 389 insertions(+), 0 deletions(-) create mode 100644 board/starterkit/skat91_sim508/Makefile create mode 100644 board/starterkit/skat91_sim508/partition.c create mode 100644 board/starterkit/skat91_sim508/skat91_sim508.c create mode 100644 include/configs/skat91_sim508.h diff --git a/MAINTAINERS b/MAINTAINERS index 4bf12b5..bcd330a 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -914,6 +914,10 @@ Sughosh Ganu <urwithsughosh(a)gmail.com> hawkboard ARM926EJS (OMAP-L138) +Vladimir Zapolskiy <vz(a)mleia.com> + + skat91_sim508 ARM926EJS (AT91SAM9260 SoC) + ------------------------------------------------------------------------- Unknown / orphaned boards: diff --git a/board/starterkit/skat91_sim508/Makefile b/board/starterkit/skat91_sim508/Makefile new file mode 100644 index 0000000..77965f8 --- /dev/null +++ b/board/starterkit/skat91_sim508/Makefile @@ -0,0 +1,44 @@ +# +# Copyright (C) 2011 by Vladimir Zapolskiy <vz(a)mleia.com> +# Copyright (C) 2008, Guennadi Liakhovetski <lg(a)denx.de> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301, USA. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := skat91_sim508.o partition.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/starterkit/skat91_sim508/partition.c b/board/starterkit/skat91_sim508/partition.c new file mode 100644 index 0000000..f82046d --- /dev/null +++ b/board/starterkit/skat91_sim508/partition.c @@ -0,0 +1,39 @@ +/* + * StarterKit SK-AT91SAM9/SIM508 board support, dataflash partitions + * + * Copyright (C) 2011 Vladimir Zapolskiy <vz(a)mleia.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#include <common.h> +#include <config.h> +#include <asm/hardware.h> +#include <dataflash.h> + +AT91S_DATAFLASH_INFO dataflash_info[CONFIG_SYS_MAX_DATAFLASH_BANKS]; + +struct dataflash_addr cs[CONFIG_SYS_MAX_DATAFLASH_BANKS] = { + { CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0, 0 }, +}; + +/* define the area offsets */ +dataflash_protect_t area_list[NB_DATAFLASH_AREA] = { + { 0x00000000, 0x00003FFF, FLAG_PROTECT_SET, 0, "Bootstrap" }, + { 0x00004000, 0x00007FFF, FLAG_PROTECT_CLEAR, 0, "Environment" }, + { 0x00008000, 0x00037FFF, FLAG_PROTECT_SET, 0, "U-Boot" }, + { 0x00038000, 0x0041FFFF, FLAG_PROTECT_CLEAR, 0, "Kernel" }, +}; diff --git a/board/starterkit/skat91_sim508/skat91_sim508.c b/board/starterkit/skat91_sim508/skat91_sim508.c new file mode 100644 index 0000000..1ddafab --- /dev/null +++ b/board/starterkit/skat91_sim508/skat91_sim508.c @@ -0,0 +1,122 @@ +/* + * StarterKit SK-AT91SAM9/SIM508 board support + * + * Copyright (C) 2011 Vladimir Zapolskiy <vz(a)mleia.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#include <common.h> +#include <netdev.h> + +#include <asm/arch/at91sam9260_matrix.h> +#include <asm/arch/at91sam9_smc.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_pio.h> +#include <asm/arch/at91_rstc.h> +#include <asm/arch/at91_common.h> +#include <asm/arch/gpio.h> +#include <asm/io.h> + +DECLARE_GLOBAL_DATA_PTR; + +#ifdef CONFIG_CMD_NAND +static void skat91_sim508_nand_hw_init(void) +{ + struct at91_pmc *pmc = (at91_pmc_t *)ATMEL_BASE_PMC; + struct at91_smc *smc = (at91_smc_t *)ATMEL_BASE_SMC; + struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; + + /* Assign CS3 to NAND/SmartMedia Interface */ + setbits_le32(&matrix->ebicsa, AT91_MATRIX_CS3A_SMC_SMARTMEDIA); + + /* Configure SMC CS3 for NAND/SmartMedia */ + writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[3].setup); + + writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | + AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), + &smc->cs[3].pulse); + + writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), + &smc->cs[3].cycle); + + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | + AT91_SMC_MODE_DBW_8 | + AT91_SMC_MODE_TDF_CYCLE(2), + &smc->cs[3].mode); + + writel(1 << ATMEL_ID_PIOC, &pmc->pcer); + + /* Configure RDY/BSY */ + at91_set_pio_input(CONFIG_SYS_NAND_READY_PIN, 1); + + /* Enable NandFlash */ + at91_set_pio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); +} +#endif + +#ifdef CONFIG_MACB +static void skat91_sim508_macb_hw_init(void) +{ + at91_pmc_t *pmc = (at91_pmc_t *)ATMEL_BASE_PMC; + + /* Enable EMAC clock */ + writel(1 << ATMEL_ID_EMAC0, &pmc->pcer); + + at91_macb_hw_init(); +} + +int board_eth_init(bd_t *bis) +{ + return macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, + CONFIG_PHY_ADDR); +} +#endif + +int board_early_init_f(void) +{ + at91_seriald_hw_init(); + + return 0; +} + +int board_init(void) +{ + /* Enable Ctrlc */ + console_init_f(); + + /* adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + +#ifdef CONFIG_CMD_NAND + skat91_sim508_nand_hw_init(); +#endif +#ifdef CONFIG_MACB + skat91_sim508_macb_hw_init(); +#endif + return 0; +} + +int dram_init(void) +{ + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, + CONFIG_SYS_SDRAM_SIZE); + + return 0; +} diff --git a/boards.cfg b/boards.cfg index 0b32532..6dd2269 100644 --- a/boards.cfg +++ b/boards.cfg @@ -118,6 +118,8 @@ cpu9G20_nand_128M arm arm926ejs cpu9260 eukrea pm9261 arm arm926ejs pm9261 ronetix at91 pm9261:AT91SAM9261 pm9263 arm arm926ejs pm9263 ronetix at91 pm9263:AT91SAM9263 pm9g45 arm arm926ejs pm9g45 ronetix at91 pm9g45:AT91SAM9G45 +skat91_sim508 arm arm926ejs skat91_sim508 starterkit at91 skat91_sim508:AT91SAM9260,SYS_USE_NANDFLASH +skat91_sim508_dataflash arm arm926ejs skat91_sim508 starterkit at91 skat91_sim508:AT91SAM9260,SYS_USE_DATAFLASH_CS0 cam_enc_4xx arm arm926ejs cam_enc_4xx ait davinci cam_enc_4xx da830evm arm arm926ejs da8xxevm davinci davinci da850_am18xxevm arm arm926ejs da8xxevm davinci davinci diff --git a/include/configs/skat91_sim508.h b/include/configs/skat91_sim508.h new file mode 100644 index 0000000..794b7d7 --- /dev/null +++ b/include/configs/skat91_sim508.h @@ -0,0 +1,178 @@ +/* + * Starterkit SK-AT91SAM9/SIM508 board configuration file + * + * Copyright (C) 2011 Vladimir Zapolskiy <vz(a)mleia.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#ifndef __CONFIG_SKAT91_SIM508_H__ +#define __CONFIG_SKAT91_SIM508_H__ + +#include <asm/sizes.h> +#include <asm/hardware.h> + +/* Define SK-AT91SAM9/SIM508 machine type by hand */ +#define MACH_TYPE_SKAT91_SIM508 2789 +#define CONFIG_MACH_TYPE MACH_TYPE_SKAT91_SIM508 + +#define CONFIG_SYS_ICACHE_OFF +#define CONFIG_SYS_DCACHE_OFF +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 +#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 +#define CONFIG_SYS_HZ 1000 + +/* SoC configurations */ +#define CONFIG_ARCH_CPU_INIT + +/* Memory configurations */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_STACKSIZE SZ_32K +#define CONFIG_SYS_MALLOC_LEN SZ_1M +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 +#define CONFIG_SYS_SDRAM_SIZE SZ_64M +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE - SZ_1M) + +#define CONFIG_SYS_TEXT_BASE 0x23F00000 +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_MEMTEST_START + SZ_32K) + +#define CONFIG_SYS_INIT_RAM_SIZE SZ_4K +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \ + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET + +/* Hardware drivers */ +#define CONFIG_AT91_GPIO + +/* Serial driver */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_SYS +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 115200 , 57600, 38400, 19200, 9600 } + +/* DataFlash */ +#define CONFIG_CMD_FLASH +#define CONFIG_ATMEL_DATAFLASH_SPI +#define CONFIG_HAS_DATAFLASH +#define CONFIG_SYS_SPI_WRITE_TOUT (5 * CONFIG_SYS_HZ) +#define CONFIG_SYS_MAX_DATAFLASH_BANKS 1 +#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 +#define AT91_SPI_CLK 15000000 +#define DATAFLASH_TCSS (0x1a << 16) +#define DATAFLASH_TCHS (0x01 << 24) + +/* NOR flash - no real flash on this board */ +#define CONFIG_SYS_NO_FLASH + +/* NAND Flash */ +#define CONFIG_CMD_NAND +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 +#define CONFIG_SYS_NAND_DBW_8 1 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTC, 13 +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTC, 14 +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) + +/* Ethernet */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_NET_RETRY_COUNT 20 + +#define CONFIG_PHYLIB +#define CONFIG_PHY_MICREL +#define CONFIG_PHY_ADDR 0x01 + +/* U-Boot General Configurations */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_PROMPT "=> " +#define CONFIG_SYS_CBSIZE 1024 +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_AUTO_COMPLETE +#define CONFIG_CMDLINE_EDITING +#define CONFIG_VERSION_VARIABLE +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DOS_PARTITION + +#if defined(CONFIG_SYS_USE_DATAFLASH_CS0) +#define CONFIG_ENV_IS_IN_DATAFLASH +#define CONFIG_SYS_MONITOR_BASE \ + (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + 0x8000) +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_ADDR \ + (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + CONFIG_ENV_OFFSET) +#define CONFIG_ENV_SIZE SZ_16K +#define CONFIG_BOOTCOMMAND "cp.b 0xC0038000 0x20400000 0x170000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock0 " \ + "mtdparts=atmel_nand:-(root) " \ + "rw rootfstype=jffs2" +#elif defined(CONFIG_SYS_USE_NANDFLASH) +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x020000 +#define CONFIG_ENV_SIZE SZ_128K +#define CONFIG_BOOTCOMMAND "nand read 0x20400000 0x80000 0x200000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock5 " \ + "mtdparts=atmel_nand:128k(bootstrap)ro,"\ + "256k(uboot)ro,128k(env)ro," \ + "2M(linux),-(root) " \ + "rw rootfstype=jffs2" +#else +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_SIZE SZ_128K +#define CONFIG_BOOTARGS "console=ttyS2,115200n8" +#endif + +/* U-Boot Commands */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_LOADS + +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP + +/* BOOTP options */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* Boot Linux */ +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_ZERO_BOOTDELAY_CHECK +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_LOADADDR 0x20400000 + +#endif /* __CONFIG_SKAT91_SIM508_H__ */ -- 1.7.5.4

3 2

[U-Boot] [PATCH 0/7] PXE parsing fixes and local file support
by Rob Herring 21 Jun '12

21 Jun '12

From: Rob Herring <rob.herring(a)calxeda.com> The first 6 patches are menu file parsing fixes found in testing ubuntu/ debian generated menu files. The menu display is cleaned up to display the friendly menu label string and boot the default image on timeout as is typical for a PC bootloader. The last patch adds support for parsing local disk files on ext2 or fat filesystems. This is essentially syslinux/extlinux emulation and simply reuses the existing pxe support. Rob Rob Herring (7): menu: only timeout when menu is displayed pxe: support include files at top-level pxe: add support for label menu text pxe: support linux entries for labels pxe: support absolute paths pxe: parse initrd file from append string pxe: add support for parsing local syslinux files common/cmd_pxe.c | 198 +++++++++++++++++++++++++++++++++++++++++++++++------- common/menu.c | 36 +--------- doc/README.pxe | 3 - include/common.h | 6 ++ 4 files changed, 184 insertions(+), 59 deletions(-) -- 1.7.5.4

3 21

[U-Boot] [PATCH] bootstage: Fix build error for standalone API example
by Simon Glass 21 Jun '12

21 Jun '12

This example doesn't have get_timer() defined, which causes build breakages. Add #ifdef guards to work around this. Signed-off-by: Simon Glass <sjg(a)chromium.org> --- lib/time.c | 2 ++ 1 files changed, 2 insertions(+), 0 deletions(-) diff --git a/lib/time.c b/lib/time.c index 69edc3d..5f393c3 100644 --- a/lib/time.c +++ b/lib/time.c @@ -48,6 +48,7 @@ void mdelay(unsigned long msec) udelay(1000); } +#ifdef CONFIG_BOOTSTAGE ulong __timer_get_boot_us(void) { static ulong base_time; @@ -64,3 +65,4 @@ ulong __timer_get_boot_us(void) ulong timer_get_boot_us(void) __attribute__((weak, alias("__timer_get_boot_us"))); +#endif -- 1.7.7.3

3 4