September 2008 - U-Boot

[U-Boot] [PATCH v2] net: ne2000: Divided a function of NE2000 driver
by Nobuhiro Iwamatsu 03 Oct '08

03 Oct '08

get_prom function was used __attriute__ , but it is not enable. ax88796.o does not do link besides ne2000.o. When ld is carried out, get_prom function of ax88796.c is ignored. This problem is a thing by specifications of ld. I checked and test this patch on SuperH and MIPS. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro(a)renesas.com> --- I forgot attach drivers/net/ne2000_base.c drivers/net/Makefile | 6 +- drivers/net/ax88796.c | 2 +- drivers/net/ne2000.c | 719 +------------------------------------------ drivers/net/ne2000_base.c | 757 +++++++++++++++++++++++++++++++++++++++++++++ drivers/net/ne2000_base.h | 36 ++- 5 files changed, 797 insertions(+), 723 deletions(-) create mode 100644 drivers/net/ne2000_base.c diff --git a/drivers/net/Makefile b/drivers/net/Makefile index a084000..a4ea3a2 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -44,10 +44,8 @@ COBJS-$(CONFIG_MCFFEC) += mcffec.o COBJS-$(CONFIG_MPC5xxx_FEC) += mpc5xxx_fec.o COBJS-$(CONFIG_MPC512x_FEC) += mpc512x_fec.o COBJS-$(CONFIG_NATSEMI) += natsemi.o -ifeq ($(CONFIG_DRIVER_NE2000),y) -COBJS-y += ne2000.o -COBJS-$(CONFIG_DRIVER_AX88796L) += ax88796.o -endif +COBJS-$(CONFIG_DRIVER_NE2000) += ne2000.o ne2000_base.o +COBJS-$(CONFIG_DRIVER_AX88796L) += ax88796.o ne2000_base.o COBJS-$(CONFIG_DRIVER_NETARMETH) += netarm_eth.o COBJS-$(CONFIG_NETCONSOLE) += netconsole.o COBJS-$(CONFIG_DRIVER_NS7520_ETHERNET) += ns7520_eth.o diff --git a/drivers/net/ax88796.c b/drivers/net/ax88796.c index 39cd101..2089141 100644 --- a/drivers/net/ax88796.c +++ b/drivers/net/ax88796.c @@ -143,7 +143,7 @@ static void ax88796_mac_read(u8 *buff) } } -int get_prom(u8* mac_addr) +int get_prom(u8* mac_addr, u8* base_addr) { u8 prom[32]; int i; diff --git a/drivers/net/ne2000.c b/drivers/net/ne2000.c index ec92485..ab5eec7 100644 --- a/drivers/net/ne2000.c +++ b/drivers/net/ne2000.c @@ -74,600 +74,11 @@ Add SNMP #include <common.h> #include <command.h> -#include <net.h> -#include <malloc.h> - -#define mdelay(n) udelay((n)*1000) -/* forward definition of function used for the uboot interface */ -void uboot_push_packet_len(int len); -void uboot_push_tx_done(int key, int val); - -/* - * Debugging details - * - * Set to perms of: - * 0 disables all debug output - * 1 for process debug output - * 2 for added data IO output: get_reg, put_reg - * 4 for packet allocation/free output - * 8 for only startup status, so we can tell we're installed OK - */ -#if 0 -#define DEBUG 0xf -#else -#define DEBUG 0 -#endif - -#if DEBUG & 1 -#define DEBUG_FUNCTION() do { printf("%s\n", __FUNCTION__); } while (0) -#define DEBUG_LINE() do { printf("%d\n", __LINE__); } while (0) -#define PRINTK(args...) printf(args) -#else -#define DEBUG_FUNCTION() do {} while(0) -#define DEBUG_LINE() do {} while(0) -#define PRINTK(args...) -#endif /* NE2000 base header file */ #include "ne2000_base.h" -#if defined(CONFIG_DRIVER_AX88796L) -/* AX88796L support */ -#include "ax88796.h" -#else -/* Basic NE2000 chip support */ -#include "ne2000.h" -#endif - -static dp83902a_priv_data_t nic; /* just one instance of the card supported */ - -static bool -dp83902a_init(void) -{ - dp83902a_priv_data_t *dp = &nic; - u8* base; -#if defined(NE2000_BASIC_INIT) - int i; -#endif - - DEBUG_FUNCTION(); - - base = dp->base; - if (!base) - return false; /* No device found */ - - DEBUG_LINE(); - -#if defined(NE2000_BASIC_INIT) - /* AX88796L doesn't need */ - /* Prepare ESA */ - DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE1); /* Select page 1 */ - /* Use the address from the serial EEPROM */ - for (i = 0; i < 6; i++) - DP_IN(base, DP_P1_PAR0+i, dp->esa[i]); - DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE0); /* Select page 0 */ - - printf("NE2000 - %s ESA: %02x:%02x:%02x:%02x:%02x:%02x\n", - "eeprom", - dp->esa[0], - dp->esa[1], - dp->esa[2], - dp->esa[3], - dp->esa[4], - dp->esa[5] ); - -#endif /* NE2000_BASIC_INIT */ - return true; -} - -static void -dp83902a_stop(void) -{ - dp83902a_priv_data_t *dp = &nic; - u8 *base = dp->base; - - DEBUG_FUNCTION(); - - DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_STOP); /* Brutal */ - DP_OUT(base, DP_ISR, 0xFF); /* Clear any pending interrupts */ - DP_OUT(base, DP_IMR, 0x00); /* Disable all interrupts */ - - dp->running = false; -} - -/* - * This function is called to "start up" the interface. It may be called - * multiple times, even when the hardware is already running. It will be - * called whenever something "hardware oriented" changes and should leave - * the hardware ready to send/receive packets. - */ -static void -dp83902a_start(u8 * enaddr) -{ - dp83902a_priv_data_t *dp = &nic; - u8 *base = dp->base; - int i; - - DEBUG_FUNCTION(); - - DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_STOP); /* Brutal */ - DP_OUT(base, DP_DCR, DP_DCR_INIT); - DP_OUT(base, DP_RBCH, 0); /* Remote byte count */ - DP_OUT(base, DP_RBCL, 0); - DP_OUT(base, DP_RCR, DP_RCR_MON); /* Accept no packets */ - DP_OUT(base, DP_TCR, DP_TCR_LOCAL); /* Transmitter [virtually] off */ - DP_OUT(base, DP_TPSR, dp->tx_buf1); /* Transmitter start page */ - dp->tx1 = dp->tx2 = 0; - dp->tx_next = dp->tx_buf1; - dp->tx_started = false; - dp->running = true; - DP_OUT(base, DP_PSTART, dp->rx_buf_start); /* Receive ring start page */ - DP_OUT(base, DP_BNDRY, dp->rx_buf_end - 1); /* Receive ring boundary */ - DP_OUT(base, DP_PSTOP, dp->rx_buf_end); /* Receive ring end page */ - dp->rx_next = dp->rx_buf_start - 1; - dp->running = true; - DP_OUT(base, DP_ISR, 0xFF); /* Clear any pending interrupts */ - DP_OUT(base, DP_IMR, DP_IMR_All); /* Enable all interrupts */ - DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE1 | DP_CR_STOP); /* Select page 1 */ - DP_OUT(base, DP_P1_CURP, dp->rx_buf_start); /* Current page - next free page for Rx */ - dp->running = true; - for (i = 0; i < ETHER_ADDR_LEN; i++) { - /* FIXME */ - /*((vu_short*)( base + ((DP_P1_PAR0 + i) * 2) + - * 0x1400)) = enaddr[i];*/ - DP_OUT(base, DP_P1_PAR0+i, enaddr[i]); - } - /* Enable and start device */ - DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START); - DP_OUT(base, DP_TCR, DP_TCR_NORMAL); /* Normal transmit operations */ - DP_OUT(base, DP_RCR, DP_RCR_AB); /* Accept broadcast, no errors, no multicast */ - dp->running = true; -} - -/* - * This routine is called to start the transmitter. It is split out from the - * data handling routine so it may be called either when data becomes first - * available or when an Tx interrupt occurs - */ - -static void -dp83902a_start_xmit(int start_page, int len) -{ - dp83902a_priv_data_t *dp = (dp83902a_priv_data_t *) &nic; - u8 *base = dp->base; - - DEBUG_FUNCTION(); - -#if DEBUG & 1 - printf("Tx pkt %d len %d\n", start_page, len); - if (dp->tx_started) - printf("TX already started?!?\n"); -#endif - - DP_OUT(base, DP_ISR, (DP_ISR_TxP | DP_ISR_TxE)); - DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START); - DP_OUT(base, DP_TBCL, len & 0xFF); - DP_OUT(base, DP_TBCH, len >> 8); - DP_OUT(base, DP_TPSR, start_page); - DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_TXPKT | DP_CR_START); - - dp->tx_started = true; -} - -/* - * This routine is called to send data to the hardware. It is known a-priori - * that there is free buffer space (dp->tx_next). - */ -static void -dp83902a_send(u8 *data, int total_len, u32 key) -{ - struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - u8 *base = dp->base; - int len, start_page, pkt_len, i, isr; -#if DEBUG & 4 - int dx; -#endif - - DEBUG_FUNCTION(); - - len = pkt_len = total_len; - if (pkt_len < IEEE_8023_MIN_FRAME) - pkt_len = IEEE_8023_MIN_FRAME; - - start_page = dp->tx_next; - if (dp->tx_next == dp->tx_buf1) { - dp->tx1 = start_page; - dp->tx1_len = pkt_len; - dp->tx1_key = key; - dp->tx_next = dp->tx_buf2; - } else { - dp->tx2 = start_page; - dp->tx2_len = pkt_len; - dp->tx2_key = key; - dp->tx_next = dp->tx_buf1; - } - -#if DEBUG & 5 - printf("TX prep page %d len %d\n", start_page, pkt_len); -#endif - - DP_OUT(base, DP_ISR, DP_ISR_RDC); /* Clear end of DMA */ - { - /* - * Dummy read. The manual sez something slightly different, - * but the code is extended a bit to do what Hitachi's monitor - * does (i.e., also read data). - */ - - u16 tmp; - int len = 1; - - DP_OUT(base, DP_RSAL, 0x100 - len); - DP_OUT(base, DP_RSAH, (start_page - 1) & 0xff); - DP_OUT(base, DP_RBCL, len); - DP_OUT(base, DP_RBCH, 0); - DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_RDMA | DP_CR_START); - DP_IN_DATA(dp->data, tmp); - } - -#ifdef CYGHWR_NS_DP83902A_PLF_BROKEN_TX_DMA - /* - * Stall for a bit before continuing to work around random data - * corruption problems on some platforms. - */ - CYGACC_CALL_IF_DELAY_US(1); -#endif - - /* Send data to device buffer(s) */ - DP_OUT(base, DP_RSAL, 0); - DP_OUT(base, DP_RSAH, start_page); - DP_OUT(base, DP_RBCL, pkt_len & 0xFF); - DP_OUT(base, DP_RBCH, pkt_len >> 8); - DP_OUT(base, DP_CR, DP_CR_WDMA | DP_CR_START); - - /* Put data into buffer */ -#if DEBUG & 4 - printf(" sg buf %08lx len %08x\n ", (u32)data, len); - dx = 0; -#endif - while (len > 0) { -#if DEBUG & 4 - printf(" %02x", *data); - if (0 == (++dx % 16)) printf("\n "); -#endif - - DP_OUT_DATA(dp->data, *data++); - len--; - } -#if DEBUG & 4 - printf("\n"); -#endif - if (total_len < pkt_len) { -#if DEBUG & 4 - printf(" + %d bytes of padding\n", pkt_len - total_len); -#endif - /* Padding to 802.3 length was required */ - for (i = total_len; i < pkt_len;) { - i++; - DP_OUT_DATA(dp->data, 0); - } - } - -#ifdef CYGHWR_NS_DP83902A_PLF_BROKEN_TX_DMA - /* - * After last data write, delay for a bit before accessing the - * device again, or we may get random data corruption in the last - * datum (on some platforms). - */ - CYGACC_CALL_IF_DELAY_US(1); -#endif - - /* Wait for DMA to complete */ - do { - DP_IN(base, DP_ISR, isr); - } while ((isr & DP_ISR_RDC) == 0); - - /* Then disable DMA */ - DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START); - - /* Start transmit if not already going */ - if (!dp->tx_started) { - if (start_page == dp->tx1) { - dp->tx_int = 1; /* Expecting interrupt from BUF1 */ - } else { - dp->tx_int = 2; /* Expecting interrupt from BUF2 */ - } - dp83902a_start_xmit(start_page, pkt_len); - } -} - -/* - * This function is called when a packet has been received. It's job is - * to prepare to unload the packet from the hardware. Once the length of - * the packet is known, the upper layer of the driver can be told. When - * the upper layer is ready to unload the packet, the internal function - * 'dp83902a_recv' will be called to actually fetch it from the hardware. - */ -static void -dp83902a_RxEvent(void) -{ - struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - u8 *base = dp->base; - u8 rsr; - u8 rcv_hdr[4]; - int i, len, pkt, cur; - - DEBUG_FUNCTION(); - - DP_IN(base, DP_RSR, rsr); - while (true) { - /* Read incoming packet header */ - DP_OUT(base, DP_CR, DP_CR_PAGE1 | DP_CR_NODMA | DP_CR_START); - DP_IN(base, DP_P1_CURP, cur); - DP_OUT(base, DP_P1_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START); - DP_IN(base, DP_BNDRY, pkt); - - pkt += 1; - if (pkt == dp->rx_buf_end) - pkt = dp->rx_buf_start; - - if (pkt == cur) { - break; - } - DP_OUT(base, DP_RBCL, sizeof(rcv_hdr)); - DP_OUT(base, DP_RBCH, 0); - DP_OUT(base, DP_RSAL, 0); - DP_OUT(base, DP_RSAH, pkt); - if (dp->rx_next == pkt) { - if (cur == dp->rx_buf_start) - DP_OUT(base, DP_BNDRY, dp->rx_buf_end - 1); - else - DP_OUT(base, DP_BNDRY, cur - 1); /* Update pointer */ - return; - } - dp->rx_next = pkt; - DP_OUT(base, DP_ISR, DP_ISR_RDC); /* Clear end of DMA */ - DP_OUT(base, DP_CR, DP_CR_RDMA | DP_CR_START); -#ifdef CYGHWR_NS_DP83902A_PLF_BROKEN_RX_DMA - CYGACC_CALL_IF_DELAY_US(10); -#endif - - /* read header (get data size)*/ - for (i = 0; i < sizeof(rcv_hdr);) { - DP_IN_DATA(dp->data, rcv_hdr[i++]); - } - -#if DEBUG & 5 - printf("rx hdr %02x %02x %02x %02x\n", - rcv_hdr[0], rcv_hdr[1], rcv_hdr[2], rcv_hdr[3]); -#endif - len = ((rcv_hdr[3] << 8) | rcv_hdr[2]) - sizeof(rcv_hdr); - - /* data read */ - uboot_push_packet_len(len); - - if (rcv_hdr[1] == dp->rx_buf_start) - DP_OUT(base, DP_BNDRY, dp->rx_buf_end - 1); - else - DP_OUT(base, DP_BNDRY, rcv_hdr[1] - 1); /* Update pointer */ - } -} - -/* - * This function is called as a result of the "eth_drv_recv()" call above. - * It's job is to actually fetch data for a packet from the hardware once - * memory buffers have been allocated for the packet. Note that the buffers - * may come in pieces, using a scatter-gather list. This allows for more - * efficient processing in the upper layers of the stack. - */ -static void -dp83902a_recv(u8 *data, int len) -{ - struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - u8 *base = dp->base; - int i, mlen; - u8 saved_char = 0; - bool saved; -#if DEBUG & 4 - int dx; -#endif - - DEBUG_FUNCTION(); - -#if DEBUG & 5 - printf("Rx packet %d length %d\n", dp->rx_next, len); -#endif - - /* Read incoming packet data */ - DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START); - DP_OUT(base, DP_RBCL, len & 0xFF); - DP_OUT(base, DP_RBCH, len >> 8); - DP_OUT(base, DP_RSAL, 4); /* Past header */ - DP_OUT(base, DP_RSAH, dp->rx_next); - DP_OUT(base, DP_ISR, DP_ISR_RDC); /* Clear end of DMA */ - DP_OUT(base, DP_CR, DP_CR_RDMA | DP_CR_START); -#ifdef CYGHWR_NS_DP83902A_PLF_BROKEN_RX_DMA - CYGACC_CALL_IF_DELAY_US(10); -#endif - - saved = false; - for (i = 0; i < 1; i++) { - if (data) { - mlen = len; -#if DEBUG & 4 - printf(" sg buf %08lx len %08x \n", (u32) data, mlen); - dx = 0; -#endif - while (0 < mlen) { - /* Saved byte from previous loop? */ - if (saved) { - *data++ = saved_char; - mlen--; - saved = false; - continue; - } - - { - u8 tmp; - DP_IN_DATA(dp->data, tmp); -#if DEBUG & 4 - printf(" %02x", tmp); - if (0 == (++dx % 16)) printf("\n "); -#endif - *data++ = tmp;; - mlen--; - } - } -#if DEBUG & 4 - printf("\n"); -#endif - } - } -} - -static void -dp83902a_TxEvent(void) -{ - struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - u8 *base = dp->base; - u8 tsr; - u32 key; - - DEBUG_FUNCTION(); - - DP_IN(base, DP_TSR, tsr); - if (dp->tx_int == 1) { - key = dp->tx1_key; - dp->tx1 = 0; - } else { - key = dp->tx2_key; - dp->tx2 = 0; - } - /* Start next packet if one is ready */ - dp->tx_started = false; - if (dp->tx1) { - dp83902a_start_xmit(dp->tx1, dp->tx1_len); - dp->tx_int = 1; - } else if (dp->tx2) { - dp83902a_start_xmit(dp->tx2, dp->tx2_len); - dp->tx_int = 2; - } else { - dp->tx_int = 0; - } - /* Tell higher level we sent this packet */ - uboot_push_tx_done(key, 0); -} - -/* - * Read the tally counters to clear them. Called in response to a CNT - * interrupt. - */ -static void -dp83902a_ClearCounters(void) -{ - struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - u8 *base = dp->base; - u8 cnt1, cnt2, cnt3; - - DP_IN(base, DP_FER, cnt1); - DP_IN(base, DP_CER, cnt2); - DP_IN(base, DP_MISSED, cnt3); - DP_OUT(base, DP_ISR, DP_ISR_CNT); -} - -/* - * Deal with an overflow condition. This code follows the procedure set - * out in section 7.0 of the datasheet. - */ -static void -dp83902a_Overflow(void) -{ - struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *)&nic; - u8 *base = dp->base; - u8 isr; - - /* Issue a stop command and wait 1.6ms for it to complete. */ - DP_OUT(base, DP_CR, DP_CR_STOP | DP_CR_NODMA); - CYGACC_CALL_IF_DELAY_US(1600); - - /* Clear the remote byte counter registers. */ - DP_OUT(base, DP_RBCL, 0); - DP_OUT(base, DP_RBCH, 0); - - /* Enter loopback mode while we clear the buffer. */ - DP_OUT(base, DP_TCR, DP_TCR_LOCAL); - DP_OUT(base, DP_CR, DP_CR_START | DP_CR_NODMA); - - /* - * Read in as many packets as we can and acknowledge any and receive - * interrupts. Since the buffer has overflowed, a receive event of - * some kind will have occured. - */ - dp83902a_RxEvent(); - DP_OUT(base, DP_ISR, DP_ISR_RxP|DP_ISR_RxE); - - /* Clear the overflow condition and leave loopback mode. */ - DP_OUT(base, DP_ISR, DP_ISR_OFLW); - DP_OUT(base, DP_TCR, DP_TCR_NORMAL); - - /* - * If a transmit command was issued, but no transmit event has occured, - * restart it here. - */ - DP_IN(base, DP_ISR, isr); - if (dp->tx_started && !(isr & (DP_ISR_TxP|DP_ISR_TxE))) { - DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_TXPKT | DP_CR_START); - } -} - -static void -dp83902a_poll(void) -{ - struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; - u8 *base = dp->base; - u8 isr; - - DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE0 | DP_CR_START); - DP_IN(base, DP_ISR, isr); - while (0 != isr) { - /* - * The CNT interrupt triggers when the MSB of one of the error - * counters is set. We don't much care about these counters, but - * we should read their values to reset them. - */ - if (isr & DP_ISR_CNT) { - dp83902a_ClearCounters(); - } - /* - * Check for overflow. It's a special case, since there's a - * particular procedure that must be followed to get back into - * a running state.a - */ - if (isr & DP_ISR_OFLW) { - dp83902a_Overflow(); - } else { - /* - * Other kinds of interrupts can be acknowledged simply by - * clearing the relevant bits of the ISR. Do that now, then - * handle the interrupts we care about. - */ - DP_OUT(base, DP_ISR, isr); /* Clear set bits */ - if (!dp->running) break; /* Is this necessary? */ - /* - * Check for tx_started on TX event since these may happen - * spuriously it seems. - */ - if (isr & (DP_ISR_TxP|DP_ISR_TxE) && dp->tx_started) { - dp83902a_TxEvent(); - } - if (isr & (DP_ISR_RxP|DP_ISR_RxE)) { - dp83902a_RxEvent(); - } - } - DP_IN(base, DP_ISR, isr); - } -} - +#define mdelay(n) udelay((n)*1000) /* find prom (taken from pc_net_cs.c from Linux) */ #include "8390.h" @@ -763,18 +174,16 @@ static hw_info_t hw_info[] = { #define PCNET_RESET 0x1f /* Issue a read to reset, a write to clear. */ #define PCNET_MISC 0x18 /* For IBM CCAE and Socket EA cards */ -static void pcnet_reset_8390(void) +static void pcnet_reset_8390(u8* addr) { int i, r; - PRINTK("nic base is %lx\n", nic.base); - n2k_outb(E8390_NODMA + E8390_PAGE0+E8390_STOP, E8390_CMD); - PRINTK("cmd (at %lx) is %x\n", nic.base + E8390_CMD, n2k_inb(E8390_CMD)); + PRINTK("cmd (at %lx) is %x\n", addr + E8390_CMD, n2k_inb(E8390_CMD)); n2k_outb(E8390_NODMA+E8390_PAGE1+E8390_STOP, E8390_CMD); - PRINTK("cmd (at %lx) is %x\n", nic.base + E8390_CMD, n2k_inb(E8390_CMD)); + PRINTK("cmd (at %lx) is %x\n", addr + E8390_CMD, n2k_inb(E8390_CMD)); n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); - PRINTK("cmd (at %lx) is %x\n", nic.base + E8390_CMD, n2k_inb(E8390_CMD)); + PRINTK("cmd (at %lx) is %x\n", addr + E8390_CMD, n2k_inb(E8390_CMD)); n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); n2k_outb(n2k_inb(PCNET_RESET), PCNET_RESET); @@ -791,8 +200,7 @@ static void pcnet_reset_8390(void) printf("pcnet_reset_8390() did not complete.\n"); } /* pcnet_reset_8390 */ -int get_prom(u8* mac_addr) __attribute__ ((weak, alias ("__get_prom"))); -int __get_prom(u8* mac_addr) +int get_prom(u8* mac_addr, u8* base_addr) { u8 prom[32]; int i, j; @@ -816,7 +224,7 @@ int __get_prom(u8* mac_addr) PRINTK ("trying to get MAC via prom reading\n"); - pcnet_reset_8390 (); + pcnet_reset_8390 (base_addr); mdelay (10); @@ -849,116 +257,3 @@ int __get_prom(u8* mac_addr) } return 0; } - -/* U-boot specific routines */ -static u8 *pbuf = NULL; - -static int pkey = -1; -static int initialized = 0; - -void uboot_push_packet_len(int len) { - PRINTK("pushed len = %d\n", len); - if (len >= 2000) { - printf("NE2000: packet too big\n"); - return; - } - dp83902a_recv(&pbuf[0], len); - - /*Just pass it to the upper layer*/ - NetReceive(&pbuf[0], len); -} - -void uboot_push_tx_done(int key, int val) { - PRINTK("pushed key = %d\n", key); - pkey = key; -} - -int eth_init(bd_t *bd) { - int r; - u8 dev_addr[6]; - char ethaddr[20]; - - PRINTK("### eth_init\n"); - - if (!pbuf) { - pbuf = malloc(2000); - if (!pbuf) { - printf("Cannot allocate rx buffer\n"); - return -1; - } - } - -#ifdef CONFIG_DRIVER_NE2000_CCR - { - vu_char *p = (vu_char *) CONFIG_DRIVER_NE2000_CCR; - - PRINTK("CCR before is %x\n", *p); - *p = CONFIG_DRIVER_NE2000_VAL; - PRINTK("CCR after is %x\n", *p); - } -#endif - - nic.base = (u8 *) CONFIG_DRIVER_NE2000_BASE; - - r = get_prom(dev_addr); - if (!r) - return -1; - - sprintf (ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X", - dev_addr[0], dev_addr[1], - dev_addr[2], dev_addr[3], - dev_addr[4], dev_addr[5]) ; - PRINTK("Set environment from HW MAC addr = \"%s\"\n", ethaddr); - setenv ("ethaddr", ethaddr); - - nic.data = nic.base + DP_DATA; - nic.tx_buf1 = START_PG; - nic.tx_buf2 = START_PG2; - nic.rx_buf_start = RX_START; - nic.rx_buf_end = RX_END; - - if (dp83902a_init() == false) - return -1; - - dp83902a_start(dev_addr); - initialized = 1; - - return 0; -} - -void eth_halt() { - - PRINTK("### eth_halt\n"); - if(initialized) - dp83902a_stop(); - initialized = 0; -} - -int eth_rx() { - dp83902a_poll(); - return 1; -} - -int eth_send(volatile void *packet, int length) { - int tmo; - - PRINTK("### eth_send\n"); - - pkey = -1; - - dp83902a_send((u8 *) packet, length, 666); - tmo = get_timer (0) + TOUT * CFG_HZ; - while(1) { - dp83902a_poll(); - if (pkey != -1) { - PRINTK("Packet sucesfully sent\n"); - return 0; - } - if (get_timer (0) >= tmo) { - printf("transmission error (timoeut)\n"); - return 0; - } - - } - return 0; -} diff --git a/drivers/net/ne2000_base.c b/drivers/net/ne2000_base.c new file mode 100644 index 0000000..4a07708 --- /dev/null +++ b/drivers/net/ne2000_base.c @@ -0,0 +1,757 @@ +/* +Ported to U-Boot by Christian Pellegrin <chri(a)ascensit.com> + +Based on sources from the Linux kernel (pcnet_cs.c, 8390.h) and +eCOS(if_dp83902a.c, if_dp83902a.h). Both of these 2 wonderful world +are GPL, so this is, of course, GPL. + +========================================================================== + +dev/if_dp83902a.c + +Ethernet device driver for NS DP83902a ethernet controller + +========================================================================== +####ECOSGPLCOPYRIGHTBEGIN#### +------------------------------------------- +This file is part of eCos, the Embedded Configurable Operating System. +Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc. + +eCos is free software; you can redistribute it and/or modify it under +the terms of the GNU General Public License as published by the Free +Software Foundation; either version 2 or (at your option) any later version. + +eCos is distributed in the hope that it will be useful, but WITHOUT ANY +WARRANTY; without even the implied warranty of MERCHANTABILITY or +FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License +for more details. + +You should have received a copy of the GNU General Public License along +with eCos; if not, write to the Free Software Foundation, Inc., +59 Temple Place, Suite 330, Boston, MA 02111-1307 USA. + +As a special exception, if other files instantiate templates or use macros +or inline functions from this file, or you compile this file and link it +with other works to produce a work based on this file, this file does not +by itself cause the resulting work to be covered by the GNU General Public +License. However the source code for this file must still be made available +in accordance with section (3) of the GNU General Public License. + +This exception does not invalidate any other reasons why a work based on +this file might be covered by the GNU General Public License. + +Alternative licenses for eCos may be arranged by contacting Red Hat, Inc. +at http://sources.redhat.com/ecos/ecos-license/ +------------------------------------------- +####ECOSGPLCOPYRIGHTEND#### +####BSDCOPYRIGHTBEGIN#### + +------------------------------------------- + +Portions of this software may have been derived from OpenBSD or other sources, +and are covered by the appropriate copyright disclaimers included herein. + +------------------------------------------- + +####BSDCOPYRIGHTEND#### +========================================================================== +#####DESCRIPTIONBEGIN#### + +Author(s): gthomas +Contributors: gthomas, jskov, rsandifo +Date: 2001-06-13 +Purpose: +Description: + +FIXME: Will fail if pinged with large packets (1520 bytes) +Add promisc config +Add SNMP + +####DESCRIPTIONEND#### + +========================================================================== +*/ + +#include <common.h> +#include <command.h> +#include <net.h> +#include <malloc.h> + +#define mdelay(n) udelay((n)*1000) +/* forward definition of function used for the uboot interface */ +void uboot_push_packet_len(int len); +void uboot_push_tx_done(int key, int val); + +/* NE2000 base header file */ +#include "ne2000_base.h" + +#if defined(CONFIG_DRIVER_AX88796L) +/* AX88796L support */ +#include "ax88796.h" +#else +/* Basic NE2000 chip support */ +#include "ne2000.h" +#endif + +static dp83902a_priv_data_t nic; /* just one instance of the card supported */ + +static bool +dp83902a_init(void) +{ + dp83902a_priv_data_t *dp = &nic; + u8* base; +#if defined(NE2000_BASIC_INIT) + int i; +#endif + + DEBUG_FUNCTION(); + + base = dp->base; + if (!base) + return false; /* No device found */ + + DEBUG_LINE(); + +#if defined(NE2000_BASIC_INIT) + /* AX88796L doesn't need */ + /* Prepare ESA */ + DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE1); /* Select page 1 */ + /* Use the address from the serial EEPROM */ + for (i = 0; i < 6; i++) + DP_IN(base, DP_P1_PAR0+i, dp->esa[i]); + DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE0); /* Select page 0 */ + + printf("NE2000 - %s ESA: %02x:%02x:%02x:%02x:%02x:%02x\n", + "eeprom", + dp->esa[0], + dp->esa[1], + dp->esa[2], + dp->esa[3], + dp->esa[4], + dp->esa[5] ); + +#endif /* NE2000_BASIC_INIT */ + return true; +} + +static void +dp83902a_stop(void) +{ + dp83902a_priv_data_t *dp = &nic; + u8 *base = dp->base; + + DEBUG_FUNCTION(); + + DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_STOP); /* Brutal */ + DP_OUT(base, DP_ISR, 0xFF); /* Clear any pending interrupts */ + DP_OUT(base, DP_IMR, 0x00); /* Disable all interrupts */ + + dp->running = false; +} + +/* + * This function is called to "start up" the interface. It may be called + * multiple times, even when the hardware is already running. It will be + * called whenever something "hardware oriented" changes and should leave + * the hardware ready to send/receive packets. + */ +static void +dp83902a_start(u8 * enaddr) +{ + dp83902a_priv_data_t *dp = &nic; + u8 *base = dp->base; + int i; + + DEBUG_FUNCTION(); + + DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_STOP); /* Brutal */ + DP_OUT(base, DP_DCR, DP_DCR_INIT); + DP_OUT(base, DP_RBCH, 0); /* Remote byte count */ + DP_OUT(base, DP_RBCL, 0); + DP_OUT(base, DP_RCR, DP_RCR_MON); /* Accept no packets */ + DP_OUT(base, DP_TCR, DP_TCR_LOCAL); /* Transmitter [virtually] off */ + DP_OUT(base, DP_TPSR, dp->tx_buf1); /* Transmitter start page */ + dp->tx1 = dp->tx2 = 0; + dp->tx_next = dp->tx_buf1; + dp->tx_started = false; + dp->running = true; + DP_OUT(base, DP_PSTART, dp->rx_buf_start); /* Receive ring start page */ + DP_OUT(base, DP_BNDRY, dp->rx_buf_end - 1); /* Receive ring boundary */ + DP_OUT(base, DP_PSTOP, dp->rx_buf_end); /* Receive ring end page */ + dp->rx_next = dp->rx_buf_start - 1; + dp->running = true; + DP_OUT(base, DP_ISR, 0xFF); /* Clear any pending interrupts */ + DP_OUT(base, DP_IMR, DP_IMR_All); /* Enable all interrupts */ + DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE1 | DP_CR_STOP); /* Select page 1 */ + DP_OUT(base, DP_P1_CURP, dp->rx_buf_start); /* Current page - next free page for Rx */ + dp->running = true; + for (i = 0; i < ETHER_ADDR_LEN; i++) { + /* FIXME */ + /*((vu_short*)( base + ((DP_P1_PAR0 + i) * 2) + + * 0x1400)) = enaddr[i];*/ + DP_OUT(base, DP_P1_PAR0+i, enaddr[i]); + } + /* Enable and start device */ + DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START); + DP_OUT(base, DP_TCR, DP_TCR_NORMAL); /* Normal transmit operations */ + DP_OUT(base, DP_RCR, DP_RCR_AB); /* Accept broadcast, no errors, no multicast */ + dp->running = true; +} + +/* + * This routine is called to start the transmitter. It is split out from the + * data handling routine so it may be called either when data becomes first + * available or when an Tx interrupt occurs + */ + +static void +dp83902a_start_xmit(int start_page, int len) +{ + dp83902a_priv_data_t *dp = (dp83902a_priv_data_t *) &nic; + u8 *base = dp->base; + + DEBUG_FUNCTION(); + +#if DEBUG & 1 + printf("Tx pkt %d len %d\n", start_page, len); + if (dp->tx_started) + printf("TX already started?!?\n"); +#endif + + DP_OUT(base, DP_ISR, (DP_ISR_TxP | DP_ISR_TxE)); + DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START); + DP_OUT(base, DP_TBCL, len & 0xFF); + DP_OUT(base, DP_TBCH, len >> 8); + DP_OUT(base, DP_TPSR, start_page); + DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_TXPKT | DP_CR_START); + + dp->tx_started = true; +} + +/* + * This routine is called to send data to the hardware. It is known a-priori + * that there is free buffer space (dp->tx_next). + */ +static void +dp83902a_send(u8 *data, int total_len, u32 key) +{ + struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; + u8 *base = dp->base; + int len, start_page, pkt_len, i, isr; +#if DEBUG & 4 + int dx; +#endif + + DEBUG_FUNCTION(); + + len = pkt_len = total_len; + if (pkt_len < IEEE_8023_MIN_FRAME) + pkt_len = IEEE_8023_MIN_FRAME; + + start_page = dp->tx_next; + if (dp->tx_next == dp->tx_buf1) { + dp->tx1 = start_page; + dp->tx1_len = pkt_len; + dp->tx1_key = key; + dp->tx_next = dp->tx_buf2; + } else { + dp->tx2 = start_page; + dp->tx2_len = pkt_len; + dp->tx2_key = key; + dp->tx_next = dp->tx_buf1; + } + +#if DEBUG & 5 + printf("TX prep page %d len %d\n", start_page, pkt_len); +#endif + + DP_OUT(base, DP_ISR, DP_ISR_RDC); /* Clear end of DMA */ + { + /* + * Dummy read. The manual sez something slightly different, + * but the code is extended a bit to do what Hitachi's monitor + * does (i.e., also read data). + */ + + u16 tmp; + int len = 1; + + DP_OUT(base, DP_RSAL, 0x100 - len); + DP_OUT(base, DP_RSAH, (start_page - 1) & 0xff); + DP_OUT(base, DP_RBCL, len); + DP_OUT(base, DP_RBCH, 0); + DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_RDMA | DP_CR_START); + DP_IN_DATA(dp->data, tmp); + } + +#ifdef CYGHWR_NS_DP83902A_PLF_BROKEN_TX_DMA + /* + * Stall for a bit before continuing to work around random data + * corruption problems on some platforms. + */ + CYGACC_CALL_IF_DELAY_US(1); +#endif + + /* Send data to device buffer(s) */ + DP_OUT(base, DP_RSAL, 0); + DP_OUT(base, DP_RSAH, start_page); + DP_OUT(base, DP_RBCL, pkt_len & 0xFF); + DP_OUT(base, DP_RBCH, pkt_len >> 8); + DP_OUT(base, DP_CR, DP_CR_WDMA | DP_CR_START); + + /* Put data into buffer */ +#if DEBUG & 4 + printf(" sg buf %08lx len %08x\n ", (u32)data, len); + dx = 0; +#endif + while (len > 0) { +#if DEBUG & 4 + printf(" %02x", *data); + if (0 == (++dx % 16)) printf("\n "); +#endif + + DP_OUT_DATA(dp->data, *data++); + len--; + } +#if DEBUG & 4 + printf("\n"); +#endif + if (total_len < pkt_len) { +#if DEBUG & 4 + printf(" + %d bytes of padding\n", pkt_len - total_len); +#endif + /* Padding to 802.3 length was required */ + for (i = total_len; i < pkt_len;) { + i++; + DP_OUT_DATA(dp->data, 0); + } + } + +#ifdef CYGHWR_NS_DP83902A_PLF_BROKEN_TX_DMA + /* + * After last data write, delay for a bit before accessing the + * device again, or we may get random data corruption in the last + * datum (on some platforms). + */ + CYGACC_CALL_IF_DELAY_US(1); +#endif + + /* Wait for DMA to complete */ + do { + DP_IN(base, DP_ISR, isr); + } while ((isr & DP_ISR_RDC) == 0); + + /* Then disable DMA */ + DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START); + + /* Start transmit if not already going */ + if (!dp->tx_started) { + if (start_page == dp->tx1) { + dp->tx_int = 1; /* Expecting interrupt from BUF1 */ + } else { + dp->tx_int = 2; /* Expecting interrupt from BUF2 */ + } + dp83902a_start_xmit(start_page, pkt_len); + } +} + +/* + * This function is called when a packet has been received. It's job is + * to prepare to unload the packet from the hardware. Once the length of + * the packet is known, the upper layer of the driver can be told. When + * the upper layer is ready to unload the packet, the internal function + * 'dp83902a_recv' will be called to actually fetch it from the hardware. + */ +static void +dp83902a_RxEvent(void) +{ + struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; + u8 *base = dp->base; + u8 rsr; + u8 rcv_hdr[4]; + int i, len, pkt, cur; + + DEBUG_FUNCTION(); + + DP_IN(base, DP_RSR, rsr); + while (true) { + /* Read incoming packet header */ + DP_OUT(base, DP_CR, DP_CR_PAGE1 | DP_CR_NODMA | DP_CR_START); + DP_IN(base, DP_P1_CURP, cur); + DP_OUT(base, DP_P1_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START); + DP_IN(base, DP_BNDRY, pkt); + + pkt += 1; + if (pkt == dp->rx_buf_end) + pkt = dp->rx_buf_start; + + if (pkt == cur) { + break; + } + DP_OUT(base, DP_RBCL, sizeof(rcv_hdr)); + DP_OUT(base, DP_RBCH, 0); + DP_OUT(base, DP_RSAL, 0); + DP_OUT(base, DP_RSAH, pkt); + if (dp->rx_next == pkt) { + if (cur == dp->rx_buf_start) + DP_OUT(base, DP_BNDRY, dp->rx_buf_end - 1); + else + DP_OUT(base, DP_BNDRY, cur - 1); /* Update pointer */ + return; + } + dp->rx_next = pkt; + DP_OUT(base, DP_ISR, DP_ISR_RDC); /* Clear end of DMA */ + DP_OUT(base, DP_CR, DP_CR_RDMA | DP_CR_START); +#ifdef CYGHWR_NS_DP83902A_PLF_BROKEN_RX_DMA + CYGACC_CALL_IF_DELAY_US(10); +#endif + + /* read header (get data size)*/ + for (i = 0; i < sizeof(rcv_hdr);) { + DP_IN_DATA(dp->data, rcv_hdr[i++]); + } + +#if DEBUG & 5 + printf("rx hdr %02x %02x %02x %02x\n", + rcv_hdr[0], rcv_hdr[1], rcv_hdr[2], rcv_hdr[3]); +#endif + len = ((rcv_hdr[3] << 8) | rcv_hdr[2]) - sizeof(rcv_hdr); + + /* data read */ + uboot_push_packet_len(len); + + if (rcv_hdr[1] == dp->rx_buf_start) + DP_OUT(base, DP_BNDRY, dp->rx_buf_end - 1); + else + DP_OUT(base, DP_BNDRY, rcv_hdr[1] - 1); /* Update pointer */ + } +} + +/* + * This function is called as a result of the "eth_drv_recv()" call above. + * It's job is to actually fetch data for a packet from the hardware once + * memory buffers have been allocated for the packet. Note that the buffers + * may come in pieces, using a scatter-gather list. This allows for more + * efficient processing in the upper layers of the stack. + */ +static void +dp83902a_recv(u8 *data, int len) +{ + struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; + u8 *base = dp->base; + int i, mlen; + u8 saved_char = 0; + bool saved; +#if DEBUG & 4 + int dx; +#endif + + DEBUG_FUNCTION(); + +#if DEBUG & 5 + printf("Rx packet %d length %d\n", dp->rx_next, len); +#endif + + /* Read incoming packet data */ + DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START); + DP_OUT(base, DP_RBCL, len & 0xFF); + DP_OUT(base, DP_RBCH, len >> 8); + DP_OUT(base, DP_RSAL, 4); /* Past header */ + DP_OUT(base, DP_RSAH, dp->rx_next); + DP_OUT(base, DP_ISR, DP_ISR_RDC); /* Clear end of DMA */ + DP_OUT(base, DP_CR, DP_CR_RDMA | DP_CR_START); +#ifdef CYGHWR_NS_DP83902A_PLF_BROKEN_RX_DMA + CYGACC_CALL_IF_DELAY_US(10); +#endif + + saved = false; + for (i = 0; i < 1; i++) { + if (data) { + mlen = len; +#if DEBUG & 4 + printf(" sg buf %08lx len %08x \n", (u32) data, mlen); + dx = 0; +#endif + while (0 < mlen) { + /* Saved byte from previous loop? */ + if (saved) { + *data++ = saved_char; + mlen--; + saved = false; + continue; + } + + { + u8 tmp; + DP_IN_DATA(dp->data, tmp); +#if DEBUG & 4 + printf(" %02x", tmp); + if (0 == (++dx % 16)) printf("\n "); +#endif + *data++ = tmp;; + mlen--; + } + } +#if DEBUG & 4 + printf("\n"); +#endif + } + } +} + +static void +dp83902a_TxEvent(void) +{ + struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; + u8 *base = dp->base; + u8 tsr; + u32 key; + + DEBUG_FUNCTION(); + + DP_IN(base, DP_TSR, tsr); + if (dp->tx_int == 1) { + key = dp->tx1_key; + dp->tx1 = 0; + } else { + key = dp->tx2_key; + dp->tx2 = 0; + } + /* Start next packet if one is ready */ + dp->tx_started = false; + if (dp->tx1) { + dp83902a_start_xmit(dp->tx1, dp->tx1_len); + dp->tx_int = 1; + } else if (dp->tx2) { + dp83902a_start_xmit(dp->tx2, dp->tx2_len); + dp->tx_int = 2; + } else { + dp->tx_int = 0; + } + /* Tell higher level we sent this packet */ + uboot_push_tx_done(key, 0); +} + +/* + * Read the tally counters to clear them. Called in response to a CNT + * interrupt. + */ +static void +dp83902a_ClearCounters(void) +{ + struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; + u8 *base = dp->base; + u8 cnt1, cnt2, cnt3; + + DP_IN(base, DP_FER, cnt1); + DP_IN(base, DP_CER, cnt2); + DP_IN(base, DP_MISSED, cnt3); + DP_OUT(base, DP_ISR, DP_ISR_CNT); +} + +/* + * Deal with an overflow condition. This code follows the procedure set + * out in section 7.0 of the datasheet. + */ +static void +dp83902a_Overflow(void) +{ + struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *)&nic; + u8 *base = dp->base; + u8 isr; + + /* Issue a stop command and wait 1.6ms for it to complete. */ + DP_OUT(base, DP_CR, DP_CR_STOP | DP_CR_NODMA); + CYGACC_CALL_IF_DELAY_US(1600); + + /* Clear the remote byte counter registers. */ + DP_OUT(base, DP_RBCL, 0); + DP_OUT(base, DP_RBCH, 0); + + /* Enter loopback mode while we clear the buffer. */ + DP_OUT(base, DP_TCR, DP_TCR_LOCAL); + DP_OUT(base, DP_CR, DP_CR_START | DP_CR_NODMA); + + /* + * Read in as many packets as we can and acknowledge any and receive + * interrupts. Since the buffer has overflowed, a receive event of + * some kind will have occured. + */ + dp83902a_RxEvent(); + DP_OUT(base, DP_ISR, DP_ISR_RxP|DP_ISR_RxE); + + /* Clear the overflow condition and leave loopback mode. */ + DP_OUT(base, DP_ISR, DP_ISR_OFLW); + DP_OUT(base, DP_TCR, DP_TCR_NORMAL); + + /* + * If a transmit command was issued, but no transmit event has occured, + * restart it here. + */ + DP_IN(base, DP_ISR, isr); + if (dp->tx_started && !(isr & (DP_ISR_TxP|DP_ISR_TxE))) { + DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_TXPKT | DP_CR_START); + } +} + +static void +dp83902a_poll(void) +{ + struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic; + u8 *base = dp->base; + u8 isr; + + DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE0 | DP_CR_START); + DP_IN(base, DP_ISR, isr); + while (0 != isr) { + /* + * The CNT interrupt triggers when the MSB of one of the error + * counters is set. We don't much care about these counters, but + * we should read their values to reset them. + */ + if (isr & DP_ISR_CNT) { + dp83902a_ClearCounters(); + } + /* + * Check for overflow. It's a special case, since there's a + * particular procedure that must be followed to get back into + * a running state.a + */ + if (isr & DP_ISR_OFLW) { + dp83902a_Overflow(); + } else { + /* + * Other kinds of interrupts can be acknowledged simply by + * clearing the relevant bits of the ISR. Do that now, then + * handle the interrupts we care about. + */ + DP_OUT(base, DP_ISR, isr); /* Clear set bits */ + if (!dp->running) break; /* Is this necessary? */ + /* + * Check for tx_started on TX event since these may happen + * spuriously it seems. + */ + if (isr & (DP_ISR_TxP|DP_ISR_TxE) && dp->tx_started) { + dp83902a_TxEvent(); + } + if (isr & (DP_ISR_RxP|DP_ISR_RxE)) { + dp83902a_RxEvent(); + } + } + DP_IN(base, DP_ISR, isr); + } +} + + +/* U-boot specific routines */ +static u8 *pbuf = NULL; + +static int pkey = -1; +static int initialized = 0; + +void uboot_push_packet_len(int len) { + PRINTK("pushed len = %d\n", len); + if (len >= 2000) { + printf("NE2000: packet too big\n"); + return; + } + dp83902a_recv(&pbuf[0], len); + + /*Just pass it to the upper layer*/ + NetReceive(&pbuf[0], len); +} + +void uboot_push_tx_done(int key, int val) { + PRINTK("pushed key = %d\n", key); + pkey = key; +} + +int eth_init(bd_t *bd) { + int r; + u8 dev_addr[6]; + char ethaddr[20]; + + PRINTK("### eth_init\n"); + + if (!pbuf) { + pbuf = malloc(2000); + if (!pbuf) { + printf("Cannot allocate rx buffer\n"); + return -1; + } + } + +#ifdef CONFIG_DRIVER_NE2000_CCR + { + vu_char *p = (vu_char *) CONFIG_DRIVER_NE2000_CCR; + + PRINTK("CCR before is %x\n", *p); + *p = CONFIG_DRIVER_NE2000_VAL; + PRINTK("CCR after is %x\n", *p); + } +#endif + + nic.base = (u8 *) CONFIG_DRIVER_NE2000_BASE; + + r = get_prom(dev_addr, nic.base); + if (!r) + return -1; + + sprintf (ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X", + dev_addr[0], dev_addr[1], + dev_addr[2], dev_addr[3], + dev_addr[4], dev_addr[5]) ; + PRINTK("Set environment from HW MAC addr = \"%s\"\n", ethaddr); + setenv ("ethaddr", ethaddr); + + nic.data = nic.base + DP_DATA; + nic.tx_buf1 = START_PG; + nic.tx_buf2 = START_PG2; + nic.rx_buf_start = RX_START; + nic.rx_buf_end = RX_END; + + if (dp83902a_init() == false) + return -1; + + dp83902a_start(dev_addr); + initialized = 1; + + return 0; +} + +void eth_halt() { + + PRINTK("### eth_halt\n"); + if(initialized) + dp83902a_stop(); + initialized = 0; +} + +int eth_rx() { + dp83902a_poll(); + return 1; +} + +int eth_send(volatile void *packet, int length) { + int tmo; + + PRINTK("### eth_send\n"); + + pkey = -1; + + dp83902a_send((u8 *) packet, length, 666); + tmo = get_timer (0) + TOUT * CFG_HZ; + while(1) { + dp83902a_poll(); + if (pkey != -1) { + PRINTK("Packet sucesfully sent\n"); + return 0; + } + if (get_timer (0) >= tmo) { + printf("transmission error (timoeut)\n"); + return 0; + } + + } + return 0; +} diff --git a/drivers/net/ne2000_base.h b/drivers/net/ne2000_base.h index 948b290..5446de4 100644 --- a/drivers/net/ne2000_base.h +++ b/drivers/net/ne2000_base.h @@ -80,10 +80,35 @@ are GPL, so this is, of course, GPL. #define __NE2000_BASE_H__ #define bool int - #define false 0 #define true 1 +/* + * Debugging details + * + * Set to perms of: + * 0 disables all debug output + * 1 for process debug output + * 2 for added data IO output: get_reg, put_reg + * 4 for packet allocation/free output + * 8 for only startup status, so we can tell we're installed OK + */ +#if 0 +#define DEBUG 0xf +#else +#define DEBUG 0 +#endif + +#if DEBUG & 1 +#define DEBUG_FUNCTION() do { printf("%s\n", __FUNCTION__); } while (0) +#define DEBUG_LINE() do { printf("%d\n", __LINE__); } while (0) +#define PRINTK(args...) printf(args) +#else +#define DEBUG_FUNCTION() do {} while(0) +#define DEBUG_LINE() do {} while(0) +#define PRINTK(args...) +#endif + /* timeout for tx/rx in s */ #define TOUT 5 /* Ether MAC address size */ @@ -119,11 +144,6 @@ typedef struct dp83902a_priv_data { int rx_buf_start, rx_buf_end; } dp83902a_priv_data_t; -/* - * Some forward declarations - */ -static void dp83902a_poll(void); - /* ------------------------------------------------------------------------ */ /* Register offsets */ @@ -281,4 +301,8 @@ static void dp83902a_poll(void); #define IEEE_8023_MAX_FRAME 1518 /* Largest possible ethernet frame */ #define IEEE_8023_MIN_FRAME 64 /* Smallest possible ethernet frame */ + +/* Functions */ +int get_prom(u8* mac_addr, u8* base_addr); + #endif /* __NE2000_BASE_H__ */ -- 1.5.6.3

4 5

[U-Boot] [UBoot] Hows to boot Linux Kernel from USB
by thaoth 03 Oct '08

03 Oct '08

Hi All, I would like to know how to boot linux kernel from USB. I have ported UBoot (support serial, USB driver) but didn't support CF card. Would you please tell me how to boot Linux Kernel from USB Flash memory? I have many guide could help hows to boot Linux kernel from CF card or network but I didn't see help for USB Flash memory. Here is step by step I did but didn't work. - First initialization USB => usb start - List file on USB Flash memory => fatls usb 0:1 3876248 vmlinux.srec 1348231 vmlinux 2207942 vmlinux.bin . 1277956 zimage - load zImage into SDRAM memory at base address 0x8c000000 + 200000 => fatload usb 0:1 200000 zimage reading zimage . . . . ................................................................................ ............................................ 1277956 bytes read => bootm Wrong Image Format for bootm command ERROR: can't get kernel image! This seems here is wrong command. I should load uImage (not zImage) into SDRAM memory. Google booting kernel from USB on the internet but I didn't see any help. :( Thank you for answer Best regards, -- View this message in context: http://www.nabble.com/-UBoot--Hows-to-boot-Linux-Kernel-from-USB-tp19740267… Sent from the Uboot - Users mailing list archive at Nabble.com.

6 17

[U-Boot] [patch 0/3] Improve stability USB memory sticks for the common OHCI USB layer.
by Remy Bohmer 02 Oct '08

02 Oct '08

This series is a set of patches that are required to make USB sticks behave robust while using U-Boot on a OHCI host. Several users complain about ERROR: CTL:TIMEOUT errors while using USB sticks, and while testing many different USB sticks it showed that some were working and many don't. It even showed a compiler dependency while debugging this, where GCC 3.x compilers seemed to work (but not always) and GCC 4.x compilers usually don't. While debugging this (with a USB analyser of course) it turned out that U-boot also made several protocol violations that needed to be solved, these resulted in hanging USB devices and so on. In a mail thread with Stelian Pop on 28 July it was reported of a known error on Atmel cores that it did not work. I tested these series on Atmel AT91SAM9261 Core, with the common OHCI driver, GCC 4.2.3 (Code Sourcery G++ Lite 2008q1-126) REMEMBER: U-boot still supports 1 single USB stick at a time... --

5 21

[U-Boot] [PATCH v3] Add support for KMC KZM-ARM11-01 board
by Atsuo Igarashi 01 Oct '08

01 Oct '08

This patch adds support for KMC KZM-ARM11-01 board. This board is configured with CFG_HZ=1000, so Signed-off-by: Atsuo Igarashi <atsuo_igarashi(a)tripeaks.co.jp>

2 2

Re: [U-Boot] Standalone Application Images support (bootm)
by Wolfgang Denk 01 Oct '08

01 Oct '08

Dear "Rodrigo Vilar", please keep the mailing list copied. In message <5fe3f7850809300849v22a0c987q83b4c8e5847482fb(a)mail.gmail.com> you wrote: > > > > Are "Standalone Applications" supported in the current u-boot (GIT repo)? > > > > Yes, of course. > > I am very happy to hear that. However the manual states "The bootm command > is used to start operating system images." and Standalone Applications were > supported on u-boot 1.2.0. Standalone Applications are no operating systems,m so "bootm" is the wrong command. Standalone Applications have been supported virtually forever. > > I recommend you start reading the documentation, especally the section > > about Standalone Applications. > > If you refer to chapter 5.12 I had already done so. It has been very useful > to download an run standalone applications however there is no reference on > how to do it with image files and bootm. That's because Standalone Applications don't use image files and bootm. They use the "go" command as documented in the manual. Is this so difficult? > appreciate the work you are doing with u-boot, however I also think you have > overlooked my questions. No, I haven't. If I tell you to read the documentation I am usually sure that the solution is theree. And the very first example (5.12.1. "Hello World" Demo) indeed shows how to run a SA application (not to mention that there is at least one relevant FAQ entry). Best regards, Wolfgang Denk -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd(a)denx.de When it is incorrect, it is, at least *authoritatively* incorrect. - Hitchiker's Guide To The Galaxy

2 2

[U-Boot] [PATCH 4/5] net: tsec: export tsec_info
by Anton Vorontsov 30 Sep '08

30 Sep '08

We'll need the exported tsec_info to fix up the phy addresses and tsecs' flags based on the hardware reset configuration words. Thus we'll use the tsec_info very early and just once at boot time, so network code won't notice it. Signed-off-by: Anton Vorontsov <avorontsov(a)ru.mvista.com> --- drivers/net/tsec.c | 2 +- include/tsec.h | 2 ++ 2 files changed, 3 insertions(+), 1 deletions(-) diff --git a/drivers/net/tsec.c b/drivers/net/tsec.c index 8ab6d07..1bca1b4 100644 --- a/drivers/net/tsec.c +++ b/drivers/net/tsec.c @@ -72,7 +72,7 @@ static int tsec_mcast_addr (struct eth_device *dev, u8 mcast_mac, u8 set); /* Default initializations for TSEC controllers. */ -static struct tsec_info_struct tsec_info[] = { +struct tsec_info_struct tsec_info[] = { #ifdef CONFIG_TSEC1 STD_TSEC_INFO(1), /* TSEC1 */ #endif diff --git a/include/tsec.h b/include/tsec.h index f7e5857..191bf1b 100644 --- a/include/tsec.h +++ b/include/tsec.h @@ -630,6 +630,8 @@ struct tsec_info_struct { u32 flags; }; +extern struct tsec_info_struct tsec_info[]; + int tsec_initialize(bd_t * bis, struct tsec_info_struct *tsec_info); int tsec_standard_init(bd_t *bis); int tsec_eth_init(bd_t *bis, struct tsec_info_struct *tsec_info, int num); -- 1.5.6.3

2 2

[U-Boot] [Fwd: Re: [U-Boot-Users] FIT-image with fdt doesn't work]
by Jon Loeliger 30 Sep '08

30 Sep '08

Gah. List foo. Sorry. -- jdl -------- Forwarded Message -------- From: Jon Loeliger <jdl(a)freescale.com> To: Simon Pasch <fpasch(a)googlemail.com> Cc: u-boot-users <u-boot-users(a)lists.sourceforge.net> Subject: Re: [U-Boot-Users] FIT-image with fdt doesn't work Date: Tue, 30 Sep 2008 10:37:50 -0500 On Tue, 2008-09-30 at 14:06 +0200, Simon Pasch wrote: > 3.) create a flat device tree blob (using dtc 1.2.0): > dtc -b 0 -V 17 -R 4 -S 0x3000 -I dts -O dtb -f devicetree.dts > target.dtb The -V 17 is the current default, so the option isn't needed. The -S 0x3000 may not be enough, and is really obsoleted but the -p <pad-value> option too. Try, oh, -p 0x1000 instead. If you have a large DTS or resulting DTB file, it might lead to problems like this: > 7.) try to boot it: > => bootm > ## Booting kernel from FIT Image at 00700000 ... > Using 'conf@1' configuration > Trying 'kernel@1' kernel subimage > Description: Vanilla Linux kernel > Type: Kernel Image > Compression: gzip compressed > Data Start: 0x007000ec > Data Size: 4052683 Bytes = 3.9 MB > Architecture: PowerPC > OS: Linux > Load Address: 0x00000000 > Entry Point: 0x00000000 > Hash algo: crc32 > Hash value: d4c2683b > Hash algo: sha1 > Hash value: 0f3c591c4f201d8cc1020725da0639d0b04d065a > Verifying Hash Integrity ... crc32+ sha1+ OK > Uncompressing Kernel Image ... OK > ## Flattened Device Tree from FIT Image at 00700000 > Using 'conf@1' configuration > Trying 'fdt@1' FDT blob subimage > Description: Flattened Device Tree blob > Type: Unknown Image > Compression: Unknown Compression > Data Start: 0x00add8e4 > Data Size: 12288 Bytes = 12 kB > Hash algo: crc32 > Hash value: e07e11d2 > Hash algo: sha1 > Hash value: 8ee8e8ce07508c534666f6d79fe89e46b8a7ae7a > Verifying Hash Integrity ... crc32+ sha1+ OK > ERROR: Not a FDT image - must RESET the board to recover. > > > As you can see the image-type of the fdt changed from "Flat Device > Tree" to "Unknown Image" after decompressing the kernel, but the hash > integrity seems to be fine (?!) > > What am I doing wrong? What's missing? Do some length analysis and make sure you are not stomping on any images in memory too, especially after uncompressing. jdl

1 0

[U-Boot] [PATCH 5/5] mpc83xx: add SGMII riser module support for the MPC8378E-MDS boards
by Anton Vorontsov 30 Sep '08

30 Sep '08

This involves configuring the SerDes and fixing up the flags and PHY addresses for the TSECs. For Linux we also fix up the device tree. Signed-off-by: Anton Vorontsov <avorontsov(a)ru.mvista.com> --- board/freescale/mpc837xemds/mpc837xemds.c | 117 +++++++++++++++++++++++++++++ include/configs/MPC837XEMDS.h | 2 + 2 files changed, 119 insertions(+), 0 deletions(-) diff --git a/board/freescale/mpc837xemds/mpc837xemds.c b/board/freescale/mpc837xemds/mpc837xemds.c index 581397d..3ee638b 100644 --- a/board/freescale/mpc837xemds/mpc837xemds.c +++ b/board/freescale/mpc837xemds/mpc837xemds.c @@ -15,6 +15,7 @@ #include <asm/io.h> #include <asm/fsl_serdes.h> #include <spd_sdram.h> +#include <tsec.h> #if defined(CONFIG_OF_LIBFDT) #include <libfdt.h> #endif @@ -44,6 +45,8 @@ int board_early_init_f(void) FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V); break; case SPR_8378: + fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SGMII, + FSL_SERDES_CLK_125, FSL_SERDES_VDD_1V); fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX, FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V); break; @@ -62,8 +65,121 @@ int board_early_init_f(void) return 0; } +#if defined(CONFIG_TSEC1) || defined(CONFIG_TSEC2) +static void board_tsec_fixup(void) +{ + struct immap __iomem *im = (struct immap __iomem *)CFG_IMMR; + u32 rcwh = in_be32(&im->reset.rcwh); + u32 tsec_mode; + int tsec_idx = 0; + +#ifdef CONFIG_TSEC1 + printf(CONFIG_TSEC1_NAME ": "); + + tsec_mode = rcwh & HRCWH_TSEC1M_MASK; + if (tsec_mode == HRCWH_TSEC1M_IN_RGMII) { + printf("RGMII\n"); + /* this is default, no need to fixup */ + } else if (tsec_mode == HRCWH_TSEC1M_IN_SGMII) { + printf("SGMII\n"); + tsec_info[tsec_idx].phyaddr = TSEC1_PHY_ADDR_SGMII; + tsec_info[tsec_idx].flags = TSEC_GIGABIT; + } else { + printf("unsupported PHY type\n"); + } + tsec_idx++; +#endif + +#ifdef CONFIG_TSEC2 + printf(CONFIG_TSEC2_NAME ": "); + + tsec_mode = rcwh & HRCWH_TSEC2M_MASK; + if (tsec_mode == HRCWH_TSEC2M_IN_RGMII) { + printf("RGMII\n"); + /* this is default, no need to fixup */ + } else if (tsec_mode == HRCWH_TSEC2M_IN_SGMII) { + printf("SGMII\n"); + tsec_info[tsec_idx].phyaddr = TSEC2_PHY_ADDR_SGMII; + tsec_info[tsec_idx].flags = TSEC_GIGABIT; + } else { + printf("unsupported PHY type\n"); + } +#endif +} + +static void __ft_tsec_fixup(void *blob, bd_t *bd, const char *alias, + int phy_addr) +{ + const char *phy_type = "sgmii"; + const u32 *ph; + int off; + int err; + + off = fdt_path_offset(blob, alias); + if (off < 0) { + printf("WARNING: could find %s alias: %s.\n", alias, + fdt_strerror(off)); + return; + } + + err = fdt_setprop(blob, off, "phy-connection-type", phy_type, + strlen(phy_type) + 1); + if (err) { + printf("WARNING: could not set phy-connection-type for %s: " + "%s.\n", alias, fdt_strerror(err)); + return; + } + + ph = (u32 *)fdt_getprop(blob, off, "phy-handle", 0); + if (!ph) { + printf("WARNING: could not get phy-handle for %s.\n", + alias); + return; + } + + off = fdt_node_offset_by_phandle(blob, *ph); + if (off < 0) { + printf("WARNING: could not get phy node for %s: %s\n", alias, + fdt_strerror(off)); + return; + } + + phy_addr = cpu_to_fdt32(phy_addr); + err = fdt_setprop(blob, off, "reg", &phy_addr, sizeof(phy_addr)); + if (err < 0) { + printf("WARNING: could not set phy node's reg for %s: " + "%s.\n", alias, fdt_strerror(err)); + return; + } +} + +static void ft_tsec_fixup(void *blob, bd_t *bd) +{ + struct immap __iomem *im = (struct immap __iomem *)CFG_IMMR; + u32 rcwh = in_be32(&im->reset.rcwh); + u32 tsec_mode; + +#ifdef CONFIG_TSEC1 + tsec_mode = rcwh & HRCWH_TSEC1M_MASK; + if (tsec_mode == HRCWH_TSEC1M_IN_SGMII) + __ft_tsec_fixup(blob, bd, "ethernet0", TSEC1_PHY_ADDR_SGMII); +#endif + +#ifdef CONFIG_TSEC2 + tsec_mode = rcwh & HRCWH_TSEC2M_MASK; + if (tsec_mode == HRCWH_TSEC2M_IN_SGMII) + __ft_tsec_fixup(blob, bd, "ethernet1", TSEC2_PHY_ADDR_SGMII); +#endif +} +#else +static inline void board_tsec_fixup(void) {} +static inline void ft_tsec_fixup(void *blob, bd_t *bd) {} +#endif /* defined(CONFIG_TSEC1) || defined(CONFIG_TSEC2) */ + int board_early_init_r(void) { + board_tsec_fixup(); + #ifdef CONFIG_PQ_MDS_PIB pib_init(); #endif @@ -152,6 +268,7 @@ int checkboard(void) void ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); + ft_tsec_fixup(blob, bd); #ifdef CONFIG_PCI ft_pci_setup(blob, bd); #endif diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index 7c87388..ed70b9e 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -381,6 +381,8 @@ #define CONFIG_TSEC2_NAME "eTSEC1" #define TSEC1_PHY_ADDR 2 #define TSEC2_PHY_ADDR 3 +#define TSEC1_PHY_ADDR_SGMII 8 +#define TSEC2_PHY_ADDR_SGMII 4 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -- 1.5.6.3

1 0

[U-Boot] [PATCH 3/5] mpc83xx: add TSECs' HRCWH masks for MPC837x processors
by Anton Vorontsov 30 Sep '08

30 Sep '08

We'll use these masks to parse TSEC modes out of HRCWH. Signed-off-by: Anton Vorontsov <avorontsov(a)ru.mvista.com> --- include/mpc83xx.h | 2 ++ 1 files changed, 2 insertions(+), 0 deletions(-) diff --git a/include/mpc83xx.h b/include/mpc83xx.h index 5d82bb4..ee38191 100644 --- a/include/mpc83xx.h +++ b/include/mpc83xx.h @@ -544,12 +544,14 @@ #define HRCWH_RL_EXT_LEGACY 0x00000000 #define HRCWH_RL_EXT_NAND 0x00040000 +#define HRCWH_TSEC1M_MASK 0x0000E000 #define HRCWH_TSEC1M_IN_MII 0x00000000 #define HRCWH_TSEC1M_IN_RMII 0x00002000 #define HRCWH_TSEC1M_IN_RGMII 0x00006000 #define HRCWH_TSEC1M_IN_RTBI 0x0000A000 #define HRCWH_TSEC1M_IN_SGMII 0x0000C000 +#define HRCWH_TSEC2M_MASK 0x00001C00 #define HRCWH_TSEC2M_IN_MII 0x00000000 #define HRCWH_TSEC2M_IN_RMII 0x00000400 #define HRCWH_TSEC2M_IN_RGMII 0x00000C00 -- 1.5.6.3

1 0

[U-Boot] [PATCH 2/5] mpc83xx: serdes: add forgotten shifts for rfcks
by Anton Vorontsov 30 Sep '08

30 Sep '08

The rfcks should be shifted by 28 bits left. We didn't notice the bug because we were using only 100MHz clocks (for which rfcks == 0). Though, for SGMII we'll need 125MHz clocks. Signed-off-by: Anton Vorontsov <avorontsov(a)ru.mvista.com> --- cpu/mpc83xx/serdes.c | 2 +- include/asm-ppc/fsl_serdes.h | 10 +++++----- 2 files changed, 6 insertions(+), 6 deletions(-) diff --git a/cpu/mpc83xx/serdes.c b/cpu/mpc83xx/serdes.c index 020c4c8..d1e0c97 100644 --- a/cpu/mpc83xx/serdes.c +++ b/cpu/mpc83xx/serdes.c @@ -42,7 +42,7 @@ #define FSL_SRDSRSTCTL_RST 0x80000000 #define FSL_SRDSRSTCTL_SATA_RESET 0xf -void fsl_setup_serdes(u32 offset, char proto, char rfcks, char vdd) +void fsl_setup_serdes(u32 offset, char proto, u32 rfcks, char vdd) { void *regs = (void *)CFG_IMMR + offset; u32 tmp; diff --git a/include/asm-ppc/fsl_serdes.h b/include/asm-ppc/fsl_serdes.h index 733f919..6da4b6f 100644 --- a/include/asm-ppc/fsl_serdes.h +++ b/include/asm-ppc/fsl_serdes.h @@ -3,9 +3,9 @@ #include <config.h> -#define FSL_SERDES_CLK_100 0 -#define FSL_SERDES_CLK_125 1 -#define FSL_SERDES_CLK_150 3 +#define FSL_SERDES_CLK_100 (0 << 28) +#define FSL_SERDES_CLK_125 (1 << 28) +#define FSL_SERDES_CLK_150 (3 << 28) #define FSL_SERDES_PROTO_SATA 0 #define FSL_SERDES_PROTO_PEX 1 #define FSL_SERDES_PROTO_PEX_X2 2 @@ -13,9 +13,9 @@ #define FSL_SERDES_VDD_1V 1 #ifdef CONFIG_FSL_SERDES -extern void fsl_setup_serdes(u32 offset, char proto, char rfcks, char vdd); +extern void fsl_setup_serdes(u32 offset, char proto, u32 rfcks, char vdd); #else -static void fsl_setup_serdes(u32 offset, char proto, char rfcks, char vdd) {} +static void fsl_setup_serdes(u32 offset, char proto, u32 rfcks, char vdd) {} #endif /* CONFIG_FSL_SERDES */ #endif /* __FSL_SERDES_H */ -- 1.5.6.3

1 0