June 2008 - U-Boot

[U-Boot-Users] [PATCH] ppc4xx: Unify AMCC's board config files (part 3/3)
by Stefan Roese 06 Jun '08

06 Jun '08

This patch series unifies the AMCC eval board ports by introducing a common include header for all AMCC eval boards: include/configs/amcc-common.h This header now includes all common configuration options/defines which are removed from the board specific headers. The reason for this is ease of maintenance and unified look and feel of all AMCC boards. Signed-off-by: Stefan Roese <sr(a)denx.de> --- board/amcc/sequoia/config.mk | 4 + include/configs/ocotea.h | 151 +++--------------------------------- include/configs/sequoia.h | 173 ++++------------------------------------- include/configs/taihu.h | 146 ++++-------------------------------- include/configs/taishan.h | 160 ++++----------------------------------- include/configs/walnut.h | 155 ++++---------------------------------- include/configs/yosemite.h | 164 ++++------------------------------------ include/configs/yucca.h | 151 +++--------------------------------- 8 files changed, 105 insertions(+), 999 deletions(-) diff --git a/board/amcc/sequoia/config.mk b/board/amcc/sequoia/config.mk index e62b8d3..5e04ee4 100644 --- a/board/amcc/sequoia/config.mk +++ b/board/amcc/sequoia/config.mk @@ -28,6 +28,10 @@ sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp ifndef TEXT_BASE TEXT_BASE = 0xFFFA0000 +# +# When defining CONFIG_VIDEO, TEXT_BASE needs to be 0xFFF80000 +# TEXT_BASE = 0xFFF80000 +# endif PLATFORM_CPPFLAGS += -DCONFIG_440=1 diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h index 1ec7a25..407aae7 100644 --- a/include/configs/ocotea.h +++ b/include/configs/ocotea.h @@ -46,13 +46,17 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME ocotea +#include "amcc-common.h" + /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xff800000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ #define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ @@ -74,18 +78,11 @@ #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) #define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ - /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */ -#define CONFIG_BAUDRATE 115200 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * Environment @@ -155,10 +152,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -167,54 +161,17 @@ #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=ocotea\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/ocotea/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fff00000\0" \ "ramdisk_addr=fff10000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/ocotea/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_NET_MULTI 1 #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_PHY1_ADDR 2 #define CONFIG_PHY2_ADDR 0x10 @@ -227,73 +184,15 @@ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_RESET_DELAY 1000 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- @@ -310,28 +209,4 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 48251f3..f4eefae 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -34,11 +34,19 @@ /* This config file is used for Sequoia (440EPx) and Rainier (440GRx) */ #ifndef CONFIG_RAINIER #define CONFIG_440EPX 1 /* Specific PPC440EPx */ +#define CONFIG_HOSTNAME sequoia #else #define CONFIG_440GRX 1 /* Specific PPC440GRx */ +#define CONFIG_HOSTNAME rainier #endif #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ + +/* + * Include common defines/options for all AMCC eval boards + */ +#include "amcc-common.h" + /* Detect Sequoia PLL input clock automatically via CPLD bit */ #define CONFIG_SYS_CLK_FREQ ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \ 33333333 : 33000000) @@ -64,19 +72,9 @@ * Base addresses -- Note these are effective addresses where the actual * resources get mapped (not physical addresses). */ -#ifndef CONFIG_VIDEO -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kiB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kiB for malloc() */ -#else -#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ -#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */ -#endif - #define CFG_TLB_FOR_BOOT_FLASH 0x0003 #define CFG_BOOT_BASE_ADDR 0xf0000000 -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ -#define CFG_MONITOR_BASE TEXT_BASE #define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */ #define CFG_OCM_BASE 0xe0010000 /* ocm */ #define CFG_OCM_DATA_ADDR CFG_OCM_BASE @@ -108,14 +106,9 @@ * Serial Port */ #define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /* * Environment */ @@ -227,10 +220,7 @@ /* * I2C */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -247,80 +237,27 @@ #define CFG_DTT_LOW_TEMP -30 #define CFG_DTT_HYSTERESIS 3 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#ifndef CONFIG_RAINIER -#define CONFIG_HOSTNAME sequoia -#define CFG_BOOTFILE "bootfile=sequoia/uImage\0" -#define CFG_DTBFILE "fdt_file=sequoia/sequoia.dtb\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" -#else -#define CONFIG_HOSTNAME rainier -#define CFG_BOOTFILE "bootfile=rainier/uImage\0" -#define CFG_DTBFILE "fdt_file=rainier/rainier.dtb\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" -#endif - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - CFG_BOOTFILE \ - CFG_ROOTPATH \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "addmisc=setenv bootargs ${bootargs}\0" \ - "flash_nfs=run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty addmisc;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};" \ - "run nfsargs addip addtty addmisc;" \ - "bootm\0" \ - "fdt_file=sequoia/sequoia.dtb\0" \ - "fdt_addr=400000\0" \ - "net_nfs_fdt=tftp 200000 ${bootfile};" \ - "tftp ${fdt_addr} ${fdt_file};" \ - "run nfsargs addip addtty addmisc;" \ - "bootm 200000 - ${fdt_addr}\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=FC000000\0" \ "ramdisk_addr=FC180000\0" \ - "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \ - "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \ - "cp.b 200000 FFFA0000 60000\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_M88E1111_PHY 1 #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_HAS_ETH0 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx */ - /* buffers & descriptors */ -#define CONFIG_NET_MULTI 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY1_ADDR 1 @@ -347,35 +284,12 @@ #define CONFIG_ISO_PARTITION /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP #define CONFIG_CMD_DTT -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF #define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII #define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #ifdef CONFIG_440EPX @@ -407,35 +321,6 @@ #define CONFIG_SUPPORT_VFAT /* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) - /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -/* * PCI stuff */ /* General PCI */ @@ -453,13 +338,6 @@ #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ /* - * For booting Linux, the board info and command line data have to be in the - * first 8 MB of memory, since this is the maximum mapped by the Linux kernel - * during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* * External Bus Controller (EBC) Setup */ @@ -577,23 +455,6 @@ } \ } -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #ifdef CONFIG_VIDEO #define CONFIG_BIOSEMU /* x86 bios emulator for vga bios */ #define CONFIG_ATI_RADEON_FB /* use radeon framebuffer driver */ diff --git a/include/configs/taihu.h b/include/configs/taihu.h index c060b1e..86f776d 100644 --- a/include/configs/taihu.h +++ b/include/configs/taihu.h @@ -32,6 +32,12 @@ #define CONFIG_4xx 1 /* member of PPC4xx family */ #define CONFIG_TAIHU 1 /* on a taihu board */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME taihu +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f */ #define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ @@ -70,87 +76,31 @@ #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS -#define CONFIG_EXTRA_ENV_SETTINGS \ - "bootfile=/tftpboot/taihu/uImage\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "netdev=eth0\0" \ - "hostname=taihu\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=FC000000\0" \ "ramdisk_addr=FC180000\0" \ - "load=tftp 200000 /tftpboot/taihu/u-boot.bin\0" \ - "update=protect off FFFC0000 FFFFFFFF;era FFFC0000 FFFFFFFF;" \ - "cp.b 200000 FFFC0000 40000\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0x14 /* PHY address */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_PHY1_ADDR 0x10 /* EMAC1 PHY address */ -#define CONFIG_NET_MULTI 1 -#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_PHY_RESET 1 /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_CACHE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SPI -#undef CONFIG_WATCHDOG /* watchdog disabled */ - #undef CONFIG_SPD_EEPROM /* use SPD EEPROM for setup */ #define CFG_SDRAM_SIZE_PER_BANK 0x04000000 /* 64MB */ #define CFG_SDRAM_BANKS 2 @@ -169,23 +119,6 @@ #define CFG_SDRAM_tRFC 66 /* Auto refresh period */ /* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. * If CFG_405_UART_ERRATA_59, then UART divisor is 31. * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. @@ -198,35 +131,13 @@ #undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ #undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CFG_BASE_BAUD 691200 - -#define CONFIG_BAUDRATE 115200 - #define CONFIG_UART1_CONSOLE 1 -/* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - /*----------------------------------------------------------------------- * I2C stuff *----------------------------------------------------------------------- */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ @@ -278,25 +189,12 @@ unsigned char spi_read(void); /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xFFE00000 -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ - #define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ @@ -421,21 +319,5 @@ unsigned char spi_read(void); #define CPLD_REG0_ADDR 0x50100000 #define CPLD_REG1_ADDR 0x50100001 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 #endif /* __CONFIG_H */ diff --git a/include/configs/taishan.h b/include/configs/taishan.h index 7b084cb..ba42192 100644 --- a/include/configs/taishan.h +++ b/include/configs/taishan.h @@ -34,6 +34,13 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME taishan +#define CONFIG_USE_TTY ttyS1 +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ @@ -41,9 +48,7 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ #define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ @@ -69,19 +74,11 @@ #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) #define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/ -#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc*/ - /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #define CONFIG_UART1_CONSOLE 1 /* use of UART1 as console */ -#define CONFIG_SERIAL_MULTI 1 /* enable serial multi support */ #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */ -#define CONFIG_BAUDRATE 115200 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * Environment @@ -137,10 +134,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #undef CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR 0x50 @@ -158,65 +152,23 @@ #define CFG_DTT_LOW_TEMP -30 #define CFG_DTT_HYSTERESIS 3 -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=taishan\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/taishan/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fc000000\0" \ "ramdisk_addr=fc180000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/taishan/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "fixedip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ - "$(gatewayip):$(netmask):$(hostname):$(netdev):off panic=1\0" \ - "dhcp=setenv bootargs $(bootargs) ip=dhcp\0" \ "kozio=bootm 0xffe00000\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /*----------------------------------------------------------------------- * Networking *----------------------------------------------------------------------*/ #define CONFIG_EMAC_NR_START 2 /* start with EMAC 2 (skip 0&1) */ -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_NET_MULTI 1 #define CONFIG_PHY_ADDR 0xff /* no phy on EMAC0 */ #define CONFIG_PHY1_ADDR 0xff /* no phy on EMAC1 */ #define CONFIG_PHY2_ADDR 0x1 @@ -229,70 +181,12 @@ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_RESET_DELAY 1000 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG #define CONFIG_CMD_DTT -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ /*----------------------------------------------------------------------- * PCI stuff @@ -311,28 +205,4 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/walnut.h b/include/configs/walnut.h index adc420b..e19c5f3 100644 --- a/include/configs/walnut.h +++ b/include/configs/walnut.h @@ -38,122 +38,44 @@ #define CONFIG_WALNUT 1 /* ...on a WALNUT board */ /* ...and on a SYCAMORE board */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME walnut +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=walnut\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/walnut/uImage\0" \ +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fff80000\0" \ "ramdisk_addr=fff80000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/walnut/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run net_nfs" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address */ - -#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ #define CONFIG_HAS_ETH0 1 -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* needed for NetConsole */ - #define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Walnut */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - #define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ /* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. * If CFG_405_UART_ERRATA_59, then UART divisor is 31. * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. @@ -167,29 +89,11 @@ #undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CFG_BASE_BAUD 691200 -/* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * I2C stuff *----------------------------------------------------------------------- */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -224,13 +128,8 @@ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xFFF80000 -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) /* * Define here the location of the environment variables (FLASH or NVRAM). @@ -243,13 +142,6 @@ #define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ #endif -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * FLASH organization */ @@ -335,21 +227,4 @@ */ #define SPD_EEPROM_ADDRESS 0x50 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index f22e798..891b515 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -42,6 +42,11 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ #define CONFIG_BOARD_RESET 1 /* call board_reset() */ @@ -50,10 +55,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ #define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 @@ -84,14 +85,9 @@ * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /*define this if you want console on UART1*/ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -142,10 +138,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -167,72 +160,22 @@ #define CFG_DTT_LOW_TEMP -30 #define CFG_DTT_HYSTERESIS 3 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#ifndef CONFIG_YELLOWSTONE -#define CONFIG_HOSTNAME yosemite -#define CFG_BOOTFILE "bootfile=/tftpboot/yosemite/uImage\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" -#else -#define CONFIG_HOSTNAME yellowstone -#define CFG_BOOTFILE "bootfile=/tftpboot/yellowstone/uImage\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" -#endif - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - CFG_BOOTFILE \ - CFG_ROOTPATH \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "bootfile=/tftpboot/${hostname}/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fc000000\0" \ "ramdisk_addr=fc180000\0" \ - "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \ - "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \ - "cp.b 200000 fff80000 80000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_NET_MULTI 1 /* required for netconsole */ -#define CONFIG_PHY1_ADDR 3 #define CONFIG_HAS_ETH0 1 /* add support for "ethaddr" */ #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ - -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ +#define CONFIG_PHY1_ADDR 3 /* Partitions */ #define CONFIG_MAC_PARTITION @@ -263,36 +206,11 @@ #define CONFIG_HW_WATCHDOG /* watchdog */ #endif - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG #define CONFIG_CMD_DTT -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SDRAM #ifdef CONFIG_440EP #define CONFIG_CMD_USB @@ -300,36 +218,6 @@ #define CONFIG_CMD_EXT2 #endif - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CONFIG_LYNXKDI 1 /* support kdi files */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- @@ -347,13 +235,6 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -370,21 +251,4 @@ #define CFG_BCSR5_PCI66EN 0x80 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/yucca.h b/include/configs/yucca.h index 9a0813f..026fef6 100644 --- a/include/configs/yucca.h +++ b/include/configs/yucca.h @@ -44,6 +44,12 @@ #define EXTCLK_50 50000000 #define EXTCLK_83 83333333 +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME yucca +#include "amcc-common.h" + #define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ #undef CONFIG_SHOW_BOOT_PROGRESS #undef CONFIG_STRESS @@ -52,9 +58,7 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffb0000 /* start of monitor */ #define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */ @@ -98,24 +102,15 @@ #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) #define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR -#define CFG_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Mon */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */ - /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CONFIG_SERIAL_MULTI 1 #undef CONFIG_UART1_CONSOLE #undef CONFIG_SERIAL_SOFTWARE_FIFO #undef CFG_EXT_SERIAL_CLOCK /* #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) */ /* Ext clk @ 11.059 MHz */ -#define CONFIG_BAUDRATE 115200 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ @@ -126,10 +121,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define IIC0_BOOTPROM_ADDR 0x50 #define IIC0_ALT_BOOTPROM_ADDR 0x54 @@ -152,123 +144,32 @@ #undef CFG_ENV_IS_IN_EEPROM /* ... not in EEPROM */ #define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=yucca\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=yucca/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=E7F10000\0" \ "ramdisk_addr=E7F20000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 yuca/u-boot.bin\0" \ - "update=protect off 2:4-7;era 2:4-7;" \ - "cp.b ${fileaddr} FFFB0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:EP:EP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM - #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ -#undef CONFIG_NET_MULTI #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_HAS_ETH0 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_RESET_DELAY 1000 #define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* needed for NetConsole */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ /*----------------------------------------------------------------------- * FLASH related @@ -317,26 +218,6 @@ /* Support for Intel 82557/82559/82559ER chips. */ #define CONFIG_EEPRO100 -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - /* FB Divisor selection */ #define FPGA_FB_DIV_6 6 #define FPGA_FB_DIV_10 10 @@ -538,10 +419,4 @@ #define PERIOD_33_33MHZ 30000 /* 30ns */ #define PERIOD_25_00MHZ 40000 /* 40ns */ -/*---------------------------------------------------------------------------*/ - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ -- 1.5.5.3

1 0

[U-Boot-Users] [PATCH] ppc4xx: Unify AMCC's board config files (part 2/3)
by Stefan Roese 06 Jun '08

06 Jun '08

This patch series unifies the AMCC eval board ports by introducing a common include header for all AMCC eval boards: include/configs/amcc-common.h This header now includes all common configuration options/defines which are removed from the board specific headers. The reason for this is ease of maintenance and unified look and feel of all AMCC boards. Signed-off-by: Stefan Roese <sr(a)denx.de> --- include/configs/acadia.h | 169 ++++------------------------------------ include/configs/bamboo.h | 168 +++++---------------------------------- include/configs/bubinga.h | 150 +++-------------------------------- include/configs/canyonlands.h | 173 ++++------------------------------------- include/configs/ebony.h | 151 ++++-------------------------------- include/configs/katmai.h | 162 ++++---------------------------------- include/configs/kilauea.h | 160 ++++---------------------------------- include/configs/luan.h | 147 ++++------------------------------- include/configs/makalu.h | 158 ++++---------------------------------- 9 files changed, 140 insertions(+), 1298 deletions(-) diff --git a/include/configs/acadia.h b/include/configs/acadia.h index bbf726d..9092a7c 100644 --- a/include/configs/acadia.h +++ b/include/configs/acadia.h @@ -34,6 +34,13 @@ #define CONFIG_ACADIA 1 /* Board is Acadia */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_405EZ 1 /* Specifc 405EZ support*/ + +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME acadia +#include "amcc-common.h" + /* Detect Acadia PLL input clock automatically via CPLD bit */ #define CONFIG_SYS_CLK_FREQ ((in8(CFG_CPLD_BASE + 0) == 0x0c) ? \ 66666666 : 33333000) @@ -59,16 +66,11 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xfe000000 #define CFG_CPLD_BASE 0x80000000 #define CFG_NAND_ADDR 0xd0000000 #define CFG_USB_HOST 0xef603000 /* USB OHCI 1.1 controller */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1) -#define CFG_MALLOC_LEN (512 * 1024)/* Reserve 512 kB for malloc() */ - /*----------------------------------------------------------------------- * Initial RAM & stack pointer *----------------------------------------------------------------------*/ @@ -89,12 +91,6 @@ *----------------------------------------------------------------------*/ #undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ #define CFG_BASE_BAUD 691200 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 - -/* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} /*----------------------------------------------------------------------- * Environment @@ -202,10 +198,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -222,77 +215,24 @@ #define CFG_DTT_LOW_TEMP -30 #define CFG_DTT_HYSTERESIS 3 -#if 0 /* test-only... */ -/*----------------------------------------------------------------------- - * SPI stuff - Define to include SPI control - *----------------------------------------------------------------------- - */ -#define CONFIG_SPI -#endif - /*----------------------------------------------------------------------- * Ethernet *----------------------------------------------------------------------*/ -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ -#define CONFIG_NET_MULTI 1 -#define CFG_RX_ETH_BUFFER 16 /* # of rx buffers & descriptors*/ #define CONFIG_HAS_ETH0 1 -#define CONFIG_NETCONSOLE /* include NetConsole support */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define xstr(s) str(s) -#define str(s) #s - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=acadia\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=acadia/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fff10000\0" \ "ramdisk_addr=fff20000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 acadia/u-boot.bin\0" \ - "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ - "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ - "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "nload=tftp 200000 acadia/u-boot-nand.bin\0" \ - "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \ - "setenv filesize;saveenv\0" \ - "nupd=run nload nupdate\0" \ "kozio=bootm ffc60000\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_USB_OHCI #define CONFIG_USB_STORAGE @@ -305,35 +245,10 @@ #define CONFIG_SUPPORT_VFAT /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP #define CONFIG_CMD_DTT -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII #define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_USB /* @@ -344,43 +259,6 @@ #undef CONFIG_CMD_IMLS #endif -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * NAND FLASH *----------------------------------------------------------------------*/ @@ -493,21 +371,4 @@ #define CFG_GPIO1_TSRL 0x00000000 #define CFG_GPIO1_TSRH 0x00000000 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) - #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ - #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index 8d77164..41058f8 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -36,6 +36,12 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME bamboo +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ /* @@ -49,10 +55,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */ #define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 @@ -84,14 +86,9 @@ * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * NVRAM/RTC * @@ -227,10 +224,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -244,54 +238,20 @@ #define CFG_ENV_OFFSET 0x0 #endif /* CFG_ENV_IS_IN_EEPROM */ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=bamboo\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/bamboo/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fff00000\0" \ "ramdisk_addr=fff10000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/bamboo/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b 100000 fffa0000 60000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_HAS_ETH0 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ #define CONFIG_PHY1_ADDR 1 @@ -299,16 +259,6 @@ #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #endif /* CONFIG_BAMBOO_NAND */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI 1 /* required for netconsole */ - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - #ifdef CONFIG_440EP /* USB */ #define CONFIG_USB_OHCI @@ -318,77 +268,27 @@ #define USB_2_0_DEVICE #endif /*CONFIG_440EP*/ - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM -#define CONFIG_CMD_USB -#define CONFIG_CMD_FAT -#define CONFIG_CMD_EXT2 #define CONFIG_CMD_SNTP +#define CONFIG_CMD_USB #ifdef CONFIG_BAMBOO_NAND #define CONFIG_CMD_NAND #endif - #define CONFIG_SUPPORT_VFAT -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CONFIG_LYNXKDI 1 /* support kdi files */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION /*----------------------------------------------------------------------- * PCI stuff @@ -407,28 +307,4 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h index 75dd4e7..acce82f 100644 --- a/include/configs/bubinga.h +++ b/include/configs/bubinga.h @@ -37,6 +37,12 @@ #define CONFIG_4xx 1 /* ...member of PPC4xx family */ #define CONFIG_BUBINGA 1 /* ...on a BUBINGA board */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME bubinga +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ @@ -80,118 +86,35 @@ #define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ #endif -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=bubinga\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/bubinga/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fff80000\0" \ "ramdisk_addr=fff90000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/bubinga/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run net_nfs" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */ -#define CONFIG_NET_MULTI 1 -#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ #define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Bubinga */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_CACHE #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - #define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ /* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. * If CFG_405_UART_ERRATA_59, then UART divisor is 31. * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. @@ -205,29 +128,11 @@ #undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CFG_BASE_BAUD 691200 -/* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * I2C stuff *----------------------------------------------------------------------- */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ @@ -272,21 +177,9 @@ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_SRAM_BASE 0xFFF00000 #define CFG_FLASH_BASE 0xFFF80000 -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization @@ -423,21 +316,4 @@ #define FPGA_REG1_OFFB_FLASH 0x02 /* Off board flash */ #define FPGA_REG1_SRAM_BOOT 0x01 /* SRAM at 0xFFF80000 not Flash */ -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h index 3dd577a..ac2e5d9 100644 --- a/include/configs/canyonlands.h +++ b/include/configs/canyonlands.h @@ -30,12 +30,19 @@ /* This config file is used for Canyonlands (460EX) and Glacier (460GT) */ #ifndef CONFIG_CANYONLANDS #define CONFIG_460GT 1 /* Specific PPC460GT */ +#define CONFIG_HOSTNAME glacier #else #define CONFIG_460EX 1 /* Specific PPC460EX */ +#define CONFIG_HOSTNAME canyonlands #endif #define CONFIG_440 1 #define CONFIG_4xx 1 /* ... PPC4xx family */ +/* + * Include common defines/options for all AMCC eval boards + */ +#include "amcc-common.h" + #define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ @@ -47,8 +54,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ - #define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ #define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ #define CFG_PCI_TARGBASE CFG_PCI_MEMBASE @@ -86,10 +91,6 @@ #define CFG_AHB_BASE 0xE2000000 /* internal AHB peripherals */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc()*/ - /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in OCM) *----------------------------------------------------------------------*/ @@ -102,13 +103,8 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 #undef CONFIG_UART1_CONSOLE /* define this if you want console on UART1 */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -242,10 +238,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_SPEED 400000 /* I2C speed */ #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -270,7 +263,6 @@ * Ethernet *----------------------------------------------------------------------*/ #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ #define CONFIG_PHY1_ADDR 1 #define CONFIG_HAS_ETH0 @@ -282,14 +274,11 @@ #define CONFIG_HAS_ETH2 #define CONFIG_HAS_ETH3 #endif -#define CONFIG_NET_MULTI 1 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_PHY_DYNAMIC_ANEG 1 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - /*----------------------------------------------------------------------- * USB-OHCI *----------------------------------------------------------------------*/ @@ -305,104 +294,30 @@ #define CFG_USB_OHCI_MAX_ROOT_PORTS 15 #endif -/*----------------------------------------------------------------------- - * Default environment - *----------------------------------------------------------------------*/ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#ifdef CONFIG_CANYONLANDS -#define CONFIG_HOSTNAME canyonlands -#define CFG_BOOTFILE "bootfile=canyonlands/uImage\0" -#define CFG_DTBFILE "fdt_file=canyonlands/canyonlands.dtb\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" -#else -#define CONFIG_HOSTNAME glacier -#define CFG_BOOTFILE "bootfile=glacier/uImage\0" -#define CFG_DTBFILE "fdt_file=glacier/glacier.dtb\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" -#endif - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - CFG_BOOTFILE \ - CFG_DTBFILE \ - CFG_ROOTPATH \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ - "tftp ${fdt_addr_r} ${fdt_file}; " \ - "run nfsargs addip addtty;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "kernel_addr_r=400000\0" \ - "fdt_addr_r=800000\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fc000000\0" \ "fdt_addr=fc1e0000\0" \ "ramdisk_addr=fc200000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 ${hostname}/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b ${fileaddr} fffa0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "nload=tftp 200000 ${hostname}/u-boot-nand.bin\0" \ - "nupdate=nand erase 0 100000;nand write 200000 0 100000;" \ - "setenv filesize;saveenv\0" \ - "nupd=run nload nupdate\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP #define CONFIG_CMD_DTT -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII #define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM +#define CONFIG_CMD_SNTP #ifdef CONFIG_460EX #define CONFIG_CMD_EXT2 #define CONFIG_CMD_FAT @@ -415,41 +330,6 @@ #define CONFIG_ISO_PARTITION /*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - -#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " -#endif - -/*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------*/ /* General PCI */ @@ -465,21 +345,6 @@ #define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ #define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -671,8 +536,4 @@ } #endif -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/ebony.h b/include/configs/ebony.h index b41fa17..df444d8 100644 --- a/include/configs/ebony.h +++ b/include/configs/ebony.h @@ -38,6 +38,12 @@ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ /* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME ebony +#include "amcc-common.h" + +/* * Define here the location of the environment variables (FLASH or NVRAM). * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only * supported for backward compatibility. @@ -54,7 +60,6 @@ *----------------------------------------------------------------------*/ #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xff800000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ #define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ @@ -73,18 +78,11 @@ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ - /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */ -#define CONFIG_BAUDRATE 115200 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400} /*----------------------------------------------------------------------- * NVRAM/RTC @@ -140,10 +138,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -152,125 +147,31 @@ #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=ebony\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/ebony/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=ff800000\0" \ "ramdisk_addr=ff810000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/ebony/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 8 /* PHY address */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_PHY1_ADDR 9 /* EMAC1 PHY address */ -#define CONFIG_NET_MULTI 1 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- @@ -287,28 +188,4 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 3c81862..d3789bd 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -38,6 +38,13 @@ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_440SPE 1 /* Specifc SPe support */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ + +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME katmai +#include "amcc-common.h" #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ @@ -47,7 +54,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xff000000 /* start of FLASH */ #define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */ @@ -77,10 +83,6 @@ #define CFG_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1) -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */ - /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ @@ -97,12 +99,8 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CONFIG_SERIAL_MULTI 1 #undef CONFIG_UART1_CONSOLE #undef CFG_EXT_SERIAL_CLOCK -#define CONFIG_BAUDRATE 115200 -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * DDR SDRAM @@ -116,10 +114,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CONFIG_I2C_MULTI_BUS #define CONFIG_I2C_CMD_TREE @@ -171,139 +166,36 @@ *----------------------------------------------------------------------*/ #define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define xstr(s) str(s) -#define str(s) #s - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=katmai\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "net_nfs_fdt=tftp 200000 ${bootfile};" \ - "tftp ${fdt_addr} ${fdt_file};" \ - "run nfsargs addip addtty;" \ - "bootm 200000 - ${fdt_addr}\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=katmai/uImage\0" \ - "fdt_file=katmai/katmai.dtb\0" \ - "fdt_addr=400000\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fff10000\0" \ "ramdisk_addr=fff20000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 katmai/u-boot.bin\0" \ - "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ - "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ - "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "kozio=bootm ffc60000\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_DTT -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP #define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */ -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_HAS_ETH0 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_RESET_DELAY 1000 #define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* needed for NetConsole */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ /*----------------------------------------------------------------------- * FLASH related @@ -435,28 +327,4 @@ #define CFG_GPIO_TCR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF) #define CFG_GPIO_ODR 0 -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 205577f..9c1a3a4 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -39,6 +39,12 @@ #define CONFIG_405EX 1 /* Specifc 405EX support*/ #define CONFIG_SYS_CLK_FREQ 33333333 /* ext frequency to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME kilauea +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ #define CONFIG_BOARD_EMAC_COUNT @@ -47,14 +53,10 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xFC000000 #define CFG_NAND_ADDR 0xF8000000 #define CFG_FPGA_BASE 0xF0000000 #define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */ -#define CFG_MONITOR_BASE (TEXT_BASE) /*----------------------------------------------------------------------- * Initial RAM & Stack Pointer Configuration Options @@ -112,14 +114,9 @@ * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -273,9 +270,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ #define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ @@ -295,7 +290,6 @@ *----------------------------------------------------------------------*/ #define CONFIG_M88E1111_PHY 1 #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ @@ -303,102 +297,33 @@ #define CONFIG_HAS_ETH0 1 -#define CONFIG_NET_MULTI 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY1_ADDR 2 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "logversion=2\0" \ - "netdev=eth0\0" \ - "hostname=kilauea\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_self_old=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "flash_nfs_old=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \ - "run nfsargs addip addtty;bootm ${kernel_addr_r}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ - "tftp ${fdt_addr_r} ${fdt_file}; " \ - "run nfsargs addip addtty;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=kilauea/uImage\0" \ - "fdt_file=kilauea/kilauea.dtb\0" \ - "kernel_addr_r=400000\0" \ - "fdt_addr_r=800000\0" \ "kernel_addr=fc000000\0" \ "fdt_addr=fc1e0000\0" \ "ramdisk_addr=fc200000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 kilauea/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b ${fileaddr} fffa0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "nload=tftp 200000 kilauea/u-boot-nand.bin\0" \ - "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \ - "setenv filesize;saveenv\0" \ - "nupd=run nload nupdate\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_DTT -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ #define CONFIG_CMD_LOG -#define CONFIG_CMD_MII #define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SNTP /* POST support */ @@ -417,37 +342,6 @@ #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------*/ @@ -476,13 +370,6 @@ /* base address of inbound PCIe window */ #define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -556,19 +443,6 @@ } \ } -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - /*----------------------------------------------------------------------- * Some Kilauea stuff..., mainly fpga registers */ @@ -604,8 +478,4 @@ #define CFG_FPGA_USER_LED0 0x00000200 #define CFG_FPGA_USER_LED1 0x00000100 -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/luan.h b/include/configs/luan.h index 41999d3..805cc59 100644 --- a/include/configs/luan.h +++ b/include/configs/luan.h @@ -37,6 +37,12 @@ #define CONFIG_440 1 #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME luan +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ @@ -44,11 +50,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) -#define CFG_SDRAM_BASE 0x00000000 /* MUST be zero */ - #define CFG_LARGE_FLASH 0xffc00000 /* 4MB flash address CS0 */ #define CFG_SMALL_FLASH 0xff900000 /* 1MB flash address CS2 */ #define CFG_SRAM_BASE 0xff800000 /* 1MB SRAM address CS2 */ @@ -87,13 +88,8 @@ * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* external 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#undef CONFIG_SERIAL_MULTI #undef CONFIG_UART1_CONSOLE /* define if you want console on UART1 */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -138,10 +134,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -150,61 +143,22 @@ #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=luan\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath)\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs $(bootargs) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ - ":$(hostname):$(netdev):off panic=1\0" \ - "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm $(kernel_addr)\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm $(kernel_addr) $(ramdisk_addr)\0" \ - "net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/luan/uImage\0" \ +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fc000000\0" \ "ramdisk_addr=fc100000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/luan/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_HAS_ETH0 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 #define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* needed for NetConsole */ - #ifdef DEBUG #define CONFIG_PANIC_HANG #else @@ -212,60 +166,11 @@ #endif /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#undef CONFIG_LYNXKDI /* support kdi files */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- @@ -286,28 +191,4 @@ #endif -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/makalu.h b/include/configs/makalu.h index 566e611..65b240e 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -39,6 +39,13 @@ #define CONFIG_405EX 1 /* Specifc 405EX support*/ #define CONFIG_SYS_CLK_FREQ 33330000 /* ext frequency to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME makalu +#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0" +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ @@ -46,13 +53,9 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xFC000000 #define CFG_FPGA_BASE 0xF0000000 #define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */ -#define CFG_MONITOR_BASE (TEXT_BASE) /*----------------------------------------------------------------------- * Initial RAM & Stack Pointer Configuration Options @@ -110,14 +113,9 @@ * Serial Port *----------------------------------------------------------------------*/ #undef CFG_EXT_SERIAL_CLOCK /* no ext. clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -205,9 +203,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ #define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ @@ -227,7 +223,6 @@ *----------------------------------------------------------------------*/ #define CONFIG_M88E1111_PHY 1 #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 6 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ @@ -235,99 +230,31 @@ #define CONFIG_HAS_ETH0 1 -#define CONFIG_NET_MULTI 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY1_ADDR 0 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "logversion=2\0" \ - "netdev=eth0\0" \ - "hostname=makalu\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0" \ - "flash_self_old=run ramargs addip addtty addmisc;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "flash_self=run ramargs addip addtty addmisc;" \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "flash_nfs_old=run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr}\0" \ - "flash_nfs=run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \ - "run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr_r}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ - "tftp ${fdt_addr_r} ${fdt_file}; " \ - "run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=makalu/uImage\0" \ - "fdt_file=makalu/makalu.dtb\0" \ - "kernel_addr_r=400000\0" \ - "fdt_addr_r=800000\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fc000000\0" \ "fdt_addr=fc1e0000\0" \ "ramdisk_addr=fc200000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 makalu/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b ${fileaddr} fffa0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG #define CONFIG_CMD_DTT -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ #define CONFIG_CMD_LOG -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SNTP /* POST support */ @@ -346,37 +273,6 @@ #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------*/ @@ -405,13 +301,6 @@ /* base address of inbound PCIe window */ #define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -470,21 +359,4 @@ #define CFG_GPIO_PCIE_CLKREQ 27 #define CFG_GPIO_PCIE_WAKE 28 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ -- 1.5.5.3

1 0

[U-Boot-Users] [PATCH] ppc4xx: Unify AMCC's board config files (part 1/3)
by Stefan Roese 06 Jun '08

06 Jun '08

This patch series unifies the AMCC eval board ports by introducing a common include header for all AMCC eval boards: include/configs/amcc-common.h This header now includes all common configuration options/defines which are removed from the board specific headers. The reason for this is ease of maintenance and unified look and feel of all AMCC boards. Signed-off-by: Stefan Roese <sr(a)denx.de> --- include/configs/amcc-common.h | 259 +++++++++++++++++++++++++++++++++++++++++ 1 files changed, 259 insertions(+), 0 deletions(-) create mode 100644 include/configs/amcc-common.h diff --git a/include/configs/amcc-common.h b/include/configs/amcc-common.h new file mode 100644 index 0000000..1f27d78 --- /dev/null +++ b/include/configs/amcc-common.h @@ -0,0 +1,259 @@ +/* + * (C) Copyright 2008 + * Stefan Roese, DENX Software Engineering, sr(a)denx.de. + * + * Common configuration options for all AMCC boards + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __AMCC_COMMON_H +#define __AMCC_COMMON_H + +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_MONITOR_BASE TEXT_BASE /* Start of U-Boot */ +#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1) +#define CFG_MALLOC_LEN (1 << 20) /* Reserved for malloc */ + +/* + * UART + */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} + +/* + * I2C + */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CFG_I2C_SLAVE 0x7F + +/* + * Ethernet/EMAC/PHY + */ +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_NET_MULTI +#define CONFIG_NETCONSOLE /* include NetConsole support */ +#if defined(CONFIG_440) +#define CFG_RX_ETH_BUFFER 32 /* number of eth rx buffers */ +#else +#define CFG_RX_ETH_BUFFER 16 /* number of eth rx buffers */ +#endif + +/* + * Commands + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#if defined(CONFIG_440) +#define CONFIG_CMD_CACHE +#endif +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +/* + * Miscellaneous configurable options + */ +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING /* add command line history */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_LOOPW /* enable loopw command */ +#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE /* include version env variable */ +#define CFG_CONSOLE_INFO_QUIET /* don't print console @ startup*/ + +#define CFG_HUSH_PARSER /* Use the HUSH parser */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_SUBNETMASK + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Internal Definitions + */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP + +/* + * Booting and default environment + */ +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" +#define CONFIG_BOOTCOMMAND "run flash_self" + +/* + * Only very few boards have default console not on ttyS0 (like Taishan) + */ +#if !defined(CONFIG_USE_TTY) +#define CONFIG_USE_TTY ttyS0 +#endif + +/* + * Only some 4xx PPC's are equipped with an FPU + */ +#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \ + defined(CONFIG_460EX) || defined(CONFIG_460GT) +#define CONFIG_AMCC_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" +#else +#define CONFIG_AMCC_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" +#endif + +/* + * Only some boards need to extend the bootargs by some additional + * parameters (like Makalu) + */ +#if !defined(CONFIG_ADDMISC) +#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs}\0" +#endif + +#define xstr(s) str(s) +#define str(s) #s + +/* + * General common environment variables shared on all AMCC eval boards + */ +#define CONFIG_AMCC_DEF_ENV \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs}" \ + " console=" xstr(CONFIG_USE_TTY) ",${baudrate}\0" \ + CONFIG_ADDMISC \ + "initrd_high=30000000\0" \ + "kernel_addr_r=400000\0" \ + "fdt_addr_r=800000\0" \ + "hostname=" xstr(CONFIG_HOSTNAME) "\0" \ + "bootfile=" xstr(CONFIG_HOSTNAME) "/uImage\0" \ + CONFIG_AMCC_DEF_ENV_ROOTPATH + +/* + * Default environment for arch/powerpc booting + * for boards that are ported to arch/powerpc + */ +#define CONFIG_AMCC_DEF_ENV_POWERPC \ + "flash_self=run ramargs addip addtty addmisc;" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "flash_nfs=run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ + "tftp ${fdt_addr_r} ${fdt_file}; " \ + "run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "fdt_file=" xstr(CONFIG_HOSTNAME) "/" xstr(CONFIG_HOSTNAME) ".dtb\0" + +/* + * Default environment for arch/ppc booting, + * for boards that are not ported to arch/powerpc yet + */ +#define CONFIG_AMCC_DEF_ENV_PPC \ + "flash_self=run ramargs addip addtty addmisc;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "flash_nfs=run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ + "run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr_r}\0" + +/* + * Default environment for arch/ppc booting (old version), + * for boards that are ported to arch/ppc and arch/powerpc + */ +#define CONFIG_AMCC_DEF_ENV_PPC_OLD \ + "flash_self_old=run ramargs addip addtty addmisc;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "flash_nfs_old=run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr}\0" \ + "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \ + "run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr_r}\0" + +#define CONFIG_AMCC_DEF_ENV_NOR_UPD \ + "load=tftp 200000 " xstr(CONFIG_HOSTNAME) "/u-boot.bin\0" \ + "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ + "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ + "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \ + "setenv filesize;saveenv\0" \ + "upd=run load update\0" \ + +#define CONFIG_AMCC_DEF_ENV_NAND_UPD \ + "nload=tftp 200000 " xstr(CONFIG_HOSTNAME) "/u-boot-nand.bin\0" \ + "nupdate=nand erase 0 100000;nand write 200000 0 100000;" \ + "setenv filesize;saveenv\0" \ + "nupd=run nload nupdate\0" + +#endif /* __AMCC_COMMON_H */ -- 1.5.5.3

1 0

[U-Boot-Users] [PATCH V6] ARM: Add support for Lyrtech SFF-SDR board (ARM926EJS)
by Hugo Villeneuve 06 Jun '08

06 Jun '08

ARM: This patch adds support for the Lyrtech SFF-SDR board, based on the TI DaVinci architecture (ARM926EJS). Changes between V5 and V6: -New email address for contributor. -Init of EMIF-A CS3 address space to load FPGA. -Dynamic parsing of MAC address in EEPROM. -Add boot delay of 5 sec. -Use NFS for Linux boot command. -Add relocate flag for command history. Signed-off-by: Hugo Villeneuve <hugo.villeneuve(a)lyrtech.com> Signed-off-by: Philip Balister, OpenSDR <philip(a)opensdr.com> --- CREDITS | 5 + MAKEALL | 1 + Makefile | 3 + board/davinci/sffsdr/Makefile | 51 +++++++ board/davinci/sffsdr/board_init.S | 32 ++++ board/davinci/sffsdr/config.mk | 42 ++++++ board/davinci/sffsdr/sffsdr.c | 288 +++++++++++++++++++++++++++++++++++++ board/davinci/sffsdr/u-boot.lds | 52 +++++++ include/asm-arm/mach-types.h | 13 ++ include/configs/davinci_sffsdr.h | 177 +++++++++++++++++++++++ 10 files changed, 664 insertions(+), 0 deletions(-) diff --git a/CREDITS b/CREDITS index e84ef38..b855904 100644 --- a/CREDITS +++ b/CREDITS @@ -533,3 +533,8 @@ N: Timo Tuunainen E: timo.tuunainen(a)sysart.fi D: Support for Artila M-501 starter kit W: http://www.sysart.fi/ + +N: Philip Balister +E: philip(a)opensdr.com +D: Port to Lyrtech SFFSDR development board. +W: www.opensdr.com diff --git a/MAKEALL b/MAKEALL index 37b4334..f53ceec 100755 --- a/MAKEALL +++ b/MAKEALL @@ -496,6 +496,7 @@ LIST_ARM9=" \ voiceblue \ davinci_dvevm \ davinci_schmoogie \ + davinci_sffsdr \ davinci_sonata \ " diff --git a/Makefile b/Makefile index 6548f8e..05d90aa 100644 --- a/Makefile +++ b/Makefile @@ -2408,6 +2408,9 @@ davinci_dvevm_config : unconfig davinci_schmoogie_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm926ejs schmoogie davinci davinci +davinci_sffsdr_config : unconfig + @$(MKCONFIG) $(@:_config=) arm arm926ejs sffsdr davinci davinci + davinci_sonata_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm926ejs sonata davinci davinci diff --git a/board/davinci/sffsdr/Makefile b/board/davinci/sffsdr/Makefile new file mode 100644 index 0000000..4413b33 --- /dev/null +++ b/board/davinci/sffsdr/Makefile @@ -0,0 +1,51 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# Copyright (C) 2007 Sergey Kubushyn <ksi(a)koi8.net> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o +SOBJS := board_init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak *~ .depend + +######################################################################### +# This is for $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/davinci/sffsdr/board_init.S b/board/davinci/sffsdr/board_init.S new file mode 100644 index 0000000..84ecd96 --- /dev/null +++ b/board/davinci/sffsdr/board_init.S @@ -0,0 +1,32 @@ +/* + * Board-specific low level initialization code. Called at the very end + * of cpu/arm926ejs/davinci/lowlevel_init.S. Just returns if there is no + * initialization required. + * + * Copyright (C) 2007 Sergey Kubushyn <ksi(a)koi8.net> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> + +.globl dv_board_init +dv_board_init: + + mov pc, lr diff --git a/board/davinci/sffsdr/config.mk b/board/davinci/sffsdr/config.mk new file mode 100644 index 0000000..b1c4ead --- /dev/null +++ b/board/davinci/sffsdr/config.mk @@ -0,0 +1,42 @@ +# +# Lyrtech SFF SDR board (ARM926EJS) cpu +# +# (C) Copyright 2002 +# Gary Jennejohn, DENX Software Engineering, <gj(a)denx.de> +# David Mueller, ELSOFT AG, <d.mueller(a)elsoft.ch> +# +# Copyright (C) 2008 Lyrtech <www.lyrtech.com> +# Copyright (C) 2008 Philip Balister, OpenSDR <philip(a)opensdr.com> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA + +# +# SFF SDR board has 1 bank of 128 MB DDR RAM +# Physical Address: +# 8000'0000 to 87FF'FFFF +# +# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000 +# (mem base + reserved) +# +# Integrity kernel is expected to be at 8000'0000, entry 8000'00D0, +# up to 81FF'FFFF (uses up to 32 MB of memory for text, heap, etc). +# +# we load ourself to 8400'0000 to provide at least 32MB spacing +# between us and the Integrity kernel image +TEXT_BASE = 0x84000000 diff --git a/board/davinci/sffsdr/sffsdr.c b/board/davinci/sffsdr/sffsdr.c new file mode 100644 index 0000000..b84cec4 --- /dev/null +++ b/board/davinci/sffsdr/sffsdr.c @@ -0,0 +1,288 @@ +/* + * Copyright (C) 2007 Sergey Kubushyn <ksi(a)koi8.net> + * + * Copyright (C) 2008 Lyrtech <www.lyrtech.com> + * Copyright (C) 2008 Philip Balister, OpenSDR <philip(a)opensdr.com> + * + * Parts are shamelessly stolen from various TI sources, original copyright + * follows: + * + * Copyright (C) 2004 Texas Instruments. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <common.h> +#include <i2c.h> +#include <asm/arch/hardware.h> +#include <asm/arch/emac_defs.h> + +#define DAVINCI_A3CR (0x01E00014) /* EMIF-A CS3 config register. */ +#define DAVINCI_A3CR_VAL (0x3FFFFFFD) /* EMIF-A CS3 value for FPGA. */ + +#define INTEGRITY_SYSCFG_OFFSET 0x7E8 +#define INTEGRITY_CHECKWORD_OFFSET 0x7F8 +#define INTEGRITY_CHECKWORD_VALUE 0x10ADBEEF + +DECLARE_GLOBAL_DATA_PTR; + +extern void timer_init(void); +extern int eth_hw_init(void); +extern phy_t phy; + + +/* Works on Always On power domain only (no PD argument) */ +void lpsc_on(unsigned int id) +{ + dv_reg_p mdstat, mdctl; + + if (id >= DAVINCI_LPSC_GEM) + return; /* Don't work on DSP Power Domain */ + + mdstat = REG_P(PSC_MDSTAT_BASE + (id * 4)); + mdctl = REG_P(PSC_MDCTL_BASE + (id * 4)); + + while (REG(PSC_PTSTAT) & 0x01); + + if ((*mdstat & 0x1f) == 0x03) + return; /* Already on and enabled */ + + *mdctl |= 0x03; + + /* Special treatment for some modules as for sprue14 p.7.4.2 */ + switch (id) { + case DAVINCI_LPSC_VPSSSLV: + case DAVINCI_LPSC_EMAC: + case DAVINCI_LPSC_EMAC_WRAPPER: + case DAVINCI_LPSC_MDIO: + case DAVINCI_LPSC_USB: + case DAVINCI_LPSC_ATA: + case DAVINCI_LPSC_VLYNQ: + case DAVINCI_LPSC_UHPI: + case DAVINCI_LPSC_DDR_EMIF: + case DAVINCI_LPSC_AEMIF: + case DAVINCI_LPSC_MMC_SD: + case DAVINCI_LPSC_MEMSTICK: + case DAVINCI_LPSC_McBSP: + case DAVINCI_LPSC_GPIO: + *mdctl |= 0x200; + break; + } + + REG(PSC_PTCMD) = 0x01; + + while (REG(PSC_PTSTAT) & 0x03); + while ((*mdstat & 0x1f) != 0x03); /* Probably an overkill... */ +} + +void dsp_on(void) +{ + int i; + + if (REG(PSC_PDSTAT1) & 0x1f) + return; /* Already on */ + + REG(PSC_GBLCTL) |= 0x01; + REG(PSC_PDCTL1) |= 0x01; + REG(PSC_PDCTL1) &= ~0x100; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) |= 0x03; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) &= 0xfffffeff; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) |= 0x03; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) &= 0xfffffeff; + REG(PSC_PTCMD) = 0x02; + + for (i = 0; i < 100; i++) { + if (REG(PSC_EPCPR) & 0x02) + break; + } + + REG(PSC_CHP_SHRTSW) = 0x01; + REG(PSC_PDCTL1) |= 0x100; + REG(PSC_EPCCR) = 0x02; + + for (i = 0; i < 100; i++) { + if (!(REG(PSC_PTSTAT) & 0x02)) + break; + } + + REG(PSC_GBLCTL) &= ~0x1f; +} + +int board_init(void) +{ + /* arch number of the board */ + gd->bd->bi_arch_number = MACH_TYPE_SFFSDR; + + /* address of boot parameters */ + gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR; + + /* Workaround for TMS320DM6446 errata 1.3.22 */ + REG(PSC_SILVER_BULLET) = 0; + + /* Power on required peripherals */ + lpsc_on(DAVINCI_LPSC_EMAC); + lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER); + lpsc_on(DAVINCI_LPSC_MDIO); + lpsc_on(DAVINCI_LPSC_I2C); + lpsc_on(DAVINCI_LPSC_UART0); + lpsc_on(DAVINCI_LPSC_TIMER1); + lpsc_on(DAVINCI_LPSC_GPIO); + + /* Powerup the DSP */ + dsp_on(); + + /* Bringup UART0 out of reset */ + REG(UART0_PWREMU_MGMT) = 0x0000e003; + + /* Enable GIO3.3V cells used for EMAC */ + REG(VDD3P3V_PWDN) = 0; + + /* Enable UART0 MUX lines */ + REG(PINMUX1) |= 1; + + /* Enable EMAC and AEMIF pins */ + REG(PINMUX0) = 0x80000c1f; + + /* Enable I2C pin Mux */ + REG(PINMUX1) |= (1 << 7); + + /* Set the Bus Priority Register to appropriate value */ + REG(VBPR) = 0x20; + + timer_init(); + + return(0); +} + +/* Read ethernet MAC address from Integrity data structure inside EEPROM. */ +int read_mac_address(uint8_t *buf) +{ + u_int32_t value, mac[2], address; + + /* Read Integrity data structure checkword. */ + if (i2c_read(CFG_I2C_EEPROM_ADDR, INTEGRITY_CHECKWORD_OFFSET, + CFG_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4)) { + printf("Read from EEPROM @ 0x%02x failed\n", + CFG_I2C_EEPROM_ADDR); + return 1; + } + if (value != INTEGRITY_CHECKWORD_VALUE) + return 1; + + /* Read SYSCFG structure offset. */ + if (i2c_read(CFG_I2C_EEPROM_ADDR, INTEGRITY_SYSCFG_OFFSET, + CFG_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4)) { + printf("Read from EEPROM @ 0x%02x failed\n", + CFG_I2C_EEPROM_ADDR); + return 1; + } + address = 0x800 + (int) value; /* Address where SYSCFG structure + * is located. */ + + /* Read NET CONFIG structure offset. */ + if (i2c_read(CFG_I2C_EEPROM_ADDR, address, + CFG_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4)) { + printf("Read from EEPROM @ 0x%02x failed\n", + CFG_I2C_EEPROM_ADDR); + return 1; + } + address = 0x800 + (int) value; /* Address where NET CONFIG structure + * is located. */ + address += 12; /* Address where NET INTERFACE CONFIG structure + * is located. */ + + /* Read NET INTERFACE CONFIG 2 structure offset. */ + if (i2c_read(CFG_I2C_EEPROM_ADDR, address, + CFG_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4)) { + printf("Read from EEPROM @ 0x%02x failed\n", + CFG_I2C_EEPROM_ADDR); + return 1; + } + address = 0x800 + 16 + (int) value;/* Address where NET INTERFACE + * CONFIG 2 structure is located. */ + + /* Read MAC address. */ + if (i2c_read(CFG_I2C_EEPROM_ADDR, address, + CFG_I2C_EEPROM_ADDR_LEN, (uint8_t *) &mac[0], 8)) { + printf("Read from EEPROM @ 0x%02x failed\n", + CFG_I2C_EEPROM_ADDR); + return 1; + } + + buf[0] = mac[0] >> 24; + buf[1] = mac[0] >> 16; + buf[2] = mac[0] >> 8; + buf[3] = mac[0]; + buf[4] = mac[1] >> 24; + buf[5] = mac[1] >> 16; + + return 0; +} + +/* Platform dependent initialisation. */ +int misc_init_r(void) +{ + u_int8_t tmp[20], buf[10]; + int clk = 0; + + /* EMIF-A CS3 configuration for FPGA. */ + REG(DAVINCI_A3CR) = DAVINCI_A3CR_VAL; + + clk = ((REG(PLL2_PLLM) + 1) * 27) / ((REG(PLL2_DIV2) & 0x1f) + 1); + + printf("ARM Clock: %dMHz\n", ((REG(PLL1_PLLM) + 1) * 27) / 2); + printf("DDR Clock: %dMHz\n", (clk / 2)); + + /* Configure I2C switch (PCA9543) to enable channel 0. */ + tmp[0] = CFG_I2C_PCA9543_ENABLE_CH0; + if (i2c_write(CFG_I2C_PCA9543_ADDR, 0, + CFG_I2C_PCA9543_ADDR_LEN, tmp, 1)) + printf("Write to MUX @ 0x%02x failed\n", CFG_I2C_PCA9543_ADDR); + + /* Set Ethernet MAC address from EEPROM if available. */ + if (read_mac_address(buf) == 0) { + if ((buf[0] != 0xff) && (getenv("ethaddr") == NULL)) { + sprintf((char *)&tmp[0], + "%02x:%02x:%02x:%02x:%02x:%02x", + buf[0], buf[1], buf[2], buf[3], + buf[4], buf[5]); + setenv("ethaddr", (char *)&tmp[0]); + } + } + + if (!eth_hw_init()) { + printf("Ethernet init failed\n"); + } else { + printf("ETH PHY: %s\n", phy.name); + } + + /* For most DaVinci boards, U-Boot is copied in RAM by the UBL, + * so we are always in the relocated state. This is + * necessary for command history to work. */ + gd->flags |= GD_FLG_RELOC; + + return(0); +} + +int dram_init(void) +{ + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; + + return(0); +} diff --git a/board/davinci/sffsdr/u-boot.lds b/board/davinci/sffsdr/u-boot.lds new file mode 100644 index 0000000..a4fcd1a --- /dev/null +++ b/board/davinci/sffsdr/u-boot.lds @@ -0,0 +1,52 @@ +/* + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, <gj(a)denx.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + . = ALIGN(4); + .text : + { + cpu/arm926ejs/start.o (.text) + *(.text) + } + . = ALIGN(4); + .rodata : { *(.rodata) } + . = ALIGN(4); + .data : { *(.data) } + . = ALIGN(4); + .got : { *(.got) } + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss (NOLOAD) : { *(.bss) } + _end = .; +} diff --git a/include/asm-arm/mach-types.h b/include/asm-arm/mach-types.h index aaf2ea2..b347857 100644 --- a/include/asm-arm/mach-types.h +++ b/include/asm-arm/mach-types.h @@ -1595,6 +1595,7 @@ extern unsigned int __machine_arch_type; #define MACH_TYPE_P300 1602 #define MACH_TYPE_XDACOMET 1603 #define MACH_TYPE_DEXFLEX2 1604 +#define MACH_TYPE_SFFSDR 1657 #ifdef CONFIG_ARCH_EBSA110 # ifdef machine_arch_type @@ -16500,6 +16501,18 @@ extern unsigned int __machine_arch_type; # define machine_is_schmoogie() (0) #endif +#ifdef CONFIG_MACH_SFFSDR +# ifdef machine_arch_type +# undef machine_arch_type +# define machine_arch_type __machine_arch_type +# else +# define machine_arch_type MACH_TYPE_SFFSDR +# endif +# define machine_is_sffsdr() (machine_arch_type == MACH_TYPE_SFFSDR) +#else +# define machine_is_sffsdr() (0) +#endif + #ifdef CONFIG_MACH_AZTOOL # ifdef machine_arch_type # undef machine_arch_type diff --git a/include/configs/davinci_sffsdr.h b/include/configs/davinci_sffsdr.h new file mode 100644 index 0000000..af19916 --- /dev/null +++ b/include/configs/davinci_sffsdr.h @@ -0,0 +1,177 @@ +/* + * Copyright (C) 2007 Sergey Kubushyn <ksi(a)koi8.net> + * + * Copyright (C) 2008 Lyrtech <www.lyrtech.com> + * Copyright (C) 2008 Philip Balister, OpenSDR <philip(a)opensdr.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H +#include <asm/sizes.h> + +/*=======*/ +/* Board */ +/*=======*/ +#define SFFSDR +#define CFG_NAND_LARGEPAGE +#define CFG_USE_NAND +/*===================*/ +/* SoC Configuration */ +/*===================*/ +#define CONFIG_ARM926EJS /* arm926ejs CPU core */ +#define CONFIG_SYS_CLK_FREQ 297000000 /* Arm Clock frequency */ +#define CFG_TIMERBASE 0x01c21400 /* use timer 0 */ +#define CFG_HZ_CLOCK 27000000 /* Timer Input clock freq */ +#define CFG_HZ 1000 +/*==================================================*/ +/* EEPROM definitions for Atmel 24LC64 EEPROM chip */ +/*==================================================*/ +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_I2C_EEPROM_ADDR 0x50 +#define CFG_EEPROM_PAGE_WRITE_BITS 5 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 +/*=============*/ +/* Memory Info */ +/*=============*/ +#define CFG_MALLOC_LEN (0x10000 + 256*1024) /* malloc() len */ +#define CFG_GBL_DATA_SIZE 128 /* reserved for initial data */ +#define CFG_MEMTEST_START 0x80000000 /* memtest start address */ +#define CFG_MEMTEST_END 0x81000000 /* 16MB RAM test */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define CONFIG_STACKSIZE (256*1024) /* regular stack */ +#define PHYS_SDRAM_1 0x80000000 /* DDR Start */ +#define PHYS_SDRAM_1_SIZE 0x08000000 /* DDR size 128MB */ +#define DDR_4BANKS /* 4-bank DDR2 (128MB) */ +/*====================*/ +/* Serial Driver info */ +/*====================*/ +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 4 /* NS16550 register size */ +#define CFG_NS16550_COM1 0x01c20000 /* Base address of UART0 */ +#define CFG_NS16550_CLK 27000000 /* Input clock to NS16550 */ +#define CONFIG_CONS_INDEX 1 /* use UART0 for console */ +#define CONFIG_BAUDRATE 115200 /* Default baud rate */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +/*===================*/ +/* I2C Configuration */ +/*===================*/ +#define CONFIG_HARD_I2C +#define CONFIG_DRIVER_DAVINCI_I2C +#define CFG_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */ +#define CFG_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */ +/*==================================*/ +/* Network & Ethernet Configuration */ +/*==================================*/ +#define CONFIG_DRIVER_TI_EMAC +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_OVERWRITE_ETHADDR_ONCE +/*=====================*/ +/* Flash & Environment */ +/*=====================*/ +#undef CFG_ENV_IS_IN_FLASH +#define CFG_NO_FLASH +#define CFG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ +#define CFG_ENV_SECT_SIZE 2048 /* Env sector Size */ +#define CFG_ENV_SIZE SZ_128K +#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */ +#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */ +#define CFG_NAND_BASE 0x02000000 +#define CFG_NAND_HW_ECC +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_MAX_CHIPS 1 +#define CFG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ +/*=====================*/ +/* Board related stuff */ +/*=====================*/ +/*==========================================*/ +/* I2C switch definitions for PCA9543 chip. */ +/*==========================================*/ +#define CFG_I2C_PCA9543_ADDR 0x70 +#define CFG_I2C_PCA9543_ADDR_LEN 0 /* Single register. */ +#define CFG_I2C_PCA9543_ENABLE_CH0 0x01 /* Enable channel 0. */ +/*==============================*/ +/* U-Boot general configuration */ +/*==============================*/ +#undef CONFIG_USE_IRQ /* No IRQ/FIQ in U-Boot */ +#define CONFIG_MISC_INIT_R +#define CONFIG_BOOTDELAY 5 /* Autoboot after 5 seconds. */ +#define CONFIG_BOOTFILE "uImage" /* Boot file name */ +#define CFG_PROMPT "U-Boot > " /* Monitor Command Prompt */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_PBSIZE \ + (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* Print buffer size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_LOAD_ADDR 0x80700000 /* Default Linux kernel + * load address. */ +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, + * may be later */ +#define CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_CMDLINE_EDITING +#define CFG_LONGHELP +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC +/*===================*/ +/* Linux Information */ +/*===================*/ +#define LINUX_BOOT_PARAM_ADDR 0x80000100 +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_BOOTARGS \ + "mem=56M " \ + "console=ttyS0,115200n8 " \ + "root=/dev/nfs rw noinitrd ip=dhcp " \ + "nfsroot=${serverip}:/nfsroot/sffsdr " \ + "nwhwconf=device:eth0,hwaddr:${ethaddr}" +#define CONFIG_BOOTCOMMAND \ + "nand read 87A00000 100000 300000;" \ + "bootelf 87A00000" +/*=================*/ +/* U-Boot commands */ +/*=================*/ +#include <config_cmd_default.h> +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVES +#define CONFIG_CMD_NAND +#define CONFIG_CMD_EEPROM +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_SETGETDCR +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_IMLS +/*=======================*/ +/* KGDB support (if any) */ +/*=======================*/ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */ +#endif +#endif /* __CONFIG_H */

2 2

[U-Boot-Users] How to customize u-boot
by Frank Wei 06 Jun '08

06 Jun '08

Hello, I'm new to u-boot. How can I customize u-boot to only include minimum features (such as load the operating system, some basic initialize of hardware...). I see u-boot is quite big without getting rid of some unnecessary features/modules. Regards,

2 1

[U-Boot-Users] Does u-boot provide SCP or FTP feature?
by Frank Wei 06 Jun '08

06 Jun '08

Hello, I'm new to u-boot. I saw u-boot does have TFTP but does anybody know that SCP and/or FTP have also been included? Many thanks,

3 3

[U-Boot-Users] Loading from NAND using 'nboot' Periodically Fails Where 'nand read' Succeeds
by Grant Erickson 06 Jun '08

06 Jun '08

Before I jump in with the BDI and start debugging, has anyone else using 'nboot' and FIT images noticed that 'nboot' periodically fails where 'nand read.i' of the SAME region of NAND succeeds? => echo $bootaddr 800000 => echo $boot0 nboot ${bootaddr} 0 0 && setenv bootargs root=/dev/mtdblock9 && run addjffs2 addtty && bootm ${bootaddr} => run boot0 Loading from NAND 64MiB 3,3V 8-bit, offset 0x0 ** Bad FIT image format => nand read.i ${bootaddr} 0 400000 NAND read: device 0 offset 0x0, size 0x400000 Reading data from 0x3ffe00 -- 100% complete. 4194304 bytes read: OK => setenv bootargs root=/dev/mtdblock9 => run addjffs2 addtty => bootm ${bootaddr} ## Booting kernel from FIT Image at 00800000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage ... Using Haleakala machine description Linux version 2.6.25-rc3-00951-g6514352-dirty (gerickson@ubuntu-fusion) (gcc version 4.0.0 (DENX ELDK 4.1 4.0.0)) #2 Wed May 28 22:49:36 PDT 2008 Zone PFN ranges: DMA 0 -> 65536 Normal 65536 -> 65536 Movable zone start PFN for each node early_node_map[1] active PFN ranges ... This is using AMCC's Haleakala board with Samsung K9F1208U0B NAND, though I suspect that doesn't make any difference since nand read.i works fine. Regards, Grant

7 12

[U-Boot-Users] [PATCH] sh: Add support Renesas SH7763
by Nobuhiro Iwamatsu 06 Jun '08

06 Jun '08

Renesas SH7763 has 3 SCIF, MMC, LCDC, Ethernet and other. This patch supprts CPU register's header file. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro(a)renesas.com> --- include/asm-sh/cpu_sh4.h | 2 + include/asm-sh/cpu_sh7763.h | 51 +++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 53 insertions(+), 0 deletions(-) create mode 100644 include/asm-sh/cpu_sh7763.h diff --git a/include/asm-sh/cpu_sh4.h b/include/asm-sh/cpu_sh4.h index c200ba5..5a8a5a1 100644 --- a/include/asm-sh/cpu_sh4.h +++ b/include/asm-sh/cpu_sh4.h @@ -35,6 +35,8 @@ # include <asm/cpu_sh7750.h> #elif defined (CONFIG_CPU_SH7722) # include <asm/cpu_sh7722.h> +#elif defined (CONFIG_CPU_SH7763) +# include <asm/cpu_sh7763.h> #elif defined (CONFIG_CPU_SH7780) # include <asm/cpu_sh7780.h> #else diff --git a/include/asm-sh/cpu_sh7763.h b/include/asm-sh/cpu_sh7763.h new file mode 100644 index 0000000..78b456b --- /dev/null +++ b/include/asm-sh/cpu_sh7763.h @@ -0,0 +1,51 @@ +/* + * Copyright (C) 2008 Renesas Solutions Corp. + * Copyright (C) 2007,2008 Nobuhiro Iwamatsu + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef _ASM_CPU_SH7763_H_ +#define _ASM_CPU_SH7763_H_ + +/* CACHE */ +#define CACHE_OC_NUM_WAYS 1 +#define CCR 0xFF00001C +#define CCR_CACHE_INIT 0x0000090b + +/* SCIF */ +/* SCIF0 */ +#define SCIF0_BASE SCSMR0 +#define SCSMR0 0xFFE00000 + +/* SCIF1 */ +#define SCIF1_BASE SCSMR1 +#define SCSMR1 0xFFE08000 + +/* SCIF2 */ +#define SCIF2_BASE SCSMR2 +#define SCSMR2 0xFFE10000 + +/* Watchdog Timer */ +#define WTCNT WDTST +#define WDTST 0xFFCC0000 + +/* TMU */ +#define TSTR 0xFFD80004 +#define TCOR0 0xFFD80008 +#define TCNT0 0xFFD8000C +#define TCR0 0xFFD80010 + +#endif /* _ASM_CPU_SH7763_H_ */ -- 1.5.5.1

1 0

Re: [U-Boot-Users] LL_TEMAC on Avnet MiniModule-FX12
by llandre 06 Jun '08

06 Jun '08

> What repository are you working from? U-Boot 1.3.1 cloned last February. > What ML403 patch are you referencing? http://www.dave.eu/download/misc/mmfx12/ml403.patch This derives directly from this old patch that has been around since 2005: http://www.dave.eu/download/misc/mmfx12/4-ml403.2005-10-01.patch This patch has been applied by my colleague. Then I put my hands on repository and started working on MiniModule port. > I'm working on a ML403 board at the moment and would be willing to help > debug / share fixes for u-boot. Thanks for your availability. > I have just started looking at a u-boot port but have been working lots > with the 2.6 kernel (using the ACE support). We did the same. First we worked on the ML403, then we ported our project to MiniModule that will be the base for the final application. -- llandre DAVE Electronics System House - R&D Department web: http://www.dave.eu email: r&d2(a)dave-tech.it > -----Original Message----- > From: u-boot-users-bounces(a)lists.sourceforge.net > [mailto:u-boot-users-bounces@lists.sourceforge.net] On Behalf Of llandre > Sent: Thursday, June 05, 2008 12:15 AM > To: u-boot-users(a)lists.sourceforge.net > Subject: [U-Boot-Users] LL_TEMAC on Avnet MiniModule-FX12 > > Hi all, > > I ported U-Boot 1.3.1 on Avnet MiniModule-FX12 (the repository I'm > working with has been patched previously with ML403 patch). Here is my > first dirty patch: > > http://www.dave.eu/download/misc/mmfx12/mmfx12-0.8.3.patch > > U-Boot works fine and it boots correctly from flash, however ethernet > interface (LL_TEMAC) does not work. > For example, when I try to perform a TFTP download, the XEmac_PollSend > function never returns because the following loop never ends: > > /* > * Loop on the MAC's status to wait for the transmit to complete. The > * transmit status is in the FIFO when the XMIT_DONE bit is set. > */ > do { > IntrStatus = XIIF_V123B_READ_IISR(InstancePtr->BaseAddress); > } > while ((IntrStatus & XEM_EIR_XMIT_DONE_MASK) == 0); > > Please note that the FPGA bitstream is ok because the linux kernel works > fine and can mount root file system via NFS so I pretty sure something > is wrong in my U-Boot port. > > Anybody experienced similar problems? > > > TIA, > llandre > > DAVE Electronics System House - R&D Department > web: http://www.dave.eu > email: r&d2(a)dave-tech.it > > ------------------------------------------------------------------------ > - > Check out the new SourceForge.net Marketplace. > It's the best place to buy or sell services for just about anything Open > Source. > http://sourceforge.net/services/buy/index.php > _______________________________________________ > U-Boot-Users mailing list > U-Boot-Users(a)lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/u-boot-users > >

1 0

[U-Boot-Users] [PATCH] sh: SH7763 SCIF support
by Nobuhiro Iwamatsu 06 Jun '08

06 Jun '08

SH7763 has 3 SCIF channels. SCIF0 and 1 are same register constitution, but only SCIF2 is different. This patch work all SCIF channel. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro(a)renesas.com> --- drivers/serial/serial_sh.c | 128 +++++++++++++++++++++++++------------------- 1 files changed, 73 insertions(+), 55 deletions(-) diff --git a/drivers/serial/serial_sh.c b/drivers/serial/serial_sh.c index aa4ff35..0801ac4 100644 --- a/drivers/serial/serial_sh.c +++ b/drivers/serial/serial_sh.c @@ -26,6 +26,8 @@ #define SCIF_BASE SCIF0_BASE #elif defined (CONFIG_CONS_SCIF1) #define SCIF_BASE SCIF1_BASE +#elif defined (CONFIG_CONS_SCIF2) +#define SCIF_BASE SCIF2_BASE #else #error "Default SCIF doesn't set....." #endif @@ -36,17 +38,17 @@ #define SCSCR (vu_short *)(SCIF_BASE + 0x8) #define SCFCR (vu_short *)(SCIF_BASE + 0x18) #define SCFDR (vu_short *)(SCIF_BASE + 0x1C) -#ifdef CONFIG_CPU_SH7720 /* SH7720 specific */ -# define SCFSR (vu_short *)(SCIF_BASE + 0x14) /* SCSSR */ +#ifdef CONFIG_CPU_SH7720 /* SH7720 specific */ +# define SCFSR (vu_short *)(SCIF_BASE + 0x14) /* SCSSR */ # define SCFTDR (vu_char *)(SCIF_BASE + 0x20) # define SCFRDR (vu_char *)(SCIF_BASE + 0x24) #else # define SCFTDR (vu_char *)(SCIF_BASE + 0xC) -# define SCFSR (vu_short *)(SCIF_BASE + 0x10) +# define SCFSR (vu_short *)(SCIF_BASE + 0x10) # define SCFRDR (vu_char *)(SCIF_BASE + 0x14) #endif -#if defined(CONFIG_CPU_SH7780) || \ +#if defined(CONFIG_CPU_SH7780) || \ defined(CONFIG_CPU_SH7785) # define SCRFDR (vu_short *)(SCIF_BASE + 0x20) # define SCSPTR (vu_short *)(SCIF_BASE + 0x24) @@ -54,20 +56,34 @@ # define SCRER (vu_short *)(SCIF_BASE + 0x2C) # define LSR_ORER 1 # define FIFOLEVEL_MASK 0xFF +#elif defined(CONFIG_CPU_SH7763) +# if defined (CONFIG_CONS_SCIF2) +# define SCSPTR (vu_short *)(SCIF_BASE + 0x20) +# define SCLSR (vu_short *)(SCIF_BASE + 0x24) +# define LSR_ORER 1 +# define FIFOLEVEL_MASK 0x1F +# else +# define SCRFDR (vu_short *)(SCIF_BASE + 0x20) +# define SCSPTR (vu_short *)(SCIF_BASE + 0x24) +# define SCLSR (vu_short *)(SCIF_BASE + 0x28) +# define SCRER (vu_short *)(SCIF_BASE + 0x2C) +# define LSR_ORER 1 +# define FIFOLEVEL_MASK 0xFF +# endif #elif defined(CONFIG_CPU_SH7750) || \ defined(CONFIG_CPU_SH7751) || \ defined(CONFIG_CPU_SH7722) # define SCSPTR (vu_short *)(SCIF_BASE + 0x20) -# define SCLSR (vu_short *)(SCIF_BASE + 0x24) +# define SCLSR (vu_short *)(SCIF_BASE + 0x24) # define LSR_ORER 1 # define FIFOLEVEL_MASK 0x1F #elif defined(CONFIG_CPU_SH7720) -# define SCLSR (vu_short *)(SCIF_BASE + 0x24) +# define SCLSR (vu_short *)(SCIF_BASE + 0x24) # define LSR_ORER 0x0200 # define FIFOLEVEL_MASK 0x1F -#elif defined(CONFIG_CPU_SH7710) +#elif defined(CONFIG_CPU_SH7710) || \ defined(CONFIG_CPU_SH7712) -# define SCLSR SCFSR /* SCSSR */ +# define SCLSR SCFSR /* SCSSR */ # define LSR_ORER 1 # define FIFOLEVEL_MASK 0x1F #endif @@ -75,34 +91,34 @@ /* SCBRR register value setting */ #if defined(CONFIG_CPU_SH7720) # define SCBRR_VALUE(bps, clk) (((clk*2)+16*bps)/(32*bps)-1) -#else /* Generic SuperH */ +#else /* Generic SuperH */ # define SCBRR_VALUE(bps, clk) ((clk+16*bps)/(32*bps)-1) #endif -#define SCR_RE (1 << 4) -#define SCR_TE (1 << 5) -#define FCR_RFRST (1 << 1) /* RFCL */ -#define FCR_TFRST (1 << 2) /* TFCL */ -#define FSR_DR (1 << 0) -#define FSR_RDF (1 << 1) -#define FSR_FER (1 << 3) -#define FSR_BRK (1 << 4) -#define FSR_FER (1 << 3) -#define FSR_TEND (1 << 6) -#define FSR_ER (1 << 7) +#define SCR_RE (1 << 4) +#define SCR_TE (1 << 5) +#define FCR_RFRST (1 << 1) /* RFCL */ +#define FCR_TFRST (1 << 2) /* TFCL */ +#define FSR_DR (1 << 0) +#define FSR_RDF (1 << 1) +#define FSR_FER (1 << 3) +#define FSR_BRK (1 << 4) +#define FSR_FER (1 << 3) +#define FSR_TEND (1 << 6) +#define FSR_ER (1 << 7) /*----------------------------------------------------------------------*/ -void serial_setbrg (void) +void serial_setbrg(void) { DECLARE_GLOBAL_DATA_PTR; - *SCBRR = SCBRR_VALUE(gd->baudrate,CONFIG_SYS_CLK_FREQ); + *SCBRR = SCBRR_VALUE(gd->baudrate, CONFIG_SYS_CLK_FREQ); } -int serial_init (void) +int serial_init(void) { *SCSCR = (SCR_RE | SCR_TE); - *SCSMR = 0 ; + *SCSMR = 0; *SCSMR = 0; *SCFCR = (FCR_RFRST | FCR_TFRST); *SCFCR; @@ -112,21 +128,21 @@ int serial_init (void) return 0; } -static int serial_rx_fifo_level (void) +static int serial_rx_fifo_level(void) { -#if defined(CONFIG_SH4A) +#if defined(SCRFDR) return (*SCRFDR >> 0) & FIFOLEVEL_MASK; #else return (*SCFDR >> 0) & FIFOLEVEL_MASK; #endif } -void serial_raw_putc (const char c) +void serial_raw_putc(const char c) { unsigned int fsr_bits_to_clear; while (1) { - if (*SCFSR & FSR_TEND) { /* Tx fifo is empty */ + if (*SCFSR & FSR_TEND) { /* Tx fifo is empty */ fsr_bits_to_clear = FSR_TEND; break; } @@ -137,65 +153,67 @@ void serial_raw_putc (const char c) *SCFSR &= ~fsr_bits_to_clear; } -void serial_putc (const char c) +void serial_putc(const char c) { if (c == '\n') - serial_raw_putc ('\r'); - serial_raw_putc (c); + serial_raw_putc('\r'); + serial_raw_putc(c); } -void serial_puts (const char *s) +void serial_puts(const char *s) { char c; while ((c = *s++) != 0) - serial_putc (c); + serial_putc(c); } -int serial_tstc (void) +int serial_tstc(void) { - return serial_rx_fifo_level() ? 1 : 0; + return serial_rx_fifo_level()? 1 : 0; } -#define FSR_ERR_CLEAR 0x0063 -#define RDRF_CLEAR 0x00fc -void handle_error( void ){ +#define FSR_ERR_CLEAR 0x0063 +#define RDRF_CLEAR 0x00fc +void handle_error(void) +{ - (void)*SCFSR ; - *SCFSR = FSR_ERR_CLEAR ; - (void)*SCLSR ; - *SCLSR = 0x00 ; + (void)*SCFSR; + *SCFSR = FSR_ERR_CLEAR; + (void)*SCLSR; + *SCLSR = 0x00; } -int serial_getc_check( void ){ +int serial_getc_check(void) +{ unsigned short status; - status = *SCFSR ; + status = *SCFSR; - if (status & (FSR_FER | FSR_FER | FSR_ER | FSR_BRK)) + if (status & (FSR_FER | FSR_ER | FSR_BRK)) handle_error(); - if( *SCLSR & LSR_ORER ) + if (*SCLSR & LSR_ORER) handle_error(); - return (status & ( FSR_DR | FSR_RDF )); + return (status & (FSR_DR | FSR_RDF)); } -int serial_getc (void) +int serial_getc(void) { - unsigned short status ; + unsigned short status; char ch; - while(!serial_getc_check()); + while (!serial_getc_check()) ; ch = *SCFRDR; - status = *SCFSR ; + status = *SCFSR; - *SCFSR = RDRF_CLEAR ; + *SCFSR = RDRF_CLEAR; if (status & (FSR_FER | FSR_FER | FSR_ER | FSR_BRK)) handle_error(); - if( *SCLSR & LSR_ORER ) + if (*SCLSR & LSR_ORER) handle_error(); - return ch ; + return ch; } -#endif /* CFG_SCIF_CONSOLE */ +#endif /* CFG_SCIF_CONSOLE */ -- 1.5.5.1

1 0