May 2006 - U-Boot

[U-Boot-Users] PATCH: Add PLEB 2 to top-level makefile
by David Snowdon 20 Jun '06

20 Jun '06

Please find attached a patch to the top level Makefile and associated documentation to add support for the PLEB 2 board (which somehow got left out of the last patch). Modifies: Makefile README MAKEALL Regards, Dave.

2 1

[U-Boot-Users] NOTE: New MTD flash partitioning methods
by Wolfgang Denk 20 Jun '06

20 Jun '06

Hello everybody, especially board maintainers! I just comitted a bigger patch that implements a new "mtdparts" command and a common partition scheme that allows U-Boot and Linux to share the same idea about flash partitioning.. Old, obsolete and duplicated code was cleaned up and replaced by the new partitioning method. There are two possible approaches now: The first one is to define a single, static partition: #undef CONFIG_JFFS2_CMDLINE #define CONFIG_JFFS2_DEV "nor0" #define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF /* use whole device */ #define CONFIG_JFFS2_PART_SIZE 0x00100000 /* use 1MB */ #define CONFIG_JFFS2_PART_OFFSET 0x00000000 The second method is to use the "mtdparts" command line and dynamic partitioning: /* mtdparts command line support */ #define CONFIG_JFFS2_CMDLINE #define MTDIDS_DEFAULT "nor1=zuma-1,nor2=zuma-2" #define MTDPARTS_DEFAULT "mtdparts=zuma-1:-(jffs2),zuma-2:-(user)" Command line of course produces bigger images, and may be inappropriate for some targets, so by default it's off. The code was tested on the following targets: Alaska8220, CPCI4052, NC650, PPChamelion, incaip. Besides the above targets, there were several other targets affected, where necessary changes were made. However, no testing was done for those targets, only compilation was verified (for PPC, MIPS and ARM targets). Due to the lack of tool chain for NICOS and i386 I was not able to compile the following targets: ADNPESC1, DK1C20, DK1S10, sc520_cdp, sc520_spunk. Among the modified and not tested targets there is a group of targets which were implementing their custom multi-partition scheme. This was mostly duplicating jffs2_part_info() routine code. Introducing the new common scheme required removing this duplicated code, so those targets should be especially carefully tested by the board main- tainers. Target list that require special attention: xsengine, voiceblue, mx1fs2, MPC8260ADS, innokom and VoVPN-GW (JFFS2 is by default not compiled in) and especially SXNI855T where the jffs2_part_info() routine was doing some custom NAND read caching. Thanks. Best regards, Wolfgang Denk -- Software Engineering: Embedded and Realtime Systems, Embedded Linux Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd(a)denx.de If there was anything that depressed him more than his own cynicism, it was that quite often it still wasn't as cynical as real life. - Terry Pratchett, _Guards! Guards!_

2 2

[U-Boot-Users] PATCH - Add support for wrPPMC7xx/74xx boards
by Richard Danter 20 Jun '06

20 Jun '06

Please find attached my patch for the Wind River PPMC 7xx/74xx boards. It has been tested with an MPC750 (66MHz bus) and MPC7400 (100MHz bus). It adds ppmc7xx to the board directory. The following common files have been modified: cpu/74xx_7xx/cpu.c cpu/74xx_7xx/start.S CREDITS drivers/pci.c include/ns16550.h MAKEALL Makefile This is my first patch so please let me know if I have missed anything. Thanks Rich

2 1

[U-Boot-Users] [PATCH] Support for new board, gth2
by Thomas Lange 19 Jun '06

19 Jun '06

* Patch by Thomas Lange Aug 11 2005 - Add support for gth2 board Changes to common files: * common/cmd_ide.c Swap input data if GTH2 and Big endian * cpu/mips/au1x00_serial.c Call GTH2 log functions. Make sure watchdog is kicked * cpu/mips/cpu.c If gth2, hang during reset until hardware watchdog kicks in * include/asm-mips/au1x00.h Add GPIO definitions /Thomas

2 1

[U-Boot-Users] [PATCH] dbau1x00 corrections
by Thomas Lange 19 Jun '06

19 Jun '06

* Patch by Thomas Lange Aug 10 2005 - Fix dbau1x00 boards broken by dbau1550 patch PLL:s were not set for boards other than 1550. Flash CFI caused card to hang due to undefined CFG_FLASH_BANKS_LIST. Default boot is now bootp for cards other than 1550. /Thomas Index: board/dbau1x00/lowlevel_init.S =================================================================== RCS file: /cvsroot/u-boot/u-boot/board/dbau1x00/lowlevel_init.S,v retrieving revision 1.1 diff -p -u -r1.1 lowlevel_init.S --- board/dbau1x00/lowlevel_init.S 2 Apr 2005 23:52:28 -0000 1.1 +++ board/dbau1x00/lowlevel_init.S 10 Aug 2005 13:07:23 -0000 @@ -185,6 +185,8 @@ tlbloop: bne t0, t2, tlbloop nop +#endif /* CONFIG_DBAU1550 */ + /* First setup pll:s to make serial work ok */ /* We have a 12 MHz crystal */ li t0, SYS_CPUPLL @@ -205,6 +207,7 @@ tlbloop: sw t1, 0(t0) /* aux pll */ sync +#ifdef CONFIG_DBAU1550 /* Static memory controller */ /* RCE0 - can not change while fetching, do so from icache */ move t2, ra /* Store return address */ @@ -237,7 +240,7 @@ noCacheJump: sw t1, 0(t0) #else /* CONFIG_DBAU1550 */ li t0, MEM_STTIME0 - li t1, 0x00014C0F + li t1, 0x040181D7 sw t1, 0(t0) /* RCE0 AMD 29LV640M MirrorBit Flash */ Index: include/configs/dbau1x00.h =================================================================== RCS file: /cvsroot/u-boot/u-boot/include/configs/dbau1x00.h,v retrieving revision 1.4 diff -p -u -r1.4 dbau1x00.h --- include/configs/dbau1x00.h 9 Jan 2005 22:29:00 -0000 1.4 +++ include/configs/dbau1x00.h 10 Aug 2005 13:07:24 -0000 @@ -81,8 +81,7 @@ CFG_CMD_MII | CFG_CMD_RUN | CFG_CMD_BDI | CFG_CMD_BEDBUG | \ CFG_CMD_NFS | CFG_CMD_ELF | CFG_CMD_PCMCIA | CFG_CMD_I2C)) #else /* CONFIG_DBAU1550 */ -/* Boot from Compact flash partition 2 as default */ -#define CONFIG_BOOTCOMMAND "ide reset;disk 0x81000000 0:2;bootm" +#define CONFIG_BOOTCOMMAND "bootp;bootm" #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_IDE | CFG_CMD_DHCP | CFG_CMD_ELF) & \ ~(CFG_CMD_ENV | CFG_CMD_FAT | CFG_CMD_FLASH | CFG_CMD_FPGA | \ @@ -133,8 +132,6 @@ #define PHYS_FLASH_1 0xb8000000 /* Flash Bank #1 */ #define PHYS_FLASH_2 0xbc000000 /* Flash Bank #2 */ -#define CFG_FLASH_BANKS_LIST {PHYS_FLASH_1, PHYS_FLASH_2} - #else /* CONFIG_DBAU1550 */ #define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ @@ -145,6 +142,8 @@ #endif /* CONFIG_DBAU1550 */ +#define CFG_FLASH_BANKS_LIST {PHYS_FLASH_1, PHYS_FLASH_2} + #define CFG_FLASH_CFI 1 #define CFG_FLASH_CFI_DRIVER 1

2 1

[U-Boot-Users] [patch] Bugfix in I2C initialisation on S3C2400
by Martin Krause 19 Jun '06

19 Jun '06

Bugfix in I2C initialisation on S3C2400. If the bus is blocked because of a previously interrupted transfer, on the I2CSCL line up to eleven clocks are generated to complete the transfer and to cause the hanging device to free the bus. With this fix pin I2CSCL (PG6) is really configured as GPIO and the clock pulses are really generated. Signed-off-by: Martin Krause <martin.krause(a)tqs.de> CHANGELOG: * Bugfix in I2C initialisation on S3C2400 Patch by Martin Krause, 4 Apr 2006

2 1

[U-Boot-Users] [patch] Fix DDR6 errata on TQM834x boards
by Martin Krause 19 Jun '06

19 Jun '06

This patch fixes the DDR6 errata (described in the document MPC8349E Device Errata Rev.8, 2/2006) on the TQM834x boards. Signed-off-by: Martin Krause <martin.krause(a)tqs.de> CHANGELOG: * Fix DDR6 errata on TQM834x boards Patch by Thomas Waehner, 7 Mar 2006

3 2

[U-Boot-Users] [patch] code-cleanup-for-tqm5200-board
by Martin Krause 19 Jun '06

19 Jun '06

Code cleanup for TQM5200 board. Signed-off-by: Martin Krause <martin.krause(a)tqs.de> This patch removes the obsolete flash driver /board/tqm5200/flash.c CHANGELOG: * Code cleanup for TQM5200 board. Patch by Martin Krause, 11 Jan 2006

2 1

RE: [U-Boot-Users] [PATCH] update-configuration-for-cmc-pu2-board.patch
by Martin Krause 19 Jun '06

19 Jun '06

wd(a)denx.de wrote on Wednesday, November 16, 2005 3:28 PM: > In message > <47F3F98010FF784EBEE6526EAAB078D1C05E9B(a)tq-mailsrv.tq-net.de> you > wrote: > > > > Update configuration for CMC-PU2 board > > Patch by Martin Krause, 16 Nov 2005 > > > > This configuration is in usage some time now. Only the patch hasn't > > been send since now.=20 > > I reject this patch. Please remove dead / unused code instead of > using "#if 0"; if you want it back you get it from the git / CVS > history. OK. Attached a cleaned version. Update configuration for CMC-PU2 board Patch by Martin Krause, 17 Nov 2005 This configuration is in usage some time now. Only the patch hasn't been send since now. Signed-off-by: Martin Krause <martin.krause(a)tqs.de> CHANGELOG: * Update configuration for CMC-PU2 board Patch by Martin Krause, 17 Nov 2005

2 1

[U-Boot-Users] [PATCH] Adjust TQM5200 make targets
by Martin Krause 19 Jun '06

19 Jun '06

Adjust TQM5200 make targets Patch by Martin Krause, 07 Nov 2005 Make the automatic CS configuration the default. The dedicated configurations CONFIG_TQM5200_AA, CONFIG_TQM5200_AB and CONFIG_TQM5200_AC are removed. "TQM5200_config" is now the default for STK52XX.200 base boards. On a STK52XX.100 base board "TQM5200_STK100_config" should be used. Signed-off-by: Martin Krause <martin.krause(a)tqs.de> CHANGELOG: * Adjust TQM5200 make targets Patch by Martin Krause 07 Nov 2005 ---

2 1