November 2005 - U-Boot

[U-Boot-Users] PATCH: RPXlite configuration fixes
by Yuli Barcohen 12 Mar '06

12 Mar '06

The attached patch fixes several bugs in and adds some features to long orphaned RPXlite port. CHANGELOG Fix RPXlite board configuration. - Use correct flash sector size - Use correct memory test end address - Add support for bzip2 compression - Various small fixes -- ======================================================================== Yuli Barcohen | Phone +972-9-765-1788 | Software Project Leader yuli(a)arabellasw.com | Fax +972-9-765-7494 | Arabella Software, Israel ========================================================================

3 16

[U-Boot-Users] PATCH: Numerous fixes for ZPC.1900 port
by Yuli Barcohen 12 Mar '06

12 Mar '06

The attached patch fixes memory configuration for Zephyr Engineering ZPC.1900 board. CHANGELOG Memory configuration changes for ZPC.1900 board - Fix SDRAM timing on both local bus and 60x bus - Add support for second flash bank (SIMM) - Change boot flash base -- ======================================================================== Yuli Barcohen | Phone +972-9-765-1788 | Software Project Leader yuli(a)arabellasw.com | Fax +972-9-765-7494 | Arabella Software, Israel ========================================================================

2 1

[U-Boot-Users] PATCH: Add support for Adder boards with 16MB SDRAM
by Yuli Barcohen 12 Mar '06

12 Mar '06

The attached patch adds support for Analogue&Micro Adder boards with 16MB SDRAM (current configuration supports 8MB only). Also, added support for second FEC on Adder87x board. CHANGELOG - Add support for Adder boards with 16MB SDRAM - Add support for second FEC on Adder87x board -- ======================================================================== Yuli Barcohen | Phone +972-9-765-1788 | Software Project Leader yuli(a)arabellasw.com | Fax +972-9-765-7494 | Arabella Software, Israel ========================================================================

2 1

[U-Boot-Users] [PATCH] include top config.mk only after CROSS_COMPILE is defined
by Friedrich Lobenstock 12 Mar '06

12 Mar '06

Hi Wolfgang! During compiling I just spotted the fact that gccincdir := $(shell $(CC) -print-file-name=include) in the top config.mk does execute "gcc -print-file-name=include" instead of "m68k-elf-gcc ..." which I would expect as i compile for m68k. I think that this does not make much difference as the includes should mostly be the same, but for the sake of completeness I want to bring the attached patch to your attention. Description of the patch: * CROSS_COMPILE is referenced in the top 'config.mk' file therefore we need to include it in the main Makefile only after CROSS_COMPILE is defined This patch is against the u-boot-1.1.2. -- MfG / Regards Friedrich Lobenstock --- u-boot-1.1.2-org/Makefile 2004-12-19 10:58:11.000000000 +0100 +++ u-boot-1.1.2/Makefile 2005-06-01 18:35:44.000000000 +0200 @@ -46,9 +46,6 @@ # load ARCH, BOARD, and CPU configuration include include/config.mk export ARCH CPU BOARD VENDOR SOC -# load other configuration -include $(TOPDIR)/config.mk - ifndef CROSS_COMPILE ifeq ($(HOSTARCH),ppc) CROSS_COMPILE = @@ -86,6 +83,10 @@ export CROSS_COMPILE +# load other configuration +include $(TOPDIR)/config.mk + + ######################################################################### # U-Boot objects....order is important (i.e. start must be first)

3 3

[U-Boot-Users] [PATCH] soft_i2c/i2c_probe(): Perform reads instead of writes
by Peter Korsgaard 12 Mar '06

12 Mar '06

Hi, The following little patch makes the i2c_probe function use reads instead of writes to match the comment (broken in r1.2). * Patch by Peter Korsgaard, 26 May 2005: Use reads instead of writes for probe in soft_i2c. -- Bye, Peter Korsgaard

4 6

[U-Boot-Users] [PATCH] add OpenGear CM4008 board support
by Greg Ungerer 12 Mar '06

12 Mar '06

Hi All, Attached is a patch that adds support to u-boot for the OpenGear CM4008 8 port console manager board. It is built around the KS8695P CPU, with 8 serial ports, 16MB RAM, and 8MB NOR flash. This patch was originally generated against u-boot 1.1.1. Regards Greg diff -Naur --exclude=CVS u-boot-1.1.1/board/cm4008/cm4008.c u-boot/board/cm4008/cm4008.c --- u-boot-1.1.1/board/cm4008/cm4008.c 1970-01-01 10:00:00.000000000 +1000 +++ u-boot/board/cm4008/cm4008.c 2005-05-04 22:47:00.021931928 +1000 @@ -0,0 +1,101 @@ +/* + * (C) Copyright 2005 + * Greg Ungerer, OpenGear Inc, <greg.ungerer(a)opengear.com> + * + * (C) Copyright 2002 + * Kyle Harris, Nexus Technologies, Inc. kharris(a)nexus-tech.net + * + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH <www.elinos.com> + * Marius Groeger <mgroeger(a)sysgo.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/arch/platform.h> + +/* ------------------------------------------------------------------------- */ + +#define ks8695_read(a) *((volatile unsigned int *) (KS8695_IO_BASE+(a))) +#define ks8695_write(a,b) *((volatile unsigned int *) (KS8695_IO_BASE+(a))) = (b) + +/* ------------------------------------------------------------------------- */ + + +/* + * Miscelaneous platform dependent initialisations + */ +int env_flash_cmdline (void) +{ + unsigned char *sp = (unsigned char *) 0x0201c020; + unsigned char *ep; + int len; + + /* Check if "erase" push button is depressed */ + if ((ks8695_read(KS8695_GPIO_DATA) & 0x8) == 0) { + printf("### Entering network recovery mode...\n"); + setenv("bootargs", "console=ttyAM0,115200 mem=16M initrd=0x400000,6M root=/dev/ram0"); + setenv("bootcmd", "bootp 0x400000; gofsk 0x400000"); + setenv("bootdelay", "2"); + return 0; + } + + /* Check for flash based kernel boot args to use as default */ + for (ep = sp, len = 0; ((len < 1024) && (*ep != 0)); ep++, len++) + ; + + if ((len > 0) && (len <1024)) + setenv("bootargs", sp); + + return 0; +} + +int board_late_init (void) +{ + return 0; +} + + +int board_init (void) +{ + DECLARE_GLOBAL_DATA_PTR; + + /* arch number of CM4008 */ + gd->bd->bi_arch_number = 624; + + /* adress of boot parameters */ + gd->bd->bi_boot_params = 0x00000100; + + /* power down all but port 0 on the switch */ + ks8695_write(KS8695_SWITCH_LPPM12, 0x00000005); + ks8695_write(KS8695_SWITCH_LPPM34, 0x00050005); + + return 0; +} + +int dram_init (void) +{ + DECLARE_GLOBAL_DATA_PTR; + + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; + + return (0); +} diff -Naur --exclude=CVS u-boot-1.1.1/board/cm4008/config.mk u-boot/board/cm4008/config.mk --- u-boot-1.1.1/board/cm4008/config.mk 1970-01-01 10:00:00.000000000 +1000 +++ u-boot/board/cm4008/config.mk 2005-01-11 00:56:42.000000000 +1000 @@ -0,0 +1 @@ +TEXT_BASE = 0x00f00000 diff -Naur --exclude=CVS u-boot-1.1.1/board/cm4008/flash.c u-boot/board/cm4008/flash.c --- u-boot-1.1.1/board/cm4008/flash.c 1970-01-01 10:00:00.000000000 +1000 +++ u-boot/board/cm4008/flash.c 2005-01-17 00:55:13.000000000 +1000 @@ -0,0 +1,409 @@ +/* + * (C) Copyright 2005 + * Greg Ungerer, OpenGear Inc, greg.ungerer(a)opengear.com + * + * (C) Copyright 2001 + * Kyle Harris, Nexus Technologies, Inc. kharris(a)nexus-tech.net + * + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <linux/byteorder/swab.h> + + +flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ + +#define mb() __asm__ __volatile__ ("" : : : "memory") + +/*----------------------------------------------------------------------- + * Functions + */ +static ulong flash_get_size (unsigned char * addr, flash_info_t * info); +static int write_data (flash_info_t * info, ulong dest, unsigned char data); +static void flash_get_offsets (ulong base, flash_info_t * info); +void inline spin_wheel (void); + +/*----------------------------------------------------------------------- + */ + +unsigned long flash_init (void) +{ + int i; + ulong size = 0; + + for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) { + switch (i) { + case 0: + flash_get_size ((unsigned char *) PHYS_FLASH_1, &flash_info[i]); + flash_get_offsets (PHYS_FLASH_1, &flash_info[i]); + break; + case 1: + /* ignore for now */ + flash_info[i].flash_id = FLASH_UNKNOWN; + break; + default: + panic ("configured too many flash banks!\n"); + break; + } + size += flash_info[i].size; + } + + /* Protect monitor and environment sectors + */ + flash_protect (FLAG_PROTECT_SET, + CFG_FLASH_BASE, + CFG_FLASH_BASE + _bss_start - _armboot_start, + &flash_info[0]); + + return size; +} + +/*----------------------------------------------------------------------- + */ +static void flash_get_offsets (ulong base, flash_info_t * info) +{ + int i; + + if (info->flash_id == FLASH_UNKNOWN) + return; + + if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) { + for (i = 0; i < info->sector_count; i++) { + info->start[i] = base + (i * PHYS_FLASH_SECT_SIZE); + info->protect[i] = 0; + } + } +} + +/*----------------------------------------------------------------------- + */ +void flash_print_info (flash_info_t * info) +{ + int i; + + if (info->flash_id == FLASH_UNKNOWN) { + printf ("missing or unknown FLASH type\n"); + return; + } + + switch (info->flash_id & FLASH_VENDMASK) { + case FLASH_MAN_INTEL: + printf ("INTEL "); + break; + default: + printf ("Unknown Vendor "); + break; + } + + switch (info->flash_id & FLASH_TYPEMASK) { + case FLASH_28F128J3A: + printf ("28F128J3A\n"); + break; + default: + printf ("Unknown Chip Type\n"); + break; + } + + printf (" Size: %ld MB in %d Sectors\n", + info->size >> 20, info->sector_count); + + printf (" Sector Start Addresses:"); + for (i = 0; i < info->sector_count; ++i) { + if ((i % 5) == 0) + printf ("\n "); + printf (" %08lX%s", + info->start[i], info->protect[i] ? " (RO)" : " "); + } + printf ("\n"); + return; +} + +/* + * The following code cannot be run from FLASH! + */ +static ulong flash_get_size (unsigned char * addr, flash_info_t * info) +{ + volatile unsigned char value; + + /* Write auto select command: read Manufacturer ID */ + addr[0x5555] = 0xAA; + addr[0x2AAA] = 0x55; + addr[0x5555] = 0x90; + + mb (); + value = addr[0]; + + switch (value) { + + case (unsigned char)INTEL_MANUFACT: + info->flash_id = FLASH_MAN_INTEL; + break; + + default: + info->flash_id = FLASH_UNKNOWN; + info->sector_count = 0; + info->size = 0; + addr[0] = 0xFF; /* restore read mode */ + return (0); /* no or unknown flash */ + } + + mb (); + value = addr[2]; /* device ID */ + + switch (value) { + + case (unsigned char)INTEL_ID_28F640J3A: + info->flash_id += FLASH_28F640J3A; + info->sector_count = 64; + info->size = 0x00800000; + break; /* => 8 MB */ + + case (unsigned char)INTEL_ID_28F128J3A: + info->flash_id += FLASH_28F128J3A; + info->sector_count = 128; + info->size = 0x01000000; + break; /* => 16 MB */ + + default: + info->flash_id = FLASH_UNKNOWN; + break; + } + + if (info->sector_count > CFG_MAX_FLASH_SECT) { + printf ("** ERROR: sector count %d > max (%d) **\n", + info->sector_count, CFG_MAX_FLASH_SECT); + info->sector_count = CFG_MAX_FLASH_SECT; + } + + addr[0] = 0xFF; /* restore read mode */ + + return (info->size); +} + + +/*----------------------------------------------------------------------- + */ + +int flash_erase (flash_info_t * info, int s_first, int s_last) +{ + int flag, prot, sect; + ulong type; + int rcode = 0; + + if ((s_first < 0) || (s_first > s_last)) { + if (info->flash_id == FLASH_UNKNOWN) { + printf ("- missing\n"); + } else { + printf ("- no sectors to erase\n"); + } + return 1; + } + + type = (info->flash_id & FLASH_VENDMASK); + if ((type != FLASH_MAN_INTEL)) { + printf ("Can't erase unknown flash type %08lx - aborted\n", + info->flash_id); + return 1; + } + + prot = 0; + for (sect = s_first; sect <= s_last; ++sect) { + if (info->protect[sect]) { + prot++; + } + } + + if (prot) + printf ("- Warning: %d protected sectors will not be erased!\n", prot); + else + printf ("\n"); + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts (); + + /* Start erase on unprotected sectors */ + for (sect = s_first; sect <= s_last; sect++) { + if (info->protect[sect] == 0) { /* not protected */ + volatile unsigned char *addr; + unsigned char status; + + printf ("Erasing sector %2d ... ", sect); + + /* arm simple, non interrupt dependent timer */ + reset_timer_masked (); + + addr = (volatile unsigned char *) (info->start[sect]); + *addr = 0x50; /* clear status register */ + *addr = 0x20; /* erase setup */ + *addr = 0xD0; /* erase confirm */ + + while (((status = *addr) & 0x80) != 0x80) { + if (get_timer_masked () > + CFG_FLASH_ERASE_TOUT) { + printf ("Timeout\n"); + *addr = 0xB0; /* suspend erase */ + *addr = 0xFF; /* reset to read mode */ + rcode = 1; + break; + } + } + + *addr = 0x50; /* clear status register cmd */ + *addr = 0xFF; /* resest to read mode */ + + printf (" done\n"); + } + } + return rcode; +} + +/*----------------------------------------------------------------------- + * Copy memory to flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + * 4 - Flash not identified + */ + +int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt) +{ + ulong cp, wp; + unsigned char data; + int count, i, l, rc, port_width; + + if (info->flash_id == FLASH_UNKNOWN) + return 4; + + wp = addr; + port_width = 1; + + /* + * handle unaligned start bytes + */ + if ((l = addr - wp) != 0) { + data = 0; + for (i = 0, cp = wp; i < l; ++i, ++cp) { + data = (data << 8) | (*(uchar *) cp); + } + for (; i < port_width && cnt > 0; ++i) { + data = (data << 8) | *src++; + --cnt; + ++cp; + } + for (; cnt == 0 && i < port_width; ++i, ++cp) { + data = (data << 8) | (*(uchar *) cp); + } + + if ((rc = write_data (info, wp, data)) != 0) { + return (rc); + } + wp += port_width; + } + + /* + * handle word aligned part + */ + count = 0; + while (cnt >= port_width) { + data = 0; + for (i = 0; i < port_width; ++i) { + data = (data << 8) | *src++; + } + if ((rc = write_data (info, wp, data)) != 0) { + return (rc); + } + wp += port_width; + cnt -= port_width; + if (count++ > 0x800) { + spin_wheel (); + count = 0; + } + } + + if (cnt == 0) { + return (0); + } + + /* + * handle unaligned tail bytes + */ + data = 0; + for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) { + data = (data << 8) | *src++; + --cnt; + } + for (; i < port_width; ++i, ++cp) { + data = (data << 8) | (*(uchar *) cp); + } + + return (write_data (info, wp, data)); +} + +/*----------------------------------------------------------------------- + * Write a word or halfword to Flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ +static int write_data (flash_info_t * info, ulong dest, unsigned char data) +{ + volatile unsigned char *addr = (volatile unsigned char *) dest; + ulong status; + int flag; + + /* Check if Flash is (sufficiently) erased */ + if ((*addr & data) != data) { + printf ("not erased at %08lx (%lx)\n", (ulong) addr, + (ulong) * addr); + return (2); + } + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts (); + + *addr = 0x40; /* write setup */ + *addr = data; + + /* arm simple, non interrupt dependent timer */ + reset_timer_masked (); + + /* wait while polling the status register */ + while (((status = *addr) & 0x80) != 0x80) { + if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) { + *addr = 0xFF; /* restore read mode */ + return (1); + } + } + + *addr = 0xFF; /* restore read mode */ + + return (0); +} + +void inline spin_wheel (void) +{ + static int p = 0; + static char w[] = "\\/-"; + + printf ("\010%c", w[p]); + (++p == 3) ? (p = 0) : 0; +} diff -Naur --exclude=CVS u-boot-1.1.1/board/cm4008/Makefile u-boot/board/cm4008/Makefile --- u-boot-1.1.1/board/cm4008/Makefile 1970-01-01 10:00:00.000000000 +1000 +++ u-boot/board/cm4008/Makefile 2004-11-02 00:38:51.000000000 +1000 @@ -0,0 +1,46 @@ +# +# (C) Copyright 2000, 2002 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = lib$(BOARD).a + +OBJS := cm4008.o flash.o + +$(LIB): $(OBJS) $(SOBJS) + $(AR) crv $@ $^ + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) + $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ + +-include .depend + +######################################################################### diff -Naur --exclude=CVS u-boot-1.1.1/board/cm4008/u-boot.lds u-boot/board/cm4008/u-boot.lds --- u-boot-1.1.1/board/cm4008/u-boot.lds 1970-01-01 10:00:00.000000000 +1000 +++ u-boot/board/cm4008/u-boot.lds 2004-11-05 00:27:11.000000000 +1000 @@ -0,0 +1,55 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + cpu/ks8695/start.o (.text) + *(.text) + } + + . = ALIGN(4); + .rodata : { *(.rodata) } + + . = ALIGN(4); + .data : { *(.data) } + + . = ALIGN(4); + .got : { *(.got) } + + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff -Naur --exclude=CVS u-boot-1.1.1/include/configs/cm4008.h u-boot/include/configs/cm4008.h --- u-boot-1.1.1/include/configs/cm4008.h 1970-01-01 10:00:00.000000000 +1000 +++ u-boot/include/configs/cm4008.h 2005-03-20 22:31:27.000000000 +1000 @@ -0,0 +1,127 @@ +/* + * (C) Copyright 2004 + * Greg Ungerer <greg.ungerer(a)opengear.com>. + * Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * If we are developing, we might want to start armboot from ram + * so we MUST NOT initialize critical regs like mem-timing ... + */ +#define CONFIG_INIT_CRITICAL /* undef for developing */ + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_KS8695 1 /* it is a KS8695 CPU */ +#define CONFIG_CM4008 1 /* it is an OpenGear CM4008 boad */ + +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 + +/* + * Size of malloc() pool + */ +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024) +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ + +/* + * Hardware drivers + */ + +/* + * select serial console configuration + */ +#define CFG_ENV_IS_NOWHERE +#define CONFIG_SERIAL1 +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> +#undef CONFIG_COMMANDS +#define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~(CFG_CMD_NONSTD | CFG_CMD_ENV)) + +#define CONFIG_BOOTDELAY 0 +#define CONFIG_BOOTARGS "mem=16M console=ttyAM0,115200" +#define CONFIG_BOOTCOMMAND "gofsk 0x02200000" + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "boot > " /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00800000 /* memtest works on */ +#define CFG_MEMTEST_END 0x01000000 /* 16 MB in DRAM */ + +#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR 0x00008000 /* default load address */ + +#define CFG_HZ (1000) /* 1ms resolution ticks */ + +/*----------------------------------------------------------------------- + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + +/*----------------------------------------------------------------------- + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x01000000 /* 16 MB */ + +#define PHYS_FLASH_1 0x02000000 /* Flash Bank #1 */ +#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 128 KB sectors (x1) */ +#define CFG_FLASH_BASE PHYS_FLASH_1 + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of flash banks */ +#define CFG_MAX_FLASH_SECT (128) /* max number of sectors on one chip */ + +/* timeout values are in ticks */ +#define CFG_FLASH_ERASE_TOUT (20*CFG_HZ) /* Timeout for Flash Erase */ +#define CFG_FLASH_WRITE_TOUT (20*CFG_HZ) /* Timeout for Flash Write */ + +#define CFG_ENV_SIZE 0x20000 /* Total Size of Environment */ + +#endif /* __CONFIG_H */ diff -Naur --exclude=CVS u-boot-1.1.1/Makefile u-boot/Makefile --- u-boot-1.1.1/Makefile 2004-04-25 09:23:30.000000000 +1000 +++ u-boot/Makefile 2005-03-12 23:06:59.000000000 +1000 @@ -1040,6 +1040,11 @@ VCMA9_config : unconfig @./mkconfig $(@:_config=) arm arm920t vcma9 mpl +cm4008_config : unconfig + @./mkconfig $(@:_config=) arm ks8695 cm4008 + +cm41xx_config : unconfig + @./mkconfig $(@:_config=) arm ks8695 cm41xx ######################################################################### ## S3C44B0 Systems

2 16

[U-Boot-Users] [PATCH] revised word alignment fixes for word aligned NS16550 UART
by jean-paul.saman＠philips.com 12 Mar '06

12 Mar '06

The patch is created against current CVS 2005 march 1st and fixes problems for boards that only have word access to the NS16550 UART. OBSOLETES: From: Jean-Paul Saman Date: 23-02-2005 Subject: [PATCH] word alignment fixes for word aligned NS16550 UART peripheral CHANGELOG: * Patch by Jean-Paul Saman, 23 Feb 2005 - include/ns16550.h Fixes alignement bug with UART that only supports word aligned access: removed "__attribute__ ((packed));" for "(CFG_NS16550_REG_SIZE == 4)" GCC generates bytes access when it encounters the packed attribute regardless if the struct is already word aligned for a platform. Peripherals that can only handle word aligned access won't work properly when accessed with byte access. The struct NS16550 is already word aligned for REG_SIZE = 4, so there is no need to packed the struct in that case. Kind greetings, Jean-Paul Saman Philips Semiconductors CTO/RTG Philips HighTech Campus, building WDB 3.29 Professor van den Holstlaan 4 5655 AA Eindhoven tel: +31 (0)40 27 45131

2 1

[U-Boot-Users] Suspect behaiviour if gatewayip not set
by Robin Gilks 12 Mar '06

12 Mar '06

Greetings Having played with netconsole a bit, I've observed that the current behaiviour of warning if gatewayip is not set and then using its value of zero when talking to outside the current subnet is somewhat suspect. The particular case of netconsole means that no error message is evident - it is trying to be sent the error down the ethernet connection that is being initiated with an arp(0.0.0.0)! I propose that the warning message stay but the target address is put into the arp so that a proxying router can reply to it rather then send out a nonsense arp request. CHANGELOGg: * Patch by Robin Gilks 23 December 2004 net.c - if gatewayip not set send arp request for destination IP not zero --- net.c.old 2004-10-26 12:46:58.000000000 +1300 +++ net.c 2004-12-23 09:42:46.000000000 +1300 @@ -207,8 +207,10 @@ (NetOurIP & NetOurSubnetMask)) { if (NetOurGatewayIP == 0) { puts ("## Warning: gatewayip needed but not set\n"); + NetArpWaitReplyIP = NetArpWaitPacketIP; + } else { + NetArpWaitReplyIP = NetOurGatewayIP; } - NetArpWaitReplyIP = NetOurGatewayIP; } else { NetArpWaitReplyIP = NetArpWaitPacketIP; } -- Robin Gilks Senior Design Engineer Phone: (+64)(3) 357 1569 Tait Electronics Fax : (+64)(3) 359 4632 PO Box 1645 Christchurch Email : robin.gilks(a)tait.co.nz New Zealand ======================================================================= This email, including any attachments, is only for the intended addressee. It is subject to copyright, is confidential and may be the subject of legal or other privilege, none of which is waived or lost by reason of this transmission. If the receiver is not the intended addressee, please accept our apologies, notify us by return, delete all copies and perform no other act on the email. Unfortunately, we cannot warrant that the email has not been altered or corrupted during transmission. =======================================================================

2 1

[U-Boot-Users] maybe just one more bug left in building the examples directory in 1.1.2
by John Davis 08 Mar '06

08 Mar '06

Hello I am getting closer to getting the examples code to build. I have added a bunch of object files and library files to the link command in the examples Makefile. However, I have gotten to the last bug and I don't know how to solve it. Below, it complains about __got2_entries. I found this defined in our board directories linker script. The current command line and results: make[1]: Entering directory `/home/davis/cvs/mcp4/uboot/mine/u-boot-1.1.2 /examples' ppc-linux-ld -g -Ttext 0x40000 \ -o hello_world -e hello_world hello_world.o libstubs.a \ /home/davis/cvs/mcp4/uboot/mine/u-boot-1.1.2/cpu/ppc4xx/start.o \ /home/davis/cvs/mcp4/uboot/mine/u-boot-1.1.2/board/fsp1/fsp1_pra.o \ /home/davis/cvs/mcp4/uboot/mine/u-boot-1.1.2/board/fsp1/eddr2.o \ -L/home/davis/cvs/mcp4/uboot/mine/u-boot-1.1.2/common -lcommon \ -L/home/davis/cvs/mcp4/uboot/mine/u-boot-1.1.2/lib_generic -lgeneric \ -L/home/davis/cvs/mcp4/uboot/mine/u-boot-1.1.2/net -lnet \ -L/home/davis/cvs/mcp4/uboot/mine/u-boot-1.1.2/rtc -lrtc \ -L/home/davis/cvs/mcp4/uboot/mine/u-boot-1.1.2/board/fsp1 -lfsp1 \ -L/home/davis/cvs/mcp4/uboot/mine/u-boot-1.1.2/cpu/ppc4xx -lppc4xx \ -L/home/davis/cvs/mcp4/uboot/mine/u-boot-1.1.2/lib_ppc -lppc \ -L/opt/fld_fakeroot/opt/mcp/ppc/bin/../lib/gcc-lib/ppc-linux/3.3.3 -lgcc /home/davis/cvs/mcp4/uboot/mine/u-boot-1.1.2 /cpu/ppc4xx/start.o(.text+0x25ae):/home/davis/cvs/mcp4/uboot/mine/u- boot-1.1.2/cpu/ppc4xx/start.S:1374: undefined reference to `__got2_entries' ppc-linux-ld: BFD 2.15.90.0.1.1 20040303 (SuSE Linux) assertion fail ../../bfd/elf32-ppc.c:5645 make[1]: *** [hello_world] Segmentation fault make[1]: *** Deleting file `hello_world' make[1]: Leaving directory `/home/davis/cvs/mcp4/uboot/mine/u-boot-1.1.2 /examples' make: *** [examples] Error 2 [davis@dyn-9-152-249-44 u-boot-1.1.2]$ The relevant portion of the linker script which defines the __got2_entries variable. board/fsp1/u-boot.lds: ... stuff snipped __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; ... stuff snipped Any advice on how to apply this to my makefile is appreciated. JD

4 10

[U-Boot-Users] [PATCH] CFI support for Versatile & Integrator/CP boards
by Peter Pearse 28 Feb '06

28 Feb '06

The attached gzipped patch was made against the U-Boot GIT head of Oct 31 2005. It is my patch number 012. The patch is independent of patches 009 & 010, but dependent on patch 011. The patch updates the versatile and integrator/CP boards code to use CFI flash, rather than having a hardware dependent flash.c. CHANGELOG: Versatile & Integrator/CP to use CFI flash.. Patch by Peter Pearse, 31st Oct 2005

6 11