This patch enables DM I2C for DHCOM i.MX6 PDK2 boards and removes non DM I2C code. The only I2C EEPROM with ethaddr (MAC) is defined in the device tree. Use UCLASS_I2C_EEPROM to find and read the ethaddr.

Tested with DHCOM i.MX6dl and DHCOM i.MX6q.

Signed-off-by: Ludwig Zenz lzenz@dh-electronics.com --- Changes in v2: - Remove default i2c bus from dh_imx6_defconfig - Remove CONFIG_SYS_I2C_MXC_I2Cx from dh_imx6_defconfig - Disable CONFIG_SPL_I2C_SUPPORT (SPL does not need I2C) - Enable CONFIG_MISC, CONFIG_I2C_EEPROM to handle ethaddr --- board/dhelectronics/dh_imx6/dh_imx6.c | 108 ++-------------------------------- configs/dh_imx6_defconfig | 5 +- include/configs/dh_imx6.h | 8 --- 3 files changed, 9 insertions(+), 112 deletions(-)

diff --git a/board/dhelectronics/dh_imx6/dh_imx6.c b/board/dhelectronics/dh_imx6/dh_imx6.c index cca8e832ec..d2f38a2459 100644 --- a/board/dhelectronics/dh_imx6/dh_imx6.c +++ b/board/dhelectronics/dh_imx6/dh_imx6.c @@ -18,7 +18,6 @@ #include <asm/io.h> #include <asm/mach-imx/boot_mode.h> #include <asm/mach-imx/iomux-v3.h> -#include <asm/mach-imx/mxc_i2c.h> #include <asm/mach-imx/sata.h> #include <ahci.h> #include <dwc_ahsata.h> @@ -26,7 +25,7 @@ #include <errno.h> #include <fsl_esdhc.h> #include <fuse.h> -#include <i2c.h> +#include <i2c_eeprom.h> #include <miiphy.h> #include <mmc.h> #include <net.h> @@ -36,92 +35,6 @@

DECLARE_GLOBAL_DATA_PTR;

-#define I2C_PAD_CTRL \ - (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ - PAD_CTL_HYS | PAD_CTL_ODE | PAD_CTL_SRE_FAST) - -#define EEPROM_I2C_ADDRESS 0x50 - -#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) - -static struct i2c_pads_info dh6sdl_i2c_pad_info0 = { - .scl = { - .i2c_mode = MX6DL_PAD_EIM_D21__I2C1_SCL | PC, - .gpio_mode = MX6DL_PAD_EIM_D21__GPIO3_IO21 | PC, - .gp = IMX_GPIO_NR(3, 21) - }, - .sda = { - .i2c_mode = MX6DL_PAD_EIM_D28__I2C1_SDA | PC, - .gpio_mode = MX6DL_PAD_EIM_D28__GPIO3_IO28 | PC, - .gp = IMX_GPIO_NR(3, 28) - } -}; - -static struct i2c_pads_info dh6sdl_i2c_pad_info1 = { - .scl = { - .i2c_mode = MX6DL_PAD_KEY_COL3__I2C2_SCL | PC, - .gpio_mode = MX6DL_PAD_KEY_COL3__GPIO4_IO12 | PC, - .gp = IMX_GPIO_NR(4, 12) - }, - .sda = { - .i2c_mode = MX6DL_PAD_KEY_ROW3__I2C2_SDA | PC, - .gpio_mode = MX6DL_PAD_KEY_ROW3__GPIO4_IO13 | PC, - .gp = IMX_GPIO_NR(4, 13) - } -}; - -static struct i2c_pads_info dh6sdl_i2c_pad_info2 = { - .scl = { - .i2c_mode = MX6DL_PAD_GPIO_3__I2C3_SCL | PC, - .gpio_mode = MX6DL_PAD_GPIO_3__GPIO1_IO03 | PC, - .gp = IMX_GPIO_NR(1, 3) - }, - .sda = { - .i2c_mode = MX6DL_PAD_GPIO_6__I2C3_SDA | PC, - .gpio_mode = MX6DL_PAD_GPIO_6__GPIO1_IO06 | PC, - .gp = IMX_GPIO_NR(1, 6) - } -}; - -static struct i2c_pads_info dh6dq_i2c_pad_info0 = { - .scl = { - .i2c_mode = MX6Q_PAD_EIM_D21__I2C1_SCL | PC, - .gpio_mode = MX6Q_PAD_EIM_D21__GPIO3_IO21 | PC, - .gp = IMX_GPIO_NR(3, 21) - }, - .sda = { - .i2c_mode = MX6Q_PAD_EIM_D28__I2C1_SDA | PC, - .gpio_mode = MX6Q_PAD_EIM_D28__GPIO3_IO28 | PC, - .gp = IMX_GPIO_NR(3, 28) - } -}; - -static struct i2c_pads_info dh6dq_i2c_pad_info1 = { - .scl = { - .i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL | PC, - .gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12 | PC, - .gp = IMX_GPIO_NR(4, 12) - }, - .sda = { - .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | PC, - .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | PC, - .gp = IMX_GPIO_NR(4, 13) - } -}; - -static struct i2c_pads_info dh6dq_i2c_pad_info2 = { - .scl = { - .i2c_mode = MX6Q_PAD_GPIO_3__I2C3_SCL | PC, - .gpio_mode = MX6Q_PAD_GPIO_3__GPIO1_IO03 | PC, - .gp = IMX_GPIO_NR(1, 3) - }, - .sda = { - .i2c_mode = MX6Q_PAD_GPIO_6__I2C3_SDA | PC, - .gpio_mode = MX6Q_PAD_GPIO_6__GPIO1_IO06 | PC, - .gp = IMX_GPIO_NR(1, 6) - } -}; - int dram_init(void) { gd->ram_size = imx_ddr_size(); @@ -214,6 +127,7 @@ int board_usb_phy_mode(int port)

static int setup_dhcom_mac_from_fuse(void) { + struct udevice *dev; unsigned char enetaddr[6]; int ret;

@@ -228,13 +142,13 @@ static int setup_dhcom_mac_from_fuse(void) return 0; }

- ret = i2c_set_bus_num(2); + ret = uclass_first_device_err(UCLASS_I2C_EEPROM, &dev); if (ret) { - printf("Error switching I2C bus!\n"); + printf("Cannot find EEPROM!\n"); return ret; }

- ret = i2c_read(EEPROM_I2C_ADDRESS, 0xfa, 0x1, enetaddr, 0x6); + ret = i2c_eeprom_read(dev, 0xfa, enetaddr, 0x6); if (ret) { printf("Error reading configuration EEPROM!\n"); return ret; @@ -265,18 +179,6 @@ int board_init(void) /* Enable eim_slow clocks */ setbits_le32(&mxc_ccm->CCGR6, 0x1 << MXC_CCM_CCGR6_EMI_SLOW_OFFSET);

-#ifdef CONFIG_SYS_I2C_MXC - if (is_mx6dq()) { - setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &dh6dq_i2c_pad_info0); - setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &dh6dq_i2c_pad_info1); - setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &dh6dq_i2c_pad_info2); - } else { - setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &dh6sdl_i2c_pad_info0); - setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &dh6sdl_i2c_pad_info1); - setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &dh6sdl_i2c_pad_info2); - } -#endif - setup_dhcom_mac_from_fuse();

return 0; diff --git a/configs/dh_imx6_defconfig b/configs/dh_imx6_defconfig index 4734ed76e5..6a7a40d166 100644 --- a/configs/dh_imx6_defconfig +++ b/configs/dh_imx6_defconfig @@ -23,7 +23,6 @@ CONFIG_BOOTDELAY=3 CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y CONFIG_BOUNCE_BUFFER=y CONFIG_SPL_TEXT_BASE=0x00908000 -CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_SPI_LOAD=y CONFIG_SPL_WATCHDOG_SUPPORT=y CONFIG_CMD_MEMTEST=y @@ -48,6 +47,10 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_DWC_AHSATA=y CONFIG_BOOTCOUNT_LIMIT=y CONFIG_DM_GPIO=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_MXC=y +CONFIG_MISC=y +CONFIG_I2C_EEPROM=y CONFIG_DM_MMC=y CONFIG_FSL_ESDHC=y CONFIG_DM_SPI_FLASH=y diff --git a/include/configs/dh_imx6.h b/include/configs/dh_imx6.h index 3b1d0a99a1..7d2e573846 100644 --- a/include/configs/dh_imx6.h +++ b/include/configs/dh_imx6.h @@ -48,14 +48,6 @@ #define CONFIG_FEC_MXC_PHYADDR 0 #define CONFIG_ARP_TIMEOUT 200UL

-/* I2C Configs */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ -#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ -#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ -#define CONFIG_SYS_I2C_SPEED 100000 - /* MMC Configs */ #define CONFIG_FSL_USDHC #define CONFIG_SYS_FSL_ESDHC_ADDR 0